ETABS 21.2.

Connection Design: B9-CJ

Story: Story3

Design Code: AISC 360-16

Beam-Column Moment Major Axis Connection

Summary of Results (DStlS2)

Check Design Check Type D/C Ratio Result Reference
1 Strength of the Bolted Connection - Plate 0.129 Passed Spec. J3.6, J3.10
2 Shear Yielding of the Plate 0.128 Passed Spec. J4.2
3 Shear Rupture of the Plate 0.231 Passed Spec. J4.2
4 Block Shear Rupture of the Plate 0.204 Passed Spec. J4.3
5 Strength of the Bolted Connection - Beam Web 0.211 Passed Spec. J3.6, J3.10
6 Shear Yielding of Beam Web 0.223 Passed Spec. J4.2
7 Shear Rupture of the Beam Web 0.316 Passed Sec. J4.2
8 Block Shear Rupture of the Beam Web 0.386 Passed Spec. J4.3
9 Flexural Strength of Beam 0.179 Passed Spec. F13
10 Weld Strength 0.177 Passed Spec. J2.4
11 Strength of Column at Weld 0.312 Passed Manual Part 9
12 Column Flange Local Bending 0.344 Passed Spec. J10.1
13 Column Web Local Yielding 0.585 Passed Spec. J10.2
14 Column Web Local Crippling 0.239 Passed Spec. J10.3
15 Web Panel-Zone Shear 0.301 Passed Spec. J10.6

Material and Geometric Properties

Beam Column Plate
Section = IPE400 Section = HE400A Material = S355
Material = S235 Material = S235 Yield Stress, Fy = 355 MPa
Yield Stress, Fy = 235 MPa Yield Stress, Fy = 235 MPa Tensile Strength, Fu = 510 MPa
Tensile Strength, Fu = 360 MPa Tensile Strength, Fu = 360 MPa Plate Height = 287.6 mm
Section Depth, d = 400 mm Section Depth, d = 390 mm Plate Width = 87.5 mm
Flange Width, bf = 180 mm Flange Width, bf = 300 mm Thickness, tp = 12.5 mm
Web Thickness, tw = 8.6 mm Web Thickness, tw = 11 mm
Flange Thickness, tf = 13.5 mm Flange Thickness, tf = 19 mm

Page 1 of 8 12/12/2023
ETABS 21.2.0

Bolts Single Plate Weld

Bolt Quantity, n =4 Material = E70XX
Bolt Type = A325-N Weld Size, D(1/16) = 100 mm
Bold Diameter, db = 32 mm Strength, Fexx = 70 MPa
Hole Type = STD
Hole Diameter, dh = 33.3 mm
Bolt Spacing, s = 75 mm
Bolt Offset, Lev = 31.3 mm
Bolt Offset, Leh = 37.5 mm
Bolt H. Distance, a = 2 mm

Design Calculations (DStlS2)

Design Forces

Pu -3.8519 kN Vu 97.8522 kN Mu -63.424 kN-m

1-Strength of the Bolted Connection - Plate (Spec. J3.6, J3.10)

Bolt Shear Strength (Spec. Eq. J3-1)

πdb 2 3.14*322
Ab Ab Ab 8 cm²
4 4
ϕrnshear ϕFnv Ab

ϕrnshear 0.75*372.32*8 ϕrnshear 224.5763 kN

Bolt Bearing Strength (Spec. Eq. J3-6)

ϕrnbearing ϕ 2.4db tFu

ϕrnbearing 0.75 2.4*32*12.5*510 ϕrnbearing 367.2 kN

Edge Bolt Tearout Strength (Spec. Eq.
J3-6)
dh 33.3
lc Lev - lc 31.3- lc 14.6 mm
2 2
ϕrntear1 ϕ 1.2lc tFu

ϕrntear1 0.75 1.2*14.6*12.5*510 ϕrntear1 83.9468 kN

Middle Bolt Tearout Strength (Spec. Eq.
J3-6)
lc s-dh lc 75-33.3 lc 41.7 mm

ϕrntear2 ϕ 1.2lc tFu

ϕrntear2 0.75 1.2*41.7*12.5*510 ϕrntear2 239.0386 kN

Effective Strength of the Bolt Group

ϕrnmax min ϕrnshear , ϕrnbearing

ϕrnmax min 224.5763,367.2 ϕrnmax 224.5763 kN

ϕRn
min ϕrntear1 , ϕrnmax
n-1 min ϕrntear2 , ϕrnmax

Page 2 of 8 12/12/2023
ETABS 21.2.0

ϕRn
min 83.9468,224.5763
4-1 min 239.0386,224.5763
ϕRn 757.6756 kN
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.129
ϕRn 757.6756
<D/C> Ratio is less than 1, Design is
OK

2-Shear Yielding of the Plate (Spec. J4.2)

Gross Area Subject to Shear

Agv L*t Agv 287.6*12.5 Agv 36 cm²
Shear Yielding Strength (Spec. Eq. J4-
3)
ϕRn ϕ0.6Fy Ag ϕRn 1*0.6*355*36 ϕRn 765.735 kN
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.128
ϕRn 765.735
<D/C> Ratio is less than 1, Design is
OK

3-Shear Rupture of the Plate (Spec. J4.2)

Net Area Subject to Shear

1 1
Anv L-n dh t Anv 287.6-4 33.3 12.5 Anv 18.5 cm²
16 16
Shear Rupture Strength (Spec. Eq. J4-
4)
ϕRn ϕ0.6Fu Anv ϕRn 0.75*0.6*510*18.5 ϕRn 424.2881 kN
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.231
ϕRn 424.2881
<D/C> Ratio is less than 1, Design is
OK

4-Block Shear Rupture of the Plate (Spec. J4.3)

Net Area Subject to Tension

1 1 1 1
Ant Leh - d t Ant 37.5- 33.3 12.5 Ant 2.5 cm²
2 h 16 2 16
Gross Area Subject to Shear
Agv n-1 s Lev t Agv 4-1 75 31.3 12.5 Agv 32 cm²

Net Area Subject to Shear

1 1
Anv n-1 s Lev - n- d t
2 h 16

Page 3 of 8 12/12/2023
ETABS 21.2.0

1
Anv 4-1 75 31.3- 4- 33.3
2 Anv 16.8 cm²
1
12.5
16
Available Strength (Spec. Eq. J4-5)
ϕRn ϕ Fu Ant min 0.6Fy Agv , 0.6Fu Anv
ϕRn
0.75 510*2.5 ϕRn 480.3961 kN
min 0.6*355*32,0.6*510*16.8
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.204
ϕRn 480.3961
<D/C> Ratio is less than 1, Design is
OK

5-Strength of the Bolted Connection - Beam Web (Spec. J3.6, J3.10)

Bolt Shear Strength (Spec. Eq. J3-1)

πdb 2 3.14*322
Ab Ab Ab 8 cm²
4 4
ϕrnshear ϕFnv Ab

ϕrnshear 0.75*372.32*8 ϕrnshear 224.5763 kN

Bolt Bearing Strength (Spec. Eq. J3-6)

ϕrnbearing ϕ 2.4db tFu

ϕrnbearing 0.75 2.4*32*8.6*360 ϕrnbearing 178.3296 kN

Bolt Tearout Strength (Spec. Eq. J3-6)

lc s-dh lc 75-33.3 lc 41.7 mm

ϕrntear ϕ 1.2lc tFu

ϕrntear 0.75 1.2*41.7*8.6*360 ϕrntear 116.0884 kN

Effective Strength of the Bolt Group

ϕRn n*min ϕrnshear , ϕrnbearing , ϕrntear
ϕRn
ϕRn 464.3536 kN
4*min 224.5763,178.3296,116.0884
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.211
ϕRn 464.3536
<D/C> Ratio is less than 1, Design is
OK

6-Shear Yielding of Beam Web (Spec. J4.2)

Length of the Coped Section

h0 d- dct dcb h0 400- 19.1 19.1 h0 361.9 mm

Gross Area Subject to Shear

Agv h0 *t Agv 361.9*8.6 Agv 31.1 cm²

Page 4 of 8 12/12/2023
ETABS 21.2.0

Shear Yielding Strength (Spec. Eq. J4-

3)
ϕRn ϕ0.6Fy Agv ϕRn 1*0.6*235*31.1 ϕRn 438.8399 kN
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.223
ϕRn 438.8399
<D/C> Ratio is less than 1, Design is
OK

7-Shear Rupture of the Beam Web (Sec. J4.2)

Length of the Coped Section

h0 d- dct dcb h0 400- 19.1 19.1 h0 361.9 mm

Net Area Subject to Shear

1 1
Anv h0 -n dh t Anv 361.9-4 33.3 8.6 Anv 19.1 cm²
16 16
Shear Rupture Strength (Eq. J4-4)

ϕRn ϕ0.6Fu Anv ϕRn 0.75*0.6*360*19.1 ϕRn 309.569 kN

Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.316
ϕRn 309.569
<D/C> Ratio is less than 1, Design is
OK

8-Block Shear Rupture of the Beam Web (Spec. J4.3)

Gross Area Subject to Shear

d-l 400-287.6
Lev Lev Lev 56.2 mm
2 2
Agv n-1 s Lev t Agv 4-1 75 56.2 8.6 Agv 24.2 cm²

Net Area Subject to Shear

1 1
Anv n-1 s Lev - n-d t
2 h 16
1
Anv 4-1 75 56.2- 4- 33.3
2 Anv 13.7 cm²
1
8.6
16
Net Area Subject to Tension

Leh a-g Leh 50-12.5 Leh 37.5 mm

1 1 1 1 1 1
Ant Leh - - dh t Ant 37.5- - 33.3 8.6 Ant 1.2 cm²
4 2 16 4 2 16
Available Strength (Eq. J4-5)
ϕRn ϕ Fu Ant min 0.6Fy Agv , 0.6Fu Anv
ϕRn
0.75 360*1.2
min 0.6*235*24.2,0.6*360*13.7
ϕRn 253.2489 kN

Page 5 of 8 12/12/2023
ETABS 21.2.0

Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.386
ϕRn 253.2489
<D/C> Ratio is less than 1, Design is
OK

9-Flexural Strength of Beam (Spec. F13)

Beam Elastic Section Modulus

b bf -tw b 180-8.6 b 171.4 mm

h d-2tf h 400-2*13.5 h 373 mm

bf d2 bh3 180*4002 171.4*3733

Sxx - Sxx - Sxx 1093.8 cm³
6 6d 6 6*400
Beam Flexural Strength (Spec. Eq. F13-
1)
ϕMn ϕFu Sx ϕMn 0.9*360*1093.8 ϕMn 354.3989 kN-m
Mu 63.424
D/C Ratio D/C Ratio D/C Ratio 0.179
ϕMn 354.3989
<D/C> Ratio is less than 1, Design is
OK

10-Weld Strength (Spec. J2.4)

Available Strength (Manual Eq. 8-1)

D √2
ϕRn ϕ0.6Fexx L
16 2
100 √2
ϕRn 0.75*0.6*482.63* * *287.6*2 ϕRn 552.0946 kN
16 2
Ru 97.8522
D/C Ratio D/C Ratio D/C Ratio 0.177
ϕRn 552.0946
<D/C> Ratio is less than 1, Design is
OK

11-Strength of Column at Weld (Manual Part 9)

Required Thickness (Manual Eq. 9-2)

D √2
0.60 Fexx
tmin 16 2
0.6 Fu

100 √2
0.60*482.63* * tmin 5.9 mm
tmin 16 2
0.6*360
tmin 5.92488
D/C Ratio D/C Ratio D/C Ratio 0.312
tw 19
<D/C> Ratio is less than 1, Design is
OK

Page 6 of 8 12/12/2023
ETABS 21.2.0

12-Column Flange Local Bending (Spec. J10.1)

Developed Tension-Compression Pair

Force due to Mu
Mu 63.424
Ru Ru Ru 164.0982 kN
d-tf 400-13.5
Available Strength (Spec. Eq. J10-1)

ϕRn ϕ6.25tf 2 Fy

ϕRn 0.9*6.25*192 *235 ϕRn 477.1969 kN

Ru 164.0982
D/C Ratio D/C Ratio D/C Ratio 0.344
ϕRn 477.1969
Stiffeners are not required in the
column flange to resist the beam's
tensile flange force

13-Column Web Local Yielding (Spec. J10.2)

Distance from Outer Face of the Flange

to the Web Toe of the Fillet
k tf rw k 19 0 k 19 mm

Available Strength (Spec. Eq. J10-2)

ϕRn ϕ 5K lb Fy tw

ϕRn 1 5*19 13.5 235*11 ϕRn 280.4725 kN

Ru 164.0982
D/C Ratio D/C Ratio D/C Ratio 0.585
ϕRn 280.4725
Stiffeners are not required in the
column web to resist the beam's
tensile flange force

14-Column Web Local Crippling (Spec. J10.3)

Available Strength (Spec. Eq. J10-4)

ld tw Fy tf
ϕRn ϕ135tw 2 1 3 tf
d tw
ϕRn 0.75*135*112 1
13.5 11 235*19
3 19
400 11
ϕRn 686.11 kN
Ru 164.0982
D/C Ratio D/C Ratio D/C Ratio 0.239
ϕRn 686.11
Stiffeners are not required in the
column web to resist the beam's
compressive flange force

Page 7 of 8 12/12/2023
ETABS 21.2.0

15-Web Panel-Zone Shear (Spec. J10.6)

Axial Yield Strength of the Column

Py Fy A Py 235*159 Py 3736.5 kN

Axial Demand for Column

Pu=297.5602 kN
Available Strength (Spec. Eq. J10-9)

<Pu> <≤> 0.4<Py>

ϕRn ϕ0.6Fy dtw ϕRn 0.9*0.6*235*390*11 ϕRn 544.401 kN
Ru 164.0982
D/C Ratio D/C Ratio D/C Ratio 0.301
ϕRn 544.401
Stiffeners not required to resist the
panel zone web shear

Page 8 of 8 12/12/2023