Scribd
Upload
59 views4 pages

Corbel Design

The document provides details for designing a corbel to support a load of 3930 kN. It determines the corbel geometry, evaluates the forces, checks the shear capacity, and checks the bearing stress inside the bend. The corbel dimensions are determined to be 1100 mm height, 1200 mm at the column face, and 1154 mm depth to satisfy shear and bearing stress requirements. Reinforcement of 11T32 bars is selected, providing 8846.72 mm^2 area to resist the required 8298.69 mm^2. Shear link reinforcement of 4 legs of T12 bar at 100 mm spacing is also required.

Uploaded by

Tan Choon Leng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
59 views4 pages

Corbel Design

The document provides details for designing a corbel to support a load of 3930 kN. It determines the corbel geometry, evaluates the forces, checks the shear capacity, and checks the bearing stress inside the bend. The corbel dimensions are determined to be 1100 mm height, 1200 mm at the column face, and 1154 mm depth to satisfy shear and bearing stress requirements. Reinforcement of 11T32 bars is selected, providing 8846.72 mm^2 area to resist the required 8298.69 mm^2. Shear link reinforcement of 4 legs of T12 bar at 100 mm spacing is also required.

Uploaded by

Tan Choon Leng
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

Job No :

Title :

Corbel Design

(1) Input data


T= 80 KN
3930 V= 3930 KN
Column Size = 700 x 700
650 30 fcu = 35 N/mm2
fy = 460 N/mm2
Cover = 30 mm
1200 av = 650 mm
1200 Corbel Width = 700 mm
400 Bearing Plate 300 mm
1100 Length
Bearing Plate 400 mm
700 Width

(2) Determination Of Corbel Geometry

Maximum Bearing Stress = 0.8 x fcu = 28 N/mm2

Minimum Bearing Width, lw = V


0.8fcu x Bearing Plate Length

= 467.86 mm > 400 NG

Length of Corbel, l = av + lw/2 + Length of bend of bar + min. Cover + Link dia. + min Cover
.= 1060 mm
So, Use h = 1100 mm
h at Column face 1200 mm

d= 1154 mm

Maximum allowable shear stress st column face = 5 N/mm2


d> V
5b
> 1122.857143 mm

So, v = V
bd
= 4.87 N/mm2 < 5.0, OK
(3) Evaluation Of Force

Ft = FcCosb + T = Vav + T
z
Fc = ( 0.67fcu ) b (0.9xCosb ) = 0.402 fcubxCosb
1.5

V = Fc Sin b
z = d - 0.45x

Find x value by Iteration,

Assume x to be 0.4d, x = 813 mm

z= 788.15 mm
Cot b = av = 0.82
z
So , b = 50.4870

Sin b = 0.77
Cos b = 0.64

Fc = V = 5094.10 KN
Sin b

x= Fc = 812.92 mm
0.402fcubCosb OK

Final z = 788.15 mm

Ft = Vav + T = 3321.13 KN
z

As req = Ft = 8298.69 mm2


0.87fy

0.5V + T = 5109.95 mm2 < As req


0.87fy 0.87fy

Provide 11 T 32
As Prov = 8846.72 mm2

(3) Check Shear

100As = 1.10
bd
vc = 0.73 N/mm2

vc' = (2d) x vc
av

= 2.59 N/mm2 < v, Shear Link is required

Asv = b (v-vc)
Sv 0.87fyv

= 3.98 Say, use 4 leg of T 12 Link


Sv = 100 mm

So, 2/3 of "d" use T10 - 100

(4) Check Bearing Stress Inside Bend (Fbt)

Fbt = ( Ft ) x As req
no. of bars As prov

= 283.22 KN

Ultimate anchorage bond stress, fbu = 0.5 fcu ( from Table 3.28 of BS 8110:Part 1)
= 2.96

Anchorage bond length required Fbt


pffbu
= 952.39 mm

You might also like