0% found this document useful (0 votes)
156 views53 pages

Example Logsrl TP Digital Repeater 20230816 Rev0

This technical proposal summarizes a repeater system installation at Logisteed Malaysia Sdn. Bhd. to improve 4G indoor signal coverage. Based on a site survey, a Digital Repeater operating at 1800MHz is recommended, with a donor antenna on the rooftop and a service antenna in the mezzanine floor office area. Pre-installation walktests show weak 4G signals in the mezzanine floor that need improvement. The proposal details the donor and repeater specifications, coverage areas, site maps and contact details.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
156 views53 pages

Example Logsrl TP Digital Repeater 20230816 Rev0

This technical proposal summarizes a repeater system installation at Logisteed Malaysia Sdn. Bhd. to improve 4G indoor signal coverage. Based on a site survey, a Digital Repeater operating at 1800MHz is recommended, with a donor antenna on the rooftop and a service antenna in the mezzanine floor office area. Pre-installation walktests show weak 4G signals in the mezzanine floor that need improvement. The proposal details the donor and repeater specifications, coverage areas, site maps and contact details.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 53

TECHNICAL PROPOSAL

REPEATER SYSTEM
SITE NAME: LOGISTEED MALAYSIA SDN. BHD.
BANDAR BARU BANGI, SELANGOR
LRD: LOGSRL
DOCUMENT REVISION HISTORY
DATE REVISE DESCRIPTION REVISION
16/8/2023 Make submeter, subdB, and repeater in line with cable tray 1

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 2 of 38


SITE VIEW: LOGISTEED MALAYSIA SDN. BHD.

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 3 of 38


SITE MAP

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 4 of 38


INTRODUCTION
This documentation is prepared for Maxis for one of the locations in Central Region of Malaysia, LOGISTEED MALAYSIA SDN. BHD. to
improve their existing 4G indoor signal coverage. Based on the network optimizations and the survey done, Digital Repeater 1800MHz
(High Power) are required at this location located at LOGISTEED MALAYSIA SDN. BHD. to enhance 4G indoor signals for the building.

The Scope of Work covering for this project is as follow: -

❖ Site Survey at LOGISTEED MALAYSIA SDN. BHD.:


• Propose for 4G donor antenna.
• Propose for repeater location with power source.
o All power work will be done by C&C Universal Engineering.
• Propose all RF components required.
• Propose all structure cabling including RF and power.
• Propose all required CME works.
− Hacking works: 2 pcs

The details and descriptions of the Scope are mentions in this document.

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 5 of 38


CONTACT INFORMATION
CUSTOMER NAME MAXIS BROADBAND SDN. BHD

Customer Contact PM: Mr. Rajandra Suppiah Contact No: 012-4000120

CONTRACTOR NAME C&C UNIVERSAL ENGINEERING SDN BHD

Survey Engineer: Amin Contact No: +6011-1420 6091

Contractor Contact Survey Engineer: Syazani Contact No: +6019-515 0875

BUILDINGS NAME LOGISTEED MALAYSIA SDN. BHD.

BM Contact Mr. Hamdan Contact No: +6017-694 6544

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 6 of 38


SURVEY INFORMATION
SURVEY DATE 09/08/2023 SURVEYOR C&C Universal Engineering (M) Sdn Bhd

SITE LRD LOGSRL

SITE ADDRESS 3, Jalan 6c/12, Seksyen 16, 43650 Bandar Baru Bangi, Selangor

GPS Longitude: 101.7612324999376° Latitude: 2.9479685844244807°

CELLULAR SYSTEM GSM (2G) WCDMA (3G) LTE (1800)

REPEATER TYPE DS100-40T-7DCS

2G/4G Co-donor antenna YES NO

2G/4G Co-serving antenna YES NO


COMBINATION OF 2G AND 4G
SYSTEM
Quadplexer on donor YES NO

Quadplexer on serving antenna YES NO

DONOR ANTENNA LOCATION Rooftop

REPEATER LOCATION Office Mezzanine Floor

SERVICE ANTENNA LOCATION Office (Mezzanine Floor)

POWER SUPPLY Tap from BM ACDB at Electrical Room Mezzanine Floor

GROUNDING BM earthing copper tape

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 7 of 38


BUILDING INFORMATION & COVERAGE DEFINITION

TYPE: INDOOR

Covered Area per floor


LEVEL LOT TYPE Area per floor(m2)
(m2)

First Floor WAREHOUSE Not covered Not covered

Mezzanine Floor OFFICE 3519 2265


COVERAGE AREA
Ground Floor STORAGE AREA Not covered Not covered

TOTAL AREA(m2) 3519 COVERED AREA(m2) 2265

REMARK

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 8 of 38


LTE DONOR INFORMATION (L1800)
Donor Cell Neighbour Cell
Donor Cell Name WATAML Status PCI RSRQ RSRP
Cell ID 53986818 PC 196 -11.5 dB -71.3 dBm
eNode B ID 210886/ 2 DC 28 -13.9 dB -76.8 dBm

EARFCN 1300 N/A N/A N/A N/A


PCI 196 N/A N/A N/A N/A
LTE (1800) Serving RSRP -71.0 dBm Donor Cell (Throughput)
Serving RSRQ -11.2 dB
Serving SNR 4.9 dB
Carrier RSSI -39.9 dBm
Donor Ant. (Azimuth) 322.98°
Donor Ant. (Height) 20m
Donor Outdoor (Height) TBC by Maxis

Remarks

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 9 of 38


LTE DONOR SELECTION SUMMARY TABLE
Info L1800 L2100 L2600
Donor Site WATAML BANGMI WATAME

RSRP -71.0 dBm -77.6 dBm -78.1 dBm


RSRQ -11.2 dB -10.6 dB -11.8 dB
RSSI -39.9 dBm -48.3 dBm -49.4 dBm
SNR 4.9 dB 3.8 dB 1.6 dB
PCI 196 82 136
DL (Mbps) 24.1 - 29.6 32.3 - 52.1 12.0 - 16.3

UL (Mbps) 29.8 - 39.5 27.3 - 30.7 39.5 – 53.5


LOS to Repeater
NO NO NO
Donor Site

Summary at
Donor Antenna

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 10 of 38


37
DONOR SIGNAL FINDINGS AND COMPARISON SUMMARY

- Based on the findings above, the preferred 4G solution to be used is L1800 due to the below:
o L1800 has the best RSRP, RSSI and SNR values at donor antenna location compared to other LTE bands.
o The most dominant 4G band at the received location at site is L1800.
- The final preferred repeater configuration, to accommodate 4G will be L1800.

CONCLUSION

- As a conclusion, the preferred repeater configuration based on the priority’s selection will be (L1800).

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 11 of 38


37
4G PRE-WALKTEST RESULT

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 12 of 38


37
4G UNLOCKED PRE-WALKTEST MEZZANINE FLOOR (RSRP)

Mezzanine office have


Cel-fi

sa

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 13 of 38


37
4G UNLOCKED PRE-WALKTEST MEZZANINE FLOOR (RSRQ)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 14 of 38


37
4G UNLOCKED PRE-WALKTEST MEZZANINE FLOOR (PCI)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 15 of 38


37
4G UNLOCKED PRE-WALKTEST MEZZANINE FLOOR (CH)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 16 of 38


37
4G L1800 PRE-WALKTEST MEZZANINE FLOOR (RSRP)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 17 of 38


37
4G L1800 PRE-WALKTEST MEZZANINE FLOOR (RSRQ)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 18 of 38


37
4G L1800 PRE-WALKTEST MEZZANINE FLOOR (PCI)

Mezzanine office have


Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 19 of 38


37
4G L1800 PRE-WALKTEST MEZZANINE FLOOR (CH)

Mezzanine office
have Cel-fi

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 20 of 38


37
PROPOSED EQUIPMENT LOCATION: DONOR ANTENNA LOCATION

4G (L1800) Donor Information:


DONOR CELL NAME: WATAML
ANT: HPTODL-0727-11NF1
PCI: 196
RSRP: -71.0 dBm
RSRQ: -11.2 dB
RSSI: -39.9 dBm
Cell ID: 53986818
Azimuth: 322.98°
Proposed Yagi antenna location
mounted on 0.5m boom c/w aerial
TV bracket and lightning spike

Mounting boom base

REMARK: Aerial TV Bracket used


to mount boom
Inside view of the roof to mount
donor

Proposed donor antenna location at rooftop

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 21 of 38


37
TOP VIEW PROPOSED EQUIPMENT LOCATION: DONOR LOCATION

Propose donor antenna location


at rooftop

Top view proposed donor antenna location at rooftop

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 22 of 38


37
PROPOSED EQUIPMENT LOCATION: REPEATER LOCATION
Proposed 100mm green
epoxy cable tray (L: 15m)

Proposed 25mm PVC pipe


(L: 6m)

Propose Maxis single phase


sub-meter location

Propose Maxis sub-DB

Proposed Maxis SSO


location (Qty: 2pcs)
Submeter Height: 1.8m

Proposed Maxis 4G
repeater location

Proposed Maxis busbar


location

Proposed Maxis Repeater location inside Electrical room at Mezzanine floor

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 23 of 38


37
TOP VIEW PROPOSED EQUIPMENT LOCATION: REPEATER LOCATION

Propose repeater location inside


Electrical room at Mezzanine
floor.

OFFICE MEZZANINE FLOOR

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 24 of 38


37
PROPOSE POWER ROUTING LOCATION FOR REPEATER

Propose power cable route from


Electrical room ACDB to the
proposed Maxis SSO (L: 10m)

Propose to add 32A breaker

Proposed power cable routing from BM ACDB at Electrical room

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 25 of 38


37
Proposed 100mm green Proposed 25mm PVC pipe
epoxy cable tray (L: 15m) (L: 6m)

Proposed power cable inside


Propose Maxis single phase 25mm PVC pipe (L: 15m)
sub-meter location

Propose Maxis sub-DB

Proposed Maxis SSO


location (Qty: 2pcs)

Proposed Maxis 4G
repeater location

Proposed Maxis busbar


location

Proposed Maxis Repeater location inside Electrical room at Mezzanine floor

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 26 of 38


37
PROPOSED GROUNDING ROUTE FOR DONOR
4G (L1800) Donor Information:
DONOR CELL NAME: WATAML
ANT: HPTODL-0727-11NF1
PCI: 196
RSRP: -71.0 dBm
RSRQ: -11.2 dB
RSSI: -39.9 dBm
Cell ID: 53986818
Azimuth: 322.98°

Proposed grounding cable route from


existing BM copper tape to proposed donor
antenna location (L: 2m)

Proposed grounding tapping route location for donor at Rooftop

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 27 of 38


37
PROPOSED FEEDER AND GROUNDING CABLE ROUTE FROM DONOR TO REPEATER

4G (L1800) Donor Information:


DONOR CELL NAME: WATAML
ANT: HPTODL-0727-11NF1
PCI: 196
RSRP: -71.0 dBm
RSRQ: -11.2 dB
RSSI: -39.9 dBm
Cell ID: 53986818
Azimuth: 322.98°
Proposed grounding cable route from
existing BM copper tape to proposed maxis
busbar at repeater location (L: 108m)

Proposed 1/2" feeder cable from donor


antenna to proposed repeater location
inside 25mm PVC pipe (L: 30m)

Proposed feeder and grounding route location for donor at Rooftop

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 28 of 38


37
Propose 1/2” feeder cable and grounding
cable from propose donor antenna location to
proposed repeater location inside 25mm PVC
conduit (L: 30m)

Request BM to clear this area for


Genie Lift during installation.

Existing 20mm space


for 1/2" feeder cable
and grounding cable

Proposed feeder and grounding cable route at Warehouse Level 1

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 29 of 38


37
Propose 7/8” feeder cable and grounding
cable from propose donor antenna location to
proposed repeater location inside 25mm PVC
conduit (L: 78m)

Propose to hack and make good

Proposed feeder and grounding cable route at Mezzanine floor

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 30 of 38


37
Propose 7/8” feeder cable and grounding
Proposed 100mm green cable from proposed donor antenna location to
epoxy cable tray (L: 15m) proposed repeater location inside 25mm PVC
conduit (L: 78m)

Proposed Maxis
Repeater

Proposed Maxis
busbar

Proposed feeder cable and grounding cable route inside Electrical room at Mezzanine floor

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 31 of 38


37
TOP VIEW PROPOSED PROPOSED FEEDER TO REPEATER LOCATION

Propose 1/2” feeder cable and


grounding cable from propose donor
to proposed repeater location (L: 30m)

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 32 of 38


37
TOP VIEW PROPOSED PROPOSED FEEDER TO REPEATER LOCATION

Proposed 7/8” feeder cable and


grounding cable from proposed donor
antenna location to proposed repeater
location (L: 78m)

OFFICE MEZZANINE FLOOR

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 33 of 38


37
PROPOSED SERVICE ANTENNA LOCATION

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 34 of 38


37
From first floor

Proposed omni antenna


inside meeting room 2
78.0m

1m Jumper

LOGSRL 3, Jalan 6c/12, Seksyen 16, Nur Amin


43650 Bandar Baru Bangi,
Selangor.
C&C Universal Engineering
From rooftop
To mezzanine

LOGSRL 3, Jalan 6c/12, Seksyen 16, Nur Amin


43650 Bandar Baru Bangi,
Selangor.
C&C Universal Engineering
30m
To first floor

LOGSRL 3, Jalan 6c/12, Seksyen 16, Nur Amin


43650 Bandar Baru Bangi,
Selangor.
C&C Universal Engineering
PROPOSED SCHEMATIC DIAGRAM

LRD: LOGSRL Version: 0 Date: 14-August-2023 Page 35 of 38


37
Pictograms legend

2-Way Splitter

6dB Coupler

Yagi Antenna
ROOFTOP

Omni Antenna
4G L1800 Yagi Antenna
MEZZANINE Repeater
9.57

14.89 m
A1-MZ-2

S2-MZ-1
30 m 11.39 Cables legend
Feeder 1/2
[1.00 m] [1.00 m] A1-MZ-4
C6-MZ-1 Feeder 7/8
1m Jumper
FIRST 28.09 m
FLOOR 7.53 m 13.38

S2-MZ-2 A1-MZ-3 Revision history


6.85 m

13.18 m 13.42

A1-MZ-1

78 m

Project name

4G (L1800) Donor Information: LOGSRL


DONOR CELL NAME: WATAML
Address
ANT: HPTODL-0727-11NF1
PCI: 196 3, Jalan 6c/12, Seksyen 16,
43650 Bandar Baru Bangi, Selangor
RSRP: -71.0 dBm
Designer name
RSRQ: -11.2 dB
RSSI: -39.9 dBm Nur Amin

Cell ID: 53986818


Azimuth: 322.6°
Design plan

C&C Universal Engineering


SUMMARY OF MATERIAL
NO DESCRIPTION UOM Quantity

1. REPEATER L1800 (DS100-40T-7DCS) pcs 1

2. Yagi Antenna (HPTODL-0727-11NF1) pcs 1

3. Omni Antenna pcs 4

4. 1/2” Feeder Cable mtr 45

5. 7/8” Feeder Cable mtr 135

6. 1/2” Feeder Clamp pcs 15

7. 1m Jumper N(M)-N(F) pcs 6

8. 1m Jumper N(M)-N(M) pcs 2

9. 1/2” N(M) Connector pcs 5

10. 1/2" N(F) Connector pcs 1

11. 7/8” N(M) Connector pcs 8

12. 2-Way Splitter pcs 2

13. Attenuator 20db pcs 1

14. 6dB Coupler pcs 1

15. 100mm Green Epoxy cable tray mtr 15

16. 16mm Grounding Cable mtr 115

17. Power Cable mtr 15

18. 25mm Flexible Conduit mtr 16

19. 25mm White PVC Pipe mtr 129

LRD: LOGSRL Version: 0 Date: 08-August-2023 Page 38 of 38


20. 0.5m boom pcs 1

21. 2-Gang SSO pcs 1

22. Aerial TV bracket pcs 1

23. 32A MCB pcs 2

24. 40A ELCB pcs 1

25. Submeter Single Phase pcs 1

26. Sub-DB Box pcs 1

27. Busbar pcs 1

28. Black Tape pcs 1

29. Scotch Tape pcs 1

30. 12” PVC Cable Tie pcs 150

31. 12” Steel Cable Tie pcs 10

LRD: LOGSRL Version: 0 Date: 08-August-2023 Page 38 of 38


Address: 5th FL, E BLDG, Sogood Science Park, Hangkong Road, Xixiang,
Bao'an,Shenzhen, China 518102, Phone/Fax: +086-0755-29921615
Product Data Sheet Email: [email protected]
Website: www.huaptec.com
Product DIGITAL REPEATER
Model No DS100-40T-7DCS

Key Features
• MGC and AGC function
• Independent uplink and downlink gain control and on/off for each sub band
• Each sub band is movable anywhere with in respective band
• Each sub band tunable with Minimum BW of 0.2MHz up to 10MHz.
• The distance between two sub bands could be as much as respective band's BW
• No Hurdles for Network Migration without changing any Hardware
• Designed for indoor or outdoor installation
• High integration with lesser cable Interface
• Local Access: Bluetooth vide through Phone APP or vide through USB or Ethernet
• Remote Access: Wi-Fi connection or vide through Ethernet, GPRS/3G/4G Data

RF Parameters
Bands Uplink Downlink
Frequency Range
DCS1800/LTE1800 1710MHz 1785MHz 1805MHz 1880MHz
Gain 85dB 90dB
Max Output Power 26±2dBm 40±2dBm
Band width DCS1800/LTE1800 3*20 0.2-20MHZ tunable and movable
MGC (Step Attenuation) ≥ 31 dB / 1 dB step
Automatic Gain Control ≥ 51 dB
Gain Flatness Typical≤ 3~6 dB
Noise Figure Typical≤ 5~6 dB
Group Delay ≤ 7.5 µs
VSWR ≤2
Frequency Stability ≤0.01ppm
±400KHz ≤65dB ≤75dB
Out of Band Rejection ±600KHz ≤55dB ≤65dB
(GSM/DCS) ±1MHz ≤50dB ≤60dB
±5MHz ≤40dB ≤50dB
≥200kHz offset ≤75dB ≤85dB
Out of Band Rejection ≥1MHz offset ≤60dB ≤75dB
(LTE) ≥5MHz offset ≤60dB ≤75dB
≥10MHz offset ≤50dB ≤70dB
Output intermodulation 9KHz~1GHz ≤-20dBm ≤-5dBm
(GSM/DCS) 1GHz-12.75GHz ≤-20dBm ≤-5dBm
9KHz~1GHz ≤-36dBm ≤-36dBm
Spurious Emission 1GHz-12.75GHz ≤-30dBm ≤-30dBm
ICS / ICE Performance ≥15dB ≥15dB
Maximum Input Power ≤-10dBm ≤-10dBm
Electrical Parameters
Impedance 50 ohm
Power Supply Input AC100~240 V, 50~60 Hz
Power Consumption ≤ 160 W

Huaptec Telecom GmbH Huaptec US Inc. Huaptec Telecom India Private Limited
Phone: (44)20 3239 5808 Phone: (972) 870-5666 Address: No 57/2, Ground Floor, 8th Main,2nd Stage J.C.
Address: Benno-Strauß-Street 7, 90763 Fürth, Germany Address: 6210 N Belt Line Rd., Ste. 110, Irving, TX 75063 Industrial Estate, Yelachenahalli, Kanakapura Main Road
Email: [email protected] Email: [email protected] Bengaluru, Phone: +91-80-45973000 & 49572000, Email:
[email protected]
Address: 5th FL, E BLDG, Sogood Science Park, Hangkong Road, Xixiang,
Bao'an,Shenzhen, China 518102, Phone/Fax: +086-0755-29921615
Product Data Sheet Email: [email protected]
Website: www.huaptec.com
Product DIGITAL REPEATER
Model No DS100-40T-7DCS

Mechanical Parameters
I/O Port N-Female
Dimensions 450*316*181 mm
Weight ≤25 kg
Environmental Parameters
Operating Temperature (-)25 ºC~+55 ºC
Storage Temperature (-)40°C to +85°C
Relative Humidity 5% - 95%
Environment Conditions IP65
Software
Local Monitoring Bluetooth vide through Phone APP or PC via Ethernet Port
Remote Monitoring Wi-Fi connection or vide through Ethernet, GPRS/3G/4G Data
Controlled Parameters Gain, Frequency, Repeater ON/OFF, Alarm Message, etc.
Monitoring Parameters Gain, Frequency, Repeater ON/OFF, Alarm Message, etc.
Alarm Items ISO Alarm , ALC Alarm, etc.

Installation Example

Huaptec Telecom GmbH Huaptec US Inc. Huaptec Telecom India Private Limited
Phone: (44)20 3239 5808 Phone: (972) 870-5666 Address: No 57/2, Ground Floor, 8th Main,2nd Stage J.C.
Address: Benno-Strauß-Street 7, 90763 Fürth, Germany Address: 6210 N Belt Line Rd., Ste. 110, Irving, TX 75063 Industrial Estate, Yelachenahalli, Kanakapura Main Road
Email: [email protected] Email: [email protected] Bengaluru, Phone: +91-80-45973000 & 49572000, Email:
[email protected]
Product Specifications

Product: 698-2700MHz N Splitter

CHARACTERISTICS

Product number HPTPD2-0727-PNFO HPTPD3-0727-PNFO HPTPD4-0727-PNFO


Configuration 1:2 1:3 1:4
Insertion loss 3.0dB 4.8dB 6.0dB
Ripple ≤0.3 dB ≤0.4dB ≤0.5 dB

VSWR 1.25 1.25 1.25


Weight ≤320 g ≤360 g ≤450 g
Frequency range 698 - 2700 MHz

PIM (3rd order) 150dBc @ 2 x 43dBm CW

Power capacity ≤300 W


Impedance 50 Ω
Operating temperature -25°C to +75 °C
Storage temperature -40°C to +85 °C
Relative humidity 0~95%
Applications Indoor or Outdoor
Ingress protection IP65
RF Connector N-Female
Schematic diagram:

2-way Splitter 3-way Splitter 4-way Splitter

P2 P2 P2
P1 P3
P1 P3 P1
P3 P4
P4 P5

Add.: 5th FL,E BLDG,Sogood Science Park,Hangkong Road, Xixiang,Bao'an,Shenzhen,China 518102


E-mail:[email protected] Web site:www.huaptec.com
Product Specifications

Product: Coupler N 698 - 2700 MHz, 5,6,7,8,10,13,15,20,30dB

CHARACTERISTICS

HPTC5- HPTC6- HPTC7- HPTC8- HPTC10 HPTC13 HPTC15 HPTC20 HPTC30


Product number 0727-
0727- 0727- 0727- -0727- -0727- -0727- -0727- -0727-
PNFO PNFO PNFO PNFO PNFO PNFO PNFO PNFO PNFO

Specifications 5.0 dB 6.0 dB 7.0 dB 8.0 dB 10dB 13dB 15dB 20dB 30 dB

Attenuation ±1 ±1 ±1 ±1 ±1 ±1.2 ±1.2 ±1.2 ±1.5

sertion loss ≤ 2.15dB ≤ 1.7dB ≤ 1.4dB ≤ 1.2dB ≤ 0.8dB ≤ 0.6dB 0.5 0.5 0.3

Isolation ≥25 ≥26 ≥27 ≥28 ≥30 ≥33 ≥35 ≥40 ≥45

Weight 0.25kg

Dimension ≈159.5*63.5*17.5mm

Frequency range 698 - 2700 MHz

PIM (3rd order) -150dBc @ 2 x 43dBm CW

Power capacity ≤300 W

VSWR ≤1.25

Impedance 50 Ω

Operating -25°C to +75 °C


temperature
-40°C to +85 °C
Storage temperature

Relative humidity 0~95%

IP65
Ingress protection

RF Connector N-Female

Note: Picture is only for reference, goods in kind prevail

Add.: 3th FL,E BLDG,Sogood Science Park,Hangkong Road, Xixiang,Bao'an,Shenzhen,China 518102


E-mail:[email protected] Web site:www.huaptec.com
FLEXIBLE RF CABLE
HCAAY-50-12 (1/2"L)

CONSTRUCTION MATERIALS
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Corrugated Aluminum Tube
Jacket Black PE

PHYSICAL DIMENSIONS
Inner Conductor Diameter 4.80 mm
Dielectric Diameter 12.30 mm
Outer Conductor Diameter 13.90 mm
Diameter Over Jacket 15.70 mm

MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATION


Minimum Bending Radius Capacitance 76.0 pF/m(23.2pF/ft)
Single Bending 50 mm Impedance 50±2 Ω
Repeated Bending 125 mm Velocity 86%
Minimum Number of Bends 15 RF Peak Voltage 1.60 kV
Tensile Strength 1000 N Peak Power Rating 36 kW
Cut-off Frequency 8.8 GHz
Shielding Effectiveness >10MHz >120 dB
Insulation Resistance 50000 MΩ•km
ENVIRONMENTAL SPECIFICATION
Storage Temperature -55 ℃ ~ +85 ℃ VSWR
Installation Temperature -40 ℃ ~ +60 ℃ 0.8~1.0 GHz ≤1.15
Operating Temperature -55 ℃ ~ +85 ℃ 1.7~2.7 GHz ≤1.15

PERFORMANCE
Frequency Attenuation Average
MHz dB/100 m dB/100 ft Power Rating (kW)
100 2.31 0.70 3.94
200 3.32 1.01 2.75
450 5.05 1.54 1.80
800 6.88 2.10 1.33
900 7.36 2.24 1.25
960 7.70 2.35 1.19
1000 7.79 2.37 1.18
1500 9.71 2.96 0.95
1800 10.70 3.26 0.86
2000 11.39 3.47 0.81
2100 11.70 3.57 0.79
2200 12.02 3.66 0.77
2400 12.55 3.83 0.75
2500 12.88 3.93 0.73
2600 13.20 4.02 0.71
3000 14.23 4.34 0.65

Standard Conditions :
For attenuation : VSWR 1.0 , cable temperature 20 ℃ (68 ℉ )
For average power : VSWR 1.0 , ambient temperature 40 ℃ (104 ℉ ) ,
Inner conductor temperature 100 ℃ (212 ℉ ) 。 No solar loading 。
Maximum attenuation value shall be 105% of the nominal attenuation value.

www.hengxin.com
FLEXIBLE RF CABLE
HCTAY-50-23 (7/8"AL)

CONSTRUCTION MATERIALS
Inner Conductor Smooth Copper Tube
Dielectric Physical Foam Polyethylene
Outer Conductor Corrugated Aluminum Tube
Jacket Black PE

PHYSICAL DIMENSIONS
Inner Conductor Diameter 9.30 mm
Dielectric Diameter 22.80 mm
Outer Conductor Diameter 25.40 mm
Diameter Over Jacket 27.80 mm

MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATION


Minimum Bending Radius Capacitance 74.0 pF/m(22.6 pF/ft)
Single Bending 120 mm Impedance 50±2 Ω
Repeated Bending 250 mm Velocity 88%
Minimum Number of Bends 15 RF Peak Voltage 3.00 kV
Tensile Strength 1450 N Peak Power Rating 80 kW
Insulation Resistance 5000 MΩ•km
Cut-off Frequency 5.10 GHz
Shielding Effectiveness >10MHz >120 dB
ENVIRONMENTAL SPECIFICATION
Storage Temperature -55 ℃ ~ +85 ℃ Frequency Band VSWR
Installation Temperature -40 ℃ ~ +60 ℃ 0.8~1.0 GHz ≤1.15
Operating Temperature -55 ℃ ~ +85 ℃ 1.7~2.7 GHz ≤1.15

PERFORMANCE
Frequency Attenuation Average
MHz dB/100 m dB/100 ft Power Rating (kW)
100 1.23 0.37 6.24
200 1.76 0.54 4.34
450 2.75 0.84 2.83
800 3.73 1.14 2.07
900 3.92 1.19 1.93
960 4.09 1.25 1.85
1000 4.16 1.27 1.83
1500 5.24 1.60 1.45
1800 5.85 1.78 1.28
2000 6.16 1.88 1.23
2100 6.35 1.94 1.19
2200 6.58 2.01 1.18
2500 7.00 2.13 1.05
2600 7.10 2.16 1.04
3000 7.54 2.30 0.98

Standard Conditions :
For attenuation : VSWR 1.0 , cable temperature 20 ℃ (68 ℉ )
For average power : VSWR 1.0 , ambient temperature 40 ℃ (104 ℉ ) ,
Inner conductor temperature 100 ℃ (212 ℉ ) 。 No solar loading 。
Maximum attenuation value shall be 105% of the nominal attenuation value.

www.hengxin.com
Product Specification
NM-1/2”L 01L

N Straight male Connector for 1/2"


Flexible RF Cable

HXQJ180518

Rev: A0

Material and Plating


Inner Conductor Pin Brass / Silver Plating
Inner Conductor Socket Tin Bronze / Silver Plating
Insulator PTFE/TPX
Body & Outer Conductor Brass / Trimetal Plating
Gasket Silicon Rubber
Nut Brass/Trimetal Plating

Electrical Specifications
Characteristics Impedance 50 Ohm
Frequency Range DC~11GHz
Insulation Resistance ≥5000MΩ
Dielectric Withstanding Voltage 2500V rms
Operating Voltage 1500V rms
Center contact resistance ≤1.0 mΩ
Outer contact resistance ≤0.25 mΩ
Insertion Loss @DC-2.7 GHz ≤0.10dB
Return Loss @DC-1000MHz ≥34dB
@1000-2200MHz ≥32dB
@2200-3000MHz ≥28dB
@3000-4000MHz ≥26dB
PIM3(2*43dBm) ≤-155dBc

Environmental & Mechanical Specifications


Durability (matings) ≥500 cycles
Mechanical Shock Test Method MIL-STD-202, Method 213, Test Condition D
Vibration Test Method MIL-STD-202, Meth. 204, Cond. A
Temperature Range -65°C to +85°C
RoHS Compliant
Sealing Class IP68 24hr, 1m, 20℃

Regulatory Compliance / Certification


ISO 9001:2015 Compliant

The facts and figures contained herein are carefully complied to the best of our knowledge, but they are
intended for general informational purposes only.
www.hengxin.com
Product Specification
NM-7/8”L 01L

N Straight male Connector for 7/8"


Flexible RF Cable

HXQJ180523

Rev: A0

Material and Plating


Inner Conductor Pin Brass / Silver Plating
Inner Conductor Socket Tin Bronze / Silver Plating
Insulator PTFE/TPX
Body & Outer Conductor Brass / Trimetal Plating
Gasket Silicon Rubber
Nut Brass/Trimetal Plating

Electrical Specifications
Characteristics Impedance 50 Ohm
Frequency Range DC~11GHz
Insulation Resistance ≥5000MΩ
Dielectric Withstanding Voltage 2500V rms
Operating Voltage 1500V rms
Center contact resistance ≤1.0 mΩ
Outer contact resistance ≤0.25 mΩ
Insertion Loss @DC-2.7 GHz ≤0.10dB
Return Loss @DC-1000MHz ≥34dB
@1000-2200MHz ≥32dB
@2200-3000MHz ≥28dB
@3000-4000MHz ≥26dB
PIM3(2*43dBm) ≤-155dBc

Environmental & Mechanical Specifications


Durability (matings) ≥500 cycles
Mechanical Shock Test Method MIL-STD-202, Method 213, Test Condition D
Vibration Test Method MIL-STD-202, Meth. 204, Cond. A
Temperature Range -65°C to +85°C
RoHS Compliant
Sealing Class IP68 24hr, 1m, 20℃

Regulatory Compliance / Certification


ISO 9001:2015 Compliant

The facts and figures contained herein are carefully complied to the best of our knowledge, but they are
intended for general informational purposes only.
www.hengxin.com
Product Specification
NM-NM HCF1/2 Lm HXQJ180513 Rev: A0

1/2" Super Flexible Cable Assembly


N Male To N Male

Product Description
Jumper Length Lm
Cable Type HRCAY-50-9(1/2" Super Flexible)
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Corrugated Copper Tube
Jacket Black PE
Connector Type N type male N type male
Inner Conductor Pin Brass/Silver Plating Brass/Silver Plating
Body&Outer Conductor Brass/Trimetal Plating Brass/Trimetal Plating
Insulator PTFE PTFE
Gasket Silicon Rubber Silicon Rubber
Nut Brass/Nickel Plating Brass/Nickel Plating

Electrical Specifications
Characteristics Impedance 50 Ohm
Frequency Range DC~7.5 GHz
Insulation Resistance ≥5000MΩ
Dielectric Withstanding Voltage 2500V rms (DC)
Operating Voltage 1500V
Inertion Loss @DC~2.7GHz ≤0.215*L+0.15dB
Return Loss @960MHz ≥ 34dB
@1800MHz ≥ 32dB
@2100MHz ≥ 30dB
@2600MHz ≥ 28dB
PIM3 @1800MHz(2*43dBm) ≤-155dBc

Environmental & Mechanical Specifications


Cable Tensile resistance ≥500N
Torque Proof (Nut) NM:1.73N.m
Storage Temperature -45°C to +65°C
Operating temperature -45°C to +85°C
Water Proof level IP68 24hr, 1m, 20℃
RoHS Compliant

Regulatory Compliance / Certification


ISO 9001:2015 Compliant

The facts and figures contained herein are carefully complied to the best of our knowledge, but they are intended for
general informational purposes only.
www.hengxin.com
Product Specification
NM-NF HCF1/2 Lm HXQJ180514 Rev: A0

1/2" Super Flexible Cable Assembly


N Male To N Female

Product Description
Jumper Length Lm
Cable Type HRCAY-50-9(1/2" Super Flexible)
Inner Conductor Copper-Clad Aluminum Wire
Dielectric Physical Foam Polyethylene
Outer Conductor Corrugated Copper Tube
Jacket Black PE
Connector Type N type male N type female
Inner Conductor Pin Brass/Silver Plating Tin-bronze/Silver Plating
Body&Outer Conductor Brass/Trimetal Plating Brass/Trimetal Plating
Insulator PTFE PTFE
Gasket Silicon Rubber /
Nut Brass/Nickel Plating /

Electrical Specifications
Characteristics Impedance 50 Ohm
Frequency Range DC~7.5 GHz
Insulation Resistance ≥5000MΩ
Dielectric Withstanding Voltage 2500V rms (DC)
Operating Voltage 1500V
Inertion Loss @DC~2.7GHz ≤0.215*L+0.15dB
Return Loss @960MHz ≥ 34dB
@1800MHz ≥ 32dB
@2100MHz ≥ 30dB
@2600MHz ≥ 28dB
PIM3 @1800MHz(2*43dBm) ≤-155dBc

Environmental & Mechanical Specifications


Cable Tensile resistance ≥500N
Torque Proof (Nut) NM:1.73N.m
Storage Temperature -45°C to +65°C
Operating temperature -45°C to +85°C
Water Proof level IP68 24hr, 1m, 20℃
RoHS Compliant

Regulatory Compliance / Certification


ISO 9001:2015 Compliant

The facts and figures contained herein are carefully complied to the best of our knowledge, but they are intended for
general informational purposes only.
www.hengxin.com
Product Specifications

Product: Indoor Omni Directional Antenna


Part Number: HPTIOC-0727-05NF

CHARACTERISTICS

Frequency range 698~960/1710~2700MHz


VSWR ≤1.8/≤1.5
1710~2700
Gain 2 dBi /5dBi
Horizontal-3dB beam width 360°
Vertical-3dB beam width 85°/55°
Polarization Vertical
Impedance 50 Ω

PIM (3rd order) ≤-150 dBc @ 2 x 43dBm CW

Max input protection 50W


Mechanical Specifications
Lightning protection DC Ground
Radome material ABS
Radome color White
Dimension(D*H) Ø 186mm×86mm
Weight 0.25kg
Radiating element material Cu.Al
Working temperature -40°C to +60°C
Ingress protection IP52

Connector N-female*1 ,RG141, 30cm


Installation

Add.: 5th FL,E BLDG,Sogood Science Park,Hangkong Road, Xixiang,Bao'an,Shenzhen,China 518102


E-mail:[email protected] Web site:www.huaptec.com
Product Specifications

Product: 698-2700 bidirectional Antenna


Part Number: HPTODL-0627-11NF1

CHARACTERISTICS

Frequency range 698~960 1710~2700


Polarization Vertical Vertical
Gain 10dBi 11dBi
Horizontal-3dB beam width 65° 60°
Vertical-3dB beam width 50° 40°
Front-to-Back ratio ≥15dB ≥18dB
VSWR ≤1.8 ≤1.5

PIM (3rd order) ≤-140 dBc @ 2 x 33dBm CW

Impedance 50 Ω
Max input protection 50W
Mechanical Specifications
Lightning protection Direct Ground
Dimension 442×205×62mm(L×W×H)
Weight 1.2kg
Radiating element material Cu.Al
Diameter Of Installation φ40mm~φ70mm or Mounts on the roof or wall

Radome material ABS UV resistant

Radome color White


Max Wind Speed 140Km/h
Cable 30cm, RG58U
Working temperature -40°C to +65 °C
Ingress protection IP65
Connector N-Female or user specified
Installation

Add.: 5th FL,E BLDG,Sogood Science Park,Hangkong Road, Xixiang,Bao'an,Shenzhen,China 518102


E-mail:[email protected] Web site:www.huaptec.com

You might also like