Radar Viii Sem Ece

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Q Explain radar range equation.

The radar range equation relates the range of the radar to the characteristics of the transmitter,
receiver, antenna, target and the environment. It is used as a tool to help in specifying radar
subsystem specifications in the design phase of a program. Free space condition implies that the
radar set and the target are isolated in an unbounded empty space. The condition is realized well
enough for practical purposes if the following conditions are fulfilled:
(a) No large obstacles lie between antenna and the target along an optical line of sight.
(b) No alternative trasmission path via any reflecting surface can be followed by a substantial
fraction of the total radiated energy.
(c) The intervening medium is transparent, i.e., it does not absorb energy from the
electromagnetic waves at the frequency used.
(d) The intervening medium is homogeneous with respect to the refractive index at the radar
frequency.
If the transmitter delivers PT watts power into an isotropic antenna (one which radiates power
uniformly in an directions is used), then the power density (W/m2) at a distance R from the
radar is

here the 4πR2 represents the surface area of the sphere at distance R. Radars employ directional
antennas to channel the radiated power PT in a particular direction. The gain GT of an antenna
is the measure of the increased power radiated in the direction of the target, compared to the
power that would have been radiated from an isotropic antenna. So power density from a
directional antenna

This energy is incident on the target and gets scattered in various directions. A part of the
energy returns in the direction of the radar antennas. The target is usually described in terms of
an equivalent cross-section σ such that if the total power contained in a section of the incident
wavefront having the area σ were radiated by an isotropic radiator located at the target the
strength of the radio wave reaching the radar receiving antenna would be the same as the
strength of the actual echo produced by target.
Area σ is then referred to as the effective echo area of the target. Hence the power density of the
echo signal at the radar

The receiving antenna effectively intercepts the power of the echo signal at the radar over a
certain area called the effective area Ae. Since the power density (watts/m2) is intercepted
across an area Ae, the power delivered to the receiver is
RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Equation (12.4) is the free space radar equation.


Now the maximum range Rmax is the distance beyond which the target cannot be detected due
to insufficient received power Pr. The minimum power which the receiver can detect is called
the minimum detectable signal Smin. Setting Pr = Smin and rearranging the above equation
gives
RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Q. Explain Block Diagram of RADAR system.


RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Q. Give the detail of frequency range use in RADAR.


RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Q. Explain MTI RADAR.


RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

A block diagram of an MTI radar is shown in Fig. The block diagram shows two mixers.
Mixer 2 generates the transmitter frequency (fo + fc), which is obtained by the sum of
frequencies produced by two oscillators. The first is STALO (stable oscillator) producing fo and
second is the COHO (Coherent oscillator ) producing fc. The transmitted frequency drives a
multicavity klystron amplifier, which acts as an output tube. This amplifier provides the desired
amplification for proving a high power pulse when modulator switches on the tube. The
transmitter pulse is the output via the duplexer.

The echo pulse from the target (due to transmitted pulse) is received by the MTI radar
antenna. If the echo is due to a moving target, the echo pulse undergoes a doppler frequency
shift. The received echo pulses (fo + fc ± fd) then pass through mixer 1 of the receiver which
hytrodynes the received signal of frequency (f0 + fc + fd) with the output of STALO at f0 and
produces a difference frequency (fc ± fd) at its output. These two mixers 1 and 2 are identical in
all respects except that mixer 1 produces a difference frequency whereas mixer 2 produces a
sum frequency. This difference frequency signal is further amplified by an IF amplifier and is
given to the phase sensitive detector or phase discriminator. This detector compares the IF
signal with the reference signal from the COHO oscillator. This difference is the doppler
frequency. The detector provides an output depending upon the phase difference between these
two signals. Since all received signal pulses will have phase difference compared with the
transmitted pulse, the phase detector gives output for both fixed and also for moving targets.
Phase difference is constant for all fixed targets but varies for moving targets. Doppler
frequency shift causes this variation in phase difference. A change of half cycle in the doppler
frequency shift would cause an output of opposite polarity in the phase detector output. The
output of the phase detector therefore successive pulses in case of a moving target. However,
for fixed targets the magnitude and polarity of the output will remain the same for all
transmitted pulses. In Fig. 2 that those returns of each pulse that correspond to stationary targets
are identical with each pulse, but those portions corresponding to moving targets keep changing
in phase. It is thus possible to subtract the output for each pulse from the preceding one, by
delaying the earlier output by a time equal to the pulse interval, or 1/PRF. Since the delay line
also attenuates heavily and since signals must be of the same amplitude if permanent echoes are
to cancel an amplifier follows the delay line. To ensure that this does not introduce a spurious
phase shift, an amplifier is placed in the undelayed line, which has exactly the same response
characteristics than amplifier 1. The delayed and undelayed signals are compared in the
subtractor,
RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

Q. Explain the application of RADAR.

1 Air Traffic Control (ATC): Radar used to provide air traffic controllers with position and
other information on aircraft flying within their area of responsibility (airways and in the
vicinity of airports). The high resolution radar is used at large airports to monitor aircraft and
ground vehicles on the runways, taxiways and ramps. The GCA (ground controlled approach)
or PAR (precision approach radar) provides on operator with high accuracy aircraft position
information in both the vertical and horizontal. The operator uses this information to guide the
aircraft to a landing in bad weather. The MLS (microwave landing system) and ATC radar
beacon systems are based on radar technology.

2. Air Navigation: The weather avoidance radar is used on aircraft to detect and display areas
of heavy precipitation and turbulence. Low-flying military aircraft rely on terrain avoidance and
terrain following radars to avoid colliding with obstructions or high terrain. Military aircraft
employ ground-mapping radars to image a scene. The radio altimeter is also a radar used to
indicate the height of an aircraft above the terrain and as a part of self contained guidance
system over land.

3. Ship Safety: There are one of the least expensive, most reliable and largest applications of
radar. Radar is found on ships and boats for collision avoidance and to observe navigation
buoys, especially when the visibility is poor. The automatic detection and tracking equipments
are available with these radars for collision avoidance. Similarly shore based radars of moderate
resolution are used from harbour surveilliance.

4. Space: Radars are used for rendezvous and dockign and was used for landing on the moon.
The large ground based radars are used for detection and tracking of satellites. The satellite-
borne radars used for remote sensing (SAR, Synthetic Aperture Radar).

5. Remote Sensing: All radars are remote sensors, and used for sensing geophysical objects
(the environment). The radar astronomy are used to probe the moon and planets. The earth
resources monitoring radars measure and map sea conditions, water resources, ice cover,
agricultural land use, forest conditions, geological formations, environmental pollution
(Synthetic Aperture Radar, SAR and Side Looking Airborne Radar, SLAR).

6. Law Enforcement: The radar speed meter, familiar to many, is used by police for enforcing
speed limits. Radar has been considered for making vehicles safer by warning of ponding
collision, actuating the air bag, or warning of obstructions or people behind a vehicle or in the
side blind zone. It is also employed for detection of intruders.

7. Military: Radar is an important part of air-defence systems as well as the operation of


offensive missiles and other weapons. In air defence it performs the functions of surveillance
and weapon control. Surveillance includes target detection, target recognition, target tracking,
RADAR & TV ENGINEERING VIII SEM ECE N K VYAS

and designation to a weapon system. Weapon-control radars track targets, direct the weapon to
an intercept, and assess the effectiveness of the engagement (called battle damage assessment).
A missile system might employ radar methods for guidance and fuzing of the weapon. High
resolution imaging radars, such as synthetic aperture radar, have been used for reconnaissance
purpose and for detecting fixed and moving targets on the battle field.

You might also like