Scribd
Upload
28 views1 page

Valleylab Force4b Spec. Sheet

This document provides specifications for the VALLEYLAB® FORCE 4B® high power digital electrosurgical unit. It can be used for almost any electrosurgical procedure and offers both monopolar and bipolar output. The document lists detailed technical specifications for the device including dimensions, weight, input power source, output characteristics, output waveform, and leakage parameters.

Uploaded by

Mariam Mostafa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
28 views1 page

Valleylab Force4b Spec. Sheet

This document provides specifications for the VALLEYLAB® FORCE 4B® high power digital electrosurgical unit. It can be used for almost any electrosurgical procedure and offers both monopolar and bipolar output. The document lists detailed technical specifications for the device including dimensions, weight, input power source, output characteristics, output waveform, and leakage parameters.

Uploaded by

Mariam Mostafa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

VALLEYLAB® FORCE 4B®

• High Power Digital Electrosurgical


Unit.
• This unit has digital display for
output power and can be used for
almost any electrosurgical procedure.
• Offers both Monopolar and bipolar
output.
Typical Manufacturer’s Picture

Specifications
Dimensions: 6 x 13 x 22 inches (15 x 33 x 56 cm)
Weight: 25 lbs. (11.4 kg)
Input Power Source: Nominal input line voltage is 120 VAC with a full range of 95-140 VAC. Frequency line varies
from 45 to 64 Hz
Max. Current Max. Power
Idle 0.4 A 50 W
Cut 5.0 A 700 W
Coag 3.0 A 300 W
Bipolar 1.5 A 180 W
Output Characteristics Max. P-P Voltage Rated Load (ohms) Nominal Power (watts) Crest Factor
Cut 5000 300 300 1.9 @ 100 W
Blend 1 5800 300 250 3.0 @ 100 W
Blend 2 5800 300 200 3.8 @ 100 W
Blend 3 6500 300 200 6.0 @ 100 W
Spray Coag 9000 300 120 10.0 @ 50 W
Soft Coag 900 300 60 12 .0@ 50 W
Low Volt Coag 6500 300 99 6.0 @ 50 W
Std Bipolar 1800 100 70 5.5 @ 40 W
Precise bipolar 600 100 70 2.2 @ 40 W
Output Waveform Sinusoid Duty Cycle Recurrence
Cut 750 kHz -------------- ---------------
Blend 1 750 kHz bursts 50% 31 kHz
Blend 2 750 kHz bursts 31% 31 kHz
Blend 3 750 kHz bursts 27% 31 kHz + inductive discharge damped sinusoidal bursts
Spray Coag 750 kHz _________ 31 kHz
Soft Coag 750 kHz _________ 20.7 kHz
Low Voltage Coag 750 kHz bursts 27% 31 kHz + inductive discharge damped sinusoidal bursts
Std Bipolar 750 kHz 25% 31 kHz
Precise Bipolar 750 kHz _________ _________
Low Frequency Leakage: (50/60 Hz) Normal polarity: intact chassis ground - <10 mA, ground open - <100 mA. Reverse
polarity: ground open - <100 mA. Sink current, 140V applied, all inputs - <150 mA. Chassis source
current, ground open - <110 mA
High Frequency risk parameters: Bipolar RF leakage current: <150 milliamperes
REM™ Contact Quality Monitor: Measurement frequency: 140 kHz ± 10 kHz. Measurement current: 1.0 mA ± 0.5 mA

Soma Technology, Inc. acknowledges all registered trademarks of manufactures’ listed.


The technical data given in this publication are for general information and is subject to change
without notice.

166 Highland Park Dr. Bloomfield, CT 06002 U.S.A.


Tel: (860) 218-2575 Fax: (860) 218-2565 Email: [email protected]
Rev 1 1/03

You might also like