Ud18256b - Baseline - Ds k1t804 Series Fingerprint Access Control Terminal - User Manual - v1.0 - 20201207

Fingerprint Access Control Terminal
User Manual
Fingerprint Access Control Terminal User Manual
Legal Information
©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version of this Manual at the Hikvision website ( https://
www.hikvision.com/ ).
Please use this Manual with the guidance and assistance of professionals trained in supporting the
Product.
Trademarks
and other Hikvision's trademarks and logos are the properties of
Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH
ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION
BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY,
OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS,
AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE
SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT
INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF
PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.
YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE
DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR
i
PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED

TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN
RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
Data Protection
During the use of device, personal data will be collected, stored and processed. To protect data,
the development of Hikvision devices incorporates privacy by design principles. For example, for
device with facial recognition features, biometrics data is stored in your device with encryption
method; for fingerprint device, only fingerprint template will be saved, which is impossible to
reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with
the applicable data protection laws and regulations, including without limitation, conducting
security controls to safeguard personal data, such as, implementing reasonable administrative and
physical security controls, conduct periodic reviews and assessments of the effectiveness of your
security controls.
ii
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
Indicates a hazardous situation which, if not avoided, will or could
Danger result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could

Caution result in equipment damage, data loss, performance degradation, or
unexpected results.
Provides additional information to emphasize or supplement
Note
important points of the main text.
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
iv
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see:www.recyclethis.info
Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des
autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
v
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et
votre corps.
vi
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into Dangers and Cautions:
Dangers: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Dangers: Follow these safeguards to prevent Cautions: Follow these precautions to prevent
serious injury or death. potential injury or material damage.
Dangers
• All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
• Please use the power adapter, which is provided by normal company. The power consumption
cannot be less than the required value.
• Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
• Please make sure that the power has been disconnected before you wire, install or dismantle the
device.
• When the product is installed on wall or ceiling, the device shall be firmly fixed.
• If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
• Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it
can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close
securely, stop using the product and keep it away from children. If you think batteries might have
been swallowed or placed inside any part of the body, seek immediate medical attention.
• If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the device yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
Cautions
• This equipment is not suitable for use in locations where children are likely to be present.
• Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
vii
• Do not place the device in extremely hot (refer to the specification of the device for the detailed
operating temperature), cold, dusty or damp locations, and do not expose it to high
electromagnetic radiation.
• The device cover for indoor use shall be kept from rain and moisture.
• Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
• Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the
same time.
• Please use the provided glove when open up the device cover, avoid direct contact with the
device cover, because the acidic sweat of the fingers may erode the surface coating of the device
cover.
• Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do
not use alkaline detergents.
• Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportation without the
original wrapper may result in damage on the device and lead to additional costs.
• Improper use or replacement of the battery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used batteries according to the instructions provided by
the battery manufacturer.
• You can view the device License via the website: http://opensource.hikvision.com/Home/List?
id=46.
viii
Available Models
The fingerprint access control terminal contains the following models:
Product Name Model Description

Fingerprint Access Control DS-K1T804AF Supports fingerprint only.
Terminal
DS-K1T804AMF Supports presenting Mifare
card.
DS-K1T804AEF Supports presenting EM card.
Use only power supplies listed in the user instructions:
Model Manufacturer Standard
DSA-12PFT-12FUK 120100 Dee Van Enterprise Co., Ltd. BS
DSA-12PFT-12FAU 120100 Dee Van Enterprise Co., Ltd. AS
DSA-12PFT-12FIN 120100 Dee Van Enterprise Co., Ltd. IS
DSA-12PFT-12FUS 120100 Dee Van Enterprise Co., Ltd. IEC
DSA-12PFT-12 FBZ 120100 Dee Van Enterprise Co., Ltd. NBR
ADS-12B-12 12012E Shenzhen Honor Electronics IEC
Co., Ltd.
ADS-12B-12 12012E Shenzhen Honor Electronics NEMA
Co., Ltd.
ADS-12B-12 12012E Shenzhen Honor Electronics NBR
Co., Ltd.
ADS-12B-12 12012E Shenzhen Honor Electronics BS
Co., Ltd.
ix
Contents
Chapter 1 Overview .................................................................................................................... 1
Chapter 2 Features ..................................................................................................................... 2
Chapter 3 Appearance Description ............................................................................................. 3
Chapter 4 Device Wiring ............................................................................................................. 6
4.1 Terminal Description .............................................................................................................. 6
4.2 External Device Wiring ........................................................................................................... 9
4.3 Secure Door Control Unit Wiring ........................................................................................... 9
Chapter 5 Installation ............................................................................................................... 11
Chapter 6 Activation ................................................................................................................. 13
6.1 Activate via Device ............................................................................................................... 13
6.2 Activate via SADP ................................................................................................................. 13
6.3 Activate Device via Client Software ...................................................................................... 15
Chapter 7 Local Settings ............................................................................................................ 16
7.1 Select Language ................................................................................................................... 16
7.2 Add Administrator ................................................................................................................ 16
7.3 Local Login ........................................................................................................................... 19
7.4 Communication Settings ...................................................................................................... 19
7.4.1 Set Network ................................................................................................................ 20
7.4.2 Set Wi-Fi Parameters ................................................................................................... 20
7.4.3 Change Verification Code ............................................................................................ 21
7.4.4 Set EHome Parameters ............................................................................................... 21
7.4.5 Set Wiegand Parameters ............................................................................................. 23
7.4.6 Set RS-485 Parameters ................................................................................................ 23
7.5 Person Management ............................................................................................................ 24
7.5.1 Add Person .................................................................................................................. 24
7.5.2 Manage Person (Search/Edit/Delete) ......................................................................... 27
x
7.6 Access Control ...................................................................................................................... 28

7.6.1 Access Control Configuration Flow ............................................................................. 28
7.6.2 Set Access Control Parameters ................................................................................... 28
7.6.3 Set Holiday Group ....................................................................................................... 30
7.6.4 Set Week Plan ............................................................................................................. 33
7.6.5 Set Schedule Template ................................................................................................ 35
7.7 Attendance Status ................................................................................................................ 36
7.7.1 Set Auto Attendance ................................................................................................... 36
7.7.2 Set Manual Attendance .............................................................................................. 37
7.7.3 Set Manual and Auto Attendance ............................................................................... 38
7.7.4 Disable Attendance Mode .......................................................................................... 39
7.8 Time and Attendance Management .................................................................................... 40
7.8.1 Attendance Configuration Flow .................................................................................. 40
7.8.2 Manage Department (Edit/Search/Reset) .................................................................. 40
7.8.3 Shift Management ...................................................................................................... 41
7.8.4 Manage Holiday (Add/Search/Edit/Delete) ................................................................ 44
7.8.5 Shift Schedule ............................................................................................................. 45
7.8.6 Export Attendance Report .......................................................................................... 48
7.9 Data Transfer ........................................................................................................................ 49
7.10 Basic Settings ..................................................................................................................... 50
7.10.1 Set Time .................................................................................................................... 50
7.10.2 Manage System Data ................................................................................................ 51
7.10.3 Set System Parameters ............................................................................................. 52
7.10.4 System Upgrade ........................................................................................................ 53
7.10.5 Restore Settings ........................................................................................................ 54
7.10.6 Log Query .................................................................................................................. 54
7.10.7 View System Information .......................................................................................... 55
Chapter 8 Client Software Configuration ................................................................................... 57
xi
8.1 Add Device ........................................................................................................................... 57

8.1.1 Add Online Device ....................................................................................................... 57
8.1.2 Add Device by IP Address or Domain Name ............................................................... 59
8.1.3 Add Devices by IP Segment ......................................................................................... 61
8.1.4 Add Device by EHome Account ................................................................................... 62
8.1.5 Import Devices in a Batch ........................................................................................... 63
8.2 Person Management ............................................................................................................ 64
8.2.1 Add Organization ........................................................................................................ 64
8.2.2 Configure Basic Information ....................................................................................... 65
8.2.3 Issue a Card by Local Mode ......................................................................................... 65
8.2.4 Collect Fingerprint via Client ....................................................................................... 67
8.2.5 Collect Fingerprint via Access Control Device ............................................................. 68
8.2.6 Configure Access Control Information ........................................................................ 69
8.2.7 Customize Person Information .................................................................................... 69
8.2.8 Configure Additional Information ............................................................................... 70
8.2.9 Import and Export Person Identify Information .......................................................... 70
8.2.10 Import Person Information ....................................................................................... 71
8.2.11 Export Person Information ........................................................................................ 71
8.2.12 Get Person Information from Access Control Device ................................................ 72
8.2.13 Move Persons to Another Organization .................................................................... 72
8.2.14 Issue Cards to Persons in Batch ................................................................................. 73
8.2.15 Report Card Loss ....................................................................................................... 73
8.2.16 Set Card Issuing Parameters ...................................................................................... 73
8.3 Configure Schedule and Template ....................................................................................... 74
8.3.1 Add Holiday ................................................................................................................. 75
8.3.2 Add Template .............................................................................................................. 75
8.4 Set Access Group to Assign Access Authorization to Persons .............................................. 77
8.5 Configure Advanced Functions ............................................................................................ 78
xii
8.5.1 Configure Device Parameters ...................................................................................... 78

8.5.2 Configure Remaining Open/Closed ............................................................................. 83
8.5.3 Configure Custom Wiegand Rule ................................................................................ 84
8.5.4 Configure Card Reader Authentication Mode and Schedule ...................................... 85
8.5.5 Configure Other Parameters ....................................................................................... 87
8.6 Configure Linkage Actions for Access Control ...................................................................... 90
8.6.1 Configure Client Actions for Access Event ................................................................... 91
8.6.2 Configure Device Actions for Access Event ................................................................. 92
8.6.3 Configure Device Actions for Card Swiping ................................................................. 92
8.6.4 Configure Device Actions for Person ID ...................................................................... 93
8.7 Door Control ........................................................................................................................ 94
8.7.1 Control Door Status ..................................................................................................... 94
8.7.2 Check Real-Time Access Records ................................................................................ 95
8.8 Event Center ........................................................................................................................ 96
8.8.1 Enable Receiving Events from Devices ........................................................................ 96
8.8.2 View Real-Time Events ................................................................................................ 97
8.8.3 Search Historical Events .............................................................................................. 99
8.9 Time and Attendance ......................................................................................................... 102
8.9.1 Configure Attendance Parameters ............................................................................ 102
8.9.2 Add General Timetable ............................................................................................. 107
8.9.3 Add Shift .................................................................................................................... 109
8.9.4 Manage Shift Schedule ............................................................................................. 112
8.9.5 Manually Correct Check-in/out Record ..................................................................... 115
8.9.6 Add Leave and Business Trip ..................................................................................... 116
8.9.7 Calculate Attendance Data ........................................................................................ 117
8.9.8 Attendance Statistics ................................................................................................ 118
Chapter 9 Remote Configuration (Web) .................................................................................. 122
9.1 View Device Information .................................................................................................... 122
xiii
9.2 Change Device Password ................................................................................................... 123

9.3 Time Management ............................................................................................................. 123
9.4 System Maintenance .......................................................................................................... 124
9.5 Configure RS-485 Parameters ............................................................................................ 125
9.6 Security Mode Settings ...................................................................................................... 125
9.7 Network Parameters Settings ............................................................................................ 126
9.8 Report Strategy Settings .................................................................................................... 126
9.9 Network Center Parameters Settings ................................................................................. 126
9.10 Configure Wi-Fi ................................................................................................................ 127
9.11 Set Relay Parameters ....................................................................................................... 127
9.12 Set Access Control Parameters ........................................................................................ 127
9.13 Configure Volume Input or Output .................................................................................. 128
9.14 Operate Relay ................................................................................................................... 128
9.15 View Relay Status ............................................................................................................. 128
Chapter 10 Mobile Client Configuration .................................................................................. 129
10.1 Control Door Status ......................................................................................................... 129
10.2 Set Door Open Duration .................................................................................................. 130
10.3 Change Super Password ................................................................................................... 131
10.4 View Access Control Logs ................................................................................................. 132
Appendix A. Tips for Scanning Fingerprint ............................................................................... 133
Appendix B. Access Control Capacity ...................................................................................... 135
Appendix C. Attendance Record Deleting Rule ........................................................................ 137
Appendix D. Attendance Report Table .................................................................................... 138
Appendix E. Custom Wiegand Rule Descriptions ..................................................................... 142
Appendix F. Communication Matrix and Device Command ..................................................... 144
xiv
Chapter 1 Overview
DS-K1T804A series fingerprint access control terminal is designed with a 2.4-inch LCD display
screen. Offline operation, wired network (TCP/IP) and wireless network transmission modes are
supported as well. (The models with -1 do not support the wireless network function.)
1
Chapter 2 Features
• Physical doorbell button design, supports connecting external doorbell
• Integrated management of access control and the attendance
• 2.4-inch LCD screen to display the time, the date and swiping/fingerprint authentication results
• Transmission modes of wired network (TCP/IP) and wireless network
• Max. 3000 users, Max. 3000 fingerprints, Max. 100,000 event records, and Max. 150,000
attendance records
• Different authentication types can be configured according to different situations
• Stand-alone operation: locally adds person, card and fingerprint information
• Exports the swiping card data and the attendance report to the USB flash drive
• Up to 32 normal shifts, up to 32 man-hour shifts, and up to 32 attendance holiday schedules can
be configured
• Generates the attendance report automatically
• Terminal authentication and user authentication
• EM card reading (For DS-K1T804AEF)
• Mifare card reading, including card No. reading (For DS-K1T804AMF)
• DESfire card or Mifare card reading (For DS-K1T804ADF)
• Tampering detection, unlocking overtime alarm, invalid card swiping over times alarm, duress
card alarm, and so on
• Supports multiple languages: English, Vietnamese, Brazilian Portuguese, Spanish, French, Italian,
Arabic, and Thai
• Accurate data and time display provided by built-in electronic clock
• Check the device running status via the Watchdog. When exception status occurs, the system
will reboot automatically
• Data can be permanently saved after power-off
• Remotely control via the client software
• Supports the third party arming
• Supports transmitting data via EHome to realize the whole network transmitting
• Operates via Hik-Connect mobile client
• NFC tag anti-cloning
2
Chapter 3 Appearance Description

View the device appearance and the keypad's description.
Figure 3-1 Device Appearance
Note
The pictures here are for reference only. Some models do not support card swiping function. For
details, refer to the actual product.
Table 3-1 Appearance Description

No. Description
1 Keypad
2 Door Bell Button
3 Fingerprint Reading Module
4 2.4-inch LCD Display Screen Indicator
5 USB Interface/Reset Button (Inside the Cover)
6 Tamper-proof Button
7 Ethernet Port
8 RS-485/Wiegand Wiring Terminal
9 12V Power Interface
10 Door Lock Wiring Terminal
11 Alarm Wiring Terminal
3
Figure 3-2 Keypad Description

Table 3-2 Keypad Description
No. Description
1 Exiting Key: Press the button to exit the menu.
Note
If you enable the attendance status function, the exiting key can be the
shortcut key of the attendance status.
2 Direction Keys: Use direction keys to move the cursor in the menu.
Note
• If you enable the attendance status function, the direction keys can
be the shortcut key of the attendance status.
• If you are in the entering page, use the direction key to change the
input method.
3 Numeric Keys/Letter Keys: Press to input numbers or letters.
Note
Key 0 can also represent a space key except you are using the number
input method.
4 OK Key: Press OK key to confirm operations. Hold the key for 2 s to enter
the login interface.
4
No. Description
Note
If you enable the attendance status function, the OK key can be the
shortcut key of the attendance status.
5 Deleting Key: Press the key to delete the letters or numbers one by one
in the textbox.
6 Editing Key: Hold the key to shift among numbers/lowercases, numbers/
uppercases and symbols.
5
Chapter 4 Device Wiring
4.1 Terminal Description

The terminal diagram are as follows.
6
Figure 4-1 Terminal Diagram
7
Table 4-1 Wiring with Secure Door Control Unit Description

Cable Group No. Function Color Terminal Description
Name
Group A A1 Power Input Red +12 V 12 VDC Power
Supply
A2 Black GND GND
Group B B1 Alarm Input Yellow/Blue IN1 Alarm Input 1
B2 Yellow/Black GND GND
B3 Alarm Output Yellow/Purple NC Alarm Output
Wiring
B4 Yellow/Brown COM
B5 Yellow/Red NO
Group C C1 RS-485 Yellow 485+ RS-485 Wiring
Communicatio
C2 Blue 485-
n
C3 Wiegand Green W0 Wiegand
Wiring 0
C4 White W1 Wiegand
Wiring 1
C5 Brown WG_OK Wiegand
Authenticated
C6 Orange WG_ERR Wiegand
Authentication
Failed
C7 Purple WG_BEEP Buzzer Wiring
C8 Gray WG_TAMP Tampering
Alarm Wiring
C9 Black GND GND
Group D D1 Lock White/Purple NC Lock Wiring
D2 White/Yellow COM
D3 White/Red NO
D4 Yellow/Green SENSOR Door Contact
Signal Input
D5 White/Black GND GND
8
Cable Group No. Function Color Terminal Description

Name
D6 Yellow/Grey BUTTON Exit Door
Wiring
D7 Doorbell White/Brown BELL+ Doorbell
Wiring
D8 White/Blue BELL-
4.2 External Device Wiring

Wire the external device.
The wiring diagram is as follows.
Figure 4-2 External Device Wiring
Note
The external power supply and the access control terminal should use the same GND cable.
4.3 Secure Door Control Unit Wiring

The wiring diagram is as follows:
9
Figure 4-3 Secure Door Control Unit Wiring
Note
• The external power supply and the secure door control unit should use the same GND cable.
• If you want to connect secure door control unit, you should set the connection mode as Connect
Extension Module in the RS-485 settings in the client software.
10
Chapter 5 Installation
Before You Start
• Make sure that the device in the package is in good condition and all the assembly parts are
included.
• Make sure that the wall is strong enough to withstand three times the weight of the device.
Steps
1. Install 120 gang box into the wall.
Figure 5-1 Install Gang Box

2. Route the cables through the cable hole of the mounting plate.
3. Secure the device mounting plate on the gang box with 2 screws (supplied).
Figure 5-2 Install Mounting Plate

4. Wire the corresponding cables.
5. Align the device with mounting plate. Push the terminal in the mounting plate from bottom up.
Fasten the terminal with the buckles on the plate.
11
Figure 5-3 Install Device

6. Fix the device with one screw on the mounting plate and complete the installation.
Figure 5-4 Secure
Note
The pictures in this documentation are for references only, refer to the actual product.
12
Chapter 6 Activation
You should activate the device before the first login. After powering on the device, the system will
switch to Device Activation page.
Activation via the device, SADP tool and the client software are supported.
The default values of the device are as follows:
• The default IP address: 192.0.0.64
• The default port No.: 8000
• The default user name: admin
6.1 Activate via Device

If the device is not activated before first login, the system will enter the Device Activation interface
after powering on.
Steps
1. Create a device password for activation.
2. Confirm the password.
Note
Press the up or down key on the keypad to change the input method.
3. Press OK to activate the device.
Note
We highly recommend you to create a strong password of your own choosing (using a minimum
of 8 characters, including at least three kinds of following categories: upper case letters, lower
case letters, numbers, and special characters) in order to increase the security of your product.
And we recommend you change your password regularly, especially in the high security system,
changing the password monthly or weekly can better protect your product.
What to do next
After the device activation, you will enter the administrator adding page. Add an administrator
before other operations.
6.2 Activate via SADP

SADP is a tool to detect, activate and modify the IP address of the device over the LAN.
13
Before You Start

• Get the SADP software from the supplied disk or the official website http://
www.hikvision.com/en/ , and install the SADP according to the prompts.
• The device and the PC that runs the SADP tool should be within the same subnet.
The following steps show how to activate a device and modify its IP address. For batch activation
and IP addresses modification, refer to User Manual of SADP for details.
Steps
1. Run the SADP software and search the online devices.
2. Find and select your device in online device list.
3. Input new password (admin password) and confirm the password.
Caution
STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of
your own choosing (using a minimum of 8 characters, including upper case letters, lower case
letters, numbers, and special characters) in order to increase the security of your product. And
we recommend you reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your product.
4. Click Activate to start activation.
Status of the device becomes Active after successful activation.

5. Modify IP address of the device.
1) Select the device.
2) Change the device IP address to the same subnet as your computer by either modifying the
IP address manually or checking Enable DHCP.
3) Input the admin password and click Modify to activate your IP address modification.
14
6.3 Activate Device via Client Software

For some devices, you are required to create the password to activate them before they can be
added to the software and work properly.
Steps
Note
This function should be supported by the device.
1. Enter the Device Management page.
2. Click on the right of Device Management and select Device.
3. Click Online Device to show the online device area.
The searched online devices are displayed in the list.
4. Check the device status (shown on Security Level column) and select an inactive device.
5. Click Activate to open the Activation dialog.
6. Create a password in the password field, and confirm the password.
Caution
The password strength of the device can be automatically checked. We highly recommend you
change the password of your own choosing (using a minimum of 8 characters, including at least
three kinds of following categories: upper case letters, lower case letters, numbers, and special
characters) in order to increase the security of your product. And we recommend you change
your password regularly, especially in the high security system, changing the password monthly
or weekly can better protect your product.
Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
7. Click OK to activate the device.
15
Chapter 7 Local Settings
7.1 Select Language

You can select a language for the device system.
After the device activation, you can select a language for the device system.
By default, the system language is English.
Note
After you change the system language, the device will reboot automatically.
7.2 Add Administrator

After the device activation and system language selection, you are required to add an
administrator. You can set the administrator's user name, the card No. You can also add the user
fingerprint, set the department, the template, the authentication mode, and the role.
Steps
1. Move the cursor and select User → New to enter the New page.
16
Figure 7-1 Add Administrator

2. Enter the new user's parameters.
ID (Employee ID)
By default, the ID No. will be increased in sequence. You can edit the ID according to your
preference.
Note
• The ID refers to the user attendance serial No.
• The ID should be between 1 and 99999999 and should not start with 0.
• The ID should be used for once.
Name
Enter the new user name.
Note
• Press the up or down key on the keypad to change the input method.
• Up to 64 characters are allowed in the user name.
Card
Set: Swipe card on the card swiping area or enter card No. manually, and select a card
property.
17
View Info.: View the user's added card information.
Note
• The card No. is required.
• Up to 20 digits can be contained in the card No.
• The card No. can be 0.
• The card No. can start with 0 when it contains more than one numbers. E.g. 012345.
• The card No. should be used for once.
• If device does not support swiping card, you should enter the card No. manually. If you
need to enter the card No. manually, you should enable Press Key to Input Card No.. For
details, see Configure Parameters for Access Control Device .
FP (Fingerprint)
On the Fingerprint page, select a target finger and record according to the voice prompt.
Note
• The same fingerprint cannot be repeatedly added.
• Up to 10 fingerprints can be added to one user.
• You can also scan the fingerprints via the external fingerprint recorder and apply the
fingerprints to the device by the client software.
• For detailed information about scanning the fingerprint, see Tips for Scanning Fingerprint .
Dept. (Department)
Select a department in the list and edit the department.
Note
For detailed information about editing the department, see .
Plan (Template)
Move the cursor and select Set and select a template from the list.
Note
For details about editing template, see Set Schedule Template .
Auth.
Select an authentication mode when verifying user's permission.
Note
• If you select the authentication mode as Controller, you should set the authentication
mode in Set Access Control Parameters . The system will authenticate user's identity
18
according to the configured authentication mode. By default, the authentication mode is

Controller. This mode is applicable to edit users' authentication modes in batch.
• If an user needs to use a special authentication mode, which is different from the
authentication mode configured in Set Access Control Parameters , he can use card/
fingerprint, card, etc. The system will authenticate the user's identity according to the
configured authentication mode first. This mode is applicable to edit single user's
authentication mode, which has special permissions.
Role
Select the user's role as administrator or normal user.
• Admin: The admin has all permissions to operate the device.
• User: The normal user can check attendance on the initial page.
Note
• All persons can enter the main page by entering the device password to operate if there is
no admin user configured.
• After configuring the admin, you should authenticate the admin to enter the main page.
• You can use the USB interface to import the user information. For details, see Data
Transfer.
3. Press ESC, and select Yes to save the settings and exit the page.
7.3 Local Login

Log in the device as an administrator to mange the device parameters, including the
communication, the user, the access control parameters, the attendance, the time, the report, the
system, etc.
Hold OK for 3 s to enter the login page. Select FP, Device PWD, or Card, and authenticate to enter
the home page.
Note
• The login page varies depending on different device model. When operation, refer to the actual
device page.
7.4 Communication Settings

Set device network, EHome, Hik-Connect service, etc.
19
7.4.1 Set Network

You can set the device network parameters, including the IP address, the subnet mask, the gateway
address, and the DHCP.
Steps
1. Move the cursor and select Comm. → Network .
2. Press OK to enter the Network page.
3. Edit the IP address, the subnet mask, and the gateway.
Note
The device's IP address and the PC's should be in the same network segment.
4. Optional: Enable DHCP.
The system will automatically assign IP address for the device.
5. Press ESC and select Yes to save the parameters and return to the previous menu.
7.4.2 Set Wi-Fi Parameters

You can enable the Wi-Fi function and you can transmit the data via Wi-Fi.
Steps
Note
The function is supported by parts of the device models.
1. Move the cursor and select Comm. → Wi-Fi .
2. Press OK to enter the Wi-Fi page.
Figure 7-2 Wi-Fi Page

3. Enable the Wi-Fi function.
20
4. Select a Wi-Fi from the list and set the Wi-Fi parameters, including the Wi-Fi password and
DHCP.
- Enable DHCP, and the system will automatically assign IP address for the Wi-Fi.
- Disable DHCP, and you should set the IP address, subnet mask, and gateway.
5. Press ESC and select Yes to save the parameters.
7.4.3 Change Verification Code

You can change the device verification code before you add the device to the Hik-Connect mobile
client.
Before You Start
Make sure your device has connected to a network.
Steps
1. Move the cursor and select Comm. → Mobile-App .
2. Input a new device verification code in the Verification Code.
Result
The device verification code is changed. You should input the new verification code when you add
the device to the Hik-Connect mobile client.
7.4.4 Set EHome Parameters

Set EHome parameters and the device can upload data via EHome protocol.
Before You Start
Make sure your device has connect to a network.
Steps
1. Move the cursor and select Comm. → EHome .
21
Figure 7-3 EHome Settings

2. Enable the EHome function and set the EHome server parameters.
Center Group 1
Enable center group 1 and the data will be uploaded to the center group.
EHome
Enable EHome function and the data will be uploaded via EHome protocol.
Address Type
Select an address type according to your actual needs.
IP Address
Set the EHome server's IP address.
Port No.
Set the EHome server's port No.
EHome Version
Set the EHome version according to your actual needs. If you choose V5.0, you should create
an account and EHome key. If you choose other version, you should create an EHome
account only.
Note
• Remember the EHome account and EHome key. You should enter the account name or the
key when the device should communicate with other platforms via EHome protocol.
• EHome key range: 8 to 32 characters.
22
7.4.5 Set Wiegand Parameters

You are able to set the Wiegand direction (send/receive) and the Wiegand mode (Wiegand 26/
Wiegand 34).
Steps
1. Move the cursor and select Comm. → Wiegand .
2. Set the Wiegand parameters.
Direction
Send
The device can connect to the access controller to upload the card No. bia the Wiegand 26
or the Wiegand 34 mode.
Receive
The terminal can connect to the Wiegand card readers. No need to configure the Wiegand
mode.
Mode
Wiegand 26 and Wiegand 34 can be selected. The default Wiegand mode is Wiegand 34.
Note
If you change the external device, and after you save the device parameters, the device will
reboot automatically.
7.4.6 Set RS-485 Parameters

The face recognition terminal can connect external secure door control unit or card reader via the
RS-485 terminal.
Steps
1. Move the cursor and select Comm. → RS-485 on the Home page to enter the RS-485 page.
23
Figure 7-4 Set RS-485 Parameters

2. Select an peripheral type according to your actual needs.
3. Press ESC and select Yes to save the settings.
7.5 Person Management
7.5.1 Add Person

You can add users by setting the ID No., the user name, and the card No. You can also record the
user fingerprint, set the password, the department, the template, the role and the authentication
mode.
Steps
1. Move the cursor and select User → New to enter the New page.
24
Figure 7-5 New Page

2. Enter the new user's parameters.
ID (Employee ID)
By default, the ID No. will be increased in sequence. You can edit the ID according to your
preference.
Note
• The ID refers to the user attendance serial No.
• The ID should be between 1 and 99999999 and should not start with 0.
• The ID should be unique.
Name
Enter the new user name.
Note
• Up to 64 characters are allowed in the user name.
Card
Set: Swipe card on the card swiping area or enter card No. manually, and select a card
property.
25
View Info.: View the user's added card information.
Note
• The card No. is required.
• Up to 20 digits can be contained in the card No.
• The card No. can be 0.
• The card No. can start with 0 when it contains more than one numbers. E.g. 012345.
• The card No. should be unique.
• If the device does not support swiping card, you should enter the card No. manually. If you
need to enter the card No. manually, you should enable Press Key to Input Card No.. For
details, see Configure Parameters for Access Control Device .
FP (Fingerprint)
On the Fingerprint page, select a target finger and record according to the voice prompt.
Note
• The same fingerprint cannot be repeatedly added.
• Up to 10 fingerprints can be added to one user.
• You can also scan the fingerprints via the external fingerprint recorder and apply the
fingerprints to the device by the client software.
• For detailed information about scanning the fingerprint, see Tips for Scanning Fingerprint .
Dept. (Department)
Select a department in the list and edit the department.
Note
For detailed information about editing the department, see .
Plan (Template)
Move the cursor and select Set and select a template from the list.
Note
For details about editing template, see Set Schedule Template .
Auth.
Select an authentication mode when verifying user's permission.
Note
• If you select the authentication mode as Controller, you should set the authentication
mode in Set System Parameters . The system will authenticate user's identity according to
26
the configured authentication mode. By default, the authentication mode is Controller.

This mode is applicable to edit users' authentication modes in batch.
• If an user needs to use a special authentication mode, which is different from the
authentication mode configured in Set System Parameters , he can use card/fingerprint,
card, etc. The system will authenticate the user's identity according to the configured
authentication mode first. This mode is applicable to edit single user's authentication
mode, which has special permissions.
Role
Select the user's role as administrator or normal user.
• Admin: The admin has all permissions to operate the device.
• User: The normal user can check attendance on the initial page.
Note
• All persons can enter the main page by entering the device password to operate if there is
no admin user configured.
• After configuring the admin, you should authenticate the admin to enter the main page.
• You can use the USB interface to import the user information. For details, see Data
Transfer.
3. Press ESC, and select Yes to save the settings and exit the page.
7.5.2 Manage Person (Search/Edit/Delete)

Search, edit, delete the added users. You can also manage added fingerprints, manage user's cards.
Search User
Move the cursor and select User → User to enter the user list.
Enter the user's name or employee ID in the search box, and press OK to start search.
Edit User
Move the cursor and select User → User to enter the user list. Select an user in the list and press
OK.
Select Edit User and refer to Add Person to edit the user's information.
Press ESC, and select Yes to save the settings.
Delete
You can delete user, delete password, clear fingerprint, and clear card.
Delete User
Delete the selected user.
Clear FP
Clear the all added fingerprints of the selected user.
27
Clear Card
Delete all added cards of the selected user.
7.6 Access Control

Configure the access control permission, including the access control parameters, the holiday
group, the week plan and the schedule template.
7.6.1 Access Control Configuration Flow

The suggested configuration flow is as follows:
Figure 7-6 Work Flow

ACS (Access Control Parameters)
Set the device's access control parameters, including the device authentication, the sub reader
authentication, the door contact status, the open duration, the door-open timeout alarm, and
the authentication times exceeded, and the super password.
Holiday (Holiday Group)
Configure the holiday group for the access control function. In the setting duration, the
attendance will be failed and the door cannot be controlled.
WK. Plan (Week Plan)
Configure the week plan for the access control function. The door can be controlled during the
configured time.
Template (Schedule Template)
Set the configured week plan and the holiday group. The door can be controlled in the
configured time duration.
7.6.2 Set Access Control Parameters

Set the device's access control parameters, including the device authentication, the sub reader
authentication, the door contact status, the open duration, the door-open timeout alarm, and the
authentication times exceeded, and the super password.
On the Home page, move the cursor and select ACS (Access Control Settings) to enter the Access
Control Settings page. Edit the access control parameters on this page.
28
Figure 7-7 Access Control Parameters

The available parameters descriptions are as follows:
Table 7-1 Access Control Parameters Descriptions
Parameter Description
Terminal Auth Select the face recognition terminal's authentication mode. You
can also customize the authentication mode.
Note
• Only the device with the fingerprint module supports the
fingerprint related function.
• Biometric recognition products are not 100% applicable to
anti-spoofing environments. If you require a higher security
level, use multiple authentication modes.
• If you adopt multiple authentication modes, you should
authenticate other methods before authenticating face.
Sub Reader Auth Select the card reader's authentication mode.

Door Contact You can select "Remain Open" or "Remain Closed" according to
your actual needs. By default, it is Remain Closed.
Open Duration Set the door unlocking duration. If the door is not opened for
the set time, the door will be locked. Available door locked time
range: 1 to 255s.
29
Parameter Description
Door-Open Timeout Alarm Configure the maximum time duration for door opening. If the
door-open time has exceeded the configured value, it will trigger
an alarm.
Auth Times Exceeded Alarm Configure the maximum times for authentication.
Super Password Set the device super password. After saving the settings, you can
input the super password in the initial interface to access the
door.
7.6.3 Set Holiday Group

Configure the access control system holiday schedule. The door can be open during the holiday.
Steps
1. Move the cursor and select ACS → Holiday to enter the holiday settings page.
Figure 7-8 Holiday Group List

2. Move the cursor and select New. Set the holiday group's name.
30
Figure 7-9 Add Holiday Group

3. Add new holiday.
1) Select New ACS Holiday.
31
Figure 7-10 Add New Holiday

2) Set the holiday name, start and end time.
3) Set the holiday period for access.
Note
Up to 8 periods can be edited.
During the holiday time, the attendance will be invalid and the person cannot control the door
status.
4. Press ESC and select Yes to save the parameters and exit the page. The configured holiday group
will be displayed in the holiday group list.
5. Optional: You can also search, edit, or delete the holiday group.
32
7.6.4 Set Week Plan

Configure the week plan for the access control function. The door can be controlled during the
configured time.
Steps
1. Tap ACS → WK. Plan .
Figure 7-11 Week Plan List

2. Move the cursor and select New.
33
Figure 7-12 Add New Week Plan

3. Set the week plan's parameters, including the week plan name, the week plan time,a the
periods.
Note
The person can take attendance or control the door status according to the configured week
plan.
4. Press ESC and select Yes to save the settings and exit the page.
5. Optional: You can also search, edit, or delete the week plan.
Result
The week plan will displayed in the week plan list.
34
7.6.5 Set Schedule Template

Set the configured week plan and the holiday group. The door can be controlled in the configured
time duration.
Steps
1. Tap ACS → Template .
Figure 7-13 Template List

2. Move the cursor and select New.
Figure 7-14 Add New Template

3. Configure the schedule template parameters, including the template name, the week plan and
the holiday group.
5. Optional: You can also search, edit, or delete the template.
35
7.7 Attendance Status

Set attendance mode and choose attendance status. You can set the attendance status as check in,
check out, break out, break in, overtime in, and overtime out according to your actual situation.
7.7.1 Set Auto Attendance

Set the attendance mode as auto, and you can set the attendance status and its available schedule.
The system will auto change the attendance status according to the configured parameters.
Before You Start
Add at least one person, and set the person's authentication mode. For details, see Person
Management .
Steps
1. Move the cursor and select System → Att. Status to enter the Attendance Status page.
2. Move the cursor and select Attendance Mode and set the attendance mode as Auto.
Figure 7-15 Auto Mode
Note
Make sure the attendance status is enabled. By default, it is enabled.
3. Press ESC and save the attendance mode.
4. Move the cursor and select Shortcut Key and define the shortcut key's attendance status and
schedule.
Note
The attendance status will be valid within the configured schedule. For example, if set the Up
key as check in and the Down key as check out, and set the check in's schedule as Monday
36
08:00, and check out's schedule as Monday 17:00, the valid person's authentication before
17:00 on Monday will be marked as check in. And the valid person's authentication after 17:00
on Monday will be marked as check out.
5. Press ESC and save the settings.
Result
Enter the initial page, the current attendance mode will be displayed on the page. When you
authenticate on the initial page, the authentication will be marked as the configured attendance
status according to the configured schedule.
7.7.2 Set Manual Attendance

Set the attendance mode as manual, and you can select a status manually when you take
attendance.
Before You Start
Management .
Steps
2. Move the cursor and select Attendance Mode and set the attendance mode as Manual.
Figure 7-16 Manual Mode
Note
4. Move the cursor and select Shortcut Key and define the shortcut key's attendance status.
37
Result
Press a key on the keypad to select an attendance status and authenticate. The authentication will
be marked as the configured attendance status according to the defined shortcut key.
Or when you authenticate on the initial page, you will enter the Select Status page. Select a status
to take attendance.
Note
If you do not select a status for about 20 s, the authentication will be failed and it will not be
marked as a valid attendance.
7.7.3 Set Manual and Auto Attendance

Set the attendance mode as manual and auto and the system will auto change the attendance
status according to the configured parameters. At the same time you can manually change the
attendance status before the authentication.
Before You Start
Management .
Steps
2. Move the cursor and select Attendance Mode and set the attendance mode as Manual and
Auto.
Figure 7-17 Manual and Auto Mode
Note
38
4. Move the cursor and select Shortcut Key and define the shortcut key's attendance status and
schedule.
Note
The attendance status will be valid within the configured schedule. For example, if set the Up
key as check in and the Down key as check out, and set the check in's schedule as Monday
08:00, and check out's schedule as Monday 17:00, the valid person's authentication before
17:00 on Monday will be marked as check in. And the valid person's authentication after 17:00
on Monday will be marked as check out.
Result
Enter the initial page, the current attendance mode will be displayed on the page. If you do not
select a status, the authentication will be marked as the configured attendance status according to
the schedule. If you press the key on the keypad, and select a status to take attendance, the
authentication will be marked as the selected attendance status.
7.7.4 Disable Attendance Mode

Disable the attendance mode and the system will not display the attendance status on the initial
page.
Move the cursor and select System → Att. Status to enter the Attendance Status page.
Move the cursor and select Attendance Mode and set the attendance mode as Disable.
Figure 7-18 Disable Attendance Mode

The attendance status function is disabled, and you will not view or configure the attendance
status on the initial page.
39
7.8 Time and Attendance Management

Manage department, shift, holiday, schedule, and report.
You can add, edit, delete department/shift/holiday/schedule. You can also export the attendance
report.
Move the cursor and select Attendance to enter the Attendance page.
7.8.1 Attendance Configuration Flow
Figure 7-19 Attendance Configuration Flow
7.8.2 Manage Department (Edit/Search/Reset)

You can edit the department name, view the shift type and the shift name. You can also search the
department by department name, or reset department parameters.
Edit Department
Move the cursor to the Dept., and press OK to enter the department list.
Select a department from the list and select Edit, and press OK to enter the Edit Dept. page. You
can edit the department name, view the shift type and the shift name.
Figure 7-20 Edit Department Page
Note
• The department name supports numbers, uppercase letters, lowercase letters, and symbols.
• Up to 32 characters are supported in the department name.
40
• You can configure the shift in the Shift Management. For detailed information, see Shift
Management .
• By default, the system contains 32 departments.
Search Department
Search the target department by entering the department name.
Enter the department name in the search box, and press OK to start search.
Reset Department
Reset all parameters of the target department to the default ones.
Select a department from the list and select Reset, and press OK. All parameters will be reset to
default ones.
7.8.3 Shift Management

The normal shift and the man-hour shift are available to be configured. You can set the attendance
rule and the attendance checking times in the normal shift. You can also set the working hours per
day in the man-hour shift.
Normal Shift: It is applicable to the normal attendance situation.
Man-Hour Shift: It is applicable to the situation with flexible working hours.
Set Attendance Rule for Normal Shift

Move the cursor and select Shift → Normal → Rule , and press OK to enter the Rule page.
41
Figure 7-21 Attendance Rule Page

Set the attendance rule.
On-work Advanced Time
The allowable early duration to go to work.
Latest On-Work Check Time
The allowable late duration to go to work.
Absence Time (Late)
The late arrival threshold duration.
Off-Work Early Time
The allowable early duration to get off work.
Latest Off-Work Check Time
The allowable late duration to get off work.
Absence Time (Early Leave)
The early leave threshold duration.
Note
The available time is from 0 to 1440 min.
Set Normal Shift

Set the normal shift attendance information, including the shift name and the shift period. You can
also reset the normal shift after editing.
Before You Start
Set the attendance rule. For details see Set Attendance Rule for Normal Shift .
42
Steps
1. Move the cursor and select Shift → Normal to enter the Normal page.
Figure 7-22 Normal Shift Page

2. Select a shift and press OK.
Note
By default, the normal shift type includes 2/Day (2 times per day), 4/Day (4 times per day), and
30 custom types.
3. Select Edit and press OK to enter the Edit Shift page.
4. Set the shift name and period in order.
Note
• The shift name supports numbers, uppercase letters, lowercase letters, Chinese characters
and symbols.
• Up to 32 characters are allowed in the shift name.
• Up to 4 time periods can be edited.
5. Press ESC, and select Yes to save the settings.

6. Optional: Select a normal shift and select Reset and the shift will be reset to default value.
Set Man-Hour Shift

Set the man-hour shift parameters, including the shift name, the work duration, the latest on-work
time, and the break time.
Steps
Up to 32 man-hour shifts can be configured.
1. Move the cursor and select Shift → Man-Hour to enter the Man-Hour page.
43
Figure 7-23 Man-Hour Shift Page

2. Select a shift from the list, and press OK .
3. Select Edit to enter the Edit Shift page.
Note
By default, the man-hour shift type includes 6H/Day (6 hours per day), 8H/Day (8 hours per
day), and 30 custom types.
4. Edit shift name, shift duration (work duration), the latest on-work time, and the break time.
Note
• The break time will not be counted into the working hour.
• If the Latest Time (On-Work) is set to 0, the Latest Time function will not be enabled.

6. Optional: Select a shift, press OK, and select Reset to reset the shift to default value.
7.8.4 Manage Holiday (Add/Search/Edit/Delete)

Set the attendance holiday. The attendance will not be recorded during the holiday.
Add Holiday
Move the cursor and select Holiday → New to enter the New page. Enter No., name, start date,
and end date. Press OK to save the settings.
44
Figure 7-25 Add Holiday Page
Search Holiday
Move the cursor and select Holiday → Holiday to enter the holiday list. Enter a holiday name and
press OK to start search.
Edit Holiday
Move the cursor and select Holiday → Holiday to enter the holiday list. Select a holiday and select
Edit to edit the holiday.
Delete Holiday
Move the cursor and select Holiday → Holiday to enter the holiday list. Select a holiday and select
Delete to delete the holiday.
7.8.5 Shift Schedule

Combine shift and holiday according to your actual needs. Scheduling shift by department and
scheduling shift by individual are supported.
Schedule Shift by Department: All persons in the department use the same shift schedule to check
in/out.
Schedule Shift by Individual: Check in/out according to individual's conditions.
Schedule Shift by Department

All persons in the department use the same shift schedule to check in/out.
Before You Start
• Edit department. For details, see Manage Department (Edit/Search/Reset) .
• Set normal shit or man-hour shift. For details, see Set Normal Shift and Set Man-Hour Shift .
45
Steps
1. Move the cursor and select Schedule → Dept. Shift to enter the Dept. Shift page.
2. Select a department from the list and press OK to enter the Edit Shift Schedule by Dept. page.
Figure 7-26 Edit Shift Schedule by Dept. Page

3. Edit parameters.
Dept. Name
The department name should be edited in Edit Dept. page. For details, see Manage
Department (Edit/Search/Reset).
Set Shift
Select a shift type and a shift times.
Start
Set the schedule's start date.
End
Set the schedule's end date.
Add Holiday
Select a holiday from the holiday list. For details about adding holiday, see Manage Holiday
(Add/Search/Edit/Delete) .
Schedule Shift by Individual

Check in/out according to individual's conditions.
46
Before You Start

• Add user before setting schedule shift by individual. For details, see Add Person .
• Set the normal shift or the man-hour shift. For details, see Set Normal Shift and Set Man-Hour
Shift .
Steps
Note
The schedule shift by individual has higher priority than schedule shift by department. If a user has
configured both schedule shift by department and by individual, the system will take attendance
according to schedule shift by individual first.
1. Move the cursor and select Schedule → Individual Shift to enter the Individual Shift page.
2. Select Add Individual Shift and press OK to enter the Add Shift Schedule page.
Figure 7-27 Add Shift Schedule Page

3. Select an individual in the list and press OK to enter the Edit Shift Schedule by Department
page.
4. Edit the parameters.
Set Shift
Select a shift type and a shift times.
Start
Set the schedule's start date.
End
Set the schedule's end date.
Add Holiday
Select a holiday from the holiday list. For details about adding holiday, see Manage Holiday
(Add/Search/Edit/Delete) .
47
7.8.6 Export Attendance Report

Export the attendance record, the attendance report, the abnormal attendance record and the
attendance management schedule.
Steps
1. Plug in a USB flash drive in the USB interface.
Note
• The supported USB flash drive format is FAT32.
• The USB flash drive memory should be from 1G to 32G. Make sure the free space of the USB
flash drive is more than 512 M.
2. Move the cursor and select Report. Press OK to enter the Report page.
Figure 7-28 Report Page

3. Select a report to export.
- When exporting attendance record, attendance report, and abnormal attendance record,
you should enter the device No. attendance start date and end date.
Note
The device No. is for differentiating the reports of different devices.
- When selecting Attendance Management Schedule, shift settings table, normal shift
schedule table and the man-hour shift schedule table will be exported.
Note
For details about the exported tables descriptions, see Attendance Report Table .
The exported table will be saved in the USB flash drive in Excel format.
48
7.9 Data Transfer

You can export the access control parameters (fingerprint and user information) and the
attendance data (data after attendance, card swiping data for instance). You can also import the
access control parameters from the USB flash drive.
Export Data
Move the cursor and select Transfer → Export to enter the Export page.
Figure 7-29 Export Data Page

Plug a USB flash drive in the device USB interface, and select Export ACS Para. or Export
Attendance Data, enter the key, and press OK. The data will be exported to the USB flash drive.
Note
• The USB flash drive memory should be from 1G to 32G. Make sure the free space of the USB
flash drive should be more than 512 M.
• Remember the key property, and you should use the key to import the data to another device.
Import Data
Move the cursor and select Transfer → Import to enter the Import page. Select Import ACS Para,
enter the key, and press OK. The system will gain access control parameters from the USB flash
drive.
Note
• The file for importing should be in the root directory.
49
7.10 Basic Settings
7.10.1 Set Time

Set the device time and DST.
Steps
1. Move the cursor and select Time in the main page and press OK to enter the Time page.
Figure 7-30 Time Page

Date
The displayed date on the device.
Note
The available range is from 1970.01.01 to 2037.12.31.
Time
The displayed time on the device.
DST
Select to enable or disable the DST. When the DST is enabled, you can set the DST bias time,
the start time and the end time.
50
• DST Bias: You can select 30min, 60min, 90min and 120min.
• Start: Set the start time of the DST.
• End: Set the end time of the DST.
7.10.2 Manage System Data

Delete the saved event, attendance data, user data, or permission.
Steps
1. Move the cursor and select System → Data .
2. Press OK to enter the Data page.
Figure 7-31 Data Page

3. Select an item and press OK to delete.
Delete Event Only
Delete all recorded events in the device.
Delete Attendance Data Only
Delete all attendance data in the device.
Delete User Only
Delete all user data in the device, including the attendance records.
Clear Permission
Clear the admin management permission. The admin will turn to the normal user. The user
will not be deleted.
51
7.10.3 Set System Parameters

Set the system parameters, including the device time format, the keypad sound, the voice prompt,
the volume, the sleeping mode, the attendance record prompt the authentication mode, record
delete function, and the language.
Steps
1. Move the cursor and select System → System .
2. Press OK to enter the System page.
Figure 7-32 System Page

Time Format
Select an appropriate time format according to your preference.
Keypad Sound
Enable or disable the keypad sound according to your preference.
Voice Prompt
Enable or disable the voice prompt according to your preference.
Voice Volume
Set the device voice prompt volume.
52
Sleeping
Set the device sleeping waiting time (minute). When you are on the initial page and if you set
the sleeping time to 30 min, the device will sleep after 30 min without any operation.
Note
If you set the sleeping time to 0, the device will not enter sleeping mode.
Wait to Logout
If there is no operation within the configured time, the system will logout.
Record over Threshold Prompt
If the attendance record memory reaches the configured value, the system will pop up a
prompt to remind you. The available value is from 1 to 99.
Note
Up to 50,000 attendance records can be saved.
Auth Mode (Authentication Mode)
The authentication mode can be switched among "Card/FP (fingerprint)", "Card", "FP
(fingerprint)", "Card & Password", "Card & FP (fingerprint)", "FP (fingerprint) & Password",
"Card & FP (fingerprint)" & "Password", and "ID (employee ID) and password".
Record Delete
When the function is enabled, the system will remind you to delete records. The system will
delete the first 3000 attendance records when the memory reaches the configured
threshold, in order to save the new attendance records. By default, the function is enabled.
For details, see Attendance Record Deleting Rule .
Language
Change the system language. After you change the system language, the device will reboot
automatically.
7.10.4 System Upgrade

You can upgrade the system online or locally. The system reads the upgrading file in the plugged
USB flash drive or gain the upgrading package from the platform to upgrade the device.
Steps
1. Move the cursor and select System → Upgrade .
2. Upgrade the system.
- Local Upgrade: Plug the USB flash drive to the USB interface. Press OK. The system will read
the digicap.dav file and upgrading automatically. After the upgrading is completed, the
device will reboot automatically.
53
Note
• The upgrading file should be in the root directory.
• The upgrading file name in the USB flash drive should be digicap.dav.
• Do not power off during the device upgrading.
• After the upgrading is completed, remove the USB flash drive.
- Online upgrade: The system will gain the upgrade package from the platform to upgrade.
7.10.5 Restore Settings

Restore system parameters to factory settings or default settings.
Steps
1. Move the cursor and select System → Reset .
2. Press OK to enter the Reset page.
Figure 7-33 Reset Page

3. Select Factory Settings or Default Settings.
Factory Settings
All parameters of the device will restore to the factory parameters.
Default Settings
All parameters, excluding the communication parameters, the remote user management,
and events, will restore to the factory parameters.
4. Confirm settings in the prompt page and the device starts restoring.
7.10.6 Log Query

You can search the authentication logs via the user's employee ID, name, or card.
Steps
1. On the Home page, move the cursor and select Log.
54
Figure 7-34 Log Query Page

2. Enter the employee ID, the user name, the card No., the start time, and the end time.
3. Press OKto start searching.
The result will be displayed on the page.
7.10.7 View System Information

View system information, including system capacity and device information.
View System Capacity

Move the cursor and select Info. → Capacity to enter the Capacity page.
You can view the added device user number, card number, and fingerprint number.
Note
Parts of device models supports display the fingerprint capacity.
55
Figure 7-35 Capacity Page
View Device Information

Move the cursor and select Info. → Device to enter the Device page.
You can view the device name, the serial No., the MAC address, the firmware, and the production
date.
Figure 7-36 Device Page
56
Chapter 8 Client Software Configuration
8.1 Add Device

The client provides three device adding modes including by IP/domain, IP segment, and ISUP
protocol. The client also supports importing multiple devices in a batch when there are large
amount of devices to be added.
8.1.1 Add Online Device

The active online devices in the same local subnet with the client software will be displayed on the
Online Device area. You can click Refresh Every 60s to refresh the information of the online
devices.
Add Single Online Device

You can add single online device to the client software.
Steps
1. Enter the Device Management module.
2. Optional: Click on the right of Device Management and select Device.
3. Click Online Device to show the online device area.
4. Select an online device from the Online Device area.
Note
For the inactive device, you need to create the password for it before you can add the device
properly. For detailed steps, refer to Activation .
5. Click Add to open the device adding window.
6. Enter the required information.
Name
Enter a descriptive name for the device.
Address
The IP address of the device is obtained automatically in this adding mode.
Port
The port number is obtained automatically.
User Name
By default, the user name is admin.
57
Password
Enter the device password.
Caution
The password strength of the device can be automatically checked. We highly recommend
you change the password of your own choosing (using a minimum of 8 characters, including
at least three kinds of following categories: upper case letters, lower case letters, numbers,
and special characters) in order to increase the security of your product. And we recommend
you change your password regularly, especially in the high security system, changing the
password monthly or weekly can better protect your product.
7. Optional: Check Synchronize Time to synchronize the device time with the PC running the client
after adding the device to the client.
8. Optional: Check Import to Group to create a group by the device name.
Note
You can import all the channels of the device to the corresponding group by default.
9. Click OK to add the device.
Add Multiple Detected Online Devices

For detected online devices sharing the same user name and password, you can add them to the
client in a batch.
Before You Start
Make sure the to-be-added devices are online.
Steps
2. Click Device tab on the top of the right panel.
3. Click Online Device to show the online device area at the bottom of the page.
4. Select multiple devices.
Note
For the inactive device, you need to create the password for it before you can add the device
properly. For details, refer to .
5. Click Add to open the device adding window.
User Name
58

Password
Caution
8. Optional: Check Import to Group to create a group by the device name, and import all the
channels of the device to this group.
Example
For access control device, its access points, alarm inputs/outputs, and encoding channels (if
exist) will be imported to this group.
9. Click Add to add the devices.
8.1.2 Add Device by IP Address or Domain Name

When you know the IP address or domain name of the device to add, you can add devices to the
client by specifying the IP address (or domain name), user name, password, and other related
parameters.
Steps
1. Enter Device Management module.
The added devices are displayed in the list.
3. Click Add to open the Add window.
4. Select IP/Domain as the adding mode.
5. Enter the required information, including name, address, port number, user name, and
password.
Name
Create a descriptive name for the device. For example, you can use a name that can show
the location or feature of the device.
Address
59
The IP address or domain name of the device.

Port
The devices to add have the same port No. The default value is 8000.
User Name
Enter the device user name. By default, the user name is admin.
Password
Caution
Note
8. Finish adding the device.
- Click Add to add the device and back to the device list page.
- Click Add and New to save the settings and continue to add other device.
9. Perform the following operations after adding the devices.
Remote Click on Operation column to set remote configuration of the
Configuration corresponding device.
Note
• For some models of devices, you can open its web window. To open
the original remote configuration window, press Ctrl and click .
• For detail operation steps for the remote configuration, see the user
manual of the device.
Device Status Click on Operation column to view device status.
60
8.1.3 Add Devices by IP Segment

If you want to add devices of which the IP addresses are within an IP segment, you can specify the
start IP address and end IP address, user name, password, and other parameters to add them.
Steps
The added devices are displayed in the list.
4. Select IP Segment as the adding mode.
Start IP
Enter a start IP address.
End IP
Enter an end IP address in the same network segment with the start IP.
Port
Enter the device port No. The default value is 8000.
User Name
Password
Caution
Note
61
- Click Add to add the device and back to the device list page.
9. Optional: Click on Operation column to view device status.
8.1.4 Add Device by EHome Account

For access control devices supports EHome 5.0 protocol, you can add them to the client by EHome
protocol after entering device ID and key, if you have configured their server addresses, port No.,
and device IDs.
Before You Start
Make sure the devices have connected to the network properly.
Steps
1. Enter Device Management module.
The added devices are displayed on the right panel.
3. Select EHome as the adding mode.
Device Account
Enter the account name registered on EHome protocol.
EHome Key
For EHome 5.0 devices, enter the EHome key if you have set it when configuring network
center parameter for the device.
Note
6. Optional: Check Import to Group to create a group by the device name, and import all the
channels of the device to the group.
- Click Add to add the device and go back to the device list.
Note
Face pictures cannot be applied to devices added by EHome account.
8. Optional: Perform the following operation(s).
Edit Device Click on Operation column to edit the device information, such as
Information device name, device account, and EHome key.
62
Check Online User Click on Operation column to check the online users who access
the device, such as user name, user type, user's IP address, and login
time.
Refresh Click on Operation column to get the latest device information.
Delete Device Select one or multiple devices and click Delete to delete the selected
device(s) from the client.
8.1.5 Import Devices in a Batch

You can add multiple devices to the client in a batch by entering the device parameters in a pre-
defined CSV file.
Steps
2. Click Device tab on the top of the right panel.
3. Click Add to open the Add window, and then select Batch Import as the adding mode.
4. Click Export Template and then save the pre-defined template (CSV file) on your PC.
5. Open the exported template file and enter the required information of the devices to be added
on the corresponding column.
Note
For detailed description of the required fields, refer to the introductions in the template.
Adding Mode
Enter 0 or 1 or 2.
Address
Edit the address of the device.
Port
Enter the device port number. The default port number is 8000.
User Name
Enter the device user name. By default, the user name is admin.
Password
Caution
63
Import to Group
Enter 1 to create a group by the device name. All the channels of the device will be imported
to the corresponding group by default. Enter 0 to disable this function.
6. Click and select the template file.
7. Click Add to import the devices.
8. Perform the following operations after adding the devices.
Remote Click on Operation column to set remote configuration of the
Configuration corresponding device.
Note
• For some models of devices, you can open its web window. To open
the original remote configuration window, press Ctrl and click .
• For detail operation steps for the remote configuration, see the user
manual of the device.
8.2 Person Management

You can add person information to the system for further operations such as access control, video
intercom, time and attendance, etc. You can manage the added persons such as issuing cards to
them in a batch, importing and exporting person information in a batch, etc.
8.2.1 Add Organization

You can add an organization and import person information to the organization for effective
management of the persons. You can also add a surbodinate organization for the added one.
Steps
1. Enter Person module.
2. Select a parent organization in the left column and click Add in the upper-left corner to add an
organization.
3. Create a name for the added organization.
Note
Up to 10 levels of organizations can be added.
64
4. Optional: Perform the following operation(s).

Edit Organization Hover the mouse on an added organization and click to edit its
name.
Delete Hover the mouse on an added organization and click to delete it.
Organization
Note
• The lower-level organizations will be deleted as well if you delete an
organization.
• Make sure there is no person added under the organization, or the
organization cannot be deleted.
Show Persons in Check Show Persons in Sub Organization and select an organization to
Sub Organization show persons in its sub organizations.
8.2.2 Configure Basic Information

You can add person to the client software one by one and configure the person's basic information
such as name, gender, phone number, etc.
Steps
2. Select an organization in the organization list to add the person.
3. Click Add to open the adding person window.
The Person ID will be generated automatically.
4. Enter the basic information including person name, gender, tel, email address, etc.
5. Optional: Set the effective period of the person. Once expired, the credentials and access
control settings of the person will be invalid and the person will have no authorization to access
the doors\floors.
Example
For example, if the person is a visitor, his/her effective period may be short and temporary.
6. Confirm to add the person.
- Click Add to add the person and close the Add Person window.
- Click Add and New to add the person and continue to add other persons.
8.2.3 Issue a Card by Local Mode

If a card enrollment station is available, you can issue a card by local mode. To read the card
number, you should connect the card enrollment station to the PC running the client by USB
interface or COM, and place the card on the card enrollment station.
65
Steps
2. Select an organization in the organization list to add the person and click Add to enter Add
Person panel.
Note
Enter the person's basic information first. For details about configuring person's basic
information, refer to Configure Basic Information .
3. In the Credential → Card area, click +.
4. Click Settings to enter the Settings page.
5. Select Local as the card issuing mode.
Figure 8-1 Issue a Card by Local Mode

6. Set other related parameters.
Card Enrollment Station
Select the model of the connected card enrollment station.
66
Note
Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-
M, DS-K1F100-D8E, and DS-K1F180-D8E.
Card Type
This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the
card type as EM card or Mifare card according to the actual card type.
Buzzing
Enable or disable the buzzing when the card number is read successfully.
Card No. Type
Select the type of the card number according to actual needs.
M1 Card Encryption
This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-
D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select
the sector of the card to encrypt.
7. Click OK to confirm the operation.
8. Place the card on the card enrollment station, and click Read to get the card number.
The card number will display in the Card No. field automatically.
9. Click Add.
The card will be issued to the person.
8.2.4 Collect Fingerprint via Client

Collecting fingerprints locally means you can collect the fingerprint via the fingerprint recorder
connected directly to the PC running the client. The fingerprints recorded can be used as
credentials of the persons to access the authorized doors.
Before You Start
Connect the fingerprint recorder to the PC running the client.
Steps
2. Select an organization in the organization list to add the person and click Add.
Note
3. In the Credential → Fingerprint panel, click +.
4. In the pop-up window, select the collection mode as Local.
5. Select the model of the connected fingerprint recorder.
67
Note
If the fingerprint recorder is DS-K1F800-F, you can click Settings to select the COM the
fingerprint recorder connects to.
6. Collect the fingerprint.
1) Click Start.
2) Place and lift your fingerprint on the fingerprint recorder to collect the fingerprint.
3) Click Add to save the recorded fingerprint.
Note
Once the fingerprint is added, the fingerprint type cannot be changed.
8.2.5 Collect Fingerprint via Access Control Device

When adding person, you can collect fingerprint information via the access control device's
fingerprint module. The fingerprints recorded can be used as credentials of the persons to access
the authorized doors.
Before You Start
Make sure fingerprint collection is supported by the access control device.
Steps
Note
3. In the Credential → Fingerprint panel, click +.
4. In the pop-up window, select the collection mode as Remote.
5. Select an access control device which supports fingerprint recognition function from the drop-
down list.
6. Collect the fingerprint.
1) Click Start.
2) Place and lift your fingerprint on the fingerprint scanner of the selected access control device
to collect the fingerprint.
3) Click Add to save the recorded fingerprint.
68
- Click Add and New to add the person and continue to add other persons .
Note
Once the fingerprint is added, the fingerprint type cannot be changed.
8.2.6 Configure Access Control Information

When adding a person, you can set her/his access control properties, such as setting the person as
visitor or as blocklist person, or as super user who has super authorization.
Steps
Note
3. In the Access Control panel, set the person's access control properties.
PIN Code
The PIN code must be used after card or fingerprint when accessing. It cannot be used
independently. It should contain 4 to 8 digits.
Device Operator
For person with device operator role, he/she is authorized to operate on the access control
devices.
Note
The Super User, Extended Door Open Time, Add to Blocklist, and Mark as Visitor functions
cannot be enabled concurrently. For example, if one person is set as super user, you cannot
enable extended door open time for her/him, add her/him to the blocklist, or set her/him as
visitor.
8.2.7 Customize Person Information

You can customize the person properties which are not pre-defined in the client according to actual
needs, e.g., place of birth. After customizing, when add a person, you can enter the custom
information to make the person information complete.
69
Steps
2. Set the fields of custom information.
1) Click Custom Property.
2) Click Add to add a new property.
3) Enter the property name.
4) Click OK.
3. Set the custom information when adding a person.
1) Select an organization in the organization list to add the person and click Add.
Note
2) In the Custom Information panel, enter the person information.
3) Click Add to add the person and close the Add Person window, or click Add and New to add
the person and continue to add other persons.
8.2.8 Configure Additional Information

When adding person, you can configure the additional information for the person, such as person's
identity type, identity No., country, etc., according to actual needs.
Steps
Note
3. In the Additional Information panel, enter the additional information of the person, including
person's ID type, ID No., job title, etc., according to actual needs.
- Click Add and New to add the person and continue to add other persons .
8.2.9 Import and Export Person Identify Information

You can import the information of multiple persons to the client software in a batch. Meanwhile,
you can also export the person information and save them in your PC.
70
8.2.10 Import Person Information

You can enter the information of multiple persons in a predefined template (a CSV file) to import
the information to the client in a batch.
Steps
1. Enter the Person module.
2. Select an added organization in the list, or click Add in the upper-left corner to add an
organization and then select it.
3. Click Import to open the Import panel.
4. Select Person Information as the importing mode.
5. Click Download Template for Importing Person to download the template.
6. Enter the person information in the downloaded template.
Note
• If the person has multiple cards, separate the card No. with semicolon.
• Items with asterisk are required.
• By default, the Hire Date is the current date.
7. Click to select the CSV file with person information.

8. Click Import to start importing.
Note
• If a person No. already exists in the client's database, delete the existing information before
importing.
• You can import information of no more than 10,000 persons.
8.2.11 Export Person Information

You can export the added persons' information to local PC as a CSV file.
Before You Start
Make sure you have added persons to an organization.
Steps
1. Enter the Person module.
2. Optional: Select an organization in the list.
Note
All persons' information will be exported if you do not select any organization.
3. Click Export to open the Export panel and check Person Information as the content to export.
4. Check desired items to export.
5. Click Export to save the exported CSV file in your PC.
71
8.2.12 Get Person Information from Access Control Device

If the added access control device has been configured with person information (including person
details, fingerprint, and issued card information), you can get the person information from the
device and import them to the client for further operations.
Steps
Note
• If the person name stored in the device is empty, the person name will be filled with the issued
card No. after importing to the client.
• The gender of the persons will be Male by default.
• If the card number or person ID (employee ID) stored on the device already exists in the client
database, the person with this card number or person ID will not be imported to the client.

2. Select an organization to import the persons.
3. Click Get from Device.
4. Select the access control device from the drop-down list.
5. Click Get to start importing the person information to the client.
The person information, including person details, person's fingerprint information (if
configured), and the linked cards (if configured), will be imported to the selected organization.
8.2.13 Move Persons to Another Organization

You can move the added persons to another organization if you need.
Before You Start
• Make sure you have added at least two organizations.
• Make sure you have imported person information.
Steps
2. Select an organization in the left panel.
The persons under the organization will be displayed in the right panel.
3. Select the person to move.
4. Click Change Organization.
5. Select the organization to move persons to.
6. Click OK.
72
8.2.14 Issue Cards to Persons in Batch

The client provides a convenient way to issue cards to multiple persons in a batch.
Steps
2. Click Batch Issue Cards.
All the added persons with no card issued will display.
3. Set the card issuing parameters. For details, refer to Set Card Issuing Parameters .
4. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing
cards.
5. Click the card number column and enter the card number.
- Place the card on the card enrollment station.
- Swipe the card on the card reader.
- Enter the card number manually and press Enter key on your keyboard.
The card number will be read automatically and the card will be issued to the person in the list.
6. Repeat the above step to issue the cards to the persons in the list in sequence.
8.2.15 Report Card Loss

If the person lost his/her card, you can report the card loss so that the card's related access
authorization will be inactive.
Steps
2. Select the person you want to report card loss for and click Edit to open the Edit Person
window.
3. In the Credential → Card panel, click on the added card to set this card as lost card.
After reporting card loss, the access authorization of this card will be invalid and inactive. Other
person who gets this card cannot access the doors by swiping this lost card.
4. Optional: If the lost card is found, you can click to cancel the loss.
After cancelling card loss, the access authorization of the person will be valid and active.
5. If the lost card is added in one access group and the access group is applied to the device
already, after reporting card loss or cancelling card loss, a window will pop up to notify you to
apply the changes to the device. After applying to device, these changes can take effect on the
device.
8.2.16 Set Card Issuing Parameters

The client provides two modes for reading a card's number: via card enrollment station or via the
card reader of the access control device. If a card enrollment station is available, connect it to the
73
PC running the client by USB interface or COM, and place the card on the card enrollment to read
the card number. If not, you can also swipe the card on the card reader of the added access control
device to get the card number. As a result, before issuing a card to one person, you need to set the
card issuing parameters including the issuing mode and related parameters.
When adding a card to one person, click Settings to open the Card Issuing Settings window.
Local Mode: Issue Card by Card Enrollment Station

Connect a card enrollment station to the PC running the client. You can place the card on the card
enrollment station to get the card number.
Card Enrollment Station
Select the model of the connected card enrollment station
Note
Currently, the supported card enrollment station model is DS-K1F180-D8E.
Card Type
Select the card type as EM card or IC card according to the actual card type.
Buzzing
Enable or disable the buzzing when the card number is read successfully.
Card No. Type
Select the type of the card number according to actual needs.
M1 Card Encryption
If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should
enable this function and select the sector of the card to encrypt.
Remote Mode: Issue Card by Card Reader

Select an access control device added in the client and swipe the card on its card reader to read
the card number.
8.3 Configure Schedule and Template

You can configure the template including holiday and week schedule. After setting the template,
you can adopt the configured template to access groups when setting the access groups, so that
the access group will take effect in the time durations of the template.
Note
For access group settings, refer to Set Access Group to Assign Access Authorization to Persons .
74
8.3.1 Add Holiday

You can create holidays and set the days in the holidays, including start date, end date, and holiday
duration in one day.
Steps
Note
You can add up to 64 holidays in the software system.
1. Click Access Control → Schedule → Holiday to enter the Holiday page.
2. Click Add on the left panel.
3. Create a name for the holiday.
4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box.
5. Add a holiday period to the holiday list and configure the holiday duration.
Note
Up to 16 holiday periods can be added to one holiday.
1) Click Add in the Holiday List field.
2) Drag the cursor to draw the time duration, which means in that duration of time, the
configured access group is activated.
Note
Up to 8 time durations can be set to one holiday period.
3) Optional: Perform the following operations to edit the time durations.
• Move the cursor to the time duration and drag the time duration on the timeline bar to
the desired position when the cursor turns to .
• Click the time duration and directly edit the start/end time in the appeared dialog.
• Move the cursor to the start or the end of time duration and drag to lengthen or shorten
the time duration when the cursor turns to .
4) Optional: Select the time duration(s) that need to be deleted, and then click in the
Operation column to delete the selected time duration(s).
5) Optional: Click in the Operation column to clear all the time duration(s) in the time bar.
6) Optional: Click in the Operation column to delete this added holiday period from the
holiday list.
6. Click Save.
8.3.2 Add Template

Template includes week schedule and holiday. You can set week schedule and assign the time
duration of access authorization for different person or group. You can also select the added
holiday(s) for the template.
75
Steps
Note
You can add up to 255 templates in the software system.
1. Click Access Control → Schedule → Template to enter the Template page.
Note
There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be
edited or deleted.
All-Day Authorized
The access authorization is valid in each day of the week and it has no holiday.
All-Day Denied
The access authorization is invalid in each day of the week and it has no holiday.
2. Click Add on the left panel to create a new template.

3. Create a name for the template.
4. Enter the descriptions or some notification of this template in the Remark box.
5. Edit the week schedule to apply it to the template.
1) Click Week Schedule tab on the lower panel.
2) Select a day of the week and draw time duration(s) on the timeline bar.
Note
Up to 8 time duration(s) can be set for each day in the week schedule.
4) Repeat the two steps above to draw more time durations on the other days of the week.
6. Add a holiday to apply it to the template.
Note
Up to 4 holidays can be added to one template.
1) Click Holiday tab.
2) Select a holiday in the left list and it will be added to the selected list on the right panel.
3) Optional: Click Add to add a new holiday.
Note
For details about adding a holiday, refer to Add Holiday .
76
4) Optional: Select a selected holiday in the right list and click to remove the selected one,
or click Clear to clear all the selected holiday(s) in the right list.
7. Click Save to save the settings and finish adding the template.
8.4 Set Access Group to Assign Access Authorization to Persons

After adding the person and configuring the person's credentials, you can create the access groups
to define which person(s) can get access to which door(s) and then apply the access group to the
access control device to take effect.
Steps
• For one person, you can add up to 4 access groups to one access control point of one device.
• You can add up to 128 access groups in total.
• When the access group settings are changed, you need to apply the access groups to the devices
again to take effect. The access group changes include changes of template, access group
settings, person's access group settings, and related person details (including card number,
fingerprint, linkage between card number and fingerprint, linkage between card number and
fingerprint, card password, card effective period, etc).
1. Click Access Control → Access Group to enter the Access Group interface.
3. In the Name text field, create a name for the access group as you want.
4. Select a template for the access group.
Note
You should configure the template before access group settings. Refer to Configure Schedule
and Template for details.
5. In the left list of the Select Person field, select person(s) and the person(s) will be added to the
selected list .
6. In the left list of the Select Door field, select door(s) or door station(s) for the selected persons
to access, and the selected door(s) or door station(s) will be added to the selected list.
7. Click OK.
8. After adding the access groups, you need to apply them to the access control device to take
effect.
1) Select the access group(s) to apply to the access control device.
To select multiple access groups, you can hold the Ctrl or Shift key and select access groups.
2) Click Apply All to Devices to start applying all the selected access group(s) to the access
control device or door station.
77
Caution
• Be careful to click Apply All to Devices, since this operation will clear all the access groups
of the selected devices and then apply the new access group, which may brings risk to the
devices.
• You can click Apply Changes to Devices to only apply the changed part of the selected
access group(s) to the device(s).
3) View the apply status in the Status column or click Applying Statusto view all the applied
access group(s).
The selected persons in the applied access groups will have the authorization to enter/exit the
selected doors/door stations with their linked card(s) or fingerprints.
9. Optional: Click to edit the access group if necessary.
8.5 Configure Advanced Functions

You can configure the advanced functions of access control to meet some special requirements in
different scene.
Note
• For the card related functions(the type of access control card), only the card(s) with access group
applied will be listed when adding cards.
• The advanced functions should be supported by the device.
• Hover the cursor on the Advanced Function, and then Click to customize the advanced
function(s) to be displayed.
8.5.1 Configure Device Parameters

After adding the access control device, you can configure the parameters of access control device,
access control points.
Configure Parameters for Access Control Device

After adding the access control device, you can configure its parameters.
Steps
1. Click Access Control → Advanced Function → Device Parameter .
Note
If you can find Device Parameter in the Advanced Function list, Hover the cursor on the
Advanced Function, and then Click to select the Device Parameter to be displayed.
2. Select an access device to show its parameters on the right page.
78
3. Turn the switch to ON to enable the corresponding functions.
Note
• The displayed parameters may vary for different access control devices.
• Some of the following parameters are not listed in the Basic Information page, click More to
edit the parameters.
Voice Prompt
If you enable this function, the voice prompt is enabled in the device. You can hear the voice
prompt when operating in the device.
Enable NFC Card
If enable the function, the device can recognize the NFC card. You can present NFC card on
the device.
Enable M1 Card
If enable the function, the device can recognize the M1 card. You can present M1 card on the
device.
Enable EM Card
If enable the function, the device can recognize the EM card. You can present EM card on the
device.
Enable CPU Card
Reserved. If enable the function, the device can recognize the CPU card. You can present CPU
card on the device.
Enable ID Card
Reserved. If enable the function, the device can recognize the ID card. You can present ID
card on the device.
4. Click OK.
5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in
the page to the selected device(s).
Configure Parameters for Door

After adding the access control device, you can configure its access point parameters.
Steps
2. Select an access control device on the left panel, and then click to show the doors of the
selected device.
3. Select a door to show its parameters on the right page.
4. Edit the door or floor parameters.
79
Note
• The displayed parameters may vary for different access control devices.
Name
Edit the card reader name as desired.
Door Contact
You can set the door sensor as remaining closed or remaining open. Usually, it is remaining
closed.
Exit Button Type
You can set the exit button as remaining closed or remaining open. Usually, it is remaining
open.
Door Locked Time
After swiping the normal card and relay action, the timer for locking the door starts working.
Door Open Timeout Alarm
The alarm can be triggered if the door has not been closed in a configured time period. If it is
set as 0, no alarm will be triggered.
Super Password
The specific person can open the door by inputting the super password.
Extended Open Duration
The door contact can be enabled with appropriate delay after person with extended access
needs swipes her/his card.
Duress Code
The door can open by inputting the duress code when there is duress. At the same time, the
client can report the duress event.
Dismiss Code
Create a dismiss code which can be used to stop the buzzer of the card reader (by entering
the dismiss code on the keypad).
Note
• The duress code, super code, and dismiss code should be different.
• The duress code, super password, and the dismiss code should be different from the
authentication password.
• The length of duress code, super password, and the dismiss code is according the device,
usually it should contains 4 to 8 digits.
5. Click OK.
80
6. Optional: Click Copy to , and then select the door to copy the parameters in the page to the
selected doors.
Note
The door's status duration settings will be copied to the selected door as well.
Configure Parameters for Card Reader

After adding the access control device, you can configure its card reader parameters.
Steps
2. In the device list on the left, click to expand the door, select a card reader and you can edit
the card reader's parameters on the right.
3. Edit the card reader basic parameters in the Basic Information page.
Note
• The displayed parameters may vary for different access control devices. There are part of
parameters listed as follows. Refer to the user manual of the device for more details.
Name
Minimum Card Swiping Interval
If the interval between card swiping of the same card is less than the set value, the card
swiping is invalid. You can set it as 0 to 255.
Alarm of Max. Failed Attempts
Enable to report alarm when the card reading attempts reach the set value.
Max. Times of Card Failure
Set the max. failure attempts of reading card.
Card Reader Type/Card Reader Description
Get card reader type and description. They are read-only.
Default Authentication Mode
View the default card reader authentication mode.
Fingerprint Capacity
View the maximum number of available fingerprints.
Existing Fingerprint Number
View the number of existed fingerprints in the device.
81
4. Click Advanced and you can configure more parameters.

Enable Card Reader
Enable the function and you can operate the functions below on the card reader.
OK LED Polarity/Error LED Polarity/Buzzer Polarity
Set OK LED Polarity/Error LED Polarity/Buzzer LED Polarity of main board according to the
card reader parameters. Generally, adopts the default settings.
Max. Interval When Entering PWD
When you inputting the password on the card reader, if the interval between pressing two
digits is larger than the set value, the digits you pressed before will be cleared automatically.
Tampering Detection
Enable the anti-tamper detection for the card reader.
Fingerprint Recognition Level
Select the fingerprint recognition level from the drop-down list.
Fingerprint Recognition Interval
Select the fingerprint recognition interval from the drop-down list.
5. Click OK.
6. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page
to the selected card reader(s).
Configure Parameters for Alarm Output

After adding the access control device, if the device links to alarm outputs, you can configure the
parameters.
Before You Start
Add access control device to the client, and make sure the device supports alarm output.
Steps
1. Click Access Control → Advanced Function → Device Parameter to enter access control
parameter configuration page.
2. In the device list on the left, click to expand the door, select an alarm input and you can edit
the alarm input's parameters on the right.
3. Set the alarm output parameters.
Name
Alarm Output Active Time
How long the alarm output will last after triggered.
4. Click OK.
5. Optional: Set the switch on the upper right corner to ON to trigger the alarm output.
82
8.5.2 Configure Remaining Open/Closed

You can set the status of the door as open or closed. For example, you can set the door remaining
closed in the holiday, and set the door remaining open in the specified period of the work day.
Before You Start
Add the access control devices to the system.
Steps
1. Click Access Control → Advanced Function → Remain Open/Closed to enter the Remain Open/
Closed page.
2. Select the door that need to be configured on the left panel.
3. To set the door status during the work day, click the Week Schedule and perform the following
operations.
1) Click Remain Open or Remain Closed.
Note
Up to 8 time durations can be set to each day in the week schedule.
4) Click Save.
Related Operations
Copy to Whole Select one duration on the time bar, click Copy to Whole Week to copy
Week all the duration settings on this time bar to other week days.
Delete Selected Select one duration on the time bar, click Delete Selected to delete this
duration.
Clear Click Clear to clear all the duration settings in the week schedule.
4. To set the door status during the holiday, click the Holiday and perform the following
operations.
1) Click Remain Open or Remain Closed.
2) Click Add.
3) Enter the start date and end date.
83
Note
Up to 8 time durations can be set to one holiday period.
5) Perform the following operations to edit the time durations.
6) Optional: Select the time duration(s) that need to be deleted, and then click in the
Operation column to delete the selected time duration(s).
7) Optional: Click in the Operation column to clear all the time duration(s) in the time bar.
8) Optional: Click in the Operation column to delete this added holiday period from the
holiday list.
9) Click Save.
5. Optional: Click Copy to to copy the door status settings of this door to other door(s).
8.5.3 Configure Custom Wiegand Rule

Based on the knowledge of uploading rule for the third party Wiegand, you can set multiple
customized Wiegand rules to communicate between the device and the third party card readers.
Before You Start
Wire the third party card readers to the device.
Steps
Note
• By default, the device disables the custom wiegand function. If the device enables the custom
Wiegand function, all wiegand interfaces in the device will use the customized wiegand protocol.
• Up to 5 custom Wiegands can be set.
• For details about the custom Wiegand, see Custom Wiegand Rule Descriptions.
1. Click Access Control → Advanced Function → Custom Wiegand to enter the Custom Wiegand
page.
2. Select a custom Wiegand on the left.
3. Create a Wiegand name.
Note
Up to 32 characters are allowed in the custom Wiegand name.
4. Click Select Device to select the access control device for setting the custom wiegand.
5. Set the parity mode according to the property of the third party card reader.
84
Note
• Up to 80 bits are allowed in the total length.
• The odd parity start bit, the odd parity length, the even parity start bit and the even parity
length range from 1 to 80 bit.
• The start bit of the card ID, the manufacturer code, the site code, and the OEM should range
from 1 to 80 bit.
6. Set output transformation rule.

1) Click Set Rule to open the Set Output Transformation Rules window.
Figure 8-2 Set Output Transformation Rule

2) Select rules on the left list.
The selected rules will be added to the right list.
3) Optional: Drag the rules to change the rule order.
4) Click OK.
5) In the Custom Wiegand tab, set the rule's start bit, length, and the decimal digit.
7. Click Save.
8.5.4 Configure Card Reader Authentication Mode and Schedule

You can set the passing rules for the card reader of the access control device according to your
actual needs.
85
Steps
1. Click Access Control → Advanced Function → Authentication to enter the authentication mode
configuration page.
2. Select a card reader on the left to configure.
3. Set card reader authentication mode.
1) Click Configuration.
Figure 8-3 Select Card Reader Authentication Mode
Note
PIN refers to the PIN code set to open the door. Refer to Configure Access Control
Information .
2) Check the modes in the Available Mode list and they will be added to the selected modes
list.
3) Click OK.
After selecting the modes, the selected modes will display as icons with different color.
4. Click the icon to select a card reader authentication mode, and drag the cursor to draw a color
bar on the schedule, which means in that period of time, the card reader authentication is valid.
5. Repeat the above step to set other time periods.
86
Figure 8-4 Set Authentication Modes for Card Readers

6. Optional: Select a configured day and click Copy to Week to copy the same settings to the
whole week.
7. Optional: Click Copy to to copy the settings to other card readers.
8. Click Save.
8.5.5 Configure Other Parameters

After adding the access control device, you can set its parameters such as network parameters,
capture parameters, RS-485 parameters, Wiegand parameters, etc.
Set Network Parameters

After adding the access control device, you can set the device log uploading mode, and create
EHome account via wired network.
Set Log Uploading Mode

You can set the mode for the device to upload logs via ISUP protocol.
Steps
Note
Make sure the device is not added by ISUP.
1. Enter the Access Control module.
2. On the navigation bar on the left, enter Advanced Function → More Parameters .
3. Select an access control device in the device list and enter Network → Uploading Mode .
4. Select the center group from the drop-down list.
87
5. Check Enable to enable to set the uploading mode.

6. Select the uploading mode from the drop-down list.
- Enable N1 or G1 for the main channel and the backup channel.
- Select Close to disable the main channel or the backup channel
Note
• The main channel and the backup channel cannot enable N1 or G1 at the same time.
• N1 refers to wired network and G1 refers to GPRS.
7. Click Save.
Create EHome Account in Wired Communication Mode

You can set the account for EHome protocol in wired communication mode. Then you can add
devices via EHome protocol.
Steps
Note
• This function should be supported by the device.
• Make sure the device is not added by EHome.

3. Select an access control device in the device list and enter Network → Network Center .
4. Select the center group from the drop-down list.
5. Select the Address Type as IP Address or Domain Name.
6. Enter IP address or domain name according to the address type.
7. Enter the port number for the protocol.
Note
The port number of the wireless network and wired network should be consistent with the port
number of EHome.
8. Select the Protocol Type as EHome and select EHome version.
Note
If set the EHome version as 5.0, you should create an EHome key for the EHome account.
9. Set an account name for the network center.
10. Click Save.
88
Enable M1 Card Encryption

M1 card encryption can improve the security level of authentication.
Steps
Note
The function should be supported by the access control device and the card reader.
3. Select an access control device in the device list and click M1 Card Encryption Verification to
enter the M1 Card Encryption Verification page.
4. Set the switch to on to enable the M1 card encryption function.
5. Set the sector ID.
Note
• The sector ID ranges from 1 to 100.
• By default, Sector 13 is encrypted. It is recommended to encrypt sector 13.
6. Click Save to save the settings.
Set RS-485 Parameters

You can set the access control device's RS-485 parameters including the baud rate, data bit, the
stop bit, parity type, flow control type, communication mode, work mode, and connection mode.
Before You Start
Add access control device to the client, and make sure the device supports RS-485 interface.
Steps
3. Select an access control device in the device list and click RS-485 to enter the RS-485 Settings
page.
4. Select the serial port number from the drop-down list to set the RS-485 parameters.
5. Set the baud rate, data bit, the stop bit, parity type, communication mode, working mode, and
connection mode in the drop-down list.
Note
When the connection mode is Connect Access Control Device, you can select Card No. or
Person ID as the output type.
6. Click Save.
89
• The configured parameters will be applied to the device automatically.

• When you change the working mode or connection mode, the device will reboot
automatically.
Set Wiegand Parameters

You can set the access control device's Wiegand channel and the communication mode. After
setting the Wiegand parameters, the device can connect to Wiegand card reader via Wiegand
communication.
Steps
Note
3. Select an access control device in the device list and click Wiegand to enter the Wiegand
Settings page.
4. Set the switch to on to enable the Wiegand function for the device.
5. Select the Wiegand channel No. and the communication mode from the drop-down list.
Note
If you set Communication Direction as Sending, you are required to set the Wiegand Mode as
Wiegand 26, Wiegand 34, Wiegand 27, or Wiegand 35.
6. Click Save.
• The configured parameters will be applied to the device automatically.
• After changing the communication direction, the device will reboot automatically.
8.6 Configure Linkage Actions for Access Control

You can configure different linkage actions for the event detected by the access control device.
After that, linkage actions will be triggered once the event happens. This mechanism is used for
notifying the security personnel the event, or triggering automatic access control in real time.
Two types of linkage actions are supported:
• Client Actions: When the event is detected, it will trigger the actions on the client, such as the
client making an audible warning..
• Device Actions: When the event is detected, it will trigger the actions of a specific device, such
as buzzing of a card reader and, opening/closing of a door, ..
90
8.6.1 Configure Client Actions for Access Event

Even if you are far away from an access point, you can still know what happens and how urgent the
event is by configuring linked actions of access event on the client. You will be notified on the client
once an event is triggered, so that you can response to the event instantly. You can also configure
client actions of access points in a batch at a time.
Steps
Note
The linkage actions here refer to the linkage of the client software's own actions such as audible
warning, email linkage, etc.
1. Click Event Management → Access Control Event .
The added access control devices will display in the device list.
2. Select a resource (including device, alarm input, door/elevator, and card reader) from the device
list.
The event types which the selected resource supports will display.
3. Select the event(s) and click Edit Priority to define the priority for the event(s), which can be
used to filter events in the Event Center.
4. Set the linkage actions of the event.
1) Select the event(s) and click Edit Linkage to set the client actions when the events triggered.
Audible Warning
The client software gives an audible warning when alarm is triggered. You can select the
alarm sound for audible warning.
Note
For setting the alarm sound, please refer to Set Alarm Sound in the user manual of client
software..
Send Email
Send an email notification of the alarm information to one or more receivers.
For details about setting email parameters, refer to Set Email Parameters in the user
manual of client software..
2) Click OK.
5. Enable the event so that when the event is detected, en event will be sent to the client and the
linkage actions will be triggered.
6. Optional: Click Copy to... to copy the event settings to other access control device, alarm input,
door, or card reader.
91
8.6.2 Configure Device Actions for Access Event

You can set the access control device's linkage actions for the access control device's triggered
event. When the event is triggered, it can trigger the alarm output, host buzzer, and other actions
on the same device.
Steps
Note
It should be supported by the device.
1. Click Access Control → Linkage Configuration .
2. Select the access control device from the list on the left.
3. Click Add button to add a new linkage.
4. Select the event source as Event Linkage.
5. select the event type and detailed event to set the linkage.
6. In the Linkage Target area, set the property target to enable this action.
Buzzer on Controller
The audible warning of access control device will be triggered.
7. Click Save.
8. Optional: After adding the device linkage, you can do one or more of the following:
Edit Linkage Select the configured linkage settings in the device list and you can edit
Settings its event source parameters, including event source and linkage target.
Delete Linkage Select the configured linkage settings in the device list and click Delete
Settings to delete it.
8.6.3 Configure Device Actions for Card Swiping

You can set the access control device's linkage actions for the specified card swiping. When you
swipe the specified card, it can trigger the alarm output, host buzzer, and other actions on the
same device.
Steps
Note
4. Select the event source as Card Linkage.
5. Enter the card number or select the card from the dropdown list.
6. Select the card reader where the card swipes to trigger the linked actions.
92
Buzzer on Reader
The audible warning of card reader will be triggered.
8. Click Save.
When the card (configured in Step 5) swipes on the card reader (configured in Step 6), it can
trigger the linked actions (configured in step 7).
8.6.4 Configure Device Actions for Person ID

You can set the access control device's linkage actions for the specified person ID. When access
control device detects the specified person ID, it can trigger the alarm output, host buzzer, and
other actions on the same device.
Steps
Note
4. Select the event source as Person Linkage.
5. Enter the employee number or select the person from the dropdown list.
6. Select the card reader where the card swipes to trigger the linked actions.
Buzzer on Reader
The audible warning of card reader will be triggered.
8. Click Save.
93
8.7 Door Control

In Monitoring module, you can view the real-time status of the doors managed by the added
access control device. You can also control the doors such as open/close the door, or remain the
door open/closed via the client remotely. The real-time access event are displayed in this module.
You can view the access details and person details.
Note
For the user with door control permission, the user can enter the Monitoring module and control
the door. Or the icons used for control will not show. For setting the user permission, refer to
Person Management .
8.7.1 Control Door Status

You can control the status for a single door, including opening door, closing door, remaining the
door open, and remaining the door closed.
Steps
1. Click Monitoring to enter the status monitoring page.
2. Select an access point group on the upper-right corner.
Note
For managing the access point group, refer to Group Management in the user manual of the
client software.
The doors in the selected access control group will display.
3. Click a door icon to select a door, or press Ctrl and select multiple doors.
4. Click the following buttons to control the door.
Open Door
When the door is locked, unlock it and it will be open for once. After the open duration, the
door will be closed and locked again automatically.
Close Door
When the door is unlocked, lock it and it will be closed. The person who has the access
authorization can access the door with credentials.
Remain Open
The door will be unlocked (no matter closed or open). All the persons can access the door
with no credentials required.
94
Remain Closed
The door will be closed and locked. No person can access the door even if he/she has the
authorized credentials, except the super users.
Capture
Capture a picture manually.
Note
The Capture button is available when the device supports capture function. The picture is
saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in
the user manual of the client software.
Result
The icon of the doors will change in real-time according to the operation if the operation is
succeeded.
8.7.2 Check Real-Time Access Records

The access records will display in real time, including card swiping records, fingerprint comparison
records, etc. You can view the person information and view the picture captured during access.
Steps
1. Click Monitoring and select a group from the drop-down list on the upper-right corner.
The access records triggered at the doors in the selected group will display in real time. You can
view the details of the records, including card No., person name, organization, event time, etc.
2. Optional: Check the event type and event status so that these events will show in the list if the
events are detected. The events of unchecked type or status will not be displayed in the list.
3. Optional: Check Show Latest Event and the latest access record will be selected and displayed
at the top of the record list.
4. Optional: Click the event to view the accessed person details, including person pictures
(captured picture and profile), person No., person name, organization, phone, contact address,
etc.
Note
You can double click the captured picture to enlarge it to view the details.
5. Optional: Right click on the column name of the access event table to show or hide the column
according to actual needs.
95
8.8 Event Center

You can configure the event of the added resources and set the linkage actions so that when the
event is triggered, the software client can notify the security personnel and record the event
details for checking afterwards.
In the event management page, you can configure access control event. For details about access
control event configuration, refer to Configure Linkage Actions for Access Control .
In the event center, you can view the real-time events and search the historical events. For details,
refer to View Real-Time Events and Search Historical Events .
8.8.1 Enable Receiving Events from Devices

Before the client can receive the event information from the device, you need to arm the device
first.
Steps
1. Click → Tool → Device Arming Control open Device Arming Control page.
All the added devices display on this page.
2. In the Operation column, turn on the switch to enable auto-arming, or click Arm All to arm all
the devices.
Figure 8-5 Device Arming Control

3. View the arming status of each device in the Arming Status column.
Result
The events of armed device(s) are automatically uploaded to the client when the event is
triggered.
96
8.8.2 View Real-Time Events

In the Real-time Event module of the event center page, you can view the real-time event
information, including event source, event time, priority, event key words, etc.
Before You Start
Enable receiving events from devices before the client can receive event information from the
device, see Enable Receiving Events from Devices for details.
Steps
1. Click Event Center → Real-time Event to enter the real-time event page and you can view the
real-time events received by the client.
Event Time
For video device, event time is the client time when it receives the event. For none-video
device, event time is the time when the event is triggered.
Figure 8-6 View Real-Time Events

2. Set the filter conditions or enter the event key word in the Filter text field to display the
required events only.
Device Type
The type of device that occurred the event.
Priority
The priority of the event that indicates the urgent degree of the event.
3. Optional: Right click the table header of the event list to customize the event related items to
be displayed in the event list.
97
Figure 8-7 Customize Event Related Items to be Displayed

4. View the event information details.
1) Select an event in the event list.
2) Click Expand in the right-lower corner of the page.
3) View the related picture, detail description and handing records of the event.
4) Optional: Hover the cursor on the related picture, and then click the download icon on the
upper-right corner of the picture to download it to the local PC. You can set the saving path
manually.
5. Optional: Perform the following operations if necessary.
Handle Single Event Click Handle to enter the processing suggestion, and then click
Commit.
Note
After an event is handled, the Handle button will become Add
Remark, click Add Remark to add more remarks for this handled
event.
Handle Events in a Select events that need to be processed, and then click Handle in
Batch Batch. Enter the processing suggestion, and then click Commit.
Enable/Disable Click Enable Audio/Disable Audio to enable/disable the audio of
Alarm Audio the event.
Select the Latest Check Auto-Select Latest Event to select the latest event
Event Automatically automatically and the event information details is displayed.
Clear Events Click Clear to clear the all the events in the event list.
Send Email Select an event and then click Send Email, and the information
details of this event will be sent by email.
98
Note
You should configure the email parameters first, see Set Email
Parameters in the user manual of client software for details.
8.8.3 Search Historical Events

In the Event Search module of the event center page, you can search the historical events via time,
device type, and other conditions according to the specified device type, and then process the
events.
Before You Start
Enable receiving events from devices before the client can receive event information from the
device,see Enable Receiving Events from Devices for details.
Steps
1. Click Event Center → Event Search to enter the event search page.
Figure 8-8 Search History Event

2. Set the filter conditions to display the required events only.
Time
The client time when the event starts.
Search by
Group: Search the events occurred on the resources in the selected group.
Device: Search the events occurred on the selected device.
Device Type
The type of device that occurred the event.
99
All
All the device types, and you can set the following filter conditions: group, priority, and
status.
Video Intercom
For the events of video intercom, you need to select searching scope: All Record and Only
Unlocking.
• All Records: You can filter the events from all the video intercom events, and you need
to set the following filter conditions: device, priority, status.
• Only Unlocking: You can filter the events from all the video intercom unlocking events,
and you need to set the following filter conditions: device, unlocking type.
Access Control
For the events of access control, you can set the following filter conditions: device,
priority, status, event type, card reader type, person name, card no., organization.
Note
Click Show More to set the event type, card reader type, person name, card no.,
organization.
Group
The group of the device that occurred the event. You should set the group as condition only
when you select the Device Type as All.
Device
The device that occurred the event.
Priority
The priority including low, medium, high and uncategorized which indicates the urgent
degree of the event.
Status
The handling status of the event.
3. Click Search to search the events according the conditions you set.
4. Optional: Right click the table header of the event list to customize the event related items to
be displayed in the event list.
100
Figure 8-9 Customize Event Related Items to be Displayed

5. Optional: Handle the event(s).
- Handle single event: Select one event that need to be processed, and then click Handle in
the event information details page, and enter the processing suggestion.
- Handle events in a batch: Select the events which need to be processed, and then click
Handle in Batch, and enter the processing suggestion.
Note
After an event is handled, the Handle button will become Add Remark, click Add Remark to add
more remarks for this handled event.
6. Optional: Select an event and then click Send Email, and the information details of this event
will be sent by email.
Note
You should configure the email parameters first, see Set Email Parameters in the user manual of
client software for details.
7. Optional: Click Export to export the event log or event pictures to the local PC in CSV format.
You can set the saving path manually.
8. Hover the cursor on the related picture, and then click the download icon on the upper-right
corner of the picture to download it to the local PC. You can set the saving path manually.
101
8.9 Time and Attendance

The Time and Attendance module provides multiple functionalities to track and monitor when
employees start and stop work, and full control of employees working hours such as late arrivals,
early departures, time taken on breaks and absenteeism.
Note
In this section, we introduce the configurations before you can getting the attendance reports. The
access records recorded after these configurations will be calculated in the statistics.
8.9.1 Configure Attendance Parameters

You can configure the attendance parameters, including the general rule, overtime parameters,
attendance check point, holiday, leave type, etc.
Set Weekend
The days of weekends may vary in different countries and regions. The client provides weekends
definition function. You can select one or more days as the weekends according to actual
requirements, and set different attendance rules for weekends from workdays.
Steps
Note
The parameters configured here will be set as default for the newly added time period. It will not
affect the existed one(s).
1. Enter Time & Attendance module.
2. Click Attendance Settings → General Rule .
3. Select the day(s) as weekend, such as Saturday and Sunday.
4. Click Save.
Configure Overtime Parameters

You can configure the overtime parameters for workday and weekend, including overtime level,
work hour rate, attendance status for overtime, etc.
Steps
1. Click Time & Attendance → Attendance Settings → Overtime .
2. Set required information.
Overtime Level for Workday
102
When you work for a certain period after end-work time on workday, you will reach different
overtime level: overtime level 1, overtime level 2 and overtime level 3. You can set different
work hour rate for three overtime levels, respectively.
Work Hour Rate
Work Hour Rate is used to calculate work hours by multiplying it by overtime. When you
work for a certain period after end-work time on workday, you will reach different overtime
level. You can set different work hour rates (1-10, can be a decimal) for three overtime levels.
For example, your valid overtime is one hour (in overtime level 1), and the work hour rate of
overtime level 1 is set as 2, then the work hours in the period will be calculated as 2 hours.
Overtime Rule for Weekend
You can enable overtime rule for weekend and set calculation mode.
3. Click Save.
Configure Attendance Check Point

You can set the card reader(s) of the access point as the attendance check point, so that the
authentication on the card readers will be recorded for attendance .
Before You Start
You should add access control device before configuring attendance check point. For details, refer
to Add Device .
Steps
Note
By default, all card readers of the added access control devices are set as attendance checkpoint.
1. Enter the Time & Attendance module.
2. Click Attendance Settings → Attendance Check Point to enter the Attendance Check Point
Settings page.
3. Optional: Set Set All Card Readers as Check Points switch to off.
Only the card readers in the list will be set as the attendance check points.
4. Check the desired card reader(s) in the device list as attendance check point(s).
5. Set check point function as Start/End-Work, Start-Work or End-Work.
6. Click Set as Check Point.
The configured attendance check point displays on the right list.
Configure Holiday
You can add the holiday during which the check-in or check-out will not be recorded.
103
Add Regular Holiday

You can configure a holiday which will take effect annually on regular days during the effective
period, such as New Year's Day, Independence Day, Christmas Day, etc.
Steps
2. Click Attendance Settings → Holiday to enter the Holiday Settings page.
3. Check Regular Holiday as holiday type.
4. Custom a name for the holiday.
5. Set the first day of the holiday.
6. Enter the number of the holiday days.
7. Set the attendance status if the employee works on holiday.
8. Optional: Check Repeat Annually to make this holiday setting effective every year.
9. Click OK.
The added holiday will display in the holiday list and calendar.
If the date is selected as different holidays, it will be recorded as the first-added holiday.
10. Optional: After adding the holiday, perform one of the following operations.
Edit Holiday Click to edit the holiday information.
Delete Holiday Select one or more added holidays, and click Delete to delete the
holiday(s) from the holiday list.
Add Irregular Holiday

You can configure a holiday which will take effect annually on irregular days during the effective
period, such as Bank Holiday.
Steps
2. Click Attendance Settings → Holiday to enter the Holiday Settings page.
3. Click Add to open the Add Holiday page.
4. Check Irregular Holiday as holiday type.
5. Custom a name for the holiday.
6. Set the start date of the holiday.
Example
If you want to set the forth Thursday in November, 2019 as the Thanksgiving Day holiday, you
should select 2019, November, 4th, and Thursday from the four drop-down lists.
7. Enter the number of the holiday days.
8. Set the attendance status if the employee works on holiday.
9. Optional: Check Repeat Annually to make this holiday setting effective every year
10. Click OK.
104
The added holiday will display in the holiday list and calendar.
If the date is selected as different holidays, it will be recorded as the first-added holiday.
11. Optional: After adding the holiday, perform one of the following operations.
Edit Holiday Click to edit the holiday information.
Delete Holiday Select one or more added holidays, and click Delete to delete the
holiday(s) from the holiday list.
Configure Leave Type

You can customize the leave type (major leave type and minor leave type) according to actual
needs. You can also edit or delete the leave type.
Steps
2. Click Attendance Settings → Leave Type to enter the Leave Type Settings page.
3. Click Add on the left to add a major leave type.
4. Optional: Perform one of the following operations for major leave type.
Edit Move the cursor over the major leave type and click to edit the major leave
type.
Delete Select one major leave type and click Delete on the left to delete the major leave
type.
5. Click Add on the right to add a minor leave type.
6. Optional: Perform one of the following operations for minor leave type.
Edit Move the cursor over the minor leave type and click to edit the minor leave
type.
Delete Select one or multiple major leave types and click Delete on the right to delete the
selected minor leave type(s).
Synchronize Authentication Record to Third-Party Database

The attendance data recorded in client software can be used by other system for calculation or
some other operations. You can enable synchronization function to apply the authentication record
from client software to the third-party database automatically.
Steps
2. Click Attendance Settings → Third-Party Database .
3. Set Apply to Database switch to on to enable synchronization function.
4. Select database Type as SQLServer or MySql.
105
Note
If you select MySql, you should import the configuration file (libmysql.dll) from local PC.
5. Set the other required parameters of the third-party database, including server IP address,
database name, user name and password.
6. Set table parameters of database according to the actual configuration.
1) Enter the table name of the third-party database.
2) Set the mapped table fields between the client software and the third-party database.
7. Click Save to test whether database can be connected and save the settings for the successful
connection.
• The attendance data will be written to the third-party database.
• During synchronization, if the client disconnects with the third-party database, the client will
start reconnection every 30 mins. After being reconnected, the client will synchronize the
data recorded during the disconnected time period to the third-party database.
Configure Break Time

You can add break time and set start time, end time, duration, calculation mode and other
parameters for the break. The added break time can also be edited or deleted.
Steps
1. Click Time & Attendance → Timetable .
The added timetables are displayed in the list.
2. Select an added timetable or click Add to enter setting timetable page.
3. Click Break Time to enter Break Time page.
4. Click Break Time Settings.
5. Add break time.
1) Click Add.
2) Enter a name for the break time.
3) Set related parameters for the break time.
Start Time / End Time
Set the time when the break starts and ends.
No Earlier Than / No Later Than
Set the earliest swiping time for starting break and the latest swiping time for ending
break.
Break Duration
The duration from start time to end time of the break.
Calculation
Auto Deduct
106
The fixed break duration will be excluded from work hours.

Must Check
The break duration will be calculated and excluded from work hours according to
actual check-in and check-out time.
Note
If you select Must Check as calculation method, you need to set attendance status for
late or early returning from break.
6. Click Save to save the settings.
7. Optional: Click Add to continue adding break time.
Configure Report Display

You can configure display contents displayed in the attendance report, such as the company name,
logo, date format, time format, and mark.
Steps
2. Click Attendance Statistics → Report Display .
3. Set the display settings for attendance report.
Company Name
Enter a company name to display the name in the report.
Attendance Status Mark
Enter the mark and select the color. The related fields of attendance status in the report will
display with the mark and color.
Weekend Mark
Enter the mark and select the color. The weekend fields in the report will display with the
mark and color.
4. Click Save.
8.9.2 Add General Timetable

On the timetable page, you can add general timetable for employees, which requires the fixed
start-work time and end-work time. Also, you can set valid check-in/out time, allowable timetable
for being late and leaving early.
Steps
1. Click Time and Attendance → Timetable to enter the timetable settings page.
2. Click Add to enter add timetable page.
107
Figure 8-10 Add Timetable

3. Create a name for the timetable.
Note
You can click the color icon beside the name to customize the color for the valid timetable on
the time bar in the Configuration Result area.
4. Select the timetable type as general.
5. Select calculation method.
First In & Last Out
The first check-in time is recorded as start work time and the last check-out time is recorded
as the end-work time.
Each Check-In/Out
Each check-in time and check-out time is valid and the sum of all periods between adjacent
check-in and check-out time will be recorded as the valid working duration.
You need to set Valid Authentication Interval for this calculation method. For example, if the
interval between card swiping of the same card is less than the set value, the card swiping is
invalid.
6. Optional: Set Enable T&A Status switch to on to calculate according to attendance status of the
device.
108
Note
7. Set the related attendance time parameters as the following:
Start/End-Work Time
Set the start-work time and end-work-time.
Valid Check-in/out Time
On the time bar, adjust the yellow bar to set the timetable during which the check-in or
check-out is valid.
Calculated as
Set the duration calculated as the actual work duration.
Late/Early Leave Allowable
Set the timetable for late or early leave.
8. Set absence related parameters.
Check-In, Late for
You can set the late time duration for the employee who has checked in but is late for work.
If the employee exceeds the required time period, his/her attendance data will be marked as
absent.
Check-Out, Early Leave for
You can set the early leave time duration for the employee who checks out earlier than the
normal leave time, and his/her attendance data will be marked as absent.
No Check-in
If the employee does not check in, his/her attendance data may be marked as absent or late.
No Check-Out
If the employee does not check out, his/her attendance data may be marked as absent or
early leave.
9. Click Save to add the timetable.
10. Optional: Perform one or more following operations after adding timetable.
Edit Timetable Select a timetable from the list to edit related information.
Delete Timetable Select a timetable from the list and click Delete to delete it.
8.9.3 Add Shift

You can add shift for employees including setting shift period (day, week, month) and the effective
attendance time. According to the actual requirements, you can adding multiple timetables in one
shift for employees, which requires them to check in and check out for each timetable.
109
Before You Start

Add a timetable first. See Add General Timetable for details.
Steps
1. Click Time & Attendance → Shift to enter shift settings page.
2. Click Add to enter Add Shift page.
3. Enter the name for shift.
4. Select the shift period from the drop-down list.
5. Select the added timetable and click on the time bar to apply the timetable.
Figure 8-11 Add Shift
Note
You can select more than one timetables. The start and end work time and the valid check-in
and out time in different time tables can not be overlapped.
110
Figure 8-12 Add Multiple Timetables

6. Click Save.
The added shift lists on the left panel of the page. At most 64 shifts can be added.
7. Optional: Assign the shift to organization or person for a quick shift schedule.
1) Click Assign.
2) Select Organization or Person tab and check the desired organization(s) or person(s) box.
The selected organizations or persons will list on the right page.
3) Set the Expire Date for the shift schedule.
4) Set other parameters for the schedule.
Check-in Not Required
Persons in this schedule do not need to check-in when they come to work.
Check-out Not Required
Persons in this schedule do not need to check-out when they end work.
Scheduled on Holidays
On the holidays, this schedule is still effective and the persons needs to go to work
according to the schedule.
Effective for Overtime
The persons' overtime will be recorded for this schedule.
5) Click Save to save the quick shift schedule.
111
8.9.4 Manage Shift Schedule

Shift work is an employment practice designed to make use of all 24 hours of the clock each day of
the week. The practice typically sees the day divided into shifts, set periods of time during which
different shifts perform their duties.
You can set department schedule, person schedule, and temporary schedule.
Set Department Schedule

You can set the shift schedule for one department, and all the persons in the department will be
assigned with the shift schedule.
Before You Start
In Time & Attendance module, the department list is the same with the organization. You should
add organization and persons in Person module first. See Person Management for details.
Steps
1. Click Time & Attendance → Shift Schedule to enter the Shift Schedule Management page.
2. Click Department Schedule to enter Department Schedule page.
3. Select the department from the organization list on the left.
Note
If Include Sub Organization is checked, when selecting the organization, its sub organizations
are selected at the same time.
4. Select the shift from the drop-down list.
5. Optional: Enable Multiple Shift Schedules and select the effective time period(s) from the
added timetables for the persons.
Note
This is only available for shift with only one timetable.
Multiple Shift Schedules
It contains more than one timetables. The person can check in/out in any of the timetables
and the attendance will be effective.
If the multiple shift schedules contains three timetables: 00:00 to 07:00, 08:00 to 15:00 and
16:00 to 23:00. The attendance of the person adopting this multiple shift schedules will be
effective in any of the three timetables. If the person checks in at 07:50, it will apply the
nearest timetable 08:00 to 15:00 to the person's attendance.
6. Set the start date and end date.

7. Set other parameters for the schedule.
112
On the holidays, this schedule is still effective and the persons needs to go to work according
to the schedule.
8. Click Save.
Set Person Schedule

You can assign the shift schedule to one or more persons. You can also view and edit the person
schedule details.
Before You Start
Add department and person in Person module. See Person Management for details.
Steps
Note
The person schedule has the higher priority than department schedule.
1. Click Time & Attendance → Shift Schedule to enter the Shift Schedule page.
2. Click Person Schedule to enter Person Schedule page.
3. Select the organization and select the person(s).
4. Select the shift from the drop-down list.
5. Optional: Enable Multiple Shift Schedules and select the effective time period(s) from the
added timetables for the persons.
Note
This is only available for shift with only one timetable.
Multiple Shift Schedules
6. Set the start date and end date.

7. Set other parameters for the schedule.
113

On the holidays, this schedule is still effective and the persons needs to go to work according
to the schedule.
8. Click Save.
Set Temporary Schedule

You can add a temporary schedule for the person and the person will be assigned with the shift
schedule temporarily. You can also view and edit the temporary schedule details.
Before You Start
Add department and person in Person module. See Person Management for details.
Steps
Note
The temporary schedule has higher priority than department schedule and person schedule.
2. Click Temporary Schedule to enter Temporary Schedule page.
3. Select the organization and select the person(s).
4. Click one date or click and drag to select multiple dates for the temporary schedule.
5. Select Workday or Non-Workday from drop-down list.
If Non-Workday is selected, you need to set the following parameters.
Calculated as
Select normal or overtime level to mark the attendance status for temporary schedule.
Timetable
Select a timetable from drop-down list.
Multiple Shift Schedule
114
Rule
Set other rule for the schedule, such as Check-in Not Required, andCheck-out Not Required.
6. Click Save.
Check Shift Schedule

You can check the shift schedule in calendar or list mode. You ca also edit or delete the shift
schedule.
Steps
2. Select the organization and corresponding person(s).
3. Click or to view the shift schedule in calendar or list mode.
Calendar
In calendar mode, you can view the shift schedule for each day in one month. You can click
the temporary schedule for one day to edit or delete it.
List
In list mode, you can view the shift schedule details about one person or organization, such
as shift name, type, effective period and so on. Check the shift schedule(s), and click Delete
to delete the selected shift schedule(s).
8.9.5 Manually Correct Check-in/out Record

If the attendance status is not correct, you can manually correct the check-in or check out record.
You can also edit, delete, search, or export the check-in or check-out record.
Before You Start
• You should add organizations and persons in Person module. For details, refer to Person
Management .
• The person's attendance status is incorrect.
Steps
1. Click Time & Attendance → Attendance Handling to enter attendance handling page.
2. Click Correct Check-In/Out to enter adding the check-in/out correction page.
3. Select person from left list for correction.
4. Select the correction date.
5. Set the check-in/out correction parameters.
- Select Check-in and set the actual start-work time.
- Select Check-out and set the actual end-work time.
115
Note
You can click to add multiple check in/out items. At most 8 check-in/out items can be
supported.
6. Optional: Enter the remark information as desired.
7. Click Save.
8. Optional: After adding the check-in/out correction, perform one of the following operations.
View Click or to view the added attendance handling information in calendar or list
mode.
Note
In calendar mode, you need to click Calculate to get the attendance status of the
person in one month.
Edit • In calendar mode, click the related label on date to edit the details.
• In list mode, double-click the related filed in Date, Handling Type, Time, or
Remark column to edit the information.
Delete Delete the selected items.
Export Export the attendance handling details to local PC.
Note
The exported details are saved in CSV format.
8.9.6 Add Leave and Business Trip

You can add leave and business trip when the employee want to ask for leave or go on a business
trip.
Before You Start
You should add organizations and persons in the Person module. For details, refer to Person
Management .
Steps
1. Click Time & Attendance → Attendance Handling to enter attendance handling page.
2. Click Apply for Leave/Business Trip to enter adding the leave/business trip page.
3. Select person from left list.
4. Set the date(s) for your leave or business trip.
5. Select the major leave type and minor leave type from the drop-down list.
Note
You can set the leave type in Attendance Settings. For details, refer to Configure Leave Type .
116
6. Set the time for leave.

7. Optional: Enter the remark information as desired.
8. Click Save.
9. Optional: After adding the leave and business trip, perform one of the following operations.
View Click or to view the added attendance handling information in calendar or list
mode.
Note
In calendar mode, you need to click Calculate to get the attendance status of the
person in one month.
Edit • In calendar mode, click the related label on date to edit the details.
• In list mode, double-click the filed in Date, Handling Type, Time, or Remark
column to edit the related information.
Delete Delete the selected items.
Export Export the attendance handling details to local PC.
Note
The exported details are saved in CSV format.
8.9.7 Calculate Attendance Data

You need to calculate the attendance data before searching and viewing the overview of the
attendance data, employees' detailed attendance data, employees' abnormal attendance data, the
employees' overtime working data, and card swiping log.
Automatically Calculate Attendance Data

You can set a schedule so that the client can automatically calculate attendance data of the
previous day at the time you configured every day.
Steps
Note

2. Click Attendance Settings → General Rule .
3. In the Auto-Calculate Attendance area, set the time that you want the client to calculate the
data.
4. Click Save.
117
The client will calculate the attendance data of the previous day from the time you have
configured.
Manually Calculate Attendance Data

You can calculate the attendance data manually by setting the data range.
Steps
2. Click Attendance Statistics → Calculation .
3. Set the start time and end time to define the attendance data range.
4. Set other conditions, including department, name, person ID and attendance status.
5. Click Calculate.
Note
It can only calculate the attendance data within three months.
6. Perform one of the following operations.
Correct Check-in/out Click Correct Check-in/out to add check-in/out correction.
Select Items to Click , or right-click the titles of different items to select items to
Display be displayed in the report.
Generate Report Click Report to generate the attendance report.
Export Report Click Export to export attendance data to local PC.
Note
The exported details are saved in .CSV format.
8.9.8 Attendance Statistics

You can check the original attendance record, generate and export the attendance report based on
the calculated attendance data.
Get an Overview of Employees' Attendance Data

You can search and view the employee's attendance records on the client, including attendance
time, attendance status, check point, etc.
Before You Start
• You should add organizations and persons in Person module and the persons have swiped cards.
For details, refer to Person Management .
• Calculate the attendance data.
118
Note
• The client will automatically calculate the previous day's attendance data at 1:00 am on the
next day.
• Keep the client running at 1:00 am or it cannot calculate the previous day's attendance data
automatically. If not calculated automatically, you can calculate the attendance data manually.
For details, refer to Manually Calculate Attendance Data .
Steps
2. Click Attendance Statistics → Attendance Record .
3. Set the attendance start time and end time that you want to search.
4. Set other search conditions, including department, name, and person ID.
5. Select data source as Original Records on Device or Manual Handling Records.
6. Optional: Click Get Events from Device to get the attendance data from the device.
7. Optional: Click Reset to reset all the search conditions and edit the search conditions again.
8. Click Search.
The result displays on the page. You can view the employee's required attendance status and
check point.
9. Optional: After searching the result, perform one of the following operations.
Generate Report Click Report to generate the attendance report.
Export Report Click Export to export the results to the local PC.
Custom Export For details, refer to .
Generate Instant Report

It supports to generate the a series of attendance reports manually to view the employees'
attendance results.
Before You Start
Calculate the attendance data.
Note
You can calculate the attendance data manually, or set the schedule so that the client can calculate
the data automatically every day. For details, refer to Calculate Attendance Data .
Steps
2. Click Attendance Statistics → Report .
3. Select a report type.
4. Select the department or person to view the attendance report.
119
5. Set the start time and end time during which the attendance data will be displayed in the
report.
6. Click Report to generate the statistics report and open it.
Custom Attendance Report

The client supports multiple report types and you can pre-define the report content and it can
send the report automatically to the email address you configured.
Steps
Note
Set the email parameters before you want to enable auto-sending email functions. For details,
refer to Set Email Parameters in the user manual of the client software.
2. Click Attendance Statistics → Custom Report .
3. Click Add to pre-define a report.
4. Set the report content.
Report Name
Enter a name for the report.
Report Type
Select one report type and this report will be generated.
Report Time
The time to be selected may vary for different report type.
Person
Select the added person(s) whose attendance records will be generated for the report.
5. Optional: Set the schedule to send the report to the email address(es) automatically.
1) Check the Auto-Sending Email to enable this function.
2) Set the effective period during which the client will send the report on the selected sending
date(s).
3) Select the date(s) on which the client will send the report.
4) Set the time at which the client will send the report.
Example
If you set the effective period as 2018/3/10 to 2018/4/10, select Friday as the sending date,
and set the sending time as 20:00:00, the client will send the report at 8 p.m. on Fridays
during 2018/3/10 to 2018/4/10.
120
Note
Make sure the attendance records are calculated before the sending time. You can calculate
the attendance data manually, or set the schedule so that the client can calculate the data
automatically every day. For details, refer to Calculate Attendance Data .
5) Enter the receiver email address(es).
Note
You can click + to add a new email address. Up to 5 email addresses are allowed.
6) Optional: Click Preview to view the email details.
6. Click OK.
7. Optional: After adding the custom report, you can do one or more of the followings:
Edit Report Select one added report and click Edit to edit its settings.
Delete Report Select one added report and click Delete to delete it.
Generate Report Select one added report and click Report to generate the report instantly
and you can view the report details.
121
Chapter 9 Remote Configuration (Web)

Configure device parameters remotely.
9.1 View Device Information

View and set device name, view device type, serial No., version, relay number, and lock number.
Select a device from the Device for Management tab and click → System → Device Information
to enter the Device Information page.
Figure 9-1 View Device Information

You can set the device name, view the device type, serial No., version, relay number, and lock
number. Click Save to save the settings.
122
9.2 Change Device Password

You can change the device password.
Before You Start
Make sure the device is activated. For details, see Activation.
Steps
1. On the Device for Management page, click → System → User to enter the User tab.
2. Select a user and click Edit to enter the Edit page.
3. Input the old password, create a new password, and confirm the new password.
Caution
The password strength of the device can be automatically checked. We highly recommend you
change the password of your own choosing (using a minimum of 8 characters, including at least
three kinds of following categories: upper case letters, lower case letters, numbers, and special
characters) in order to increase the security of your product. And we recommend you change
your password regularly, especially in the high security system, changing the password monthly
or weekly can better protect your product.
4. Click OK.
Result
The device password is changed. You should enter the new password on the Device for
Management page to reconnect the device.
9.3 Time Management

Manage device's time zone, time synchronization, and DST parameters.
Time Zone and Time Synchronization

On the Device for Management page, select a device and click → System → Time to enter the
Time tab.
You can select a time zone, set NTP parameters, or manually synchronize time.
Time Zone
Select a time zone from the drop-down list.
NTP
The device will synchronize time with NTP automatically. After you enable NTP, you should set
the NTP server address, NTP port, and synchronization interval.
123
Manual Time Synchronization

After you enable Manual Time Synchronization, you can manually set the device time.
If you check Synchronize with Computer Time, the Set Time will display the current computer's
time. At this time, uncheck Synchronize with Computer Time, and click , you can edit the
device time manually.
Click Save to save the settings.
DST
On the Device for Management page, click Remote Configuration → System → Time → DST to
enter the DST tab.
Enable DST and you can edit the DST bias time, the DST start time, and end time.
Click Save.
9.4 System Maintenance

You can reboot the device, restore the device to the default settings, and upgrade the device.
Reboot
On the Device for Management page, click → System → System Maintenance to enter the
System Maintenance tab.
Click Reboot and the device starts rebooting.
Restore Default Settings
On the Device for Management page, click Remote Configuration → System → System
Maintenance to enter the System Maintenance tab.
Restore Default
The parameters will be restored the default ones, excluding the IP address.
Restore All
All device parameters will be restored to the default ones. The device should be activated after
restoring.
Upgrade
On the Device for Management page, click Remote Configuration → System → System
Maintenance to enter the System Maintenance tab.
Select a device type from the drop-down list, click Browse and select an upgrade file from the local
computer, and click Upgrade.
124
Note
• If you select Card reader as the device type, you should also select a card reader No. from the
drop-down list.
• The upgrade will lasts for about 2 min. Do not power off during the upgrading. After upgrading,
the device will reboot automatically.
9.5 Configure RS-485 Parameters

You can set the RS-485 parameters including the baud rate, data bit, stop bit, parity type,
communication mode, work mode, and connection mode.
Steps
1. Click Maintenance and Management → Device to enter the device list.
2. Click to enter the remote configuration page.
3. Click System → RS-485 Settings to enter the Configuring the RS-485 Parameters tab.
4. Select the serial No. of the port from the drop-down list to set the RS-485 parameters.
5. Set the baud rate, data bit, the stop bit, parity, flow control, communication mode, working
mode, and the connection mode from the drop-down list.
6. Click Save and the configured parameters will be applied to the device automatically.
Note
After changing the working mode, the device will be rebooted. A prompt will be popped up
after changing the working mode.
9.6 Security Mode Settings

Set the security mode for logging in the client software.
On the Device for Management page, click → System → Security to enter the Security Mode
tab.
Select a security mode from the drop-down list, and click Save.
You can also enable SSH or HTTP to get a more secure network.
Security Mode
High security level for user information verification when logging in the client software.
Compatible Mode
The user informaiton verification is compatible with the old client software version when
logging in.
125
9.7 Network Parameters Settings

Set device network parameters, including the NIC type, DHCP, and HTTP.
On the Device for Management page, click → Network → Network Parameters to enter the
Network Parameters Settings tab.
NIC Type
Select a NIC type from the drop-down list. You can select either Self-adaptive, 10M, or 100M.
DHCP
If you disable the function, you should manually set the device's IPv4 address, IPv4 subnet
mask, IPv4 default gateway, MTU, and port.
If you enable the function, the system will automatically assign IPv4 address, IPv4 subnet mask,
IPv4 default gateway for the device.
HTTP
Set the HTTP port, DNS1 server address, and DNS2 server address.
9.8 Report Strategy Settings

You can set the center group for uploading the log via the EHome protocol.
On the Device for Management page, click → Network → Report Strategy to enter the Report
Strategy Settings tab.
You can set the center group and the system will transfer logs via EHome protocol. Click Save to
save the settings.
Center Group
Select a center group from the drop-down list.
Main Channel
The device will communicate with the center via the main channel.
Note
N1 refers to wired network.
9.9 Network Center Parameters Settings

You can set the notify surveillance center, center's IP address, the port No., the protocol (EHome),
the EHome account user name,etc. to transmit data via EHome protocol.
On the Device for Management page, click Remote Configuration → Network → Network Center
Parameters to enter the Network Center Parameters Settings tab.
Select a center from the drop-down list.
126
After enabling the function, you can set the center's address type, IP address/domain name, and
port No., create EHome user name, etc.
Note
If set the EHome type as EHome5.0, you should create an EHome key as well.
Click Save.
After creating the EHome information, you can add the device via EHome protocol.
9.10 Configure Wi-Fi

Steps
1. On the Device for Management page, click → Network → Wi-Fi to enter the Wi-Fi Settings
tab.
2. Check Enable to enable the Wi-Fi function.
3. Enter the SSID name and password or you can select a network from the Wi-Fi list.
4. Set the Wi-Fi Security Mode from the drop-down list.
5. Optional: Click Refresh to refresh the network status.
6. Optional: Set WLAN parameters.
1) On the Wi-Fi Settings page, click WLAN to enter the WLAN page.
2) Uncheck DHCP and set the IP address, the subnet mask, the default gateway, the MAC
address, the DNS1 IP Address, and the DNS2 IP address.
7. Click Save.
9.11 Set Relay Parameters

Click Maintenance and Management → Device to enter the device list.
Click to enter the remote configuration page.
Click Alarm → Relay . Select a relay and click and set the relay name and output delay time.
Click OK to save the settings.
9.12 Set Access Control Parameters

Steps
1. On the Device for Management page, click → Others → Access Control Parameters to enter
the Access Control Parameters tab.
2. Check the checkbox to enable the function.
Voice Prompt
If you enable this function, the voice prompt is enabled in the device. You can hear the voice
prompt when operating in the device.
3. Click Save.
127
9.13 Configure Volume Input or Output

Steps
1. On the Device for Management page, click → Image → Audio Input or Output to enter
Audio Input or Output tab.
2. Move the block to adjust the device input and output volume.
3. Click Save.
9.14 Operate Relay

Steps
1. Click Maintenance and Management → Device to enter the device list.
2. Click to enter the remote configuration page.
3. Click Operation → Relay .
4. Enable or disable the relay.
9.15 View Relay Status

Click Maintenance and Management → Device Management → Device to enter the device list.
Click to enter the remote configuration page.
Click Status → Relay and you can view the relay status.
128
Chapter 10 Mobile Client Configuration

After adding the access control device to the mobile client, you can control door status, set door
open duration, change super password, and view access control logs.
Get Hik-Connect Mobile Client from the following ways:
• Visit https://appstore.hikvision.com to download the application according to your mobile
phone system.
• Visit the official website of our company. Then go to Support → Tool → Hikvision App Store to
download the application according to your mobile phone system.
• Scan the QR code below to download the application.
Figure 10-1 Hik-Connect QR Code
10.1 Control Door Status

The Mobile Client allows you to control the status of the access control devices' related doors by
the super password of the device.
Before You Start
• Add an access control device to the Mobile Client. See Add Device for Management in User
Manual of Hik-Connect for details.
• Link doors to the access control device. See the user manual of the access control device for
details.
Steps
Note
You can change the super password. See Change Super Password for details.
1. On the device list page, tap the door icon on the right of the access control device to enter the
door control page.
Figure 10-2 The Icon Representing Door
129
2. Control the door status.

Remain Open
Keep the door open.
Open Door
Open the door for a configurable time period. When the time period expires, the door will
close.
Note
For details about configuring the time period, see Set Door Open Duration .
Remain Closed
Keep the door closed. In this status, the door can only be opened by super card or super
password.
Note
For details about super card, see the user manual of the access control device.
3. Enter the super password.
Note
By default, the super password is the device verification code. You can change the super
password. See Change Super Password for details.
The door status will change.
10.2 Set Door Open Duration

You can set the door open duration for the access control device. When the duration expires, the
door will close automatically.
Before You Start
You should have added an access control device to the Mobile Client.
See Add Device for Management in the user manual of the Hik-Connect mobile client for details.
Steps
1. Enter the Settings page of the access control device.
- On the device list page, if the page is in the list mode, swipe the device name to the left and
tap .
- On the device list page, if the page is in thumbnail mode, tap the device name or tap .
- On the Live View page, tap and then tap Settings.
130
Note
For details about how to enter the Live View page, see Start and Stop Live View on the user
manual of Hik-Connect mobile client.
2. Tap Door Open Duration to open the Door Open Duration list.
3. Select a duration from the list.
4. Tap to confirm the selection.
If you tap Open Door in the door control page, the door will open for the configured time
duration.
Note
For details about controlling door status, see Control Door Status.
10.3 Change Super Password

The Mobile Client allows you to change the super password of the access control device, which can
be used to open all the access control points (e.g., doors), even when the access control point is in
remaining closed status.
Before You Start
Add an access control device to the Mobile Client. See Add Device for Management in the user
manual of Hik-Connect mobile client for details.
Steps
Note
For details about super password of the access control device, see the user manual of the device.
1. Enter the Settings page of the access control device.
- On the device list page, if the device list is in list mode, swipe the name of the access control
device to the left and tap .
- On the device list page, if the device list is in thumbnail mode, tap the name of the access
control device or tap .
- On the Live View page. tap and then tap Settings.
Note
For details about how to enter the Live View page, see Start and Stop Live View in the user
manual of Hik-Connect mobile client.
2. Tap Change Password to enter the Change Password page.
3. Enter the old password and tap Next.
Note
If it is the first time to set the super password, skip this step.
131
4. Create a new password and then tap Finish.
Note
The password should contain 6 numbers.
10.4 View Access Control Logs

You can view the access control device's logs including the access control events and alarm
information. You can also filter the logs.
Steps
1. On the device list page, tap the door icon on the right of the access control device to enter the
door control page.
Figure 10-3 The Icon Representing Door

The log list will be displayed on the Log section of the page.
2. Perform the following operations.
Refresh Log List Swipe the log list downward to refresh it.
View All Logs Tap View All Logs to enter the Log page and view all access control device
logs.
Filter Logs On the Log page, tap Filter and then set the filtering condition (time and
event type) to filter.
132
Appendix A. Tips for Scanning Fingerprint
Recommended Finger
Forefinger, middle finger or the third finger.
Correct Scanning
The figure displayed below is the correct way to scan your finger:
You should press your finger on the scanner horizontally. The center of your scanned finger should
align with the scanner center.
Incorrect Scanning
The figures of scanning fingerprint displayed below are incorrect:
Environment
The scanner should avoid direct sun light, high temperature, humid conditions and rain.
When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your
finger and scan again.
133
Others
If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other
authentication methods.
If you have injuries on the scanned finger, the scanner may not recognize. You can change another
finger and try again.
134
Appendix B. Access Control Capacity

View the access control data's capacity, including the card permission, door status, card reader
authentication mode, and attendance data.
Table B-1 Card Permission
Content Maximum Configurable Parameters
Week Schedule 32
Up to 8 time durations are supported for one
week schedule
Holiday Schedule 128
Up to 8 time durations are supported for one
holiday schedule.
One holiday schedule can belong to multiple
holiday groups.
Holiday Group 64
Up to 16 holiday schedules are supported for
one holiday group.
Schedule Template 64
Up to 1 week schedule and 4 holiday groups are
supported for one schedule template.
Table B-2 Door Status
Week Schedule 1
Holiday Schedule 32
Holiday Group 4
Schedule Template 1
Table B-3 Card Reader Authentication Mode
Week Schedule 2
Holiday Schedule 64
Holiday Group 8
Schedule Template 2
135
Table B-4 Attendance

Department 32
Normal Shift 32
Man-Hour Shift 32
Holiday 32
Holiday Group 64
Schedule by Department 32
Schedule by Individual 32
136
Appendix C. Attendance Record Deleting Rule
Enable Record Delete

Set the percentage of the attendance record over threshold prompt.
1. When the record reaches the threshold, an alarm of the attendance record over limit value will
be displayed on device screen. The alarm information is: Log will be full, export the report. Card
authentication is available. The interface will be back to the alarm interface after authenticating
2. When the record is full, an alarm of the attendance record over limit value will be displayed on
the device screen. The alarm information is: Log is full, export the report. Card authentication is
available. And the first 3000 attendance records will be deleted automatically. The interface will
be back to the alarm interface after authentication.
3. Deleting by time and deleting all are available when deleting the attendance records.
Disable Record Delete

Set the percentage of the attendance record over threshold prompt.
1. When the record reaches the threshold, an alarm of the attendance record over limit value will
be displayed on device screen. The alarm information is: Log will be full, export the report. Card
authentication is available. The interface will be back to the alarm interface after authenticating.
2. When the record is full, an alarm of the attendance record over limit value will be displayed on
the device screen. The alarm information is: Log is full, export the report. Card authentication is
available. And there will be no new attendance records added. The interface will be back to the
alarm interface after authenticating.
3. Deleting by time and deleting all are available when deleting the attendance records.
137
Appendix D. Attendance Report Table

Enter a short description of your concept here (optional).
This is the start of your concept.
Description of Attendance Report File Name

File Name Rule: Device No. + Report Type.xls
Device No.: A serial of numbers from 0 to 8.
Report Type:
• AbnormalAttendancel: The Attendance Abnormal table
• AbnormalAttendance2: When the row of the Abnormal Attendance table is more than 60000,
the record will be export in two tables. Here AbnormalAttendance2 refers to the second
abnormal attendance table.
• AttendanceSummary: The Attendance Summary table
• AttendanceRecord: The Attendance Record table
• AttendanceSchedule: The attendance schedule table
• NormalShift: The Normal Shift table
• ManHourShift: The Man-Hour Shift table
Attendance Schedule Table
Attendance Schedule
Create Time: 2017-04-26 10:12:20
Emplo Card Name Depart 2017/01/01 2017/01/02 2017/01/03 2017/01/04
yee ID No. ment (Sun.) (Mon.) (Tue.) (Wed.)
Shift Shift Shift Shift Shift Shift Shift Shift
No. Type No. Type No. Type No. Type
Attendance Schedule Table: All users shift schedule information for a period will be displayed in
this table. You are able to set the shift information and the holiday (No attendance recorded during
the holiday) in shift schedule configuration.
• Employee ID: The user's ID No.
• Card No.: The user's card No.
• Name: The user's name.
• Department: The department of the user.
138
Normal Shift Table
Normal Shift
Create Time: 2017-04-26 10:12:20
Shift Shift Period 1 Period 2 Period 3 Period 4
No. Name
Start Stop Start Stop Start Stop Start Stop
Normal Shift Table: Up to 4 periods can be configured in normal shift configuration. You are able to
take attendance according to the configured period.
For example: If set Period 1 to 9:00 (Start) and 17:00 (End), it is effective for the user to take
attendance between 9:00 and 17:00.
Combining with the attendance rule, you are able to set multiple attendance types.
Man-Hour Shift Table
Man-Hour Shift Table

Create Time: 2017-04-26 10:12:20
Shift No. Shift Name Work Duration Latest Start- Period 1
(min) Work Time
Start End
Man-Hour Shift Table: Set the Man-Hour Shift working duration. If set the Latest Start-Work Time
to 0, all users are attendant. If set the Latest Start-Work Time to more than 0, the user will be
absent by taking attendance after the configured time.
For example: If set the working duration to 6 hours, the start-work time to 09:00, the end-work
time to 17:00 and the break period is from 12:00 to 13:00, the user actual working hour is 17:00 -
09:00 - (13:00 - 12:00).
Abnormal Attendance Table
Abnormal Attendance Table

Create Time: 2017-04-26 10:12:20
Employee Card No. Name Departme SW-EW Late Early Total (min)
ID nt Duration Leave
(min)
139
Duration
(min)
Abnormal Attendance Record Table: Calculate the abnormal attendance according to the
attendance records and the shift schedule configuration.
• Date: The date of the data generated.
• SW-EW: Up to 4 periods can be configured. It records the attendance time of each user every
day.
• Late Duration (min): The start-work attendance time is later than the normal start-work time.
• Early Leave Duration (min): The end-work attendance time is earlier than the normal end-work
time.
• Total: The absence time duration of the day.
Attendance Record Table
Attendance Record Table

Create Time: 2017-04-26 10:12:20
Employ Card Name Depart 2017/ 2017/ 2017/ 2017/ 2017/ 2017/
ee ID No. ment 01/01 01/02 01/03 01/04 01/05 01/06
SW-EW SW-EW SW-EW SW-EW SW-EW SW-EW
Attendance Record Table: Input the start work time and the end work time to export the effective
attendance data during the configured duration.
• Card No.: The user’s card No.
Attendance Summary Table
Attendance Summary Table

Create Time: 2017-04-26 10:12:20
140
Employ Card Name Depart Late Late Early Absence Absence Attenda
ee ID No. ment Times Duratio Leave Times Time nce/
n (min) Duratio Duratio Total
n (min) n (min) Work
Days
Attendance Summary Table: Enter the start time and the end time to calculate the user attendance
information via the shift information and the holiday information according to the shift schedule
configuration.
• The user's name.
• Department: The user's department.
• Late Times: The start-work attendance time is later than the normal start-work time. Late
arriving for no more than once every day.
• Late Duration (min): Total time duration for late.
• Early Leave Times: The end-work attendance time is earlier than the normal end-work time.
Early leave for no more than once every day.
• Early Leave Duration (min): Total time duration for early leave.
• Absence Times: Total absence times.
• Absence Time Duration (min): Total absence duration.
• Attendance/Total Work Days: Total attendance days.
141
Appendix E. Custom Wiegand Rule Descriptions

Take Wiegand 44 as an example, the setting values in the Custom Wiegand tab are as follows:
Custom Wiegand Wiegand 44

Name
Total Length 44
Transformation Rule byFormatRule[4]=[1][4][0][0]
(Decimal Digit)
Parity Mode XOR Parity
Odd Parity Start Bit Length
Even Parity Start Bit Length
XOR Parity Start Bit 0 Length per Group 4 Total Length 40
Card ID Start Bit 0 Length 32 Decimal Digit 10
Site Code Start Bit Length Decimal Digit
OEM Start Bit Length Decimal Digit
Manufacturer Code 32 Length 8 Decimal Digit 3
Start Bit
Wiegand Data
Wiegand Data = Valid Data + Parity Data
Total Length
Wiegand data length.
Transportation Rule
4 bytes. Display the combination types of valid data. The example displays the combination of Card
ID and Manufacturer Code. The valid data can be single rule, or combination of multiple rules.
Parity Mode
Valid parity for Wiegand data. You can select either odd parity or even parity.
Odd Parity Start Bit, and Length
If you select Odd Parity, these items are available. If the odd parity start bit is 1, and the length is
12, then the system will start odd parity calculation from bit 1. It will calculate 12 bits. The result
will be in bit 0. (Bit 0 is the first bit.)
142
Even Parity Start Bit, and Length

If you select Even Parity, these items are available. If the even parity start bit is 12, and the length is
12, then the system will start even parity calculation from bit 12. It will calculate 12 bits. The result
will be in the last bit.
XOR Parity Start Bit, Length per Group, and Total Length
If you select XOR Parity, these items are available. Depending on the table displayed above, the
start bit is 0, the length per group is 4, and the total length is 40. It means that the system will
calculate from bit 0, calculate every 4 bit, and calculate 40 bits in total (10 groups in total). The
result will be in the last 4 bits. (The result length is the same as the length per group.)
Card ID Start Bit, Length, and Decimal Digit
If you use the transformation rule, these items are available. Depending on the table displayed
above, the card ID start bit is 0, the length is 32, and the decimal digit is 10. It represents that from
bit 0, there are 32 bits represent the card ID. (The length here is calculated by bit.) And the decimal
digit length is 10 bits.
Site Code Start Bit, Length, and Decimal Digit
If you use the transformation rule, these items are available. For detailed information, see the
explanation of the card ID.
OEM Start Bit, Length, and Decimal Digit
If you use the transformation rule, these items are available. For detailed information, see the
explanation of the card ID.
Manufacturer Code Start Bit, Length, and Decimal Digit
If you use the transformation rule, these items are available. Depending on the table displayed
above, the manufacturer code start bit is 32, length is 8, and decimal digit is 3. It represents that
from bit 32, there are 8 bits are manufacturer code. (The length here is calculated by bit.) And the
decimal length is 3.
143
Appendix F. Communication Matrix and Device

Command
Communication Matrix
Scan the following QR code to get the device communication matrix.
Note that the matrix contains all communication ports of Hikvision access control and video
intercom devices.
Figure F-1 QR Code of Communication Matrix
Device Command
Scan the following QR code to get the device common serial port commands.
Note that the command list contains all commonly used serial ports commands for all Hikvision
access control and video intercom devices.
Figure F-2 Device Command
144
UD18256B-A

Ud18256b - Baseline - Ds k1t804 Series Fingerprint Access Control Terminal - User Manual - v1.0 - 20201207

Uploaded by

Copyright:

Available Formats

Ud18256b - Baseline - Ds k1t804 Series Fingerprint Access Control Terminal - User Manual - v1.0 - 20201207

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ud18256b - Baseline - Ds k1t804 Series Fingerprint Access Control Terminal - User Manual - v1.0 - 20201207

Uploaded by

Copyright:

Available Formats

Fingerprint Access Control Terminal

About this Manual

PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED

Indicates a potentially hazardous situation which, if not avoided, could

2006/66/EC (battery directive): This product contains a battery that cannot be

Industry Canada ICES-003 Compliance

Product Name Model Description

7.6 Access Control ...................................................................................................................... 28

8.1 Add Device ........................................................................................................................... 57

8.5.1 Configure Device Parameters ...................................................................................... 78

9.2 Change Device Password ................................................................................................... 123

Chapter 3 Appearance Description

Figure 3-1 Device Appearance

Table 3-1 Appearance Description

Figure 3-2 Keypad Description

3 Numeric Keys/​Letter Keys: Press to input numbers or letters.

Chapter 4 Device Wiring

4.1 Terminal Description

Figure 4-1 Terminal Diagram

Table 4-1 Wiring with Secure Door Control Unit Description

Cable Group No. Function Color Terminal Description

4.2 External Device Wiring

Figure 4-2 External Device Wiring

4.3 Secure Door Control Unit Wiring

Figure 4-3 Secure Door Control Unit Wiring

Figure 5-1 Install Gang Box

Figure 5-2 Install Mounting Plate

Figure 5-3 Install Device

Figure 5-4 Secure

6.1 Activate via Device

6.2 Activate via SADP

Before You Start

Status of the device becomes Active after successful activation.

6.3 Activate Device via Client Software

Chapter 7 Local Settings

7.1 Select Language

7.2 Add Administrator

Figure 7-1 Add Administrator

View Info.: View the user's added card information.

according to the configured authentication mode. By default, the authentication mode is

7.3 Local Login

7.4 Communication Settings

7.4.1 Set Network

7.4.2 Set Wi-Fi Parameters

Figure 7-2 Wi-Fi Page

7.4.3 Change Verification Code

7.4.4 Set EHome Parameters

Figure 7-3 EHome Settings

7.4.5 Set Wiegand Parameters

7.4.6 Set RS-485 Parameters

Figure 7-4 Set RS-485 Parameters

7.5 Person Management

7.5.1 Add Person

Figure 7-5 New Page

View Info.: View the user's added card information.

the configured authentication mode. By default, the authentication mode is Controller.

7.5.2 Manage Person (Search/Edit/Delete)

7.6 Access Control

7.6.1 Access Control Configuration Flow

3 Numeric Keys/Letter Keys: Press to input numbers or letters.