Scribd
Upload
21 views11 pages

Flash60 EN

This document provides instructions for uploading languages or software to a DNC 60 controller using the Flash60 software. Flash60 operates differently depending on whether it is used from a CD or from a PC. When used from a CD, only one software version is available, while using it from a PC allows selecting different versions or an advanced mode. The uploading process involves connecting the DNC and PC with an RS-232 cable, pressing keys to put the DNC in flash mode, selecting the desired languages or software, and uploading them. Possible issues like connection errors or no displayed languages are also addressed.

Uploaded by

solutionbriigh1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
21 views11 pages

Flash60 EN

This document provides instructions for uploading languages or software to a DNC 60 controller using the Flash60 software. Flash60 operates differently depending on whether it is used from a CD or from a PC. When used from a CD, only one software version is available, while using it from a PC allows selecting different versions or an advanced mode. The uploading process involves connecting the DNC and PC with an RS-232 cable, pressing keys to put the DNC in flash mode, selecting the desired languages or software, and uploading them. Possible issues like connection errors or no displayed languages are also addressed.

Uploaded by

solutionbriigh1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

Flash60

User guide

CYBELEC SA Tel. ++ 41 24 447 02 00


RUE DES UTTINS 27 Fax ++ 41 24 447 02 01
CH - 1400 YVERDON-LES-BAINS E-Mail: [email protected]
SWITZERLAND
PAGE 1 SUPPORT TOLE DNC 60 GCUT
This page has been left blank intentionally.
March 9, 2007 V. 1.2

TABLE OF CONTENTS
General................................................................................................................................3
Uploading languages or a software.....................................................................................3
Flash60 on CD.....................................................................................................................4
Flash60 on PC.....................................................................................................................6
Select an other version 6
Flash60 Advanced 7
RS232 configuration ............................................................................................................8
Problems .............................................................................................................................9
Can’t connect 9
No displayed language 9

FLASH60_EN.DOC TABLE OF CONTENTS PAGE I


This page has been left blank intentionally.

PAGE II USER GUIDE FLASH60


GENERAL
This Flash60 version 2 has been developed for a one-step upload operation of
a choice of languages into the DNC.
The manufacturer has the possibility to select and upload several languages
as per his needs until the very last moment.

Flash60 works differently on CD and PC:


• On CD:
Flash60 offers the easiest interface, with the only software version
available on the CD.
• On PC:
Flash60 provides simple or advanced method with several software
versions.

UPLOADING LANGUAGES OR A SOFTWARE


• Make sure the DNC is OFF.
• Connect the DNC via a RS232 (null modem) cable (see chapter
Problems for a cable drawing).

• Press simultaneously the and manual buttons and keep


them pressed while switching ON the DNC.
• The flash page transfer is shown on the DNC.
• Make sure the DNC is not in STOP.

USER GUIDE FLASH60 PAGE 3


FLASH60 ON CD
Flash60 on CD can use just one software version that is with each CD
delivered with a DNC. This software version needs to be in the same
directory as Flash60.
• Run Flash60.

Flash60 try to connect automatically to the DNC and to recognize


the model.

If Unknown DNC connected is displayed, you need to copy


Flash60 on the PC so you can use some additional functionality.
The DNC can not give the information about its hardware type;
there is older boot software.

CheckSum number

When the model is recognized, the available languages are displayed


in the left-hand column.
The software selected by Flash60 is the first found and
corresponding to the connected hardware in the same directory as
the Flash60 software.
• Select the different languages.
• Press the Upload button to load the languages into the DNC.
• Wait until the transfer is terminated

PAGE 4 USER GUIDE FLASH60


• Verify that the DNC provide you a checksum number identical as
shown in the Flash60 windows. (If KO is shown, restart the
procedure).
• Switch OFF the DNC
• If you uploaded the DNC with same software, your data are still
valid.
• If not please clear memory with the “817” procedure (see the User
guide of the DNC, chapter Maintenance).

USER GUIDE FLASH60 PAGE 5


FLASH60 ON PC
In Flash 60 on PC, there are two additional functionalities:
• Other version
This functionality allows to browse the software version.
• Advanced
This functionality allows to use all possibility of Flash60 as load a
boot, N2X or DNC software.
Run Flash60 and follow the procedure as in chapter Flash60 on CD.

Select an other version

By clicking on the Other version button, it is possible to select another


software.

Hardware type filter

Only the compatible softwares with the detected hardware are displayed. This
limitation can not be changed without passing by Flash60 Advanced.

PAGE 6 USER GUIDE FLASH60


Flash60 Advanced

By clicking on the Advanced button, Flash60 Advanced opens.

In the Flash60 Advanced, it is possible to load a DNC, N2X or boot software.


By selecting Select File DNL, the filter selector is free.

Hardware type filter

USER GUIDE FLASH60 PAGE 7


RS232 CONFIGURATION
The RS232 parameters must be the same on DNC and computer. By default,
the configuration is identical.

By clicking on the button above, it is possible to modify the parameters of the


RS232 connexion.
Default configuration of the PC:

Default configuration of the DNC:

FLASH PROGRAMMING SOFTWARE


DNC 60 BOOTDNC: ZIAMBB0.
BOOTN4X: ZZAMBA7.

- CONNECT J5 TO A PC

- TRANSMISSION PARAMETERS:
38400 BDS, 8 BITS, PARITY ODD, 1 STOP

- ++ KEY CHANGES THE BAUDRATE


- -- KEY RUNS THE TRANSMISSION TEST OF
THE SERIAL PORT IN MODE ECHO

STATUS: WAITING
MESSAGE:
CHECKSUM:

PAGE 8 USER GUIDE FLASH60


PROBLEMS

CAN’T CONNECT

If you are using Flash60 and you have always the screen below.

There is some different possibility to your problem:


• The DNC stop is activated.
The led of the Stop key is on, press the Stop key.
• The DNC is not on the FLASH TRANSFER page.

Switch off the DNC and switch on while the and keys
are pressed.
• There is not the same RS232 configuration on the DNC and on the
PC.
Check what you have in the DNC and put the same in the PC. (See
the RS232 configuration chapter.
• The cable is not connected to the PC or the DNC.
The cable is not crossed (see the drawing below) or interrupted.

NO DISPLAYED LANGUAGE

If no language is displayed in the left column, this can come from one factor:
• No selected software.
The CD doesn’t correspond to the DNC model.
No software corresponding to the DNC is founding in the current
directory on a PC.

USER GUIDE FLASH60 PAGE 9

You might also like