— BNakamichi’ [email protected] User Manual CLASS-D MONO BLOCK POWER AMPLIFIER Mm nakamichicaraudio.com i nakamichi.global nakamichi.caraudioINTRODUCTION Thank you for your purchase of our Nakamichi product and we warmly welcome you to the Nakamichi family! Do keep your original invoice and purchase receipt in a safe place in case of future service and warranty claims. You may also contact your appointed Nakamichi service agent for any future technical support requirements. ACCESSORY LIST 1. User Manual 2pes 2. Amplifier Ipe 3. Mounting Screw(4x20mm) 4pes 4, Mounting Bracket Screw(4xémm) Apes 5. Remote Control Iset 6 Fixing frame (34x20mm) Ipes 7.L-type wrench(L=90mm) Ipes SPECIFIATIONS N-power Output@4Q 400Wx1 N-power Output@20 600Wx! Max Output Power 3600W Full Frequency Response 5Hz-20KHz SUB Frequency Response 30-250Hz Signal To Noise Ratio +N 29008 Sensitivity 0.32V-6.5V Unit Dimensions(LxHxW) 195x120x48mm Net Weight Approx. 1.3kg Box Dimensions(LxHxW) 265x218x75mM Gross Weight Approx. 2.4kg Allspecifications subject fo change without notice, TENDIMENSIONS (UNIT:MM) WwW ' O ©} YONeakamichi ee@ iit iit Ex-Y-r-) 2ENPOWER CONNECTION LEADS BATTERY Notes on the power supply Connect the +12V power input lead only after all other leads have been connected. Be sure to connect the ground wire of the unit securely to a meatal part of the car. A lose connection may cause a malfunction of the amplifier. REMOTE: The unit is turned on by applying +12Volts to this terminal. This terminal does not draw heavy current like the two power terminal so a thinner connecting wire is acceptable. Standard 18 GAUGE is fine and the standard colour is yellow. If the radio is equipped with a power antenna control wire, it can drive this terminal. If the power antenna wire is already in use, you can still splice into if. With this method, the unit will turn on automatically with the radio. 3ENPOWER CONNECTION LEADS Use the power supply lead with a fuse attached whose value is the same as original fuse. Place the fuse in power supply lead as close as possible to the car battery. During a full power operation, Maximum current will run through the system. Therefore. Make sure the that the leads to be connected to the +12V and GND terminals of the unit respectively must be larger than 8-Gauge(AWG.8). CONNECTION 1: 1-SPEAKER MODE 2-49 E SPEAKER oO _ OO0O0 Pee oo Qu 5S GY © Ss 4ENPANEL CONTROLS AND FEATURES YONekamichi Oo° Leper Quo JKL MON "66606 TT TT A. ROMOTE LEVEL CONTROL INPUT DEFGH Attached the included remote level control here to cantrol the volume level to the subwoofer independently. B.LOW LEVEL RCA INPUT These RCA input jacks connect with your source unit RCA low level outputs or via optional adapter with your source unit speaker high level outputs. The use of high quality twisted pair car audio cables is recommended to reduce the possibilty of audio signal degration. C. POWER AND PROTECTION INDICATOR The protection red LED will light up , if there is a fault present in the amplifier. Please disconnect the amplifier and resolve the foult before reconnecting the amplifier. The power indicator green LED will light up when the amplifier is working correctly. D. SPEAKER CROSSOVER CONTROL Depending on the selected switch the amplfier will operate at full or sub mode. SENPANEL CONTROLS AND FEATURES E. SPEAKER GAIN CONTROL The gain control will match the amplifiers sensitivity to the source signal voltage. F. BASS BOOST The BASS BOOST feature will increase the sound level in the bass frequencies. G. SPEAKER LOW PASS CROSSOVER FREQUENCY Controls low frequency of the amplifier between 30Hz to 250Hz. H. SUBSONIC FILTER CONTROL. This control allows you to filter out unwanted low frequencies from 15Hz to 60Hz, this allows you to increase the power handing of your installed woofers |, PHASE Controls phase of the amplifier between O°to 180°. J. GND(-) = GROUND CONNECTION Connect this coble directly fo the metal frame of the vehicle, ensuring that the metal frame has been strpped of all paint down to the bare metal. Use the shortest distance possible. It is atways a good idea to replace the vehicle battery groudn terminal or any other factory ground points. K. REM(ON/OFF) REMOTE CONTROL When using low level inputs, the amplifier REM-IN should be connected to the REM-OUT of the source unit. The source unit will control the amplifier to automatically turn on or off. L. +12V = POWER SUPPLY Connect this terminal through a fuse or circuit beraker to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery. M. FUSE Do not use a fuse with a different value and NEVER replace the fuse with a wire or coin. N. SPEAKER CONNECTIONS Connect your speakers and woofers to there terminals, ensuring proper polarity during connection. Never connect the speaker cables to the chassis ground. 6 ENINTERFERENCE All cables can create interference. The power cable and cinch / RCA audio cables are very prone to interference from other sources, while remote cables are less prone. Interference is often caused by the generator, ignition, or any other electronic parts or systems. Most of these problems can be eliminated by correct and careful wiring during setup. Here are some guidelines to follow. + Use only a shielded audio cable for the wiring between the low level input of the amplifier and the RCA or DIN output of the radio. * Lay the signal, speaker and power cables separately with enough distance from one another and also from each other car cable. Irnot possible, you can lay the circuit and ground cable together with the serial cables. Audio and speaker cable should be as far away from these as possible. The REM cable to the automatic antenna output of the radio can be laid together with the signal cables. * Avoid ground loops by laying the ground wiring of all components towards a central point in a star layout. You can locate fne best point by measuring the voltage directly at the battery, and comparing the voltage value with the chosen ground point and the positive terminal of the amplifier. If the measured voltage is only slightly different, you've found the correct central location. Other wise please look for another point. You should measure with the ignition point for earth switched on. * If there are pickups from external electrical sources into the speaker cables, divide the core leads and twist them together. * If there are noises from the car electrics, add an interference suppression choke into the power wiring. * If there are humming noises, use thicker ground cables or add further ground cables to the chassis. * To reduce contact resistance and bad and loose contacts, please solder the cable ends or use multi core cable ends, spade terminals or others. Gold Plated spade terminal are free of corrosion and have the lowest contact resistance. + Should all these measures not bring about any success, the use of a ground loop isolator may solve the problem 7ENTROUBLESHOOTING If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages.|f problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE CAUSE ACTION TO TAKE “Low or no temole tum-on put “Check remote furn-on vollage output at amplifier and correct os needed so blown shack power wire ivearly and reversed polarly, repor 0s needed and replace fuse NoouPuY [a acomonioa Reset crossovers refering fo Tne mulitcro crossover speaker configuration section of ths manual DISTORTED speaker we blown “Check system with known working speaker and repor OUTPUT (CONT'D) orreplace as needed -Speaker wed wrong polaily “Check speaker poloriy and repair os needed Roser POOR BASS cancellation at low frequencies crossovers refering o the mul-cross RESPONSE ~Cosover set neon “Crossover configuration secrion of this manual for Crossovers cly detaled instructions “Check speaker impedance load, below 20) eres -Impedance load to amplifier too low | or 4 mono rewire speaker to achieve a higher impedance “Shor in power whe or icoect power [-Check power ond Ground connections and repair as pistoeteo connections needed OUTPUT “Fuse used's smaller than Replace with proper fuse size (CONT'D) recommenced “Check speaker impedance loads I below 2a stereo s1oo much cunent being drawn or 40 mono rewire speaker fo achieve a higher impedance “ron inpawer ka ofineonsh “Check power and ground connections and repo Gr needed BENSCAN OUR QR CODE OR VISIT WWW.NAKAMICHICARAUDIO.COM FOR COMPLETE AUDIO SETTINGS INSTRUCTIONS Gi nakamichi.global Made in China nakamichi.caraudio