Engine Tdi 6 Cyl Ea897 Gen2 Service Manual Eng

Service
Workshop Manual
Audi A4 2015 ➤ , Audi A5 2016 ➤ ,
Audi A6 2019 ➤ ,
Audi A7 Sportback 2018 ➤ ,
Audi A8 2018 ➤ , Audi Q5 2017 ➤ ,
Audi Q7 2016 ➤ , Audi Q8 2018 ➤
Servicing 6-cylinder TDI engine, common rail (EA 897
Gen. II)
Engine ID
DCP DEW DDV DDV DDV DDV DEW DHX DHX
C A C B E F B A C
DCP
E
Edition 01.2019
Service Department. Technical Information

Service
List of Workshop Manual Repair Groups
Repair Group
00 - Technical data
10 - Removing and installing engine
13 - Crankshaft group
15 - Cylinder head, valve gear
17 - Lubrication
19 - Cooling
21 - Turbocharging/supercharging
23 - Mixture preparation - injection
26 - Exhaust system
28 - Glow plug system
Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.
Audi A4 2015 ➤ , Audi A5 2016 ➤ , Audi A6 2019 ➤ , Audi A7 Sportback 20 ...
Servicing 6-cylinder TDI engine, common rail (EA 897 Gen. II) - Edition 01.2019
Contents
00 - Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Engine number/engine data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Safety precautions when working on the fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.2 Safety precautions when working on vehicles with start/stop system . . . . . . . . . . . . . . . . 2
2.3 Safety precautions when using testers and measuring instruments during a road test . . . . 3
2.4 Safety precautions when working on the cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.5 Safety precautions when working on the exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.6 Safety precautions when working on the SCR system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.7 Safety precautions when working on the glow plug system . . . . . . . . . . . . . . . . . . . . . . . . 5
2.8 Safety precautions when working on the subframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Repair instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Rules for cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 General repair instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Foreign particles in engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5 Contact corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 Routing and attachment of pipes, hoses and wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.7 Installing radiators and condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.8 Performing adaptions after renewing a component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
10 - Removing and installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Removing and installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Assembly mountings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Engine cover panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 Removing and installing engine cover panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
13 - Crankshaft group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1 Cylinder block (pulley end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 Exploded view - cylinder block (pulley end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.2 Exploded view - sealing flange (pulley end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.3 Removing and installing poly V-belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.4 Removing and installing tensioner for poly V-belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.5 Removing and installing vibration damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.6 Removing and installing bracket for ancillaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.7 Removing and installing engine support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.8 Renewing crankshaft oil seal (pulley end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.9 Removing and installing sealing flange (pulley end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2 Cylinder block (gearbox end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.1 Exploded view - cylinder block (gearbox end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.2 Removing and installing drive plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.3 Renewing crankshaft oil seal (gearbox end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3 Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.1 Exploded view - crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.2 Crankshaft dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.3 Allocation of main bearing shells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.4 Measuring axial clearance of crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.5 Measuring radial clearance of crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.6 Checking sender wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4 Balance shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.1 Exploded view - balance shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Contents i
4.2 Removing and installing balance shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4.3 Renewing roller bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5 Pistons and conrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.1 Exploded view - pistons and conrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.2 Removing and installing pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.3 Measuring piston projection at TDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.4 Checking pistons and cylinder bores . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.5 Checking radial clearance of conrod bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
15 - Cylinder head, valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

1 Timing chain cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1.1 Exploded view - timing chain cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1.2 Removing and installing timing chain cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2 Chain drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
2.1 Exploded view - camshaft timing chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
2.2 Exploded view - drive chain for high-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
2.3 Exploded view - drive chain for oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2.4 Exploded view - intermediate drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2.5 Removing camshaft timing chain from camshafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2.6 Removing and installing camshaft timing chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
2.7 Removing and installing drive chain for high-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . 100
2.8 Installing intermediate drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
3 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.1 Exploded view - cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.2 Exploded view - cylinder head cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
3.3 Removing and installing cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
3.4 Removing and installing cylinder head cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.5 Removing and installing seals for injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
3.6 Checking compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
4 Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
4.1 Exploded view - valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
4.2 Measuring axial clearance of camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
4.3 Measuring radial clearance of camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
4.4 Removing and installing camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
4.5 Removing and installing valve stem oil seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
5 Inlet and exhaust valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
5.1 Machining valve seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
5.2 Checking valve guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
5.3 Checking valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
5.4 Valve dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
17 - Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
1 Sump/oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
1.1 Exploded view - sump/oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
1.2 Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
1.3 Removing and installing sump (bottom section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
1.4 Removing and installing sump (top section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
1.5 Removing and installing oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
1.6 Removing and installing oil level and oil temperature sender G266 . . . . . . . . . . . . . . . . . . 169
2 Engine oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
2.1 Exploded view - engine oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
2.2 Removing and installing engine oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
2.3 Removing and installing temperature regulator for engine oil cooler . . . . . . . . . . . . . . . . . . 173
3 Crankcase breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
3.1 Exploded view - crankcase breather system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
ii Contents
3.2 Removing and installing oil separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

4 Oil filter/oil pressure switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
4.1 Exploded view - oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
4.2 Removing and installing oil filter housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
4.3 Removing and installing oil pressure sender G10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
4.4 Checking oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
4.5 Removing and installing valve for oil pressure control N428 . . . . . . . . . . . . . . . . . . . . . . . . 180
4.6 Removing and installing oil temperature sender 2 G664 . . . . . . . . . . . . . . . . . . . . . . . . . . 181
19 - Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1 Cooling system/coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1.1 Connection diagram - coolant hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1.2 Checking cooling system for leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
1.3 Draining and filling cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
2 Coolant pump/thermostat assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
2.1 Exploded view - coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
2.2 Exploded view - electric coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
2.3 Exploded view - thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
2.4 Exploded view - coolant temperature senders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
2.5 Removing and installing electric coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
2.6 Removing and installing coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
2.7 Removing and installing thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
2.8 Removing and installing thermostat housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
2.9 Removing and installing coolant temperature sender G62 . . . . . . . . . . . . . . . . . . . . . . . . 196
2.10 Removing and installing temperature sender for engine temperature regulation G694 . . 197
2.11 Removing and installing coolant valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
3 Coolant pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
4 Radiator/radiator fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
21 - Turbocharging/supercharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
1 Turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
1.1 Exploded view - turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
1.2 Removing and installing turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
2 Charge air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
2.1 Exploded view - charge air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
2.2 Exploded view - hose connections for charge air system . . . . . . . . . . . . . . . . . . . . . . . . . . 211
2.3 Removing and installing charge air cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
2.4 Removing and installing charge pressure sender G31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
2.5 Removing and installing charge air temperature sender . . . . . . . . . . . . . . . . . . . . . . . . . . 213
2.6 Checking charge air system for leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
23 - Mixture preparation - injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

1 Injection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.1 Overview - fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.2 Overview of fitting locations - injection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.3 Filling and bleeding fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
1.4 Checking fuel system for leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
2 Vacuum system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
2.1 Connection diagram - vacuum system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
2.2 Checking vacuum system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
3 Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
4 Intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
4.1 Exploded view - intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
4.2 Removing and installing intake manifold (top section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Contents iii
4.3 Removing and installing intake manifold (bottom section) . . . . . . . . . . . . . . . . . . . . . . . . . . 232

4.4 Removing and installing intake manifold flap motor V157 . . . . . . . . . . . . . . . . . . . . . . . . . . 234
4.5 Removing and installing throttle valve module J338 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
5 Injectors/high-pressure reservoir (rail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
5.1 Exploded view - injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
5.2 Checking injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
5.3 Performing adaption of correction values for injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
5.4 Checking for injectors sticking open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
5.5 Checking return flow rate of injectors with engine running . . . . . . . . . . . . . . . . . . . . . . . . . . 246
5.6 Checking return flow rate of injectors at starter cranking speed . . . . . . . . . . . . . . . . . . . . 250
5.7 Checking pressure retention valve in fuel return line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
5.8 Removing and installing injectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
5.9 Installing high-pressure pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
5.10 Removing and installing high-pressure reservoir (rail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
6 Senders and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
6.1 Removing and installing air mass meter G70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
6.2 Removing and installing fuel temperature sender G81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
6.3 Removing and installing fuel pressure sender G247 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
6.4 Removing and installing fuel pressure sender for low pressure G410 . . . . . . . . . . . . . . . . 274
6.5 Checking fuel pressure regulating valve N276 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
6.6 Removing and installing fuel pressure regulating valve N276 . . . . . . . . . . . . . . . . . . . . . . 275
6.7 Removing and installing pressure differential sender G505 . . . . . . . . . . . . . . . . . . . . . . . . 279
7 High-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
7.1 Exploded view - high-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
7.2 Removing and installing high-pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
8 Lambda probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
8.1 Exploded view - Lambda probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
8.2 Removing and installing Lambda probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
8.3 Removing and installing NOx senders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
8.4 Removing and installing particulate sensor G784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
9 Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
26 - Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

1 Exhaust pipes/silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.1 Exploded view - silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.2 Removing and installing front exhaust pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.3 Separating exhaust pipes/silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.4 Removing and installing silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.5 Stress-free alignment of exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
1.6 Checking exhaust system for leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
2 Emission control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
2.1 Exploded view - emission control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
2.2 Removing and installing emission control module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
2.3 Removing and installing trap catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
2.4 Removing and installing exhaust flap control unit J883 . . . . . . . . . . . . . . . . . . . . . . . . . . 298
3 SCR (selective catalytic reduction) system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
3.1 Exploded view - reducing agent tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
3.2 Exploded view - reducing agent supply line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
3.3 Releasing pressure in SCR system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
3.4 Draining reducing agent tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
3.5 Removing and installing reducing agent tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
3.6 Removing and installing injector for reducing agent N474 . . . . . . . . . . . . . . . . . . . . . . . . 302
3.7 Removing and installing control unit for reducing agent metering system J880 . . . . . . . . 303
4 Exhaust gas temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
iv Contents
4.1 Exploded view - exhaust gas temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

4.2 Removing and installing exhaust gas temperature sender 1 G235 . . . . . . . . . . . . . . . . . . 305
5 Exhaust gas recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
5.1 Exploded view - exhaust gas recirculation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
5.2 Removing and installing exhaust gas recirculation cooler . . . . . . . . . . . . . . . . . . . . . . . . . . 314
5.3 Removing and installing exhaust gas recirculation temperature sensor G98 . . . . . . . . . . 316
5.4 Removing and installing pressure sender for exhaust gas recirculation G691 . . . . . . . . . . 317
6 Exhaust manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
6.1 Exploded view - exhaust manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
6.2 Removing and installing exhaust manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
28 - Glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

1 Glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
1.1 Exploded view - glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
1.2 Removing and installing glow plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
1.3 Removing and installing automatic glow period control unit J179 . . . . . . . . . . . . . . . . . . . . 325
1.4 Removing and installing Hall sender G40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
1.5 Removing and installing engine speed sender G28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Contents v
vi Contents
00 – Technical data
1 Identification
(ARL006246; Edition 01.2019)
⇒ “1.1 Engine number/engine data”, page 1
1.1 Engine number/engine data

Engine number
♦ The engine number (engine code and serial number) can be
found on the front of the cylinder block -arrow-.
♦ There is also a sticker on the intake manifold showing the en‐
gine code and serial number.
♦ In addition, the engine code is listed on the vehicle data stick‐
ers.
Engine data
For allocation of engine code, refer to ⇒ Technical data for en‐
gines; Rep. gr. 00 ; Overview of engines .
1. Identification 1
2 Safety precautions
⇒ “2.1 Safety precautions when working on the fuel system”, page
2
⇒ “2.2 Safety precautions when working on vehicles with start/
stop system”, page 2
⇒ “2.3 Safety precautions when using testers and measuring in‐
struments during a road test”, page 3
⇒ “2.4 Safety precautions when working on the cooling system”,
page 3
⇒ “2.5 Safety precautions when working on the exhaust system”,
page 3
⇒ “2.6 Safety precautions when working on the SCR system”,
page 4
⇒ “2.7 Safety precautions when working on the glow plug system”,
page 5
⇒ “2.8 Safety precautions when working on the subframe”,
page 5
2.1 Safety precautions when working on the fuel system

Risk of injury - fuel system operates under high pressure
The fuel system is pressurised. There is a risk of injury as fuel
may spray out.
Before opening the fuel system:
– Put on safety goggles.
– Put on protective gloves.
– Release pressure (wrap a clean cloth around connection and
open connection carefully).
Risk of fire due to escaping fuel

If the battery is connected, the door contact switch activates the
fuel pump when the driver's door is opened. Escaping fuel may
ignite, causing a fire.
– Before opening the fuel system, disconnect power supply to
fuel pump.
2.2 Safety precautions when working on vehicles with start/stop system

Risk of injury - engine may start unexpectedly
The engine can start unexpectedly if the vehicle's start/stop sys‐
tem is activated. A message in the instrument cluster indicates
whether the start/stop system is activated.
– To deactivate the start/stop system, switch off the ignition.
2 Rep. gr.00 - Technical data

2.3 Safety precautions when using testers and measuring instruments during
a road test
Risk of injury if test equipment is not secured
If an accident occurs and the front passenger's airbag is triggered,
test equipment which is not secured adequately may be catapul‐
ted through the vehicle with potentially serious consequences.
– Secure test equipment on the rear seat with a strap.
Or:
– Have a second mechanic operate test equipment on the rear
seat.
2.4 Safety precautions when working on the cooling system

Risk of scalding as hot coolant can escape
The cooling system is under pressure when the power unit is hot.
Risk of scalding due to hot steam and hot coolant.
– Cover filler cap on expansion tank with a cloth and open care‐
fully to release pressure.
2.5 Safety precautions when working on the exhaust system

Risk of damage to flexible joint
The flexible joint can be damaged or develop leaks if it is handled
incorrectly.
– Do not bend flexible joint more than 10°.
– Install flexible joint so that it is not under tension.
Risk of injury caused by components of the exhaust system

Danger of injury to hands and other parts of the body due to hot
or sharp parts of the exhaust system.
– Allow exhaust system to cool down.
Risk of poisoning due to chemical substances

Exhaust gas temperature senders contain chemical substances.
There is a risk of poisoning and of damage to the respiratory tract.
– Never open exhaust gas temperature sender, e.g. by cutting
or sawing it open.
2. Safety precautions 3
Risk of injury due to hot condensation and particles in exhaust

system
There may be hot condensation and/or particles in the exhaust
system. Risk of eye and skin injuries, damage to the respiratory
tract and poisoning.
– Wear protective gloves and safety goggles while performing
cutting work on the exhaust system.
– When performing cutting work, use an extraction system or
ensure sufficient ventilation.
2.6 Safety precautions when working on the SCR system

Risk of injury caused by reducing agent
Reducing agent can cause eye and skin irritation, damage to the
respiratory tract and poisoning.
– Wear protective clothing.
– Ensure that there is sufficient fresh air. In enclosed spaces,
switch on the exhaust extraction system.
Risk of damage caused by reducing agent

Reducing agent which has come into contact with trim or body
components can crystallise after some time and damage the af‐
fected surfaces.
– Ensure that no reducing agent makes contact with parts of trim
or body.
– Clean any surfaces which have come into contact with reduc‐
ing agent immediately with water and a cloth.
When removing and installing components at the SCR system,

note the following:
♦ The reducing agent tank must be empty when you are working
on the SCR system. Refer to the corresponding work descrip‐
tion to find out when the reducing agent must be drained from
the tank. Drain the reducing agent tank if necessary; proce‐
dure ⇒ page 301 .
When removing and installing the reducing agent tank, note the
following:
♦ The reducing agent tank must be empty. Drain the reducing
agent tank if necessary; procedure ⇒ page 301 .

Automatic drawing back of reducing agent

• After the ignition is switched off, the reducing agent is auto‐
matically drawn back into the reducing agent tank from the
metering line leading to the injector for reducing agent - N474- .
• Before performing work in this area, you must therefore wait
until the reducing agent has been drawn back; this can take
up to 10 minutes after the ignition has been switched off.
• It is also important to wait until the reducing agent has been
drawn back (i.e. 10 minutes after the ignition is switched off)
before disconnecting the battery ⇒ Electrical system; Rep. gr.
27 ; Battery; Disconnecting and connecting battery .
2.7 Safety precautions when working on the

glow plug system
It is important to note the following points regarding ceramic glow
plugs:
Caution
♦ Due to the special properties of the material used, ceramic

glow plugs are easily damaged and require extra care
when handling and removing/installing.
♦ Transport and store only in original packaging or packed
separately in bubble wrap.
♦ Do not remove new ceramic glow plugs from packaging
until they are ready to be fitted.
♦ Ceramic glow plugs are sensitive to knocks and bending.
For this reason, ceramic glow plugs which have been
dropped (even from a height of only about 2 cm) must not
be installed, even if no damage is apparent (hair-line
cracks may not be visible).
♦ Always install a new ceramic glow plug if you are not sure
the old one is in perfect condition.
♦ Damaged glow plugs (e.g. heater pin of ceramic glow plug
is damaged) will invariably cause engine damage.
♦ If the heater pin of the glow plug is damaged, the frag‐
ments must be removed from the combustion chamber
before starting the engine for the first time, otherwise this
will invariably cause mechanical damage (piston seizure).
If necessary, the cylinder head must be removed.
♦ The software of the engine control unit is specifically adap‐
ted to either the ceramic or the metal glow plugs, so it is
important to install the correct type.
♦ Mixed installation of ceramic glow plugs and metal glow
plugs on the same engine is not permissible.
2.8 Safety precautions when working on the subframe

Risk of damage to components
Lowering the vehicle onto its wheels can damage components if
the assembly mountings, steering rack or subframe cross brace
are not properly fitted.
– Never lower vehicle onto its wheels with suspension compo‐
nents unfastened or detached.
2. Safety precautions 5
– Never support weight of vehicle on subframe or subframe

cross brace with suspension components unfastened or de‐
tached.

3 Repair instructions
⇒ “3.1 Rules for cleanliness”, page 7
⇒ “3.2 General notes”, page 7
⇒ “3.3 General repair instructions”, page 8
⇒ “3.4 Foreign particles in engine”, page 9
⇒ “3.5 Contact corrosion”, page 9
⇒ “3.6 Routing and attachment of pipes, hoses and wiring”, page
10
⇒ “3.7 Installing radiators and condensers”, page 10
⇒ “3.8 Performing adaptions after renewing a component”,
page 10
3.1 Rules for cleanliness

Even small quantities of dirt can lead to defects. For this reason,
please observe the following rules when working on the fuel sup‐
ply system, turbocharger and injection system:
♦ Clean connections and surrounding area thoroughly with en‐
gine cleaner or brake cleaner and dry cleaned area before
loosening.
♦ Immediately seal open lines and connections with plugs (thor‐
oughly cleaned), for example from engine bung set - VAS
6122- .
♦ After removal, place parts on a clean surface and cover them.
Only use lint-free cloths.
♦ Carefully cover or seal open components if repairs cannot be
carried out immediately.
♦ Only install clean components; replacement parts should only
be unpacked immediately prior to installation. Do not use parts
that have not been stored in the proper packaging (e.g. in tool
boxes etc.).
♦ Do not work with compressed air when the system is open. If
possible, do not move vehicle.
♦ Protect unplugged electrical connectors against dirt and mois‐
ture and make sure connections are dry when attaching.
♦ Also ensure that no diesel fuel comes into contact with the
coolant hoses. Should this occur, the hoses must be cleaned
immediately. Damaged hoses must be renewed.
3.2 General notes

Fuel supply/injection
♦ The engine control unit has a self-diagnosis capability. Before
carrying out repairs and fault finding, the event memory must
be interrogated. The vacuum hoses and connections must al‐
so be checked (unmetered air).
♦ A voltage of at least 11.5 V is required for proper operation of
the electrical components.
♦ Do not use sealants containing silicone. Particles of silicone
drawn into the engine will not be burnt in the engine and will
damage the Lambda probe.
♦ The vehicles are fitted with a crash fuel shut-off system. This
system is designed to reduce the risk of a vehicle fire after a
crash by deactivating the fuel pump.
3. Repair instructions 7
♦ At the same time, this system also improves the engine's start‐
ing performance. When the driver's door is opened, the fuel
pump is activated for 2 seconds in order to build up pressure
in the fuel system ⇒ page 2 .
Glow plug system
♦ The glow plug system is activated via the automatic glow pe‐
riod control unit - J179- . The control unit is self-diagnosis
compatible.
♦ Fitting location of automatic glow period control unit -J179-
⇒ Current flow diagrams, Electrical fault finding and Fitting
locations.
♦ A fault is stored in the engine control unit - J623- if a fault oc‐
curs in the glow plug system.
♦ Checking glow plug system ⇒ Vehicle diagnostic tester
♦ For faster starting, the vehicle is equipped with electronically
controlled glow plugs and a separate glow period control unit.
♦ Each glow plug is activated and diagnosed separately.
Note
♦ Wait for 60 seconds each time after performing final control

diagnosis of the glow period control unit. The ignition must re‐
main switched on.
♦ If you do not wait for 60 seconds (if ignition is switched off and
immediately switched on again), the glow plugs can be dam‐
aged (due to repeated pre-heating).
♦ The activation of the glow plugs is controlled according to
coolant temperature.
3.3 General repair instructions
Caution
The high-pressure pump has very close tolerances and must

not be allowed to run without fuel. To prevent this and to enable
the engine to start quickly after parts have been renewed, it is
important to observe the following:
♦ If components of the fuel system between the fuel tank
and the high-pressure pump are removed or renewed, the
fuel system must be filled and bled before the engine is
started for the first time ⇒ page 217 .
♦ Clean tools and workbench etc. before working on the injection

system.
♦ Before installing, check the injectors and their surroundings
visually; they must be undamaged and clean. Make sure the
injector bores in the cylinder head are clean. Wipe out if nec‐
essary using a clean cloth, taking care not to cause damage.
Do not use sharp objects of any kind.
♦ If the high-pressure fuel lines are to be re-used, you must mark
them before removal. High-pressure pipes must always be re-
installed on the same cylinder.
♦ Take care not to damage the injectors when removing the old
copper seals.

♦ Check all new O-rings for damage before installing. Lubricate

O-rings with engine oil or assembly oil before installing.
♦ Position high-pressure pipes so they are free of stress. Tighten
all unions lightly to start with before tightening to final torque.
♦ Never attempt to bend high-pressure fuel lines to shape.
♦ When working on any parts of the high-pressure fuel system,
tools may only be used for loosening and tightening pipe un‐
ions. All other components must always be removed and
installed by hand without using tools or other equipment.
♦ Press the fuel return hoses onto the injectors by hand from
above so that they engage audibly on each injector (do not
press in the release pins when doing this). Then press down
the release pin after connecting the return line. Check that the
fuel return hoses are seated securely and sealed properly by
pulling them by hand from above.
♦ Do not dismantle individual common rail components. If there
is a fault, the complete components must be renewed.
♦ When the engine is running, do not perform any repairs to the
common rail system.
♦ Do not bleed the common rail system by unfastening high-
pressure components after the engine has been started.
♦ Use correct type of fasteners for electrical wiring (as original
equipment) ⇒ Electronic parts catalogue .
♦ Fuel hoses in engine compartment must only be secured with
spring-type clips. O-type clips or screw-type clips must not be
used.
3.4 Foreign particles in engine

♦ When performing assembly work on the engine, all open pas‐
sages in the intake and exhaust systems must be sealed with
suitable plugs (e.g. from engine bung set - VAS 6122- ) to
prevent foreign particles from entering the engine.
♦ In the event of mechanical damage to one of the cylinder
banks, the intake and exhaust systems and combustion cham‐
bers of the opposite cylinder bank must always be examined
to prevent further damage occurring later.
♦ If the turbocharger has suffered mechanical damage
⇒ page 206
3.5 Contact corrosion

Contact corrosion can occur if unsuitable fasteners are used (e.g.
bolts, nuts, washers, etc.).
For this reason, only fasteners with a special surface coating are
fitted.
Additionally, all rubber and plastic parts and all adhesives are
made of non-conductive materials.
Always install new parts if you are not sure whether used parts
can be re-fitted ⇒ Electronic parts catalogue .
Please note:
♦ We recommend using only genuine replacement parts; these
have been tested and are compatible with aluminium.
♦ We recommend using Audi Genuine Accessories.
♦ Damage caused by contact corrosion is not covered by war‐
ranty.
3.6 Routing and attachment of pipes, hoses

and wiring
♦ Mark fuel lines, hydraulic lines, vacuum lines, lines for activa‐
ted charcoal filter and electrical wiring etc. before removal so
they can be re-installed in the original positions and correctly
connected. Make sketches or take photographs if necessary.
♦ To avoid damaging pipes, hoses and wiring, ensure sufficient
clearance from all moving or hot components in engine com‐
partment (limited space in engine compartment).
3.7 Installing radiators and condensers

Even when the radiator, condenser and charge air cooler are cor‐
rectly installed, slight impressions may be visible on the fins of
these components. This does not mean that the components are
damaged. If the fins are only very slightly distorted, this does not
justify renewal of the radiator, charge air cooler or condenser.
3.8 Performing adaptions after renewing a

component
After a component has been renewed, the following programs
must be performed using the ⇒ Vehicle diagnostic tester.
– Select the correct Guided Function in the Guided Fault Finding
routine. The procedure for starting the ⇒ Vehicle diagnostic
tester is always the same.
– Connect ⇒ Vehicle diagnostic tester.
– Select Diagnosis mode and then Start diagnosis .
– Choose Select own test tab and select following options
one after the other:
Procedure - version 1:
♦ Drive train
♦ Select engine code and engine
♦ 0001 - Self-diagnosis compatible systems
♦ 0001 - Engine electronics
♦ 0001 - Engine electronics, functions
After renewing engine control unit:
♦ 0001 - Replace engine control unit
The learnt values must be adapted if components of the engine
or reducing agent system have been renewed or if a reducing
agent line has been opened:
♦ 0001 - Work steps after component replacement
Learnt values must be adapted after renewing control unit for re‐
ducing agent metering system - J880- :
♦ 0001 - Replace control unit for reducing agent me-
tering system
Procedure - version 2:
♦ Systems with diagnostic capability
♦ 0001 - Engine electronics J623


After renewing engine control unit:
♦ 0001 - Replace engine control unit
The learnt values must be adapted if components of the engine
or reducing agent system have been renewed or if a reducing
agent line has been opened:
♦ 0001 - Work steps after component replacement
Learnt values must be adapted after renewing control unit for re‐
ducing agent metering system - J880- :
♦ Systems with diagnostic capability
♦ 00AC - Control unit for reducing agent metering
system -J880
♦ 00AC - Control unit for reducing agent metering

system, functions
♦ 00AC - Replace control unit for reducing agent me-

tering system
10 – Removing and installing engine

1 Removing and installing engine
All procedures are described in ⇒ 6-cylinder TDI engine, 3.0 ltr.
4-valve common rail; Rep. gr. 10 ; Removing and installing en‐
gine .
12 Rep. gr.10 - Removing and installing engine

2 Assembly mountings
All procedures and components are described in ⇒ 6-cylinder TDI
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 10 ; Assembly
mountings .
2. Assembly mountings 13
3 Engine cover panel

⇒ “3.1 Removing and installing engine cover panel”, page 14
3.1 Removing and installing engine cover

panel
Removing
– Carefully pull engine cover panel off retaining pins one after
another -arrows-. Do not jerk engine cover panel away, and
do not try to pull on one side only. (Different versions.)
Installing
– To avoid damage, do not strike the engine cover panel with
your fist or with any kind of tool.
– When fitting engine cover panel, take care not to damage oil
filler neck.
– First press engine cover panel onto rear retaining pins and
then onto front retaining pins with both hands.
14 Rep. gr.10 - Removing and installing engine

13 – Crankshaft group
1 Cylinder block (pulley end)
⇒ “1.1 Exploded view - cylinder block (pulley end)”, page 15
⇒ “1.2 Exploded view - sealing flange (pulley end)”, page 21
⇒ “1.3 Removing and installing poly V-belt”, page 22
⇒ “1.4 Removing and installing tensioner for poly V-belt”,
page 26
⇒ “1.5 Removing and installing vibration damper”, page 27
⇒ “1.6 Removing and installing bracket for ancillaries”,
page 29
⇒ “1.7 Removing and installing engine support”, page 31
⇒ “1.8 Renewing crankshaft oil seal (pulley end)”, page 31
⇒ “1.9 Removing and installing sealing flange (pulley end)”, page
33
1.1 Exploded view - cylinder block (pulley

end)
⇒ “1.1.1 Exploded view - cylinder block (pulley end), vehicles with
alternator”, page 15
⇒ “1.1.2 Exploded view - cylinder block (pulley end), vehicles with
starter-alternator”, page 18
1.1.1 Exploded view - cylinder block (pulley end), vehicles with alternator
1. Cylinder block (pulley end) 15

1 - Poly V-belt
❑ Check for wear
❑ Do not kink
❑ Routing of poly V-belt
⇒ page 18
❑ Before removing, mark
direction of rotation with
chalk or felt-tip pen
❑ Removing and installing
⇒ “1.3 Removing and in‐
stalling poly V-belt”,
page 22
❑ When installing, make
sure it is properly seated
on pulleys
2 - Vibration damper
❑ With poly V-belt pulley
stalling vibration damp‐
er”, page 27
3 - Bolt
❑ Renew after removing
❑ 150 Nm +90°
4 - Idler roller
❑ For poly V-belt
❑ On some models, radia‐
tor must be released at
top and pressed for‐
wards slightly before it is
removed ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-
valve common rail; Rep.
gr. 19 ; Radiator/radia‐
tor fans; Exploded view - radiator/radiator fans
5 - Bolt
❑ 30 Nm
6 - Cover
❑ For idler roller
7 - Cover
8 - Bolt
❑ 30 Nm
9 - Idler roller
❑ For poly V-belt
10 - Bolt
❑ Tightening torque ⇒ Electrical system; Rep. gr. 27 ; Alternator; Exploded view - alternator
11 - Alternator
❑ Removing and installing ⇒ Electrical system; Rep. gr. 27 ; Alternator; Removing and installing alternator
12 - Bracket
❑ For alternator
⇒ “1.6.1 Removing and installing bracket for alternator - vehicles with alternator”, page 29
16 Rep. gr.13 - Crankshaft group

13 - Bolt
❑ Tightening torque and sequence ⇒ page 17
14 - Bolt
❑ Tightening torque ⇒ Item 2 (page 189)
15 - Pulley
❑ For coolant pump
16 - Bolt
❑ 50 Nm +90°
17 - Tensioner
❑ For poly V-belt
⇒ “1.4.1 Removing and installing tensioner for poly V-belt - vehicles with alternator”, page 26
18 - Seal
19 - Bracket
❑ For air conditioner compressor
⇒ “1.6.2 Removing and installing bracket for air conditioner compressor - vehicles with alternator”, page
30
20 - Bolt
❑ Self-locking
❑ Tighten in 2 stages and in diagonal sequence:
♦ 5 Nm
♦ 40 Nm
21 - Dowel sleeves
22 - Air conditioner compressor
❑ Removing and installing ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner compressor; Detaching
and attaching air conditioner compressor at bracket
23 - Bolt
❑ Tightening torque ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner compressor; Exploded view
- air conditioner compressor drive unit
Bracket for alternator -1- - tightening torque and sequence

– Tighten bolts in stages as follows:
Stage Bolts Tightening torque
1. -2- 3 Nm
2. -3- 40 Nm
3. -2- 40 Nm

Routing of poly V-belt

1- Alternator
2- Idler roller
3- Idler roller
4- Coolant pump
5- Air conditioner compressor
6- Tensioner for poly V-belt
7- Vibration damper
1.1.2 Exploded view - cylinder block (pulley end), vehicles with starter-alternator
1 - Vibration damper
❑ With poly V-belt pulley
stalling vibration damp‐
er”, page 27
2 - Bolt
❑ 150 Nm +90°
3 - Poly V-belt
❑ For starter-alternator
❑ Check for wear
❑ Do not kink
❑ Routing of poly V-belt
⇒ Fig. ““Belt routing for
starter-alternator -C29-
”“ , page 20
direction of rotation with
chalk or felt-tip pen
⇒ “1.3.2 Removing and
installing poly V-belt for
alternator - vehicles with
starter-alternator”,
page 23
❑ When installing, make
sure it is properly seated
on pulleys
4 - Tensioner
❑ For poly V-belt for start‐
er-alternator
⇒ “1.4.2 Removing and
installing tensioner for poly V-belt for starter-alternator - vehicles with starter-alternator”, page 26
5 - Bolt
❑ 8 Nm +45°
6 - Bolt

7 - Nut
8 - Stud
9 - Starter-alternator - C29-
❑ Exploded view ⇒ Electrical system; Rep. gr. 27 ; Alternator; Exploded view - alternator
10 - Bracket
❑ For starter-alternator
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 13 ; Cylinder
block (pulley end); Removing and installing bracket for ancillaries
11 - Bolt
12 - Cover
13 - Bolt
14 - Pulley
❑ For coolant pump
15 - Bolt
❑ 25 Nm
16 - Tensioner
❑ For poly V-belt for air conditioner compressor
❑ Removing and installing ⇒ page 27
17 - Vacuum line
❑ For vehicles with electric compressor
18 - Bolt
❑ 9 Nm
19 - Seal
20 - Bolt
❑ Self-locking
❑ Tighten in 2 stages and in diagonal sequence:
♦ 5 Nm
♦ 40 Nm
21 - Dowel sleeves
22 - Air conditioner compressor
❑ Removing and installing ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner compressor; Detaching
and attaching air conditioner compressor at bracket
23 - Bolt
❑ Tightening torque ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner compressor; Exploded view
- air conditioner compressor drive unit
24 - Bracket
❑ For air conditioner compressor
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 13 ; Cylinder
block (pulley end); Removing and installing bracket for ancillaries

25 - Poly V-belt
❑ Check for wear
❑ Do not kink
❑ Routing of poly V-belt ⇒ Fig. ““Belt routing for air conditioner compressor”“ , page 20
❑ Before removing, mark direction of rotation with chalk or felt-tip pen
⇒ “1.3.3 Removing and installing poly V-belt for air conditioner compressor - vehicles with starter-alter‐
nator”, page 25
❑ When installing, make sure it is properly seated on pulleys
Belt routing for starter-alternator - C29-

1- Alternator
2- Idler roller
3- Vibration damper
4- Tensioner
Belt routing for air conditioner compressor

1- Vibration damper
2- Coolant pump
3- Tensioner for poly V-belt
4- Air conditioner compressor
Bracket -1- for starter-alternator - C29- - tightening torque and

tightening sequence
1. -2- 3 Nm
2. -3- 40 Nm
3. -2- 40 Nm

1.2 Exploded view - sealing flange (pulley end)
1 - Oil seal
❑ For crankshaft (pulley
end)
❑ Renewing ⇒ page 31
2 - Sealing flange (pulley end)
❑ With noise insulation
stalling sealing flange
(pulley end)”, page 33
3 - Bracket
❑ For intake manifold flap
motor - V157-
❑ Different versions avail‐
able; for allocation refer
to ⇒ Electronic parts
catalogue
4 - Bolt
❑ 9 Nm
5 - O-rings
6 - Oil temperature sender 2 -
G664-
⇒ page 181
7 - Bolt
❑ 9 Nm
8 - Gasket
9 - Bolt
❑ Tightening torque and
sequence ⇒ page 190
10 - Thermostat housing
11 - O-ring
12 - Gasket
13 - Dowel pin
❑ 2x
14 - Bolt

Sealing flange (pulley end) - tightening torque and sequence

– Tighten bolts in stages in the sequence shown:
Stage Bolts Tightening torque/angle specification
1. - Fit sealing flange with gasket on cyl‐
inder block
2. -1- For idler roller ⇒ Item 5 (page 16) ;
tighten if fitted
3. -2 … 23- Pre-tighten to 3 Nm.
4. -24 … 28- Pre-tighten to 3 Nm1)
5. -1- Tighten bolts for idler roller further to
same tightening torque
⇒ Item 5 (page 16) 2)
6. -2 … 23- Tighten to 9 Nm
7. -24 … 28- Tighten to 9 Nm1)
♦ 1)These bolts are only relevant if sealing flange is being in‐
stalled together with oil filter and coolant pump.
♦ 2) Final tightening to same tightening torque allows for set‐
tling of gasket.
1.3 Removing and installing poly V-belt

⇒ “1.3.1 Removing and installing poly V-belt for alternator and air
conditioner compressor - vehicles with alternator”, page 22
⇒ “1.3.2 Removing and installing poly V-belt for alternator - vehi‐
cles with starter-alternator”, page 23
⇒ “1.3.3 Removing and installing poly V-belt for air conditioner
compressor - vehicles with starter-alternator”, page 25
1.3.1 Removing and installing poly V-belt for

alternator and air conditioner compres‐
sor - vehicles with alternator
Special tools and workshop equipment required
♦ Socket Torx T60 - T40087-
22 Rep. gr.13 - Crankshaft group Volkswagen Technical Site: http://vwts.ru http://vwts.info

♦ Locking tool - T40098-
Removing
Preparatory work may be necessary depending on model ⇒ 6-
cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 13 ;
Cylinder block (pulley end); Removing and installing poly V-belt .
– If not removed already, remove noise insulation (front) ⇒
General body repairs, exterior; Rep. gr. 66 ; Noise insulation;
Removing and installing noise insulation .
Caution
Running a used poly V-belt in the opposite direction could

cause irreparable damage.
♦ Before removing the poly V-belt, mark the direction of ro‐
tation with chalk or a felt-tip pen for re-installation.
– Slacken poly V-belt by turning tensioner in anti-clockwise di‐

rection -arrow- using socket Torx T 60 - T40087- .
– Detach poly V-belt and lock tensioner with locking tool -
T40098- .
Installing
Installation is carried out in reverse order; note the following:
– Fit poly V-belt ⇒ page 18 .
– Check that poly V-belt is properly seated.
Additional work depending on model ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 13 ; Cylinder block (pulley end);
Removing and installing poly V-belt
– Start engine and check that poly V-belt runs properly.
Tightening torques
♦ ⇒ General body repairs, exterior; Rep. gr. 66 ; Noise insula‐
tion; Exploded view - noise insulation

alternator - vehicles with starter-alterna‐
tor

♦ Locking pin - T10060A-
Removing
Cylinder block (pulley end); Removing and installing poly V-belt .
Caution

– Slacken poly V-belt by turning tensioner in anti-clockwise di‐

rection -arrow- using socket Torx T 60 - T40087- .
– Lock tensioner with locking pin - T10060A- and take off poly
V-belt.
Installing
– Fit poly V-belt
⇒ Fig. ““Belt routing for starter-alternator -C29- ”“ , page 20 .
Tightening torques


air conditioner compressor - vehicles
with starter-alternator
♦ Special wrench Torx T55 (commercially available)
Removing
– Remove poly V-belt for alternator
⇒ “1.3.2 Removing and installing poly V-belt for alternator -
vehicles with starter-alternator”, page 23 .
Caution

– Remove cover.
– Loosen bolt -1- half a turn.
– To slacken poly V-belt, turn tensioner anti-clockwise
-arrow B- using special wrench Torx T55. Then remove poly
V-belt.
Installing
– Fit poly V-belt
⇒ Fig. ““Belt routing for air conditioner compressor”“ ,
page 20 .
– To tension poly V-belt for air conditioner compressor, turn ten‐

sioner clockwise using special wrench Torx T55 -arrow A- as
far as stop (tensioner should remain under tension).
– Tighten bolt -1-.
– Install poly V-belt for alternator
Tightening torques
♦ ⇒ “1.1.2 Exploded view - cylinder block (pulley end), vehicles
with starter-alternator”, page 18

1.4 Removing and installing tensioner for

poly V-belt
⇒ “1.4.1 Removing and installing tensioner for poly V-belt - vehi‐
cles with alternator”, page 26
⇒ “1.4.2 Removing and installing tensioner for poly V-belt for
starter-alternator - vehicles with starter-alternator”, page 26
⇒ “1.4.3 Removing and installing tensioner for poly V-belt for air
conditioner compressor - vehicles with starter-alternator”,
page 27
1.4.1 Removing and installing tensioner for

poly V-belt - vehicles with alternator
Removing
– Detach poly V-belt from tensioner
⇒ “1.3.1 Removing and installing poly V-belt for alternator and
air conditioner compressor - vehicles with alternator”,
page 22 .
– Remove bolt -2- and detach poly V-belt tensioner -1-.
Installing
– Install poly V-belt
page 22 .
Tightening torques
with alternator”, page 15

poly V-belt for starter-alternator - vehi‐
cles with starter-alternator
Removing
– Detach poly V-belt from tensioner
– Remove bolts -arrows-.
– Remove tensioner -1-.
Installing
Tightening torques


poly V-belt for air conditioner compres‐
sor - vehicles with starter-alternator
Removing
– Slacken poly V-belt
compressor - vehicles with starter-alternator”, page 25 .
– Remove bolt -1- and detach tensioner.
Installing
compressor - vehicles with starter-alternator”, page 25 .
Tightening torques
1.5 Removing and installing vibration damp‐

er
♦ Counterhold tool - T40298- (not illustrated)
♦ Adapter - T40384-
Preparing tool
– Remove bolts -arrows- and detach adapter -1- from counter‐
hold tool -T40298/1- .
– Secure adapter -T40384- to counterhold tool.
Removing
Cylinder block (pulley end); Removing and installing vibration
damper .
– Remove poly V-belt
⇒ “1.3 Removing and installing poly V-belt”, page 22 .

– Apply counterhold tool - T40298/1- to vibration damper and

secure with bolts -arrows- (tighten to 23 Nm and fit spacer
sleeves - T40298/2- in between).
– To insert the counterhold tool -T40298/1- , the radiator cowl
may need to be pushed forwards slightly.
– Remove bolt -1-.
– Detach counterhold tool - T40298/1- and remove together with
vibration damper.
Installing
Note
After removing, renew bolts tightened with specified tightening

angle.
– Position vibration damper -1- on crankshaft -2- and secure

with a new bolt (pay attention to dowel sleeve -arrow-).
– Apply counterhold tool - T40298/1- to vibration damper and

secure with bolts -arrows- (tighten to 23 Nm and fit spacer
sleeves - T40298/2- in between).
– Tighten bolt -1- for vibration damper.
– Remove counterhold tool - T40298/1- .
⇒ “1.3 Removing and installing poly V-belt”, page 22 .
Removing and installing vibration damper
Tightening torques
♦ ⇒ “1.1 Exploded view - cylinder block (pulley end)”, page 15

1.6 Removing and installing bracket for an‐

cillaries
⇒ “1.6.1 Removing and installing bracket for alternator - vehicles
⇒ “1.6.2 Removing and installing bracket for air conditioner com‐
pressor - vehicles with alternator”, page 30
⇒ “1.6.3 Removing and installing bracket for ancillaries - vehicles
1.6.1 Removing and installing bracket for al‐

ternator - vehicles with alternator
Removing
Cylinder block (pulley end); Removing and installing bracket for
ancillaries .
page 22 .
– Remove alternator ⇒ Electrical system; Rep. gr. 27 ; Alter‐
nator; Removing and installing alternator .
– Unclip cover -1-.
– Remove bolt -2- and push idler roller forwards.
– Remove bolt -arrow- for coolant pipe (front).

– Move electrical wiring clear.

– Unscrew bolts -2, 3- and remove bracket -1-.
Installing
page 22 .
Removing and installing bracket for ancillaries
Tightening torques
♦ ⇒ Fig. ““Bracket for alternator -1- - tightening torque and se‐
quence”“ , page 17
♦ ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr.
19 ; Coolant pipes; Exploded view - coolant pipes
♦ ⇒ Electrical system; Rep. gr. 27 ; Alternator; Exploded view
- alternator
1.6.2 Removing and installing bracket for air

conditioner compressor - vehicles with
alternator
Removing
Cylinder block (pulley end); Removing and installing bracket for
ancillaries .
– Drain coolant ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common
rail; Rep. gr. 19 ; Cooling system/coolant; Draining and filling
cooling system .
page 22 .
– Remove air conditioner compressor from bracket and tie up to
left side ⇒ Heating, air conditioning; Rep. gr. 87 ; Air condi‐
tioner compressor; Detaching and attaching air conditioner
compressor at bracket .
– Remove drive shaft cover (left-side) ⇒ General body repairs,
exterior; Rep. gr. 66 ; Wheel housing liners; Exploded view -
wheel housing liner (front) .
– Detach coolant pipe (left-side) -1- from bracket for air condi‐
tioner compressor, but leave it in installation position (engine
support has been removed in illustration).

– Place a cloth underneath to catch escaping coolant.

– Lift retaining clip and disconnect coolant hose -1-.
– Unscrew bolts -arrows- and detach bracket for air conditioner
compressor.
Installing
Note
Renew seal and O-ring after removal.

page 22 .
– Connect coolant hose with plug-in connector ⇒ 6-cylinder TDI
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Radiator/
radiator fans; Exploded view - radiator/radiator fans .
– Install coolant pipe (left-side) ⇒ 6-cylinder TDI engine, 3.0 ltr.
4-valve common rail; Rep. gr. 19 ; Coolant pipes; Removing
and installing coolant pipes .
Note
Do not reuse coolant.
– Fill up with coolant ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve

common rail; Rep. gr. 19 ; Cooling system/coolant; Draining
and filling cooling system .
Removing and installing bracket for ancillaries
Tightening torques
♦ ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner com‐
pressor; Exploded view - air conditioner compressor drive unit
1.6.3 Removing and installing bracket for an‐

cillaries - vehicles with starter-alternator
4-valve common rail; Rep. gr. 13 ; Cylinder block (pulley end);
Removing and installing bracket for ancillaries .
1.7 Removing and installing engine support

4-valve common rail; Rep. gr. 13 ; Cylinder block (pulley end);
Removing and installing engine support .
1.8 Renewing crankshaft oil seal (pulley

end)

♦ Oil seal extractor - T40019-
♦ Assembly tool - T40320-
Procedure
– Remove vibration damper ⇒ page 27 .
– Adjust inner part of oil seal extractor -T40019- so it is flush with
the outer part and lock in position with knurled screw.
– Lubricate threaded head of oil seal extractor, place it in posi‐
tion and screw it into oil seal as far as possible (applying firm
pressure).
– Loosen knurled screw and turn inner part against crankshaft
until the oil seal is pulled out.
– Clamp flats of oil seal extractor in vice and use pliers to remove
seal.
– Clean contact surface and sealing surface.
– Fit guide sleeve -T40320/2- on crankshaft and slide oil seal

-1- into sealing flange (pulley end).
Note
Leave guide sleeve -T40320/2- in position on crankshaft for

pressing in oil seal.

– Apply fitting sleeve -T40320/1- to crankshaft bolt -1- for vibra‐

tion damper.
– Press oil seal -2- in as far as stop.
Remaining installation steps are carried out in reverse sequence;
note the following:
– Install vibration damper ⇒ page 27 .
1.9 Removing and installing sealing flange

(pulley end)
♦ Removal lever - 80-200-
♦ Pin wrench - 3212-
♦ Hose clip pliers - VAS 6362-

♦ Angled screwdriver - VAS 6416-
Removing
Cylinder block (pulley end); Removing and installing sealing
flange (pulley end) .
– Drain engine oil and remove oil filter element ⇒ page 163 .
– Unplug electrical connectors -1, 2- and move electrical wiring
clear.
– Detach electrical connectors -2- from bracket and move elec‐

trical wiring harness clear at cylinder head cover using remov‐
al lever - 80-200- .
– Remove bolts -2- and push coolant connection -1- clear to one
side.
– If not removed already, release hose clip -3- and disconnect
coolant hose.

– Loosen bolts -arrows- for coolant pump pulley (counterhold

with pin wrench - 3212- ).
– Remove bolts and take off poly V-belt pulley.
– Unplug electrical connector -1- for valve for oil pressure control
- N428- . (Illustration shows vehicle with alternator.)
– If fitted, remove spreader rivets -arrow- using angle driver for

cross-head screws - VAS 6416- and detach noise insulation.

– Unclip cover for idler roller.

– Slacken and remove bolts in the sequence: -28 ... 2-.
– Vehicles with alternator: Remove bolt -1- for idler roller.
– Drive crankshaft oil seal out of sealing flange after removing
sealing flange.
Installing
Note
♦ Renew bolts after removing.

♦ Renew gasket, O-ring for temperature regulator and crank‐
shaft oil seal after removing.
♦ Secure all hose connections with correct type of hose clips (as
original equipment) ⇒ Electronic parts catalogue .
– Clean surfaces; they must be free of oil and grease.

– Tighten sealing flange bolts (pulley end) ⇒ page 22 .
note the following:
– Install crankshaft oil seal (pulley end) ⇒ page 31 .
– Install oil filter element and fill up with engine oil
⇒ page 163 .
Removing and installing sealing flange (pulley end)
Tightening torques
♦ ⇒ “1.2 Exploded view - sealing flange (pulley end)”, page 21
♦ ⇒ Fig. ““Sealing flange (pulley end) - tightening torque and se‐
♦ ⇒ “4.1 Exploded view - intake manifold”, page 222
♦ ⇒ “3.1 Exploded view - cylinder head”, page 108
♦ ⇒ “2.1 Exploded view - coolant pump”, page 189

2 Cylinder block (gearbox end)

⇒ “2.1 Exploded view - cylinder block (gearbox end)”, page 37
⇒ “2.2 Removing and installing drive plate”, page 37
⇒ “2.3 Renewing crankshaft oil seal (gearbox end)”, page 39
2.1 Exploded view - cylinder block (gearbox end)
Note
Secure engine to engine and gearbox support when performing assembly work ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 10 ; Removing and installing engine; Securing engine to engine and gearbox
support .
1 - Bolt
❑ Clean threads in crank‐
shaft before screwing in
new bolts ⇒ page 37
❑ 60 Nm +90°
2 - Drive plate
❑ Check holes for clutch
module/torque convert‐
er for cracks and scoring
⇒ page 37
3 - Dowel pin
4 - Crankshaft
5 - Oil seal
❑ For crankshaft (gearbox
end)
6 - Sender wheel
❑ For engine speed send‐
er - G28-
⇒ page 37
❑ Checking sender wheel
⇒ page 46
2.2 Removing and installing drive plate

2. Cylinder block (gearbox end) 37

♦ Counterhold tool - 10-201-
Removing
• Gearbox removed ⇒ Gearbox; Rep. gr. 34 ; Removing and
installing gearbox; Removing gearbox or ⇒ Gearbox; Rep. gr.
37 ; Removing and installing gearbox; Removing gearbox .
– Insert counterhold tool - 10-201- to slacken bolts for drive plate
-1-.
Caution
Take care not to damage outer surface of bearing flange on

drive plate.
♦ Use a multi-point socket bit with a length of at least 40 mm
to slacken and tighten the drive plate bolts.
– Remove bolts and take off drive plate and sender wheel
-arrow-.
Installing
Note

angle.

Threads in crankshaft must be cleaned before any further as‐

sembly work is performed.
– Clean crankshaft flange until all residual adhesive has been
removed completely.
• Ensure you do not damage oil seal when cleaning flange.
• Use a vacuum cleaner to hoover up residual adhesive; do NOT
use compressed air.
– Remove residual adhesive from one of the old bolts -2- for
drive plate using wire brush and remove oil residue using
brake cleaner.
– Screw cleaned bolt into a thread on crankshaft -1- and out
again; repeat this action until no further residual adhesive ap‐
pears.
• Do not screw bolt in too far; otherwise, the camshaft timing
chains located behind it may be damaged.
– When no further residual adhesive appears, repeat the pro‐
cedure for the other crankshaft threads.
• Finally, use a vacuum cleaner to hoover up residual adhesive;
do NOT use compressed air.
– Clean crankshaft flange with a cloth.
• Thread in crankshaft must be free of oil and grease.
– Check sender wheel ⇒ page 46 .

– Install sender wheel -arrow-.
– Pay attention to dowel pin when installing drive plate.
– Fit counterhold tool - 10-201- the other way round to tighten
bolts.
Tightening torques
♦ ⇒ “2.1 Exploded view - cylinder block (gearbox end)”,
page 37
2.3 Renewing crankshaft oil seal (gearbox

end)
♦ Fitting tool - T10122B-

♦ Extractor tool - T20143/2-
Procedure
– Remove drive plate ⇒ page 37 .
– Pry out oil seal using extractor tool -T20143/2- .
– Clean contact surface and sealing surface.

– Fit assembly aid -T10122/1- onto guide piece - T10122/6- and
slide oil seal -A- onto guide piece.
– Detach assembly aid -T10122/1- .
– Fit guide piece - T10122/6- onto crankshaft.

– Bolt guide piece to crankshaft through securing points -A- us‐
ing bolts -arrows-.
Caution
Risk of leaks if installed incorrectly.

♦ Slide oil seal onto crankshaft by hand to prevent sealing
lip on oil seal from folding over.
– Slide oil seal over guide piece - T10122/6- onto crankshaft by

hand.

– Press in oil seal evenly all round using thrust piece -

T10122/5- .
– Remove guide piece - T10122/6- .
– Check that oil seal and its sealing lip are correctly seated. If
sealing lip is partially folded over, repeat procedure with a new
oil seal.
– Install drive plate ⇒ page 37 .

3 Crankshaft
⇒ “3.1 Exploded view - crankshaft”, page 42
⇒ “3.2 Crankshaft dimensions”, page 43
⇒ “3.3 Allocation of main bearing shells”, page 44
⇒ “3.4 Measuring axial clearance of crankshaft”, page 44
⇒ “3.5 Measuring radial clearance of crankshaft”, page 45
⇒ “3.6 Checking sender wheel”, page 46
3.1 Exploded view - crankshaft
Note
Secure engine to engine and gearbox support when performing assembly work ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 10 ; Removing and installing engine; Securing engine to engine and gearbox
support .
1 - Crankshaft
❑ Measuring axial clear‐
ance ⇒ page 44
❑ Measuring radial clear‐
ance ⇒ page 45
❑ Crankshaft dimensions
⇒ page 43
2 - Dowel sleeve
❑ 4x
❑ Insert in cylinder block
3 - Retaining frame
4 - Bolt
❑ Use old bolts when
measuring radial clear‐
ance
5 - Thrust washer
❑ Only fitted on 3rd crank‐
shaft bearing
❑ Installation position: oil
grooves face outwards
❑ Note location
6 - Bearing shell
❑ For retaining frame
(without oil groove)
❑ Renew used bearing
shells
❑ Install new bearing
shells for retaining
frame with correct col‐
oured markings ⇒ page 44

7 - Dowel pin
❑ Check that pin is firmly seated in crankshaft
8 - Thrust washer
❑ Only fitted on 3rd crankshaft bearing
❑ Installation position: oil grooves face outwards
9 - Bearing shell
❑ For cylinder block (with oil groove)
❑ Renew used bearing shells
❑ Install new bearing shells for the cylinder block with the correct coloured markings ⇒ page 44
Retaining frame - tightening torque and sequence
Note

angle.
– Insert two dowel sleeves in cylinder block.

1. -1 … 16- 30 Nm
2. -1 … 16- 50 Nm
3. -1 … 16- Turn 180° further
Position of dowel sleeves

– Check that dowel sleeves -1 ... 4- are inserted in retaining
frame at positions shown in illustration.
• -Arrow-: Pulley end.
3.2 Crankshaft dimensions

Honing di‐ Main bearing journal Conrod journal ∅
mension ∅ mm
mm
Basic dimen‐ 65.000 – 0.022 60.000 – 0.022
sion – 0.042 – 0.042
3. Crankshaft 43
3.3 Allocation of main bearing shells

Allocation of crankshaft bearing shells for cylinder block
Bearing shells of the correct thickness are matched to the bear‐
ings in the cylinder block at the factory. Coloured dots on the
bearing shells are used to identify the bearing shell thickness.
• -Arrow-: Pulley end.
The allocation of the bearing shells to the cylinder block is iden‐
tified by a code letter next to the relevant bearing.
Letter on cylinder block Colour coding of bearing
R = Red
G= Yellow
B= Blue
Allocation of crankshaft bearing shells for retaining frame

Bearing shells of the correct thickness are matched to the bear‐
ings in the retaining frame at the factory. Coloured dots on the
side of the bearing shells are used to identify the bearing shell
thickness.
The allocation of the bearing shells to the bearing positions in the
retaining frame is indicated by a sequence of letters on the fly‐
wheel flange on the crankshaft. The first letter in the sequence
stands for bearing “1”, the second letter for bearing “2”, etc.
Letter on crankshaft Colour coding of bearing
R = Red
G= Yellow
B= Blue
3.4 Measuring axial clearance of crankshaft

♦ Universal dial gauge bracket - VW 387-

♦ Dial gauge - VAS 6079-
Procedure
– Secure dial gauge - VAS 6079- with universal dial gauge
bracket - VW 387- to cylinder block as shown in illustration.
– Apply dial gauge to crank web.
– Press crankshaft against dial gauge by hand and set gauge to
“0”.
– Push crankshaft away from dial gauge and read off value.
Axial clearance:
• New: 0.09 ... 0.25 mm.
3.5 Measuring radial clearance of crank‐

shaft
♦ Plastigauge
Procedure
– Remove retaining frame and clean bearing journals.
– Place a length of Plastigauge corresponding to the width of the
bearing on the bearing journal or in the bearing shell.
• The Plastigauge must be positioned in the centre of the bear‐
ing shell
– Fit retaining frame and secure with old bolts ⇒ page 43 without
rotating crankshaft.
– Remove retaining frame again.
– Compare width of Plastigauge with measurement scale.
Radial clearance:
• New: 0.018 ... 0.045 mm.
– When carrying out final assembly, renew bolts.
3. Crankshaft 45
3.6 Checking sender wheel
Caution
Risk of magnetic fields causing irreparable damage to sender

wheel.
♦ The sender wheel must be kept away from magnets (e.g.
base of torch, loudspeaker).
♦ If the drive plate/flywheel or the sender wheel itself has
been removed or renewed, check that the sender wheel
is operating correctly before installation.

♦ Sensor gauge - T10473-
Procedure
• Drive plate removed ⇒ page 37
– Check entire circumference of sender wheel using sensor
gauge - T10473- , as shown in illustration.

Inspection image of sender wheel

A - Sender wheel OK
B - Sender wheel defective
3. Crankshaft 47
4 Balance shaft
⇒ “4.1 Exploded view - balance shaft”, page 48
⇒ “4.2 Removing and installing balance shaft”, page 48
⇒ “4.3 Renewing roller bearings”, page 55
4.1 Exploded view - balance shaft
1 - Bolt
❑ 23 Nm
2 - Drive chain sprocket
❑ For balance shaft
3 - Balance shaft with balance
weight
❑ Gearbox end
⇒ page 48
❑ Balance shaft must be
renewed if bolt -item 4-
has been loosened
4 - Bolt
❑ Apply locking fluid when
installing; refer to ⇒
Electronic parts cata‐
logue
❑ 9 Nm
5 - Bearing plate
6 - Roller bearing
7 - Thrust washer
8 - Bolt
❑ Use locking pin - 3359-
as counterhold when
loosening and tighten‐
ing
❑ 20 Nm +45°
9 - Balance weight
❑ Pulley end
10 - Roller bearing
4.2 Removing and installing balance shaft


♦ Locking pin - 3359-
♦ Locking pin - T10060A- (2x)
♦ Key - T40049-
♦ Locking pin - T40237-
♦ Locking pin - T40316- (not illustrated)

Removing
4. Balance shaft 49
– Remove sealing flange (pulley end) ⇒ page 33 .

– Remove timing chain cover (bottom) ⇒ page 73 .
Caution
Risk of damage to valves and piston crowns.

♦ The crankshaft and camshafts must only be turned with
the chain drive mechanism fully installed.
Caution
Risk of damage to drive chain if thread of bolt exceeds speci‐

fied length.
♦ Use bolts with a maximum thread length -a- of 22 mm to
attach key -T40049- .
♦ If no suitable bolts are available, position suitable washer
(s) under bolt head so that remaining thread length does
not exceed 22 mm.
– Secure special wrench - T40049- onto crankshaft -arrows-.
Caution
Irreparable damage can be caused if the camshaft timing chain

slips.
♦ Turn crankshaft only in direction of engine rotation
-arrow-.
– Rotate crankshaft in normal direction of rotation to “TDC”.

• It should be possible to lock camshafts with locking pins -
T10060A- .
– Lock exhaust camshaft of cylinder bank 1 (right-side) at “TDC”

by inserting locking pin - T10060A- in hole -arrow-.

– Lock inlet camshaft of cylinder bank 2 (left-side) at “TDC” by

inserting locking pin - T10060A- in hole -arrow-.
A4/A5: Remove subframe cross brace ⇒ Running gear, axles,
steering; Rep. gr. 40 ; Subframe; Removing and installing sub‐
frame cross brace .
– Unscrew plug -arrow- from sump (top section).
Note
To do this on A4/A5 vehicles, the subframe cross brace must be

lowered; while doing so, do not press the joint pin of the guide link
out of the tapered seat ⇒ Running gear, axles, steering; Rep. gr.
40 ; Subframe; Removing and installing subframe cross brace .
– Screw locking pin - T40237- into hole and tighten to 20 Nm.
– Press tensioning rail of camshaft timing chain tensioner in di‐

rection of -arrow- and lock chain tensioner by inserting locking
pin -T40316- .
4. Balance shaft 51
– Lock balance shaft with locking pin - 3359- .

– Remove bolts -arrows- and detach drive chain sprocket -1-
from balance shaft.
Note
The camshaft timing chain must not be removed from the cam‐
shaft sprockets or the crankshaft.
– Remove bolt -arrow- at pulley end and detach balance weight

-1- and washer -2- from balance shaft.
– Remove locking pin - 3359- at gearbox end and remove bal‐

ance shaft -1- towards rear.
Installing
• Crankshaft locked in “TDC” position with locking pin -
T40237- .

• Lock exhaust camshaft of cylinder bank 1 (right-side) at “TDC”

using locking pin - T10060A- .
• Lock inlet camshaft of cylinder bank 2 (left-side) at “TDC” using
locking pin - T10060A- .
– Move balance shaft -1- into installation position on gearbox

end and lock in “TDC” position using locking pin - 3359- .
– Place washer -1- to installation position on pulley end and fit

balance weight -2- onto balance shaft.
• Machined surface -arrow- of balance weight must be posi‐
tioned over machined surface of balance shaft.
– Tighten bolt for balance weight.
4. Balance shaft 53
– Fit drive chain sprocket -1- with camshaft timing chain onto
balance shaft on gearbox end.
• The elongated holes in the drive chain sprocket must be
aligned centrally over the tapped holes in the balance shaft.
– Loosely screw in bolts -arrows-.
• It should just be possible to turn the drive chain sprocket on
the intermediate drive without axial movement.

rection of -arrow- and remove locking pin -T40316- .
– Release chain tensioner.
– Tighten bolts -arrows- at drive chain sprocket -1- for balance

shaft.
– Remove locking pin - T40237- and locking pin - 3359- .
– Remove locking pin - T10060A- (both sides).
Note
If it is difficult to remove one or both locking pins -T10060A- , the

valve timing must be checked ⇒ page 90 .
– Install timing chain cover (bottom) ⇒ page 73 .

– Install sealing flange (pulley end) ⇒ page 33 .
– A4/A5: Install subframe cross brace ⇒ Running gear, axles,
steering; Rep. gr. 40 ; Subframe; Removing and installing
subframe cross brace .
Tightening torques
♦ ⇒ “4.1 Exploded view - balance shaft”, page 48
♦ Plug for “TDC” marking ⇒ Item 19 (page 162)

4.3 Renewing roller bearings

♦ Special tool -T40392-
Pulling out
• Engine secured to engine and gearbox support ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 10 ; Re‐
moving and installing engine; Securing engine to engine and
gearbox support .
– Remove crankshaft ⇒ page 42 .
– Remove balance shaft ⇒ page 48 .
– Position special tool correctly on roller bearing:
• The chamfer -arrow- faces towards the roller bearing.
– Pull roller bearings (front -1- and rear -2-) out inwards using
spindle -T40392/1- and adapters -T40392/2- / -T40392/3- ; to
do so, turn nut -T40392/4- .
– Detach special tool and remove roller bearing.
4. Balance shaft 55
Installing
– Position adapter correctly on roller bearing:
• Chamfer -arrow- must face roller bearing; chamfer determines
installation depth.
– Pull roller bearings (front -1- and rear -2-) in as far as stop
using spindle -T40392/1- and adapters -T40392/2- / -
T40392/3- ; to do so, turn nut -T40392/4- .
• The sides of the roller bearings with identification lettering face
outwards.
– Install balance shaft ⇒ page 48 .
– Install crankshaft ⇒ page 42 .

5 Pistons and conrods

⇒ “5.1 Exploded view - pistons and conrods”, page 57
⇒ “5.2 Removing and installing pistons”, page 59
⇒ “5.3 Measuring piston projection at TDC”, page 61
⇒ “5.4 Checking pistons and cylinder bores”, page 63
⇒ “5.5 Checking radial clearance of conrod bearings”,
page 64
5.1 Exploded view - pistons and conrods

♦ All bearing and running surfaces must be oiled before assem‐
bling.
♦ Oil spray jet for piston cooling ⇒ page 58 .
1 - Bolts
❑ Lubricate threads and
contact surface
❑ 35 Nm +90°
2 - Conrod bearing cap
❑ Due to the cracking
method used to sepa‐
rate the bearing cap
from the conrod in man‐
ufacture, the caps only
fit in one position and
only on the appropriate
conrod
❑ Mark installation posi‐
tion for re-installation
❑ Mark cylinder allocation
in colour -B-
⇒ page 59
❑ Note when fitting: wide
contact shoulder -A-
must face same side on
conrod and conrod
bearing cap
3 - Bearing shells
❑ Note installation posi‐
tion
❑ Renew used bearing
shells
❑ Note version: Upper
bearing shell (closest to
piston) is constructed
from a more wear-re‐
sistant material; refer to
⇒ Electronic parts cata‐
logue
❑ Ensure that retaining lugs are securely seated.
4 - Conrod
❑ With industrially cracked conrod bearing cap
❑ Mark cylinder allocation in colour -B- ⇒ page 59
❑ Axial clearance for each conrod pair (when new): 0.20 … 0.44 mm
5. Pistons and conrods 57

❑ Measuring radial clearance ⇒ page 64

❑ Installation position ⇒ page 59
❑ Only renew as a complete set
❑ Note when fitting: wide contact shoulder -A- must face same side on conrod and conrod bearing cap
5 - Circlip
6 - Piston pin
❑ Removing and installing ⇒ “5.2 Removing and installing pistons”, page 59
7 - Piston
❑ Measuring piston projection at “TDC” ⇒ page 61
❑ Mark installation position and cylinder number ⇒ page 58
❑ Renew piston if cracking is visible on piston crown or piston skirt
❑ Checking pistons and cylinder bores ⇒ page 63
8 - Circlip
9 - Piston rings
❑ Measuring ring gap ⇒ page 64
❑ Measuring ring-to-groove clearance ⇒ page 64
❑ Install using piston ring pliers -VAS 211 003- ⇒ page 59
❑ Installation position: marking “TOP” or side with lettering faces towards piston crown
❑ Offset gaps by 120°
Oil spray jet for piston cooling

1- Bolt, 9 Nm
2- Oil spray jet with spray nozzle valve for piston cooling
Caution
Risk of damage to oil spray jets.

♦ Do not bend oil spray jets.
♦ Check that oil spray jets have adequate clearance after
re-installing pistons.
♦ Always renew bent oil spray jets.
Installation position of pistons
Caution
Risk of damage to piston crown.

♦ If you intend to re-install used pistons, mark the cylinder
number on the piston crown using paint. Do not attempt to
mark the piston crown with a centre punch or by making
a scratch, notch or similar.
• Installation position: Arrow -item 1- on piston crown points to

pulley end.

Installing piston rings

• Installation position: marking “TOP” or side with lettering faces
towards piston crown.
• Open up piston ring -2- using piston ring pliers -VAS 211 003-
just far enough to be able to slide it over piston -1-.
Marking conrods
– Before removing, mark mating positions of conrods and con‐
rod bearing caps with coloured pen -arrow-.
Note
♦ Only renew conrods as a complete set.

♦ Do not interchange conrod bearings.
Conrod installation position

The larger contact shoulder on the conrod -arrows- faces towards
the adjacent crankshaft bearing. Illustration shows front pair of
conrods.
5.2 Removing and installing pistons


♦ Pin - VW 222A-
♦ Piston ring clamp, commercially available

Removing
• Engine secured to engine and gearbox support ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 10 ; Re‐
moving and installing engine; Securing engine to engine and
gearbox support .
– Remove cylinder head ⇒ page 116 .
– Remove sump (top section) ⇒ page 165 .
– Mark installation position and matching of conrod bearing caps
to cylinder and to conrods for re-installation ⇒ page 59 .
– Unbolt conrod bearing caps.
– Pull out pistons upwards with conrods.

– Take circlip -2- out of piston pin boss.

– Use drift - VW 222A- to drive out piston pin -3-.
Note
If piston pin is difficult to remove, heat piston to approx. 60 °C.
– Detach piston -1- from conrod -4-.

Installing
Note

angle.
– Oil running surfaces of bearing shells.

– Install pistons using commercially available piston ring clamp.
Installation position:
• Pistons ⇒ page 58
• Conrods ⇒ page 59
– Install conrod bearing caps according to markings.
– Install sump (upper section) ⇒ page 165 .
– Install cylinder head ⇒ page 116 .
Tightening torques
♦ ⇒ “5.1 Exploded view - pistons and conrods”, page 57
5.3 Measuring piston projection at TDC
Note
Measure piston projection at “TDC” when installing new pistons

or a short engine.

♦ Measuring bridge -VW 382/7- from measuring tool - VW 382-

♦ Measuring plate -VW 385/17- from universal measuring tool -

VW 385-
Procedure
– Secure dial gauge - VAS 6079- with measuring bridge -
VW 382/7- and measuring plate -VW 385/17- to cylinder block
as shown in illustration.
– Measure projection at each piston at both locations marked
with -arrows- (seen in longitudinal direction of engine: at front
and rear of piston).
Note
♦ If the values measured for piston projection are not the same
for all pistons, use the highest value to determine the correct
gasket size.
♦ The cylinder head gasket size must be determined separately
for each cylinder bank.
– Depending on piston projection, install corresponding cylinder

head gasket according to following table:
Piston projection above top sur‐ Identification
face of cylinder block (no. of holes)
0.81…0.91 mm 1
0.91…0.96 mm 2
0.96…1.07 mm 3

Identification of cylinder head gasket

1- Part number
2- Holes
The gaskets for the left and right cylinder heads have different
shapes and cannot be interchanged.
5.4 Checking pistons and cylinder bores

Checking piston
– Using a micrometer (75 ... 100 mm), measure approx. 10 mm
from the lower edge, perpendicular to the piston pin axis.
• Maximum deviation from nominal dimension: 0.05 mm.
There are different piston sizes specifically matched to the differ‐
ent dimensions of the cylinder block.
Piston ∅ mm
Nominal dimension 82.924 … 82.936 1)
Repair oversize 82.964 … 82.976 1)
• 1) Dimensions not including coating (thickness 0.02 mm). The
coating will wear down partly in service.
Measuring cylinder bore

– Use a cylinder gauge - VAS 6078- to take measurements at 3
points in transverse direction -A- and in longitudinal direction
-B-.
• Maximum deviation from nominal dimension: 0.08 mm.
Cylinder bore ∅ mm
Nominal dimension 83.006 … 83.014 1)
Repair oversize 83.046 … 83.054 1)
• 1) Measure at 50 mm into cylinder bore.
Volkswagen Technical Site: http://vwts.ru http://vwts.info

Measuring piston ring gap

– Insert ring at right angle to cylinder wall from above and push
down into lower cylinder opening approx. 50 mm from bottom
of cylinder.
– To do so, use a piston without rings.
Piston ring new Wear limit
mm mm
1st compression ring 0.26 … 0.36 0.60
2nd compression ring 0.70 … 0.90 1.20
Oil scraper ring 0.20 … 0.40 0.70
Measuring ring-to-groove clearance

– Clean groove in piston before checking clearance.
Piston ring new Wear limit
mm mm
1st compression ring 0.09 … 0.13 0.160
2nd compression ring 0.05 … 0.09 0.11
Oil scraper ring 0.03 … 0.07 0.10
5.5 Checking radial clearance of conrod

bearings
♦ Plastigauge
Procedure
– Remove conrod bearing cap. Clean bearing cap and bearing
journal.
bearing on the bearing journal or in the bearing shell.
– Fit conrod bearing cap and secure with old bolts
⇒ Item 1 (page 57) without rotating crankshaft.
– Remove conrod bearing cap again.
Radial clearance:
• New: 0.020 ... 0.069 mm.
– Renew conrod bolts.

15 – Cylinder head, valve gear

1 Timing chain cover
⇒ “1.1 Exploded view - timing chain cover”, page 65
⇒ “1.2 Removing and installing timing chain cover”, page 68
1.1 Exploded view - timing chain cover
1 - Bolt
2 - Sender wheel
er - G28-
3 - Oil seal
❑ For crankshaft (gearbox
end)
⇒ page 39
4 - Timing chain cover (bottom)
⇒ page 73
5 - Dowel sleeve
❑ 2x
6 - Gasket
7 - Bolt
8 - Timing chain cover (left-
side)
⇒ page 68
9 - Bolt
10 - Reed valve
❑ For crankcase breather
11 - Bolt
❑ 3 Nm
12 - Reed valve
13 - Bolt
❑ 3 Nm
1. Timing chain cover 65

14 - Cover
15 - Bolt
❑ Tightening torques:
♦ 23 Nm
♦ 20 Nm when using insert tool XZN 10 -V.A.G 1331/15-
16 - O-ring
17 - Bolt
❑ 9 Nm
18 - Line
19 - O-ring
20 - Line
21 - O-ring
22 - Line
23 - Bolt
❑ 9 Nm
24 - O-ring
25 - Gasket
26 - Clamping sleeve
❑ 3x
❑ Prevents ingress of lubricant into threaded hole
27 - Bolt
28 - Timing chain cover (right-side)
29 - Bolt
❑ 3 Nm
30 - Reed valve
31 - Bolt
32 - Gasket
33 - Bolt
❑ 3 Nm
66 Rep. gr.15 - Cylinder head, valve gear

34 - Reed valve
35 - Dowel sleeve
❑ 2x
36 - Sealing element
❑ 2x
37 - Cover
❑ Not fitted on all versions
38 - Bolt
39 - Engine speed sender - G28-
Timing chain cover (top left) - tightening torque and tightening

sequence
Note

angle.

1. -1 … 9- Screw in by hand until contact is made
2. -1 … 9- 8 Nm
3. -1 … 9- 8 Nm (this step is performed to allow
for settling of timing chain cover)
4. -1 … 9- Turn 90° further
Timing chain cover (top right) - tightening torque and tightening

sequence
Note

angle.

2. -1 … 9- 8 Nm
3. -1 … 9- 8 Nm (this step is performed to allow
for settling of timing chain cover)

Timing chain cover (bottom) - tightening torque and tightening

sequence
Note

angle.

1. -1 … 18- 2 Nm
2. -1 … 18- 8 Nm
3. -1 … 18- Turn 90° further
1.2 Removing and installing timing chain

cover
⇒ “1.2.1 Removing and installing timing chain cover (top left)”,
page 68
⇒ “1.2.2 Removing and installing timing chain cover (top right)”,
page 71
⇒ “1.2.3 Removing and installing timing chain cover (bottom)”,
page 73
1.2.1 Removing and installing timing chain

cover (top left)
♦ Electric drill with plastic brush
♦ Safety goggles
♦ Sealant ⇒ Electronic parts catalogue
Removing
Timing chain cover; Removing and installing timing chain cover .
– Remove exhaust manifold (left-side) ⇒ 6-cylinder TDI engine,
3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust manifolds;
Removing and installing exhaust manifolds .
– Remove cylinder head cover, bank 2 (left-side)
⇒ “3.4.2 Removing cylinder head cover - bank 2 (left-side)”,
page 122 .

– Unscrew bolts -arrows- and remove engine lifting eye (rear

left) -1-.
– Loosen bolts in the sequence -9 ... 1-.

– Carefully release timing chain cover (top left) from bonded joint
and remove cover.
Caution
Risk of irreparable damage to engine.

♦ Block off the opening in the valve timing housing with a
clean cloth to prevent small items from dropping into the
engine when the timing chain cover (top) is removed.
Installing
Note
Renew gasket after removing.
– Remove old sealant from sealing surfaces on timing chain

cover.
Caution
Protect lubrication system against contamination.

♦ Cover exposed parts of the engine.
WARNING
Risk of eye injury.

♦ Put on safety goggles.
– Remove remaining sealant on timing chain cover -1- and cyl‐

inder head using rotating plastic brush or similar.

Note
Note expiry date of sealant.
– Cut off nozzle of tube at front marking (nozzle ∅ approx. 1.5

mm).
– Fit gasket -1-.

– Apply sealant at joints between cylinder head and timing chain
cover (bottom) -arrow-, as shown in illustration.
Caution
Make sure lubrication system is not clogged by excess sealant.

♦ The sealant bead must not be thicker than specified.
• The bead of sealant must project 1.5 … 2.0 mm above the

sealing surface.
– Apply sealant beads -1 and 2- onto clean sealing surface of

timing chain cover (left-side), as illustrated.
Note
Install timing chain cover within 5 minutes of applying sealant.
– Carefully fit timing chain cover onto cylinder head but do not
press sealant bead on yet.
• Sealant must not be allowed to get into threaded holes.
– First, screw all bolts for timing chain cover in by hand and then
tighten.
note the following:
– Install cylinder head cover (left-side)
⇒ “3.4.3 Installing cylinder head cover”, page 124 .
– Install exhaust manifold (left-side) ⇒ 6-cylinder TDI engine,
3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust manifolds;
Removing and installing exhaust manifolds .
ltr. 4-valve common rail; Rep. gr. 15 ; Timing chain cover; Re‐
moving and installing timing chain cover
Tightening torques
♦ ⇒ Fig. ““Timing chain cover (top left) - tightening torque and
tightening sequence”“ , page 67


cover (top right)
♦ Insert tool, XZN 10 - V.A.G 1331/15-

♦ Safety goggles
Removing
– Remove turbocharger ⇒ page 206 .
– Remove cylinder head cover (right-side) ⇒ page 121 .
– Remove bolt -3- and press air pipe -2- slightly towards rear
(different versions depending on model).
– Unscrew bolts -arrows- and detach bracket -1- for turbocharg‐

er.
Note
Use insert tool, XZN 10 - V.A.G 1331/15- for bolts that are difficult
to access.


– Carefully release timing chain cover (top right) from bonded
joint and detach.
Caution
Risk of irreparable damage to engine.

♦ Block off the opening in the valve timing housing with a
clean cloth to prevent small items from dropping into the
engine when the timing chain cover (top) is removed.
Installing
Note
– Remove old sealant from sealing surfaces on timing chain

cover.
Caution

WARNING
Risk of eye injury.


inder head using rotating plastic brush or similar.
Note

mm).

– Fit gasket -1-.

– Apply sealant at joints between cylinder head and timing chain
cover (bottom) -arrow-, as shown in illustration.
Caution

• The bead of sealant must project 1.5 … 2.0 mm above the

sealing surface.
– Apply sealant beads -1 and 2- onto clean sealing surface of

timing chain cover (right-side), as illustrated.
Note
– Carefully fit timing chain cover onto cylinder head but do not
tighten.
note the following:
– Install coolant pipe (bottom front) for turbocharger ⇒ 6-cylin‐
der TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ;
Coolant pipes; Removing and installing coolant pipes .
– Install cylinder head cover (right-side) ⇒ page 121 .
– Install turbocharger ⇒ page 206 .
Tightening torques
♦ ⇒ Fig. ““Timing chain cover (top right) - tightening torque and
♦ ⇒ “1.1 Exploded view - turbocharger”, page 202
♦ ⇒ “2.1 Exploded view - charge air system”, page 211

cover (bottom)
♦ Socket - T10574-
♦ Safety goggles

Removing
– Remove drive plate ⇒ page 37 .
– Remove timing chain covers (top) ⇒ page 68 , ⇒ page 71 .
– Loosen bolts -arrows- 2 turns using socket - T10574- .
Note
The bolts -arrows- must not be loosened any further than 2 turns.
– Unscrew bolts -arrows- and remove cover -1-.
Note
Use insert tool, XZN 10 - V.A.G 1331/15- for bolts that are difficult
to access.
– Unplug electrical connector -2- for engine speed sender -

G28- . (Shown with gearbox installed.)


– Carefully release timing chain cover (bottom) from bonded
joint and remove cover.
– Press crankshaft oil seal (gearbox end) out of timing chain
cover (bottom).
Installing
Note
Renew sealing elements after removing.
– Check whether dowel sleeves and clamping sleeves are fitted

in cylinder block; install if necessary:
1, 5 - Dowel sleeves
2, 3, 4 - Spring pins
– Remove old sealant from grooves on timing chain cover and
from sealing surfaces.
Caution

WARNING
Risk of eye injury.


inder block using rotating plastic brush or similar.

Note

mm).
– Fit sealing elements -arrows-.
Caution

– Apply beads of sealant onto clean sealing surface of timing

chain cover (bottom) as illustrated.
• The beads of sealant -1, 3, 5- must be 1.5 ... 2.0 mm thick.
• The beads of sealant around drillings -2- and -4- must be
1.5 … 2.0 mm thick.
Note
– Carefully fit timing chain cover onto cylinder block but do not
press sealant beads on yet.
tighten.
note the following:
– Install crankshaft oil seal (gearbox end) ⇒ page 39 .
– Install timing chain covers (top)
page 68 and
⇒ “1.2.2 Removing and installing timing chain cover (top
right)”, page 71 .
– Install drive plate ⇒ page 37 .
Tightening torques
♦ ⇒ Fig. ““Timing chain cover (bottom) - tightening torque and
♦ ⇒ “1.1 Exploded view - timing chain cover”, page 65
♦ ⇒ “5.1.1 Exploded view - exhaust gas recirculation system,
engine side (front)”, page 312

2 Chain drive
⇒ “2.1 Exploded view - camshaft timing chains”, page 77
⇒ “2.2 Exploded view - drive chain for high-pressure pump”, page
79
⇒ “2.3 Exploded view - drive chain for oil pump”, page 80
⇒ “2.4 Exploded view - intermediate drive”, page 81
⇒ “2.5 Removing camshaft timing chain from camshafts”,
page 81
⇒ “2.6 Removing and installing camshaft timing chain”,
page 91
⇒ “2.7 Removing and installing drive chain for high-pressure
pump”, page 100
⇒ “2.8 Installing intermediate drive”, page 101
2.1 Exploded view - camshaft timing chains
1 - Bolt
❑ 23 Nm
2 - Chain slip preventer
3 - Crankshaft
❑ With sprocket for cam‐
shaft timing chain
4 - Guide rail
tion
5 - Guide pin
❑ For guide rail
❑ 5 Nm +45°
6 - Camshaft timing chain
❑ Removing from cam‐
shafts ⇒ page 81
running direction with
paint
⇒ page 91
7 - Bolt
❑ 23 Nm
8 - Camshaft chain sprocket
❑ Cylinder bank 2 (left-
side)
❑ Installation position:
Side with lettering legi‐
ble from gearbox end
9 - Guide rail
tion
2. Chain drive 77
10 - Guide pin
❑ For guide rail
❑ 5 Nm +45°
11 - Bolt
❑ For balance shaft
13 - Guide rail
❑ Note installation position
14 - Guide pin
❑ For guide rail
❑ 5 Nm +45°
❑ Cylinder bank 1 (right-side)
❑ Installation position: Side with lettering legible from gearbox end
16 - Bolt
❑ 23 Nm
17 - Guide pin
❑ For tensioning rail
❑ 5 Nm +45°
18 - Tensioning rail
19 - Chain tensioner
❑ For camshaft timing chain
❑ Depending on version: O-ring may be fitted at chain tensioner
20 - Bolt
❑ 5 Nm +90°

2.2 Exploded view - drive chain for high-pressure pump
1 - Drive chain for high-pres‐

sure pump
⇒ page 100
2 - Bolt
❑ 5 Nm +90°
3 - Chain tensioner
❑ With guide rail
❑ For high-pressure pump
5 - Guide pin
❑ For guide rail
❑ 5 Nm +45°
6 - Oil spray jet
❑ For chain lubrication
7 - Bolt
❑ 5 Nm +45°
8 - Tensioning rail
9 - Crankshaft
❑ With drive chain sprock‐
et for high-pressure
pump
2. Chain drive 79
2.3 Exploded view - drive chain for oil pump
1 - Guide rail
2 - Bolt
❑ 5 Nm +90°
3 - Bolt
❑ 5 Nm +90°
4 - Drive chain
❑ For oil pump
5 - Guide pin
❑ 5 Nm +90°
6 - Guide pin
❑ 5 Nm +90°
7 - Crankshaft
❑ With drive chain sprock‐
et for oil pump
8 - Tensioning rail
9 - Oil pump
⇒ page 167
10 - Chain sprocket
❑ For oil pump
11 - Bolt
❑ Tightening torque
⇒ Item 10 (page 160)

2.4 Exploded view - intermediate drive
1 - Bolt
3 - Bolt
❑ 15 Nm +90°
4 - Intermediate drive
❑ Installing ⇒ page 101
2.5 Removing camshaft timing chain from

camshafts
2. Chain drive 81
♦ Torque wrench - VAS 6583-
♦ Counterhold tool - T10172 A- with adapters -T10172/7-
♦ Wrench, 21 mm - T40263-

♦ Assembly tool - T40309-
♦ Adapter - T40310- (not illustrated)

Removing
• Engine and gearbox in vehicle
Chain drive; Removing camshaft timing chain from camshafts .
Caution

– Remove timing chain cover (top right) ⇒ page 71 .
Caution

slips.
-arrow-.
– Use wrench, 21 mm - T40263- and adapter - T40314- to turn

crankshaft until vibration damper is at “TDC” position.
2. Chain drive 83
• Mark (stuck on) -1- must be vertical and aligned with arrow
marking on coolant pump.

T10060A- . If not, turn crankshaft 360° further in direction of
engine rotation.

frame cross brace .
Note


– Screw locking pin - T40237- into hole (20 Nm); if necessary,

turn crankshaft -1- backwards and forwards slightly to fully
centralise locking pin.
– Remove bolts -arrows- for camshaft chain sprocket for cylin‐

der bank 1 (right-side).
– Slacken bolts -arrows- by a half turn.
– With the help of a second mechanic, apply torque evenly to

camshaft chain sprocket for cylinder bank 1 (right-side) by
turning adapter - T40310- anti-clockwise -arrow- and maintain
this torque.
• This will press the chain tensioner back.
Note
The chain tensioner is oil-damped and can therefore only be

pressed back slowly by applying constant pressure.
2. Chain drive 85
– Fit retainer -T40309/1- into tensioning rail -1- and tighten bolts
-2, 3-, as shown in illustration.
1. -2- Screw in by hand until contact is made
2. -3- Screw in by hand until contact is made
3. -2- 8 Nm
4. -3- 8 Nm
– Release tension on camshaft chain sprocket for cylinder
bank 1 (right-side) and remove adapter - T40310- .
– Unscrew bolts -arrows- completely and detach camshaft chain

sprocket for cylinder bank 1 (right-side).
Note
Do not loosen bolt -arrow- for intermediate drive -1- for cylinder
bank 1 (right-side). If bolt for intermediate drive has been loos‐
ened, backlash must be re-adjusted ⇒ page 101 .
– Remove timing chain cover (top left) ⇒ page 68 .
• Inlet camshaft of cylinder bank 2 (left-side) locked at “TDC” by


– Apply counterhold tool - T10172 A- with adapter -T10172/7- to

head of bolts for camshaft chain sprocket for cylinder bank 2
(left-side) and remove bolts (re-apply counterhold tool several
times as necessary).
– Detach camshaft chain sprocket for cylinder bank 2 (left-side)
and secure camshaft timing chain with a piece of wire to pre‐
vent it from falling into chain case.
Note
Do not loosen bolt -arrow- for intermediate drive -1- for cylinder
bank 2 (left-side). If bolt for intermediate drive has been loosened,
backlash must be re-adjusted ⇒ page 105 .
Installing
T40237- .
2. Chain drive 87

Note
Locking pins -T10060A- must not be tensioned; it should be pos‐

sible to move them easily. If necessary, turn intermediate drive
slightly to align camshafts (fit two bolts and turn using counterhold
tool - T10172 A- and adapter -T10172/7- ).
– Position camshaft chain sprocket for cylinder bank 2 (left-side)

with timing chain on intermediate drive.
• The side of the chain sprocket with lettering faces the gearbox.
• The elongated holes in the camshaft chain sprocket must be
aligned centrally over the threaded holes in the intermediate
drive.
• It should just be possible to turn the camshaft chain sprocket
on the intermediate drive without axial movement.
– Position camshaft chain sprocket for cylinder bank 1 (right-

side) with timing chain on intermediate drive.
drive.
– Screw in bolts -arrows- loosely for camshaft chain sprocket for
cylinder bank 1 (right-side).
– Check that camshaft timing chain is positioned correctly on

guide rail and tensioning rail.
– With the help of a second mechanic, apply torque evenly to
camshaft chain sprocket for cylinder bank 1 (right-side) by
turning adapter - T40310- anti-clockwise -arrow- and maintain
this torque.

– Remove retainer -T40309/1- .

– Release camshaft chain sprocket.
– Remove bolts -2, 3-.
– Apply an initial torque of 10 Nm to camshaft chain sprocket for

cylinder bank 1 (right-side) in clockwise direction -arrow- using
adapter - T40310- and torque wrench - VAS 6583- .
– Detach torque wrench and adapter - T40310- from camshaft
chain sprocket.
– Pre-tighten bolts -1, 2- for camshaft chain sprocket for cylinder

bank 1 (right-side) to 10 Nm.
– Screw in bolts -arrows- for camshaft chain sprocket for cylin‐

der bank 1 (right-side) and pre-tighten to 10 Nm.
2. Chain drive 89
– Pre-tighten bolts -arrows- for camshaft chain sprocket for cyl‐

inder bank 2 (left-side) to 10 Nm.
– Tighten bolts for camshaft chain sprocket for cylinder bank 1
(right-side) to final torque.
(left-side) to final torque.
– Remove locking pin - T40237- and locking pin -T10060A- .
Checking valve timing
Caution

slips.
-arrow-.
– Turn crankshaft two rotations until vibration damper is at

“TDC” position again.
– While turning in this direction, lock crankshaft -1- with locking

pin - T40237- . Tighten locking pin to 20 Nm.
Caution
The crankshaft must be exactly in “TDC” position to ensure

accurate valve timing adjustment.
♦ If crankshaft has been turned past “TDC” position, turn
crankshaft two further rotations until it is again positioned
just before “TDC”. Then turn further in the same direction
and lock crankshaft with locking pin - T40237- .
– Check that camshafts on both cylinder heads are positioned

at “TDC”.
T10060A- .



Note
♦ The adjustment is OK even if the locking pins -T10060A- are

difficult to insert.
♦ If it is not possible to insert the locking pins -T10060A- , repeat
the adjustment procedure ⇒ page 87 .

note the following:
– Remove locking pin - T40237- and locking pin -T10060A- .
– Install timing chain covers (top)
page 68 and
⇒ “1.2.2 Removing and installing timing chain cover (top
right)”, page 71 .
ltr. 4-valve common rail; Rep. gr. 15 ; Chain drive; Removing
camshaft timing chain from camshafts .
Tightening torques
♦ ⇒ “2.1 Exploded view - camshaft timing chains”, page 77
2.6 Removing and installing camshaft tim‐

ing chain
♦ Locking pin - 3359-
2. Chain drive 91
♦ Torque wrench - VAS 6583-
♦ Counterhold tool - T10172A-
♦ Key - T40049-


Removing
Caution

Caution
Risk of damage to drive chain if thread of bolt exceeds speci‐

fied length.
♦ Use bolts with a maximum thread length -a- of 22 mm to
attach key -T40049- .
♦ If no suitable bolts are available, position suitable washer
(s) under bolt head so that remaining thread length does
not exceed 22 mm.
– Secure key - T40049- onto rear of crankshaft -arrows-.
Caution

slips.
-arrow-.
– Rotate crankshaft to “TDC”.

T10060A- .
2. Chain drive 93


frame cross brace .
Note

– Screw locking pin - T40237- into hole (20 Nm); if necessary,

turn crankshaft -1- backwards and forwards slightly to fully
centralise locking pin.


rection of -arrow- and lock chain tensioner by inserting locking
pin -T40316- .
– Remove bolt -arrow- for chain slip preventer.
Caution
If a used timing chain rotates in the opposite direction when it

is refitted, this can cause breakage.
♦ Mark running direction of timing chain with coloured ar‐
rows for re-installation.
– Apply counterhold tool - T10172A- with adapter -T10172/7- to

head of bolts for camshaft chain sprocket for cylinder bank 2
(left-side).
– Remove bolts -arrows- (apply counterhold tool for each one).

– Perform the same work step on the other side of the vehicle.
– Detach camshaft timing chain with camshaft chain sprockets.
2. Chain drive 95
Note
Do not loosen bolt -arrow- for intermediate drive -1-. If bolt for
intermediate drive has been loosened, backlash must be re-ad‐
justed ⇒ page 101 .
Installing
T40237- .


• Balance shaft locked in “TDC” position with locking pin -
3359- .
Note
♦ Locking pins -T10060A- must not be tensioned; it should be

possible to move them easily. If necessary, turn intermediate
drive slightly to align camshafts (fit two bolts and turn using
counterhold tool - T10172A- and adapter -T10172/7- ).
♦ After removing, renew bolts tightened with specified tightening
angle.
– Position camshaft chain sprocket for cylinder bank 2 (left-side)

with timing chain on intermediate drive.
drive.
– Position camshaft chain sprocket for cylinder bank 1 (right-

side) with timing chain on intermediate drive.
drive.
– Screw in bolts -arrows- loosely for camshaft chain sprocket for
cylinder bank 1 (right-side).
– Check that camshaft timing chain is positioned correctly on
guide rail and tensioning rail.

rection of -arrow- and remove locking pin -T40316- .
– Release chain tensioner.
2. Chain drive 97
– Loosen bolts -arrows- at drive chain sprocket -1- for balance

shaft.
– Lock balance shaft with locking pin - 3359- , as shown in illus‐
tration.
Note
If necessary, remove bolts and bring drive chain sprocket for bal‐
ance shaft into position.

• The elongated holes in the drive chain sprocket must be
aligned centrally over the tapped holes in the balance shaft.
• It should just be possible to turn the drive chain sprocket on
the balance shaft without axial movement.
– Apply an initial torque of 10 Nm to camshaft chain sprocket for

cylinder bank 1 (right-side) in clockwise direction -arrow- using
adapter - T40310- and torque wrench - VAS 6583- .
– Detach torque wrench and adapter - T40310- from camshaft
chain sprocket.
– Pre-tighten bolts -1, 2- for camshaft chain sprocket for cylinder

bank 1 (right-side) to 10 Nm.
– Screw in bolts -arrows- for camshaft chain sprocket for cylin‐

der bank 1 (right-side) and pre-tighten to 10 Nm.

– Pre-tighten bolts -arrows- for camshaft chain sprocket for cyl‐

inder bank 2 (left-side) to 10 Nm.
(right-side) to final torque.
(left-side) to final torque.
– Tighten bolts -arrows- at drive chain sprocket -1- for balance

shaft.
– Remove locking pin - 3359- , adapter - T40310- and locking
pin -T10060A- .
– Remove locking pin - T40237- .
Checking valve timing
Caution

slips.
-arrow-.
– Turn crankshaft two rotations until it is again positioned just

before “TDC”.

Caution


at “TDC”.
T10060A- .
2. Chain drive 99


Note
♦ The adjustment is OK even if the locking pins -T10060A- are

difficult to insert.
♦ If it is not possible to insert the locking pins -T10060A- , repeat
the adjustment procedure ⇒ page 96 .

note the following:
– Remove locking pin - T40237- and locking pin - T10060A- .
– Install timing chain covers ⇒ page 68 .
Tightening torques
♦ ⇒ “2.1 Exploded view - camshaft timing chains”, page 77
♦ ⇒ “4.1 Exploded view - balance shaft”, page 48
2.7 Removing and installing drive chain for

high-pressure pump

Removing
– Remove camshaft timing chain ⇒ page 91 .
Note
Mark position of guide rail -1- for re-installation.
– Detach guide rails -1, 2, 3- and tensioning rail -4-.
– Press tensioning rail of chain tensioner in direction of -arrow-

and lock chain tensioner by inserting locking pin -T40316- .
– Unscrew bolt -1- and remove tensioning rail.
– Detach chain sprocket for high-pressure pump slightly and re‐
move drive chain for high-pressure pump.
Installing
– Lock chain sprocket for high-pressure pump in position using
locking pin - T40245- and fit drive chain for high-pressure
pump.
– Install camshaft timing chain ⇒ page 91 .
– Remove locking pin - T40245- for chain sprocket for high-
pressure pump.
Tightening torques
♦ ⇒ “2.2 Exploded view - drive chain for high-pressure pump”,
page 79
2.8 Installing intermediate drive

⇒ “2.8.1 Installing intermediate drive for cylinder bank 1 (right-
side) and adjusting backlash”, page 101
⇒ “2.8.2 Installing intermediate drive for cylinder bank 2 (left-side)
and adjusting backlash”, page 105
2.8.1 Installing intermediate drive for cylinder

bank 1 (right-side) and adjusting back‐
lash
2. Chain drive 101

♦ TDC adjustment bar - 2068A-
♦ Setting tool - T40271-
♦ Adjustment pin - T40313-
Preparing tool
– Remove retaining ring -2- and take knurled screw -1- out of
TDC adjustment bar - 2068A- .

– Remove circlip -2- and take knurled screw -1- out.
– Slide knurled screw -1- from tool -T40271/1- into TDC adjust‐
ment bar - 2068A- , as shown in illustration.
Procedure
• Timing chain removed from camshafts.
• Camshafts for cylinder bank 1 (right-side) installed.
• Exhaust camshaft of cylinder bank 1 (right-side) locked at
“TDC” by inserting locking pin - T10060A- in hole -arrow-.
• Backlash compensation assembly of exhaust camshaft for

cylinder bank 1 (right-side) locked in place with adjustment pin
- T40313- . Teeth of the two gears of exhaust camshaft must
align ⇒ page 139 .
2. Chain drive 103

– Align flange -3- with eccentric washer -4- of intermediate drive.

• Marking -1- should align with notch -2-.
– Fit intermediate drive on cylinder head.
• Marking -1- and notch -2- must align with cast projection
-arrow- on cylinder head.
– Screw in bolt -5- for intermediate drive by hand until it makes
contact.
• It should just be possible to turn the eccentric washer of the
intermediate drive without axial movement.
– Turn eccentric washer -3- by hand anti-clockwise -arrow- as

far as stop.
– Secure TDC adjustment bar - 2068 A- to cylinder head using
knurled screw -1-, as shown in illustration.
– Align caliper gauge of TDC adjustment bar - 2068A- with
marking -4- on eccentric washer, as shown in illustration, then
secure with locking bolt -2-.
– Turn eccentric washer -1- clockwise -arrow- until line marking

-3- is aligned with TDC adjustment bar - 2068 A- , as illustrated.
– Tighten bolt -2-, ensuring that eccentric washer remains in
setting position.
Note
On some versions, there is no line marking on the eccentric wash‐

er. If this is the case, a mark -2- must be made at a distance -a-
= 5.2 mm to the right of the notch -1-.

2.8.2 Installing intermediate drive for cylinder

bank 2 (left-side) and adjusting backlash
♦ TDC adjustment bar - 2068A-
♦ Setting tool - T40271-
Preparing tool
– Remove retaining ring -2- and take knurled screw -1- out of
TDC adjustment bar - 2068A- .
2. Chain drive 105

– Remove circlip -2- and take knurled screw -1- out.
– Slide knurled screw -1- from tool -T40271/1- into TDC adjust‐
ment bar - 2068A- , as shown in illustration.
Procedure
• Timing chain removed from camshafts.
• Camshafts for cylinder bank 2 (left-side) installed.
• Inlet camshaft of cylinder bank 2 (left-side) locked at “TDC” by
• Backlash compensation assembly of inlet camshaft for cylin‐

der bank 2 (left-side) locked in place with adjustment pin -
T40313- . The teeth of the two gears of inlet camshaft must
align ⇒ page 140 .

– Align flange -3- with eccentric washer -4- of intermediate drive.

• Marking -1- should align with notch -2-.
– Fit intermediate drive on cylinder head.
• Marking -1- and notch -2- must align with cast projection
-arrow- on cylinder head.
– Screw in bolt -5- for intermediate drive by hand until it makes
contact.
• It should just be possible to turn the eccentric washer of the
intermediate drive without axial movement.
– Turn eccentric washer -1- anti-clockwise -arrow- as far as

stop.
– Secure TDC adjustment bar - 2068 A- to cylinder head using
knurled screw -3-, as shown in illustration.
– Align caliper gauge of TDC adjustment bar - 2068A- with
marking -4- on eccentric washer, as shown in illustration, then
secure with locking bolt -2-.
– Turn eccentric washer -1- clockwise -arrow- until notch -3- is

aligned with TDC adjustment bar - 2068A- , as illustrated.
– Tighten bolt -2-, ensuring that eccentric washer remains in
setting position.
Note
On some versions, there is no line marking on the eccentric wash‐

er. If this is the case, a mark -2- must be made at a distance -a-
= 5.2 mm to the right of the notch -1-.
2. Chain drive 107

3 Cylinder head
⇒ “3.1 Exploded view - cylinder head”, page 108
⇒ “3.2 Exploded view - cylinder head cover”, page 110
⇒ “3.3 Removing and installing cylinder head”, page 114
⇒ “3.4 Removing and installing cylinder head cover”, page 121
⇒ “3.5 Removing and installing seals for injectors”, page 125
⇒ “3.6 Checking compression”, page 126
3.1 Exploded view - cylinder head
1 - Cylinder head gasket

❑ Identification
⇒ page 109
part number must face
cylinder head
❑ If renewed, change
coolant and engine oil
2 - Bolt
❑ For
❑ 23 Nm
3 - Bracket
❑ Not fitted on all models
4 - O-ring
5 - Coolant pipe
6 - Bolt
❑ 9 Nm
7 - Seal
8 - Bolt
❑ 23 Nm
9 - Engine lifting eye
10 - O-ring
11 - Coolant pipe
12 - Bolt
❑ Tightening torque ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes;
Exploded view - coolant pipes
13 - Bolt
❑ Correct sequence when slackening ⇒ page 115


15 - Bolt
❑ 23 Nm
16 - Cylinder head
❑ Shown for cylinder bank 2 (left-side)
❑ To prevent damage to glow plugs, always place cylinder head on a soft foam surface after removal.
❑ Checking for distortion ⇒ page 109
❑ Cylinder heads must not be reworked on TDI engines
❑ If renewed, change coolant and engine oil
Checking cylinder head for distortion

– Use straight edge 500 mm - VAS 6075- and feeler gauge to
measure cylinder head for distortion at several points.
• Max. permissible distortion: 0.1 mm.
• Cylinder heads must not be reworked on TDI engines.
Identification of cylinder head gasket

1- Part number
2- Holes
Note
♦ Cylinder head gaskets of different thicknesses are fitted de‐

pending on the amount of piston projection ⇒ page 61 . If
renewing the cylinder head gasket only, the new gasket should
have the same identification as the old one.
♦ The gaskets for the left and right cylinder heads have different
Cylinder head - tightening torque and sequence

2. -1 … 8- 35 Nm
3. -1 … 8- 50 Nm
3. Cylinder head 109

3.2 Exploded view - cylinder head cover

⇒ “3.2.1 Exploded view - aluminium cylinder head cover”,
page 110
⇒ “3.2.2 Exploded view - plastic cylinder head cover”, page 112
3.2.1 Exploded view - aluminium cylinder head cover
1 - Gasket
❑ For cylinder head cover
❑ Renew if damaged or
leaking
2 - O-ring
❑ 8x
3 - Cylinder head cover
❑ Shown for cylinder bank
2 (left-side)
stalling cylinder head
cover”, page 121
4 - Nut
sequence:
♦ ⇒ Fig. ““Aluminium cylinder
head cover, bank 1 (right-
side) - tightening torque
and sequence”“ ,
page 111
♦ ⇒ Fig. ““Aluminium cylinder
head cover, bank 2 (left-
page 111
5 - O-ring
6 - Bolt
❑ 9 Nm
7 - Oil filler neck
8 - Grommet
9 - Seal
❑ For filler cap
❑ Renew if damaged or leaking
10 - Filler cap
11 - Grommets
12 - Seal
❑ For injector
13 - Copper seal

14 - O-ring
15 - Clamping piece
❑ Removing and installing ⇒ “5.8 Removing and installing injectors”, page 255
16 - Bolt
17 - Injector
❑ Observe rules for cleanliness ⇒ page 7
18 - Bracket
19 - Bolt
❑ 7.5 Nm
20 - Bolt
❑ With seal
❑ Tightening torque and sequence:
♦ ⇒ Fig. ““Aluminium cylinder head cover, bank 1 (right-side) - tightening torque and sequence”“ , page 111
♦ ⇒ Fig. ““Aluminium cylinder head cover, bank 2 (left-side) - tightening torque and sequence”“ , page 111
Aluminium cylinder head cover, bank 1 (right-side) - tightening

torque and sequence
– Tighten bolted connections in stages in the sequence shown:
Stage Bolts, nuts, ball Tightening torque
studs
2. -1 … 11- 9 Nm
Aluminium cylinder head cover, bank 2 (left-side) - tightening tor‐

que and sequence
studs
2. -1 … 11- 9 Nm

Bracket for SCR supply line - tightening torque

– Tighten bolt -arrow- to 9 Nm.
3.2.2 Exploded view - plastic cylinder head cover
1 - Gasket
❑ For cylinder head cover
❑ Renew if damaged or
leaking
2 - O-ring
❑ 8x
2 (left-side)
stalling cylinder head
cover”, page 121
4 - Nut
sequence:
♦ ⇒ Fig. ““Plastic cylinder
head cover, bank 1 (right-
page 113
♦ ⇒ Fig. ““Plastic cylinder
head cover, bank 2 (left-
page 114
5 - O-ring
6 - Bolt
❑ Thread-forming
❑ Fit and screw in bolt by
hand so that it is
screwed into old thread. Then tighten bolt to torque
❑ 5 Nm
7 - Oil filler neck
8 - Grommet
9 - Seal
❑ For filler cap


10 - Filler cap
11 - Grommets
12 - Seal
❑ For injector
13 - Copper seal
14 - O-ring
15 - Injector
❑ Observe rules for cleanliness ⇒ page 7
16 - Clamping piece
❑ Removing and installing ⇒ “5.8 Removing and installing injectors”, page 255
17 - Bolt
18 - Bracket
19 - Bolt
❑ Thread-forming
❑ Fit and screw in bolt by hand so that it is screwed into old thread. Then tighten bolt to torque
❑ 6 Nm
20 - Bolt
❑ With seal
❑ Tightening torque and sequence:
♦ ⇒ Fig. ““Plastic cylinder head cover, bank 1 (right-side) - tightening torque and sequence”“ , page 113
♦ ⇒ Fig. ““Plastic cylinder head cover, bank 2 (left-side) - tightening torque and sequence”“ , page 114
21 - Bolt
❑ 6 Nm
22 - Bracket
❑ For SCR supply line
Plastic cylinder head cover, bank 1 (right-side) - tightening torque

and sequence
studs
2. -1 … 11- 8 Nm

Plastic cylinder head cover, bank 2 (left-side) - tightening torque

and sequence
studs
2. -1 … 11- 8 Nm
3.3 Removing and installing cylinder head

⇒ “3.3.1 Removing cylinder head - bank 1 (right-side)”,
page 114
⇒ “3.3.2 Removing cylinder head - bank 2 (left-side)”, page 116
⇒ “3.3.3 Installing cylinder head”, page 118
3.3.1 Removing cylinder head - bank 1 (right-

side)
Procedure
– Remove intake manifold (top section) ⇒ page 228 .
– Remove camshaft timing chain from camshaft timing chain
sprockets
⇒ “2.5 Removing camshaft timing chain from camshafts”, page
81 .
– Remove camshafts (right-side)
⇒ “4.4 Removing and installing camshaft”, page 136 .
Note
♦ If bolt -arrow- has been loosened, backlash must be re-adjus‐

ted ⇒ page 101 .
♦ Only loosen bolt when renewing cylinder head and fitting in‐
termediate drive on new cylinder head.
– Unbolt coolant pipe (front) and disconnect from thermostat

housing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail;
Rep. gr. 19 ; Coolant pipes; Removing and installing coolant
pipes .

– Remove bolts -arrows- and move coolant connection -1- to

one side.
– Remove bolts -arrows- and move coolant pipe (top right) -1-
to side.
– Remove bolt -2- from retaining clamp for high-pressure pipe.
– Remove guide pin -1-.

– Secure clamp -T40309/2- to cylinder head with fitted bolt -
T40309/3- , as shown in illustration.
– Support tensioning rail by tightening knurled screw -3- of
bracket -T40309/1- until clamp -T40309/2- makes contact with
tensioning rail.
– Loosen guide pin -2- and unscrew it by hand.
Note
To avoid damaging the thread in the cylinder head, it must be

possible to unscrew the guide bolt for the tensioning rail easily. If
necessary, tighten knurled screw -3- further slightly.
– Loosen knurled screw -3-, unscrew fitted bolt -T40309/3- and

detach clamp -T40309/2- .
– Slacken cylinder head bolts in the sequence -1 ... 8-.

– Remove bolts and carefully take off cylinder head.
Caution
Risk of damage to glow plugs when putting down cylinder

head.
♦ After removal, the cylinder head must not be put down on
the gasket side with the glow plugs still installed, because
the glow plugs project slightly beyond the gasket surface.
– Seal off all open passages in the intake and exhaust system
with clean cloths or plugs (thoroughly cleaned) from engine
bung set - VAS 6122- .

3.3.2 Removing cylinder head - bank 2 (left-

side)
Procedure
– Remove camshaft timing chain from camshaft timing chain
sprockets
⇒ “2.5 Removing camshaft timing chain from camshafts”, page
81 .
– Remove camshafts (left-side)
Note

ted ⇒ page 105 .
– Release hose clip -arrow- and disconnect coolant hose for in‐
jector for reducing agent - N474- .

– Remove bolts -arrows- and move coolant connection -1- to

one side.
– If fitted, remove bolt -2- at retaining clamp for vacuum line.
– Slacken cylinder head bolts in the sequence -1 ... 8-.

– Remove bolts and carefully take off cylinder head; pay atten‐
tion to vacuum hoses and electrical wiring.
Caution
Risk of damage to glow plugs when putting down cylinder

head.
♦ After removal, the cylinder head must not be put down on
the gasket side with the glow plugs still installed, because
the glow plugs project slightly beyond the gasket surface.
– Seal off all open passages in the intake and exhaust system
with clean cloths or plugs (thoroughly cleaned) from engine
bung set - VAS 6122- .

3.3.3 Installing cylinder head

Procedure
Note

ted ⇒ page 105 .
♦ Illustration shows the intermediate drive for cylinder bank 2
(left-side) as an example.
Caution
Risk of damage to sealing surfaces.

♦ Carefully remove sealant residue from cylinder head and
cylinder block.
♦ Ensure that no long scores or scratches are made on the
surfaces.
Risk of damage to cylinder block.
♦ No oil or coolant must be allowed to remain in the blind
holes for the cylinder head bolts in the cylinder block.
Risk of leaks at cylinder head gasket.
♦ Carefully remove any remaining emery and abrasive ma‐
terial.
♦ Do not remove new cylinder head gasket from packaging
until it is ready to be fitted.
♦ Handle the cylinder head gasket very carefully to prevent
damage to the silicone coating or the indented area of the
gasket.
Risk of damage to open valves.
♦ When installing an exchange cylinder head, the plastic
protectors fitted to protect the open valves should not be
removed until the cylinder head is ready to be fitted.
Risk of damage to valves and piston crowns after working on
valve gear.
♦ Turn the engine carefully at least 2 rotations to ensure that
none of the valves make contact when the starter is op‐
erated.

Note

angle.
♦ Renew self-locking nuts, as well as seals, gaskets and O-rings
after removing.
♦ Cylinder heads must not be reworked on TDI engines.
♦ When installing an exchange cylinder head, the contact sur‐
faces between roller rocker fingers and cams must be oiled
before installing the cylinder head cover.
♦ After fitting a new cylinder head or cylinder head gasket,
change engine oil and coolant in entire cooling system.
– Note cylinder head gasket identification:

1- Part number
2- Holes
Note
♦ If the cylinder head gasket or cylinder head have been re‐

newed, select the new cylinder head gasket according to the
number of holes on the old gasket.
♦ If parts of the crankshaft drive have been renewed, select the
new cylinder head gasket by measuring the piston projection
at “TDC” ⇒ page 61 .
♦ The gaskets for the left and right cylinder heads have different
– Place cylinder head gasket in position.

• Pay attention to dowel sleeves -arrows- in cylinder block.
• Installation position of cylinder head gasket: the word
“oben” (top) or the part number should face towards the cyl‐
inder head.
– Fit cylinder head.
– Tighten cylinder head bolts ⇒ page 109 .
Note
Cylinder head bolts do not have to be torqued down again later

after repair work.

note the following:

Cylinder head, bank 1 (right-side):

– Screw in and tighten guide pin -1- for guide rail by hand.
– Secure clamp -T40309/2- to cylinder head with fitted bolt -
T40309/3- , as shown in illustration.
– Align tensioning rail with threaded hole for guide pin in cylinder
head; to do so, screw in knurled screw -3- of bracket T40309/1
until clamp -T40309/2- adjusts tensioning rail into installation
position.
– Screw in and tighten guide pin -2- by hand.
Note
To avoid damaging the thread in the cylinder head, it must be

possible to screw in the guide bolt for the tensioning rail easily. If
necessary, tighten or loosen fitted bolt -T40309/3- further slightly.
– Loosen knurled screw -3-, unscrew fitted bolt -T40309/3- and

detach clamp -T40309/2- .
– Install coolant pipe (front and top right) ⇒ 6-cylinder TDI en‐
gine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes;
Removing and installing coolant pipes .
Both sides (continued):
– Install camshafts
Note
If the cylinder head was renewed, you must install the intermedi‐
ate drive and re-adjust the backlash ⇒ page 101 .
– Install camshaft timing chain ⇒ page 81 .

– Install intake manifold (top section) ⇒ page 228 .
– Change coolant ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve com‐
mon rail; Rep. gr. 19 ; Cooling system/coolant; Draining and
filling cooling system .
ltr. 4-valve common rail; Rep. gr. 15 ; Cylinder head; Removing
and installing cylinder head .
Tightening torques
♦ ⇒ Fig. ““Cylinder head - tightening torque and sequence”“ ,
page 109

3.4 Removing and installing cylinder head

cover
⇒ “3.4.1 Removing cylinder head cover - bank 1 (right-side)”, page
121
⇒ “3.4.2 Removing cylinder head cover - bank 2 (left-side)”, page
122
⇒ “3.4.3 Installing cylinder head cover”, page 124
3.4.1 Removing cylinder head cover - bank 1

(right-side)
Removing
Cylinder head; Removing and installing cylinder head cover .
– Remove high-pressure reservoir (rail) ⇒ page 267 .
– Remove injectors ⇒ page 255 .
– Unplug electrical connector for Hall sender - G40- -item 1-.
trical wiring harness clear at cylinder head cover using remov‐
al lever - 80-200- .

– Press release tabs on both sides and disconnect crankcase

breather hose -2-.
– Remove bolts -arrows- and detach resonator -1-.
– If necessary, remove bolt -arrow- and detach engine lifting eye

-1-.
– If necessary, unplug electrical connector -arrow-.

– If fitted, detach noise insulation.
– Use a vacuum cleaner to remove any residue left by the noise
insulation.
– Loosen bolts in the sequence -11 … 1-; to do so, counterhold

at centre hex studs for camshaft bearing caps. (Illustration
shows aluminium cylinder head cover.)
– Remove cylinder head cover; pay attention to electrical wiring
and noise insulation for electric compressor if necessary.
Installing ⇒ “3.4.3 Installing cylinder head cover”, page 124
3.4.2 Removing cylinder head cover - bank 2

(left-side)

Removing
Cylinder head; Removing and installing cylinder head cover .
– Remove high-pressure reservoir (rail) ⇒ page 267 .
– Remove injectors ⇒ page 255 .
– Remove intake manifold flap motor - V157- ⇒ page 234 .
– Unscrew bolt -2- and release screw-type clip.
– Detach injector for reducing agent - N474- -item 1- and place
to one side.
– Unplug electrical connectors on glow plugs for cylinder bank
2 (left-side).
– Unplug electrical connector -1-.

– Remove bolt -2- and move pressure differential sender 2 -
G524- clear.

– Detach electrical connector -3- for exhaust gas recirculation

temperature sensor - G98- -item 2- from bracket, unplug and
move electrical wiring clear.
– Move electrical wiring and SCR supply line clear.
– Detach noise insulation.
insulation.
– Loosen bolts in the sequence -11 … 1-; counterhold at centre

hex studs for camshaft bearing caps (shown on aluminium
cylinder head cover).
– Remove cylinder head cover; pay attention to electrical wiring
and noise insulation for electric compressor if necessary.
Installing ⇒ “3.4.3 Installing cylinder head cover”, page 124
3.4.3 Installing cylinder head cover

Procedure
Note
♦ Renew O-rings after removing.

♦ Renew gasket for cylinder head cover if damaged.
Note
– Cut off nozzle of tube at front marking (nozzle ∅ approx.

2 mm).

– Apply sealant bead -arrows- at each joint between cylinder

head and timing chain cover (top left).
• Width of sealant beads: approx. 2 mm.
– Tighten bolts and nuts for cylinder head cover.
– If previously removed, install intake manifold flap motor -
V157- ⇒ page 234 .
– Install injectors ⇒ page 255 .
– Install high-pressure reservoir (rail) ⇒ page 267 .
– Check fuel system for leaks ⇒ page 218 .
ltr. 4-valve common rail; Rep. gr. 15 ; Cylinder head; Removing
and installing cylinder head cover .
Tightening torques
♦ ⇒ Fig. ““Aluminium cylinder head cover, bank 1 (right-side) -
tightening torque and sequence”“ , page 111
♦ ⇒ Fig. ““Aluminium cylinder head cover, bank 2 (left-side) -
tightening torque and sequence”“ , page 111
♦ ⇒ Fig. ““Plastic cylinder head cover, bank 1 (right-side) - tight‐
ening torque and sequence”“ , page 113
♦ ⇒ Fig. ““Plastic cylinder head cover, bank 2 (left-side) - tight‐
ening torque and sequence”“ , page 114
♦ Body brace ⇒ Running gear, axles, steering; Rep. gr. 40 ;
Suspension strut, upper links; Exploded view - suspension
strut, upper links
3.5 Removing and installing seals for injec‐

tors
♦ Carrier - 3390-
♦ Pliers -VAS 211 007- (not illustrated)

Procedure
• Injector removed ⇒ page 255 .

– Pull off seal -1- using pliers -VAS 211 007- -arrow-.
– Drive in new injector seal as far as stop using socket, AF 24 -

T10361- and short extension -1-.
– Install injector ⇒ page 255 .
3.6 Checking compression

♦ Compression tester - V.A.G 1763- with adapter - V.A.G
1763/8-
Procedure
• Engine oil temperature approx. 30° C
• Battery voltage at least 12.5 V
Caution
Incorrect handling of ceramic glow plugs can cause engine

damage.
♦ Observe safety precautions ⇒ page 5 .
– Remove all glow plugs ⇒ page 322 .

– Unplug electrical connector -arrow- at fuel pressure regulating

valve - N276- on high-pressure reservoir (rail) (cylinder bank
1, right-side).
– Briefly start engine to relieve fuel pressure in high-pressure
reservoir (rail).
– Screw in adapter - V.A.G 1763/8- in place of corresponding

glow plug and connect compression tester - V.A.G 1763- .
(Using the compression tester ⇒ Operating instructions .)
– Have a second mechanic operate starter until tester shows no
further pressure increase.
– Repeat procedure on each cylinder.
Compression pressure bar
When new 28 … 33
Wear limit 21
Maximum difference between cylinders 5
Assembling
Assembly is performed in reverse sequence; note the following:
– Install glow plugs ⇒ page 322 .
– Erase any entries in engine control unit event memory result‐
ing from work performed ⇒ Vehicle diagnostic tester.

4 Valve gear
⇒ “4.1 Exploded view - valve gear”, page 128
⇒ “4.2 Measuring axial clearance of camshaft”, page 134
⇒ “4.3 Measuring radial clearance of camshaft”, page 135
⇒ “4.4 Removing and installing camshaft”, page 136
⇒ “4.5 Removing and installing valve stem oil seals”, page 149
4.1 Exploded view - valve gear
1 - Valve
❑ Do not machine, only
grinding-in is permitted
❑ Checking ⇒ page 158
❑ Valve dimensions
⇒ page 158
❑ Checking valve guides
⇒ page 157
2 - Cylinder head
2 (left-side)
❑ Checking valve guides
⇒ page 157
❑ Machining valve seats
⇒ page 157
3 - Valve stem oil seal
4 - Valve spring
5 - Valve spring plate
6 - Hydraulic compensation el‐
ement
❑ Clipped into roller rocker
finger -item 9-
❑ Lubricate contact surfa‐
ces before installing
7 - Securing clip
❑ Not supplied separately
❑ Check for firm attach‐
ment
8 - Roller rocker finger
❑ Mark installation position for re-installation
❑ Check roller bearings for ease of movement
❑ Lubricate contact surfaces before installing
❑ Assembly: attach to hydraulic compensation element -item 7- using securing clip -item 8-

9 - Valve cotters
10 - Dowel sleeves
❑ Only for bearing cap (gearbox end) with camshaft thrust bearing
11 - Bearing pedestal
❑ Removing and installing ⇒ “4.4 Removing and installing camshaft”, page 136
12 - Inlet camshaft
❑ Allocation ⇒ Electronic parts catalogue
❑ Measuring axial clearance ⇒ page 134
❑ Runout: max. 0.01 mm
13 - Support bracket
❑ For clamping piece
❑ Only for cylinder bank 1 (right-side)
❑ Clean threads and threaded holes; they must be free of oil and grease
14 - Thrust bearing
15 - Bearing cap
❑ Removing and installing ⇒ “4.4 Removing and installing camshaft”, page 136
16 - Bolt
❑ With shoulder for clamping piece
17 - Bolt
18 - Centre hex stud
❑ With shoulder for clamping piece
19 - Thrust bearing
20 - Exhaust camshaft
❑ Allocation ⇒ Electronic parts catalogue
❑ Removing and installing ⇒ “4.4.1 Removing and installing camshaft”, page 136
❑ Renewing ⇒ “4.4.2 Renewing camshaft”, page 145
❑ Measuring axial clearance ⇒ page 134
❑ Runout: max. 0.01 mm
21 - Dowel sleeves
❑ Only for bearing pedestal (gearbox end) with camshaft thrust bearing
4. Valve gear 129

A - camshaft bearing - tightening torque and sequence, method

1
These instructions apply to:
• Timing chain detached from camshaft chain sprocket
• Intermediate drive removed
Note
Clean threads and threaded holes; they must be free of oil and
grease.

Stage 1
Bolts Tightening torque
-1 … 4- Screw in by hand until bolt heads make con‐
tact with bearing caps
– Only if intermediate drive is installed: Check that splines of

camshaft -4- and intermediate drive -5- mesh. If necessary,
push down mounting bracket -2- with your hand and screw in
bolt -3- by hand until it makes contact.
WARNING
The components of the backlash compensation assembly are

under spring tension. This can cause injury.
♦ Do NOT remove locking pin - T10060A- .
♦ Do NOT remove assembly aid -1- (only for new cam‐
shafts).
♦ Do NOT remove adjustment pin - T40313- (for re-installing
used camshafts).
Caution
Risk of excess strain when tightening camshaft bearings.

♦ Do NOT remove cable ties -6-.
Stage 2
-1 … 4- Continue tightening 1 turn at a time in several
stages until all bearing caps make full con‐
tact with cylinder head and a torque of 3 Nm
is reached
-1 … 4- 3 Nm

Stage 3
-1 … 8- 3 Nm
Stage 4
-1 … 4- 3 Nm (this step is performed to allow for set‐
tling of components)
Stage 5
-1 … 12- 3 Nm
-1 … 12- Turn 45° further
Roller rocker fingers - installation position
Caution
Risk of engine damage if roller rocker fingers are installed in‐

correctly.
♦ Check that roller rocker fingers are installed in the correct
position.
– Remove cable ties.
4. Valve gear 131

B - camshaft bearing - tightening torque and sequence, method

2
These instructions apply to:
• Timing chain drive fully installed
Note
grease.

Stage 1
-1 … 4- Screw in by hand until bolt heads make con‐
tact with bearing caps
– Check that splines of camshaft -4- and intermediate drive -5-

mesh. If necessary, push down mounting bracket -2- with your
hand and screw in bolt -3- by hand until it makes contact.
– Remove locking pin - T10060A- .
– If a new camshaft is being installed, detach assembly aid -1-.
– If a used camshaft is being re-installed, remove adjustment
pin - T40313- .
Caution
Risk of excess strain when tightening camshaft bearings.

♦ Do NOT remove cable ties -6-.
Stage 2
-1 … 4- Continue tightening 1 turn at a time in several
stages until all bearing caps make full con‐
tact with cylinder head and a torque of 3 Nm
is reached
-1 … 4- 3 Nm

Stage 3
-1 … 8- 3 Nm
Stage 4
-1 … 4- 3 Nm (this step is performed to allow for set‐
tling of components)
Stage 5
-1 … 12- 3 Nm
-1 … 12- Turn 45° further
Roller rocker fingers - installation position
Caution
Risk of engine damage if roller rocker fingers are installed in‐

correctly.
♦ Check that roller rocker fingers are installed in the correct
position.
– Remove cable ties.
4. Valve gear 133

4.2 Measuring axial clearance of camshaft

Procedure
– Remove camshafts ⇒ page 136 .
– Mark allocation of roller rocker fingers for re-installation.
– Carefully remove roller rocker fingers and place them on a
clean surface.
– Move camshafts into installation position and tighten bolts on
outer camshaft bearings to 9 Nm.

– Lock backlash compensation assembly of inlet and exhaust

camshafts into place with adjustment pin - T40313- .
• Teeth of the two gears of exhaust camshaft must align
⇒ page 139 .
Note
Exhaust camshaft for cylinder bank 1 (right-side) is shown as an

example.
– Secure dial gauge - VAS 6079- with universal dial gauge

bracket - VW 387- to cylinder head as shown in illustrations.
Axial clearance (inlet camshaft)
• Specification: 0.0682 … 0.0750 mm.
Axial clearance (exhaust camshaft)

• Specification: 0.0682 … 0.0750 mm.
4.3 Measuring radial clearance of camshaft

♦ Plastigauge
Procedure
– Remove camshafts ⇒ page 136 .
– Mark allocation of roller rocker fingers for re-installation.
– Carefully remove roller rocker fingers and place them on a
clean surface.
– Clean bearings and bearing journals.
4. Valve gear 135


bearing on the bearing journal or bearing shell to be measured.
• The Plastigauge must be positioned in the centre of the bear‐
ing.
– Re-insert camshafts with camshaft bearings and tighten with‐
out rotating camshafts.
– Remove camshafts with camshaft bearings again.
Radial clearance:
• New: 0.037 ... 0.063 mm.
4.4 Removing and installing camshaft

⇒ “4.4.1 Removing and installing camshaft”, page 136
⇒ “4.4.2 Renewing camshaft”, page 145
4.4.1 Removing and installing camshaft

♦ Open-end spanner 16 mm - T10447-

♦ Wrench, 21 mm - T40263-
Removing
Valve gear; Removing and installing camshaft .
4. Valve gear 137

– Remove corresponding cylinder head cover

⇒ “3.4 Removing and installing cylinder head cover”,
page 121 .
– Remove noise insulation (front)/one-piece noise insulation ⇒
frame cross brace .
Note

Caution

slips.
-arrow-.
– Use wrench, 21 mm - T40263- and adapter -T40314- to turn

crankshaft until vibration damper is at “TDC” position. (Illus‐
tration shows vehicle with alternator.)
• Mark (stuck on) -1- must be vertical and aligned with arrow
marking on coolant pump.


Caution


T10060A- . If not, turn crankshaft 360° further in direction of
engine rotation.
Camshafts for cylinder bank 1 (right-side):
Note
If exhaust camshaft of cylinder bank 1 (right-side) cannot be

locked, use open-end spanner (16 mm) - T10447- to turn cam‐
shaft chain sprocket slightly back and forth, as shown.
– Lock backlash compensation assembly of exhaust camshaft

in place by inserting adjustment pin - T40313- into sprocket as
far as groove -arrow- and turning it 90° anti-clockwise.
4. Valve gear 139

Camshafts for cylinder bank 2 (left-side):

Note
If inlet camshaft of cylinder bank 2 (left-side) cannot be locked,

use open-end spanner (16 mm) - T10447- to turn camshaft chain
sprocket slightly back and forth, as shown.
– Lock backlash compensation assembly of inlet camshaft in

place by inserting adjustment pin - T40313- into sprocket as
far as groove -arrow- and turning it 90° anti-clockwise.


– Wrap one cable tie -arrows- on each side around bearing ped‐
estal and bearing cap and secure.
Note
♦ Fit cable ties tightly, aligning them so that bolts on bearing cap
can be slackened/tightened.
♦ With the cable ties it is possible to detach the camshafts to‐
gether with the camshaft bearings. This prevents components
from being interchanged and ensures that the “TDC” position
is maintained.
Note
Mark allocation of bolts for re-installation.
– Unscrew bolts in several stages one turn at a time in sequence

-12 ... 1- until all camshaft bearings are clear.
Note
Make sure you do not damage the roller rocker fingers and hy‐
draulic compensation elements when removing the camshafts.
– Carefully detach camshaft bearings together with camshafts.
Caution
Do NOT interchange components!

♦ Do not release cable ties until after re-installation.
– If necessary for additional work, mark roller rocker fingers and

hydraulic compensation elements for re-installation, remove
them and place them on a clean surface.
Installing
Note
grease.
4. Valve gear 141

Requirements
T40237- .
• Exhaust camshaft for cylinder bank 1 (right-side) and inlet

camshaft for cylinder bank 2 (left-side) locked at “TDC” by in‐
serting locking pin - T10060A- in hole.
• Backlash compensation assembly of exhaust camshaft for

cylinder bank 1 (right-side) and inlet camshaft for cylinder bank
2 (left-side) locked in place with adjustment pin - T40313- .
Note
New camshafts are supplied with an assembly aid which is inser‐

ted in place of the adjustment pin -T40313- .

– Check installation position of dowel sleeves:

• Dowel sleeves -arrows- must be inserted in holes in bearing
pedestals “X4” and “X2” ⇒ page 147 .
• Dowel sleeves must engage in holes in cylinder head.
WARNING

♦ Do NOT remove locking pin - T10060A- .
♦ Do NOT remove assembly aid -1- (only for new cam‐
shafts).
♦ Do NOT remove adjustment pin - T40313- (for re-installing
used camshafts).
– Fit camshafts and camshaft bearings (secured with cable ties

-arrows-) on cylinder head.
Note
The cable ties help to keep the camshafts and camshaft bearings
straight when they are tightened, and to keep both camshafts in
“TDC” position respective to one another.
– Push bearing mounting “X4” -item 1- down fully by hand until

it makes contact with cylinder head; pay attention to dowel
sleeve when doing so.
♦ Doing this ensures that the fitting sleeves reach their installa‐
tion position in the cylinder head, and that, if the intermediate
drive is installed, the splines of the exhaust camshaft for cyl‐
inder bank 1 (right-side) and the inlet camshaft for cylinder
bank 2 (left-side) engage in the splines of the intermediate
drive.
♦ At the same time, the front part of the bearings is lifted by dis‐
tance -a-, as shown for bearing “X1” -item 2-.
♦ Tightening the bolts against the tension of the valve springs
will bring the front three bearings into a position where they
make contact.
– Tighten bolts for camshaft bearings:
♦ Timing chain drive fully installed ⇒ page 132
♦ Timing chain removed from camshaft sprocket, or intermedi‐
ate drive removed ⇒ page 130
4. Valve gear 143

Checking valve timing (complete timing chain drive must be in‐

stalled during check):
Caution

slips.
-arrow-.
– Turn crankshaft two rotations until vibration damper is at

“TDC” position again.

Caution


at “TDC”.
T10060A- .



Note
The timing adjustment is O.K. even if locking pin -T10060A- is

difficult to insert or if a 3.5 mm ∅ drill bit can be inserted instead
of locking pin - T10060A- (wrap insulating tape around the tip and
sharp edges of the drill bit to protect against injury).

note the following:
– Remove locking pin - T40237- .
– Install cylinder head cover
⇒ “3.4 Removing and installing cylinder head cover”,
page 121 .
ltr. 4-valve common rail; Rep. gr. 15 ; Valve gear; Removing and
installing camshaft .
Caution
Risk of damage to valves and piston crowns after working on

valve gear.
♦ The hydraulic tappets have to settle; wait for approx. 30
minutes after installing camshafts before starting engine.
♦ Turn the engine carefully at least 2 rotations to ensure that
none of the valves make contact when the starter is op‐
erated.
Tightening torques
♦ ⇒ “4.1 Exploded view - valve gear”, page 128
4.4.2 Renewing camshaft

4. Valve gear 145

Removing
– Remove camshafts
⇒ “4.4.1 Removing and installing camshaft”, page 136 and
place them on a clean surface.
– Lock backlash compensation assembly of inlet camshaft for
cylinder bank 1 (right-side) and exhaust camshaft for cylinder
bank 2 (left-side) in place by inserting adjustment pin -
T40313- into sprocket as far as groove -arrow- and turning it
90° clockwise.
Note
The backlash compensation assembly of the exhaust camshaft

for cylinder bank 1 (right-side) and inlet camshaft for cylinder bank
2 (left-side) was locked in place with adjustment pins -T40313-
during removal and must remain locked in place.
Caution
Warning! Risk of damage to engine.

♦ Check markings on bearing caps and bearing pedestals,
as shown below.
♦ Mark bearing caps and bearing pedestals if no markings
have yet been made.
– Remove cable ties from camshaft bearings.

– Remove locking pin - T10060A- .
– Detach bearing caps -3- from bearing pedestals -1-.

– Remove camshafts and detach thrust bearings -2, 4-.
• Thrust bearings are only installed on mounting bracket “X2”
⇒ page 147 .
– Remove adjustment pin - T40313- from camshaft being re‐
newed.

Installing
To prevent installation at the wrong locations, the camshaft bear‐
ing pedestals and bearing caps are marked:
• Backlash compensation assembly of camshaft sprockets
locked in place with adjustment pin - T40313- (for re-installing
used camshafts) / assembly aid (for installing new camshafts)
• Exhaust side markings: Markings on camshaft bearings face
exhaust manifolds on left and right.
• Rear markings: Markings on camshaft bearings face rear‐

wards towards camshaft sprockets.
Allocation of camshaft bearings

Cylinder bank 1 (right-side) Cylinder bank 2 (left-side) Installation position
R1/R1 L1/L1 Front
R2/R2 L2/L2 Front centre
R3/R3 L3/L3 Rear centre
R4/R4 L4/L4 Rear
– Place bearing pedestals on a clean surface, paying attention

to allocation ⇒ page 147 .
– Place camshafts onto bearing pedestals, paying attention to
markings.
4. Valve gear 147

Cylinder bank 1 (right-side):

• Marking -A- for inlet camshaft must be between the two mark‐
ings -B- for exhaust camshaft, as shown in illustration.
– Lock exhaust camshaft at “TDC” by inserting locking pin -
T10060A- in hole.
Cylinder bank 2 (left-side):
• Marking -A- for exhaust camshaft must be between the two
markings -B- for inlet camshaft, as shown in illustration.
– Lock inlet camshaft at “TDC” by inserting locking pin -
T10060A- in hole.

– Bring thrust bearings -2, 4- into installation position on cam‐
shafts.
– Place bearing cap -3- onto bearing pedestal -1-, paying atten‐
tion to allocation.
• Both dowel sleeves -arrows- must be inserted in holes in bear‐
ing pedestal “X2”.
• Dowel sleeves must engage in holes in bearing cap.
Note
New camshafts are supplied with an assembly aid -1- which is

inserted in place of the adjustment pin -T40313- .
– Wrap one cable tie -arrows- on each side around bearing ped‐
estal and bearing cap and secure.
Note
The cable ties help to keep the camshafts and camshaft bearings
straight when they are tightened.
– Remove assembly aid -1- from inlet camshaft for cylinder bank
1 (right-side)/exhaust camshaft for cylinder bank 2 (left-side).
WARNING

♦ Do NOT remove assembly aid -2- from exhaust camshaft
for cylinder bank 1 (right-side) or inlet camshaft for cylinder
bank 2 (left-side).
⇒ “4.4.1 Removing and installing camshaft”, page 136 .

4.5 Removing and installing valve stem oil

seals
⇒ “4.5.1 Removing and installing valve stem oil seals (cylinder
head installed)”, page 149
⇒ “4.5.2 Removing and installing valve stem oil seals (cylinder
head removed)”, page 152
4.5.1 Removing and installing valve stem oil

seals (cylinder head installed)
♦ Valve stem seal puller - 3364-
♦ Valve stem oil seal fitting tool - 3365- for inlet side, or (de‐
pending on version/manufacturer of valve stem oil seal)
♦ Valve stem seal fitting tool - T40376/1-
4. Valve gear 149

♦ Removal and installation device for valve cotters - VAS 5161

A- with guide plate -VAS 5161 A/34- and sealing pin -VAS
5161/29-1-
♦ Assembly sleeve ⇒ Electronic parts catalogue

Procedure
– Remove all glow plugs ⇒ page 322 .
– Remove camshafts
– Set piston of appropriate cylinder to “bottom dead centre”.
– Fit guide plate -VAS 5161 A/34- onto cylinder head.
– Secure guide plate with screws -arrows-.
– Insert drift -VAS 5161/3A- into guide plate and use plastic-
headed hammer to release sticking valve cotters.
– Screw sealing pin -VAS 5161/29-1- into guide plate.

– Screw adapter -VAS 5161/11- hand-tight into corresponding
glow plug thread.

– Screw snap-in device -VAS 5161/6- with engaging fork -

VAS 5161/5- into guide plate.
– Insert assembly cartridge -VAS 5161/8A- in hole above valve
spring that is to be removed.
– Connect adapter to compressed air line using a commercially
available connection piece and apply constant air pressure.
• Minimum pressure: 6 bar
– Attach pressure fork -VAS 5161/2- to snap-in device and push
assembly cartridge down.
– At the same time, turn knurled screw of assembly cartridge
clockwise until tips engage in valve cotters.
– Move knurled screw back and forth slightly; the valve cotters
are thus forced apart and taken up by the assembly cartridge.
– Release pressure fork.
– Take off assembly cartridge with knurled spacer ring.
– Detach valve spring with valve spring plate.
– Pull off valve stem oil seal with valve stem seal puller - 3364- .
If the valve stem seal puller - 3364- cannot be used on some of

the valve stem oil seals due to the confined space, proceed as
follows:
– Knock out pin -arrow- of puller using a drift and remove impact
extractor attachment.
– Apply bottom section of puller -3364- to valve stem oil seal.

– Secure puller with a punch or roll-pin drift -1-, as shown in il‐
lustration.
– Apply assembly lever to puller and pull out valve stem oil seal
-arrow-.
4. Valve gear 151

• To avoid damaging new valve stem oil seal -4- during instal‐
lation, fit assembly sleeve -item 3- onto valve stem -2-.
– Lightly oil sealing lip of valve stem oil seal.
• Valve shaft seal fitting tool - 3365- or pusher - T40376/1- (de‐
pending on version/manufacturer of valve stem oil seal)
– Insert valve stem oil seal into valve shaft seal fitting tool - 3365-
and use assembly sleeve to carefully press it onto valve guide
-1- as far as stop.
– Remove assembly sleeve .
If valve cotters have been removed from assembly cartridge, they

must first be inserted in insertion device -VAS 5161/18- .
• Larger diameter of valve cotters faces upwards.
– Insert valve spring and valve spring plate.
– Press assembly cartridge onto insertion device from above
and pick up valve cotters.
– Insert assembly cartridge in guide plate -VAS 5161 A/34-

again.
– Press down pressure fork and pull knurled screw upwards
while turning screw in both directions - this will insert the valve
cotters.
– Release pressure fork with knurled screw still in pulled posi‐
tion.
– Repeat procedure for each valve.
Assembling
– Install glow plugs ⇒ page 322 .
4.5.2 Removing and installing valve stem oil

seals (cylinder head removed)

♦ Valve stem seal puller - 3364-
♦ Valve stem oil seal fitting tool - 3365- , or (depending on ver‐

sion/manufacturer of valve shaft seal):
♦ Valve stem seal fitting tool - T40376/1-
♦ Removal and installation device for valve cotters - VAS 5161

A- with guide plate -VAS 5161 A/34- and sealing pin -VAS
5161/29-1-
4. Valve gear 153

♦ Engine and gearbox support - VAS 6095A-
♦ Cylinder head tensioning device - VAS 6419-
♦ Assembly sleeve ⇒ Electronic parts catalogue

Procedure
– Insert cylinder head tensioning device - VAS 6419- into engine
and gearbox support - VAS 6095A- .
– Secure cylinder head in cylinder head tensioning device, as
shown in illustration.
– Connect cylinder head tensioning device to compressed air
supply.
– Using lever -arrow-, slide air pad under combustion chamber
where valve stem oil seal is to be removed.
– Apply just enough compressed air to bring air pad into contact
with valve heads.
– Mark fitting location of roller rocker fingers for re-installation
and remove.
– Fit guide plate -VAS 5161 A/34- onto cylinder head.

– Secure guide plate with screws -arrows-.
– Insert drift -VAS 5161/3A- into guide plate and use plastic-
headed hammer to release sticking valve cotters.

– Screw snap-in device -VAS 5161/6- with engaging fork -

VAS 5161/5- into guide plate.
– Insert assembly cartridge -VAS 5161/8A- in hole above valve
spring that is to be removed.
– Attach pressure fork -VAS 5161/2- to snap-in device and push
assembly cartridge down.
– At the same time, turn knurled screw of assembly cartridge
clockwise until tips engage in valve cotters.
– Move knurled screw back and forth slightly; the valve cotters
are thus forced apart and taken up by the assembly cartridge.
– Release pressure fork.
– Take off assembly cartridge with knurled spacer ring.
– Detach valve spring with valve spring plate.
– Pull off valve stem oil seal with valve stem seal puller - 3364- .
• To avoid damaging new valve stem oil seal -4- during instal‐
lation, fit assembly sleeve -item 3- onto valve stem -2-.
– Lightly oil sealing lip of valve stem oil seal.
• Use either valve shaft seal fitting tool - 3365- or valve shaft
seal fitting tool - T40376/1- (depending on version/manufac‐
turer of valve stem oil seal).
– Insert valve stem oil seal into valve shaft seal fitting tool -5-
and use assembly sleeve to press it carefully onto valve guide
-1- as far as stop.
– Remove assembly sleeve .
4. Valve gear 155

If valve cotters have been removed from assembly cartridge, they

must first be inserted in insertion device -VAS 5161/18- .
• Larger diameter of valve cotters faces upwards.
– Insert valve spring and valve spring plate.
– Press assembly cartridge onto insertion device from above
and pick up valve cotters.
– Insert assembly cartridge in guide plate -VAS 5161 A/34-

again.
– Press down pressure fork and pull knurled screw upwards
while turning screw in both directions - this will insert the valve
cotters.
– Release pressure fork with knurled screw still in pulled posi‐
tion.
– Repeat procedure for each valve.
Assembling
Assemble in reverse order.

5 Inlet and exhaust valves

⇒ “5.1 Machining valve seats”, page 157
⇒ “5.2 Checking valve guides”, page 157
⇒ “5.3 Checking valves”, page 158
⇒ “5.4 Valve dimensions”, page 158
5.1 Machining valve seats
Note
Valve seats may not be machined due to the very small toleran‐
ces.
5.2 Checking valve guides

Procedure
Note
♦ If the valve has to be renewed as part of a repair, use a new

valve for the measurement.
♦ Only insert inlet valve into inlet valve guide and exhaust valve
into exhaust valve guide, as the stem diameters are different.
5. Inlet and exhaust valves 157

– Attach dial gauge - VAS 6079- with universal dial gauge brack‐
et - VW 387- to cylinder head.
– Insert valve into guide.
• End of valve stem must be flush with valve guide.
– Measure the amount of sideways play.
• Wear limit: 1.0 mm.
– If the wear limit is exceeded, repeat the measurement with
new valves.
– Renew cylinder head if wear limit is still exceeded.
Note
Valve guides cannot be renewed.
5.3 Checking valves

– Visually inspect for scoring on valve stems and valve seat sur‐
faces.
– Renew valve if scoring is clearly visible.
5.4 Valve dimensions
Note
Inlet and exhaust valves must not be machined. Only grinding-in

is permitted.
Dimension Inlet valve Exhaust valve

∅a mm 27.5 ± 0.1 25.5 ± 0.1
∅b mm 5.975 ± 0.007 5.965 ± 0.007
c mm 99.3 ± 0.1 99.3 ± 0.1
α ∠° 45° 10' 45° 10'
Volkswagen Technical Site: http://vwts.ru http://vwts.info

17 – Lubrication
1 Sump/oil pump
⇒ “1.1 Exploded view - sump/oil pump”, page 159
⇒ “1.2 Engine oil”, page 163
⇒ “1.3 Removing and installing sump (bottom section)”,
page 163
⇒ “1.4 Removing and installing sump (top section)”, page 165
⇒ “1.5 Removing and installing oil pump”, page 167
⇒ “1.6 Removing and installing oil level and oil temperature send‐
er G266 ”, page 169
1.1 Exploded view - sump/oil pump

♦ Exploded view - sump (bottom section)/oil pump
⇒ page 159
♦ Exploded view - sump (top section) ⇒ page 161
Note
♦ If large quantities of metal shavings or particles are found in

the engine oil when repairing the engine, the oil passages
must be cleaned carefully in order to prevent further damage
occurring later. In addition, renew oil spray jets, engine oil
cooler and oil filter.
♦ Oil spray jet for piston cooling ⇒ page 58 .
Exploded view - sump (bottom section)/oil pump
1. Sump/oil pump 159

1 - Oil level and oil temperature

sender - G266-
⇒ page 169
2 - Seal
3 - Bolt
4 - Sump (bottom section)
⇒ page 163
5 - Bolt
❑ 3 Nm +90°
6 - Baffle plate
7 - Suction pipe
8 - Oil pump
❑ With vacuum pump for
brake servo
❑ Do not dismantle
⇒ page 167
9 - Chain sprocket
❑ For oil pump
10 - Bolt
❑ To loosen, use counter‐
hold tool - T10172 A- to
counterhold chain
sprocket
❑ 30 Nm +45°
11 - Dowel sleeves
❑ 2x
12 - Seal
13 - Bolt
14 - O-ring
15 - Bolt
❑ 3 Nm +90°
16 - Seal
17 - Oil drain plug
❑ 30 Nm
160 Rep. gr.17 - Lubrication

18 - Bolt
❑ 9 Nm
Sump (bottom section) - tightening torque and sequence
Note

angle.

1. -1 … 16- 2 Nm
2. -1 … 16- 3 Nm
3. -1 … 16- Turn 45° further
Oil pump with vacuum pump - tightening torque and sequence
Note

angle.
– Tighten bolts in 3 stages in the sequence shown:

2. -1 … 3- 8 Nm
Exploded view - sump (top section)

1 - Bolt
❑ 9 Nm
2 - Valve for oil pressure con‐
trol - N428-
⇒ page 180
3 - O-ring
❑ Check for damage and
renew if necessary
4 - O-ring
5 - Sump (top section)
⇒ page 165
6 - Dowel sleeve
7 - Guide tube
❑ For oil dipstick
8 - Bolt
❑ Thread-forming
hand so that it is
screwed into old thread.
Then tighten bolt to tor‐
que
❑ 7.5 Nm
9 - O-rings
❑ Check for damage and
renew if necessary
10 - Sealing plug
11 - Bolt
❑ 9 Nm
12 - Seal
13 - Bolt
❑ 9 Nm
14 - Vacuum line
❑ Different versions available; for allocation refer to ⇒ Electronic parts catalogue
❑ Leading from vacuum pump
15 - Bolt
❑ 9 Nm
16 - O-ring
17 - Dowel sleeve
18 - Seal
19 - Plug
❑ For “TDC” marking
❑ 25 Nm

20 - Bolt
Sump (top section) - tightening torque and sequence
Note

angle.

1. -1 … 14- 2 Nm
2. -1 … 14- 5 Nm
3. -1 … 14- Turn 180° further
1.2 Engine oil

♦ Draining and filling up engine oil, checking oil level, removing
and installing oil filter element ⇒ 6-cylinder TDI engine, 3.0 ltr.
4-valve common rail; Rep. gr. 17 ; Sump/oil pump; Engine oil
♦ Oil capacities, oil specifications and viscosity grades ⇒ Main‐
tenance tables .
1.3 Removing and installing sump (bottom

section)
♦ Safety goggles
Removing
Sump/oil pump; Removing and installing sump (bottom section) .
– Drain off engine oil ⇒ page 163 .
– If necessary, remove bolt -1- and press bracket -2- with elec‐
trical wiring harness to one side.

– Unplug electrical connector -arrow- at oil level and oil temper‐

ature sender - G266- (if not already unplugged during prelimi‐
nary work).
Caution
Take care to keep components clean.

♦ There will still be some oil in the sump (bottom section).

– Carefully release sump (bottom section) from bonded joint and
detach.
Installing
Caution
Protect lubrication system and bearings against contamina‐

tion.
WARNING
Risk of eye injury.

– Remove remaining sealant on bottom section -1- and top sec‐

tion of sump with a rotating plastic brush or similar.
Note
– Cut off nozzle of tube at front marking (nozzle ∅ approx. 3

mm).

Caution

– Apply sealant bead -arrow- onto clean sealing surface of sump

(bottom section) as shown in illustration.
• Width of sealant bead: 3.5 mm
Note
Install sump (bottom section) within 5 minutes of applying sealant.
– Carefully fit bottom section of sump onto top section but do not
– First, screw all bolts in by hand and then tighten.
– Top up engine oil and check oil level ⇒ page 163 .
ltr. 4-valve common rail; Rep. gr. 17 ; Sump/oil pump; Removing
and installing sump (bottom section)
Tightening torques
♦ ⇒ Fig. ““Sump (bottom section) - tightening torque and se‐
1.4 Removing and installing sump (top sec‐

tion)
♦ Safety goggles
Removing
• Engine removed and secured to engine and gearbox support
⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr.
10 ; Removing and installing engine; Securing engine to en‐
gine and gearbox support .
• Engine oil drained ⇒ page 163 .
Sump/oil pump; Removing and installing sump (top section) .
– Remove oil pump ⇒ page 167 .
– Remove bracket for alternator ⇒ page 29 .
– Remove bracket for air conditioner compressor ⇒ page 30 .

– Unplug electrical connector -1- for valve for oil pressure control
- N428- .
– Move electrical wiring clear.

– Carefully release sump (top section) from bonded joint, pry
sump off dowel sleeves and detach.
Installing
Note
Renew gaskets, seals and O-rings after removal.
Caution

WARNING
Risk of eye injury.

– Remove sealant residue from sump (top section) -1- and cyl‐
inder block using rotating plastic brush or similar.
Note
– Cut off nozzle of tube at front marking (nozzle ∅ approx. 3

mm).

– Fit seal -1- in sump (top section).
Caution

– Apply beads of sealant -arrows- onto clean sealing surface of

sump (top section) as shown in illustration.
• The grooves on the sealing surfaces must be completely filled
with sealant.
• The beads of sealant must project 3.5 mm above the sealing
surface.
Note
Install sump (top section) within 5 minutes of applying sealant.
– Carefully fit sump (top section) onto cylinder block but do not
– First, screw all bolts in by hand and then tighten.
note the following:
– Install bracket for air conditioner compressor ⇒ page 30 .
– Install bracket for alternator ⇒ page 29 .
– Install oil pump ⇒ page 167 .
– Install timing chain cover (bottom) ⇒ page 73 .
and installing sump (top section)
Tightening torques
♦ ⇒ Fig. ““Sump (top section) - tightening torque and se‐
1.5 Removing and installing oil pump

♦ Counterhold tool - T10172 A- with adapters -T10172/9-

Removing
Sump/oil pump; Removing and installing oil pump .
– Remove sump (bottom section) ⇒ page 163 .
– Unscrew bolt -arrow-; to do so, counterhold chain sprocket for
oil pump using counterhold tool - T10172 A- with adapter -
T10172/9- .
– Press tensioning rail -1- upwards -arrow- and detach chain

sprocket -2-.
– Release tensioning rail.
– Unscrew bolts -arrows- and remove baffle plate -1-.
– Remove bolts -1, 2, 3- and detach oil pump.

Installing
Note
Renew O-rings after removing.
– Check that the two dowel sleeves are fitted in the oil pump.
Install missing dowel sleeves.

– Observe correct installation position of chain sprocket:

• Flat section on chain sprocket must align with flat section on
oil pump -arrow-.
– Tighten bolt -arrow-; to do so, counterhold chain sprocket for

oil pump using counterhold tool - T10172 A- with adapter -
T10172/9- .
– Install sump (bottom section) ⇒ page 163 .
and installing oil pump
Tightening torques
♦ ⇒ “1.1 Exploded view - sump/oil pump”, page 159
1.6 Removing and installing oil level and oil

temperature sender - G266-
Removing
– Drain off engine oil ⇒ page 163 .
– Remove bolts -1- and detach oil level and oil temperature
sender - G266- -item 3-.
Installing
Note
Renew seal -4- after removing.
– Top up engine oil and check oil level ⇒ page 163 .

Tightening torques

2 Engine oil cooler

⇒ “2.1 Exploded view - engine oil cooler”, page 170
⇒ “2.2 Removing and installing engine oil cooler”, page 171
⇒ “2.3 Removing and installing temperature regulator for engine
oil cooler”, page 173
2.1 Exploded view - engine oil cooler

♦ Exploded view - engine oil cooler ⇒ page 170
♦ Exploded view - temperature regulator for engine oil cooler
⇒ page 171
Engine oil cooler
1 - Gasket
❑ For engine oil cooler
2 - Engine oil cooler
catalogue
❑ See note ⇒ page 159
⇒ page 171
3 - Bolt

Engine oil cooler - tightening torque and sequence

– Tighten bolts in stages in the sequence shown (illustration
shows version 1).
1. -1- 2 Nm
2. -2- 9 Nm
3. -1, 3, 4, 5, 6- 9 Nm
Exploded view - temperature regulator for engine oil cooler
1 - Bolt
❑ 9 Nm
2 - Cover
❑ For temperature regula‐
tor for engine oil cooler
3 - O-ring
4 - Temperature regulator for
engine oil cooler
⇒ page 173
2.2 Removing and installing engine oil cool‐

er
2. Engine oil cooler 171

Removing
– Remove coolant pipe (top) ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-
valve common rail; Rep. gr. 19 ; Coolant pipes; Removing and
installing coolant pipes .
– Remove coolant shut-off valve ⇒ page 198 .
Version 1:
– Open hose clip -arrow- and disconnect coolant hose from en‐
gine oil cooler.
– Detach engine oil cooler.
Version 2:
– Open hose clip -arrow- and disconnect coolant hose from en‐
gine oil cooler.
– Detach engine oil cooler.
Installing
Note
♦ Renew gasket after removing.

– Install coolant shut-off valve ⇒ page 198 .

– Install coolant pipe (top) ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-
– Check oil level ⇒ page 163 .
Tightening torques
♦ ⇒ Fig. ““Engine oil cooler - tightening torque and sequence”“ ,
page 171

2.3 Removing and installing temperature

regulator for engine oil cooler
♦ Wrench, 21 mm - T40263-
♦ M8 bolt
Removing
– Remove bolt -arrow- for cover -1-.
2. Engine oil cooler 173

If the temperature regulator for engine oil cooler is covered by the

balance weight -2- of the balance shaft, proceed as follows:
– Bring vibration damper into installation position and secure
with bolt.
Caution

slips.
-arrow-.

crankshaft until temperature regulator for engine oil cooler is
accessible (illustration shows vehicle with alternator).
– To remove cover -2-, screw an M8 bolt -item 1- into thread in

cover and pull out cover by lifting bolt -arrow-.
– Pull out temperature regulator -4- for engine oil cooler.
Installing
Note
Renew O-ring -3- after removal.

Tightening torques
♦ ⇒ “2.1 Exploded view - engine oil cooler”, page 170

3 Crankcase breather
⇒ “3.1 Exploded view - crankcase breather system”, page 175
⇒ “3.2 Removing and installing oil separator”, page 176
3.1 Exploded view - crankcase breather system
1 - Bolt
❑ 10 Nm
❑ Illustration shows alumi‐
nium version
3 - Gasket
4 - Oil separator
⇒ page 176
5 - Bolt
❑ 10 Nm
6 - Hose
❑ To hose connection
7 - O-ring
8 - Gasket
9 - Seals
10 - Bolt
❑ 10 Nm
3. Crankcase breather 175

3.2 Removing and installing oil separator

Removing
– Remove cylinder head cover (right-side) ⇒ page 121 .
– Remove bolts -arrows- and detach oil separator -2- from cyl‐
inder head cover -1-.
Installing
Note
Renew gaskets/seals after removing.
– Install cylinder head cover (right-side) ⇒ page 121 .

Tightening torques
♦ ⇒ “3.1 Exploded view - crankcase breather system”,
page 175

4 Oil filter/oil pressure switches

⇒ “4.1 Exploded view - oil filter”, page 177
⇒ “4.2 Removing and installing oil filter housing”, page 178
⇒ “4.3 Removing and installing oil pressure sender G10 ”,
page 179
⇒ “4.4 Checking oil pressure”, page 180
⇒ “4.5 Removing and installing valve for oil pressure control N428
”, page 180
⇒ “4.6 Removing and installing oil temperature sender 2 G664 ”,
page 181
4.1 Exploded view - oil filter
1 - Bolt
2 - Oil filter housing
able ⇒ Electronic parts
catalogue
⇒ page 178
3 - Seal
❑ Permanently attached
to oil pressure sender;
not available as a re‐
placement part
4 - Oil pressure sender - G10-
❑ Checking ⇒ Vehicle di‐
agnostic tester
⇒ page 179
❑ 3 Nm +90°
5 - Oil filter element
⇒ page 163
6 - O-ring
7 - Sealing cap
❑ With oil filter bypass
valve
❑ 25 Nm
8 - Bolt
❑ 9 Nm
9 - Sealing plug or connection
❑ Vehicles without electric compressor: sealing plug
❑ Vehicles with electric compressor: connection ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep.
gr. 19 ; Coolant pipes; Exploded view - coolant pipes
4. Oil filter/oil pressure switches 177

10 - O-rings
11 - Gasket
12 - O-ring
Oil filter housing - tightening torque and sequence

– Tighten bolts in the sequence -1 ... 6- to 9 Nm.
4.2 Removing and installing oil filter housing

Removing
cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 17 ; Oil
filter/oil pressure switches; Removing and installing oil filter hous‐
ing .


– Press lines slightly towards front and detach oil filter housing.
Installing
Note
♦ Renew gasket and O-ring after removal.

– Install coolant pipe (front) ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-

– Install oil filter element ⇒ page 163 .
Note
Do not reuse coolant.

ltr. 4-valve common rail; Rep. gr. 17 ; Oil filter/oil pressure
switches; Removing and installing oil filter housing
Tightening torques
♦ ⇒ Fig. ““Oil filter housing - tightening torque and sequence”“ ,
page 178
4.3 Removing and installing oil pressure

sender - G10-
♦ Socket (24 mm) - T40363- (not illustrated)
Procedure
filter/oil pressure switches ; Removing and installing oil pressure
sender - G10- .


– Place a cloth underneath to catch escaping engine oil.
– Remove oil pressure sender - G10- -item 2-.
– Renew seal after removing.
– Insert new oil pressure sender - G10- into cylinder head im‐
mediately to avoid loss of engine oil.
switches ; Removing and installing oil pressure sender - G10-
Tightening torques
♦ ⇒ “4.1 Exploded view - oil filter”, page 177
4.4 Checking oil pressure

When checking oil pressure, refer to ⇒ Vehicle diagnostic tester.
– Connect vehicle diagnostic tester .
– Select and start Diagnosis .
– Choose Select own test and select following options one
after the other:
♦ Drive train (display depends on model)
♦ Select engine code and engine (display depends on
model)
♦ 0001 - Self-diagnosis compatible systems or Systems
with diagnostic capability
♦ 0001 - Engine electronics

♦ 0001 - Subsystems, background conditions
♦ Oil pressure check
– Start selected program and follow instructions shown on dis‐
play of vehicle diagnostic tester.
4.5 Removing and installing valve for oil

pressure control - N428-
Procedure
filter/oil pressure switches; Removing and installing valve for oil
pressure control - N428- .


– Place a cloth underneath to catch escaping engine oil.
– Unscrew bolt -2- and remove valve for oil pressure control -
N428- . (Illustration shows vehicle with alternator.)
– Renew O-ring after removal.
– To avoid loss of engine oil, insert new valve for oil pressure
control - N428- immediately.
switches; Removing and installing valve for oil pressure control -
N428-
Tightening torques
4.6 Removing and installing oil temperature

sender 2 - G664-
⇒ “4.6.1 Removing and installing oil temperature sender 2 G664
- vehicles with alternator”, page 181
- vehicles with starter-alternator”, page 182
- vehicles with electric compressor”, page 183
4.6.1 Removing and installing oil temperature

sender 2 - G664- - vehicles with alter‐
nator
Procedure
– Remove noise insulation (front) ⇒ General body repairs, ex‐
terior; Rep. gr. 66 ; Noise insulation; Removing and installing
noise insulation .

Caution
Oil will escape through mounting hole for oil temperature send‐
er.
♦ Lay a cloth under the mounting hole to catch escaping
engine oil or close the mounting hole using a clean plug
from the engine bung set - VAS 6122- .
– Unscrew bolt -1- and remove oil temperature sender 2 -

G664- .
Note
Renew O-ring after removal.
Tightening torques
♦ ⇒ “1.2 Exploded view - sealing flange (pulley end)”, page 21

sender 2 - G664- - vehicles with starter-
alternator
Removing
filter/oil pressure switches ; Removing and installing oil tempera‐
ture sender 2 - G664- .

Caution
Oil will escape through mounting hole for oil temperature send‐
er.
♦ Lay a cloth under the mounting hole to catch escaping
engine oil or close the mounting hole using a clean plug
from the engine bung set - VAS 6122- .
– Unscrew bolt -1- and remove oil temperature sender 2 -

G664- .
Installing
Note

switches ; Removing and installing oil temperature sender 2 -
G664-
Tightening torques
♦ ⇒ “1.9 Removing and installing sealing flange (pulley end)”,
page 33

sender 2 - G664- - vehicles with electric
compressor
4-valve common rail; Rep. gr. 17 ; Oil filter/oil pressure switches;
Removing and installing oil temperature sender 2 - G664- .

19 – Cooling
1 Cooling system/coolant
⇒ “1.1 Connection diagram - coolant hoses”, page 184
⇒ “1.2 Checking cooling system for leaks”, page 184
⇒ “1.3 Draining and filling cooling system”, page 187
1.1 Connection diagram - coolant hoses

All components are described in ⇒ 6-cylinder TDI engine, 3.0 ltr.
4-valve common rail); Rep. gr. 19 ; Cooling system/coolant; Con‐
nection diagram - coolant hoses .
1.2 Checking cooling system for leaks

♦ Cooling system tester - V.A.G 1274 B-
♦ Adapter for cooling system tester - V.A.G 1274/8-
♦ Cooling system tester adapter - V.A.G 1274B/15- for filler cap

(version 1)
184 Rep. gr.19 - Cooling

♦ Cooling system tester adapter - V.A.G 1274/9- for filler cap

(version 2)
♦ Safety goggles
♦ Protective gloves
Procedure
• Engine must be warm.
Cooling system/coolant; Checking cooling system for leaks .
WARNING
Risk of scalding as hot coolant can escape.

– Release fastener -arrow- (if necessary) and open filler cap

-1- on coolant expansion tank.
1. Cooling system/coolant 185

– Fit cooling system tester - V.A.G 1274 B- with adapter -

V.A.G 1274/8- onto coolant expansion tank.
– Using hand pump on cooling system tester, build up a pres‐
sure of approx. 1.0 bar.
• The pressure should not drop more than 0.2 bar within 10 mi‐
nutes.
– If the pressure drops more than 0.2 bar, locate leak and elim‐
inate fault.
Note
The drop in pressure of 0.2 bar within 10 minutes is caused by

the decrease in coolant temperature. The colder the engine is,
the less the pressure will fall. If necessary, check again when the
engine is cold.
Checking pressure relief valve in filler cap
Filler cap (version 1):

V.A.G 1274 B/15- onto filler cap.
– Using hand pump on cooling system tester, build up a pres‐
sure of approx. 2 bar.
Blue filler cap
• The pressure must be reduced to 1.6 ... 1.4 bar and kept at
this level.
– Renew filler cap if pressure relief valve does not react as de‐
scribed.
Black filler cap
• The pressure must be reduced to 1.8 ... 1.6 bar and kept at
this level.
scribed.

Filler cap (version 2):

V.A.G 1274/9- onto filler cap.
– Build up pressure with hand pump on cooling system tester.
Blue filler cap
• The pressure relief valve should open at a pressure of
1.4 ... 1.6 bar.
scribed.
Black filler cap:
• The pressure relief valve should open at a pressure of
1.6 ... 1.8 bar.
scribed.
1.3 Draining and filling cooling system

Coolant specifications
Caution
To ensure optimal corrosion protection, only distilled water

may be mixed with coolant additives.
1. Cooling system/coolant 187

Note
♦ The effectiveness of the coolant is greatly influenced by the

quality of the water with which it is mixed. Because water may
contain different substances depending on the country or even
the region, the water quality to be used for cooling systems
has been specified. Distilled water meets all the requirements
and is therefore recommended for use when topping up or fill‐
ing up with coolant.
♦ Use only coolant additives listed in the ⇒ Electronic parts
catalogue (ETKA) . If you use other coolant additives, this can
significantly impair in particular the corrosion protection effect.
The resulting damage could lead to loss of coolant and con‐
sequently to serious damage to the power unit.
♦ Coolant with the recommended mixture ratio prevents frost
and corrosion damage and stops scaling. At the same time it
raises the boiling point of the fluid in the system. For this rea‐
son the cooling system must be filled all year round with the
correct coolant additive.
♦ Because of its high boiling point, the coolant improves power
unit reliability under heavy loads, particularly in countries with
tropical climates.
♦ The refractometer - T10007A- MUST be used to determine the
current level of frost protection.
♦ The mixture must guarantee frost protection down to at least
-25 ℃ (in countries with arctic climate: down to -36 ℃). The
amount of antifreeze should only be increased if greater frost
protection is required in very cold climates. This must only be
down to -48 ℃, however, as otherwise the cooling efficiency
of the coolant is impaired.
♦ The coolant concentration must not be reduced by adding wa‐
ter even in warmer seasons and in warmer countries. Frost
protection must be provided to at least -25 ℃.
♦ Read off the level of frost protection on the scale for the rele‐
vant coolant additive.
♦ The temperature indicated on the refractometer - T10007A-
corresponds to the temperature at which the first ice crystals
can form in the coolant.
♦ Do not reuse coolant.
♦ Only use water/coolant additive as a lubricant for coolant ho‐
ses.
Draining and filling cooling system

4-valve common rail; Rep. gr. 19 ; Cooling system/coolant; Drain‐
ing and filling cooling system .

2 Coolant pump/thermostat assembly

⇒ “2.1 Exploded view - coolant pump”, page 189
⇒ “2.2 Exploded view - electric coolant pump”, page 190
⇒ “2.3 Exploded view - thermostat”, page 190
⇒ “2.4 Exploded view - coolant temperature senders”,
page 193
⇒ “2.5 Removing and installing electric coolant pump”,
page 193
⇒ “2.6 Removing and installing coolant pump”, page 193
⇒ “2.7 Removing and installing thermostat”, page 196
⇒ “2.8 Removing and installing thermostat housing”, page 196
⇒ “2.9 Removing and installing coolant temperature sender G62
”, page 196
⇒ “2.10 Removing and installing temperature sender for engine
temperature regulation G694 ”, page 197
⇒ “2.11 Removing and installing coolant valves”, page 198
2.1 Exploded view - coolant pump
1 - Bolt
❑ Aluminium or steel
bolts, depending on ver‐
sion
❑ Renew aluminium bolts
after removing
2 - Bolt
❑ 23 Nm
3 - Poly V-belt pulley for cool‐
ant pump
marking “vorne” (front)
faces in direction of trav‐
el
4 - Coolant pump
❑ It is only permissible to
re-install the coolant
pump if the gasket is still
secured to the housing
in all areas; check this
with your hand
2. Coolant pump/thermostat assembly 189

⇒ page 193
Coolant pump - tightening torque and sequence

A - Steel bolts:
– Tighten steel bolts in the sequence shown:
1. -1 … 17- 9 Nm
B - Aluminium bolts:
Note

angle.
– Tighten aluminium bolts in stages in the sequence shown:

1. -1 … 17- 3 Nm
2. -1 … 17- Turn 90° further
2.2 Exploded view - electric coolant pump

4-valve common rail; Rep. gr. 19 ; Coolant pump/thermostat as‐
sembly; Exploded view - electric coolant pump .
2.3 Exploded view - thermostat

♦ Exploded view - thermostat ⇒ page 190
♦ Exploded view - coolant shut-off valve ⇒ page 192
Exploded view - thermostat

1 - Bolt
❑ Tightening torque ⇒ 6-
cylinder TDI engine, 3.0
ltr. 4-valve common rail;
Rep. gr. 19 ; Coolant
pipes; Exploded view -
coolant pipes
2 - Coolant pipe (front)
❑ Exploded view ⇒ 6-cyl‐
inder TDI engine, 3.0 ltr.
4-valve common rail;
coolant pipes
3 - O-ring
4 - O-ring
5 - Thermostat
⇒ page 196
6 - Bolt
❑ Thread-forming
hand so that it is
que
❑ 5.5 Nm
7 - Gasket
8 - Gasket
9 - Bolt
❑ 9 Nm
10 - O-ring
11 - Bolt
❑ Tightening torque ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes;
Exploded view - coolant pipes
12 - Coolant pipe (top right)
❑ Exploded view ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes; Ex‐
ploded view - coolant pipes
13 - Thermostat housing
14 - O-ring
15 - Compression spring
❑ Removing and installing ⇒ “2.7 Removing and installing thermostat”, page 196

16 - Valve
❑ For coolant flap
❑ Removing and installing ⇒ “2.7 Removing and installing thermostat”, page 196
Exploded view - coolant shut-off valve
1 - Seal
2 - Bolt
❑ 9 Nm
3 - Coolant connection
4 - Coolant hose
5 - Bolt
❑ 9 Nm
6 - Coolant shut-off valve
⇒ page 198
7 - Gasket

2.4 Exploded view - coolant temperature senders
1 - Bolt
❑ 9 Nm
2 - Coolant temperature send‐
er - G62-
⇒ page 196
3 - O-rings
4 - O-rings
5 - Temperature sender for en‐
gine temperature regulation -
G694-
⇒ page 197
6 - Bolt
❑ 9 Nm
2.5 Removing and installing electric coolant

pump
sembly; Removing and installing electric coolant pump .
2.6 Removing and installing coolant pump


♦ Pin wrench - 3212-
♦ Coolant collecting system - VAS 5014- or drip tray for work‐

shop hoist - VAS 6208-
♦ Angled screwdriver - VAS 6416-
Removing
Coolant pump/thermostat assembly; Removing and installing
coolant pump .


cooling system .
– Remove poly V-belt from coolant pump pulley ⇒ page 22 .
– Remove bolts for coolant pump pulley -arrows- (counterhold
with pin wrench - 3212- ).
– Place collector tank from coolant collecting system -VAS

5014- or drip tray for workshop hoist - VAS 6208- underneath.
– Remove bolts and detach coolant pump.
– If necessary, remove spreader rivets -arrow- using angle driv‐

er for cross-head screws - VAS 6416- , detach noise insulation
and press it to one side.
Installing
Note

angle.
♦ Do not reuse coolant.
– Clean sealing surface.

– Install poly V-belt ⇒ page 22 .
ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pump/thermostat
assembly; Removing and installing coolant pump .
Tightening torques
♦ ⇒ Fig. ““Coolant pump - tightening torque and sequence”“ ,
page 190

2.7 Removing and installing thermostat

Removing
– Remove oil filter housing ⇒ page 178 .
– Remove coolant pump ⇒ page 193 .
– Unscrew bolts -arrows- and detach thermostat -1-.
Installing
Note
Renew gasket and O-ring after removal.
– Install coolant pump ⇒ page 193 .

– Install oil filter housing ⇒ page 178 .
Tightening torques
2.8 Removing and installing thermostat

housing
Removing
– Remove engine oil cooler ⇒ page 171 .
– Remove oil filter housing ⇒ page 178 .
– Unscrew bolts -arrows-, pull thermostat housing towards rear
and remove.
Installing
Note
♦ Renew gasket and O-rings after removal.

– Install oil filter housing ⇒ page 178 .

– Install engine oil cooler ⇒ page 171 .
Tightening torques
♦ ⇒ “2.3 Exploded view - thermostat”, page 190
♦ ⇒ Fig. ““Engine oil cooler - tightening torque and sequence”“ ,
page 171
2.9 Removing and installing coolant temper‐

ature sender - G62-
Procedure
• Engine cold.
– Preparatory work may be necessary depending on model ⇒
6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr.

19 ; Coolant pump/thermostat assembly; Removing and in‐

stalling coolant temperature sender - G62- .
– Remove intake manifold flap motor - V157- ⇒ page 234 .

– Unscrew bolt -2- and pull off coolant temperature sender -
G62- .
– Renew O-rings after removing.
– To avoid loss of coolant, insert new coolant temperature send‐
er - G62- immediately.
note the following:
– Install intake manifold flap motor - V157- ⇒ page 234 .
– Check coolant level ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve
– Additional work depending on model ⇒ 6-cylinder TDI engine,
3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pump/ther‐
mostat assembly; Removing and installing coolant tempera‐
ture sender - G62- .
Tightening torques
♦ ⇒ “5.1 Exploded view - exhaust gas recirculation system”,
page 312
2.10 Removing and installing temperature

sender for engine temperature regula‐
tion - G694-
⇒ “2.10.1 Removing and installing temperature sender for engine
temperature regulation G694 - vehicles without electric compres‐
sor”, page 197
⇒ “2.10.2 Removing and installing temperature sender for engine
temperature regulation G694 - vehicles with electric compressor”,
page 198
2.10.1 Removing and installing temperature

tion - G694- - vehicles without electric
compressor
Procedure
Coolant pump/thermostat assembly; Removing and installing
temperature sender for engine temperature regulation - G694- .

• Engine cold.

– Place a cloth underneath to catch escaping coolant.
– Unscrew bolt -2- and detach temperature sender for engine
temperature regulation - G694- .
– Renew O-rings after removing.
– To avoid loss of coolant, insert new temperature sender for
engine temperature regulation - G694- immediately.
note the following:
– Check coolant level ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve
Tightening torques
♦ ⇒ “2.4 Exploded view - coolant temperature senders”,
page 193
2.10.2 Removing and installing temperature

tion - G694- - vehicles with electric com‐
pressor
sembly; Removing and installing temperature sender for engine
temperature regulation - G694- .
2.11 Removing and installing coolant valves

⇒ “2.11.1 Removing and installing coolant shut-off valve”,
page 198
⇒ “2.11.2 Removing and installing electric coolant valves”,
page 199
2.11.1 Removing and installing coolant shut-off

valve

Removing
– Remove exhaust gas recirculation cooler (front)
⇒ page 314 .
– Disconnect vacuum hose -2-.
– Unscrew bolts -arrows- and detach shut-off valve -3-.
– Release hose clip -1- and detach coolant hose.
Installing
Note
♦ Renew gasket after removing.

– Install exhaust gas recirculation cooler ⇒ page 314 .

Tightening torques
♦ ⇒ “2.3 Exploded view - thermostat”, page 190
2.11.2 Removing and installing electric coolant

valves
sembly; Removing and installing coolant valves .

3 Coolant pipes
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes .

4 Radiator/radiator fans
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Radiator/radi‐
ator fans .
4. Radiator/radiator fans 201

21 – Turbocharging/supercharging
1 Turbocharger
⇒ “1.1 Exploded view - turbocharger”, page 202
⇒ “1.2 Removing and installing turbocharger”, page 206
1.1 Exploded view - turbocharger

♦ Exploded view - turbocharger, part I ⇒ page 202
♦ Exploded view - turbocharger, part II ⇒ page 203
Exploded view - turbocharger, part I
1 - Gasket
3 - Bolt
❑ 23 Nm
4 - Studs
catalogue
❑ Must always be re‐
newed if nuts are loos‐
ened
5 - Gasket
6 - Bolt
❑ 5 Nm +90°
7 - Pipe
❑ For exhaust gas recircu‐
lation
8 - Gasket
9 - Turbocharger
⇒ page 206
❑ Performing adaptions
required after renewing
a component (using
⇒ Vehicle diagnostic tester) ⇒ “3.8 Performing adaptions after renewing a component”, page 10
10 - Nut
❑ Coat thread with high-temperature paste ⇒ Electronic parts catalogue
202 Rep. gr.21 - Turbocharging/supercharging

11 - Seal
12 - Seal
13 - Screw-type clip
14 - Emission control module
❑ Exploded view ⇒ page 292
15 - Screw-type clip
❑ 8 Nm
16 - Exhaust manifold
17 - Bolt
18 - Bracket
❑ For turbocharger
19 - Bolt
20 - Bracket
❑ For turbocharger
21 - Bolt
Exploded view - turbocharger, part II
1. Turbocharger 203
1 - Air pipe
2 - Bolt
sequence ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-
valve common rail; Rep.
gr. 21 ; Charge air sys‐
tem; Exploded view -
charge air system
3 - Seal
❑ Renew if damaged
4 - Bolt
❑ 9 Nm
5 - Resonator
6 - O-ring
7 - Bolt
Rep. gr. 26 ; Exhaust
gas recirculation sys‐
tem; Exploded view - ex‐
haust gas recirculation
system
8 - Hose
9 - Bracket
❑ For vehicles with elec‐
tric compressor
10 - Bolt
tric compressor
Aluminium cylinder head cover
❑ 4 Nm
Plastic cylinder head cover
❑ Thread-forming
❑ 3.5 Nm
11 - Sender 1 for turbocharger speed - G688-
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 21 ; Turbocharger;
Removing and installing sender 1 for turbocharger speed - G688-
12 - Bolt
❑ 5 Nm
13 - Bolt
❑ 5.5 Nm
14 - Vacuum hose

15 - Seal
16 - Pipe
❑ For exhaust gas recirculation
17 - Ball stud
❑ For engine cover panel
❑ 5 Nm
18 - Exhaust gas temperature sender 1 - G235-
19 - Seal
20 - Turbocharger
❑ Performing adaptions required after renewing a component (using ⇒ Vehicle diagnostic tester)
⇒ “3.8 Performing adaptions after renewing a component”, page 10
21 - Securing clips
❑ For operating rod
22 - Operating rod
23 - Bolt
❑ 9 Nm
24 - Bracket
25 - Bolt
❑ 9 Nm
26 - Control unit for turbocharger 1 - J724-
❑ Not supplied separately
Turbocharger - tightening torque and sequence
Note
Renew studs and nuts after removing.
– Tighten bolts and nuts in stages in the sequence shown:

Stage Bolts/nuts Torque for tightening/tightening fur‐
ther
1. Studs for nuts 14 Nm
-2, 3-
2. -2, 3- Screw in by hand until contact is made
3. -2, 3- 12 Nm
4. -2, 3- 50 Nm
5. -2, 3- Turn 90° further
6. -4, 5- Screw in by hand until contact is made
7. -4- 9 Nm
8. -5- 9 Nm
1. Turbocharger 205
Bracket -1- for turbocharger - tightening torque

1. -arrows- Screw in by hand until contact is made
2. -arrows- 15 Nm
3. -arrows- 28 Nm
25 Nm when using insert tool XZN 10
-V.A.G 1331/15-
1.2 Removing and installing turbocharger
Caution
If the turbocharger has suffered mechanical damage (e.g.

damaged compressor wheel), it is not sufficient merely to fit a
new turbocharger. The following work must be performed in
order to avoid further damage:
♦ Check air cleaner housing, air filter element and air hoses
for dirt and foreign particles.
♦ Check the entire charge air system (including the charge
air cooler) for foreign matter.
♦ If foreign matter is found in the charge air system, clean
all relevant ducts and hoses and renew charge air cooler
if necessary.
Risk of malfunctions caused by dirt.
♦ Observe rules for cleanliness ⇒ page 7 .
Note:
Mechanical faults on the turbocharger can be caused by foreign
matter from the exhaust manifold.
♦ Engine bung set - VAS 6122-
Removing
Turbocharger; Removing and installing turbocharger .

Vehicles without electric compressor:

– Remove coolant pipe (rear) for turbocharger ⇒ 6-cylinder TDI
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant
pipes; Removing and installing coolant pipes .
– Remove coolant pipe (top front) for turbocharger ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 19 ; Coolant
Vehicles with electric compressor:
– Remove coolant pipe “1” for turbocharger ⇒ 6-cylinder TDI
– Remove coolant pipe “3” for turbocharger ⇒ 6-cylinder TDI
Exhaust gas recirculation pipe - version 1:
– Release hose clip -1- and detach exhaust gas recirculation
pipe -2-.

– Release screw-type clips -1- and detach exhaust gas recircu‐
lation pipe -2-.

– Release hose clips -1- and disconnect exhaust gas recircula‐
tion hose.
– Detach exhaust gas recirculation pipe -2-.
1. Turbocharger 207
All versions (continued):

– If still fitted, disconnect crankcase breather hose -2- from res‐
onator -1- (press release tabs on both sides to do so).
– Remove bolts -1- and pull air pipe -2- off turbocharger (leave
in installation position). (Different versions depending on mod‐
el.)
– Unscrew exhaust gas temperature sender 1 - G235- .
– If necessary, release catch -arrow B-, detach exhaust gas re‐

circulation cooler changeover valve - N345- -item 1- from
bracket -2- -arrow A- and press to one side.

– Release clips -1, 2- and slide them onto exhaust manifold/tur‐

bocharger.
– Remove bolts -arrows- and move automatic glow period con‐

trol unit - J179- to one side together with bracket.
– Remove bolts -arrows- for exhaust gas recirculation pipe.
1. Turbocharger 209
– Unplug electrical connector -1- for turbocharger 1 control unit

- J724- .
– Slacken bolts -5- and remove bolts -4-.
– Press operating rod for turbocharger 1 control unit - J724- up‐
wards and remove nuts -2, 3-.
– Remove turbocharger.
Installing
Note
♦ Renew seals, nuts and O-ring after removal.

♦ Fill turbocharger with engine oil at connection for oil supply
line.
♦ After installing the turbocharger, allow the engine to idle for
approx. 1 minute without pressing the accelerator to ensure
that the turbocharger is supplied with oil.
– Install coolant pipes ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve

common rail; Rep. gr. 19 ; Coolant pipes; Removing and in‐
stalling coolant pipes .
ltr. 4-valve common rail; Rep. gr. 21 ; Turbocharger; Removing
and installing turbocharger .
Perform adaptions required after renewing a component (using
⇒ Vehicle diagnostic tester)
page 10 .
Tightening torques
page 312

2 Charge air system

⇒ “2.1 Exploded view - charge air system”, page 211
⇒ “2.2 Exploded view - hose connections for charge air system”,
page 211
⇒ “2.3 Removing and installing charge air cooler”, page 212
⇒ “2.4 Removing and installing charge pressure sender G31 ”,
page 212
⇒ “2.5 Removing and installing charge air temperature sender”,
page 213
⇒ “2.6 Checking charge air system for leaks”, page 213
2.1 Exploded view - charge air system

4-valve common rail; Rep. gr. 21 ; Charge air system; Exploded
view - charge air system .
2.2 Exploded view - hose connections for

charge air system
Note
♦ Hose connections and air pipes/hoses must be free of oil and

grease prior to fitting.
♦ If using used hose clips to secure the air hoses at their con‐
nections, spray rust remover onto the worm threads before
installing.
Hose clips on pressure side are fitted with retaining hooks

-arrows-.
• To disconnect air hose, hose clip must be loosened far
enough.
• Hose clips which have been loosened can be re-used.
• Hose clip -1- with retaining hooks -arrows- must not be pulled
off air hose.
• If a hose clip with retaining hooks is pulled off air hose, air hose
must be renewed.
• New air hoses are supplied with hose clip fitted.
2. Charge air system 211

Tightening torque for

1- Hose clip with width -a- = 12 mm: 5.5 Nm
2- Hose clip with width -b- = 9 mm: 3.4 Nm
2.3 Removing and installing charge air cool‐

er
4-valve common rail; Rep. gr. 21 ; Charge air system; Removing
and installing charge air cooler .
2.4 Removing and installing charge pres‐

sure sender - G31-
⇒ “2.4.1 Removing and installing charge pressure sender G31 -
vehicles without electric compressor”, page 212
⇒ “2.4.2 Removing and installing charge pressure sender G31 -
vehicles with electric compressor”, page 212
2.4.1 Removing and installing charge pres‐

sure sender - G31- - vehicles without
electric compressor
Removing
– Remove engine cover panel ⇒ page 14 .
– Unscrew bolt -1- and remove charge pressure sender - G31- .
Installing
– Install engine cover panel ⇒ page 14 .
Tightening torques
2.4.2 Removing and installing charge pres‐

sure sender - G31- - vehicles with elec‐
tric compressor
and installing charge pressure sender - G31- .

2.5 Removing and installing charge air tem‐

perature sender
and installing charge air temperature sender .
2.6 Checking charge air system for leaks

♦ Vehicle diagnostic tester
♦ Charge air system tester - V.A.G 1687-
♦ Adapters - V.A.G 1687/3- , -V.A.G 1687/10- , -V.A.G 1687/15- ,

-V.A.G 1687/18-2-
♦ Ultrasonic tester - V.A.G 1842-

♦ Leak detection spray (commercially available)
Procedure
– Observe rules for cleanliness ⇒ page 7 .
Charge air system; Checking charge air system for leaks .
– Loosen bolted connections -arrows- and push clamp towards
rear.
– Lower front exhaust pipe/trap catalytic converter slightly and
detach clamp.
– Tie up front exhaust pipe/trap catalytic converter.

Version 1:
– Seal off front exhaust pipe/trap catalytic converter with adapt‐
ers -V.A.G 1687/3- and -V.A.G 1687/15- .
Version 2:
– Seal off trap catalytic converter with adapter -V.A.G
1687/18-2- .
Continued:
– Connect adapter -V.A.G 1687/10- to turbocharger.
– Connect hose -1- of charge air system tester -V.A.G 1687- to
adapter.

Prepare charge air system tester - V.A.G 1687- as follows:

– Unscrew pressure control valve -2- completely and close
valves -3- and -4-.
• Make sure knob is pulled out before turning pressure control
valve -2-.
– Using a commercially available connection piece, connect
charge air system tester - V.A.G 1687- to compressed air -1-.
Note
If there is water in sight glass, remove drain plug -6- and drain
water.
– Open valve -3-.
Caution
Risk of damage if pressure is set too high.

♦ The pressure must not exceed 0.2 bar.
– Adjust pressure to 0.2 bar via pressure control valve -2-.

– Open valve -4- and wait until test system is pressurised. If
necessary, adjust pressure to 0.2 bar again.
– Switch on ignition.
after the other:
model)

♦ 0001 - Subsystems, background conditions
♦ 0001 - Check charge air system for leaks
♦ Carry out test
– Check charge air system for audible leaks or leaks that can be
felt with the hand; apply commercially available leak detection
spray or use ultrasonic tester - V.A.G 1842- .

Note
♦ A small amount of air escapes through the valves and enters

the engine. Therefore it is not possible to perform a pressure
retention test.
♦ For operation of ultrasonic tester -V.A.G 1842- , refer to ⇒
Operating instructions .
♦ Release pressure in test circuit by detaching hose coupling
from adapter before removing adapter.
Assembling
Note
♦ Renew seal and O-rings after removal.


ltr. 4-valve common rail; Rep. gr. 21 ; Charge air system; Check‐
ing charge air system for leaks .
Tightening torques
♦ ⇒ “2.2 Exploded view - hose connections for charge air sys‐
tem”, page 211
26 ; Exhaust pipes/silencers; Exploded view - silencers

23 – Mixture preparation - injection

1 Injection system
⇒ “1.1 Overview - fuel system”, page 217
⇒ “1.2 Overview of fitting locations - injection system”,
page 217
⇒ “1.3 Filling and bleeding fuel system”, page 217
⇒ “1.4 Checking fuel system for leaks”, page 218
1.1 Overview - fuel system

4-valve common rail; Rep. gr. 23 ; Injection system; Overview -
fuel system .
1.2 Overview of fitting locations - injection

system
4-valve common rail; Rep. gr. 23 ; Injection system; Overview of
fitting locations - injection system .
1.3 Filling and bleeding fuel system

If components of the fuel system between the fuel tank and the
high-pressure pump are removed or renewed, the fuel system
must be bled.
Caution
Running when dry causes irreparable damage to fuel pump.

• Never allow fuel pump to run while it is empty.
Proceed as follows to fill high-pressure pump with fuel.

• Check fuel gauge in instrument cluster; fuel gauge needle
must indicate that fuel is above reserve level.
– Switch on ignition.
after the other:
model)

♦ 0001 - Activate fuel pump
1. Injection system 217

♦ Carry out test

♦ Select 120 seconds.
– The fuel pump must run for 120 seconds to ensure that the
fuel system is filled sufficiently with fuel.
– Start engine after filling fuel system.
– Run engine at moderate speed for several minutes and then
switch off.
– Check fuel system for leaks.
– Erase entry in event memory.
– Road-test vehicle and accelerate with full throttle at least once.
– Then check high-pressure system again for leaks.
1.4 Checking fuel system for leaks

Procedure
– Allow engine to run for several minutes at moderate rpm.
– Switch off ignition.
– Check complete fuel system for leaks.
– If leaks are found although the connections have been tight‐
ened to the correct torque, the relevant component must be
renewed.
– Road-test vehicle and accelerate with full throttle at least once.
– Finally, check high-pressure system again for leaks.
218 Rep. gr.23 - Mixture preparation - injection

2 Vacuum system
⇒ “2.1 Connection diagram - vacuum system”, page 219
⇒ “2.2 Checking vacuum system”, page 219
2.1 Connection diagram - vacuum system
Note
Vacuum hoses in vehicle are not coloured.
1 - Exhaust gas recirculation

cooler change-over valve -
N345-
2 - Vacuum hose
❑ From exhaust gas recir‐
culation cooler change-
over valve - N345- to
vacuum unit at exhaust
gas recirculation cooler
3 - Vacuum unit
❑ At exhaust gas recircu‐
lation cooler
4 - Vacuum unit
❑ At coolant shut-off valve
5 - Vacuum line
❑ From coolant valve for
cylinder head - N489- to
vacuum unit at coolant
shut-off valve
6 - Coolant valve for cylinder
head - N489-
7 - Vacuum supply hose
❑ With non-return valve
❑ Leading from vacuum
pump to brake servo
catalogue
8 - Vacuum supply hose
❑ With non-return valve
❑ To coolant valve for cyl‐
inder head - N489- and
exhaust gas recirculation cooler change-over valve - N345-
2.2 Checking vacuum system

2. Vacuum system 219

♦ Hand vacuum pump - VAS 6213-
Procedure
– Check all vacuum lines in the complete vacuum system for:
♦ Cracks
♦ Traces of animal bites
♦ Kinked or crushed lines
♦ Porous or leaking lines
– Check vacuum line to solenoid valve and from solenoid valve
to corresponding component.
– If a fault is stored in the event memory, check the vacuum lines
leading to the relevant component and also check the remain‐
ing vacuum lines in the system.
– If it is not possible to build up a vacuum with the hand vacuum
pump - VAS 6213- or if the vacuum pressure drops again im‐
mediately, check the hand vacuum pump and connecting
hoses for leaks.

3 Air cleaner
engine, 3.0 ltr. 4-valve common rail; Rep. gr. 23 ; Air cleaner .
3. Air cleaner 221

4 Intake manifold
⇒ “4.1 Exploded view - intake manifold”, page 222
⇒ “4.2 Removing and installing intake manifold (top section)”,
page 228
⇒ “4.3 Removing and installing intake manifold (bottom section)”,
page 232
⇒ “4.4 Removing and installing intake manifold flap motor V157
”, page 234
⇒ “4.5 Removing and installing throttle valve module J338 ”, page
236
4.1 Exploded view - intake manifold

⇒ “4.1.1 Exploded view - intake manifold, vehicles without electric
compressor”, page 222
⇒ “4.1.2 Exploded view - intake manifold, vehicles with electric
compressor”, page 225
4.1.1 Exploded view - intake manifold, vehicles without electric compressor
1 - Bolt
❑ 9 Nm
2 - Pipe
lation
3 - Seal
4 - Bolt
❑ 9 Nm
5 - Bolt
❑ 9 Nm
6 - Bracket
❑ For air pipe and exhaust
change-over valve -
N345-
7 - Intake manifold flap motor -
V157-
stalling intake manifold
flap motor V157 ”,
page 234
8 - Gasket
9 - Intake manifold (top sec‐
tion)
(top section)”,
page 228

10 - High-pressure pipe
❑ With retaining clamp
11 - Bolt
❑ Thread-forming
❑ 7.5 Nm
12 - Retainer
❑ For electrical wiring harness
13 - Bolt
❑ Thread-forming
❑ 7.5 Nm
14 - Ball stud
❑ Thread-forming
❑ 4 Nm
15 - Bolt
❑ Thread-forming
❑ 7.5 Nm
16 - Retainer
❑ For coolant hoses
17 - Bolt
18 - Seal
❑ 16x
❑ Available in different sizes
19 - Bolt
❑ 9 Nm
20 - Seal
❑ 16x
21 - Intake manifold (bottom section)
❑ Removing and installing ⇒ “4.3 Removing and installing intake manifold (bottom section)”, page 232
22 - Bolt
❑ Thread-forming
❑ 7.5 Nm
23 - Air pipe
24 - Seal
25 - Throttle valve module - J338- / throttle valve module - GX3-
❑ Removing and installing ⇒ “4.5 Removing and installing throttle valve module J338 ”, page 236
4. Intake manifold 223

26 - Bolt
❑ Thread-forming
❑ 7.5 Nm
27 - Air hose
❑ With screw-type clip
❑ Tightening torque ⇒ “2.2 Exploded view - hose connections for charge air system”, page 211
28 - Bolt
❑ Thread-forming
❑ 6 Nm
29 - Retainer
❑ For air pipe
30 - Bolt
❑ 20 Nm
31 - O-ring
32 - Charge pressure sender - G31-
33 - Bolt
❑ Thread-forming
❑ 7.5 Nm
34 - Bolt
❑ Thread-forming
❑ 7.5 Nm
35 - Retainer
❑ For coolant valve for cylinder head - N489-
36 - Gasket
Intake manifold (top section) onto intake manifold (bottom sec‐

tion) - tightening torque and sequence
A - Intake manifold (top section) onto old intake manifold (bottom
section)
1. -1 … 14- Fit and screw in bolts by hand so that
they are screwed into old thread.
2. -1 … 14- 10 Nm

B - Intake manifold (top section) onto new intake manifold (bottom

section)
1. -1 … 4- 10 Nm
2. -5 … 14- 14 Nm
3. -1 … 4- 14 Nm
Retaining clamp for high-pressure pipe - tightening torque

♦ Thread-forming
♦ Fit and screw in bolt by hand so that it is screwed into old
thread. Then tighten bolt to torque.
♦ 7.5 Nm
4.1.2 Exploded view - intake manifold, vehicles with electric compressor

1 - Bolt
❑ 9 Nm
2 - Pipe
lation
3 - Seal
4 - Bolt
❑ 9 Nm
5 - Bolt
❑ 9 Nm
6 - Bracket
❑ For air pipe and exhaust
change-over valve -
N345-
7 - Intake manifold flap motor -
V157-
flap motor V157 ”,
page 234
8 - Gasket
9 - Intake manifold (top sec‐
tion)
⇒ page 228
❑ With retaining clamp
11 - Bolt
❑ Thread-forming
❑ 7.5 Nm
12 - Retainer
❑ For electrical wiring harness
13 - Bolt
❑ Thread-forming
❑ 7.5 Nm
14 - Ball stud
❑ Thread-forming
❑ 4 Nm
15 - Bolt
❑ Thread-forming
❑ 7.5 Nm

16 - Retainer
❑ For coolant hoses
17 - Bolt
18 - Seal
❑ 16x
19 - Bolt
❑ 9 Nm
20 - Seal
❑ 16x
21 - Intake manifold (bottom section)
22 - Bolt
❑ Thread-forming
❑ 7.5 Nm
23 - Bolt
❑ 9 Nm
24 - Air pipe
25 - Seal
26 - Bolt
❑ 9 Nm
27 - Throttle valve module - J338-
28 - Dowel pin
29 - Bolt
❑ 9 Nm
30 - Connection
31 - Not fitted
32 - Connection
33 - Not fitted
34 - Connection
35 - Bracket
❑ For air pipe
36 - Bolt
❑ 20 Nm
37 - Bolt
❑ Thread-forming

❑ 6 Nm
38 - O-ring
39 - Charge pressure sender - G31-
40 - Bolt
❑ Thread-forming
❑ 7.5 Nm
41 - Bolt
❑ Thread-forming
❑ 7.5 Nm
42 - Retainer
❑ For coolant valve for cylinder head - N489-
43 - Gasket
4.2 Removing and installing intake manifold

(top section)
⇒ “4.2.1 Removing and installing intake manifold (top section) -
vehicles without electric compressor”, page 228
⇒ “4.2.2 Removing and installing intake manifold (top section) -
vehicles with electric compressor”, page 232
4.2.1 Removing and installing intake manifold

(top section) - vehicles without electric
compressor
Removing
Intake manifold; Removing and installing intake manifold (top
section) .
– Remove throttle valve module - J338- ⇒ page 236 .

– Disconnect fuel hoses -1, 2, 3- ⇒ Fuel supply system; Rep.

gr. 20 ; Plug-in connectors; Disconnecting plug-in connectors .
– Unplug electrical connector -1- for fuel pressure sender for low
pressure - G410- .
– If installed, move electrical connector -4- for exhaust gas tem‐
perature sender 4 - G648- clear.
– Move electrical wiring harnesses -2- and fuel hose -arrow-
clear at bracket -3-.
– Unclip bracket from high-pressure lines and push to one side.
– Unplug electrical connectors on glow plugs.
– Move fuel hose -3- clear.

– Move electrical wiring harness -4- clear at wiring duct -2-.
– Unscrew bolt -1- (left and right) and detach wiring duct.
– Move fuel return hose -5- clear at intake manifold and high-
pressure pipe.
– If fitted, disconnect vacuum hose -4- and move hose clear at

bracket.
– Detach electrical connectors -1 and 2- from bracket, unplug
and move electrical wiring clear.
– Unclip bracket -3- from high-pressure lines and detach.
– Unclip bracket -5- from high-pressure pipes and move to one
side together with SCR line.

– Unscrew bolts -arrows- and remove retaining clips.
WARNING
The fuel system is pressurised.

Risk of injury as fuel may spray out.
♦ Put on protective gloves.
♦ Release pressure (wrap clean cloth around connection
and open connection carefully).
– Unscrew union nuts -1, 2- and detach high-pressure pipe.
– Unplug electrical connector -2- for exhaust gas recirculation

control motor - V338- .
– Unscrew union nuts -arrows- and detach high-pressure pipe
-1-.
– Remove bolt -1- and push guide tube -2- for oil dipstick slightly
towards front.

– Disconnect vacuum hose -2- from actuator for exhaust gas

recirculation.
– Detach changeover valves -1, 3- from bracket and move clear
to side.
– Unplug electrical connectors:

1 - For intake manifold flap motor - V157-
3 - For charge pressure sender - G31-
– Remove bolts -1- for exhaust gas recirculation pipe and bolts
-2- on bracket for air pipe.
– Remove bolts -arrows- and detach oil filler neck -1-.

– Seal off opening with plug from engine bung set - VAS 6122-
(clean plug thoroughly).
– Move coolant hose leading to injector for reducing agent -
N474- clear at intake manifold.

– Remove bolts -arrows- and move automatic glow period con‐

trol unit - J179- to one side together with bracket.
– Loosen and remove bolts in the sequence -14 ... 1- and detach
intake manifold (top section).
– If necessary, move electrical wiring clear.
Installing
Note
Renew seals after removing.
– Install high-pressure pipes ⇒ page 265 .

– Install throttle valve module - J338- ⇒ page 236 .
ltr. 4-valve common rail; Rep. gr. 23 ; Intake manifold; Removing
and installing intake manifold (top section) .
Tightening torques
♦ ⇒ Fig. ““Intake manifold (top section) onto intake manifold
(bottom section) - tightening torque and sequence”“ ,
page 224
♦ ⇒ “3.2 Exploded view - cylinder head cover”, page 110
♦ Dipstick guide tube ⇒ Item 8 (page 162)
♦ ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier;
Exploded view - lock carrier

(top section) - vehicles with electric com‐
pressor
4-valve common rail; Rep. gr. 23 ; Intake manifold; Removing
and installing intake manifold (top section) .

(bottom section)

Removing
– Remove exhaust gas recirculation cooler ⇒ page 314 .
Bottom section of intake manifold (right-side):
– Vehicles without electric compressor: Remove coolant pipe
(bottom front) for turbocharger ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes; Remov‐
ing and installing coolant pipes .
– Vehicles with electric compressor: Remove coolant pipe 2 for
turbocharger ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common
rail; Rep. gr. 19 ; Coolant pipes; Removing and installing
coolant pipes .
– Press coolant pipe (top right) downwards.
– Remove bolt -arrow- for retaining clip.


– If necessary, move electrical wiring/vacuum lines clear.
– Unscrew bolts -arrows- and detach intake manifold (bottom
section) -1-.
Note
The illustration shows the installation position on cylinder bank 2

(left-side) as an example.
Installing
Note
– Install exhaust gas recirculation cooler (front) ⇒ page 314 .

Tightening torques
♦ ⇒ Fig. ““Retaining clamp for high-pressure pipe - tightening
torque”“ , page 225

flap motor - V157-
⇒ “4.4.1 Removing and installing intake manifold flap motor V157
- vehicles without electric compressor”, page 234
⇒ “4.4.2 Removing and installing intake manifold flap motor V157
- vehicles with electric compressor”, page 236

flap motor - V157- - vehicles without
electric compressor
Removing
– Remove throttle valve module - J338- ⇒ page 236 .

– Disconnect vacuum hose -2- from actuator for exhaust gas

recirculation.
– Detach changeover valve -3- from bracket and move clear to
side.
– Remove bolt -1- and push guide tube -2- for oil dipstick slightly
towards front.
– Unplug electrical connectors:

1 - For intake manifold flap motor - V157-
3 - For charge pressure sender - G31-
– Remove bolts -1- for exhaust gas recirculation pipe and bolts
-2- on bracket for air pipe.

– Unscrew bolts -arrows- using socket Torx T30 - T10405- and

detach air pipe -2- together with intake manifold flap motor -
V157- -item 1-.
Installing
Note
– Install throttle valve module - J338- ⇒ page 236 .

page 10 .
Tightening torques
♦ ⇒ “4.1.1 Exploded view - intake manifold, vehicles without
electric compressor”, page 222
♦ Dipstick guide tube ⇒ Item 8 (page 162)

flap motor - V157- - vehicles with electric
compressor
and installing intake manifold flap motor - V157- .
4.5 Removing and installing throttle valve

module - J338-
⇒ “4.5.1 Removing and installing throttle valve module J338 - ve‐
hicles without electric compressor”, page 236
⇒ “4.5.2 Removing and installing throttle valve module J338 - ve‐
hicles with electric compressor”, page 237
4.5.1 Removing and installing throttle valve

module - J338- - vehicles without elec‐
tric compressor
Removing
Intake manifold; Removing and installing throttle valve module -
J338- .


– Remove bolts -arrows- and detach throttle valve module -
J338- .
Installing
Note

ltr. 4-valve common rail; Rep. gr. 23 ; Intake manifold; Removing
and installing throttle valve module - J338- .
page 10 .
Tightening torques
♦ ⇒ “4.1.1 Exploded view - intake manifold, vehicles without
electric compressor”, page 222
4.5.2 Removing and installing throttle valve

module - J338- - vehicles with electric
compressor
and installing throttle valve module - J338- .

5 Injectors/high-pressure reservoir
(rail)
⇒ “5.1 Exploded view - injectors”, page 238
⇒ “5.2 Checking injectors”, page 242
⇒ “5.3 Performing adaption of correction values for injectors”,
page 243
⇒ “5.4 Checking for injectors sticking open”, page 244
⇒ “5.5 Checking return flow rate of injectors with engine running”,
page 246
⇒ “5.6 Checking return flow rate of injectors at starter cranking
speed”, page 250
⇒ “5.7 Checking pressure retention valve in fuel return line”, page
253
⇒ “5.8 Removing and installing injectors”, page 255
⇒ “5.9 Installing high-pressure pipes”, page 265
⇒ “5.10 Removing and installing high-pressure reservoir (rail)”,
page 267
5.1 Exploded view - injectors

1 - Support bracket
❑ For clamping piece
❑ Different tightening tor‐
ques:
♦ To camshaft bearing
⇒ page 132
♦ To cylinder head: 9 Nm
2 - Clamping piece
❑ Use a coloured pen to
mark injectors and cor‐
responding clamping
piece and cylinder for
re-installation; pay at‐
tention to markings
when installing
❑ If the injector is installed
on another cylinder for
testing purposes, the
clamping piece must al‐
so be moved
❑ After looking for the
fault, the injector and the
clamping piece must be
re-installed on their orig‐
inal cylinder
❑ The clamping pieces
can be re-used when in‐
stalling new injectors
3 - Bolt
❑ 6 Nm +90°
4 - Fuel return hose
❑ From injectors
❑ Do not dismantle
❑ Only renew together with pressure retention valve
❑ After renewing, engine must be run at idling speed for approx. 2 minutes to bleed fuel system
❑ Then check fuel return hoses for leaks
❑ From high-pressure reservoir (rail) to injector
❑ Do not alter shape
❑ Mark allocation for re-installation; pay attention to marking when installing
❑ Check for damage before re-installing
❑ Lubricate threads of union nuts with clean engine oil
❑ Tightening torques for vehicles without electric compressor:
♦ 25 Nm if re-installing high-pressure pipe
♦ 15 Nm +60° if installing a new high-pressure pipe
❑ Tightening torques for vehicles with electric compressor:
6 - High-pressure reservoir (rail)
5. Injectors/high-pressure reservoir (rail) 239


❑ From high-pressure reservoir (rail) on opposite side
8 - Retaining clamp
❑ For high-pressure pipe
9 - Bolt
❑ 9 Nm
❑ From high-pressure pump to high-pressure reservoir (rail)
11 - Bolt
❑ 9 Nm
12 - Fuel pressure sender - G247-
❑ Use socket - T40218- to loosen and tighten
13 - O-ring
14 - Injector
❑ Use a coloured pen to mark allocation of injectors to corresponding clamping piece and high-pressure
pipe, and to corresponding cylinder for re-installation; pay attention to markings when installing
❑ If the injector is installed on another cylinder for testing purposes, the clamping piece must also be moved
❑ Renew copper seal after removing
❑ After looking for the fault (switching the injectors around), the injector and the clamping piece must be
re-installed on their original cylinder

❑ To remove carbon deposits from the injector sealing surface, clean the injector bore in the cylinder head
with cleaning kit - VAS 6811- (it is important to do this to avoid leaks)
15 - O-ring
16 - Copper seal
❑ Copper seal without chamfer: has no specified installation position
❑ Copper seal with chamfer: note installation position ⇒ page 242
Banjo bolt for fuel return line connection - tightening torque
Note

angle.
♦ Renew seals after removing.
– Tighten banjo bolt -arrow- to 8 Nm +90°.
Fuel pressure regulating valve - N276-

Version 1
♦ With deformable sealing lip
♦ Cannot be re-installed
♦ Removing and installing ⇒ page 275
♦ Performing adaptions required after renewing a component
(using ⇒ Vehicle diagnostic tester)
page 10
– Position fuel pressure regulating valve - N276- so that electri‐
cal wiring is not under tension when connector is plugged in.
– Tighten union screw on regulating valve in stages as follows
(counterhold hexagon flats on housing):

Version 2
♦ With deformable sealing lip
♦ Cannot be re-installed
♦ Removing and installing ⇒ page 278
♦ Performing adaptions required after renewing a component
(using ⇒ Vehicle diagnostic tester)
page 10
Tightening torque for versions 1 and 2
Stage Tightening torque
1. Screw in by hand until contact is made
2. 60 Nm
3. Turn back by 90°
4. 85 Nm
Fuel pressure sender - G247- - tightening torque
Note
Do not use an open-end spanner for loosening or tightening.
– Use socket, 27 mm - T40218- to tighten fuel pressure sender

- G247- -arrow- in stages as follows:
Stage Tightening torque
1. Screw in by hand until contact is made
2. 60 Nm
3. Turn back by 180°
4. 85 Nm
Note installation position for copper seal with chamfer
5.2 Checking injectors

There are four different tests for checking the operation of the
injectors.

♦ Performing adaption of correction values for injectors

⇒ page 243
♦ Checking for injectors sticking open ⇒ page 244
♦ Checking return flow rate of injectors with engine running
⇒ page 246
♦ Checking return flow rate of injectors at starter cranking speed
⇒ page 250
Perform the following tests first if the engine does not start at all:
♦ Checking for injectors sticking open ⇒ page 244
♦ Checking return flow rate of injectors at starter cranking speed
⇒ page 250
♦ Checking fuel pressure regulating valve - N276- ⇒ 6-cylinder
TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 23 ; Senders
and sensors; Removing and installing fuel pressure regulating
valve - N276- .
5.3 Performing adaption of correction val‐

ues for injectors
♦ The “Injector delivery calibration” and “Injector voltage cali‐

bration” serve to correct the injection rates for each cylinder of
a common rail system individually across the entire operating
range.
♦ The 7-digit adaption value -1- (example) is marked separately
on each injector. It may consist of letters and/or numbers (AS‐
CII code).
♦ Reference table for reading out letters and/or numbers on
each injector

– Perform adaption ⇒ Vehicle diagnostic tester.
– When a new injector is installed, the adaption value for the new
injector must be stored in the engine control unit.
– Additionally, check that the “Injector delivery calibration val‐
ues” with “Injector voltage calibration values” are correctly
entered for all the other injectors. Do NOT attempt to re-enter
these values if the correct values are already stored in the en‐
gine control unit.
– When the engine control unit is renewed, the appropriate “In‐
jector delivery calibration values” with “Injector voltage cali‐

bration” values must be written into the new engine control

unit.
5.4 Checking for injectors sticking open
Note
If one of the injectors is sticking open, this means that the injector
needle is not closing fully and fuel escapes into the cylinder.

♦ Hand vacuum pump - VAS 6213-
♦ Adapter of return flow meter - VAS 6684-

Procedure
Caution


Injectors/high-pressure reservoir (rail); Checking for injectors
sticking open .
– Erase entries in engine control unit event memory ⇒ Vehicle
diagnostic tester.
– Clean all high-pressure reservoir (rail) connections with en‐
gine cleaner or brake cleaner and dry.
– Detach retaining clip -1- and disconnect fuel return hose -2-.

– Connect hand vacuum pump - VAS 6213- to fuel hose

-arrow-.
– Generate a vacuum of -500 mbar using hand vacuum pump -
VAS 6213- .
• If the vacuum reading remains the same for 30 seconds, the
injectors are OK.
• In the case of a faulty injector, the vacuum will fall back to 0 bar
within 2 to 3 seconds.
– If pressure drops, check injectors on individual cylinder banks.

– Detach bracket -2- with wiring harness from high-pressure
pipes towards front -arrow B- and push upwards slightly.
– Detach covers -1-.
– Disconnect fuel return hoses from injectors; to do so, press
down both tabs and at the same time pull centre piece up to
release connection -arrow A-.

– Detach covers -arrow-.
– If necessary, move bracket for electrical wiring harness clear.

– Re-connect air hose to throttle valve module - J338- .

release connection -arrow-.
– Connect adapter to return line connection of injector to be tes‐
ted after adapter has been cleaned and blown out.
– Generate a vacuum of -500 mbar using hand vacuum pump -
VAS 6213- .
• If the vacuum reading remains the same for 30 seconds, the
injector is OK.
• In the case of a faulty injector, the vacuum will fall back to 0 bar
within 2 to 3 seconds.
– Repeat test if necessary; note drop in vacuum reading on hand
vacuum pump - VAS 6213- .
– Renew faulty injectors ⇒ page 255 .
Assembling
Note
♦ Renew O-ring for fuel return line connection if it is damaged

or deformed.
♦ Lubricate O-rings with engine oil or assembly oil before instal‐
ling.
– Push the return line connections carefully over the new seals
and onto the injectors.
• The connection must engage audibly.
– Then press down release pin carefully.
ing from testing ⇒ Vehicle diagnostic tester.
ltr. 4-valve common rail; Rep. gr. 23 ; Injectors/high-pressure
reservoir (rail); Checking for injectors sticking open .
Note
If there is any air left in the fuel system, the engine may switch to
the backup mode ('emergency running' mode) during the road
test. Stop engine and erase event memory. Then continue the
road test.
5.5 Checking return flow rate of injectors

with engine running
Note
Each injector normally has a relatively low fuel return flow rate. If
the return flow rate at one injector is relatively high compared to
the other injectors, that injector is probably defective.


♦ Hose clamps, up to 25 mm - 3094-
♦ Return flow meter - VAS 6684-
♦ Fuel-resistant measuring container

Procedure
Caution


Injectors/high-pressure reservoir (rail); Checking return flow rate
of injectors with engine running .
– Clean all return line connections with engine cleaner or brake
cleaner and dry.

– Clamp off fuel return line downstream of pressure retention

valve using a hose clamp -3094- .





– Connect hoses of return flow meter -VAS 6684/1- to return line
connections of all six injectors.
Caution
Risk of damage to injectors due to increased engine speed.

♦ Do NOT press the accelerator during this test; the engine
must only run at idling speed.
– Start engine and run at idling speed for several minutes:

– When the engine is warm and running at idling speed, the re‐
turn flow rates at each of the 6 injectors must not differ by more
than a small amount.
Evaluating return flow rate:

1- Injectors OK. Return flow rate approx. identical on all injec‐
tors.
2- Injector for cylinder 3 not OK. Return flow rate greater than
three times the volume of smallest measured return flow
rate.
Note
There is a mechanical fault at the injector if the return flow rate is

greater than three times the volume of the smallest measured
return flow rate.
– If one injector has a significantly higher return flow rate than

the others it must be renewed ⇒ page 255 .

– Remove hose clamp, up to 25 mm - 3094- from fuel return line.

Assembling
Note

or deformed.
♦ Lubricate all O-rings with engine oil or assembly oil before in‐
stalling.
reservoir (rail); Checking return flow rate of injectors with engine
running .
Note
road test.
5.6 Checking return flow rate of injectors at

starter cranking speed
Note
♦ Only perform this test if the engine does not start at all.
♦ Each injector normally has a relatively low fuel return flow rate.
If the return flow rate at one injector is relatively high compared
to the other injectors, that injector is probably defective.

♦ Hose clamps, up to 25 mm - 3094-

♦ Return flow meter - VAS 6684-
♦ Fuel-resistant measuring container

Procedure
Caution


Injectors/high-pressure reservoir (rail); Checking return flow rate
of injectors with engine running .
– Clean all return line connections with engine cleaner or brake
cleaner and dry.
– Clamp off fuel return line downstream of pressure retention
valve using a hose clamp -3094- .





– Connect hoses of return flow meter -VAS 6684/1- to return line
connections of all six injectors.
– Operate starter three times (wait approx. 20 seconds each
time after operating starter to prevent it from overheating).
• Specification of return flow rate: 0 ml
– If fuel comes out of one injector, that injector must be renewed
⇒ page 255 .

– Remove hose clamp -3094- from fuel return line.

Assembling
Note

or deformed.
♦ Lubricate all O-rings with engine oil or assembly oil before in‐
stalling.
reservoir (rail); Checking return flow rate of injectors with engine
running .
Note
road test.
5.7 Checking pressure retention valve in

fuel return line
♦ Tester for fuel return system - VAS 6330-
Procedure
Injectors/high-pressure reservoir (rail); Checking pressure reten‐
tion valve in fuel return line .

Caution

♦ No dirt must be allowed to get into the disconnected return
line or the open connection on the injector.
– Detach cover -arrow-.

– Clean return line connection on cylinder 4 with engine cleaner/

brake cleaner and dry.
– Pull return line connection off cylinder 4; to do so, press both
tabs down and at the same time pull centre piece upwards
-arrow- to release connection.
– Connect tester for fuel return system - VAS 6330- between

return line connection on injector and return line.
– Start engine.
– Check pressure on pressure gauge.
♦ Specification: approx. 12 bar
– If specification is not attained, renew fuel return line with pres‐
sure retention valve and ring/hose connector.
reservoir (rail); Checking pressure retention valve in fuel return
line .

5.8 Removing and installing injectors

⇒ “5.8.1 Removing injectors - cylinder bank 1 (right-side)”,
page 255
⇒ “5.8.2 Removing injectors - cylinder bank 2 (left-side)”,
page 259
⇒ “5.8.3 Installing injectors”, page 263
5.8.1 Removing injectors - cylinder bank 1

(right-side)
♦ Cleaning kit - VAS 6811- (not illustrated)
♦ Puller - T10055- with adapter - T10055/1-
♦ Assembly sleeve - T10377-

♦ Socket - T40055-
♦ Puller - T40059-
Removing
Caution


Injectors/high-pressure reservoir (rail); Removing and installing
injectors .
pressure - G410- .


– If fitted, detach covers -1-.
Version without noise insulation:

– Unplug electrical connectors -4- at injectors.
WARNING

• Put on safety goggles.
• Put on protective gloves.
• Release pressure (wrap a clean cloth around connection
– Unscrew union nuts -3- and detach high-pressure pipe.
Caution
Used injectors must always be re-installed on the same cylin‐

der.
♦ Mark injectors to ensure that they are re-installed at the
correct cylinders.
– Mark position of clamping piece -2- in relation to injector with

paint for re-installation.
– Unscrew bolt -1- and remove clamping piece.
Note
If it is not possible to remove the clamping piece, detach injector.

Version with noise insulation:

WARNING

– Remove union nuts -arrows- and bolts -1- and move fuel rail
to one side.

insulation.
Caution

der.
correct cylinders.
– Mark position of clamping piece -1- in relation to injector -2-

with paint for re-installation.
– Remove bolt -arrow- and detach clamping piece.
Note

– Fit puller - T10055- with adapter -T10055/1- on injector -2-, as
– Detach injector with clamping piece -1-.

– If puller - T10055- with adapter -T10055/1- cannot be fitted

directly, use puller - T40059- with corresponding bolt -1- in
addition.
– Place removed injectors on a clean cloth.
5.8.2 Removing injectors - cylinder bank 2

(left-side)
♦ Cleaning kit - VAS 6811- (not illustrated)
♦ Puller - T10055- with adapter - T10055/1-
♦ Assembly sleeve - T10377-

♦ Socket - T40055-
♦ Puller - T40059-
Removing
Caution


injectors .
bracket.
trical wiring clear.
– Unclip bracket -3- from high-pressure lines and move to one
– Unclip bracket -5- from high-pressure lines and press to one
side together with electrical wiring harness.

– If fitted, detach covers -1-.

– Unplug electrical connectors -arrows-.

– Move electrical connector -1- for injector for reducing agent -

N474- clear at bracket -2-.
– Unscrew bolts -arrows- and detach bracket.

Version without noise insulation:
WARNING

– Unscrew union nuts -3- and detach high-pressure pipe.
Caution

der.
correct cylinders.
– Mark position of clamping piece -2- in relation to injector with

paint for re-installation.
– Unscrew bolt -1- and remove clamping piece.
Note
Version with noise insulation:
WARNING

– Remove union nuts -arrows- and bolts -2- and detach fuel rail
-1-.


insulation.
Caution

der.
correct cylinders.
– Mark position of clamping piece -1- in relation to injector -2-

with paint for re-installation.
– Remove bolt -arrow- and detach clamping piece.
Note

– Fit puller - T10055- with adapter -T10055/1- on injector -2-, as
– Detach injector with clamping piece -1-.
– If puller - T10055- with adapter -T10055/1- cannot be fitted

directly, use puller - T40059- with corresponding bolt -1- in
addition.
– Place removed injectors on a clean cloth.
5.8.3 Installing injectors

Installing new injectors
When installing a new injector, the following components must be
renewed:
♦ Bolt for clamping piece
♦ Copper seal
♦ O-ring for injector bore
♦ O-ring for fuel return line connection

Installing used injectors

When re-installing a used injector in the same cylinder, the fol‐
lowing components must be renewed:
♦ Bolt for clamping piece
♦ Copper seal
♦ O-ring for injector bore
♦ O-ring for fuel return line connection
– Spray tip of injector nozzle with rust-solvent spray. Wait ap‐
prox. 5 minutes and wipe off soot particles and oil with a cloth.
– To remove the old copper seal from the injector, clamp the seal
carefully in a vice so that it is just held between the jaws without
turning. Then carefully pull and twist the injector out of the
copper seal by hand.
– Clean off deposits under the copper seal using a suitable scra‐
per.
Continued (same procedure for used and new injectors):
Caution
Risk of damage to injector sealing surface.

♦ To remove carbon deposits from the injector sealing sur‐
face, clean the injector bore in the cylinder head with
cleaning kit - VAS 6811- .
– Fit new copper seal.

– Lubricate all O-rings with engine oil or assembly oil before in‐
stalling.

– Renew O-ring for injector bore using assembly sleeve -

T10377- .
– Install injectors.
note the following:
Note
Lubricate all O-rings with engine oil or assembly oil before instal‐
ling.
– Carefully press down release pin.
page 10 .
reservoir (rail); Removing and installing injectors
Tightening torques
♦ ⇒ “5.1 Exploded view - injectors”, page 238
tem”, page 211
5.9 Installing high-pressure pipes

♦ Ratchet - V.A.G 1331/1-

♦ Open end spanner insert, AF 17 - V.A.G 1331/6-
♦ Socket - T40055-
Procedure
Note
♦ Before re-installation, check taper seats for deformation,

cracks, damage, scores and corrosion; renew high-pressure
pipes if they are damaged or corroded.
♦ Check that bore in pipe is not distorted, restricted or damaged
in any other way.
♦ When re-installing "old" high-pressure pipe, observe marking
for installation position.
– Use vacuum cleaner to remove dirt from taper seat at high-

pressure reservoir (rail).
– Clean fuel pipe and end of pipe with engine cleaner or brake
cleaner and dry.
– Lubricate threads of union nuts with clean engine oil.
– Hand-tighten union nuts on high-pressure pipes until they
make contact (ensure that pipes are not under tension).

17 mm union nuts on high-pressure reservoir (rail):

– To secure high-pressure pipes, use torque wrench - V.A.G
1331- with tool insert, AF 17 - V.A.G 1331/6- .
17 mm union nuts on injectors:

– To tighten unions of injectors, use torque wrench - V.A.G
1331- with ratchet - V.A.G 1331/1- and socket - T40055- .
Tightening torques
♦ ⇒ “3.2 Exploded view - cylinder head cover”, page 110
5.10 Removing and installing high-pressure

reservoir (rail)
♦ Open end spanner insert, AF 17 - V.A.G 1331/6-

♦ Socket - T40055-
Removing
Caution


high-pressure reservoir (rail) .
pressure - G410- .

– Detach retaining clip -1- and disconnect fuel return hose -2-.

WARNING

– Remove union nuts -arrows- and bolts -1- and detach fuel rail.

bracket.
– Detach electrical connectors -2- from bracket, unplug and
move electrical wiring clear.
– Unclip bracket -3- from high-pressure lines and move to one
– Unclip bracket -5- from high-pressure lines and press to one
side together with electrical wiring harness.

– Remove electrical connector -2- for injector for reducing agent

- N474- from bracket.
– Unplug electrical connector -1- for injector, cylinder 4 - N33- .

WARNING

– Remove union nuts -arrows- and bolts -2- and detach fuel rail
-1-.

– Unplug electrical connector -arrow-.

– Seal off open lines and connections with plugs (thoroughly
cleaned) from engine bung set - VAS 6122- .
Installing
reservoir (rail); Removing and installing high-pressure reservoir
(rail) .
Tightening torques
tem”, page 211

6 Senders and sensors

⇒ “6.1 Removing and installing air mass meter G70 ”, page 272
⇒ “6.2 Removing and installing fuel temperature sender G81 ”,
page 272
⇒ “6.3 Removing and installing fuel pressure sender G247 ”, page
272
⇒ “6.4 Removing and installing fuel pressure sender for low pres‐
sure G410 ”, page 274
⇒ “6.5 Checking fuel pressure regulating valve N276 ”,
page 275
⇒ “6.6 Removing and installing fuel pressure regulating valve
N276 ”, page 275
⇒ “6.7 Removing and installing pressure differential sender G505
”, page 279
6.1 Removing and installing air mass meter

- G70-
4-valve common rail; Rep. gr. 23 ; Senders and sensors; Re‐
moving and installing air mass meter - G70- .
6.2 Removing and installing fuel tempera‐

ture sender - G81-
Removing
– Remove exhaust gas recirculation cooler (front)
⇒ page 314 .
– Remove bolt -1- and detach fuel temperature sender - G81-
from connection.
Installing
– Install exhaust gas recirculation cooler (front) ⇒ page 314 .
Tightening torques
♦ ⇒ “7.1 Exploded view - high-pressure pump”, page 280
6.3 Removing and installing fuel pressure

sender - G247-
Note
♦ The fuel pressure sender - G247- continuously measures the

fuel pressure in the high-pressure system. It transmits a cor‐
responding voltage signal to the engine control unit - J623- .
♦ Should the fuel pressure sender fail, the engine control unit
will control the fuel pressure via a mapped open-loop backup
function. Maximum engine speed in this mode is restricted.
♦ The fuel pressure sender - G247- has a deformable sealing
lip.

♦ Socket - T40218-
Removing
Senders and sensors; Removing and installing fuel pressure
sender - G247- .
Caution

– Unscrew bolt -2- and release screw-type clip.

– Detach injector for reducing agent - N474- -item 1- and place
to one side.
– Clean area all around fuel pressure sender - G247- with en‐
gine cleaner or brake cleaner and dry.
Note
♦ Clean carefully; cleaning solution must not enter the electrical

connector.
♦ Make sure no dirt gets into opening in high-pressure reservoir
(rail).
6. Senders and sensors 273

– Unplug electrical connector -arrow-.
Note
Do not use an open-end spanner for loosening or tightening.
– Unscrew fuel pressure sender - G247- using socket, 27 mm -

T40218- .
– Remove dirt from opening in high-pressure reservoir (rail) us‐
ing a vacuum cleaner. Do not use metal tools, etc.
– Seal off hole in high-pressure reservoir (rail) with a plug (thor‐
oughly cleaned) from engine bung set - VAS 6122- .
Installing
Note
♦ If the deformable sealing lip and the thread of the fuel pressure
sender - G247- are not damaged, the sender can be re-used
once.
♦ Check sealing surface at opening in high-pressure reservoir.
♦ Check that the deformable sealing lip and the thread on the
new fuel pressure sender are not damaged.
♦ The beginning of the thread and the deformable sealing lip of
the fuel pressure sender must be coated with diesel fuel.
– Screw in fuel pressure sender - G247- by hand until it makes

contact and then tighten.
– Install injector for reducing agent - N474- ⇒ page 302 .
ltr. 4-valve common rail; Rep. gr. 23 ; Senders and sensors; Re‐
moving and installing fuel pressure sender - G247- .
Tightening torques
♦ ⇒ Fig. ““ Fuel pressure sender -G247- - tightening torque”“ ,
page 242

sender for low pressure - G410-
Removing
Senders and sensors ; Removing and installing fuel pressure
sender for low pressure - G410- .
Caution

♦ Observe rules for cleanliness when working on the fuel
supply system ⇒ page 7 .


– Unscrew fuel pressure sender for low pressure - G410-
-item 2- (counterhold at connection -3-).
Installing
– Screw in fuel pressure sender for low pressure - G410- by
hand until it makes contact and then tighten.
ltr. 4-valve common rail; Rep. gr. 23 ; Senders and sensors ;
Removing and installing fuel pressure sender for low pressure -
G410- .
Tightening torques
♦ ⇒ Fig. ““ Fuel pressure sender for low pressure -G410- - tight‐
ening torque”“ , page 282
6.5 Checking fuel pressure regulating valve

- N276-
4-valve common rail; Rep. gr. 23 ; Senders and sensors; Check‐
ing fuel pressure regulating valve - N276- .

regulating valve - N276-
⇒ “6.6.1 Removing and installing fuel pressure regulating valve
N276 - version 1”, page 275
⇒ “6.6.2 Removing and installing fuel pressure regulating valve
N276 - version 2”, page 278
6.6.1 Removing and installing fuel pressure

regulating valve - N276- - version 1
Versions of fuel pressure regulating valve - N276-
⇒ Fig. ““ Fuel pressure regulating valve -N276- ”“ , page 241
Note
♦ The fuel pressure regulating valve - N276- maintains a con‐

stant pressure in the high-pressure reservoir (rail) and the
injector pipes (high-pressure fuel circuit).
♦ It is not possible to start engine if fuel pressure regulating valve
- N276- is defective.
♦ If the pressure in the high-pressure fuel circuit is too high, the
regulating valve opens to allow some of the fuel to flow back
from the high-pressure reservoir (rail) to the fuel tank via a
return hose.
♦ If the pressure in the high-pressure fuel circuit is too low, the
valve closes and seals off the high-pressure section of the
system from the low-pressure section.
♦ The fuel pressure regulating valve - N276- has a deformable
sealing lip and can only be used once. Do not install it for test
purposes.


♦ Open end spanner insert, AF 30 - T10553-
Removing
Senders and sensors; Removing and installing fuel pressure reg‐
ulating valve - N276- .
Caution

– Clean thread and area around fuel pressure regulating valve

- N276- with engine cleaner or brake cleaner and dry.
• Make sure no dirt gets into opening in high-pressure reservoir.
• Clean carefully; cleaning solution must not enter the electrical
connector.
– Remove banjo bolt for fuel return hoses.
– Unplug electrical connector -arrow- at fuel pressure regulating
valve - N276- .

– Loosen union screw using open-end spanner insert, 30 mm -

T10553- (at the same time, counterhold at hexagon flats on
housing). Then unscrew and remove by hand.
– Extract dirt from opening in high-pressure reservoir (thread
and sealing surface) using a vacuum cleaner. Do not use met‐
al tools, etc.
– Seal off open connection in high-pressure reservoir (rail) with
a plug (thoroughly cleaned) from engine bung set - VAS
6122- .
Installing
Note
♦ Fuel pressure regulating valve - N276- must always be re‐

newed after it has been removed.
new regulating valve are not damaged.
♦ Coat beginning of thread, deformable sealing lip and O-ring of
regulating valve lightly with diesel fuel.
– Tighten union nut by hand.
– Position fuel pressure regulating valve - N276- so that electri‐

cal wiring is not under tension when connector -arrow- is
plugged in.
– Counterhold hexagon flats on regulating valve housing in this
position with open-end spanner and tighten union screw with
open-end spanner insert, 30 mm - T10553- .
page 10 .
Tightening torques
♦ ⇒ Fig. ““ Fuel pressure regulating valve -N276- ”“ , page 241

6.6.2 Removing and installing fuel pressure

regulating valve - N276- - version 2
Versions of fuel pressure regulating valve - N276-
⇒ Fig. ““ Fuel pressure regulating valve -N276- ”“ , page 241
Note
♦ The fuel pressure regulating valve - N276- maintains a con‐

stant pressure in the high-pressure reservoir (rail) and the
injector pipes (high-pressure fuel circuit).
♦ It is not possible to start engine if fuel pressure regulating valve
- N276- is defective.
♦ If the pressure in the high-pressure fuel circuit is too high, the
regulating valve opens to allow some of the fuel to flow back
from the high-pressure reservoir (rail) to the fuel tank via a
return hose.
♦ If the pressure in the high-pressure fuel circuit is too low, the
valve closes and seals off the high-pressure section of the
system from the low-pressure section.
♦ The fuel pressure regulating valve - N276- has a deformable
sealing lip and can only be used once. Do not install it for test
purposes.

♦ Open end spanner insert, AF 30 - T10553-
Removing
– Remove high-pressure reservoir (rail) (right-side)
⇒ page 267 .

Note
The high-pressure reservoir can be clamped in a vice in order to

remove the pressure regulating valve; however, it is essential that
protective jaw covers are used. Do NOT take up the weight of the
high-pressure reservoir by the threaded connections for the high-
pressure pipes or the retaining tabs for the cylinder head.
– Clean thread and area around fuel pressure regulating valve

- N276- with engine cleaner or brake cleaner and dry.
• Make sure no dirt gets into opening in high-pressure reservoir.
• Clean carefully; cleaning solution must not enter the electrical
connector.
– Unscrew fuel pressure regulating valve - N276- -item 2- from
high-pressure reservoir -1- using open-end spanner insert,
30 mm - T10553- .
– Extract dirt from opening in high-pressure reservoir (thread
and sealing surface) using a vacuum cleaner. Do not use met‐
al tools, etc.
– Seal off open connection in high-pressure reservoir (rail) with
a plug (thoroughly cleaned) from engine bung set - VAS
6122- .
Installing
Note
♦ Fuel pressure regulating valve - N276- must always be re‐

newed after it has been removed.
new regulating valve are not damaged.
♦ Coat beginning of thread, deformable sealing lip and O-ring of
regulating valve lightly with diesel fuel.
– Tighten fuel pressure regulating valve - N276- using open-end

spanner insert, 30 mm - T10553- .
– Install high-pressure reservoir (rail) (right-side) ⇒ page 267 .
page 10 .
Tightening torques
♦ ⇒ Fig. ““ Fuel pressure regulating valve -N276- ”“ , page 241
6.7 Removing and installing pressure differ‐

ential sender - G505-
4-valve common rail; Rep. gr. 23 ; Senders and sensors; Re‐
moving and installing pressure differential sender - G505- .

7 High-pressure pump
⇒ “7.1 Exploded view - high-pressure pump”, page 280
⇒ “7.2 Removing and installing high-pressure pump”, page 282
7.1 Exploded view - high-pressure pump
❑ Check for damage be‐
fore re-installing
❑ Always renew high-
pressure pipe when re‐
newing high-pressure
pump
❑ Lubricate threads of un‐
ion nuts with clean en‐
gine oil
❑ Tightening torques for
vehicles without electric
compressor:
♦ 25 Nm if re-installing high-
pressure pipe
♦ 15 Nm +60° if installing a
new high-pressure pipe
❑ Tightening torques for
vehicles with electric
compressor:
♦ 35 Nm if re-installing high-
pressure pipe
♦ 15 Nm +60° if installing a
new high-pressure pipe
2 - High-pressure pump
Caution
Risk of malfunctions
caused by dirt.
Observe
♦ rules for cleanli‐
ness ⇒ page 7 .
Running when dry cau‐
ses irreparable damage
to high-pressure pump.
If♦the high-pressure
pump has been removed
and re-installed or re‐
newed, the first fuel filling
must be performed be‐
fore the engine is started
for the first time
⇒ page 217 .


❑ Always renew high-pressure pipe when renewing high-pressure pump
4 - O-rings
❑ Allocation ⇒ page 282
5 - Bolt
❑ Thread-forming
❑ 7.5 Nm
6 - Fuel temperature sender - G81-
7 - O-rings
8 - Bracket
❑ For fuel hoses
9 - Bolt
❑ 9 Nm
10 - Connection
❑ Fuel supply line
11 - Connection
❑ Fuel return line
12 - O-rings
❑ Allocation ⇒ page 282
13 - Nut
❑ To loosen, counterhold adapter -item 14- using counterhold tool - T40248- or counterhold tool - T40292-
♦ Vehicles without electric compressor: 70 Nm
♦ Vehicles with electric compressor: 20 Nm +50°
14 - Adapter
❑ For chain sprocket for high-pressure pump
❑ To loosen nut -item 13-, use counterhold tool - T40248- or counterhold tool - T40292-
7. High-pressure pump 281

15 - O-ring
16 - Bolt
❑ 23 Nm
Connection to bracket - tightening torque

– Tighten bolt -arrow- to 3.5 Nm.
Fuel pressure sender for low pressure - G410- - tightening torque

– Tighten fuel pressure sender for low pressure - G410-
-item 2- to 22 Nm.
Allocation of O-rings to connection -2-

1 - O-ring (blue)
3 - O-ring (blue)
4 - Green O-rings
7.2 Removing and installing high-pressure

pump

♦ Wrench, 21 mm - T40263-
♦ Counterhold tool - T40292-
Removing
High-pressure pump; Removing and installing high-pressure
pump .

– Remove emission control module ⇒ 6-cylinder TDI engine,

3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Emission control
system; Removing and installing emission control module .
– Remove coolant pipe (top right) ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 19 ; Coolant pipes; Remov‐
ing and installing coolant pipes .
– Remove coolant shut-off valve ⇒ page 198 .
– Unscrew bolts -1, 4- and remove bracket -2-.
– Unscrew bolts -arrows- and detach cover -3-.
Caution

slips.
-arrow-.

crankshaft until it is possible to lock chain sprocket for high-
pressure pump with locking pin - T40245- .
– Remove bolt -arrow- for retaining clip.

– Unplug electrical connector -1- for fuel temperature sender -

G81- .
WARNING

– Unscrew union nuts -arrows- and detach high-pressure pipe.
Unplug electrical connector -1- for fuel metering valve - N290- .

– Unscrew bolts -arrows- and detach high-pressure pump.
Note
For illustration purposes, the installation position is shown with

the exhaust gas recirculation pipe removed.
Installing
Note
♦ Renew seal and O-ring after removal.

♦ Always renew high-pressure pipes when renewing high-pres‐
sure pump.
– Use counterhold tool - T40292- to tighten nut -arrow- of adapt‐

er.

– Insert high-pressure pump into chain sprocket.

• The dual toothing -arrow A- on the chain sprocket must align
with the groove -arrow B- in the adapter on the high-pressure
pump shaft.
– Install coolant shut-off valve ⇒ page 198 .
– Install coolant pipe (top right) ⇒ 6-cylinder TDI engine, 3.0 ltr.
4-valve common rail; Rep. gr. 19 ; Coolant pipes; Removing
and installing coolant pipes .
ltr. 4-valve common rail; Rep. gr. 23 ; High-pressure pump; Re‐
moving and installing high-pressure pump .
page 10 .
Caution
Running when dry causes irreparable damage to high-pres‐

sure pump.
♦ After installing the high-pressure pump, the pump must
first be filled with fuel before the engine is started for the
first time ⇒ page 217 .
Tightening torques
♦ ⇒ “7.1 Exploded view - high-pressure pump”, page 280
♦ ⇒ Fig. ““Turbocharger - tightening torque and sequence”“ ,
page 205
♦ ⇒ Fig. ““Retaining clamp for high-pressure pipe - tightening
torque”“ , page 225
♦ ⇒ “1.1 Exploded view - timing chain cover”, page 65

8 Lambda probe
⇒ “8.1 Exploded view - Lambda probe”, page 287
⇒ “8.2 Removing and installing Lambda probe”, page 288
⇒ “8.3 Removing and installing NOx senders”, page 289
⇒ “8.4 Removing and installing particulate sensor G784 ”,
page 289
8.1 Exploded view - Lambda probe
1 - NOx sender 2 - G687- with

control unit for NOx sender 2 -
J881- / control unit 2 for NOx
sender - GX46-
⇒ 6-cylinder TDI en‐
gine, 3.0 ltr. 4-valve
common rail; Rep. gr.
23 ; Lambda probe
❑ Installation position var‐
ies
❑ 52 Nm
2 - Particulate sensor - G784-
ies depending on model
version ⇒ Current flow
diagrams, Electrical
fault finding and Fitting
locations
23 ; Lambda probe
❑ 52 Nm
3 - Pressure differential sender
- G505-
23 ; Senders and sen‐
sors; Removing and in‐
stalling pressure differ‐
ential sender - G505-
❑ Performing adaptions
required after renewing
a component (using ⇒ Vehicle diagnostic tester)
❑ Tighten pressure line to 45 Nm
❑ ⇒ Item 4 (page 305)
5 - NOx sender - G295- with control unit for NOx sender - J583- / control unit for NOx sender - GX30-
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 23 ; Lambda
probe
❑ 52 Nm
8. Lambda probe 287


❑ ⇒ Item 6 (page 305)
7 - Lambda probe - G39- with Lambda probe heater - Z19- / Lambda probe 1 before catalytic converter - GX10-
❑ Observe fitting instructions ⇒ page 289
❑ 52 Nm
❑ ⇒ Item 8 (page 305)
❑ Not fitted on all models ⇒ Current flow diagrams, Electrical fault finding and Fitting locations
❑ ⇒ Item 9 (page 305)
8.2 Removing and installing Lambda probe

♦ Lambda probe open ring spanner set - 3337-
Removing
Lambda probe; Removing and installing Lambda probe .

– Detach electrical connector -2- from bracket, unplug and move

electrical wire clear.
– Unscrew Lambda probe - G39- -item 1- using a tool from
Lambda probe open ring spanner set - 3337- .
Installing
Note
♦ Threads of new Lambda probes are already coated with as‐

sembly paste; the paste must not get into the slots on the probe
body.
♦ In the case of a used Lambda probe grease only the thread
with high-temperature paste. The paste must not get into the
slots on the Lambda probe body. For high-temperature paste
refer to ⇒ Electronic parts catalogue
♦ When installing, the Lambda probe wiring must always be re‐
attached at the same locations to prevent it from coming into
contact with the exhaust pipe.

ltr. 4-valve common rail; Rep. gr. 23 ; Lambda probe; Removing
and installing Lambda probe .
Tightening torque
♦ ⇒ “8.1 Exploded view - Lambda probe”, page 287
8.3 Removing and installing NOx senders

4-valve common rail; Rep. gr. 23 ; Lambda probe ; Removing and
installing NOx senders.
8.4 Removing and installing particulate sen‐

sor - G784-
4-valve common rail; Rep. gr. 23 ; Lambda probe ; Removing and
installing particulate sensor - G784- .
8. Lambda probe 289

9 Engine control unit

engine, 3.0 ltr. 4-valve common rail; Rep. gr. 23 ; Engine control
unit .

26 – Exhaust system
1 Exhaust pipes/silencers
⇒ “1.1 Exploded view - silencers”, page 291
⇒ “1.2 Removing and installing front exhaust pipe”, page 291
⇒ “1.3 Separating exhaust pipes/silencers”, page 291
⇒ “1.4 Removing and installing silencers”, page 291
⇒ “1.5 Stress-free alignment of exhaust system”, page 291
⇒ “1.6 Checking exhaust system for leaks”, page 291
1.1 Exploded view - silencers

4-valve common rail; Rep. gr. 26 ; Exhaust pipes/silencers; Ex‐
ploded view - silencers .
1.2 Removing and installing front exhaust

pipe
4-valve common rail; Rep. gr. 26 ; Exhaust pipes/silencers; Re‐
moving and installing front exhaust pipe .
1.3 Separating exhaust pipes/silencers

4-valve common rail; Rep. gr. 26 ; Exhaust pipes/silencers; Sep‐
arating exhaust pipes/silencers .
1.4 Removing and installing silencers

4-valve common rail; Rep. gr. 26 ; Exhaust pipes/silencers; Re‐
moving and installing silencers .
1.5 Stress-free alignment of exhaust system

4-valve common rail; Rep. gr. 26 ; Exhaust pipes/silencers;
Stress-free alignment of exhaust system .
1.6 Checking exhaust system for leaks

Procedure
WARNING
When working on all parts of the exhaust system:

♦ Observe safety precautions when working on the exhaust
system ⇒ page 3 .
– Start the engine and run at idling speed.

– Plug tailpipes during leak test (e.g. with cloth or plug).
– Listen for noise at the connection points of cylinder head/ex‐
haust manifold, turbocharger/front exhaust pipe etc. to locate
any leaks.
– Rectify any leaks that are found.
1. Exhaust pipes/silencers 291

2 Emission control system

⇒ “2.1 Exploded view - emission control system”, page 292
⇒ “2.2 Removing and installing emission control module”,
page 296
⇒ “2.3 Removing and installing trap catalytic converter”,
page 297
⇒ “2.4 Removing and installing exhaust flap control unit J883 ”,
page 298
2.1 Exploded view - emission control sys‐

tem
WARNING

system ⇒ page 3 .
Version 1
1 - Pipe
lation
2 - Nut
Rep. gr. 26 ; Exhaust
gas recirculation sys‐
tem; Exploded view - ex‐
haust gas recirculation
system
3 - Bolt
❑ 20 Nm
4 - Mounting
5 - Nut
❑ 25 Nm
6 - Gasket
❑ With pressure line for
pressure differential
sender - G505-
❑ If renewing emission
control module, dirt
screen must also be re‐
newed ⇒ 6-cylinder TDI
engine, 3.0 ltr. 4-valve
26 ; Exhaust gas recir‐
culation system; Explo‐
292 Rep. gr.26 - Exhaust system

ded view - exhaust gas

recirculation system
❑ Mounting components ⇒ page 296
8 - Screw-type clip
❑ 15 Nm
9 - Seal
10 - Turbocharger
11 - Front exhaust pipe
❑ With flexible joint; do not bend flexible joint more than 10° – otherwise it can be damaged
❑ Protect against knocks and impact
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust
pipes/silencers; Removing and installing front exhaust pipe
❑ Align exhaust system so it is free of stress ⇒ page 291
12 - Nut
❑ 25 Nm
13 - Gasket
14 - Exhaust flap control unit - J883-
15 - Trap catalytic converter
16 - Bolt
17 - Nut
❑ 9 Nm
18 - Gasket
Version 2
2. Emission control system 293

1 - Clamp
❑ Before fitting, wrap tape
around connection be‐
tween trap catalytic con‐
verter and exhaust gas
recirculation pipe
⇒ page 296
❑ Tighten screw connec‐
tions evenly to 30 Nm
2 - Bolt
❑ 20 Nm
3 - Mounting
4 - Nut
❑ 25 Nm
5 - Gasket
❑ With pressure line for
pressure differential
sender - G505-
❑ If renewing emission
control module, dirt
screen must also be re‐
newed ⇒ 6-cylinder TDI
engine, 3.0 ltr. 4-valve
26 ; Exhaust gas recir‐
culation system; Explo‐
ded view - exhaust gas
recirculation system
❑ Mounting components
⇒ page 296
7 - Screw-type clip
❑ 15 Nm
8 - Seal
9 - Turbocharger
10 - Front exhaust pipe
❑ With flexible joint; do not bend flexible joint more than 10° – otherwise it can be damaged
❑ Protect against knocks and impact
❑ Removing and installing ⇒ 6-cylinder TDI engine, 3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust
pipes/silencers; Removing and installing front exhaust pipe
❑ Align exhaust system so it is free of stress ⇒ page 291

11 - Nut
❑ 25 Nm
12 - Gasket
13 - Exhaust flap control unit - J883-
14 - Trap catalytic converter
❑ Wrap aluminium foil/glass cloth tape around connection between trap catalytic converter and exhaust
gas recirculation pipe ⇒ page 296
15 - Bolt
16 - Nut
❑ 9 Nm
Components of mountings (front) for front exhaust pipe on gear‐

box
1- Spacer sleeve
2- Compression spring
3- Washer
4- Bolt, 23 Nm
5- Bolt, 23 Nm
6- Spacer sleeve
7- Rubber buffer
8- Bracket
9- Spacer sleeve
Installation position of screw-type clip for emission control module

• Angle -α- = 90° ± 15°.

Mounting components for emission control module

1- Cage nut (integrated in emission control module)
2- Spacer sleeve
3- Compression spring
4- Washer
5- Bolt, 23 Nm
6- Bolt, 23 Nm
7- Spacer sleeve
8- Rubber buffer
9- Bracket
10 - Spacer sleeve
Wrapping aluminium foil/glass cloth tape around connection be‐

tween trap catalytic converter and exhaust gas recirculation pipe

♦ Aluminium foil/glass cloth tape, e.g. 3M 3635033
– Cut aluminium foil/glass cloth tape -1- to size of 134 ± 2 mm.
– Position aluminium foil/glass cloth tape at connection between
trap catalytic converter -2- and exhaust gas recirculation pipe
-3-.
• One half of the tape must lie on the trap catalytic converter and
the other on the exhaust gas recirculation pipe.
• When positioning the tape, start at the top of the pipe (area
between -arrows- in illustration).
– Bond on aluminium foil/glass cloth tape all around -arrows-.
Tape must be taut; smooth out any creases.
2.2 Removing and installing emission con‐

trol module
4-valve common rail; Rep. gr. 26 ; Emission control system; Re‐
moving and installing emission control module .

2.3 Removing and installing trap catalytic

converter
Removing
WARNING

system ⇒ page 3 .
– Remove nuts -arrows-.
Version 1:
– Remove nuts -arrows-.
Version 2:
– Wrap aluminium foil/glass cloth tape around connection be‐
tween trap catalytic converter and exhaust gas recirculation
pipe ⇒ page 296 .
– Release clamp -arrow- on exhaust gas recirculation pipe.


– Unplug electrical connector -1- for exhaust flap control unit -
J883- -item 2-.
– Loosen clamp -arrows- and push towards rear.

– Remove trap catalytic converter.
Installing
Note
Renew gaskets and self-locking nuts after removal.
Version 2:
– Wrap aluminium foil/glass cloth tape around connection be‐
tween trap catalytic converter and exhaust gas recirculation
pipe ⇒ page 296 .
– Slide clamp -arrow- as far as possible onto trap catalytic con‐
verter and tighten, paying attention to aluminium foil/glass
cloth tape.
page 10 .
Tightening torques
26 ; Exhaust pipes/silencers; Exploded view - silencers
♦ ⇒ “2.1 Exploded view - emission control system”, page 292
2.4 Removing and installing exhaust flap

control unit - J883-
WARNING

system ⇒ page 3 .

Removing
– Unscrew bolts -arrows- and remove exhaust flap control unit -
J883- .
Installing
Note
Renew bolts and nuts after removing.
– Fit exhaust flap control unit.

• Coupling -1- must engage in retainer of exhaust flap -2-.
– Tighten upper bolt first, then tighten lower bolt.

– Remove protective cap for electrical connector and plug con‐
nector -1- in. Secure heat insulation sleeve if necessary.
Tightening torques
♦ ⇒ “2.1 Exploded view - emission control system”, page 292

3 SCR (selective catalytic reduction)

system
⇒ “3.1 Exploded view - reducing agent tank”, page 300
⇒ “3.2 Exploded view - reducing agent supply line”, page 300
⇒ “3.3 Releasing pressure in SCR system”, page 301
⇒ “3.4 Draining reducing agent tank”, page 301
⇒ “3.5 Removing and installing reducing agent tank”, page 302
⇒ “3.6 Removing and installing injector for reducing agent N474
”, page 302
⇒ “3.7 Removing and installing control unit for reducing agent
metering system J880 ”, page 303
3.1 Exploded view - reducing agent tank

4-valve common rail; Rep. gr. 26 ; SCR (selective catalytic re‐
duction) system; Exploded view - reducing agent tank .
3.2 Exploded view - reducing agent supply line

2 - Retaining clamp
3 - Bolt
❑ 5 Nm
4 - Gasket
5 - Injector for reducing agent -
N474-
⇒ page 302
❑ Lugs in injector for re‐
ducing agent - N474-
must be inserted in cor‐
responding mountings
in front exhaust pipe.
❑ After renewing compo‐
nent(s) or draining re‐
ducing agent (opening a
reducing agent line),
perform required adap‐
tions using ⇒ Vehicle di‐
agnostic tester
⇒ “3.8 Performing adap‐
tions after renewing a
component”, page 10
6 - SCR supply line
❑ For reducing agent tank
❑ With heater for reducing
agent line (heater circuit
2) - Z104-
❑ Heater for reducing
agent line (heater circuit

2) - Z104- may consist of

several segments
❑ Disconnecting version with release catch ⇒ page 301
❑ Version with release tab: Press release tab to disconnect and connect
Disconnecting and connecting supply line - version with release

catch
Separating
WARNING
Safety risk due to escaping reducing agent.

♦ To prevent large amounts of reducing agent from escap‐
ing when the supply line is opened, wait until the reducing
agent has been drawn back automatically ⇒ page 5 .
Note
Hold a cloth under separating point to catch escaping reducing

agent.
– To disconnect supply line, press release catches in direction

of -arrows-.
Connecting
• Plug-in connector must engage audibly when connecting.
– Pull to check that plug-in connectors are correctly engaged.
3.3 Releasing pressure in SCR system

♦ Safety goggles
♦ Protective gloves
Procedure
WARNING
The SCR system is pressurised. Risk of injury as reducing

agent may spray out.
♦ Put on protective gloves.
♦ Release pressure (wrap a clean cloth around connection
– Disconnect quick connector at reducing agent tank or supply

line - version with release catch ⇒ page 301 .
3.4 Draining reducing agent tank

duction) system; Draining reducing agent tank .
3. SCR (selective catalytic reduction) system 301

3.5 Removing and installing reducing agent

tank
duction) system; Removing and installing reducing agent tank .
3.6 Removing and installing injector for re‐

ducing agent - N474-
Removing
SCR (selective catalytic reduction) system; Removing and instal‐
ling injector for reducing agent - N474- .
WARNING

system ⇒ page 3 .
Reducing agent can cause skin irritation.
♦ Observe safety measures when handling reducing agent
⇒ page 4 .
– Hold a cloth under separating point to catch escaping reducing

agent.
– Version with release catch: Disconnect supply line -2- from
injector for reducing agent - N474- ⇒ page 301 .
– Version with release tab: To disconnect, press release tab at
supply line -2-.
– Unplug electrical connector -1- and move electrical wire clear.
– Release retaining clip -3- and detach injector for reducing
agent - N474- .
– Disconnect and seal off coolant hoses -4-.

Installing
Note
♦ Renew gasket and retaining clip after removing.

• Installation position: lugs in injector for reducing agent - N474-

-item 1- must be inserted in corresponding mountings in emis‐
sion control module -2-.
– Connect supply line ⇒ page 301 .
ltr. 4-valve common rail; Rep. gr. 26 ; SCR (selective catalytic
reduction) system; Removing and installing injector for reducing
agent - N474-
After renewing component(s) or draining reducing agent (opening
a reducing agent line), perform required adaptions using ⇒ Vehi‐
cle diagnostic tester
page 10 .
Tightening torques
♦ ⇒ “3.2 Exploded view - reducing agent supply line”,
page 300
3.7 Removing and installing control unit for

reducing agent metering system - J880-
All procedures are described in ⇒ 6-cyl. TDI engine, 3.0 ltr. 4-
valve common rail; Rep. gr. 26 ; SCR (selective catalytic reduc‐
tion) system ; Removing and installing control unit for reducing
agent metering system - J880- .
3. SCR (selective catalytic reduction) system 303

4 Exhaust gas temperature control

⇒ “4.1 Exploded view - exhaust gas temperature control”,
page 304
⇒ “4.2 Removing and installing exhaust gas temperature sender 1
G235 ”, page 305
G448 ”, page 307
G495 ”, page 308
G648 ”, page 310
4.1 Exploded view - exhaust gas tempera‐

ture control
WARNING

system ⇒ page 3 .

1 - NOx sender 2 - G687- with

control unit for NOx sender 2 -
J881-
ies
❑ ⇒ Item 1 (page 287)
2 - Particulate sensor - G784-
❑ ⇒ Item 2 (page 287)
3 - Pressure differential sender
- G505-
❑ ⇒ Item 3 (page 287)
4 - Exhaust gas temperature
sender 3 - G495-
⇒ page 308
❑ 45 Nm
5 - NOx sender - G295- with
control unit for NOx sender -
J583-
❑ ⇒ Item 5 (page 287)
sender 2 - G448-
⇒ page 307
❑ 45 Nm
7 - Lambda probe - G39- with
Lambda probe heater - Z19-
❑ ⇒ Item 7 (page 288)
sender 1 - G235-
⇒ page 305
❑ 45 Nm
❑ Not fitted on all models ⇒ Current flow diagrams, Electrical fault finding and Fitting locations
❑ 45 Nm
4.2 Removing and installing exhaust gas

temperature sender 1 - G235-
4. Exhaust gas temperature control 305

♦ Tool set - T10395 A- with suitable tool insert
Removing
WARNING

system ⇒ page 3 .
Note

♦ When removing, the electrical wiring must not be cut, other‐
wise a fault diagnosis would no longer be possible.
– Remove emission control module ⇒ 6-cylinder TDI engine,

3.0 ltr. 4-valve common rail; Rep. gr. 26 ; Emission control
system; Removing and installing emission control module .
Exhaust gas temperature control; Removing and installing ex‐
haust gas temperature sender 1 - G235- .


– Remove exhaust gas temperature sender 1 - G235- -item 1-.
Installing
Note
♦ Take care to protect exhaust gas temperature sender from

knocks and impact; if dropped, the exhaust gas temperature
sender can no longer be used.
♦ Coat thread with high-temperature paste; for high-temperature
paste refer to ⇒ Electronic parts catalogue .
– Align exhaust gas temperature sender 1 - G235- with as much

clearance from surrounding components as possible.
– Install emission control module ⇒ 6-cylinder TDI engine, 3.0
ltr. 4-valve common rail; Rep. gr. 26 ; Emission control system;
Removing and installing emission control module .
Tightening torques
♦ ⇒ “4.1 Exploded view - exhaust gas temperature control”, page
304

Removing
WARNING

system ⇒ page 3 .

Note


Installing
Note
Take care to protect exhaust gas temperature sender from knocks

and impact; if dropped, the exhaust gas temperature sender can
no longer be used.
– Move exhaust gas temperature sender 2 - G448- into correct

installation position.
• Angle -α- = max. 5°
Tightening torques
304


Removing
WARNING

system ⇒ page 3 .
Note


Installing
Note


– Move exhaust gas temperature sender 3 - G495- into correct

installation position.
• Angle -α- = max. 5°
Tightening torques
304

Removing
WARNING

system ⇒ page 3 .
Note



Installing
Note

– Move exhaust gas temperature sender 4 - G648- into instal‐

lation position, screw in by hand and then tighten from above.
ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust gas temperature
control; Removing and installing exhaust gas temperature sender
4 - G648- .
Tightening torques
304

5 Exhaust gas recirculation

⇒ “5.1 Exploded view - exhaust gas recirculation system”,
page 312
⇒ “5.2 Removing and installing exhaust gas recirculation cooler”,
page 314
⇒ “5.3 Removing and installing exhaust gas recirculation temper‐
ature sensor G98 ”, page 316
⇒ “5.4 Removing and installing pressure sender for exhaust gas
recirculation G691 ”, page 317
5.1 Exploded view - exhaust gas recircula‐

tion system
⇒ “5.1.1 Exploded view - exhaust gas recirculation system, engine
side (front)”, page 312
⇒ “5.1.2 Exploded view - exhaust gas recirculation system, low-
pressure side (rear)”, page 314
5.1.1 Exploded view - exhaust gas recirculation system, engine side (front)
1 - Coolant pipe (top)

19 ; Coolant pipes; Re‐
moving and installing
coolant pipes
2 - Bolt
coolant pipes
3 - O-ring
4 - Bolt
❑ 9 Nm
5 - Banjo bolt
tric compressor
❑ 15 Nm +45°
6 - Seals
tric compressor
7 - Bolt
⇒ page 193
8 - Coolant temperature send‐
er - G62-

9 - O-rings
10 - Vacuum hose
11 - Nut
❑ 5 Nm +90°
12 - Gasket
13 - Exhaust gas recirculation pipe
❑ From turbocharger
14 - Coolant hose
15 - Exhaust gas recirculation temperature sensor - G98-
❑ 35 Nm for aluminium exhaust gas recirculation cooler
❑ 45 Nm for steel exhaust gas recirculation cooler
16 - Exhaust gas recirculation cooler
❑ With exhaust gas recirculation control motor - V338- and exhaust gas recirculation potentiometer -
G212- / exhaust gas recirculation valve 1 - GX5-
❑ Perform adaptions required after renewing a component (using ⇒ Vehicle diagnostic tester)
⇒ “3.8 Performing adaptions after renewing a component”, page 10 .
17 - Coolant hose
18 - Bolt
❑ 9 Nm
19 - Bolt
❑ 9 Nm
20 - Pressure sender for exhaust gas recirculation - G691-
21 - Seal
22 - Pressure pipe
23 - Bolt
❑ 4 Nm
❑ Thread-forming
❑ 3.5 Nm
24 - Gasket
25 - Exhaust gas recirculation pipe
❑ To intake manifold
5. Exhaust gas recirculation 313

26 - Bolt
❑ 9 Nm
5.1.2 Exploded view - exhaust gas recircula‐

tion system, low-pressure side (rear)
4-valve common rail; Rep. gr. 26 ; Exhaust gas recirculation sys‐
tem; Exploded view - exhaust gas recirculation system .
5.2 Removing and installing exhaust gas re‐

circulation cooler
⇒ “5.2.1 Removing and installing exhaust gas recirculation cooler
(front)”, page 314
⇒ “5.2.2 Removing and installing exhaust gas recirculation cooler
(rear)”, page 316
5.2.1 Removing and installing exhaust gas re‐

circulation cooler (front)
Removing
cooling system .

– Remove bolts -arrows- for exhaust gas recirculation pipe.
Vehicles with pressure sender for exhaust gas recirculation -

G691- :
– Remove banjo bolt -1- and bolts -3- and detach wire with pres‐
sure sender for exhaust gas recirculation - G691- .
All vehicles (continued):

– Unplug electrical connectors -1-.
– Unplug electrical connector -2- for coolant temperature sender

- G62- .
– Release hose clip -1- and disconnect coolant hose.

– Pull exhaust gas recirculation cooler (front) -2- slightly up‐

wards off coolant pipe (top).
– Remove bolts -arrows- for coolant pipe (top right) -1-.
– Detach coolant pipe (top right) from thermostat housing and
push to one side.
– Detach exhaust gas recirculation cooler (front).
Installing
Note
♦ Renew seals and O-rings after removal.


page 10 .
Tightening torques
♦ ⇒ “5.1.1 Exploded view - exhaust gas recirculation system,
engine side (front)”, page 312
♦ ⇒ “3.2 Exploded view - reducing agent supply line”,
page 300
♦ ⇒ Fig. ““Turbocharger - tightening torque and sequence”“ ,
page 205
19 ; Coolant pipes; Exploded view - coolant pipes
5.2.2 Removing and installing exhaust gas re‐

circulation cooler (rear)
4-valve common rail; Rep. gr. 26 ; Exhaust gas recirculation; Re‐
moving and installing exhaust gas recirculation cooler .
5.3 Removing and installing exhaust gas re‐

circulation temperature sensor - G98-

♦ Open crow-foot ring spanner, 14 mm (commercially available)

Removing
Exhaust gas recirculation; Removing and installing exhaust gas
recirculation temperature sensor - G98- .
– If necessary, remove bolts -arrows- and detach oil filler neck
-1-.
– Seal off opening with plug from engine bung set - VAS 6122-
(clean plug thoroughly).
WARNING

system ⇒ page 3 .
– Disconnect vacuum hose -1-.

– Use an open crow-foot ring spanner, 14 mm to unscrew ex‐
haust gas recirculation temperature sensor - G98- -item 2-.
Installing
– Align exhaust gas recirculation temperature sensor - G98- with
as much clearance from surrounding components as possible.
ltr. 4-valve common rail; Rep. gr. 26 ; Exhaust gas recirculation;
Removing and installing exhaust gas recirculation temperature
sensor - G98-
Tightening torques
page 312
5.4 Removing and installing pressure send‐

er for exhaust gas recirculation - G691-
Removing

– Unplug electrical connector -arrow- and remove pressure

sender for exhaust gas recirculation - G691- .
Installing
Note
Renew seal after removing.
Tightening torques
page 312

6 Exhaust manifold
⇒ “6.1 Exploded view - exhaust manifold”, page 319
⇒ “6.2 Removing and installing exhaust manifold”, page 319
6.1 Exploded view - exhaust manifold
WARNING

system ⇒ page 3 .
1 - Nut
❑ Coat thread with high-
temperature paste; for
high-temperature paste
refer to ⇒ Electronic
parts catalogue
❑ 25 Nm
2 - Exhaust manifold
2 (left-side)
26 ; Exhaust manifolds;
Removing and installing
exhaust manifolds
3 - Gasket
4 - Seal
5 - Clamp
❑ Tightening torque of bolt
6.2 Removing and installing exhaust mani‐

fold
4-valve common rail; Rep. gr. 26 ; Exhaust manifolds; Removing
and installing exhaust manifolds .
6. Exhaust manifold 319

28 – Glow plug system

1 Glow plug system
⇒ “1.1 Exploded view - glow plug system”, page 320
⇒ “1.2 Removing and installing glow plug”, page 322
⇒ “1.3 Removing and installing automatic glow period control unit
J179 ”, page 325
⇒ “1.4 Removing and installing Hall sender G40 ”, page 326
⇒ “1.5 Removing and installing engine speed sender G28 ”, page
326
1.1 Exploded view - glow plug system
1 - Sender wheel
er - G28-
⇒ page 37
2 - Glow plug
❑ Cylinder bank 1 (right-
side):
♦ Glow plug 1 - Q10-
♦ Country-specific version:
Glow plug 2 - Q11- with cyl‐
inder 2 combustion cham‐
ber pressure sender -
G678-
❑ Cylinder bank 2 (left-
side):
⇒ page 322
❑ Glow plug versions
⇒ page 321
3 - Bolt
❑ Thread-forming
hand so that it is
que
❑ 5.5 Nm
4 - Bracket
5 - Bolt
❑ Thread-forming
320 Rep. gr.28 - Glow plug system

❑ 5.5 Nm
6 - Automatic glow period control unit - J179-
❑ Illustration shows version 1
❑ Version 2 ⇒ page 322
♦ ⇒ “1.3.1 Removing and installing automatic glow period control unit J179 - version 1”, page 325
♦ ⇒ “1.3.2 Removing and installing automatic glow period control unit J179 - version 2”, page 325
7 - Bracket
8 - Bolt
❑ 9 Nm
9 - Bolt
❑ 9 Nm
❑ Thread-forming
❑ 5 Nm
10 - Hall sender - G40-
11 - O-ring
12 - Engine speed sender - G28-
13 - Bolt
❑ 9 Nm
Glow plug versions and tightening torques

1 - Glow plug with combustion chamber pressure sender
♦ Only fitted on cylinder 2 on some versions; glow plug 2 - Q11-
with cylinder 2 combustion chamber pressure sender - G678- ;
allocation ⇒ Current flow diagrams, Electrical fault finding and
Fitting locations
♦ 12 Nm
2 - Glow plug without combustion chamber pressure sender
♦ 12 Nm
1. Glow plug system 321

Automatic glow period control unit - J179- - version 2

Removing and installing
⇒ “1.3.2 Removing and installing automatic glow period control
unit J179 - version 2”, page 325
2 - Bolt, 4.5 Nm
1.2 Removing and installing glow plug

♦ Articulated wrench, 10 mm - 3220-
♦ Socket insert AF 12 for glow plugs 4-cyl. TDI CR diesel - VAS

6454-
Removing
Caution
Incorrect handling of ceramic glow plugs can cause engine

damage.
– Unplug electrical connectors on glow plugs.

– Clean glow plug opening to make sure no dirt gets into cylin‐
ders; note the following:

WARNING
Risk of eye injury.

♦ Use a vacuum cleaner to remove coarse dirt.

♦ Spray brake cleaner or suitable cleaning agent into glow plug
apertures, let it work in briefly, and blow out with compressed
air.
♦ Clean glow plug opening with an oily cloth.
Releasing glow plugs without combustion chamber pressure
sender
With T-bar and socket, 10 mm - 3220-
Releasing glow plugs with combustion chamber pressure sender
Note
♦ The glow plugs can only be released up to an angle of approx.

90°. After this, the turning movement is hindered in part by a
tendency to seize.
♦ This tendency to seize is caused by particles of dirt (e.g. sand)
entering the first glow plug threads as heat causes the glow
plugs (steel) and the cylinder head (aluminium) to expand.
– Unscrew glow plug until it begins to stick, then screw it in again.

After this, unscrew it again until it begins to stick.
• Keep turning the glow plug back and forth up to the point where
it begins to stick. Repeat this procedure until the glow plug can
be removed.

– Pull out glow plugs carefully by hand or using a suitable hose,

as shown in illustration. Keep glow plugs straight while un‐
screwing.
Installing
Note
Due to the special properties of the material used, ceramic glow

plugs are easily damaged and require extra care when installing.
– Screw in glow plugs carefully by hand or using a suitable hose,

as shown in illustration. Keep glow plugs straight while un‐
screwing.
– Ensure that electrical connectors are securely seated.
Tightening torques
♦ ⇒ Fig. ““Glow plug versions and tightening torques”“ ,
page 321

1.3 Removing and installing automatic glow

period control unit - J179-
1.3.1 Removing and installing automatic glow

period control unit - J179- - version 1
Removing
– Unscrew bolts -arrows- and detach automatic glow period
control unit - J179- together with bracket.
– Unscrew bolts -arrows- and detach automatic glow period

control unit - J179- -item 1- from bracket -2-.
Installing
Tightening torques
♦ ⇒ “1.1 Exploded view - glow plug system”, page 320
1.3.2 Removing and installing automatic glow

period control unit - J179- - version 2
Removing
– Pull off seal and lift plenum chamber cover slightly.
– Remove bolt -arrow-.
– Unplug electrical connector -1- and detach automatic glow pe‐
riod control unit - J179- .
Installing
Installation is carried out in reverse sequence.
Tightening torques
♦ ⇒ Fig. ““ Automatic glow period control unit -J179- - version
2”“ , page 322

1.4 Removing and installing Hall sender -

G40-
Removing
Glow plug system; Removing and installing Hall sender - G40- .
– Unscrew bolt -1- and remove Hall sender - G40- .
Installing
Note

Tightening torques
1.5 Removing and installing engine speed

sender - G28-
Removing
– Remove noise insulation (rear)/one-piece noise insulation ⇒
– Unscrew bolt -1- and detach engine speed sender - G28- .
Installing
Installation is carried out in reverse sequence.
Tightening torques

Engine Tdi 6 Cyl Ea897 Gen2 Service Manual Eng

Uploaded by

Copyright:

Available Formats

Engine Tdi 6 Cyl Ea897 Gen2 Service Manual Eng

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Engine Tdi 6 Cyl Ea897 Gen2 Service Manual Eng

Uploaded by

Copyright:

Available Formats

Service

Service Department. Technical Information

10 - Removing and installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Removing and installing balance shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

15 - Cylinder head, valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

3.2 Removing and installing oil separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

23 - Mixture preparation - injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

4.3 Removing and installing intake manifold (bottom section) . . . . . . . . . . . . . . . . . . . . . . . . . . 232

26 - Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

4.1 Exploded view - exhaust gas temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

28 - Glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

1.1 Engine number/engine data

2.1 Safety precautions when working on the fuel system

Risk of fire due to escaping fuel

2.2 Safety precautions when working on vehicles with start/stop system

2 Rep. gr.00 - Technical data

2.4 Safety precautions when working on the cooling system

2.5 Safety precautions when working on the exhaust system

Risk of injury caused by components of the exhaust system

Risk of poisoning due to chemical substances

Risk of injury due to hot condensation and particles in exhaust

2.6 Safety precautions when working on the SCR system

Risk of damage caused by reducing agent

When removing and installing components at the SCR system,

4 Rep. gr.00 - Technical data

Automatic drawing back of reducing agent

2.7 Safety precautions when working on the

♦ Due to the special properties of the material used, ceramic

2.8 Safety precautions when working on the subframe

– Never support weight of vehicle on subframe or subframe

6 Rep. gr.00 - Technical data

3.1 Rules for cleanliness

3.2 General notes

♦ Wait for 60 seconds each time after performing final control

3.3 General repair instructions

The high-pressure pump has very close tolerances and must

♦ Clean tools and workbench etc. before working on the injection

8 Rep. gr.00 - Technical data

♦ Check all new O-rings for damage before installing. Lubricate

3.4 Foreign particles in engine

3.5 Contact corrosion

3.6 Routing and attachment of pipes, hoses

3.7 Installing radiators and condensers

3.8 Performing adaptions after renewing a

10 Rep. gr.00 - Technical data

♦ 0001 - Engine electronics, functions

♦ 00AC - Control unit for reducing agent metering

♦ 00AC - Replace control unit for reducing agent me-

10 – Removing and installing engine

12 Rep. gr.10 - Removing and installing engine

3 Engine cover panel

3.1 Removing and installing engine cover

14 Rep. gr.10 - Removing and installing engine

1.1 Exploded view - cylinder block (pulley

1. Cylinder block (pulley end) 15

16 Rep. gr.13 - Crankshaft group

Bracket for alternator -1- - tightening torque and sequence

1. Cylinder block (pulley end) 17

Routing of poly V-belt

18 Rep. gr.13 - Crankshaft group