INTERNATIONAL ISO

STANDARD 8995
CIE S 008/E

Second edition
2002-05-15

Lighting of indoor work places

Éclairage intérieur pour des lieux de travail

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

Reference number
ISO 8995:2002(E)
CIE S 008/E-2001

© ISO 2002
ISO 8995:2002(E)

PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E- mail [email protected]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

 ISO 8995:2002(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.

International Standard ISO 8995 was prepared as Standard CIE S 008/E by the International Commission on
Illumination, which has been recognized by the ISO Council as an international standardizing body. It was adopted
by ISO under a special procedure which requires approval by at least 75 % of the member bodies casting a vote,
and is published as a joint ISO/CIE edition.

The International Commission on Illumination (abbreviated as CIE from its French title) is an organization devoted
to international cooperation and exchange of information among its member countries on all matters relating to the
science and art of lighting.

Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
iTeh STANDARD PREVIEW
International Standard ISO 8995 was prepared jointly by CIE TC 3-21 and ISO/TC 159, Ergonomics, Subcommittee
(standards.iteh.ai)
SC 5, Ergonomics of the physical environment.

This second edition cancels and replaces the ISO first8995-1:2002

edition (ISO 8995:1989), of which it constitutes a technical
revision. https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

© ISO 2002 – All rights reserved iii

ISO 8995:2002(E)

(Blankpage)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

iv © ISO 2002 – All rights reserved

 ISO 8995:2002(E)
CIE S 008/E-2001

Standard

Lighting of Indoor Work Places

Eclairage intérieur pour des lieux de travail
iTeh STANDARD PREVIEW
Beleuchtung von Arbeitsplätzen in Innenräumen
(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

CIE Standards are copyrighted and shall not be reproduced in any form, entirely or partly, without
the explicit agreement of the CIE.

CIE Central Bureau, Vienna S 008/E

Kegelgasse 27, A-1030 Vienna, Austria
UDC: 628.972 Descriptor: Interior lighting

© ISO 2002 – All rights reserved v

ISO 8995:2002(E)
CIE S 008/E-2001

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

 CIE 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from CIE Central Bureau at the address below.
CIE Central Bureau
Kegelgasse 27
A-1030 Vienna
Austria
Tel.: +43 1 714 3187 0
Fax: +43 1 713 0838 18
e-mail: [email protected]
Web: www.cie.co.at/cie

II  CIE, 2001 - All rights reserved

vi © ISO 2002 – All rights reserved
 ISO 8995:2002(E)
CIE S 008/E-2001

Foreword
Standards produced by the Commission Internationale de l’Éclairage (CIE) are a concise
documentation of data defining aspects of light and lighting, for which international harmony
requires such unique definition. CIE Standards are therefore a primary source of
internationally accepted and agreed data, which can be taken, essentially unaltered, into
universal standard systems.
This International Standard was prepared jointly by CIE-TC 3-21 and ISO/TC 159/SC 5.
It replaces publication CIE 29.2-1986 and deals with Lighting Requirements for Indoor Work
Places.

Table of contents
FOREWORD ......................................................................................................................... III
INTRODUCTION .................................................................................................................... 1
1. SCOPE ............................................................................................................................... 1
2. NORMATIVE REFERENCES.............................................................................................. 1
3. DEFINITIONS ..................................................................................................................... 2
4. LIGHTING DESIGN CRITERIA ........................................................................................... 2
4.1 Luminous environment................................................................................................. 2
4.2 Luminance distribution ................................................................................................. 3
4.3 Illuminance................................................................................................................... 3
iTeh STANDARD PREVIEW
4.3.1 Recommended illuminances at the task area ....................................................... 3
(standards.iteh.ai)
4.3.2 Scale of illuminance. ............................................................................................ 4
4.3.3 Illuminances of immediate surroundings .............................................................. 4
4.3.4 Uniformity ............................................................................................................ 4
ISO 8995-1:2002
4.4 Glare............................................................................................................................ 5
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
4.4.1 Shielding against glare......................................................................................... 5
bc08671c4023/iso-8995-1-2002
4.4.2 Discomfort glare................................................................................................... 5
4.4.3 Veiling reflections and reflected glare ................................................................... 6
4.5 Directionality ................................................................................................................ 6
4.5.1 Modelling ............................................................................................................. 6
4.5.2 Directional lighting of visual tasks......................................................................... 6
4.6 Colour aspects ............................................................................................................. 6
4.6.1 Colour appearance............................................................................................... 7
4.6.2 Colour rendering .................................................................................................. 7
4.7 Daylight........................................................................................................................ 7
4.8 Maintenance ................................................................................................................ 8
4.9 Energy considerations.................................................................................................. 8
4.10 Lighting of workstations with visual display terminals VDT ......................................... 8
4.11 Flicker and stroboscopic effect................................................................................... 8
4.12 Emergency lighting..................................................................................................... 9
5. SCHEDULE OF LIGHTING REQUIREMENTS.................................................................... 9
6. VERIFICATION PROCEDURES ....................................................................................... 17
6.1 Illuminance................................................................................................................. 17
6.2 Unified glare rating..................................................................................................... 17
6.3 Colour rendering index (Ra)........................................................................................ 17
6.4 Colour appearance (Tcp)............................................................................................. 17
6.5 Maintenance .............................................................................................................. 17
6.6 Luminaire luminance.................................................................................................. 17
6.7 Tolerances in measurements ..................................................................................... 18

 CIE, 2001

 CIE, 2001 - All rights reserved III

© ISO 2002 – All rights reserved vii
ISO 8995:2002(E)
CIE S 008/E-2001

(Blankpage)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002

IV  CIE, 2001 - All rights reserved

viii © ISO 2002 – All rights reserved
 ISO 8995:2002(E)
CIE S 008/E-2001

LIGHTING OF INDOOR WORK PLACES

Introduction
Good lighting will create a visual environment that enables people to see, to move about
safely and to perform visual tasks efficiently, accurately and safely without causing undue
visual fatigue and discomfort. The illumination may be daylight, electric light or combination of
both.
Good lighting requires equal attention to the quantity and quality of the lighting. While
the provision of sufficient illuminance on the task is necessary, in many instances the visibility
depends on the way in which the light is delivered, the colour characteristics of the light
source and surfaces together with the level of glare from the system. In this standard
opportunity was taken to specify for various work places and task types not just the
illuminance but also the limiting discomfort glare and minimum colour rendering index of the
source. Parameters to create comfortable visual conditions are proposed in the body of this
standard. The recommended values are considered to represent a reasonable balance,
having regard to the requirements for safe, healthy and efficient work performance. The
values can be achieved with practical energy efficient solutions.
There are also visual ergonomic parameters such as perceptual ability and the
characteristics and attributes of the task, which determine the quality of the operator’s visual
skills, and hence performance levels. In some cases enhancement of these influencing factors
can improve performance without the need to raise illuminance. For example by improving the
contrast of the task attributes, enlarging the task by the use of up to date visual aids (glasses)
and by the provision of special lighting systems with local directional lighting capability.
iTeh STANDARD PREVIEW
1. Scope
(standards.iteh.ai)
This standard specifies lighting requirements for indoor work places and for people to perform
the visual tasks efficiently, in comfort and
ISOsafety throughout the whole work period.
8995-1:2002
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
This standard does not explain how lighting systems or techniques should be
designed to optimise solutions for bc08671c4023/iso-8995-1-2002
specific work places. These may be found in the relevant
CIE guides and reports.

2. Normative references
The following standards contain provisions which, through reference in this text, constitute
provisions of this International Standard. At the time of publication, the editions indicated were
valid. All standards are subject to revision, and parties to agreements based on this Standard
are encouraged to investigate the possibility of applying most recent editions of the standards
indicated below. Members of CIE, the International Electrotechnical Commission (IEC) and the
International Organization for Standardization (ISO) maintain registers of currently valid
international standards.
ISO 3864 Safety colours and safety signs
ISO 6309 Fire protection - safety signs
ISO 6385 Ergonomic principles in the design of work systems
ISO 9241 Parts 6/7/8 Ergonomic requirements for office work with visual display
terminals
CIE 13.3 - 1995 Method of measuring and specifying colour rendering of light
sources
CIE 16 - 1970 Daylight
CIE 17.4 - 1987 International lighting vocabulary 4th ed. – equivalent to IEC
50(845)
CIE 19.2 - 1981 An analytic model for describing the influence of lighting
parameters upon visual performance
CIE 40 - 1978 Calculations for interior lighting - basic method
CIE 58 - 1983 Lighting for sports halls

 CIE, 2001 - All rights reserved 1

© ISO 2002 – All rights reserved 1
ISO 8995:2002(E)
CIE S 008/E-2001

CIE 60 - 1984 Vision and the visual display unit work station
CIE 62 - 1984 Lighting for swimming pools
CIE 96 - 1992 Electric light sources. State of the art - 1991
CIE 97 - 1992 Maintenance of indoor electric lighting systems
CIE 103/5 - 1993 The economics of interior lighting maintenance
CIE 117 - 1995 Discomfort glare in interior lighting
CIE 129 - 1998 Guide for lighting of exterior work areas

3. Definitions
In general the terms used in this standard are defined in the CIE Lighting Vocabulary
(CIE 17.4 – 1987), but there are few more terms that are defined below:

3.1 visual task: The visual elements of the task to be carried out.
3.2 task area: The partial area in the work place in which the visual task is located and
carried out.
3.3 immediate surrounding: A zone of at least 0,5 m width surrounding the task area
within the field of vision.

3.4 maintained illuminance ( E m ): Value below which the average illuminance on the
specified surface should not fall.
3.5 unified glare rating (UGR): The CIE discomfort glare measure.
3.6 limiting unified glare rating (UGRL): The maximum allowable design UGR value for
the lighting installation.
iTeh STANDARD PREVIEW
3.7
(standards.iteh.ai)
Shielding angle: the angle measured from the horizontal, down to which the lamp(s)
is screened by the luminaire from direct view by an observer.
3.8 Working plane: the reference ISO surface defined as the plane at which work is usually
8995-1:2002
done. https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
bc08671c4023/iso-8995-1-2002
4. Lighting design criteria
4.1 Luminous environment

Good lighting practice for work places is more than just providing good task visibility. It is
essential that tasks are performed easily and in comfort. Thus the lighting must satisfy the
quantitative and qualitative aspects demanded by the environment. In general lighting is to
ensure:
- visual comfort, where the workers have a feeling of well-being,
- visual performance, where the workers are able to perform their visual tasks,
speedily and accurately even under difficult circumstances and during long
periods,
- visual safety, to see one’s way around and detect hazards.
To satisfy these, attention to all parameters contributing to the luminous environment
is required.
The main parameters are:
- luminance distribution,
- illuminance,
- glare,
- directionality of light,
- colour aspect of the light and surfaces,
- flicker,
- daylight,
- maintenance.

2  CIE, 2001 - All rights reserved

2 © ISO 2002 – All rights reserved
 ISO 8995:2002(E)
CIE S 008/E-2001

Design values for the quantifiable parameters of illuminance, discomfort glare and
colour rendering are given in clause 5 for the various activities.
Note: In addition to the lighting there are other visual ergonomic parameters which
influence operators visual performance, such as:
a) the intrinsic task properties (size, shape, position, colour and reflectance of
detail and background)
b) ophthalmic capacity of the operator (visual acuity, depth perception, colour
perception).
Attention to these factors can enhance visual performance without the need for
higher illuminance.

4.2 Luminance distribution

The luminance distribution in the field of view controls the adaptation level of the eyes, which
affects task visibility.
A well balanced adaptation luminance is needed to increase:
- visual acuity (sharpness of vision),
- contrast sensitivity (discrimination of relatively small luminance differences),
- efficiency of the ocular functions (such as accommodation, convergence, pupillary
contraction, eye movements, etc.).
Diverse luminance distribution in the field of view also affects visual comfort and
should be avoided:
-
-
iTeh STANDARD PREVIEW
too high luminances can give rise to glare.
too high luminance contrasts will cause visual fatigue due to continuous

-
(standards.iteh.ai)
readaptation of the eyes.
too low luminances and too low luminance contrasts result in a dull and non-
stimulating working environment. ISO 8995-1:2002
- attention should be given to adaptation in moving from zone to zone within a
https://standards.iteh.ai/catalog/standards/sist/a0fbda5e-47cc-4d79-bead-
building.
bc08671c4023/iso-8995-1-2002
The luminances of all surfaces are important and will be determined by the reflectance
of and the illuminance on the surfaces. The range of useful reflectances for the major interior
surfaces are:
- ceiling: 0,6 - 0,9
- walls: 0,3 - 0,8
- working planes: 0,2 - 0,6
- floor: 0,1 - 0,5
4.3 Illuminance

The illuminance and its distribution on the task areas and the surrounding area have a major
impact on how quickly, safely and comfortably a person perceives and carries out the visual
task. For spaces where the specific area is unknown the area where the task may occur is
taken as the task area.
All values of illuminances specified in this standard are maintained illuminances and
will provide for visual safety at work and visual performance needs.

4.3.1 Recommended illuminances at the task area

The values given in clause 5 are the maintained illuminances over the task area on the
reference surface which may be horizontal, vertical or inclined. The average illuminance for
each task shall not fall below the values given in clause 5 regardless of the age and condition
of the installation. The values are valid for normal visual conditions and take into account the
following factors:
- requirements for visual tasks,

 CIE, 2001 - All rights reserved 3

© ISO 2002 – All rights reserved 3