HiPath 4000 V6 - Section 4 - IP Solutions - Service Documentation - Issue 8

HiPath 4000 V6 
IP Solutions
Service Documentation
A31003-H3160-S104-8-7620
Our Quality and Environmental Management Systems are
implemented according to the requirements of the ISO9001 and
ISO14001 standards and are certified by an external certification
company.

Copyright © Unify GmbH & Co. KG 07/2014 
Hofmannstr. 51, 81379 Munich/Germany
All rights reserved.
Reference No.: A31003-H3160-S104-8-7620
The information provided in this document contains merely general descriptions or
characteristics of performance which in case of actual use do not always apply as 
described or which may change as a result of further development of the products. 
An obligation to provide the respective characteristics shall only exist if expressly agreed in
the terms of contract.
Availability and technical specifications are subject to change without notice.
Unify, OpenScape, OpenStage and HiPath are registered trademarks of Unify GmbH & Co. KG.
All other company, brand, product and service names are trademarks or registered trademarks
of their respective holders.
unify.com
HiPath 4000 V6 - IP Solutions - Contents
Highlights and Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Gateways HG 3500 and HG 3575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1 Goal of this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.1 Key Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.2 Fax or Modem Transmission and Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.3 Codec Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.4 Voice Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.5 Jitter Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.5.1 Jitter Buffer Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.5.2 Jitter Buffer Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5.3 Considerations when Configuring the Delay for Static Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.5.4 Clock Drift with Static Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2.5.5 Minimum Delay for Adaptive Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.5.6 Packet Loss Control in Adaptive Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.5.7 Parameters for Jitter Buffer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.6 Runtime and Noticeable Effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.6.1 General Information on Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.6.2 Delay and Echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.6.3 Delay and Hands-Free Talking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
2.7 Voice Encryption Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3 Architecture and System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.3 Network Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.4 Network Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.4.1 TOS Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.5 Bandwidth Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.5.1 Encoding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.5.2 Sampling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.5.3 IP Overhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3.5.4 Required Bandwidth per Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3.5.5 Voice Activity Detection (VAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.5.6 DMC Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.6 B Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3.6.1 B Channel Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.6.1.1 AMO BFDAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.6.1.2 AMO BCSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.6.2 Automatic b channel reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.6.3 Displaying the B Channels currently Available/Configured (possible IP-Based Connections) . . . . . . . 66
3.7 Traffic Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4 Supported Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.1 HG 3500 (Common Gateway) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.1.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.1.2 Board Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
A31003-H3160-S104-8-7620, 07/2014
HiPath 4000 V6, IP Solutions, Service Documentation 3
4.1.3 Feature Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

4.1.4 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.2 HG 3575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4.2.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4.2.2 Exchanging Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5 Features and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.1 Direct Media Connection (DMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.2 Voice Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.3 Voice Activity Detection (VAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.4 Comfort Noise Generation (CNG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.5 Echo Cancellation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
5.6 Redundant LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7.1 Access for Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7.2 Access to SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7.3 Security in CorNetTC Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7.4 H.235 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.7.5 Connecting IP Gateways to the Internet or via External Providers . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5.8 Resource Manager (RM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5.9 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.9.1 Loadware-Update or Reset of the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.9.2 Possible IP hops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
6 Communication Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
7 Load Concept for Gateway Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.2 Notes on IP Gateway Loadware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.3 Load Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
7.4 Updating Loadware with Web-Based Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
7.5 Updating Loadware with "LW Update Manager" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
7.6 General Comments on Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
8 Save Configuration Data in Local Flash ((local Backup & Restore) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
8.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
8.2 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
8.3 Startup Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
8.4 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
8.5 Special Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
9 Loadability of the FPGA on the STMI4/NCUI4 board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
10 Standby Board HG 3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
10.1 Feature Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
10.2 User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
10.3 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
10.4 Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
10.5 Service steps after the automatic switch over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
10.6 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
11 DLS Client Bootstrapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
11.1 Bootstrapping with "No PIN" PIN Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
11.2 Bootstrapping with "Default PIN" or "Individual PIN" PIN Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
A31003-H3160-S104-8-7620, 07/2014
4 HiPath 4000 V6, IP Solutions, Service Documentation
12 Gateway HG 3575 - Changing Parameters with AMO STMIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

12.1 TYPE GLOBAL - Changing the Idle Bit Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
12.2 TYPE IFDATA - Changing the Interface-Specific Parameters of the Access Point . . . . . . . . . . . . . . . . . 126
12.3 TYPE SERVIF - Changing the Login and Password for Service Access. . . . . . . . . . . . . . . . . . . . . . . . . 128
12.4 TYPE ASC - Changing the Payload QoS Setting of the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . 129
12.5 TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size, Voice Activity Detection and
T.38 Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
12.6 TYP ASC - Transmission of DTMF/Fax/Modem Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
12.7 TYPE DSP - Jitter Buffer Size of the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
12.8 TYPE DMCDATA - Changing the Access Point Setting to Support Direct Media Connections. . . . . . . . 131
12.9 TYPE H323 - Changing the H323 Settings at the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
12.10 TYPE JB - Configuring the Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
12.11 TYPE SIGQOS - Quality Monitoring for the Signaling Connection over IP . . . . . . . . . . . . . . . . . . . . . . 133
12.12 TYPE SNMP - Changing the Community Strings for Read Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
12.13 TYPE MGNTDATA - Management Data and Backup Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
12.14 TYPE WBMDATA - Changing the Login and Password for WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
12.15 TYPE GWSECTOR - Changing the Access Point Sector Number for the Resource Manager . . . . . . . 136
12.16 TYPE DLSDATA - Configuring DLS Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
12.17 TYPE SOCODATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
12.18 TYPE IPCONF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
12.19 Resetting the Parameters to Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
13 General Information on How to Configure a HG 3500 Common Gateway. . . . . . . . . . . . . . . . . . . . . . 139
13.1 Changing the common gateway configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.2 AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.3 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.4 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
13.5 Overview of Configuration Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
14 Gateway HG 3500 - Changing Parameters with AMO CGWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
14.1 TYPE ASC - Changing the Payload QoS Setting in Host System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
14.2 TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size, and Voice Activity Detection
144
14.3 TYP ASC - Transmission of DTMF/Fax/Modem Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
14.4 TYPE DMCDATA - Changing the HG 3500 Setting to Support Direct Media Connections . . . . . . . . . . . 145
14.5 TYPE DSP - Changing the DSP (Signal Processor) Setting at an HG 3500 . . . . . . . . . . . . . . . . . . . . . . 146
14.6 TYPE GLOBIF - Changing the Idle Bit Pattern and Interface-Specific Parameters . . . . . . . . . . . . . . . . . 146
14.7 TYPE GWSECTOR - Changing the HG 3500 Sector Number for the Resource Manager . . . . . . . . . . . 147
14.8 TYPE H235DATA - H.235-Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
14.9 TYP MGNTDATA - Connection to the HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
14.10 TYPE SERVIF - Changing the Login and Password for the Service Access. . . . . . . . . . . . . . . . . . . . . 149
14.11 TYPE WBMDATA - Changing the Login and Password for WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
14.12 TYPE JB - Configuring the Jitter Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
14.13 TYPE IPCONF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
14.14 Resetting the Parameters to Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
15 Codec Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
15.1 HFA and Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
15.2 IPDA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
16 Multiple Feature Support Configuration at the Common Gateway (Example) . . . . . . . . . . . . . . . . . . 155
16.1 Important Information / Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
16.2 Configuring Functional Blocks with the AMO BFDAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
16.3 Configuring the Common Gateway Board with the AMO BCSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
A31003-H3160-S104-8-7620, 07/2014
16.4 Configuring SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

16.5 Completed and Uncompleted Functional Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
16.5.1 Uncompleted functional block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
16.5.2 Completed configuration block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
17 Resource Manager Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
17.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
17.2 Key Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
17.2.1 Sector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
17.2.2 Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
17.2.3 Sector Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
17.2.4 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
17.2.4.1 AMO GKTOP: Parameters in the Branch TYPE=RESMGMT1 . . . . . . . . . . . . . . . . . . . . . . . . 170
17.2.4.2 AMO GKTOP: Parameter in the Branch TYPE=IPDA (only for HFA). . . . . . . . . . . . . . . . . . . . 172
17.3 Configuration Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
17.4 Used Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
17.5 Configuring the Resource Management for a HFA Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
17.5.1 Basic Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
17.5.2 Codec Settings for the HFA Subscribers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
17.5.3 Sectors for the LAN/WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
17.5.4 Allocation of the Gateways and Subscribers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
17.5.5 Define Sector Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
17.5.6 Assign the sector paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
17.6 Configuring the Resource Management for an IPDA Configuration with TDM Phones . . . . . . . . . . . . . 181
17.6.1 Basic Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
17.6.3 Sectors for the Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
17.6.4 Allocation of the Gateways to their Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
17.6.6 Assign the Sector Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
17.7 Configuring the Resource Management for an IPDA Configuration with TDM Phones and HFA in Access
Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
17.7.1 Basic Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
17.7.2 Settings for the HFA Subscribers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
17.7.4 Sectors for the Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
17.7.5 Assignment of the HFA Subscribers to the Sectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
17.7.6 Allocation of the Gateways to their Sectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
17.7.8 Assign the Sector Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
17.8 Notes and Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
17.9 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
18 Command Line Interface CLI in HG 3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
18.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
18.2 General Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
18.3 Access control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
18.4 Gateway Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
18.5 Image/File Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
18.6 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
18.7 SSL for WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
18.8 DLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
18.9 Changing the Login and Password for WBM/CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
A31003-H3160-S104-8-7620, 07/2014
19 Command Line Interface CLI at HG 3575 V4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

20 SNMP Support HG 3500 / HG 3575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
21 IP Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
21.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
21.2 Port Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
21.2.1 IP Trunking + DMC (IP Trunking and IPDA) Master Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 263
21.2.2 IPDA (HG 3575/HG 3500) + DMC (HG 3575) master connections . . . . . . . . . . . . . . . . . . . . . . . . . 263
21.3 Information for Network Administrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
21.4 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
21.4.1 Payload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
21.4.2 Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
21.4.3 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
21.4.4 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
22 WBMs of the Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
23 HG 3500 / HG 3575 Diagnostic Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
24 Frequently asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
1.1 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
1.2 Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
1.4 LAN Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
1.5 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
1.6 Advantages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
1.7 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
1.8 Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
2 HiPath 4000 SoftGate Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
2.1 Upgrade via Loadware Update Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
2.2 Upgrade via the Local WBM in HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
3 Mediatrix Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
3.1 Released Mediatrix Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
3.2 Configuration Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
3.3 Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
3.3.1 ISDN (S0) Subscriber (Mediatrix 44xx). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
3.3.1.1 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
3.3.1.2 Sample Scenario with Mediatrix 4402 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
3.3.1.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
3.3.2 S0 Trunking (Mediatrix 44xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.3.2.1 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.3.2.2 Sample Scenario with Mediatrix 4402 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.3.2.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
3.3.3 ISDN (S0) Data Connections (Mediatrix 44xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
3.3.3.1 Requirements for ISDN (S0) Data (Connections) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
3.3.3.2 Sample Scenario with two Mediatrix 44xx Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
3.3.3.3 Trunking Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
3.3.3.4 Subscriber Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
3.3.3.5 Codec Parameter Trunking and Subscriber Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
3.3.4 S2 Interface (Mediatrix 36xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
A31003-H3160-S104-8-7620, 07/2014
3.3.5 Analog Stations (Mediatrix 41xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321

3.3.6 Analog Trunking (Mediatrix 1204) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
3.3.6.1 Configuration on HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
3.3.6.2 Configuration Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
3.4 Fehlersuche mit syslog für Mediatrix 44xx und 36xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
4 Session Border Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
5 Video Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
5.1 Supported Video Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
5.2 Prerequisite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
5.3 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
5.4 Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
5.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
5.5.1 Connections Between Video Endpoints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
5.5.2 Connections Between Video Endpoints and Audio-Only Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . 348
5.6 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
6 LAN Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
7 Music on Hold (MOH) - HiPath 4000 SoftGate as Music on Hold or Announcement Source Provider 353
7.1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
7.2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
7.3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
7.4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
8 Interworking with Microsoft Lync Communication Server 2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
8.1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
8.3 Realization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
8.4.1 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
8.4.2 Available Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
8.4.2.1 Basic Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
8.4.2.2 Call Transfer (blind, semi-attended, attended) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
8.4.2.3 Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
8.4.2.4 Hold and Retrieve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
8.4.2.5 Three-Way Conferencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
8.4.2.6 DTMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
8.4.2.7 SDES Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
8.5 Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
8.5.1 HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
8.5.2 Microsoft Lync Server/Mediation Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
8.5.2.1 Add HiPath 4000 vSTMI as a Gateway to the Lync Server Topology . . . . . . . . . . . . . . . . . . . . 367
8.5.2.2 Define Dial Plan Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
8.5.2.3 Create Voice Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
8.5.2.4 Define Trunk Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
9 Gatekeeper Redundancy for HFA Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
9.1.1 Solution concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
9.1.2 Switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
9.1.3 Prerequisites for switching over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
9.1.4 Switchover process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
A31003-H3160-S104-8-7620, 07/2014
9.3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

9.4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
10 Survivable HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
10.1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
10.3 Generation (example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
11 IPv6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
11.3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
11.3.1 Important Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
11.3.2 IPv6 Networking Connectivity for HiPath 4000 SoftGate (Trunking) . . . . . . . . . . . . . . . . . . . . . . . . 388
11.3.2.1 Configuring Trunking Gateways in HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
11.3.2.2 Configuring the IPv6 Address for HiPath 4000 SoftGate Trunking Gateway (Next Generation
Server) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
11.3.2.3 Configuration in the Virtual HG 3500 SIP WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
11.3.3 IPv6 Internal Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
11.3.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
11.3.3.2 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
11.3.4 NGS Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
11.4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
12 Load Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
12.3.1 Activate SIP Load Balance Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
12.3.2 Activate SIP Load Balancing for the Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
12.3.3 Outgoing/Incoming Calls via SIP Load Balancing Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
12.3.4 SIP Load Balancer Configuration for OpenScape UC Media Server Farm . . . . . . . . . . . . . . . . . . . 408
12.3.5 Load Balancer Status Query. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
13 Secure Remote Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
13.1.1 Secure IP Connectivity via the Internet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
13.1.2 Secure IP Connectivity with Mobile HFA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
13.1.3 Secure IP Connectivity with Gatekeeper Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
13.2.1 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
13.2.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
13.2.3 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
13.2.4 DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
13.2.5 Deployment Service (DLS) and DLS Contact-Me Proxy (DCMP) - Tips & Tricks . . . . . . . . . . . . . . 421
13.2.5.1 Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
13.2.5.2 How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
13.2.5.3 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
13.2.5.4 Information on Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
14 Picture CLIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
A31003-H3160-S104-8-7620, 07/2014
14.3.1 HiPath 4000 SoftGate configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

14.3.2 Phone Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434
14.3.3 LDAP directory server configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
14.3.4 Testing LDAP access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
15 MFC-R2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
15.1 Feature Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
16 HiPath Cordless E Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445
17 WBMs of the Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
Separate LAN Connectivity for Administration and VoIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
4 Relevant AMOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
HiPath Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
RG 8300 V6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
RG 8350 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
Large Enterprise Gatekeeper (LEGK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
1.2 Gatekeeper Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
1.2.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
1.2.2 Key words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
1.2.2.1 Local Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
1.2.2.2 Remote Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
1.2.2.3 IP Address Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
1.3 Gatekeeper Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
2 Guidelines for Installing an IP Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
3 Configuring the Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
3.1 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
3.2 Sequence of Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
3.3 Activating the Large Enterprise Gatekeeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
3.4 Configuring the FLEXAMA Memory in the Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
3.4.1 Number of Internal and External Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
3.4.2 Number of Internal HG 3500 Gateways in a System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
3.4.3 Number of LCR Digit Patterns for Digit Pattern Pools 1 through 8 . . . . . . . . . . . . . . . . . . . . . . . . . . 474
3.4.4 Number of Cache Elements for Cache Pools 1 through 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
3.5 Configuring a HG 3500 on the LAN Segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
3.5.1 Configuring the HG 3500 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
3.5.1.1 Configuring the HG 3500 Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
3.5.1.2 Configuring HG 3500 Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
3.5.1.3 Changing the HG 3500 Gateway Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
3.6 Configuring the HG 3500 Directory Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
3.7 Configuring IP Trunking in the LCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
A31003-H3160-S104-8-7620, 07/2014
3.8 Configuring Circuits and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503

3.8.1 Configuring Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
3.8.2 Configuring Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
3.9 Changing the System Bandwidths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
HiPath Feature Access (HFA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
2 Application Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
2.1.1 Technical background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
2.1.2 HFA user registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
2.2 User interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
2.3 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
2.4 Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
2.4.1 Configuration of the HG 3500 board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
2.4.2 Configuration oth the HFA users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
2.5 Generation via HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
2.5.1 Setting up HG 3500 via the HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
2.5.2 Configure a HFA User via the HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
2.6 Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
2.7 Tuning the voice quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
2.8 Activation of the voice compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
2.9 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
3 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529
Mobile HFA Logon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
1.1 Mobility Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
1.2 Shared Desk Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
2 User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
2.1 Activation/Deactivation via DAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
2.1.1 HFA Logon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
2.1.2 HFA Logoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
2.2 Activation via menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
2.3 Activation with AMO ACTDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
3 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
4 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
4.1 Mobile HFA in Connection with other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
4.1.1 OpenStage terminal in combination with an optiClient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
4.1.2 Malicious Call Identification at visited switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
4.1.3 Signaling and Payload Encryption (SPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
4.2 Please refer to the documentation of „Signaling and Payload Encryption“Restriction . . . . . . . . . . . . . . . . 545
4.3 Language Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
4.4 Logon Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
5 Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
5.1 Example 1: Two HFA subscribers in the same Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
5.2 Example 2: Two HFA subscriber at different systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
5.3 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
IP Distributed Architecture (IPDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
A31003-H3160-S104-8-7620, 07/2014
1 IPDA Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559

1.1 Scalable Increase in System Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560
1.2 Distributed Circuit Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560
1.3 Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
1.4 Call Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
1.4.1 Internal Access Point Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
1.4.2 Call Between Two Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562
1.4.3 Call Between an Access Point and the Central System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
1.4.4 Trunk Access / Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564
1.5 Survivability for Signaling and Payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
1.5.1 Signaling Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566
1.5.2 Payload Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566
1.6 Signaling and Payload Separation (SPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
1.6.1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
1.6.2 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
1.6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
1.7 Redundant LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
1.8 Different Time Zones (DTZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
1.9 A-Law/µ-Law Conversion in AP Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
1.10 Different Announcements, Tones and MFV DialTone Receivers per Access Point . . . . . . . . . . . . . . . . 569
1.11 Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
2 Configuring the IPDA Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571
2.1 HiPath 4000 LAN Segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
2.2 Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591
2.2.1 Configuring a “Networked” Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592
2.2.2 Configuring a “Direct Link“ Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
2.2.3 Changing Access Point Parameters with the AMO STMIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611
2.2.4 Deleting an Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612
2.2.5 Local Configuration of an Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614
2.2.6 Reference Clock in Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617
2.2.7 Loading new Loadware on a HG 3575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618
2.2.8 Updating Access Point Loadware during an RMX Upgrade (New Fix Release/Minor Release) . . . . 620
2.2.9 Information on Exchanging HG 3575 Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622
2.2.10 Information on the 19“ AP 3500 IP Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623
2.2.11 Information on the 19“ AP 3700 IP Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625
2.3 HG 3500 as HG3570 in the HiPath 4000 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626
2.4 Subscriber, CO/Tie Trunk Circuits in Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
2.5 Special Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639
2.5.1 Special Routes Between Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
2.5.2 Special Routes between Access Point and HiPath 4000 LAN Segment . . . . . . . . . . . . . . . . . . . . . . 642
2.6 Signaling Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650
2.7 Quality Monitoring for the Signaling Connection over IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651
2.7.1 Restriction of the Available Signaling Bandwidth (Traffic Shaping) . . . . . . . . . . . . . . . . . . . . . . . . . . 651
2.7.2 Monitoring the Runtime for Signaling Messages (Round Trip Delay) . . . . . . . . . . . . . . . . . . . . . . . . 654
2.7.3 Monitoring Message Throughput . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655
2.7.4 Advanced Criteria for Signaling Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657
2.7.5 Output of Statistical Information on the Signaling Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
2.7.6 Error Messages from Quality Monitoring for the Signaling Connection over IP. . . . . . . . . . . . . . . . . 659
2.7.6.1 F8289 - Output of Statistics Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659
2.7.6.2 F8290 - Net Weakness Start Message Runtime Exceeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661
2.7.6.3 F8290 - Net Weakness Start Message Throughput Undershot . . . . . . . . . . . . . . . . . . . . . . . . . 662
A31003-H3160-S104-8-7620, 07/2014
2.7.6.4 F8291 - Net Weakness End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662

2.7.6.5 F8292 - Bandwidth Requirement Exceeds Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
2.7.6.6 F8293 - Bandwidth Required Back Below Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663
2.8 Source Dependent Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 664
2.9 Payload Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669
2.9.1 When is Payload Survivability Used? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670
2.9.2 How is Payload Survivability Configured? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
2.9.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
2.9.2.2 Variants of Payload Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675
2.9.3 Payload Survivability in HiPath 4000 Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
2.9.4 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
2.10 Signaling and Payload Separation (SPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685
2.10.1 Features and their Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686
2.10.2 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690
2.10.3 General Restrictions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
2.11 Divert Call in Survivability Mode to another Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
2.11.1 Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
2.11.2 User Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
2.11.3 Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695
2.11.4 Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
2.12 External Music on Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
2.13 Information on CMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
2.14 IP Address Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
2.14.1 Change of Address in a Network Segment to which Access Points are Connected . . . . . . . . . . . . 707
2.14.2 Changing the Address of the Survivability Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
2.14.3 Changes in the HiPath 4000 LAN Segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
2.15 A-Law/µ-Law Conversion in AP Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
2.15.1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
2.15.2 Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
2.15.3 Generation (Example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
2.16 Different Announcements, Tones and DTMF DialTone Receivers per Access Point . . . . . . . . . . . . . . . 717
2.16.1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717
2.16.2 Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718
2.16.3 Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719
2.16.3.1 Access Point in a different Country to the Host System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719
2.16.3.2 Access Point with different Companding Algorithm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720
2.16.3.3 Access Point with individual CP Tone <-> SIU Function Assignment . . . . . . . . . . . . . . . . . . . . 720
2.16.3.4 External Announcement Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720
2.16.4 Relevant AMOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
3 Load Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
3.1 Load Calculation for Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726
3.2 Load Calculation for a HG 3500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732
3.3 Calculation Basis - Configuring Payload Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
3.3.1 Configuring Ethernet MAC Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
3.3.2 Configuring IP Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
4 Local Access Point Administration at CLI via Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
4.1 Networked access point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742
4.2 Direct link access point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
4.3 Assignment of parameter names in LW-CLI to the AMO parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 744
A31003-H3160-S104-8-7620, 07/2014
5 Spreadsheets - IPDA Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747

6 Information for network administrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763
6.1 Central Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763
6.2 HG 3500 Voice Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763
6.3 Access Points with HG 3575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 764
6.4 Redundant LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
7 IPDA Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769
7.1 Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769
8 FAQs - Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773
Access Point Emergency (APE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
1 Access Point Emergency Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
1.1 Access Point Emergency Implementation Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
1.1.1 LAN Scenario. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
1.1.2 LAN/WAN Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 786
1.1.3 Branch (WAN) Scenario. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787
1.2 Access Point Emergency and Signaling Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787
1.3 Survivability Unit in AP 3700 IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788
1.4 Survivability unit on HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788
1.5 Allocating Access Points/HiPath 4000 SoftGates to a Survivability Unit. . . . . . . . . . . . . . . . . . . . . . . . . . 789
1.6 Switchover in Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 789
1.7 Reverting to Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 791
1.8 Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792
1.9 Transferring new System Releases and Patches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792
1.10 Connection Between Subsystems (Islands) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792
1.11 Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 793
1.12 Feature Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794
1.13 Application Support in Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794
2 Configuring the APE Feature (Access Point Emergency) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795
2.1 Configuring or Modifying a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000 . . . . . . . . . . . . . . . 796
2.2 Deleting a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798
2.3 Configuring or Modifying an Emergency Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798
2.4 Deleting an Emergency Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803
2.5 Configuring Access Points/HiPath 4000 SoftGates for AP Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . 804
2.6 Examples for Determination of Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 806
2.7 Removing Access Points/HiPath 4000 SoftGates from the AP Emergency Configuration . . . . . . . . . . . . 808
2.8 Deleting the entire AP Emergency Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 808
2.9 Configuring the Display for AP Emergency on the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 809
2.10 Defining the Switchover Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810
2.11 Querying the Connection Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
2.11.1 Querying the Connection Data via Configuration Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
2.11.2 Querying the Connection Data via AMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
2.12 Administration Switchover of Access Points/HiPath 4000 SoftGates . . . . . . . . . . . . . . . . . . . . . . . . . . . 814
2.12.1 Administration Switchover of Access Points/HiPath 4000 SoftGates via Configuration Management . .
814
2.12.2 Administrator Switchover of Access Points/HiPath 4000 SoftGates via AMO . . . . . . . . . . . . . . . . . 814
2.13 Time Synchronization Between the Host System and CC-AP/Survivable HiPath 4000 SoftGate . . . . . 817
2.14 Initial Startup of the CC-AP/Survivable HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817
2.14.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817
2.14.2 CC-AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 818
A31003-H3160-S104-8-7620, 07/2014
2.14.3 Survivable HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 818

2.15 Verification and Acceptance of the AP Emergency Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 818
3 Backup & Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 821
3.1 HiPath 4000 Assistant Backup & Restore on HiPath 4000 Host System . . . . . . . . . . . . . . . . . . . . . . . . . 821
3.1.1 Configuring an AP Backup Server with HiPath 4000 Assistant Backup & Restore . . . . . . . . . . . . . . 822
3.1.2 Creating a Schedule for the Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 824
3.1.3 Performing the First Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825
3.1.4 Using HiPath 4000 Assistant Backup & Restore for more extensive Changes in the System . . . . . . 825
3.1.5 Checking the Regular Activities of HiPath 4000 Assistant Backup & Restore . . . . . . . . . . . . . . . . . . 826
3.2 HiPath 4000 Assistant Backup & Restore Configuration on the CC-AP/Survivable HiPath 4000 SoftGate 827
3.2.1 Configuring the AP Backup Server on the CC-AP/Survivable HiPath 4000 SoftGate . . . . . . . . . . . . 827
3.2.2 Configuring a Routine Configuration Data Backup to Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . 829
4 Service Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 831
4.1 Upgrading the AP Emergency Server (New Fix Release/Minor Release) . . . . . . . . . . . . . . . . . . . . . . . . . 831
4.2 Replacing the DSCXL2 in the AP Emergency Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 831
5 Spreadsheets - APE Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833
6 Information for network administrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 837
6.1 Survivability Unit for AP Emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 837
7 Quick Guide to Setting up an AP Emergency (IPDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 839
7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 839
7.2 Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
7.3 Configuration Steps in HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
7.4 Configuration Steps in the CC-AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 846
7.5 Verification and Acceptance of the AP Emergency Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850
8 FAQs - Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853
Different Time Zones (DTZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 855
3 Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 859
3.1 Configuring the Time Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860
3.2 Assigning the Time Classes to an AP Shelf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 862
3.3 Assigning the Time Classes to an HFA Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 862
3.4 Deleting a Time Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863
3.5 Deleting the Daylight Savings Time Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 864
3.6 Changing the System Date/Time with AMO DATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 867
Signaling Survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 869
1.1 How is the Fault Detected? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870
1.2 What is Used as an Alternative Route for Signaling? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872
1.2.1 Signaling Survivability via PSTN Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873
1.2.2 Signaling Survivability via Alternate LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875
1.3 HSR via UDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876
A31003-H3160-S104-8-7620, 07/2014
2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877

3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
3.1 Signaling Survivability via PSTN Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
3.1.1 Configuring the HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
3.1.2 Configuring the Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 885
3.1.3 Configuring the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
3.1.3.1 Signaling Flow Survivability for “Networked“ Access Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
3.1.3.2 Signaling Flow Survivability for “Direct Link“ Access Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
3.1.3.3 Signaling Survivability with WAML Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
3.1.3.4 External ISDN Router as the Survivability Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894
3.2 Signaling Survivability via alternate LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896
3.2.1 Configuring the HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896
3.2.2 Configuring the LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
3.2.3 Configuring the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
3.2.4 Replacement of a defect NCUI Board with a new NCUI Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 899
3.3 Is Signaling Survivability Currently Active? (DIS-UCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900
4 Relevant AMOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 905
SIP Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
1.1 Communication Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
1.1.1 SIP Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
1.1.2 SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
1.2 SIP Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 908
1.3 Supported RFCs (Request for Comments) for SIP Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 908
1.4 Boards Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 911
2 SIP Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913
2.1 SIP Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913
2.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915
2.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915
2.3.2 SIP Session Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 916
2.3.3 CSTA/ACL Monitoring of SIP Subscribers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
2.3.4 Message Waiting Indication (MWI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918
2.3.5 SIP Subscriber as Member/Master of an ONS Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 919
2.3.6 SIP Subscriber as DSS Key on a Desktop Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925
2.3.7 SIP Peer Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926
2.4 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927
2.4.1 Restrictions of System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927
2.4.2 Restrictions of Terminal Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 928
2.5 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929
2.5.1 STMI2/4 Board Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929
2.5.2 Configuring a SIP Subscriber. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 930
2.5.3 Removing a SIP Subscriber. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931
2.5.4 Changing a SIP Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931
2.5.5 Enabling/Disabling DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931
2.5.6 Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
2.5.7 Second Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
2.5.8 Display of the SIP Subscribers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
2.5.9 Signaling of SIP Subscriber Outage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
2.5.10 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
A31003-H3160-S104-8-7620, 07/2014
3 SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939

3.1 SIP-Q Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939
3.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939
3.1.1.1 Connectivity to OpenScape Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939
3.1.1.2 HiPath Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 940
3.1.1.3 Codecs per Destination Gateway for SIP-Q Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 941
3.1.1.4 SIP Peer Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 941
3.1.2 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 941
3.1.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 942
3.2 Native SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943
3.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943
3.2.2 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 944
3.2.3 Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945
3.2.3.1 SIP Service Provider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945
3.2.3.2 Remote Agent Server Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946
3.2.3.3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946
3.2.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947
3.2.4.1 General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947
3.2.4.2 Codec Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947
3.3 SIP Trunk Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
3.3.1 Advantages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
3.3.2 Disadvantages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
3.3.3 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
3.3.4 Default Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 949
3.3.5 Activating the SIP Trunk Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 949
3.3.5.1 Native SIP Trunk Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 949
3.3.5.2 SIP-Q Trunk Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
3.3.6 "SIP Trunk Profiles" menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
3.3.6.1 Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951
3.3.6.2 Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 952
3.3.6.3 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 952
3.3.6.4 Activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
3.3.6.5 Deactivate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
3.3.6.6 Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
3.3.7 Configuration of SIP Trunks with/without Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
3.3.7.1 Native SIP Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 955
3.3.7.2 SIP-Q Trunks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 959
4 SIP Service Provider / SIP Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
4.1 Motivation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
4.2 HiPath 4000 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
4.3 Configuration Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
4.3.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
4.3.2 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966
4.4 Scenario 1: Gateway direct to SIP Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
4.4.1 Initial Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
4.4.2 AMO Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 968
4.4.3 Gateway Configuration in WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969
4.5 Scenario 2: Gateway via Session Border Controller to SIP Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971
4.5.1 Initial Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971
4.5.2 AMO Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
4.5.3 HG 3500 Configuration in WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 974
A31003-H3160-S104-8-7620, 07/2014
4.5.4 Configuration in the Session Border Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976

5 Configuration of SIP-Q-Trunking / Native SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
5.1 Configuration using AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
5.1.1 Trunking Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
5.1.2 Configuring a HG 3500 as a Local Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
5.1.2.1 Configuration in Node 10-69-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978
5.1.2.2 Configuration in Node 10-69-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 982
5.1.2.3 Extension in Node 10-69-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 984
5.1.2.4 Call from Node 10-69-100 to Node 10-69-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 984
5.1.3 Backup & Restore of the WBM Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 985
5.1.4 Displaying Link Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986
5.1.5 Procedure for Adding Supplementary HG 3500 Boards to the Network . . . . . . . . . . . . . . . . . . . . . . 986
5.1.6 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986
5.2 Configuration with HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 989
5.2.1 Configure Common Gateway HG 3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 989
5.2.2 Delete IPGW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991
5.2.3 Modify Board Data of IPGW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991
5.3 Configuration using SIP Trunk Profiles in WBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992
5.4 SIP-Q Trunking between HiPath 4000 and OpenScape Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992
5.4.1 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992
5.4.2 HiPath 4000 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993
5.4.3 OpenScape Voice Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 996
5.5 Number management between HiPath 4000 and OpenScape Voice for Italy . . . . . . . . . . . . . . . . . . . . . 999
H323 / H323 Annex Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1003
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1003
2 DTMF Outband Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
3 Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
3.1 Configuration using AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
3.1.1 Trunking Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
3.1.2 Configuring a HG 3500 as a Local Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
3.1.2.1 Configuration in Node 10-69-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1008
3.1.2.2 Configuration in Node 10-69-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011
3.1.2.3 Extension in Node 10-69-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1014
3.1.2.4 Call from Node 10-69-100 to Node 10-69-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1014
3.1.3 Backup & Restore of the WBM Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1015
3.1.4 Displaying Link Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1016
3.1.5 Procedure for Adding Supplementary HG 3500 Boards to the Network . . . . . . . . . . . . . . . . . . . . . 1016
3.1.6 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1016
3.2 Configuration with HiPath 4000 Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017
3.2.1 Configure Common Gateway HG 3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017
3.2.2 Delete IPGW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020
3.2.3 Modify Board Data of IPGW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020
Signaling and Payload Encryption (SPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
1.1 Encrypted Signaling and Payload Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
1.2 Scenarios - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031
1.3 Solution Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
1.3.1 PKI (Public Key Infrastructure). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
1.3.2 Signaling encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033
A31003-H3160-S104-8-7620, 07/2014
1.3.3 Voice Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035

1.4 MIKEY (Multimedia Internet KEYing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
1.4.1 MIKEY Option 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
1.4.2 MIKEY Option 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
1.5 Session Description (SDES) Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
1.6 Master Encryption Key (MEK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
1.7 Secure SIP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
1.7.1 SIP-Q Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1038
1.7.2 Native SIP trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039
2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
2.1 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
2.2 Generation of a Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
2.3 Supported Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042
2.4 Board Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042
2.5 Standby CGW Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042
2.6 Activating/Deactivating SPE for Subfunctions in the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1043
2.7 Connection to Gateway Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1043
2.8 SPE in Connection with Mobile HFA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1044
2.8.1 Terminology used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1044
2.8.2 Prerequisite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1045
2.8.3 Scenarios with Homogenous HiPath 4000 Network with SPE Enabled . . . . . . . . . . . . . . . . . . . . . . 1045
2.8.4 Scenarios within a Network with SPE activated Nodes and SPE deactivated Nodes . . . . . . . . . . . 1046
2.8.5 Network Wide Usage of Mobile HFA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1048
3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049
3.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050
3.2 Activation / Deactivation of SPE for Gateways with AMO CGWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050
3.3 Trunk SPE Activation / Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052
3.3.1 SPE for Analog / TDM Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052
3.3.2 SPE for IP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
3.3.3 Deactivation of SPE for SIP-Q / Native SIP Trunking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061
3.4 Terminal SPE Activation / Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061
3.4.1 SPE for Analog/TDM Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062
3.4.2 SPE for IP Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1062
3.4.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1063
3.4.4 Signaling at the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066
3.4.4.1 Display in Call State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066
3.4.4.2 Display in Idle State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067
3.4.4.3 Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067
3.4.5 Deactivating SPE for Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068
3.5 Activation / Deactivation of SPE for Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
3.5.1 New Access Point in an Active SPE System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1071
3.5.2 Deactivating SPE for Access Points with Soft Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073
3.6 HiPath 4000 SoftGate SPE Activation / Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
3.6.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
3.6.2 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
3.6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1075
3.6.3.1 Scenario 1: Activate a HiPath 4000 SoftGate on a host system that already has SPE activated . . .
1075
3.6.3.2 Scenario 2: SPE is neither activated on HiPath 4000 SoftGate nor at host system . . . . . . . . . 1077
A31003-H3160-S104-8-7620, 07/2014
4 Secure Trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1079

4.1 Impact on the Service Contract. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1079
4.2 Secure Trace Possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1080
4.3 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1080
4.4 Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1082
4.4.1 Loading a Secure Trace Certificate onto the Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1083
4.4.2 Activating a Secure Trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1083
4.4.3 Secure Trace State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1085
4.4.4 Secure TraceBeacons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1085
4.5 Verify Correct Activation of the Traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1087
4.6 Decryption of Traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1088
5 Generation SPE Certificates with HiPath 4000 Assistant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1091
5.1 SPE Root Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1091
5.1.1 Open the SPE Root Certificate Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1091
5.1.2 Creating a New Root Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1092
5.1.3 Displaying/Downloading the newly Created SPE Root Certificate. . . . . . . . . . . . . . . . . . . . . . . . . . 1094
5.2 SPE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1095
5.2.1 Open the SPE Certificate Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1095
5.2.2 Creating a new SPE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1095
5.2.3 Displaying/Downloading the newly created SPE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1098
6 Deployment Service (DLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099
6.1 Distribution of Certificates to Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099
6.1.1 Creating a Virtual IP Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099
6.1.2 Scanning the IP Devices (IP Gateways) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1103
6.1.3 Distribution of the CA Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1106
6.1.4 Distribution of the SPE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108
6.1.5 Resetting Bootstrapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111
6.1.5.1 DLS Bootstrapping Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1111
6.1.5.2 Gateway Bootstrapping Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1112
6.2 Distribution of Certificates to Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1112
6.2.1 Distribution of a CA Certificate (Terminals) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1112
6.2.2 Scanning the IP Devices (Terminals). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1115
7 Distribution of Certificates with the WBM of the Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1119
7.1 Importing SPE CA Certificate for SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1119
7.2 Importing a SPE Certificate for SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120
7.3 Importing a SPE Certificate for HFA Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120
7.4 Certificates and Security on vHFA and WAN Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1121
8 AutoSPE Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1123
8.1 HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1123
8.2 Deployment Service (DLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124
8.2.1 DLS Time Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124
8.2.2 Preparing DLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124
8.3 Device Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125
8.3.1 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125
8.3.2 Time Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126
8.4 Automatic Certificate Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126
8.5 Activate Voice Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
8.6 Check Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
8.7 Checking SPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1128
8.8 Adding new Gateways after AutoSPE Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1128
A31003-H3160-S104-8-7620, 07/2014
Payload Switching DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1131

1 Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1131
2 Direct Media Connect (DMC) in Connection with HFA Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . 1133
2.1.1 Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1133
2.1.2 Notes concerning Direct Media Connections DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134
2.1.3 Bandwidth Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134
2.1.3.1 General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134
2.1.3.2 Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1135
2.1.3.3 HFA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1136
2.1.4 Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1136
2.1.5 Domain concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139
2.1.6 DMC Interworking to HiPath 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1140
2.2.1 Features with DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1143
2.2.2 Feature activation while DMC is active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1144
2.3 Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1144
2.3.1 DMC Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1144
2.3.2 Maximum number of DMC connections on IP boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145
2.3.3 Voice Activity Detection (VAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145
2.3.4 Domains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1146
2.3.5 H.323 stack on IPDA boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1146
2.3.6 Troubleshooting Hints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1146
2.4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148
3 Direct Media Connect (DMC) in Connection with SIP Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151
3.2 Restriction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1153
3.3 Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1154
3.3.1 SIP Subscriber at same HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1154
3.3.2 SIP Subscriber at another HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1155
3.3.3 SIP Subscriber at OpenScpae Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1156
3.3.4 SIP Subscriber at HiPath 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157
3.3.5 HFA Subscriber at same HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1158
3.3.6 HFA Subscriber at another HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159
3.3.7 HFA Subscriber at HiPath 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1161
3.3.8 TDM Subscriber/Network behind a Remote Shelf of a HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . 1162
3.3.9 TDM Subscriber/Network at another HiPath 4000 behind a Remote Shelf . . . . . . . . . . . . . . . . . . . 1163
3.3.10 TDM Subscriber/Network at another HiPath 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1164
3.3.11 TDM Subscriber at HiPath 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166
4 Direct Media Connect (DMC) in Connection with HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . 1167
T.38 Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177
1 Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177
2.1 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1179
2.2 Common Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1180
2.3 HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1180
2.4 IPDA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1180
A31003-H3160-S104-8-7620, 07/2014
3 Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1183
4.1 HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187
4.2 IPDA (NCUI/STMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187
5 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189
6 Relevant AMOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191
IP Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193
1 Supported IP Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193
2 Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195
3 Description of optiPoint IP Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197
3.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197
3.2 optiPoint 410/420 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197
3.2.1 Terminal Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197
3.2.2 Adapters and key modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1198
3.3 optiPoint WL2 professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199
3.4 More Adapters and Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199
3.4.1 OpenStage Busy Lamp Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199
3.4.2 optiPoint Recorder Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200
3.4.2.1 Port for Recording Device (Data cannot be modified) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1201
3.4.2.2 Second Headset Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1201
3.4.3 optiPoint Acoustic Adapter Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1202
3.4.4 Microphone and Loudspeaker Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1202
3.4.5 Headset Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1203
3.4.6 Contact Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1203
4 Description of OpenStage IP Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
4.1 Hardware and General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
4.2 Key Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
4.3 Key Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
4.4 OpenStage Terminal in Connection with optiClient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1206
4.5 Busy Lamp Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207
5 SIP Subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209
6.1 General Configuration Rules and Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211
6.2 Adapter for optiPoint Telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211
6.3 Modules for optiPoint Telephones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211
6.4 Key Layout on optiPoint Telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1212
7 IP Terminal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213
7.1 An optiPoint 410 or OpenStage at STMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213
7.2 PC After optiPoint 410. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214
7.3 An optiPoint 410 and USB for Simple Dialer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1215
7.1 optiPoint WL2 professional Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1216
7.2 OpenStage Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1217
8 Deletion at the IP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221
8.1 Deleting All Devices Assigned a Station Number at the IP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221
8.2 Deleting NV Services at the IP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221
8.3 Deleting the IP Telephone’s Key Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221
8.4 Deleting IP Telephone Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1221
A31003-H3160-S104-8-7620, 07/2014
HiPath Cordless IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1223

2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
2.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
2.2 Restrctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
2.3 More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225
3 Configuration in HiPath 4000 (Example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227
4 Relevant AMOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1231
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1233
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1235
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1243
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1245
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
highlights_hinweise_ab_v6.fm
Highlights and Hints

Latest issue
• Gateways HG 3500 and HG 3575
– Bit Rate: Auto negotiate is fully supported as of Senta version 12.
– Update for parameter TYP=SIGQOS (see Section 12.11, “TYPE SIGQOS

- Quality Monitoring for the Signaling Connection over IP”).
– Note regarding the use of trunking protocols in connection with multiple

feature support configuration (see Section 16.1, “Important Information /
Restrictions”).
– Update in Section 21.4.2, “Signaling”.
– New paragraph regarding IP Interface MTU (see Section 3.3, “Network

Requirements”).
• Signaling Survivability
– Updates regarding Short Hold in Section 3.1.3.3, “Signaling Survivability

with WAML Replacement”.
– Information about the needed firmware version for the external router to
assure signaling survivability at the HiPath 4000 SoftGate with an
external ISDN router (see Chapter 2, “Service Information”).
– Note regarding HiPath 4000 SoftGate in connection with signaling

survivability (see Chapter 2, “Service Information”).
– Update for feature “HSR via UDP”.
• IP Distributed Architecture (IPDA)
– Signaling and Payload Separation: The restriction concerning ACD

agents and branches (ACD agents must be located on the same branch)
is not valid anymore.
– Enhancements in Section 2.11, “Divert Call in Survivability Mode to

another Access Point” incorporated.
– Payload Survivability: Restriction using VNR and payload survivability

(siehe Section 2.9.4, “Restrictions”).
• Access Point Emergency
– Enhanced information to the switchover delay time (see Section 2.10,

“Defining the Switchover Delay”).
– New information in the FAQs (see Chapter 8, “FAQs - Frequently Asked

Questions”).
• HiPath 4000 SoftGate
A31003-H3160-S104-8-7620, 07/2014
– New features added:
– RQ00030980: Licensing for HiPath Access modules directly

connected to a HiPath 4000 SoftGate.
– 9 periperal slots for virtual boards or HiPath Access modules are

available.
– Up to 18 different tones and 6 different announcements are available.
– RQ00033039: QDC support

For more information please refer to Section 1.3, “Features”.
– RQ00033880: MFC-R2 support (see Chapter 15, “MFC-R2”).
– More information regarding SLMA2 and TMOM2 (see Section 7.2,

“Service Information” > Details).
– SIP Load Balancer enhancements for the support of OpenScape UC

Media Servers (see Section 12.3.4, “SIP Load Balancer Configuration for
OpenScape UC Media Server Farm”).
• Payload Switching DMC

Several enhancements in the whole document, e.g.:
– Section 2.1.3, “Bandwidth Considerations”
– Section 2.3.6, “Troubleshooting Hints”
Issue 07
• RQ00033881: Separat LAN Connectivity for Administration and VoIP
– Improvements in Chapter 3, “Generation (Example)” and Chapter 4,

“Relevant AMOs” implemented.
• Access Point Emergency (APE)

Actualization of Quick Guide to Setting up an AP Emergency (IPDA).
– RQ00034930: NCUI SSH access enabled to be able to change NCUI

basic configuration (CCA/CCB/CCC) from remote (siehe Section 2.14.3,
“Changes in the HiPath 4000 LAN Segment”).
– Signaling Survivability is aslo released for HiPath Access (see Chapter 2,

“Service Information”).
– Signaling Survivability with WAML Replacement is only supported for

Common Gateway Boards (see Chapter 2, “Service Information”).
• SIP Connectivity
A31003-H3160-S104-8-7620, 07/2014
– SIP-Peer-Filtering für HG 3500 und vHG 3500 SIP (siehe Section 2.3.7,
“SIP Peer Filtering”).
– Firewall-Kapitel gelöscht, da die Firewall muss nicht mehr vom Kunden

konfiguriert werden. Dies erfolgt automatisch entsprechend der Konfigu-
ration des HiPath 40000 SoftGates.
– Gatekeeper redundancy for HFA subscriber is not released in connection

with the feature Access Point Emergency (APE) (see Section 9.2,
“Service Information”).
– Enhancements in documentation for the feature “Secure Remote

Subscriber” implemented (see Chapter 13, “Secure Remote Subscriber”).
– RQ00035073: Enhancements in documentation for the feature “Picture

CLIP” implemented (see Chapter 14, “Picture CLIP”).
• HiPath Gateways HG 3500 und HG 3575
– Links to IFMDB updated (see Section 21.2, “Port Range”).
• Signaling and Payload Encryption (SPE)
– Updates regarding vHG 3500 HFA: CA certificate is not needed. Only

SPE certificate is required.
– The Try to decode RTP outside of conversation function must be

selected to see RTP trace beacons (see Section 4.5, “Verify Correct
Activation of the Traces”).
Issue 06
• IP Distributed Architecture
– Available resources for each access point added to FAQs (see Chapter
8, “FAQs - Frequently Asked Questions”).
– Important information for signaling survivability with HiPath 4000

SoftGate (see Chapter 2, “Service Information”).
– Update in Section 3.1.3.3, “Signaling Survivability with WAML

Replacement”.
– RQ00031771: Signaling Survivability via alternate LAN.
• HiPath 4000 SoftGate:
– RQ00032508: Support of calls to/from Lync Communication Server 2010

over HiPath 4000 SoftGate via native SIP trunks. As of HiPath 4000 V6
R2 secure SIP trunking via SDES (RQ00034255) is supported.
See Chapter 8, “Interworking with Microsoft Lync Communication Server
A31003-H3160-S104-8-7620, 07/2014
2010”.
– Available resources for each HiPath 4000 SoftGate added (see Section
1.3, “Features”).
– RQ00032854: No restrictions regarding MOH and announcements for

Flexrouting, synchronized announcements and announcement unit
anymore (see Chapter 7, “Music on Hold (MOH) - HiPath 4000 SoftGate
as Music on Hold or Announcement Source Provider”).
– RQ00032951: Remote subscriber with full HFA feature content (see

Chapter 13, “Secure Remote Subscriber”).
– RQ00033509: This feature provides the option of showing centrally

stored contact data (name and picture) of the remote telephone party on
an IP phone’s display during the call (see Chapter 14, “Picture CLIP”).
– RQ00033327: Empty display of a SIP device if no name is configured in

AMO PERSI (see Section 2.3, “Features”).
– Different updates in the whole document.
• LAN Interfaces
RQ00033881: Separate LAN interfaces are available for administration and
voice over IP for HiPath 4000 SoftGate, HG 3575 and HG 3500.
Issue 05
– New structure for backup and restore items (see Chapter 3, “Backup &
Restore”).
– New chapter for service scenarios (see Chapter 4, “Service Scenarios”).
– Handling for replacing a DSCXL2 in an AP emergency server added (see

Section 4.2, “Replacing the DSCXL2 in the AP Emergency Server”).
• HiPath Gateways HG 3500 / 3575
– Updated chapter for resource manager (see Section 5.8, “Resource

Manager (RM)”and Chapter 17, “Resource Manager Functionality”).
– Error correction in Section 4.1.1, “General Information” regarding multiple

feature support.
– New MIB for HiPath 4000 and hint on SNMP configurator added (see
Chapter 20, “SNMP Support HG 3500 / HG 3575”).
– IPv6 update (see Chapter 11, “IPv6”).
A31003-H3160-S104-8-7620, 07/2014
– Mediatrix gateways: Configuration note added (see Section 3.2,

“Configuration Notes”).
– Update of Section 3.1.3.3, “Signaling Survivability with WAML

Replacement”.
• Large Enterprise Gatekeeper

Note concerning registration added and appropriate sections deleted (see
Section 3.1, “Important Information”).
– Further review inputs incorporated in the whole document.
– Note on manually generating a certificate (see Section 2.2, “Generation

of a Certificate”).
– New structure for the whole SIP Connectivity document.
Issue 04
– Review inputs incorporated in the whole document.
– Updates in Section 4.1, “Upgrading the AP Emergency Server (New Fix

Release/Minor Release)” incorporated.
– Review inputs for IPv6 (see Chapter 11, “IPv6”).
– Review inputs for SIP load balancing (see Chapter 12, “Load Balancing”).
– Review inputs incorporated in the whole document.
Issue 03
• Signaling and Payload Encryption
– New link for public key for secure trace (see Section 4.3, “Configuration”).
– New link for HiPath Plugin (see Section 4.6, “Decryption of Traces”).
– Update of agreement for secure trace activation (see Section 4.1, “Impact
on the Service Contract”).
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
gateways_01_ziel.fm
Goal of this Document
Gateways HG 3500 and HG 3575
1 Goal of this Document

This document aims to provide an overview of the HG 3500 and HG 3575
gateways. Only the basic board configuration is described. Detailed information
on specific functions such as IP Distributed Architecture and Access Point
Emergency (IPDA & APE), HiPath Feature Access (HFA), Large Enterprise
Gatekeeper, etc. are provided in the corresponding sections.
A31003-H3160-S104-8-7620, 07/2014
gateways_01_ziel.fm
Goal of this Document
A31003-H3160-S104-8-7620, 07/2014
gateways_02_terms.fm
Terms
Key Words
2 Terms
2.1 Key Words

In order to prevent confusion, a number of key terms which are used frequently
within the text are defined here in more detail.
Nodes: Designates a device with a port/connection in a network.

This can be a router, a CGW module or any computer. Also frequently
referred to as “Host“.
LAN segment: Part of a network in which all nodes communicate with each other
directly on Layer 2 (Ethernet MAC). The nodes are thus switched on
the same “shared“ medium and interconnected via hubs or Layer 2
switches. In other words, they communicate without routers (Layer 3).
The communication with nodes beyond this segment has to be
realized via routers.
IP address: A numerical Internet address comprising 4 sets of digits, e.g.
172.16.222.45. In this context, the term always designates the
individual, complete and unequivocal address of a node.
Network mask Internet addresses are broken down into network-specific and node-
(Netmask): specific sections. The size of these sections differs, depending on the
class of the address (determined by the first digit of the address).
Byte 1 2 3 4
Class
A Network [1 .. Node Node Node
B Network [128 .. Network Node Node
C Network [192 .. Network Network Node
The netmask allows subnets to be generated within a network.
Specific bits of the node section are used for the purposes of
addressing. The network mask specifies which parts of the IP address
are to be regarded as network/subnet sections by means of the
specified bits. The remaining digits (bits not specified in the mask)
designate the node section.
Network In this document, the term network address is used for the entire
address: network and subnet part of the IP address.
The network address is yielded by a bit-by-bit AND operation of any IP
address with the netmask.
VLAN tagging According to IEEE 802.1 p/q, there are two functions which are
controlled using a common tag: the priority and the VLAN ID. The
term VLAN tagging is generally applied once the tag is used -
regardless of what it is being used for. The same applies in the case
of IPDA. When reference is made to deactivating or activating VLAN
tagging (AMOs SIPCO or CGWB: VLAN), it is the tag that is meant, not
the VLAN function.
According to the standard there are three types of frames:
A31003-H3160-S104-8-7620, 07/2014
Terms
Key Words
• Untagged Normal Ethernet frames without tagging

• Priority Tagged Ethernet frames with tagging
The priority bits are used
The VLAN ID is 0.
• VLAN Tagged Ethernet frames with tagging
The priority bits are 0,
The VLAN ID is > 0.
Some IP equipment vendors only allow priority bits to be used when
VLAN ID > 0 is set.
When tagging is being used, the IPDA components always use priority
tagging, but allow a setting of VLAN ID > 0
The priority bits are fixed according to the traffic type.
The values are specified in Table 3, “TOS values”.
TOS byte The Type Of Service byte is a component of the header for all IP
packets in accordance with RFC 791.
According to RFC 791 (Internet Protocol), the byte is split up as follows 
(most significant -> least significant bit)
3 bits for precedence 3 bits for priority 2 bits reserved
D-T-R for future use
111 - Network Control Slight delay:
110 - Internetwork Control 0 = Normal, 1 = Low
101 - CRITIC/ECP Throughput:
100 - Flash Override 0 = Normal, 1 = High
011 - Flash Reliability:
010 - Immediate 0 = Normal, 1 = High
001 - Priority
000 - Routine
According to RFC 2474 (Differentiated Services), the six high-order
bits are used as DiffServ Code Point (DSCP), while the two least
significant bits are reserved.
Some of the values to be set are specified as 6-bit values without the
2 reserved bits, and others as 8-bit values (with the 2 reserved bits =
0).
With IPDA, the entire TOS byte is always specified. The two least
significant bits are always set to zero.
A pure DiffServ Code Point must therefore be moved 2 bits to the left
or multiplied by 4 in order to obtain the TOS byte setting for IPDA.
IP address
172 16 222 45
1 0 1 0 1 1 0 0 0 0 0 1 0 0 0 0 1 1 0 1 1 1 1 0 0 0 1 0 1 1 0 1
Netmask
255 255 240 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Subnet 1 1 0 1
Network address
Table 1 Example: Class B IP address, netmask and network address
A31003-H3160-S104-8-7620, 07/2014
Terms
Fax or Modem Transmission and Detection
172 16 208 0
1 0 1 0 1 1 0 0 0 0 0 1 0 0 0 0 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Table 1 Example: Class B IP address, netmask and network address
2.2 Fax or Modem Transmission and Detection

The “FMoIP“ (Fax/Modem over IP) feature is used for the transmission of fax and
modem signals over the IP network.
The FMoIP feature provides the following functionality:
• DMC (Direct Media Connect) for fax/modem calls. This results in a maximum
of one IP hop (2 IP/TDM conversions) for fax/modem connections within a
local HiPath 4000 network. DMC is supported for HG 3500 / HG 3575. This
is the major improvement in comparison with the last version, where a switch
back to master call was performed after tone detection.
• The DMC endpoints HG 3500 and HG 3575 support G.711 F/M.
• T.38
IMPORTANT: When connecting a fax adapter to a HG 3500 (SIP

subscriber), DMC must be deactivated for this device (only then is T.38 trans-
mission possible).
If you want nonetheless to connect DMC for this device, the codec must be
set to G.711 (fax transmission with G.711, not T.38).
IMPORTANT: T.38 configuration/usage requires end-to-end DMC between

HiPath 4000 gateways (minimized IP hops) because of timing requirements
according to T.38 standard. In case of multiple IP hops the fax transmission
could fail with some fax machines. Negative list of affected fax machines can
be found in the Release Notes.
IMPORTANT: Only four T.38 connections are possible per DSP. This means
for a 60 channel gateway board 8 T.38 parallel fax calls are possible and for
a 120 channel gateway board 16 (with STMI2) / 20 (with STMI4 (STMI4 with
120 channels has 5 DSPs)) T.38 parallel fax calls are possible. Further fax
calls will then be processed with G711 clear channel.
For more information on whic scenarios are supported please refer to

document “T.38 Fax”, Chapter 2, “Feature Description”.
A31003-H3160-S104-8-7620, 07/2014
Terms
Codec Standards
• RFC2833 and RFC2198 for fax/modem tones are supported for HG 3500/75
to transfer the fax/modem signals over IP.
• Enhanced DSP tone detection (incl. tone information transfer based on

RFC2833/RFC2198) for HG 3500/75 boards. Supported tones:
– call initiation tones CNG and CT (calling side)
– call answer tones ANS(CED), /ANS, ANSam, /ANSam (called side)
Restrictions
• When DMC is not able to reduce the number of IP hops for a connection to
one IP hop, there will still be a certain risk of broken fax or modem
connections because of the resulting delay, even though a G.711 channel
optimized for analog data is chosen.
• Fax/Modem call: only supports basic call, no support for supplementary

services initiated on basis of an existing connection, such as consultation call.
Support of basic call includes forwarded calls (CFU).
• Due to the variety of the available modem and fax types on the market, there
is no guarantee that all FMoIP scenarios will work with 100% reliability. The
different behaviors of the modem and fax types (e.g. tolerance) and the
typical IP conditions (jitter, delay etc.) can result in failed FMoIP scenarios.
• Clear Channel has to be disabled via AMO configuration because there is no

RFC2833/RFC2198 tone detection for Clear Channel. Each fax/modem call
should be configured as a regular voice call (G.711, G.729, ...).
T.38
T.38 is an ITU standard for sending fax messages accross IP networks in a real-
time mode.
2.3 Codec Standards

To transmit an analog voice signal over digital paths, it must be converted to a
digital signal (and then back again). There are different methods for implementing
this codec, each of which offer different levels of voice quality and requires
different amounts of bandwidth.
Detailed information on the codec classmarks is provided in Table 14, “Classmark

handling for codec type” in the document "IP Distributed Architecture (IPA) and
Access Point Emergency (APE)".
A31003-H3160-S104-8-7620, 07/2014
Terms
Voice Quality
2.4 Voice Quality

For the transmission of voice over IP networks, there are three other factors that
influence the subjective voice quality experienced by the customer:
• Delay
Occurs in the packetization of voice data (see Figure 1 Packet-by-packet
voice transmission) and in the transmission of packets. Compression codecs
(e.g. G.729) require processing time. In order to compensate for fluctuations
in the packet runtime (jitter), a buffer is inserted on the receiver side (jitter
buffer). The size of the jitter buffer also influences the overall delay.
• Packet loss
Packets can sometimes be lost during transmission in IP networks. Fill data
must then be inserted on the receive side in place of the required packet data.
• Jitter
Fluctuation of the packet runtime above or below a mean value, see Figure 2
Jitter: variation of the transmission delay. The jitter buffer must intercept these
fluctuations. The packet earmarked for use is lost if the deviation from mean
value is so great that it can no longer be intercepted by the jitter buffer. The
effect is the same as for packet loss in the network.
1 ms
Sender
Transmission
runtime
Receiver
ISDN: Byte-by-byte transmission, continuous data
30 ms
t
Transmitter
Packetization delay
(sample size)
1 ms
Transmission
runtime
Receiver
IP: Packet-by-packet transmission, packet can only be sent when it is full
Figure 1 Packet-by-packet voice transmission
A31003-H3160-S104-8-7620, 07/2014
Terms
Voice Quality
Sender Receiver
t0 t0
vario
T
us n
etw ransmis
Transmission
o rk
com sion b
tR min
transmission delay
pon y
IP ents
N
Variation of the
delay
etw
Jitter
ork tR tR avg
tR max
t
Mean value Worst case
Figure 2 Jitter: variation of the transmission delay
The effectiveness of both parameters also depends on the sample size (how
many milliseconds of voice per packet) and on the codec type.
Figure 3 Voice quality depending on delay illustrates an evaluation of voice quality

depending on delay.
User satisfaction
100
Very
satisfied
90
Satisfied
80 Some
% users
70
Many
users
60
Extremel
y
50
0 100 200 300 400 500
One-way delay [30 ms] (with 65 dB echo attenuation)
Figure 3 Voice quality depending on delay
Table 2, “Voice quality depending on delay and packet loss rate” illustrates an
evaluation of voice quality depending on delay and packet loss rate.
Scale of acceptance
Value Acceptance
0-5 Very good
6 - 10 Good
11 - 19 Satisfactory
Table 2 Voice quality depending on delay and packet loss rate
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer
20 or more Unsatisfactory
Delay Packet loss rate in %

[ms]
< 1% 1% 1.5% 2% 2.5% 3% > 3%
50 0 4 6 8 10 12 30
100 0 4 6 8 10 12 30
150 0 4 6 8 10 12 30
200 3 7 9 11 13 15 33
250 10 14 16 18 20 22 40
300 15 19 21 23 25 27 45
350 20 24 26 28 30 32 50
400 25 29 31 33 35 37 55
Table 2 Voice quality depending on delay and packet loss rate

For all solutions over IP, i.e. including HiPath 4000, configurations with multiple
IP-TDM (or TDM-IP) conversions in a connection should be avoided, as each
conversion creates a delay. This is because of the potential losses in voice
quality where the number of delays is too high. Every module in the HG 3500
family (and HG 3575 in the access point) as well as every terminal device
distributed directly via HFA has a IP-TDM conversion. The maximum number of
IP-TDM conversions should (not including HFA terminal devices) be no higher
than two.
2.5 Jitter Buffer
2.5.1 Jitter Buffer Functionality

Transfer packets can arrive with different delays in TCP/IP-based networks.
Because these delays cause interruptions, packets entering the data stream must
be verified. The jitter buffer provides temporary storage for IP packets. It can
balance out IP packet delays to a certain degree.
IP packets enter the jitter buffer in the order in which they arrive. Each packet
contains a time stamp, which is stored in the RTP header of the packet. The
actual order is determined using the packet time stamps. The jitter buffer ensures
that packets leave in the right order and in sync. An average time (average delay)
defines how long packets, which arrive at the expected time, are held in the jitter
buffer. Packets which arrive later than expected are held for a shorter period in
the jitter buffer; packets which arrive earlier than expected are held longer. If a
packet arrives so late that it can no longer be assigned, it is lost. In theory, packets
can also arrive so early that they cannot be assigned. This is, however, rarely the
case in practice.
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer
Figure 4 Jitter buffer functionality illustrates the jitter buffer functionality.
If one or two packets are lost during voice transmission, this is not an immediate
problem. However, the delay should be as short as possible, as delays which are
too long compromise voice quality when making calls.
To ensure data integrity, the number of packets lost during data transfer should
be kept to a minimum. Delays, on the other hand, do not play a major role here.
Key: Buffer area for packets which arrive early

Buffer area for packets which arrive on time
Buffer area for packets which arrive late
Scenario 1: n Packet arrives on time
n-1 n-2 n-3 n-4
Jitter Buffer
Scenario 2: Delayed packet arrives

n-3 (can still be allocated)
n-1 n-2 n-4
Jitter Buffer
Scenario 3: n-5 Packet arrives too late

Packet is lost
n-1 n-2 n-4
Jitter Buffer
Packet arrives too early

Scenario 4: n+2 (can be allocated, is held longer in the buffer)
n-1 n-2 n-3 n-4
Jitter Buffer
Figure 4 Jitter buffer functionality
2.5.2 Jitter Buffer Modes

The jitter buffer of the gateways HG 3500/3575 can be operated in two different
modes, depending on the connection:
• Static jitter buffer
• adaptive (dynamic) jitter buffer
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer
The adaptive jitter buffer is designed specifically for voice transmission. While the
average packet delay remains constant in static mode, it automatically adapts to
the situation in adaptive mode. Figure 5 Difference between static and adaptive
jitter buffer illustrates the difference between static and adaptive jitter buffers in a
situation where several packets with longer delays arrive.
In the adaptive jitter buffer, the average delay is simply the start value for the
average delay. This is automatically adjusted to the respective receive ratios
during operation (green line).
Key: Maximum delay (configurable)

Average delay (configurable, however, only the
start value for jitter buffer)
packets
Static jitter buffer: Average delay is constant.

Packets with higher average delays
are not adapted.
Del
ay
Measured time
Adaptive jitter buffer: Average delay is variable

and is automatically adapted
for packets with higher average delays (however, only as far as the
maximum delay configured).
Del
ay
Measured time
Figure 5 Difference between static and adaptive jitter buffer
2.5.3 Considerations when Configuring the Delay for

Static Jitter Buffer
The lower the average and maximum delay is set, the more natural voice
transmission will sound to subscribers. However this increases the danger of
packet loss and in turn the danger of information loss and distortions. Higher
delay values mean less packets get lost, however, it takes longer until a
subscriber hears what the other subscriber is saying. Extensive delays can lead
to communication difficulties. The following diagram illustrates this:
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer

Average delay (configurable)
Received packets
Lost packets
Lower delay values:

Natural-sounding voice transmission, however some packets
are lost
Del
ay
Measured time
Higher delay values:

Voice transmission with noticeable delays, however, less packet loss
Del
ay
Measured time
Figure 6 Settings for the static jitter buffer
When the HG 3500/75 board is being generated, generous values are set with
which most installations will start without any problem. In many cases, these
values can then be reduced selectively.
2.5.4 Clock Drift with Static Jitter Buffer

With digital voice transmission in ISDN, all transmission devices operate
synchronously. In other words, the volume of voice data per time unit is absolutely
the same for the sender and the receiver. For this purpose, transmission devices
are synchronized to a common clock pulse (clock signal).
With digital voice transmission over IP, the transmission devices operate
asynchronously. 
Exception: IPDA access point with digital trunk connection can synchronize with
the clock signal.
This asynchronicity means that more or fewer packets are created per second at
the transmitting end than are expected at the receiving end. This discrepancy is
called clock drift.
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer
If more packets are created at the transmitting end than are expected by the
receiver, more packets enter the jitter buffer than intended. This leads to a
constant increase in the measured average delay. If this reaches the configured
maximum delay value, the jitter buffer adjusts itself. It skips surplus packets until
the measured average delay reverts to the set value for average delay. The entire
procedure is then restarted. The following figure illustrates the procedure:

Measured average delay
Del
ay
Measured time
Figure 7 Clock drift in static jitter buffer [transmission quicker than receipt]
If, for example, the average delay is set to 40 ms and the maximum delay to 80
ms, this means that the measured overall delay will increase at intervals by 40 ms
from the start value. The length of the interval will be determined by the clock
pulse difference of the clock pulse generators in the central system (for all HG
3500 systems) or on the HG 3575 boards as well as on the configuration data
(difference between the maximum and the average value). In the sample
configuration (40 ms delay hub) the interval is between approximately 30 and 120
minutes long.
If fewer packets are generated at the transmitting end than are expected by the
receiver, more packets enter the jitter buffer than intended. This leads to a
constant decrease in the measured average delay. If, as a result, the number of
packets located in the jitter buffer is reduced to zero, the jitter buffer adjusts itself
and resets the measured average delay to the set value for average delay by
inserting packets. The entire procedure is then restarted. The following figure
illustrates the procedure:
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer

Measured average delay
Del
ay
Measured time
Figure 8 Clock drift in static jitter buffer [transmission slower than receipt]
If, for example, the average delay has been set to 40 ms, this means that the
measured overall delay is reduced at intervals from the start value by 40 ms. The
length of the interval depends on the clock pulse difference of the clock pulse
generators in the central system (for all HG 3500 systems) or on the HG 3575
boards as well as on the configuration data (difference between the maximum
and the average values). In the sample configuration (40 ms delay hub) the
interval is between approximately 30 and 120 minutes long.
The variation in the overall delay caused by clock drift can be completely avoided
by synchronizing the components involved with a common clock pulse.
2.5.5 Minimum Delay for Adaptive Jitter Buffer

In adaptive working mode, the jitter buffer tries to keep the average delay as low
as possible. In a situation where no jitter effect occurs, the average delay drops
to a minimum. This minimum can be configured in the HG board. The average
delay, which is continuously adapted based on the current delay measured,
ranges between two values: the configurable minimum delay and the
configurable maximum delay. The following diagram illustrates this:
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer

Average delay (adaptive)
Minimum delay (configurable)
Packets
Adaptive jitter buffer: The average delay ranges

between the minimum and maximum delay and tends to
be as low as possible.
Del
ay
Measured time
Figure 9 Minimum delay for adaptive jitter buffer
Minimum and maximum delay values are still adhered to if packets are lost.
2.5.6 Packet Loss Control in Adaptive Jitter Buffer

In the case of the adaptive jitter buffer, the average delay is automatically
readjusted. The aim of this is to achieve a good balance between having the
shortest possible average delay on the one hand and the lowest possible packet
loss on the other.
You can set which of these factors is attributed more importance using the
“Preference Parameter“. Using values from 0 to 8, you can specify whether
decreasing the delay or avoiding packet loss should be prioritized when
calculating the average delay. In this case, 0 denotes “Avoid packet loss as far as
possible“ and 8 denotes “Maintain shortest possible average delay“. An average
value (4) is predefined.
Rule of thumb: setting the value to 0 results in approx. 10 ms longer average

delay and setting it to 8 results in approx. 10 ms shorter average delay than that
applicable when the average value is set to 4.
2.5.7 Parameters for Jitter Buffer Configuration

To understand the delay parameters, it is important that the values are aligned
with the compensable network jitter. As is the case for all IP gateways or
terminals, the actual transmission times for voice packets in HG 3500 and HG
3575 also fluctuate around a constant ideal value. This deviation (jitter at
transmitting end) is already taken into account during implementation.
These parameters can be set via the AMO STMIB (for HG3575) or the AMO
CGWB (for HG 3500).
A31003-H3160-S104-8-7620, 07/2014
Terms
Jitter Buffer
– Jitter Buffer Type: Select whether the jitter buffer should operate in static
or adaptive mode. In adaptive mode, the jitter buffer adjusts the average
delay according to the situation when the data is received. In this way, the
jitter buffer tries to reduce as far as possible both the delay and the
number of lost packets. In static mode, the average delay always remains
the same.
– Average Delay for Voice (msec): With this parameter you can specify
the average number of milliseconds for which an IP packet should be held
in the jitter buffer in IP-based voice transmission. In the “adaptive“ jitter
buffer, the value specified here only represents an initial value. 40 is the
value recommended for most environments.
– Maximum Delay for Voice (msec): In the “static“ jitter buffer, this
parameter is used to define how many milliseconds are allowed (before
the jitter buffer begins to regulate the data stream) for an actual measured
delay when IP packets arrive during voice transmission. In the “adaptive“
jitter buffer, the maximum number of milliseconds allowed for the average
voice delay is entered in this field. If the actual measured delay is longer,
packets are lost. 80 is the recommended value for most environments
with the static jitter buffer; 120 is the recommended value for the adaptive
jitter buffer. Either way, the value must be higher than that in the “Average
Delay for Voice (ms)“ field.
– Minimum Delay for Voice (msec): If the “adaptive“ jitter buffer was
selected, use this parameter to enter how many milliseconds are allowed
for the minimum average voice delay. This means that in every case, the
average delay value is higher than or equal to this value.
– Packet Loss / Delay Preference: In the case of adaptive jitter buffers,

you can use values from 0 to 8 in this parameter to specify whether you
would prefer packet loss or a longer delay in the case of large packet
delays. 0 denotes minimum packet loss and acceptance of delays in the
voice data stream, 8 denotes minimum delay in the voice data stream and
acceptance of packet loss. 4 is the value recommended for most
environments.
– Average Delay for Data (msec): With this parameter, you can specify the
average number of milliseconds for which an IP packet should be held in
the jitter buffer during data transfer. 60 is the value recommended for
most environments.
– Maximum Delay for Data (msec): With this parameter you can specify
the number of milliseconds allowed (before the jitter buffer begins to
regulate transmission) for an actual measured delay when IP packets
arrive during data transfer. 200 is the recommended value for most
environments. A parameter setting does not make any difference for
higher values (approx. 200 upwards) because packets then leave the
buffer as soon as they are received in full. Values under 100 ms are
possible, however they are not recommended for use.
A31003-H3160-S104-8-7620, 07/2014
Terms
Runtime and Noticeable Effects
2.6 Runtime and Noticeable Effects
2.6.1 General Information on Delay

A delay of 40-100 ms can be expected with each IP Hop (dependant on Frame
size and Jitter value).
IP Hop
An IP Hop means Encoding and Decoding one time.
2.6.2 Delay and Echo
A I P N e t wo r k
B
Says Hears Hears Says

t
One
Two
one way delay
mouth to ear
Three One
Four round trip delay Two
ECHO
Five One Three
Six Two Four Stop
Seven Three Five
Eight Stop Six
Five Seven
(four)
Six Eight
Seven
Eight
Figure 10 Delay and echo
A31003-H3160-S104-8-7620, 07/2014
Terms
Voice transmission generally requires more runtime than we are used to in

conventional telephony. Figure 10 Delay and echo contains an example
illustrating how this sounds. Here the mouth to ear delay is approximately 250 ms.
If Speaker A counts from one to eight and Speaker B says stop after he hears
three, A hears stop while he is saying eight. Obviously, selecting a number and
saying STOP during counting is not something that happens very often in real
conversation. Nevertheless, the delay effect caused by round trip delays is
noticeable in normal conversation. It often leads to collisions when the speaker
changes.
If an echo is generated on the B side (e.g. because of the 2-wire/4-wire hybrid of

analog terminal devices, also known as hybrid coil), this is noticed by the speaker,
who finds himself speaking over what he said a half a second before, for example.
With high transmission runtimes, it is therefore generally necessary to have echo-

free signals on the transmission path. With IPDA, this is achieved through active
echo cancellation in the HG 3500 and HG 3575 modules, which filters out the
signal section received from A in the send signal from B (the echo) before
transmission of the send signal from B.
2.6.3 Delay and Hands-Free Talking

A common problem is the use of hands-free equipment where there are high
transmission delays. Transmission delays are not exclusively generated by IP
transmissions. The problem can also be observed with satellite links, for example.
To suppress feedback and echo effects, the hands-free equipment lowers the
playback signal in the loudspeaker when a signal is received by the user’s own
microphone (automatic gain control). Voice activity prevents the communication
partner from being heard. This does not lead to problems in situations where
communication is disciplined and the transmission delay is low. Problems arise
when the transmission delay is high. Figure 11 Delay and hands-free talking
shows how this works. Speaker A is impatient and does not wait long enough for
an answer from speaker B before speaking again. Speaker A’s impatience
prevents him from hearing the answer from B which is retarded by the
transmission delay. This leads to misunderstandings.
The type of problems caused by transmission delays in hands-free talking are

generally linked to the type of hands-free equipment used. Half duplex hands-free
equipment (as described) is the most widely used and most sensitive equipment
available. Optiset telephones have half duplex hands-free talking. The hands-free
setting “noisy room“ is generally the best setting for connection to an IP-based
access point (in normal rooms as well).
Optipoint telephones with full duplex hands-free talking are less likely to be
affected by the phenomena described above.
A31003-H3160-S104-8-7620, 07/2014
Terms
A I P N e t wo r k
B
Says Hears Hears Says
t
We can offer you
EUR 500 per unit
Impatience, We can offer you

insecurity EUR 500 per unit
Can you deliver 10
Why does he units by Friday?
not answer?
You hesitate. Is that Can you deliver 10

too expensive? units by Friday?
Voice activity You hesitate. Is that

on the part of speaker A suppresses too expensive?
the output of the incoming signal What do you mean?
in the loudspeaker I’d prefer EUR 450
But can you deliver
by Friday?
Hello, are you still What do you mean?
there? I’d prefer EUR 450
But can you deliver
by Friday?
What by Friday? Hello, are you still
there?
Sure
What by Friday?
Sure Why don’t you just

listen to me?
What is sure?
Why don’t you just

listen to me?
Figure 11 Delay and hands-free talking
A31003-H3160-S104-8-7620, 07/2014
Terms
Voice Encryption Devices
2.7 Voice Encryption Devices

Voice encryption devices such as the optiset privacy module, for example,
transmit encrypted voice in the same way as modems. The same rules that apply
to fax and modem connections apply in this case. The changeover from
unencrypted to encrypted mode does not normally take place until there is a call,
which is why automatic pilot tone detection is particularly useful here.
A31003-H3160-S104-8-7620, 07/2014
gateways_03_arch_sys_requ.fm
Architecture and System Requirements
Prerequisites
3 Architecture and System Requirements
3.1 Prerequisites
Prior to installing IP line gateways at a customer site a network assessment is
required that will determine whether the customer’s IP network is capable of
supporting IP phones. This network assessment will analyze the IP network and
determine parameters like jitter, packet loss, available bandwidth, supported
QOS mechanisms and assess overall VoIP readiness.
3.2 Power Requirements

The HG 3500 line gateway is a HiPath 4000 peripheral card that plugs into an AP
3300 and an AP 3700 access points. However, HG 3500 cards require more than
average power due to components with high power demands (DSPs). This limits
the total number of HG 3500 cards to a maximum of 6 cards per AP 3700 IP (9
slot) and 10 cards per AP 3700 (13 slot).
3.3 Network Requirements

The HG 3500 / IPDA components place high demands on the network via which
they are coupled to their IP endpoints. Just like signaling links between the CC
and the access points, Voice-over-IP data streams are sensitive to packet
runtime, runtime variance (jitter) and packet loss.
The availability and reliability of a HG 3500 / IPDA system depends heavily on the
quality of the IP network used.
Therefore, the network must be examined prior to installation with regard to its
suitability for VoIP for the use of HG 3500 / IPDA. More details can be found in
the HiPath 4000 Network Analysis Guide.
All HiPath 4000 components must be connected to their own ports on Layer 2
switches.
Using hubs together with HiPath 4000 can cause problems. For this reason, they
are not permitted for use in corresponding VoIP scenarios. If hubs are available,
they should be replaced with a switch.
A31003-H3160-S104-8-7620, 07/2014
Network Data
In order to achieve a high Quality of Service (voice quality/real time behavior of

signaling), the support of IEEE 802.1 p/q VLAN Tagging and IETF RFC 2474
DiffServ is recommended (see Section 3.4, “Network Data”).
IMPORTANT: If an access point is connected over Wide Area Networks in which

the available bandwidth is extremely restricted, the control information
(signaling) and voice data (payload) for access points must be given priority over
other services.
Frequently, only explicitly familiar TCP/IP or UDP/IP port numbers are supported
in the customer LAN for security reasons. All others are then blocked in such
cases. Precisely which port numbers must be supported for the HG 3500
component in the network is described in Chapter 21, “IP Ports”.
IP Interface MTU
The HiPath 4000 IP interfaces use an IP interface MTU of 1500 bytes by default.
In order to ensure optimal IP network throughput, it is recommended to likewise
operate the IP network both for the IPDA LAN (Signaling/Media - Voice over IP)
and the Management LAN with a MTU of 1500 bytes.
If this is not possible, for example because of WAN routers (PPPoE, IPSEC,...)
with a smaller MTU, it is recommended to use TCP - MSS Clamping in these
routers. This router configuration results in the OpenScape 4000 software
components adapting the TCP packet size for the next TCP three-way
handshake.
IMPORTANT: This procedure applies for TCP, but not for UDP. The UDP packets
(e.g. RTP media) are generally smaller than 500 bytes however.
Exception: SIP-Q via UDP
In case of problems, it is possible to configure the IP interface MTU for CGW/

HiPath 4000 SoftGate modules by means of the module's WBM. The IP interface
MTU should not be set however to a value under 1000 bytes.
Furthermore, the HiPath 4000 software stacks generally also react to ICMP
Fragmentation Needed Packets, which then results in the packet sizes being
adapted. This procedure can lead to longer runtimes however.
3.4 Network Data

This feature is used to configure additional nodes/IP gateways in the customer
LAN. Every node/IP gateway requires configuration data which must be
coordinated with the network administration of the customer, documented and
configured precisely as agreed.
A31003-H3160-S104-8-7620, 07/2014
Network Data
The following data must be specified for every new node/IP gateway in the
customer LAN:
• IP address of the node
• Netmask for the network in which the new node is added
• Default router via which the other networks can be reached
Furthermore, the way in which Quality of Service is supported must be clarified

for all networks in which HiPath 4000 components are installed. As HiPath 4000
supports IP distributed architecture processes for controlling the Quality of
Service in a network on various protocol layers, the following must be clarified:
• Is IEEE 802.1 p/q VLAN Tagging (Layer 2) supported?

To this end, it is crucial that all network components with which a HiPath 4000
component communicates must support the standard and be configured
accordingly. If the network contains nodes (particularly switches and routers)
which do not support IEEE 802.1 p/q, VLAN tagging must remain deactivated.
The traffic type is assigned a fixed priority value.
• If DiffServ pursuant to RFC 2474 is supported, which CodePoints can be

utilized?
In the HiPath 4000 components, TOS bytes must be set to partially differing
values for the following traffic types. The default values assume DiffServ
support on the part of the network and realize the Quality of Service strategy.
For more information on the TOS baytes please refer to Section 3.4.1, “TOS
Byte”.
There are a number of other common prioritization methods, which are managed
in the affected routers:
• Prioritization based on the IP address

The entire traffic from an interface is given (identical) priority. Traffic from
IPDA components can thus be given a higher priority than other traffic by
specifying the IP address.
• Prioritization of a port (socket) range

In this case, the IPDA-specific ports (see Chapter 21, “IP Ports”) are given a
higher priority than other ports in the network.
It is essential that the signaling and payload ports be taken into account
here. This method is not recommended given the size of the port range for
payload.
• Prioritization of specific services (TCP, UDP)

Although prioritization of UDP traffic, for example, in the network would have
a positive effect on the payload, it would restrict signaling (TCP/IP). This type
of signaling is therefore NOT suitable for IPDA. It impairs system availability.
A31003-H3160-S104-8-7620, 07/2014
Network Data
3.4.1 TOS Byte

The TOS byte can be read in a number of different ways:
• Two 3-bit values for precedence and priority
• One 6-bit value as a combination of both 3-bit values (DiffServ CP)
• The entire TOS byte including two fill bits
For IPDA, the entire TOS byte is specified. The two least significant bits are
always set to zero. See also Section 2.1, “Key Words”.
Type Traffic type H TOS byte IEEE

W 802.1 p/q
Package With DiffServ Without DiffServ
Priority
Handling CodePoint
Behavior (default)
How should
Binary Dec Binary Dec
packages of this
traffic type be
handled?
TOSPL VoIP payload 1011 1000 184 0001 0000 16 5
HG 3500
(EF)
Minimal delay
Slight packet
loss
TOSSIGNL Signaling between 0110 1000 104 0001 0100 20 3
HiPath 4000
HiPath 4000 and (AF31)

access point
Minimal packet
loss
Slight delay
TOSLAN Signaling via LAN 0110 1000 104 0001 0100 20 3
(AF31)
Minimal packet
loss
Slight delay
TOSMODEM Signaling via  0111 0000 112 0001 0000 16 -
AP
Survivability (AF 32) N/A, as

connection PPP
connectio
Minimal packet
n
loss
Slight delay
Table 3 TOS values

The values for TOSSIGNL (AMO CGWB, AMO SIPCO), TOSLAN (AMO STMIB)
and TOSMODEM may not be zero. TOSLAN and TOSMODEM must be set
differently to each other. TOSPL is set in AMO CGWB, AMO SIPCO and AMO
STMIB.
A31003-H3160-S104-8-7620, 07/2014
Network Data
It is important that the required behavior (Package Handling Behavior) is

achieved in the network. The absolute numerical values for TOS and IEEE 802.1
priority are not important in this case. They are used solely for the purposes of
identifying the required Package Handling Behavior.
The values mentioned in the table are the default settings of the IP gateway
loadware (STMI/NCUI). These settings fulfill the OSCAR specifiactions.
You can change the L2 priority with

WBM > Explorers > Network Interfaces > LAN1 (LAN1) > Edit LAN1
Interface
The values for VLAN priority (layer 2) cannot be changed vai AMO. Therefore the
L2 priority for the signaling connection (CCA/CCB, AMO SIPCO) is hard coded.
IMPORTANT: 
If you change the TOS values for HG 3500 with AMO CGWB you have to reboot
the corresponding gateways with AMO BSSU.

If you change the TOS values for HG 3575 using AMO STMIB you have to an
EXEC-USSU:UPDATAP; or a REST-USSU:LTU; depending which parameter
you changed. Both commands will generate a restart of the shelf.
If you want to change the values with AMO SIPCO please do a soft restart for
CCA and CCB.
A31003-H3160-S104-8-7620, 07/2014
Network Data
Value range of the TOS values (0-255)

As of HiPath 4000 V5 R1 the calue range of the TOS values (0-255) has been
extended (see Table 4, “TOS byte correspondences”.
IMPORTANT: The column “Decimal 8-Bit” contains the values which are needed
for the AMO commands. The other columns are only for informational purposes.
DSCP-value Decimal 6-bit Decimal 8-Bit hexadecimal 6- hexadecimal 8-

Bit Bit
DSCP63 63 252 3F FC
DSCP62 62 248 3E F8
DSCP61 61 244 3D F4
DSCP60 60 240 3C F0
DSCP59 59 236 3B EC
DSCP58 58 232 3A E8
DSCP57 57 228 39 E4
CS7 56 224 38 E0
DSCP55 55 220 37 DC
DSCP54 54 216 36 D8
DSCP53 53 212 35 D4
DSCP52 52 208 34 D0
DSCP51 51 204 33 CC
DSCP50 50 200 32 C8
DSCP49 49 196 31 C4
CS6 48 192 30 C0
DSCP47 47 188 2F BC
EF 46 184 2E B8
DSCP45 45 180 2D B4
DSCP44 44 176 2C B0
DSCP43 43 172 2B AC
DSCP42 42 168 2A A8
DSCP41 41 164 29 A4
CS5 40 160 28 A0
DSCP39 39 156 27 9C
AF43 38 152 26 98
DSCP37 37 148 25 94
AF42 36 144 24 90
Table 4 TOS byte correspondences
A31003-H3160-S104-8-7620, 07/2014
Network Data
DSCP-value Decimal 6-bit Decimal 8-Bit hexadecimal 6- hexadecimal 8-

Bit Bit
DSCP35 35 140 23 8C
AF41 34 136 22 88
DSCP33 33 132 21 84
CS4 32 128 20 80
DSCP31 31 124 1F 7C
AF33 30 120 1E 78
DSCP29 29 116 1D 74
AF32 28 112 1C 70
DSCP27 27 108 1B 6C
AF31 26 104 1A 68
DSCP2 5 25 100 19 64
CS3 24 96 18 60
DSCP23 23 92 17 5C
AF23 22 88 16 58
DSCP21 21 84 15 54
AF22 20 80 14 50
DSCP19 19 76 13 4C
AF21 18 72 12 48
DSCP17 17 68 11 44
CS2 16 64 10 40
DSCP15 15 60 F 3C
AF13 14 56 E 38
DSCP13 13 52 D 34
AF12 12 48 C 30
DSCP11 11 44 B 2C
AF11 10 40 A 28
DSCP9 9 36 9 24
CS1 8 32 8 20
DSCP7 7 28 7 1C
DSCP6 6 24 6 18
DSCP5 5 20 5 14
DSCP4 4 16 4 10
DSCP3 3 12 3 C
DSCP2 2 8 2 8
DSCP1 1 4 1 4
DF 0 0 0 0
Table 4 TOS byte correspondences
A31003-H3160-S104-8-7620, 07/2014
Bandwidth Requirements
3.5 Bandwidth Requirements

The actual bandwidth per active payload connection depends on the selected
encoding algorithm, the specified sampling time and on the fact if the feature
“Signaling and Payload Encryption (SPE)” is activated.
3.5.1 Encoding
For example, the following encoding can be selected:
• G.711 (PCM) with support for Annex 1 (packet loss enhancements) and
Annex 2 (Voice Activity Detection with Comfort Noise Generation).
• G.729A voice compresses to 8Kpbs.
• G.729AB with Voice Activity Detection.
IMPORTANT: Note that there is virtually no delay introduced in generating G.711

encoding from TDM voice packets (Algorithmic Delay = 0 ms).
For more detailed information on codecs please refer to Section 2.3, “Codec
Standards”.
3.5.2 Sampling Time

Voice needs to be digitized before it can be assembled into IP packets.
For telephony applications, voice is sampled every 125 s at 8bits. It would not
make sense to package each individual 8 bit sample into an IP packet. Instead,
for G.711 encoding at least 240 8 bit samples are combined into an IP packet.
It takes 30 ms to acquire 240 voice samples.
The Sampling Time is defined as the time it takes to sample a specified number
of voice samples that are sent out in one IP packet.
It is obvious that the longer the sampling time, the smaller the IP overhead gets.
Thus, in order to minimize bandwidth, the sampling time will have to be increased.
However, increasing the sampling time will increase the overall delay!
IMPORTANT: There is always a tradeoff between minimizing the delay versus

minimizing the required bandwidth.
A31003-H3160-S104-8-7620, 07/2014
For IP line gateways the sampling time can be set between 10 ms and 90 ms
depending on codec type.
3.5.3 IP Overhead
The IP overhead includes the Real Time Protocol (RTP) header, User Datagram
Protocol (UDP) header and IP headers as well as the Ethernet framing and
additional octets for QOS Tagging. A typical IP overhead value for G.711 is 30%.
3.5.4 Required Bandwidth per Connection

Note that the bandwidth calculation is based on 70 bytes of overhead: RTP (12
bytes), UDP (8 bytes), IP (20 bytes), 802.1Q VLAN Tagging (4 Bytes), MAC (incl.
Preamble, FCS, 26 Bytes).
IMPORTANT: Bandwidth requirements assume Full Duplex operation!

When running Half Duplex, twice the bandwidth is required.
Bandwidth for active DMC master connections without SPE:
Codec Sampling Payload Payload Total Bandwidth

Time [ms] Frames per [Bytes] Bytes [Bit/s]
second
G.711 10 100,00 80 150 120000
20 50,00 160 230 92000
30 33,33 240 310 82667
40 25,00 320 390 78000
G.729AB 20 50 20 90 36000
30 33,33 30 100 26667
40 25,00 40 110 22000
60 16,67 60 130 17333
G.723 30 33.33 24 94 25067

60 16,67 48 118 15733
Table 5 Bandwidth for active DMC master connections without SPE

Bandwidth for active DMC master connections with SPE:
A31003-H3160-S104-8-7620, 07/2014
Codec Sampling Payload Payload Total Bandwidth

Time [ms] Frames per [Bytes] Bytes [Bit/s]
second
G.711 10 100,00 90 160 128000
20 50 170 240 96000
30 33,33 250 320 85333
40 25,00 330 400 80000
G.729AB 20 50 30 100 40000

30 33,33 40 110 29333
40 25,00 50 120 24000
60 16,67 70 140 18667
G.723 30 33.33 34 104 27733

60 16,67 58 128 17067
Table 6 Bandwidth for active DMC master connections with SPE

Bandwidth for master connections no longer used (without SPE):
Codec Frame Packets Packet Size [Byte] Bandwidth SID1

[kBit/s] relative
to Active
Length Length Rate Pure Data Ethernet Ethernet Ethernet
[Byte]
G.711 1 1000 ms 1,00 /s 1 71 0,6 0,7%
G.729A 2 1000 ms 1,00 /s 2 72 0,6 1,6%
G.723 4 990 ms 1,01/s 4 74 0,6 2,4%
Table 7 Bandwidth for master connections no longer used (without SPE)

1 rate between active master connections and master connections no longer used
Bandwidth for master connections no longer used (with SPE):
Codec Frame Packets Packet Size [Byte] Bandwidth SID1

[kBit/s] relative to
Active
Length Length Rate Pure Data Ethernet Ethernet Ethernet
[Byte]
G.711 1 1000 ms 1,00 /s 11 81 0,6 0,8%
G.729A 2 1000 ms 1,00 /s 12 82 0,7 1,6%
G.723 4 990 ms 1,01/s 14 84 0,7 2,4%
Table 8 Bandwidth for master connections no longer used (with SPE)

1 rate between active master connections and master connections no longer used
A31003-H3160-S104-8-7620, 07/2014
3.5.5 Voice Activity Detection (VAD)

Voice activity detection conserves bandwidth in the IP network during pauses in
speech and can further reduce the required network bandwidth from 50% to 75%
(see Section 5.3, “Voice Activity Detection (VAD)” for more details).
Figure 12 VoIP Bandwidth Reduction Sequence
3.5.6 DMC Considerations

Whenever a DMC connection is established, a “Master Connection” is setup as
well.
The master connection is following the same path as the signaling through all the
gateways between to IP clients.
The master connection ensures that the necessary resources are always
available whenever a feature is invoked that results in a multi party call (e.g.
conference). There is also no delay for invoking these types of features because
the connection is already setup.
However, there are drawbacks to the master connection concept as well:
• Additional bandwidth is required for sustaining the master connection
• Depending on the configuration significant delays and multiple hops can

occur between IP clients when voice payload is using the master connection.
Especially when IP end points are located on different IP Access Points on IP
connected systems, delays may increase beyond acceptable levels.
In Figure 13 DMC and Master Connection the DMC and Master Connection is
shown between two IP networked HiPath 4000 systems for a call between two IP
clients (one on each system).
A31003-H3160-S104-8-7620, 07/2014
B Channels
Figure 13 DMC and Master Connection
Enabling VAD will reduce the required bandwidth on the master connection to
negligible levels.
Note that delays for each TDM to IP conversion accumulate. In the example
above the master connection goes through 3 hops which will result in
approximately 200ms end to end delay assuming G.711 encoding with 30ms
sampling time and a high quality network (20ms delay). The DMC connection
goes only through one hop resulting in an end to end delay of about 80ms.
For more details please refer to Section 5.1, “Direct Media Connection (DMC)”.
3.6 B Channels
The following table provides an overview of the number of available B channels
that are dependent on enabled features.
Relative STMI2/NCUI2+ STMI4/NCUI4

2 DSP 4 DSP 2 DSP 5 DSP
Standards 100% 100% 100% 60 120 60 120
QDC 56 112 60 120
SRTP 75% 83% 100% 45 90 50 120
QDC+SRTP 42 84 50 120
DMC 75% 83% 83% 45 90 50 100
QDC+DMC 42 84 50 100
DMC+SRTP 56% 69% 83% 32 63 40 100
QDC+DMC+SRTP 30 60 40 100
Table 9 Number of B channels dependent on enabled features
A31003-H3160-S104-8-7620, 07/2014
B Channels
Important Notes for QDC

QDC is activated on the gateway via WBM and needs additional performance
resources.
QDC is not automatically considered for channel reduction. Therefore the

number of channels has to be adapted manual (depending on the type of the
board) to the values mentioned in the table above when QDC is activated. If no
adaption takes place performance problems will occur.
3.6.1 B Channel Configuration
3.6.1.1 AMO BFDAT
Using the AMO BFDAT, the profile of the board is defined with a maximum
number of B channels.
• ADD-BFDAT, parameter BRDBCHL

The parameter BRDBCHL determines if a block for a board with 60 or 120 b
channels will be configured.
• ADD-BFDAT, parameter FUNCTION

With the parameter FUNCTION you can configure the functions of the
common gateway (i.e. HG 3500, HG 3530, etc.).
• CHANGE-BFDAT, parameter BCHLCNT

With the parameter BCHLCNT you can configure the maximum number of b
channels per function. This value must not be higher than the maximum
number of b channels possible for this function (see Section 3.6.1.2, “AMO
BCSU”, parameter BCHLCNT).
3.6.1.2 AMO BCSU
The profile configured with AMO BFDAT (maximum number of b channels

(BRDBCHL) and configured functions (FUNCTION)) is evaluated by AMO
BCSU. Additionally the activated features in the system (i.e. DMC, SPE) will be
considered. An automatich b channeld reduction will be performed (see Section
3.6.2, “Automatic b channel reduction”).
With DISPLAY-BCSU the following information can be found:
• How many b channels are available on the board (BCHANNELS).
• How many b channels have been configured wit AMO BFDAT per function
(BCHANNELS).
A31003-H3160-S104-8-7620, 07/2014
B Channels
• How many b channels are possible per function (BCHLCNT). The parameter
BCHLCNT depends on what feature has been activated (see Section 3.6, “B
Channels”). The value in parameter BCHLCNT can be lower than the
configured number of b channles for this function in AMO BFDAT. But only the
amount of b channels of parameter BCHLCNT are available for the function.
In the case of bandwidth problems, etc. the current value of the B channels that
can be used for each configured function must be reduced. This can be done in
AMO BCSU with the b channel parameters (i.e. BCHL3530, BCHLSIP,
BCHL3550).
3.6.2 Automatic b channel reduction

Using the features for signaling and payload encryption (SPE) and also DMC,
automatic b channel reduction is performed, i.e. the current values set are
reduced by a fixed percentage. This percentage depends on the hardware used.
IMPORTANT: The automatic b channel reduction is not performed with the

feature QDC. This b channel reduction has to be done manually referring to Table
9, “Number of B channels dependent on enabled features”.
Board Maximum Reduction in % Reduction in b

number of channels
b channels
DMC SPE DMC SPE
NCUI2+ (Q2305-X35) 60 25 25 15 15
NCUI2+ (2305-X40) 120 25 25 30 30
NCUI4 (Q2324-X) 60 17 17 10 10
NCUI4 (Q2324-X10) 120 17 0 20 0
STMI2 (Q2316-X) 60 25 25 15 15
STMI2 (Q2316-X10) 120 25 25 30 30
STMI4 (Q2324-X500) 60 17 17 10 10
STMI4 (Q2324-X510) 120 17 0 20 0
Table 10 Number of B channels depending on SPE and DMC

This reduction is not only calculated on board level but on function level. This
means that the percentage values from above will be calculated per configured
function.
Examples for single feature support (STMI2/STMI4):

1. DMC is activated for HG 3550 on Q2324-X510
DMC activated on Q2324-X510: reduction of the b channels of 17% (= minus
20 b channels)
A31003-H3160-S104-8-7620, 07/2014
B Channels
=> Maximum number of available b-channels: 120-20=100
2. SPE and DMC is activated for HG 3550 on Q2316-X.

SPE activated on Q2316-X: reduction of the b channels of 25% (= minus 15
b channels)
=> 60-15=45
DMC additionally activated on Q2316-X: reduction of the b channels of 25%
(of the maximum number of available b channels / depending on the board
and/or number of DSPs = minus 15 b channels)
=> Maximum number of available b-channels: 45-15=30
Example for multiple feature support (STMI2/STMI4):

1. DMC is activated for 2 HG 3550 circuits with 40 b-channels on Q2324-X500.
The remaining 20 b-channels are configured for HG 3530.
SPE activated on Q2324-X500 for HG 3550: reduction of the b channels of
17% (of 40 b channels = minus 7 b channels )
=> Maximum number of available b-channels for HG 3550: 40-7=33
The HG 3530 gateway cannot act as DMC endpoint. Therefore the 20 b
channels won’t be reduced for HG 3530.
2. SPE is activated for 2 HG 3550 circuits with 40 b-channels and HG 3530 for
20 b channels on Q2324-X500.
17% (of 40 b channels = minus 7 b channels)
17% (of 20 b channels = minus 3 b channels)
These reduced b-channel values are the upper limit for path selection.
The B channel number increases appropriately when features are deactivated.
Summary:
In the AMO BFDAT, only the maximum number of B channels can be

configured. Using the AMO BCSU, the number of currently available B
channels can be displayed and the B channels configured.
The following tables provide an overview of the number of available B channels

that are dependent on enabled features.
A31003-H3160-S104-8-7620, 07/2014
Traffic Considerations
3.6.3 Displaying the B Channels currently Available/

Configured (possible IP-Based Connections)
The total number of B channels currently in use is shown as usual in the AMO
BCSU. The number of B channels is configured in AMO BSCU with the
corresponding B channel parameter for each function (BCHL3530, BCHLSIP,
BCHL3550, BCHLWAML and BCHL3570). The AMO BFDAT includes the
parameter BRDBCHL. This defines the maximum number of B channels for the
board (60 or 120 B channels).
Using the AMO BCSU, you can query the number of B channels available for the
common gateway board. The AMO UCSU must be used for configured HG3575
boards.
IMPORTANT: Determination of the B channel values differs for HG 3500 and HG

3575.
You can check the channels or bandwidth used with the AMO GKTOP following
appropriate configuration.
DISPLAY-BCSU:TAB,1,<LTU Number>; command shows 3 b-channel

values:
• The maximum number of B-channels supported by the board,
• the number of used b-channels per function and
• the maximum possible number of b-channels per function.
3.7 Traffic Considerations

From a trafficking point of view, HG 3500 IP line gateways can be treated like a
trunk with either 60 or 120 connections. The number of connections required
depends on the number of IP phones configured per HG 3500 and the traffic
(C.C.S.) values of these phones. Using a standard ErlangB calculation allows
determining the number of trunks/connections that are required on each gateway
for a specific configuration.
The tools use a simplified approach and allow 240 standard users and 60/120
high traffic (e.g. call center agents) users on each gateway type. Note that you
can mix and match standard and high traffic users but you will be limited to 60/
120 users per gateway total. This ensures that call center agents will always be
able to seize a line.
Capacities
A maximum of 240 IP clients can be configured per HG 3500 gateway.
A31003-H3160-S104-8-7620, 07/2014
Typically a 60 connections gateway is sufficient to serve 240 at 6 C.C.S.. In case

the users creating a higher amount of traffic, then a 120 connections gateway will
be required.
Call center agents are typically trafficked at 32 C.C.S. and thus require a
connection on the gateway for each agents. This will limit the number of call
center agents to 60 or 120 depending on the HG 3500 type (60/120 connections).
IMPORTANT: Mixing of regular users and call center agents on the same card is
possible. However, in order to guarantee connection availability to call center
agents at all times, regular users will be trafficked at 1 Erlang (36 C.C.S.)
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
gateways_04_overview.fm
Supported Gateways
HG 3500 (Common Gateway)
4 Supported Gateways
The gateways HG 3500 (Common Gateway) and HG 3575 are supported in
HiPath 4000 V6.
4.1 HG 3500 (Common Gateway)
4.1.1 General Information

HG 3500 is supported with the following boards:
• STMI2 (Q2316-X and Q2316-X10)
• STMI4 (Q2324-X500 and Q2324-X510)
The HG 3500 replaces the following gateways:
• HG 3530 (HFA subscriber)
• HG 3540 (SIP Trunking (native & SIP-Q) and SIP subscriber)
• HG 3550 (IP Trunking)
• HG 3570 (IPDA (host side) - Master and IPDA (host side) - DMC)
With the HG 35000 gateway different sub features (e.g. trunking and IPDA) can
be used in parallel on a board (Multiple Feature Support (MFS)). The gateway
can also be used as Single Feature Configuration.
The HiPath Feature Access (HFA) standby concept will be made available for
other functions.
IMPORTANT: Restriction: Only one trunking protocol may be configured for

each board. There are no restrictions on interworking with other functions.
Configuration example for Multiple Feature Support: see Chapter 16, “Multiple
Feature Support Configuration at the Common Gateway (Example)”.
Examples of single feature configuration can be found in the documents:
• HiPath Feature Access (HFA)
• Access Point Emergency (APE)
• SIP Connectivity > Chapter 5, “Configuration of SIP-Q-Trunking / Native SIP

Trunking” or
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
• H323-/H323-Annex-trunking
4.1.2 Board Replacement

To replace an STMI board please note the following:
• Replace a “small“ STMI with a “small“ STMI: no problem
• Replace a “large“ STMI with a “large“ STMI: no problem
• Replace a “small“ STMI with a “large“ STMI: no problem
• Replace a “large“ STMI with a “small“ STMI: only works if not more than 60 b-
channels are used
Procedure:
• Change the board.
• It is not necessary to delete all circuits on the module and the module itself,
but rather to change the part number with CHANGE-BCSU (if necessary).
CHANGE-
BCSU:TYPE=PARTNO,LTG=<ltg>,LTU=<ltu>,SLOT=<slot>,PARTNO1=<par
t number of board to be changed>,PARTNO2=<part number of new
board>;
• Restart the board with
RESTART-BSSU:ADDRTYPE=PEN,LTG=<ltg>,LTU=<ltu>,SLOT=<slot>;
4.1.3 Feature Capacities
IMPORTANT: Information on feature capacities for both HG 3500 and HG 3575

see Chapter 5, “Features and Restrictions”.
• The HG 3500 gateway has the capacity to convert 60/120 connections into
Fast Ethernet packets and provide TDM to IP conversion for 60/120
concurrent calls.
• HG 3500 gateways can be configured as a standby gateways providing

backup capabilities in case of individual gateway failure.
More detailed information on standby gateways
One or multiple standby HG 3500 IP line gateways can be defined in the

system that will take over in case any of the installed line gateways fails.
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
This concept is very efficient and cost effective because a single gateway can
protect multiple gateways against failure. However, a single gateway cannot
protect against multiple gateways failing simultaneously, which is highly
unlikely.
In case of a failure, the system will reprogram a standby gateway with the
parameters of the failed gateway which will enable the IP clients to re-login
and resume standard operation.
IP phones will automatically register with the activated standby gateway and
no administrative action is required. Note that users keep the same features
and extensions while operating off the standby gateway.
Figure 14 HG 3500 Standby Gateway Operation
Standby gateways can be located in the host system and/or on an IP Access

point. The only requirement is that all active and standby line gateways have
to reside in the same local IP subnet.
IMPORTANT: Standby gateways and IP clients have to reside within the

same system!
E.g.: a standby gateway located in one system cannot control IP clients
controlled normally by a gateway located in another system.
Standby gateways at IP Access Points will not protect IP users at the host
against a host failure because failures at higher levels (e.g. shelf, AP, host or
power failures) will not automatically trigger a switchover.
For configuration purposes please refor to Chapter 10, “Standby Board HG

3500”.
• The HG 3500 gateway supports secondary gateways that provide full

redundancy to IP subscribers. Providing full redundancy for IP clients via
secondary gateways will protect against higher level failures, like entire
Access Point or host failures.
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
More detailed information on secondary gateways
In order to protect against higher level failures (e.g. Access Point, host
failures) secondary gateways can be added to the system. A secondary
gateway is an additional, fully configured gateway for an IP client located
anywhere within a HiPath 4000 system. Note that each IP user that is backed
up via a secondary gateway will have 2 extensions, e.g. x1333 on the primary
gateway and extension x5333 on the secondary gateway.
In case communication to the primary gateway is lost (e.g. due to a shelf or
host failure), the IP phone will attempt to register with the secondary gateway.
As long as the secondary gateway is operational and IP connectivity is
available, all phones backed up with secondary gateways will register with
their secondary gateway and will be fully operational.
While registered with the secondary gateway the users will have all features
available that have been enabled on the secondary extension. Incoming calls
terminating on the primary extension will be automatically forwarded to the
secondary extension using a new feature called “Alternate Routing on Error”.
Figure 15 HG 3500 Secondary Gateway Operation
In order to minimize the number of secondary gateways and additional trunks

required for operating in failure mode, the following measures can be taken:
• Secondary gateways can be configured with a higher blocking rate, which

will limit the number of IP users that can make concurrent calls.
• Minimize the additional trunk required for secondary gateways via

“undertrunking”.
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
Note that these measures are entirely optional and up to the customer’s
preference. However, it may be a reasonable approach to limit resources
(and thus cost) for operation in failure mode because this is a scenario that is
very unlikely to become reality.
IMPORTANT: Secondary gateways and IP clients have to reside within the

same system!
Secondary gateways can automatically backup any IP user as long as the
secondary gateway is operational and IP connectivity between the IP client
and the gateway is available.
• The HG 3500 gateway supports QoS. VLAN-tagging according IEEE 802.1p/

q on Layer 2 as well as DiffServ (defined in RFC 2474) on the IP Layer have
been implemented in order to provide the best possible voice quality using an
IP network.
Of course all switches and routers in the customer’s IP network must support
IEEE 802.1p/q and/or DiffServ prioritization in order to take advantage of
these mechanisms.
• The HG 3500 gateway supports “secondary clients”.
More detailed information on secondary clients
• Secondary clients are soft clients configured with the same phone
number as a regular IP phone.
• Secondary Clients do not require a ComScendo license.
• Secondary Clients require a soft clients SW license.

The standard H225 signaling port is 1720 and this port is used at the soft
client to establish calls from the board to the soft client. For the soft client it
might be necessary to use a different port. In the case that an other H323
application is running in parallel to the soft client it is possible to configure a
different H225 signaling port on the soft client. The soft client informs the HG
3500 at registration time and the HG 3500 will use this port for call
establishment.
The soft client can be used as a non standard VPN client. In this configuration
the HG 3500 checks the delivered IP address and the real address on the
connected CorNetTC socket and informs the soft client about its real IP
address when these 2 addresses are different..
Benefits of Secondary Clients:
• Secondary clients provide remote access to all HiPath 4000 features.
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
• Starting the secondary client on a PC from any location automatically

logs off the office IP phone (associated by the same phone number) and
provides the same feature set and class or service to the end-user as the
office IP phone.
• After the remote user returns to the office, the IP phone will still be in the
logged off state and the user is prompted to start the phone. This will put
the IP phone into a normal operation mode until the IP phone is logged
off again by an activation of the associated soft client.
• “Overbooking” is possible, meaning that more IP phones per HG 3500

gateway can be configured than there are available connections (maximum
of 240 subscribers).
More detailed information on “Overbooking”
For overbooking, more stations (LINECNT) are configured than the number
of actual subscribers (BCHLCNT). The actual number of subscribers is
configured for the B channels.
Example:
Five employees are working at a warehouse. However, the warehouse is big
enough to house 10 terminals. As only five employees can simultaneously
make and receive calls, only five B channels are required.
Parameters: LINECNT=10, BCHLCNT=5
• All IP phones do support DHCP and are supported in DHCP mode via the HG
3500 gateway. Note that a DHCP server has to be configured in the IP
network; otherwise static IP addresses are required for all clients.
• The connection of analog devices via a HiPath AP 1120 analog gateway

is supported. For more details please refer to the E-Doku pages in the intranet
(http://apps.g-dms.com:8081/edoku/jsp/
searchresult_v2.jsp?edokutype=&search_mode=product&product=AP%201
120&product_version_main=&product_version_sub=&search_term_type=all
&term=&sort_result=title&docclass=&language=&checkdate=&lang=en).
• Full user mobility is supported within a single system and networked

systems.
• The HG 3500 gateway is supported in all IP distributed Access Points.
4.1.4 Restrictions
• CQR Viewer
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
HG 3575
The CQR Viewer application is only supported for HFA

(FUNCTION=HG3530) and IPDA (FUNCTION=HG3570), not for trunking
(FUNCTION=HG3550).
• The HG 3500 supports only phone adapters that do not require their own B-
channel.
The following adapters are not supported:
– phone-adapter,
– a/b-Adapter,
– S0-adapter
– V.24-Adapter
• Autoset Relocate, Teleworking V2.6 and Workstation Protocol are not

supported with HG 3500.
• HG 3500 line gateways do not operate in a load-sharing mode - there is a

fixed assignment of the IP phones to one HG 3500 gateway.
• The HG 3500 integrated gateway does not interoperate with 3rd party (e.g.
H.323/H.450 or SIP compatible) IP phones/clients.
• The HG 3500 integrated gateway requires a static IP address.
• NTP (Network Time Protocol) is not supported on the HG 3500 because there
is no real-time clock chip on the gateway card.
4.2 HG 3575

HG 3575 is supported with the following boards:
• NCUI2+ (Q2305-X35 and Q2305-X40)
• NCUI4 (Q2324-X and Q2324-X10)
In contrast to HG 3500, there is no standby concept for HG 3575.
4.2.2 Exchanging Boards

HiPath 4000 - Access Point
1. Deactivate the shelf
DEACTIVATE-USSU:LTG=1,LTU=17;
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
HG 3575
2. Remove the old board, insert the new one
If the new board has the same part number as the old one, proceed directly to
Item 6. “Activate the shelf”.
3. Delete the AP
EXEC-USSU:ART=DELAP,LTU=17;
4. Assign the new part number to the shelf
CHANGE-UCSU:UNIT=AP,LTG=1,LTU=17,LTPARTNO=Q2305-X10;
5. Configure the AP
EXEC-USSU:MODE=CONFAP,LTU=17;
6. Activate the shelf
ACTIVATE-USSU:UNIT=LTG,LTG=1,LTU=17;
HiPath 4000 - Switch

CHANGE-STMIB:MTYPE=NCUI2,LTU=18,SLOT=99,TYPE=GLOBAL,PATTERN=213;
CHANGE-
STMIB:MTYP=NCUI2,LTU=18,TYPE=IFDATA,VLAN=NO,TOSLAN=72,TOSMODEM=8
0,VLANID=0,BITRATE=100MBFD;
CHANGE-
STMIB:MTYP=NCUI2,LTU=18,TYPE=SERVIF,LOGINTRM="TRM",LOGINPPP="PPP
";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=ASC,TOSPL=48=PRIO=PRIO1,CODEC=G711
,VAD=NO,RTP="30";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=ASC,PRIO=PRIO2,CODEC=G729,VAD=NO,R
TP="20";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=ASC,PRIO=PRIO3,CODEC=NONE,VAD=NO,R
TP="20";
CHANGE-
TP="20";
CHANGE-
TP="20";
CHANGE-
TP="20";
CHANGE-
TP="20";
CHA-
STMIB:MYTPE=NCUI2,LTU=18,TYPE=JB,AVGDLY=40,MAXDLYV=120,MINDLYV=2
0,PACKLOSS=4,AVGDLYG=60,MAXDLYD=200,JBMODE=1;
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
HG 3575
CHA-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=SIGQOS,BANDW=0,MAXRTD=0,MINTHRPT=0
,SIGPTHSW=STD,QOSSTAT=NO;
CHA-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=H323,Q931T1=50,Q931T2=500,GWNAME="
HG3575-2";
CHA-STMIB:MTYPE=NCUI2,LTU=18,TYPE=DMCDATA,DMCALLWD=NO,DMCCONN=0;
CHA-STMIB:MYTPE=NCUI2,LTU=18,TYPE=SNMP,CS1="public";
CHA-STMIB:MYTPE=NCUI2,LTU=18,TYPE=WBMDATA,LOGINWBM="HP4K-
DEVEL",ROLE=ENGR;
SU",ROLE=SU;
ADMIN",ROLE=ADMIN;
READER",ROLE=READONLY;
CHA-STMIB:MYTPE=NCUI2,LTU=18,TYPE=GWSECTOR,GWSECTNO=0;
CHA-
STMIB:MYTPE=NCUI2,LTU=18,TYPE=DLSDATA,DLSPORT=10444,DLSACPAS=NO;
WBM configuration
Complete additional settings via WBM.
CLI configuration
So that a connection can be established again to the switch, the IP addresses in
the new board must be configured via CLI.
A31003-H3160-S104-8-7620, 07/2014
Supported Gateways
HG 3575
A31003-H3160-S104-8-7620, 07/2014
gateways_05_hg35xxv4_features.fm
Features and Restrictions
Direct Media Connection (DMC)
5 Features and Restrictions

The following features are supported on HG 3500 and HG 3575. For features
concerning HG 3500 only please refer to Section 4.1.3, “Feature Capacities”.
5.1 Direct Media Connection (DMC)

The HG 35xx gateways support Direct Media Connections (DMC).
More detailed information on Direct Media Connections
The HG 35xx gateways support Direct Media Connections (DMC also referred to
as peer-to-peer) between two IP phones or an IP phone and an IP board like
another HG 3500 or HG 3575. Payload between two DMC endpoints (DMC
endpoints = IP phone, HG 3500/3575) is switched entirely in the IP network
without involvement or the TDM switching matrix. This ensures highest quality
voice and minimal delays because only a single hop (TDM to IP to TDM
conversion) is required.
IMPORTANT: Note that invoking any feature that results in a multi party call
(more than 2 parties) will route the payload through all gateways in the payload
path. This may result in undesirable delays in certain scenarios (see Section
3.5.6, “DMC Considerations” for more details).
Bandwidth is required for the master connection in addition to the DMC

connection. The required bandwidth for the master connection can virtually be
eliminated by using VAD for the IP clients. In case VAD cannot be enabled then
twice the bandwidth is required.
For more information on DMC and bandwidth please refer to Section 3.5.6, “DMC
Considerations”.
5.2 Voice Compression

The HG 35xx gateways support voice compression follwoing standard G.711A
encoding at 64Kbps. Compression according to G.729A and G.729AB is
supported as well. Also supported codecs are G.711U, G.723 (only for HG 3500),
G.729 and G.729B.
A31003-H3160-S104-8-7620, 07/2014
Voice Compression
Of course the actual bandwidth requirements per connection depend on the

added IP overhead and various other settings (see Section 3.5.4, “Required
Bandwidth per Connection”).
IMPORTANT: Note that the voice compression as well as the gateway function-
ality is performed on DSP modules.
More detailed information on voice compression
Voice compression uses complex algorithms to reduce the bandwidth of the voice
signal, for example G.729, to an eighth of the bandwidth required by the original
PCM signal. Impairment of voice quality is only minimal in this case.
Voice compression can be problematic when it is applied a number of times in

succession. In other words, the original PCM signal is compressed using a
specific method, transmitted and then expanded back to a standard PCM signal.
Then the whole procedure is repeated on another section. In the worst case
scenario, with another procedure. Applying voice compression a number of
times, particularly using different compression methods, severely impairs voice
clarity and in the worst case scenario it can result in unintelligibility.
The linking of compressed transmission segments - particularly using different

methods - must therefore be avoided wherever possible.
Given that all digital speech memory systems for announcements, voicemail etc.
also compress speech, this type of equipment must be monitored carefully when
used with compressed transmission paths.
Within the HiPath 4000 system, connections to announcement/music on hold

devices as well as to conference units are configured without compression in
order to guarantee undistorted music or good voice clarity for conferences.
The factors specified in association with voice compression, such as

compression to an eighth of the originally required (uncompressed) bandwidth,
for example, always refer to the actual voice data. If this data is transferred using
IP, the IP packaging, the “protocol overhead“, must also be taken into account.
The voice data to be transferred is reduced by the specified factor by means of
compression, but the overhead remains the same. The bandwidth required in the
IP network is therefore never reduced by the specified compression factor, but
instead by a lot less. Always take the values specified in Chapter 3, “Load
Calculation” in the document “IP Distributed Architecture (IPDA)“ into account
when dimensioning the bandwidth.
A31003-H3160-S104-8-7620, 07/2014
Voice Activity Detection (VAD)
5.3 Voice Activity Detection (VAD)

The HG 35xx gateways support VAD (Voice Activity Detection).
More detailed information on Voice Activity Detection (VAD)
Voice Activity Detection (VAD) serves to save bandwidth in the IP network during
pauses in speech.
Based on the knowledge that only one partner usually speaks at a time, while the
other partner listens, the bandwidth seized during a call is only really used in one
direction (speaking station -> listening station). In the other direction (listening
station -> speaking station), only ambient noise and “silence“ are transmitted.
Voice activity detection makes use of this knowledge, interrupts the data
transmission and drastically reduces the data rate as soon as silence is detected.
As soon as voice activity is detected again, transmission for that direction is
immediately re-established (with full bandwidth).
If NOTHING is transmitted on a route, the receiving end generally tends to identify

the absence of background noise as line failure and therefore as undesirable.
Therefore, depending on the codec used, highly compressed background noise
is sometimes transmitted or noise is supplied.
The problem with VAD is the difficulty in distinguishing between ambient noise
and silence in transmission. Ambient noise in the room should fall under the
category of silence, but softly spoken words should be categorized as voice. The
impairment (or in the worst case, truncation) of the beginning or end of voice
activity in the transition area is unavoidable.
Linking is also a problem with VAD. Using VAD on multiple transmission paths in
succession can increase impairment effects. The linking of transmission paths
with VAD must therefore be avoided.
The resulting bandwidth reduction is in the range of 50% to 75%.
The VAD classmark is deactivated by default, but can be activated at any time for
voice connections.
IMPORTANT: VAD must not be activated in the case of fax, modem and digital
data connections!
5.4 Comfort Noise Generation (CNG)

The HG 35xx gateways support CNG (Comfort Noise Generation).
A31003-H3160-S104-8-7620, 07/2014
Echo Cancellation
While using VAD, the DSP at the destination emulates background noise from the
source side, preventing the perception that a call is disconnected.
5.5 Echo Cancellation

The HG 35xx gateways support on board echo cancellation (performed on the
on-board DSP modules) compliant with the ITU-T G.168 standard.
More detailed information on echo cancellation
Echo arises at all analog 2-wire/4-wire hybrids, e.g. in the hybrid coil of an analog
telephone, as well as through acoustic over-coupling of speaker and microphone
in the recipient’s handset.
If the runtime between the generation of an audible signal and the manifestation
of the echo at the speaker (Round Trip Delay) is very slight, the echo has no
interfering effect. However, the greater this runtime, the greater the disturbance
of the echo. The runtimes in the case of IP transmission are very high. Thus,
echoes are always perceived as extremely disturbing. Therefore, it is important
that all signals are free of echo prior to being transmitted in the IP network. The
resulting effects of delay and echo are explained in detail in Section 2.6.2, “Delay
and Echo”.
Echo cancellation suppresses the echo by filtering it out of the data stream. Echo
cancellation should always be used as close to the source of the echo as
possible.
The following example is intended to clarify this:
• Subscriber A is connected to Subscriber B via an IP route.
• The terminal device of Subscriber B generates an echo of the signal of

Subscriber A.
• The echo is to be suppressed near the source, i.e. in the vicinity of Subscriber
B, so that the signal from B to A is free of echo before being transmitted
across the IP route.
Echo cancellation (echo suppression) is a very complex operation in digital signal

processing, which only has a minimal effect on the transmitted wanted signal
(without echo).
Echo cancellation is configured automatically for all circuits, but can be

deactivated.
Analog modems and fax machines use complicated phase modulation

procedures for data transfer which can be affected by interference caused by
echo cancellation.
A31003-H3160-S104-8-7620, 07/2014
Redundant LAN Interface
5.6 Redundant LAN Interface

The feature “Redundant LAN Interface” described in the document "IP Distributed
Architecture (IPDA)” Chapter 6, “Information for network administrators” is
generally supported. However, if the WAML function is configured, this feature is
not supported.
5.7 Security
5.7.1 Access for Administration

Authentication methods are used for access to administration.
In order to protect all files and debug info on the HG 3500, access is only possible
via https and SSH.
5.7.2 Access to SNMP

The acces to SNMP is restricted via read and write Community strings. These
Community strings can be configured with the WBM > Maintenance > SNMP >
Communities.
5.7.3 Security in CorNetTC Registration

The log-on between the IP phones and HG 3500 is secured via SHA1. The
payload and signaling connections are not encrypted.
5.7.4 H.235 Security

When this feature gets activated all messages between the HG 3500 and the IP
phones are authenticated. Authenticated messages will contain a Crypto Token
element. As Crypto Token handling requires precise time and therefore the local
system time is distributed cyclic to the IP endpoints.
For more details on configuration please refer to Section 14.8, “TYPE H235DATA
- H.235-Security”.
A31003-H3160-S104-8-7620, 07/2014
Resource Manager (RM)
5.7.5 Connecting IP Gateways to the Internet or via

External Providers
The connection of IP gateways to the Internet or external providers reveals a
security vulnerability ("insecure" LAN/WAN). An IP or MAC address filter must be
set to combat this problem. This can be done via the board’s WBM.
WBM > Explorers > Security > MAC Address Filtering or WBM > Explorers
> Security > IP Address Filtering.
For a detailed description, see "HiPath 4000 V6, Gateways HG 3500 and HG
3575, Administrator Documentation" (http://apps.g-dms.com:8081/techdoc/en/
P31003H3160M1000100A9/index.htm).
5.8 Resource Manager (RM)
IMPORTANT: The Resource Manager is released for use in standalone systems

with HFA and IPDA.
In a real, complex IP network the available bandwidth is typically not uniform in

all sectors.
The Resource Manager (RM) can administer and monitor the bandwidth for up to
800 sectors in a given IP network.
The RM updates a cluster matrix whenever a call is setup or torn down. The
matrix allows determination whether there is a resource shortage in any of the
involved sectors. Based on the configured bandwidth and the actual bandwidth a
call is either allowed to complete or rejected.
The RM calculates real bandwidth, taking compression settings, DMC, FAX, etc.
into account.
For more information on the resource manager please refer to Chapter 17,
“Resource Manager Functionality”.
A31003-H3160-S104-8-7620, 07/2014
Restrictions
5.9 Restrictions
5.9.1 Loadware-Update or Reset of the Board

Problem description:
An HG 3500 is configured as a SIP trunking gateway. The parameters for the
connection to the Web Based Management of the board (AMO CGWB,
parameter MGNTIP and MGNTPN) and the backup server (AMO CGWB,
parameter BUSIP and BUSPN) have to be configured.
After a reset of the board or after a loadware update the IP addresses (MGNTIP
and BUSIP) are restored but not the port numbers (MGNTPN and BUSPN).
These parameter values are set to the default value (in both cases „0“). Therefore
a connection to the backup server cannot be established anymore. The needed
configuration data for SIP trunking that has been configured in the WBM and has
been saved on the backup server cannot be restored. The SIp trunking
connection canniot be re-established again.
Solutions:
Check parameter in AMO CGWB and configure it again:
CHANGE-
CGWB:MTYPE=CGW,LTU=<number>,SLOT=<number>,TYPE=MGNTDATA,MGNTPN=8
000,BUSPN=443;
Or save the configuration data in the local falsh of the board during installation of
the board:
WBM > Maintenance > Actions > Automatic Actions > Save Local
Configuration for Upgrade
For a detailed description, see "HiPath 4000 V6, Gateways HG 3500 and HG
3575, Administrator Documentation" (http://apps.g-dms.com:8081/techdoc/en/
P31003H3160M1000100A9/index.htm).
5.9.2 Possible IP hops
IMPORTANT: More than 3 IP hops can lead to restrictions in a Voice over IP

system, i.e. the delay can be too long and the result is poor speech quality or
malfunctioning features.
A31003-H3160-S104-8-7620, 07/2014
Restrictions
A31003-H3160-S104-8-7620, 07/2014
gateways_06_com_matrix.fm
Communication Matrix
6 Communication Matrix
Legend for the follwoing tables:
--- Not possible

x Possible
HiPath 4000 V6
HG 3500
H323 SIP-Q Native DMC HFA-
SIP Mobili
ty
H323 --- --- --- --- ---
SIP --- --- --- --- ---
HiPath HG 3550
4000 V1.1 Native SIP --- --- --- --- ---
V1.0 DMC --- --- --- --- ---
HFA-Mobility --- --- --- --- ---
H323 --- --- --- --- ---

SIP --- --- --- --- ---
HG 3550
V1.1 Native SIP --- --- --- --- ---
DMC --- --- --- --- ---
HiPath
4000 HFA-Mobility --- --- --- --- ---
V2.0 H323 x --- --- x x
SIP --- --- --- --- x
HG 3550
V2.0 Native SIP --- --- --- --- ---
DMC x --- --- x ---
HFA-Mobility x --- --- --- x
Table 11 Networking with HiPath 4000 V6
A31003-H3160-S104-8-7620, 07/2014
gateways_06_com_matrix.fm
Communication Matrix
HiPath 4000 V6
HG 3500
H323 SIP-Q Native DMC HFA-
SIP Mobili
ty
H323 --- --- --- --- ---
SIP --- --- --- --- ---
HG 3550
V1.1 Native SIP --- --- --- --- ---
DMC --- --- --- --- ---
HiPath
4000 HFA-Mobility --- --- --- --- ---
V3.0 H323 x --- --- x x
SIP --- x --- x x
HG 3550
V2.0 Native SIP --- --- x --- ---
DMC x x --- x ---
HFA-Mobility x x --- --- x
H323 --- --- --- --- ---

SIP --- --- --- --- ---
HG 3550
V1.1 Native SIP --- --- --- --- ---
DMC --- --- --- --- ---
HiPath
4000 HFA-Mobility --- --- --- --- ---
V4 H323 x --- --- x x
SIP --- x --- x x
HG 3500
Native SIP --- --- x --- ---
DMC x x --- x ---
H323 x --- --- x x

SIP --- x --- x x
HiPath
4000 HG 3500 Native SIP --- --- x --- ---
V5 DMC x x --- x ---
H323 x --- --- x x
SIP --- x --- x x
HiPath
4000 HG 3500 Native SIP --- --- x --- ---
V6 DMC x x --- x ---
Table 11 Networking with HiPath 4000 V6
A31003-H3160-S104-8-7620, 07/2014
gateways_07_load_concept.fm
Load Concept for Gateway Boards
Important Information
7 Load Concept for Gateway Boards
7.1 Important Information

• This chapter only describes how to update the loadware for gateway boards.
• To update the system as a whole, use the conventional HiPath 4000 Assistant
features Software Transfer and Software Activation.
• To minimize system downtime, you can upgrade the gateway boards first with
the load concept described in the following sections and afterwards upgrade
the system with the Software Transfer and Software Activation functions.
7.2 Notes on IP Gateway Loadware

• Although you can store two loadware images on the IP gateway HG3575,
only one of these is the "golden load" that is loaded after a cold start (power
off).
• Loadware ID check
A loadware ID check is performed every time the HG3575 is started and
compares the board loadware that is being downloaded with the loadware
version on the hard disk (:PDS:APSP/LTG/LGA0/PZKNCI40).
If the result of the check is negative, that is, if there is a discrepancy with the
loadware stored on the HD, then the loadware is transferred from the HD to
the NCUI via FTP and then installed/restarted.
• Installation of NCUI loadware (PZKNCUI40)

A NCUI loadware (PZKNCUI40) loaded/transfered in the background will be
installed with a warm boot.
This warm boot can be started with the following actions/events:
– Deactivate/activate with AMO USSU (DEACTIVATE-USSU/ACTIVATE-

USSU).
– Restart of the access point with EXEC-USSU:UPDATAP,<ap-

number>;. New configuration data will be loaded to the access point and
a warm boot will be initiated.
– New startup after loadware transfer (initiated through negativ LW ID

check during startup).
– after connection failure in TCP (ALVTIME).
• Golden loadware check
A31003-H3160-S104-8-7620, 07/2014
Load Concepts
In HG 3575, the latest loadware to be downloaded is called "golden loadware"

(as-delivered NCUI2+/NCUI4 boards include loadware in the flash memory).
The golden loadware check is always performed after new loadware is
downloaded/restarted (loadware upgrade/loadware ID check negative). If this
check is successful, the download pointer is rewritten as appropriate so that
the golden loadware corresponds to the new loadware.
7.3 Load Concepts

Load concept for HG 3500/HG 3575
• The loadware for HG 3500/HG 3575 is loaded via HTTPS (see Section 7.4,
“Updating Loadware with Web-Based Management” and Section 7.5,
“Updating Loadware with "LW Update Manager"”).
• Loadware can be loaded in the background during normal operation, that is

the activation of new loadware can be delayed (until off-peak hours). The new
loadware should nevertheless be activated as quickly as possible to avoid
problems.
• Optimized loading for HG 3500 gateways

As the common gateway development has combined the software of all
previous gateways (HG 3530, HG 3540, HG 3550 and HG 3570) in a single
software/loadware package, the size of the software has increased
accordingly. This has increased the loading time to approximately 15 minutes.
The load concept for STMI loadware was adapted in response to this change.
There are two CGW-STMI2 boards and two CGW-STMI4 boards. These
boards all have a different HW ID but have the same loadware file.The
optimized methodology for CGW-STMI boards means that the loadware file
is only downloaded once for these boards, even if they have different HW IDs.
This results in the following implementation scenarios:
• Configuration featuring both STMI4 types and an STMI2 type =>

loadware file is only transferred once and then distributed to all
corresponding boards.
• Configuration featuring both STMI2 types present => loadware file must
be transferred twice because the STMI2 firmware can no longer be
modified.
STMI4 boards must have at least the firmware STMI4_FW_070725 in order
to use the optimized load concept for the different CGW-STMI boards.
A31003-H3160-S104-8-7620, 07/2014
Updating Loadware with Web-Based Management
7.4 Updating Loadware with Web-Based Management
IMPORTANT: Disadvantage
You can only upgrade one IP gateway board at a time.
• To use this option, log on to HiPath 4000 Assistant and select Expert mode
> Web-Based Management for HG35xx.
• Now select the required board and click the link ???[connect]. WBM for HG
35xx now opens.
• Now select Maintenance > Software Image > Gateway Software > Load to
Gateway and right-click with the mouse.
• Select Load via HTTP.
• In the field Remote File Name (PC File System) you must enter the software
(loadware) saved previously on your PC. This is performed using the Browse
button.
A31003-H3160-S104-8-7620, 07/2014
Updating Loadware with "LW Update Manager"
• Now select the Load button to start loading. Loading can take up to five
minutes. The loadware is saved in the flash memory of the board.
IMPORTANT: The LAN must be connected but the IP gateway must not be
rebooted during the load operation (AMO USSU, AMO BSSU).
• Activate (decompress and install) the loadware.

Activation (loadware decompression and installation) now takes less than five
minutes.
You can activate the software (loadware) immediately with Activate Now or
use the Schedule Activation button to implement time-controlled activation
on a particular day.
7.5 Updating Loadware with "LW Update Manager"
IMPORTANT: Advantage
You can upgrade multiple IP gateway boards at once.
A31003-H3160-S104-8-7620, 07/2014
General Comments on Loading
Key features of "LW Update Manager"

• The "LW Update Manager" function lets you upgrade individual boards or all
boards supported.
• The LW Update is made up of two parts: Loadware Transfer and Loadware

Activation.
• Loadware can be updated immediately or after a delay, that is time-controlled

with the scheduler.
Activating "LW Update Manager"

To activate this feature, log on to HiPath 4000 Assistant and select Expert mode
> LW Update Manager.
For more information, refer to the online help for the "LW Update Manager" or
"HiPath 4000 Assistant V6, Loadware Update Manager, Administrator
Documentation" on the intranet (http://apps.g-dms.com:8081/techdoc/en/
P31003H3460M1450176A9/index.htm).
7.6 General Comments on Loading

Download speed
It takes approximately 8.5 minutes to load a CGW-STMI board (excluding
miscellaneous restore times). More time is needed in the case of an access point
with a slow IP connection (see also "Flow control (TCP)").
Flow control (TCP)

The system performs flow control. If the necessary bandwidth (quality of service)
is not available, the process slows down, that is, the speed is dictated by the
slowest access point when loading all access points simultaneously.
A31003-H3160-S104-8-7620, 07/2014
General Comments on Loading
A31003-H3160-S104-8-7620, 07/2014
gateways_08_local_flash.fm
Save Configuration Data in Local Flash ((local Backup & Restore)
Overview
8 Save Configuration Data in Local Flash ((local Backup &

Restore)
8.1 Overview
There are some customer scenarios, where the gateway boards and HiPath 4000
Assistant are in separated IP-networks (no routing between these two networks)
and therefore backup and restore functionality via HiPath 4000 Assistant is not
possible. In these cases the WBM configuration data/certificates can be saved in
local flash of the board. Then backup and restore is still possible when
connectivity to HiPath 4000 Assistant backup server is missing or the backup
server cannot be reached .
8.2 Feature Description

When "Save configuration data in local flash" is activated, a backup file is created
on the local flash at the set time of the day (default 03:00).
When "Save configuration data in local flash" is activated, a backup file is created
on the local flash whenever data is saved in the WBM. This means that virtually
no data is lost any more when loadware is updated via HDLC.
This backup file is only used in the event of a loadware upgrade which is
performed per HDLC (with an STMI) or FTP (with an NCUI). If such as upgrade
is initialized, the restore is executed using the existing backup file when the new
loadware version is started (still in startup - before the gateway status "system
ready"). Then a check is made whether the HiPath 4000 Assistant "Backup and
Restore" is reachable or whether a more up-to-date backup is available. This is
the case if between 3:00 and the current time a manual or an automatic backup
of the board was created. If there is a more up-to-date backup available on the
HiPath 4000 Assistant "Backup and Restore" and the backup server can be
reached, a second restore is carried out.
If the loadware upgrade is done via the loadware manager of the assistant, then
the backup file in the local flash (03:00) is not used. In this case a current backup
is created in the local flash before the new software is activated with the old load.
Then the new loadware version is loaded and started. During startup the backup
created shortly before is imported. This ensures that this upgrade with the local
backup/restore always contains the latest configuration data. The HiPath 4000
Assistant "Backup and Restore" must still be contacted to check the backup file.
This is important in the case of HFA standby: Here there is a backup on the
HiPath 4000 Assistant backup server with the same IP address but old MAC
address which then must be imported.
A31003-H3160-S104-8-7620, 07/2014
Startup Scenarios
Notes on rebooting
• If the backup is created from the HiPath 4000 Assistant "Backup and Restore"
before the "system ready" status of the board, then there is no additional
reboot. If the backup is created after the "system ready" status because the
HiPath 4000 Assistant backup server is not reachable immediately, then the
board is automatically rebooted in the case of SPE (because of certificates
and MEK).
• The local backup is restored during the startup phase (before the board is
operational) and therefore an additional automatic gateway reboot is only
necessary in exceptional cases (e.g. SPE certificates available).
• If additionally a HiPath 4000 Assistant "Backup and Restore" server is confi-

gured/present, the currentness of the backup determines applying board
data, i.e. restore from the local backup or the HiPath 4000 Assistant "Backup
and Restore" backup.
If the HiPath 4000 Assistant "Backup and Restore" backup is more up-to-
date, this can possibly lead to an additional reboot.
8.3 Startup Scenarios
Normal restart
Check if the backup server is configured and reachable.
• Backup server is configured, reachable and contains a newer version of

configuration data as on the local flash of the board:
-> Configuration data will be laoded from the backup server. This is normally
the case after upgrade over HDLC or exchanging the physical board.
• Backup server is configured and reachable, but no backup with

configuration data is stored/found:
The gateway starts up using its default configuration data. No retry to reach
the backup server is executed.
• Backup server is configured but not reachable:

A retry to reach the backup server is executed.
• Backup server is not configured.

The gateway starts up using its default configuration data. No retry to reach
the backup server is executed.
A31003-H3160-S104-8-7620, 07/2014
Startup Scenarios
Loadware Update via HDLC
Same procedures as normal restart. When upgrading via HDLC the board can’t
have stored the current configuration data to the local flash (TFFS).
Configuration data is essentially no longer lost when a loadware update is

performed via HDLC as a backup file is created on the local flash whenever data
is saved in the WBM.
Loadware Update via HiPath 4000 Assistant / WBM
After activating the new loadware the gateway will be automatically rebooted. The
new gateway loadware is loaded. The new loadwrae image loads the previously
stored configuration data. The data on the backup server can not be more up-to-
date, therefore it is not taken into consideration.
For more information on the loadware update via HiPath 4000 Assistant / WBM
please refer to Chapter 7, “Load Concept for Gateway Boards”.
Loadware Update via HiPath 4000 Assistant / WBM: backup server not
configured
Same as „Loadware Update via HiPath 4000 Assistant / WBM“.
Loadware Update via HiPath 4000 Assistant / WBM: backup server

configured but not reachable (via IP)

configured and reachable, but no backup with configuration data is stored/
found

configured and reachable, but on the backup server an older configuration
than the current one is found
Same as„Loadware Update via HiPath 4000 Assistant / WBM“.
A31003-H3160-S104-8-7620, 07/2014
Configuration
8.4 Configuration
The feature will be configured with the WBM of the board.
WBM > Maintenance > Actions > (double-click) Automatic Actions > Saving
Local Configuration for Upgrade
8.5 Special Use Cases

• Board replacement
The new board has already a stored backup file in the local flash (but with
another functionality than the one that will be replaced).
Because there is a backup file in the local flash it will be used for restoring the
data. But because of the board replacement the MAC address of the board
has changed. Therefore HiPath Backup & Restore is contacted to perform a
restore with the backup file of the backup server. After the restore from the
backup server the correct data is configured on the board. In this case the
backup server must be reachable otherwise the board has stored the wrong
configuration data.
After the restore the backup of the local flash should be updated with the
current configuration data.
• Default configuration (empty data base)

An empty data base can be configured as follows:
WBM > Maintenance > Configuration > (right mouse) Reset Configuration
to Factory Default ...
With choosing this option the board will be reseted automatically. During the
startup of the board the parameters configured via AMO will be loaded. The
WBM parameters will be set to default.
A31003-H3160-S104-8-7620, 07/2014
gateways_09_fpga_code_update.fm
Loadability of the FPGA on the STMI4/NCUI4 board
9 Loadability of the FPGA on the STMI4/NCUI4 board

It is possible to load the FPGA code on the gateway boards STMI4 and NCUI4.
Usually the FPGA code is supplied with a LW hotfix (or via fix release, minor
release, hotfix). There are three files:
• the SENTA file,
• COMGA file for STMI4 and
• COMGA file for NCUI4.
IMPORTANT: The update of the SENTA/COMGA firmware (FPGA code) cannot

be done from remote!
Figure 16 FPGA - Hardware components involved
Prerequisite:
The loadware for SENTA /COMGA must be saved via PCHI tool / ftp transfer
(binary) on the PC. Before the update can be executed, the loadware must be
transferred to a PC in the customer’s network and which has access to the WBM
of the board (WBM client).
Update:
The update of SENTA loadware and COMGA loadware is done via WBM. In the
section Maintenance > Firmware > Load to Gateway you have two possibilities:
• Load COMGA-Firmware via HTTP or
• Load SENTA-Firmware via HTTP.
A31003-H3160-S104-8-7620, 07/2014
IMPORTANT: The following description of the firmware update is done for

SENTA loadware.
For COMGA firmware the instructions are the same but choose Load COMGA-
Firmware via HTTP from the menu.
1. Choose Load SENTA-Firmware via HTTP from the menu.
1. Select the new file of the SENTA loadware from your local PC by pressing the
Browse button.
2. Press the Load button for staring the loadware transfer to the flash memeory
of the board.
A31003-H3160-S104-8-7620, 07/2014
3. Upload process has finished when the following screen appears.
Confirm with OK.
A31003-H3160-S104-8-7620, 07/2014
4. Activate the new SENTA firmware by pressing the Activate now button.
IMPORTANT: After completion of the activation process the gateway will be

rebooted automatically!
5. Confirm the activation process by clicking OK.
The new SENTA firmware will be updated, activated and the gateway will be
rebooted.
Trace:
The whole process can be monitored with switched on trace SWCONF, level 9
(see The phase of downloading of the SENTA firmware).
Failure:
In the case of failure, a popup window appears in the WBM with an error code
(see Traces for failure). The activation of the loadware and the reboot of the
gateway is not performed.
The phase of downloading of the SENTA firmware

(SWCONF tEmWeb 0x353c4c0 "08/25/2008 15:43:43.688177" cswconfigsvc03.cpp 175)
Creating Job! Type=0x1f001b, ID=3

Created Job 3
(SWCONF tEmWeb 0x353c4c0 "08/25/2008 15:43:43.702931" cswconfjob02.cpp 3357)

Firmware type: SENTA

First block. Retrieving image header.

offset | 0 1 2 3 4 5 6 7 8 9 a b c d e f |
--------+--------------------------------------------------+-----------------
A31003-H3160-S104-8-7620, 07/2014
00000000| B2 00 00 00 04 30 37 2F 31 30 2F 30 38 31 33 3A | .....07/10/0813:
00000010| 30 36 3A 35 34 17 45 4C 46 3E 49 33 38 36 50 5A | 06:54.ELF>I386PZ
00000020| 4B 53 45 4E 30 31 2E 4F 31 2E 30 31 32 00 00 00 | KSEN01.O1.012...
00000030| 00 00 30 00 99 78 70 7A 6B 73 65 6E 30 31 00 00 | ..0..xpzksen01..
00000040| 00 00 00 00 00 00 00 00 00 00 00 00 68 00 00 00 | ............h...
00000050| 00 00 00 00 50 D9 10 00 00 00 00 00 00 00 00 00 | ....P...........
00000060| 00 00 00 00 00 00 00 00 | ........

Transfer status for job 3 is 1% (11540/1092718)
(SWCONF tBackupTask 0x30622e8 "08/25/2008 15:43:43.774272" cswconfigsvc01.cpp 43

9)
Execute Job in Queue:
ID = 3, Action=0x1f001b



Writing block of 1104096 bytes, remaining 1 bytes

Writing block finished OK.


Got last part of the buffer

Writing remaining buffer: 0 bytes

offset | 0 1 2 3 4 5 6 7 8 9 a b c d e f |
--------+--------------------------------------------------+-----------------
00000000| 70 7A 6B 73 65 6E 30 31 17 45 4C 46 3E 49 33 38 | pzksen01.ELF>I38
00000010| 36 50 5A 4B 53 45 4E 30 31 2E 4F 31 2E 30 31 32 | 6PZKSEN01.O1.012
00000020| 00 00 00 00 00 30 00 00 00 99 78 30 37 2F 31 30 | .....0....x07/10
00000030| 2F 30 38 20 20 31 33 3A 30 36 3A 35 34 | /08 13:06:54

Writing loadware ID finished OK.


Progress Response:
Transferred File Size=1104209
Complete File Size=1092718
A31003-H3160-S104-8-7620, 07/2014
Progress Response:

Progress Response:

Progress Response:
The second phase of the process:

File info: compressed size: 1104096, uncompressed size: 12491489

Uncompression successful
(SWCONF tEmWeb 0x353c4c0 "08/25/2008 15:44:23.147303" util.c 4765)

... writing SENTA FPGA code to SENTA flash

writting SENTA FPGA code to SENTA flash is still running










A31003-H3160-S104-8-7620, 07/2014
















programming SENTA flash finished
.....
(SWCONF tEmWeb 0x440e168 "08/29/2008 10:43:37.050407" util.c 3928)

active SENTA version on revision 1: 12
(SWCONF tEmWeb 0x440e168 "08/29/2008 10:43:37.056302" cswconfjob07.cpp 539)

!!! Initializing reboot !!!
(EVTLOG tEvtLogTask 0x36de430 "08/29/2008 10:43:37.058440" cevtlogsvc01.cpp 942)
A31003-H3160-S104-8-7620, 07/2014
EventLogEntry from SYSTEM (tEmWeb "08/29/2008 10:43:37.056510" cswconfjob07.cpp

544):
EventType: Information
EventCode: MSG_ADMIN_REBOOT
EventText: Reboot initiated by Admin (Firmware Activation)
Executing Shutdown and Reboot for EvtCode 100 (MSG_ADMIN_REBOOT)
Exiting Security Task*** Shutdown.
Traces for failure

(SWCONF tFPGAWrite 0x4e39e88 "08/28/2008 15:06:53.579613" util.c
3666)
call of xsvfExecute returned error:2
A31003-H3160-S104-8-7620, 07/2014
gateways_10_standby.fm
Standby Board HG 3500
Feature Description
10 Standby Board HG 3500

The feature “Standby Board HG 3500” is supported for all common gateway
boards. Regardless of the boards configuration as single feature mode or as
multiple feature support (MFS).
IMPORTANT: Restriction
In the case of MFS, only the entire board can be transferred to the standby board!

This feature is designed to increase the availability of IP terminals, IP trunking
lines, etc, in the event of board failure or LAN cable defects.
Board pool No.1
Direct Link
HG 3500-2 optiPoint IP
IP Subscriber: 2160
IP
Gateway: HG 3500-1
HG 3500-1
IP optiPoint IP
IP
LAN
HG 3500-3
IP Subscriber: 2150
Gateway: HG 3500-2
HiPath 4000
Figure 17 HFA infrastructure
This is achieved through the introduction of a standby board. In the event of a

board or LAN cable defect, standby boards can inherit the IP stations or IP
trunking lines, etc. assigned to an active board. If appropriately configured, this
action can be performed automatically, that is, without manual intervention or use
of AMO commands. This is illustrated in the following example which depicts a
common gateway with HFA stations.
In the example in Figure 17 HFA infrastructure, the standby board is the HG 3500-
3. If, for example, an HG 3500-1 fails, the IP Phone 2160 will be reconfigured to
HG 3500-3 and goes into operation with the new board.
Provided this feature was preconfigured (see below), automatic switchover takes
place in the following events:
• When the board is removed without prior deactivation
A31003-H3160-S104-8-7620, 07/2014
Feature Description
• Faults on the LAN connection cable. Please note that LAN faults that are
located “behind“ routers, hubs or IP switches do not trigger a switchover, and
nor do faults on IP terminal devices. The switchover mechanism is only
triggered by a signaled Layer 1 fault, that is, a general cable defect.
• Faults that are detected by the security system and that lead to the DC status
“DEF“ (on board level), for example, “Message not transmittable. Exception:
a statistic overflow does not lead to a switchover.
The automatic switchover mechanism is not triggered if either the board or

hierarchically superior elements (LTU, LTG) are disabled.
The IP terminals go out of operation during switchover and are automatically put
back into operation following a successful switchover. The duration of the
switchover process is determined by the board data loading time and by timers
on the board and in the terminal device. It normally takes between one and two
minutes.
Please note that, following the switchover operation, the board sends a
“gratuitous ARP” (Address Resolution Protocol) request to the LAN on startup so
that the MAC address (which has changed with the board) associated with the IP
address is updated in the LAN components immediately rather than waiting until
the aging timer expires. On the LAN side, take care that the ARP request does
not get blocked by any routers that may be involved.
The automatic switchover is signaled at the service terminal. SYSDEP-NMC also

receives a message confirming switchover. Designed specially for this purpos is
the NMC alarm 36 (PER-BOARD SWITCHOVER). The message at the service
terminal is as follows:
F5880 M4 N0542 NO ACT BPA BOARD RECONFIGURATION
06-11-09 10:13:30
ALARM CLASS:CENTRAL:036
P101 :LTG1 :LTU3 :055: 0-239:90 Q2316-X10 STMI2/1
BST:01 PLS:-06
FORMAT:43
REASON:00H BOARD RECONFIGURATION OK
SOURCE BOARD : P117:LTG1 :LTU17:097:
DESTINATION BOARD : P101:LTG1 :LTU3 :055:
If the service personnel has replaced the defective board on which the IP stations
were originally configured with an intact board, then the IP stations can be
configured back in the course of manual startup. The board that took over
operation after the defect was discovered resumes its role as standby board and
is ready for switchover in the event of future defects.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Apart from automatically switching IP stations to a standby board when a defect

occurs, this feature also offers manual switchover options that can be
implemented with the AMO BSSU. This lets the IP stations maintain their group
relationships, which means there is no need for station reconfiguration with the
AMO SBCSU, AMO AUN, etc.
The feature must be preconfigured before it can be put into operation. This
involves the following steps (for AMO details see Section 10.4, “Generation”):
1. Configure the common gateway board: Both the normal boards (on which the
IP stations are configured) and the standby boards are configured as usual
with the AMO BFDAT and AMO BCSU. No distinction is made at this stage
between the two functions.
2. Configure common gateway board data: The common gateway boards are
normally parameterized with the AMO CGWB. The parameters set here
determine whether the board will be used as a normal board with IP stations
or as a standby board. The normal boards must be assigned an IP address
(as in previous configurations), whereas the standby boards are programmed
with no IP address or other parameters.
3. All common gateway boards that want to use the feature must be grouped
together in a board pool with the AMO BPOOL. A board pool is administered
by means of a pool number and must contain both the normal boards and the
standby boards. Only when this is complete can a normal board switch over
to a standby board in the event of a defect. 
Please note that following a defect, a pool-based board can only be
automatically switched to a standby board in the same pool. In the case of
AMO-activated manual switchover, on the other hand, the board and standby
can be located in separate pools; both boards must, however, belong to a
pool (any pool) for this function to work.
4. As usual, the IP stations are configured on the normal boards and put into
operation with the AMO SBCSU. Stations cannot be configured on a standby
board.
Besides the functionalities described above, the feature also offers the following
functions:
• The following attributes can be set on a pool-specific basis:
– SINGLE / MULTI
This setting specifies whether automatic switchover should be performed
once (SINGLE) or several times, such as when further defects occur.
– INFO
The purpose of this is to provide clarity when operating multiple pools. It
may be useful to assign names to pools.
• Trace pool history
A31003-H3160-S104-8-7620, 07/2014
Feature Description
A History field is provided for every board in the pool. The following
information can be entered here and read out with the AMO BPOOL:
– Board (LTU, slot) from which the stations currently configured were
switched
– Board (LTU, slot) to which the stations previously configured were

switched
– Date and time at which the IP stations were switched to or from the board
– Counter indicating how often the stations currently configured were

switched
This information is available separately for automatic switchover (following a
defect) and for manual switchover. The AMO BPOOL can be used to reset
the history data (but only for all data simultaneously).
The history only contains information on the last switchover performed. Only
the counters provide information on all switchover stages.
IMPORTANT: For automatic IP station switchover to work, the boards must be

in operation (DC status “Ready“) at the time of the defect. The feature is not
implemented if a defect is discovered when starting up the board or the system;
in this case, an automatic restart is performed. This is necessary for system
stability reasons.
Exception: A detached LAN cable results in a successful start; the later detection
of the LAN cable failure activates the automatic switchover as long as a standby
board is available.
SINGLE
If SINGLE automatic switchover is configured, further defects do not trigger a

switchover to a standby board, even if there are standby boards available in the
pool. This setting allows stations to be switched back manually after the defective
board has been replaced, without having to specify their current location.
MULTI
If MULTI automatic switchover is configured, defects continue to trigger

switchovers until there are no more standby boards available in the pool. When
switching back manually, you must specify the boards from which and to which
the stations should be switched. In other words, you must know or find out the
source board and the target board.
A31003-H3160-S104-8-7620, 07/2014
User Interface
10.2 User Interface

No particular consequences for telephone users. During the switchover phase,
the telephone is “dead“; its display is cleared and reappears as soon as the
telephone becomes operational on the new board. Before this point, additional
temporary messages such as PBX NOT FOUND may appear on the display.
10.3 Service Information

IP station switchover can be likened to a reconfiguration. This means that
reconfiguration does not take effect after a system reload unless the static data
was written to the hard disk with EXEC-UPDAT:BP,ALL;
IMPORTANT: If a system reload is performed after the IP stations have been

switched over to a standby board and before backing up the database to the hard
disk with the AMO UPDAT, the IP stations remain configured on their old board
after the reload. If this old board is still defective or has been removed,
switchover is not performed because the condition that the board must be in
operation at the time of the defect is not satisfied (exception: a defective LAN
cable cannot be detected until the board is in operation, and in this case a
switchover is performed).
The new type branch to SMODE was introduced in the AMO CGWB for this
feature.
There are two versions of standby mode:
1. STBYRDY: Means “Standby Ready” and describes a standby board that

is ready to inherit stations. Normally, the DC status of this board is
“Ready” because the board evaluates the standby mode and sends a
positive load acknowledgement to the system in response to STBYRDY”.
The LAN status can be “Ready” or “DEF”. If a board is to serve as a
standby board, both its DC status and the LAN status must be “Ready”.
2. STBYDEF: Means “Standby Defect” and describes a board from which
the IP stations were switched on account of a defect. This board cannot
serve as a standby board because its DC target status is “DEF”. Normally,
the DC status of this board is “DEF” or “NL” if the board is inserted or
“NPR” if the board is removed. The loadware that evaluates the standby
mode sends a negative acknowledgement to the system in response to
STBYDEF (DEF ON REQUEST).
Boards that are in standby mode do not have a separate IP address or any board
data. The standby board only receives all the board data (including the IP
address) when they are transferred to it from the source (defective) board on
switching over the IP terminals. Following switchover, the source board is
A31003-H3160-S104-8-7620, 07/2014
Service Information
transformed into a standby board (for example, STBYDEF), which means it no

longer has an IP address. Although the standby board is physically connected to
the LAN, meaning that Layer 1 remains in operation, the higher layers are
deactivated. LAN-based access, for example over FTP, Telnet or SNMP, is
therefore impossible with a standby board.
IMPORTANT: Please note that the Ethernet bit rate configured in the board data
is also transferred from the source board to the standby board. The LAN segment
to which the standby board is connected must therefore have the same bit rate
as the source board’s LAN segment.
The feature is restricted to a single system: cross-system application is not

supported.
It is possible, however, to organize the IPDA architecture in such a way that the
common gateway boards and standby boards are randomly distributed over the
HHS (HiPath Host System) or in the AP (Access Point). In this case, all boards
must be connected to the LAN.
IMPORTANT: It is important to note that LAN-based availability is guaranteed so

that not only the active board but also the standby board can reach the IP stations
and vice versa. 
In addition, be sure to trigger the change in mapping of IP address to MAC
address with the previously mentioned ARP requests in the LAN components.
This “gratuitous ARP“ request may not be blocked (e.g. in the router configu-
ration).
We recommend testing the automatic switchover mechanism in the course of

initial start to ensure it is in working condition and ready to tackle real defects.
As board data is also transferred in the course of manual and automatic station
switchover, restrictions apply if the switchover takes place between fully
configured (for example, Q2316-X10) and partially configured boards (for
example, Q2316-X). Please note the following in this case:
• No restrictions apply if the pool only contains boards of the same type, that is,
boards that have the same DSP resources and thus the same number of
active connections.
• If you are switching from a partially configured board to a fully configured

board, then, following switchover, the number of active connections is
restricted to the number supported by the partially configured system. You
must increase the UDP port range to be able to use all of the fully configured
board’s resources. Please note that any existing firewalls must be adapted in
line with the new UDP range.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• If you are switching from a fully configured board to a partially configured

board, then, following switchover, only a reduced number of active
connections is possible on the new board, that is, the number supported by
the partially configured board. This can lead to frequent blockages in
configurations with many stations and high switching loads.
If manually switching the IP stations from a source board to a target board

(command: RESTART-BSSU:...,CGWSW=SWITCH,...;), then please note the
following points:
• The target board must be in STBYRDY standby mode and its DC status must
be “Ready“ (for example, not locked by means of an AMO), and its LAN cable
must be connected.
• The source board must not be in standby mode, that is, SMODE=NORMAL
must be set. Otherwise, the board can display any DC status - it can even be
locked by means of an AMO. If this is the case, the manual lock is transferred
to the target board. If the DC status or the status of the source board’s LAN
connection is “DEF” prior to switchover, SMODE=STBYDEF is entered after
switchover. In all other cases, SMODE=STBYRDY is set, meaning that this
board can once again operate as a standby board.
IMPORTANT: To the extent that it plays a role in the switchover, the LAN
connection status (Layer 1) can be queried with the AMO BPOOL. And of
course you can use the AMO SDSU as before.
SMODE
SMODE describes the common gateway board’s standby mode. Standby mode
determines whether a board is configured as a normal board with IP stations, IP
address, etc., or whether it is a standby board.
A31003-H3160-S104-8-7620, 07/2014
Generation
10.4 Generation
Board pool No.1

Direct Link
HG 3500-2
optiPoint IP
1-17-2 (Normal)
IP
1-3-49 (Normal) IP Subsriber: 2160
Gateway: HG 3500-1
HG 3500-1
IP optiPoint IP
LAN
IP
HG 3500-3
IP Subsrciber: 2150
Gateway: HG 3500-2
HiPath 4000
1-3-109 (Standby)
In the interest of clarity and to keep things simple, we will not discuss the general
configuration of DPLN, LTU, etc. here. However, a list of all common gateway
specific commands is provided:
Configure the DIMSU memory for the common gateway boards:

ADD-DIMSU:TYPE=SYSTEM,CGW=4;
Configure the common gateway boards:
FCTBLK=1 : HG 3500-1
ADD-BFDAT:FCTBLK=1,FUNCTION=HG3530,BRDBCHL=BCHL60;
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3530,LINECNT=60,BCHLCNT=30
;
CHANGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES;
FCTBLK=2 : HG 3500-2
CHANGE-
0;
FCTBLK=3 : HG 3500-3 (Reserve-Baugruppe)
ADD-BFDAT:FCTBLK=3,FUNCTION=STANDBY,BRDBCHL=BCHL60&BCHL120;
Assigning a function block to a board:
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=3,SLOT=49,PARTNO=Q2316-
X,FCTID=1,FCTBLK=1; /*HG 3500-1
A31003-H3160-S104-8-7620, 07/2014
Generation
X10,FCTID=1,FCTBLK=2; /*HG 3500-2
ADD-BCSU:MTYPE=IPGW,LTU=3,SLOT=109,PARTNO=Q2316-
X,FCTID=1,FCTBLK=3; /*Standby board HG 3500-3
Configuration of common and global feature board data of the common gateway
board. In this example 2 normal and one standby board will be configured:
ADD-
CGWB:LTU=3,SLOT=49,SMODE=NORMAL,IPADR=192.16.16.12,NETMASK=255.2
55.255.0; /*HG 3500-1
ADD-
55.255.0; /*HG 3500-2
ADD-CGWB:LTU=3,SLOT=109,SMODE=STBYRDY; /* Standby board HG 3500-
3
Load the board data to the boards:

RESTART-BSSU:ADDRTYPE=PEN,LTU=17,SLOT=2,WTIME=10;
Configure a board pool with all boards including standby board(s):
ADD-
BPOOL:MTYPE=CGW,LTU=17,SLOT=2,POOLNO=1,HOPAUT=SINGLE,INFO=“TEST1
“;
ADD-BPOOL:MTYPE=CGW,LTU=3,SLOT=109,POOLNO=1; /* Standby Board */
ADD-BPOOL:MTYPE=CGW,LTU=3,SLOT=49,POOLNO=1;
Configure the IP stations:
ADD-SBCSU:STNO=2150,OPT=OPTI,CONN=IP2,PEN=1-17-2-29,
DVCFIG=OPTIIP,COS1=5,COS2=6,LCOSV1=11,LCOSV2=12,LCOSD1=21,LCOSD2
=22;
ADD-SBCSU:STNO=2160,OPT=OPTI,CONN=IP2,PEN=1-3-49-0,
DVCFIG=OPTIIP,COS1=5,COS2=6,LCOSV1=11,
LCOSV2=12,LCOSD1=21,LCOSD2=22;
Reset FUNSU bit to shorten the Reload time of the STMI2 board
CHANGE-FUNSU:PIT=FLASH,PARTNO=”Q2316-X”,FCTID=3,ACTION=RESET;
1. Automatic switchover: This is not controlled by AMO commands but rather is
triggered when an active board goes out of service.
Example prior to automatic switchover:
DIS-BPOOL;
H500: AMO BPOOL STARTED
+------------------------------------------------------------------------------+
| POOLNO = 1 MTYPE = CGW HOPAUT = SINGLE |
| INFO = TEST1 |
+------------------------------------------------------------------------------+
| LTU = 3 SLOT = 49 HOP-AUT-CNT = 0 HOP-MAN-CNT = 0 |
A31003-H3160-S104-8-7620, 07/2014
Generation
| DC-STATUS = READY LAN_VERB = READY SMODE = NORMAL |

+------------------------------------------------------------------------------+
| DC-STATUS = READY LAN_VERB = READY SMODE = STBYRDY |
+------------------------------------------------------------------------------+
+------------------------------------------------------------------------------+
If board 1-3-49 now becomes defective, all board data and all IP stations are
switched to standby board 1-3-109. This provides the following AMO BPOOL
output after the switchover:
DIS-BPOOL;
H500: AMO BPOOL STARTED
+------------------------------------------------------------------------------+
| POOLNO = 1 MTYPE = CGW HOPAUT = SINGLE |
| INFO = TEST1 |
+------------------------------------------------------------------------------+
| DC-STATUS = NPR LAN_VERB = SMODE = STBYDEF |
| SWITCHED AUTTO BRD LTU = 3 SLOT = 109 DATE/TIME : 2003-09-25 18:07 |
+------------------------------------------------------------------------------+
| SWITCHED AUTFR BRD LTU = 3 SLOT = 49 DATE/TIME : 2003-09-25 18:07 |
+------------------------------------------------------------------------------+
+------------------------------------------------------------------------------+
Explanation of important abbreviations in the output:

HOPAUT: Automatic switchover between the boards in this pool is permitted
once (SINGLE) or several times (MULTI).
SMODE: Standby mode (see Section 10.3, “Service Information”)
HOP-AUT-CNT: Number of automatic switchovers
HOP-MAN-CNT: Number of manual switchovers
DC-STATUS: The board’s DC status (see also AMO SDSU)
LAN_VERB: LAN connection status; READY generally means “LAN cable
connected”, DEF means “LAN cable disconnected or defective”. If the field is
empty, the LAN connection has a DC status which does not get interpreted by
the AMO BPOOL. In this case, the LAN status has no effect on switchover. If
this is of interest, you can use the AMO SDSU.
The following history data is only displayed after a switchover:
SWITCHED AUTFR BRD: The IP stations were automatically switched away
from this board (for example, on account of a defect) (see also DATE/TIME)
A31003-H3160-S104-8-7620, 07/2014
Generation
SWITCHED AUTTO BRD: The IP stations were automatically switched back

to this board (for example, on account of a defect in another board) (see also
DATE/TIME)
SWITCHED MANFR BRD: The IP stations were manually switched away
from this board (with the AMO BSSU) (see also DATE/TIME)
SWITCHED MANTO BRD: The IP stations were manually switched back to
this board (with the AMO BSSU) (see also DATE/TIME)
The history data can be reset with the following AMO command:
CHANGE-BPOOL:MTYPE=CGW,TYPE=HISTRES,LTU=3,SLOT=109;
All functions assigned to board 1-3-49 are now transferred to board 1-3-109,
including the board’s IP address and all IP stations. The supplementary
information shows the history of the last switching operation. This example
shows that on 25.9.2003, a switchover occurred from 1-3-49 to 1-3-103
because board 1-3-49 was removed (DC status NPR).
The counters HOP-AUT-CNT and HOP-MAN-CNT are set for boards with
SMODE=NORMAL. All history data is deleted for standby boards.
2. Manual switchover with the AMO BSSU:
a) The stations switched away from 1-3-49 on account of a board defect

should be switched back into service following the repair of 1-3-49:
RESTART-BSSU:ADDRTYPE=PEN,LTU=3,SLOT=49,CGWSW=IPSTNBCK;
or
ACTIVATE-BSSU:LTU=3,SLOT=49,CGWSW=IPSTNBCK;
b) All IP stations assigned to board 1-3-49 should be switched to standby
board 1-3-109:
RESTART-BSSU:ADDRTYPE=PEN,LTU=3,SLOT=49,CGWSW=SWITCH,
LTU2=3,SLOT2=109;
Please note that any AMO lock set will be transferred to the target board
(see also Section 10.3, “Service Information”)
c) A board that is in STBYDEF standby mode because of a defect, for

example, and because the IP stations were switched away should
resume its standby board role. This generally occurs after it has been
repaired or the board has been replaced. The following command can be
used for this:
RESTART-BSSU:ADDRTYPE=PEN,LTU=3,SLOT=49,CGWSW=STBYRDY;
3. Shorten the Reload time of the common gateway board
CHANGE-FUNSU:PIT=FLASH,PARTNO=”Q2316-X”,FCTID=1,ACTION=RESET;
A31003-H3160-S104-8-7620, 07/2014
Service steps after the automatic switch over
10.5 Service steps after the automatic switch over

Two steps can be different after a switch over in case of error:
1. The subscribers which are switched over should get their original pens.
In this case the board pool has to be defined as HOPAUT=SINGLE !
– Change the defective board resp. reconnect the LAN connection.
– Switch back the subscribers with the AMO command

RESTART-BSSU:ADDRTYPE=PEN,LTU=xx,SLOT=xx,CGWSW=CGWSWBCK;
(xx -> Pen of the board with status STDBYDEF)
– Reset the history data of the Board Pool:

CHANGE-BPOOL:MTYPE=CGW,TYPE=HISTRES,LTU=y,SLOT=zz;
2. The subscribers which are switched over should remain on the new pens.
In this case the board pool has to be defined as HOPAUT=MULTI !
– Change the defective board resp. reconnect the LAN connection.
– Switch the STDBYDEF board to STDBYRDY with the AMO command

RESTART-BSSU:ADDRTYPE=PEN,LTU=xx,SLOT=xx,CGWSW=STBYRDY;
10.6 Relevant AMOs
AMO Parameter Sprache/ Beschreibung/ Description

Language
BCSU ALARMNR d Alarm Nummer
ALARMNO e Alarm number
BKAN3530 d Anzahl der B-Kanaele fuer die HG3530
Funktion
BCHL3530 e Number of b-channels for HG3530 function
FCTID d Function Id (muss immer 1 sein)
FCTID e Function id (must always be set to 1)
FCTBLK d Funktionsblock-Index (einen beliebigen freien
Funktionsblock zwischen 1-20 wählen)
FCTBLK e Function block index (choose a free function
block between 1-20)
LWVAR d Index auf Loadware Block der T1 Baugruppe
LWVAR e Index to loadware block for the t1 board
SACHNR d Baugruppensachnummer (2. und 3. Block)
Q2316-X, Q2316-X10, Q2324-X500, Q2324-
X510
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs

Language
PARTNO e Part numver (2nd and 3rd bloc)
Q2316-X, Q2316-X10, Q2324-X500, Q2324-
X510
TYP=IPGW d IP Gateway (Common Gateway Baugruppe)
MTYPE=IPGW e IP gateway (common gateway board)
BFDAT ANZBKAN d Anzahl der funktionsbezogenen B-Kanäle.
BCHLCNT e Defines the number of b-channels related to the
selected function.
ANZSATZ d Anzahl der funktionsbezogenen Saetze.
Mögliche Werte: 1-240
LINECNT e Defines the number of lines related to the
selected function.
BGBKAN d Block fuer Baugruppe mit 60 und/oder 120 B-
Kanaelen
BRDBCHL e Dedicates the block for boards with 60 and/or
120 b-channels
CONFIG=WEIT d Weitere Block-Konfiguration ermöglichen
ER
CONFIG=CON e ontinue block configuration
T
CONFIG=OK d Block-Konfiguration abschließen
CONFIG=OK e Finish block configuration
FCTBLK d Dieser Index beschreibt den Funktionsblock
welcher auf dem Common Gateway
konfiguriert werden soll. Anhand des
Funktionsblocks wird die Konfiguration der
benötigten pyhsikalischen Lines (Sätze der
Baugruppe) festgelegt.
FCTBLK e This index describes the function block which
should be configured on the common gateway
board. With that index the amount of needed
physical lines (board circuits) is calculated.
FUNCTION d Dieser Parameter legt das
Konfigurationsprofile des Common Gateways
fest. Dabei muss die eventuell benötigte HG
3570 Funktion als erste angeführt werden. Falls
ein bestimmter Line-Bereich für die Funktionen
HG 3530 oder HG 3550 vorreserviert werden
soll, muss die entsprechende Funktion am
Ende stehen und mit dem Wert HG35xxR
abgeschlossen sein. Die Funktion STANDBY
kann nur als Einzel-Funktion konfiguriert
werden.
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs

Language
FUNCTION e This parameter defines the configuration profile
of the CGW board. If HG3570 functionality is
used, it must be configured at first position. If a
prereservation of a certain line range of
functions HG3530, HG3540 or HG3550 is
desired, this function must be at the end of the
profile just suffixed by the according HG35xxR
value. The function STANDBY can only be
configured as single function.
BPOOL ART d Art der Pool-Daten:
ALLE = Alle Pools löschen
ATTR = Pool-Attribut ändern
BAUGR = Baugruppe aus Pool löschen
HISTRES = Historie der Baugruppe rücksetzen
POOL = Einen bestimmten Pool löschen
TYPE e Type of pool data:
ALL = Delete all Pools
ATTR = Change pool attribute
BOARD = Delete board from pool
HISTRES = Reset history for a board
POOL = Delete a specific pool
EBT d Einbauteilung
SLOT e Slot
HOPAUT d Pool-Attribut für die Hop-Kontrolle beim
automatischen Umschalten:
SINGLE = nur automatisches einmaliges
Umschalten erlaubt
MULTI = mehrfaches automatisches
Umschalten erlaubt
HOPAUT e Pool attribute for the hop control for automatic
switchover:
SINGLE = Automatic switchover is allowed only
once
MULTI = Automatic switchover is allowed
several times
INFO d Pool-Attribut: Informationstext
INFO e Pool attribute: Information text
LTU d Line Trunk Unit
LTU e Line Trunk Unit
MTYP d Modultyp, derzeit nur CGW möglich
MTYPE e Module Type, currently onl CGW possible
POOLNR d Nummer des Baugruppen-Rekonfigurations-
Pools
POOLNO e Number of the Board Reconfiguration Pool
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs

Language
BSSU CGWSA d CGW Schaltauftrag:
CGWSWBCK: Rückschalten aller automatisch
weggeschalteter IP Teilnehmer auf die Original-
CGW-Baugruppe
KEIN: Kein CGW bezogener Schaltauftrag
STBYRDY: Verwendung als CGW Standby-
Baugruppe (Reserve-Baugruppe)
UMSCH: Umschalten der IP Teilnehmer der
CGW-Baugruppe auf eine andere Baugruppe
CGWSW e CGW switching activity:
CGWSWBCK: Switch IP stations back to
original CGW board
NONE: No CGW specific activities
STBYRDY: Act as CGW standby board
SWITCH: Switchover IP stations of CGW board
to another board
LTG2 d Line Trunk Group der Zielbaugruppe bei
CGWSA=UMSCH
LTG2 e Line Trunk Group of the destination board of
CGWSW=SWITCH
LTU2 d Line Trunk Unit der Zielbaugruppe bei
CGWSA=UMSCH
LTU2 e Line Trunk Unit of the destination board of
CGWSW=SWITCH
EBT2 d Einbauteilung der Zielbaugruppe bei
CGWSA=UMSCH
SLOT2 e Slot of the destination board of
CGWSW=SWITCH
CGWB SMODE d Standby Mode oder Normal Mode
Normal: Eine Baugruppe im Normal Mode hat
gültige Baugruppendaten und normalerweise
auch OPTIIPs konfiguriert.
STDBYRDY: Eine Baugruppe im Standby
Ready Mode hat keine gültigen
Baugruppendaten, auf diese Baugruppe
können OPTIIPs umgeschaltet werden, falls
eine andere Baugruppe aus demselben
Baugruppen-Pool (AMO BPOOL) defekt
wurde.
STDBYDEF: Eine Baugruppe im Standby
Defekt Mode hat ebenfalls keine gültigen
Baugruppendaten, diese Baugruppe hat
aufgrund eines Defekts seine OPTIIPs und
seine Baugruppendaten abgegeben.
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs

Language
SMODE e Standby Mode or Normal Mode
NORMAL: A board in Normal Mode has valid
board data and normally also OPTIIPs
assigned to it.
STDBYRDY: A board in Standby Ready Mode
has no valid board data, to this board OPTIIPs
can be switched over if another board of the
same board reconfiguration pool (AMO
BPOOL) becomes defective.
STDBYDEF: A board in Standby Defect Mode
has also no valid board data, this board has lost
its OPTIIPs and its board data to another board
because it's gone defective.
IPADR d IP Adresse der Common Gateway Baugruppe
(Source Adresse)
IPADR e Source IP address of common gateway board
NETMASK d IP-Netzmaske des LAN-Segmentes. Die IP-
Netzmaske bestimmt die Grenze zwischen
Netz- und Host-Teil in der IP-Adresse. Alle IP-
Adressen am LAN-Segment müssen bezüglich
des Netzanteils der IP-Adresse gleich und
bezüglich des Host-Teils unterschiedlich sein
(auch der Default Router muss dieser
Bedingung entsprechen).
NETMASK e IP net mask of LAN segment The IP net mask
determines the network and the host partition of
an IP address. All IP addresses of a LAN
segment must contain the identical network
addresss part but different host address parts
(also the Default Router must fulfill this
requirement)
FUNSU AKTION d Ladeart der Baugruppe: Damit der LW Code
nicht bei jedem Baugruppen-Reset geladen
wird, sollte RESET eingestellt sein.
ACTION e Action set or reset loadware on board:
In order to avoid loading of the LW code, it is
recommended to set this parameter to RESET.
A31003-H3160-S104-8-7620, 07/2014
gateways_11_dls_client_bootstrapping.fm
DLS Client Bootstrapping
Bootstrapping with "No PIN" PIN Mode
11 DLS Client Bootstrapping

DLS client bootstrapping is a procedure that must be performed once to allow the
DLS server to exchange configuration data with the gateway. This procedure
generates an individual (DLS) certificate for the gateway and transfers it to the
gateway. The gateway and DLS can then use these certificates for unique
reciprocal authentication.
11.1 Bootstrapping with "No PIN" PIN Mode

Variant A:
1. Create a virtual IP device in the DLS under IP Devices > IP Device
Management > IP Device Configuration.
2. Contact the gateway in DLS via IP Devices > IP Device Interaction > Scan
IP Devices. Enter 8084 in the Port field in the "IP Ranges" tab.
If everything is in order, the value Secure appears in the Security Status: field
in the DLS under IP Devices > IP Device Management > IP Device
Configuration > "DLS Connectivity" tab.
Variant B:
Management > IP Device Configuration.
2. Enter the IP address of the DLS server at the gateway with the CLI command
set dls ip_address. The port is usually 18443.
3. Enter the CLI command contact DLS at the gateway.
11.2 Bootstrapping with "Default PIN" or "Individual PIN" PIN Mode

Variant A:
Management > IP Device Configuration > "DLS Connectivity" tab and
then select the required PIN mode.
2. Contact the gateway in DLS via IP Devices > IP Device Interaction > Scan
IP Devices. Enter 8084 in the Port field in the "IP Ranges" tab.
3. Enter the CLI command activate dls pin <pin> at the gateway with
the PIN displayed under 1.
A31003-H3160-S104-8-7620, 07/2014
gateways_11_dls_client_bootstrapping.fm
DLS Client Bootstrapping
Bootstrapping with "Default PIN" or "Individual PIN" PIN Mode
Variant B:
Management > IP Device Configuration > "DLS Connectivity" tab and
then select the required PIN mode.
2. Enter the IP address of the DLS server at the gateway with the CLI command
set dls ip_address. The port is usually 18443.
3. Enter the CLI command contact DLS at the gateway.
4. Enter the CLI command activate dls pin <pin> at the gateway with
the PIN displayed under 1.
A31003-H3160-S104-8-7620, 07/2014
gateways_12_hg3575v4.fm
Gateway HG 3575 - Changing Parameters with AMO STMIB
12 Gateway HG 3575 - Changing Parameters with AMO

STMIB
IMPORTANT: Any of the settings that can be made here with AMOs are read-
only in WBM.
The following branches are supported:
• TYPE GLOBAL - Changing the Idle Bit Pattern
• TYPE IFDATA - Changing the Interface-Specific Parameters of the Access

Point
• TYPE SERVIF - Changing the Login and Password for Service Access
• TYPE ASC - Changing the Payload QoS Setting of the Access Point
• TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size,
Voice Activity Detection and T.38 Fax
• TYP ASC - Transmission of DTMF/Fax/Modem Tones
• TYPE DSP - Jitter Buffer Size of the Access Point
• TYPE DMCDATA - Changing the Access Point Setting to Support Direct

Media Connections
• TYPE H323 - Changing the H323 Settings at the Access Point
• TYPE JB - Configuring the Jitter Buffer
• TYPE SIGQOS - Quality Monitoring for the Signaling Connection over IP
• TYPE SNMP - Changing the Community Strings for Read Access
• TYPE MGNTDATA - Management Data and Backup Server
• TYPE WBMDATA - Changing the Login and Password for WBM
• TYPE GWSECTOR - Changing the Access Point Sector Number for the
Resource Manager
• TYPE DLSDATA - Configuring DLS Data
• TYPE SOCODATA
• TYPE IPCONF
• Resetting the Parameters to Default Values
A31003-H3160-S104-8-7620, 07/2014
TYPE GLOBAL - Changing the Idle Bit Pattern
12.1 TYPE GLOBAL - Changing the Idle Bit Pattern
Configuration Management --> System Data --> IPDA --> IPDA Access
Point
Click Search and select the access point.
Enter idle bit pattern on the General tab and Save.
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,SLOT=99,TYPE=GLOBAL,PATTERN=2
13;
This change does not become effective until the access point is restarted.
Configuration Management --> System Data --> IPDA --> IPDA System
Data
Click Search and select the access point. Click Execute on the Action pull-
down menu and select the mode of action Update AP, confirm with OK.
EXEC-USSU:MODE=UPDATAP,LTU=99;
IMPORTANT: Connections are cleared down without further warning.

Prior to the EXEC-USSU:UPDATAP, the configuration must be updated on the
system hard disk.
12.2 TYPE IFDATA - Changing the Interface-Specific Parameters of the

Access Point
The settings can differ from access point to access point.
The following parameters can be set:
– For the physical Ethernet interface [BITRATE]
– For QoS support on Layer 2 to IEEE 802.1 q/q [VLAN, VLANID]
– For QoS support on Layer 3 to IETF RFC 2474 (DiffServ) 

[TOSLAN, TOSMODEM]
The Ethernet interface setting must be identical for both connected interface
partners (HG 3575 or LAN switches, routers).
IMPORTANT: The setting of a fixed interface partner leads to problems with the
“Autonegotiate“ setting of the other partner.
Incorrect settings cannot normally be detected by the system and therefore go
unreported. If one device is operating in full duplex and the other in half duplex
mode, this is not immediately noticeable. Where there is a high payload, the
A31003-H3160-S104-8-7620, 07/2014
TYPE IFDATA - Changing the Interface-Specific Parameters of the Access Point
device set to half duplex will report a higher number of late collisions and the
packet delay will increase sharply.
If the LAN port connected to the HG 3575 does not support autonegotiation or if
it does not work reliably, fixed values must be set for the HG 3575’s Ethernet
interface.
VLAN tagging should only be activated when all routers in the network segment
of the access point support VLAN tagging. The same applies for the DiffServ
CodePoints. If the routers do not support DiffServ, the standard TOS values must
be configured without DiffServ. If DiffServ is supported, but not the CodePoints,
the values specified by the network carrier must be configured.
Given that some network component vendors only support prioritization with
VLAN ID > 0 pursuant to IEEE 802.1 p/q, the VLAN ID can also be set. The HG
3575 module generally sets the priority bits when the VLAN option is activated.
For values, see Table 3, “TOS values”. According to the standard, the VLAN ID
must then be set to zero, which also happens for the default setting.
In the example, VLAN tagging is deactivated (reset to the default value), the
standard TOS values are configured without DiffServ (see Table 3, “TOS values”)
and the Ethernet interface is set to 10 Mbps half duplex.
Point
Enter the TOS bytes under Layer 2 and Layer 3 on the Quality of Service
tab.
Set the transmission speed and mode on the Ethernet Interface tab and
Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=IFDATA,VLAN=NO,
TOSLAN=20,TOSMODEM=16,BITRATE=100MBFD;
Data
Click Search and select the access point. Click Execute on the Action
pull-down menu and select the mode of action Update AP, confirm with
OK.

system hard disk.
A31003-H3160-S104-8-7620, 07/2014
TYPE SERVIF - Changing the Login and Password for Service Access
12.3 TYPE SERVIF - Changing the Login and Password for Service Access
The HG 3575 allows the connection of a TAP/Service PC via RS232/V.24
interface.
There are two operating modes:
• Terminal Mode
In terminal mode, communication with the HG 3575 Loadware is realized
directly via the Command Line Interface.
IMPORTANT: Two-stage CLI is not supported.
CHANGE-
STMIB:MTYPE=NCUI2,LTU=<LTU>,SLOT=<SLOT>,TYPE=SERVIF,LOGINT
RM=<User login for terminal mode>,LOGINPPP=<User login for
PPP connection>,PASSW=<Password for terminal mode>;
The standard login data is:
Login: TRM (parameter (LOGINTRM)
Password: PUBLIC (parameter PASSW)
After successful login the following message appears:
Welcome to the HG 3575 V4.0 <LW-version> Command Line
Interpreter.
vxTarget>
A list of available commands can be now requested via the local help function
which is available via the help command.
• PPP Mode
In PPP mode, a link between the TAP/Service PC and the customer network
is established via the HG 3575 using the IP address configured with the AMO
APRT, parameter TAIPADDR.
Login (default setting): PPP
Password: No password is required for PPP!
IMPORTANT: For security reasons, the configured password cannot be

exported or regenerated.
The passwords are therefore deleted when a system is regenerated from the
REGEN batch.
Logins and passwords set in the system are always stored in uppercase.
These 3 parameters can be configured differently per module.
A31003-H3160-S104-8-7620, 07/2014
TYPE ASC - Changing the Payload QoS Setting of the Access Point
In the example, the login for AP 17 is set to TERMINAL and SURV, while the
password is set to HG3575:
Point
Enter the user data on the Security tab and Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=17,TYPE=SERVIF,
LOGINTRM=TERMINAL,LOGINPPP=SURV,PASSW2=HG3575;
Data
OK.

system hard disk.
<LW-version>
<LW-version> holds the currently loaded loadware version number.
12.4 TYPE ASC - Changing the Payload QoS Setting of the Access Point
In this branch, the Quality of Service for the payload of an access point can be
configured. The settings can differ from access point to access point. If the
routers do not support DiffServ, the standard TOS value must be configured
without DiffServ. If DiffServ is supported, but not the CodePoints, the value
specified by the network operator must be configured.
In the example, the standard TOS value is set for AP 99 without DiffServ (see also
Table 3, “TOS values”).
Point
Enter the TOS bytes under Layer 3-Diffserv on the Quality of Service tab
and Save.
A31003-H3160-S104-8-7620, 07/2014
TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size, Voice Activity Detection and T.38 Fax
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=ASC,TOSPL=16;
This change is started directly on the access point and is effective immediately
without an interruption in operation.
12.5 TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet
Size, Voice Activity Detection and T.38 Fax
See also Chapter 15, “Codec Settings”.
Codec list
With NCUI2, direct media connections from IP phones, trunking gateways or HG
3500/75 gateways associated with networked HiPath 4000 systems can be
terminated on the board. Unlike for IPDA, the codec type for DMC connections is
not selected using classmarks but rather on the basis of a codec list which
provides the relevant partners with information about the codec types supported
and preferred.
HG 3575 supports two codec types: G.711 and G.729
The sequence in which the codec types are named defines the preference. The
type named first is preferred.
In the example, NCUI2 supports G.711 and G.729 but G.729 is preferred. The
audio sample size for G.711 and G.729A is set to 60 ms.
T.38 Fax
Point
Select G729, G711 on the General tab under DMC Codec List in the
Direct Media Connection section and Save.
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=ASC,PRIO=PRIO1,CODEC=G72
9,RTP=60;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=ASC,PRIO=PRIO2,CODEC=G71
1,RTP=60;
without an interruption in operation.
A31003-H3160-S104-8-7620, 07/2014
TYP ASC - Transmission of DTMF/Fax/Modem Tones
12.6 TYP ASC - Transmission of DTMF/Fax/Modem Tones
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=ASC,RFCFMOIP=YES,RFCDTMF
=YES,REDRFCTN=YES;
REDRFCTN Redundant transmission of the RFC2833 tones in accor-

dance with RFC2198
RFCDTMF Transmission of DTMF tones in accordance with
RFC2833.
RFCFMOIP Transmission of fax/modem tones in accordance with
RFC2833
IMPORTANT: The parameters mentioned above must have the same value
in all IPDA gateways (STMI2/4 with regard to AMO CGWB & NCUI2+/4 with
regard to AMO STMIB). This avoids problems and a common function
across all systems is achieved!
With the introduction of the feature "Codec Switch on the fly" in STMI4/NCUI4/
HiPath 4000 Softgate V6 setting RFCMOIP=NO in AMO CGWB and AMO STMIB
is the better option for fax/modem calls. Therefore, the default value was changed
from YES to NO. There is no necessity to change the parameter in existing
installations.
12.7 TYPE DSP - Jitter Buffer Size of the Access Point

The parameter JITBUFD only takes effect if the parameter JBMODE in the JB
branch is set to 0 (LEGACY MODE). JBMODE=0 (=LEGACY MODE) is no longer
supported as of HiPath 4000 V4. The jitter buffer size therefore no longer needs
to be set.
12.8 TYPE DMCDATA - Changing the Access Point Setting to Support

Direct Media Connections
These parameters are used to set if or how many direct media connections are
permitted simultaneously on a specific HG 3575. The connections are counted
both in the OpenScape 4000 central system’s software and on the board itself.
A31003-H3160-S104-8-7620, 07/2014
TYPE H323 - Changing the H323 Settings at the Access Point
Point
Enter under Direct Media Connection (DMC) enabled on the General tab
and Save.
The access point must be switched off if you want to change the value for
DMCALLWD.
DEACT-USSU:LTU=19;
If you only want to change the number of DMC connections (DMCCONN)
then the access point must not be deactivated.
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=DMCDATA,DMCALLWD=YES,DMC
CONN=30;
This change does not become effective until the access point is restarted or
switched on again.
Data
OK.
IF DMCALLWD has been changed the access point must be switched on
again:
ACT-USSU:LTU=19;
If the number of DMC connections (DMCCONN) has been changed an
UPDATPA must be performed:
IMPORTANT: Connections are cleared down without further warning when

performing UPDATAP.
system hard disk.
12.9 TYPE H323 - Changing the H323 Settings at the Access Point
Direct media connections use the H323 fast connect mechanism to set up
connections. The NCUI2/4 and STMI2/4 platform consequently supports H.323.
Two timers from the H.323 stack and the gateway name can be modified.
Point
Enter under Direct Media Connection (DMC) enabled on the General tab
and Save.
A31003-H3160-S104-8-7620, 07/2014
TYPE JB - Configuring the Jitter Buffer
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=H323,Q931T1=50,
Q931T2=500,GWNAME=“HG3575-2“;
with the next H.323.
12.10 TYPE JB - Configuring the Jitter Buffer

A basic understanding of procedures and configuration parameters is required to
perform jitter buffer configuration. Refer to Section 2.5, “Jitter Buffer”.
The adaptive jitter buffer (JBMODE=2) that reduces delays is set by default.
Point
Enter the parameter on the General tab under Jitter Buffer and click
Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=JB,
AVGDLYV=40,MAXDLYV=120,MINDLYV=20,PACKLOSS=4,
AVGDLYD=60,MAXDLYD=200,JBMODE=2;
These changes are started directly on the access point and become effective
when the next connection is set up.
12.11 TYPE SIGQOS - Quality Monitoring for the Signaling Connection over
IP
Generation
Configuration Management --> System Data --> IPDA --> Access point
Click Search and enter or change the required parameters on the Quality
of Service tab in the Signaling Quality of Service section, then click
Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=SIGQOS,
BANDW=40,MAXRTD=500,MINTHRPT=30,
SIGPTHSW=EXTEND,QOSSTAT=NO;
The setting becomes effective immediately.
IMPORTANT: If the Bandwidth to the shelf is less than 64kbits/s then BANDW
should also be specified accordingly.
If Signaling Survivability is not installed then SIGPTHSW=STD should be used.
A31003-H3160-S104-8-7620, 07/2014
TYPE SNMP - Changing the Community Strings for Read Access
12.12 TYPE SNMP - Changing the Community Strings for Read Access
The HG 3575 board operates an SNMP agent that can be address over LAN.
HG 3575’s SNMP agent exclusively supports read-only access.
Access authorization and access rights are controlled by the SNMP agent over
community strings.
A MIB browser that sends queries to the SNMP agent, identifies itself as
belonging to a community. The community is identified by a community string.
This is a simple, unencrypted text.
The standard setting - and default for community string 1 (CS1) - is “public“, CS2
is not used.
These values can be modified. CS2 can be used to assign read-only access to a
second community on the SNMP agent.
If, for example, CS1=“ToP_SeCrEt23“ is set and CS2=“11!$ZwY?“, access

attempts using all other community strings (including “public“) are rejected.
For the parameters CS1 and CS2, all ASCII characters between «!»
(exclamation mark, 33 Dec) and «~» (tilde, 126 Dec) are used with the exception
of the characters «”» (34 Dec), «/» (47 Dec), «\» (92 Dec), and «^» (94 Dec).
The space character « » (32 Dec) may not be used.
Point
Enter on the Security tab under SNMP and Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=SNMP,
CS1=“ToP_SeCrEt23“,CS2=“11!$ZwY?“;
Data
OK.
IMPORTANT: Connections are cleared down without further warning.
CS1 cannot be deleted. The following procedure is recommended for deleting

CS2:
A31003-H3160-S104-8-7620, 07/2014
TYPE MGNTDATA - Management Data and Backup Server
• Reset all parameters in the SNMP AMO branch to the default value
(CS1=“public“, CS2 inactive)
Initialization can only be initiated in expert mode.

Expert Mode --> HiPath 4000 --> HiPath 4000 Expert Access --> Open
...<IP> with AMO 
(see AMO command)
CHANGE-STMIB:MTYPE=INITNCU2,LTU=99,TYPE=SNMP;
• Restore the required values for CS1
Point
Enter on the Security tab under SNMP and Save.
CHANGE-STMIB:MTYPE=NCUI2,LTU=99,TYPE=SNMP,
CS1=“ToP_SeCrEt23“;
• This change does not become effective until the access point is restarted.
Data
OK.
12.13 TYPE MGNTDATA - Management Data and Backup Server
CHANGE-
STMIB:MTYPE=NCUI2,LTU=<number>,TYPE=MGNTDATA,MGNTIP
=<number>,MGNTPN=<number>,BUSIP=<number>,BUSPN=<num
ber>;
12.14 TYPE WBMDATA - Changing the Login and Password for WBM
WBM access can be configured in this branch.
A31003-H3160-S104-8-7620, 07/2014
TYPE GWSECTOR - Changing the Access Point Sector Number for the Resource Manager
CHANGE-
STMIB:MTYPE=NCUI2,LTU=<LTU>,SLOT=<SLOT>,TYPE=WBMDATA,LO
GINWBM=<User login for WBM
connection>,PASSWWBM=<Password for WBM
connection>,ROLE=<Role of the WBM user; sets access
rights>;
Role Rights
ADMIN Administrator (default value)
ENGR Developer (access to all features)
READONLY Administrator with read-only access
SU Superuser (access to all features)
Table 12 WBM rights

The data for initial login as engr is:
User name: HP4K-DEVEL
Password: 4K-admin
12.15 TYPE GWSECTOR - Changing the Access Point Sector Number for
the Resource Manager
In this branch, the parameter GWSECTNO is used to assign the HG 3575
gateway a sector number from the Resource Manager’s sector concept.
Point
Enter the Gateway Sector Number on the General tab and click Save.
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=GWSECTOR,GWSECTNO=7;
This change becomes effective immediately and without interrupting operation.
12.16 TYPE DLSDATA - Configuring DLS Data
CHANGE-
STMIB:MTYPE=NCUI2,LTU=99,TYPE=DLSDATA,DLSIPADR=<number>
, DLSPORT=<number>,DLSACPAS=<param>;
A31003-H3160-S104-8-7620, 07/2014
TYPE SOCODATA
12.17 TYPE SOCODATA
CHANGE-
STMIB:MTYPE=NCUI2,LTU=<number>,TYPE=SOCODATA,CLAIPA
DR=<number>,CLAPORT=<number>;
12.18 TYPE IPCONF
CHANGE-
STMIB:MTYPE=NCUI2,LTU=<number>,TYPE=IPCONF,IPMODE=<
param>,DHCPV4=<param>,DHCPV6=<param>;
12.19 Resetting the Parameters to Default Values

If the parameters of one or all branches of the NCUI2/4 data are to be reset to
default values, e.g. after being changed temporarily for diagnostic work, this can
be performed in the INITNCU2 branch. The example sets all ASC parameters to
their default values.
Initialization can only be initiated in expert mode.

...<IP> with AMO 
(see AMO command)
CHANGE-STMIB:MTYPE=INITNCU2,LTU=17,TYPE=ASC;
The changes under TYPE ASC, DSP, H323, JB, SNMP, MGNTDATA, WBMDATA
and DLSDATA become effective immediately without interrupting operation.
Changes under TYPE GLOBAL, IFDATA, SERVIF, DMCDATA and SIGQOS

become effective after the access point has been restarted.
This behaviour is also valid for the command CHANGE-

STMIB:MTYPE=INITNCU2,LTU=17, TYPE=ALL;. Therefore it is
recommended to restart the access point after resetting all parameters.
A31003-H3160-S104-8-7620, 07/2014
Resetting the Parameters to Default Values
Data
OK.

system hard disk.
A31003-H3160-S104-8-7620, 07/2014
gateways_13_hg3500v4_install_hints.fm
General Information on How to Configure a HG 3500 Common Gateway
Changing the common gateway configuration
13 General Information on How to Configure a HG 3500

Common Gateway
13.1 Changing the common gateway configuration

Please note that the entire board must be reconfigured if changes are made to
the common gateway configuration.
13.2 AMOs
• The STMI boards are configured iwith the AMO CGWB or, if the IPDA was
set, with the AMO BCSU (see Chapter 16, “Multiple Feature Support
Configuration at the Common Gateway (Example)”).
• The NCUI board is still configured with the AMO STMIB.
• AMO BFDAT is used for block configuration.
• Functions are consolidated on a single board using the AMO BCSU.
• The DB line range of a board must be consecutive.
• All HG 3500 modules must be connected at the HiPath 4000 LAN segment.
• The lines configured for a board cannot be subsequently modified. The entire
board must be reconfigured if additional lines are required on a board.
• The parameter FCTID in the AMO BCSU must always be set to 1.1
13.3 Rules
• The parameter for the functional block (FCTBLK) can be freely assigned. It
may not, however, remain unassigned.
• A completed (configured) functional block may be assigned to one or more

boards.
• The parameter for the boards to be used (BRDBCHL) determines how many
B channels are available to the board.
1. In HiPath 4000 V3.0 and earlier versions, this parameter is used to determine the function of the
STMI board (HFA, IPDA, trunking, etc.). In HiPath 4000 V4 (and later), this is defined with the
AMO BFDAT.
A31003-H3160-S104-8-7620, 07/2014
Rules
If the value BCHAN60&BCHAN120 is set, an STMI1 with 60 or 120 B

channels can be used. This value is also useful if a small STMI with 60 B
channels becomes defective. This can then be replaced with a large STMI
with 120 B channels. It is not possible to replace a large STMI with a small
one.
• Parameter UNITS
– 1 unit corresponds to 10 B channels
– If the number of units (UNITS) is not specified for the configuration, 10 B

channels (UNITS=1) are configured for each circuit.
– Up to three units can be specified for each circuit.
– The total number of B channels for the function is calculated by

multiplying the number of circuits (LINECNT) by the number of B
channels in a unit (UNITS). 
Example: LINECNT=4, UNITS=3. 4 multiplied by 3 multiplied by 10
equals 120 B channels.
• If an IPDA function (HG3570) is to be configured for a multiple feature

configuration, this must be configured first.
• For IPDA, only the number of B channels (BCHLCNT) must be specified.
• For IP trunking, the number of circuits (LINECNT) and the number of units
(UNITS) must be specified.
• For HFA and SIP, the number of circuits (LINECNT) and the number of B
channels (BCHLCNT) must be specified.
IMPORTANT: If reserved HFA or SIP circuits are to be configured, the B

channels designated for this purpose must also be specified here.
This is not necessary for reserved trunk circuits as the assignment is
performed based on the number of units (UNITS).
• For WAML, only the number of units (UNITS) must be specified.
IMPORTANT: Only one circuit is possible for WAML.

This parameter can be omitted if UNITS=1.
• Reserve function
Since the board configuration can only be modified by removing the board, an
option has been created that allows users to reserve circuits for use at a later
stage. If this feature is to be used for the functions HG3530, HG3540 or
1. STMI stands for STMI2 (Q2316-X, Q2316-X10) and STMI4 (Q2324-X500,Q2324-X510)
A31003-H3160-S104-8-7620, 07/2014
Restrictions
HG3550, the relevant function must be configured directly after the actual
function (HG3550&HG3550R, for instance). The Reserve function must
always be specified after the actual function (i.e. at the end).
The combination HG3550&HG3530&HG3550R is not permitted as this would
lead to invalid circuit distribution (Trunk - HFA - Trunk).
It is not possible to configure several Reserve functions on a single board.
The reserved circuits can be subsequently converted to usable circuits with
CHANGE-
BCSU:TYPE=IPGW,LTU=<LTU>,SLOT=<slot>,CHNGRSLN=<number>;
/*<number>: Number of circuits that should be converted to
usable circuits.
IMPORTANT: Now you must reset the board.

RESET-BSSU:ADDRTYPE=PEN,LTU=<ltu>,SLOT=<slot>;
• The STANDBY function can only be configured as a single feature.
• Eleven single-feature standard profiles are configured in the database (see

AMO description, AMO BFDAT).
• You can configure a functional block with

CHANGE-BFDAT:CONFIG=OK,FCTBLK=<number>,ANSW=YES;
You can check the status with DISPLAY-BFDAT:FCTBLK=<number>;
If the configuration of the functional block is complete STATUS=OK is
displayed.
If a configuration error is detected when the block configuration is complete,
the functional block must be deleted (DELETE-
BFDAT:FCTBLK=<number>,ANSW=YES;) and reconfigured.
If the configuration of a functional block is not complete STATUS=CONT is
displayed. The functional block may not be assigned to a board. This is
refused by the AMO BCSU with the Fault message F89.
Fault message F89

F89: THE SPECIFIED FUNCTION BLOCK IS NOT YET FULLY CONFIGURED:
PLEASE COMPLETE THE CONFIGURATION FIRST WITH THE AMO BFDAT.
13.4 Restrictions
• Only one trunking protocol can be configured for each board (AMO CGWB).
There are no restrictions on interworking with other functions.
A31003-H3160-S104-8-7620, 07/2014
Overview of Configuration Steps
• The entire board must be reconfigured if the changes are made to the
configuration.
13.5 Overview of Configuration Steps

An overview of the configuration steps for a HG 3500 common gateway is
provided below:
1. Configure functional blocks with the AMO BFDAT (Assistant: Configuration

Management > System Data > Board > CGW Functional Block)
2. Assign the functional block to a board using the AMO BCSU (Assistant:
Configuration Management > System Data > Board > Board)
3. Administrate features using the AMO CGWB
A31003-H3160-S104-8-7620, 07/2014
Gateway HG 3500 - Changing Parameters with AMO CGWB
TYPE ASC - Changing the Payload QoS Setting in Host System
14 Gateway HG 3500 - Changing Parameters with AMO

CGWB
IMPORTANT: Any of the settings that can be made here with AMOs are read-
only in WBM.
The following branches are supported:
• TYPE ASC - Changing the Payload QoS Setting in Host System
• TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size,
and Voice Activity Detection
• TYP ASC - Transmission of DTMF/Fax/Modem Tones
• TYPE DMCDATA - Changing the HG 3500 Setting to Support Direct Media

Connections
• TYPE DSP - Changing the DSP (Signal Processor) Setting at an HG 3500
• TYPE GLOBIF - Changing the Idle Bit Pattern and Interface-Specific

Parameters
• TYPE GWSECTOR - Changing the HG 3500 Sector Number for the

Resource Manager
• TYPE H235DATA - H.235-Security
• TYP MGNTDATA - Connection to the HiPath 4000 Assistant
• TYPE SERVIF - Changing the Login and Password for the Service Access
• TYPE WBMDATA - Changing the Login and Password for WBM
• TYPE JB - Configuring the Jitter Buffer
• TYPE IPCONF
• Resetting the Parameters to Default Values
14.1 TYPE ASC - Changing the Payload QoS Setting in Host System
In this branch, the Quality of Service for the payload of an access point can be
configured. The settings can differ from HG 3500 to HG 3500. If the routers do
not support DiffServ, the standard TOS value must be configured without DiffServ.
If DiffServ is supported, but not the CodePoints, the value specified by the
network operator must be configured.
A31003-H3160-S104-8-7620, 07/2014
TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet Size, and Voice Activity Detection
In the example, the standard TOS value is set for HG 3500 in LTU 5, mounting
slot 91 without DiffServ (see also Table 3, “TOS values”).
Data
Enter settings under Payload Connections on the System Data tab and
click Save.
CHANGE-CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=ASC,TOSPL=16;
This change is loaded directly to the board and is effective immediately without
interrupting operation.
14.2 TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet
Size, and Voice Activity Detection
See also Chapter 15, “Codec Settings”.
This branches' parameters only apply to one HG 3500 board. Therefore each HG
3500 board could be configured differently in a HiPath 4000 system.
To ensure the usability and the correct diagnosis of the system, these parameters
must have identical settings (FUNCTION=HG3570) for all HG 3500 boards.
In the example, the audio sample size for G.711 and G.729 is set to 60 ms for the
common gateway HG 3500 1-5-91. This results in a higher packeting delay, but
a comparatively low transmission bandwidth requirement.
Configuration Management --> System Data --> Board --> Board

Click Search and select STMI.
Set the times for G.711 and G.729 on the STMI Board Data tab and click
Save.
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=ASC,PRIO=PRIO1,CODEC
=G711,RTP=60;
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=ASC,PRIO=PRIO2,CODEC
=G729,RTP=60;
These changes are loaded directly to the HG 3500 and become effective
immediately without interrupting operation.
A31003-H3160-S104-8-7620, 07/2014
TYP ASC - Transmission of DTMF/Fax/Modem Tones
14.3 TYP ASC - Transmission of DTMF/Fax/Modem Tones
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=ASC,RFCFMOIP=YES,RF
CDTMF=YES,REDRFCTN=YES;
REDRFCTN Redundant transmission of the RFC2833 tones in accor-

dance with RFC2198
RFCDTMF Transmission of DTMF tones in accordance with
RFC2833.
RFCFMOIP Transmission of fax/modem tones in accordance with
RFC2833
in all IPDA gateways (STMI2/4 with regard to AMO CGWB & NCUI2+/4 with
regard to AMO STMIB). This avoids problems and a common function
across all systems is achieved!
With the introduction of the feature "Codec Switch on the fly" in STMI4/NCUI4/
HiPath 4000 Softgate V6 setting RFCMOIP=NO in AMO CGWB and AMO STMIB
is the better option for fax/modem calls. Therefore, the default value was changed
from YES to NO. There is no necessity to change the parameter in existing
installations.
14.4 TYPE DMCDATA - Changing the HG 3500 Setting to Support Direct

Media Connections
Use this parameter to set the number of simultaneous direct media connections
permitted on a certain HG 3500. The connections are counted both in the HiPath
4000 central system’s software and on the board itself.
A31003-H3160-S104-8-7620, 07/2014
TYPE DSP - Changing the DSP (Signal Processor) Setting at an HG 3500

Make the settings on the STMI Board Data tab under Number of DMC
connections and Save.
Configuration Management --> System Data --> Maintenance -->

Board Maintenance
Click Execute on the Action pull-down menu, select Restart and confirm
with OK.
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=DMCDATA,DMCCONN=30;
This change does not become effective on the HG 3500 until this board is
restarted with
RESTART-BSSU:ADDRTYPE=PEN,LTU=5,SLOT=91.
IMPORTANT: Existing links are disconnected.
14.5 TYPE DSP - Changing the DSP (Signal Processor) Setting at an HG

3500
The parameter JITBUFD only takes effect if the parameter JBMODE in the JB
branch is set to 0 (LEGACY MODE). JBMODE=0 (=LEGACY MODE) is no longer
supported as of HiPath 4000 V4. The jitter buffer size therefore no longer needs
to be set.
The parameter VADEN is no longer valid. To configure Voice Activity Detection,

you should use the parameter branch TYPE=ASC, parameter VAD (see Section
14.2, “TYPE ASC - Setting the Codec List for DMC Connections, RTP Packet
Size, and Voice Activity Detection”).
14.6 TYPE GLOBIF - Changing the Idle Bit Pattern and Interface-Specific
Parameters
The setting for the physical Ethernet interface may be different for individual HG
3500s.
partners (HG 3500 or LAN switches, routers).
"Autonegotiate" setting of the other partner.
Incorrect settings cannot normally be detected by the system and therefore go
A31003-H3160-S104-8-7620, 07/2014
TYPE GWSECTOR - Changing the HG 3500 Sector Number for the Resource Manager
unreported. If one device is operating in full duplex and the other in half duplex
mode, this is not immediately noticeable. Where there is a high payload, the
device set to half duplex will report a higher number of late collisions and the
packet delay will increase sharply.
If the LAN port connected to the HG 3500 does not support autonegotiation or if
it does not work reliably, fixed values must be set for the HG 3500’s Ethernet inter-
faces.
The QoS-relevant parameters are set identically for all HG 3500 modules
together with SL100/200 via the AMO SIPCO.
In the example, the Ethernet interface is set to 10 Mbps half duplex and the idle
bit pattern is set to 213.

Click Search and select Board Name=STMI2 or Board Name=STMI4.
Enter appropriate settings on the STMI Board Data tab and click Save.

Board Maintenance
with OK.
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=GLOBIF,PATTERN=213,
BITRATE=100MBFD;
This change does not become effective on the HG 3500 until this board is
restarted with 
14.7 TYPE GWSECTOR - Changing the HG 3500 Sector Number for the
Resource Manager
In this branch, the parameter GWSECTNO is used to assign the HG 3500
gateway a sector number from the Resource Manager’s sector concept.

Make the settings on the STMI Board Data tab under Gateway Sector
Number and Save.
CHANGE-
CGWB:MTYPE=CGW,LTU=5,SLOT=91,TYPE=GWSECTOR,GWSECTNO=1;
This change becomes effective immediately and without interrupting operation.
A31003-H3160-S104-8-7620, 07/2014
TYPE H235DATA - H.235-Security
14.8 TYPE H235DATA - H.235-Security

The H.235 security feature is designed to prevent unauthorized devices setting
up connections to a HG 3500 gateway. An example of such a scenario would be
a Netmeeting client that wishes to use a HG 3500.
The security concept is based on two mechanisms: When the features are
activated, HG 3500 sends a token in each signaling packet (consisting of a
password and key, defined in AMO CGWB), to authenticate itself to a receiving
HG 3500 gateway.
In the AMO CGWB a time frame is set. By default, the difference between the time
stamp of an arriving H.323 signaling packet and the current time of the receiving
HG 3500 cannot exceed 10 seconds.
A time sever is thus required for this feature. If the gateways are in other time
zones, this must be set on the HG 3500 boards.
Generation
To activate the H.235 security feature on the board, you set the security flag using
the AMO ZANDE. This activates H.235 data in the AMO CGWB on the board.
CHANGE-ZANDE:ALLDATA,H235SEC=YES;
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu no>,SLOT=<slot
no>,TYPE=H235DATA,SECSUBS=YES,SECTRNK=YES
GLOBID1=<string>,GLOBID2=<string>,TIMEWIN=<number>,GL
OBPW=<number>};;
IMPORTANT: Once you have activated the H.235 security feature with the AMO
ZANDE, you must reboot the board to activate the changes.
IMPORTANT: The SECSUBS and SECTRNK parameters in the AMO CGWB

must always be configured identically. Otherwise the AMO outputs an Error
message.
Error message
H41: The parameters SECSUBS and SECTRNK must be configured
identical.
Therefore the parameters are re-configured (SECTRNK is master if
needed).
A31003-H3160-S104-8-7620, 07/2014
TYP MGNTDATA - Connection to the HiPath 4000 Assistant
14.9 TYP MGNTDATA - Connection to the HiPath 4000 Assistant

The branch TYPE=MGNTDATA is used to set up the connection to HiPath 4000
Assistant.This is among other things necessary for the auto restorefunction of the
HG 3500.
For trunking connections to OpenScape Voice the parameters MGNTPN and

BUSPN are important.
CHANGE-CGWB:MTYPE=MGNTDATA,MGNTIP=<ip-address
UW7>,MGNTPN=<port number of UW7>,BUSIP=<ip-address
UW7>,BUSPN=<port number of the backup server>;
This command sets up two IP addresses (+ports):
The first IP address MGNTIP designates the „Management Station“. This is the
IP address under which the HiPath 4000 Assistant can be reached. This IP
address is important for the single login concept. Logging on to the HG 3500 via
the HiPath 4000 Assistant is only possible via this IP address.
The second IP address BUSIP defines the HiPath 4000 Assistant backup server
that is contacted by the HG 3500 at startup during the auto restore.
IMPORTANT: After a reload of the board the values for the ports (MGNTPN and
BUSPN) are not restored. They are set to default. This leads to problems in
connection with trunking.
14.10 TYPE SERVIF - Changing the Login and Password for the Service
Access
In the parameter tree TYPE=SERVIF you can define the access data for the
Command Line Interface.
For more information on CLI please refer to Chapter 18, “Command Line
Interface CLI in HG 3500”.
CHANGE-
CGWB:MTYPE=CGW,LTU=<LTU>,SLOT=<SLOT>,TYPE=SERVIF,LOGIN
TRM=<User login for terminal mode>,PASSW=<Password for
terminal mode>;
The standard login data is:

Login: TRM (parameter (LOGINTRM)
Password: PUBLIC (parameter PASSW)
A31003-H3160-S104-8-7620, 07/2014
TYPE WBMDATA - Changing the Login and Password for WBM
14.11 TYPE WBMDATA - Changing the Login and Password for WBM
WBM access can be configured in this branch.
CHANGE-
CGWB:MTYPE=CGW,LTU=<LTU>,SLOT=<SLOT>,TYPE=WBMDATA,LOGI
NWBM=<User login for WBM connection>,PASSWWBM=<Password
for WBM connection>,ROLE=<Role of the WBM user; sets
access rights>;
Role Rights
ADMIN Administrator (default value)
ENGR Developer (access to all features)
READONLY Administrator with read-only access
SU Superuser (access to all features)
Table 13 WBM rights

The data for initial login as engr is:
User name: HP4K-DEVEL
Password: 4K-admin
14.12 TYPE JB - Configuring the Jitter Buffer

A basic understanding of procedures and configuration parameters is required to
perform jitter buffer configuration. Refer to Section 2.5, “Jitter Buffer”.
The adaptive jitter buffer that reduces delays is set by default.
Point
Enter the parameter on the General tab under Jitter Buffer and Save.
CHANGE-CGWB:MTYPE=CGWB,LTU=5,SLOT=91,TYPE=JB,
AVGDLYV=40,MAXDLYV=120,MINDLYV=20,PACKLOSS=4,
AVGDLYD=60,MAXDLYD=200, JBMODE=2;
WBM Explorers > Payload > HW Modules > Edit DSP Jitter Settings
These changes are started directly on the access point and become effective
when the next connection is set up.
A31003-H3160-S104-8-7620, 07/2014
TYPE IPCONF
14.13 TYPE IPCONF
14.14 Resetting the Parameters to Default Values

If the parameters of one or all branches of the STMI2/4 data are to be reset to
default values, e.g. after being changed temporarily for diagnostic work, this can
be performed in the INITCGW branch. The example sets all DMCDATA
parameters to their default values.
Initialization and reloading (where required) can only be performed in

expert mode.
...<IP> using AMO 
(see AMO command)
CHANGE-CGWB:MTYP=INITCGW,LTU=5,EBT=91,TYP=DMCDATA;
The changes under TYPE ASC, DSP, MGNTDATA, SIPTRERH, WBMDATA,

DLSDATA and JB become effective immediately without interrupting operation.
Changes under TYPE DMCDATA, GKDATA, GLOBIF, GWDATA, GWSECTOR,

H235DATA, SIPTRSSA and DLSDATA become effective after the HG 3500
has been restarted with
DLSDATA
DLSIPADR & DLSPORT : become effective after CGW restart
DLSACPAS : become effective immediately without interrupting operation
A31003-H3160-S104-8-7620, 07/2014
Resetting the Parameters to Default Values
A31003-H3160-S104-8-7620, 07/2014
gateways_15_codec.fm
Codec Settings
HFA and Trunking
15 Codec Settings
15.1 HFA and Trunking

A priority list of the codecs is configured in the AMO CGWB for HG 3500, and
accordingly in the AMO STMIB for HG 3575. During codec negotiations, the
gateways use the codecs configured in this way.
Examples:
• Gateway is a DMC endpoint
• Master connections for HFA and IP trunking
Example
• HG 3500 (STMI)
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,UDPPRTLO=29100,TOSPL=0,
TOSSIGNL=0,T38FAX=YES,RFCFMOIP=YES,RFCDTMF=YES,REDRFCTN=YES,P
RIO=PRIO1,CODEC=G711,VAD=YES,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO2,CODEC=G711U,
VAD=YES,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO3,CODEC=G729A,
VAD=NO,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO4,CODEC=G729B,
VAD=YES,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO5,CODEC=G729AB
,VAD=YES,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO6,CODEC=NONE,V
AD=NO,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=3,SLOT=11,TYPE=ASC,PRIO=PRIO7,CODEC=NONE,V
AD=NO,RTP="20";
• HG 3575 (NCUI)
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,TOSPL=48,PRIO1,CODEC=G771,V
AD=YES,RTP="20";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO2,CODEC=G771U,VAD=
YES,RTP="20";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO3,CODEC=G729AB,VAD
=YES,RTP="40";
A31003-H3160-S104-8-7620, 07/2014
gateways_15_codec.fm
Codec Settings
IPDA
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO4,CODEC=G729B,VAD=
YES,RTP="20";
CHA-STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO5,CODEC=NONE;
15.2 IPDA
For IPDA, the codecs for the master connection are switched by DNIL and
configured in AMO SDAT / AMO TDCSU, etc., i.e. in the user/trunk data of the
affected devices (see IP Distributed Architecture (IPDA), Section 2.4,
“Subscriber, CO/Tie Trunk Circuits in Access Points”).
IMPORTANT: This means that the codecs do not need to be configured in the
AMOs CGWB and STMIB for the IPDA master connection.
For IPDA connections, the codecs are configured as previously described in the
AMOs STMIB or CGWB (see also Section 12.5, “TYPE ASC - Setting the Codec
List for DMC Connections, RTP Packet Size, Voice Activity Detection and T.38
Fax”, Section 14.2, “TYPE ASC - Setting the Codec List for DMC Connections,
RTP Packet Size, and Voice Activity Detection” bzw. Section 12.6, “TYP ASC -
Transmission of DTMF/Fax/Modem Tones”).
IMPORTANT: The RFCFMOIP, RFCDTMF and REDRFCTN parameters in the

TYP=ASC branch must have the same value in all IPDA gateways (STMI2/4 with
regard to AMO CGWB & NCUI2+/4 with regard to AMO STMIB). This avoids
problems and a common function across all systems is achieved!
A31003-H3160-S104-8-7620, 07/2014
gateways_16_multiple_feature_sup.fm
Multiple Feature Support Configuration at the Common Gateway (Example)
Important Information / Restrictions
16 Multiple Feature Support Configuration at the Common

Gateway (Example)
16.1 Important Information / Restrictions

• IPDA 
If the function IPDA (HG3570) is configured on an STMI board, the IP address
of the common gateway must be assigned with the AMO BCSU. For all other
functions of the board, the IP address must be assigned with the AMO
CGWB.
• IPDA 
If several functions are defined in a function block (IPDA and others), the IP
address for IPDA must be set with AMO BCSU, for the other functions the
same IP address must be configured using the AMO CGWB!
• VLAN settings in AMO CGWB: When MFS is configured, the following

AMOs are used:
– MFS with IPDA functionality: AMO SIPCO
– MFS without IPDA functionality: AMO CGWB
• Trunking protocols 
Only one trunking protocol can be configured for each common gateway
board (either SIP or H323)! If both protocols should be used for trunking,
individual boards must be used.
• IPDA/WAML
No support of WAML and HG3570 (IPDA) functionality on one common
gateway board because it causes path problems at APNW access points.
• HFA/H323 IP Trunking 
The configuration is supported but in case WL2 is used for HFA there will be
problems with common H323 stack timer (Q931responseTimeOut) which
results in unexpected/unwanted logoffs with reason “No bearer channel could
be established”.
Therefore WL2 should not be used at MFS boards with H323 IP trunking
configuration! SIP-Q should be used instead!
• HFA only configuration --> Q931responseTimeOut = 10 sec. (no MFS)
• H323 ony configuration --> Q931responseTimeOut = 3 sec. (no MFS)
• HFA&H323 trunking config. --> Q931responseTimeOut = 3 sec. (not

suitable for WL2)
A31003-H3160-S104-8-7620, 07/2014
Configuring Functional Blocks with the AMO BFDAT
• HFA&SIPQ trunking config. --> Q931responseTimeOut = 10 sec.

(suitable for WL2)
• Trunking protocols 
Only one trunking protocol can be configured for each common gateway
board (either SIP or H323)! If both protocols should be used for trunking,
individual boards must be used. Additionally please note that all Trunks
on an IP Trunking board must share the same COT/COP/COS values -
this is because incoming calls can use any of the configured trunks using
Any Channel search and therefore very important to have consistent
configuration.
16.2 Configuring Functional Blocks with the AMO BFDAT

• Functional block 1: IPDA (HG3570)
• Functional block 2: IPDA (HG3570), IP trunking (HG3550) and HFA

subscriber (HG3530)
• Functional block 3: IPDA (HG3570), IP trunking (HG3550), WAML and HFA

subscriber (HG3530)

subscriber (HG3530)

subscriber (HG3530)
• Functional block 6: IP trunking (HG3550) and HFA subscriber (HG3530)
• Functional block 7: IP trunking, HFA subscriber (HG3530) and reserve HFA

subscriber (HG3530R)
Functional block 1
/* Functional block 1: Adding the IPDA function (HG3570)
ADD-BFDAT:FCTBLK=1,FUNCTION=HG3570,BRDBCHL=BCHAN120;
>>>>> IPDA with 120 B channels
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3570,BCHLCNT=120;
>>>>> End configuration of this block
Functional block 2
/* Functional block 2: Adding the functions IPDA (HG3570), IP trunking (HG3550)
and HFA subscriber (HG3530)
ADD-BFDAT:FCTBLK=2,FUNCTION=HG3570&HG3550&HG3530,BRDBCHL=BCHAN;
A31003-H3160-S104-8-7620, 07/2014
>>>>> IP trunking with one circuit with three units (=30 B channels)
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=2,FUNCTION=HG3550,LINECNT=1,UNITS=3;
>>>>> HFA with 60 circuits with 60 B channels
CHANGE-
;
Functional block 3
/* Functional block 3: Adding the functions IPDA (HG3570), IP trunking
(HG3550), WAML and HFA subscriber (HG3530)
ADD-
BFDAT:FCTBLK=3,FUNCTION=HG3570&HG3550&WAML&HG3530,BRDBCHL=BCHAN1
20;
>>>>> IP trunking with one circuit with three units (=30 B channels)
CHANGE-
>>>>> WAML
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=3,FUNCTION=WAML,UNITS=3;
CHANGE-
;
Functional block 4
ADD-
20;
>>>>> IP trunking with one circuit with one unit (=10 B channels)
A31003-H3160-S104-8-7620, 07/2014
CHANGE-
>>>>> WAML with one unit (=10 B channels)
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=4,FUNCTION=WAML;
CHANGE-
;
>>>>> End configuration of block
Functional block 5
ADD-
20;
>>>>> IP trunking with one circuit with 10 B channels
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=5,FUNCTION=HG3550,LINECNT=1;
CHANGE-
0;
Functional block 6
/* Functional block 6: Adding the functions IP trunking (HG3550) and HFA
subscriber (HG3530)
ADD-BFDAT:FCTBLK=6,FUNCTION=HG3550&HG3530,BRDBCHL=BCHAN120;
>>>>> IP trunking with one circuit with 30 B channels
CHANGE-
CHANGE-
;
A31003-H3160-S104-8-7620, 07/2014

Functional block 7
/* Functional block 7: IP trunking, HFA subscriber function (HG3530) and reserve
HFA subscriber (HG3530R)
IMPORTANT: The reserved HFA B channels must be specified during configu-

ration of the HG3530 function as subscriber B channels are not accepted during
reservation.
ADD-
BFDAT:FCTBLK=7,FUNCTION=HG3550&HG3530&HG3530R,BRDBCHL=BCHAN120;
>>>>> HFA with 80 circuits with 80 B channels and 20 reserve B channels
CHANGE-
0;
>>>>> Reserve HFA subscriber with 20 circuits
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=7,FUNCTION=HG3530R,LINECNT=20;
>>>>> IP trunking with 10 circuits with one unit (=10 B channels)
CHANGE-
Displaying all functional blocks

DISPLAY-BFDAT;
H500: AMO BFDAT STARTED
--------------------------------------------------------------------------------
| FCTBLK = 1 BRDBCHL: BCHAN120 STATUS= OK |
--------------------------------------------------------------------------------
| 1st FUNCT : HG3570 1 LINES UNITS ?? BCHLCNT 120 TOTAL BCHAN 120 |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| FCTBLK = 2 BRDBCHL : BCHL120 STATUS= OK |
--------------------------------------------------------------------------------
| 1st FUNCT : HG3570 1 LINES UNITS 30 BCHLCNT 30 TOTAL BCHAN 30 |
| 2nd FUNCT : HG3550 1 LINES UNITS 3 BCHLCNT 30 TOTAL BCHAN 30 |
| 3rd FUNCT : HG3530 60 LINES UNITS 60 BCHLCNT 60 TOTAL BCHAN 60 |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| 3rd FUNCT : WAML 1 LINES UNITS 3 BCHLCNT 30 TOTAL BCHAN 30 |
| 4th FUNCT : HG3530 30 LINES UNITS 30 BCHLCNT 30 TOTAL BCHAN 30 |
--------------------------------------------------------------------------------
A31003-H3160-S104-8-7620, 07/2014
Configuring the Common Gateway Board with the AMO BCSU
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| FCTBLK = 5 BRDBCHL : BCHL120 STATUS= CONT |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
| 2nd FUNCT : HG3530R 20 LINES UNITS 20 BCHLCNT 0 TOTAL BCHAN 0 |
| 3rd FUNCT : HG3550 10 LINES UNITS 10 BCHLCNT 10 TOTAL BCHAN 10 |
--------------------------------------------------------------------------------
AMO-BFDAT-54 CONFIGURATION OF FUNCTIONAL BLOCKS FOR CGW BOARDS
DISPLAY COMPLETED;
<
16.3 Configuring the Common Gateway Board with the AMO BCSU
Assignment for functional block 1
ADD-BCSU:TYPE=IPGW,LTG=1,LTU=2,SLOT=37,PARTNO=Q2316-
X10,FCTID=1,FCTBLK=1,IPADDR=198.16.16.45;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2;
H500: AMO BCSU STARTED
ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
19 | Q2258-X ACGEN 0|*| AVAILABLE | | NPR
25 | Q2205-X WAML 1 A 0|*| | | NPR
A31003-H3160-S104-8-7620, 07/2014
31 | AVAILABLE 0| | AVAILABLE | |
37 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 198. 16. 16. 45 B-CHANNELS : 120 BCHLCNT : 2
| BLOCK NO : 1 PRERESERVED LINES ASSIGNED : NO
| 1st FUNCT : STMI2-IPDA 1 LINES B-CHANNELS : 120 BCHLCNT : 2
+--------------------------------+-+------------+------------+------------
43 | Q6401-X PBCDG-FU 3 A 0|*| | | NPR
55 | Q2214-X TMOM2 A 0|*| | | NPR
61 | Q2195-X DIU-N4 1 A 0|*| | | NPR
67 | 0| | | |
73 | Q2248-X LTUCE 0|*| AVAILABLE | | NPR
79 | Q2096-X200 DIU-S2 A 0|*| | | NPR
85 | Q2096-X200 DIU-S2 A 0|*| | | NPR
91 | Q2096-X200 DIU-S2 A 0|*| | | NPR
97 | Q2096-X200 DIU-S2 A 0|*| | | NPR
115 | Q2096-X200 DIU-S2 A 0|*| | | NPR
121 | Q2174-X STMD A 0|*| | | NPR
DISPLAY COMPLETED;






Converting reserved HFA circuits to usable circuits
CHANGE-BCSU:TYPE=IPGW,LTG=1,LTU=1,SLOT=61,CHNGRSLN=13;
DISPLAY-BCSU:TYPE=TBl,LTG=1,LTU=1;
A31003-H3160-S104-8-7620, 07/2014

-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
19 | Q7065-X APPS 0|*| AVAILABLE | | NPR
25 | Q2117-X SLMS A 0|*| | | NPR
31 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
| 2nd FUNCT : STMI2-IPGW 1 LINES B-CHANNELS : 30 BCHLCNT : 30
| 3rd FUNCT : STMI-HFA2 60 LINES B-CHANNELS : 60 BCHLCNT : 60
+--------------------------------+-+------------+------------+------------
37 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
| BLOCK NO : 3 PRERESERVED LINES ASSIGNED NO
| 3rd FUNCT : STMI2-WAML 1 LINES B-CHANNELS : 30 BCHLCNT : 30
| 4th FUNCT : STMI-HFA2 30 LINES B-CHANNELS : 30 BCHLCNT : 30
+--------------------------------+-+------------+------------+------------
43 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
+--------------------------------+-+------------+------------+------------
49 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
+--------------------------------+-+------------+------------+------------
55 | Q2316-X10 STMI2 1 A 0|*| | | NPR
+--------------------------------+-+------------+------------+------------
| 1st FUNCT : STMI2-IPGW 1 LINES B-CHANNELS : 30 BCHLCNT : 30
| 2nd FUNCT : STMI-HFA2 90 LINES B-CHANNELS : 90 BCHLCNT : 90
+--------------------------------+-+------------+------------+------------
A31003-H3160-S104-8-7620, 07/2014
Configuring SIP Trunking
61 | Q2316-X10 STMI2 1 A 0|*| | | NPR

+--------------------------------+-+------------+------------+------------
| BLOCK NO : 7 PRERESERVED LINES ASSIGNED : YES
| 1st FUNCT : STMI-HFA2 93 LINES B-CHANNELS : 100 BCHLCNT : 100
| 2nd FUNCT : STMI-HFA2R 7 LINES B-CHANNELS : 0 BCHLCNT : 0
| 3rd FUNCT : STMI2-IPGW 10 LINES B-CHANNELS : 10 BCHLCNT : 10
+--------------------------------+-+------------+------------+------------
73 | Q2248-X LTUCE 0|*| AVAILABLE | | NPR
79 | Q2164-X SLMO16 1 A 0|*| | | NPR
85 | Q2168-X SLMO24 1 A 0|*| | | NPR
91 | Q2153-X100 SLMQ A 0|*| | | NPR
97 | Q2150-X SLMB A 0|*| | | NPR
103 | Q2480-X SLMAR A 0|*| | | NPR
109 | Q2246-X SLMA24 A 0|*| | | NPR
115 | Q2025-X300 TMBD A 0|*| | | NPR
AMO-BCSU -54 BOARD CONFIGURATION, SWITCHING UNIT
DISPLAY COMPLETED;
Seven common gateway boards (in this case: Q2316-X10, STMI2) have been
configured.
16.4 Configuring SIP Trunking

Configuring SIP trunking on the STMI2 board in 1-1-55:
ADD-
CGWB:LTU=1,SLOT=55,SMODE=NORMAL,IPADDR=198.16.16.55,NETMASK=255.
255.255.0,TRPRSIP=30;
IMPORTANT: Only one trunking protocol can be configured for each common
gateway board.
16.5 Completed and Uncompleted Functional Block
16.5.1 Uncompleted functional block

ADD-
20;
A31003-H3160-S104-8-7620, 07/2014
Completed and Uncompleted Functional Block

>>>>> IP trunking with one circuit and one unit (=10 B channels)
CHANGE-
>>>>> HFA with 70 circuits and 70 B channels
CHANGE-
;
>>>>> Do not end configuration of block
CHANGE-BFDAT:CONFIG=OK,FCTBLK=4,ANSW=NO;
Displaying a functional block

DISPLAY-BFDAT:FCTBLK=4;
--------------------------------------------------------------------------------
| FCTBLK = 4 BRDBCHL : BCHL120 STATUS= CONT |
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
AMO-BFDAT-54 CONFIGURATION OF FUNCTIONAL BLOCKS FOR CGW
BOARDS
DISPLAY COMPLETED;

F89: THE GIVEN FUNCTIONAL BLOCK IS NOT COMPLETELY CONFIGURED.
PLEASE FINISH CONFIGURATION BY MEANS OF AMO_BFDAT FIRST.
ADD NOT COMPLETED;
IMPORTANT: If the configuration of a functional block with the AMO BFDAT is

not completed, the block cannot be assigned to any board with the AMO BCSU.
The functional block must be completely configured with the AMO BFDAT before
the command can be successfully run.
A31003-H3160-S104-8-7620, 07/2014
16.5.2 Completed configuration block

Displaying a functional block

DISPLAY-BFDAT:4;
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
AMO-BFDAT-54 CONFIGURATION OF FUNCTIONAL BLOCKS FOR CGW BOARDS
DISPLAY COMPLETED;

H01: BD 1.1 . 43 ASSIGNED
ADD COMPLETED;
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
gateways_17_resource_manager.fm
Resource Manager Functionality
General
17 Resource Manager Functionality
17.1 General
With the resource management for the features HFA (without the feature HFA
Mobile) and IPDA and DMC there are two different methods of resource
administering, observing and evaluating:
• The available bandwidth in certain sectors of a network and the exploitation

by connections and
• the (DSP) channels of the gateways.
The resource Manager (RM) exists in every HiPath 4000 system since V2.0 up to
the latest release and is always active. For the calculation of the bandwidth
required, the RM has to have knowledge of the current topology of the IP network.
If the topology is not configured, then the RM assumes that infinite bandwidth is
available.
For what RM is necessary?

A kind of resource Management was already available in HiPath 4000 V1.0 for
IPDA. The number of B channels, which are connected to the customer IP net,
can be limited for a HG 3570/3575 board. But this method, which is still available,
can not be used for all configurations.
• HFA phones in a company branch behind a WAN connection with limited

bandwidth can only be controlled by the Resource Manager. SIP subscriber
can be used as well. The configuration of SIP subscriber in the AMOs are
identically to HFA subsribers.
• Several access points IP installed in one location, which are connected via a
WAN with limited bandwidth to the Host (the path to the Host must be limited,
not the calls between the access points).
The following concepts Sector and cluster are essential for the broader
understanding of the function.
17.2 Key Terms
17.2.1 Sector
A sector is a section of a customer network defined at the network planning stage
which is regarded in the framework of the resource management.
A31003-H3160-S104-8-7620, 07/2014
Key Terms
A sector can be assigned to either a gateway or an arbitrary section in the IP

network.It is left to the user which physical equipment in the network combine to
form a sector.In order not to complicate the administration, it is reasonably large,
summarizing broadband sections and concentrating itself on particularly resource
weak sections (e.g. narrowband connections in the WAN).
Sector definitions
• LAN sectors are sectors with unlimited bandwidth
• WAN sectors have a limited bandwidth and connect the LAN sectors
• Gateway (GW) sectors are sectors in HG 3570/3575
• HFA sectors are LAN sectors to which a HFA phone is connected
17.2.2 Cluster
The location of endpoints in the network is determined by their membership of a
sector. To simplify the administration the endpoints (devices, trunks) that have the
same accessibility are combined in a so called cluster. A cluster can contain:
• all HFA devices in the HiPath 4000 system
• all HFA devices in one access point
A31003-H3160-S104-8-7620, 07/2014
Key Terms
TDM
CL 1 HG 3500
(Mode: HG 3530)
HFA
HG 3500 SECTOR S213

(Mode: HG 3570)
SECTOR 202
Node x
TDM
SECTOR
HG 3500 SECTOR S220
201
(Mode: HG 3575)
AP 20
TDM
HG 3575) SECTOR S221
HG 3500
(Mode: HG 3530) HFA
SECTOR 200 SECTOR CL 2
AP 21 222
Figure 18 Sector /cluster definition in one HiPath 4000 node (example)
HFA terminals can be assigned to different clusters even though they are
configured on the same board.This is the case when the terminals are connected
to different local area network/WAN sectors.
17.2.3 Sector Path

A sector path is the description of a way through the Customers LAN and WAN
between two enpoints. A sector path is always defined from the perspective of the
system for reaching a gateway sector or a LAN/WAN sector.
A31003-H3160-S104-8-7620, 07/2014
Key Terms
17.2.4 Definitions
17.2.4.1 AMO GKTOP: Parameters in the Branch

TYPE=RESMGMT1
In principle, a distinction is made between the 2 sector types.
One sector type describes a gateway (GW), the other an IP segment of the
customer’s network (LAN or WAN), which have respectively to be established as
sector attributes.
Further description to the Attributes:
SECATTR: GW
This attribute must be set for gateway sector (HG 3570/HG 3575).
Every GW sector must be connected to a LAN sector (unlimited bandwidth).
SECATTR: LAN / WAN

This attribute describes an IP segment in the customer’s network. It has to be
set only in addition to the attributes OWN&EXCL.
The following rule must be considered:
The attribute LAN must be set, if the sector in the customer IP net is unlimited.
The attribute WAN must be set, if the sector in the customer IP net is limited.
WAN sectors are always located between LAN sectors!
HFA phones are not configured at a WAN sector. They are always assigned
to a LAN sector.
SECATTR: OWN & EXCL

The sector is managed by RM as an own (OWN) node exclusively (EXCL).
Without the attribute EXCL the RM does not seize bandwidth (for LAN) or
does not count Channels (GW).
SECATTR: HHS / AP
These attributes are to be set (either/or) only in addition to the attribute GW
and identify the shelf types that the GW situated are.
If the attribute AP is set, a sector path must be assigned to this sector (GW).
SECATTR: NODMC
This attribute blocks DMC (Direct Media Connection), if this sector is used for
a call.
A31003-H3160-S104-8-7620, 07/2014
Key Terms
Sector attribute O E A H N
 W X P H O
 N C S D
 L  M
Sector type C
GW X X A A
LAN/WAN X X O
• The unrestricted used attributes are marked with “X”.
• Attributes, which are inside of a group defined with double lines, marked with
“A” can only be used alternatively.
• Attributes, marked with “O”, can be set optionally (depending on the use
case).
The administration of the following parameters can be dispensed with depending

on application case (sector types/attributes).
BANDWI:
Bandwidth in Kbit/s (Attention: BANDWI=0 means unlimited!)
GWLAN:
Sector number of the LAN in which the gateway is connected. The used B
channels of a HG 3570/HG 3575 board can only be displayed with AMO
GKTOP, if the GWLAN number is entered.
SECPANO1:
Sector path number 1 is used for the feature HFA and IPDA. Sector -path
number 1 (SECPANO1) defines the way from the host to the remote sector,
at which HFA phones or a HG 3575 gateway is connected to.
Under this sector path number all sectors passed through to reach this sector
from a HHS are entered. The sector path number 1 begins with the sector
nearest the HHS and ends with the most remote.
All sectors, which are between the HHS and the end point, have to be entered
for this sector path.
The destination sector is not part of the sector path.
Because the RM is not released for IP trunking, the SECPANO2 and
SECPANO3 are not used.
Example for the illustration “Example of Sector/cluster definition.....”:
Sector path for cluster 1: 200&201 (not 202)
A31003-H3160-S104-8-7620, 07/2014
Configuration Rules
17.2.4.2 AMO GKTOP: Parameter in the Branch TYPE=IPDA

(only for HFA)
GWSEC
A GWSEC must only be defined, if a HG 3530 is installed in an AP-IP. In this
case the sector number of the HG 3575 must be entered.
HFASEC
For cluster with HFA phones the sector number of the LAN to which the
phones are connected is entered.
17.3 Configuration Rules

• To each HG 3570/3575 a GW sector must be assigned.
• Every GW sector must be connected to a LAN sector (BANDW=0, unlimited

bandwidth).
• A sector path has to be assigned to every endpoint. Endpoints include:
– A GW sector in the access point (HG 3575)
– A HFA sector
• The endpoint (GW sector / HFA sector) is not part of the path description.
• A cluster ID has to be assigned to all HFA subscribers.
• A cluster ID whose HFA subscribers are configured in the host system must
be assigned to a HFA sector.
• A cluster ID whose HFA subscribers are configured in the access point must
be assigned to a HFA sector and the GW sector of the access point.
17.4 Used Bandwidth

DISPLAY-SIPCO:TYPE=BANDW;
IMPORTANT: Bandwidth table must be adjust customer specific.

CHANGE-SIPCO:TYPE=BANDW,.........;
A31003-H3160-S104-8-7620, 07/2014
Configuring the Resource Management for a HFA Configuration
17.5 Configuring the Resource Management for a HFA Configuration
17.5.1 Basic Situation
HFA (G711, Packet Size=20)

HG 3500
2420
Mode:
SECTOR
CL10
HG 3530
S100 HFA (G711Pref, Packet Size=20)
2421
LAN
TDM
SECTOR
Node 10-30-200 S101
LAN
Bandwidth:
250 KBit/s
SECTOR Bandwidth:
S131 200 KBit/s
WAN SECTOR
S135
SECTOR
S132 SECTOR
S136
LAN
LAN
(G711Pref, Packet Size=20) HFA

2424
2422
CL32 CL36
(G711Pref, Packet Size=20) HFA HFA (G729, Packet Size=20)
2425 2423
Figure 19 Resource management for HFA configuration
Network plan for the Resource Management

The basic situation is as following:
A31003-H3160-S104-8-7620, 07/2014
At node 10-30-200 there is the feature HFA. This feature is already configured. It
is assumed that four (2x2) HFA subscribers lay behind a bandwidth limited WAN
routes and two HFA phones are located in the local IP network of the Host. These
routes are described for the resource management in sectors131/135 (limited
bandwidth), sectors 132/136 (HFA in the local unlimited LAN) and the sectors
100/101 (local, unlimited network at the Host).The sector 101 is only used to
describe a DMC connection between cluster 32 and 36.
Sector paths have to be defined, that a connection from sector 132N (136) to the
Host can be calculated.
The HFA subscriber are set in cluster 32 (to S132), cluster 36 (to S136) and
cluster 10 (to S100).
All HFA subscribers have the attribute “DMC allowed”:

CHANGE-SDAT:STNO=2420&&2425,TYPE=ATTRIBUT,AATTR=DMCALLWD;
The RTP-sample size has an influence on the bandwidth. All IP-phones in this
documentation are using 20ms sample size for both G711 and G.729A. This can
be configured in the database of the IP-phone or via DLS.
17.5.2 Codec Settings for the HFA Subscribers

The codec information used for a call must be available to the resource manager
in order to calculate the required bandwidth.
In the case of HFA terminals, the setting in the AMO must match the setting in
the terminal (configuration). In our example, the HFA subscribers have been
configured via DLS or the local WBM such that the HFA devices in the host prefer
G.711 and the HFA subscribers behind the WAN route force G.729A.
The sample size of the IP phones impacts the required bandwidth. A sample size
of 20ms is assumed here both for G.711 and G.729 A. These values can be
changed on the terminal (or via DLS).
CHANGE-SBCSU:STNO=2420&2421,OPT=OPTI,IPCODEC=G711P;
CHANGE-SBCSU:STNO=2422&2423,OPT=OPTI,IPCODEC=G729A;
CHANGE-SBCSU:STNO=2424&2425,OPT=OPTI,IPCODEC=G711P;
17.5.3 Sectors for the LAN/WAN

The sectors, which describe the LAN/WAN are defined first. These are the
sectors S100, S101, S131, S132, S135 and S136. The sectors S131 and S135
are WAN sectors. The bandwidth is limited to 200kBits/s and 250 kBits/s.
A31003-H3160-S104-8-7620, 07/2014
Sector 100, 101, 132 and 136:

The attributes OWN&EXCL must be entered. The sectors are LAN sectors with
unlimited bandwidth.
ADD-GKTOP:TYPE=RESMGMT1,SECNO=100,SECATTR=OWN&EXCL&LAN,PNNO=10-
30-200,BANDWI="0";
30-200,BANDWI="0";
30-200,BANDWI="0";
30-200,BANDWI="0";
Sector 131 and 135:

The attributes OWN&EXCL must be entered. The sectors are WAN sectors with
limited bandwidth.
ADD-GKTOP:TYPE=RESMGMT1,SECNO=131,SECATTR=OWN&EXCL&WAN,PNNO=10-
30-200,BANDWI="250";
30-200,BANDWI="200";
17.5.4 Allocation of the Gateways and Subscribers

Here is defined that the subscribers 2420 and 2421 are in cluster 10 and attached
to HFA LAN (sector 100).
ADD-GKTOP:TYPE=IPDA,CLUSTNO=10,HFASEC=100;
CHANGE-SDAT:STNO=2420,TYPE=DATA1,CLUSTID=10;
CHANGE-SDAT:STNO=2421,TYPE=DATA1,CLUSTID=10;;
ADD-GKTOP:TYPE=IPDA,CLUSTID=36,HFASEC=136;
ADD-GKTOP:TYPE=IPDA,CLUSTID=32,HFASEC=132;
Example for the bandwidth situation after these steps:
Call situation from 2424 to 2425 (cluster internal).

DISPLAY-GKTOP:TYPE=ALL,SCOPE=DYN;
A31003-H3160-S104-8-7620, 07/2014
---------+-------------------------------------------------------------+
SECTOR | 100 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | UNLIMITED |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 101 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 131 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 250 |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 132 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 135 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 200 |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 136 |
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+

BANDWIDTH COMPUTING TABLE : 
------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| INDEX | CODEC TYPE | FRAME SIZE | RESERVED |
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 22 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 92 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 36 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
A31003-H3160-S104-8-7620, 07/2014
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 72 |
| 13 | G723_DMC | 30 | 27 |
| 14 | G711_FS_UNKNOWN | 60 | 83 |
Interpretation:
Only bandwidth in sector 132, to which the subscribers are assigned, is reserved.
Both subscribers are using G711 with DMC (AMO SIPCO:BANDW -> Index 11).
If the value of the bandwidth of index 11 is smaller as the double value of index
1, two times of index 1 is calculated and displayed.
The bandwidth for the master connection is not reserved yet, because there are
no sector paths defined at this moment.
All bandwidths used in these examples in the AMO SIPCO do not claim to
be true. The defined values are used for demonstration purposes only!!!
The table in the AMO SIPCO must always be configured for the respective
customer.
17.5.5 Define Sector Paths

The sector paths are necessary to calculate the bandwidth in all used sectors.
In this example 2 sector paths are necessary.
Sector path 1 defines the path from the Host to the destination sector 132:
ADD-GKTOP:TYPE=SECPATH,SECPANO=1,SECDE=100&101&131;
Sector path 2 defines the path from the Host to the destination sector 136:
17.5.6 Assign the sector paths

CHANGE-GKTOP:TYPE=RESMGMT1,SECNO=132,SECPANO1=1;
Example for the bandwidth situation after these steps:

Call situation from 2424 to 2425 (cluster internal).


---------+-------------------------------------------------------------+ 
SECTOR | 100 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 178 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
A31003-H3160-S104-8-7620, 07/2014
---------+-------------------------------------------------------------+ 
SECTOR | 101 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 178 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 131 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 72 |
USED-BW | 178 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 132 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 135 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 200 |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 136 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+

------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 22 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 92 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 36 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 72 |
Interpretation:
A31003-H3160-S104-8-7620, 07/2014
The Resource Manager determines “resulting sector paths”, to reserve bandwidth

for the master connection. Therefore the sector paths of both end points are
compared. In this example the sector path of the A-party 2424 is
S100&S101&S131, destination sector S132. The sector path of the B-party 2425
is S100&S101&S131, destination sector S132. This leads to the result, that all
sectors are common sectors. Therefore the sectors S100, S101 and S131 must
be the sectors for the master connection (reserved bandwidth with two times
Index 1). The DMC connection uses the destination sector (sector S132). There
the bandwidth of 182 kBit/s (Index 11) is reserved.
Second example for the bandwidth situation after these steps:

Call situation from 2424 to 2422 (cluster to cluster).
---------+-------------------------------------------------------------+ 
SECTOR | 100 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 111 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 101 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 131 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 68 |
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 132 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 135 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 18 |
USED-BW | 182 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 136 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 182 |
R-GW-MC | 0 |
A31003-H3160-S104-8-7620, 07/2014
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
DIS-SIPCO:TYPE=BANDW;

------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 22 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 92 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 36 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 72 |
| 13 | G723_DMC | 30 | 27 |
| 14 | G711_FS_UNKNOWN | 60 | 83 |
Interpretation:
The Resource Manager determines “resulting sector paths”, to reserve bandwidth

for the master connection. Therefore the sector paths of both end points are
compared. In this example the sector path of the party A 2424 is
S100&S101&S131, destination sector S132. The sector path of the party B 2422
is S100&S101&S135, destination sector S136. This leads to the result, that
sector S101 is the last common sector. Therefore the sector S100 must be the
sector for the master connection (reserved bandwidth with one time Index 1 plus
one time Index 2). The DMC connection uses the last common sector (sector
S101). The bandwidth of 182 kBit/s (Index 11) is reserved in all affected sectors
(S101, S131, S135, S132 and S136).
A31003-H3160-S104-8-7620, 07/2014
Configuring the Resource Management for an IPDA Configuration with TDM Phones
17.6 Configuring the Resource Management for an IPDA Configuration with

TDM Phones
Node 10-30-200
SECTOR S170 HG 3500

Mode:
HG 3570
SECTOR
S100
TDM LAN
7240
(G711&G729&EC)
Bandwidth:
150 KBit/s
SECTOR
S171
WAN
SECTOR
S172
LAN
SECTOR S175 HG 3575

SECTOR S176 HG 3575
AP 17
AP 18
TDM (G711&G729OPT&EC)
7280
7282
7281
7283
Figure 20 Resource management for IPDA configuration with TDM phones
A31003-H3160-S104-8-7620, 07/2014
There is the feature IPDA at node 10-30-200. The feature is already configured
with access points 17 and 18. It is assumed, that both access points are located
behind a bandwidth limited WAN. This situation is described for the resource
management in sector S171 (bandwidth limited) and in bandwidth unlimited LAN
sectors S100 (Host) and S172 (access points). gateway sectors are necessary
for HG 3570 and HG 3575 in the IPDA feature (S170, S175 and S176). The sector
S172 is necessary, to describe the direct connection between both HG 3575
gateways. Sector paths must be defined for the HG 3575 gateways, to describe
their location to the Host correctly.
The Frame Size for G711 is set to 20 ms for all HG 3570/75:

CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=61,TYPE=ASC,PRIO=PRIO2,CODEC=G711A,RTP
=20;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO1,CODEC=G711A,RTP=20;
CHANGE-
The Codec G729 should be used for a call between a Host terminal and an AP
terminal. The Codec G711 should be used for a call between an AP terminal of
access point 17 and an AP terminal in access point 18.
CHANGE-SDAT:STNO=7240,TYPE=DATA1,CLASSMRK=G711&G729A&EC;
CHANGE-
SDAT:STNO=7280&&7282,TYPE=DATA1,CLASSMRK=G711&G729AOPT&EC;

sectors S100, S171 and S172. The sector 171 ist a WAN sector. The bandwidth
is limited to 150 kBit/s.
Sector 100 and 172:

30-200,BANDWI="0";
30-200,BANDWI="0";
Sector 171:
The attributes OWN&EXCL must be entered. The sector is a WAN sector with
limited bandwidth.
30-200,BANDWI="150";
A31003-H3160-S104-8-7620, 07/2014
17.6.3 Sectors for the Gateways

The sectors S170, S175 and S176 are defined.
The sector 170 has the attributes OWN&EXCL (see before) and HHS (is located
in the Host) and GW (is a gateway).
ADD-
GKTOP:TYPE=RESMGMT1,SECNO=170,SECATTR=OWN&EXCL&HHS&GW,PNNO=10-
30-200,GWLAN=100;
The sectors 175 and 176 have the attributes OWN&EXCL (see before) and AP
(are located in an access point) and GW (are gateways).
ADD-
GKTOP:TYPE=RESMGMT1,SECNO=175,SECATTR=OWN&EXCL&AP&GW,PNNO=10-30-
200,GWLAN=172;
ADD-
200,GWLAN=172;
17.6.4 Allocation of the Gateways to their Sectors

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=61,TYPE=GWSECTOR,GWSECTNO=170;
CHANGE-STMIB:MTYPE=NCUI2,LTU=17,TYPE=GWSECTOR,GWSECTNO=175;

In this example only one sector path is necessary, because access point 17 and
18 are reached via the same path from the Host.
17.6.6 Assign the Sector Path

1st example for bandwidth reservation after these steps:
Call situation from 7280 to 7282 (GW SECTOR 175 to GW SECTOR 176).

---------+----------------------------------------------------------------+ 
SECTOR | 100 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
A31003-H3160-S104-8-7620, 07/2014
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 170 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 60 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 171 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 150 |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 172 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 184 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 175 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 59 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 176 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 59 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
DIS-SIPCO:TYPE=BANDW;

------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 22 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 184 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 36 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 72 |
| 13 | G723_DMC | 30 | 27 |
| 14 | G711_FS_UNKNOWN | 60 | 83 |
A31003-H3160-S104-8-7620, 07/2014
Interpretation:
Only bandwidth in sector (172), which connect the two GW sectors of AP17 and
AP18, is reserved. Both subscribers use G711 with 20ms frame size (AMO
SIPCO:BANDW -> Index 5).
You can see, that only 59 B-channels are available in the GW sectors 175 and
176.
2nd example for bandwidth reservation after these steps:

Call situation from 7282 to 7240 (GW SECTOR 175 to GW SECTOR 170).

---------+----------------------------------------------------------------+ 
SECTOR | 100 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 72 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 170 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 59 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 171 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 78 |
USED-BW | 72 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 172 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 72 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 175 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 60 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 176 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 59 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
A31003-H3160-S104-8-7620, 07/2014

------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 22 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 184 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 72 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 72 |
| 13 | G723_DMC | 30 | 27 |
| 14 | G711_FS_UNKNOWN | 60 | 83 |
Interpretation:
Bandwidth in all used sectors (172&171&100), which connect AP18 to the Host,
is reserved. The Codec G729A with 20ms Frame size is used for this call (AMO
SIPCO:BANDW -> Index 8).
You can see, that only 59 B-channels are available in the GW sectors 170 and
176.
A31003-H3160-S104-8-7620, 07/2014
Configuring the Resource Management for an IPDA Configuration with TDM Phones and HFA in Access Point
17.7 Configuring the Resource Management for an IPDA Configuration with

TDM Phones and HFA in Access Point
Node 10-30-200
SECTOR S170 HG 3500

Mode: HG
3570
SECTOR
S100
TDM LAN
7240
(G711&G729&EC)
Bandwidth:
150 KBit/s
WAN SECTOR
S171
SECTOR LAN
S172
HG 3575 SECTOR S176

SECTOR S175 HG 3575
HG 3500
AP 17 Mode:
HG 3530 AP 18
Bandwidth: SECTOR
7280 200 KBit/s S180
TDM (G711&G729OPT&EC) WAN TDM (G711&G729OPT&EC)

7282
SECTOR
S181
2420
LAN
CL81
2421
Figure 21 Resource management for IPDA configuration with TDM phones

and HFA inaccess point
A31003-H3160-S104-8-7620, 07/2014
There is the feature IPDA at node 10-30-200. The feature is already configured
with access points 17 and 18. The feature HFA is configured in AP18. It is
assumed, that both access points are located behind a bandwidth limited WAN.
This situation is described for the resource management in sector S171
(bandwidth limited) and in bandwidth unlimited LAN sectors S100 (Host) and
S172 (access points). gateway sectors are necessary for HG 3570 and HG 3575
in the IPDA feature (S170, S175 and S176). The sector S172 is necessary, to
describe the direct connection between both HG 3575 gateways. Sector paths
must be defined for the HG 3575 gateways, to describe their location to the Host
correctly.
The WAN for HFA is connected to the location of the displaced shelf. This
situation is described for the resource management in the way, that the WAN
sector 180 borders on the sector 172 and from the other side on sector 181 to
which the HFA cluster 81 is connected.
The frame size for G711 is set to 20 ms for all HG 3570/75:

CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=61,TYPE=ASC,PRIO=PRIO2,CODEC=G711A,
RTP=20;
CHANGE-
CHANGE-
The codec G729 should be used for a call between a Host terminal and an AP
terminal. The Codec G711 should be used for a call between an AP terminal of
access point 17 and an AP terminal in access point 18.
CHANGE-SDAT:STNO=7240,TYPE=DATA1,CLASSMRK=G711&G729A&EC;
CHANGE-
All HFA subscribers have the attribute “DMC allowed”.
CHANGE-SDAT:STNO=2420&&2421,TYPE=ATTRIBUT,AATTR=DMCALLWD;
The IPDA gateways should support DMC.
• HG 3570:
CHANGE-SIPCO:TYPE=DMCDATA,DMCALLWD=YES;
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=61,TYPE=DMCDATA,DMCCONN=45;
• HG 3575:
CHANGE-STMIB:MTYPE=NCUI2,LTU=17,TYPE=DMCDATA,DMCALLWD=YES,
DMCCONN=45;
CHANGE-STMIB:MTYPE=NCUI2,LTU=18,TYP=DMCDATA,DMCALLWD=YES,
DMCCONN=45;
A31003-H3160-S104-8-7620, 07/2014
Settings of the Codec list for the gateways (for DMC connections).
CHANGE-
=20;
CHANGE-
=20;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=17,TYPE=ASC,PRIO=PRIO1,CODEC=G711,RTP=20;
CHANGE-
CHANGE-
STMIB:MTYPE=NCUI2,LTU=18,TYPE=ASC,PRIO=PRIO1,CODEC=G711,RTP=20;
CHANGE-
17.7.2 Settings for the HFA Subscribers

The Codec information, which will be used for a call, must be available for the
Resource Manager for reserving the necessary bandwidth.
The setting in the AMO must be corresponding to the setting at the terminal
(Administration) for the HFA subscriber.
CHANGE-SBCSU:STNO=2420&2421,OPT=OPTI,IPCODEC=G729A;
Codec setting of the HFA subscribers for the master connection in the IPDA
section.
CHANGE-

sectors S100, S171 and S172. The sector 171 ist a WAN sector. The bandwidth
is limited to 150 kBit/s.
Sector 100 and 172:

30-200,BANDWI="0";
30-200,BANDWI="0";
A31003-H3160-S104-8-7620, 07/2014
Sector 171:
limited bandwidth.
30-200,BANDWI="150";
Sector 181:
The sectors 181 (LAN) and 181 (WAN) are necessary for the HFA configuration.
The attributes OWN&EXCL must be entered. The sector is a LAN sector with
30-200,BANDWI="0";
SECTOR 180:
limited bandwidth.
30-200,BANDWI="200";
17.7.4 Sectors for the Gateways

The sectors S170, S175 and S176 are defined.
The sector 170 has the attributes OWN&EXCL (see before) and HHS (is located
in the Host) and GW (is a gateway).
ADD-
GKTOP:TYPE=RESMGMT1,SECNO=170,SECATTR=OWN&EXCL&HHS&GW,PNNO=10-
30-200,GWLAN=100;
The sectors 175 and 176 have the attributes OWN&EXCL (see before) and AP
(are located in an access point) and GW (are gateways).
ADD-
200,GWLAN=172;
ADD-
200,GWLAN=172;
17.7.5 Assignment of the HFA Subscribers to the

Sectors
The subscribers 2420 and 2421 are configured in cluster 81 and are connected
to the HFA LAN sector 181. Because they are subscribers of the AP18
additionally, it is necessary to add the GW sector of their HG 3575 in the
parameter GWSEC (S176).
A31003-H3160-S104-8-7620, 07/2014
ADD-GKTOP:TYPE=IPDA,CLUSTID=81,HFASEC=181,GWSEC=176;
CHANGE-SDAT:STNO=2420,TYP=DATA1,CLUSTID=81;
CHANGE-SDAT:STNO=2421,TYP=DATA1,CLUSTID=81;
17.7.6 Allocation of the Gateways to their Sectors

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=61,TYPE=GWSECTOR,GWSECTNO=170;

In this example only one sector path is necessary, because access point 17 and
18 are reached via the same path from the host.
An own sector path from the host to the destination sector 181 of the HFA
subscribers in cluster 81 must be defined.
ADD-GKTOP:TYPE=SECPATH,SECPANO=2,SECDE=100&171&172&180;
17.7.8 Assign the Sector Path

Example for bandwidth reservation after these steps:
Call situation from 2420 to 7280 (SECTOR 181 to GW SECTOR 175).


---------+----------------------------------------------------------------+ 
SECTOR | 100 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 170 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 60 |
R-GW-DMC | 45 |
---------+-------------------------------------------------------------+ 
SECTOR | 171 | 
A31003-H3160-S104-8-7620, 07/2014
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 150 |
USED-BW | 0 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 172 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 220 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+ 
SECTOR | 175 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 58 |
R-GW-DMC | 44 |
---------+-------------------------------------------------------------+ 
SECTOR | 176 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 0 |
R-GW-MC | 59 |
R-GW-DMC | 45 |
---------+-------------------------------------------------------------+
SECTOR | 180 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
S-BW | 122 |
USED-BW | 78 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+
SECTOR | 181 | 
---------+-------------------------------------------------------------+
PNNO | 10- 30-200 |
---------+-------------------------------------------------------------+
USED-BW | 78 |
R-GW-MC | 0 |
R-GW-DMC | 0 |
---------+-------------------------------------------------------------+

------------------------------------------------------------------
+-------+----------------------+-----------------+---------------+
| | | (MS) | BANDW.(KBIT) |
+-------+----------------------+-----------------+---------------+
| 1 | G711_HFA | 30 | 89 |
| 2 | G729_HFA | 40 | 36 |
| 3 | G723_HFA | 30 | 25 |
| 4 | G711_F10_IPDA | 10 | 120 |
| 5 | G711_F20_IPDA | 20 | 184 |
| 6 | G711_F30_IPDA | 30 | 83 |
| 7 | G711_F60_IPDA | 60 | 74 |
| 8 | G729_F20_IPDA | 20 | 36 |
| 9 | G729_F40_IPDA | 40 | 22 |
| 10 | G729_F60_IPDA | 60 | 18 |
| 11 | G711_DMC | 30 | 182 |
| 12 | G729_DMC | 40 | 78 |
A31003-H3160-S104-8-7620, 07/2014
Notes and Restrictions
| 13 | G723_DMC | 30 | 27 |
| 14 | G711_FS_UNKNOWN | 60 | 83 |
Interpretation:
The bandwidth in the sectors for HFA (S180 and S181) is reserved. There the
bandwidth using Index 12 is reserved for the compressed DMC connection,
because the flat rate value in Index 12 is greater than the double value of Index 2.
The master connection between the two access points with G711 (Index 5) will be
added with the bandwidth of the master connection of the HFA subscribers to the
HG 3530 (G729, Index 2) in sector 172.
The master connection is only active in the GW sector 176, i.e. only one master
channel is used (59 available). The master connection and one DMC connection
is active in the sector 175, i.e. 2 DSP channels are used. One of them is used the
master connection and the other for the DMC connection (58/44 available).
17.8 Notes and Restrictions

Comments on RM:
• RESMAN should never contain a route with more than 16 sectors.
• Only WAN sectors are supported for bandwidth calculation and not LAN
sectors.
• Each RESMGMT1 from AMO GKTOP must contain the AMO ZAND PKNNO
under the PKNNO parameter, i.e. this is not the AMO KNDEF entry.
• IP TRUNKING is not supported.
• Network-wide configuration is extremely time intensive and if an incorrect

sector is received from a partner system DMC is not switched (see
MSC15245 for an alternative simpler configuration).
• When a DMC connection is made the bandwidth is not reduced if the CODEC
is of a lower quality until the call is disconnected. If the bandwidth is more i.e.
a higher bandwidth is used for the DMC connection the value is increased
normally.
• MOBHFA is supported. Upon successful logon the cluster ID of the guest

station is also stored. Bandwidth calculation will take into account the path
from the guest station to the home gateway and then from the home gateway
to the called party. DMC can also increase the bandwidth dependant on which
CODEC is used for the master connection.
• The bandwidth is always calculated as configured i.e. from host system in

direction of the AP. If the call is between two APs the routes are overlaid
(compared) to establish the true route.
A31003-H3160-S104-8-7620, 07/2014
Diagnostics
• AMO SBCSU parameter IPCODEC must be configured for HFA phones to

calculate the bandwidth correctly.
• When using AMO KCSU no bandwidth reservation will be made during

ringing state (first by connect).
• Each gateway should be connected to a LAN sector (not directly to WAN!).
17.9 Diagnostics
Checking of the used bandwidth of all sectors:
DISPLAY-GKTOP:TYPE=RESMGMT1,SCOPE=DYN;
When it is required to check the implementation of the resource management, it
is sufficient at first to establish speech connections over all configured paths.
Then when the permitted bandwidth in a sector is exceeded, a path occupancy
should be obtained.
No bandwidth available
When Resource Manager is configured sometimes connections will be blocked if

no resources are free. In such a case an F4436 advisory message is signalled.
Usually the reason for the error message is a correct one and defined by
configuration i.e. more connections are attempting to use a path than are allowed
in the AMO GKTOP configuration or that a DMC connection was restricted via the
AMO GKTOP attribute NODMC. In some rarer cases, the advisory is signalled
due to hanging bandwidth, meaning a DIS-GKTOP will show bandwidth is used
even though no connections are active over the specific path. Hanging bandwidth
can be verified by executing a DIS-GKTOP in a low period of traffic.
The F4436 error message contains important information regarding exactly which
route is not available.
A31003-H3160-S104-8-7620, 07/2014
gateways_18_cli_hg3500v4.fm
Command Line Interface CLI in HG 3500
General Information
18 Command Line Interface CLI in HG 3500
18.1 General Information

The common gateway supports a Command Line Interface (CLI) for installation
and basic configuration, e.g. IP infra structure. In V.24 CLI it is possible to change
security relevant data (e.g. SSL Configuration), because the V.24 is considered
to be secure. Additionally the CLI allows the monitoring of important counters and
statistics.
The CLI can be accessed via V.24. The CLI can not be accessed via Telnet
because it is an unsecure protocol.
To get an overview of the commands type in the command help and you get an
alphabetic list of all commands.
Please refer to Section 14.10, “TYPE SERVIF - Changing the Login and
Password for the Service Access” on how to configure the access data for CLI.
The basic function of the CLI are described below. In the following sections the
CLI commands are divided into seven categories:
• General Operations
• Access control
• Gateway Setup
• Image/File Handling
• Maintenance
• SSL for WBM
• DLS
18.2 General Operations

When starting a session the administrator is asked for authentication. That is
done by entering the admin name and the password.
• To leave the session use the

logout
command.
• The list of all supported commands except the hidden commands can be
obtained with:
help
A31003-H3160-S104-8-7620, 07/2014
Access control
18.3 Access control

• The configuration write access has to be acquired before a store, upload or
download command can be done. Because of the implemented “soft lock“
handling, at first a check if somebody else has set the write access is
required.
who has write access
get write access
release write access
18.4 Gateway Setup

To permit system initialisation and basic management configuration activities
following commands are needed.
• Setting and changing the gateway name:

set hostname <hostname>
• Setting and changing the IP-Address for the ethernet port:
set ip address <ip address>
set ip subnet <ip subnet mask>
A set or a change of the IP-address or IP subnet for the ethernet port will
probably require a gateway reboot to become effective.
• Setting and changing the IP-address of the default gateway from static routes
table:
set default gateway <ip address>
• Display/change choosen identifier:
get id <parameter name>
set id <parameter name>
hostname
The parameter hostname > terms an arbitrary name for the gateway and it must
be a string of characters (e.g. set hostname Gateway1). It corresponds with the
boot line parameter "targetname".
ip address
The parameter <ip address> is a string in the form of x.x.x.x and x is an integer
(e.g. 1.2.3.4)
A31003-H3160-S104-8-7620, 07/2014
Image/File Handling
ip subnet mask
The parameter <ip subnet mask> is a string in the form of x.x.x.x and x is an
integer between 0 and 255 (e.g. 255.255.255.224).
18.5 Image/File Handling

In common gateway software configuration and distribution as well as upload and
download of configuration data via CLI is not required because it is done via
WBM.
Additionally operations for analysing event and trace data are supported.
The trace /event logs are available as:

/trace/trace.txt
/trace/trace.bak
/evtlog/evtlog.txt
/evtlog/evtlog.bak
18.6 Maintenance
The maintenance commands permit the current operational status of the gateway
to be inspected, and provides access to diagnostic tools and interface and
gateway controls.
Display
• Commands which provide information on the gateway’s software

configuration:
show version
show uptime
• Display of IP-address, subnet and gateway:
show all parameters
• Display of hostnames and IP-addresses:
show host
• Get the name of the gateway:
show hostname
• Display of arp-cache:
show arp cache
It is also stored in the bootline as targetname.
A31003-H3160-S104-8-7620, 07/2014
Maintenance
• Display of the IP address and subnetmask for the ethernet port:

show ip address
show ip subnet
• Showing the time will display the time and the date:
show time
• Command to get the IP address of the default gateway from the static routes
table:
show default gateway
• Command to display the static routes entries:
show routes
• To display the statistics of the interface table:
show if counters
• To list all existing interfaces:
show interfaces
• To get admin and operating states:
show if states
Ping and tracert
• Diagnosis Commands:
ping <ip address>
Target shell
• vxWorks shell logon/logout:

shell
exit
Gateway Reboot
From the administrator point of view two different ways of a reboot command are
of interest. At first there is the need to reboot the gateway with the current
configuration. On the other side there could be the need to support a
configuration data exchange, i.e. to take a configuration data file from extern or to
skip the latest configuration data storage and take the next older one.
It is in the responsibility of the administrator to coordinate a gateway reboot!
A31003-H3160-S104-8-7620, 07/2014
SSL for WBM
• Normal reboot of the gateway, using the current configuration data:

reset
• Reset any configuration data to factory defaults and reboot:
reset factory
• Special reboot of the gateway using an existing self-extracting image in order
to complete a software download:
activate software
18.7 SSL for WBM

SSL for WBM (i.e. https) is enabled in the factory delivered status. It cannot be
disabled.
To permit a basic configuration of SSL following commands are needed.
• Display the fingerprint of the currently active certificate for WBM access via
https.
show fingerprint
Before accepting a certificate warning in the browser, it is strongly
recommended that the administrator should compare the fingerprint of the
certificate displayed in the browser against the fingerprint shown in CLI. The
certificate must be accepted only, if both fingerprints are identical!
18.8 DLS
• Set the IP address of the DLS server
set dls ip_address <ip address[:port]>
You can set the IP address of the DLS server manually with set dls
ip_address (optional). The IP address is automatically set if you use the
function IP Devices > IP Device Interaction > Scan IP Devices (activate the
checkbox Send DLS Address in the "Configuration" tab for this).
• Show the IP address of the DLS server

show dls ip_address
The gateway contains a DLS client. This setting makes sure that the gateway
automatically recognizes the IP address of the DLS client.
• DLS PIN
IP Devices > IP Device Management > IP Device Configuration > "DLS
Connectivity"
A31003-H3160-S104-8-7620, 07/2014
DLS
Three security settings are available under PIN Mode for creating a virtual
device in the DLS:
– No PIN,
– Default PIN,
– Individual PIN.
See also Chapter 11, “DLS Client Bootstrapping”.
If you set dls pin_required to TRUE in the gateway, the gateway declines a
connection if No PIN is set in the DLS. This setting offers added security.
The PIN is automatically generated by the DLS and displayed in the Default
PIN: field in the DLS under Administration > Workpoint Interface
Configuration > "Secure mode" tab. It has the same function as a
password.
set dls pin_required <value>
Possible values: 0, 1
show dls pin_required
Possible values: FALSE, TRUE
• Activate the DLS PIN

activate dls pin <pin>
If you select Default PIN or Individual PIN as the PIN mode in the DLS, you
must use this command to enter the PIN displayed in the DLS.
• Bootstrapping
The command reset dls bootstrapping resets the gateway defaults for
DLS client bootstrapping; you can then repeat bootstrapping (see also
Chapter 11, “DLS Client Bootstrapping”).
reset dls bootstrapping
• DLS client status
Shows the value "secure" or "insecure". This is followed by a number in
brackets which is used for diagnostic purposes.
show dls_client_state
Possible values: secure, insecure
• Contact the DLS server

contact dls
This command tries to contact the DLS server.
You only need to do this to start DLS client bootstrapping after manually
configuring the DLS server’s IP address with set dls ip_address.
A31003-H3160-S104-8-7620, 07/2014
Changing the Login and Password for WBM/CLI
Otherwise, you can use contact dls to test if communication is possible

between the gateway and DLS server. An appropriate message appears.
A PIN is not needed. "No PIN" is set as the PIN mode in the DLS.
A PIN is needed. "Default PIN" or "Individual PIN" is set as the PIN mode in
the DLS.
FALSE
A PIN is not needed. "No PIN" is set as the PIN mode in the DLS.
TRUE
A PIN is needed. "Default PIN" or "Individual PIN" is set as the PIN mode in
the DLS.
secure
DLS client bootstrapping has already taken place.
insecure
DLS client bootstrapping has not yet been performed or was unsuccessful.
18.9 Changing the Login and Password for WBM/CLI

For CLI login, the same accounts as for WBM login have to be used. The
accounts can be set up and changed via AMO CGWB. The parameter ROLE
defines the access rights.
IMPORTANT: Two-stage CLI is not suppoorted.
CHANGE-
STMIB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=WBMDATA,LOGINWBM=<use
r login for wbm connection>,PASSWWBM=<password for wbm
connection>,ROLE=<role of the wbm user>;
The initial login as engr is
username: HP4K-DEVEL
Passowrd: 4K-admin
After successful login the following message appears:
Welcome to the HG 3575 <LW-version> Command Line Interpreter.
vxTarget>
A31003-H3160-S104-8-7620, 07/2014
Changing the Login and Password for WBM/CLI
<LW-version>
A31003-H3160-S104-8-7620, 07/2014
Command Line Interface CLI at HG 3575 V4
19 Command Line Interface CLI at HG 3575 V4

Please refer to IP Distributed Architecture (IPDA) , Chapter 4, “Local Access
Point Administration at CLI via Terminal”.
A31003-H3160-S104-8-7620, 07/2014
Command Line Interface CLI at HG 3575 V4
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
SNMP Support HG 3500 / HG 3575
20 SNMP Support HG 3500 / HG 3575

The HG 3500 / HG 3575 module supports the request of data via SNMP.The
standards MIB (MIB-2) and two Private Enterprises MIB-s for company specific
gateway data are supported:
MIB-2:
– (1) System Group (RFC1213)
– (2) Interfaces Group (RFC2233)
– (3) AT Group (RFC1213)
– (4) IP Group (RFC2011/RFC1213)
– (5) ICMP Group (RFC2011)
– (6) TCP Group (RFC2012)
– (7) UDP Group (RFC2013)
– (8) EGP Group (RFC1213)
– (10) Transmission Group (RFC2127)
– (11) SNMP Group (RFC1213)
– (16) RMON Group (RFC1757)
– (30) ianaifType (IANA)
– (31) ifMIB Group (RFC2233)
SNI specific (hg3550) MIB:
– (1) Error Sig Group
– (2) Control Group
– (3) Monitoring Group
– (4) Statistics Group
– (5) Send Alarm with Values (traps)
– (6) File Overflow (traps)
– (7) All Serve Group
– (8) Ethernet Statistics Group
– (9) QOS Statistics Group
– (10) B-Channel Statistics Group
– (11) Notification Group (traps)
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
– (12) IP Phone Group
– (13) RG2500 MIB (platform, management, global data, traps, ...)
Company specific (hg3550 v11) MIB:
– (2) I&C Admin MIB (systemOID)
Notes
To make the MIB-s known to a MIB browser, the following files are required:
MIB-2 parts:
• mib-2.my: standard MIB-II (1.3.6.1.2.1.1-11)
• iana.my: IANAifType (1.3.6.1.2.1.30)
• my_rmon2.my: RMON MIB (1.3.6.1.2.1.16.19)
• rfc2127.my: ISDN-MIB (1.3.6.1.2.1.10.20)
• rfc2233.my: IF-MIB (1.3.6.1.2.1.2 and 1.3.6.1.2.1.31)
SNI specific (hg3550) MIB parts:
• hg1500.my: HG3550 MIB (1.3.6.1.4.1.231.7.2.7.1-12)
• ar2500_platform.my: Platform MIB (1.3.6.1.4.1.231.7.2.7.13.1)
• ar2500_management.my: Management MIB (1.3.6.1.4.1.231.7.2.7.13.2)
• cg2500.my: CG2500 MIB (1.3.6.1.4.1.231.7.2.7.13.3)
Company specific (hg3550 v11) MIB parts:
• hg3550_v11.my: system OID for hg3550 V2 (1.3.6.1.4.1.4329.2.24)
These files are part of each official production, packed in a zip file.
The SNMP MIBs can be downloaded via the SNMP Configurator, tab SNMP
Control of the HiPath 4000 Assistant (Diagnostics > Faul Management) or via
sftp from the directory /opt/ncc/mib.
For all information on Object Identifiers (OID) please refer to https://wpb.global-

intra.net/comwiki/bin/view.pl/Standardization/OIDs.
e/Information_Pool/Interfaces_and_Protocols/Chapters/Chapter8.aspx.
You can find more informationen on the SNMP Configurator in the online help or
in the HiPath 4000 Assistant documentation for Simple Network Management
Protocol (http://apps.g-dms.com:8081/techdoc/en/P31003H3460M1410176A9/
inde.htm).
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
Some MIB objects and MIB files have old, historical names. These MIB objects
and MIB files have been created earlier, for previous products (CG2500, AR2500,
HG1500 etc.). These objects and files could been inherited for the new products
with minor (or without any) changes, thus the old, unchanged object and file
names are continuously used in the new products (HG 3500, HG 3575) too.
The following tables describe the details of the supported objects, sorted by
object ID. The last table contains a repeated and collected list of the SNMP traps
in the MIB object tree.
The SNMP traps are marked by “TRAP” in the Syntax column. They are collected
and repeated in the last table.
The Access column contains shortcuts of the object data access possibilities:
• RO: Read-Only
• RW: Read-Write
• RC: Read-Create
If no Access shortcut is present, then the object is not a data container object,
thus it is not directly accessible.
The texts in the Description column are generally extracted from the MIB source
files, thus they may contain references to old, historical product names. These
are valid for the current products too.
For more information see the referenced MIB files.
Object-ID Object name Syntax Access Description

1.3.6.1.2.1.1 system System MIB, see mib-2.my
1.3.6.1.2.1.1.1 sysDescr DisplayString RO Textual description of the system,
(SIZE (0..255)) including the full name and version
identification of the system's hardware
type, software operating-system, and
networking software
1.3.6.1.2.1.1.2 sysObjectID OBJECT RO The vendor's authoritative identification
IDENTIFIER of the network management subsystem
contained in the entity
1.3.6.1.2.1.1.3 sysUpTime TimeTicks RO The time (in hundredths of a second)
since the network management portion
of the system was last re-initialized
1.3.6.1.2.1.1.4 sysContact DisplayString RW The textual identification of the contact
(SIZE (0..255)) person for this managed node, together
with information on how to contact this
person
1.3.6.1.2.1.1.5 sysName DisplayString RW An administratively-assigned name for
(SIZE (0..255)) this managed node. By convention, this
is the node's fully-qualified domain name
Table 14 Data in the standard MIB-2
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.1.6 sysLocation DisplayString RW The physical location of this node
(SIZE (0..255))
1.3.6.1.2.1.1.7 sysServices INTEGER RO A value which indicates the set of
(0..127) services that this entity primarily offers
1.3.6.1.2.1.2 interfaces Interfaces MIB, see mib-2.my and

rfc2233.my
1.3.6.1.2.1.2.1 ifNumber INTEGER RO The number of network interfaces
(regardless of their current state) present
on this system.
1.3.6.1.2.1.2.2 ifTable SEQUENCE A list of interface entries. The number of
OF IfEntry entries is given by the value of ifNumber.
1.3.6.1.2.1.2.2.1 ifEntry IfEntry An entry containing management
information applicable to a particular
interface.
1.3.6.1.2.1.2.2.1.1 ifIndex INTEGER RO A unique value, greater than zero, for
each interface.
1.3.6.1.2.1.2.2.1.2 ifDescr DisplayString RO A textual string containing information
(SIZE (0..255)) about the interface.
1.3.6.1.2.1.2.2.1.3 ifType INTEGER RO The type of interface.
1.3.6.1.2.1.2.2.1.4 ifMtu INTEGER RO The size of the largest packet which can
be sent/received on the interface,
specified in octets.
1.3.6.1.2.1.2.2.1.5 ifSpeed Gauge RO An estimate of the interface's current
bandwidth in bits per second.
1.3.6.1.2.1.2.2.1.6 ifPhysAddress PhyCountersA RO The interface's address at its protocol
ddress sub-layer.
1.3.6.1.2.1.2.2.1.7 ifAdminStatus INTEGER RW The desired state of the interface.
- up(1) ready to pass packets
- down(2)
- testing(3) in some test mode
1.3.6.1.2.1.2.2.1.8 ifOperStatus INTEGER RO The current operational state of the
interface.
- up(1) ready to pass packets
- down(2)
- testing(3) in some test mode
- unknown(4) status can not be
determined for some reason.
- dormant(5)
- notPresent(6) some component is
missing
- lowerLayerDown(7) down due to state
of lower-layer interface(s)
1.3.6.1.2.1.2.2.1.9 ifLastChange TimeTicks RO The value of sysUpTime at the time the
interface entered its current operational
state.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.2.2.1.10 ifInOctets Counter RO The total number of octets received on
the interface, including framing
characters.
1.3.6.1.2.1.2.2.1.11 ifInUcastPkts Counter RO The number of packets, delivered by this
sub-layer to a higher (sub-)layer, which
were not addressed to a multicast or
broadcast address at this sub-layer.
1.3.6.1.2.1.2.2.1.12 ifInNUcastPkts Counter RO The number of packets, delivered by this
were addressed to a multicast or
deprecated
1.3.6.1.2.1.2.2.1.13 ifInDiscards Counter RO The number of inbound packets which
were chosen to be discarded even
though no errors had been detected to
prevent their being deliverable to a
higher-layer protocol.
1.3.6.1.2.1.2.2.1.14 ifInErrors Counter RO For packet-oriented interfaces, the
number of inbound packets that
contained errors preventing them from
being deliverable to a higher-layer
protocol.
1.3.6.1.2.1.2.2.1.15 ifInUnknownProtos Counter RO For packet-oriented interfaces, the
number of packets received via the
interface which were discarded because
of an unknown or unsupported protocol.
1.3.6.1.2.1.2.2.1.16 ifOutOctets Counter RO The total number of octets transmitted
out of the interface, including framing
characters.
1.3.6.1.2.1.2.2.1.17 ifOutUcastPkts Counter RO The total number of packets that higher-
level protocols requested be transmitted,
and which were not addressed to a
multicast or broadcast address at this
sub-layer, including those that were
discarded or not sent.
1.3.6.1.2.1.2.2.1.18 ifOutNUcastPkts Counter RO The total number of packets that higher-
and which were addressed to a multicast
or broadcast address at this sub-layer,
including those that were discarded or
not sent.
deprecated
1.3.6.1.2.1.2.2.1.19 ifOutDiscards Counter RO The number of outbound packets which
though no errors had been detected to
prevent their being transmitted.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.2.2.1.20 ifOutErrors Counter RO For packet-oriented interfaces, the
number of outbound packets that could
not be transmitted because of errors. For
character-oriented or fixed-length
interfaces, the number of outbound
transmission units that could not be
transmitted because of errors.
1.3.6.1.2.1.2.2.1.21 ifOutQLen Gauge RO The length of the output packet queue (in
packets).
1.3.6.1.2.1.2.2.1.22 ifSpecific OBJECT RO A reference to MIB definitions specific to
IDENTIFIER the particular media being used to realize
the interface.
deprecated
1.3.6.1.2.1.3 at Address Translation MIB, see mib-2.my

Note: This group is deprecated by MIB-II.
That is, it is being included solely for
compatibility with MIB-I nodes, and will
most likely be excluded from MIB-III
nodes
1.3.6.1.2.1.3.1 atTable SEQUENCE The MIB module to describe generic

OF AtEntry objects for network interface sub-layers.
This MIB is an updated version of MIB-
II's ifTable, and incorporates the
extensions defined in RFC 1229.
1.3.6.1.2.1.3.1.1 atEntry AtEntry Each entry contains one
NetworkAddress to `physical' address
equivalence
1.3.6.1.2.1.3.1.1.1 atIfIndex INTEGER RW The interface on which this entry's
equivalence is effective
1.3.6.1.2.1.3.1.1.2 atPhysAddress PhysAddress RW The media-dependent `physical' address
1.3.6.1.2.1.3.1.1.3 atNetAddress NetworkAddre RW The NetworkAddress (e.g., the IP
ss address) corresponding to the media-
dependent `physical' address
1.3.6.1.2.1.4 ip IP MIB, see mib-2.my

1.3.6.1.2.1.4.1 ipForwarding INTEGER RW The indication of whether this entity is
acting as an IP gateway in respect to the
forwarding of datagrams received by, but
not addressed to, this entity
forwarding(1): acting as a gateway
not-forwarding(2): NOT acting as a
gateway
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.4.2 ipDefaultTTL INTEGER RW The default value inserted into the Time-
To-Live field of the IP header of
datagrams originated at this entity,
whenever a TTL value is not supplied by
the transport layer protocol
1.3.6.1.2.1.4.3 ipInReceives Counter RO The total number of input datagrams
received from interfaces, including those
received in error
1.3.6.1.2.1.4.4 ipInHdrErrors Counter RO The number of input datagrams
discarded due to errors in their IP
headers, including bad checksums,
version number mismatch, other format
errors, time-to-live exceeded, errors
discovered in processing their IP options,
etc.
1.3.6.1.2.1.4.5 ipInAddrErrors Counter RO The number of input datagrams
discarded because the IP address in
their IP header's destination field was not
a valid address to be received at this
entity
1.3.6.1.2.1.4.6 ipForwDatagrams Counter RO The number of input datagrams for which
this entity was not their final IP
destination, as a result of which an
attempt was made to find a route to
forward them to that final destination
1.3.6.1.2.1.4.7 ipInUnknownProtos Counter RO The number of locally-addressed
datagrams received successfully but
discarded because of an unknown or
unsupported protocol
1.3.6.1.2.1.4.8 ipInDiscards Counter RO The number of input IP datagrams for
which no problems were encountered to
prevent their continued processing, but
which were discarded (e.g., for lack of
buffer space)
1.3.6.1.2.1.4.9 ipInDelivers Counter RO The total number of input datagrams
successfully delivered to IP user-
protocols (including ICMP)
1.3.6.1.2.1.4.10 ipOutRequests Counter RO The total number of IP datagrams which
local IP user-protocols (including ICMP)
supplied to IP in requests for
transmission
1.3.6.1.2.1.4.11 ipOutDiscards Counter RO The number of output IP datagrams for
which no problem was encountered to
prevent their transmission to their
destination, but which were discarded
(e.g., for lack of buffer space)
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.4.12 ipOutNoRoutes Counter RO The number of IP datagrams discarded
because no route could be found to
transmit them to their destination
1.3.6.1.2.1.4.13 ipReasmTimeout INTEGER RO The maximum number of seconds which
received fragments are held while they
are awaiting reassembly at this entity
1.3.6.1.2.1.4.14 ipReasmReqds Counter RO The number of IP fragments received
which needed to be reassembled at this
entity
1.3.6.1.2.1.4.15 ipReasmOKs Counter RO The number of IP datagrams
successfully re-assembled
1.3.6.1.2.1.4.16 ipReasmFails Counter RO The number of failures detected by the IP
re-assembly algorithm (for whatever
reason: timed out, errors, etc)
1.3.6.1.2.1.4.17 ipFragOKs Counter RO The number of IP datagrams that have
been successfully fragmented at this
entity
1.3.6.1.2.1.4.18 ipFragFails Counter RO The number of IP datagrams that have
been discarded because they needed to
be fragmented at this entity but could not
be, e.g., because their Don't Fragment
flag was set
1.3.6.1.2.1.4.19 ipFragCreates Counter RO The number of IP datagram fragments
that have been generated as a result of
fragmentation at this entity
1.3.6.1.2.1.4.20 ipAddrTable SEQUENCE The table of addressing information
OF relevant to this entity's IP addresses
IpAddrEntry
1.3.6.1.2.1.4.20.1 ipAddrEntry IpAddrEntry The addressing information for one of
this entity's IP addresses
1.3.6.1.2.1.4.20.1.1 ipAdEntAddr IpAddress RO The IP address to which this entry's
addressing information pertains
1.3.6.1.2.1.4.20.1.2 ipAdEntIfIndex INTEGER RO The index value which uniquely identifies
the interface to which this entry is
applicable
1.3.6.1.2.1.4.20.1.3 ipAdEntNetMask IpAddress RO The subnet mask associated with the IP
address of this entry
1.3.6.1.2.1.4.20.1.4 ipAdEntBcastAddr INTEGER RO The value of the least-significant bit in the
IP broadcast address used for sending
datagrams on the (logical) interface
associated with the IP address of this
entry
1.3.6.1.2.1.4.20.1.5 ipAdEntReasmMaxSize INTEGER RO The size of the largest IP datagram which
(0..65535) this entity can re-assemble from
incoming IP fragmented datagrams
received on this interface
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
1.3.6.1.2.1.4.21 ipRouteTable SEQUENCE This entity's IP Routing table

OF
IpRouteEntry
1.3.6.1.2.1.4.21.1 ipRouteEntry IpRouteEntry A route to a particular destination
1.3.6.1.2.1.4.21.1.1 ipRouteDest IpAddress RW The destination IP address of this route.
An entry with a value of 0.0.0.0 is
considered a default route
1.3.6.1.2.1.4.21.1.2 ipRouteIfIndex INTEGER RW The index value which uniquely identifies
the local interface through which the next
hop of this route should be reached
1.3.6.1.2.1.4.21.1.3 ipRouteMetric1 INTEGER RW The primary routing metric for this route
1.3.6.1.2.1.4.21.1.4 ipRouteMetric2 INTEGER RW An alternate routing metric for this route
1.3.6.1.2.1.4.21.1.7 ipRouteNextHop IpAddress RW The IP address of the next hop of this
route
1.3.6.1.2.1.4.21.1.8 ipRouteType INTEGER RW The type of route
1.3.6.1.2.1.4.21.1.9 ipRouteProto INTEGER RO The routing mechanism via which this
route was learned
1.3.6.1.2.1.4.21.1.10 ipRouteAge INTEGER RW The number of seconds since this route
was last updated or otherwise
determined to be correct
1.3.6.1.2.1.4.21.1.11 ipRouteMask IpAddress RW Indicate the mask to be logical-ANDed
with the destination address before being
compared to the value in the
ipRouteDest field
1.3.6.1.2.1.4.21.1.13 ipRouteInfo OBJECT RO A reference to MIB definitions specific to
IDENTIFIER the particular routing protocol which is
responsible for this route, as determined
by the value specified in the route's
ipRouteProto value
1.3.6.1.2.1.4.22 ipNetToMediaTable SEQUENCE The IP Address Translation table used

OF for mapping from IP addresses to
IpNetToMedia physical addresses
Entry
1.3.6.1.2.1.4.22.1 ipNetToMediaEntry IpNetToMedia Each entry contains one IpAddress to
Entry `physical' address equivalence
1.3.6.1.2.1.4.22.1.1 ipNetToMediaIfIndex INTEGER RW The interface on which this entry's
equivalence is effective
1.3.6.1.2.1.4.22.1.2 ipNetToMediaPhysAddres PhysAddress RW The media-dependent `physical' address
s
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.4.22.1.3 ipNetToMediaNetAddress IpAddress RW The IpAddress corresponding to the
media- dependent `physical' address
1.3.6.1.2.1.4.22.1.4 ipNetToMediaType INTEGER RW The type of mapping
1.3.6.1.2.1.4.23 ipRoutingDiscards Counter RO The number of routing entries which

though they are valid
1.3.6.1.2.1.5 icmp ICMP MIB, see mib-2.my

1.3.6.1.2.1.5.1 icmpInMsgs Counter RO The total number of ICMP messages
which the entity received
1.3.6.1.2.1.5.2 icmpInErrors Counter RO The number of ICMP messages which
the entity received but determined as
having ICMP-specific errors (bad ICMP
checksums, bad length, etc.)
1.3.6.1.2.1.5.3 icmpInDestUnreachs Counter RO The number of ICMP Destination
Unreachable messages received
1.3.6.1.2.1.5.4 icmpInTimeExcds Counter RO The number of ICMP Time Exceeded
messages received
1.3.6.1.2.1.5.5 icmpInParmProbs Counter RO The number of ICMP Parameter Problem
messages received
1.3.6.1.2.1.5.6 icmpInSrcQuenchs Counter RO The number of ICMP Source Quench
messages received
1.3.6.1.2.1.5.7 icmpInRedirects Counter RO The number of ICMP Redirect messages
received
1.3.6.1.2.1.5.8 icmpInEchos Counter RO The number of ICMP Echo (request)
messages received
1.3.6.1.2.1.5.9 icmpInEchoReps Counter RO The number of ICMP Echo Reply
messages received
1.3.6.1.2.1.5.10 icmpInTimestamps Counter RO The number of ICMP Timestamp
(request) messages received
1.3.6.1.2.1.5.11 icmpInTimestampReps Counter RO The number of ICMP Timestamp Reply
messages received
1.3.6.1.2.1.5.12 icmpInAddrMasks Counter RO The number of ICMP Address Mask
Request messages received
1.3.6.1.2.1.5.13 icmpInAddrMaskReps Counter RO The number of ICMP Address Mask
Reply messages received
1.3.6.1.2.1.5.14 icmpOutMsgs Counter RO The total number of ICMP messages
which this entity attempted to send
1.3.6.1.2.1.5.15 icmpOutErrors Counter RO The number of ICMP messages which
this entity did not send due to problems
discovered within ICMP such as a lack of
buffers
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.5.16 icmpOutDestUnreachs Counter RO The number of ICMP Destination
Unreachable messages sent
1.3.6.1.2.1.5.17 icmpOutTimeExcds Counter RO The number of ICMP Time Exceeded
messages sent
1.3.6.1.2.1.5.18 icmpOutParmProbs Counter RO The number of ICMP Parameter Problem
messages sent
1.3.6.1.2.1.5.19 icmpOutSrcQuenchs Counter RO The number of ICMP Source Quench
messages sent
1.3.6.1.2.1.5.20 icmpOutRedirects Counter RO The number of ICMP Redirect messages
sent
1.3.6.1.2.1.5.21 icmpOutEchos Counter RO The number of ICMP Echo (request)
messages sent
1.3.6.1.2.1.5.22 icmpOutEchoReps Counter RO The number of ICMP Echo Reply
messages sent
1.3.6.1.2.1.5.23 icmpOutTimestamps Counter RO The number of ICMP Timestamp
(request) messages sent
1.3.6.1.2.1.5.24 icmpOutTimestampReps Counter RO The number of ICMP Timestamp Reply
messages sent
1.3.6.1.2.1.5.25 icmpOutAddrMasks Counter RO The number of ICMP Address Mask
Request messages sent
1.3.6.1.2.1.5.26 icmpOutAddrMaskReps Counter RO The number of ICMP Address Mask
Reply messages sent
1.3.6.1.2.1.6 tcp TCP MIB, see mib-2.my

1.3.6.1.2.1.6.1 tcpRtoAlgorithm INTEGER RO The algorithm used to determine the
timeout value used for retransmitting
unacknowledged octets
1.3.6.1.2.1.6.2 tcpRtoMin INTEGER RO The minimum value permitted by a TCP
implementation for the retransmission
timeout, measured in milliseconds
1.3.6.1.2.1.6.3 tcpRtoMax INTEGER RO The maximum value permitted by a TCP
implementation for the retransmission
timeout, measured in milliseconds
1.3.6.1.2.1.6.4 tcpMaxConn INTEGER RO The limit on the total number of TCP
connections the entity can support. In
entities where the maximum number of
connections is dynamic, this object
should contain the value -1
1.3.6.1.2.1.6.5 tcpActiveOpens Counter RO The number of times TCP connections
have made a direct transition to the SYN-
SENT state from the CLOSED state
1.3.6.1.2.1.6.6 tcpPassiveOpens Counter RO The number of times TCP connections
have made a direct transition to the SYN-
RCVD state from the LISTEN state
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.6.7 tcpAttemptFails Counter RO The number of times TCP connections
have made a direct transition to the
CLOSED state from either the SYN-
SENT state or the SYN-RCVD state, plus
the number of times TCP connections
LISTEN state from the SYN-RCVD state
1.3.6.1.2.1.6.8 tcpEstabResets Counter RO The number of times TCP connections
CLOSED state from either the
ESTABLISHED state or the CLOSE-
WAIT state
1.3.6.1.2.1.6.9 tcpCurrEstab Gauge RO The number of TCP connections for
which the current state is either
ESTABLISHED or CLOSE- WAIT
1.3.6.1.2.1.6.10 tcpInSegs Counter RO The total number of segments received,
including those received in error
1.3.6.1.2.1.6.11 tcpOutSegs Counter RO The total number of segments sent,
including those on current connections
but excluding those containing only
retransmitted octets
1.3.6.1.2.1.6.12 tcpRetransSegs Counter RO The total number of segments
retransmitted - that is, the number of TCP
segments transmitted containing one or
more previously transmitted octets
1.3.6.1.2.1.6.13 tcpConnTable SEQUENCE A table containing TCP connection-

OF specific information
TcpConnEntry
1.3.6.1.2.1.6.13.1 tcpConnEntry TcpConnEntry Information about a particular current
TCP connection
1.3.6.1.2.1.6.13.1.1 tcpConnState INTEGER RW The state of this TCP connection
1.3.6.1.2.1.6.13.1.2 tcpConnLocalAddress IpAddress RO The local IP address for this TCP
connection
1.3.6.1.2.1.6.13.1.3 tcpConnLocalPort INTEGER RO The local port number for this TCP
(0..65535) connection
1.3.6.1.2.1.6.13.1.4 tcpConnRemAddress IpAddress RO The remote IP address for this TCP
connection
1.3.6.1.2.1.6.13.1.5 tcpConnRemPort INTEGER RO The remote port number for this TCP
(0..65535) connection
1.3.6.1.2.1.6.14 tcpInErrs Counter RO The total number of segments received

in error (e.g., bad TCP checksums)
1.3.6.1.2.1.6.15 tcpOutRsts Counter RO The number of TCP segments sent
containing the RST flag
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
1.3.6.1.2.1.7 udp UDP MIB, see mib-2.my

1.3.6.1.2.1.7.1 udpInDatagrams Counter RO The total number of UDP datagrams
delivered to UDP users
1.3.6.1.2.1.7.2 udpNoPorts Counter RO The total number of received UDP
datagrams for which there was no
application at the destination port
1.3.6.1.2.1.7.3 udpInErrors Counter RO The number of received UDP datagrams
that could not be delivered for reasons
other than the lack of an application at
the destination port
1.3.6.1.2.1.7.4 udpOutDatagrams Counter RO The total number of UDP datagrams sent
from this entity
1.3.6.1.2.1.7.5 udpTable SEQUENCE A table containing UDP listener

OF UdpEntry information
1.3.6.1.2.1.7.5.1 udpEntry udpEntry Information about a particular current
UDP listener
1.3.6.1.2.1.7.5.1.1 udpLocalAddress IpAddress RO The local IP address for this UDP listener
1.3.6.1.2.1.7.5.1.2 udpLocalPort INTEGER RO The local port number for this UDP
(0..65535) listener
1.3.6.1.2.1.8 egp EGP MIB, see mib-2.my

1.3.6.1.2.1.8.1 egpInMsgs Counter RO The number of EGP messages received
without error
1.3.6.1.2.1.8.2 egpInErrors Counter RO The number of EGP messages received
that proved to be in error
1.3.6.1.2.1.8.3 egpOutMsgs Counter RO The total number of locally generated
EGP messages
1.3.6.1.2.1.8.4 egpOutErrors Counter RO The number of locally generated EGP
messages not sent due to resource
limitations within an EGP entity
1.3.6.1.2.1.8.5 egpNeighTable SEQUENCE The EGP neighbor table

OF
EgpNeighEntr
y
1.3.6.1.2.1.8.5.1 egpNeighEntry EgpNeighEntr Information about this entity's
y relationship with a particular EGP
neighbor
1.3.6.1.2.1.8.5.1.1 egpNeighState INTEGER RO The EGP state of the local system with
respect to this entry's EGP neighbor
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.8.5.1.2 egpNeighAddr IpAddress RO The IP address of this entry's EGP
neighbor
1.3.6.1.2.1.8.5.1.3 egpNeighAs INTEGER RO The autonomous system of this EGP
peer
1.3.6.1.2.1.8.5.1.4 egpNeighInMsgs Counter RO The number of EGP messages received
without error from this EGP peer
1.3.6.1.2.1.8.5.1.5 egpNeighInErrs Counter RO The number of EGP messages received
from this EGP peer that proved to be in
error (e.g., bad EGP checksum)
1.3.6.1.2.1.8.5.1.6 egpNeighOutMsgs Counter RO The number of locally generated EGP
messages to this EGP peer
1.3.6.1.2.1.8.5.1.7 egpNeighOutErrs Counter RO The number of locally generated EGP
messages not sent to this EGP peer due
to resource limitations within an EGP
entity
1.3.6.1.2.1.8.5.1.8 egpNeighInErrMsgs Counter RO The number of EGP-defined error
messages received from this EGP peer
1.3.6.1.2.1.8.5.1.9 egpNeighOutErrMsgs Counter RO The number of EGP-defined error
messages sent to this EGP peer
1.3.6.1.2.1.8.5.1.10 egpNeighStateUps Counter RO The number of EGP state transitions to
the UP state with this EGP peer
1.3.6.1.2.1.8.5.1.11 egpNeighStateDowns Counter RO The number of EGP state transitions
from the UP state to any other state with
this EGP peer
1.3.6.1.2.1.8.5.1.12 egpNeighIntervalHello INTEGER RO The interval between EGP Hello
command retransmissions (in
hundredths of a second)
1.3.6.1.2.1.8.5.1.13 egpNeighIntervalPoll INTEGER RO The interval between EGP poll command
retransmissions (in hundredths of a
second)
1.3.6.1.2.1.8.5.1.14 egpNeighMode INTEGER RO The polling mode of this EGP entity,
either passive or active
active(1), passive(2)
1.3.6.1.2.1.8.5.1.15 egpNeighEventTrigger INTEGER RW A control variable used to trigger
operator- initiated Start and Stop events
start(1), stop(2)
1.3.6.1.2.1.8.6 egpAs INTEGER RO The autonomous system number of this

EGP entity
1.3.6.1.2.1.10 transmission Transmission MIB, see rfc2127.my

1.3.6.1.2.1.10.20 isdnMib The MIB module to describe the
management of ISDN interfaces
1.3.6.1.2.1.10.20.1 isdnMibObjects ISDN MIB object definitions
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.1.1 isdnBasicRateGroup This group describes physical basic rate
interfaces
1.3.6.1.2.1.10.20.1.1.1 isdnBasicRateTable SEQUENCE Table containing configuration and
OF operational parameters for all physical
IsdnBasicRate Basic Rate interfaces on this managed
Entry device
1.3.6.1.2.1.10.20.1.1.1.1 isdnBasicRateEntry IsdnBasicRate An entry in the ISDN Basic Rate Table
Entry
1.3.6.1.2.1.10.20.1.1.1.1 isdnBasicRateIfType INTEGER RW The physical interface type
.1 For 'S/T' interfaces, also called 'Four-
wire Basic Access Interface', the value of
this object is isdns(75).
For 'U' interfaces, also called 'Two-wire
Basic Access Interface', the value of this
object is isdnu(76)
1.3.6.1.2.1.10.20.1.1.1.1 isdnBasicRateLineTopolog INTEGER RW The line topology to be used for this
.2 y interface
pointToPoint(1), pointToMultipoint(2)
1.3.6.1.2.1.10.20.1.1.1.1 isdnBasicRateIfMode INTEGER RW The physical interface mode. For TE
.3 mode, the value of this object is te(1). For
NT mode, the value of this object is nt(2)
1.3.6.1.2.1.10.20.1.1.1.1 isdnBasicRateSignalMode INTEGER RW The signaling channel operational mode
.4 for this interface. If active(1) there is a
signaling channel on this interface. If
inactive(2) a signaling channel is not
available.
1.3.6.1.2.1.10.20.1.2 isdnBearerGroup This group describes physical basic rate

interfaces
1.3.6.1.2.1.10.20.1.2.1 isdnBearerTable SEQUENCE This table defines port specific
OF operational, statistics and active call data
IsdnBearerEnt for ISDN B channels. Each entry in this
ry table describes one B (bearer) channel
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerEntry IsdnBearerEnt Operational and statistics information
ry relating to one port. A port is a single B
channel
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerChannelType INTEGER RW The B channel type. If the B channel is
.1 connected to a dialup line, this object has
a value of dialup(1). In this case, it is
controlled by an associated signaling
channel. If the B channel is connected to
a leased line, this object has a value of
leased(2). For leased line B channels,
there is no signaling channel control
available
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerOperStatus INTEGER RO The current call control state for this port.
.2 idle(1): The B channel is idle, no call or
call attempt is going on.
connecting(2): A connection attempt
(outgoing call) is being made on this
interface.
connected(3): An incoming call is in the
process of validation.
active(4): A call is active on this interface
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerChannelNumbe INTEGER RO The identifier being used by a signaling
.3 r (1..30) protocol to identify this B channel, also
referred to as B channel number
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerPeerAddress DisplayString RO The ISDN address the current or last call
.4 is or was connected to
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerPeerSubAddres DisplayString RO The ISDN subaddress the current or last
.5 s call is or was connected to
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerCallOrigin INTEGER RO The call origin for the current or last call
.6 unknown(1), originate(2), answer(3),
callback(4)
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerInfoType INTEGER RO The Information Transfer Capability for
.7 the current or last call. speech(2) refers
to a non-data connection, whereas
audio31(6) and audio7(7) refer to data
mode connections
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerMultirate TruthValue RO This flag indicates if the current or last
.8 call used multirate
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerCallSetupTime TimeStamp RO The value of sysUpTime when the ISDN
.9 setup message for the current or last call
was sent or received
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerCallConnectTim TimeStamp RO The value of sysUpTime when the ISDN
.10 e connect message for the current or last
call was sent or received
1.3.6.1.2.1.10.20.1.2.1.1 isdnBearerChargedUnits Gauge32 RO The number of charged units for the
.11 current or last connection
1.3.6.1.2.1.10.20.1.3 isdnSignalingGroup Signaling channel configuration table

1.3.6.1.2.1.10.20.1.3.1 isdnSignalingGetIndex TestAndIncr RW The recommended procedure for
selecting a new index for
isdnSignalingTable row creation is to
GET the value of this object, and then to
SET the object with the same value. If the
SET operation succeeds, the manager
can use this value as an index to create
a new row in this table
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.1.3.2 isdnSignalingTable SEQUENCE ISDN signaling table containing
OF configuration and operational
IsdnSignaling parameters for all ISDN signaling
Entry channels on this managed device
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingEntry IsdnSignaling An entry in the ISDN Signaling Table
Entry
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingIndex INTEGER The index value which uniquely identifies
.1 (1..214748364 an entry in the isdnSignalingTable
7)
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingIfIndex InterfaceIndex RO The ifIndex value of the interface
.2 associated with this signaling channel
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingProtocol IsdnSignaling RC The particular protocol type supported by
.3 Protocol the switch providing access to the ISDN
network to which this signaling channel is
connected
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingCallingAddre DisplayString RC The ISDN Address to be assigned to this
.4 ss signaling channel
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingSubAddress DisplayString RC Supplementary information to the ISDN
.5 address assigned to this signaling
channel
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingBchannelCo Integer32 RC The total number of B channels (bearer
.6 unt (1..65535) channels) managed by this signaling
channel
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingInfoTrapEna INTEGER RC Indicates whether
.7 ble isdnMibCallInformation traps should be
generated for calls on this signaling
channel
1.3.6.1.2.1.10.20.1.3.2.1 isdnSignalingStatus RowStatus RC This object is used to create and delete
.8 rows in the isdnSignalingTable
1.3.6.1.2.1.10.20.1.3.3 isdnSignalingStatsTable SEQUENCE ISDN signaling table containing statistics

OF information for all ISDN signaling
IsdnSignaling channels on this managed device
StatsEntry
1.3.6.1.2.1.10.20.1.3.3.1 isdnSignalingStatsEntry IsdnSignaling An entry in the ISDN Signaling statistics
StatsEntry Table
1.3.6.1.2.1.10.20.1.3.3.1 isdnSigStatsInCalls Counter32 RO The number of incoming calls on this
.1 interface
1.3.6.1.2.1.10.20.1.3.3.1 isdnSigStatsInConnected Counter32 RO The number of incoming calls on this
.2 interface which were actually connected
1.3.6.1.2.1.10.20.1.3.3.1 isdnSigStatsOutCalls Counter32 RO The number of outgoing calls on this
.3 interface
1.3.6.1.2.1.10.20.1.3.3.1 isdnSigStatsOutConnected Counter32 RO The number of outgoing calls on this
.4 interface which were actually connected
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.1.3.3.1 isdnSigStatsChargedUnits Counter32 RO The number of charging units on this
.5 interface since system startup
1.3.6.1.2.1.10.20.1.3.4 isdnLapdTable SEQUENCE Table containing configuration and

OF statistics information for all LAPD (D
IsdnLapdEntry channel Data Link) interfaces on this
managed device
1.3.6.1.2.1.10.20.1.3.4.1 isdnLapdEntry An entry in the LAPD Table
IsdnLapdEntry
1.3.6.1.2.1.10.20.1.3.4.1 isdnLapdPrimaryChannel TruthValue RW If set to true(1), this D channel is the
.1 designated primary D channel if D
channel backup is active
1.3.6.1.2.1.10.20.1.3.4.1 isdnLapdOperStatus INTEGER RO The operational status of this interface
.2
1.3.6.1.2.1.10.20.1.3.4.1 isdnLapdPeerSabme Counter32 RO The number of peer SABME frames
.3 received on this interface
1.3.6.1.2.1.10.20.1.3.4.1 isdnLapdRecvdFrmr Counter32 RO The number of LAPD FRMR response
.4 frames received
1.3.6.1.2.1.10.20.1.4 isdnEndpointGroup The Terminal Endpoint group and table

1.3.6.1.2.1.10.20.1.4.1 isdnEndpointGetIndex The recommended procedure for
selecting a new index for
isdnEndpointTable row creation is to
GET the value of this object, and then to
SET the object with the same value. If the
SET operation succeeds, the manager
can use this value as an index to create
a new row in this table
1.3.6.1.2.1.10.20.1.4.2 isdnEndpointTable SEQUENCE Table containing configuration for
OF Terminal Endpoints
IsdnEndpointE
ntry
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointEntry IsdnEndpointE An entry in the Terminal Endpoint Table
ntry
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointIndex INTEGER The index value which uniquely identifies
.1 (1..214748364 an entry in the isdnEndpointTable
7)
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointIfIndex InterfaceIndex RO The ifIndex value of the interface
.2 associated with this Terminal Endpoint
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointIfType IANAifType RC The interface type for this Terminal
.3 Endpoint. Interface types of x25ple(40)
and isdn(63) are allowed
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointTeiType INTEGER RC The type of TEI (Terminal Endpoint
.4 Identifier) used for this Terminal
Endpoint. In case of dynamic(1), the TEI
value is selected by the switch. In case of
static(2), a valid TEI value has to be
entered in the isdnEndpointTeiValue
object
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointTeiValue INTEGER ( RC The TEI (Terminal Endpoint Identifier)
.5 0..255 ) value for this Terminal Endpoint
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointSpid DisplayString RC The Service profile IDentifier (SPID)
.6 information for this Terminal Endpoint
1.3.6.1.2.1.10.20.1.4.2.1 isdnEndpointStatus RowStatus RC This object is used to create and delete
.7 rows in the isdnEndpointTable
1.3.6.1.2.1.10.20.1.5 isdnDirectoryGroup The Directory Number group

1.3.6.1.2.1.10.20.1.5.1 isdnDirectoryTable SEQUENCE Table containing Directory Numbers
OF
IsdnDirectoryE
ntry
1.3.6.1.2.1.10.20.1.5.1.1 isdnDirectoryEntry IsdnDirectoryE An entry in the Directory Number Table
ntry
1.3.6.1.2.1.10.20.1.5.1.1 isdnDirectoryIndex INTEGER ( The index value which uniquely identifies
.1 1..'7fffffff'h ) an entry in the isdnDirectoryTable
1.3.6.1.2.1.10.20.1.5.1.1 isdnDirectoryNumber DisplayString RC A Directory Number. Directory Numbers
.2 are used to identify incoming calls on the
signaling channel given in
isdnDirectorySigIndex
1.3.6.1.2.1.10.20.1.5.1.1 isdnDirectorySigIndex INTEGER RC An index pointing to an ISDN signaling
.3 (1..214748364 channel
7)
1.3.6.1.2.1.10.20.1.5.1.1 isdnDirectoryStatus RowStatus RC This object is used to create and delete
.4 rows in the isdnDirectoryTable
1.3.6.1.2.1.10.20.2 isdnMibTrapPrefix
1.3.6.1.2.1.10.20.2.0 isdnMibTraps
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.10.20.2.0.1 isdnMibCallInformation TRAP This trap/inform is sent to the manager
under the following condidions:
- on incoming calls for each call which is
rejected for policy reasons (e.g. unknown
neighbor or access violation)
- on outgoing calls whenever a call
attempt is determined to have ultimately
failed. In the event that call retry is active,
then this will be after all retry attempts
have failed.
- whenever a call connects. In this case,
the object isdnBearerCallConnectTime
should be included in the trap.
1.3.6.1.2.1.10.20.3 isdnMibConformance
1.3.6.1.2.1.10.20.3.1 isdnMibCompliances
1.3.6.1.2.1.10.20.3.2 isdnMibGroups
1.3.6.1.2.1.11 snmp SNMP MIB, see mib-2.my

1.3.6.1.2.1.11.1 snmpInPkts Counter RO The total number of Messages delivered
to the SNMP entity from the transport
service
1.3.6.1.2.1.11.2 snmpOutPkts Counter RO The total number of SNMP Messages
which were passed from the SNMP
protocol entity to the transport service
1.3.6.1.2.1.11.3 snmpInBadVersions Counter RO The total number of SNMP Messages
which were delivered to the SNMP
protocol entity and were for an
unsupported SNMP version
1.3.6.1.2.1.11.4 snmpInBadCommunityNa Counter RO The total number of SNMP Messages
mes delivered to the SNMP protocol entity
which used a SNMP community name
not known to said entity
1.3.6.1.2.1.11.5 snmpInBadCommunityUse Counter RO The total number of SNMP Messages
s delivered to the SNMP protocol entity
which represented an SNMP operation
which was not allowed by the SNMP
community named in the Message
1.3.6.1.2.1.11.6 snmpInASNParseErrs Counter RO The total number of ASN.1 or BER errors
encountered by the SNMP protocol entity
when decoding received SNMP
Messages
1.3.6.1.2.1.11.7 not used
1.3.6.1.2.1.11.8 snmpInTooBigs Counter RO The total number of SNMP PDUs which
were delivered to the SNMP protocol
entity and for which the value of the error-
status field is `tooBig'
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.11.9 snmpInNoSuchNames Counter RO The total number of SNMP PDUs which
status field is `noSuchName'
1.3.6.1.2.1.11.10 snmpInBadValues Counter RO The total number of SNMP PDUs which
status field is `badValue'
1.3.6.1.2.1.11.11 snmpInReadOnlys Counter RO The total number valid SNMP PDUs
which were delivered to the SNMP
protocol entity and for which the value of
the error-status field is `readOnly'
1.3.6.1.2.1.11.12 snmpInGenErrs Counter RO The total number of SNMP PDUs which
status field is `genErr'
1.3.6.1.2.1.11.13 snmpInTotalReqVars Counter RO The total number of MIB objects which
have been retrieved successfully by the
SNMP protocol entity as the result of
receiving valid SNMP Get-Request and
Get-Next PDUs
1.3.6.1.2.1.11.14 snmpInTotalSetVars Counter RO The total number of MIB objects which
have been altered successfully by the
SNMP protocol entity as the result of
receiving valid SNMP Set-Request
PDUs
1.3.6.1.2.1.11.15 snmpInGetRequests Counter RO The total number of SNMP Get-Request
PDUs which have been accepted and
processed by the SNMP protocol entity
1.3.6.1.2.1.11.16 snmpInGetNexts Counter RO The total number of SNMP Get-Next
1.3.6.1.2.1.11.17 snmpInSetRequests Counter RO The total number of SNMP Set-Request
1.3.6.1.2.1.11.18 snmpInGetResponses Counter RO The total number of SNMP Get-
Response PDUs which have been
accepted and processed by the SNMP
protocol entity
1.3.6.1.2.1.11.19 snmpInTraps Counter RO The total number of SNMP Trap PDUs
which have been accepted and
1.3.6.1.2.1.11.20 snmpOutTooBigs Counter RO The total number of SNMP PDUs which
were generated by the SNMP protocol
status field is `tooBig.'
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.11.21 snmpOutNoSuchNames Counter RO The total number of SNMP PDUs which
status is `noSuchName'
1.3.6.1.2.1.11.22 snmpOutBadValues Counter RO The total number of SNMP PDUs which
status field is `badValue'
1.3.6.1.2.1.11.23 not used
1.3.6.1.2.1.11.24 snmpOutGenErrs Counter RO The total number of SNMP PDUs which
status field is `genErr'
1.3.6.1.2.1.11.25 snmpOutGetRequests Counter RO The total number of SNMP Get-Request
PDUs which have been generated by the
SNMP protocol entity
1.3.6.1.2.1.11.26 snmpOutGetNexts Counter RO The total number of SNMP Get-Next
1.3.6.1.2.1.11.27 snmpOutSetRequests Counter RO The total number of SNMP Set-Request
1.3.6.1.2.1.11.28 snmpOutGetResponses Counter RO The total number of SNMP Get-
Response PDUs which have been
generated by the SNMP protocol entity
1.3.6.1.2.1.11.29 snmpOutTraps Counter RO The total number of SNMP Trap PDUs
which have been generated by the
1.3.6.1.2.1.11.30 snmpEnableAuthenTraps INTEGER RW Indicates whether the SNMP agent
process is permitted to generate
authentication-failure traps.
enabled(1), disabled(2)
1.3.6.1.2.1.16 rmon RMON MIB, see my_rmon2.my

1.3.6.1.2.1.16.19 probeConfig This group controls the configuration of
various operating parameters of the
probe
1.3.6.1.2.1.16.19.1 probeCapabilities BITS RO This group controls the configuration of
various operating parameters of the
probe
1.3.6.1.2.1.16.19.2 probeSoftwareRev DisplayString RO The software revision of this device
(SIZE(0..15))
1.3.6.1.2.1.16.19.3 probeHardwareRev DisplayString RO The hardware revision of this device
(SIZE(0..31))
1.3.6.1.2.1.16.19.4 probeDateTime OCTET RW Probe's current date and time
STRING
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.16.19.5 probeResetControl INTEGER RW Setting this object to warmBoot(2)
causes the device to restart the
application software with current
configuration parameters saved in non-
volatile memory.
Setting this object to coldBoot(3) causes
the device to reinitialize configuration
parameters in non-volatile memory to
default values and restart the application
software.
When the device is running normally, this
variable has a value of running(1)
1.3.6.1.2.1.16.19.6 probeDownloadFile DisplayString RW The file name to be downloaded from the
(SIZE(0..127)) TFTP server when a download is next
requested via this MIB
1.3.6.1.2.1.16.19.7 probeDownloadTFTPServ IpAddress RW The IP address of the TFTP server that
er contains the boot image to load when a
download is next requested via this MIB
1.3.6.1.2.1.16.19.8 probeDownloadAction INTEGER RW When this object is set to
downloadToRAM(2) or
downloadToPROM(3), the device will
discontinue its normal operation and
begin download of the image specified by
probeDownloadFile from the server
specified by probeDownloadTFTPServer
using the TFTP protocol.
If downloadToRAM(2) is specified, the
new image is copied to RAM only (the old
image remains unaltered in the flash
EPROM).
If downloadToPROM(3) is specified, the
new image is written to the flash EPROM
memory after its checksum has been
verified to be correct.
When the download process is
completed, the device will warm boot to
restart the newly loaded application.
When the device is not downloading, this
object will have a value of
notDownloading(1).
1.3.6.1.2.1.16.19.9 probeDownloadStatus INTEGER RO The status of the last download
procedure, if any. This object will have a
value of downloadStatusUnknown(2) if
no download process has been
performed
1.3.6.1.2.1.16.19.13 trapDestTable SEQUENCE A list of trap destination entries

OF
TrapDestEntry
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.16.19.13.1 trapDestEntry TrapDestEntry This entry includes a destination IP
address to which to send traps for this
community
1.3.6.1.2.1.16.19.13.1.1 trapDestIndex Integer32 A value that uniquely identifies this
(1..65535) trapDestEntry
1.3.6.1.2.1.16.19.13.1.2 trapDestCommunity OCTET RC A community to which this destination
STRING address belongs
(SIZE(0..127))
1.3.6.1.2.1.16.19.13.1.3 trapDestProtocol INTEGER RC The protocol with which to send this trap
ip(1), ipx(2)
1.3.6.1.2.1.16.19.13.1.4 trapDestAddress OCTET RC The address to send traps on behalf of
STRING this entry
1.3.6.1.2.1.16.19.13.1.5 trapDestOwner DisplayString RC The entity that configured this entry and
is therefore using the resources assigned
to it
1.3.6.1.2.1.16.19.13.1.6 trapDestStatus RowStatus RC The status of this trap destination entry
1.3.6.1.2.1.30 ianaifType IANA MIB, see iana.my

The MIB module which defines the
IANAifType textual convention, and thus
the enumerated values of the ifType
object defined in MIB-II's ifTable
1.3.6.1.2.1.31 ifMIB IF MIB, see rfc2233.my

The MIB module to describe generic
objects for network interface sub-layers.
This MIB is an updated version of MIB-
II's ifTable, and incorporates the
extensions defined in RFC 1229.
1.3.6.1.2.1.31.1 ifMIBObjects
1.3.6.1.2.1.31.1.1 ifXTable SEQUENCE A list of interface entries. The number of
OF IfXEntry entries is given by the value of ifNumber.
This table contains additional objects for
the interface table.
1.3.6.1.2.1.31.1.1.1 ifXEntry IfXEntry An entry containing additional
management information applicable to a
particular interface.
1.3.6.1.2.1.31.1.1.1.1 ifName DisplayString RO The textual name of the interface.
1.3.6.1.2.1.31.1.1.1.2 ifInMulticastPkts Counter RO The number of packets, delivered by this
were addressed to a multicast address at
this sub-layer.
1.3.6.1.2.1.31.1.1.1.3 ifInBroadcastPkts Counter RO The number of packets, delivered by this
were addressed to a broadcast address
at this sub-layer.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.31.1.1.1.4 ifOutMulticastPkts Counter RO The total number of packets that higher-
address at this sub-layer, including those
that were discarded or not sent.
1.3.6.1.2.1.31.1.1.1.5 ifOutBroadcastPkts Counter RO The total number of packets that higher-
and which were addressed to a
broadcast address at this sub-layer,
not sent.
1.3.6.1.2.1.31.1.1.1.6 ifHCInOctets Counter64 RO The total number of octets received on
the interface, including framing
characters.
1.3.6.1.2.1.31.1.1.1.7 ifHCInUcastPkts Counter64 RO The number of packets, delivered by this
were not addressed to a multicast or
1.3.6.1.2.1.31.1.1.1.8 ifHCInMulticastPkts Counter64 RO The number of packets, delivered by this
were addressed to a multicast address at
this sub-layer.
1.3.6.1.2.1.31.1.1.1.9 ifHCInBroadcastPkts Counter64 RO The number of packets, delivered by this
were addressed to a broadcast address
at this sub-layer.
1.3.6.1.2.1.31.1.1.1.10 ifHCOutOctets Counter64 RO The total number of octets transmitted
out of the interface, including framing
characters.
1.3.6.1.2.1.31.1.1.1.11 ifHCOutUcastPkts Counter64 RO The total number of packets that higher-
and which were not addressed to a
multicast or broadcast address at this
sub-layer, including those that were
discarded or not sent.
1.3.6.1.2.1.31.1.1.1.12 ifHCOutMulticastPkts Counter64 RO The total number of packets that higher-
address at this sub-layer, including those
that were discarded or not sent.
1.3.6.1.2.1.31.1.1.1.13 ifHCOutBroadcastPkts Counter64 RO The total number of packets that higher-
and which were addressed to a
broadcast address at this sub-layer,
not sent.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.31.1.1.1.14 ifLinkUpDownTrapEnable INTEGER RW Indicates whether linkUp/linkDown traps
should be generated for this interface.
enabled(1), disabled(2)
1.3.6.1.2.1.31.1.1.1.15 ifHighSpeed Gauge RO An estimate of the interface's current
bandwidth in units of 1,000,000 bits per
second.
1.3.6.1.2.1.31.1.1.1.16 ifPromiscuousMode TruthValue RW ’true(1)’ when the station accepts all
packets/frames transmitted on the
media.
’false(2)’ if this interface only accepts
packets/frames that are addressed to
this station.
1.3.6.1.2.1.31.1.1.1.17 ifConnectorPresent TruthValue RO 'true(1)' if the interface sublayer has a
physical connector
’false(2)' otherwise.
1.3.6.1.2.1.31.1.1.1.18 ifAlias DisplayString RW This object is an 'alias' name for the
interface as specified by a network
manager, and provides a nonvolatile
'handle' for the interface.
1.3.6.1.2.1.31.1.1.1.19 ifCounterDiscontinuityTime TimeStamp RO The value of sysUpTime on the most
recent occasion at which any one or
more of this interface's counters suffered
a discontinuity.
1.3.6.1.2.1.31.1.2 ifStackTable SEQUENCE The table containing information on the

OF relationships between the multiple sub-
IfStackEntry layers of network interfaces.
1.3.6.1.2.1.31.1.2.1 ifStackEntry IfStackEntry Information on a particular relationship
between two sub-layers, specifying that
one sub-layer runs on 'top' of the other
sub-layer.
1.3.6.1.2.1.31.1.2.1.1 ifStackHigherLayer Integer32 The value of ifIndex corresponding to the
higher sub-layer of the relationship, i.e.,
the sub-layer which runs on 'top' of the
sub-layer identified by the corresponding
instance of ifStackLowerLayer.
1.3.6.1.2.1.31.1.2.1.2 ifStackLowerLayer Integer32 The value of ifIndex corresponding to the
lower sub- layer of the relationship, i.e.,
the sub-layer which runs 'below' the sub-
layer identified by the corresponding
instance of ifStackHigherLayer.
1.3.6.1.2.1.31.1.2.1.3 ifStackStatus RowStatus RC The status of the relationship between
two sub- layers.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.31.1.3 ifTestTable SEQUENCE This table contains one entry per
OF IfTestEntry interface. It defines objects which allow
a network manager to instruct an agent
to test an interface for various faults.
Deprecated
1.3.6.1.2.1.31.1.3.1 ifTestEntry IfTestEntry An entry containing objects for invoking
tests on an interface.
Deprecated
1.3.6.1.2.1.31.1.3.1.1 ifTestId TestAndIncr RW This object identifies the current
invocation of the interface's test
Deprecated
1.3.6.1.2.1.31.1.3.1.2 ifTestStatus INTEGER RW This object indicates whether or not
some manager currently has the
necessary 'ownership' required to invoke
a test on this interface
Deprecated
1.3.6.1.2.1.31.1.3.1.3 ifTestType AutonomousT RW A control variable used to start and stop
ype operator- initiated interface tests
Deprecated
1.3.6.1.2.1.31.1.3.1.4 ifTestResult INTEGER RO This object contains the result of the
most recently requested test, or the value
none(1) if no tests have been requested
since the last reset
Deprecated
1.3.6.1.2.1.31.1.3.1.5 ifTestCode OBJECT RO This object contains a code which
IDENTIFIER contains more specific information on the
test result, for example an error-code
after a failed test
Deprecated
1.3.6.1.2.1.31.1.3.1.6 ifTestOwner OwnerString RW The entity which currently has the
'ownership' required to invoke a test on
this interface
Deprecated
1.3.6.1.2.1.31.1.4 ifRcvAddressTable SEQUENCE This table contains an entry for each

OF address (broadcast, multicast, or uni-
IfRcvAddress cast) for which the system will receive
Entry packets/frames on a particular interface.
1.3.6.1.2.1.31.1.4.1 ifRcvAddressEntry IfRcvAddress A list of objects identifying an address for
Entry which the system will accept packets/
frames on the particular interface
identified by the index value ifIndex.
1.3.6.1.2.1.31.1.4.1.1 ifRcvAddressAddress PhysAddress An address for which the system will
accept packets/frames on this entry's
interface.
1.3.6.1.2.1.31.1.4.1.2 ifRcvAddressStatus RowStatus RC This object is used to create and delete
rows in the ifRcvAddressTable.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.2.1.31.1.4.1.3 ifRcvAddressType INTEGER RC This object has the value nonVolatile(3)
for those entries in the table which are
valid and will not be deleted by the next
restart of the managed system. Entries
having the value volatile(2) are valid and
exist, but have not been saved, so that
will not exist after the next restart of the
managed system. Entries having the
value other(1) are valid and exist but are
not classified as to whether they will
continue to exist after the next restart.
1.3.6.1.2.1.31.1.5 ifTableLastChange TimeTicks The value of sysUpTime at the time of the

last creation or deletion of an entry in the
ifTable. If the number of entries has been
unchanged since the last re-initialization
of the local network management
subsystem, then this object contains a
zero value.
1.3.6.1.2.1.31.1.6 ifStackLastChange TimeTicks RO The value of sysUpTime at the time of the
last change of the (whole) interface
stack.

1.3.6.1.4.1.231.7.2.7 hg3550mib hg3550 MIB, see hg1500.my
1.3.6.1.4.1.231.7.2.7.1 errorSigGrouphlb20 Error Signalisation Group MIB containing
administration-level trap event history
1.3.6.1.4.1.231.7.2.7.1.1 numberOfTrapHistoryEntri INTEGER RW Contains the number of traps to be found

es in the trap history table. This value can be
used to delete all entries (value = 0).
1.3.6.1.4.1.231.7.2.7.1.2 hlb20TrapHistoryTable SEQUENCE This table contains information about
OF traps sent by the device.
Hlb20TrapHist
oryEntry
1.3.6.1.4.1.231.7.2.7.1.2 hlb20TrapHistoryEntry Hlb20TrapHist The trap history table entries.
.1 oryEntry
1.3.6.1.4.1.231.7.2.7.1.2 trapIndex INTEGER RO Identification of an table entry enabled by
.1.1 this index.
1.3.6.1.4.1.231.7.2.7.1.2 trapDateTime DateAndTime RO Time, when the trap event occurred.
.1.2
Table 15 Data in the SNI specific MIB
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.1.2 trapSeverity INTEGER RO Contains information about the error
.1.3 severity.
- normal(1)
- warning(2)
- minor(3)
- major(4)
- critical(5)
1.3.6.1.4.1.231.7.2.7.1.2 trapErrorClass INTEGER RO Contains the error class number (type of
.1.4 trap).
- general(1)
- voice(2)
- data(3)
- security(4)
- client(5)
1.3.6.1.4.1.231.7.2.7.1.2 trapErrorCode INTEGER RO Contains the error code.
.1.5
1.3.6.1.4.1.231.7.2.7.1.2 trapDescription DisplayString RO Detailed information about the trap
.1.6 event.
1.3.6.1.4.1.231.7.2.7.1.2 trapHandling INTEGER RO Forwarded(1), if the error produced a
.1.7 trap.
Stored(2), if the error data was stored
without sending a trap.
1.3.6.1.4.1.231.7.2.7.1.3 numberOfErrorTableEntrie INTEGER RW Contains the number of traps to be found

s in the trap history table. This value can be
used to delete all entries (value = 0).
deprecated
1.3.6.1.4.1.231.7.2.7.1.4 hlb20ErrorTable SEQUENCE This table contains information about
OF expert level error events that occur on
Hlb20ErrorEnt the hg3550 device.
ry deprecated
1.3.6.1.4.1.231.7.2.7.1.4 hlb20ErrorEntry Hlb20ErrorEnt The trap history table entries.
.1 ry deprecated
1.3.6.1.4.1.231.7.2.7.1.4 errorIndex INTEGER RO Contains the error/trace class.
.1.1 deprecated
1.3.6.1.4.1.231.7.2.7.1.4 errorTimeStamp OCTET RO System-specific timestamp for the error.
.1.2 STRING deprecated
1.3.6.1.4.1.231.7.2.7.1.4 errorClass INTEGER RO Contains the error/trace class.
.1.3 deprecated
1.3.6.1.4.1.231.7.2.7.1.4 errorDescription DisplayString RO Detailed information about errors.
.1.4 deprecated
1.3.6.1.4.1.231.7.2.7.2 controlGrouphlb20 Control Group MIB

1.3.6.1.4.1.231.7.2.7.2.1 indexOfLastTrapSent INTEGER RO Contains the index of the last trap which
was sent.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.2.2 trapTypesToBeSent INTEGER RW Defines which error events are signalled
as a trap.
1.3.6.1.4.1.231.7.2.7.2.3 sysState INTEGER RW The actual error state of the hg3550
device.
- normal(1)
- warning(2)
- minor(3)
- major(4)
- critical(5)
1.3.6.1.4.1.231.7.2.7.2.4 sysConnectionState INTEGER RO Indicates if the connection between
Hicom 150E Office and hg3550 / Hicom
Xpress @LAN was successfully
established.
- disconnected(1)
- connected(2)
1.3.6.1.4.1.231.7.2.7.2.5 sysMacAddress DisplayString RO Contains the MAC Address of this
device.
(Object not available in hg3550 / Xpress
@LAN 1.0)
1.3.6.1.4.1.231.7.2.7.2.6 sysSoftwareVersion DisplayString RO Contains the version string of the system
software.
(Object not available in HG1500 / Xpress
@LAN 1.0)
1.3.6.1.4.1.231.7.2.7.2.7 sysSnmpAgentVersion DisplayString RO Version number of the systems SNMP
agent (formatting: x.y.z.)
1.3.6.1.4.1.231.7.2.7.2.8 sysShadowSoftwareVersio DisplayString RO Contains the version string of the inactive
n software version (flash image) that had
been transferred to the device recently.
@LAN 1.0)
deprecated
1.3.6.1.4.1.231.7.2.7.2.9 sysHardwareVersion DisplayString RO Hardware version identifier of the device.
@LAN 1.0)
1.3.6.1.4.1.231.7.2.7.2.1 sysOperatingMode INTEGER RO Operating mode of the device. In
0 standard mode (1), the device serves as
a normal gateway. In gatekeeper mode
(2), it additionally operates as a
gatekeeper for voice over IP endpoints.
@LAN 1.0)
1.3.6.1.4.1.231.7.2.7.2.1 sysSwitchoverDateTime DateAndTime RW Date and time for the switchover to the
1 new system software.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.2.1 sysDownloadAction INTEGER RW When this object is set to
2 downloadAndImmediateSwitchover (2),
the device will download the new
software from the configured host. After
the download is finished, the device will
automatically restart with the new
software. If
downloadAndDelayedSwitchover (3) is
specified, the new image is copied to the
device. When the tftpDateTime value is
matched, the device discontinues its
normal operation and does the software
switchover. After an automatic reset, it
starts with the new system software.
Setting downloadWithoutSwitchover (4)
initiates a download without switching
over to the new software. When the
device is not downloading, this object will
have a value of notDownloading(1).
1.3.6.1.4.1.231.7.2.7.2.1 sysSwitchoverState INTEGER RW The values readyForSwitchover (1) and
3 notReadyForSwitchover (2) indicate
whether the system is ready to be
switched over to the new software that
was downloaded to the shadow flash
area, or not. If it is not passible,
h150eShadowFlashState gives details
on the reason. Setting this object to
switchoverNow (3) causes the device to
switchover immediately to the new
software which was downloaded to the
shadow flash area before and restart the
system. initSwitchoverDelayed(4)
causes a delayed switchover.
deprecated
1.3.6.1.4.1.231.7.2.7.2.1 sysFirmwareVersion DisplayString RO Version number of the systems firmware.
4
1.3.6.1.4.1.231.7.2.7.2.1 sysHlbSymbolSubInfo DisplayString RO Contains an URL to detailed symbol
5 information in addition to the symbol
information contained in the common
MIB object deviceSymbolInfo.
1.3.6.1.4.1.231.7.2.7.2.1 sysHlbBranding DisplayString RO Contains the branding string of the
6 device.
1.3.6.1.4.1.231.7.2.7.3 monitoringGrouphlb20 Monitoring Group MIB

1.3.6.1.4.1.231.7.2.7.3.1 numberOfIdleMonTableEnt INTEGER RO Contains the number of idle/load
ries monitoring table entries.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.3.2 hlb20IdleMonTable SEQUENCE This table contains information about the
OF system idle/load time (scanned every 5
Hlb20IdleMon minutes) for the last 24 hours.
TableEntry
1.3.6.1.4.1.231.7.2.7.3.2 hlb20IdleMonTableEntry Hlb20IdleMon The idle/load monitoring table entries.
.1 TableEntry
1.3.6.1.4.1.231.7.2.7.3.2 idleIndex INTEGER RO Identification of an table entry.
.1.1
1.3.6.1.4.1.231.7.2.7.3.2 idleValue INTEGER RO The load level value.
.1.2
1.3.6.1.4.1.231.7.2.7.3.3 numberOfIdleLatestTableE INTEGER RO Contains the number of precision idle/

ntries load monitoring table entries.
1.3.6.1.4.1.231.7.2.7.3.4 hlb20IdleLatestTable SEQUENCE This table contains information about the
OF system idle/load time (scanned every
Hlb20IdleLate minute) for the last 10 minutes.
stTableEntry
1.3.6.1.4.1.231.7.2.7.3.4 hlb20IdleLatestTableEntry Hlb20IdleLate The precision idle/load monitoring table
.1 stTableEntry for the ten latest values.
1.3.6.1.4.1.231.7.2.7.3.4 idleLatestIndex INTEGER RO Identification of an table entry.
.1.1
1.3.6.1.4.1.231.7.2.7.3.4 idleLatestValue INTEGER RO Identification of an table value.
.1.2
1.3.6.1.4.1.231.7.2.7.3.5 numberOfIdleMonYellowAl INTEGER RO Contains the number of yellow load

arms monitoring alarms.
1.3.6.1.4.1.231.7.2.7.3.6 numberOfIdleMonRedAlar INTEGER RO Contains the number of red load
ms monitoring alarms.
1.3.6.1.4.1.231.7.2.7.3.7 flagIdleMonYellowAlarm INTEGER RO 1, if load monitoring is on yellow alert.
0 otherwise
1.3.6.1.4.1.231.7.2.7.3.8 flagIdleMonRedAlarm INTEGER RO 1, if load monitoring is on red alert.
0 otherwise
1.3.6.1.4.1.231.7.2.7.3.9 thresholdIdleMonYellowAl INTEGER RW idle threshold value for generation of
arm (0..100) yellow alert.
1.3.6.1.4.1.231.7.2.7.3.1 thresholdIdleMonRedAlar INTEGER RW idle threshold value for generation of red
0 m (0..100) alert.
1.3.6.1.4.1.231.7.2.7.3.1 idleMonHighWaterMark INTEGER RO contains the load peak level of the
1 device.
1.3.6.1.4.1.231.7.2.7.3.1 idleMonLastValue INTEGER RO contains the latest load monitoring value.
2
1.3.6.1.4.1.231.7.2.7.3.1 numberOfFreeMemBuffers INTEGER RO Contains the number of memory buffers
3 TableEntries table entries. Item available in newer rel.
1.1 devices
deprecated
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.3.1 freeMemBuffersTable SEQUENCE This table contains information about the
4 OF number of free memory buffers for the
FreeMemBuff different buffer sizes. Table available in
ersTableEntry newer rel. 1.1 devices
deprecated
1.3.6.1.4.1.231.7.2.7.3.1 freeMemBuffersTableEntry FreeMemBuff The free memory buffers of this device.
4.1 ersTableEntry deprecated
1.3.6.1.4.1.231.7.2.7.3.1 bufferIndex INTEGER RO Identification of an table entry.
4.1.1 deprecated
1.3.6.1.4.1.231.7.2.7.3.1 bufferType DisplayString RO The type/size of this buffer.
4.1.2 deprecated
1.3.6.1.4.1.231.7.2.7.3.1 numOfFreeBuffers INTEGER RO The number of free buffers of this type.
4.1.3 deprecated
1.3.6.1.4.1.231.7.2.7.3.1 loadBalanceMeasureContr INTEGER RW Measuring the load balance of the

5 ol processes of the device is controlled by
this object. Setting the object to active (2)
starts the measuring, inactive (1) stops it.
Item available in newer rel. 1.1 devices
1.3.6.1.4.1.231.7.2.7.3.1 numberOfLoadBalanceTab INTEGER RO Contains the number of load balance
6 leEntries measurement entries.
deprecated
1.3.6.1.4.1.231.7.2.7.3.1 loadBalanceTable SEQUENCE This table contains detailed information
7 OF about load balance of the different
LoadBalanceT processes of the device.
ableEntry deprecated
1.3.6.1.4.1.231.7.2.7.3.1 loadBalanceTableEntry LoadBalanceT The load balance for the processes of
7.1 ableEntry this device.
deprecated
1.3.6.1.4.1.231.7.2.7.3.1 loadBalanceIndex INTEGER RO Identification of an table entry.
7.1.1 deprecated
1.3.6.1.4.1.231.7.2.7.3.1 processDescription DisplayString RO Textual description of the process.
7.1.2 deprecated
1.3.6.1.4.1.231.7.2.7.3.1 loadProportionValue DisplayString RO Load proportion for every process.
7.1.3 deprecated
1.3.6.1.4.1.231.7.2.7.4 statisticsGrouphlb20 Statistics Group MIB

1.3.6.1.4.1.231.7.2.7.4.1 globalVcapiClientStatGrou global statistic data: vCAPI client
p
1.3.6.1.4.1.231.7.2.7.4.1 statVcapiInstalledClients INTEGER RO Contains the number of vCAPI Clients
.1 installed
deprecated
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.4.1 statVcapiLoggedInClients INTEGER RO Contains the total number of vCAPI
.2 Client logins since the last system
restart.
deprecated
1.3.6.1.4.1.231.7.2.7.4.1 statVcapiActiveClients INTEGER RO Contains the number of active vCAPI
.3 clients (or b-channels if channel bundling
is configured).
deprecated
1.3.6.1.4.1.231.7.2.7.4.2 globalH323ClientStatGrou global statistic data: H323 client

p
1.3.6.1.4.1.231.7.2.7.4.2 statH323InstalledClients INTEGER RO Contains the number of H323 Clients
.1 installed (which means they are
configured in the customer database)
deprecated
1.3.6.1.4.1.231.7.2.7.4.2 statH323ActiveClients INTEGER RO Contains the number of H323 Clients in
.2 an active connection state.
deprecated
1.3.6.1.4.1.231.7.2.7.4.3 globalTfaClientStatGroup global statistic data: TFA client

1.3.6.1.4.1.231.7.2.7.4.3 statTfaInstalledClients INTEGER RO Contains the number of TFA Clients
.1 installed (which means they are
configured in the customer database).
deprecated
1.3.6.1.4.1.231.7.2.7.4.3 statTfaActiveClients INTEGER RO Contains the number of TFA Clients in
.2 active connection state.
deprecated
1.3.6.1.4.1.231.7.2.7.4.3 statTfaRegistratedClients INTEGER RO Contains the number of TFA Clients that
.3 have registered themselves to their
hg3550 since the last system restart.
deprecated
1.3.6.1.4.1.231.7.2.7.4.3 statTfaClientLogonSucces INTEGER RO Contains the number of successful TFA
.4 s Clients logons since the last system
restart.
deprecated
1.3.6.1.4.1.231.7.2.7.4.3 statTfaClientLogonFailed INTEGER RO Contains the number of failed TFA
.5 Clients logons since the last system
restart.
deprecated
1.3.6.1.4.1.231.7.2.7.4.4 globalVoiceClientCallStatG global statistic call data for H323 and TFA
roup clients
1.3.6.1.4.1.231.7.2.7.4.4 statOutgoingRtp INTEGER RO Contains the number of outgoing RTP
.1 packets (H323 + TFA Clients).
1.3.6.1.4.1.231.7.2.7.4.4 statOutgoingLostRtp INTEGER RO Contains the number of outgoing RTP
.2 packets lost (H323 + TFA Clients).
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.4.4 statIncomingRtp INTEGER RO Contains the number of incoming RTP
.3 packets (H323 + TFA Clients).
1.3.6.1.4.1.231.7.2.7.4.4 statIncomingLostRtp INTEGER RO Contains the number of incoming RTP
.4 packets lost (H323 + TFA Clients).
1.3.6.1.4.1.231.7.2.7.4.4 statTotalBytesSentRtp INTEGER RO Contains the number of bytes sent
.5 (RTP).
1.3.6.1.4.1.231.7.2.7.4.4 statTotalBytesRecvRtp INTEGER RO Contains the number of bytes received
.6 (RTP).
1.3.6.1.4.1.231.7.2.7.4.5 indivVoiceClientCallStatBu individual statistic data: H323 client

ffer
1.3.6.1.4.1.231.7.2.7.4.5 numOfClientStatIndTableE INTEGER RO Contains the number of individual H323
.1 ntries client statistics table entries.
1.3.6.1.4.1.231.7.2.7.4.5 hlb20ClientStatIndTable SEQUENCE This table contains individual statistic
.1.2 OF information for every H323 client.
Hlb20ClientSt Usually, this table is empty. It is designed
atIndTableEntr for expert level debugging only.
y
1.3.6.1.4.1.231.7.2.7.4.5 hlb20ClientStatIndTableEn Hlb20ClientSt The individual H323 client statistic
.1.2.1 try atIndTableEntr information table entries.
y
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliIndex Hlb20ClientSt RO Identification of an table entry enabled by
.1.2.1.1 atIndSnmpInd this index.
ex
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliCallId OCTET RO Contains the call ID (canonial name) of
.1.2.1.2 STRING (SIZE the call target.
(1..21))
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliLocalIpAddr TransportLabe RO Contains the IP address of the local
.1.2.1.3 ess l endpoint.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliTimeBegin DateAndTime RO Contains the time stamp for the start of
.1.2.1.4 the call.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliTimeEnd DateAndTime RO Contains the time stamp for the end of
.1.2.1.5 the call.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliEncoder INTEGER RO Contains encoder information.
.1.2.1.6
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliDecoder INTEGER RO Contains decoder information.
.1.2.1.7
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliOutgoingRt INTEGER RO Contains the number of outgoing RTP
.1.2.1.8 p packets.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliOutgoingLo INTEGER RO Contains the number of outgoing RTP
.1.2.1.9 stRtp packets lost.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliIncomingRt INTEGER RO Contains the number of incoming RTP
.1.2.1.10 p packets.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliIncomingLo INTEGER RO Contains the number of incoming RTP
.1.2.1.11 stRtp packets lost.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliTotalBytesS INTEGER RO Contains the number of bytes sent.
.1.2.1.12 entRtp
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliTotalBytesR INTEGER RO Contains the number of bytes received.
.1.2.1.13 ecvRtp
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliDelay INTEGER RO Contains the average network delay.
.1.2.1.14
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliJitter INTEGER RO Contains the average jitter.
.1.2.1.15
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceConnectionCo OCTET RO Contains the conference ID (canonial
.1.2.1.16 nfId STRING (SIZE name) which is unique for all parties
(1..21)) involved in the call or conference.
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceConnectionQu INTEGER RO The overall quality of the call or call -
.1.2.1.17 ality section.
- normal(1)
- warning(2)
- minor(3)
- major(4)
- critical(5)
1.3.6.1.4.1.231.7.2.7.4.5 statIndVoiceCliRemoteIpA TransportLabe RO Contains the IP address of the remote
.1.2.1.18 ddress l endpoint.
1.3.6.1.4.1.231.7.2.7.4.5 voIPQualityNotificationCou INTEGER RO Total number of VoIP quality traps that

.3 nter were sent since agent start.
1.3.6.1.4.1.231.7.2.7.4.6 audioStreamStatGroup individual statistic data: H323 client

1.3.6.1.4.1.231.7.2.7.4.6 statAudioStreamSccRxErr INTEGER RO Contains the number of errors (buffer
.1 or underruns) in the communication
between the CPU and the receiving
DSP's. (Object not available in hg3550 /
Xpress @LAN 1.0)
deprecated
1.3.6.1.4.1.231.7.2.7.4.6 statAudioStreamSccTxErr INTEGER RO Contains the number of errors (buffer
.2 or overflows) in the communication
between the CPU and the sending
DSP's. (Object not available in HG1500 /
Xpress @LAN 1.0)
1.3.6.1.4.1.231.7.2.7.5 sendAlarmWithValues TRAP If an error occurs, there will be checked if

the errorClass is configured to trigger a
immediate signaling. If so, a trap will be
send to the management station
containing the information shown above.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.6 fileOverflowError TRAP Inform the manager that the trap history
table got too big. Unless the size of the
table is reduced by the manager (by
resetting numberOfTrapHistoryEntries),
the oldest trap informations will be
overridden from now on.
1.3.6.1.4.1.231.7.2.7.7 allServeGrouphlb20 HiPath AllServe Group MIB

1.3.6.1.4.1.231.7.2.7.7.1 registrationState INTEGER RO Contains information about the HiPath
AllServe registration state.
- registered(1)
- notRegistered(2)
1.3.6.1.4.1.231.7.2.7.7.2 numberOfCallAddrTableEn INTEGER RO Contains the number of call address
tries table entries.
1.3.6.1.4.1.231.7.2.7.7.3 numberOfCallAddrCacheE INTEGER RO Contains the number of call address
ntries cache entries.
1.3.6.1.4.1.231.7.2.7.7.4 numberOfNodeIpTableEntr INTEGER RO Contains the number of node IP table
ies entries.
1.3.6.1.4.1.231.7.2.7.7.5 hlb20NodeIpTable SEQUENCE This table contains information about the
OF assignment of IP addresses to HiPath
Hlb20NodeIpT AllServe nodes.
ableEntry
1.3.6.1.4.1.231.7.2.7.7.5 hlb20NodeIpTableEntry Hlb20NodeIpT The node IP table entries.
.1 ableEntry
1.3.6.1.4.1.231.7.2.7.7.5 nodeIndex INTEGER RO Identification of an table entry, identical to
.1.1 node id.
1.3.6.1.4.1.231.7.2.7.7.5 nodeIpNumOfIpAddr INTEGER RO Number of IP address entries for this
.1.2 node.
1.3.6.1.4.1.231.7.2.7.7.5 nodeIpAddresses DisplayString RO Assigned IP addresses for this node.
.1.3
1.3.6.1.4.1.231.7.2.7.7.6 numberOfNuPortDataTabl INTEGER RO Contains the number of networking unit

eEntries port data table entries.
1.3.6.1.4.1.231.7.2.7.7.7 hlb20NuPortDataTable SEQUENCE This table contains information about the
OF networking unit port data of this device.
Hlb20NuPortD
ataTableEntry
1.3.6.1.4.1.231.7.2.7.7.7 hlb20NuPortDataTableEntr Hlb20NuPortD The networking unit port data table
.1 y ataTableEntry entries.
1.3.6.1.4.1.231.7.2.7.7.7 nuPortDataIndex INTEGER RO Identification of an table entry.
.1.1
1.3.6.1.4.1.231.7.2.7.7.7 nuCardPort INTEGER RO The lw_port to the system.
.1.2
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.7.7 nuPortDataProtocol INTEGER RO The networking protocol.
.1.3
1.3.6.1.4.1.231.7.2.7.7.7 nuPortDataNumOfBchn INTEGER RO The amount of B-channels to the system.
.1.4
1.3.6.1.4.1.231.7.2.7.7.7 nuPortDataActiveBchn INTEGER RO The number of active B-channels.
.1.5
1.3.6.1.4.1.231.7.2.7.7.8 numberOfNuTransDataTa INTEGER RO Contains the number of networking unit

bleEntries transaction data table entries.
1.3.6.1.4.1.231.7.2.7.7.9 hlb20NuTransDataTable SEQUENCE This table contains information about the
OF networking unit transaction data of this
Hlb20NuTrans device.
DataTableEntr
y
1.3.6.1.4.1.231.7.2.7.7.9 hlb20NuTransDataTableE Hlb20NuTrans The networking unit transaction data
.1 ntry DataTableEntr table entries.
y
1.3.6.1.4.1.231.7.2.7.7.9 nuTransDataIndex INTEGER RO Identification of an table entry.
.1.1
1.3.6.1.4.1.231.7.2.7.7.9 nuTransStepState INTEGER RO The step table state.
.1.2
1.3.6.1.4.1.231.7.2.7.7.9 nuTransCallDirection INTEGER RO The call direction
.1.3 - incoming(1) = to mainboard
- outgoing(2) = from mainboard
1.3.6.1.4.1.231.7.2.7.7.9 nuTransCallRefSys INTEGER RO The call reference to the mainboard.
.1.4
1.3.6.1.4.1.231.7.2.7.7.9 nuTransBchnIndex INTEGER RO The channel index in the TSA message.
.1.5
1.3.6.1.4.1.231.7.2.7.7.9 nuTransTimeSlot INTEGER RO The timeslot on the PCM / IOM interface.
.1.6
1.3.6.1.4.1.231.7.2.7.7.9 nuTransPartnerIpAddr IpAddress RO The IP address of the HiPath AllServe
.1.7 partner node.
1.3.6.1.4.1.231.7.2.7.7.9 nuTransCallRefIp INTEGER RO The call reference to the IP network.
.1.8
1.3.6.1.4.1.231.7.2.7.8 ethernetStatGrouphlb20 Ethernet Statistics Group MIB

1.3.6.1.4.1.231.7.2.7.8.1 ethernetStatState INTEGER RW Initialize the ethernet statistics data to
zero by setting value 2.
- counting(1)
- reset(2)
1.3.6.1.4.1.231.7.2.7.8.2 goodFramesTransmitted INTEGER RO Successfully sent ethernet frames
1.3.6.1.4.1.231.7.2.7.8.3 goodFramesReceived INTEGER RO Correct received ethernet frames
1.3.6.1.4.1.231.7.2.7.8.4 sendRetries INTEGER RO successful ethernet send retries
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.8.5 receiveCollisions INTEGER RO Collisions on Ethernet
1.3.6.1.4.1.231.7.2.7.8.6 sendRetryError INTEGER RO 16 failed send attempts
1.3.6.1.4.1.231.7.2.7.8.7 macEngineDefer INTEGER RO MAC-Engine had to defer
1.3.6.1.4.1.231.7.2.7.8.8 excessiveDeferral INTEGER RO excessive deferral
1.3.6.1.4.1.231.7.2.7.8.9 lossOfCarrier INTEGER RO loss of carrier
1.3.6.1.4.1.231.7.2.7.8.1 lateCollision INTEGER RO late Collision
0
1.3.6.1.4.1.231.7.2.7.8.1 txBufferError INTEGER RO transmit buffer - fatal error
1
1.3.6.1.4.1.231.7.2.7.8.1 underflowError INTEGER RO underflow error - hardware error
2
1.3.6.1.4.1.231.7.2.7.8.1 checksumError INTEGER RO receive checksum error
3
1.3.6.1.4.1.231.7.2.7.8.1 framingError INTEGER RO receive framing error
4
1.3.6.1.4.1.231.7.2.7.8.1 missedFrames INTEGER RO missed frames
5
1.3.6.1.4.1.231.7.2.7.8.1 runtPackets INTEGER RO runt packets
6
1.3.6.1.4.1.231.7.2.7.8.1 frameTooShort INTEGER RO Received frame too short
7
1.3.6.1.4.1.231.7.2.7.8.1 frameTooLong INTEGER RO Received frame too long
8
1.3.6.1.4.1.231.7.2.7.8.1 bufferLimitReached INTEGER RO Low Buffer limit reached.
9
1.3.6.1.4.1.231.7.2.7.8.2 rcvBufferError INTEGER RO receive buffer - fatal error
0
1.3.6.1.4.1.231.7.2.7.8.2 overflowError INTEGER RO overflow error - hardware error
1
1.3.6.1.4.1.231.7.2.7.8.2 collisionErrorInt INTEGER RO transceiver test failed - hardware error
2
1.3.6.1.4.1.231.7.2.7.8.2 memoryErrorInt INTEGER RO system bus timeout - hardware error
3
1.3.6.1.4.1.231.7.2.7.8.2 excessiveInts INTEGER RO excessive interrupt occurance
4
1.3.6.1.4.1.231.7.2.7.8.2 linkChanged INTEGER RO link changed
5
1.3.6.1.4.1.231.7.2.7.8.2 linkMode INTEGER RO Operational mode of the ethernet link.
6 - halfDuplex10BaseT(1)
- halfDuplex100BaseT(3)
- fullDuplex10BaseT(2)
- fullDuplex100BaseT(4)
- auto(0)
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.8.2 good8021pFramesReceiv INTEGER RO The number of correct 802.1p frames
7 ed received.
1.3.6.1.4.1.231.7.2.7.8.2 babblingReceiveInts INTEGER RO The number of frames received with a
8 length that is greater than the maximum
allowed ethernet frame size (1518 or
1522 bytes).
1.3.6.1.4.1.231.7.2.7.8.2 babblingTransmitInts INTEGER RO The number of frames transmitted with a
9 length that is greater than the maximum
allowed ethernet frame size (1518 or
1522 bytes).
1.3.6.1.4.1.231.7.2.7.8.3 unexpectedInts INTEGER RO The number of unexpected interrupt
0 events that have occured. The presence
of such unexpected interrupts may
indicate a major problem on the device.
1.3.6.1.4.1.231.7.2.7.9 qosStatGrouphlb20 Quality Of Service Statistics Group MIB
1.3.6.1.4.1.231.7.2.7.9.1 numOfQosStatTableEntrie INTEGER RW Contains the number of entries in the

s quality of service (qos) statistics table.
The only valid write value is 0, which
resets all qos statistic counters.
1.3.6.1.4.1.231.7.2.7.9.2 qosStatTable SEQUENCE This table contains statistic information
OF for quality of service (QOS) mechanisms.
QosStatTable
Entry
1.3.6.1.4.1.231.7.2.7.9.2 qosStatTableEntry QosStatTable The QOS statistic information table
.1 Entry entries.
1.3.6.1.4.1.231.7.2.7.9.2 qosIndex INTEGER RO Identification of an table entry enabled by
.1.1 this index.
1.3.6.1.4.1.231.7.2.7.9.2 interface DisplayString RO The interface for which the QOS statistic
.1.2 data is collected.
1.3.6.1.4.1.231.7.2.7.9.2 remarkedFrames INTEGER RO The number of remarked frames.
.1.3
1.3.6.1.4.1.231.7.2.7.9.2 droppedPackets DisplayString RO The number of dropped packets for each
.1.4 queue.
1.3.6.1.4.1.231.7.2.7.10 bChannelStatGrouphlb20 B-Channel Statistics Group MIB
1.3.6.1.4.1.231.7.2.7.10. numOfBChannelStatTable INTEGER RW Contains the number of entries in the b-

1 Entries channel statistics table. The only valid
write value is 0, which resets all b-
channel counters.
1.3.6.1.4.1.231.7.2.7.10. bChannelStatTable SEQUENCE This table contains statistic information of
2 OF B-Channels.
BChannelStat
TableEntry
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.10. bChannelStatTableEntry BChannelStat The B-Channel statistic information table
2.1 TableEntry entries.
1.3.6.1.4.1.231.7.2.7.10. bChannelStatIndex INTEGER RO Identification of an table entry enabled by
2.1.1 this index.
1.3.6.1.4.1.231.7.2.7.10. bChannelIdentifier DisplayString RO The B-Channel identifier. 'Total' is the
2.1.2 (SIZE (0..255)) sum of all B-Channels.
1.3.6.1.4.1.231.7.2.7.10. frmLenViolation INTEGER RO Number of frames received with invalid
2.1.3 length.
1.3.6.1.4.1.231.7.2.7.10. nonOctetAligned INTEGER RO Number of frames with an invalid number
2.1.4 of bits.
1.3.6.1.4.1.231.7.2.7.10. rxAbortSequence INTEGER RO Number of times the HDLC abort
2.1.5 sequence was detected.
1.3.6.1.4.1.231.7.2.7.10. rxCrcError INTEGER RO Number of frames received with CRC
2.1.6 checksum errors.
1.3.6.1.4.1.231.7.2.7.10. qmcBusyInt INTEGER RO Number of frames received when no
2.1.7 receive buffer descriptor was available.
1.3.6.1.4.1.231.7.2.7.10. qmcMrfInt INTEGER RO Early indication for the number of frame
2.1.8 length violations.
1.3.6.1.4.1.231.7.2.7.10. qmcUnInt INTEGER RO Number of qmc transmitter underruns.
2.1.9
1.3.6.1.4.1.231.7.2.7.10. qmcIqov INTEGER RO Number of overruns in the qmx interrupt
2.1.10 ringbuffer.
1.3.6.1.4.1.231.7.2.7.10. qmcGunGov INTEGER RO This critical error leads to a reset. It
2.1.11 occurs when there's an buffer overrun in
the internal qmc fifo buffers.
1.3.6.1.4.1.231.7.2.7.10. numOfDspChannelsExistin INTEGER RO Contains the number of DSP channels

3 g physically existing.
1.3.6.1.4.1.231.7.2.7.10. numOfDspChannelsAvaila INTEGER RO Contains the number of DSP channels
4 ble available.
1.3.6.1.4.1.231.7.2.7.10. numOfDspChannelsInUse INTEGER RO Contains the number of DSP channels
5 actually used.
1.3.6.1.4.1.231.7.2.7.11 notificationGrouphlb20 Notification Group MIB containing trap

specifications
1.3.6.1.4.1.231.7.2.7.11. sendVoIPQualityNotificatio TRAP This notification will be sent when the
1 n latest voice over IP connection had
quality problems.
1.3.6.1.4.1.231.7.2.7.11. sendIpPhoneTableNotificat TRAP This notification will be sent whenever
2 ion the errorState of an IP phone table entry
changes or when the configuration of IP
phones is changed.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.12 ipPhoneGrouphlb20 IP Phone Group MIB
1.3.6.1.4.1.231.7.2.7.12. numOfIpPhoneTableEntrie INTEGER RO Contains the number of entries in the IP
1 s Phone table.
1.3.6.1.4.1.231.7.2.7.12. ipPhoneTable SEQUENCE This table contains information on all
2 OF configured OptiPoints and OptiCients,
IpPhoneTable but not standard H.323 phones.
Entry
1.3.6.1.4.1.231.7.2.7.12. ipPhoneTableEntry IpPhoneTable The IP Phone table entries.
2.1 Entry
1.3.6.1.4.1.231.7.2.7.12. ipPhoneIndex INTEGER RO Identification of an table entry enabled by
2.1.1 this index.
1.3.6.1.4.1.231.7.2.7.12. subscriberNumber DisplayString RO Subscriber call number which is
2.1.2 assigned to the phone.
1.3.6.1.4.1.231.7.2.7.12. ipAddress IpAddress RO Contains the IP address of the phone.
2.1.3
1.3.6.1.4.1.231.7.2.7.12. operationalState INTEGER RO Contains information about the
2.1.4 operational state of the phone.
- installed(1) means that the phone has
been configured in hg3550, but it is not
operational.
- registered(2) means that the phone is
operational.
- active(3) means that the phone is
actually in use.
1.3.6.1.4.1.231.7.2.7.12. errorState INTEGER RO Contains information about the error
2.1.5 state of the phone.
- normal(1)
- warning(2)
- minor(3)
- major(4)
- critical(5)
- unknown(6)
1.3.6.1.4.1.231.7.2.7.12. indexOfLastIpPhoneNotific INTEGER RO Contains the index of the last notification

3 ation trap that indicated configurational or
status changes in the IP phone table.
1.3.6.1.4.1.231.7.2.7.12. typeOfLastIpPhoneNotifica INTEGER RO Contains the type of the last notification
4 tion trap that indicated configurational or
status changes in the IP phone table.
1.3.6.1.4.1.231.7.2.7.12. subscriberNoOfLastIpPho DisplayString RO The subscriber number of the IP phone
5 neNotification involved.
1.3.6.1.4.1.231.7.2.7.12. ipAddressOfLastIpPhoneN IpAddress RO Contains the IP address of the IP phone
6 otification involved. If the IP address is 0.0.0.0, all
phones may be involved
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.12. errorStateOfLastIpPhoneN INTEGER RO Contains information about the error
7 otification state of the phone involved.
- normal(1)
- warning(2)
- minor(3)
- major(4)
- critical(5)
- unknown(6)
1.3.6.1.4.1.231.7.2.7.13 rg2500 RG2500 MIB

1.3.6.1.4.1.231.7.2.7.13. gwPlatformMib The Platform MIB for the company’s VoIP
1 Gateway.
See ar2500_platform.my
1.3.6.1.4.1.231.7.2.7.13. gwPlatformMibObjects
1.1
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHardwareGrou
1.1.1 p
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwConfigGrou The Hardware Configuration MIB
1.1.1.1 p
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModule INTEGER RO The Number of DSP modules fitted.
1.1.1.1.2 Count (0..12)
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwCpuType DisplayString RO The processor type.
1.1.1.1.3
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwCpuSpeed INTEGER RO The CPU speed in MHz.
1.1.1.1.4 (0..1024)
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwFlashMemo INTEGER RO The flash memory size in MB
1.1.1.1.5 ry (0..1024) (1024x1024 bytes).
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDram INTEGER RO The DRAM size in MB (1024x1024
1.1.1.1.6 (0..1024) bytes).
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspSlotCou INTEGER RO The number of DSP slots.
1.1.1.1.7 nt (0..12)
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwMacAddres OCTET RO The MAC address.
1.1.1.1.10 s STRING
(SIZE(6))
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwBootline DisplayString RO The bootline.
1.1.1.1.11
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwSystemSeri DisplayString RO The system serial number.
1.1.1.1.12 alNumber
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwMotherboar DisplayString RO The motherboard version.
1.1.1.1.13 dVersion
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwPartListVers DisplayString RO The part-list version.
1.1.1.1.14 ion
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwBootromVer DisplayString RO The boot ROM version.
1.1.1.1.15 sion
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModule SEQUENCE Table containing types of DSP modules
1.1.1.1.17 Table OF installed.
GwPlatformH
wDspModuleE
ntry
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModule GwPlatformH An entry in the DSP Module Table.
1.1.1.1.17.1 Entry wDspModuleE
ntry
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModuleI INTEGER RO The index into the dsp module table.
1.1.1.1.17.1.1 ndex (1..12)
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModule DisplayString RO The type indicator of the DSP module.
1.1.1.1.17.1.2 Type
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDspModule DisplayString RO The descriptive name of the dsp module,
1.1.1.1.17.1.3 Description e.g. The written part name, and type of
dsp, and size of RAM on the module.
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwResourceGr The Hardware Resources Group

1.1.1.3 oup
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwDramFree Unsigned32 RO The DRAM free in KBytes,
1.1.1.3.1 sysMemPart+safeMemPart
1.3.6.1.4.1.231.7.2.7.13. gwPlatformHwFlashFree Unsigned32 RO The Flash free, in KBytes.
1.1.1.3.2
1.3.6.1.4.1.231.7.2.7.13. gwPlatformSwConfigGrou The Software Configuration

1.1.2 p
1.3.6.1.4.1.231.7.2.7.13. gwPlatformSwBuild DisplayString RO The reported build identification of the
1.1.2.1 loaded software.
1.3.6.1.4.1.231.7.2.7.13. gwManagementMib The Management MIB for the company’s

2 RG 2500 Communication Gateway.
See ar2500_management.my
1.3.6.1.4.1.231.7.2.7.13. gwManagementMibObject
2.1 s
1.3.6.1.4.1.231.7.2.7.13. gwManagementMgmtGrou The Management Group
2.1.1 p
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro SEQUENCE The group of gateway property settings.
2.1.1.1 pertiesGroupTable OF
GwManageme
ntRouterPrope
rtiesGroupEntr
y
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro GwManageme The entry (row type) in the table of
2.1.1.1.1 pertiesGroupEntry ntRouterPrope gateway properties
rtiesGroupEntr settings.
y
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro GwManageme RO The index for the table of gateway
2.1.1.1.1.1 pertiesGroupIndex ntConfiguratio properties settings.
nGroupIndex
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro DisplayString RW Allows the name of the gateway to be
2.1.1.1.1.2 pertiesRouterName (SIZE(0..20) set.
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro DisplayString RW Allows the location of the gateway to be
2.1.1.1.1.3 pertiesRouterLocation (SIZE(0..20) set.
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro DisplayString RO IP address
2.1.1.1.1.4 pertiesIp (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. gwManagementRouterPro DisplayString RO Subnet mask
2.1.1.1.1.5 pertiesSubnetMask (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. gwManagementMgmtConfi The Management Configuration Group

2.1.1.3 gGroup
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon SEQUENCE The group of management SNMP
2.1.1.3.14 figTable OF settings.
GwManageme
ntCommConfi
gEntry
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon GwManageme The entry (row type) in the table of
2.1.1.3.14.1 figEntry ntCommConfi management SNMP configuration
gEntry settings.
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon GwManageme RO The index for the table of management
2.1.1.3.14.1.1 figIndex ntMgmtConfig SNMP configuration settings.
SnmpIndex
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon GwManageme RC This column holds the value which must
2.1.1.3.14.1.2 figSetting ntDisplayStrin be interpreted according to the type
g indicated by the preceeding column.
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon GwManageme RC The part of the setting which holds the IP-
2.1.1.3.14.1.3 figSettingIpAddr ntDisplayStrin Address.
g
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon GwManageme RC Type indicator for the data held in this row
2.1.1.3.14.1.4 figSettingType ntMgmtConfig of the table.
SnmpSettingT - readCommunity(1)
ype - writeCommunity(2)
- trapReceiver(3)
1.3.6.1.4.1.231.7.2.7.13. gwManagementCommCon RowCmd RC The row status for the table of
2.1.1.3.14.1.5 figStatus management SNMP configuration
settings.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout SEQUENCE The table of StaticRoute Configurations.
2.1.1.6 eConfigTable OF This table is used to configure the
GwManageme ipRouteTable at system start.
ntStaticRoute
ConfigEntry
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme The entry (row type) in the table of
2.1.1.6.1 eConfigEntry ntStaticRoute StaticRoute Configurations.
ConfigEntry
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme RO The index for the StaticRoute
2.1.1.6.1.1 eConfigIndex ntStaticRoute Configurations table.
ConfigIndex
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme RC The name by which the route will be
2.1.1.6.1.2 eConfigName ntNameDispla known to the manager.
yString
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme RC ipRouteDest from the ipRouteTable.
2.1.1.6.1.3 eDest ntAddressDisp
layString
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme RC ipRouteNextHop from the ipRouteTable.
2.1.1.6.1.4 eGateway ntAddressDisp
layString
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout GwManageme RC ipRouteMask from the ipRouteTable.
2.1.1.6.1.5 eMask ntAddressDisp
layString
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout INTEGER RC ipRouteAge from the ipRouteTable.
2.1.1.6.1.6 eTos
1.3.6.1.4.1.231.7.2.7.13. gwManagementStaticRout RowCmd RC The status of this static route entry.
2.1.1.6.1.7 eStatus
1.3.6.1.4.1.231.7.2.7.13. globalDataTable SEQUENCE Table containig global data of the rg2500

2.1.4 OF gateway.
GlobalDataEnt
ry
1.3.6.1.4.1.231.7.2.7.13. globalDataEntry GlobalDataEnt Entry in the global data table.
2.1.4.1 ry
1.3.6.1.4.1.231.7.2.7.13. globalDataID Integer32 RC Index to lookup an entry in the global
2.1.4.1.1 (0..1) data table.
1.3.6.1.4.1.231.7.2.7.13. systemLocation DisplayString RW
2.1.4.1.2 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. systemName DisplayString RW
2.1.4.1.3 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. systemIPAddress DisplayString RO
2.1.4.1.4 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. systemSubnetMask DisplayString RO
2.1.4.1.5 (SIZE(0..20))
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. systemDateTime DisplayString RW
2.1.4.1.6 (SIZE(14..20))
1.3.6.1.4.1.231.7.2.7.13. systemCountryCode Integer32 RW
2.1.4.1.7
1.3.6.1.4.1.231.7.2.7.13. systemUpTime TimeTicks RW
2.1.4.1.8
1.3.6.1.4.1.231.7.2.7.13. gwEnableGatekeeperUsa BooleanValue RW
2.1.4.1.9 ge
1.3.6.1.4.1.231.7.2.7.13. gwEnableSCNProtocolTun BooleanValue RW
2.1.4.1.10 neling
1.3.6.1.4.1.231.7.2.7.13. gwEnableH323TerminalSu BooleanValue RW
2.1.4.1.11 pport
1.3.6.1.4.1.231.7.2.7.13. gwEnablePreH450CallFor BooleanValue RW
2.1.4.1.12 ward
1.3.6.1.4.1.231.7.2.7.13. gwEnablePreH450CallTra BooleanValue RW
2.1.4.1.13 nsfer
1.3.6.1.4.1.231.7.2.7.13. gwEnableH450FeatureSu BooleanValue RW
2.1.4.1.14 pport
1.3.6.1.4.1.231.7.2.7.13. gwEnableH235Profile1Su BooleanValue RW
2.1.4.1.15 pport
1.3.6.1.4.1.231.7.2.7.13. urlOnlineHelp DisplayString RW
2.1.4.1.16 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. urlDocumentation DisplayString RW
2.1.4.1.17 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. serverSystemID DisplayString RW
2.1.4.1.18 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. serverIntegrOnOff BooleanValue RW
2.1.4.1.19
1.3.6.1.4.1.231.7.2.7.13. serverAuthIpAddress DisplayString RW
2.1.4.1.20 (SIZE(0..20))
1.3.6.1.4.1.231.7.2.7.13. serverAuthPort Integer32 RW
2.1.4.1.21
1.3.6.1.4.1.231.7.2.7.13. gwMSCandApplications HG3550 V2 / HiPath 4000 V2 MIB.

3 See cg2500.my
1.3.6.1.4.1.231.7.2.7.13. msc
3.1
1.3.6.1.4.1.231.7.2.7.13. mscStats
3.1.1
1.3.6.1.4.1.231.7.2.7.13. mscStatsOverall msc overall statistics
3.1.1.1
1.3.6.1.4.1.231.7.2.7.13. mscOutgoingRTPpackets Counter RO Outgoing RTP packets (overall).
3.1.1.1.1
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. mscOutgoingRTPLostpack Counter RO Outgoing RTP packets lost (overall).
3.1.1.1.2 ets
1.3.6.1.4.1.231.7.2.7.13. mscIncomingRTPpackets Counter RO Incoming RTP packets (overall).
3.1.1.1.3
1.3.6.1.4.1.231.7.2.7.13. mscIncomingRTPLostpack Counter RO Incoming RTP packets lost (overall).
3.1.1.1.4 ets
1.3.6.1.4.1.231.7.2.7.13. mscTotalBytesSent Counter RO Total bytes sent.
3.1.1.1.5
1.3.6.1.4.1.231.7.2.7.13. mscTotalBytesReceived Counter RO Total bytes received.
3.1.1.1.6
1.3.6.1.4.1.231.7.2.7.13. mscStatsPerCallTable SEQUENCE The table of per-call msc statistics.

3.1.1.2 OF
MscStatsPerC
allEntry
1.3.6.1.4.1.231.7.2.7.13. mscStatsPerCallEntry MscStatsPerC The Msc statistics about one resource.
3.1.1.2.1 allEntry
1.3.6.1.4.1.231.7.2.7.13. mscStatsPerCallInd INTEGER The table index
3.1.1.2.1.1
1.3.6.1.4.1.231.7.2.7.13. mscPeerCanonicalName OCTET RO The connection name of the number
3.1.1.2.1.2 STRING (SIZE called.
(0..64))
1.3.6.1.4.1.231.7.2.7.13. mscDestIP OCTET RO The destination IP address (H.323).
3.1.1.2.1.3 STRING (SIZE
(0..15))
1.3.6.1.4.1.231.7.2.7.13. mscBeginTime OCTET RO Time when the last call started.
3.1.1.2.1.4 STRING (SIZE
(0..64))
1.3.6.1.4.1.231.7.2.7.13. mscEncoder INTEGER RO Encoder used with this call.
3.1.1.2.1.5 - g711ULaw(0)
- g723(4)
- g711ALaw(8)
- g729(18)
1.3.6.1.4.1.231.7.2.7.13. mscDecoder INTEGER RO Decoder used with this call.
3.1.1.2.1.6 - g711ULaw(0)
- g723(4)
- g711ALaw(8)
- g729(18)
1.3.6.1.4.1.231.7.2.7.13. mscSpecOutgoingRTPpac Counter RO Outgoing RTP packets (per-call).
3.1.1.2.1.7 kets
1.3.6.1.4.1.231.7.2.7.13. mscSpecOutgoingRTPpac Counter RO Outgoing RTP packets lost (per-call).
3.1.1.2.1.8 ketsLost
1.3.6.1.4.1.231.7.2.7.13. mscSpecIncomingRTPpac Counter RO Incoming RTP packets (per-call).
3.1.1.2.1.9 kets
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. mscSpecIncomingRTPpac Counter RO Incoming RTP packets lost (per-call).
3.1.1.2.1.10 ketsLost
1.3.6.1.4.1.231.7.2.7.13. mscSpecBytesSent Counter RO Total bytes sent.
3.1.1.2.1.11
1.3.6.1.4.1.231.7.2.7.13. mscSpecBytesReceived Counter RO Total bytes received.
3.1.1.2.1.12
1.3.6.1.4.1.231.7.2.7.13. mscSpecRndTripNetwork Integer32 RO Round Trip Network Delay (in ms) for this
3.1.1.2.1.13 Delay connection.
1.3.6.1.4.1.231.7.2.7.13. mscSpecActualJitter Integer32 RO The actual jitter (in ms) for this
3.1.1.2.1.14 connection.
1.3.6.1.4.1.231.7.2.7.13. mscSpecJitterBufferDepth Integer32 RO Current size of the DSP jitter buffer (in
3.1.1.2.1.15 ms).
1.3.6.1.4.1.231.7.2.7.13. mscSpecRtpEncodings Integer32 RO Number of collected frames in one RTP
3.1.1.2.1.16 packet sent from this gateway.
1.3.6.1.4.1.231.7.2.7.13. mscSpecAverageNetwork Integer32 RO Average network delay for this call (in
3.1.1.2.1.17 Delay ms).
1.3.6.1.4.1.231.7.2.7.13. mscSpecJitterLan Integer32 RO Jitter in the LAN of this connection.
3.1.1.2.1.18
1.3.6.1.4.1.231.7.2.7.13. mscFractionLostOutgoing Integer32 RO Fraction of RTP data packets from a
3.1.1.2.1.19 specific source that were lost since the
previous receiver report was sent.
1.3.6.1.4.1.231.7.2.7.13. mscMaxFractionLostOutgo Integer32 RO Maximum fractional packet loss among
3.1.1.2.1.20 ing all currently participating session
members except ourself.
1.3.6.1.4.1.231.7.2.7.13. mscSpecCumLatePacketC Integer32 RO The number of late packets, since the
3.1.1.2.1.21 ount beginning of the connection.
1.3.6.1.4.1.231.7.2.7.13. mscEncTimePerPacket Integer32 RO Encoding time (in ms) per packet.
3.1.1.2.1.22
1.3.6.1.4.1.231.7.2.7.13. mscConfig Msc configuration

3.1.2
1.3.6.1.4.1.231.7.2.7.13. mscUdpPortLow INTEGER RW The low port boundary of RTP/RTCP
3.1.2.1 (1024..65535) ports.
1.3.6.1.4.1.231.7.2.7.13. mscUdpPortHigh INTEGER RW The high port boundary of RTP/RTCP
3.1.2.2 (1024..65535) ports.
1.3.6.1.4.1.231.7.2.7.13. mscTcpPortLow INTEGER RW The low port boundary of TCP ports
3.1.2.3 (1024..65535) (T38-fax).
1.3.6.1.4.1.231.7.2.7.13. mscTcpPortHigh INTEGER RW The high port boundary of TCP ports
3.1.2.4 (1024..65535) (T38-fax).
1.3.6.1.4.1.231.7.2.7.13. mscTrafficStatistic BooleanValue RW TrafficStatistic on / off; Generating of the
3.1.2.5 per call statistic (by the GW / GK) is
enabled or disabled.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. dspJitterBufferAdaptationE BooleanValue RW If this is set by host the DSP jitter buffer
3.1.2.9 nable adapts its depth based on its statistics. If
not, host has to explicitly adjust the jitter
buffer depth at run time, based on
statistics generated by the DSP.
1.3.6.1.4.1.231.7.2.7.13. mscJitterType INTEGER RW Jitter buffer adaptation algorithm (0..TIS,
3.1.2.10 1..HLB2)
1.3.6.1.4.1.231.7.2.7.13. mscJitterCacheUpdateInte INTEGER RW Jitter Cache update interval: 5 - 10
3.1.2.11 rval (5..10) seconds.
1.3.6.1.4.1.231.7.2.7.13. mscJitterTotalFractionLost INTEGER RW Factor for smoothing the varying fraction
3.1.2.15 Weight (0..1000) lost of incoming RTP packets caused by
jitter in 10th of percents, i.e. 1000 is
100.0%. Default: 300 (30%).
1.3.6.1.4.1.231.7.2.7.13. mscJitterMinFractionLost INTEGER RW Lower threshold for the adaptive control
3.1.2.16 (0..1000) of jitter buffer size for incoming RTP
packets in 10th of percents, i.e. 1000 is
100.0%. Default: 5 (0.5%).
1.3.6.1.4.1.231.7.2.7.13. mscJitterMaxFractionLost INTEGER RW Upper threshold for the adaptive control
3.1.2.17 (0..1000) of jitter buffer size for incoming RTP
packets in 10th of percents, i.e. 1000 is
100.0%. Default: 40 (4%).
1.3.6.1.4.1.231.7.2.7.13. mscJitterFactor INTEGER RW Factor for resizing the jitter buffer with
3.1.2.18 (0..1000) respect to the average jitter: Default: 4.
1.3.6.1.4.1.231.7.2.7.13. mscJitterIncrement INTEGER RW Increment of jitter buffer, if
3.1.2.19 (100..300) jitterMinFractionLost is exceeded in 100
microsecond steps: Default: 200 (20ms).
1.3.6.1.4.1.231.7.2.7.13. mscJitterDecrement INTEGER RW Decrement of jitter buffer, if smoothed
3.1.2.20 (100..300) average jitter falls below
jitterMaxFractionLost in 100
microsecond steps: Default: 100 (10ms).
1.3.6.1.4.1.231.7.2.7.13. mscJitterBufferAvarageDel INTEGER RW The depth of the jitter buffer in ms. Set by
3.1.2.21 ay (0..300) host at the configuration time. The DSP
will round the value to multiple of 10 ms.
Range: 0 - 300 ms
1.3.6.1.4.1.231.7.2.7.13. mscDspConfig Msc DSP configuration

3.1.3
1.3.6.1.4.1.231.7.2.7.13. mscVadEnable BooleanValue RW Voice Activity Detection on / off; VAD is
3.1.3.3 explicitly performed for G.711 only.
1.3.6.1.4.1.231.7.2.7.13. mscEchoCancellerEnable BooleanValue RW Echo Canceller on / off; Compensation
3.1.3.4 for echos which can occur in the case of
connection via the voice gateway to
analog telephones.
1.3.6.1.4.1.231.7.2.7.13. mscDtmfReceiveEnable BooleanValue RW Dtmf Outband Signalization on / off.
3.1.3.5
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. mscDtmfDefaultToneLengt INTEGER RW Default length of pulse of the DTMF
3.1.3.6 h (50..300) tones.
1.3.6.1.4.1.231.7.2.7.13. mscG711MaxRecvBytes INTEGER RW Max. Bytes of G711 coded RTP data.
3.1.3.7 (80..960)
1.3.6.1.4.1.231.7.2.7.13. mscG723MaxRecvBytes INTEGER RW Max. Bytes of G723A coded RTP data.
3.1.3.8 (24..96)
1.3.6.1.4.1.231.7.2.7.13. mscG729MaxRecvBytes INTEGER RW Max. Bytes of G729A/AB coded RTP
3.1.3.9 (20..120) data.
1.3.6.1.4.1.231.7.2.7.13. mscG711EncTimePerPack INTEGER RW Defines the encoding time (in ms) per
3.1.3.10 et (10..120) packet for G711 encoder control.
1.3.6.1.4.1.231.7.2.7.13. mscG723EncTimePerPac INTEGER RW Defines the encoding time (in ms) per
3.1.3.11 ket (30..120) packet for G723 encoder control.
1.3.6.1.4.1.231.7.2.7.13. mscG729EncTimePerPac INTEGER RW Defines the encoding time (in ms) per
3.1.3.12 ket (20..120) packet for G729 encoder control.
1.3.6.1.4.1.231.7.2.7.13. mscDtmfDefaultPauseLen INTEGER RW Default length of pause of the sent DMTF
3.1.3.13 gth (50..300) tones.
1.3.6.1.4.1.231.7.2.7.13. gwApplications
3.2
1.3.6.1.4.1.231.7.2.7.13. deviceConfiguration
3.2.1
1.3.6.1.4.1.231.7.2.7.13. deviceResourceStatistics
3.2.2
1.3.6.1.4.1.231.7.2.7.13. deviceResourceMgmtTabl SEQUENCE Device resource management statistics
3.2.2.1 e OF table
DeviceResour
ceMgmtEntry
1.3.6.1.4.1.231.7.2.7.13. deviceResourceMgmtEntr DeviceResour
3.2.2.1.1 y ceMgmtEntry
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. deviceId INTEGER RO unique id of a device
3.2.2.1.1.1 - devIdISDNSubs(0)
- devIdISDNTrunk(1)
- devIdHFA(2)
- devIdPayload(3)
- devIdMoH(4)
- devHXG3RTP(5)
- devHXG3Fax(6)
- devHXG3PPP(7)
- devHXG3Vcapi(8)
- devIdWAML(10)
- devIdISDNTrunk1(11)
- devIdDMC(15)
- devIdRTP(100)
- devIdFax(101)
- devIdPPP(102)
- devIdVcapi(103)
- devIdNu(104)
- devIdLegk(105)
- devIdUnused(106)
1.3.6.1.4.1.231.7.2.7.13. devMaxChannels Integer32 RO Effective max. number of useable
3.2.2.1.1.2 channels.
1.3.6.1.4.1.231.7.2.7.13. devSeizedChannels Integer32 RO Number of channels currently in use.
3.2.2.1.1.3
1.3.6.1.4.1.231.7.2.7.13. gwParameters Gateway Parameters

3.2.3
1.3.6.1.4.1.231.7.2.7.13. gwGlobalTrace
3.2.3.2
1.3.6.1.4.1.231.7.2.7.13. gwGlobalTraceID Integer32 RW
3.2.3.2.1
1.3.6.1.4.1.231.7.2.7.13. gwConsoleTraceOnOff BooleanValue RW Switch whole console tracing on or off.
3.2.3.2.2
1.3.6.1.4.1.231.7.2.7.13. gwFileTraceOnOff BooleanValue RW Switch whole file tracing on or off.
3.2.3.2.3
1.3.6.1.4.1.231.7.2.7.13. gwTraceMaxFileSize Integer32 RO Maximum size of trace file.
3.2.3.2.4
1.3.6.1.4.1.231.7.2.7.13. gwTraceTimerValue Integer32 RO Timer for tracing.
3.2.3.2.5
1.3.6.1.4.1.231.7.2.7.13. gwTraceMaxBuffSize Integer32 RO Maximum buffer size for tracing.
3.2.3.2.6
1.3.6.1.4.1.231.7.2.7.13. gwEventLog
3.2.3.4
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwTrapGenerationTbl SEQUENCE The trap generation table indicates for
3.2.3.4.1 OF which events traps are generated and for
GwTrapGener which not.
ationEntry
1.3.6.1.4.1.231.7.2.7.13. gwTrapGenerationEntry GwTrapGener An entry in the trap generation table for a
3.2.3.4.1.1 ationEntry particular event.
1.3.6.1.4.1.231.7.2.7.13. gwTrapEventID Integer32 RC This index of the trap generation table
3.2.3.4.1.1.1 identifies a particular event.
1.3.6.1.4.1.231.7.2.7.13. gwTrapEventName OCTET RC
3.2.3.4.1.1.2 STRING (SIZE
(0..64))
1.3.6.1.4.1.231.7.2.7.13. gwTrapType Integer32 RC This determines whether a trap is
3.2.3.4.1.1.3 generated for that event or not.
1.3.6.1.4.1.231.7.2.7.13. gwTrapFlag BooleanValue RC
3.2.3.4.1.1.4
1.3.6.1.4.1.231.7.2.7.13. gwRebootFlag BooleanValue RC
3.2.3.4.1.1.5
1.3.6.1.4.1.231.7.2.7.13. gwRebootType Integer32 RC This determines whether a trap is
3.2.3.4.1.1.6 generated for that event or not.
1.3.6.1.4.1.231.7.2.7.13. gwTrapGenRowCmd RowCmd RC Setting this to destroy will delete this
3.2.3.4.1.1.7 entry.
1.3.6.1.4.1.231.7.2.7.13. gwStatistics Gateway Statistics

3.2.5
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANVoiceCall Counter RO Number of incoming voice calls received
3.2.5.1 sRcvd1H in the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANVoiceCall Counter RO Number of incoming voice calls received
3.2.5.2 sRcvd24H in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANFaxCalls Counter RO Number of incoming fax calls received in
3.2.5.3 Rcvd1H the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANFaxCalls Counter RO Number of incoming fax calls received in
3.2.5.4 Rcvd24H the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANVoiceCall Counter RO Number of incoming voice calls
3.2.5.5 sConn1H connected in the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANVoiceCall Counter RO Number of incoming voice calls
3.2.5.6 sConn24H connected in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANFaxCalls Counter RO Number of incoming fax calls connected
3.2.5.7 Conn1H in the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANFaxCalls Counter RO Number of incoming fax calls connected
3.2.5.8 Conn24H in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXVoiceCall Counter RO Number of outgoing voice calls received
3.2.5.9 sRcvd1H in the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXVoiceCall Counter RO Number of outgoing voice calls received
3.2.5.10 sRcvd24H in the last 24 hours.
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXFaxCalls Counter RO Number of outgoing fax calls received in
3.2.5.11 Rcvd1H the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXFaxCalls Counter RO Number of outgoing fax calls received in
3.2.5.12 Rcvd24H the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXVoiceCall Counter RO Number of outgoing voice calls
3.2.5.13 sConn1H connected in the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXVoiceCall Counter RO Number of outgoing voice calls
3.2.5.14 sConn24H connected in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXFaxCalls Counter RO Number of outgoing fax calls connected
3.2.5.15 Conn1H in the last hour
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXFaxCalls Counter RO Number of outgoing fax calls connected
3.2.5.16 Conn24H in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsCumLANCallDurati Counter RO Cumulative call duration in seconds in
3.2.5.17 on1H the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsCumLANCallDurati Counter RO Cumulative call duration in seconds in
3.2.5.18 on24H the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsCumPBXCallDurat Counter RO Cumulative call duration in seconds in
3.2.5.19 ion1H the last hour.
1.3.6.1.4.1.231.7.2.7.13. gwStatsCumPBXCallDurat Counter RO Cumulative call duration in seconds in
3.2.5.20 ion24H the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumCurCalls Counter RO Cumulative number of current calls
3.2.5.25
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumLANDataCalls Counter RO Number of incoming LAN data calls
3.2.5.30 Rcvd1H received in the last hour.
3.2.5.31 Rcvd24H received in the last 24 hours.
3.2.5.32 Conn1H connected in the last hour.
3.2.5.33 Conn24H connected in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwStatsNumPBXDataCalls Counter RO Number of incoming PBX data calls
3.2.5.34 Rcvd1H received in the last hour.
3.2.5.35 Rcvd24H received in the last 24 hours.
3.2.5.36 Conn1H connected in the last hour.
3.2.5.37 Conn24H connected in the last 24 hours.
1.3.6.1.4.1.231.7.2.7.13. gwTrapGroup The HXG3 SNMP Traps

3.2.8
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. tisTrap TRAP Indicates a problem with the RG2500
3.2.8.1 software. Sent when the Admin server
detects a trapable event in the event log.
1.3.6.1.4.1.231.7.2.7.13. gwStartup TRAP Indicates the startup of HG3550 V2.
3.2.8.3
1.3.6.1.4.1.231.7.2.7.13. gwReboot TRAP Indicates the reboot of HG3550 V2.
3.2.8.4
1.3.6.1.4.1.231.7.2.7.13. gwThreshold TRAP Indicates that a threshold has reached in
3.2.8.5 HG3550 V2.
1.3.6.1.4.1.231.7.2.7.13. gwWanLinkUp TRAP Indicates a WAN Linkup of HG1500.
3.2.8.6
1.3.6.1.4.1.231.7.2.7.13. gwWanLinkDown TRAP Indicates a WAN Linkdown of HG3550
3.2.8.7 V2.
1.3.6.1.4.1.231.7.2.7.13. gwIpLinkUp TRAP Indicates an IP Link up of HG3550 V2.
3.2.8.8
1.3.6.1.4.1.231.7.2.7.13. gwIpLinkDown TRAP Indicates an IP Linkdown of HG3550 V2.
3.2.8.9
1.3.6.1.4.1.231.7.2.7.13. gwAuxTrap TRAP Indicates an auxiliary trap of HG3550 V2.
3.2.8.10
1.3.6.1.4.1.231.7.2.7.13. trapNum DisplayString RO Defines a software error number - use

3.2.9 with type of trap and info like software
component ID or board/port to isolate
exact error.
1.3.6.1.4.1.231.7.2.7.13. trapText DisplayString RO Defines text to be sent up with the trap.
3.2.10
1.3.6.1.4.1.231.7.2.7.13. trapType INTEGER RO The type of error occurred.
3.2.11 - software(1)
- hardware(2)
- startup(3)
- reboot(4)
- threshold(5)
- wanLinkUp(6)
- wanLinkDown(7)
- ipLinkUp(8)
- ipLinkDown(9)
- auxTrap(10)
1.3.6.1.4.1.231.7.2.7.13. gwtrapSeverity DisplayString RO Defines the severity of the trap.
3.2.12
Object-ID Object name Description

1.3.6.1.4.1.4329.2 iandcAdmin
Table 16 Definitions in the company’s specific MIB
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.4329.2.24 hg3550v11 Definition of the system OID for hg3550 V2
Table 16 Definitions in the company’s specific MIB

1.3.6.1.2.1.10.20.2.0.1 isdnMibCallInformation This trap/inform is sent to the manager under the following
condidions:
- on incoming calls for each call which is rejected for policy
reasons (e.g. unknown neighbor or access violation)
- on outgoing calls whenever a call attempt is determined to have
ultimately failed. In the event that call retry is active, then this will
be after all retry attempts have failed.
- whenever a call connects. In this case, the object
isdnBearerCallConnectTime should be included in the trap.
1.3.6.1.4.1.231.7.2.7.5 sendAlarmWithValues If an error occurs, there will be checked if the errorClass is

configured to trigger a immediate signaling. If so, a trap will be
send to the management station containing the information
shown above.
1.3.6.1.4.1.231.7.2.7.6 fileOverflowError Inform the manager that the trap history table got too big. Unless
the size of the table is reduced by the manager (by resetting
numberOfTrapHistoryEntries), the oldest trap informations will be
overridden from now on.
1.3.6.1.4.1.231.7.2.7.11.1 sendVoIPQualityNotification This notification will be sent when the latest voice over IP
connection had quality problems.
1.3.6.1.4.1.231.7.2.7.11.2 sendIpPhoneTableNotificati This notification will be sent whenever the errorState of an IP
on phone table entry changes or when the configuration of IP phones
is changed.
1.3.6.1.4.1.231.7.2.7.13. tisTrap Indicates a problem with the RG2500 software. Sent when the
3.2.8.1 Admin server detects a trapable event in the event log.
1.3.6.1.4.1.231.7.2.7.13. gwStartup Indicates the startup of HG3550 V2.

3.2.8.3
1.3.6.1.4.1.231.7.2.7.13. gwReboot Indicates the reboot of HG3550 V2.
3.2.8.4
1.3.6.1.4.1.231.7.2.7.13. gwThreshold Indicates that a threshold has reached in HG3550 V2.
3.2.8.5
1.3.6.1.4.1.231.7.2.7.13. gwWanLinkUp Indicates a WAN Linkup of HG1500.
3.2.8.6
1.3.6.1.4.1.231.7.2.7.13. gwWanLinkDown Indicates a WAN Linkdown of HG3550 V2.
3.2.8.7
1.3.6.1.4.1.231.7.2.7.13. gwIpLinkUp Indicates an IP Link up of HG3550 V2.
3.2.8.8
1.3.6.1.4.1.231.7.2.7.13. gwIpLinkDown Indicates an IP Linkdown of HG3550 V2.
3.2.8.9
Table 17 Collected list of traps (repeated)
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm

1.3.6.1.4.1.231.7.2.7.13. gwAuxTrap Indicates an auxiliary trap of HG3550 V2.
3.2.8.10
Table 17 Collected list of traps (repeated)
A31003-H3160-S104-8-7620, 07/2014
gateways_20_snmp.fm
A31003-H3160-S104-8-7620, 07/2014
gateways_21_ports.fm
IP Ports
General Information
21 IP Ports

The port assignments are available in the Interface Management Database
(IFMDB).
You can access the IFMDB via Intranet or Unify Partner Portal:
• Intranet
Homepage > Index “I” > IFMDB (Interface Management DataBase)
• Unify Partner Portal

Support > Interface Management (IFMDB)
21.2 Port Range
21.2.1 IP Trunking + DMC (IP Trunking and IPDA)

Master Connections
Port value range with AMO CGWB
The UDP port range is configured with the AMO CGWB for IP trunking master
connections and DMC slave connections where HG 3500 is a DMC endpoint (i.e.
for IP trunking or IPDA). The corresponding parameter is UDPPRTLO in the
TYP=ASC branch. UDPPRTHI can not be modified. It is calculated from the value
of UDPPRTLO + 999 Ports.
The standard value for UDPPRTLO is 29100.
IMPORTANT: Because connections can be switched with(out) DMC and/or SPE

(depending on the configuration), the maximum number of ports must always be
reserved by the gateway, even if possibly only a lower number of ports is used!
21.2.2 IPDA (HG 3575/HG 3500) + DMC (HG 3575)

master connections
• IPDA master connections
A31003-H3160-S104-8-7620, 07/2014
IP Ports
Information for Network Administrators
The UDPPORT parameter in the AMO SIPCO is used for the payload stream
in the IPDA master connection, i.e. for connections between the IPDA-HG
3500 and the HG 3575 and vice versa and for connections from HG 3575 to
HG 3575.
For IPDA master connections, only the start value is defined in the AMO
SIPCO, TYPE=DIFFSERV, UDPPORT=<4352 ... 65083>. The upper value
(=maximum number of ports actually used) is calculated on the basis of the
number of B channels of the board used.
The port with the lowest value can be set to even values in the range [4352
... 65280].
• DMC slave connections

The UDPPORT parameter applies to the AMO SIPCO for DMC slave
connections where NCUI2+/NCUI4 is the DMC endpoint. The following ports
are used automatically.
The port range from the AMO CGWB (UDPPRTLO-UDPPRTHI) applies to
slave connections where STMI2/STMI4 is the DMC endpoint.
IMPORTANT: The ports in use cannot be modified with the exception of ports for
"UDP-Payload".
21.3 Information for Network Administrators
IMPORTANT: IP packets with the used ports (hard-coded and configured using
AMOs) must be routed transparently in the IP network, i.e. the packets must be
unmanipulated, e.g. by a firewall). Functional problems can be the result of non-
transarent routing!
21.4 Examples
The following are a few examples to clarify the traffic restrictions applied to certain
ports.
A31003-H3160-S104-8-7620, 07/2014
IP Ports
Examples
21.4.1 Payload
Depending on the board in use (HG 3500 or HG 3575), ports used are taken from
a certain port range defined by the parameter UDPPORT (AMO SIPCO). The port
range for RTP/RTCP is defined by the following interval: [UDPPORT ..
UDPPORT + 960].
Port 4007 is used for a path test in the case of poor payload quality. See Section
2.9.1, “When is Payload Survivability Used?” in the document "IP Distributed
Architecture (IPDA)" - keyword "UDP-PINA".
HG Peripheral
HG 4352 .. 45999
59 3575 Boards
.. 4
4352 .. 4599
3500
5 2 AP 17
43 uses ports 4352 .. 4599
HG 43
3500 43 52
52 ..
.. 4 45
59 99
9
Control
CC-A/ HG Peripheral
CC-B 3575 Boards
HiPath AP 35
4000
uses ports 4352 .. 4599
in addition port 4007 must be available
port 4007 can be used
Figure 22 Example: Port usage for payload
21.4.2 Signaling
The term signaling refers to the entire data exchange between CC and access
point. This includes loading and controlling peripheral boards, security
messages, routine tests and naturally, all call processing messages including
telephone display texts.
Every access point, that is, every HG 3575, has a signaling connection to the
active CC.
The connection for this is always set up by the CM. The source port alternates
between 1124 and 1125. The destination port (ASC HG 3575) is 4000.
The HG 3575 loadware is loaded over FTP. The HG 3575 logs on to the CM’s FTP
server for this. The FTP server grants read-only access to the HG 3575
configured and allows only one download at a time.
If signaling survivability is configured additional connections are used.
The supervisory connection monitors the principal availability of the path from the
CM to the HG 3575 in the IP network - in parallel to the signaling connection.
The connection for this is always set up by the CC. The source port alternates
A31003-H3160-S104-8-7620, 07/2014
IP Ports
Examples
If the supervisory connection is interrupted, the signaling connection is re-routed

over a PSTN router and modem. The signaling connection’s IP address and ports
are retained.
The modem-based availability of a HG 3575 with signaling survivability is

cyclically tested in normal mode. 
The connection for this is always set up by the CM. The source port alternates
IMPORTANT: For SURVPATH test:

There will be an ARP request from active CC (physical linux address from V6) for
the MAC of the WAML. Afterwards packets will be routed on port 4002 to the
WAML using the IP Address of the NCUI on the WAML MAC.

For normal Signalling Survivability:
Normal signalling happens on port 4000. Once the keep alive fails for the super-
visory port 4001, there will be an ARP request from active CC (physical linux
address from V6) for the MAC of the WAML.
Afterwards packets will be instantly routed on port 4000 to the WAML using the
IP address of the NCUI but the WAML MAC on same TCP session, i.e. TCP
session is not re-established, only the destination MAC address is replaced by
the WAML MAC.
HG Peripheral
a re 3575 Boards
w AP 17
g ad
HG alin 75 lo
n 35
3500 sig
0 00 e HG
4 th
HG 5 <-> ding
2 a
3500 11 Lo
4 or FTP
2 20
11 00 signal ing
1124 or 11 25 <-> 40 40 01 monitoring
*) HG Peripheral
11 27 <- > war e
3575
Control 1126 or th e H G 3575 lo ad Boards
CC-A/ FTP Lo ad in g AP 35
20
CC-B ISDN 1124 or 1125 <-> 4000 signaling **) Modem
HiPath Router 1128 or 1129 <-> 4002 modem test *)
4000 20 FTP Loading the HG 3575 loadware **)
*) Only if signaling survivability is configured
**) Only if signaling supervisory is active
Figure 23 Example: Port usage for signaling
A31003-H3160-S104-8-7620, 07/2014
IP Ports
Examples
21.4.3 SNMP
The gateways HG 3500 and HG 3575 come with an SNMP agent which provides
read-only access to MIB-2 data and a gateway-specific MIB. Please refer to
Chapter 20, “SNMP Support HG 3500 / HG 3575”. Read-only access is
supported. No parameters may be changed. No traps are transferred.
The SNMP agent waits by default at port 161.
HG Peripheral
HG 3575 Boards
3500
AP 17
HG
3500
Control Port 161

CC-A/CC-B
HG Peripheral
3575 Boards
HiPath
AP 35
4000
SNMP Manager
MIB Browser
Figure 24 Example: Port usage for SNMP access
21.4.4 Diagnostics
Additional services that are normally inaccessible (ports blocked) can be
activated on the gateways HG 3500 and HG 3575 for fault diagnosis.
These are
SSH Port 22 TCP

HTTPS/WBM: Port 443 Web server for accessing diagnostic data
Logons with passwords can be configured to protect access for the HG 3575. HG
3500 uses fixed values for this.
A31003-H3160-S104-8-7620, 07/2014
IP Ports
Examples
HG Peripheral
HG 3575 Boards
3500
AP 17
HG
3500 Port 443 (HTTPS/WBM:)
Port 22 (SSH)
Control
CC-A/CC-B
HG Peripheral
3575 Boards
HiPath
AP 35
4000
PC
Figure 25 Example: Port usage for diagnosis
A31003-H3160-S104-8-7620, 07/2014
gateways_22_wbm.fm
WBMs of the Boards
22 WBMs of the Boards

For a description of the graphical user interface of the WBMs of HG 3500 and HG
3575 please refre to the following link:
http://apps.g-dms.com:8081/techdoc/en/P31003H3160M1000176A9/index.htm
A31003-H3160-S104-8-7620, 07/2014
gateways_22_wbm.fm
WBMs of the Boards
A31003-H3160-S104-8-7620, 07/2014
gateways_23_diagnosis.fm
HG 3500 / HG 3575 Diagnostic Options
23 HG 3500 / HG 3575 Diagnostic Options

All diagnostic options for the gateways HG 3500 and HG 3575 are part of the
WBM. The trace components can be configured in WBM. More information is
provided in the WBM online help.
• Retrieving/deleting an event protocol in the True Flash File System (TFFS)

via WBM
Maintenance -> Events -> Event Log -> Load via HTTP
Maintenance -> Events -> Event Log -> Clear Event Log
• Retrieving/deleting a trace protocol in the True Flash File System (TFFS) via
WBM
Maintenance -> Traces -> Trace Log -> Load via HTTP
Maintenance -> Traces -> Trace Log -> Clear Trace Log
• Retrieving/deleting a customer trace protocol in the True Flash File System

(TFFS) via WBM.
Maintenance -> Traces -> Customer Trace Log -> Load via HTTP
Maintenance -> Traces -> Customer Trace Log -> Clear Trace Log
• V24 trace / console trace
• LAN trace for XTracer client
• Service center
• In the event of a system crash, the DDC log must be retrieved via WBM.
• Retrieving busy resources
A31003-H3160-S104-8-7620, 07/2014
gateways_23_diagnosis.fm
HG 3500 / HG 3575 Diagnostic Options
A31003-H3160-S104-8-7620, 07/2014
gateways_24_faq.fm
Frequently asked Questions
24 Frequently asked Questions

1. Question: Are HG 3500 gateways supported on the Hicom 300 H?
Answer: No. Customers have to upgrade to HiPath 4000 V4 or higher in
order to take advantage of integrated IP gateways.
2. Question: Why does the HG 3500 require a static IP address?

Answer: From an IP networking point of view the HG 3500 is a gateway/
voice-router. Gateways/routers always require static IP addresses. This
ensures that all IP devices always find their gateway/router without having to
be reprogrammed constantly. Having dynamic IP addresses on gateways/
routers does not make any practical sense.
3. Question: Is the HG 3500 supported on IP distributed Access Points?

Answer: Yes. The HG 3500 version is supported on IP distributed Access
Points. Excessive delays that resulted from multiple TDM to IP conversions
when IP users on the IP Access Points call IP users on other IP Access Points
or IP users on the host are eliminated using DMCs.
4. Question: Why do HG 3500 and HG 3575 not support DHCP?

Answer: Consider HG 3500/3575 as a voice router. These voice routers
must always be available and know each other.
As is the case with IP router ports, it is useful to work with fixed IP addresses.
For complete system availability, it is also better to avoid dependencies on
DHCP and/or DNS servers.
5. Question: Why does the HG 3500 not support the G.722 codec?
Answer: There is absolutely no need for the HG 3500 to support G.722
because there is no wideband quality available on the TDM side; G.722
strictly works between IP clients and it is the clients that negotiate the codec
type. The HG 3500 will pass the signaling between any IP clients that support
G.722, enabling high quality voice.
6. Question: Why is the default value for the jitter buffer set to 60 milliseconds
on HG 3500/75? Can lower values also be set without leading to problems?
Answer: The default setting should ensure that initial startup runs relatively
smoothly. 60 ms is definitely too high for modern campus LAN installations
that only use device connections at Layer-2 switch ports and have sufficient
bandwidth reserves. A jitter buffer depth of 20 ms has been shown to be
satisfactory. 
On the other hand, 60 ms may sometimes be too low for installations over
WAN links with extremely low bandwidth and no reserve.
Setting the jitter buffer depth too high causes an unnecessarily high voice
delay. Setting it too low leads to poor transmission quality as a result of high
packet loss rates. This poses problems particularly for fax, modem, and ISDN
data connections.
A31003-H3160-S104-8-7620, 07/2014
gateways_24_faq.fm
7. Question: The maximum value that can be set for the jitter buffer is 210 ms.
I assume that the system works properly with this setting. Can I specify this
value in my WAN tender specification as a carrier requirement?
Answer: The system has no problems with a 210 ms jitter buffer. This setting
can balance out an extremely high jitter value of up to 210 ms without
impairing voice comprehension. It should be noted, however, that the size of
the jitter buffer has a direct effect on voice delay. See also Section 2.4, “Voice
Quality”. Voice delay (mouth-to-ear delay) is influenced by five elements:
• Packet size/sample size/the number of audio milliseconds per packet
• Processing time on the receiving end
• Transmission time in the LAN/WAN
• Jitter buffer
• Processing time on the receiving end

Figure 3 Voice quality depending on delay illustrates user satisfaction in
relation to the mouth-to-ear delay. Satisfaction drops dramatically at around
150 ms. Users start to notice interference at around 250 ms and become
dissatisfied.
Please note that a similar installation can also cause delays in trunk calls at
the other end of the CO trunk. In other words, only one half of the tolerable
delays may be caused by each end.
The following table shows a couple of sample calculations (all values in ms)
Sample size 20 60 20 20 60 60 60 20
Transmission time in the LAN/ 10 10 10 40 40 40 60 0
WAN
Processing time 32 32 32 32 32 32 32 32
Send+receive direction
Jitter buffer 20 20 60 60 60 120 210 210
Mouth-to-ear delay 82 122 122 152 192 252 362 262
It is not possible to achieve delays under 262 ms with a 210 ms jitter buffer.
8. Question: Both the HG 3500 and the HG 3575 have a fixed MAC address for
the Ethernet port assigned to the board. The IP addresses, however, are
assigned from the system database on the basis of the board’s “PEN“. If I
switch a HG 3500 in a particular slot with another board of the same type, the
IP address is maintained from the IP network’s perspective. However, the
MAC address to which the packets are sent changes. Doesn’t this mean that
the new board cannot be reached on account of the modified MAC address
until aging makes the ARP entries obsolete in the IP stacks?
A31003-H3160-S104-8-7620, 07/2014
gateways_24_faq.fm
Answer: The standard solution for this problem which is principally an

address resolution issue is also implemented on the HG 3500 and HG 3575
gateways. After activating the hardware interface, the gateway sends an ARP
request “gratuitous ARP“ to the actual IP address. This way, all IP devices on
the LAN segment learn the new IP <-> MAC address assignment.
9. Question: We regularly encounter statistic overflow problems in a customer

installation. Individual HG 3500/75 boards are temporarily taken out of
service. This clears down all calls over these boards but does not have any
other visible effect. What causes this problem and what can be done about it?
Answer: A statistical evaluation of error messages is performed for the HG
3500/75 in the same way as for other boards. This also includes the loss of
the signaling connection in HG 3575 and “bad quality“ messages for the HG
3500/75 payload connections.
Poor IP connection quality between the HG 3500/75 gateways or the HiPath
4000 central system and the HG 3575 over a sustained period can lead to a
large number of error messages in a short space of time, which in the end
causes a statistic overflow and a board reset.
Resetting the board should prevent a temporary board fault from turning into
a problem.
If the fault clearly originates in the network, no improvements will be achieved
by resetting the board.
You can use the AMO PSTAT to increase the threshold values for the STMI
and NCUI counters or deactivate the statistical evaluation entirely by setting
the threshold values to zero.
CHANGE-PSTAT:TYPE=CTRLTAB,LEVEL=BOARD,BOARD=NCUI,FAULT=1
or 2,
MAXCOUNT=xxx;
Stage 1 (COUNT1, counts pairs of in-service and out-of-service messages)
and stage 2 (COUNT2, counts messages that could develop into a message
flood) should also be taken into consideration.
Separate counters are used for NCUI/STMI and NCUI2/STMI2
+----------+--------+----------+----------+----------+----------+----------+
! NCUI ! COUNT1 ! Byte1 ! 61 ! 10 ! 2 ! 4 !
! STMI +--------+----------+----------+----------+----------+----------+
! ! COUNT2 ! Byte2 ! 61 ! 6 ! 2 ! 2 !
! +--------+----------+----------+----------+----------+----------+
! ! COUNT3 ! Byte3 ! 21 ! 10 ! 2 ! 4 !
! +--------+----------+----------+----------+----------+----------+
! ! COUNT4 ! Byte4 ! 19 ! 10 ! 2 ! 4 !
+----------+--------+----------+----------+----------+----------+----------+
! NCUI2 ! COUNT1 ! BYTE1 ! 241 ! 10 ! 2 ! 4 !
! STMI2 +--------+----------+----------+----------+----------+----------+
! ! COUNT2 ! Byte2 ! 241 ! 6 ! 2 ! 2 !
! +--------+----------+----------+----------+----------+----------+
! ! COUNT3 ! Byte3 ! 21 ! 10 ! 2 ! 4 !
! +--------+----------+----------+----------+----------+----------+
A31003-H3160-S104-8-7620, 07/2014
gateways_24_faq.fm
! ! COUNT4 ! Byte4 ! 19 ! 10 ! 2 ! 4 !
+----------+--------+----------+----------+----------+----------+----------+
Details on the AMO PSTAT can be found in the AMO description in the HiPath
4000 Service Manual.
Modifying the statistics prevents the boards from being reset when quality
problems that affect the overall function of the system occur in the IP network.
Your objective must be get these problems under control.
10. Question: Where can I hear how packet loss concealment affects the G.711
or G.729 codec?
The suggestion to provide acoustic samples in the electronic version of the
handbook was rejected by Service and Sales because this information is not
relevant for service technicians and sales managers. Sorry!
11. Question: Which is the difference between TOSLAN, TOSSIGNL and

TOSPL?
AMO SIPCO
TOSSIGNL QoS value for the TCP stream from HSR --> NCUIs
TOSPL QoS value for the payload stream outgoing from the IPDA-STMI (HHS)
AMO STMIB
TOSLAN QoS value for the TCP stream from NCUI --> HSR
TOSPL QoS value for the payload stream outgoing from the NCUI
AMO CGWB
TOSSIGNL QoS value for the TCP stream from STMI --> STMI (IP Trunking) or
STMI --> IP-Phone
TOSPL QoS value for the payload stream outgoing from the STMI (HFA/IP
Trunking)
Notes:
a) If MFS is used with IPDA functionality then the TOSPL (AMO SIPCO &
AMO CWGB) must be the same.
b) The TOS values for the packets sent by the IP phone can be setup in the
IP phone only.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
HiPath 4000 SoftGate
1 Overview
1.1 Functional Overview
Figure 1 Topology
The HiPath 4000 SoftGate provides cost-effective branch offices with reliable
HiPath 4000 survivability options and an easy IT integration in the HiPath 4000
solution and management suite. This software application offers full HiPath
Feature Access (HFA) for IP Endpoints, SIP Service Provider connectivity and
native SIP connectivity for trunking and subscriber with basic feature set based
upon a standard x86 server with Linux.
Any HiPath 4000 SoftGate site integrates seamless in the communication system
and network like an IPDA Access Point (AP 3700 IP) - in terms of features and
administration.
With this application customers can reduce capital cost (CAPEX) plus operational
cost (OPEX) and deploy centralized applications with uniform user experience.
1.2 Variants
HiPath 4000 SoftGate is available in three versions:
• HiPath 4000 SoftGate 50

Up to 50 ports for IP subscribers (HFA and SIP subscribers) or SIP trunking
(native SIP / SIP-Q).
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Features
(native SIP / SIP-Q).

(native SIP / SIP-Q)/a maximum number of 256 active ports.
1.3 Features
HiPath 4000 SoftGate offers the following features:
• Runs on standard server hardware.
• Operated with the Suse Linux Enterprise Server (SLES) operating system.
• Integrated media server.
• Administration via HiPath 4000 Assistant/Manager.
• Integration in HiPath 4000 networks.
• Supports all functions of IP Distributed Architecture (IPDA) (see Chapter 1,

“IPDA Feature Description”).
– Supports HiPath 4000 IPDA survivability options: signaling survivability

and connection to existing AP emergency servers.
– Supports a/µ law conversion per HiPath 4000 SoftGate. For more
information on a/µ law conversion please refer to the service manual
“HiPath 4000 V6, Section 4- IP Solutions > IP Distributed
Architecture”.
• Each HiPath 4000 SoftGate has the following sources available:
• 64 TSLs for conference
• 32 receivers for DTMF signaling (CR)
• 32 sender for DTMF signaling (CS)
• 2 continuous-tone dial tone receivers (DTR-DT)
• 2 cadenced-tone dial tone receivers (DTR-TT)
• 2 test receivers (TESTR)
• 1 test sender (TESTS)
• up to 18 different tones and 6 different announcements (for a detailed

description please refer to IP Distributed Architecture > Section 2.16,
“Different Announcements, Tones and DTMF DialTone Receivers
per Access Point”.)
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Features
• 1 music on hold
• 1 TDS port
• Maximum number of parallel calls: 250
• Supports DMC - as of HiPath 4000 V6 R1 the HiPath 4000 SoftGate is DMC

endpoint (see “Payload Switching DMC”, Chapter 4, “Direct Media Connect
(DMC) in Connection with HiPath 4000 SoftGate”).
• Supports T.38 Fax (see T.38 Fax).
• Supports signaling and payload encryption

More information about “Signaling and Payload Encryption (SPE)” can be
found in the respective section.
• Supports ISDN calls in the public network. PSTN connections are conducted
via Mediatrix SIP gateways.
• Analogue and fax connection
– via AP 3700 in conjunction with HiPath 4000 SoftGate 1000.
– via Mediatrix 41xx SIP gateway in conjunction with HiPath 4000 SoftGate
50 (see Section 3.3.5, “Analog Stations (Mediatrix 41xx)”).
• S0 connection via Mediatrix 44xx SIP gateways:
– S0 subscriber: Section 3.3.1, “ISDN (S0) Subscriber (Mediatrix 44xx)”
– S0 trunking: Section 3.3.2, “S0 Trunking (Mediatrix 44xx)”
– S0 data connection: Section 3.3.3, “ISDN (S0) Data Connections

(Mediatrix 44xx)”
• Mediatrix 35xx for PRI interface for T1.
• Mediatrix 36xx for PRI interface (see Section 3.3.4, “S2 Interface (Mediatrix
36xx)”) for E1.
• Mediatrix 1204 for analog trunking (see Section 3.3.6, “Analog Trunking
(Mediatrix 1204)”).
• Video integration with LifeSize terminals (see Chapter 5, “Video Connec-

tions”).
• Supports native SIP and SIP-Q trunking.
• IPv6 for SIP-Q and native SIP trunking with HiPath 4000 Softgate (see
Chapter 11, “IPv6”).
• End-to-end payload connections between native SIP trunks and SIP stations.
• Native SIP trunking enhancements:
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
LAN Interfaces
– configurable voice codecs for HG 3500 per destination gateway or IP sub

network
– native SIP trunking features: message waiting indication, call transfer and
call forwarding
• SIP service provider connections are possible.
NOTE: The firewall and SBC (session border control) configuration is

dependent on the customer network and NAT (network address translation).
• HiPath Cordless IP V1 has been released for connection to the HiPath 4000
SoftGate (see HiPath Cordless IP).
• For increased resilience, HiPath 4000 SoftGate can be connected with two
LAN cables to different switches/router (see Chapter 6, “LAN Redundancy”).
• Gatekeeper Redundancy for HFA Subscriber (see Chapter 9, “Gatekeeper

Redundancy for HFA Subscriber”).
• Survivable HiPath 4000 SoftGate (see Chapter 10, “Survivable HiPath 4000
SoftGate”).
• SIP Load balancing for inbound native SIP trunks. With load balancing the
system is to be able to scale the performance of involved SIP servers, to
avoid overloading of the server and to achieve high availability of the SIP
services (see Chapter 12, “Load Balancing”).
• As of HiPath 4000 V6 R1 HiPath Access modules can be connected directly

to the HiPath 4000 SoftGate. For information on licensing see HiPath Access
service documentation.
• With the release of HiPath Access the vNCUI can act as (secure) DMC
endpoint (as of HiPath 4000 V6 R1).
• As of HiPath 4000 V6 R2 QDC is supported.
• Preparation of HiPath Cordless E Integration as of HiPath 4000 V6 R2 (see

Chapter 16, “HiPath Cordless E Integration”).
• MFC-R2 support (see Chapter 15, “MFC-R2”).
• 9 peripheral slots for virtual boards and HiPath Access modules
1.4 LAN Interfaces

The HiPath 4000 SoftGate offers the following LAN interfaces:
• IPDA LAN
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Ports
For connecting to the HiPath 4000 host system.
• Management LAN
The feature "Separate LAN Connectivity for Administration and Voice Over
IP" is supported as of HiPath 4000 V6. The Voice LAN can now be split fully
from the Management LAN.
• WAN
The HiPath 4000 SoftGate offers a WAN interface to the Internet as of HiPath
4000 V6 R2.
You can find a scenario using the WAN interface of the HiPath 4000 SoftGate
in Chapter 13, “Secure Remote Subscriber”.
A LAN interface for signaling survivability is supported as of HiPath 4000 V6
R2.
• XLINK
The XLINK interface is used for HiPath Access and RG 8350 A.
The physical LAN interfaces are configured via AMO and the assignment to the
Ethernet ports is performed via the WBM. Except XLINK. XLINK is configured
completely with YaST. VLANs have to be configured via AMO.
Figure 2 LAN interfaces of HiPath 4000 SoftGate
1.5 Ports
see “Gateways HG 3500 and HG 3575 > Chapter 21, “IP Ports””.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Advantages
1.6 Advantages
HiPath 4000 SoftGate benefits compared with existing branch scenarios:
Existing branch HiPath 4000 SoftGate benefits

scenarios
Remote IP endpoints • Local PSTN connection, local a/b-connection
• Hot-Standby signaling survivability
• Less WAN bandwidth between headquarter and

branch
Small remote side branch • Centralized switch architecture
with HiPath 2000 or HiPath
3000 • Homogenous management with HiPath 4000
Administration
• Homogenous applications
• Less WAN bandwidth between headquarter and

branch
IPDA access point • No proprietary hardware
• More effective TCO
• Video endpoints
Table 1 HiPath 4000 SoftGate advantages compared with existing branch
scenarios
1.7 Restrictions
For all variants of HiPath 4000 SoftGate:
• HiPath 4000 SoftGate is the only application that runs on a standard server
or VMware Virtual Maschine or can be installed on a standard server together
with AP Emergency.
• No active virus scanner for HiPath 4000 SoftGate.
• A maximum number of nine virtual HG 3500 boards and/or HiPath Access

modules can be connetcted to one HiPath 4000 SoftGate.
• For signaling survivability no other ISDN modems as released for HiPath

4000 will be supported.
• Analogue connectivity for voice and fax is not done via AP 1120 HFA but
using SIP Media Gateways Mediatrix 41xx.
• Analogue modem connectivity is not supported.
• No support of H.323 trunking and CorNet IP trunking.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Restrictions
• Codec G.723 is not supported.
• The following restrictions apply when connecting to CO over Mediatrix

gateways:
– Accounting is not supported.
– Callback functionality not supported.
• A maximum number of 83 HiPath 4000 SoftGates 50/1000 or IP Access

Points can bei connected to one HiPath 4000 system.
• Limitations to DMC (see “Payload Switching DMC”, Chapter 4, “Direct Media

Connect (DMC) in Connection with HiPath 4000 SoftGate”):
– End-to-end payload can also be achieved to a native SIP trunk

(depending on the trunk profile).
– The MediaCapabilities (e.g. codecs) can be renegotiated/changed

between the SIP partners (on the HiPath 4000 SoftGate) even after the
DMC connection has been established.
– If a SIP device or a SIP native trunk on the 4000 SoftGate communicates

with an DMC endpoint (not the DMC proxy!), then a MediaRelay is
activated between them on the HiPath 4000 SoftGate. This corresponds
to an RTP proxy which always routes the media stream (RTP) via the
HiPath 4000 SoftGate.
– If a SIP device or SIP native trunk on the HiPath 4000 SoftGate commu-
nicates with a DMC proxy on the common gateway, then the MediaCapa-
bilities are passed on transparent and an E2E payload connection is
established. However due to the restrictions of the DMC proxies on the
CGW, it is not possible to renegotiate codecs.
For HiPath 4000 SoftGate 50 only:

• Provider access requires HiPath Access modules or direct SIP provider
connections.
For HiPath 4000 SoftGate 1000 only:

• Signaling Survivability via PSTN network is not supported for HiPath 4000
SoftGate 1000.
• Provider access requires AP 3700 IP or direct SIP provider connections.
MediaRelay
MediaRelay is a Media proxy of the Media server in the HiPath 4000 SoftGate that
is controlled via the signaling software of the HG 3500.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_01_ziel.fm
Overview
Hardware Requirements
1.8 Hardware Requirements

Please refer to the White List for the latest hardware requirements for a HiPath
4000 SoftGate server. The White List is part of the latest Release Note.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_04_admin.fm
HiPath 4000 SoftGate Upgrade
Upgrade via Loadware Update Manager
2 HiPath 4000 SoftGate Upgrade

The functionalities of both the virtual HG 3575 and the virtual HG3500 (HFA/SIP)
are contained in the HiPath 4000 SoftGate image. All functionalities are therefore
always upgraded at the same time in a HiPath 4000 SoftGate upgrade.
The upgrade is performed either via LW Update Manager (see Section 2.1,
“Upgrade via Loadware Update Manager”) or via the board’s local WBM appli-
cation (see Section 2.2, “Upgrade via the Local WBM in HiPath 4000 SoftGate”).
2.1 Upgrade via Loadware Update Manager

The HiPath 4000 SoftGate image can be transferred either with the LW Update
Manager or with the PCHI tool on the RMX hard disk.
• HiPath 4000 SoftGate image (RPM format with OMF 386 header):
softgate-5.0-0.i586.rpm.abs
• Directory on the RMX hard disk:

:A1H1E:/APSP/LTG/LGA0/
under:
PZKSGW50
LW Update Manager
1. Start the file transfer operation with the HiPath 4000 Assistant’s Loadware
Update Manager:
HiPath 4000 Assistant > Expert Mode > LW Update Manager
Figure 3 HiPath 4000 Assistant: Loadware Update
2. Select the HiPath 4000 SoftGate that you want to upgrade from the list of
boards.
3. The following options are now available:
A31003-H3160-S104-8-7620, 07/2014
Upgrade via the Local WBM in HiPath 4000 SoftGate
• Transfer LW button: The loadware is transferred but not activated. You

can press the Activate LW button either now or later to activate the
loadware on the required boards.
• Transfer and Activate LW button: The loadware is transferred and

activated.
IMPORTANT: Please note that the board is briefly removed from service
when the loadware is being activated.
2.2 Upgrade via the Local WBM in HiPath 4000 SoftGate

1. Activate the local Web-Based Management application.
To do this, select HiPath 4000 Assistant > Expert Mode > Web-Based
Management for HG35xx or activate the application in the browser with the
IP address of HiPath 4000 SoftGate, e.g. https://218.1.24.139.
Figure 4 WBM - Login
2. Log on with user: TRM, ... and the corresponding password.
Figure 5 WBM - starte page
3. Select the menu SW-Update
Figure 6 WBM - Software Update
A31003-H3160-S104-8-7620, 07/2014
4. Transfer the HiPath 4000 SoftGate image with an OMF 386 header:
softgate-5.0-0.i586.rpm.abs
Select the Software Update function.
Figure 7 WBM - Software Update
5. Click the Browse button to enter the HiPath 4000 SoftGate image in the
"Filename" field.
Figure 8 WBM - Software Update: Entering a file
6. Press Load to load the HiPath 4000 SoftGate image.
Figure 9 WBM - Software Update: Loading a file
7. Activate the new software.

After the upload of the image has finished, the screen for activating the new
software appears automatically.
Figure 10 WBM - Software Activation
You now have the possibility to activate the new HiPath 4000 SoftGate image
immediately (with the button Start Immediately) or to schedule the activation
for later (enter the desired date and time in the screen and press Apply).
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
SoftGate_05_mediatrix.fm
Mediatrix Gateways
Released Mediatrix Gateways
3 Mediatrix Gateways
3.1 Released Mediatrix Gateways

• Mediatrix 4402 Advance: 2x BRI (Basic Rate Interface = ISDN S0) (native SIP
Trunking)
– Section 3.3.1, “ISDN (S0) Subscriber (Mediatrix 44xx)”
– Section 3.3.2, “S0 Trunking (Mediatrix 44xx)”
– Section 3.3.3, “ISDN (S0) Data Connections (Mediatrix 44xx)”
• Mediatrix 4404 Advance: 4x BRI (Basic Rate Interface = ISDN S0) (native SIP
Trunking)
– Section 3.3.1, “ISDN (S0) Subscriber (Mediatrix 44xx)”
– Section 3.3.2, “S0 Trunking (Mediatrix 44xx)”
– Section 3.3.3, “ISDN (S0) Data Connections (Mediatrix 44xx)”
• Mediatrix 35xx (2x ISDN PRI =Primary Line Interface) for T1
• Mediatrix 3631 (1x ISDN PRI =Primary Rate Interface) for E1
– Section 3.3.4, “S2 Interface (Mediatrix 36xx)”
• Mediatrix 3632 (2x ISDN PRI =Primary Line Interface) for E1
– Section 3.3.4, “S2 Interface (Mediatrix 36xx)”
• Mediatrix analog adapter 4104, 4108, 4116, 4124 (analog stations)
– Section 3.3.5, “Analog Stations (Mediatrix 41xx)”
• Mediatrix 1204 (analog trunking)
– Section 3.3.6, “Analog Trunking (Mediatrix 1204)”
3.2 Configuration Notes
IMPORTANT: For information on how to configure gateways for the first time with
the IP address, etc., refer to the documentation supplied with the Mediatrix
gateways. The screenshots displayed depict the Mediatrix gateway’s web
interface.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Configuration Examples
More information is available directly from Mediatrix at:

http://www.mediatrix.com or
https://support.mediatrix.com/DownloadPlus/Download.asp
IMPORTANT: G.711 must be always configured, wether T.38 will be used or

G.729. This restriction is valid for all Mediatrix gateways connected directly to a
HiPath 4000 system or connected via an OpenScape Voice system at a HiPath
4000 system.
3.3 Configuration Examples

This section describes, using screenshots, how to configure specific Mediatrix
gateway parameters based on a specific application scenario.
3.3.1 ISDN (S0) Subscriber (Mediatrix 44xx)

A Mediatrix 4400 gateway can simultaneously support both an ISDN subscriber
line and a line to the private network.
3.3.1.1 Requirements
• Every station at a Mediatrix gateway must be configured as an SIP subscriber

in the HiPath 4000.
• Mediatrix 44xx gateways do not support telephony features for ISDN phones.
• Refreshing is not supported for ISDN phone displays.
• ISDN connections are only supported if Mediatrix 44xx gateways are used.
• ISDN voice connections are only supported for stations or trunks that are
configured on the same HiPath 4000 SoftGate.
• Subscriber calls (i.e. for incoming calls from Mediatrix gateway subscribers)
always have to supply their calling number (internal/extension number).
– If the ISDN terminal does not do this, calling number insertion can also be
configured in the Mediatrix gateway as required. A configuration of this
kind is possible in the Mediatrix gateway (e.g. based on the ISDN port).
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
– The connection of multiple ISDN subscribers via an ISDN bus to a

Mediatrix gateway ISDN port may not be straightforward – unless a
distinction can be made between the subscribers based on call type
(bearer type).
3.3.1.2 Sample Scenario with Mediatrix 4402 Gateway
In this sample scenario a Mediatrix gateway is used for subscribers.
Hub
SoftGate
Mediatrix Gateway
4402
Subscriber:
20.1.1.232
ISDN/S0 phone
3250
Figure 11 HiPath 4000 SoftGate scenario with Mediatrix gateway - S0

subscriber
3.3.1.3 Configuration
The figures in this section depict the configuration in the sample scenario.
Overview
• Network -> Host
• Network -> Interfaces
• SIP -> Gateways
• SIP -> Servers
• SIP -> Registrations
• ISDN -> Basic Rate Interface
• Telephony -> Call Routing Config
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Network -> Host
Set Static for the host domain, the default gateway, the DNS source and the
SNTP source.
Figure 12 Mediatrix 44xx Gateway (Subs.) - Network -> Host
Network -> Interfaces
The network interfaces should be configured with unique LAN IP addresses. A

Mediatrix 4400 gateway can support up to 48 network interfaces.
IMPORTANT: Care must be taken when assigning IP addresses to ensure that

they can be reached by HiPath 4000 SoftGate.
A HiPath 4000 SoftGate (or vHG3500)can only operate one network interface in
the Mediatrix gateway. It may be necessary to configure subscriber and trunking
scenarios over a network interface.
Configure a "subscriber interface" in this mask.
IMPORTANT: The name "Subscriber" can be chosen at random and does not
yet define usage.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 13 Mediatrix 44xx Gateway (Subs.) - Network -> Interfaces
SIP -> Gateways
Select the value Subscriber in the "SIP Gateway Configuration" field.
Figure 14 Mediatrix 44xx Gateway (Subs.) - SIP -> Gateways
SIP -> Servers
Enter values for "Registrar Host " and "Proxy Host" in the "SIP Default Servers"
field.
Figure 15 Mediatrix 44xx Gateway (Subs.) - SIP -> Servers
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
SIP -> Registrations
Enter the phone numbers of the ISDN stations for registration at the SIP server.
Add the subscriber terminals and select the SoftGate subscriber. The "User
Name" field contains the telephone number.
Figure 16 Mediatrix 44xx Gateway (Subs.) - SIP -> Registrations
ISDN -> Basic Rate Interface
Configure the ISDN parameters for every interface that should be used.
• Endpoint Type: NT
• Connection Type: e.g.: Point To Multipoint
In a subscriber-only scenario, the other interfaces are generally identical to the

first one. "Exclusive B-Channel Selection" is usually enabled.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 17 Mediatrix 44xx Gateway (Subs.) - ISDN -> Basic Rate Interface
Telephony -> Call Routing Config
Use this mask to define how calls from/to the VoIP network should be routed to
the ISDN telephones.
The example shows a configuration with two stations (3081 and 3082), which are
both connected over an ISDN bus to the gateway’s BRI2. This example assumes
that both subscribers supply their station numbers. This example shows a
number of exceptional configurations for CLIR that are usually only used very
rarely. The Mediatrix gateway also has a default selection for using CLIR.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 18 Mediatrix 44xx Gateway (Subs.) - Telephony -> Call Routing Config 1
The "RequestLineWithCdPtyNmb" configuration may be needed in certain situa-

tions for SIP protocol synchronization between the Mediatrix gateway and HiPath
4000 SoftGate.
Figure 19 Mediatrix 44xx Gateway (Subs.) - Telephony -> Call Routing Config 2
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
3.3.2 S0 Trunking (Mediatrix 44xx)

A Mediatrix 4400 gateway can simultaneously support both an ISDN subscriber
line and a line to the private network.
• ISDN connections are only supported if Mediatrix 44xx gateways are used.
• ISDN voice connections are only supported for stations or trunks that are
• All gateways should be synchronized with a common clock. For instance, the
gateways receive the clock pulse via a direct connection to the public network
or via an internal ISDN S0 line (layer-0 connection) to another synchronized
gateway, as shown in the sample scenario.
3.3.2.2 Sample Scenario with Mediatrix 4402 Gateway
In this sample scenario a Mediatrix gateway is used for s trunking to the public
network.
Hub
SoftGate Central Office
Mediatrix Gateway
4402
Figure 20 HiPath 4000 SoftGate scenario with Mediatrix gateway - Trunking
The figures in this section depict the configuration in the sample scenario.
Overview
• Network -> Host
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
• SIP -> Gateways
• SIP -> Servers
• SIP -> Registrations
• ISDN -> Basic Rate Interface
• Telephony -> Call Routing Config
Network -> Host
Set Static
• in the section Host Name Configuration for Domain Name Configuration

Source,
• in the section Default Gateway Configuration for Configuration Source,
• in the section DNS Configuration for Configuration Source and
• in the section SNTP Configuration for Configuration Source.
Figure 21 Mediatrix 44xx Gateway (Trunking) - Network -> Host
The network interfaces should be configured with unique LAN IP addresses.

Theoretically, a Mediatrix 4400 gateway can support up to 48 network interfaces.
IMPORTANT: Care must be taken when assigning IP addresses to ensure that

they can be reached by HiPath 4000 SoftGate.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
A HiPath 4000 SoftGate (or vHG3500) can only operate one network interface in
the Mediatrix gateway. It may be necessary to configure subscriber and trunking
scenarios over a network interface.
Configure a LAN interface in this mask.
IMPORTANT: The name of the interface can be chosen at random and does not
yet define usage. In this case we call it „LAN“.
Figure 22 Mediatrix 44xx Gateway (Trunking) - Network -> Interfaces
SIP -> Gateways
Configure your SIP gateway now. As Gateway Name you can chose „HG3550“
for example.
Figure 23 Mediatrix 44xx Gateway (Trunking) - SIP -> Gateways
Select the value „LAN“ in the SIP Gateway Configuration section in the field
Network Interface.
Figure 24 Mediatrix 44xx Gateway (Trunking) - SIP -> Gateways
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
SIP -> Servers
Enter the IP address of the virtual HG 3550 in the section SIP Defaul Servers in
the field Proxy Host (in this case 10.3.74.38).
Figure 25 Mediatrix 44xx Gateway (Trunking) - SIP -> Servers
There are no endpoints in the trunking configuration, which is why registration is

not necessary.
IMPORTANT: As the Mediatrix gateway only supports native SIP (not SIP-Q), a
registration mechanism is not provided for trunking.
Figure 26 Mediatrix 44xx Gateway (Trunking) - SIP -> Registrations
ISDN -> Basic Rate Interface
Configure the ISDN parameters for every interface that should be used.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
• Endpoint Type: TE
• Connection Type: e.g.: Point To Point
The ISDN trunking partner/CO provider protocol should be used, where appli-
cable, to ensure that the "Exclusive B-Channel Selection" field is enabled for both
interfaces.
Figure 27 Mediatrix 44xx Gateway (Trunking) - ISDN -> Basic Rate Interface
Telephony -> Call Routing Config
The Mediatrix gateway’s "Telephony - Call Routing Config" setting is not used in
the general scenario for CO trunks (especially not for differentiation based on
E.164 number). Station number handling is usually configured in the HiPath 4000
system (see HiPath 4000 sample configuration for S0 trunking).
It is assumed that the HiPath 4000 transmits all dial patterns (subscr, national,
internat) in E164 ISDN / international format (block dialing must be configured).
The example here refers to a location with the number +49 (30) 430-xxx.
IMPORTANT: The longest number to be processed must be first with these

criteria!
Outgoing calls from the HiPath 4000 SoftGate to the CO Carrier

All dial patterns with an "+" at the beginning arrive on the Mediatrix gateway via
the sip HG3550 interface This way the Mediatrix recognizes that it is an E164
number in ISDN / INTERNATIONAL format. Depending on the requirements of
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
the CO carrier, the number to ISDN-BRI can be modified to a national

("CO_outg_national") or subscriber ("CO_outg_subscr") format. The modification
applies to calling and called numbers.
Criteria/Transformation
Therefore the following criteria/transformation is applied:
• E164 -> E164 or TONE -> TONE.
Incoming calls from the CO carrier to the HiPath 4000 SoftGate

The came applies to incoming calls to the sip HG3550.
The called number in the subscriber format is converted to international

("CO_inc_called") format. If the carrier transmits the called number in national
format, the routing must be changed from "CO_inc_called (.+) +4930\1" to
"CO_inc_called (.+) +49\1".
The incoming number (calling number) is modified depending on format via the
routing entries "CO_inc_calling_subscr_to_4930…" or
"CO_inc_calling_national_to_49…". Different rules apply to the calling number as
to the called number because the called number is always the same (depending
on the carrier either subscriber or national) but the calling number can be different
(subscriber, national or international).
Criteria/Transformation
• Calling E164 -> Calling E164 or Calling TONE -> Calling TONE and
• Called E164 -> Called E164 or Called TONE -> Called TONE.
Figure 28 Mediatrix 44xx Gateway (Trunking) - Telephony -> Call Routing

Config 1
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways

Config 2

Config 3
HiPath 4000 sample configuration for S0 trunking

ADD-
BFDAT:FCTBLK=34,FUNCTION=HG3550&SIP,BRDBCHL=BCHL120,ATTR=SOCO
CHA-
CHA-
BFDAT:CONFIG=CONT,FCTBLK=34,FUNCTION=SIP,LINECNT=20,BCHLCNT=2;
CHA-BFDAT:CONFIG=OK,FCTBLK=34,ANSW=YES;
/* */
ADD-BCSU:TYPE=IPGW,LN=1,LTU=19,SLOT=8,PARTNO="Q2330-X
",FCTID=1,LWVAR=0,FCTBLK=34,BCHLSIP=2,BCHL3550=10,ALARMNO=0;
/* */
ADD-
CGWB:LTU=19,SLOT=8,SMODE=NORMAL,IPADDR=10.3.74.38,NETMASK=255.25
5.255.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=GLOBIF,PATTERN=213,VLAN=NO,VLA
NID=0,DEFRT=0.0.0.0,BITRATE=AUTONEG,TRPRSIP=10,TRPRSIPQ=0,TRPRH3
23=0,TPRH323A=0,TLSP=4060,DNSIPADR=0.0.0.0;
CHANGE-CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=SERVIF,LOGINTRM="TRM";
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=ASC,UDPPRTLO=29100,TOSPL=48,TO
SSIGNL=184,
T38FAX=YES,RFCFMOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO1,CODE
C=G711A,VAD=NO,RTP=30;
REDRFCTN Redundant transmission of the RFC2833 tones in accordance

with RFC2198
RFCDTMF Transmission of DTMF tones in accordance with RFC2833.
RFCFMOIP Transmission of fax/modem tones in accordance with RFC2833
in all IPDA gateways (STMI2/4 (vSTMI) with regard to AMO CGWB & NCUI2+/
4 (vNCUI) with regard to AMO STMIB). This avoids problems and a common
function across all systems is achieved!
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=ASC,PRIO=PRIO2,CODEC=G729A,VAD
=NO,RTP=20;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=ASC,PRIO=PRIO3,CODEC=NONE,VAD=
NO;
CHANGE-
NO,RTP=20;
CHANGE-
NO,RTP=20;
CHANGE-
NO,RTP=20;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=ASC,PRIO=PRIO7,CODEC=G729AB,VA
D=YES,RTP=20;
CHANGE-CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=DSP,JITBUFD=60;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=MGNTDATA,MGNTPN=8000,BUSPN=443
;
CHANGE-CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=WBMDATA,LOGINWBM="HP4K-
DEVEL",ROLE=ENGR;
SU",ROLE=SU;
ADMIN",ROLE=ADMIN;
CHANGE-CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=GWDATA,GWID1="PRIMARY-
RASMANAGERID";
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=H235DATA,SECSUBS=NO,SECTRNK=NO
,GLOBID1="Gateway2003",TIMEWIN=100,GLOBPW=242-191-30-119-188-83-
173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=LEGKDATA,GWNO=119,GWDIRNO=23;R
EGEXTGK=NO;
CHANGE-CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=SIPTRERH,GWAUTREQ=NO;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=SIPTRSSA,SIPREG=NO,REGIP1=0.0.
0.0,PORTTCP1=5060,PORTTLS1=5061,REGTIME=120,REGIP2=0.0.0.0,PORTT
CP2=5060,PORTTLS2=5061;
CHANGE-
CGWB:MTYPE=CGW,LTU=19,SLOT=8,TYPE=DLSDATA,DLSIPADR=10.3.0.200,DL
SPORT=18443,DLSACPAS=YES;
/* */
ADD-
GKREG:GWNO=19,GWATTR=EXTGW&HG3550V2&SIP,GWIPADDR=10.3.74.48,GWDI
RNO=22,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="",SECLEVEL=TRADITIO;
/* */
ADD-BUEND:TGRP=119,NAME="CO AP19
MEDIATRIX",NO=10,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRU
LE=0,ACDPMGRP=0,CHARCON=NEUTRAL;
/* */
ADD-TDCSU:OPT=NEW,PEN=1-19-008-
0,COTNO=21,COPNO=21,DPLN=4,ITR=0,COS=1,LCOSV=1,LCOSD=1,CCT="
",DESTNO=0,PROTVAR=ECMAV2,SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDAN
I=N,ATNTYP=CO,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=31,SATCO
UNT=MANY,ALARMNO=2,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=21,FWDX=1,CH
IMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G
729AOPT,TCCID="",TGRP=119,SRCHMODE=DSC,INS=Y,SECLEVEL=SECURE,DEV
=HG3550CO,BCHAN=1&&6,BCNEG=N,BCGR=1,LWPAR=0,LWPP=0,LWLT=0,LWPS=0
,LWR1=0,LWR2=0,DMCALLWD=N;
/* */
/* ------ LCR example for a national number------ */
/* ------ Number must go out as block dial------ */
/* ------ In the system either "prepared dial" must be activated
------ */
/* ------ or LDPLN end with -Z and dial with # (SIP functionality-
----- */
/* */
ADD-RICHT:MODE=LRTENEW,LRTE=119,LSVC=ALL,NAME="CO
NATIONAL",TGRP=119,DNNO=1-1-
119,DTMFTEXT="",ROUTATT=YES,EMCYRTT=NO,INFO="",PDNNO=0,CONFTONE=
NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO,LINFE
MER=NO,NOINTRTE=NO;
/* */
ADD-LODR:ODR=19,CMD=OUTPULSE,DGTS=49;
ADD-LODR:ODR=19,CMD=ECHO,FIELD=4;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
ADD-LODR:ODR=19,CMD=NPI,NPI=ISDN,TON=INTERNAT;
ADD-LODR:ODR=19,CMD=END;
/* */
ADD-
LDAT:LROUTE=119,LSVC=ALL,LVAL=1,TGRP=119,ODR=19,LAUTH=1,CARRIER=
1,ZONE=EMPTY,LATTR=NONE,VCCYC=4,GW1=19-0;
/* */
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=0-W-0-
Z,LROUTE=119,LAUTH=1,PINDP=NO;
3.3.3 ISDN (S0) Data Connections (Mediatrix 44xx)
3.3.3.1 Requirements for ISDN (S0) Data (Connections)
IMPORTANT: For basic information on installing S0 data scenarios refer to the

description of how to install S0 subscribers and S0 trunking scenarios.
This section describes the special requirements for S0 data connections that also
have to be taken into consideration.
• ISDN data connections are only supported if Mediatrix 44xx gateways are
used.
• ISDN data connections are only supported for stations or trunks that are
IMPORTANT: Direct Media over LAN (DMC) is not possible for S0 data
connections.
• All ISDN S0 gateways for data connections should be synchronized with a

common clock. For instance, the gateways receive the clock pulse via a direct
connection to the public network or via an internal ISDN line (layer-2
connection) to another synchronized gateway.
3.3.3.2 Sample Scenario with two Mediatrix 44xx Gateways
In this sample scenario, one Mediatrix gateway is used for subscribers, while the
other is used for trunking to the public network.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
SWITCH clock synchronization LAN

(only layer2, no call activity ISDN-S0
softGate
if derived from other MXGW)
CentralOffice
ISDN
BRI2 BRI1 BRI2 BRI1
LAN LAN
M XG W M XGW
4402 4402
IS D N Subscriber Trunking ISDN
data (and trunking) gateway d a ta
gateway
Figure 31 HiPath 4000 SoftGate scenario with two Mediatrix gateways
This type of scenario is an alternative to the configuration of subscribers and

trunking within a single gateway. This clock synchronization method is also
needed if more than four ISDN S0 ports are to be configured (up to four S0 ports
are available on a single Mediatrix gateway).
3.3.3.3 Trunking Gateway
Overview
• ISDN -> Basic Rate Interface (BRI 1)
• ISDN -> Status
• Codec Parameter Trunking and Subscriber Gateway
ISDN -> Basic Rate Interface (BRI 1)
The trunking gateway is linked to the public network via the BRI 1 port and
synchronizes itself with the clock pulse received.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 32 Mediatrix Gateway Trunking - ISDN -> Basic Rate Interface 1
The BRI 2 port is used to forward the clock pulse to the subscriber gateway.
Figure 33 Mediatrix 44xx Gateway Trunking - ISDN -> Basic Rate Interface 2
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
ISDN -> Status
A status window indicates that clocking is performed via the BRI1 port which is
connected to the public network. It also shows that the link on the BRI 2 port for
transferring the clock pulse to the subscriber gateway is working (layer-3
signaling is not used for this link).
Figure 34 Mediatrix 44xx Gateway Trunking - ISDN -> Status
3.3.3.4 Subscriber Gateway
Overview
• ISDN -> Status
• Codec Parameter Trunking and Subscriber Gateway
The subscriber gateway is linked to the trunking gateway (alternatively also to the
public network) via the BRI 1 port without layer-3 signaling and synchronizes itself
with the indirect clock pulse.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 35 Mediatrix 44xx Gateway Subscriber - -> Basis Rate Interface 1
ISDN -> Status
A status window indicates that clocking is performed via the BRI1 port which is
clocked either directly or indirectly via the public network.
Figure 36 Mediatrix 44xx Gateway Subscriber - ISDN -> Status
3.3.3.5 Codec Parameter Trunking and Subscriber Gateway
The settings in the CODECS mask are identical for both gateways.
• Bearer-type mapping must be set to "ITC unrestricted" for the "Codec

ClearMode".
• The "ITC" field must contain the value unrestricted.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
• The setting in the "Jitter Buffer" field can be used to improve the data trans-
mission quality if the delay time does not have to be optimized.
Figure 37 Mediatrix 44xx Gateway Subscriber and Trunking - Telephony ->

CODECS
3.3.4 S2 Interface (Mediatrix 36xx)

In this sample scenario a Mediatrix gateway is used for trunking to the public
network.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
HiPath 4000
SoftGate
Central Office
LAN E1
HG 3550 Mediatrix 36xx
IP 198.16.16.181 IP 198.16.16.198
+49 (69) 7600-0
Default gateway
198.16.16.150
Figure 38 HiPath 4000 SoftGate scenario with Mediatrix 36xx gateway - S2

Interface
Overview
• Network -> Host
• SIP -> Gateways
• SIP -> Servers
• SIP > Registrations
• System -> Hardware
• ISDN -> Primary Rate Interface
• ISDN > Status
• Call Router -> Route Config
Network -> Host
Set Static
• in section Host Name Configuration for Domain Name Configuration

Source,
• in section DNS Configuration for Configuration Source,
• in section SNTP Configuration for Configuration Source,
• in section Default Gateway Configuration for Configuration Source.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 39 Mediatrix gateway 36xx - Network > Host
The network interfaces should be configured with unique LAN IP addresses.

Currently only eth5 is used as uplink. Eth1-4 are not used yet (will be used as
ports of a switch).
IMPORTANT: Take care that all IP addresses are reachable by the HiPath 4000
Softgate.
Figure 40 Mediatrix gateway 36xx - Network > Interfaces
You can chek the status by selecting Network -> Status
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 41 Mediatrix gateway 36xx - Network > Status
SIP -> Gateways
Configure your SIP gateway now.
SIP gateway configuration:
For this example we use "Trunking" as the Gateway Name.
In section Gateway Configuration field Network Interface select Uplink.
Figure 42 Mediatrix gateway 36xx - SIP > Gateways
SIP -> Servers
Configuring the vHG 3550 gateway address (198.16.16.181):
In section SIP Default Servers enter the IP address to field Proxy Host.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 43 Mediatrix gateway 36xx - SIP > Servers
SIP > Registrations
There are no endpoints in the trunking configuration, therefore registration is not

necessary.
IMPORTANT: As the Mediatrix gateway only supports native SIP (not SIP-Q), a
registration mechanism is not provided for trunking.
Figure 44 Mediatrix gateway 36xx - SIP > Registrations
System -> Hardware
Hardware configuration of the PRI card.
In section PRI Cards Configuration:
• Select the Line Type (E1 or T1)
• Select Isdn for Signaling
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 45 Mediatrix gateway 36xx - System > Hardware
ISDN -> Primary Rate Interface
Configure the primary rate interface.
Figure 46 Mediatrix gateway 36xx - ISDN > Primary Rate Interface
ISDN > Status
Checking status by selecting ISDN > Status.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 47 Mediatrix gateway 36xx - ISDN > Status
Call Router -> Route Config
The Mediatrix gateway's "Call Router - Route Config" setting is not used in the
general scenario for CO trunks (especially not for differentiation based on E.164
number). Station number handling is usually configured in the HiPath 4000
system (see HiPath 4000 sample configuration for S2 interface).
It is assumed that the HiPath 4000 transmits all dial patterns (subscr, national,
internat) in E164 ISDN / international format (block dialing must be configured).
The example here refers to a location with ISDN number +49 (69) 7600-XXXXX.
IMPORTANT: The longest number to be modified must be first with these

criteria!
Outgoing calls from the HiPath 4000 SoftGate to the CO Carrier

Between Mediatrix Gateway and the HG 3550 interface all numbers are send as
E.164 International ISDN Numbers. This number format is signaled with a "+" at
the beginning of each pattern.
Depending on the CO carriers requirements, the number format send to the ISDN
interface may be modified to type of number "National" ("CO_outg_national") or
"Subscriber" ("CO_outg_subscr").
The modification is executed for calling and called numbers.
Criteria/Transformation:
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
• E164 -> E164 or TONE -> TONE.
Incoming calls from the CO carrier to the HiPath 4000 SoftGate

The same applies to incoming calls to the sip HG 3550.
The called number in the subscriber format is converted to international

("CO_inc_called") format. If the carrier transmits the called number in national
format, the routing must be changed from "CO_inc_called (.+) +4969\1" to
"CO_inc_called (.+) +49\1".
The incoming number (calling number) is modified depending on format via the
routing entries "CO_inc_calling_subscr_to_4969…" or
"CO_inc_calling_national_to_49…". Different rules apply to the calling number as
to the called number because the called number is always the same (depending
on the carrier either subscriber or national) but the calling number can be different
(subscriber, national or international).
Criteria/Transformation:
• Calling E164 -> Calling E164 or Calling TONE -> Calling TONE and
• Called E164 -> Called E164 or Called TONE -> Called TONE.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 48 Mediatrix gateway 36xx - Call Router > Route Config
HiPath 4000 sample configuration for S2 interface

ADD-UCSU:UNIT=AP,LTG=1,LTU=18,LTPARTNO="Q2329-X
",SRCGRP=18,FRMTYPE=SOCOAP,CONNTYPE=APDL,LSRTADDR=198.16.16.186,
APRTADDR=198.16.16.150,LOCID=001,LOCATION="CPCI23
SOFTGATE18",PLCHECK=YES,BCHLCNT=120,CONVLAW=NO,TCLASS=0,ALARMNO=
0,SOCOTYPE=SOCO50;
ADD-
BFDAT:FCTBLK=34,FUNCTION=HG3550&SIP,BRDBCHL=BCHL120,ATTR=SOCO;
CHA-
CHA-
BFDAT:CONFIG=CONT,FCTBLK=34,FUNCTION=SIP,LINECNT=1,BCHLCNT=4;
CHA-BFDAT:CONFIG=OK,FCTBLK=34,ANSW=YES;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=18,SLOT=1,PARTNO="Q2330-X
",FCTID=1,LWVAR=0,FCTBLK=34,BCHLSIP=4,BCHL3550=30,ALARMNO=0;
ADD-
CGWB:LTU=18,SLOT=1,SMODE=NORMAL,IPADR=198.16.16.181,NETMASK=255.
255.255.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=18,SLOT=1,TYPE=GLOBIF,DEFRT=198.16.16.150,BIT
RATE=100MBFD,TRPRSIP=30;
CHANGE-
CGWB:MTYPE=CGW,LTU=18,SLOT=1,TYPE=LEGKDATA,GWNO=199,GWDIRNO=199,
REGEXTGK=NO;
ADD-BUEND:TGRP=18,NAME="AMT SOCO18 S2
",NO=60,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDP
MGRP=0,CHARCON=NEUTRAL;
ADD-
COT:COTNO=60,PAR=RCL&IBSY&ANS&CEBC&CBBN&BSHT&LWNC&NLCR&TSCS&DFNN
&NLRD&NTON;
ADD-COP:COPNO=60,PAR=L3AR&SPTR,TRK=TA,TOLL=TA;
0,COTNO=60,COPNO=60,DPLN=0,ITR=0,COS=1,LCOSV=1,LCOSD=1,CCT="AMT
SOCO18
",DESTNO=0,PROTVAR=ECMAV2,SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDAN
I=N,ATNTYP=CO,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=31,SATCO
UNT=MANY,ALARMNO=2,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=21,FWDX=1,CH
IMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G
729AOPT,TCCID="",TGRP=18,SRCHMODE=DSC,INS=Y,SECLEVEL=TRADITIO,DE
V=HG3550CO,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=0,LWPP=0,LWLT=0,LWPS
=0,LWR1=0,LWR2=0,DMCALLWD=N;
ADD-
GKREG:GWNO=199,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=
1,INFO="";
ADD-
GKREG:GWNO=19,GWATTR=EXTGW&HG3550V2&SIP,GWIPADDR=198.16.16.198,G
WDIRNO=119,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="",SECLEVEL=TRADITIO;
/* -- LCR example for a national number -- */

/* -- Number must go out as block dial -- */
/* -- In the system either "prepared dial" must be activated --
*/
/* -- or LDPLN end with -Z and dial with # (SIP functionality) -
- */
ADD-RICHT:MODE=LRTENEW,LRTE=1011,LSVC=ALL,NAME="AMT-ORT SOCO18
",TGRP=18,DNNO=1-2-
68,ROUTOPT=YES,DTMFCNV=SUFDIAL,DTMFDISP=DIGITS,DTMFTEXT="MFV-
NACHWAHL
",DTMFPULS=PP300,DESTNO=60,ROUTATT=YES,EMCYRTT=NO,INFO="",PDNNO=
0,CHARCON=NEUTRAL;
ADD-LODR:ODR=1011,CMD=OUTPULSE,DGTS=49;
ADD-LODR:ODR=1011,CMD=NPI,NPI=ISDN,TON=INTERNAT;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
ADD-
LDAT:LROUTE=1011,LSVC=ALL,LVAL=1,TGRP=18,ODR=1011,LAUTH=1,CARRIE
R=1,ZONE=EMPTY,LATTR=WCHREG,VCCYC=4,GW1=19-0;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=0-W-0-
Z,LROUTE=1011,LAUTH=1,PINDP=N;
3.3.5 Analog Stations (Mediatrix 41xx)

Analog stations for the "Voice" or "Fax" service can be configured at a Mediatrix
41xx gateway.
IMPORTANT: For this decice only DGW firmware is released as of HiPath 4000
V6. If you use SIP firmware, there is a high risk, that some of your scenarios will
not work.
Analog stations in a Mediatrix 41xx gateway must be configured as SIP

subscribers in HiPath 4000.
Example:
ADD-SBCSU:STNO=25030,OPT=FPP,CONN=SIP,PEN=1-50-3-
0,DVCFIG=S0PP,COS1=2,COS2=2,LCOSV1=1,LCOSV2=1,LCOSD1=1,LCOSD2=1,
DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,PROT=SBDSS1,PERMACT=Y,INS=Y,A
LARMNO=0,OPTIDX=10,RCBKB=N,RCBKNA=N,CBKBMAX=5,HMUSIC=0;
IMPORTANT: The DGW Mediatrix with default settings will not work correctly
with HiPath 4000 V6. Therefore, some of the parameters have to be changed
manually. Please, pay attention to the sections SIP->Servers, SIP->Registra-
tions, SIP->Interop and SIP->Transport.
Management > Access Control
Configure the parameters for line administration and public.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 49 Mediatrix 41xx - Management -> Access Control
Network > Interfaces
Configure the parameters for network settings in this mask. Configure the IP
address, subnet mask, default router and SNMP port.
Figure 50 Mediatrix 41xx - Network -> Interfaces
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Network > Host
Configure the parameters for network settings in this mask. Configure default
router, DNS, SNTP.
Figure 51 Mediatrix 41xx - Network -> Host
Management > Configuration Scripts
The download parameters for the configuration scripts are administered in this
mask.
Enter the values for the configuration file server.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 52 Mediatrix 41xx - Management -> Configuration Scripts
Management > Firmware upgrade
The download parameters for the firmware are administered in this window.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 53 Mediatrix 41xx - Management -> Firmware Upgrade
SIP -> Servers
The parameters for the SIP servers are administered in this mask. Enter the IP
address of the SIP server.
Figure 54 Mediatrix 41xx - SIP -> Servers
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
The parameters for the SIP subscribers are administered in this mask. Enter the
station number and name for each subscriber. This data is also used to display
caller ID information.
Figure 55 Mediatrix 41xx - SIP -> Registrations
SIP -> Interop
For correct functioning of Mediatrix 41xx, it is recommended to set values in

boxes 406 and 488 to Use Previous Media Negotiation.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 56 Mediatrix 41xx - SIP -> Interop
SIP -> Transport
For correct functioning of Mediatrix 41xx, it is recommended to set values for

Transport to Enable.
Figure 57 Mediatrix 41xx - SIP -> Transport
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Telephony -> Codecs
Codec parameters are set in this mask (next three screenshots). The preferred
codec is G.711 a-Law.
Figure 58 Mediatrix 41xx - Telephony -> Codecs
If more than one codec is needed to be allowed, then priority of each codec can
be set under button Edit. Usable values are values in the range from 0 (lowest
priority) to 10 (highest priority).
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 59 Mediatrix 41xx - Telephony -> Codecs
Telephony -> Misc
This mask allows you to configure country settings and custom tones.
• Country Selection germany1 = permanent dial tone
• Country Selection germany2 = interrupted dial tone (3 short beeps)
Figure 60 Mediatrix 41xx - Telephony -> Misc
3.3.6 Analog Trunking (Mediatrix 1204)

HiPath 4000 SoftGate 50 --> SIP trunk --> Mediatrix 1204 --> Analog trunk
3.3.6.1 Configuration on HiPath 4000
Overview
• SoftGate 50 (SOCO) vIPDA shelf 50, direct link configuration with 120 B
channels
• Slot 8, vSIP 04 trunk to Mediatrix 1204 (SIP <==> Telco analog trunk)
• NCUI configuration, LTU 50
• vSIP trunk to Mediatrix 1204 (SIP <==> Telco analog trunk)
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
• Mediatrix 1204 AMO configuration
• Set the Mediatrix proxy (ip 57) on HiPath 4000 / SoftGate 50 / WBM SIP trunk
(ip 58)
• LCR settings
SoftGate 50 (SOCO) vIPDA shelf 50, direct link configuration with 120 B
channels
ADD-UCSU:UNIT=AP,LTG=1,LTU=50,LTPARTNO=”Q2329-
”,SRCGRP=50,FRMTYPE=SOCOAP,CONNTYPE=APDL,LSRTADDR=155.75.27.50,A
PRTADDR=155.75.27.1,LOCID=050,LOCATION="DIRECT LINK,
CPCI#2",PHONE=9727145968,PLCHECK=YES,BCHLCNT=120,CONVLAW=NO,TCLA
SS=0,ALARMNO=0,SOCOTYPE=SOCO50;
Slot 8, vSIP 04 trunk to Mediatrix 1204 (SIP <==> Telco analog trunk)
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=50,SLOT=8,PARTNO="Q2330-X
",FCTID=1,LWVAR=0,FCTBLK=59,BCHL3550=4,ALARMNO=0;
NCUI configuration, LTU 50
CHANGE-STMIB:MTYPE=NCUI2,LTU=50,TYPE=GLOBAL,PATTERN=255;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=IFDATA,VLAN=NO,TOSLAN=72,TOSMODEM=
80,VLANID=0,BITRATE=100MBFD;
CHANGE-STMIB:MTYPE=NCUI2,LTU=50,TYPE=DSP,JITBUFD=60;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=SERVIF,LOGINTRM="TRM",LOGINPPP="PP
P";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=SIGQOS,BANDW=0,MAXRTD=0,MINTHRPT=0
,SIGPTHSW=STD,QOSSTAT=NO;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=ASC,UDPPRTLO=29100,TOSPL=48,T38FAX
=YES,RFCFMOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO1,CODEC=G729
,VAD=NO,RTP=20;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=ASC,UDPPRTLO=29100,T38FAX=YES,RFCF
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO2,CODEC=G729A,VAD=NO,
RTP=20;
CHANGE-
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO3,CODEC=G711U,VAD=NO,
RTP=20;
CHANGE-
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO4,CODEC=G711A,VAD=NO,
RTP=20;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
CHANGE-
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO5,CODEC=G729B,VAD=YES
,RTP=20;
CHANGE-
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO6,CODEC=G729AB,VAD=YE
S,RTP=20;
CHANGE-
MOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO7,CODEC=NONE,VAD=NO,R
TP=20;

with RFC2198
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=H323,Q931T1=50,Q931T2=500,GWNAME="
HG3575-2";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=DMCDATA,DMCALLWD=NO,DMCCONN=0;
CHANGE-STMIB:MTYPE=NCUI2,LTU=50,TYPE=SNMP,CS1="public";
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=MGNTDATA,MGNTPN=8000,BUSPN=443;
CHANGE-STMIB:MTYPE=NCUI2,LTU=50,TYPE=WBMDATA,LOGINWBM="HP4K-
DEVEL",ROLE=ENGR;
SU",ROLE=SU;
ADMIN",ROLE=ADMIN;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=DLSDATA,DLSIPADR=192.0.2.40,DLSPOR
T=18443,DLSACPAS=NO;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=50,TYPE=SOCODATA,CLAIPADR=155.75.27.50;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
vSIP trunk to Mediatrix 1204 (SIP <==> Telco analog trunk)
ADD-
55.255.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=GLOBIF,PATTERN=255,VLAN=NO,VLA
NID=0,DEFRT=155.75.27.1,BITRATE=100MBFD,TRPRSIP=4,TRPRSIPQ=0,TRP
RH323=0,TPRH323A=0,TLSP=4060,DNSIPADR=0.0.0.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=ASC,UDPPRTLO=29100,TOSPL=48,TO
SSIGNL=184,T38FAX=YES,RFCFMOIP=YES,RFCDTMF=YES,REDRFCTN=YES,PRIO
=PRIO1,CODEC=G729,VAD=NO,RTP=20;

with RFC2198
CHANGE-
=NO,RTP=20;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=ASC,PRIO=PRIO3,CODEC=G711U,VAD
=NO,RTP=20;
CHANGE-
=NO,RTP=20;
CHANGE-
NO,RTP=20;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=ASC,PRIO=PRIO6,CODEC=G729B,VAD
=YES,RTP=20;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=ASC,PRIO=PRIO7,CODEC=G729AB,VA
D=YES,RTP=20;
CHANGE-CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=DSP,JITBUFD=60;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=MGNTDATA,MGNTPN=8000,BUSPN=443
;
DEVEL",ROLE=ENGR;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
SU",ROLE=SU;
ADMIN",ROLE=ADMIN;
CHANGE-CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=GWDATA,GWID1="PRIMARYR-
ASMANAGERID";
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=H235DATA,SECSUBS=NO,SECTRNK=NO
,GLOBID1="Gateway2003",TIMEWIN=100,GLOBPW=242-191-30-119-188-83-
173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=SIPTRSSA,SIPREG=NO,REGIP1=0.0.
0.0,PORTTCP1=5060,PORTTLS1=5061,REGTIME=120,REGIP2=0.0.0.0,PORTT
CP2=5060,PORTTLS2=5061;
CHANGE-
CGWB:MTYPE=CGW,LTU=50,SLOT=8,TYPE=DLSDATA,DLSIPADR=192.0.2.40,DL
SPORT=18443,DLSACPAS=NO;
Mediatrix 1204 AMO configuration
ADD-BUEND:TGRP=58,NAME="MEDIATRIX_1204
",NO=8,TRACENO=0,ACDTHRH=*,PRIONO=1,TDDRFLAG=ON,GDTRRULE=0,ACDPM
GRP=0,CHARCON=NEUTRAL;
0,COTNO=59,COPNO=59,DPLN=0,ITR=0,COS=59,LCOSV=1,LCOSD=1,CCT="",D
ESTNO=58,PROTVAR=ECMAV2,SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=
N,ATNTYP=CO,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=31,SATCOUN
T=MANY,NNO=58,ALARMNO=2,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=59,FWDX
=1,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,SRCGRP=50,CLA
SSMRK=EC&G711&G729AOPT,TGRP=58,SRCHMODE=CIR,INS=Y,SECLEVEL=SECUR
E,DEV=HG3550CO,BCHAN=1&&4,BCNEG=N,BCGR=1,LWPAR=2,LWPP=0,LWLT=0,L
WPS=0,LWR1=0,LWR2=0,DMCALLWD=N;
ADD-
COT:COTNO=59,PAR=PRI&RCL&ANS&KNOR&CEBC&CBBN&CBFN&FWDN&FNAN&COTN&
BSHT&BLOC&PROV&ATRS&TSCS&ICZO&TRSC&CFOS&CFVA&PINR&AOCC&BCNE&NTON
;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Set the Mediatrix proxy (ip 57) on HiPath 4000 / SoftGate 50 / WBM SIP trunk
(ip 58)
Figure 61 Mediatrix 1204 Gateway - WBM - SIP trunk profile
The MediatrixGateway folder should be activated, right mouse click > ACTIVATE
==> folder turns green.
LCR settings
AMO WABE - Acces code for outbound call through Mediatrix 1204
ADD-WABE:CD=958,DAR=TIE,CHECK=N;
AMO LDPLN
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=958-W-
Z,PROFIDX=58,LAUTH=1,PINDP=N;
W second "external" dial tone

Z any number and limited to total 22 digits, ended with timeout or # "pound" key by
stations
LDP If Telco is set to 10 digits then better LDP = 958-W-XXXXXXXXXX
AMO LPROF
ADD-LPROF:PROFNAME="SIP TRK SG 50-
8",SRCGRP=1&25&50,LRTE=958,PROFIDX=58;
AMO LDAT - Attribute of CDR and send PUBNUM from station
ADD-
LDAT:LROUTE=958,LSVC=ALL,LVAL=1,TGRP=58,ODR=959,LAUTH=1,CARRIER=
1,ZONE=EMPTY,LATTR=WCHREG&PUBNUM,VCCYC=4;
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
AMO LODR - echo field 3 = Z from “958-W-Z”

ADD-LODR:ODR=959,CMD=NPI,NPI=UNKNOWN,TON=UNKNOWN;
ADD-LODR:ODR=959,INFO="SIP TRK SG 50-9";
AMO RICHT
ADD-RICHT:MODE=LRTENEW,LRTE=958,LSVC=ALL,NAME="MEDTRX1204
508",TGRP=58,DNNO=58,ROUTATT=YES,EMCYRTT=NO,PDNNO=0,CHARCON=NEUT
RAL,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDS
WTCH=NO,LINFEMER=NO,NOINTRTE=NO;
3.3.6.2 Configuration Notes
On Default MDX1204 is set to DHCP. Get a wireshark or ethereal sniffer trace on

mirrored port at customer data switch to find the ip assigned by DHCP to MDX or
ask the customer IT department. If a recovery mode is performed, the Mediatrix
1204 uses the default IP address 192.168.0.1.
Overview
• LAN Settings on fixed IP 155.75.27.57
• General Configuration of Mediatrix 1204
• Configuration with Mediatrix software Unit Manager Express (UME)
• Mediatrix 1204 firmware upgrade
LAN Settings on fixed IP 155.75.27.57
Management > Network Settings
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 62 Mediatrix 1204 Gateway - LAN settings
General Configuration of Mediatrix 1204
Mediatrix 1204 pointing to HiPath 4000 Softgate 50 SIP trubk (AMO BCSU, PEN
1-50-8-0 = IP 155.75.27.58)
Port User Name = Telco Analog Trunk
Connected to the port of MDX, will appear 1234567890 on the display of the
stations on Telco incoming calls from Line 1.
Incoming calls from Line 4 will display 333004 on HiPath 4000 station; destinated
to answer the line 4.
Also utilized on SIP: Invite 333004@ip_addr.
Management > Configuration File
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 63 Mediatrix 1204 Gateway - configuration
Configuration with Mediatrix software Unit Manager Express (UME)
The following changes on MDX1204 requires an installation of Mediatrix software

UMN (Unit Manager Network) on your PC. It can be found on SWS > Partner
Products > Mediatrix 1204 or on Internet (http://www.media5corp.com/support/
mediatrix--media5boss/downloads). Also the documentation is on DMS or on
MDX web site.
The UME (Unit Manager Express) below is a subprogram of UMN.
The Right Mouse Click on Field fxoIfAnalogLineType will show:
• Get = retrieve the parameter and show it.
• Set = send your change of the parameter to MDX.
• mx1204_MIB_line_type_change_set = Telco analog trunk LS or GS on Lines

1 to 4.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 64 Mediatrix 1204 Gateway - Telco analog trunk LS or GS on lines

1 to 4
• mx1204_MIB_enable_incoming_ringing_direct_to_stn
Has enabled on line 1 & 4 the incoming calls to ring direct to HiPath 4000
station. The lines 2 & 3 will receive second dial tone from MDX on incoming
calls from Telco and the external party should dial the HiPath 4000 station
number to be connected.
Figure 65 Mediatrix 1204 Gateway - Enable incoming ringing direct to

station on line 1 and 4
Line 1 on incoming call from Telco will ring on station 25015
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 66 Mediatrix 1204 Gateway - Line 1 on incoming call from Telco will
ring direct on station 25015
• mx1204_MIB_delay_incoming_ringing
Lines 1 & 4 will be delayed in 1 second to ring on HiPath 4000 station from
Telco incoming calls.
Figure 67 Mediatrix 1204 Gateway - Dealy of incoming ringing
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Mediatrix 1204 firmware upgrade
SW version upgraded to:
Figure 68 Mediatrix 1204 - Firmware
Procedure:
• Download the new version from MDX web page (http://

www.media5corp.com/support/mediatrix--media5boss/downloads).
• Use a TFTP software (e.g. 3CDaemon, free on Internet)
• Unzip/Extract the download firmware file to a directory set on TFTP (our

example C:\Documents and Settings\om837441\My Documents\0_Lixo\)
Figure 69 Mediatrix 1204 - Firmware download
Back on MDX, the Server Host is your PC IP Address 155.75.l27.69 where the
3CDaemon is running. Fill the Firmware Location, the final Status you see on
window FW Download.
Path:
Attent that requires only the name SIP_v5.0.27.203_Profile_MX-S5001-02-

E\1204 where the file Setup.inf is located after unzip is done!
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Fehlersuche mit syslog für Mediatrix 44xx und 36xx
C:\Documents and Settings\om837441\MyDocu-

ments\0_Lixo\SIP_v5.0.27.203_Profile_MX-S5001-02-E\1204
FW Download on Restart = REBOOT THE Mediatrix1204 and the 3CDaemons

log will show the FW being transfered (Send of Sip....) from your PC (IP.69) to
MDX1204 (IP.57) as on 3CDaemon screenshot 15:02:00....
Figure 70 Mediatrix 1204 - Managent > Firmware Download
3.4 Fehlersuche mit syslog für Mediatrix 44xx und 36xx

Logging/trace information or debugging messages are sent to an external syslog-
server. Therefore it is necessary to have a reachable syslog server e.g.
3CDaemon. You must configure the Syslog daemon server to capture those
messages. Set the static IP address or domain name and port number of the
device where the syslog-server is running in the Remote Host field.
If no Syslog daemon address is provided by a DHCP server or specified by the

administrator, no messages are sent.
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Figure 71 Syslog - System > Syslog > Diagnostic Traces
In the Service Severity section, select the minimal severity to issue a notification
message for the various services in the corresponding drop-down menus.
When setting severity to Debug all notification messages are issued.
If you want to have detailed log information enable diagnostic traces by setting
the Diagnostic Traces drop-down menu to Enable.
If applicable, define the filter applied to diagnostic traces by clicking the Edit
button in the Filter field.
Figure 72 Syslog - System > Syslog > Diagnostic Traces > Edit
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
Problems with the ISDN interface:
• If you have problems with the ISDN interface (E1/T1/S0) it's recommended to
set ISDN to All.
• You may not want the ISDN stack massages except the Layer 3 information,
which is "ISDN Stack Q.931 Interpreted frames"
• For investigation problems with DTMF-Map, Mapping tables, hunting ... set
Call Router to Debug
• SIP messages can be traced by setting SIP to Debug.
For general problems at least the following needs to be provided:
• An ethereal trace containing the SIP messages.
• A syslog trace with the following values set to debug:
– Integrated Services Digital Network (Isdn)
– Media IP Transport (Mipt)
– SIP Endpoint (SipEp)
– Telephony Interface (TelIf)
– Diagnostic Traces
Click edit for the filters and set to debug or ALL the following traces:
• call Router
• ISDN
• Line
• SIP
• Stream
A31003-H3160-S104-8-7620, 07/2014
Mediatrix Gateways
A31003-H3160-S104-8-7620, 07/2014
SoftGate_06_sbc.fm
Session Border Controller
4 Session Border Controller

A session border controller (SBC) is needed to protect the HiPsth 4000
SoftGate’s IP network from unauthorized access via the Internet.
SBC is needed for:
• Network address translation (NAT)
• Firewall
• Hunting
The session border controller is implemented for native SIP trunking connections
to a SIP service provider, for instance.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_06_sbc.fm
Session Border Controller
A31003-H3160-S104-8-7620, 07/2014
SoftGate_07_video_support.fm
Video Connections
Supported Video Endpoints
5 Video Connections
HiPath 4000 SoftGate offers video support for internal SIP video endpoints.
These endpoints allow high-definition video and audio transmission.
The SIP video endpoints can be connected directly to one or more HiPath 4000
SoftGates as long as DMC connections between the video endpoints are
guaranteed (see Section 5.2, “Prerequisite”). This is possible as well as for a
standalone system as for a networking environment with HiPath 4000 SoftGates.
The system treats SIP video endpoints as normal SIP subscribers.
5.1 Supported Video Endpoints

• LifeSize Express
• LifeSize Team
• LifeSize Room
5.2 Prerequisite
• A video connection can only ever be set up together with a DMC connection.
• All video endpoints must support DMC call flows.
5.3 Restrictions
• Video endpoints are only supported at HiPath 4000 SoftGate.
• No interworking with HFA video endpoints and TDM video endpoints.
• Video is only possible for DMC slave connections (video is not supported for
native SIP lines and non-HiPath-4000 SIP-Q lines).
• A video connection cannot be added to an existing audio connection and SDP

re-negotiation cannot be performed (e.g. video/audio codecs) if the DMC
connection is already ongoing.
• The DMC connection is interrupted if a feature such as hold or transfer is

used. Video connections cannot be established while these functions are
active. The DMC connection is only re-established and video connections can
only be set up when these features have been deactivated.
A31003-H3160-S104-8-7620, 07/2014
Video Connections
Scenarios
• Since ongoing DMC connections do not support SDP re-negotiation, no appli-

cations are supported in conjunction with a video connection (e.g. remote
camera control).
5.4 Scenarios
• High-definition video and audio transmission for conferences
• Peer-to-peer video communication with SIP-based video connections
5.5 Features
A distinction is made between features in connections only between video
endpoints and between video endpoints and audio-only endpoints.
5.5.1 Connections Between Video Endpoints

• Peer-to-peer video communication
• 3-party video conference
• Support for other features (such as CLIP, CLIR, COLP, COLR) depends on
the video endpoint used.
5.5.2 Connections Between Video Endpoints and

Audio-Only Endpoints
Active feature support for video endpoints - features are initiated by the video
endpoint for the audio endpoint:
• 3-party conference with audio and video endpoints

Scenarios:
– An audio endpoint is added to an existing video connection between two

video endpoints => the video connection between the two video
endpoints stays alive.
– A video endpoint is added to an existing voice connection between an

audio and a video endpoint => a video connection is set up between the
two video endpoints.
Passive feature support for video endpoints - features are initiated by the audio-
only endpoint for the video endpoint:
A31003-H3160-S104-8-7620, 07/2014
Video Connections
Configuration
• Basic audio call
• Local SIP 3-party conference
• All SIP features enabled for the video endpoints used.
5.6 Configuration
Since video endpoints are treated as normal SIP subscribers, they are also
configured as such in the system.
For information on how to configure SIP subscribers, refer to Chapter 2, “SIP

Subscriber” in the document "SIP Connectivity".
A31003-H3160-S104-8-7620, 07/2014
Video Connections
Configuration
A31003-H3160-S104-8-7620, 07/2014
SoftGate_08_lan_redundancy.fm
LAN Redundancy
6 LAN Redundancy
For increased resilience, HiPath 4000 SoftGate can be connected with two LAN
cables to different switches/router.
Additionally you have to activate the LAN Redundancy feature in the HiPath 4000
Platform Administration (Portal) or by editing the initialcfg.xml file.
Scenarios when SoftGate server is starting up
Scenario 1: Both LAN cabels are connected
LAN port 1 (1. Slave interface) will always be activated. LAN port 2 (2. Slave
interface) will be on standby.
Scenario 2: Only one LAN cable is connected
The connected LAN port (LAN1 or LAN2) will be used.
Scenario when board is active
If the active LAN port is disconnected/disabled by peer or equipment (when

both LAN ports are connected):
• The Linux OS activates the standby LAN port.
• The "new" active LAN port sends a GRATUITOUS ARP with the same MAC
and IP addresses as the "old" port.
• When the SoftGate Application switches ports, the payload will be lost for < 2
sec - all active connections will be saved and NOT disconnected.
• If the "old" port comes up again, no port switchback will be performed.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_08_lan_redundancy.fm
LAN Redundancy
A31003-H3160-S104-8-7620, 07/2014
SoftGate_09_music_on_hold.fm
Music on Hold (MOH) - HiPath 4000 SoftGate as Music on Hold or Announcement Source Provider
Feature Description
7 Music on Hold (MOH) - HiPath 4000 SoftGate as Music on

Hold or Announcement Source Provider

As of HiPath 4000 V6 the HiPath 4000 SoftGate can act as a music on hold
(MOH) or announcement source provider. It works in a similar way as external
equipment connected to an analog line. The HiPath 4000 SoftGate provides
virtual SLMA board and virtual TMOM board with saved voice files which emulate
real SLMA and TMOM board with connected external music equipment. As music
source audio files are used (for requirements please refer to Section 7.2, “Service
Information”).
Music or announcement can be switched to any destination within HiPath 4000

SoftGate (HFA phone, SIP phone, SIP trunk) as well as to any device in another
access point or host shelf (TDM phone, analog phone, …).
Figure 73 HiPath 4000 SoftGate: Music on hold, announcements

Important Information for Upgrade
If some vSLMA circuits are already configured and upgrade from previous version
to HiPath 4000 V6 R2 is not done using AMO REGEN it is necessary to delete all
vSLMA circuits and configure them again with AMO SSC and AMO RCSU.
Supported Features
The following features are supported:
• Music source external
A31003-H3160-S104-8-7620, 07/2014
Service Information
– For a detailed description of “Music Source External” please refer to the

appropriate chapter of the feature usage examples (http://apps.g-
dms.com:8081/techdoc/en/P31003H3160S103017620/wwhelp/
wwhimpl/js/html/wwhelp.htm?href=musicex_en.html#wp15475).
– using SLMA board
– circuit configured with AMO SSC, TYPE=EXTANN
• Multiple music on hold
– using SLMA board
– circuit configured with AMO RCSU, RECAPL=HMUSIC
– subscribers will be added to the music on hold device with AMO SCSU/
AMO SBCSU/AMO SSCSU
• MOH and announcements for Flexrouting
– For more information on “Flexrouting” please refer to the appropriate

chapter of the feature usage examples (http://apps.g-dms.com:8081/
techdoc/en/P31003H3160S103017620/wwhelp/wwhimpl/js/html/
wwhelp.htm?href=flexrout_en.html#wp24756).
– using SLMA board board
– circuit configured with AMO RCSU, RECAPL=ACDR/ACDMUS
• Synchronized announcements
– For more information on “Synchronized Announcements” please refer to

the appropriate chapter of the feature usage examples (http://apps.g-
wwhimpl/js/html/wwhelp.htm?href=anse1_en.html#wp22347).
– using TMOM board
– circuit configured with AMO TSCSU, DEV=RAS
• Announcement unit
– For more information on “Announcement Unit” please refer to the

appropriate chapter of the feature usage examples (http://apps.g-
wwhimpl/js/html/wwhelp.htm?href=annuni_en.html#wp22336).
– using TMOM board
– circuit configured with AMO TSCSU, DEV=RA/ANS
Details
The SLMA24 board (Q2246-X) or TMOM2 board (Q2214-X or Q2214-X100) can
be configured into one or more HiPath 4000 SoftGate slots with standard AMO
BCSU command.
A31003-H3160-S104-8-7620, 07/2014
Generation (Example)
The supported features work as with a “real” SLMA/TMOM board.
NOTE: Q2146-X is not recommended anymore for vSLMA. There is no

functional problem with that board, however historically the hardware only has
access to two highways (instead of four) and can cause shelf blocking.
NOTE: Additionally in HiPath 4000 V6 TMOM2 boards are also considered as

using only two highways prior to HiPath 4000 V6 R2.15 and should be deleted
and re-added in case blocking occurs.
Requirements for audio files

There are following requirements for the audio files:
• .wav format
• PCM16 encoding
• mono
• 8 kHz sampling rate
7.3 Generation (Example)

SLMA board configuration
The SLMA24 board (Q2246-X) can be configured into one or more HiPath 4000
SoftGate slots with standard AMO BCSU command.
LTG 1 LTU 23 SRCGRP 2 ALARMNO-LTU 0 SOFTGATE50 10 PORTS USED
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -10 - | READY
3 | Q2330-X vHG3500 1 A 0| | Q2330-X | 1 -07 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 172. 20. 12.133 B-CHANNELS : 120 BCHLCNT : 120
| IP MODE : IPV4 DHCP V4 : NO DHCP V6 : NO
| 1. FUNCT : HG3530 240 LINES B-CHANNELS : 120 BCHLCNT : 120
+--------------------------------+-+------------+------------+------------
4 | Q2333-X SLMO24 1 A 0| | Q2333-X | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| MAC ADRESS : 00-01-E3-8B-C1-EA
+--------------------------------+-+------------+------------+------------
A31003-H3160-S104-8-7620, 07/2014
5 | Q2331-X SLMAE A 0| | Q2331-X | 1 -07 - | READY

+--------------------------------+-+------------+------------+------------
| MAC ADRESS : 00-01-E3-96-E2-C7
+--------------------------------+-+------------+------------+------------
6 | Q2329-X SoftGate 1 0| | Q2329-X | 1 -09 - | READY
+--------------------------------+-+------------+------------+------------
| IP MODE : IPV4 DHCP V4 : NO DHCP V6 : NO
+--------------------------------+-+------------+------------+------------
7 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -10 - | READY
8 | Q2214-X TMOM2 A 0| | Q2214-X | 1 -10 - | READY
9 | Q2214-X TMOM2 A 0| | Q2214-X | 1 -10 - | READY
10 | Q2187-X SIUX2 2 0| | Q2187-X | 1 -02 - | READY
Circuit and feature cofiguration

The circuits and the whole features can be configured with AMO SSC or AMO
RCSU or AMO TSCSU in the same way as for real SLMA/TMOM board (see
feature documentation links in Section 7.1, “Feature Description”).
Audio file configuration

The audio files can be configured per circuit by HiPath 4000 SoftGate WBM
Configuration > Announcements:
Figure 74 Audio file configuration with HiPath 4000 SoftGate WBM
If the .wav file is loaded or changed for already active SLMA circuit, the circuit has
to be restarted using RES-DSSU to activate the new .wav file (also virtual board
or whole HiPath 4000 SoftGate can be restarted).
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs
7.4 Relevant AMOs

Language
BCSU d vSLMA-Baugruppe einrichten
e Configure vSLMA board
RCSU ANWENDNG=WMU d Anwendung Wartemusik
SIK
RECAPL=HMUSIC e Music on hold recorder
SSC TYP=EXTANS d Externes Ansagegerät
TYPE=EXTANN e External announcement
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
SoftGate_11_lync_server.fm
Interworking with Microsoft Lync Communication Server 2010
8 Interworking with Microsoft Lync Communication Server

2010
IMPORTANT: This feature is released for vHG3500 (HiPath 4000 Softgate)

connectivity on project-specific basis only!

Interworking is supported between HiPath 4000 and the Microsoft Lync Commu-
nication Server 2010 which is the successor of Microsoft Office Communications
Sever 2007. This interworking provides the capability to interconnect the
Microsoft Lync Communication Server 2010 with the HiPath 4000 enterprise
network via the Mediation Server. Therefore calls to/from Lync Communication
Server 2010 are possible over HiPath 4000 SoftGate via native SIP trunks.
Microsoft Lync Communication Server 2010 connectivity works with native SIP
trunks located on HiPath 4000 SoftGate (direct SIP).
Figure 75 Interworking with Microsoft Lync Communications Server 2010 over

Mediation Server
A31003-H3160-S104-8-7620, 07/2014
Realization
8.3 Realization
Only native SIP trunks located on HiPath 4000 SoftGate are considered for
connectivity to Microsoft Lync Communication Server 2010 (direct SIP).
8.4.1 Restrictions
General restrictions
• Refer is not supported
=> Disable REFER on Lync Mediation Server
• Only valid for HiPath 4000 V6 R1: Secure connectivity is not supported
=> On Lync Mediation Server, disable TLS and SRTP.
• HiPath 4000 SoftGate doesn't support comfort noise.
Feature restrictions
• Dual forking
• Media bypass
• E911
• DNS load balancing is not supported by HiPath 4000
• No tones on Lync Communications Server client after HiPath 4000 station

makes transfer ringing.
• For restrictions on feature basis see Section 8.4.2, “Available Features”

(detailed description for every feature in each section).
8.4.2 Available Features
8.4.2.1 Basic Call
Name and number display
• Incoming calls to HiPath 4000:
• Calling party (Lync Communications Server) will see for basic call dialed
number.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• Called party (HiPath 4000) will see for basic call calling number and name
on first display line.
• Connected party on HiPath 4000 will see for basic call calling number and
name.
• Connected party on Lync Communications Server will see for basic call
dialed number but no name.
• Outgoing calls to Lync Communications Server:
• Calling party (HiPath 4000) will see for basic call dialed number and SIP
trunk name.
• Called party (Lync Communications Server) will see for basic call calling
number and name.1
• Connected party on HiPath 4000 will see for basic call dialed number and
SIP trunk name.
• Connected party on Lync Communications Server will see for basic call
calling number and name.2
• CLIP/CLIR features - Calling Party Name and Number delivery (Allowed and
Restricted).
• Restriction (name and number display): Missed call notification doesn't

include Display Name information associated with the calling party.
• Special note: Used numbering plan is E.164 (ISDN/International).
Codecs
• G.711a-Law, ptime=20msec preferred codec G.711 u -Law
• G.729 is not supported by Lync Communications Server
• G.723 is not supported by HiPath 4000 Softgate and Lync Communications

Server
• Silence suppression for G711 is not possible while different signaling is used.
• Lync Communications Server uses Comfort Noise PT (13)
• vHG 35xx / HiPath 4000 uses attribute: silenceSupp:on - not supported

by Lync Communications Server.
• Restrictions:
1. Exception: If calling/connected number is found in Global Catalog (Active Directory) then the
name from AD is shown for calling/connected party.
2. Exception: If calling/connected number is found in Global Catalog (Active Directory) then the
name from AD is shown for calling/connected party.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• G.729, G.723 is not supported
• Silence suppression is not supported
8.4.2.2 Call Transfer (blind, semi-attended, attended)
The HiPath 4000 user can transfer calls to a Lync Communications Server party.
Attended, Semi attended1 and blind2 transfer are possible.
• Transfer Talking (Attended transfer)

Display - no display update for any device - CO behavior:
Calling party will see after transfer called party name and number and trans-
fered to party will see calling party name and number on first line display.
• Transfer Ringing (Semi attended transfer)
IMPORTANT: Offered at HiPath 4000 side; not at Lync Communications

Server side.
Display - no display update for any device - CO behavior.

fered to party will see calling party name and number on first line display
• Blind transfer
IMPORTANT: Offered at Lync Communications Server side; not at HiPath

4000 side.
Display - transferred party’s display is not updated:

fered to party will see calling party name and number on first line display
8.4.2.3 Call Forwarding
The HiPath 4000 user can forward calls to a Lync Communications Server party.
CFA (Call Forward All), CFA (Call Forward Busy) and CFNA (Call Forward No
Answer) are possible.
• Display forward unconditionally/busy - independent of forward destination
1. only on HiPath 4000 side

2. only on Lync Communications Server side
A31003-H3160-S104-8-7620, 07/2014
Service Information
– Calling party will see called name and number on first line display.
– Diverted-to party will see calling party name and number on first line.
– No visible indication that a call forwarding happened on any display.
• Display forward no reply - independent of forward destination
– Calling party will see called name and number on first line display.
– Diverted-to party will see calling party name and number on first line.
– No visible indication that a call forwarding happened on any display.
Special Note
• Forward switching is done on both sides.
Restrictions and Limitations

• Party A doesn’t get forward information.
• Call forward busy not supported on Lync Communications Server side.
• PBX is not aware of call forwarding.
• Voice mail scenarios on HiPath 4000 side are not possible.
8.4.2.4 Hold and Retrieve
This scenario is possible on both sides, HiPath 4000 and Lync Communications
Server side. It works with the attribute “inactive in both direction”. Local MOH
(Music on Hold) is used on both sides.
8.4.2.5 Three-Way Conferencing
Conference scenarios are possible - CO behavior.
Display - On conference all parties located on HiPath 4000 will show correct
display info for HiPath 4000 conference members. Lync Communications Server
parties will be displayed as external parties.
Display won’t be updated on HiPath 4000 if new members are added at Lync
Communications Server side.
Special Note:
Lync Communications Server side: Party C/HiPath 4000 is added to conference
before party C is connected and invite/from is different to basic call.
Display party C/HiPath 4000 shows the configured (Hipath 4000 system) trunk
name.
A31003-H3160-S104-8-7620, 07/2014
Configuration Example
HiPath 4000 side: no message is sent towards Lync Communications Server with
"Conference" display update.
8.4.2.6 DTMF
Works with 0-15.
8.4.2.7 SDES Support
As of HiPath 4000 V6 R2 secure SIP trunking via SDES to the Microsoft Lync
Communication Server is supported. To use the feature you have to select the
apropriate SIP trunk profile and select the desired SIP Trunk Security Mode.
8.5 Configuration Example
8.5.1 HiPath 4000

Hipath 4000 routing configuration
Trunk and route configuration as described in SIP Connectivity > Chapter 4, “SIP
Service Provider / SIP Carrier” or find here a configuration example.
vHG 3500 configuration

Verifiy that SIP Protocol Variant for IP Networking is set to Native SIP (AMO
CGWB) and Use Profiles for Trunks via Native SIP flag is set:
WBM > Explorer > Voice Gateway > SIP Trunk Profile Parameter
Figure 76 Microsoft-Lync - SIP trunk profile parameter for vHG 3500
As SIP trunk profile Microsoft-Lync must be activated on HiPath 4000 SoftGate on

the SIP Trunk profile page and IP address of Mediation Server has to be
configured on IP Address / Host name field from Proxy tab.
If you want to use secure SIP trunk connections, you have to select the related
mode in the SIP Trunk Security Mode pull down menu.
WBM > Explorer > Voice Gateway> SIP Trunk Profile > Microsoft-Lync
A31003-H3160-S104-8-7620, 07/2014
Figure 77 Microsoft-Lync - SIP trunk profile configuration for vHG 3500
DMC end must be configured with AMO LDAT (e.g. CHANGE-

LDAT:LROUTE=x,LRTEL=1,LATTR=DMCEND;).
configuration example
Trunk configurtion
AMO TDCSU - DEV=HG3550CO
Besides AMO BFDAT, AMO BCSU, AMO BUEND, AMOTDCSU (ECMAV2

protocol) AMO COT and AMO COP is of interest:
ADD-
COT:COTNO=80,PAR=ANS&CEBC&BSHT&BLOC&LWNC&NLCR&TSCS&DFNN&NLRD&NOF
T&NTON;
ADD-COP:COPNO=80,TRK=TA,TOLL=TA;
Routing and numbering plan specific issues see below (AMO TDCSU, AMO COT,
AMO COP).
Common gateway board configuration

AMO CGWB (in the following example with IPADR=192.168.125.44) is used to
configure, the used trunk protocol (native SIP), DNS/SRV server (used by profile)
and the codec list (example has VAD=NO)
The gateway is configured as local gateway with AMO GKREG. RFCFMOIP is set
to NO.
A31003-H3160-S104-8-7620, 07/2014
ADD-
CGWB:LTU=77,SLOT=10,SMODE=NORMAL,IPADR=192.168.125.44,NETMASK=25
5.255.255.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=77,SLOT=10,TYPE=GLOBIF,PATTERN=213,VLAN=NO,VL
ANID=0,DEFRT=192.168.125.234,BITRATE="AUTONEG",TRPRSIP=4,TRPRSIP
Q=0,TRPRH323=0,TPRH323A=0,TLSP=4061,DNSIPADR=0.0.0.0;
CHANGE-
CGWB:MTYPE=CGW,LTU=77,SLOT=10,TYPE=ASC,UDPPRTLO=29100,TOSPL="184
",TOSSIGNL="104",T38FAX=YES,RFCFMOIP=NO,RFCDTMF=YES,REDRFCTN=YES
,PRIO=PRIO1,CODEC=G711A,VAD=YES,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=77,SLOT=10,TYPE=ASC,PRIO=PRIO2,CODEC=G729A,VA
D=NO,RTP="20";
CHANGE-
CGWB:MTYPE=CGW,LTU=77,SLOT=10,TYPE=ASC,PRIO=PRIO3,CODEC=G711U,VA
D=NO,RTP="20";
ADD-
GKREG:GWNO=11,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1
,INFO="Direct SIP to OCS";
ADD-LDAT:LROUTE=300,LSVC=ALL,LVAL=1,TGRP=1,ODR=300,LAUTH=1;
Routing and numbering plan configuration

For outgoing calls block dialing has to be configured for native SIP trunk, dialing
pattern has to end with e.g. '-Z'.
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="0"-
"Z",LROUTE=1,LAUTH=1;
LCR configuration rules depend on the numbering plan, that is used between
HiPath 4000 and Mediation Server.
The recommended numbering plan is NPI= ISDN, TON= INTERNATIONAL

(explicit format).
8.5.2 Microsoft Lync Server/Mediation Server

To complete the Direct SIP configuration with HiPath 4000, perform the following
steps:
1. Add HiPath 4000 vSTMI as a Gateway to the Lync Server Topology
2. Define dial plan by configuring normalization rules.
3. Create a voice policy.
4. Define a trunk configuration.
5. Assign the voice policy that you created to Lync users.
A31003-H3160-S104-8-7620, 07/2014
8.5.2.1 Add HiPath 4000 vSTMI as a Gateway to the Lync

Server Topology
1. Start Topology Builder: Start > All Programs > Microsoft Lync Server 2010
> Lync Server Topology Builder
2. Select PSTN Gateway and define a new gateway:

Right click PSTN Gateways and select New IP/PSTN Gateway
Figure 78 Micorosft Lync Server - Define new IP/PSTN gateway
3. Define New IP/PSTN Gateway dialog:
• Gateway FQDN or IP Address: specify the IP address of the HiPath

4000
• Listening port for IP/PSTN gateway: enter 5060
• Select TCP as Sip Transport Protocol.
Figure 79 Micorosft Lync Server - Properties for new IP/PSTN gateway
4. Select Mediation pools.

Right click Mediation pool, select Edit Properties and click OK and then
click OK again.
A31003-H3160-S104-8-7620, 07/2014
Figure 80 Micorosft Lync Server - Mediation pool properties
5. Select Gateway on PSTN gateway tab and click Add.
Figure 81 Micorosft Lync Server - PSTN gateway properties
6. Gateway has been assigned to Mediation Server. Click OK.
Figure 82 Micorosft Lync Server - Assign gateway to Mediation Server
7. Publish your changes to the Lync Server topology:

Actions panel of the Topology Builder > Topology > Publish
A31003-H3160-S104-8-7620, 07/2014
Figure 83 Micorosft Lync Server - Publish the changes to the Micorosft

Lync Server topology
8.5.2.2 Define Dial Plan Rules
Define the dial plan rules in Lync Server Control Panel.
1. Start Lync Server Control Panel
2. Voice Routing > Dial Plan tab
3. Create normalization rules which permit Lync users to be able to dial HiPath
4000 phone numbers and the PSTN.
4. To commit your changes click Commit and then Commit all.
Figure 84 Micorosft Lync Server - Define dial plan rules
8.5.2.3 Create Voice Policy
Users assigned to specific voice policy will be able to dial out through the Direct
SIP connection to the HiPath 4000 system.
1. Voice Routing > Voice Policy tab
2. Click New. Depending on the scope of the policy you want to create click Site
Policy or User Policy.
A31003-H3160-S104-8-7620, 07/2014
Figure 85 Micorosft Lync Server - Create voice policy
3. Specify a unique name for this voice policy and provide a description.
4. To create a new PSTN usage for this policy click New.
Figure 86 Micorosft Lync Server - Create new PSTN usage
5. Specify a name for the new PSTN usage record. The name must be unique
to this specific voice policy. Also, provide a detailed description of the PSTN
usage record.
6. To assign a route to this PSTN usage click New.
Figure 87 Micorosft Lync Server - Assign a route to the PSTN usage
7. Specify a name for this route, and provide a meaningful description.
8. To assign the HiPath 4000 gateway to this new route click Add.
A31003-H3160-S104-8-7620, 07/2014
Figure 88 Micorosft Lync Server - Assign the HiPath 4000 gateway to the route
9. Select the HiPath 4000 gateway you created earlier.
10. Click OK in all different dialog boxes to complete the creation of the voice
policy.
8.5.2.4 Define Trunk Configuration
The next step is to assign the HiPath 4000 gateway to a trunk associated with a
pool or a site as follows:
1. Lync Server Control Panel > Voice Routing > Trunk Configuration tab
2. Click New. Depending on the scope of the policy you want to create click Site
Configuration or Pool Configuration.
Figure 89 Micorosft Lync Server - Define the trunk configuration
3. Select a pool or site for this trunk configuration.
A31003-H3160-S104-8-7620, 07/2014
4. In the New Trunk Configuration dialog box click OK.
IMPORTANT: Make sure that Enable Media bypass and Enable refer
support check boxes are disabled.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_12_subscriber_redundancy.fm
Gatekeeper Redundancy for HFA Subscriber
Feature Description
9 Gatekeeper Redundancy for HFA Subscriber

The gatekeeper redundancy function for HFA stations offers a further means of
increasing the availability of VoIP terminals in case of:
• Failure of the connection between SoftGate and the host system
• Failure of the HiPath 4000 SoftGate server hardware or
• Errors in the SoftGate application software
9.1.1 Solution concept

Two HiPath4000 SoftGates are connected to one another (redundantly) in a pool.
The "active" or "standby" function is defined by the configuration of the associated
vHG3530 pairs. It is possible to configure both active gateways (AMO CGWB,
SMODE=NORMAL) and standby gateways (AMO CGWB, SMODE=STBYRDY)
within a HiPath 4000 SoftGate. Two vHG 3530 always form a pair. One gateway
has to be configured in HiPath 4000 SoftGate A in this case and the other in
HiPath 4000 SoftGate B.
Both IP addresses (primary gateway and secondary gateway) must be

configured on the HFA phone. This can be administered on the terminal itself or
via DLS.
9.1.2 Switchover
If the connection between CCA/CCB and vNCUI is interrupted (i.e. between the
host system and HiPath 4000 SoftGate), the error message "LTUC OUT OF
ATTENDANCE LIST" is generated and the HiPath 4000 SoftGate is switched
over ("SOFTGATE RECONFIGURATION START") (see AMO HISTA).
The successful switching over of the individual boards is confirmed with "BOARD
RECONFIGURATION OK". The end of the complete switchover is acknowledged
with "SOFTGATE RECONFIGURATION END".
A (5 minute) timer is started when the reconfiguration commences. This timer is

stopped with the message "RECONFIGURATION END". If an END message has
still not been received following expiry of the timer, the message "SOFTGATE
RECONFIGURATION TIME" is issued (AMO HISTA). This can happen if several
HiPath 4000 SoftGates or a large number of subscribers have to be switched over
and simply serves as additional notification that the move is still pending.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
From the FA perspective, it cannot be established whether an error has occurred

at the application or PC level (error or planned shutdown) or whether there is an
IP network error (no connection to HiPath 4000 SoftGate - CCA/CCB).
9.1.3 Prerequisites for switching over

The switchover is only performed if the following requirements are fulfilled:
• The affected AP must be a HiPath 4000 SoftGate.
• The failed HiPath 4000 SoftGate must have a redundancy HiPath 4000
SoftGate available.
• The status of the destination HiPath 4000 SoftGate must be LTU READY.
NOTE: No switch over will be started during the startup of the system or the
startup of the HiPath 4000 SoftGate.
9.1.4 Switchover process

Scenario 1: All vHG 3530 boards in the failed HiPath 4000 SoftGate are
configured as active gateways
Normal status:
Figure 90 HFA gatekeeper redundancy "simple" mode - Normal status
Upon failure of HiPath 4000 SoftGate 18:
A31003-H3160-S104-8-7620, <Document Release Date>

Feature Description
Figure 91 HFA gatekeeper redundancy "simple" mode - Failure of HiPath 4000

SoftGate 18
Scenario 2: There are active vHG 3530 gateways and standby vHG 3530
gateways in the failed HiPath 4000 SoftGate.
Normal status:
Figure 92 HFA gatekeeper redundancy "mixed" mode - Normal status

Feature Description
Figure 93 HFA gatekeeper redundancy "mixed" mode - Failure of HiPath 4000

SoftGate 18
Figure 94 HFA gatekeeper redundancy "mixed" mode - Failure of HiPath 4000

SoftGate 20
The following switchover process applies to both scenarios:

HiPath 4000 SoftGate 18 is no longer accessible owing to a hardware, software
or IT network error (connection to CCA/CCB interrupted). The switchover is
therefore performed:
• HiPath 4000 SoftGate is deactivated. The vHG 3530 gateways have the
status STBYDEF (AB-BPOOL:MTYP=AP;)
• The associated gateways in HiPath 4000 SoftGate 20 are restarted (warm

standby) and enter the status NORMAL.

Service Information
• The HFA stations are rewritten in the database (AMO SBCSU) from position
1-18-3 or 1-18-8 to positions 1-20-3 or 1-20-8 and the HFA terminals register
automatically at the corresponding vHG 3530 gateway (secondary gateway).
• The IP addresses of the boards are not rewritten (as with the previous,
traditional BPOOL concept). These are permanently configured with AMO
CGWB.
• Manual switchover / Manual switchback

A manual switchover can be performed with the AMO command EXEC-USSU,
in other words in case of maintenance work or following an automatic
switchover (in the event of error), for switching back to the original
configuration.
IMPORTANT: If a switchover is performed manually from HiPath 4000

SoftGate 18 to HiPath 4000 SoftGate 20 via AMO (EX-
USSU:ART=SGRED,LTU=18,SWTYPE=...) owing to maintenance work or
the like, the vHG3530 gateways in HiPath 4000 SoftGate 18 enter the status
STBYRDY (AB-BPOOL:MTYP=AP,...;). Only the boards configured in the
relevant BPOOL are switched over here. All other boards in HiPath 4000
SoftGate 18 are not affected by the switchover.

• This feature is only implemented for HiPath 4000 SoftGates.
• This feature is not released in connection with the feature Access Point
Emergency.
• Only virtual boards (vHG 3530) with pure HFA subscribers are switched.
• Boards with trunking functionality are not switched.
• The already existing feature “HFA Standby” (hardware based solution for host
system, shelves and hard AP shelves) remains unchanged.
• With MobileHFA or DeskSharing, a "forced logoff" is performed in case of

failure/switchover of the HiPath 4000 SoftGate. The "visitor" has to log in to
the station again after the switchover.
• For administration or maintenance activities, the HiPath 4000 SoftGate has

to be blocked by AMO AUSS-USSU (status MAN_AMO). This is necessary to
prevent a switchover when the PC is shut down.
• Automatic switchback is not possible, regardless of whether the switchover

was previously performed automatically (failure of HiPath 4000 SoftGate) or
by AMO. The switchback is always performed manually.

• Switchover is possible only for same type of HiPath 4000 SoftGate for active
and standby HiPath 4000 SoftGate (e.g. HiPath 4000 SoftGate 50).
• Only applies up to and including V6 R1: After a switch over from HiPath
4000 SoftGate A to HiPath 4000 SoftGate B (i.e. HiPath 4000 Softgate A is
down or a loss of LAN connectivity) AMO BPOOL will correctly show all ports
in status STBYDEF on HiPath 4000 SoftGate A.
After HiPath 4000 SoftGate A becomes active again, all ports should be in
status STBYRDY, but the ports remain in STBYDEF.
This is also the case if the boards are switched manually back to HiPath 4000
SoftGate A via EXECUTE-USSU:SGRED,<SG B>,HOME;.
AMO BPOOL then shows own ports in status NORMAL, but the standby
Ports remain in status STBYDEF.
This is an indication error of AMO BPOOL and can be solved by ADD-
CGWB:<LTU>,<SLOT>,STBYRDY;.
I.e. there is only a display problem in AMO BPOOL but there is no functional
restriction/problem.

The following generation example corresponds to Scenario 2 shown in Abschnitt
9.1.4, “Switchover process”. Each of the HiPath 4000 SoftGates has NORMAL
and STBYRDY boards (mixed mode).
IMPORTANT: The pairs configured in AMO BPOOL must have the same type in
AMO UCSU, parameter SOCOTYP (e.g.: both SOCO50 or both SOCO1000).
IMPORTANT: The pairs configured in AMO BPOOL cannot be changed. In case

of an incorrect configuration, the pair has to be deleted and then reconfigured.
/* BFDAT NORMAL boards */

EINRICHTEN-
BFDAT:FCTBLK=35,FUNCTION=HG3530,BGBKAN=BKAN120,ATTR="SOCO";
AENDERN-
BFDAT:CONFIG=WEITER,FCTBLK=35,FUNCTION=HG3530,ANZSATZ=240,ANZBKA
N=60;
AENDERN-BFDAT:CONFIG=OK,FCTBLK=35,ANTW=JA;
/* BFDAT STBYRDY boards */
EINRICHTEN-
BFDAT:FCTBLK=45,FUNCTION=STANDBY,BGBKAN=BKAN120,ATTR="SOCO";

/* HiPath 4000 SoftGate 18 boards */

EINRICHTEN-BCSU:TYP=IPGW,LTG=1,LTU=18,EBT=3,SACHNR="Q2330-X
",FCTID=1,LWVAR="0",FCTBLK=35,BKAN3530=30;
",FCTID=1,LWVAR="0",FCTBLK=45;
/* HiPath 4000 SoftGate 18 gateways */
EINRICHTEN-
CGWB:LTU=18,EBT=3,SMODE=NORMAL,IPADR=10.3.83.133,NETMASK=255.255
.255.0, DEFRT=10.3.83.1;
EINRICHTEN-
CGWB:LTU=18,EBT=8,SMODE=STBYRDY,IPADR=10.3.83.138,NETMASK=255.25
5.255.0, DEFRT=10.3.83.1;
/* HiPath 4000 SoftGate 20 boards */
",FCTID=1,LWVAR="0",FCTBLK=45;
",FCTID=1,LWVAR="0",FCTBLK=35,BKAN3530=30;
/* HiPath 4000 SoftGate 20 gateways */
EINRICHTEN-
CGWB:LTU=20,EBT=3,SMODE=STBYRDY,IPADR=10.3.84.33,NETMASK=255.255
.255.0, DEFRT=10.3.84.1;
EINRICHTEN-
CGWB:LTU=20,EBT=8,SMODE=NORMAL,IPADR=10.3.84.38,NETMASK=255.255.
255.0, DEFRT=10.3.84.1;
/* BPOOL HiPath 4000 SoftGate 18/20 */
EINRICHTEN-
BPOOL:MTYP=AP,POOLNR=1,LTUA=18,EBTA=3,LTUB=20,EBTB=3,INFO="SG
18-20 POOL";
Terminal configuration:
Both IP addresses (home gateway and standby gateway) must be known to the
terminal.
Settings made using DLS:
• Active gateway
Main Menu > IP Devices > IP Phone Configuration > Gateway/Server >
Tab Gateway (HFA) / SIP Server > Reg-Address (HFA) / SIP Server
Address
• Standby gateway
Main Menu > IP Devices > IP Phone Configuration > Gateway/Server >
Tab Gateway (Standby) > Reg-Address
• Configuration of subscriber redundancy at the terminal:

Main Menu > IP Devices > IP Phone Configuration > Small Remote Site
Redundancy > Tab SRSR Settings > Checkbox SRSR freigeschaltet
(SRSR Released???)
Settings via WBM:
• OpenStage
Administrator > System > Gateway
Figure 95 OpenStage - Subscriber Redundancy - Gateway
Administrator > System > Standby Gateway
Figure 96 OpenStage - Subscriber Redundancy - Standby Gateway
Administrator > System > Redundancy

Figure 97 OpenStage - Activate Subscriber Redundancy
• optiPoint
Administrator > System > Gateway Settings
Figure 98 optiPoint - Subscriber Redundancy - Gateways
Administrator > System > SRSR Settings

Relevant AMOs
Figure 99 optiPoint - Activate Subscriber Redundancy
Manual switchover
Switching over from HiPath 4000 SoftGate 18 to HiPath 4000 SoftGate 20
EXEC-USSU:ART=SGRED,LTU=18,SWTYPE=<param>;
SWTYPE=ALLE causes switching of all vHG 3530 boards.
SWTYPE=HOME only switches the vHG 3530 boards that do not belong in
normal status to the HiPath 4000 SoftGate specified in the command ("Switch to
Home"). All vHG 3530 boards that do not belong to HiPath 4000 SoftGate 18 are
switched in this case.
9.4 Relevant AMOs
AMO Parameters Sprache/ Beschreibung/Description

Language
BFDAT FUNCTION=STAN d Funktionsblock für Standby konfigurieren
DBY
FUNCTION=STAN e Configure function block for standby
DBY
BCSU FCTBLK d Konfiguration der Funktionsblöcke für
Normal-Betrieb und Standby
FCTBLK e Function block configuration for main board
and standby board

Relevant AMOs
AMO Parameters Sprache/ Beschreibung/Description

Language
CGWB SMODE d Eine vHG 3530 im normalen Modus
(NORMAL) konfigurieren und eine im
Standby-Ready-Modus (STDBYRDY)
konfigurieren
SMODE e Configure one vHG 3530 for normal mode
(NORMAL) and one vHG 3530 for standby
ready mode (STDBYRDY)
BPOOL LTUA d LTU der Haupt-Baugruppe
LTUA e LTU of main board
LTUB d LTU der Standby-Baugruppe
LTUB e LTU of standby board
EBTA d Einbauteilung der Haupt-Baugruppe
SLOTA e Slot of main board
EBTB d Einbauteilung der Standby-Baugruppe
SLOTB e Slot of standby board
USSU ART=SGRED d SoftGate Redundancy
MODE=SGRED e SoftGate Redundancy
SWTYPE d Art der Umschaltung
ALLE: Umschaltung aller vHG 3530
Baugruppen
HOME: Umschaltung der vHG 3530
Baugruppen, die im Normalzustand nicht
auf diesem HiPath 4000 SoftGate
“Zuhause” sind
SWTYPE e Switch type
ALL:switchover of all vHG 3530 boards
HOME: switchover of all vHG 3530 boards
which in normal state are not at home at this
SRSR
Small Remote Side Redundancy

Relevant AMOs

SoftGate_14_survivable_softgate.fm
Survivable HiPath 4000 SoftGate
Feature Description
10 Survivable HiPath 4000 SoftGate

An optional survivability unit can transform a HiPath 4000 SoftGate into a
survivable access point.
Figure 100 Survivable HiPath 4000 SoftGate - Scenario
The survivability unit takes over control of its own HiPath 4000 SoftGate and
every other selected IP Access Point/HiPath 4000 SoftGate without its own
survivability unit if the central control fails (through loss of the IP connection to the
central control or a call control failure).
The synchronization of the APE is done with HiPath 4000 Assistant > Backup &
Restore.
Figure 101 Survivable HiPath 4000 SoftGate - IT network failure
A31003-H3160-S104-8-7620, 07/2014
SoftGate_14_survivable_softgate.fm
Service Information
Figure 102 Survivable HiPath 4000 SoftGate - Call control failure

The feature is only released on standard servers.
Possible configurations:
• Between 1 and 83 HiPath 4000 SoftGates / AP 3700 IP with AP Emergency

(own survivability unit).
• A group of AP 3300 IP, AP 3700 IP and HiPath 4000 SoftGates (w/o

survivability unit) can connect up to an AP 3700 IP / HiPath 4000 SoftGate
with a survivability unit.
10.3 Generation (example)

1. First Installer
Select "Survivable HiPath 4000 SoftGate" deployment.
IMPORTANT: Don’t select an interface for Atlantic LAN. Otherwise Xlink

won’t work!
• For further configuration details, see "Access Point Emergency (APE)",

Chapter 2, “Configuring the APE Feature (Access Point Emergency)”.

SoftGate_15_ipv6.fm
IPv6
Feature Description
11 IPv6

IPv6 is to replace IPv4 in the near future. This is expected to overcome many
limitations and problems that result from using IPv4. The use of IPv6 for VoIP
offers some crucial benefits, for instance:
• With IPv6, NAT (Network Address Translation) will no longer be needed

except for network masquerading, as the total amount of available IP
addresses will be sufficient. When NAT is used, the delivery of audio
packages in VoIP connections requires workarounds, which means that audio
transmission problems may occur.
• IP packet routing is expected to be more efficient.
• IPv6 has built-in quality of service (QoS) capabilities, especially for realtime
applications.
• Signaling (TLS) and payload encryption (SRTP) is also supported with IPv6
(see "Signaling and Payload Encryption (SPE)").

• IPv6 can be used in HiPath 4000 V6 Softgate on the vHG3500 SIP trunking
(SIP-Q and native SIP) routes.
• SIP trunking can be used between different HiPath 4000 V6 systems (SIP-Q)
or between a HiPath 4000 V6 system and an external IPv6 partner, e.g.
OpenScape Voice or SIP service providers (native SIP).
• For internal connectivity, IPv6 can be used between the HiPath 4000 V6
central switch and HiPath 4000 SoftGates (TCP signaling) as well as between
individual HiPath 4000 Softgates (RTP payload).
• Common gateways (HG 3500) and IPDA boards (NCUI) do not support IPv6.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
11.3.1 Important Note
IMPORTANT: Following changes to the IPv6 configuration, an APE backup/

restore must be performed promptly so that the APE can respond if necessary
using the current/valid IP addresses and functionality is thus guaranteed.
11.3.2 IPv6 Networking Connectivity for HiPath 4000

SoftGate (Trunking)
The trunking gateways (virtual HG 3500) on an HiPath 4000 SoftGate support
IPv6 networking connectivity for SIP-Q and native SIP trunking. The released
IPv6 partners are listed in the Release Note.
Figure 103 IPv6 for HiPath 4000 SoftGate (trunking)
Configuration of an IPv6 connection is performed in three steps:
1. Configuring Trunking Gateways in HiPath 4000

2. Configuring the IPv6 Address for HiPath 4000 SoftGate Trunking
Gateway (Next Generation Server)
3. Configuration in the Virtual HG 3500 SIP WBM
11.3.2.1 Configuring Trunking Gateways in HiPath 4000
An IPv6 trunking gateway is added to HiPath 4000 SoftGate like an IPv4 trunking
gateway via AMOs, except for configuring the IP mode.
With each IPv6 trunking gateway in a HiPath 4000 SoftGate, "Dual Stack" mode
or "IPv6 only" mode can be selected, but only if the functionality of the board is
pure trunking (HG3550). This selection is done with AMO CGWB.
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=IPCONF,IP
MODE=DUALSTCK; or
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=IPCONF,IP
MODE=IPV6;
The IPMODE default is IPV4.
"Dual Stack" mode has to be used when both IPv4 and IPv6 have to be supported
on a SIP trunking route configured for IPv6. In this case, IPv6 is preferred. All IPv6
dual-stack partners have to be released explicitly. The released IPv6 partners are
listed in the Release Note. Interworking with Full-ICE devices is not supported.
"IPv6 only" mode has to be used with pure IPv6 partners.
Remarks
• In order to avoid the IPv6 route being bypassed by IPv4 direct media
connections, please ensure that DMCEND is configured for the IPv6 trunking
gateway.
CHA-LDAT:LROUTE=<lroute>,LATTR=DMCEND;
• IPv6 is used for signaling and payload.
• All IPv6 addresses are configured/managed centrally in the Next Generation

Server (NGS) of the HiPath 4000 central switch.
• Switch Dual Stack/IPv6 board to IPv4:

In order to change a board from Dual Stack/IPv6 to IPv4, AMO CGWB has to
be used:
CHANGE-
CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=IPCONF,IPMODE=IPv4;
When an IPv6 or Dual Stack board is changed back to IPv4, all the IPv6
settings related to this board will be disabled automatically (IPv6 address,
trunk profile configuration) or deleted (NGS entry). This means that if a further
change is made back to IPv6 or Dual Stack, the IPv6 address has to be
configured again in the NGS (see also Section 11.3.2.2, “Configuring the IPv6
Address for HiPath 4000 SoftGate Trunking Gateway (Next Generation
Server)”).
11.3.2.2 Configuring the IPv6 Address for HiPath 4000

SoftGate Trunking Gateway (Next Generation Server)
Configuring the IPv6 address for the HiPath 4000 SoftGate trunking gateway is
performed in the Next Generation Server via the HiPath 4000 Administration
Portal.
Following a restart, the vHG 3500 registers with the Next Generation Server and
creates an entry for itself with its IPv4 address. An IPv6 address can now be
configured in the Next Generation Server for the vHG 3500. Following
configuration of the IPv6 address, a restart has to be performed for the vHG 3500
(RES-BSSU).
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
The Next Generation Server is the central point for IPv6 configuration. All IPv6
addresses are configured here.
IMPORTANT: The NGS IP address has to be configured using the HiPath 4000
Platform Administration (Portal).
The NGS can be reached via HiPath 4000 Administration Portal > System >
IPv6 Addresses.
Once a virtual HG 3500 is configured as IPv6 or Dual Stack, it can be assigned

an IPv6 address in the NGS table.
HiPath 4000 Administration Portal > System > IPV6 Addresses
Figure 104 IPv6 address for vHG 3500
HiPath 4000 Administration Portal > System > IPv6 Addresses > Edit
The IPV6 Address, IPV6 Prefix Length and IPV6 IF Name must be specified for
the IPv6 trunking gateway. A DNS Name can be configured optionally.
IMPORTANT: The DNS Name string is used in the contact field of SIP
messages. There is no resolution of the DNS name in the vHG3500 and no
consistency check between the DNS name and the configured IPv4 or IPv6
address.
The interface name (IPV6 IF name) must correspond to the IP interface on the
HiPath 4000 Softgate/HiPath 4000 system (Linux OS), i.e. eth0, eth1, etc.
Figure 105 Options for IPv6 gateway
After configuring the IPv6 parameters, the trunking gateway has to be restarted
(via AMO).
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Figure 106 Status of IPv6 gateway (restart required)
After the restart, the status of the IPv6 trunking gateway should be "Confirmed".
Figure 107 Status of IPv6 gateway (confirmed)
The Status field displays the configuration state of the IPv6 addresses,
separately for each line of the IP address table:
• Changed (orange)
An element of the IPv6 address data (IP address, prefix length, or interface
name) has been modified.
• Fetched (yellow)
The modified IP address data has been retrieved by the corresponding host
(HiPath 4000 SoftGate or HiPath 4000 system). The NGS server now waits
for an acknowledgment returned by the retrieving host, which is sent when
the configuration of the modified IP address data on that host is completed.
• Confirmed (green)
The retrieving host has acknowledged the successful setting of the modified
IP address data.
• Failed (red)
The retrieving host has returned a negative acknowledgement due to errors
while setting the modified IP address data.
Information for "delete" button

The "Delete" button, corresponding to an entry in the NGS table, will only delete
the selected entry in the portal / NGS database. It will not change the primary IP
mode configuration in the HiPath 4000 system database.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
If the selected entry is still an active HiPath 4000 SoftGate, whose IP mode
should be changed from "IPv6 only" or "dualstack" to "IPv4 only", it is mandatory
to change the IP mode with the appropriate AMOs (CGWB, STMIB) before.
Otherwise the entry will re-appear without an IPv6 address after a restart.
This delete operation is mainly intended for entries (e.g. HiPath 4000 SoftGates)
which are not active anymore (e.g. powered off) and should be purged from the
database.
Information on backing up and restoring the Next Generation Server can be found
in Section 11.3.4, “NGS Backup and Restore”.
11.3.2.3 Configuration in the Virtual HG 3500 SIP WBM
IMPORTANT: Each IPv6 trunking gateway still needs an IPv4 address for
administration purposes.
1. Configuring the local gateway
The selected IP mode of an IPv6 trunking gateway can be verified via WBM.
WBM vHG 3500 SIP > Explorer > Basic Settings > Gateway
Figure 108 IP mode of an IPv6 trunking gateway
SDP negotiation in DualStack mode:
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
If DualStack is configured, the vHG 3500 as the SDP negotiation protocol

supports both ICE MicroLite and ANAT (Alternative Network Address Type) for
incoming connections. ICE MicroLite is defined as standard for outgoing
connections, through ANAT can also be configured.
Figure 109 SDP negotiation in DualStack mode of an IPv6 trunking gateway
Following the restart, the HiPath 4000 Softgate recognizes the IPv6 address. It
can be verified via WBM.
WBM vHG 3500 SIP > Explorer > Network Interfaces > System IP Address
Figure 110 IPv6 address of an IPv6 trunking gateway
2. Configuring the trunking partner
Following the AMO configuration of the IP mode and the assignment of the IPv6
address via the NGS of the HiPath 4000 SoftGate trunking gateway, the IPv6
trunking partner must now be configured using the SIP trunk profile (see SIP
Connectivity > Section 3.3, “SIP Trunk Profiles”) in the WBM of the vHG 3500
SIP gateway.
Use of the trunking profile must be activated for the IP networking trunk type used
(SIP-Q or native SIP).
WBM vHG 3500 SIP > Explorer > Voice Gateways > SIP Trunk Profile
Parameter
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Figure 111 SIP trunk profile parameter for IPv6 trunking partner
Use of profiles is activated as standard for native SIP trunks and deactivated for
SIP-Q.
The IPv6 address or the FQDN (Fully Qualified Domain Names) under which the
IPv6 trunking partner can be reached is configured in the SIP trunk profile.
Registrar, Proxy, Outbound Proxy and Inbound Proxy may also have IPv6
addresses.
WBM vHG 3500 SIP > Explorer > Voice Gateways > SIP Trunk Profile
Figure 112 SIP trunk profile for IPv6 trunking partner
WBM vHG 3500 SIP > Explorer > Voice Gateways > SIP Trunk Profile >
<Selected Trunk Partner Profile> >(right-click) Activate
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Figure 113 Status of SIP trunk profile for IPv6 trunking partner
Because SIP trunk profiles have to be used, only one trunking partner can be
configured for each gateway. Please note that, as a result, the number of IPv6
connections on a HiPath 4000 SoftGate depends on the maximum number of SIP
trunking gateways per HiPath 4000 SoftGate (currently limited to 9).
For IPv6/Dual Stack SIP-Q trunking, the profiles SIPQ Trk Without Registration
and SIPQ Trk With Registration are provided.
IPv6/Dual Stack native SIP trunking uses the profiles of the corresponding
released partners.
11.3.3 IPv6 Internal Connectivity
11.3.3.1 Overview
When using IPv6 for internal connectivity, the IP traffic between the HiPath 4000
V6 central switch and the HiPath 4000 SoftGates (TCP signaling), as well as
between individual HiPath 4000 Softgates (RTP payload), will use IPv6.
Figure 114 IPv6 for HiPath 4000 SoftGate (internal connectivity)
IPv6 is used for signaling (HSR connection) and payload (IPDA master
connection). In order to avoid bypassing the internal IPv6 connections by IPv4
direct media connections (DMC), DMC must not be enabled at the endpoints (IP
phone).
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
When a call between two phones located at the same HiPath 4000 SoftGate is
made, only the signaling data (HSR connection) uses an IPv6 connection. The
voice payload between the phones uses IPv4.
When a call between two phones located at two different HiPath 4000 SoftGates
is made, both the signaling data (HSR connection) as well as the voice payload
use IPv6 connections.
Prerequisite: IPv6 operation between the HiPath 4000 V6 central switch and all
relevant HiPath 4000 SoftGates must be configured in the system. The parameter
IPMODE=DUALSTCK must be set for this purpose for each HiPath 4000
Softgate in AMO STMIB.
CHANGE-STMIB:MTYPE=NCUI2,LTU=1,TYPE=IPCONF,IPMODE=DUALSTCK;
The HiPath 4000 Softgate must then be supplied with the new configuration and
restarted (EXEC-USSU:MODE=UPDATAP,LTU=<ap-number>;)!
To configure the internal IPv6 connections, the following address information is

needed:
• IPv6 addresses of all hosts involved, i.e. the HiPath 4000 V6 central switch
and HiPath 4000 SoftGates and possibly APE / Survival HiPath 4000
Softgates.
• IPv4 addresses of the connected devices, in order to route the IP traffic via
the IPv6 connections (tunnel) between the affected hosts.
The Next Generation Server of the HiPath 4000 (HHS) is the central point for IPv6
configuration. All IPv6 addresses are configured/administered here, including:
• every IPv6 address for every HiPath 4000 Softgate
• IPDA LAN host addresses of the HiPath 4000 V6 central switch (DSCXL-V2
or server),
• all IPv6 addresses of all APEs / survival HiPath 4000 SoftGates.
Figure 115 NGS - Administration/configuration of IPv6 addresses
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
The IPv4 addresses are provided locally on each host during installation with the
HiPath 4000 Platfrom Administration (Portal) on both the HiPath 4000 V6 central
switch and the HiPath 4000 SoftGate hosts.
After the first installation is completed, the HiPath 4000 V6 central switch and
HiPath 4000 SoftGates communicate the required IPv4 addresses to the NGS
server using a notify mechanism.
The following addresses are stored in a table residing in the NGS server:
• CC-A, CC-B and CC_APE addresses
• Signaling and payload addresses of every HiPath 4000 SoftGate
The IPv6 addresses have to be confirmed manually. The configuration of an IPv6

address requires specification of 3 elements:
• IPv6 address itself
• IPv6 prefix length
• Name of the network interface the IP address in the Linux OS of the hostis
bound to
Figure 116 NGS - Confirming IPv6 addresses manually
IMPORTANT: - The interface name (IPV6 IF name) must correspond to the

actual IP interface on the HiPath 4000 Softgate/HiPath 4000 system/APE (Linux
OS), e.g. eth0, eth1, etc.
IMPORTANT: HiPath 4000 SoftGate polls the NGS server periodically for
changes on the IPv6 address data. The polling period is a configurable
parameter, where the default value is set to 5 minutes. Since the polling instances
of all interconnected SoftGates operate independently of each other, it will in
general take one full polling period to propagate the information about the
modified IP address data to all these SoftGates. Therefore, the update of all
affected IPv6 connections will also take at least one full polling period.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
11.3.4 NGS Backup and Restore

The NGS database can be backed up and restored in three different ways:
1. Export/ Import tool:
HiPath 4000 Administration Portal > System > IPv6 Addresses
Figure 117 NGS database: Export
Using the "Export" option, the NGS database is exported as an ".xml" file, which
can be handled, edited, printed out with tools like "Microsoft Office Excel":
Figure 118 NGS database: Export file
If needed, the Read/Write (RW) marked fields can be edited manually before
importing the table. The Read Only (RO) marked fields should not be changed
manually.
After editing the table, the file has to be saved as "xml Data".
Figure 119 NGS database: Save export file
The key for accepting or rejecting an entry in the exported table is the PEN (LTU,
Slot) of the board and the address type.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
If a table containing an entry for one board which is no longer configured as IPv6
is imported, the corresponding entry will be dropped during the importing
procedure.
Figure 120 NGS database: Import with warnings
If a duplicate IP address is detected during the importing procedure, the whole

action will fail. In this case, the table has to be rechecked manually in order to
avoid database inconsistencies.
Figure 121 NGS database: Import failed
2. Data Backup/Restore
This will backup the whole HiPath 4000 Administration Portal database, including
the NGS. In case of a restore the administrator is responsible for the consistency
check between the actual configuration in the HiPath 4000 System (RMX
database) and the restored data in the Portal database.
HiPath 4000 Administration Portal > Maintenance > Data Backup > Backup
Figure 122 NGS database: Data backup/restore
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Relevant AMOs
3. System Backup
This will back up the complete HiPath 4000 application including all configuration
data during back up time. Since the system backup covers the rpm packages in
the currently installed version of all components together with the specific
configuration data, a consistent state is always guaranteed.
HiPath 4000 Administration Portal > Maintenance > System Backup >
Backup
Figure 123 NGS database: System backup
11.4 Relevant AMOs
AMO Parameter Sprache/ Beschreibung/Description

Language
CGWB TYP=IPCONF d IP-Konfiguration
TYPE=IPCONFIG e IP configuration
IPMODE=DUALST d IP-Version 4 und IP-Version 6
CK
IPMODE=DUALST e IP version 4 and IP version 6
CK
IPMODE=IPV6 d nur IP-Version 6
IPMODE=IPV6 e IP version 6 only
BCSU TYP=IPCONF d IP-Konfiguration
TYPE=IPCONFIG e IP configuration
IPMODE=DUALST d IP-Version 4 und IP-version 6
CK
CK
IPMODE=IPV6 d nur IP-Version 6
IPMODE=IPV6 e IP version 6 only
SIPCO IPMODE d Possible values: IPV4, DUALSTCK
IPMODE e Possible values: IPV4, DUALSTCK
STMIB IPMODE d Possible values: IPV4, DUALSTCK
IPMODE e Possible values: IPV4, DUALSTCK
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Relevant AMOs

Language
IPMODE=DUALST d IP-Version 4 und IP-Version 6
CK
CK
A31003-H3160-S104-8-7620, 07/2014
SoftGate_15_ipv6.fm
IPv6
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
SoftGate_16_load_balancer.fm
Load Balancing
Feature Description
12 Load Balancing

SIP Load Balancing is deployed to distribute load in SIP-related data traffic in the
IP network. With SIP Load Balancing, the system is able to scale the performance
of participating SIP servers in order to avoid overloading of the server and to
achieve high availability of the SIP services.
Load Balancing distributes calls from a provider connection, an OpenScape UC

or OpenScape Xpression to a number of gateways, for example if the connection
has more than the maximum number of gateway channels. Only one target IP
address can be configured in the case of a provider connection, which means that
one provider connection would have to be available without Load Balancing for
each gateway.
Calls can also be sent selectively by means of their phone number from one
connection to a number of even geographically distributed gateway groups or
HiPath 4000 systems with the help of a routing number (e.g. local area code)
which can be configured for each gateway. Within a group, the calls are sent to
the gateway with the most free channels.
SIP Load Balancing can be activated for every SIP gateway (HG 3500 or vHG
3500 SIP) in the network. If the feature is activated correctly, the participating
gateways register automatically at the SIP Load Balancing server.
As of HiPath 4000 V6 R2.15 SIP Load Balancing is also released for multiple
OpenScape UC Media Server. These cannot register automatically to the SIP
Load Balance server. Therefore, they must be configured manually in the HiPath
4000 SoftGate WBM.

The OpenSIPS Load Balancer is part of the HiPath 4000 SoftGate software
package and will be installed with each HiPath 4000 SoftGate. It runs on a HiPath
4000 SoftGate but has its own IP address (different from the IP address of the
HiPath 4000 Softgate). The IP address is configured during installation.
Using its configured IP addresses, the Load Balancer automatically fetches its
available DNS server names from the DNS server.
The "Load Balancing" feature is deactivated by default and must be activated with
the WBM of the HiPath 4000 SoftGate and the WBM of every participating
gateway.
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
Features
• "Load Balancing" for inbound native SIP trunks towards virtual HG 3500
gateways (HiPath 4000 SoftGate) and vxWorks based HG 3500 gateways
(IPDA) (e.g. SIP Provider or OpenScape UC connectivity).
• Native SIP trunks without registration.
• Virtual HG 3500s of several HiPath 4000 SoftGates and HG 3500 gateways

of several access points can participate in Load Balancing.
• Error logging / tracing with OpenSIPS.
• Security of data communication between vHG 3500/HG 3500 and OpenSIPS

(via authenticated https).
• Failover mechanism for inbound calls, which have been rejected by the
gateway with an error response.
• Status monitoring of configured gateways by the Open SIPS Load Balancer.
• Load Balancing for several gateway groups.
Requirements
• A HiPath 4000 Softgate must be available within the network.
• SIP Load Balancing can only be activated if the use of SIP trunking profiles is
activated in the WBM.
WBM > Explorer > Voice Gateway > (right-click) SIP Trunk Profile
Parameter
• For SIP Load Balancing to function, you must ensure that the (outbound)
proxy settings in the SIP trunking profile are correctly configured.
WBM > Explorer > Voice Gateway > (right-click) SIP Trunk Profile
Parameter
Restrictions
The “SIP Load Balancing” feature can be used only in a “SoftGate Standalone”
deployment. This menas, it is not available for e.g. “Survivable SoftGate”.
IMPORTANT: Generation with AMOs is not possible.
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
12.3.1 Activate SIP Load Balance Server

The SIP Load Balance server is activated via the WBM of the HiPath 4000
Softgate. The IP address of the Load Balancer and the network mask have to be
entered for this purpose.
The HiPath 4000 Softgate has to be restarted every time the Load Balancer is
activated/deactivated or every time the IP address is changed.
WBM > Configuration > SIP Load Balancer > Settings
Figure 124 Activating the SIP Load Balance server
12.3.2 Activate SIP Load Balancing for the Gateways

Select WBM > Explorers > Voice Gateway > (right mouse click) SIP Load
Balancing > Modify
• Participate at SIP load balancing

Select Yes to activate the feature for the Gateway.
• IP Address of the SIP load balance server

Enter the IP address of the SIP Load Balance server. With this IP address,
the gateways can register at the Load Balancer with their data (IP address of
the gateway, number of available B channels, location prefix number).
• Routing Number (1st digit(s)) for incoming calls

Enter the routing number for Load Balancing.
Gateways with the same routing number form a group. The Open SIPS Load
Balancer sends calls to the group with the longest suitable routing number
(i.e. routing numbers do not have to be unique). Gateways without routing
numbers form the group that can receive all calls. Calls that cannot be
assigned to any group are rejected.
Example 1:
Group 1: Routing number 3

A31003-H3160-S104-8-7620, 07/2014
Load Balancing
Example 2:
Group 1: No routing number

Call 1: 7220, Call 2: 3110, Call 3: 3660
In example 1, Call 1 is rejected, Call 2 is sent to Group 1, Call 3 is sent to
Group 2.
In example 2, Call 1 is sent to Group 1, Calls 2 and 3 are sent to Group 2.
Figure 125 Activating SIP Load Balancing of gateways
NOTE: For more information on the "SIP Load Balancing" menu please refer to
the online help of the WBM.
12.3.3 Outgoing/Incoming Calls via SIP Load

Balancing Server
Open WBM > Explorer > Voice Gateway > SIP Trunk Profiles > <SIP provider
sub-folder> > Modify
Section Outbound Proxy:
For the routing of outgoing calls from the gateways via the Load Balancer to i.e.
the provider, the IP address of the SIP Load Balance server has to be configured
as an outgoing proxy in the corresponding trunk profile.
Section Inbound Proxy:
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
A DNS name is configured under Inbound Proxy for IP Address/Host Name. A

number of IP addresses can be defined for this DNS name on the DNS server.
This is important, because the IP address of incoming calls is checked against
proxy or inbound proxy entries. OpenScape UC calls can come from more than
two IP addresses and are then sent via DNS.
NOTE: Instead of the IP address, the DNS server name of the Load Balance
server can be entered as well.
Figure 126 SIP Load Balancer trunk profile parameter
Specific characteristic in case of OpenScape UC Media Server Farms

The SIP Load Balancer knows the IP addresses of the OpenScape UC Media
Server. Thus, inbound and outbound proxies need not to be configured. It is
enough only to enter the proxy (=IP address of the SIP Load Balancer).
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
Figure 127 SIP Load Balancer trunk profile parameter for OpenScape UC Media
Server
12.3.4 SIP Load Balancer Configuration for

OpenScape UC Media Server Farm
See below screenshot for a typical Media Server farm configuration in a large or
very large deployment. Each Media Server has an individual conference dial-in
number known as Trunk number (e.g. +4982700332201) and a general
conference dial-in number known as Additional numbers (e.g.
+4982700332200).
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
Figure 128 OpenScape UC Media Server farm
The following section describes shortly how to configure the HiPath 4000 SIP
Load Balancer (SLB) in combination with a Media Server farm.
The HiPath 4000 SIP Gateways are connecting automatically to the SLB when
the participation at SIP Load Balancing is activated in the HiPath 4000 Gateways.
The Media Servers have to be added manually. Both dial-in numbers, the
individual and the general one, of each Media Server has to be configured in SLB.
This means two entries have to be configured for each Media Server.
The Media Server configuration is done in the WBM of the HiPath 4000 SoftGate.
WBM > Configuration > SIP Load Balancer > Status
• Adding a rule in SLB

Enter all necessary/needed parameters in the text boxes at the bottom of the
page and click Add Rule.
• Changing an existing rule in SLB

If an existing rule must be modified simply add all necessary/needed
parameters again in the text boxes and click Add Rule. The existing rule will
be replaced with new parameters.
Necessary/needed fields
• Slot
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
This field is normally used for the HiPath 4000 configuration slots. In the
Media Server case this parameter should be used as unique identifier. Useful
would be to use e.g. "1" and "11" for the first Media Server to separate the
conference dial-in numbers, "2" and "22" for the second Media Server and so
on.
• Gateway IPv4 Address

IP address of the Media Server (e.g. 192.1.11.182)
• IPv4 Port
SIP port of the Media Server (e.g. 5060)
• Routing Number
Dial-in numbers for the Media Server (e.g. +4982700332200 for "1" and
+4982700332201 for "11")
• Max Number of B-Channels

In best case the maximum possible parallel channels of each Media Server
shall be used. Due to this a limitation of parallel channels from Media Server
side can be prevented. In the example 2000 is used.
Figure 129 Media Server configuration for SIP Load Balancing
NOTE: For information on how to configure the OpenScape UC please refer to

the OpenScape UC documentation.
12.3.5 Load Balancer Status Query

The current status of the Load Balancer can be queried via the WBM of the
HiPath 4000 Softgate.
WBM > Configuration > SIP Load Balancer > Status
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
Up to HiPath 4000 V6 R2.14
Figure 130 SIP Load Balancer status
The currently registered gateways (destinations) are displayed. The PBX number
as a unique ID (pbx1_pbx2_pbx3_ltu_slot), the IP address and the group number
established on the basis of the routing number are displayed for each Load
Balancing destination. A destination is displayed as "enabled" and participates in
Load Balancing if the Load Balancer has successfully polled the gateway with a
SIP OPTIONS request.
The maximum number of configured B channels and the number of B channels

registered currently with the Load Balancer are also displayed for each
destination.
The routing number configured for each group is displayed.
As of HiPath 4000 V6 R2.15
Figure 131 SIP Load Balancer status
The currently registered gateways/OpenScape UC Media Servers are displayed.
• Slot
A31003-H3160-S104-8-7620, 07/2014
Load Balancing
In case of a HiPath 4000 gateway in this column the configuration slot is

displayed. In the Media Server case this parameter should be used as unique
identifier for the Media Servers.
• Gateway IPv4 Address

IP address of the Media Server (e.g. 192.1.11.182)
• IPv4 Port
SIP port of the Media Server (e.g. 5060)
• Routing Number
Dial-in numbers for the Media Server (e.g. +4982700332200 for "1" and
+4982700332201 for "11")
• Max Number of B-Channels

In best case the maximum possible parallel channels of each Media Server
shall be used. Due to this a limitation of parallel channels from Media Server
side can be prevented. In the example 2000 is used.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_17_hfa_at_home.fm
Secure Remote Subscriber
Feature Description
13 Secure Remote Subscriber

The "Secure Remote Subscriber" feature provides HFA features for a remote
subscriber connected over the Internet. Signaling and payload encryption is
supported for the remote subscriber as well as the route through the Internet.

The HiPath 4000 V6 offers an IP-based connectivity between the HiPath 4000
SoftGate (communication service signaling/media control unit) and the endpoints.
These endpoints offer the full HiPath 4000 feature set. The abbreviation HFA is
used for this functionality in the following sections.
A secure IP (TLS/SSL-based) operating mode, called SPE (Signaling and

Payload Encryption), is supported, which means that the signaling and payload
connections are always encrypted even if SPE is not activated.
As of HiPath 4000 V6 R2, the HFA features can also be used on the phones in
the user's remote office. The HFA connectivity via the public internet to HiPath
4000 SoftGate is therefore incorporated. The HiPath 4000 SoftGate is located
with one interface in the public network (WAN interface) and the other interface
in a corporate network (IPDA interface).
13.1.1 Secure IP Connectivity via the Internet

The following picture shows the basic overview of the requested use case.
Figure 132 Secure IP connectivity for remote offices over the Internet
All HFA functions are available to phone users in the remote office.
A31003-H3160-S104-8-7620, 07/2014
Service Information
13.1.2 Secure IP Connectivity with Mobile HFA

The following picture shows the use incorporating the Mobile HFA feature.
Figure 133 Secure IP connectivity for remote offices with Mobile HFA
13.1.3 Secure IP Connectivity with Gatekeeper

Redundancy
The following picture shows the use incorporating gatekeeper redundancy.
Figure 134 Secure IP connectivity for remote offices with gatekeeper

redundancy

The feature is released with HiPath 4000 V6 R2.
A31003-H3160-S104-8-7620, 07/2014
Service Information
13.2.1 Requirements
• The feature requires unrestricted Internet access with a static, public IP
address for the HiPath 4000 SoftGate server/service.
• An IP password must be assigned to the relevant phones in AMO SBCSU:
• The phone in the remote office has to operate in secure mode, it has to be
registered with TLS.
• The WAN interface of the HiPath 4000 SoftGate requires a certificate.
• The phone in the remote office has to use an NTP server (e.g. Internet Pool
NTP) for time synchronization. The simplest way is to use an NTP server pool
(e.g. 0.de.pool.ntp.org).
• For use of mobile HFA:

To achieve a fully working mobile HFA scenario, the visit and home devices
have to be configured on the same HiPath 4000 SoftGate if the visit phone is
the phone in the remote office.
• If a soft client is used in the remote office, the OpenScape Deployment

Service must be used, because a SoftClient gets its transport mode settings
(TCP or TLS) from the DLS.
• If an OpenScape Deployment Service (DLS) is used, both services, DCMP

and DLS, have to be accessible via the public network. You will find additional
information on the topic of "Configuring Home User Terminals for DLS/
DCMP" in the Administrator Manual for the "OpenScape Deployment
Service V7".
13.2.2 General
• Only one endpoint (phone or soft client) and a DSL router are required at the
remote office location (e.g. Netgear, D-Link, FRITZ!Box, etc.). OpenStage
HFA terminals and the OpenScape Personal Edition software are supported
as endpoints.
• The solution is NAT aware and is suitable for a number of HFA devices behind
one NAT router.
• The HiPath 4000 SoftGate offers a dedicated Ethernet port (WAN interface)
for Internet connectivity including the necessary firewall configuration.
• HiPath 4000 SoftGate administration including this feature is performed fully

via the Intranet/enterprise IP connectivity to the HiPath Host System/HiPath
4000 Assistant. External access over the Internet is not necessary.
• Centralized deployment via DLS is optional.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• Bandwidth requirement considerations

Due to the best effort characteristic of the public Internet, a reliable bandwidth
for RTP traffic between the user in the remote office and HiPath 4000
SoftGate WAN access cannot be guaranteed.
Based on our experiences during testing, we can make the following
recommendations.
– Subscriber side connection

The minimum recommended DSL speed for a user with home Internet
access is a DSL 6000 (max. download 6016 kbit/s - max. upload 512 kbit/
s), assuming that this Internet Service Provider access is used in parallel
for standard office working tasks (e.g. e-mail and "normal" Web
browsing).
– HiPath 4000 SoftGate WAN interface

The dimensioning of the bandwidth of the HiPath 4000 SoftGate for
Internet access must be considered carefully. Because the user's devices
in the remote office cannot use DMC functionality, all calls (payload voice
streams) are terminated in the HiPath 4000 SoftGate. For the bandwidth
calculation a payload voice channel (b/d channel in classical PBX
wording) with the corresponding codec parameters based on the existing
bandwidth tables (see Gateways HG 3500 and HG 3575 > Section 3.5,
“Bandwidth Requirements”) and traffic model calculation (http://
intranet.mch4.global-intra.net/syseng/perfeng/tools/nert/index.htm) must
be considered for each device.
Sample calculation for dimensioning HiPath 4000 SoftGate WAN access

with G./11 (without VAD, 20 ms):
– SDSL 1000 kbit/s (Note: symmetric connection, uplink speed/

bandwidth= downlink speed/bandwidth)
– User in remote office uses G.711 without VAD and with 30 ms

sampling time => 85 kbit/s
– This results in (1000/85 = 11.7 -> rounded down by ~5% for signaling
and non-media, e.g. DLS, Picture CLIP) a maximum of 11 parallel
channels
– 11 channels with 1 % probability of blocking results accoring to Erlang

calculator in 5.1599 Erlang (see also Gateways HG 3500 and HG
3575 > Section 3.7, “Traffic Considerations”)
– For 0.15 Erlang per user, this results in (5.1599/0.15 =>) a maximum
of 34 users in the remote office.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Sample calculation for dimensioning HiPath 4000 SoftGate WAN access

with G.729 (without VAD, 20ms):
– SDSL 1000 KBit/s (Note: symmetric connection, uplink speed/

bandwidth= downlink speed/bandwidth)
– User in remote office uses G.729 without VAD and with 20 ms

sampling time => 40 KBit/s
– This results in (1000/40 = 25 -> rounded down for ~5% for signaling
and non-media, e.g. DLS, Picture CLIP) a maximum of 24 parallel
channels
– 24 channels with 1 % probability of blocking results accoring to Erlang

calculator in 15,2950 Erlang (see also Gateways HG 3500 and HG
3575 > Section 3.7, “Traffic Considerations”)
– For 0.15 Erlang per user, this results in (5.1599/0.15 =>) a maximum
of 102 users in the remote office.
IMPORTANT: Mixing of regular users and call center agents via the
same WAN interface is possible. However, in order to guarantee
connection availability to call center agents at all times, these users will
be trafficked at 1 Erlang (36 C.C.S.). The WAN interface is subject to the
same traffic model calculations like other communication models.
• Notes
– HiPath 4000 SoftGate has its own voice firewall based on HFA. It
therefore behaves like a voice firewall. If customers require additional
protection of the HiPath 4000 SoftGate server and the corporate IT
network, however, this can be achieved by setting up a DMZ. See also
Section 13.2.4, “DMZ”.
– Most providers of standard home (user) Internet connections perform a

forced disconnect after 24 hours. The time of this forced disconnect can
be controlled with many of the IADs (e.g. 03:00h). This disconnect leads
to loss of any active calls and reregistration of the phone. This process
corresponds to a "normal" L1 error.
– Where mobile HFA is used, the disconnect described in Note 2 leads to

the logging off of the mobile HFA.
A31003-H3160-S104-8-7620, 07/2014
Service Information
13.2.3 Restrictions
DMC is not supported for remote office phones. When the terminal is registering
at the HiPath 4000 SoftGate, it is detected as a remote subscriber and therefore
automatically not treated like a DMC endpoint by the system, regardless of the
AMO SDAT parameter DMCERL. To support partial DMC routes to the last
possible endpoint (in this case the HiPath 4000 SoftGate itself) it is recommended
to activate DMCERL in AMO STMIB for the HiPath 4000 SoftGate.
13.2.4 DMZ
In most cases where the customer requires additional protection, an additional
primary DMZ firewall where possible should suffice. In addition to the constantly
active internal HiPath 4000 SoftGate voice firewall, this additional firewall could
be activated between the Internet and the HiPath 4000 SoftGate.
In the following example we consider a DMZ scenario, which consists of both a

primary and a secondary DMZ firewall.
Bild 135 DMZ scenario
Figure 135 shows a network plan with a DMZ scenario consisting of corporate/
enterprise network, DMZ private and DMZ public/Internet. If such a DMZ is to be
used, it must be checked whether all required ports have been enabled in the
DMZ firewalls (typically primary and secondary DMZ firewalls).
A31003-H3160-S104-8-7620, 07/2014
Service Information
Bild 136 DMZ scenario - Required ports
Figure 136 shows a DMZ scenario from another perspective, in which the
required ports will be discussed in greater detail. The respective ports as well as
other ports are listed below and can also be found in the HiPath 4000 V6 Security
Checklist.
The following ports (with reference to Figure 135 and Figure 136) have to be open
in the firewall:
Primary DMZ firewall

• Internet/Public (Untrust) => DMZ Public (Trust)
– TCP 4061 for Cornet TC/TLS
– TCP 1300 for H.323/TLS
– UDP ports for SRTP media (Default = 29100-30099, AMO

STMIB:WANFD)
Optional:
– TCP 443 for Picture CLIP
– TCP 18080/18443 for DLS and DCMP (e.g. use of SoftClient or Software
Lifecycle)
• DMZ Public (Trust) => Internet/Public (Untrust)
– UDP 123 for NTP synchronization of HiPath 4000 SoftGate via the
Internet
– UDP ports for SRTP media (Default = 29100-30099, AMO

STMIB:WANFD)
– Deny/drop rule for all other traffic
– No NAT
A31003-H3160-S104-8-7620, 07/2014
Service Information
– Proxy (ARP) for Public IP
HINWEIS: The blocking of DMZ Public (Trust) => Internet/Public (Untrust)

traffic is for the prevention of misuse of the HiPath 4000 SoftGate server and
the public IP.
Secondary DMZ firewall

• Corporate/Enterprise Network (Trust) => DMZ Private (Untrust)
– TCP 4000 for the HSR signaling protocol. For signaling survivability,
please refer to Section "Signaling Survivability" for the relevant ports.
– TCP 443/22 for WBM/SSH administration ports
– UDP ports for (S)RTP media (Default = 16384-<n - Ports>) - see HG 3500
and HG 3575 Gateways > Chapter 21, “IP Ports”.
– UDP ports for (S)RTP media (Default = 29100-30099) - see HG 3500 and
HG 3575 Gateways > Chapter 21, “IP Ports”.
– Deny/drop rule for all other traffic
– No NAT
– Static routing
Optional:
– TCP 4060 for Cornet TC/TCP: HFA terminal registers from the corporate/
enterprise network.
– TCP 4061 for Cornet TC/TLS: HFA terminal registers from the corporate/
enterprise network.
– TCP 1300 for H.323/TLS: HFA terminal registers from the corporate/
enterprise network.
– TCP 1720 for DMC (e.g. HiPath 4000 SoftGate vNCUI DMC activated)
– TCP 18443/18444 for DLS functionality. Additional ports may be

necessary depending on the manner of use of the DLS. See OpenScape
Deployment Service Documentation or Release Note for a detailed list of
ports.
• DMZ Private (Untrust) => Corporate/Enterprise Network (Trust)
– UDP ports for (S)RTP media (Default = 16384-<n - Ports>) - see HG 3500
and HG 3575 Gateways > Chapter 21, “IP Ports”.
– UDP ports for (S)RTP media (Default = 29100-30099) - see HG 3500 and
HG 3575 Gateways > Chapter 21, “IP Ports”.
Optional:
A31003-H3160-S104-8-7620, 07/2014
Service Information
– TCP 1720 for H.323/TCP: HFA terminal registers from the corporate/
enterprise network.
– TCP 1720 for DMC (e.g. HiPath 4000 SoftGate vNCUI DMC activated)
– UDP ports for DMC from optiPoint (Default=5004-ff) / OpenStage

(Default=5010-ff) terminals (see documentation for terminals).
– TCP 443 for HiPath Backup Server (e.g. use of automatic restore
concept)
– TCP 8082/8084/8085 for DLS functionality: Additional ports may be

necessary depending on the manner of use of the DLS. See OpenScape
Deployment Service Documentation or Release Note for a detailed list of
ports.
HINWEIS: Open ports in the direction of the protected corporate/enterprise

network (known as firewall pinholes) should be avoided for safety reasons if
possible, but are required for the above-named exception scenarios.
13.2.5 Deployment Service (DLS) and DLS Contact-

Me Proxy (DCMP) - Tips & Tricks
13.2.5.1 Background
Under normal circumstances, the Deployment Service (DLS) contacts the IP

terminals via their IP address when a job has been created. In our remote office
case, however, the IP terminals are located in the Internet, as it were behind a
NAT router with a local IP address, which means that the DLS cannot reach them.
The DLS and IP terminals support a proprietary solution in this case, which allows
administration of IP terminals behind a NAT router. This solution is called DLS
Contact-Me Proxy (DCMP). Communication is always opened by the IP terminal
in this solution.
13.2.5.2 How it Works
The IP terminals poll the DCMP in a defined polling interval in this case and use
the device ID to check whether the DCMP has a job active for the DLS for the
respective IP terminal. If this is the case, the IP terminal contacts the DLS in order
to execute the job in question. Once completed, the DLS deletes the Contact-Me
entry in the DCMP again.
A31003-H3160-S104-8-7620, 07/2014
Service Information
IP requirement:
In order for the IP terminals to access the DLS and DCMP, both must be
accessible for the IP terminals via a public IP address. In other words from the
Internet in the case of the remote office scenario.
Hardware requirement:
The DLS server requires two network cards for this solution. One network card
sets up the connection to the corporate/enterprise network and the second is
intended for the connection to the IP terminals in the Internet/NAT router.
13.2.5.4 Information on Configuration
The examples/information below refer to the DLS configuration from the DMZ
scenario example (Figure 136) in Section 13.2.4, “DMZ”.
• The two network cards have to be configured first under Windows.

C:\Documents and Settings\dls-dmz>ipconfig
Windows IP Configuration
Ethernet adapter DMZ WAN:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 220.20.20.100
Subnet Mask . . . . . . . . . . . : 255.255.255.248
Default Gateway . . . . . . . . . : 220.20.20.97
Ethernet adapter DMZ LAN:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 10.10.99.150
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
• The default gateway was configured for the DMZ-WAN interface. A
permanent static route therefore has to be configured for the DMZ-LAN in
order to access the corporate/enterprise network.
C:\Documents and Settings\dls-dmz>route ADD -p 10.10.0.0 MASK
255.255.0.0 10.10.99.254
C:\Documents and Settings\dls-dmz>route print
=============================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 1b 21 15 3d 7b ...... Intel(R) PRO/1000 MT Server
Adapter - Packet Scheduler Miniport
A31003-H3160-S104-8-7620, 07/2014
Service Information
0x3 ...00 19 99 19 95 09 ...... Broadcom NetXtreme Gigabit

Ethernet - Packet Scheduler Miniport
=============================================================
=============================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 220.20.20.97 220.20.20.100 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
10.10.0.0 255.255.0.0 10.10.99.254 10.10.99.150 1
10.10.99.0 255.255.255.0 10.10.99.150 10.10.99.150 20
10.10.99.150 255.255.255.255 127.0.0.1 127.0.0.1 20
10.10.255.255 255.255.255.255 10.10.99.150 10.10.99.150 20
220.20.20.96 255.255.255.248 220.20.20.100 220.20.20.100 20
220.20.20.100 255.255.255.255 127.0.0.1 127.0.0.1 20
220.20.20.255 255.255.255.255 220.20.20.100 220.20.20.100 20
224.0.0.0 240.0.0.0 10.10.99.150 10.10.99.150 20
224.0.0.0 240.0.0.0 220.20.20.100 220.20.20.100 20
255.255.255.255 255.255.255.255 10.10.99.150 10.10.99.150 1
255.255.255.255 255.255.255.255 220.20.20.100 220.20.20.100 1
Default Gateway: 220.20.20.97
=============================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
10.10.0.0 255.255.0.0 10.10.99.254 1
• Install the DLS on the Windows machine with DCMP (in this example, the
DCMP is installed on the same machine). If the DLS has already been
installed without the DCMP, it can be installed later. Detailed service
documentation can be found in the administrator documentation for
OpenScape Deployment Service V7 > Installation and Initial
Configuration > Set Up DCMP.
• To configure the DCMP, navigate to http://<ip address>:18080/dcmp using

a web browser. The user name is "admin". If the DCMP was installed together
with the DLS, the password is the same as the admin password for the DLS.
• Please check and configure the Local Host field under Cluster Setup. This
contains the IP address of the DCMP server. This example simply considers
a standalone DLS without DLS cluster. Refer to the administrator
documentation for OpenScape Deployment Service V7 for additional
information.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Bild 137 DCMP configuration for Secure Remote Subscriber
• The next step involves configuring the DLS for the DCMP.
1. Click the Toggle DCMP button under Administration > Workpoint

Interface Configuration > DCMP tab in order to activate the DCMP.
2. If the DCMP is running on the DLS computer, the IP address of the DCMP
server will be displayed in the DLS-DCMP Host field (or localhost),
otherwise it must be entered here.
3. To test the communication between the DLS and DCMP, click the Test
button.
4. The IP address to be contacted by the IP terminals must be entered in the
Device-DCMP Host field (thus the IP address which is to be accessible
from externally).
5. Define one or more Device IP Ranges. Each IP terminal within the IP
range defined by IP Address from and IP Address to is updated via the
DCMP. The DSL therefore always sends a message to the DCMP with a
request to set the Contact-Me entry for this phone whenever a change is
made to a phone within one of the listed IP ranges. In our example, the
problem is that it is not always clear from which Internet Service Provider
the respective IP terminal receives its IP address range. We have
therefore entered the entire IP address range, with the exception of the
corporate/enterprise network. If accurate IP address ranges must be
known, only those needed can of course be entered. For example, IP
terminals only register from a single ISP for which the IP address range
is known.
6. A Poll Interval must also be assigned to the respective IP address range.
This is the time in minutes after which the IP terminal polls the DCMP. A
very short polling interval (e.g. 1 minute) can be selected for test
purposes. Longer intervals are recommended in live mode.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Bild 138 Configuring the DLS for the DCMP
• The DLS/DCMP configuration can now be tested with an IP terminal in the

remote office.
After entering the DLS/DCMP IP address (in the example 220.20.20.100) at
a terminal in the remote office, the IP terminal registers with the DLS.
Because the IP of the IP terminal is from an IP address range (public Internet
IP address of the remote office NAT router) that was previously entered under
the DCMP configuration, the IP terminal is informed that this is a DCMP
terminal.
Go to the IP Devices > IP Device Management > IP Device Configuration
> DCMP tab. The checkbox DCMP active should be activated.
Bild 139 Testing the DLS/DCMP configuration with an IP terminal in the

remote office
To test the function, go to IP Devices > IP Phone Configuration > Gateway

/ Server of the previously newly registered IP terminal and start reading the
configuration. A job is thus generated. To see the job, go to Job
Coordination > Job Control.
Click the List Entries menu on the DCMP user interface. You should see the
Contact-Me job in the list. The Device ID should be the MAC address of the
phone.
A31003-H3160-S104-8-7620, 07/2014
Bild 140 DCMP - List Entries menu before the IP terminal has fetched the
Contact-Me job from the DCMP
The job should then be concluded once the IP terminal has fetched the job
from the DCMP. The job likewise disappears from the DCMP List Entries
menu when it has been fetched.
Bild 141 DCMP - List Entries menu after the IP terminal has fetched the
Contact-Me job from the DCMP
HINWEIS: If the job is not executed/fetched, a Wireshark trace on the DLS

and/or DCMP side may assist in diagnosing the fault. With the Wireshark
trace, incoming packets must be received on the default port 18080 from the
IP terminal (IP address of the remote office NAT router). This is the polling of
the DCMP by the IP terminal. Communication from the IP terminal to the DLS
must then take place on the default port 18443 for executing the job.
• Another DLS setting that makes sense in our example is the default job
execution type under Job Coordination > Job Configuration. The
Immediately (Execute immediately) option is set here by default. In the case
of Secure Remote Subscribers it might well be that users disable their IP
terminals in the remote office or disconnect them from the mains. The jobs
would therefore not be executed after a certain time and would expire with
"Timed out". It is recommended in this case to switch to Immediately or after
registration.

The next diagram roughly outlines the IP communication relationship between
the SPE-enabled HFA device and the HiPath 4000 SoftGate.
A31003-H3160-S104-8-7620, 07/2014
Figure 142 Secure IP connectivity for remote subscribers - Sample generation
Configuration steps
The following steps have to be performed following installation of the HiPath 4000
SoftGate:
1. Configure the HiPath 4000 SoftGate's WAN interface via the Web Based
Management (WBM)
HiPath 4000 SoftGate WBM > Configuration > WAN > Settings
Bild 143 Secure Remote Subscriber - HiPath 4000 SoftGate WAN

settings
– Select a WAN interface (e.g. eth1). Apply the settings and then restart
HiPath 4000 SoftGate with the Restart button in the WBM.
HINWEIS: If the WAN interface is to be configured later, as described in

point 3, via AMO STMIB, then the restart from the WBM can be
relinquished. The necessary EXEC-
USSU:UPDATAP,<LTU_of_HiPath4000_SoftGate>; command
essentially leads to a full HiPath 4000 SoftGate reset.
A31003-H3160-S104-8-7620, 07/2014
– If the Picture CLIP (see Chapter 14, “Picture CLIP”) feature is required for
subscribers in the remote office, it can be activated here. In this case, the
required TCP Port 443 on the WAN interface is opened, though explicitly
for this feature. The WBM is furthermore not accessible via the WAN
interface as a result.
– If gatekeeper redundancy for HFA subscribers is required, this must

likewise be configured (see Chapter 9, “Gatekeeper Redundancy for HFA
Subscriber”).
2. An SPE certificate has to be imported for the WAN interface of the HiPath
4000 SoftGate.
HiPath 4000 SoftGate WBM > Configuration > WAN > SPE > Import
Keycert
Bild 144 Secure Remote Subscriber - HiPath 4000 SoftGate SPE

certificate
– The Load a SPE Key Certificate via HTPP screen is displayed.

Enter the decryption password and then search for the SPE certificate.
Press View Fingerprint of Certificate. Now import the certificate with the
Import Certificate from File button.
– The file containing the SPE certificate originates either from a customer-
defined PKI certification authority (RA/CA) or (if not available to the
customer) can be generated with the HiPath 4000 Assistant. See
documentation Signaling and Payload Encryption > Chapter 5,
“Generation SPE Certificates with HiPath 4000 Assistant”. The SPE
certificate must be available in PEM or PKCS#12 format.
3. Generate the WAN interface with AMO STMIB (IP address, netmask and
default router).
WAN interface data:
AMO STMIB is extended with the following parameters in a new WANIF
branch:
WIPADR=<ip address>, WNETMASK=<ip address>, WVLAN=<YES/NO>,
WVLANID=<number>, WDEFRT=<ip address>
Example:
CHANGE-
STMIB:MTYPE=NCUI2,LTU=20,TYPE=WANIF,WIPADR=220.20.20.98,WNETM
ASK=255.255.255.248,WVLAN=NEIN,WVLANID=0,WDEFRT=220.20.20.97;
A31003-H3160-S104-8-7620, 07/2014
WANIF WAN interface

WIPADR IP address of WAN interface
WNETMASK Netmask of WAN interface
WVLAN VLAN tagging of WAN interface (YES/NO)
WVLANID Virtual LAN ID of WAN interface
WDEFRT IP address of the default router in the WAN segment
After changing these parameters,

EXEC-USSU:MODE=UPDATAP,LTU=<LTU_of_HiPath4000_SoftGate>;
of the HiPath 4000 SoftGate must be performed. The HiPath 4000 SoftGate
is reset and the changes will be activated.
WAN feature data:
AMO STMIB is extended with the following parameters in a new WANFD
branch:
WUDPPRTL=<number>, WUDPPRTH=<number>, WTOSPL=<string>,
WTOSSIGN=<string>, WTLSP=<number>
Example:
CHANGE-
STMIB:MTYPE=NCUI2,LTU=20,TYPE=WANFD,WUDPPRTL=29100,WUDPPRTH=3
0099,WTOSPL="184",WTOSSIGN="104",WTLSP=4061;
WANFD Feature data of the WAN interface

WUDPPRTL Lower limit for the released UDP port range
WUDPPRTH Upper limit for the released UDP port range
WTOSPL TOS, Payload outgoing WAN for HFA
WTOSSIGN TOS, DiffServ Code Point for HFA signaling
WTLSP HFA TLSP port
The HiPath 4000 SoftGate itself does not have to be reset if these parameters
are changed, rather the data is activated as soon as the AMO has made the
changes.
WTOSSIGN TOS, DiffServ code point for HFA signaling

WTLSP HFA TLSP port
After changing these parameters,

RES-USSU:LTU,<LTU_of_HiPath4000_SoftGate>;
A31003-H3160-S104-8-7620, 07/2014
of the HiPath 4000 SoftGate must be performed. The HiPath 4000 SoftGate
is reset fully and the changes are activated.
HINWEIS: The default UDP port range of 1000 open ports (Default = 29100-
30099) can be restricted. It must be noted here that two UDP ports must be
available for each HFA terminal in the remote office. If no UDP port is
available at call setup, the HFA terminal is reset with an L1 error. So-called
overbooking is not supported.
4. Generate the phone for the remote office with AMO SBCSU.
IMPORTANT: An IP password has to be configured in AMO SBCSU:
5. Configure the phone for the remote office via its own menu.
The following settings have to be entered in the phone's menu:
– Gateway IP address (=WAN IP address of the HiPAth 4000 SoftGate)
– Station number (AMO SBCSU)
– IP password (AMO SBCSU)
– Transport mode: TLS
– NTP server
The address of an NTP server pool (z. B. 0.de.pool.ntp.org) should be
entered as the NTP address. The phone then always gets a list of active
NTP servers.
Use of a server pool requires the availability of a DNS server in order to
resolve the DNS name. If the phones are connected with the default
routers via DHCP, the DNS is usually entered automatically and the name
can be resolved. If, however, the OpenStage phone in the remote office
is assigned a static IP address, the DNS also has to be entered.
For the time change from daylight saving time to standard time, please
change Timezone offset (hours) from 2 to 1 on the phone.
Service Menu > Admin > ok > (Password = 123456) ok > Date and
time > ok > Time source > ok > (Time source = SNTP, SNTP IP = <ip
address of the NTP server pool or of the NTP server>, Timezone offset
(hours) = 1 ) > Save & exit > ok
– optional: DLS IP address
A31003-H3160-S104-8-7620, 07/2014
SoftGate_18_picture_clip.fm
Picture CLIP
Feature Description
14 Picture CLIP

The feature “PIcture CLIP” provides the option of showing centrally stored contact
data (name and picture) of the remote telephone party on an IP phone’s display
during the call.
In order to display centrally stored contact data, the OpenStage phones request
the data from a HiPath 4000 SoftGate, which then forwards the request to a
central directory server, retrieves the data and makes it available to the
OpenStage phones.
The display format (positioning, style, size etc.) of the contact data remains the
same as for local phonebook lookup, since the same mechanisms are used.
The directory server is queried for all numbers. If an entry for the number is found
on the LDAP directory server, the name and picture from the directory server are
displayed. If there is no entry for the number in the directory server, the name from
the local phonebook is displayed.
NOTE: In the case of an outgoing call from the phone, the picture for the called
contact is not shown, because the call icon (e.g. free, busy, forwarding symbol,
etc.) must be displayed in this case.
Two different modes for picture retrieval are currently supported:
Direct picture retrieval:
Preconditions:
• Direct picture retrieval configured.
• Contact data with picture stored on LDAP server.
=> The user sees the name and picture of the remote party as stored in the LDAP
directory.
The OpenStage phone performs a lookup on the HiPath 4000 SoftGate. The
HiPath 4000 SoftGate forwards the request to the LDAP server and receives the
name and picture of the requested phone number in return. The name and picture
are then forwarded together by the HiPath 4000 SoftGate to the OpenStage
phone and shown on the display.
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Service Information
Indirect picture retrieval:
Preconditions:
• Indirect picture retrieval configured.
• Contact data stored on LDAP server with valid reference to a picture stored
on another web server.
=> The user sees the name of the remote party as stored in the LDAP directory
and the picture as stored on the web server.
The OpenStage phone performs a lookup on the HiPath 4000 SoftGate. The
HiPath 4000 SoftGate forwards the request to the LDAP server and receives the
name and an URL of the web server with the relevant photo ID where the picture
is stored. In the next step, the HiPath 4000 SoftGate receives the picture on the
basis of the previously received URL and photo ID. The name and picture are
then forwarded together by the HiPath 4000 SoftGate to the OpenStage phone
and shown on the display.

• This feature is supported as of HiPath 4000 V6 R2 for HiPath 4000 SoftGate
and HiPath Access 500.
• If no picture is available, only the name and number from the LDAP directory
entry are displayed.
• If the LDAP directory server is not available, the PBX name is displayed after
a timeout.
• Only OpenStage 60/80 HFA support this feature.
• The OpenStage phones have to be able to access the HiPath 4000 SoftGate
or HiPath Access 500, which is configured for Picture CLIP. The OpenStage
phones therefore do not necessarily have to be configured on the respective
HiPath 4000 SoftGate or HiPath Access 500.
• The OpenStage phones only accept pictures encoded in jpg and of max. 50k
in size.
• An LDAP directory server is required for central storage of the contact data
and pictures. A web server is needed additionally for indirect picture retrieval.
• The contact data is stored on the LDAP directory server using the keys that
were configured on the HiPath 4000 SoftGate via WBM.
• It is recommended that the telephone numbers are stored in a fully qualified

format including country code and area code (e.g. 4989700754321). If the
numbers are stored using separators such as brackets, dashes or plus signs
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
(e.g. +49 (89) 7007-54321), then the LDAP directory server has to apply
conversion rules when checking for a match. The OpenStage phone issues
an LDAP query using plain digits without separators.
• The contact data from the LDAP directory server is only shown in some cases
after a short delay, because a secure connection has to be established to the
HiPath 4000 SoftGate via https. During this time, the display entry provided
by the HiPath 4000 system may become visible briefly. In indirect retrieval
mode, a further request/response cycle is needed to retrieve the picture.
14.3.1 HiPath 4000 SoftGate configuration

The HiPath 4000 SoftGate configuration provides the information needed to
access the LDAP directory server. It must be possible to access the LDAP
directory server from the HiPath 4000 SoftGate via IP.
The configuration of the HiPath 4000 SoftGate is performed via WBM.
Configuration > Picture CLIP
• Direct picture retrieval:
Figure 145 Direct picture retrieval configuration in HiPath 4000 SoftGate
• Indirect picture retrieval:
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Figure 146 Indirect picture retrieval configuration in HiPath 4000 SoftGate
IMPORTANT: The configured entries in the Picture CLIP Settings must corre-
spond to the entries on the LDAP directory server.
The fields Picture (for direct picture retrieval) and Filename of Picture (for
indirect picture retrieval) contain the matching keys on the LDAP directory server
for the picture that is to be displayed.
For more information on the LDAP configuration, please refer to LDAP directory
server configuration.
14.3.2 Phone Configuration

The phone configuration provides information needed in order to access the
HiPath 4000 SoftGate as well as information about the mode of operation.
The configuration can either be performed via the local phone menu, the Web
interface (WBM) or via the OpenScape Deployment Service (DLS).
Configuration via the phone menu

Admin > Applications >XML applications > Add application
This is basically the data for connectivity to the server hosting the feature (usually
HiPath 4000 SoftGate) and the mode of operation.
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
• Display name:
Name of the application displayed on the application tab of the phone's
display. Enter ldap.
• Application name:
Used internally to identify the XML application running on the phone. Enter
ldap.
• Server address:
The IP address of the HiPath 4000 SoftGate (e.g. 172.29.136.224).
• Server port:
The number of the http port used by the server to provide the XML documents
for the application. Varies according to the protocol configured, but HiPath
4000 SoftGate only allows 443.
• Protocol:
The protocol used for communication with the server. Choose https, because
HiPath 4000 SoftGate only allows https.
• Program name:
Enter ldap.
• Use proxy:
Must be set to No.
NOTE: None of the other configuration items is currently evaluated for the
feature.
IMPORTANT: If the feature is to be deactivated, the LDAP settings should be

deleted.
Phone canonical settings

For retrieval of contact data from the LDAP directory server, the remote telephone
number is converted according to the canonical dial settings (Admin > Local
functions > Locality > Canonical settings) when a call arrives. The format of
the resulting number should match the format the numbers are stored under on
the LDAP directory server. It is recommended to convert the numbers to fully
qualified format, i.e. adding country and area code to the subscriber number. This
ensures that the number used for lookup is unique.
Example:
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Figure 147 Canonical dial settings for picture retrieval

Phone configuration via OpenScape Deployment Service
IP Devices > IP Phone Konfiguration > Applikationen
Figure 148 Picture retrieval configuration via DLS
Tab XML Applikationen:
• Name der Applikation:

Enter ldap.
• Display Name:
Enter ldap.
• Programm-Name:
Enter ldap.
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
• Server Adresse:
Enter the IP address of the HiPath 4000 SoftGate.
• Server Port:
Enter the server port of the HiPath 4000 SoftGate.
• Transport:
Select http or https. HiPath 4000 Softgate only supports https.
14.3.3 LDAP directory server configuration

The LDAP directory server must offer an LDAP V2 or V3 interface and provide
access using password-based, so-called "simple" security.
The contact data is stored on the LDAP directory server using the keys that were
configured on the HiPath 4000 SoftGate via WBM.
It is recommended that the telephone numbers are stored in a fully qualified

format including country code and area code (e.g. 4989700754321). If the
numbers are stored using separators such as brackets, dashes or plus signs (e.g.
+49 (89) 7007-54321), then the LDAP directory server has to apply conversion
rules when checking for a match. The OpenStage phone issues an LDAP query
using plain digits without separators.
Example of an LDAP structure:
The entries in the attribute type column marked red must be provided to the
HiPath 4000 SoftGate via the WBM configuration (see HiPath 4000 SoftGate
configuration).
Figure 149 LDAP server - HiPath 4000 SoftGate data
The screenshot below looks at the nodes where the telephone contact data is
found.
The base node for searching is selected with o=scd.
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Figure 150 LDAP server - Telephone contact data
Another example using a different LDAP directory server in direct mode:
Figure 151 LDAP server - Example of direct picture retrieval (01)
As can be seen, the node structure in this server is very simple. The base node
is selected with ou=system.
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Figure 152 LDAP server - Example of direct picture retrieval (02)
14.3.4 Testing LDAP access

It is possible from HiPath 4000 V6 R2.15 to use the HiPath 4000 SoftGate WBM
to verify whether LDAP server access is properly configured.
To do this, select the Picture Clip > Test function is the Configuration menu.
Figure 153 Launching the LDAP server access test
Now click the In separatem Fenster Öffnen/Open in separate window button.
Figure 154 Searching for phone numbers using the LDAP server
A31003-H3160-S104-8-7620, 07/2014
Picture CLIP
Enter a phone number and click Ok.
Figure 155 Correctly configured LDAP
If LDAP server access has been correctly configured and if an entry exists for the
phone number in the LDAP directory, a "result" is displayed at the lower margin.
The last and first name can be identified. The subsequent characters indicate that
a picture is also available.
If LDAP server access is not configured correctly, a unique error message is

issued.
Example:
Figure 156 Incorrectly configured LDAP
It can therefore be verified that the parameters are correct as soon as the LDAP
server configuration has been performed.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_19_mfcr2.fm
MFC-R2
Feature Description
15 MFC-R2

MFC/R2 is a telephony signaling protocol which is used to provide signaling
between switches. Signaling can be done over analog (TMxxx) or digital (DIUx)
trunks with CAS (channel associated signaling).
MFC-R2 signals are provided from vSIUX2. SIUX functionality has been
introduced as virtual board for HiPath 4000 SoftGate/HiPath Access 500.
Figure 157 MFC-R2
For more details about MFC-R2, please refer to the service documentation:
HiPath 4000 V6, Section 3 - Feature Usage Examples > Networking > MFC-
R2 Signaling

As of HiPath 4000 V6 R2 MFC-R2 is supported with HiPath 4000 SoftGate/
HiPath Access.

The digital MFC-R2 line signaling version described by ITU-T Q.400-Q490 can be
configured in HiPath Access with the HiPath Access PRI module.
A31003-H3160-S104-8-7620, 07/2014
MFC-R2
The DIUT board must be configured in E1/CAS functionality (FCTID=2), for

example
ADD-BCSU:MTYPE=DIU,LTG=1,LTU=19,SLOT=3,PARTNO="Q2335-
X",LWVAR=0,FCTID=2,HWYBDL=A,ALARMNO=0,MACADDR=00-1A-E8-32-60-
5E,TDMLAW=0;
Additionally, a vSIUX2 must be configured. Configuration of vSIUX2 is the same
as for standard SIUX2 boards. MFC-R2 functionality is selected by configuring
the Q2187-X function ID3. Within the ID3 function, vSIUX only provides a MFC
subset of R2, i.e. MFC-R2 forward and backward functionality (other MFC
variants such as R1, SOCOTEL or MFP are not supported).
Depending on the configuration, you can set up a maximum of 8 MFC-R2 signal

receivers and MFC signal transmitters on this. These always operate in pairs and
the configuration is also always in pairs, for example
ADD-BCSU:MTYPE=SIUP,LTG=1,LTU=19,SLOT=5,PARTNO="Q2187-X",
MFCTYPE=R2B&R2B&R2F&R2F&R2F&R2F&R2F&R2F,LWVAR=0,FCTID=3;
is the configuration for 2 backward signal transmitters (which includes 2 forward
receivers) and 6 forward transmitters (which includes 6 backward receivers).
Other SIUX functionality (e.g. DTMF, ANI,…) is not implemented in vSIUX2. If it

is configured by AMO, the board remains unavailable.
IMPORTANT: Initialization can be performed in an active system but will only be

activated when the shelf has been reloaded (AMO USSU). There is no indication
from AMO BCSU that a restart has to be performed.
Initialization of MFC signals

A default initialization of MFC signals (frequency and attenuation) is performed in
vSIUX2 code. The frequency of all signals is defined according to Q.441 of ITU-
T Q.400-Q490, attenuation is set to -8dBm0.
It is possible for national applications to provide special signal definitions by

means of special initialization files. By default there are three different files on the
system's hard disk.
• APSP/LTG/LG25/PZJSMFD0 is the initialization file for default signals, A-law
• APSP/LTG/LG25/PZJSMFD1 is the initialization file for default signals, µ-law
• APSP/LTG/LG25/PZJSMFD2 is the initialization file for signals for Brazil (A-

law, -13dmB0)
The initialization file can be selected by AMO ZAND, for example

CHANGE-ZAND:TYPE=SIUXPER,LEVMFC=2; for Brazil
Initialization file 0 is selected by default. In addition to the signal description, the

file also indicates which HWY/TSL is to be used for which line on SIUX.
A31003-H3160-S104-8-7620, 07/2014
MFC-R2
A31003-H3160-S104-8-7620, 07/2014
MFC-R2
A31003-H3160-S104-8-7620, 07/2014
SoftGate_20_vslc.fm
HiPath Cordless E Integration
16 HiPath Cordless E Integration

vSLC is supported for HiPath 4000 SoftGate as of HiPath 4000 V6 R2 in
preparation for the HiPath Cordless E integration in HiPath 4000 V7.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_20_vslc.fm
HiPath Cordless E Integration
A31003-H3160-S104-8-7620, 07/2014
SoftGate_21_wbm.fm
WBMs of the Boards
17 WBMs of the Boards

For a description of the grafical user interface of the WBMs for vHG 3500 HFA,
vHG 3500 SIP and vHG 3575 please refer to the following links.
vHG 3500 HFA:
vHG 3500 SIP:
vHG 3575:
IMPORTANT: These documents are as online help part of the WBM.
A31003-H3160-S104-8-7620, 07/2014
SoftGate_21_wbm.fm
WBMs of the Boards
A31003-H3160-S104-8-7620, 07/2014
lan_interfaces_01.fm
Feature Description
Separate LAN Connectivity for Administration and VoIP

The feature "Separate LAN Connectivity for Administration and VoIP" is
supported as of HiPath 4000 V6 R2.
1 Feature Description
The Voice LAN can be split fully from the Management LAN with the introduction
of this feature. Before it was only possible to split the IPDA LAN from the
Customer LAN.
If you want to separate the Management LAN from the Voice LAN, you have to
enter an IP address for the Management LAN.
If an IP address is entered for the Management LAN, HiPath 4000 Assistant will
use it to connect to the gateway WBM and reaches it via the Customer LAN
interface. If the IP address has the default value 0.0.0.0, HiPath 4000 Assistant
will use the IP address of the IPDA LAN.
Separation of the two interfaces can be configured via the gateway.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
A31003-H3160-S104-8-7620, 07/2014
Service Information
2 Service Information
• This feature is implemented with HiPath 4000 V6 R2.
• This feature is supported for HiPath 4000 SoftGate, HG 3575 and HG 3500.
• The Management LAN interface data is provided for each HiPath 4000
SoftGate, HG 3575 and HG 3500. It consists of IP address, netmask, default
gateway, vLan tag and vLan ID.
• If a vHG 3500 is configured in a HiPath 4000 SoftGate, the Management LAN

interface data is taken from the board data of the HiPath 4000 SoftGate. This
means that this data is not configurable with AMO CGWB for vHG 3500.
A31003-H3160-S104-8-7620, 07/2014
Service Information
A31003-H3160-S104-8-7620, 07/2014
3 Generation (Example)
Management LAN data for
• HiPath 4000 SoftGate, HG 3575: AMO STMIB
• HG 3500: AMO CGWB
Use branch MANLANIF in AMO STMIB and AMO CGWB with the following
parameters:
MIPADR=<number>, MNETMASK=<number>, MVLAN=<param>,
MVLANID=<number>, MDEFRT=<number>
If these parameters are changed, the boards must be reset to get the changed
data.
In WBM the Ethernet interface to be used as Management LAN is assigned.
• HG 3500/3575
WBM > Wizard > Initial Setup
The mask for Gateway Properties is displayed. In the dialog for Operation
Mode : Management-LAN the Ethernet interface can be assigned.
• vHG 3575
WBM > Configuration > Management Interface
Figure 1 Management LAN Interface at HiPath 4000 SoftGate
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs
4 Relevant AMOs
AMO Parameter Sprache/ Beschreibung/ Discription

Language
CGWB/ MIPADR d IP Adresse der CGW Baugruppe (Source
STMIB Adresse)
MIPADR e Source IP address of CGW board
MNETMASK d IP-Netzmaske des LAN-Segmentes Die IP-
Netz- und Host-Teil in der IP-Adresse. Alle
IP-Adressen am LAN-Segment müssen
bzgl. des Netzanteils der IP-Adresse gleich
und bzgl. des Host-Teils unterschiedlich
sein (auch der Default Router muss dieser
Bedingung entsprechen).
MNETMASK e IP net mask of LAN segment The IP net
mask determines the network and the host
partition of an IP address. All IP addresses
of a LAN segment must contain the identical
network addresss part but different host
address parts (also the Default Router must
fulfill this requirement).
MVLAN d Virtuelles LAN
MVLAN e VLAN tagging on LAN-IF
MVLANID d Identifikations-Nummer des virtuellen LAN
Spezielle Einstellungen werden von einigen
LAN-Einrichtungen (Router...) gefordert,
ansonsten ist 0 der übliche Wert
(Standardwert)
MVLANID e Virtual LAN Identification
Special settings are required by certain LAN
equipment (routers...), in other cases the
VLAN Id should be set to 0 (default)
MDEFRT d IP-Adresse des Default Routers innerhalb
des LAN-Segmentes
Der Default Router übernimmt die
Weiterleitung der Pakete, die eine
Zieladresse außerhalb des eigenen LAN-
Segmentes haben.
0.0.0.0 bedeutet, dass kein Default Router
konfiguriert ist.
MDEFRT e IP address of the default router within the
LAN segment
The default router takes care of routing
forward all packets with a destination
address with a network part different from
the own LAN segment.
0.0.0.0 means that no default router is
configured.
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
hipath_access.fm
HiPath Access
HiPath Access
HiPath Access is based on hardware and software of HiPath 4000 V6. It offers a
cost-saving alternative for branch office solutions with integrated PSTN
connection.
For documentation on HiPath Access please refer to the following manual:

HiPath Access, Service Documentation
A31003-H3160-S104-8-7620, 07/2014
hipath_access.fm
HiPath Access
A31003-H3160-S104-8-7620, 07/2014
rg_8300.fm
RG 8300 V6
RG 8300 V6
The SIP gateway RG 8300 enables IP connections with SIP-Q to OpenScape
Voice and ISDN T1 or E1 PRI connections to PSTN or Hicom 300 / HiPath 4000
systems.
It is based on the hardware and software of HiPath 4000.
For documentation on RG 8300 please refer to the following manuals:
• Configuration and features

RG 8300 V6, Service Documentation
• Feature description
HiPath 4000 V6, Feature Description
A31003-H3160-S104-8-7620, 07/2014
rg_8300.fm
RG 8300 V6
A31003-H3160-S104-8-7620, 07/2014
rg_8350a.fm
RG 8350 A
RG 8350 A
The SIP gateway RG 8350a enables IP connections with SIP-Q to OpenScape
Voice and ISDN T1 or E1 PRI connections to PSTN or Hicom 300 / HiPath 4000
systems.
It is based on the hardware and software of HiPath 4000.
For documentation on RG 8350a please refer to the following manuals:
• Configuration and features

RG 8350a V6, Service Documentation
• Feature description
HiPath 4000 V6, Feature Description
A31003-H3160-S104-8-7620, 07/2014
rg_8350a.fm
RG 8350 A
A31003-H3160-S104-8-7620, 07/2014
legk_01_general_info.fm
General Information
Large Enterprise Gatekeeper (LEGK)
Large Enterprise Gatekeeper (LEGK)
1 General Information
1.1 Overview
The feature “Large Enterprise Gatekeeper (LEGK)” is part of the call processing
software and has a gatekeeper function. Therefore the IP address resolution
mechanism (gatekeeper function) for IP trunking is switchable in all network
nodes.
For this function the STMI2/4 (HG 3500) board as hardware is required.
SIP-Protocol is used by default for trunking.
Node 3
Node 2 HiPath 4000
HiP
ath
HG 3500 Node 4
0
HG
40
400
00
350
ath
0
350
HiP
HG
IP Network
0 HG HiP
Node 1 350 350 ath
HG 40
0
00 00
h 40
at
HiP Node 5
Figure 1 Example: IP trunking in an HiPath 4000 networked system. LEGK is

active in each node.
A31003-H3160-S104-8-7620, 07/2014
General Information
Gatekeeper Function
1.2 Gatekeeper Function

The Gatekeeper function is used to allocate the IP address of a destination
gateway to a dialed extension (IP address resolution). The Large Enterprise
Gatekeeper (LEGK) performs this function using a HG 3500.
The gatekeeper functionality (LEGK) is fully integrated in the LCR function in

HiPath 4000. The LEGK is therefore neither an external server nor a host in the
IP network. The LEGK is a process within the HiPath 4000 call processing
software. The Gatekeeper function is consequently fully configured using AMO
commands. The Web Based Management (WBM) tool in HG 3500 is only needed
for special settings, for example, codec selection and QoS. With the HG 3500
Common Gateway these features are also configurable via AMO - the WBM is
now almost exclusively used for maintenance tasks.
If IP trunking is used in a purely HiPath 4000 networked system, then all HG 3500
gateways connected must use the LEGK of their respective nodes. HG 3500s
may not register with the LEGK of another node.
1.2.2 Key words
1.2.2.1 Local Gateway
This is the name given to an HG 3500 configured for trunking in an HiPath 4000
with a gatekeeper, which it uses for address resolution.
With regard to the Bild 1 all HG 3500 Gateways displayed there are local
Gateways.
1.2.2.2 Remote Gateway
This is the name given to an HG 3500 configured for trunking in an HiPath 4000,
which registers with another, external gatekeeper or registry for address
resolution.
Only HG 3500 gateways that are not HiPath 4000s, e.g. OpenScape Voice or an
Internet Service Provider, may register as remote gateways with the system.
A31003-H3160-S104-8-7620, 07/2014
General Information
Gatekeeper Restrictions
1.2.2.3 IP Address Resolution
A called party number is routed via LCR to an IP address in the destination

gateway. IP Address Resolution may be configured in an HiPath 4000 with LCR.
This service is only available for local gateways.
1.3 Gatekeeper Restrictions

The Large Enterprise Gatekeeper can be operated together with the board HG
3500.
Maximum configuration:
An IP trunking network using HG 3500 is theoretically limited to a maximum of
9999 trunking boards (DIMSU). For the exact maximum, please refer to the
release notes and/or technical specifications.
A31003-H3160-S104-8-7620, 07/2014
General Information
Gatekeeper Restrictions
A31003-H3160-S104-8-7620, 07/2014
legk_02_inst_ip_feature.fm
Guidelines for Installing an IP Feature
2 Guidelines for Installing an IP Feature

• Diagram of the customer IP network
• Create an HiPath 4000 network plan with all gateways, access points, HFA
terminals
• Define the number of LEGKs and HG 3500 gateways required
• Map the HiPath 4000 network plan to the customer IP network
• Perform network analysis with the help of the IP service tool to determine the
network’s VoIP capability.
• Confirm the feasibility of the IP components planned
A31003-H3160-S104-8-7620, 07/2014
legk_02_inst_ip_feature.fm
Guidelines for Installing an IP Feature
A31003-H3160-S104-8-7620, 07/2014
legk_04_configuration.fm
Configuring the Feature
3 Configuring the Feature

The Large Enterprise Gatekeeper (LEGK) is a feature for IP trunking address
resolution for data transfer in IP networks. The configuration of this feature is
broken down into the following steps which are to be performed in consecutive
sequence:
• Configuration: Database flexama memory - Section 3.4, “Configuring the

FLEXAMA Memory in the Database”, on page 473
• Configuration: HG 3500 - Section 3.5, “Configuring a HG 3500 on the LAN

Segment”, on page 477
• Configuration: HG 3500 directory numbers - Section 3.6, “Configuring the HG

3500 Directory Number”, on page 495
• Configuration: LCR digit analysis - Section 3.7, “Configuring IP Trunking in

the LCR”, on page 497
• Configuration: Subscriber, trunk and tie trunk connections in the local switch
- Section 3.8, “Configuring Circuits and Terminals”, on page 503
The LEGK feature must be taken into consideration when configuring IP trunking.
If IP trunking is already available, it must be re-generated.
The following sections contain configuration examples and detailed explanations

of all requisite AMOs and AMO parameters. A distinction is made between
configuration with HiPath 4000 Assistant/Manager (Configuration

Manager) or
AMO-based configuration.
The Large Enterprise Gatekeeper can be implemented in all HiPath 4000 system
configurations. An LEGK can either be implemented in all nodes or in a single
node in an HiPath 4000 network.
IMPORTANT: Registration of remote HG3500 gateways at HiPath 4000 Large

Enterprise Gatekeeper is not supported. Remaining solutions are the local regis-
tration with Large Enterprise Gatekeeper and HiPath OpenExchange Solution.
A31003-H3160-S104-8-7620, 07/2014
Sequence of Generation
3.2 Sequence of Generation

This section describes the basic sequence for generating the “Large Enterprise
Gatekeeper“ feature. This description focuses first and foremost on the AMOs
that were extended for the purpose of administering the feature. These AMOs are
shown in bold typeface.
The other AMOs displayed are also involved in the generation process but were
not extended for the specific feature. The existing generation sequence is used
here.
In the course of configuration, the AMOs GKREG and GKTOP do not check if the
resources used, such as sectors, sector path, clusters, LCR dial plan numbers,
node numbers, external gateways, etc. are already configured.
The user is responsible for the consistency of the IP network’s administered

topology resources (for example, bandwidth, B-channels, etc.). This task is not
supported by the AMO GKTOP with plausibility checks.
DIMSU BFDAT BCSU CGWB GKREG

ZANDE ZAND GKTOP
WABE SIPCO
BUEND TACSU RICHT LDAT LDPLN
TDCS LODR
COT
TSCS
COP
SBCS
COSSU
SDAT
ACSU
IMPORTANT: The AMOs do not check the specified gatekeeper configuration

data for plausibility or network-wide consistency. This is one of the technician’s
network planning tasks.
3.3 Activating the Large Enterprise Gatekeeper

This step is only necessary if you do not want to run a Large Enterprise
Gatekeeper for least cost routing on the local HiPath 4000 system. The feature is
active by default.
A31003-H3160-S104-8-7620, 07/2014
Activating the Large Enterprise Gatekeeper
If you do not want a gatekeeper at the local HiPath 4000 system, then the feature
must be deactivated in the system before HG 3500 is installed. The GATEKPR
parameter in the AMO ZANDE is used for this.
IMPORTANT: You cannot enable or disable the gatekeeper function at an HiPath

4000 system by simply activating or deactivating the AMO ZANDE once HG 3500
generation is complete.

Instead, you must remove all STMI2/4 HG 3500 boards, activate/deactivate the
ZANDE parameter, and finally reinstall the boards. This sequence is necessitated
by the different configurations of feature-specific data.
Generation
AMO ZANDE
The AMO ZANDE is used on every HiPath 4000 system to specify whether or not
this feature should be used.
Configuration with the AMO ZANDE can only be executed in expert mode.
Expert Mode > HiPath 4000 Expert Access --> Open ...<IP> with AMO 
(see AMO command)
ADD-ZANDE:TYPE=ALLDATA,GATEKPR=YES;
This command specifies that the LEGK address resolution function (AMO
GKREG) should be operated and administered at the local HiPath 4000
system.

Language
ZANDE GATEKPR d Gatekeeper Konfigurierung
Diese Parameter muss auf NEIN gesetzt werden
wenn eine PBX ohne Gatekeeper betrieben
werden soll. Standardmäßig wird JA, d.h. also ein
Gatekeeper wird an der lokalen PBX betrieben,
eingerichtet.
GATEKPT e Gatekeeper configuration
This Parameter must be set to NO when a PBX
has to operate with-out a gatekeeper. Default
value is YES, that means a gatekeeper will be
configured on the local PBX.
Table 1 AMO ZANDE parameters in the CHANGE branch under

TYPE=ALLDATA
A31003-H3160-S104-8-7620, 07/2014
Activating the Large Enterprise Gatekeeper
Display
Displaying with the AMO ZANDE can only be executed in expert mode.
Expert Mode > HiPath 4000 Expert Access > Open
...<IP> with AMO
(see AMO command)
DISPLAY-ZANDE:TYPE=ALLDATA;
Use this command to output all central parameters in the ALLDATA branch,
including the gatekeeper parameter.
A31003-H3160-S104-8-7620, 07/2014
Configuring the FLEXAMA Memory in the Database
3.4 Configuring the FLEXAMA Memory in the Database

First of all, a certain volume of feature-specific memory should be provided. You
can only start to configure the gatekeeper data after this memory has been
created with the AMO DIMSU.
The values specified with ADD-DIMSU become effective immediately.
3.4.1 Number of Internal and External Gateways

This step is used to configure a table containing general administrative data for
all internal and external gateways in the network. An entry is required for each
gateway.
IMPORTANT: You can skip this section if there is no gatekeeper configured at

the local HiPath 4000 system (AMO ZANDE: GATEKPR=NO).
Add:
ADD-DIMSU:TYPE=SYSTEM,GWREG=25;
Use this command to set the number of network-based gateways (in our case 25)
that can address the Large Enterprise Gatekeeper.
Display:
DISPLAY-DIMSU:TYPE=SYSTEM;
Use this command to output all system parameters including the number of
gateways permitted.
DISPLAY-DIMSU:TYPE=ALL,PARAM=GWREG;
Use this command to output only the number of gateways permitted.
A31003-H3160-S104-8-7620, 07/2014
3.4.2 Number of Internal HG 3500 Gateways in a

System
This step is used to configure a table containing data for the internal gateways in
every HiPath 4000 system. An entry is required for each gateway.
Add:
Use this command to set the maximum number of HG 3500 (in our case, 6).
Display:
DISPLAY-DIMSU:TYPE=SYSTEM;
Use this command to output all system parameters including the number of
internal gateways permitted.
DISPLAY-DIMSU:TYPE=ALL,PARAM=CGW;
Use this command to output only the number of internal gateways permitted.
3.4.3 Number of LCR Digit Patterns for Digit Pattern

Pools 1 through 8
This step configures the number of LCR digit patterns permitted in each of the
eight available digit pattern pools. Up to 64,000 digit patterns are permitted in
each pool. The digit patterns configured are evaluated during IP trunking as part
of least cost routing.

the local HiPath 4000 system (AMO ZANDE: GATEKPR=NO).
In this case, the default configuration is sufficient with LCR pool 1 and dial plan 0.
A31003-H3160-S104-8-7620, 07/2014
Add:
ADD-
DIMSU:TYPE=NETWORK,LDPLN1=50000,LDPLN2=12000,LDPLN4=5
600;
Use this command to set the maximum number of LCR digit patterns per digit
pattern pool, in our case:
• 50,000 digit patterns in digit pattern pool 1
Display:
DISPLAY-DIMSU:TYPE=NETWORK;
Use this command to output all parameters associated with network-wide

features, including the number of digit pattern schemes in digit pattern pools 1
through 8.
DISPLAY-DIMSU:TYPE=ALL,PARAM=LDPLN2;
Use this command to output only the number of LCR digit pattern schemes
permitted in pool 2.
3.4.4 Number of Cache Elements for Cache Pools 1

through 8
This step configures the number of cache elements permitted in each of the eight
available cache pools. Up to 6,400 cache elements are permitted in each pool.

the local HiPath 4000 system (AMO ZANDE: GATEKPR=NO).
Add:
ADD-
DIMSU:TYPE=NETWORK,LDPLN1=5000,LDPLN2=120,LDPLN4=100;
A31003-H3160-S104-8-7620, 07/2014
Use this command to set the maximum number of cache elements per digit
pattern pool, in our case:
• 120 digit patterns in digit pattern pool 2
• 100 digit patterns in digit pattern pool 4
Display:
DISPLAY-DIMSU:TYPE=NETWORK;
Use this command to output all parameters associated with network-wide

features, including the number of cache elements in cache pools 1 through 8.
DISPLAY-DIMSU:TYPE=ALL,PARAM=LDPLNC1;
Use this command to output only the number of cache elements permitted in
cache pool 1.
A31003-H3160-S104-8-7620, 07/2014
Configuring a HG 3500 on the LAN Segment
3.5 Configuring a HG 3500 on the LAN Segment

The HG 3500 module (STMI2/4) establishes the payload connections between
the central HiPath 4000 system and the HiPath 4000 LAN segment.
• HG 3500 boards may be implemented both in peripheral shelves (LTU 1-15)

in the central system and in access points (LTU 17-99). You can implement
the same number of HG 3500 gateways that you configured with the AMO
DIMSU (see Section 3.4.2, “Number of Internal HG 3500 Gateways in a
System”, on page 474).
• Multiple HG 3500 modules can be implemented in an HiPath 4000 system.
• All HG 3500 modules must be connected at the HiPath 4000 LAN segment.
• The HG 3500 hardware is the STMI2/4 board. This board can simultaneously
offer IP trunking, a WAML circuit, IPDA function, HFA function and SIP
subscriber function. The type and number of circuits or B channels available
in each case is set with the AMO BFDAT.
An HiPath 4000 LAN segment is that part of the customer network where the
central system’s IP components and directly connected (that is, not via router)
access points are installed.
3.5.1 Configuring the HG 3500 Gateway

You must first configure the local LAN segment. Next you must install each HG
3500 gateway.
3.5.1.1 Configuring the HG 3500 Board
The configuration example applies to the HiPath 4000 system with gatekeeper on
the left (“N 1“). The HG 3500 to be administered with the relevant configuration
data is colored yellow. The gatekeeper (CUSIP=192.168.2.11) in the partner
system “N 2“ is colored in a lighter shade of yellow and will be described in more
detail later in conjunction with the AMOs GKREG and GKTOP.
A31003-H3160-S104-8-7620, 07/2014
IP address: 192.168.1.11 Gateway ID: LOCGW001

STMI 2/4
PNNO: 10-69-300 Number of DMC connections: 8

HG GW directory number:
3500 354711 IPADDR
GW PEN: 1-3-91
GW sector: 301
HG GW LAN sector: 300 Def. router IP add: 192.168.1.254
3570
Peripheral
Boards
Ra
Router CUSIP
IP Networ k
H iPat h 4000 LAN segment
Atlantic LAN
ADP HiPath
4000
Rb N2
CC-A
Router
CC-B
CSTA
Assistant
HiPath
4000
N1
Figure 2 Configuring a HG 3500 gateway
ADD-BFDAT: FCTBLK=1, FUNCTION=HG3550,

BRDBCHL=BCHL60&BCHL120;
CHANGE-BFDAT: CONFIG=CONT, FCTBLK=1,
FUNCTION=HG3550, LINECNT=1,
UNITS=3;
CHANGE-BFDAT: CONFIG=OK, FCTBLK=1,
ANSW=YES;
A31003-H3160-S104-8-7620, 07/2014
ADD-BCSU: MTYPE=IPGW, LTG=1,

LTU=3, SLOT=91,
PARTNO=Q2316-X10, FCTID=1,
FCTBLK=1, BCHL3550=30;
ADD-CGWB: MTYPE=CGW, LTU=3,
SLOT=91, IPADR=192.168.1.11,
NETMASK=255.255.255.0;
CHANGE-CGWB: MTYPE=CGW, LTU=3,
SLOT=91, TYPE=GWDATA,
GWID1=LOCGW001;
SLOT=91, TYPE=LEGKDATA,
GWNO=3, GWDIRNO=354711;
SLOT=91, TYPE=DMCDATA,
DMCCONN=8;
SLOT=91, TYPE=GLOBIF,
DEFRT=192.168.1.254;
Generation
A HG 3500 board is configured via 3 AMOs: BFDAT, BCSU and CGWB.
AMO BFDAT
The configuration of the functional blocks for the HG 3500 board is done with the
AMO BFDAT.
Configuration Management --> System Data --> Board --> CGW

Function Block
Click New, enter data and click Save.
ADD-
BFDAT:FCTBLK=1,FUNCTION=HG3550,BRDBCHL=BCHL60&BCHL120
;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3550,
LINECNT=1,UNITS=3;
CHANGE-BFDAT=CONFIG=OK,FCTBLK=1,ANSW=YES;
A31003-H3160-S104-8-7620, 07/2014

Language
BFDAT ANTW d ANTW=JA
Block-Konfiguration abschließen
ANSW e ANSW=YES
Finish block configuration
ANZEINH d Anzahl der vordefinierten Blöcke mit
ausgewählter Funktion pro Satz.
UNITS e Defines the number of predefined blocks with the
selected function per line.
LINECNT e Defines the number of lines related to the selected
function.
BKANANZ d Block fuer Baugruppe mit 60 und/oder 120 B-
Kanälen
BRDBCHL e Dedicates the block for boards with 60 and/or 120
b-channels
CONFIG d CONFIG=WEITER
Weitere Block-Konfiguration möglich
CONFIG=OK
Block-Konfiguration abschließen
CONFIG e CONFIG=CONT
Continue block configuration
CONFIG=OK
Finish block configuration
welcher auf dem Common Gateway konfiguriert
werden soll. Anhand des Funktionsblocks wird die
Konfiguration der benötigten pyhsikalischen Lines
(Sätze der Baugruppe) festgelegt.
should be configured on the common gateway
board. With that index the amount of needed
physical lines (board circuits) is calculated.
FUNCTION d Dieser Parameter legt das Konfigurationsprofile
des CGW fest. Dabei muss die evtl. benötigte
HG3570 Funktion als erste angeführt werden.
Falls ein bestimmter Line-Bereich für die
Funktionen HG3530, HG3540 oder HG3550
vorreserviert werden soll, muss die
entsprechende Funktion am Ende stehen und mit
dem Wert HG35xxR abgeschlossen sein. Die
Funktion STANDBY kann nur als Einzel-Funktion
konfiguriert werden.
Table 2 AMO BFDAT parameters
A31003-H3160-S104-8-7620, 07/2014

Language
FUNCTION e This parameter defines the configuration profile of
the common gateway board. If HG3570
functionality is used, it must be configured at first
position. If a prereservation of a certain line range
of functions HG3530, HG3540 or HG3550 is
desired, this function must be at the end of the
profile just suffixed by the according HG35xxR
value. The function STANDBY can only be
Table 2 AMO BFDAT parameters
AMO BCSU
The modules are configured in the system and activated with the AMO BCSU.

Click New, enter data and Save.
X10,FCTID=1,FCTBLK=1,BCHL3550=30;
CHANGE-BCSU:TYPE=HWYBDL,LTU=3,SLOT=81,PARTNO=Q2316-
X10,HWYBDL=A;

Language
BCSU TYP d TYP=IPGW
Common Gateway Baugruppe
MTYPE e MTYPE=IPGW
Common gateway board
LTG d LTG-Nummer
Parameter kann entfallen - oder muss auf 1
gesetzt werden.
LTG e Line/Trunk Group Number
Parameter can be omitted - or must be set to 1.
LTU d LTU-Nummer des Rahmens, in dem die HG 3500
eingesetzt wird.
Die HG 3500 darf nur in den Rahmen des HiPath
4000 Zentralsystems (LTU 1..15) eingesetzt
werden. Der Rahmen muss mit einer LTUCX
Baugruppe ausgestattet sein.
LTU e Line/Trunk Unit Number of the shelf where the
HG 3500 is plugged.
An HG 3500 may only be used in a shelf of the
HiPath 4000 central system (LTU 1..15). The
shelf must be equipped with a LTUCX board.
Table 3 AMO BCSU parameters
A31003-H3160-S104-8-7620, 07/2014

Language
EBT d Einbauteilung des Steckplatzes der HG 3500
SLOT e Slot where the HG 3500 resides.
SACHNR d Sachnummer der HG 3500-Baugruppe
PARTNO e Part Number of the HG 3500 Board
FCTID d Function ID
FCTID e Function ID
FCTBLK d Function Block Index
FCTBLK e Function block index
BKAN3550 d Anzahl der B-Kanäle für die HG3550 Funktion
BCHL3550 e Amount of b-channels for HG3550 function
HWYBDL d Highway Bündel
Die HG 3500 / STMI2/4 Baugruppe unterstützt
die Wideband Technologie. Deshalb muss der
Baugruppe entweder das Highway Bündel A
(default) oder F zugewiesen werden.
HWYBDL e Highway bundle
The HG 3500 / STMI2/4 board supports
wideband technology. Thus either highway
bundle A (default) or F must be assigned to this
board.
Table 3 AMO BCSU parameters
AMO CGWB
Use the ADD branch to make the individual settings necessary for operating the
HG 3500 board. Global and Ethernet-specific board data is configured. This data
is not loaded to the board until the board is activated or deactivated and then re-
activated (RESTART-BSSU).
The CHANGE branch MTYPE=CGW allows you to set a number of parameters

that are located in different branches. Data from the branches TYPE=GWDATA,
TYPE=DMCDATA, and TYPE=LEGKDATA is also needed for startup.
The specification of a GWNO depends on the operating scenario set (see AMO
ZANDE)
• PBX with LEGK
• PBX without LEGK
Operation in mixed mode is not possible.
A gateway number is required if the gatekeeper is configured at the local PBX and
you want to register the gateway here.
A gateway number is not required if a gateway registers at a foreign PBX’s

gatekeeper. If entered, a gateway number would be ignored.
A31003-H3160-S104-8-7620, 07/2014
Adding Ethernet-specific board data

Make the settings on the STMI Board Data tab and Save.
Board Maintenance
with OK.
ADD-
CGWB:LTU=3,SLOT=91,IPADDR=192.168.1.11,NETMASK=255.25
5.255.0;
The HG 3500 must be restarted in order for this change to become
effective. Use
RESTART-BSSU:ADDRTYPE=PEN,LTU=3,SLOT=91;
IMPORTANT: Established connections are cleared down as a result!
A31003-H3160-S104-8-7620, 07/2014

Language
CGWB LTU d LTU-Nummer des Rahmens, in dem die HG 3500
gesteckt ist.
LTU e Line/Trunk Unit Number of the shelf where the HG
3500 is plugged.
IPADR d IP-Adresse der HG 3500 im Kunden LAN
Legt die IP-Adresse fest, über die ein HG 3500
Gateway am HiPath 4000 LAN-Segment erreicht
werden soll.
IPADR e IP-Address of HG 3500 on customer LAN
Assigns the address with which a HG 3500
gateway can be reached on the HiPath 4000
LAN-segment.
NETMASK d Netzmaske des LAN-Segmentes
NETMASK e Netmask of LAN-segment
MUSTER d Ruhebitmuster
Der Default-Wert ist 213 (dezimal)
PATTERN e Idle Pattern
Default value is 213 (decimal)
Table 4 AMO CGWB parameters
IMPORTANT: Before administering the ADD-CGWB command, use ping to check

that the gateway IP address given to you by the administrator is reachable.
CUSIP must not respond as this would indicate that the corresponding address
has already been assigned.
CUSIP must be set differently for every HG 3500. The AMO does not verify if this
rule is observed.
A31003-H3160-S104-8-7620, 07/2014
TYPE=GWDATA - Changing gateway identification

Make the settings on the STMI2-IGW Board Data tab and Save.

Board Maintenance
with OK.
CHANGE-
CGWB:MTYPE=CGW,TYPE=GWDATA,LTU=3,SLOT=91,GWID1=INTGW0
01;
effective. Use
for this.

Language
CGWB LTU d LTU-Nummer des Rahmens, in dem die HG
3500 gesteckt ist.
HG 3500 is plugged.
GWID1 d Gateway Identifikation 1. Teil
Die Gateway Identifikation ist der 1. Teil einer
beliebigen 64 Zeichen langen Zeichenkette. Die
Eingabe ist CASE-sensitiv.
GWID1 e Gateway Identifikation 1. part
A gateway identification is the 1. part of an
idividual 64 character long characterstring. The
input is CASE-sensitive.
STMIB GWID2 d Gateway Identifikation 2. Teil
Die Gateway Identifikation ist der 2. Teil einer
beliebigen 64 Zeichen langen Zeichenkette. Die
Eingabe ist CASE-sensitiv.
STMIB GWID2 e Gateway Identifikation 2. part
A gateway identification is the 2. part of an
idividual 64 character long characterstring. The
Table 5 AMO CGWB parameters in the CHANGE branch under

MTYPE=CGW, TYPE=GWDATA
A31003-H3160-S104-8-7620, 07/2014
Resetting the parameters to default values

You can reset the initialization settings with the command:
CHANGE-CGWB:MTYPE=INITCGW,TYPE=GWDATA;
TYPE LEGKDATA - Changing the gateway directory number

Make the settings on the STMI2-IGW Board Data tab and Save.

Board Maintenance
with OK.
CHANGE-
CGWB:MTYPE=CGW,TYPE=LEGKDATA,LTU=3,SLOT=91,GWNO=3,GWD
IRNO=354711;
effective. Use
for this.

Language
gesteckt ist.
HG 3500 is plugged.
GWNR d Gateway Nummer
Die Gateway Nummer dient zur Identifikaiton der
HG 3500 und ist immer erforderlich, wenn ein
Gatekeeper an der lokalen PBX betrieben wird. 
Verfügt die lokale PBX über keinen Gatekeeper
so wird auch keine Gateway Nummer benötigt
Der Default-Wert ist 0 (dezimal)

MTYPE=CGW, TYPE=LEGKDATA
A31003-H3160-S104-8-7620, 07/2014

Language
GWNO e Gateway number
A gateway number is used to identify a HG 3500
and it necessary, when a gatekeeper is operating
on the lokal PBX.
Is there no gatekeeper working on the lokal PBX
then no gateway number is needed
Default value is 0 (decimal)
GWRNR d Gateway Rufnummer
Legt eine Rufnummer fest, mit der das Gateway
an der lokalen PBX erreichbar ist. 
Die Rufnummer muß eigens mit dem AMO
WABE und Kennzahlpunkt QUER eingerichtet
werden.
GWSTNO e Gateway station number
Assigns an access code, with which a gateway
can be reached on the local PBX.
The access code must be specially configured
with AMO WABE and DAR = QUER.
REGEXTG d Gateway Registrierung an einem remote
K Gatekeeper
Damit wird gesteuert, ob sich ein Gateway an
einem remote Gatekeeper registrieren darf.
REGEXTG e Gateway registration at remote gatekeeper
K Controls, if a gateway is permitted to register at a
remote gatekeeper.

MTYPE=CGW, TYPE=LEGKDATA

Resetting the CGWB parameters for the LEGKDATA is neither helpful nor
supported. You can only set other values with the command:
CHANGE-CGWB: MTYPE=STMI2IGW,TYPE=LEGKDATA, ...... ;
A31003-H3160-S104-8-7620, 07/2014
TYPE DMCDATA - Changing the number of DMC connections

Click Search and select the board. Make the settings on the STMI Board
Data tab and Save.

Board Maintenance
with OK.
CHANGE-
CGWB:MTYPE=CGW,TYPE=DMCDATA,LTU=3,SLOT=91,DMCCONN=8;
effective. Use
for this.

Language
gesteckt ist.
HG 3500 is plugged.
DMCCONN d Anzahl der möglichen DMC Verbindungen
Legt den Maximalwert der möglichen DMC
Verbindungen für die HG 3500 fest.
DMCCONN e Number of possible DMC connections
Assigns the maximum number of possible DMC
connections for the HG 3500.

MTYPE=CGW, TYPE=DMCDATA

CHANGE-CGWB:MTYPE=INITCGW,TYPE=DMCDATA;
A31003-H3160-S104-8-7620, 07/2014
TYPE GLOBIF - Changing the default router IP address

Click Search and select the board. Make the settings on the STMI2-IGW
Board Data tab and Save.

Board Maintenance
with OK.
CHANGE-
CGWB:MTYPE=CGW,TYPE=GLOBIF,LTU=3,SLOT=91,DEFRT=192.16
8.1.254;
effective. Use
for this.

Language
gesteckt ist.
3500 is plugged.
DEFRT d IP-Adresse der Default Routers
Der Default-Wert ist 0.0.0.0
DEFRT e Default router IP-address
Default value is 0.0.0.0

MTYPE=CGW, TYPE=GLOBIF

CHANGE-CGWB:MTYPE=INITCGW,TYPE=GLOBIF;
TYPE GKDATA - Changing IP addresses for primary and secondary

gateways
This step is only necessary if there is no gatekeeper configured on the local
HiPath 4000 system and a gateway should register at a foreign PBX’s
gatekeeper. Use this command to enter the IP addresses of the relevant
gateways.
A31003-H3160-S104-8-7620, 07/2014
Point
Click Search and select the access point, change data and Save.
CHANGE-
CGWB:MTYPE=CGW,TYPE=GKDATA,LTU=3,SLOT=91,PRIGKIP=192.
168.1.90,PRIGKPN=1719,PRIGKID1=PRIMARYRASMANAGERID;
In this case, only a primary gatekeeper is assigned.
effective. Use

Language
gesteckt ist.
3500 is plugged.
PRIGKIP d IP Adresse der HG 3500 des primär
anzusprechenden Gatekeeper
Jeder Gatekeeper wird durch eine IP-Adresse
adressiert.
PRIGKIP e IP address of the HG 3500 for the primary
addressed gatekeeper
Every gatekeeper is addressed by it’s own IP
address
PRIGKPN d Portnummer der HG 3500
Die Portnummer für HG 3500 ist standardmäßig
1719.
PRIGKPN e Portnumber of HG 3500
The default portnumber for a HG 3500 is .1719.
PRIGKID1 d ID des primär anzusprechenden Gatekeeper - 1.
Teil
Der Default-Wert ist “PrimaryRASManagerID“.
Die Eingabe ist CASE-sensitiv.
PRIGKID1 e ID of the primary addressed gatekeeper - 1. part
Default value is “PrimaryRASManagerID“. The

MTYPE=CGW, TYPE=GKDATA
A31003-H3160-S104-8-7620, 07/2014

Language
PRIGKID2 d ID des primär anzusprechenden Gatekeeper - 2.
Teil
Die Eingabe ist CASE-sensitiv.
PRIGKID2 e ID of the primary addressed gatekeeper - 2. part
The input is CASE-sensitive.
SECGKIP d IP Adresse der HG 3500 des sekundär
anzusprechenden Gatekeeper
Jeder Gatekeeper wird durch eine IP-Adresse
adressiert.
SECGKIP e IP address of the HG 3500 for the secondary
addressed gatekeeper
Every gatekeeper is addressed by it’s own IP
address
MTYPE=CGW, TYPE=GKDATA

CHANGE-CGWB: MTYPE=INITCGW,TYPE=GKDATA;
Display:
AMO BCSU
When configuring a HG 3500, the distribution and number of available IP

connections (B channels) is defined with the HG 3500 FCTID in the AMO BCSU.
In contrast to NCUI4 and STMI2/4, no supplementary information, such as IP

address, B channels, etc., is output for a HG 3500 gateway.
Displaying can be performed with the HiPath 4000 Assistant/Manager,

Boards window.
DISPLAY-BCSU:TAB,1,LTU Number,Slot;
The AMO outputs typical board data for the common gateway.
DIS-BCSU:TBL,1,3,91;
ADDRESS : LTG 1 LTU 3 SOURCE GROUP 1
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------|
| | | |S|H|AL-| | | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE |
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS |
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------|
91 | Q2316-X10 STMI2 1 A 0|*| Q2316-X10 | -05 - | READY |
+--------------------------------+-+------------+------------+-----------|
| IP ADDRESS : 192.168. 1. 11 B-CHANNELS : 120 BCHLCNT : 120 |
| BLOCK NO : 1 PRERESERVED LINES ASSIGNED : NO |
A31003-H3160-S104-8-7620, 07/2014
| 1. FUNCT : STMI2-IPGW 1 LINES B-CHANNELS : 30 BCHLCNT : 30 |

+--------------------------------+-+------------+------------+-----------|
AMO CGWB
Displaying with the AMO CGWB can only be executed in expert mode.
Expert Mode > HiPath 4000 Expert Access > Open ...<IP> with AMO
(see AMO command)
DISPLAY-CGWB:CGW,<LTU Number>,<Slot>;
The AMO outputs all HG 3500 specific data.
Values must be configured for the following data to ensure correct operation:
• Ethernet interface
• Gateway data
• Gatekeeper-specific data
Delete:
AMO BCSU
Deletion with the AMO BCSU can only be executed in expert mode.
Expert Mode > HiPath 4000 Expert Access > Open ...<IP> with AMO
(see AMO command)
DELETE-BCSU:PER,,LTU Number,Slot,Part Number;
The AMO deletes the specified board from the HiPath 4000 system.
AMO CGWB
The AMO does not feature a DELETE branch. The configuration data modified
with the AMO CGWB (TYPE=LEGKDATA) for a local gateway is deleted when
deleting the AMO GKREG.
This data can be restored at any time with the AMOs CGWB and GKREG.
Resetting the parameters to default values:

• Resetting the CGWB parameters for the LEGKDATA is neither helpful nor
supported.
• You can reset the initialization settings for individual data types with the
command:
CHANGE-CGWB:MTYPE=INITCGW,TYPE=<param>;
• You can reset the initialization settings for all data types with the command:
CHANGE-CGWB:MTYPE=INITCGW,TYPE=ALL;
A31003-H3160-S104-8-7620, 07/2014
3.5.1.2 Configuring HG 3500 Circuits
You must configure the appropriate number of circuits for every common gateway
board based on its configuration (see AMO BFDAT: parameter FCTBLK). As for
all circuits, the AMO TDCSU is used for this.
Please note that this step requires a number of HG 3500 specific parameters that
are grouped together for all AMO commands in the branch EVN=HG3550IP.
The parameter DMCALLWD is used to define whether or not this circuit can be
used in a direct media connection.
Please note that you may have to configure the necessary circuit data (for
example, circuit and line parameters, trunk groups, etc.) in advance using the
relevant AMOs.
Each circuit in HG 3500 must have a separate trunk group.
3.5.1.3 Changing the HG 3500 Gateway Registration
The HiPath 4000 system does not support a direct change of the gateway
registration type from remote to internal gatekeeper, and vice versa. Furthermore,
the AMO ZANDE parameter GATEKPR must not be changed while a gateway is
configured. This may cause major disruptions during operation!
Since the AMO CGWB has no DELETE branch, the AMO BCSU must be used to
delete the internal HG 3500 configuration data and the extended board data.
• In a PBX with/without gatekeeper, the HG 3500 gateway(s) must always be

deleted first and then reconfigured. Please note that in such a case all
gateways will be registered either internally (PBX with gatekeeper) or
remotely (PBX without gatekeeper).
• Changing registration of gateway(s) from “internal“ to “remote“:

Delete gateway(s) with AMO GKREG and AMO BCSU, change the
GATEKPR parameter to NO and reconfigure the gateway with AMO
BFDAT, AMO BCSU and AMO CGWB.
• Change registration of gateway(s) from “remote“ to “internal“:

Delete the gateway(s) with AMO GKREG and AMO BCSU, change the
GATEKPR parameter to YES and reconfigure the gateway with AMO
BFDAT, AMO BCSU, AMO CGWB and AMO GKREG.
• In a PBX with gatekeeper, the registration of some special, local gateway(s)

can be changed from internal to remote:
Delete the gateway data with AMO GKREG and then reconfigure the gateway
with AMO CGWB (REGEXTGK=YES) !
A31003-H3160-S104-8-7620, 07/2014
• In a PBX with gatekeeper, an additional, local gateway can be configured for

remote registration:
Configure the gateway with AMO BFDAT, AMO BCSU and AMO CGWB
(REGEXTGK=YES)!
A31003-H3160-S104-8-7620, 07/2014
Configuring the HG 3500 Directory Number
3.6 Configuring the HG 3500 Directory Number

Every HG 3500 requires a directory number with which it can be contacted in the
gatekeeper’s HiPath 4000 system. The AMO CGWB presents the directory
number to the HG 3500 (command: ADD-
CGWB:MTYPE=CGW,LTU=<number>,SLOT=<number>,TYPE=LEGKDATA,GW
DIRNO=<GW directory number>;).
A HG 3500 that has to register at a foreign HiPath 4000 system with gatekeeper
does not have to have an entry its own HiPath 4000 system’s digit analysis
scheme. However, the directory number must be configured under the GATEWAY
digit analysis result or, if the number contains more than six digits, in the LCR in
the system with gatekeeper.
The DPLN entry for a remote HG 3500 at the HiPath 4000 system with
gatekeeper requires the associated gateway number as supplementary
information. This is administered, that is, the relevant DPLN entry is entered or
deleted with the AMO GKREG in the course of configuration or deletion. This
ensures that operation can only start if the gateway is correctly configured in the
LEGK administration.
The HG 3500s own directory number must come from the station’s numbering
plan.
The gateway directory number must be configured under the TIE digit analysis
result (TSC connection) in a HG 3500 that has to register at the local HiPath 4000.
A gateway number is not essential as supplementary information in this case.
The DPLN entry for a HG 3500 (GATEWAY digit analysis result) can only be
deleted after the gateway number has been removed. Use the AMO GKREG to
delete the gateway from the LEGK administration.
Generation
AMO WABE
Configure the directory number of a remote HG 3500 in the local system, that is,
the gateway must register at the local LEGK. In this case, the gateway must be
configured with the GATEWAY digit analysis result.
Configuration can be performed with HiPath 4000 Assistant/Manager in the

Extension window (TYPE=GATEWAY).
ADD-WABE:CD=35101,DAR=GATEWAY;
For the predefined traffic situations, the remote gateway’s directory
number (35101) is configured as the gateway digit analysis result in the
digit analysis scheme.
Configure the directory number of a remote HG 3500 in the system with

gatekeeper, that is, the gateway can register at the local gatekeeper. In this case,
the gateway must be configured with the TIE digit analysis result.
A31003-H3160-S104-8-7620, 07/2014
Configuring the HG 3500 Directory Number

Extension window (TYPE=TIE).
ADD-WABE:CD=452001,DAR=TIE;
For the predefined traffic situations, the local gateway’s directory number
(452001) is configured as the tie line digit analysis result in the digit
analysis scheme.
Display:

Extension window.
DISPLAY-WABE:GEN,Directory Number;
The AMO outputs data on the specified directory number.
Delete:

Extension window.
DELETE-WABE:CD,Station Number,,Digit Analysis Result;

The AMO deletes the required directory number for the specified digit
analysis result.
A31003-H3160-S104-8-7620, 07/2014
Configuring IP Trunking in the LCR
3.7 Configuring IP Trunking in the LCR

When resolving addresses for TDM connections, an LCR route is administered
as destination address information and is subsequently used to determine the
LODEN of a remote circuit for CO or TIE connections.
To satisfy the requirements of IP address resolution, new parameters for

destination gateways (GW1 to GW5) are administered in the LCR data with the
AMO LDAT. Information on destination gateways 1...5 consists of:
a) the gateway number
b) the sector path number
The gateway number can be used to determine the IP address of the destination
gateway and therefore to reach every required HiPath 4000 system in the
customer’s IP network.
Enter all sectors to be crossed between the source and destination gateway
under the sector path number. It does not contain the sector numbers of the
source and destination gateway.
There are no multiple paths for this path type. In other words, there is only one
defined path. To avoid having to configure an unnecessary number of sector
paths, you can also specify a sector path that was defined for DMC here. If this is
a multiple path, a search is performed here for the correct sector path segment.
For the sake of clarity, however, separate sector paths should be defined for IP
trunking and DMC.
The IP address resolution administration concept is embedded in the existing

LCR device search and can be performed with the same AMOs (namely the
AMOs RICHT, LDAT, and LDPLN).
Node 1 
 S101 Node 2 
LAN
HG 3500 LAN S301
WAN S302 
S13 S201
HG 3500
S23
Figure 3 Example for sector path description
An outgoing seizure from gateway S13 to gateway S23 uses the following sector
path:
S13 --> S23: S101,S301,S302,S201
Generation
AMO RICHT
A31003-H3160-S104-8-7620, 07/2014
Use the branch MODE=LRTENEW to configure the LCR route for IP trunking.
Alternatively, the trunk group number can be left out when configuring IP address
resolution for a remote gateway (HiPath 4000 system without gatekeeper)
because B channels do not have to be seized at the gatekeeper’s PBX in this
case.

LCR Route window.
ADD-RICHT:MODE=LRTENEW,LRTE=35,LSVC=ALL,NAME=“STMI2
3-91“,DNNO=1-69-
300,REROUT=NO,ROUTATT=NO,EMCYRTT=NO,PDNNO=10-69-
300,CHARCON=NEUTRAL,CONFTONE=NO,RERINGRP=NO;
Route 35 is configured on PEN 3-91 for all services for HG 3500; no trunk
group number was entered.
AMO LDAT
Use this AMO to configure the necessary LCR route elements for IP trunking for
an LCR route.
Every route element can contain up to five destination gateways from remote
HiPath 4000 systems. The parameters GW1 through GW5 define the connection
setup sequence, that is, first the path described in GW1 and so on until finally the
path in GW5.
If five destination gateways is not sufficient, then a new route element must be
configured and in addition, the value LRTGCONT must be specified in the
parameter LATTR. This creates five additional destination gateways for the same
route element. All data associated with the route element already created is
automatically adopted independently of the current AMO input.
As in the past, multiple route elements can also be configured with different LCR
parameters for an LCR route. In this case, the parameter LATTR must not contain
the value LRTGCONT.
The trunk group number can be left out. If a trunk group number is specified, all
trunk-group-specific data is also adopted.

LCR Route Element window.
A31003-H3160-S104-8-7620, 07/2014
ADD-
LDAT:LROUTE=35,LSVC=ALL,LVAL=1,ODR=2,LAUTH=1,CARRIER=
1,ZONE=TIE01,LATTR=WCHREG,VCCYC=4,GW1=1-1;
A route element is created for route 35 with path data for destination
gateway 1.
ADD-
LDAT:LROUTE=35,LVAL=1,ODR=2,LAUTH=1,LATTR=LCRCONT,GW1
=6-16;
If the path data for all five destination gateways is entered in a route
element for route 35, this follow-up command can be used to create
another route element with the path data, for example, for the sixth
destination gateway.
AMO LDPLN
Use this AMO to configure the LCR digit pattern for each destination gateway in
the HiPath 4000 systems in a customer network.
Up to 2,048 dial plans can be configured. But first, the required dial plan numbers
must be administered with the AMO LDPLN. Dial plan number 0 is an exception.
This configures fixes and cannot be administered in the branch
LCRCOS=LCRADM. Random digit patterns can be configured here immediately.
If you want to save the LCR digit pattern under a dial plan number other than 0,
then this must be configured before the first entry. The branch
LCRCONF=LCRVADM is used for this. In the following AMOs, the user only uses
the dial plan number (0-2047).
A dial plan number greater than the permanently set plan 0 is usually only needed
if a gatekeeper is configured at the local system.

LCR Digit Pattern window.
ADD-LDPLN:LCRCONF=LCRADM, DIPLNUM=2,LWMPOOL=1;
Dial plan number 2 is configured on the first unused dial plan in LCR digit
pattern pool 1.
Use the following step to configure the required digit pattern.

ADD-
LDPLN:LCRCONF=LCRPATT,DIPLNUM=2,LDP=“00891242390“,LAU
TH=1,PINP=N;
The digit pattern 00891242390 is created under dial plan number 2.
A digit pattern that leads to a gateway is an exception.
A31003-H3160-S104-8-7620, 07/2014
If a gateway directory number cannot be resolved with the dial plan (DPLN), it
must be administered in the LCR dial plan DIPLNUM=0. The following command
is required for this (see also Section 3.6, “Configuring the HG 3500 Directory
Number”, on page 495).

ADD-
LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=“008973114711“,GW
NO=7,LAUTH=3;
The gateway directory number 008973114711 is assigned to destination
gateway 7.
Display:
AMO RICHT
Displaying can be performed with HiPath 4000 Assistant/Manager in the

LCR Route window.
DISPLAY-RICHT:MODE=LRTE,LRTE=35;
The AMO outputs the LCR routing data for LRTE 35.
AMO LDAT

LCR Route Element window.
DISPLAY-LDAT:KIND=LCR,LROUTE=35;
The AMO outputs the routing data configured for all configured route
elements for LCR route 35.
AMO LDPLN
Display the internal administration configuration for dial plan number 2.

DISPLAY-LDPLN:LCRCONF=LCRADM,DIPLNUM=2;
The AMO outputs the administrative data LWMPOOL, DIALPLN and INFO
for dial plan number 2.
Displaying the digit pattern configured for gateway 7.
A31003-H3160-S104-8-7620, 07/2014

DISPLAY-LDPLN:LCRCONF=LDP,GWNO=7;
The AMO outputs the digit pattern data configured for gateway 7.
Delete:
AMO RICHT
Deletion can be performed with HiPath 4000 Assistant/Manager in the LCR

Route window.
DELETE-RICHT:MODE=LRTE,LRTE=35;
The AMO deletes LCR route 35.
AMO LDAT

Route Element window.
DELETE-LDAT:KIND=LROUTE,LROUTE=35;
The AMO deletes all route elements and data for LCR route 35.
OR
DELETE-LDAT:KIND=LRTEL,LROUTE=35,LRTEL=1,GWIDX=2;
The AMO deletes only the second gateway entry for LCR route 35 in route
element 1.
The last gateway in an LCR route element cannot be deleted with GWIDX.
In this case, the entire route element (LRTEL) must be deleted.
AMO LDPLN
Delete the internal administration configuration for dial plan number 2.

A dial plan number can only be deleted after all digit patterns have been deleted.

Digit Pattern window.
DELETE-LDPLN:LCRCONF=LCRADM,DIPLNUM=2;
The AMO deletes dial plan number 2. Data can no longer be accessed on
these dial plans. Dial plan number 2 should be reconfigured when next
required.
Delete the digit pattern configured for a dial plan number.
A31003-H3160-S104-8-7620, 07/2014
Deletion can be performed with HiPath 4000 Assistant/Manager in the

Extension window.
DELETE-
LDPLN:LCRCONF=LCRPATT,DIPLNUM=6,LDP=“0307469412“;
The AMO deletes the digit pattern 0307469412 configured for gateway 6.
A31003-H3160-S104-8-7620, 07/2014
Configuring Circuits and Terminals
3.8 Configuring Circuits and Terminals
3.8.1 Configuring Circuits

This feature does not change the underlying configuration of the analog (AMO
TACSU) and digital line trunks (AMO TDCSU) or special circuits (TSCSU).
Parameter CLASSMRK is set to „HG3550: Bandwidth control for integrated HG

3550 IP gateway“.
3.8.2 Configuring Terminals

This feature does not change the underlying configuration of the terminal data
(AMO SDAT) and attendant console (AMO ACSU).
Parameter CLASSMRK is set to „HG3550: Bandwidth check for HG 3550 IP

trunk“.
The parameter IPCODEC was also added to the AMO SBCSU. This can be used
to set the codec type for IP terminals. The value G711PREF is designed as the
default value for STMI2/4-HFA terminals.
A31003-H3160-S104-8-7620, 07/2014
Changing the System Bandwidths
3.9 Changing the System Bandwidths

You can use the AMO SIPCO to change the default bandwidths set for IP
connections under TYPE=BANDW.
A default bandwidth (in kilobits) established on the basis of previous experience

was permanently set in the existing table for every codec type and sample size.
These values can be changed with the AMO SIPCO.
Add:
Example: Change the setting for entry no. 3 to 90 kilobits
Data
Click Search, deactivate the Enable Autonegotiation check box under
Type of Service on the Bandwidth Data tab, enter Speed and Mode, and
Save.
CHANGE-SIPCO:TYPE=BANDW,TBLIDX=3,BWRES=90;
This command changes the bandwidth for index 3 to 90 kilobits.
Example: Restore the default values for the entire table
CHANGE-SIPCO:TYPE=BANDW,TBLIDX=0,STANDBW=Y;
This command resets the entire table to the defined system bandwidths.

Language
SIPCO TBLIDX d Index eines Eintrages in der Bandbreitentabelle
TBLIDX e Index of an entry in the bandwidth encoding time
table
BWRES d neuer Wert für reservierte Bandbreite in kBit
BWRES e new value for reserved bandwidth in kBit
STANDBW d Rücksetzen auf Standardwerte
Wird BWRES=0 angegeben so wird die
gesamte Tabelle auf die Standardwerte
zurückgesetzt sonsten nur der angegebene
Index.
Table 10 AMO SIPCO parameters in the CHANGE branch under

TYPE=BANDW
A31003-H3160-S104-8-7620, 07/2014

Language
STANDBW e reset to default values
Is BWRES=0 entered then the whole table is
reset to the default values, otherwise only the
entered tableindex..
Table 10 AMO SIPCO parameters in the CHANGE branch under
TYPE=BANDW
Delete:
Example: Delete index 5 in the system bandwidth table
DELETE-SIPCO:TYPE=BANDW,TBLIDX=5;
This command deletes the bandwidth for table index 5.

Language
table
Table 11 AMO SIPCO parameters in the DISPLAY branch under

TYPE=BANDW
Display:
Example: Output the set system bandwidth table
This command outputs all configured entries from the system bandwidth
table.

Language
table
Table 12 AMO SIPCO parameters in the DISPLAY branch under

TYPE=BANDW
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
hfa_01_overview.fm
Overview
HiPath Feature Access (HFA)
1 Overview
The HG 3500 gateway provides IP phones and analog devices access to the full
range of HiPath 4000 features via CorNet IP.
Figure 1 Typical HG 3500 Configuration
The HG 3500 provides the following features and benefits:
• Provides the full HiPath 4000 feature set to the following IP phones:
– optiPoint 4x0 CorNet IP
– OpenStage family,
– AP 1120 analog adapter (For more details please refer to the E-Doku
pages in the intranet (http://apps.g-dms.com:8081/edoku/jsp/
searchresult_v2.jsp?edokutype=&search_mode=product&product=AP%
201120&product_version_main=&product_version_sub=&search_term_t
ype=all&term=&sort_result=title&docclass=&language=&checkdate=&la
ng=en))
• The HG 3500 line gateway supports direct media connections between IP

clients resulting in highest quality voice and minimal delays.
• High voice quality. On account of longer voice signal delays caused by the
system in the IP network, voice quality will be impaired by echo unless this is
removed prior to transmission. The HG 3500 therefore feature an integrated
echo canceller.
• The HG 3500 provides a 10BT/100BT IP network interface and supports up

to 240 IP phones off a single gateway.
• Lower bandwidth requirements.
• The HG 3500 supports all phone adapters that do not require their own b
channel (not supported are: phone adapter, a/b adapter, S0 adapter, V.24
adapter).
• The HG 3500 supports standby gateways that protect multiple gateways

against failure.
• The HG 3500 supports mobility including support for E911.
• Supports central administration via HiPath 4000 Management identical to

traditional subscribers.
• Support for IP phones provides user mobility and greatly simplified MAC.
A31003-H3160-S104-8-7620, 07/2014
hfa_01_overview.fm
Overview
• Takes advantage of existing IP infrastructure.
• Supports up to 12,000 IP subscribers off a single HiPath 4000 including IP

users on IP Access Points.
• Support for Quality of Service in the IP network through prioritization. The HG

3500 supports prioritization in the IP network on the basis of the following
standards:
• IEEE 802.1 p/q (VLAN Tagging) on Layer 2
• IETF RFC 2474 (DiffServ) on the IP Layer
• Support of network management on the basis of SNMP. HG 3500 supports

network management on the basis of the SNMP protocol. Statistical data from
the applicable standard MIBs and additional data from proprietary MIBs can
be queried.
A31003-H3160-S104-8-7620, 07/2014
hfa_02_configuration.fm
Application Example
Feature Description
2 Application Example

HiPath Feature Access (HFA) allows the smooth migration of the communication
platform from a wire-connected to IP-based infrastructure. Consequently, it is
sufficient for the customer just to install and operate an efficient Local Area
Network (LAN) that supports Quality of Service (QoS). Data and voice
communication share the available network bandwidth where the throughput rate
is important for data traffic and the real-time capability is important for telephony.
This means that, before the installation of an HFA system, the appraisal and
actualization of the IP infrastructure regarding bandwidth and QoS-supporting
LAN components (Router, Switch, Gateway) is crucial for the subsequent quality
of the voice connections.
OpenStage optiPoint 410,

TDM 420
Up0
IP
IP
LAN
HG 3500
HiPath 4000
Figure 2 HFA infrastructure
To guarantee good voice quality even when the network is very busy the LAN
segment that is used must consist of QoS-supporting LAN components. The use
of a 100Mbit Ethernet is also recommended.
Supporting Quality of Service in the IP network through prioritization
• IEEE 802.1 p/q (VLAN tagging) on Layer 2
• IETF RFC 2474 (DiffServ) on Layer 3.
A31003-H3160-S104-8-7620, 07/2014
Application Example
Feature Description
There are no significant restrictions for the user, only Autoset-Relocate and
Teleworking are not supported. Otherwise the IP terminals provide the same
functionality as UP0e-based terminals. However, no S0 or a/b adapters are
supported.
G.711, G.723 and G.729 are supported with HG 3500. With a Direct Media
Connection (DMC), the optiPoint 410 / 420 terminals also control G.722 with CD
quality.
2.1.1 Technical background

In UP0e-based user connections the signaling connection (D channel) is
separated from the voice connection (B channel) by subdividing the physical
medium into time slots and assigning the two connections different time slots. In
HFA, the two-wire line is replaced by an IP-based LAN as the physical medium of
the digital user connection. The signaling connection between the terminal and
HFA (Common) Gateway uses a secure TCP connection and the voice data are
transferred via an H.323 connection using the RTP/RTCP protocol. Both
connections can now be routed differently in a single LAN. This means it is
possible for there to be signaling although the voice connection is temporarily
interrupted.
Ethernet Interface
Ethernet Interface with Signaling connection with OP400 IP
Gateway IP address, corresponds to the address, e.g.
e.g. 1.30.11.40 UP0e D channel 1.30.11.91
CorNet TS over IP
H323
RTP/RTCP
Voice connection
corresponds to the B
channel of a UP0
Figure 3 Technical relationship between UP0e and HFA user connection
In order to configure an HFA user, primarily it is necessary to determine the

following points beforehand:
• IP address, subnetwork mask, subnetwork Gateway IP address of the

Common Gateway
• IP address, subnetwork mask, subnetwork Gateway IP address of the HFA

terminal
A31003-H3160-S104-8-7620, 07/2014
Application Example
Feature Description
2.1.2 HFA user registration

Users are configured at a specific PEN (AMO SBCSU). While, however, a digital
(or analog) terminal can go directly into operation after connecting to its module,
in the case of an IP telephone settings must be first made at the terminal.
Firstly an HFA user needs a separate IP address, a subnetwork mask and -

optionally - the specification of a default (customer network) router. In the case of
a Soft Client, it has, of course, the advantage that it uses the network card of the
PC and, consequently, no settings are required.
However, in the case of an HFA fixed device, the IP settings must be made. This
is either done “automatically“ via DHCP (default setting of the HFA fixed
terminals) or manually.
A HFA user with IP settings now attempts to register with the appropriate
gatekeeper. Its gatekeeper is the HG 3500 at whose position it is configured. In
order to find its “home“ HG 3500, its IP address must be set up at the terminal.
This alone, however, is not sufficient. The HG 3500 still has to check whether the
user who is sending it a “Registration Request“ is actually authorized to register
with it. The terminal must also send it the user number for checking the user
identity. The HG 3500 then asks the HiPath 4000 whether this user number is set
up at its position. If it is, the HFA user is registered. If not, the HFA user is denied.
Thus, the user number must be set up beforehand on the terminal.
To prevent a user simply registering himself with the subscriber number of

another colleague, it is even possible to set up a so-called IP password
(IPPASSW) in the AMO SBCSU. This can only be changed via the administrator,
but not by the user at the terminal. If an IP password is set up in the AMO SBCSU,
it must also be configured at the terminal. Otherwise, the subscriber is not
registered.
Conclusion:
The IP address of the HG 3500, user number from the AMO SBCSU and,
optionally, the IP password from the AMO SBCSU must be configured at the
terminal. Otherwise, the HFA terminal will not be registered and, thus, will remain
out of operation. The configuration of these data can take place at the terminal
itself, via the WBM or via the DLS.
In case of a SoftClient, the respective configuration is made after the program is

invoked.
Note:
In some customer networks it may also be necessary to preset the L2

prioritization and the VLAN ID at the HFA terminal. Here, however, it is also
possible to automate this via DHCP.
A31003-H3160-S104-8-7620, 07/2014
Application Example
User interface
Following successful registration, the HG 3500 transfers data concerning the HFA
user to the AMO SBCSU such as, e.g. device type, IP address, etc. (AB-SBCSU
/ branch TYPE=OPTIDAT). These data can also be viewed in the UW7 via the
Configuration Menu in the user overview!
In the following figure the registration for user 4711 has already been carried out.
The other telephone has all IP settings, but is not yet registered.
User 4711 HFA phone

deregistered User 4711
Step 1
Step 2
Legend
HFA phone configured
HFA user registered
Figure 4 A user registers at another HFA phone
If an HFA user is already registered, he can change to another HFA terminal by

registering there and declaring the IP address of his “home“ HG 3500, his user
number and his optional IP password. The original terminal is automatically
deregistered by the new registration. This is only not possible if there is an
existing telephone connection to the original terminal. It is possible for HFA users
to make the transfer to another terminal via a digit analysis result in the WABE.
This means that the user at the terminal no longer needs to call up the hidden
configuration menu for a transfer. How to set up “Mobile HFA” please refer to IP
Solutions, “Mobile HFA Logon“.
2.2 User interface

The user interface for the administration of IP HFA terminals is specific to each
terminal. More details are given in the administration handbooks for the relevant
terminals and are not, therefore, included in this document.
To setup a HFA phone you can either use:
• direct administration at the phone or via WBM of the phone.

Please refer to the apropriate documentation of your HFA phone (http://
apps.g-dms.com:8081/techdoc/search_en.htm).
• OpenScape Deployment Service (DLS):
A31003-H3160-S104-8-7620, 07/2014
Application Example
Restrictions
Please refer to the documentation of the DLS (http://apps.g-dms.com:8081/

techdoc/en/P31003S2330M1000176A9/index.htm).
The following parameters are mandatory for the phone to go into operation:
• fully qualified phone number (E.164)
• gateway (HG3500) address and port
• subscriber password
If a user has successfully registered, the same user interface is available as for
the standard digital terminals.
WBM
Web Based Management
2.3 Restrictions
The following functional restrictions apply:
• Autoset-Relocate is not usable for the HFA user
• Teleworking TW2.6 is not allowed for the HFA user
• No S0 or a/b adapter are supported
2.4 Generation
IMPORTANT: If T.38 is supposed to be used with AP 1120, G.711 must be

configured as voice codec only, i.e. always in case a modem or fax is connected
to an AP 1120 the only allowed codec in the AP 1120 has to set to G.711 (no
option for compression).
Before the initial configuration of an HFA user, the memory configuration must be
checked with the AMO-DIMSU:
TEST-DIMSU:LIST=Y;
Now to configure 4 modules, for example, the following configuration must be
carried out:
The G.711 code type setting (a law or µ law) of the IP voice data is carried out via
the central system data (usually already correctly set):
CHANGE-ZAND:TYP=CONFC,CODE=<ALAW/ULAW>;
A31003-H3160-S104-8-7620, 07/2014
Application Example
Generation
Now the configuration of the HG 3500 module can be started.
2.4.1 Configuration of the HG 3500 board

The configuration of the function blocks is carried out with AMO-BFDAT. In the
following example an STMI4 (Q2324-X510) with 120 possible b-channels will be
configured with HFA.
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=6,FUNCTION=HG3530,LINECNT=60,BC
HLCNT=60; /*60 HG 3530 b-channels are configured
With the following command the configuration of the board is completed:

The configuration of the module is carried out with the AMO BCSU.
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=3,SLOT=14,PARTNO=“Q2324-
X510“,FCTID=1,LWVAR=“0“,FCTBLK=6,BCHL3530=60,ALARMNO=0;
For the configuration of the IP addresses, subnetwork masks, etc., the loadware
is carried out via the AMO-CGWB.
ADD-CGWB:LTU=3,SLOT=14,SMODE=NORMAL,IPADR=172.28.145.240,
NETMASK=255.255.255.0;
Now the module data and the circuit data have still to be loaded onto the module.
This is done either by plugging in the STMI module after the generation with the
AMO CGWB or using the command:
RESTART-BSSU:ADDRTYPE=PEN,LTG=1,LTU=3,SLOT=14,WTIME=<Wait
time between switching off and switching on in seconds>;
2.4.2 Configuration oth the HFA users

The HFA users (IP phones) can then be configured.
ADD-SBCSU:STNO=<stno>,OPT=OPTI,CONN=IP2,PEN=1-3-14-
0,DVCFIG=OPTIIP,
COS1=33,COS2=30,LCOSV1=5,LCOSV2=1,LCOSD1=5,LCOSD2=1,DPLN=0,IT
R=0, [IPPASSW=<Password>];
If a soft client has the special feature that it has TAPI 1st party as a feature, the
following AMO SBCSU configuration is required:
ADD-SBCSU:STNO=<stno>,OPT=OPTI,CONN=IP2,PEN=1-3-14-
0,DVCFIG=OPTIIP&API,
COS1=33,COS2=30,LCOSV1=5,LCOSV2=1,LCOSD1=5,LCOSD2=1,DPLN=0,IT
R=0, APICLASS=TSX,[IPPASSW=<Password>];
A31003-H3160-S104-8-7620, 07/2014
Application Example
Generation via HiPath 4000 Assistant
Each HFA user can be issued with their own password for the registration which
is determined by the Administrator and, similar to the PIN, cannot be
administrated by the user himself. If no password is specified, the user call
number is sufficient for the registration.
2.5 Generation via HiPath 4000 Assistant
2.5.1 Setting up HG 3500 via the HiPath 4000

Assistant
HG 3500 can be set up and administrated via the Configuration Management of
the HiPath 4000 Assistant.
First of all you have to set the function blocks (corresponding AMO: AMO
BFDAT).
Start Configuration Management - System Data - Board - CGW Function

Block.
Click the Search button to see which function blocks have already been
configured. In the following screen 5 function blocks have been configured. You
can display them by clicking through the object list.
Figure 5 Configuration Management - System Data - Board - CGW Function

Block - View Object
You also have the possibility to view them all in one table. Just select the radio
button Object List.
A31003-H3160-S104-8-7620, 07/2014
Application Example

Block - View Object List
To configure a new function block click New. Enter a free Function block
number. Select the maximum number of b-channels of the common gateway
board. Select the desired function(s) for this function block. Click Save. Now you
have to enter the needed Number of lines, Number of predefined blocks and
/ or Number of b-channels for the selected functions. Click Save again. If you
are done with the configuration of this function block select Finish configuration
of function block and click Save.

Block - Configure new Function block
Now you have to assign a common gateway board to the function block
(corresponds to AMO BCSU). Start Configuration Management - System Data
- Board - Board. Click Search to search for all boards configured in the system.
To configure a new common gateway board select the desired board (Part
number) and click New. Enter the following data:
• LTU
• SLOT
• Part number
• Function ID (set always to 1)
• Board Name
• CGW Function block
A31003-H3160-S104-8-7620, 07/2014
Application Example
Figure 8 Configuration Management - System Data - Board - Board
Select the STMI2-IGW Board Data tab (corresponds to AMO BCSU and AMO
CGWB). Here you have to enter
• Ethernet interface
– IP address of customer LAN
– Subnet mask
– Standard gateway IP address
• Data for large enterprise gatekeeper
• CO protocol (not used in this example)
• Primary and secondary gatekeeper
• Gateway data
• H.235 security data
• Service interface
A31003-H3160-S104-8-7620, 07/2014
Application Example
Figure 9 Configuration Management - System Data - Board - Board - STMI2-

IGW Board Data tab
The next screen shows the STMI Board Data tab. Here you can configure for
exampe the Idle Pattern, IP Address and Number of DMC connections
(corresponds to AMO CGWB).
Figure 10 Configuration Management - System Data - Board - Board - STMI

Board Data tab
Save the completed settings using the Save button.
Use the Search button to go to the board you have already configured.
In the STMI Feature Access tab (corresponds to AMO CGWB) you can configure
in which mode the common gateway should work (Normal, Standby Ready or
Standby Defect), Ethernet Interface data and Audio Stream Control Data.
IMPORTANT: It is important to ensure that the number of UDP ports is at least

twice as large as the number of b-channels of the common gateway module.
A31003-H3160-S104-8-7620, 07/2014
Application Example
Figure 11 Configuration Management - System Data - Board - Board - STMI

Feature Access tab
2.5.2 Configure a HFA User via the HiPath 4000

Assistant
HFA users are configured like Up0/E users.
Start Configuration Management - Station - Station.
The Station Number, PEN, Device Combination, Connection Type, etc. can
be entered in the header of the input window.
The Basic 1 tab contains the default settings and other user data from the AMO
SBCSU.
Not shown in the next figure is the Basic 2 tab where the IPPASSW from the AMO
SBCSU is entered. The IP address of a set-up user can also seen there.
Figure 12 Configuration Management - Station - Station - Basic 1 tab
A31003-H3160-S104-8-7620, 07/2014
Application Example
Deletion
2.6 Deletion
The deletion of HFA components is not symmetrical to the generation: The AMO
CGWB has no deletion branch because one-off set-up module data are always
valid until deletion of the module with the AMO BCSU.
Example: The HFA components generated in the previous section are to be

deleted.
First, the HFA users are deleted:

DELETE-SBCSU:STNO=<number>,SVC=ALL;
The common gateway board can then be immediately deleted. This also
automatically deletes the board data, with the result that an AMO CGWB
command is not required.
DELETE-BCSU:MTYPE=IPGW,LTG=<ltgno>,LTU=<ltuno>,SLOT=<slotno>;
Now you can reconfigure the board with other functions.
2.7 Tuning the voice quality

Depending on the available infrastructure, AMO CGWB (DSP branch)offers
different configuration parameters:
• Noise suppression by Voice Activity Detection
• Problem fixing with packet delay and packet sequencing
• Echo suppression
• Sample length
This feature is controlled using the AMO CGWB. When used during operation,
the board data does not need to be explicitly reloaded in this case. The data
immediately comes into effect on the board.
HG 35XX supports various jitter buffer modes. For HG 3500, two different settings
are available:
1. Static jitter buffer with drift correction. The length of the jitter buffer always
remains constant (it is set to a fixed value in the same way as with "legacy
mode", however, the runtime of the incoming signal is not modified).
CHA-
CGWB:MTYPE=CGW,LTU=<ltuno>,SLOT=<slotno>,TYPE=JB,JBMODE=1;
WBM > Explorers > Payload > HW Modules > Edit DSP Jitter Buffer
Settings > Jitter Buffer Type: Static
A31003-H3160-S104-8-7620, 07/2014
Application Example
Tuning the voice quality
2. The adaptive jitter buffer (default settings). This mode can both correct the
drift as well as adapt its depth dynamically. The value set in the JITBUFD
parameter is not evaluated in this method. The adaptive jitter buffer is
activated via
CHA-
CGWB:MTYPE=CGW,LTU=<ltuno>,SLOT=<slotno>,TYPE=JB,JBMODE=2;
WBM > Explorers > Payload > HW Modules > Edit DSP Jitter Buffer
Settings > Jitter Buffer Type: Adaptive
The jitter buffer can still be optimized with the values for
• Average delay for voice (ms) - AVGDLYV
• Maximum delay for voice (ms) - MAXDLYV
• Minimum delay for voice (ms) - MINDLYV
• Packet loss/delay preference - PACKLOSS
• Average delay for data (ms) - AVGDLYD
• Minimum delay for data (ms) - MINDLYD
In HG 3500, it is recommended to use the adaptive jitter buffer. But, if there are
older analog fax machines a static jitter buffer could be the better choice.
Other important parameters:
• Voice Activity Detection: WBM > Explorers > Voice Gateway >
Codec-Parameters
• Echo Canceller: WBM > Explorers > Payload > HW Modules > Edit
DSP Settings
Additional parameters in AMO CGWB, TYPE=ASC:
Parameter Description
VAD Recognition of silence using Voice Activity Detection (AMO
CGWB:TYPE=ASC, VAD=<yes,no>)
RTP Sample length of the RTP packet depending on the codecs.
Average delay for voice (ms) - AVGDLYV

This defines the standard value (initial value) for the jitter buffer.
Maximum delay for voice (ms) - MAXDLYV

This defines the maximum length of the jitter buffer.
Minimum delay for voice (ms) - MINDLYV

This defines the minimum length of the jitter buffer.
A31003-H3160-S104-8-7620, 07/2014
Application Example
Activation of the voice compression
Average delay for data (ms) - AVGDLYD
This defines the standard value (initial value) for the jitter buffer for the data
service.
Minimum delay for data (ms) - MINDLYD

This defines the maximum length of the jitter buffer for the data service.
Packet loss/delay preference - PACKLOSS

The jitter buffer can be optimized by the PACKLOSS parameter. The default value
4 should always be preset initially. If the value is set to 0, 1, 2 or 3, the algorithm
attempts to prevent packet loss and increases the jitter buffer if problems occur.
Conversely, if PACKLOSS= 5, 6, 7 or 8, the algorithm increasingly attempts to
always work with a jitter buffer that is as small as possible and accepts a certain
degree of packet loss.
2.8 Activation of the voice compression

In HG 3500, voice compression is activated in the AMO CGWB (ASC branch).
The parameter CODECLST is relevant for this setting. The codec sequence is
important in this regard. In the example below, HG 3500 uses G.729 as first
choice, G.711A as second choice, and G.723 as third choice. The codec that is
actually used depends on the settings of the remote system (user).
CHANGE-
CGWB:MTYPE=CGW,LTU=<ltunr>,SLOT=<slotnr>,TYPE=ASC,PRIO=PRIO1,
CODEC=G729;
CHANGE-
CODEC=G711A;
CHANGE-
{354}CODEC=G723;
2.9 Relevant AMOs

Language
BSSU ADRART=LAGE d Adressierung ueber physikalische Lage
ADDRTYPE=PEN e Physical board/module address
BKAN3530 d Anzahl der B-Kanäle für die HG3530
Funktion
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs

Language
BCHL3530 e Amount of b-channels for HG3530
function
FCTID d Function Id (muss immer 1 sein)
FCTID e Function id (mustbe set to 1)
FCTBLK d Funktionsblock-Index (einen beliebigen
freien Funktionsblock zwischen 1-20
wählen)
FCTBLK e Function block index (choose a free
function block between 1-20)
LWVAR d Index auf Loadware Block der T1
Baugruppe
LWVAR e Index to loadware block for the t1 board
SACHNR d Baugruppensachnummer (2. und 3.
Block)
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
PARTNO e Part number (2nd and 3rd bloc)
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
SACHNR1 d Sachnummer der zu ersetzenden
Baugruppe (2. und 3. Block)
PARTNO1 e Part number of module that has to be
replaced (2nd and 3rd bloc)
SACHNR2 d Sachnummer der neuen Baugruppe (2.
und 3. Block)
PARTNO2 e Part number of new module (2nd and
3rd bloc)
TYP=IPGW d IP Gateway (Common Gateway
Baugruppe)
BFDAT ANZBKAN d Anzahl der funktionsbezogenen B-
Kanäle.
BCHLCNT e Defines the number of b-channels
related to the selected function.
LINECNT e Defines the number of lines related to
the selected function.
BGBKAN d Block fuer Baugruppe mit 60 und/oder
120 B-Kanaelen
BRDBCHL e Dedicates the block for boards with 60
and/or 120 b-channels
CONFIG=WEITER d Weitere Block-Konfiguration
ermöglichen
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs

Language
CONFIG=CONT e ontinue block configuration
FCTBLK d Dieser Index beschreibt den
Funktionsblock welcher auf dem
Common Gateway konfiguriert werden
soll. Anhand des Funktionsblocks wird
die Konfiguration der benötigten
pyhsikalischen Lines (Sätze der
FCTBLK 3 This index describes the function block
which should be configured on the
common gateway board. With that index
the amount of needed physical lines
(board circuits) is calculated.
Konfigurationsprofile des Common
Gateways fest. Dabei muss die
eventuell benötigte HG 3570 Funktion
als erste angeführt werden. Falls ein
bestimmter Line-Bereich für die
Funktionen HG 3530 oder HG 3550
entsprechende Funktion am Ende
stehen und mit dem Wert HG35xxR
abgeschlossen sein. Die Funktion
STANDBY kann nur als Einzel-Funktion
FUNCTION e This parameter defines the configuration
profile of the CGW board. If HG3570
functionality is used, it must be
configured at first position. If a
functions HG3530, HG3540 or HG3550
is desired, this function must be at the
end of the profile just suffixed by the
according HG35xxR value. The function
STANDBY can only be configured as
single function.
BSSU WTIME d Bei RESTART-Kommando: Wartezeit
zwischen Aus- und Wiedereinschalten
in Sekunden.
WTIME e For RESTART command: Wait time
between switching off and switching on
in seconds.
Possible values: 0-20
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs

Language
CGWB SMODE=NORMAL d Standby Mode oder Normal Mode
Eine Baugruppe im Normal Mode hat
gültige Baugruppendaten und
normalerweise auch OPTIIPs
konfiguriert.
Eine Baugruppe im Standby Ready
Mode hat keine gültigen
Baugruppendaten, auf diese Baugruppe
können OPTIIPs umgeschaltet werden,
falls eine andere Baugruppe aus
demselben Baugruppen-Pool (AMO
BPOOL) defekt wurde.
Eine Baugruppe im Standby Defekt
Mode hat ebenfalls keine gültigen
aufgrund eines Defekts seine OPTIIPs
und seine Baugruppendaten
abgegeben.
SMODE=NORMAL e Standby Mode or Normal Mode
A board in Normal Mode has valid board
data and normally also OPTIIPs
assigned to it.
A board in Standby Ready Mode has no
valid board data, to this board OPTIIPs
can be switched over if another board of
the same board reconfiguration pool
(AMO BPOOL) becomes defective.
A board in Standby Defect Mode has
also no valid board data, this board has
lost its OPTIIPs and its board data to
another board because it's gone
defective.
IPADR d IP Adresse der Common Gateway
Baugruppe (Source Adresse)
IPADR e Source IP address of common gateway
board
MTYP=INITCGWB d Zurücksetzen der Konfigurationsdaten
der Common Gateway Baugruppe auf
die Standardwerte
MTYPE=INITCGWB e Reset configuration data of common
gateway board to default values
NETMASK d IP-Netzmaske des LAN-Segmentes. Die
IP-Netzmaske bestimmt die Grenze
zwischen Netz- und Host-Teil in der IP-
Adresse. Alle IP-Adressen am LAN-
Segment müssen bezüglich des
Netzanteils der IP-Adresse gleich und
bezüglich des Host-Teils unterschiedlich
sein (auch der Default Router muss
dieser Bedingung entsprechen).
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs

Language
NETMASK e IP net mask of LAN segment The IP net
mask determines the network and the
host partition of an IP address. All IP
addresses of a LAN segment must
contain the identical network addresss
part but different host address parts
(also the Default Router must fulfill this
requirement)
DIMSU CGW d Anzahl der Common Gateway-
Baugruppen
CGW e Number of common gateway boards
TYP=APPLIKAT d DIMSU-Option: Applikation
TYPE=APPLICAT e DIMSU options: application
WSPROT d Sprach/Daten Applikation mit
Workstation Protokoll
WSPROT e integrated voice/data application using
workstation prot.
SBCSU ANSCHL=IP2 d Anschluss-Art der Geräte
IP2=Anschluss ueber IP (HFA Gateway
Version 2)
CONN=IP2 e Device Connection Type
IP2=Connection via IP (HFA gateway
version 2)
ART=OPTI d Hauptrufnummer des IP-
Telefonanschluss einrichten
OPT=OPTI e Specification of bus type or unit to be
expanded
GERKON=OPTIIP d Geräte-Konstellation eines Teilnehmers
OPTIIP=IP Sprachterminal
DVCFIG=OPTIIP e Device Configuration
OPTIIP=Digital IP voice terminal
IPPASSW d passwort fuer ip login prozedur
IPPASSW e Password for IP logon procedure
SNU d Standard Tastaturbelegung
STD e Standard Key Layout
ZAND APIMAX d Maximale Anzahl der gleichzeitig
aktiven API Sessions. DB-Initialisierung:
10
APIMAX e Maximum number of allowable active
API sessions. DB initialization: 10
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs

Language
KENNL d Linearisierungs- und
Kompandierungskennlinien bei der
PCM-Kodierung/Dekodierung. Der
eingegebene Wert wird zum einen in die
zentralen Anlagendaten übernommen,
zum anderen bei eingerichteter LTG
auch in die entsprechenden COFI-
Daten. Der Wert in den zentralen
Anlagendaten ist auch gültig bei der
Konfiguration von NCUI-Baugruppen in
NBCS-Shelfs.Es sollte daher nach
Konfiguration von NBCS-Shelfs dieser
Wert nicht mehr geändert werden!
CODE e Speech coding.The entered value will be
issued once to central system data and
once for assigned LTG in the according
COFI-data. The value in central system
data is also valid for configuration of
NCUI-boards in NBCS shelfs. Therefore
this value should not be changed after
configuration of NBCS-shelfs!
TYP=CIT d Konfigurieren von fiktiven Geräten,
Einstellungen für API Schnittstelle
TYPE=CIT e Configure virtual stations, settings for
API interface
TYP=CONFC d Länderspezifische Einstellung für
KENNL, K- oder TDAEMPF. Dieser
Zweig gilt nur für kompakte Hardware.
TYPE=CONFC e Selection of country-specific settings for
CODE, CONFAT STNAT. This branch is
only for compact hardware.
A31003-H3160-S104-8-7620, 07/2014
Application Example
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
hfa_03_faq.fm
Frequently Asked Questions
3 Frequently Asked Questions

1. Question: How far can an IP phone be located from the host?
Answer: There are no hard distance limitations. However delays limit the
practical distance:
The larger the distance between the host and the IP workpoint, the more
delay is introduced via the underlying network. If possible one way delays
should be less than 200ms.
2. Question: How many IP phones are supported per HiPath 4000?

Answer: Up to 12000 IP phones can be supported per HiPath 4000. Note that
the HG 3500 is supported on all IP Access Points.
3. Question: How many IP phones can be supported per HG 3500?

Answer: A maximum of 240 IP phones can be supported per HG 3500.
Depending on the traffic requirements of the subscribers either a 60
connection GW or a 120 connection GW will be required.
4. Question: Are calls between IP phones switched in the IP network?

Answer: Yes. HG 3500 gateways support peer-to-peer (IP switching).
5. Question: Do IP phones connected to HG 3500 gateways support mobility?

Answer: Yes. The following is possible:
• The user can take an IP phone to a new office or location and all
relevant information is transferred automatically and no manual
intervention is necessary.
• A user can log in from any location via a soft-client to his workpoint,
which will automatically disconnect itself from the HiPath 4000
gateway. The soft-client will provide the user with the same features
and privileges as the standard workpoint.
• A user can log in from any IP phone within a system or CorNet

network and make this phone his temporary phone. The home phone
will automatically be logged off and calls to the home phone are
forwarded as defined for CFNR (Call Forwarding No Reply). The
temporary phone will provide the user with the same features and
privileges as the standard home workpoint.
6. Question: Do the Phones require static IP addresses?

Answer: No, the current version of the HG 3500 line gateway does support
clients configured for DHCP. Note that a DHCP server has to be configured
in the IP network; otherwise static IP addresses are required for all clients.
7. Question: Can I connect a user via a wireless connection?
A31003-H3160-S104-8-7620, 07/2014
hfa_03_faq.fm
Answer: Yes. Given that IP line gateways support standard TCP/IP protocol
and have been designed to work over WAN links only excessive delays are a
concern. Make sure that wireless transceivers are working like Ethernet
bridges in order to minimize delays.
8. Question: When payload and/or signaling IP packets arrive out of sequence,

are they automatically re-arranged?
Answer: As long as all the relevant payload IP packets are still held within the
jitter buffer, out of sequence IP packets will be re-arranged automatically.
Given that signaling is using TCP/IP out of sequence packets are correctly
processed by the protocol.
9. Question: Which protocols are we using for signaling and QOS?

Answer: Signaling: TCP/IP, 
QOS: LAN-tagging according IEEE 802.1p/q; DiffServ according to RFC
2474.
10. Question: Is the H.323 fast connect procedure implemented on the HG

3500?
Answer: Yes, in order to minimize call setup time, the H.323 fast connect
procedure is used to exchange H.245 logical channel information.
11. Question: If IP network is down and the 4000 does not see the IP phones
what do callers get when calling?
Answer: If connectivity to the IP phone is lost, the phone will be in a reset
state trying to reconnect to the gatekeeper. There is a display indicating that
state. There will be no dial tone. Incoming calls can be re-directed using the
feature “Alternate Routing On Error” that can use LCR rules for forwarding the
call to anything you like, e.g. to PhoneMail.
12. Question: Do we have QoS/payload monitoring of the DMC connection?

Answer: No, the HG 3500 is not aware of DMC connections.
13. Question: How long does it take for IP phones to re-register with a standby
gateway?
Answer: Based on performance testing with standby HG 3500s, it takes
approximately 2 - 3 minutes for 240 phones to re-register onto a backup card.
14. Question: Why can’t we support more than 240 users on the 120 connection
version?
Answer: Based on traffic values you could support over 600 users at 6 C.C.S
and 1% blocking. However you would not be able to support the signaling
traffic required for that many users. Customers would not configure that many
users on a single card for reliability reasons either.
A31003-H3160-S104-8-7620, 07/2014
hfa_03_faq.fm
15. Question: The effect of default setting recommended by popular router

manufacturers and the TOS byte default values documented for HFA, that is,
the pre-defined DiffServ CodePoints (DSCP) is exactly the opposite of the
intended effect. The packets we marked as high priority are rejected
straightaway by the router. What is this nonsense about?
Answer: The default values used for HFA come from an internal company
standard that was implemented in all HG 35xx gateways. The interoperability
problem has since come to light with the result that the company standard will
be modified shortly.
The default values can be modified at any time and modified in line with actual
conditions in the customer network.
16. Question: Does HFA support VLANs?

Answer: Yes but only in conjunction with priority tagging. In accordance with
IEEE 802.1 p/q, tagging was introduced for HFA to support priority tagging. If
tagging is activated then the permanently preset priority bits of the various
types of traffic are always set. If tagging is active, the VLAN ID can also be
set (default value is zero). VLAN ID is not supported without the set priority
bits.
17. Question: Does HFA support subnetting (RFC 950)?

Answer: Yes. When the network mask is entered, a check is performed to
determine whether the block of ones that has been set meets the minimum
length required for the class of the address, i.e. 8 ones for Class A, 16 for B
and 24 for C. If the number of ones is greater than the number required for
the class, subnetting is activated.
18. Question: Does HG 3500 gateway (STMI2/STM4) supports

ClassLessInterDomainRouting (CIDR), this means Subnetting/Supernetting?
Answer: Yes.
19. Question: Does vHG 3500 gateway (HiPath 4000 Softgate) supports
ClassLessInterDomainRouting (CIDR), this means Subnetting/Supernetting?
A31003-H3160-S104-8-7620, 07/2014
hfa_03_faq.fm
A31003-H3160-S104-8-7620, 07/2014
mobhfa_01_feature_description.fm
Feature Description
Mobile HFA Logon
Mobile HFA Logon
1.1 Mobility Session

This feature is an enhancement to the static HFA (HiPath Feature Access).
The idea of mobile HFA is to use the characteristics (classmarks, name, number,
keys, ...) of one subscriber (mobile user) on different phones, which might be
spread all over the world. We call such a user a “mobile user”.
The mobile user has a phone at his home office and travels to another place
(other office or an other country). There he uses a phone (visited phone) as a
visitor. He enters a code for the activation of “Mobile HFA” , his home number, his
PIN and a possible password to use the visited phone with the characteristics of
his phone at home.
If this procedure ends successfully (sufficient classmarks, phone types, ...) his
home phone is placed in an out of order state (forced log off). The mobile user
can then use the visited phone like his home phone. E.g. the home phone
number/name are displayed if a call is established by or to the mobile user, the
home phone’s classmarks are valid ...
If the visitor cancels the mobile HFA logon by a logoff, the orginal characteristics
of the home phone and the visited phone are reactivated. The time between a
mobile HFA logon and logoff at a visited phone is called “mobility session”.
The owner of the visited phone is no longer reachable in this case. All calls to the
owner of the visited phone are redirected to a CFNR destination.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Mobility Session
Activation of feature
subscriber Stefan (Munich)

22097 34456
subscriber Jones (London)
22097 Phone Display 34456
Stefan travels to London and uses Jones’ phone for mobile HFA Logon
Move
forced logoff? 22097
Figure 1 Activation of feature
All calls dialed for 34456 are now forwarded to the system CFNR (Call
forwarding no reply) for subscriber Jones (admin by AMO ZIEL).
If Stefan travels back to Munich he performs the mobile logoff in London (DAR or
menu) , or if he forgets he can also cancel it in Munich. In both cases the orginal
status of both phones are redone within seconds.
While the London phone is in mobile use nobody can use Stefan’s device in
Munich.
Any call to Jones does not ring at Jones’ device.
The feature can be protected against misuse with passwords, feature blocking
and line dependent classmarks.
Call to mobile user
London
Munich
(Stefan’s home switch)
device rings!
Alex calls Stefan Alex
Alex does not see on his display Stefan picks up and

that Stefan picks up in London talks to Alex
Figure 2 Call to mobile user
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Shared Desk Area
Call to visited phone
London
Jeff calls Jones

not ringing
Jeff’s call is redirected to system CFNR

(mailbox or other phone )
22097
Figure 3 Call to visited phone
1.2 Shared Desk Area

Based on the feature “Mobile HFA Logon“,the functionality “Shared Desk Area“
can be used. The Shared Desk Area is a scenario, that allows a dynamic
assignment of telephone devices to users. At a switch a number of users without
fix phones, and phones with virtual subscribers are configured. The phones
are spread over various rooms or buildings. The number of phones might be
significantly lower than the number of users.
The real users can use any phone of the Desk Area. One terminal can be used
by different users one after another.
E.g. user Jones can use a phone starting at 9.00 am. User Jeffrey can use the
same phone afterwards when Jones has left the office. Both users can use the
same phone using their own user characteristics.
User Jones comes to a phone and logs on with own phone number and
password. If the logon succeeds he can phone as “Jones“.
His session is canceled if he logs off or if another user (Jeffrey) logs on to this
phone.
After a logoff the phone comes up as configured. For this reason any physical
phone must be configured with a virtual subscriber number (Dummy Number).
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Shared Desk Area
Office 1 Office 2
Desk 1 Desk 1 Desk 2
If a user logs off or his session is canceled by another user logging on at the
device this user turns into visited state. That is that any call to him is redirected to
the system CFNR destination.
In the following example phone numbers starting with “3” indicate users of the
shared desk areas configured at the switch. The dummies for the telephones
have “names” like “office1 desk12” and corrresponding numbers starting with “2”:
20112 (=office1, desk 12).
Jeffrey 32245 (not in office)
34456 34457 20112
Jones Wilson desk 12

logged on at loggen on at
desk 12 desk 11
Jones and Wilson are logged on at the phones at desk10 and desk 11.
Calls to ...
Name Number Action
Jeffrey 32245 are redirected to System CFNR
Jones 34456 ring at desk phone 10
Wilson 34457 ring at desk phone 11
desk10 20110 are redirected to System CFNR
desk12 20112 ring at desk phone 12
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Shared Desk Area
Now user Jeffrey logs on at desk phone 11 (knocks out Wilson). Jones logs off
and moves to desk 12 for logon.
Wilson 34457 (not in office)
20110 32245 34456
office 1 at desk 10 Jeffrey Jones

loggen on at logged on at
desk 11 desk 12
Calls to ...
Name Number Action
Jeffrey 32245 ring at desk phone 11
Jones 34456 ring at desk phone 12
Wilson 34457 are redirected to System CFNR
desk10 20110 ring at desk phone 10
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Shared Desk Area
A31003-H3160-S104-8-7620, 07/2014
mobhfa_02_user_interface.fm
User Interface
Activation/Deactivation via DAR
2 User Interface
IMPORTANT: For mobility and shared desk area the procedures for activation
and deactivation are identical!
The user has two possibilities to activate a mobile logon:
• via DAR (Digit analysis Result) and
• via service menu.
A third possibility works for admin only: The administration via AMO ACTDA.
2.1 Activation/Deactivation via DAR

The feature via DAR is activated/deactivated at the visited phone.
2.1.1 HFA Logon

Enter the DAR for mobile HFA logon.
Then the user is asked to enter his home number (terminate with #) and his PIN
(terminate with #).
Display says “MOBILE HFA LOGON STARTED”. If all checks run ok soon his own
display on the home phone is displayed. As it he was really at home.
If the checks do not run ok (wrong password, wrong home number, missing
attributes, ...) the rejection is shown on display.
• Mobility session (home phone physicall extended)

The home phone displays “Forced Logoff - Cancel mobility?” and is not
usable, even not for fire brigade or other emergency calls. The only possible
action is to cancel the mobility. But this action is protected by password
(phone password - not the same as mobility password).
• Shared Desk Area (No physical home phone)

If the home phone does not exist physically nothing can be displayed on the
home. No cancelation from home phone is possible.
2.1.2 HFA Logoff

To logoff enter the DAR for logoff.
A31003-H3160-S104-8-7620, 07/2014
mobhfa_02_user_interface.fm
User Interface
Activation via menu
The display says “MOBILE HFA LOGOFF STARTED ... “
Soon afterwards the visitors own display comes up again at the visited phone and
the home user’s phone comes up at the home switch.
2.2 Activation via menu

The menu items “MOBILE HFA LOGON/LOGOFF” for mobile HFA are located in
the service menu. Activate the service menu at the visited phone and step
forward/backward with the buttons “<“ and “>” until the menu items for mobile
HFA logon/logoff are reached.
The mobile HFA feature can also be reached with service menue and digit
“8’”(mobile HFA logon) and digit “9” (mobile HFA logoff).
After confirming logon the user is asked to enter home number and PIN like
above.
After confirming an action the behaviour is the same like DAR activation.
2.3 Activation with AMO ACTDA

AMO ACTDA needs three parameters. visited number, home number and PIN.
The Activation with AMO ACTDA is only possible at the switch where the visited
phone is configured.
The AMO displays a message if logon runs ok or if it fails (with a reason).
A31003-H3160-S104-8-7620, 07/2014
mobhfa_03_prerequisites.fm
Prerequisites
3 Prerequisites
This feature is restricted with different flags in the switch of the visited phone and
the switch of the home phone.
Possible phones for mobile HFA

The feature does not work with any type of phone. Both phones must have the
capacity for mobile HFA in their firmware. Currently the following phones have
this functionality:
• optipoint 410 (not 410 entry),
• optipoint 420 (electronic labeling keys)
• optipoint 600
• OpenStage 20/20G/40/40G/60/60G/80/80G
IMPORTANT: If the OpenStage terminal is operated in combination with an

optiClient, "optiPoint 420 advance" must be set as the device type in the
optiClient. For more information, refer to Section 4.1.1, “OpenStage terminal
in combination with an optiClient”.
AMO prerequisites
• AMO FEASU bit MOBHFA must be set on both sides.
• The home phone must have the line attribute MHFAHOME in AMO SDAT.
• The visited phone must have the line attribute MHFATBV (to be visited) in
AMO SDAT.
• For the home phone a PIN must be installed with COPIN attribute MOBILE.
Hardware
The mobile HFA phones are connected to the common gateway board (STMI2/4
board).
Password settings
For the mobile user a mobile password should be added. This password
prevents the “forced logoff“ at the home station from being cancelled without a
password.
• optiPoint terminals
The password is assigned in the terminal Configuration menu, submenu
“02=System”.
• OpenStage terminals
A31003-H3160-S104-8-7620, 07/2014
mobhfa_03_prerequisites.fm
Prerequisites
The password can be asigned via the WBM of the terminal (Administrator
Pages > User mobility > Cancel mobility passowrd) or directly at the
terminal via the menu Admin > Password > Mobility.
A31003-H3160-S104-8-7620, 07/2014
mobhfa_04_service_info.fm
Service Information
Mobile HFA in Connection with other Features
4.1 Mobile HFA in Connection with other Features
4.1.1 OpenStage terminal in combination with an

optiClient
General hints for the configuration of an optiClient together with an
openStage phone
• The OpenStage of type "nn" has to be configured with the fitting standard key
layout "openStage nn".
• It is not allowed to change the key assignment for an OpenStage phone (AMO
TAPRO) while the optiClient is active.
• The individual change of key settings by the subscriber must not be enabled
for the combination optiClient/openStage.
• When the user previously owned the combination optiClient/optiPoint then

he/she is to be informed about the new key layout which can be seen in the
optiClient application. Reason for this are the fixed key functions at
OpenStage phones.
• In case of disregarding the mentioned restrictions the proper key assignment

cannot assured when changing from OpenStage to optiClient and vice versa.
This can be repaired only with deleting and configuring the complete
connection again.
• This procedure counts also for the so called Tandem-Mode (optiClient uses
the same number like the home station. In this case is the home station the
OpenStage!)
Configuration of a new optiClient/OpenStage connection

• New configuration of the openStage phone with the proper standard key
layout together with the configuration of the optiClient (OPTIIP&API).
• The device "optipoint 420 advance" has to be chosen in the optiClient

application.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Mobile HFA in Connection with other Features
Replacement of an existing optiClient/optiPoint configuration with

optiClient/OpenStage
1. Regeneration of the user data
2. Delete the connection completely
IMPORTANT: The deletion is necessary because it is currently the exclusive

way to delete the so-called shadow table for key assignments. If it is not
cleared correctly, the proper key assignment is not assured neither at the
optiClient nor at the OpenStage. It depends on what had happened at the
connection previously (i.e. different phone types were connected etc.) if the
shadow table has to be cleared.
3. Now you can exchange the phones and then configure the OpenStage as
described in General hints for the configuration of an optiClient together with
an openStage phone or do it vice versa.
IMPORTANT: For additional information, refer to "’Mobile Registration’ with

OpenStage Hardware Terminals" in the optiClient readme file.
4.1.2 Malicious Call Identification at visited switch

If the feature “Malicious Call Identification” is activated at the visited switch (AMO
PERSI) then the attempts for logon that fail because of wrong password entered,
are output on the service terminal of the visited switch.
The output warning looks like this:

F2754 M4 N0063 MC TRACE BPA PIN TRACE 04-02-10 13:25:12
STNO INTERN:3581 PIN:25587
FORMAT:34
Read: At station 3581 a logon was attempted with PIN 25887.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Please refer to the documentation of „Signaling and Payload Encryption“Restriction
4.1.3 Signaling and Payload Encryption (SPE)
4.2 Please refer to the documentation of „Signaling and Payload Encryption“Restriction
optiClient does not support the „Mobile HFA Logon“ feature. The user can realize
this feature using different user profiles for logon. Users wchich want to use
different calling numbers have to work with different user profiles.
4.3 Language Support

The feature works with the language of the home switch. That means that menu
and display texts, which are controlled by the switch software, are displayed in
the switch language („Please dial“, „Enter password“,..).
Any messages controlled by the phone firmware (directly, not switch dependent)
are only English („Cancel logoff“ , „logging on to home...“).
If the switch language is not set to English, texts are displayed in two languages.
4.4 Logon Sequences
A31003-H3160-S104-8-7620, 07/2014
Service Information
Logon Sequences
A31003-H3160-S104-8-7620, 07/2014
mobhfa_05_configuration.fm
Generation
Example 1: Two HFA subscribers in the same Host
5 Generation
IMPORTANT: Important time interval

After all AM commands to install Mobile HFA are executed wait 3 minutes before
starting a mobile HFA logon. HFA boards and IP phones need up to 3 minutes to
perform a self-initialization. If a HFA logon is attempted before the self initalization
has passed successfully, this logon will possibly fail.
• Preparation
– Preparation: Reserve memory for boards and subscriber
– Add board data
– Add subscriber data
– Add authorizations and classmarks for feature, subscriber ...
– Add DARs
– Add call forwarding destinations
– Others
5.1 Example 1: Two HFA subscribers in the same Host

The subscriber 2150 shall get the right to be able to identify himself at the terminal
of subscriber 2160. The subsriber 2160 shall not get any possibility of the
identification. An incoming call for 2160 should be forwarded to subscriber 4444,
if 2150 is using the phone of 2160.
optiPoint IP
Teilnehmer: 2160
IP
HG 3500-1 IP
Gateway: HG 3500-1
IP
optiPoint IP
LAN IP
Teilnehmer: 2150
Gateway: HG 3500-1
HiPath 4000
A31003-H3160-S104-8-7620, 07/2014
Generation
Example 2: Two HFA subscriber at different systems
CHANGE-
; /* Configuration of 30 HG 3530 circuits with 30 b-channels
X“,FCTID=1,LWVAR=“0“,FCTBLK=1,ALARMNO=0;
ADD-
55.255.0;
ADD-SBCSU:STNO=2150,OPT=OPTI,CONN=IP2,PEN=1-3-85-
0,DVCFIG=OPTIIP, ...;
1,DVCFIG=OPTIIP, ...
ADD-WABE:CD=*95,DAR=MHFALGON,CHECK=N;
ADD-WABE:CD=*96,DAR=MHFALGOF,CHECK=N;
ADD-
PERSI:TYPE=STN,STNO=2150,NAME=“STEFAN*“,PIN1=“258861“,PININDIV=Y
;
CHANGE-PERSI:TYPE=COPIN,COPIN=1,COTYPE=MOBILE, ...;
CHANGE-SDAT:STNO=2150,TYPE=ATTRIBUT,AATTR=MHFAHOME;
CHANGE-SDAT:STNO=2160,TYPE=ATTRIBUT,AATTR=MHFATBV;
CHANGE-FEASU:TYPE=A,CM=MOBHFA;
ADD-
ZIEL:TYPE=FWD,SRCNO=2160,SI=VOICE,DESTNOF=4444,DTYPE=CFNR,ITYPE=
GEN,CFVAR=SYSTEM;
REGENERATE-RICHT;
5.2 Example 2: Two HFA subscriber at different systems

The two subscribers 2150 and 2160 shall get the rights to be able to identify
themselves at the
terminal of the other subscriber. The calls for 2160 should be forwarded to his
mobile number 017544444444, if his phone is used as “Mobile HFA Logon”. The
calls for 2150 should be forwarded to the subscriber 4444, if his phone is used as
“Mobile HFA Logon”.
A31003-H3160-S104-8-7620, 07/2014
Generation
Example 2: Two HFA subscriber at different systems
HG 3500-2 optiPoint IP
IP
IP LAN Subscriberr: 2160

Gateway: HG 3500-2
System 2 WAN
HG 3500-1
optiPoint IP
IP LAN IP
Subscriber: 2150
Gateway: HG 3500-1
System 1
Generation of the System 1:

CHANGE-
ADD-
55.255.0;
RESTART-BSSU:ADRART=LAGE,LTU=3,EBT=85;
0,DVCFIG=OPTIIP,....;
ADD-PERSI:TYPE=STN,STNO=2150,NAME=“OPTI IP
1*“,PIN1=“0512“,PININDIV=YES;
CHANGE-PERSI:TYPE=COPIN,COPIN=1,COTYPE=MOBILE,....;
ADD-
ZIEL:TYPE=FWD,SRCNO=2150,SI=VCE,DESTNOF=4444,DTYPE=CFNR,ITYPE=GE
N,CFVAR=SYSTEM;
REGENERATE-RICHT;
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs
Generation of the system 2:

CHANGE-
ADD-
55.255.0;
0,DVCFIG=OPTIIP,...;
ADD-PERSI:TYPE=STN,STNO=2160,NAME=“OPTI IP
10*“,PIN1=“0612“,PININDIV=YES;
CHANGE-PERSI:TYPE=COPIN,COPIN=1,COTYPE=MOBILE,.....;
ADD-
ZIEL:TYPE=FWD,SRCNO=2160,SI=VCE,DESTNOF=0017544444444,DTYPE=CFNR
,ITYPE=GEN,CFVAR=SYSTEM;
REGENERATE-RICHT;
5.3 Relevant AMOs

Language
ACTDA ABMED=GERFREI d Erlaubt das Abmelden nur im Freizustand.
COND=IDLESTN e Allows the logoff only if station is idle.
ABMED=UNBED d Erlaubt das Abmelden in jedem Fall.
COND=UNCOND e Condition for logoff: Unconditional logoff
ACTION=MLOGO d Aktivieren des Leistungsmerkmals: Logon
N eines Mobile HFA-users
ACTION=MLOGO e Activate the feature: Logon of mobile hfa-
N user
ACTION=MLOGOF d Deaktivieren des Leistungsmerkmals:
F Logoff eines Mobile HFA-users
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
ACTION=MLOGOF e Deactivate the feature: Logoff of mobile hfa-
F user
BESRNR d Rufnummer des besuchten Teilnehmers
VISSTNO e Station number of the visited station
HEIMPIN d PIN des Besuchers
HOMEPIN e PIN of the visitor
HEIMRNR d Heimrufnummer des Besuchers
HOMESTNO e Home station no. of the visitor
BKAN3530 d Anzahl der B-Kanaele fuer die HG3530
Funktion
BCHN2430 e Number of b-channels for HG3530 function
FCTID d Function Id ist immer 1
FCTID e Function id is always set to 1
wählen)
FCTBLK e Function block index (choose a free function
block between 1-20)
LWVAR d Index auf Loadware Block der T1
Baugruppe
LWVAR e Loadware variant
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
TYP=IPGW d IP Gateway (Common Gateway
Baugruppe)
BCHLCNT e Defines the number of b-channels related to
the selected function.
selected function.
BGBKAN d Block fuer Baugruppe mit 60 und/oder 120
B-Kanaelen
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
BRDBCHL e Dedicates the block for boards with 60 and/
or 120 b-channels.
CONFIG=WEITER d Weitere Block-Konfiguration ermöglichen
CONFIG=CONT e Continue block configuration
CONFIG=OK e Terminate block configuration
FCTBLK e This index describes the function block
which should be configured on the CGW
board. With that index the amount of
needed physical lines (board circuits) is
calculated.
Gateways fest. Dabei muss die eventuell
benötigte HG 3570 Funktion als erste
angeführt werden. Falls ein bestimmter
Line-Bereich für die Funktionen HG 3530
oder HG 3550 vorreserviert werden soll,
muss die entsprechende Funktion am Ende
stehen und mit dem Wert HG35xxR
abgeschlossen sein. Die Funktion
STANDBY kann nur als Einzel-Funktion
profile of the common gateway board. If
HG3570 functionality is used, it must be
functions HG3530, HG3540 or HG3550 is
desired, this function must be at the end of
the profile just suffixed by the according
HG35xxR value. The function STANDBY
can only be configured as single function.
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
CGWB SMODE=NORMAL d Standby Mode oder Normal Mode
Eine Baugruppe im Normal Mode hat
gültige Baugruppendaten und
normalerweise auch OPTIIPs konfiguriert.
Eine Baugruppe im Standby Ready Mode
hat keine gültigen Baugruppendaten, auf
diese Baugruppe können OPTIIPs
umgeschaltet werden, falls eine andere
Baugruppe aus demselben Baugruppen-
Pool (AMO BPOOL) defekt wurde. Eine
Baugruppe im Standby Defekt Mode hat
ebenfalls keine gültigen Baugruppendaten,
diese Baugruppe hat aufgrund eines
Defekts seine OPTIIPs und seine
Baugruppendaten abgegeben.
data and normally also OPTIIPs assigned to
it. A board in Standby Ready Mode has no
valid board data, to this board OPTIIPs can
be switched over if another board of the
same board reconfiguration pool (AMO
BPOOL) becomes defective. A board in
Standby Defect Mode has also no valid
board data, this board has lost its OPTIIPs
and its board data to another board because
it's gone defective.
IPADR e Source IP address of common gateway
board
bezüglich des Netzanteils der IP-Adresse
gleich und bezüglich des Host-Teils
unterschiedlich sein (auch der Default
Router muss dieser Bedingung
entsprechen).
partition of an IP address. All IP addresses
of a LAN segment must contain the identical
DIMSU CGW d Speicherreservierung für eine Common
Gateway Baugruppe und Baugruppen
bezogene Teilnehmerdaten
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
CGW e Number common gateway boards
FEASU LM d LM=MOBHFA
CM e CM=MOBHFA
TYP d TYP=FREI
Aktivieren des Leistungsmerkmals
TYPE e TYPE=A
Activate the feature
PERSI COPIN d Class of PIN
COPIN e Class of PIN
PIN1 d PIN (Passowrt für HFA)
PIN1 e PIN (password for HFA)
PINTYP d PINTYP=MOBIL
COPIN-Typ fuer netzweiten Transfer der
COPIN im CorNet Protokoll
COTYPE e COTYPE=MOBILE
COPIN type
RUFNU d Rufnummer des Teilnehmers
STNO e Station number
TYP=COPIN d Mindestens eine COPIN (1-15) muss das
Attribut Mobil haben.
TYPE=COPIN e At least one COPIN (1-15) must have the
attribute Mobile.
TYP=TLN d Teilnehemr einrichten
TYPE=STN e add a station
SBCSU ANSCHL=IP2 d Anschluss-Art der Geräte
IP2=Anschluss ueber IP (HFA Gateway
Version 2)
CONN=IP2 e Device Connection Type
IP2=Connection via IP (HFA gateway
version 2)
ART=OPTI d Hauptrufnummer des IP-Telefonanschluss
einrichten
e
GERKON=OPTIIP d Geräte-Konstellation eines Teilnehmers
OPTIIP=IP Sprachterminal
DVCFIG=OPTIIP e Device Configuration
OPTIIP=Digital IP voice terminal
IPPASSW d passwort fuer ip login prozedur
IPPASSW e Password for IP logon procedure
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
SDAT EMERK d EMERK=MHFAMOE
Merkmal des Heinat-Telefons
EMERK=MHFATBV
Merkmal des “besuchten“ Telefons
AATTR e AATTR=MHFAMOE
HFA home phone of visitor
AATTR=MHFATBV
mobile HFA phone which can be visited
TLNNU d Teilnehmerrufnummer
STNO e Station number
Typ d TYP=MERKMAL
Teilnehmermerkmale administrieren
ATTRIBUT e TYPE=ATTRIBUT
Administrate subscriber attributes
(service=voice)
WABE KZP=MFALGON d Kennzahlpunkt für Aktivierung
DAR=MFALGON e Logon by a mobile hfa subscriber

KZP=MFALGOF d Kennzahlpunkt für Deaktivierung
DAR=MFALGOF e Logoff by a mobile hfa subscriber
PRUEF d Prüfumfang
CHECK e Scope of check
RNR d 2 Rufnummern für Aktivierung /
Deaktivierung (*95/*96)
CD e 2 station numbers for activation /
deactivation (*95/*96)
VKS d Verkehrssituation
(5 = Teilnehmer-Vorwahl)
CPS e Call progress state
WABE d WABE-Gruppe
DPLN e Feature access group
ZAND APIMAX d Maximale Anzahl der gleichzeitig aktiven
API Sessions. DB-Initialisierung: 10
APIMAX e Maximum number of allowable active API
sessions.
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
KENNL d Linearisierungs- und
Kompandierungskennlinien bei der PCM-
Kodierung/Dekodierung. Der eingegebene
Wert wird zum einen in die zentralen
Anlagendaten übernommen, zum anderen
bei eingerichteter LTG auch in die
entsprechenden COFI-Daten. Der Wert in
den zentralen Anlagendaten ist auch gültig
bei der Konfiguration von NCUI-
Baugruppen in IPDA-Shelfs.Es sollte daher
nach Konfiguration von IPDA-Shelfs dieser
Wert nicht mehr geändert werden!
CODE e Speech coding.The entered value will be
issued once to central system data and
once for assigned LTG in the according
COFI-data. The value in central system data
is also valid for configuration of NCUI-
boards in IPDA shelfs. Therefore this value
should not be changed after configuration of
IPDA-shelfs!
TYP=CIT d Konfigurieren von fiktiven Geräten,
Einstellungen für API Schnittstelle
TYPE=CIT e Configure virtual stations, settings for API
interface
TYP=CONFC d Länderspezifische Einstellung für KENNL,
K- oder TDAEMPF. Dieser Zweig gilt nur für
kompakte Hardware.
TYPE=CONFC e Selection of country-specific settings for
CODE, CONFAT STNAT. This branch is
only for compact hardware.
ZIEL AULVAR=SYSTEM d Systemumleitung
CFVAR=SYSTEM e system call forwarding
KART d KART=GEN (alle Anrufe)
Kommende Belegungsart des AUL-Zieles
ITYPE e ITYPE=GEN (all calls)
incoming seizure of fwd feature
QLRUFNU d Quellenrufnummer
SRCNO e station number of source
SI=VOICE d Service Sprache
SI=VCE e service voice
TYP=AUL d Verbindungstyp Anrufumleitung
TYPE=FWD e Call Forwarding
UART=CFNR d Anrufumlenkung bei nicht melden
DTYPE=CFNR e call forwarding no reply
ZLRUFNU d Zielrufnummer
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs

Language
DESTNOF e destination number for forwarding
A31003-H3160-S104-8-7620, 07/2014
Generation
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
01_ipda_feature_desc.fm
IPDA Feature Description
IP Distributed Architecture (IPDA)
IP Distributed Architecture (IPDA)
1 IPDA Feature Description

HiPath 4000 offers the possibility of distributing access points across an IP
network. These access points are shelves which accommodate the standard
HiPath 4000 access modules. The subscriber line circuits at the access points
are handled precisely as if they were linked directly - as has been customary in
the past - to a HiPath 4000 switch. Administration of all components distributed
via IP is also realized as one system via an access point of the HiPath 4000
system.
HG HG Peripheral
3500 3575 Boards
AP 3300 IP
HG
HiPath 4000 LAN segment
3500
IP Networ k
Peripheral
Boards
HG Peripheral
3575 Boards
Public AP 3500/3505 IP
Network Control
Public
HiPath 4000 Network
Figure 1 Overview of architecture
The “IP distributed architecture“ comprises the following main components:
• HiPath 4000 The communication server, which also controls all

components of the “IP Distributed Architecture“. The rich
volume of call processing features is thus also available to
the “IP Distributed Architecture“.
• HG 3500 This IP gateway module allows payload connections
between subscriber line/CO and tie trunk circuits in the
central part of the HiPath 4000 system and subscriber/CO
and tie trunk circuits in the distributed access points.
• IP Access Points There are three types of IP based access points
• AP 3300 IP This traditional Flexpack shelf with IP integration offers 16
slots for HiPath 4000 peripheral modules
• AP 3500 IP1 This new 19“ shelf (3 units high), which can be mounted in
a 19“ rack, allows inexpensive configurations for small
locations. As a basic box, it offers 3 slots for HiPath 4000
peripheral modules. The number of slots can be increased
to 7 with an AP 3505 IP expansion box (3 units high). Both
the AP 3500 IP and the AP 3505 IP expansion box can be
equipped with a redundant power supply.
A31003-H3160-S104-8-7620, 07/2014
Scalable Increase in System Capacity
• AP 3700 IP This 19“ shelf (10 units high), which can be mounted in a
19“ rack, features nine slots for HiPath 4000 peripheral
boards. The frame comes with three PSU modules which
are operated in a 2+1 redundancy configuration.
It can also take over autonomous control in emergencies
within the context of the Access Point Emergency feature.
Both types of access point are equipped with a HG 3575 connection module, which
establishes the connection to the IP infrastructure (10/100BT).
The IP-based access points allow the use of the majority of current and future
modules which can be operated in classic HiPath 4000 shelves.
• HiPath 4000 The HiPath 4000 SoftGate provides cost-effective branch
SoftGate offices with reliable HiPath 4000 survivability options and
an easy IT integration in the HiPath 4000 solution and
management suite. This software application offers full
HiPath Feature Access (HFA) for IP Endpoints, SIP
Service Provider connectivity and native SIP connectivity
for trunking and subscriber with basic feature set based
upon a standard server.
Any HiPath 4000 SoftGate site integrates seamless in the
communication system and network like an IPDA Access
Point (AP 3700 IP) - in terms of features and
administration.
1 For upgrade to HiPath 4000 V6 a project-specific release is required.
The HG 3500 and HG 3575 modules are each equipped with two 10/100BT
Ethernet connections for connecting to the IP network.
1.1 Scalable Increase in System Capacity

HiPath 4000 supports up to 83 access points linked via IP (AP 3300 IP, AP 3500/
3505 IP or AP 3700 IP), in addition to a maximum of 15 directly linked shelves
(AP 3300 or AP 3700).
Thus, the maximum number of digital subscriber line circuits in a system can be
increased to 12000.
1.2 Distributed Circuit Switching

With HiPath 4000, the circuit switching of the payload (B channels) is not limited
to the central switching network
• Calls within IP-based access points are switched to a local TDM switching
network directly and, consequently, without runtime in the IP network. The
switching network on the HG 3575 module has a capacity of 256 channels.
• Calls between different IP-based access points are switched in the IP

network.
A31003-H3160-S104-8-7620, 07/2014
Time Synchronization
• Calls which go beyond IP-based access points are switched both in the IP
network and in the central HiPath 4000 system.
1.3 Time Synchronization

An exact time is required for many HiPath 4000 functions (call detail recording,
time-dependent channels, night service, etc.). All clocks in the system (up to 84)
have to operate synchronously.
There are two ways of synchronizing the time:
1. The IP network has a time server, which supports time synchronization of all
HiPath 4000 processors (the central processor and all survivability units)
using the Network Time Protocol.
2. A time server is not available in the IP network. The HiPath 4000 plattform
then makes its local time available over the network for synchronizing all
survivability units.
For more information on setting the date and time and the time synchronization
please refer to the documentation HiPath 4000 V6, Installation, Configuration
and Migration, Installation Guide.
1.4 Call Scenarios

In order to gain a better understanding of the call processing procedures and their
distribution across the components of the IP distributed architecture, a couple of
typical call scenarios are described below.
1.4.1 Internal Access Point Call
Figure 2 Signaling for an internal access point call
A31003-H3160-S104-8-7620, 07/2014
Call Scenarios
Signaling from and to the connected telephones is always transmitted over the IP
network to the call processing infrastructure in the HiPath 4000 central system,
and from there back again.
Figure 3 Voice link (payload) for an internal access point call
The central call processing infrastructure establishes the voice link and makes all
features available. In this case, the voice link is switched within the access point
in the TDM-based switching network of the HG 3575 module. This means that
no payload is generated in the IP network and none of the channels of the
transport capacity from the access point to the IP network are occupied.
1.4.2 Call Between Two Access Points
Figure 4 Signaling for an access point  access point call
Signaling from and to the connected telephones is always transmitted over the IP
network to the call processing infrastructure in the HiPath 4000 central system,
and from there back again.
A31003-H3160-S104-8-7620, 07/2014
Call Scenarios
Figure 5 Voice link (payload) for an access point  access point call
features available. In this case, the voice link between the two access points is
switched in the IP network with the aid of the HG 3575 modules. Each of the
access points occupies one channel of the available transport capacity to the IP
network.
1.4.3 Call Between an Access Point and the Central

System
Figure 6 Signaling for an access point  central system call
Signaling from and to the connected telephone in the access point is always
transmitted over the IP network to the call processing infrastructure in the HiPath
4000 central system, and from there back again.
A31003-H3160-S104-8-7620, 07/2014
Call Scenarios
Figure 7 Voice link (payload) for an access point  central system call
features available. The voice link from the access point is switched to the IP
network with the aid of the HG 3575 module. The HG 3500 module functions as
a gateway and converts the IP data stream back into a PCM data stream that can
be processed by the central system. This data stream is transferred to the
connected subscriber within the central system. The call is therefore switched in
both the IP network and in the HiPath 4000 central system. The access point and
the gateway module each occupy one channel of the available transport capacity
to the IP network.
1.4.4 Trunk Access / Networking
Figure 8 Trunk Access/Networking
Local trunk access can also be set up in an access point. The least cost routing
function of the HiPath 4000 decides which trunk access to use based on the
subscriber’s location.
A31003-H3160-S104-8-7620, 07/2014
Survivability for Signaling and Payload
1.5 Survivability for Signaling and Payload

In the basic configuration (without the survivability features), an IPDA installation
function depends completely on the availability and reliability of the LAN/WAN
infrastructure used. The failure of an access point's IP connection leads to failure
of the access point.
Total failure of the IP infrastructure leads to the failure of all access points. Only
the central system and the "classic" peripheral units connected continue to work.
Survivability for signaling and payload ensures that HiPath 4000 also offers the
greatest availability in distributed operation. The public telephone network/an
alternative LAN connection (in the case of Signaling Survivability) can be used as
an alternative route in the event of an IP network failure or if the IP network
temporarily fails to provide the requisite quality for voice transmission.
Figure 9 Survivability: failure in the IP network
If the IP connection from an access point/HiPath 4000 SoftGate to the central

system fails, there can be no interaction between the access point/HiPath 4000
SoftGate and the central system. Messages from the terminal devices and trunks
in the access point/HiPath 4000 SoftGate are temporarily buffered on the (v)HG
3575, while messages from the central system are buffered in the central
processor. If the duration of the failure exceeds a definable limit, the Access
Point/HiPath 4000 SoftGate is reset, thereby disconnecting all calls.
A31003-H3160-S104-8-7620, 07/2014
Survivability for Signaling and Payload
1.5.1 Signaling Survivability
Figure 10 Signaling survivability examples: Signaling via PSTN
Signaling survivability takes over control of the Access Point/HiPath 4000

SoftGate if signaling is no longer possible via the IP network.
For more information, see Section 2.6, “Signaling Survivability”.
1.5.2 Payload Survivability
Figure 11 Payload survivability: Alternative route for the payload via PSTN
A31003-H3160-S104-8-7620, 07/2014
Signaling and Payload Separation (SPS)
Payload survivability allows internal system calls to be routed via the CO. The
HiPath 4000 in effect "calls itself" and establishes an internal call between
different parts of the system. The route for payload survivability is also selected
automatically as a spillover route if the entire capacity of the HG 3575 is already
in use in the IP network.
IMPORTANT: For information about feature restrictions with payload surviv-

ability, see
1.6 Signaling and Payload Separation (SPS)
1.6.1 Feature Description

“Signaling and Payload Separation” which enables HiPath 4000 in an IPDA
environment to split the path of the network traffic in the meaning of
• signaling from host system (call control) to the access point is routed over the
IP customer network (Enterprise WAN).
• payload is routed over the PSTN Network using payload survivability

connections.
Signaling and payload separation is based on the existing survivability solution

and therefore the signaling path is routed in the same way as in earlier HiPath
4000 versions. The payload (RTP-Stream) is routed across connections built up
from WAML or ISDN-Router via PSTN-Lines between the locations.
1.6.2 Prerequisites
• Central office connectivity via ISDN- lines.
• Signaling and payload connections has to be built up via WAML or external

ISDN-Router.
• Bandwidth limitation has to be performed by the Resource Manager.
• Signaling and payload separation is restricted to star topology/IPDA-infra-

structures.
• Using HG 3500 separate boards are needed for trunking and WAML functio-
nality.
A31003-H3160-S104-8-7620, 07/2014
• Currently only 8 static routes can be configured on the HG 3500. Therefore

the number of subnets for the APs is limited. In the worst case (each AP in
another subnet, no combination of subnets via the netmask possible) this
limits the amount of AP's using SPS without an external router to 8. In addition
only 8 WAMLs can be used in the host.
• Delays in signaling may cause wrong interpretation with a result of wrong call
treatment and can affect the features behavior (e.g. Hunt group, call pick up
groups)
• Due to the fact, that in call pickup scenarios there is no connection before the
picking user performs the pickup, cut trough times might be longer in SPS
scenarios
• Payload separation is destination oriented and restricted to one HiPath 4000

system. If other systems are connected to the HiPath 4000 no networking
features will be supported (e.g. network wide pick-up).
• Different trunk groups must be configured for payload separation without

intercept parameters.
1.6.3 Configuration
For informationen on the configuration please refer to Section 2.10, “Signaling
and Payload Separation (SPS)”.

For increased resilience, IPDA V2.0 boards HG 3500 and HG 3575 should be
connected with two LAN cables to different switches (please refer to Section 6.4,
“Redundant LAN Interface”).
1.8 Different Time Zones (DTZ)

The “Different Time Zones (DTZ)“ feature is used in situations when an IPDA
shelf or access point (AP-IP) or HFA IP telephones are located in different time
zones than the host system. In these cases, the local time of day should be shown
instead of the system time on the display of the digital telephones that are
connected to the remote AP or on the display of the HFA IP telephones.
For a detailed description, refer to the section „Different Time Zones (DTZ)“.
A31003-H3160-S104-8-7620, 07/2014
A-Law/µ-Law Conversion in AP Shelf
1.9 A-Law/µ-Law Conversion in AP Shelf

It is possible to connect telephones in AP shelves that work with companding
algorithms different to the host system (e.g. host system in Germany (A-law),
access point in the USA (µ-law)).
For a detailed description, refer to Section 2.15, “A-Law/µ-Law Conversion in AP

Shelf”.
1.10 Different Announcements, Tones and MFV DialTone Receivers per

Access Point
With HiPath 4000 V6 it is possible to configure different languages/countries for
each access point with AMO UCSU. Therefore different access points can have
the same or different SIU-Init-Data files.
For a detailed description, refer to Section 2.16, “Different Announcements,

Tones and DTMF DialTone Receivers per Access Point”.
1.11 Additional Features

• High voice quality
On account of longer voice signal delays caused by the system in the IP
network, voice quality will be impaired by echo unless this is removed prior to
transmission. The HG 3500 and HG 3575 modules therefore feature an
integrated echo canceller.
Lower bandwidth requirements
If voice is transmitted via IP in uncompressed form (pursuant to G.711), the
bandwidth requirement is greater than in the case of ISDN on account of the
packaging in the IP protocol.
If less bandwidth is to be occupied, the voice signal can be compressed. HG
3500 and HG 3575 offer optional compression pursuant to the G.729A
standard (only 8 Kbps, instead of 64). Furthermore, additional bandwidth can
be saved by suppressing voice pauses. Silence suppression suppresses the
transmission of silence on the line. (G.729AB, or G.711 Annex 2)
• Support for Quality of Service in the IP network through prioritization

HiPath 4000 IP distributed architecture supports prioritization in the IP
network on the basis of the following standards:
• IEEE 802.1 p/q (VLAN Tagging) on Layer 2
• IETF RFC 2474 (DiffServ) on the IP Layer
A31003-H3160-S104-8-7620, 07/2014
Additional Features
• Transport capacity in the IP network

HG 3500 and HG 3575 can transmit up to 120 B channels simultaneously
over the IP network regardless of the hardware and configuration in use (see
"Gateways HG 3500 and HG 3575, Section 3.6, “B Channels”).
• Support of network management on the basis of SNMP

HG 3500 and HG 3575 support network management on the basis of the
SNMP protocol. Statistical data from the applicable standard MIBs and
additional data from proprietary MIBs can be queried.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Configuring the IPDA Feature
2 Configuring the IPDA Feature

IP distributed architecture is rather a platform expansion than a typical new
feature. Therefore, the configuration of this feature is broken down in the following
section into typical steps, which are to be performed in consecutive sequence:
• Configuration: HiPath 4000 LAN segment - Section 2.1, “HiPath 4000 LAN
Segment”
• Configuration: Access Point (networked or direct link) - Section 2.2, “Access

Point”
• Configuration: HG 3500 as HG 3570 - Section 2.3, “HG 3500 as HG3570 in

the HiPath 4000 System”
• Configuration: Subscriber, trunk and tie trunk connections in access points -

Section 2.4, “Subscriber, CO/Tie Trunk Circuits in Access Points”
If necessary, the following steps are performed subsequently:
• Configuration: Special routes - Section 2.5, “Special Routes”
• Configuration: Signaling survivability - Section 2.6, “Signaling Survivability”
• Configuration: Quality monitoring for the signaling connection over IP -

Section 2.7, “Quality Monitoring for the Signaling Connection over IP”
• Configuration: Source dependent routing - Section 2.8, “Source Dependent

Routing”
• Configuration: Payload survivability - Section 2.9, “Payload Survivability”
• Signaling and payload separation - Section 2.10, “Signaling and Payload

Separation (SPS)”
• Divert call in survivability mode to another access point - Section 2.11, “Divert
Call in Survivability Mode to another Access Point”
• Configuration: External music on hold - Section 2.12, “External Music on

Hold”
• Information on CMI - Section 2.13, “Information on CMI”
• Configuration: IP address changes - Section 2.14, “IP Address Changes”

These notes must be observed if the IP addresses in the HiPath 4000 LAN
segment are to be changed in an active system (for example, because the
network carrier changes the network address).
• Configuration: a-law/µ-law conversion - Section 2.15, “A-Law/µ-Law

Conversion in AP Shelf”
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• Configuration: Different announcements, tones, DTMF dial tone receivers per

access point - Section 2.16, “Different Announcements, Tones and DTMF
DialTone Receivers per Access Point”.
The corresponding sections contain configuration examples and detailed

explanations of all requisite AMOs and AMO parameters. A distinction is made
between
configuration with Configuration Manager and
configuration with AMO.
The creation of the “Access point Emergency“ feature is described in “Access

Point Emergency (APE)”, Chapter 2, “Configuring the APE Feature (Access Point
Emergency)”.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
HiPath 4000 LAN Segment
2.1 HiPath 4000 LAN Segment

The HiPath 4000 LAN segment is that part of the customer network in which the
IP components of the central system and direct link (i.e. not via router) access
points are installed.
DEFRT
AP 99
192.168.1.254
STMI-1 STMI-2
Peripheral
HG HG Boards
3500 3575
Ra Rx
AP 3300 IP, AP 3500/3505
Router Router
HG
H iPat h 40 00 LA N Seg ment
3500
I P N e two r k
AP 98
Peripheral
HG Boards
Peripheral 3575
Boards
NETADR
192.168.1.0 AP 3300 IP, AP 3500/3505
Ry
NETMASK Router
ADP 255.255.255.0
AP 43
Peripheral
Atlantic LAN
HG Boards
3575
CCAADR
192.168.1.1 AP 3300 IP, AP 3500/3505
CC-A R1
Router PS T N N e t wo r k
CCBADR SURVNET
Peripheral
AP 18
192.168.1.2 192.168.15.0 HG Boards
CC-B R10 3575
Router
AP 3300 IP, AP 3500/3505
CSTA
Peripheral
Assistant HG Boards AP 17
3575
AP 3300 IP, AP 3500/3505
HiPath
4000
Figure 12 HiPath 4000 LAN segment
ADD-SIPCO: NETADDR=192.168.1.0, NETMASK=255.255.255.0,

IPMODE=IPV4, DEFRT=192.168.1.254,
CCAADDR=192.168.1.1, CCBADDR=192.168.1.2,
SURVNET=192.168.15.0;
At maximum capacity, a configuration requires a considerable number of IP

addresses in this network, namely.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• CC-A, CC-B, ADP: 3

• HiPath 4000 Assistant: 1
• HiPath 4000 CSTA: 1
• HG 3500: Up to 83
• Directly linked HG 3575: Up to 83
• Survivability routers: Up to 10
Therefore, it is advisable to configure a dedicated LAN segment for the central

part of a large HiPath 4000 installation and not permit any more nodes within that
segment (particularly file servers, etc.)
For demo installations in which the HiPath 4000 LAN segment remains isolated,
IP addresses from the private address range pursuant to RFC 1597 can be used.
These do not require international coordination. For example, the range from
192.168.1.1 to 192.168.1.255 with netmask 255.255.255.0 can be recommended
as the Class C address range.
Generation
Addresses (LSNET)
The first step in configuring IP distributed architecture involves the configuration
of the HiPath 4000 LAN segment.
Configuration:
Data
Click Search, enter the required IP addresses and Save.
ADD-SIPCO:NETADDR=192.168.1.0,NETMASK=255.255.255.0,
DEFRT=192.168.1.254,IPMODE=IPV4,CCAADDR=192.168.1.1,
CCBADDR=192.168.1.2,SURVNET=192.168.15.0;
IMPORTANT: Although the CCA/CCB address already had to be entered when

the configuration was performed with the LAN Wizard, it has to be configured
again here with AMO SIPCO.
If an isolated configuration is to be set up, the default router must be configured

with the zero address 0.0.0.0. In this case, only “direct link“ access points can
be configured (see Section 2.2.2, “Configuring a “Direct Link“ Access Point”). In
Figure 12 “HiPath 4000 LAN segment”, Router Ra is the default router.
If there is no second processor, the CCBADDR parameter need not be specified.
The SURVNET parameter can be dispensed with if signaling survivability is not

required. If, however, the customer has purchased signaling survivability, i.e. if
the corresponding license counter is greater than zero, then a survivability
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
network address (see section Signaling Survivability) must be specified. This

can also be achieved with a dummy entry (zero address 0.0.0.0), though the
signaling survivability function is not available in this case.
The licenses for signaling survivability can be queried as follows:
Configuration Management --> HiPath Inventory Management

--> HIM System Data --> Feature --> Marketing Units
Click Search --> Sales Features tab --> Signaling Survivability entry
DISP-CODEW; “SIGNALING SURVIVABILITY“ entry
The values specified with ADD-SIPCO are immediately valid.
IMPORTANT: Prior to ADD-SIPCO, use ping to check that the IP addresses

given to you by the administrator are reachable.
CCAADDR and CCBADDR must not be reachable as this would indicate that the
corresponding address had already been assigned.
DEFRT must be reachable (if not 0.0.0.0).
IMPORTANT: Following ADD-SIPCO the active processor must be reachable in

its network segment.
The standby processor in duplex systems does not respond (as long as it is in
standby mode). Since routes have not yet been configured, the active processor
cannot answer ping requests from other network segments!
Change:
All parameters configured here can be changed later.
Data
Click Search, change the addresses and Save.
CHANGE-SIPCO:TYPE=LSNET;
The parameters are not immediately effective after the CHANGE, but only once
the system has been restarted. The database must be backed up beforehand to
disk.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
The restart can only be performed in expert mode.

Expert Mode --> HiPath 4000 Expert Access --> Open ...<IP> with AMO 
(see AMO command)
EXEC-UPDAT:BP,ALL;
EXEC-REST:SYSTEM,RESTART;
IMPORTANT: Changing the IP address has multifarious effects on a running

system. If changes are necessary, a strict change sequence must be complied
with, or else the access points will be irrevocably disconnected. 
In this context, see Section 2.14, “IP Address Changes”.
Delete:
If, for instance, IPDA is to be completely removed from the system after a test, all
access points and HG 3500, as well as the SIPCO configuration, also have to be
deleted after the uninstall routine is completed. The links/LAN modules for the
HiPath 4000 LAN segment can then also be removed. You must restart the
system.
Deletion can only be performed in expert mode.

(see AMO command)
DELETE-SIPCO;
List of AMO parameters for Add / Change:

Language
SIPCO NETADR d Netzadresse des HiPath 4000 LAN Segments
gilt für CC-A, CC-B, alle HG 3500 (STMI2/4),
Default-Router, Survivability-Router und direkt
angeschlossene Access Points
NETADDR e Network Address of the HiPath 4000 LAN Segment
valid for CC-A, CC-B, every HG 3500 (STMI2/4),
default router, survivability router and directly linked
Access Points
NETMASK d Netzmaske des HiPath 4000 LAN Segments
gültig wie NETADR
NETMASK e Netmask of the HiPath 4000 LAN Segment
valid like NETADDR
Table 1 AMO SIPCO parameters in ADD branch or for CHANGE under

TYPE=LSNET
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
DEFRT d Default-Router im HiPath 4000 LAN Segment
über diesen Router sollen alle nicht direkt im HiPath
4000 LAN Segment angeschlossenen Access
Points von den HG 3500 Baugruppen erreicht
werden. Angegeben wird die IP-Adresse der
Routers im HiPath 4000 LAN Segment.
Falls kein Default-Router benutzt werden soll, z. B.
für isolierte Demo-Installationen mit “direct link“
APs, muss die Adresse 0.0.0.0 angegeben werden.
DEFRT e Default Router in the HiPath 4000 LAN Segment
via this router all Access Points that are not directly
linked to the HiPath 4000 LAN Segment shall be
reached by all HG 3500 boards.. The IP address of
this router in the HiPath 4000 LAN Segment is to be
given.
If no default router shall be used, e.g. for stand-
alone demo installations with “direct link“ APs, give
the address 0.0.0.0.
IPMODE d IP Mode. Muss für IPDA IPV4 sein.
IPMODE e IP mode. Must be set to IPV4 for IPDA.
CCAADR d IP-Adresse des CC-A Prozessors im HiPath 4000
LAN Segment
CCAADDR e IP address of the CC-A Prozessor in the HiPath
4000 LAN Segment
CCBADR d IP-Adresse des CC-B Prozessors im HiPath 4000
LAN Segment
Nicht angeben, wenn kein CC-B im System
CCBADDR e IP address of the CC-B Prozessor in the HiPath
4000 LAN Segment
Omit, if no CC-B in the system
SURVNET d Netzadresse des Survivability Netzes
Die Netzmaske für das Survivability Netz ist mit
255.255.255.0 ebenso fest vorgegeben wie die
Adressierung der einzelnen Knoten. Die
Survivability-Router 1..10 haben die Adressen
1..10, die Access Points 17..99 die Adressen 17..99
im letzten Byte.
Die vorgegebene Netzmaske schränkt die Klasse
(A,B oder C) der Netzadresse nicht ein. Das
Survivability Netz kann ein Subnetz eines Klasse A
Netzes mit Netzmaske 255.255.255.0 sein.
TYPE=LSNET
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SURVNET e Network Address of the Survivability Network
The netmask for the Survivability Network is fixed to
255.255.255.0 as well as the individual node
adresses. The survivability routers 1..10 are
addressed 1..10, Access Points 17..99 have
address 17..99 in the last byte.
The given netmask does not limitate the class (A,B
or C) of the network address. The Survivability
Network can be a subnet of a class A network with
netmask 255.255.255.0.
TYPE=LSNET
Quality of Service Parameters (DIFFSERV)

The following parameters can be set:
– For QoS support on Layer 2 to IEEE 802.1 q/q [VLAN, VLANID]
– For QoS support on Layer 3 to IETF RFC 2474 (DiffServ) 

[TOSPL, TOSSIGNL]
– the lowest port used for payload connections (UDP/RTP+RTCP)

[UDPPORT]
The Ethernet interface setting must be identical for all connected interface
partners (CC-A and CC-B or LAN switches, routers).
“Autonegotiate“ setting of the other partner.
Caution: Incorrect settings cannot normally be detected by the system and
therefore go unreported. If one device is operating in full duplex and the other in
half duplex mode, this is not immediately noticeable. Where there is a high
payload, the device set to half duplex will report a higher number of late collisions
and the packet delay will increase sharply.
If the LAN ports with which CC-A and CC-B are connected do not support autone-
gotiation, or if autonegotiation does not function reliably, the Ethernet interfaces
of the central processors can be set to fixed values.
VLAN tagging should only be activated when all routers in the network segment
of the access point support VLAN tagging. The same applies for the DiffServ
CodePoints. If the routers do not support DiffServ, the standard TOS values must
be configured without DiffServ. If DiffServ is supported, but not the CodePoints,
the values specified by the network carrier must be configured.
Given that some network component vendors only support prioritization with
VLAN ID > 0 pursuant to IEEE 802.1 p/q, the VLAN ID can also be set. The HG
3575 module generally sets the priority bits when the VLAN option is activated.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
For values, see Table 3 “TOS values” in document “Gateways HG 3500 and HG
3575”. According to the standard, the VLAN ID must then be set to zero, which
also happens for the default setting.
The parameters for configuring the TOS bytes for the various traffic types are
provisioned with the DiffServ CodePoints pursuant to the company’s QoS
Recommendation. VLAN tagging pursuant to IEEE 802.1 p/q is deactivated
(VLAN=NO).
If VLAN tagging pursuant to IEEE 802.1 p/q is supported in the HiPath 4000 LAN
segment, it can be activated as follows:
Data
Click Search, activate the VLAN Tagging checkbox under Type of
Service on the System Data tab, then Save.
CHANGE-SIPCO:TYPE=DIFFSERV,VLAN=YES;
If DiffServ is not supported, the TOS bytes must be configured with content
pursuant to RFC 791 (see Table 3 “TOS values” in document “Gateways HG 3500
and HG 3575”).
Data
Click Search, enter the TOS values under Type of Service on the System
Data tab, then Save.
CHANGE-SIPCO:TYPE=DIFFSERV,TOSPL=16,TOSSIGNL=20;
If either the VLAN or VLANID parameter has been changed, an update must be
performed on the hard disk and then the system must be restarted.
Configuration Management --> Network --> System

Click Save on the Action pull-down menu.
The restart can only be performed in expert mode.
(see AMO command)
Note:
VLAN tagging changes the packet header. Many L2 switches or routers
understand either packets with or without tagging. In other words,
• the relevant switches/routers also have to be adjusted.
• while the settings do not correspond, it is possible that packets will not be
transmitted.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• the conversion of the HG 3500 system interrupts payload connections
• the conversion of the HiPath 4000 CCs interrupts the contact to all access
points
A change of TOSPL is directly loaded on all HG 3500s and becomes effective

immediately, without the operation of the modules having to be interrupted.
The parameter TOSSIGNL does not become effective until the connection for
which the TOS value is set has been cleared down and then set up again.
The disconnection and re-establishment of the links between the HiPath 4000
central system and access point can be realized through
• a soft restart on the HiPath 4000 system, which then affects all subscribers
The soft restart can only be performed in expert mode.

Expert Mode --> HiPath 4000 Expert Access --> Open ...<IP> with
AMO (see AMO command)
EXEC-REST:UNIT,BP,SOFT;
• through DEACTIVATE-USSU and ACTIVATE-USSU for every individual

access point, which then only affects the respective subscribers.
Configuration Management --> System Data --> IPDA --> IPDA

Access Point
Click SEARCH and select the access point.
Click Deactivate on the Action pull-down menu.
Once the system has confirmed deactivation of the AP, reactivate it with
Activate.
DEACTIVATE-USSU:LTU=xx;
ACTIVATE-USSU:UNIT=LTG,LTU=xx;
The TOS bytes at the access points are configured specifically for every access
point.
If you want to locate the payload connections in a customer network in a specific

port range for reasons of port-based prioritization, for example, then this can be
set as follows:
Data
Click Search, enter the base address of the UDP port under Type of
Service on the System Data tab, then Save.
CHANGE-SIPCO:TYPE=DIFFSERV,UDPPORT=40000;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SIPCO TOSPL d TOS-Byte für die VoIP Payload-Verbindungen
zwischen HiPath 4000 und Access Point.
Gültig für Pakete von beliebigen HG 3500 in
Richtung Access Point.
TOSPL e TOS Byte for the VoIP payload connections
between HiPath 4000 and Access Point.
Valid for packets from any HG 3500 towards
Access Point.
TOSSIGNL d TOS-Byte für die Signalisierungsverbindungen
zwischen HiPath 4000 und Access Point. (auch
für Supervisory und RTO)
Gültig für Pakete vom CC-A, CC-B in Richtung
Access Point.
TOSSIGNL e TOS Byte for the Signaling connections between
HiPath 4000 and Access Point. (also for
Supervisory and RTO)
Valid for packets from CC-A, CC-B towards
Access Point.
VLAN d Schaltet VLAN-Tagging nach IEE 802.1p/q ein
(JA) bzw. aus (NEIN).
Gültig für VoIP Payload-Verbindungen von
beliebigen HG 3500 in Richtung Access Point.
Gültig für Pakete vom CC-A, CC-B in Richtung
Access Point.
VLAN e Switches VLAN Tagging according to IEEE
802.1p/q on (YES) or off (NO).
Valid for VoIP payload connections from any HG
3500 towards Access Point.
Valid for packets from CC-A, CC-B towards
Access Point.
VLANID d VLAN-ID Wert für alle HG 3500 sowie CC-A und
CC-B
Nur von Bedeutung, wenn VLAN=JA.
12 Bit Wert, der gemäß IEEE 802.1 p/q Standard
auf Null gesetzt sein muss, wenn Priorisierung
verwendet wird (VLAN=JA).
Von dieser Standardeinstellung darf nur
abgewichen werden, wenn
Netzwerkkomponenten bestimmter Hersteller
erzwingen, dass bei Nutzung der Priorisierung
eine VLAN-ID > 0 zu verwenden ist.
Table 2 AMO SIPCO parameters in CHANGE branch under

TYPE=DIFFSERV
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
VLANID e VLAN-ID value for all HG 3500, CC-A and CC-B
Only relevant if VLAN=YES.
12 Bit value that, according to IEEE 802.1 p/q, has
to be set to zero when prioritization is used
(VLAN=YES).
This standard setting may only be changed, if
network components of certain vendors enforce
the usage of VLAN-ID > 0 while using
prioritization.
UDPPORT d Einstellung des Basis-Ports (niedrigste
Portnummer) für Payloadverbindungen im IPDA-
System
Für jede Payload-Verbindung werden an den
beteiligten Gateways HG 3500 bzw. HG 3575 ein
UDP Port für RTP und ein weiterer für RTCP
benötigt. Die Portnummern werden in einem
Bereich von [UDPPORT .. UDPPORT+247]
vergeben.
RTP belegt dabei immer eine gerade Nummer,
RTCP die nächst höhere ungerade.
Wertebereich: [4352 .. 65038], nur gerade Zahlen
erlaubt.
UDPPORT e Setting of the Base Port (lowest port number) for
Payload Connections in the IPDA System
For every payload connection one UDP port is
required for RTP and another for RTCP. The port
numbers are assigned in a range of [UDPPORT ..
UDPPORT+247].
RTP always uses an even number, RTCP the next
higher odd one.
Value range: [4352 .. 65038], only even numbers
allowed.
TYPE=DIFFSERV
Additional parameters
With ADD-SIPCO, additional system parameters are also set to default values
which can be changed by means of CHANGE-SIPCO. These parameters are
broken down into 2 groups.
System timing (TIMING)

Under TYPE=TIMING, central values of the system timing can be set for the
monitoring of IP links. If the values set here are exceeded, the system switches
the communication between HiPath 4000 and access point to the “signaling
survivability“ modem link or the access point is temporarily put out of operation.
In order to render the changed values in the affected access points effective, they
all have to be restarted with
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Data
Click Execute on the Action pull-down menu and select the mode of action
Update AP, confirm with OK.
EXEC-USSU:MODE=UPDATAP,LTU=xx;

system hard disk. Otherwise, the data on the system would conflict with the data
on the HG 3575 when the system is reloaded and could only be synchronized
again with EXEC-USSU:UPDATAP,LTU number,UL.
If the PINGTIME parameter has been changed, all HG 3500s must also be
restarted with

Board Maintenance
Click Search and select all STMI2 and STMI4.
with OK.
RESTART-BSSU:ADDRTYPE=PARTNO,PARTNO=Q2316-X;
and
RESTART-BSSU:ADDRTYPE=PARTNO,PARTNO=Q2316-X10;
and
and
IMPORTANT: It is crucial that TIMING changes are really loaded at all access
points and HG 3500s, as otherwise the system reaction to the timer sequences
would be inconsistent!
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SIPCO PINGTIME d Zeitdauer, während der nach einer schlechten VoIP
Payload-Verbindung zwischen 2 HG 3500/HG 3575
die Verbindungsqualität getestet wird.
Ist die Verbindungsqualität bei Beendigung einer
Verbindung zwischen 2 HG 3500/75 als schlecht
markiert, wird für die Zeitdauer PINGTIME die
Verbindung getestet. Fällt während dieser Zeit die
Prüfung gut aus, wird die Prüfung abgebrochen und
die Verbindung zwischen den betroffenen HG 3500/
75 sofort wieder auf gut gesetzt. Ist das Ergebnis
schlecht, wird während der gesamten Zeit weiter
geprüft und erst nach Ablauf der PINGTIME die
Verbindung auf gut gesetzt wird. Weitere
Informationen siehe Figure 26 “Blocks the IP
connection for payload due to „Bad Quality“”.
Der Wert wird in [s], Sekunden angegeben.
Es wird empfohlen, diesen Parameter vom
Default-Wert 60 auf den Maximalwert 3600 zu
verändern.
PINGTIME e Time interval for testing the payload quality between
2 HG 3500/HG 3575 after a VoIP payload connection
has been terminated with quality marked bad.
Is the payload quality for a connection between 2 HG
3500/75 marked as bad upon termination of the
connection, the connection is going to be tested for
the duration of PINGTIME. With positive test results
during this time interval the test ist stopped
immediately and the connection is marked good
again. With negative results the tests will be
continued until PINGTIME expires. After that the
connection will be marked good again. For further
Information see Figure 26 “Blocks the IP connection
for payload due to „Bad Quality“”
The value is entered in [s], seconds.
It is recommended to change this parameter from
the default value 60 to the maximum value of
3600.
Table 3 AMO SIPCO parameters in CHANGE branch under TYPE=TIMING
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
RESTIME d Zeit zwischen einem Schnittstellenfehler aus dem
“Keep Alive” der Signalisierungsverbindung und dem
Rücksetzen des Access Points (Wartezeit bis AP-
Restart).
Wird ein Schnittstellenfehler des “Keep Alive” der
Signalisierungsverbindung gemeldet, startet das
Zeitintervall RESTIME.
Nach dem Schnittstellenfehler können keine neuen
Gespräche vom/zu den betroffenen AP aufgebaut
werden; bestehende Verbindungen bleiben
abhängig vom IP-Netzwerk bestehen, jedoch kann
es zu Nullwegen (100% Paktetloss) kommen.
Nach Ablauf des Zeitintervalls wird der Access Point
zurückgesetzt. Alle Payload-Verbindungen gehen
verloren, es sind keine neuen Payload-
Verbindungen möglich, bis es der HiPath 4000
Zentrale wieder gelingt, Kontakt zum Access Point
herzustellen.
RESTIME e Time between an interface fault specified in the
"Keep Alive" message from the signaling link and the
access point reset.
The RESTIME interval starts when an interface fault
is reported in the "Keep Alive" message from the
signaling link.
New calls cannot be set up from/to the relevant AP
following the interface fault; existing connections are
maintained depending on the IP network, but null
paths can occur (100% packet loss).
The access point is reset when the time interval
expires. All payload connections are lost and no
payload connections are available until the HiPath
4000 central system succeeds in establishing
contact with the access point.
The value is specified in seconds [s].
SUPVTIME d Maximale Zeitdauer, während der auf ein Paket auf
der Überwachungsverbindung (Supervisory-
Verbindung) gewartet wird.
Nur bei aktivierter Signaling Survivability. Auf der
Supervisory-Verbindung werden in sehr kurzen
Intervallen “Keep Alive” Meldungen gesendet.
Kommt für länger als SUPVTIME kein Paket an, wird
der Weg über das IP-Netz als gestört betrachtet, die
Modemverbindung zum Access Point aktiviert und
dieser Weg für die Signalisierungsverbindung
zwischen HiPath 4000 und Access Point verwendet.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SUPVTIME e Maximum time waiting for a packet on the
Supervisory connection
Only if Signaling Survivability is activated. On the
Supervisory connection “keep alive” messages are
sent in very short intervals. If SUPVTIME exceeds
without a packet arrived, the way through the IP
networks is considered as disturbed. The modem
connection to the Access Point is activated. The
signaling between HiPath 4000 and Access Point is
routed via the modem connection.
The value is entered in [s], seconds.
APESWDL d APE Umschalteverzögerung
Y nur wirksam mit dem Leistungsmerkmal AP
Emergency!
siehe “Access Point Emergency” > Section 2.10,
“Defining the Switchover Delay”
Das Umschalten eines Access Points in den
Emergency Mode kann um eine konfigurierbare Zeit
verzögert werden.
Es ist entweder Null - “schalte sofort“ einzutragen,
oder die Zeit, welche von der HiPath 4000 Zentrale
benötigt wird, um einen RELOAD durchzuführen.
Der Wert wird in Minuten angegeben. Wertebereich
[0 .. 99].
APESWDL e APE Switch Over Delay
Y only effective with the feature AP Emergency!
see “Access Point Emergency” > Section 2.10,
“Defining the Switchover Delay”
The switch-over of an Access Point into Emergency
Mode can be delayed for a configurable amount of
time.
It shall either be set to zero - “switch immediately“, or
to the amount of time which the central HiPath 4000
system needs to perform a RELOAD.
The value is entered in minutes. Range [0 .. 99].
ALVTIME d Maximale Zeitdauer für den “Keep Alive”
Mechanismus der Signalisierungsverbindungen
zwischen HiPath 4000 und den Access Points.
Vergeht diese Zeit ohne Antwort, wird ein
Schnittstellenfehler gemeldet und der Access Point
wird aus der ATTENDANCE LIST genommen
(F5308, LTUC OUT OF ATTENDANCE LIST).
Wertebereich [20 .. 90]
Hinweis:
Wenn Signaling Survivability konfiguriert ist, muss
dieser Parameter auf einen Wert eingestellt werden,
der größer ist als die Maximalzeit für den kompletten
Aufbau der Signalisierungsverbindung über Modem!
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
ALVTIME e Maximum time interval for the “keep alive”
mechanism of the signaling connections between
HiPath 4000 and the Access Points.
If there is no answer during this interval, an interface
error will be reported and the access point is taken
out of the ATTENDANCE LIST (F5308, LTUC OUT
OF ATTENDANCE LIST).
The value is entered in [s], seconds. Range [20 .. 90].
Note:
When Signaling Survivability is configured, this
parameter must be set to a value greater than the
maximium duration of the complete setup of
signaling connection via modem!
Payload Quality (PLQUAL)

Under TYPE=PLQUAL the limiting values for monitoring the payload quality, i.e.
the voice links, are configured. If the upper limits are exceeded, additional voice
links between the respective modules (HG 3500 and/or 3575) are established via
the alternative route, provided one has been configured. If the lower limits are
exceeded, the standard route is returned to the IP network.
The delay values only ever refer to one direction (A -> B or B -> A), and not to the
“round-trip delay“ (A -> B -> A). They are derived from the Real Time
Transmission Control Protocol.
Data
Click Search, enter the limiting values under Payload Quality on the
System Data tab and Save.
CHANGE-SIPCO:TYPE=PLQUAL,DLYHILIM=200,DLYLOLIM=120,
LFRHILIM=3,LFRLOLIM=2;
The changed parameters are started on all access points and HG 3500s
immediately and without interrupting operation.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SIPCO DLYHILIM d Obere Grenze für die Verzögerung der VoIP
Payload-Verbindung zwischen HG 3500/HG 3575.
Bei Überschreiten dieses Wertes wird die
Verbindung zwischen den 2 betroffenen HG 3500/75
als schlecht markiert. Künftige Verbindungen
zwischen diesen HG 3500/75 werden solange über
einen Alternativweg geführt (sofern einer eingerichtet
ist), bis die Verbindung wieder auf gut gesetzt wird.
Der Wert wird in [ms], Millisekunden eingegeben.
DLYHILIM e Upper delay limit for VoIP payload connections
between HG 3500/HG 3575.
When delay exceeds this value, the connection
between the 2 involved HG 3500/75 is marked as
bad. Future connections between these HG 3500/75
will be routed via an alternate path (if set up) until the
connection is marked good again.
The value is entered in [ms], milliseconds.
DLYLOLIM d Untere Grenze für die Verzögerung der VoIP
Payload-Verbindung zwischen HG 3500/HG 3575.
Bei Unterschreiten dieses Wertes wird eine vorher
als schlecht markierte Verbindung zwischen 2 HG
3500/75 wieder auf gut gesetzt.
Der Wert wird in [ms], Millisekunden eingegeben.
DLYLOLIM e Lower delay limit for VoIP payload connections
between HG 3500/HG 3575.
When delay falls below this value, a connection
between 2 HG 3500/75 that was previously marked
as bad is marked good again.
The value is entered in [ms], milliseconds.
LFRHILIM d Obere Grenze für die Paketverlustrate der VoIP
Payload-Verbindung zwischen 2 HG 3500/HG 3575.
Bei Überschreiten dieses Wertes wird die
Verbindung zwischen den 2 betroffenen HG 3500/75
als schlecht markiert. Künftige Verbindungen
zwischen diesen HG 3500/75 werden solange über
einen Alternativweg geführt (sofern einer eingerichtet
ist), bis die Verbindung wieder auf gut gesetzt wird.
Der Wert gibt das Verhältnis von verlorenen zu
gesendeten Paketen in Prozent an.
LFRHILIM e Upper limit for the fraction of lost packets on VoIP
payload connections between 2 HG 3500/HG 3575.
When the fraction of lost packets exceeds this value,
the connection between the 2 involved HG 3500/75
is marked as bad. Future connections between these
HG 3500/75 will be routed via an alternate path (if set
up) until the connection is marked good again.
The value is the ratio of lost to sent packages in
percent.
Table 4 AMO SIPCO parameters in CHANGE branch under TYPE=PLQUAL
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
LFRLOLIM d Untere Grenze für die Paketverlustrate der VoIP
Payload-Verbindung zwischen 2 HG 3500/HG 3575.
Bei Unterschreiten dieses Wertes wird eine vorher
als schlecht markierte Verbindung zwischen 2 HG
3500/75 wieder auf gut gesetzt.
Der Wert gibt das Verhältnis von verlorenen zu
gesendeten Paketen in Prozent an.
LFRLOLIM e Lower limit for the fraction of lost packets on VoIP
payload connections between 2 HG 3500/HG 3575.
When the fraction of lost packets falls below this
value, a connection between 2 HG 3500/75 that was
previously marked as bad is marked good again.
The value is the ratio of lost to sent packages in
percent.
Table 4 AMO SIPCO parameters in CHANGE branch under TYPE=PLQUAL
Bandwidth table (BANDW)

Change the system-wide bandwidth table with AMO SIPCO, CHANGE branch
under TYPE=BANDW.
Direct media connection (DMCDATA)

The parameter TYPE=DMCDATA specifies DMC specific data within CGW IPDA
pool.
In addition, the NWDMC parameter determines the codec type (G.711 or G.729)
to be used for DMC connections in network scenarios with TDM subscribers. This
information is provided for the Resource Manager only.
Data
Click Search, enable or disable the Direct Media Connection (DMC)
activated field on the System Data tab, select the code type, and Save.
CHANGE-SIPCO:TYPE=DMCDATA,DMCALLWD=N;NWDMC=G729;
The modified parameters are effective.

Language
SIPCO DMCERL d Direct Media Connection erlaubt.
Legt fest, ob Direct Media Connections auf allen
HG 3500 zu unterstützen sind, oder nicht.

TYPE=DMCDATA
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
DMCALLWD e Direct Media Connections allowed.
Specifies whether Direct Media Connections are to
be supported by all HG 3500 gateways - or not.
NWDMC d Codec-Typ für DMC-Verbindungen in Netzwerk-
Szenarien mit TDM-Teilnehmern.
G711 oder G729
NWDMC e Codec Type for DMC connections in networking
scenarios with TDM subscribers.
G711 or G729
TYPE=DMCDATA
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2 Access Point

When configuring an access point, a distinction must be made as to
• whether the access point involved is networked via routers in a network

segment other than the HiPath 4000 LAN segment (see Section 2.2.1,
“Configuring a “Networked” Access Point”),
or
• whether the access point is linked directly to the HiPath 4000 LAN
segment (see Section 2.2.2, “Configuring a “Direct Link“ Access Point”).
Figure 13 “Difference between “networked“ and “direct link“ access point”

illustrates the difference.
Access Point - networked Access Point - direct link

HG 3575 (NCUI) HG 3575 (NCUI)
SSH SSH
SNMP agent SNMP agent
APIPADDR
LSRTADDR
Interface
NCUI functionality NCUI functionality

Ethernet
for payload for payload

Interface
Ethernet
APIPADDR
NCUI functionality NCUI functionality
for signaling for signaling
Access point
NCUI Internal
Internal network segment
Router
Figure 13 Difference between “networked“ and “direct link“ access point
In all cases, an access point need not only be configured in the system. In order
to be able to address an access point, numerous data also has to be entered
locally at the access point during its initial installation (see Section 2.2.5, “Local
Configuration of an Access Point”). System administration should always be
performed first, followed by the local installation of the access point. The data to
be entered at the access point can be derived by Configuration Management or
directly from the data configured in the system using “HiPath 4000 Expert
Access“.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.1 Configuring a “Networked” Access Point
LSRTADDR APIPADDR
AP 99
HG
STMI-1 STMI-2
192.168.1.254 192.168.23.99 Peripheral

HG 3575 Boards
3500
Ra IP Rx AP 3700 IP
HG Router N et wor k Router
AP 98
3500 HG Peripheral
H iPath 4000 L AN Seg m ent
APRTADDR 3575 Boards

192.168.23.1
AP 3300 IP, AP 3500/3505
Peripheral
NETMASK
Boards
255.255.255.0
Ry
AP 43
HG Peripheral
Router 3575 Boards
ADP AP 3300 IP, AP 3500/3505

Atlantic LAN
AP 18
HG Peripheral
CC-A 3575 Boards
R1
Router P S T N N e t wo r k AP 3300 IP, AP 3500/3505
CC-B
AP 17
R10 HG Peripheral
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000
Figure 14 Configuring a “networked“ access point
ADD-UCSU: UNIT=AP, LTU=99,

LTPARTNO=Q2305-X35 SRCGRP=2,
FRMTYPE=AP 9837009, CONNTYPE=APNW,
LSRTADDR=192.168.1.254, APRTADDR=192.168.23.1,
LOCID=2, LOCATION=“BLN ROHRDAMM 85.
GEB. 30-222”,
PHONE=03038612345, FAX=03038654321,
PLCHECK=YES, BCHLCNT=40,
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
CONVLAW=NO, SIGMODE=HSRTCP;
ADD-APRT: TYPE=APNET, LTU=99,
APIPADDR=192.168.23.99, NETMASK=255.255.255.0;
Figure 14 “Configuring a “networked“ access point” shows the fundamental

information required for configuring a “networked“ access point
• The fact that the access point is linked via router with the HiPath 4000 LAN
segment: Link type APNW, i.e. “networked“.
• The LTU number of the access point, i.e. 99.
• The LTU part number specifies the HG 3575 used.
• The access point’s shelf type is derived from the type designation.
• The IP address of the access point: 192.168.23.99.
• The IP address for the TAP/Service PC link at the access point:

192.168.23.199.
• The IP address of the router (port), via which AP99 accesses the HiPath 4000
LAN segment: 192.168.23.1.
• The netmask in the segment of the AP99: 255.255.255.0.
• The IP address of the router (port) at the HiPath 4000 LAN segment, via
which the AP99 can be accessed by the central components in the HiPath
4000 LAN segment, i.e. in this case: 192.168.1.254.
• By limiting the number of B-channels, the bandwidth available to AP99 is

indirectly reduced in the configuration example. This mechanism works
independently of the bandwidth limitation performed by the Resource
Manager in the “Large Enterprise Gatekeeper” Feature. For further
information, please refer to Chapter 3, “Load Calculation”.
• Should Payload Quality Handling be activated? For details see Section 2.9,
“Payload Survivability”.
• The Source Group Index is explained in detail in Section 2.8, “Source

Dependent Routing”.
Additional data is explained in more detail with the corresponding AMO

parameters.
Generation
An access point is configured with three AMOs (UCSU, APRT, STMIB) and
activated with USSU.
UCSU
With the AMO UCSU, the access point is configured as a new shelf in the system
and its reachability via routers is ensured.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Point
Click New and enter the LTU of the access point.
Enter the relevant data on the General and IP Interface (NW) (Connect
Type=APNW) tab and Save.
ADD-UCSU:UNIT=AP,LTU=99,LTPARTNO=Q2305-X35,SRCGRP=2,
FRMTYPE=AP37009,CONNTYPE=APNW,LSRTADDR=192.168.1.254,
APRTADDR=192.168.23.1,LOCID=2,LOCATION=“BLN ROHRDAMM
85. GEB. 30-222”,PHONE=03038612345,FAX=03038654321,
PLCHECK=YES,BCHLCNT=40,CONVLAW=NO;
IMPORTANT: The parameters FRMTYPE and CONNTYPE cannot be changed

after the ADD!
IMPORTANT: Prior to ADD-UCSU, use ping to check that the IP addresses given
to you by the administrator are reachable.
LSRTADDR and APRTADDR must respond.

Language
UCSU LTSACHNR d Sachnummer der LTU-Baugruppe, hier die
Sachnummer der verwendeten NCUI2+/NCUI4.
LTPARTNO e Part Number of the LTU Board, here part number of
the NCUI2+/NCUI4 used.
SRCGRP d Source Group Index
Zuordnung des Access Points in eine Source
Group für “Source Dependent Routing”.
(Wegesuche in Abhängigkeit vom Rufenden)
Dieser Parameter ist wichtig für Source Dependent
Routing und Payload Survivability und wird dort
näher beschrieben.
SRCGRP e Source Group Index
Assignment of the Access Point to a Source Group
for “Source Dependent Routing”.
This parameter is relevant for Source Dependent
Routing and Payload Survivability and will be
described in more detail there.
FRAMETYP d Typ des LTU-Rahmens (Shelf Typ)
AP-Typ FRAMETYP
AP 3300 IP L80XF
AP 3500 IP INCH19
AP 3700 IP AP37009
Table 6 APNW: AMO UCSU parameters in ADD branch under TYPE=AP
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
FRMTYPE e Type of the LTU Frame (Shelf Type)
AP-Type FRAMETYPE
AP 3300 IP L80XF
AP 3500 IP INCH19
AP 3700 IP AP37009
VERBART d Art der Verbindung zwischen Access Point und
Zentrale Für IPDA kommen nur die Werte APDL
und APNW in Frage.
APNW - Access Point via Network: Access Point
und Zentrale werden in unterschiedlichen IP-
Netzen betrieben, welche über Router miteinander
verbunden sind.
CONNTYPE e Type of the Connection between Access Point and
the Central Switch
Only the values APDL and APNW are possible for
IPDA.
APNW - Access Point via Network: Access Point
and central switch are located in different IP-
Networks interconnected by routers.
LSRTADR d Adresse des Routers im HiPath 4000 LAN
Segment
VERBART=APNW:
IP Adresse des Routers (Ports) im HiPath 4000
LAN Segment, über den der Access Point / das
Netz, in dem sich der Access Point befindet,
erreichbar ist.
LSRTADDR e Address of the Router in the HiPath 4000 LAN
Segment
CONNTYPE=APNW:
IP address of the router (port) in the HiPath 4000
LAN Segment, via which the Access Point / the
network, where the Access Point is located, is
reachable.
APRTADR d Adresse des Routers im Netzwerk des Access
Points
IP Adresse des Routers (Ports) im Netz, in dem
sich der Access Point befindet, über den der
Access Point Adressen außerhalb dieses Netzes
erreicht.
VERBART=APNW:
Über diesen Router muss der Access Point CC-A,
CC-B, ADP und die HG 3500 Baugruppen im
HiPath 4000 LAN Segment erreichen sowie alle
anderen Access Points *).
*)Ausnahmen für Sonderrouten sind möglich und

werden im Routing Table Zweig des AMO APRT
eingerichtet.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
APRTADDR e Address of the Router in the Access Point’s
Network
IP address of the router (port) in the network where
the Access Point is located, via which the Access
Point reaches addresses outside of this network.
CONNTYPE=APNW:
Via this router the Access Point must be able to
reach CC-A, CC-B, ADP and the HG 3500 boards
in the HiPath 4000 LAN Segment as well as all
other Access Points*).
*) Exceptions for special routes are possible. They

are administered in the routing table branch of
AMO APRT.
STANDOID d Standort Identifikation
Schlüsselzahl zur Identifikation des Standorts
eines Access Points, der unterschiedlich zum
Standort der Zentralanlage sein kann. Der
Parameter wird benötigt, um den vertrieblichen
Bestand (PARK-Daten) der Anlagenteile
standortabhängig zu pflegen. Der Wert wird vom
Konfigurator-Tool vergeben und muss so
übernommen werden. Gegebenenfalls ist der Wert
vom Systemplaner zu erfragen. Ist kein Tool-
generierter Wert verfügbar, z.B. bei Teststellungen,
soll der Wert 999 verwendet werden, um dies
auszudrücken. Bei Erweiterungen an einem
Standort (zusätzlicher Access Point) kann der Wert
des bereits existierenden Access Points
übernommen werden. Systemkomponenten in
einem anderen Raum, Stockwerk, oder Gebäude
werden unter einer anderen Standort-Identifikation
geführt!
LOCID e Location Identification
Key number for identification of the location of an
Access Point, which can differ from the location of
the central switch. This parameter is necessary to
maintain the sales database for the parts of the
system, based on locations. The value is
determined by the Configurator tool and must be
taken over unchanged. If necessary, ask the
system planner for the value. If no tool-generated
value is available, e.g. for test and demo
configurations, the value 999 shall be used to
express this. For expansions at a certain location
(additional Access Point), the value of the already
exisiting Access Point can be taken. System
components in another room, floor or building are
listed under a different location ID.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
STANDORT d Angabe darüber, wo der Access Point zu finden ist.
z.B. Firma, Ort, Straße, Gebäude, Stockwerk,
Raumnummer, ...
Maximal 48 Zeichen können eingegeben werden.
LOCATION e Info, where to find the Access Point
E.g. Company, city, street, building, floor, room
number, ...
A maximum of 48 characters is allowed.
TEL d Telefonnummer am Standort des Access Points
Nächstgelegenes Telefon, über das ein Techniker
vor Ort am Access Point erreicht werden kann.
PHONE e Phone number at the Access Point
The nearest phone, where a service engineer can
be reached at the Access Point.
FAX d Faxnummer am Standort des Access Points
Nächstgelegenes Faxgerät, über das ein Techniker
FAX e Fax number at the Access Point
The nearest fax, where a service engineer can be
reached at the Access Point.
PLCHECK d Payload Quality Check
Gibt an, ob für diesen Access Point auf schlechte
Payload Qualität reagiert werden soll (durch
Sperren der Verkehrsbeziehung bzw. Weg über
Payload Survivability) oder nicht. 
-> Section 2.9, “Payload Survivability”
PLCHECK e Payload Quality Check
Defines whether this Access Point shall react on
bad Payload Quality (by blocking of the relation or
routing via Payload Survivability Path) or not.
ANZBKAN d Anzahl B-Kanäle
Gibt an, wieviele B-Kanäle an der Schnittstelle
zwischen Access Point und LAN gleichzeitig
genutzt werden dürfen. Auf diese Weise lässt sich
die maximale Bandbreite, die der Access Point im
LAN benötigt, grob begrenzen.
siehe Chapter 3, “Load Calculation”
BCHLCNT e B Channel Count
Defines how many B channels may be used
concurrently at the interface between Access Point
and LAN. By this the maximum bandwidth needed
by an Access Point can be limited coarsely.
see Chapter 3, “Load Calculation”
KONVLAW d Konvertierung von A-Law zu µ-Law bzw. µ-Law
nach A-Law auf der HG 3575 Baugruppe.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
CONVLAW e Conversion from A-law to µ-law or µ-law to A-law
on the HG 3575 board.
APRT
With the AMO APRT, the access point is assigned its own IP address.
Point
Enter IP addresses on the IP Interface (NW) tab and Save.
ADD-APRT:TYPE=APNET,LTU=99,APIPADDR=192.168.23.99,
NETMASK=255.255.255.0;
IMPORTANT: Prior to ADD-APRT, use ping to check that the IP addresses given
APIPADDR must not respond, as this would indicate that the corresponding
address had already been assigned.
APIPADDR must be set differently for every access point. The AMO does not
verify if this rule is observed.

Language
APRT APIPADR d Eigene IP-Adresse des Access Points
VERBART*)=APNW:
IP-Adresse des Access Points an dessen Ethernet-
Port.
APIPADR muss für jede Baugruppe unterschiedlich
sein. Der AMO prüft nicht die Einhaltung dieser
Regel.
*) AMO UCSU, ART=AP: siehe Parameter
VERBART in Table 6 “APNW: AMO UCSU
parameters in ADD branch under TYPE=AP”
APIPADDR e Own IP Address of the Access Point
CONNTYPE*)=APNW:
IP address of the Access Point’s ethernet port.
APIPADDR must be different for every board. The
AMO does not check compliance with this rule.
*) AMO UCSU, ART=AP: see see parameter
CONNTYPE in Table 6 “APNW: AMO UCSU
NETMASK d Netzmaske des Netzes, dem APIPADR angehört
Table 7 APNW: AMO APRT parameters in ADD branch under

TYPE=APNET
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
NETMASK e Netmask of the network which APIPADDR is part of
Table the
With 7 AMO APRT,
APNW: AMO APRT
additional parameters
functions in ADD point
of an access branch under
can be configured.
TYPE=APNET
• Signaling survivability
• Payload survivability - alternative routes -> Section 2.9, “Payload

Survivability”
• Additional routes in the IP network which cannot/should not be accessible via

the default router in the network of the access point or in the HiPath 4000 LAN
segment -> Section 2.5, “Special Routes”
STMIB
Nothing special has to be configured with STMIB. The CHANGE branches allow
a multitude of parameters to be set. Details are described in Section 2.2.3,
“Changing Access Point Parameters with the AMO STMIB”.
USSU
In order to actually put the access point into operation after the configuration
process, it has to be activated.
Data
Click Execute on the Action pull-down menu
and set the mode of action Configure AP, confirm with OK.
EXEC-USSU:MODE=CONFAP, LTU=xx;
From this moment on, the HiPath 4000 CC attempts to reach the access point
and, as soon it achieves this, to start it.
IMPORTANT: Prior to EXEC-USSU:CONFAP, the configuration must be updated

on the system hard disk, Otherwise, the data on the system would conflict with
the data on the HG 3575 when the system is reloaded and could only be synchro-
nized again with EXEC-USSU:UPDATAP,LTU number,UL.
In order to be able to reach the access point from the CC upon initial installation,
various data has to be entered locally at the access point (see Section 2.2.5,
“Local Configuration of an Access Point”).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.2 Configuring a “Direct Link“ Access Point
APRTADDR
AP 99
HG
STMI-1 STMI-2
192.168.1.254 Peripheral
HG 3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
AP 98
3500 I P N et wo r k HG Peripheral
HiPath 4000 L AN Se gment
3575 Boards
AP 3300 IP, AP 3500/3505

Peripheral
Boards
Ry
AP 43
HG Peripheral
Router 3575 Boards
ADP NETMASK AP 3300 IP, AP 3500/3505

Atlantic LAN
255.255.255.252
AP 18
HG Peripheral
CC-A APIPADDR 3575 Boards
R1
192.168.200.5 AP 3300 IP, AP 3500/3505
Router
PS T N N et wo r k
CC-B LSRTADDR
AP 17
R10 HG Peripheral
192.168.1.17 3575 Boards
Router
AP 3500 IP
CSTA
Assistant
HiPath
4000
Figure 15 Configuring a “Direct Link“ access point
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
TELNET server
Interface
FTP server
SNMP agent
Payload (RTP/RTCP)
Signalling
Service PC
H G 3 57 5
LSRTADDR NETMASK APIPADDR TAIPADR

192.168.1.17 255.255.255.252 192.168.200.5 192.168.200.6
Figure 16 Internal address assignment of a “direct link“ access point

LTPARTNO=Q2302-X10 SRCGRP=1,
FRMTYPE=INCH19, CONNTYPE=APDL,
LOCID=1, LOCATION=“MCH
MACHTLFINGERSTR.1 GEB.
7202-111”,
PHONE=08972223456, FAX=08972265432,
CONVLAW=NO;
In the case of a “direct link“ access point, the Ethernet port of the access point is
connected directly to the HiPath 4000 LAN segment and can be reached from
CC-A and CC-B without a router.
However, the signaling survivability feature requires the re-routing of a link in the
event of a fault (from LAN to modem). In order for this to function, the access point
may not be “logically“ present in the HiPath 4000 LAN segment. In this case, a
router is activated within the access point which forwards the packets from the
HiPath 4000 LAN to the “logical“, internal address of the access point.
To this end, the access point contains a “logical“ IP network in which only itself
and possibly the TAP/Service PC connection have an address. In order to save
addresses, the netmask 255.255.255.252 can be used for this address.
Even these mini-networks and their addresses must be coordinated with the
customer’s network administrator and, obviously, may not overlap.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Figure 15 “Configuring a “Direct Link“ access point” shows the following

fundamental information required for configuring a direct link access point:
• The fact that the access point is linked with the HiPath 4000 LAN segment:
Link type APDL, i.e. “direct link“.
• The LTU number of the access point, i.e. 17.
• The LTU part number specifies the HG 3575 used.
• The access point’s shelf type is derived from the type designation.
• The internal IP address of the access point: 192.168.200.5.
• The IP address for the TAP/Service PC link at the access point:

192.168.200.6.
• The IP address of the own Ethernet port via which the AP17 accesses the
HiPath 4000 LAN segment: 192.168.1.17.
• The netmask in the internal segment of the AP17: 255.255.255.252.
• The IP address of the router (port) at the HiPath 4000 LAN segment, via
which the AP17 can reach access points which cannot be accessed directly
at the HiPath 4000 LAN segment (that is “networked“ APs), in this case router
Ra: 192.168.1.254.
This router is omitted if there are no networked APs in the entire configuration
or if this is an isolated demo installation. The default router must be
configured with the zero address 0.0.0.0.
• By limiting the number of B-channels, the bandwidth available to AP99 is

indirectly reduced in the configuration example. This mechanism works
independently of the bandwidth limitation performed by the Resource
Manager in the “Large Enterprise Gatekeeper” Feature. For further
information, please refer to Chapter 3, “Load Calculation”.
• Should Payload Quality Handling be activated? For details see Section 2.9,
“Payload Survivability”
• The Source Group Index is explained in detail in Section 2.8, “Source

Dependent Routing”.
Additional data is explained in more detail with the corresponding AMO

parameters.
Generation
An access point is configured with three AMOs (UCSU, APRT, STMIB) and
activated with USSU.
UCSU
With the AMO UCSU, the access point is configured as a new shelf in the system
and its reachability via routers is ensured.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Point
Click New and enter the LTU of the access point.
Enter the relevant data on the General and IP Interface (DL) (Connect
Type=APDL) tab and Save.
ADD-UCSU:UNIT=AP,LTU=17,LTPARTNO=Q2302-
X10,SRCGRP=1,FRMTYPE=INCH19,CONNTYPE=APDL,LSRTADDR=19
2.168.1.17,APRTADDR=192.168.1.254,LOCID=1,LOCATION=“M
CH MACHTLFINGERSTR.1 GEB. 7202-
111”,PHONE=08972223456,FAX=08972265432,PLCHECK=YES,BC
HLCNT=20,CONVLAW=NO;
The parameters FRMTYPE and CONNTYPE cannot be changed after the ADD!
IMPORTANT: Prior to ADD-UCSU, use ping to check that the IP addresses given
APRTADDR must respond.
LSRTADDR must not respond, as this would indicate that the corresponding
address had already been assigned.
LSRTADDR must be set differently for every “direct link“ access point. The AMO
does not verify if this rule is observed.

Language
UCSU LTSACHNR d Sachnummer der LTU-Baugruppe, hier die
Sachnummer der verwendeten NCUI2+/NCUI4.
LTPARTNO e Part Number of the LTU Board, here part number
of the NCUI2+/NCUI4 used.
Group für “Source Dependent Routing”.
(Wegesuche in Abhängigkeit vom Rufenden)
Dieser Parameter ist wichtig für Source
Dependent Routing und Payload Survivability und
wird dort näher beschrieben.
Assignment of the Access Point to a Source
Group for “Source Dependent Routing”.
This parameter is relevant for Source Dependent
Routing and Payload Survivability and will be
described in more detail there.
Table 8 APNW: AMO UCSU parameters in ADD branch under ART=AP
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
FRAMETYP d Typ des LTU-Rahmens (Shelf Typ)
AP-Typ FRAMETYP
AP 3300 IP L80XF
AP 3500 IP INCH19
AP 3700 IP AP37009
FRMTYPE e Type of the LTU Frame (Shelf Type)
AP-Type FRAMETYPE
AP 3300 IP L80XF
AP 3500 IP INCH19
AP 3700 IP AP37009
VERBART d Art der Verbindung zwischen Access Point und
Zentrale Für IPDA kommen nur die Werte APDL
und APNW in Frage.
APDL - Access Point Direct Link: - Access Point ist
direkt am HiPath 4000 LAN Segment
angeschlossen, d.h. im selben IP-Netz.
CONNTYPE e Type of the Connection between Access Point and
the Central Switch
Only the values APDL and APNW are possible for
IPDA.
APDL - Access Point Direct Link: - Access Point is
connected directly to the HiPath 4000 LAN
Segment, i.e. in the same IP network.
LSRTADR d Adresse des Routers im HiPath 4000 LAN
Segment
VERBART=APDL:
Dies ist die IP-Adresse am Ethernet-Port des
Access Points, über den er mit dem HiPath 4000
LAN Segment verbunden ist. Bei APDL enthält der
Access Point einen lokalen Router der die IP-
Adresse des Access Points (in einem eigenen
Netzwerksegment) mit dem HiPath 4000 LAN
Segment verbindet. D.h. auch hier handelt es sich
um die Adresse eines (wenn auch unsichtbaren)
Routers.
Diese IP-Adresse muss zum HiPath 4000 LAN
Segment gehören (siehe NETADR im AMO
SIPCO).
LSRTADR muss für jede Baugruppe
unterschiedlich sein. Der AMO prüft nicht die
Einhaltung dieser Regel.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
LSRTADR e Address of the Router in the HiPath 4000 LAN
Segment
CONNTYPE=APDL:
This is the IP address of the Access Point’s
ethernet port connected to the HiPath 4000 LAN
Segment. With APDL the AP contains a local
router that connects the own IP address of the
Access Point (in its own network segment) to the
HiPath 4000 LAN Segment. It’s a router’s address,
even with the router invisible.
This IP address must belong to the HiPath 4000
LAN Segment (see NETADDR in AMO SIPCO)
LSRTADDR must be different for every board. The
APRTADR d Adresse des Routers im Netzwerk des Access
Points
IP Adresse des Routers (Ports) im Netz, in dem
sich der Access Point befindet, über den der
Access Point Adressen außerhalb dieses Netzes
erreicht.
VERBART=APDL:
Über diesen Router muss der direkt am HiPath
4000 LAN Segment angeschlossene Access
Point alle Access Points erreichen, die sich in
anderen Netzen befinden. Meist ist dies der
Default-Router des HiPath 4000 LAN Segments,
welcher mit dem Parameter DEFRT im AMO
SIPCO eingerichtet wird*).
Sind in der gesamten Konfiguration keine
“networked“ APs enthalten, oder ist dies eine
isolierte Demo-Installation, so enfällt dieser
Router. Geben Sie dazu hier die Null-Adresse
0.0.0.0 an.
*)Ausnahmen für Sonderrouten sind möglich und

werden im Routing Table Zweig des AMO APRT
eingerichtet.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
APRTADDR e Address of the Router in the Access Point’s
Network
IP address of the router (port) in the network
where the Access Point is located, via which the
Access Point reaches addresses outside of this
network.
CONNTYPE=APDL:
Via this router an Access Point directly connected
to the HiPath 4000 LAN Segment must be able to
reach all Access Points that are located in different
networks. Usually this is the default router of the
HiPath 4000 LAN Segment, administered in
parameter DEFRT with AMO SIPCO*).
If there are no “networked“ APs in the whole
configuration or if this is a stand-alone demo
installation, this router is not needed. Give the
address 0.0.0.0 for this purpose.
*) Exceptions for special routes are possible. They

are administered in the routing table branch of
AMO APRT.
STANDOID d Standort Identifikation
Schlüsselzahl zur Identifikation des Standorts
eines Access Points, der unterschiedlich zum
Standort der Zentralanlage sein kann. Der
Parameter wird benötigt, um den vertrieblichen
Bestand (PARK-Daten) der Anlagenteile
standortabhängig zu pflegen. Der Wert wird vom
Konfigurator-Tool vergeben und muss so
übernommen werden. Gegebenenfalls ist der
Wert vom Systemplaner zu erfragen. Ist kein Tool-
generierter Wert verfügbar, z.B. bei
Teststellungen, soll der Wert 999 verwendet
werden, um dies auszudrücken. Bei
Erweiterungen an einem Standort (zusätzlicher
Access Point) kann der Wert des bereits
existierenden Access Points übernommen
werden. Systemkomponenten in einem anderen
Raum, Stockwerk, oder Gebäude werden unter
einer anderen Standort-Identifikation geführt!
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
LOCID e Location Identification
Key number for identification of the location of an
Access Point, which can differ from the location of
the central switch. This parameter is necessary to
maintain the sales database for the parts of the
system, based on locations. The value is
determined by the Configurator tool and must be
taken over unchanged. If necessary, ask the
system planner for the value. If no tool-generated
value is available, e.g. for test and demo
configurations, the value 999 shall be used to
express this. For expansions at a certain location
(additional Access Point), the value of the already
exisiting Access Point can be taken. System
components in another room, floor or building are
listed under a different location ID.
STANDORT d Angabe darüber, wo der Access Point zu finden
ist.
z.B. Firma, Ort, Straße, Gebäude, Stockwerk,
Raumnummer, ...
Maximal 48 Zeichen können eingegeben werden.
LOCATION e Info, where to find the Access Point
E.g. Company, city, street, building, floor, room
number, ...
A maximum of 48 characters is allowed.
TEL d Telefonnummer am Standort des Access Points
Nächstgelegenes Telefon, über das ein Techniker
PHONE e Phone number at the Access Point
The nearest phone, where a service engineer can
be reached at the Access Point.
FAX d Faxnummer am Standort des Access Points
Nächstgelegenes Faxgerät, über das ein
Techniker vor Ort am Access Point erreicht
werden kann.
FAX e Fax number at the Access Point
The nearest fax, where a service engineer can be
reached at the Access Point.
PLCHECK d Payload Quality Check
Gibt an, ob für diesen Access Point auf
schlechte Payload Qualität reagiert werden
soll (durch Sperren der Verkehrsbeziehung
bzw. Weg über Payload Survivability) oder
nicht.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
PLCHECK e Payload Quality Check
Defines whether this Access Point shall react on
bad Payload Quality (by blocking of the relation or
routing via Payload Survivability Path) or not.
ANZBKAN d Anzahl B-Kanäle
Gibt an, wieviele B-Kanäle an der Schnittstelle
zwischen Access Point und LAN gleichzeitig
genutzt werden dürfen. Auf diese Weise lässt sich
die maximale Bandbreite, die der Access Point im
LAN benötigt, grob begrenzen.
siehe Chapter 3, “Load Calculation”
BCHLCNT e B Channel Count
Defines how many B channels may be used
concurrently at the interface between Access
Point and LAN. By this the maximum bandwidth
needed by an Access Point can be limited
coarsely.
see Chapter 3, “Load Calculation”
KONVLAW d Konvertierung von A-Law zu µ-Law bzw. µ-Law
nach A-Law auf der HG 3575 Baugruppe.
CONVLAW e Conversion from A-law to µ-law or µ-law to A-law
on the HG 3575 board.
APRT
With the AMO APRT, the access point is assigned its own (internal) IP address.
Point
Enter IP addresses on the IP Interface (DL) tab and Save.
ADD-APRT:TYPE=APNET,LTU=17,APIPADDR=192.168.200.5,
NETMASK=255.255.255.252;
IMPORTANT: If you want to check the (internal) APIPADDR IP address after

startup using ping, you must configure the route to the AP internal network
segment on the computer from which the ping is dispatched.
=> Host=APRT:APIPADDR, Netmask=APRT:NETMASK,
Router=UCSU:LSRTADDR.

APIPADDR must be set differently for every access point. The AMO does not
verify if this rule is observed.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point

Language
APRT APIPADR d Eigene IP-Adresse des Access Points
VERBART*)=APDL:
IP-Adresse des Access Points in seinem eigenen
Netzwerksegment
- nicht die IP-Adresse the Ethernet-Ports, welche in
diesem Fall vom internen Router belegt wird.
APIPADR muss für jede Baugruppe unterschiedlich
Regel.
*) AMO UCSU, ART=AP: siehe Parameter
VERBART in Table 6 “APNW: AMO UCSU
APIPADDR e Own IP Address of the Access Point
CONNTYPE*)=APDL:
IP address of the Access Point in its own network
segment
- not the IP address of it’s ethernet port which is
assigned to the internal router in this case.
APIPADDR must be different for every board. The
*) AMO UCSU, UNIT=AP: see parameter
CONNTYPE in Table 6 “APNW: AMO UCSU
NETMASK d Netzmaske des Netzes, dem APIPADR angehört
NETMASK e Netmask of the network which APIPADDR is part of
Table 9 APDL: AMO APRT parameters in ADD branch under TYPE=APNET
With the AMO APRT, additional functions of an access point can be configured.
• Signaling survivability
• Payload survivability - alternative routes -> Section 2.9, “Payload

Survivability”
• Additional routes in the IP network which cannot/should not be accessible via

the default router in the network of the access point or in the HiPath 4000 LAN
segment -> Section 2.5, “Special Routes”
STMIB
Nothing special has to be configured with STMIB. The CHANGE branches allow
a multitude of parameters to be set. Details are described in Section 2.2.3,
“Changing Access Point Parameters with the AMO STMIB”.
USSU
In order to actually put the access point into operation after the configuration
process, it has to be activated.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Data
Click Execute on the Action pull-down menu
and set the mode of action Configure AP, confirm with OK.
EXEC-USSU:MODE=CONFAP,LTU=xx;
From this moment on, the HiPath 4000 CC attempts to reach the access point
and, as soon it achieves this, to start it.
IMPORTANT: Prior to EXEC-USSU:CONFAP, the configuration must be updated

on the system hard disk, Otherwise, the data on the system would conflict with
the data on the HG 3575 when the system is reloaded and could only be synchro-
nized again with EXEC-USSU:UPDATAP,LTU number,UL.
In order to be able to reach the access point from the CC upon initial installation,
various data has to be entered locally at the access point (see Section 2.2.5,
“Local Configuration of an Access Point”).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.3 Changing Access Point Parameters with the

AMO STMIB
Please refer to Chapter 12, “Gateway HG 3575 - Changing Parameters with AMO
STMIB” in the document “Gateways HG 3500 and HG 3575”.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.4 Deleting an Access Point

If an access point is to be removed from the configuration (in the example: AP
43), the following sequence must be complied with:
• If payload survivability is configured, it must first be checked whether the

access point to be deleted provides the trunk access for a source group. If it
does, a suitable replacement must be found.
• If payload survivability is configured and a source group becomes

superfluous when an access point is deleted, the LCR must be adapted and
the source group deleted if necessary.
Configuration Management --> System Data --> IPDA

--> IPDA - Payload Survivability
Click Search, select the access point and Delete.
DELETE-APRT:TYPE=ALTROUT,SRCGRP=3;
• Deletion of all peripheral modules configured within this access point

(presupposes that no subscribers are configured on that module, etc.)
• If signaling survivability is configured for this access point:

Delete the assignment of this access point to a survivability router

Access Point
Delete the desired router number on the General tab under Signaling
Survivability and Save.
DELETE-APRT:TYPE=SURV,CONF=AP,LTU=43;
• If special routes are configured:

(Section 2.5, “Special Routes”)
• Delete the corresponding entries in the routing tables of other access

points, if these entries lose their validity for additional access points.
In the example in Figure 21 “Special routes between access points”, the
route via Router Rz becomes superfluous if AP 43 is deleted. If, however,
AP 98 was deleted instead of AP 43, the route would have to remain in
place, as it is also valid for AP 99.
Configuration Management --> System Data --> IPDA --> HG3575

Additional Routing
Enter zero addresses (0.0.0.0) in the lines of the routing table that are
to be deleted and Save.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
DEL-APRT:TYPE=ROUTTBL,MTYPE=NCUI,LTU=99,INDEX=1;
Note: No distinction is made here between hardware types. NCUI
applies to NCUI2 and NCUI4.
• Deactivating the access point with USSU:

Access Point
DEACTIVATE-USSU:LTU=43;
• Deactivating the IP connection of the access point with USSU:

System Data
OK.
EXEC-USSU:MODE=DELAP,LTU=43;
• Deleting the access point (CM):

Access Point
Click Search and select the access point, then click Delete.
• Deleting the IP network configuration of the access point:
DELETE-APRT:TYPE=APNET,LTU=43;
• Deleting the access point with UCSU:
DELETE-UCSU:UNIT=AP,LTU=43;
IMPORTANT: If the removed access point was configured for AP Emergency

(i.e. it was assigned an emergency group), you must observe the following: 
The IP address of the removed access point can only be reused when this
change has been saved on all CC APs, in other words, when “cloning“ is
completed using HiPath 4000 Assistant > Backup & Restore.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.5 Local Configuration of an Access Point

If an access point has been configured in the HiPath 4000 switch, it cannot be put
into operation immediately. The central system cannot establish contact with the
access point until this has been configured with the essential IP addresses, etc.
“HiPath 4000 Expert Access“ application is available in order to perform this initial
access point configuration locally. To this end, the TAP/Service PC is connected
to the RS232/V.24 interface of the HG 3575 with the designation “Service“ and
the application started.
The terminal login must be used for login purposes. In the case of virgin modules,
this is "TRM", and no password is set. If the module has already been in operation
and the terminal login and password have been changed, these later values
apply.
If there is a duplex processor (CC-B) in the HiPath 4000 switch, the address must
always be specified. After all, it is not possible to predict whether CC-A or CC-B
will be playing the active role at this time. If there is no CC-B in the system, the IP
address for this processor is not needed.
The IP address of the TAP need only be specified if the administration function of
the HiPath 4000 switch is to be accessed from this access point.
If VLAN tagging is used in the Ethernet segment to which the access point should
be connected, a setting must be performed for it during initial startup.
If the access point was operated in a network with VLAN tagging and should now
run without VLAN tagging, this setting must also be changed locally.
If the access point is to be operated with fixed Ethernet interface settings for bit
rate and mode or if this fixed setting is to be removed (in the event of relocation
to another network), this setting too must be performed locally.
Of the parameters which are displayed and adjustable, only a certain number
actually have to be entered. All other parameters are loaded from the HiPath
4000 switch as soon as the central system can establish contact with the access
point;
IMPORTANT: Changing a parameter value locally does not result in a change of

the value in the system.
Absolutely all parameters configured locally at the access point are overwritten
by the values configured in the system upon loading the module from the HiPath
4000 switch.
When configuring the access point locally, a distinction is again also made
between “networked“ and “direct link“.
Networked access point

The following fields must be completed:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Parameter Note AMO - Zweig -

Parameter
IP address of the access May not be in the same network as APRT
point the IP address of the CC-A TYPE=APNET -
APIPADDR
Netmask in the network of The netmask must match the IP APRT
the access point address class of the access point. TYPE=APNET -
NETMASK
IP address of the default Must be in the same network as the UCSU
router in the network of the IP address of the access point UNIT=AP -
access point APRTADDR
IP address of the CC-A SIPCO
TYPE=LSNET -
CCAADDR
IP address of the CC-B Must be in the same network as the SIPCO
IP address of the CC-A TYPE=LSNET -
CCBADDR
Netmask of the HiPath 4000 The netmask must match the IP SIPCO
LAN segment address class of the CC-A. TYPE=LSNET -
NETMASK
VLAN tagging on/off STMIB:
MTYPE=NCUI2,
TYPE=IFDATA -
VLAN
VLAN ID STMIB:
MTYPE=NCUI2,
TYPE=IFDATA -
VLANID
Ethernet interface operating STMIB:
mode MTYPE=NCUI2,
TYPE=IFDATA -
BITRATE
Table 10 Basic initialization parameters for “networked“ access points
Direct link access point

Parameter Note AMO - Branch -

Parameter
IP address of the access point Must be in the same network as the UCSU
in the HiPath 4000 LAN IP address of the CC-A UNIT=AP -
segment LSRTADDR
HiPath 4000 LAN segment The netmask must match the IP SIPCO
Netmask address class of the CC-A. TYPE=LSNET -
NETMASK
Table 11 Basic initialization parameters for “direct link“ access point
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
Parameter Note AMO - Branch -

Parameter
IP address of the default Must be in the same network as the UCSU
router in the HiPath 4000 LAN IP address of the CC-A UNIT=AP -
segment APRTADDR
IP address of the CC-A SIPCO
TYPE=LSNET -
CCAADDR
IP address of the CC-B Must be in the same network as the SIPCO
IP address of the CC-A TYPE=LSNET -
CCBADDR
IP address of the access point May not be in the same network as APRT
in the internal AP network the IP address of the CC-A TYPE=APNET -
segment APIPADDR
Netmask of the internal AP The netmask must match the IP APRT
network segment address class of the access point in TYPE=APNET -
the internal AP network segment. NETMASK
VLAN tagging on/off STMIB:
MTYPE=NCUI2,
TYPE=IFDATA -
VLAN
VLAN ID STMIB:
MTYPE=NCUI2,
TYPE=IFDATA -
VLANID
Ethernet interface operating STMIB:
mode MTYPE=NCUI2,
TYPE=IFDATA -
BITRATE
Table 11 Basic initialization parameters for “direct link“ access point
Information on local configuration without the “HiPath 4000 Expert Access“
application can be found in Chapter 4, “Local Access Point Administration at CLI
via Terminal”.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.6 Reference Clock in Access Point

The HiPath 4000 central system has a highly precise clock generator which can
be synchronized from various sources. Possible sources include, for instance,
digital trunk circuits. The corresponding connection modules can then supply the
clock timing in the LTUs 1-15 and synchronize the central clock generator. The
AMO REFTA is responsible for configuring which circuits can be used as
reference clock suppliers and querying which supplier is currently active.
Access Points of the type AP 3300 IP, AP 3500 IP or AP 3700 IP are connected
in asynchronous fashion via the IP network. Thus, the central clock generator
cannot be synchronized from LTUs 17-99.
On account of this asynchronous connection, the access point itself is also unable
to be synchronized from the central clock generator. Therefore, the HG 3575
module of the access point is equipped with its own highly precise clock
generator.
The asynchronism of the clock generators in the HiPath 4000 central system and
in the various access points has no interfering effect on the communication
between these components. The jitter buffers required for voice transmission also
compensate smoothly for the slight slip between the clock generators.
However, if digital trunk or tie trunk circuits are operated in an access point, the
local clock generator must be synchronized with the network clock (“CO Clock“).
To this end, management of the reference clock has been extended with the AMO
REFTA. The basic principle is simple:
• Reference clock sources in LTUs 1-15 are used to synchronize the central
clock generator.
• Reference clock sources in LTUs 17-99 are used to synchronize the local
clock generators in the respective access point.
Thus, in a HiPath 4000 switch with 83 access points of the type AP 3300 IP or AP
3500 IP, the synchronization of 84 clock generators has to be managed. This
means that 84 active clock suppliers (central unit + 83 access points) may exist
in such a system.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.7 Loading new Loadware on a HG 3575

From HiPath 4000 V4 on a new load concept via HTTPS has been developped
for HG 3575 and HG 3500. Please refer to “Gateways HG 3500 and HG 3575“,
Chapter 7, “Load Concept for Gateway Boards”.
The loadware for a HG 3575 is very extensive. If, while the module is being
loaded, it is determined that the loadware in the flash memory of the
module does not match the loadware stored in the hard disk of the HiPath 4000
central system, the loadware is reloaded on the HG 3575.
The loadware is transferred via FTP-Push (load functionality via hhtps hasn’t
been used, i.e. loading via LW Update Manager), with the HG 3575 downloading
the loadware from the FTP server of the HiPath 4000 central processor (in the
RMX system).
The FTP server can only transfer loadware to up to five HG 3575 boards at a time.
If there are multiple HG 3575s in the system (up to 83 access points are possible),
the other modules wait their turn in case of a system reload. This takes quite a
long time and considerably slows down startup of the system.
IMPORTANT: With the feature “AP Multicast Loading” the downtime of a system
in case of a system update (system relaod with software/loadware version) will be
reduced. For details please refer to Section 2.2.8, “Updating Access Point
Loadware during an RMX Upgrade (New Fix Release/Minor Release)”.
It is therefore possible for a HG 3575 to download new loadware from the FTP
server in the background, which means while the system is running. Therefore
the loadware update manager of the HiPath 4000 should be used (see „Gateways
HG 3500 and HG 3575“, Section 7.5, “Updating Loadware with "LW Update
Manager"”).
Alternative the loadware can be transferred via FTP-Push while the system is
running, without executing it immediately. Actions of this type should be
performed at off-peak times, as the loadware transfer reduces the bandwidth for
signaling messages. The load operation can also be performed with signaling
survivability. The effect on the available bandwidth is particularly critical in this
case.
Point
Background Loading of NCUI LW Files, select LW under Files to be
Loaded and confirm with OK.
EXEC-USSU:MODE=NCUILOAD,LTU=xx,FILES=LW;
If the LTU number is not specified, all HG 3575s that are ready (READY) at
this time are loaded.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
SIU files can also be loaded in this way.
FILE=
SIUTONES TONES
SIURECV SIU-RECEIVERS
SIUANN SIU-ANNOUNCEMENTS
SIUMOH SIU -MUSIC ON HOLD
SIUTDS SIU -TDS
LW LW file -- NCUI
ALLSIU All possible SIUs
ALL All loadable files
To apply the loadware while the system is active, the following actions are
required:
Point
Once the system has confirmed deactivation of the AP, reactivate it with
Activate.
DEACTIVATE-USSU:LTG=1,LTU=xx;
ACTIVATE-USSU:UNIT=LTG,LTG=1,LTU=xx;
IMPORTANT: Connections are cleared down without further warning!
Changing the music on hold (MOH) in the system (AMO ZAND:MELODY=X)
When changing the MELODY setting, the following command sequence must be
executed (for each AP) so that the changes become effective immediately:
Configuration Management --> System Data --> IPDA

--> IPDA Access Point
Once the system has confirmed deactivation of the AP,
reactivate it with Activate.
DEACTIVATE-USSU:LTG=1,LTU=xx;
ACTIVATE-USSU:UNIT=LTG,LTG=1,LTU=xx;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.8 Updating Access Point Loadware during an

RMX Upgrade (New Fix Release/Minor Release)
The feature "AP multicast loading" lets you perform simultaneous loading
operations for multiple access points. Originally, simultaneous loading operations
were only possible for access points containing boards that already featured the
latest loadware. With “AP multicast loading” it is also possible if the boards need
new loadware.
Procedure
1. Use the traditional FTP solution to transfer the new loadware for the HG 3575
to the access point (up to five access points per run). See also Section 2.2.7,
“Loading new Loadware on a HG 3575”.
Once the new loadware has been successfully transferred and activated, the
TCP/IP connection is re-established between the host system (HSR) and the
access point.
To transfer the loadware downloaded in the background to the NCUI a warm
boot is initiated and executed.
The restart (warm boot) with the new loadware is followed by a golden
loadware check. If this golden loadware check fails, the NCUI restarts with the
old loadware and the new loadware (HD) is retransmitted.
IMPORTANT: This step is skipped if there is no new loadware available for

the HG 3575.
2. The loadware transfer for the peripheral boards starts.
3. The access points are entered in the load list once the loadware has been
transferred.
4. The first access point in the load list is put into full operation immediately
(takes approx. 15 minutes). While this access point is being put into
operation, other access points that have already completed the loadware
transfer/activation are entered in the load list.
5. As soon as the first access point has gone into operation, all access points
that have been entered in the load list in the meantime are simultaneously
loaded and put into operation.
IMPORTANT: In the past, the APs in the load list were processed or put into
operation in sequential order.
6. While these access points are being put into operation, other access points
that have completed loadware transfer/activation are entered in the load list.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
7. As soon as the access points have gone into operation, all access points
grouped together on the load list are put into operation simultaneously.
8. These procedures are repeated until all access points have been upgraded.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.9 Information on Exchanging HG 3575 Boards

The following must be observed when exchanging a HG 3575 board in a system:
• The HG 3575 board must not be powered on or plugged in.
• The new board must be configured with the same basic configuration as the
old board (IP addresses, etc.). 
To do this, the configuration of the old board can be read out using “HiPath
4000 Expert Access“ and stored on a file with which the new board can be
configured.
If this is no longer possible with the old board, the data must be taken from
the system configuration.
• Every HG 3575 board has an individual Ethernet MAC address. The MAC
address which is visible from the network changes when boards are changed.
IMPORTANT: Please inform the network carrier of the change. The network
provider needs the MAC addresses to find devices involved in IP address
conflicts.

The board’s MAC address can be found on the sticker on the solder side of the
printed circuit board.
• The following AMO action must be performed once the module has been
booted:
Unconditional loading can only be initiated in expert mode.

Expert Mode --> HiPath 4000 Expert Access --> Open ...<IP> with
AMO (see AMO command)
EXEC-USSU:UPDATAP,LTU=<number>,UL;
This ensures that the entire system configuration data is written to the
module. The access point is thus restarted and is booted using the latest data. 
This is necessary as the system does not always detect that the boardwas
exchanged.
This process is also required if the same board was removed from the
system, reconfigured locally and put back in the same position in the system.
For more information on exchanging HG 3575 boards refer to document

„Gateways HG 3500 and HG 3575“, Section 4.2.2, “Exchanging Boards”).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.10 Information on the 19“ AP 3500 IP Access Point

Figure 17 “AP 3500 IP - front view” shows the front view of a AP 3500 IP. The shelf
can be mounted in a 19“ rack using additional angle brackets and has a height of
3HE.
There is space on the left for 4 modules and the topmost slot is allocated to the
HG 3575 (NCUI2/4). Peripheral modules of the HiPath 4000 can be inserted into
the other slots. These modules are covered by a metal panel that is inserted
separately. In the figure, this panel has been removed from the bottom slot.
At the rear, either the usual main distribution cables can be attached or plug-in
patch panels can be used to connect the devices directly using Western plugs.
In addition to the modules, the rack also contains 2 power supply modules on top
of one another. The AP 3500 IP can be operated using a power supply module.
A second may also be operated as a redundant unit.
A ventilator module is located at the right-hand side. Because the modules are in
a horizontal position, the system has to be forced ventilated.
IMPORTANT: The ventilation openings on the left and right-hand side of the
housing must not be obstructed. The operating position of the equipment is
horizontal.
Figure 17 AP 3500 IP - front view
The AP 3500 IP can be extended by four slots using a AP 3505 IP with a similar
structure (no HG 3575 in the AP 3505).
Special features
• The AP 3500 IP represents the left and the optional AP 3505 IP represents
the right half of a conventional shelf.
• The slots are counted from bottom up and are numbered 1,2,3 and 4 in the
AP 3500 IP 
(4 is HG 3575), and 5,6,7 and 8 in the optional AP 3505 IP.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
• Boards with front connectors can only be used if they are fitted with a suitable
metal panel (for example, STMI2, DIUN2 starting with status -X-7, SLC24
starting with status -X200-9, PBXXX starting with status -X-F3, ...)
• SIVAPAC modules with adapters are not supported, because they do not fit
under the shielding cover. As an exception, a number of these boards are
fitted with a new plastic panel C39228-A402-C21. (TMEW2,
SLMA,TMDID,TMEMUS).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Access Point
2.2.11 Information on the 19“ AP 3700 IP Access Point

The frame of an AP 3700 IP can be installed in 19“ cabinets. For this, it must be
set on sliding rails/mounting rails installed in the cabinet and terminated at the
cabinet uprights by means of the 19“ mounting bracket supplied.
AP 3700 IP required a height of 11 HE (10 HE + 1 HE play).
IMPORTANT: AP 3700 IP is not forced ventilated and consequently, does not

feature a fan. 
For installation, please pay particular attention to requirements in terms of air
supply and minimum air volume specified in the installation instructions.
The left half of the shelf can accommodate five peripheral boards (slot 1 to 5). HG
3575-2 (NCUI2) is supported on the central slot (slot 6). The correct shelf half
accommodates four peripheral boards (slot 7 to 10).
If the peripheral boards are not already equipped with a suitable metal panel (for
example, STMI2, slot 4 and 9), they are covered by a metal panel that is inserted
separately. (on slot 1 and 2 in the diagram). Unused slots must be covered by a
metal panel and guarantee the necessary level of shielding.
Boards with front connectors can only be used if they are fitted with a suitable
metal panel (for example, STMI2, DIUN2 starting with status -X-7, SLC24 starting
with status -X200-9, PBXXX starting with status -X-F3, ...)
SIVAPAC modules with adapters are not supported, because they do not fit under
the shielding cover. As an exception, a number of these boards are fitted with a
new plastic panel C39228-A402-C21. (TMEW2, SLMA,TMDID,TMEMUS).
The project planning guideline’s instructions on the installation of peripheral

boards should therefore be followed precisely.
At the rear, either the usual main distribution cables can be attached or plug-in
patch panels can be used to connect the devices directly using Western plugs.
Up to three power supply modules can be connected side by side under the
board. Two modules are sufficient for supplying the maximum configuration. A
third module may also be connected as a redundant unit.
The power supply modules can be connected to the 115/230 V alternating current
or 48 V direct current. The three modules are fed over a shared connected at the
rear of the housing.
The right part of the AP 3700 IP can accommodate a survivability unit, a cPCI
cassette with a standalone emergency control unit.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
HG 3500 as HG3570 in the HiPath 4000 System
2.3 HG 3500 as HG3570 in the HiPath 4000 System

For mor information on HG 3500 gateway please refer to „Gateways HG 3500
and HG 3575“.
The common gateway HG 3500 - added as HG3570 - establishes the payload

connections between the central HiPath 4000 system and the access points
distributed within the framework of the IP distributed architecture.
• HG 3500 gateways, configured as HG 3570, may only be used in the

peripheral shelves (LTU 1-15) of the central system.
• The time slots required by the HG 3570 gateways in a half shelf must be
nonblocking. The maximum number of B channels supported by the board
hardware can be reduced using the BCHLCNT command in the AMO BFDAT.
• Every shelf in which a HG 3570 is installed must be equipped with an LTUCX

module.
• Up to 83 HG 3570 gateways can be used in a HiPath 4000 system. The

payload connections between the central HiPath 4000 system and the access
points are distributed evenly across all HG 3500s.
• There is no assignment of payload connections from HG 3575 to HG 3500.

The number of HG 3500s in the system is based on the traffic volume, not on
the number of access points. If one HG 3500 fails, it is not assigned any new
calls. The other available HG 3500s take on the payload.
IPADDR
AP 99
HG
STMI-1 STMI-2
HG 192.168.1.11 Peripheral
3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
AP 98
3500 HG Peripheral
3575 Boards
I P N et wor k
AP 3300 IP, AP 3500/3505
Peripheral
Boards
Ry
AP 43
HG Peripheral
Router 3575 Boards
ADP AP 3300 IP, AP 3500/3505

Atlantic LAN
CC-A
AP 18
HG Peripheral
3575 Boards
R1
CC-B
Router PSTN Netwo r k AP 3300 IP, AP 3500/3505
AP 17
CSTA R10 HG Peripheral

3575 Boards
Router
AP 3300 IP, AP 3500/3505
Assis
tant
HiPath
4000
Figure 18 Configuring a HG 3500 for IPDA
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

BRDBCHL=BCHL60&BCHL120
;
FUNCTION=HG3570, BCHLCNT=40;
ANSW=YES;
ADD-BCSU: MTYPE=IPGW, LTU=5,
SLOT=91, PARTNO=Q2316-X,
FCTID=1, FCTBLK=1,
IPADR=192.168.1.11, BKAN3570=40;
CHNAGE-BCSU: TYPE=HWYBDL, LTU=5,
HWYBDL=A;
Generation
A HG 3500 module with FUNCTION=HG3570 is configured with 3 AMOs: AMO
BFDAT, AMO BCSU and AMO CGWB.
However, AMO CGWB is only needed if additional routes in the IP network are
required in addition to the default router in the HiPath 4000 LAN segment. Please
refer to Section 2.5, “Special Routes”.
BFDAT
Configuration of the functional blocks for common gateway boards for IPDA.
Configuration Management --> System Data --> Board --> CGW

Function Block
ADD-BFDAT:FCTBLK=1,FUNCTION=HG3570,BRDBCHL=NCHL&BCHL;
CHA-
BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3570,BCHLCNT=40;
CHNAGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES;

Language
BCHLCNT e Defines the number of b-channels related to the
selected function.
ANTW d JA: Block-KOnfiguration abschließen
ANSW e YES: Finish block configuration
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
BGBKAN d Block fuer Baugruppe mit 60 und/oder 120 B-
Kanaelen
BRDBCHL e Dedicates the block for boards with 60 and/or 120
b-channels.
CONFIG d WEITER: Weitere Block-Konfiguration möglich
OK: Block-Konfiguration abschließen
CONFIG e CONT: Continue block configuration
OK: Finish block configuration
welcher auf dem CGW konfiguriert werden soll.
Anhand des Funktionsblocks wird die
Konfiguration der benötigten pyhsikalischen Lines
(Sätze der Baugruppe) festgelegt.
should be configured on the CGW board. With that
index the amount of needed physical lines (board
circuits) is calculated.
FUNCTION d Dieser Parameter legt das Konfigurationsprofile
des Common Gateways fest. Dabei muss die
benötigte HG3570 Funktion als erste angeführt
werden. Falls ein bestimmter Line-Bereich für die
Funktionen HG3530, HG3540 oder HG3550
entsprechende Funktion am Ende stehen und mit
dem Wert HG35xxR abgeschlossen sein. Die
Funktion STANDBY kann nur als Einzel-Funktion
FUNCTION e This parameter defines the configuration profile of
the CGW board. If HG3570 functionality is used, it
must be configured at first position. If a
prereservation of a certain line range of functions
HG3530, HG3540 or HG3550 is desired, this
function must be at the end of the profile just
suffixed by the according HG35xxR value. The
function STANDBY can only be configured as
single function.
BCSU
The modules are configured in the system and activated with the AMO BCSU.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Click New, enter data (IP Address, section IP Gateway, STMI Board Data
tab) and Save.
ADD-BCSU:MTYPE=IPGW,LTU=5,SLOT=91,PARTNO=Q2316-
X,FCTID=1,FCTBLK=1,IPADDR=192.168.1.11,BCHL3570=40;
CHANGE-BCSU:TYPE=HWYBDL,LTU=5,SLOT=91,PARTNO=Q2316-
X,HWYBDL=A;
IMPORTANT: Prior to ADD-BCSU, use ping to check that the IP addresses given
IPADDR must not respond as this would indicate that the corresponding address
has already been assigned.
IPADDR must be set differently for every board. The AMO does not verify if this
rule is observed.

Language
BCSU BKAN3570 d Anzahl der B-Kanaele fuer die IPDA (HG3570)
Funktion
BCHL3570 e Amount of b-channels for IPDA (HG3570)
function
LTG d LTG-Nummer
Parameter kann entfallen - oder muss auf 1
gesetzt werden.
LTG e Line/Trunk Group Number
Parameter can be omitted - or must be set to
1.
LTU d LTU-Nummer des Rahmens, in dem die HG 3500
eingesetzt wird.
Die HG 3500 darf nur in den Rahmen des HiPath
4000 Zentralsystems (LTU 1..15) eingesetzt
werden. Der Rahmen muss mit einer LTUCX
Baugruppe ausgestattet sein.
HG 3500 is plugged.
An HG 3500 may only be used in a shelf of the
HiPath 4000 central system (LTU 1..15). The
shelf must be equipped with a LTUCX board.
SACHNR d Sachnummer der HG 3500-Baugruppe
PARTNO e Part Number of the HG 3500 Board
FCTID d Function ID
FCTID e Function ID
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
LWVAR d LW Parametrisierung
Wird für HG 3500 nicht benötigt. Wert sollte
ausgelassen oder auf 0 gesetzt werden.
LWVAR e LW Parametrization
Not needed for HG 3500. Parameter should be
omitted or set to 0.
IPADR d IP-Adresse der HG 3500 Baugruppe
Segment gehören (siehe NETADR im AMO
SIPCO, Table 1 “AMO SIPCO parameters in ADD
branch or for CHANGE under TYPE=LSNET”)
IPADR muss für jede Baugruppe unterschiedlich
Regel.
IPADDR e IP Address of the HG 3500 Board
LAN Segment (see NETADDR in AMO SIPCO,
Table 1 “AMO SIPCO parameters in ADD branch
or for CHANGE under TYPE=LSNET” on page
2-576)
IPADDR must be different for every board. The
HWYBDL d Highway Bündel
Die HG 3500 / STMI2/4 Baugruppe unterstützt
die Wideband Technologie. Deshalb muss der
Baugruppe entweder das Highway Bündel A
(default) oder F zugewiesen werden.
HWYBDL e Highway Bundle
The HG 3500 / STMI2/4 board supports
wideband technology. Thus either highway
bundle A (default) or F must be assigned to this
board.
TYPE=IPGW d Baugruppentyp
IP Gateway = Common Gateway
MTYPE=IPG e board hardware type
W IP gateway = common GATEWAY
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Subscriber, CO/Tie Trunk Circuits in Access Points
2.4 Subscriber, CO/Tie Trunk Circuits in Access Points

In an IP distributed access point, all subscriber line and CO/tie trunk modules can
be used, with a few exceptions which are described in the HiPath 4000 Technical
Upgrade Plan
When using analog access modules which also require a ring generator, the
following must be taken into consideration:
In the 19“ access point AP 3500 IP and the AP 3505 IP expansion box, only RGM
type ring generator modules (S30807-Q6141-X or S30122-K5929-X) can be
used, not RG modules. The AP 3505 IP expansion box requires its own RGM
independently of the AP 3500 IP basic box, if analog access modules are to be
operated in it.
IMPORTANT: Trunk connections between access points in the same system or

between a central system and its access points are not permitted.
HiPath 4000 Tie trunk

AP 17
AP 18
IP Network Tie trunk
AP 19
Figure 19 Tie connections are not permitted within a system
With the configuration in an IP distributed access point, all circuits are given
additional parameters to govern their handling of Voice over IP. These IPDA
classmarks are:
Classmark Sprache/ Beschreibung/ Description

Language
EC d Echo Cancellation
EC e Echo Cancellation
G711 d Codec Typ G.711
G711 e Codec Type G.711
G729 d Codec Typ G.729A
Table 12 IPDA classmarks
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Classmark Sprache/ Beschreibung/ Description

Language
G729 e Codec Type G.729A
G729OPT d Codec Typ G.729A - optional
G729OPT e Codec Type G.729A - optional
INIT d stellt Default-Einstellung wieder her
INIT e restores default setting
KEINE d schaltet alle Classmarks aus
NONE e turns all Classmarks off
ML d Multiple Listener - Ansage wird auf einer Verbindung
übertragen und im Access Point an meherere Sätze
geschaltet.
*) nur für Ansagegeräte/MOH
ML e Multiple Listener - Announcement is transmitted on a single
connection and switched to multiple ports in the Access
Point.
*) only for Announcement Devices/MOH
VAD d Voice Activity Detection
VAD e Voice Activity Detection
VIAHHS d Payload über Zentralsystem
*) nur für Ansagegeräte/MOH
VIAHHS e Payload via central system
*) only for Announcement Devices/MOH
Table 12 IPDA classmarks
Details of the procedures that are switched with classmarks can be found in:
• Voice Compression - Section 5.2 on page 5-79 in the document “Gateways

HG 3500 and HG 3575”
• Voice Activity Detection (VAD) - Section 5.3 on page 5-81 in the document
“Gateways HG 3500 and HG 3575”
• Echo Cancellation - Section 5.5 on page 5-82 in the document “Gateways HG

3500 and HG 3575”
• Codec Standards - Section 2.3 on page 2-36 in the document “Gateways HG

3500 and HG 3575”
Handling the classmarks for a call

If a call is to be established between Subscriber A and Subscriber B, the
classmarks of both subscribers, or of the subscriber and the CO/tie trunk circuit
via which the subscriber is reached, are assessed.
Echo cancellation or voice activity detection is only activated if both circuits have
set the corresponding classmark.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Connections with announcement devices configured with the AMOs SSC, RCSU
or TSCSU are an exception to this rule. Here, the announcement device setting
is always adopted.
EC or VAD Circuit B EC or VAD Announcement Device

(RCSU)
NO YES NO YES
Circuit A NO NO NO Circuit A NO NO YES
YES NO YES YES NO YES
Table 13 Classmark handling for EC or VAD

In the case of codec types, only one type which supports both is selected.
In contrast to version 1, compression is now available for announcement devices

and conferences. As far as codec classmarks are concerned, conference trunk
circuits are assigned either G711 (default) or G711 & G729OPT when selecting
the codec type.
Circuit A Circuit B Codec type

used
G711 G729 G729OPT G711 G729 G729OPT
NO NO NO - - - NONE
NO NO YES - NO YES G.711
NO YES - YES NO - G.711
NO YES - - NO YES G.729
NO YES - - YES - G.729
YES NO NO YES - - G.711
YES NO YES YES NO YES G.711
YES NO YES YES YES - G.729
YES NO - NO YES - G.711
YES YES - YES NO YES G.729
YES YES - YES YES - G.729
YES - - YES NO NO G.711
- NO YES NO NO YES G.711
- NO YES NO YES - G.729
- YES - NO YES - G.729
- - - NO NO NO NONE
- Applies regardless of whether YES or NO is set
Table 14 Classmark handling for codec type
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Generating the classmarks

The default setting is always EC&G711&G729OPT.
IMPORTANT: The classmark setting in the CHANGE branches of the AMOs

overwrites the setting that existed prior to the AMO call. Therefore, if an additional
classmark is to be set, the existing setting must be displayed beforehand and
specified again with CHANGE.
If a setting is to be reset to its default value, the value INIT must be specified.
If all classmarks are to be deactivated, the value NONE must be used.
If only some classmarks are to be deactivated, the classmark to be retained must

be specified again with CHANGE. All others are automatically deleted.
Examples:
Subscriber:
Configuration Management --> Station --> Station

Click SEARCH and select the subscriber.
Set or delete the required classmarks on the Basic 2 tab under IPDA, IP
Connection Features and Save.
CHANGE-SDAT:STNO=54321,TYPE=DATA1,CLASSMRK=NONE;
Deactivates all classmarks as required for digital data terminal devices.
CHA-SDAT:STNO=54321,TYPE=DATA1,CLASSMRK=EC&G711&G729;
Sets the EC, G711 and G729 classmarks. Use of the G.729 codec is forced
if the partner has set G729 or G729OPT.
CHANGE-
SDAT:STNO=54321,TYPE=DATA1,CLASSMRK=EC&G711&G729&G729O
PT&VAD;
Sets the classmarks for EC, G711, G729, G729OPT and VAD (in other
words, all).
Attendant console:
Administration of the attendant console can only be executed in expert

mode.
(see AMO command)
CHANGE-ACSU:ATNDNO=65432,CLASSMRK=EC&G711;
Sets the EC and G711 classmarks. Calls are always switched without
compression and the echo is suppressed.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Announcement devices:
The default setting for AMO SSC and AMO RCSU is always
G711&G729OPT&VIAHHS&ML.
The default setting for AMO TSCSU is EC&G711&G729OPT&VIAHHS&ML.
IMPORTANT: The option of setting G729OPT or even G729 for announcement

devices should only be used after careful consideration. G.729 specifies a codec
for voice compression. The codec is totally unsuitable for music compression.
Music playback is extremely distorted with G.729. In some cases it may be
necessary to disable G729OPT particularly if you want to avoid distortions and if
circuits have been configured with codec G729.
Configuration Management --> Station --> Special Stations

Click Search and select the special station (Station Type: EXTANS).
Set or delete the required classmarks on the Features tab and Save.
ADD-SSC:PEN=1-2-37-
10,TYPE=EXTANS,CPCALL=HOLD,CLASSMRK=G711&VIAHHS&ML;
or
CHANGE-RCSU:PEN=1-2-37-5,CLASSMRK=G711&VIAHHS&ML;
Disables G729OPT and sets the G711 classmark. Echo cancellation is not
required at announcement devices because the path from the subscriber to
the announcement device is not switched.
IMPORTANT: The classmarks VIAHHS and ML are enabled by default.

They may only be disabled in exceptional cases. 
In the case of CHANGE, do not forget to specify both classmarks if they were previ-
ously set.
If VIAHHS is not set, announcements and/or music on hold are no longer

distributed via the HiPath 4000 host system. Instead they are transferred directly
from the HG 3575 which hosts the source to all other HG 3575 systems that
require the announcement.
If ML is not set, an individual connection is established from the source HG 3575

for each circuit in an access point that requires an announcement or music on
hold.
For further information on announcements or music on hold, refer to Section 2.12,

“External Music on Hold”.
Conference:
A central configuration switch is used system-wide to set whether or not

compressed connections can be connected to conference units.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
By default, only uncompressed RTO connections are supported with conference

units. In other words, the codec classmarks associated with the conference units
are set to G711.
You can use the AMO ZAND to change the setting to G711 & G729OPT.
Administration of central system data can only be executed in expert mode.

Expert Mode --> HiPath 4000 Expert Access --> Open ...<IP> with AMO
(see AMO command)
CHANGE-ZAND:TYPE=ALLDATA3,IPDAVCCF=YES;
This AMO permits compressed connections with the conference unit.
The change becomes effective immediately, that is, the next time an IP
connection is connected to a conference unit.
CO/tie trunks:
Configuration Management --> System Data --> Trunk --> Trunk

Click Search and select the circuit.
Set or delete the classmarks for IP connections on the Basic Data tab and
Save.
CHANGE-TACSU:PEN=1-1-91-1,CLASSMRK=EC&G711;
Sets the EC and G711 classmarks. (G729OPT has effectively been
deactivated in contrast to the default setting.)
CHANGE-TDCSU:PEN=1-1-91-1,CLASSMRK=G711;
Sets the G711 classmark.
IMPORTANT: If the classmark setting “NONE“ is temporarily required for an

outbound call (e.g. for privacy module), this can be done using an access code:
AMO WABE: NOEC. This code can only be used as the prefix.
Example
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Compressed PC
Path Data
G711
&EC G711 NONE
Other &EC
System G711
HG &G729OPT
G711 3570
&G729OPT
&EC LAN HG Peripheral
3575 Boards
HG
G711 3570
HiPath 4000 LAN segment
AP 17
&EC
G711 Public
&G729OPT Peripheral
Boards WAN Network
&EC
G711 G711 G711
G711 &G729 &EC &G729
Public &G729OPT &EC &EC
Network &EC Control LAN
G711 HiPath 4000

HG Peripheral
3575 Boards
AP 35
VoiceMail/PhoneMail/Expression
digitally connected
Figure 20 Classmarks
The example in Figure 20 “Classmarks” shows how classmarks are set for
different circuits.
The default is G711&G729OPT&EC.
In the central system, there are three exceptions: the fax which does not tolerate
signal compression, the compressed tie trunk path and the digital VoiceMail/
PhoneMail/Expression server connected. Fax devices can also be configured
with the default classmarks if STMI2/4 and NCUI2/4 boards are used exclusively.
A sequence of compressions and expansions should be avoided. The selected
G711&EC setting in the example ensures that calls from the compressed tie trunk
path cannot be compressed a second time. Digital announcement/voice
recording devices connected generate absolutely no echo - and save voice in
compressed form. Consequently, compression is disabled and EC is deactivated.
The data terminal device on the AP 17 is set to NONE, as it tolerates neither

compression nor echo cancellation or attenuation/amplification. When the ISDN
service is signaled correctly in the bearer capabilities, transmission is always
performed with the NONE classmark, irrespective of the classmark setting.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
The Optiset with privacy module for voice encryption is configured for G711&EC.
If you switch to encryption, that is, modem transmission, during a call, the
gateways automatically adapt the transmission mode. The classmarks G729 or
G729OPT must not be set for version 1 boards, that is, STMI/NCUI (and not
STMI2/4 or NCUI2/4), because these only support automatic fax/modem
recognition in uncompressed connections. This restriction does not apply to
STMI2/4 and NCUI2/4 boards.
The AP 35 is connected to the central system via WAN. Bandwidth is therefore a

precious commodity and voice compression should always be used if possible.
The setting G711&G729&EC for telephones and the CO line ensures that calls
with telephone subscribers in the central system and AP 17 are compressed, as
are calls from telephones in the central system or AP 17 via the local CO line in
AP 35.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
2.5 Special Routes

The usual demands made on the routing between access points and HG 3500
modules in the central HiPath 4000 switch are fully met by the administration
described above. A default router (AMO SIPCO, parameter DEFRT) serves the
HiPath 3500 processors as an access to the IP world beyond the HiPath 4000
LAN segment. One default router per LAN segment in which access points are
located serves the access points as a bridge to other network segments.
However, additional demands may be imposed by the specific network

architecture of the customer.
A distinction is to be made between 2 basic scenarios in this context:
• Links between LAN segments containing access points which do not lead to
the respective LAN segments via the default router.
• Links from the HiPath 4000 LAN segment to LAN segments containing
access points which do not lead to the HiPath 4000 LAN segment via the
default router.
The difference is that, in the first case, only HG 3575 routing tables are affected,
while in the second case, the routing tables of all HG 3500 modules, as well as
the CC computer and the HiPath 4000 Assistant, are also affected.
The routing tables of the HG 3500 and HG 3575 allow the configuration of 8
routes (in addition to default routes which do not appear in the routing table).
These are configured by specifying a target (IP) address, the netmask of the
target network and the IP address of the router port to be accessed by the source
module.
It must be ensured that:
• no duplicate routes are entered, e.g.
192.168.23.99 , 255.255.255.0 , 192.168.22.2

192.168.23.98 , 255.255.255.0 , 192.168.22.2
The first entry already leads the route into the entire network segment
192.168.23.X via the router port 192.168.22.2. The second entry would
achieve precisely the same and, therefore, must be suppressed.
• the configuration of the route from A to B remains in place without influencing

the route from B to A.
In other words, a route back to the source must generally also be configured
in the target module, e.g.
192.168.22.43 , 255.255.255.0 , 192.168.23.2
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
2.5.1 Special Routes Between Access Points
APIPADDR
192.168.23.99
AP 99
HG
STMI-1 STMI-2
Peripheral
HG
3500
APIPADDR 3575 Boards
Ra 192.168.23.98
Rx AP 3300 IP, AP 3500/3505
Router Router
HG ROUTER1
AP 98
3500 HG Peripheral
H i Pa t h 400 0 LA N Segm e nt
192.168.23.2 3575 Boards
Router
I P n e two r k AP 3300 IP, AP
AP 3500/3505
3500/3505
Rz
Peripheral
Boards
ROUTER1
Ry
AP 43
192.168.22.2 HG Peripheral
Router 3575 Boards
ADP APIPADDR AP 3300 IP

IP,, AP
AP 3500/3505
3500/3505
Atlantic LAN
192.168.22.43
AP 18
HG Peripheral
CC-A 3575 Boards
R1
Router AP 3300 IP, AP 3500/3505
PSTN Network
CC-B
AP 17
R10 HG Peripheral
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assis
tant
HiPath
4000
Figure 21 Special routes between access points
Generation
The configuration of special routes in HG 3575 (NCUI2/4S) is realized with the
AMO APRT in the ROUTTBL branch.
Configuring the scenario illustrated in Figure 21 “Special routes between access

points”:

Additional Routing
Click New if there are no existing entries. Enter LTU.
Enter the IP addresses of the destinations and routers, enter the network
masks in the routing table and Save.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
CHANGE-APRT:TYPE=ROUTTBL,MTYPE=NCUI,LTU=99,
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.23.2;
Sets the route from AP99 to AP43 via Router Rz.
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.23.2;
Sets the route from AP98 to AP43 via Router Rz.
DSTADDR1=192.168.23.99,DSTMSK1=255.255.255.0,
ROUTER1=192.168.22.2;
Sets the route from AP43 to AP99 - and AP98 - via Router Rz.
In this example, the first of the 8 routing table entries was used in all 3 modules.
Of course, this presupposes that these entries have not yet been used.
If the first 2 entries had already been used in AP43, the following would need to
be done:

Additional Routing
Click Search and select LTU.
Enter the IP addresses in line 3 of the routing table and Save.
DSTADDR3=192.168.23.99,DSTMSK3=255.255.255.0,
ROUTER3=192.168.22.2;
Table 16 “AMO APRT parameters in CHANGE branch under TYPE=ROUTTBL”

provides a precise description of the parameters.
If a ROUTTBL entry is to be deleted (e.g. the second entry in AP43), this is

realized as follows:

Additional Routing
Click Search and select LTU.
Delete the IP addresses in the second line of the routing table and Save.
Data
DELETE-APRT:TYPE=ROUTTBL,MTYPE=NCUI,LTU=43,INDEX=2;
In order for these changes to become effective in the access point, this has
to be restarted with

system hard disk.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
2.5.2 Special Routes between Access Point and

192.168.1.254 192.168.23.1 192.168.23.99
AP 99
STMI-1 STMI-2 HG Peripheral
HG 3575 Boards
3500
Ra IP Net wo r k A Rx AP 3300 IP, AP 3500/3505
Router
HG Router 192.168.23.98
AP 98
3500 192.168.23.2 HG Peripheral
HiPath 4000 LAN Segment 3575 Boards
Router
Rb AP 3300 IP, AP 3500/3505
Rz
Peripheral Router
Boards
IP Network B 192.168.22.43
Ry HG
AP 43
Peripheral
192.168.1.253 3575 Boards
Router
AP 3300 IP, AP 3500/3505
192.168.22.1
Atlantic LAN
ADP
192.168.22.2
AP 18
HG Peripheral
3575 Boards
CC-A R1
AP 3300 IP, AP 3500/3505
Router
PSTN Network
AP 17
CC-B R10 HG Peripheral
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assis
tant
HiPath
4000
Figure 22 Special routes between access point and HiPath 4000 LAN segment
This complicated scenario is based on the simple case of the special route
between 2 access points. In addition, the IP network of the customer in this case
is broken down into 2 sub-networks which are not, or only, linked to one another
via the HiPath 4000 LAN segment.
This scenario assumes that the routers a, x and y are the default routers (for
HiPath 4000 components) in the respective networks.
Without additional routes, neither the HG 3500, nor the “direct link“ access points
AP17 and AP18 can reach access point AP 43.
The configuration for the entire scenario is realized according to the following
steps:
• Configure Router Ra as the default router for all HG 3500 modules
Data
Click Search and enter the default router address, then Save.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
ADD-SIPCO: ... DEFRT=192.168.1.254 ...; 
• Configure Router Ra as the default router for AP17 and AP18
Point
Enter the router address on the IP Interface (DL) tab, then Save.
ADD-UCSU:UNIT=AP,LTU=17, ... APRTADDR=192.168.1.254
...;
and
ADD-UCSU:UNIT=AP,LTU=18, ... APRTADDR=192.168.1.254
...;
• Configure Router Rx as the default router for AP98 and AP99 and specify
Router Ra as the route for the signaling messages of the CC-A and CC-B,
respectively
Point
Enter the router addresses on the IP Interface (NW) tab, then Save.
CHANGE-UCSU:UNIT=AP,LTU=98, ...
LSRTADDR=192.168.1.254,APRTADDR=192.168.23.1 ...;
and
ADD-UCSU:UNIT=AP,LTU=99, ...
• Configure Router Ry as the default router for AP43 and specify Router Rb as
the route for the signaling messages of the CC-A and CC-B, respectively
Point
Enter the router addresses on the IP Interface (NW) tab, then Save.
ADD-UCSU:UNIT=AP,LTU=43, ...
The payload between AP43 and AP98/AP99 would now be routed via Router Ry
-> Router Rb -> Router Ra -> Router Rx. The shortcut via Router Rz is configured
as in the previous example with:
• Set the routes from AP43 to AP98/AP99 via Router Rz

Additional
Routing
Click Search, select the access point, enter or change IP addresses, then
click Save.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
DSTADDR1=192.168.23.99,DSTMSK1=255.255.255.0,
ROUTER1=192.168.22.2;
For the payload route from AP98/AP99 to AP43, special routes likewise have to
be configured:
• Set the routes from AP98/AP99 to AP43 via Router Rz

Additional
Routing
Click Search, select the access point, enter or change IP addresses, then
click Save.
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.23.2;
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.23.2;
The payload from the HG 3500 to AP98/AP99 is routed via the default router, Ra.
The route is already specified with ADD-SIPCO.
The payload from AP98/AP99 to the HG 3500 is routed via the default router, Rx.
The route is already specified with ADD-UCSU.
However, for the payload transport from the HG 3500 to AP43, the route is still
missing. In this case, a special route has to be configured for all HG 3500s
(STMI2/4) via Router Rb:
• Set the route from the HG 3500 to AP43 via Router Rb

Additional
Routing
Click Search, enter or change network mask, destination and router
addresses, then click Save.
CHANGE-APRT:TYPE=ROUTTBL,MTYPE=STMI,
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.1.253;
The payload from AP43 to the HG 3500 is routed via the default router, Ry. The
route is already specified with ADD-UCSU.
The payload between the HG 3500 and the “direct link“ access points AP17/AP18
and back remains within the HiPath 4000 LAN segment and requires no
additional routes.
The payload between the “direct link” access points AP17/AP18 and AP98/AP99
and back is routed via the route specified with ADD-UCSU. (Ra, Rx)
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
However, for the payload transport from the “direct link“ access points AP17/
AP18 and AP43, the route is still missing. In this case, a special route has to be
configured via Router Rb:
• Set the routes from AP17/AP18 to AP43 via Router Rb

Additional
Routing
Click Search, select the access point, enter or change network mask,
destination and router addresses, then click Save.
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.1.253;
DSTADDR1=192.168.22.43,DSTMSK1=255.255.255.0,
ROUTER1=192.168.1.253;
The payload from AP43 to AP17/AP18 is routed via the default router, Ry, and no
additional routes need to be configured.
In order for these changes to become effective in the access points, these have
to be restarted.
Data

system hard disk.
In order for these changes to become effective in the HG 3500, all HG 3500
modules have to be restarted.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes
Configuration Management --> System Data --> Maintenance --> Board

Maintenance
with OK.
RESTART-BSSU:ADDRTYPE=PARTNO,PARTNO=Q2316-X,FCTID=1;
In order to maintain an overview in these somewhat more complex scenarios, the

creation of a communications matrix is recommended:
to CC-A CC-B HG AP 17 AP 18 AP 43 AP 98 AP 99
from 3500
CC-A - - - direct direct Rb Ra Ra
CC-B - - - direct direct Rb Ra Ra
HG 3500 - - - direct direct Rb Ra Ra
AP 17 direct direct direct - direct Rb Ra Ra
AP 18 direct direct direct direct - Rb Ra Ra
AP 43 Ry Ry Ry Ry Ry - Rz Rz
AP 98 Rx Rx Rx Rx Rx Rz - direct
AP 99 Rx Rx Rx Rx Rx Rz direct -
Table 15 Communication matrix for special routes between access point and
HiPath 4000 LAN segment”
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes

Language
APRT MTYP d Modul Typ
Hier wird zwischen STMI2/4 (HG 3500) und NCUI2/
4 (HG 3575) unterschieden.
MTYP=STMI:
Diese Routing Table gilt für alle STMI2/4 im System
gleichermaßen.
DSTADRx darf nicht zum HiPath 4000 LAN Segment
gehören.
ROUTERx muss zum HiPath 4000 LAN Segment
gehören.
(siehe NETADR im AMO SIPCO, Table 1 “AMO
SIPCO parameters in ADD branch or for CHANGE
under TYPE=LSNET”)
MTYP=NCUI:
Diese Routing Tabelle gilt nur für die durch LTU
angegebene NCUI2/4.
Bei Routen zwischen 2 NCUI2/4 müssen bei beiden
NCUI2/4 die entsprechenden Einträge gemacht
werden!
MTYPE e Modul Type
This is to distinguish between STMI2/4 (HG 3500)
and NCUI2/4 (HG 3575).
MTYPE=STMI:
This routing table is common to all the STMIs in the
system.
DSTADRx must not belong to the HiPath 4000 LAN
Segment.
ROUTERx must belong to the HiPath 4000 LAN
Segment.
(see NETADDR in AMO SIPCO, Table 1 “AMO
SIPCO parameters in ADD branch or for CHANGE
under TYPE=LSNET”)
MTYPE=NCUI:
This routing table is valid only for the NCUI2/4
assigned by LTU.
For routes between 2 NCUI2/4 entries must be made
for both NCUI2/4 respectively!
DSTADR1 d Zieladresse der 1. Route.
Legt die Adresse fest, die über die im 1. Eintrag
spezifizierte Route erreicht werden soll. Das kann
eine Host- oder auch eine Netzadresse sein. Die
DSTMSK1 erlaubt die Interpretation.
DSTADDR1 e Destination Address for the 1st Route.
Assigns the address to be reached using the route
defined in the 1. entry. It may be a host or a network
address. DSTMSK1 allows the interpretation.
DSTMSK1 d Netzmaske des Netzes, dem DSTADR1 angehört
DSTMSK1 e Netmask of the network which DSTADDR1 is part of
Table 16 AMO APRT parameters in CHANGE branch under

TYPE=ROUTTBL
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes

Language
ROUTER1 d IP-Adresse des Routers, über den Pakete an
DSTADR1 gesendet werden sollen.
Segment gehören (siehe NETADR im AMO SIPCO,
Table 1 “AMO SIPCO parameters in ADD branch or
for CHANGE under TYPE=LSNET”)
ROUTER1 e IP Address of the Router via which Packets to
DSTADDR1 are to be sent.
This IP address must belong to the HiPath 4000 LAN
Segment (see NETADDR in AMO SIPCO, Table 1
“AMO SIPCO parameters in ADD branch or for
CHANGE under TYPE=LSNET”)
DSTADDR2 e Destination Address for the 2nd Route.
DSTADDR3 e Destination Address for the 3rd Route.
DSTADDR4 e Destination Address for the 4th Route.
TYPE=ROUTTBL
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Special Routes

Language
DSTADDR6 e Destination Address for the 6thRoute.

TYPE=ROUTTBL
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Signaling Survivability
2.6 Signaling Survivability

Signaling Survivability has been moved to an own section within the IP Solutions:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Quality Monitoring for the Signaling Connection over IP
2.7 Quality Monitoring for the Signaling Connection over IP

As already described in the section Signaling Survivability, you cannot operate an
access point unless the signaling connection is working properly.
The concept introduced with HiPath 4000 version 1.0 for monitoring the signaling
connection uses the additional monitoring connection to verify if communication
is basically possible between CC and an access point. The main advantage of
this is that you can respond very quickly and activate signaling survivability in the
event of a crash on the IP connection between CC and the access point.
The IP connection between the CC and access point is sometimes not completely
severed, “just“ severely restricted. This can have an extremely negative impact
on the signaling function without this malfunction being detected by the separate
monitoring connection.
To eliminate this restriction, we have introduced a new mechanism for monitoring

the actual signaling connection to complement the mechanism already described
and based on a separate monitoring connection.
This additional functionality is split into five components:
• Restriction of the Available Signaling Bandwidth (Traffic Shaping)
• Monitoring the Runtime for Signaling Messages (Round Trip Delay)
• Monitoring Message Throughput
• Advanced Criteria for Signaling Survivability
• Output of Statistical Information on the Signaling Connection
2.7.1 Restriction of the Available Signaling

Bandwidth (Traffic Shaping)
The signaling bandwidth for controlling an access points is not particularly large
and fluctuates very heavily. A flat rate of 64 Kbps is required for the signaling
connection, although in some configurations a lower bandwidth (e.g. 32 Kbps)
would be sufficient for normal business hours, i.e. to controll the call processing/
access point.
Bandwidth requirements spike briefly when a call processing action triggers

numerous parallel follow-up actions in the peripherals. Several large packets
containing signaling information can be sent to an access point in a short period
of time.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
During startup/installation of an access point there is also more bandwidth

needed (e.g. FTP loadwre transfer for NCUI board and other periperal boards)
and as a consequence there must be a minimum bandwidth of 64 Kbps for TCP
signaling available/guaranteed (same bandwidth available via ISDN modem, i.e.
signaling survivability).
For a WAN router with a very low available bandwidth for this signaling
connection (e.g. 64 Kbps), this means that while the first packet from this burst is
being sent, another is being received. The router may not have enough buffer
space to buffer the packets. As a result, packets from this “burst“ are rejected by
the router and have to be resent later by the CC.
Restricting the signaling bandwidth to an access point in the CC prevents a burst

from occurring when packets are immediately sent one after the other from the
CC. This is done by staggering the packets so that they are sent at intervals that
prevent buffer overflow in the router.
Transmission without signaling bandwidth restriction
CC time of transmission
Receive buffer in the router

Buffer Buffer overflow - packet 3 is lost
Packet transmission in the WAN
Transmission with signaling bandwidth restriction
CC time of transmission
Receive buffer in the router

Buffer Buffer Buffer
Packet transmission in the WAN

t
Figure 23 Signaling connection with/without bandwidth restriction
IMPORTANT: If there is only a bandwidth of between 64 and 250 Kbps available

for signaling to an access point in the IP network, then signaling bandwidth
restriction must be activated (AMO STMIB, parameter SIGQOS) in the CC and
set to the value available in the network.
The signaling bandwidth restriction delays signaling messages in the CC and

sometimes results in a backlog of several messages. If a backlog of this kind
persists for several seconds, the signaling bandwidth configured is too low. The
system issues the error message F8292 (see Table 16 “F8292 - Bandwidth
Requirement Exceeds Limit”) that marks the beginning of backlog. The
publication of a message status can also be a criteria for changing from the
signaling path to the signaling survivability path (see Section 2.7.4, “Advanced
Criteria for Signaling Survivability”).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
The message F8293 is output to signal that the backlog has cleared (see Section
2.7.6.6, “F8293 - Bandwidth Required Back Below Limit”).
The restriction of the signaling bandwidth only affects the signaling path over
LAN. The modem connection is not affected in the case of signaling survivability.
IMPORTANT: Under-dimensioning the signaling bandwidth can lead to a

message buffer deficit which results in a access point reset. All connections are
then cleared down.

The system outputs the error message F8292 as soon as under-dimensioning is
detected during live operation (see Section 2.7.6.5, “F8292 - Bandwidth
Requirement Exceeds Limit”). The actual available signaling bandwidth in the
customer network must be increased in response to this message. Ignoring
these early warning signals can result in the mentioned access point reset or
other major issues.

Furthermore a restriction of the bandwidth in the TCP can cause long delays
during loading the loadware and setting up the shelf/system!
Procedure
At the start of each second, a transmission credit with the value of the signaling
bandwidth configured is made available for use. If the setting is 64 Kbps, for
example, 8000 bytes may be transmitted every second. For every packet to be
sent, the credit is now reduced by the packet size. If there is not enough credit
left, the packet is delayed until sufficient credit is available.
When the second expires, the remaining transmission credit is cancelled. The
next second then starts again with a new credit for the value of the signaling
bandwidth configured, for example, 8000 bytes. Returned packets can now be
sent.
The transmission bandwidth is restricted at “application level“, in other words,

over the TCP/IP stack.
Generation
Click Search and enter or change the bandwidth on the Quality of Service
tab in the Signaling Quality of Service section, then Save.
CHANGE-STMIB:MTYPE=NCUI2,TYPE=SIGQOS,LTU=99,BANDW=64;
The signaling bandwidth is expressed in kilobits per second (Kbps). The value
BANDW=0 disables signaling bandwidth restriction (default configuration). The
setting becomes effective immediately.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.2 Monitoring the Runtime for Signaling Messages

(Round Trip Delay)
If a malfunction occurs in the IP network, the effective bandwidth available drops
and the time between the dispatch of a message and receipt acknowledgement
rises.
A maximum permissible message runtime can be defined for the signaling

connection for every access point. This runtime includes the entire time from
sending the message to receiving the acknowledgement, in other words, the
“Round Trip Delay“. The runtime is evaluated with every signaling message.
Measurement is therefore independent of the signaling load.
If the runtime exceeds the limit set, the system outputs the error message F8290
(see Section 2.7.6.2, “F8290 - Net Weakness Start Message Runtime
Exceeded”). The exceeding of the maximum message runtime can also be a
criteria for changing from the signaling path to the signaling survivability path (see
Section 2.7.4, “Advanced Criteria for Signaling Survivability”).
The message F8291 is output to signal a return by the runtime to permitted values
(see Section 2.7.6.4, “F8291 - Net Weakness End”).
Monitoring the maximum message runtime is only active on the signaling path
over LAN. The modem connection is not affected in the case of signaling
survivability.
Procedure
An average runtime value is calculated and stored every three seconds for all
messages acknowledged in this interval.
The three-second average values are used to generate further average values
over a short (15 seconds: SHORT) and long monitoring time (60 seconds:
LONG).
The error message is generated whenever either of the two values (SHORT/
LONG) exceeds the limit configured.
The limit is set for the long monitoring duration (LONG). The limit for the short
duration (SHORT) is set to factor 1.5 times the value.
The SHORT interval makes sense with a higher limit because if the network
quality jumps, the system can respond faster, that is, within 15 seconds. This
interval would be 60 seconds in the case of exact measurement.
The measurement is made at “application level“, in other words, over the TCP/IP
stack. On account of stack dynamics, measured values cannot be compared
directly with values that are measured directly on the network.
The runtime includes:
• Sender of packet from TCP level in the HiPath 4000 central system
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• Transmission of packet in the network
• Receipt of packet on HG 3575 up to TCP
• Creation and sending of acknowledgement on the HG 3575
• Transmission of acknowledgement in the network
• Receipt of acknowledgement in the HiPath 4000 central system
Since TCP can delay the acknowledgement of a packet in order to combine the
acknowledgement with that of another packet, values under 400 ms are
impractical.
Keep alive packets are not included in the measurement. If no packets are sent
or acknowledged within a 3-second interval, a long-term mean value is used that
is determined by the TCP.
Generation
Click Search and enter or change the maximum runtime on the Quality of
Service tab in the Signaling Quality of Service section, then Save.
CHA-STMIB:MTYPE=NCUI2,TYPE=SIGQOS,LTU=99,MAXRTD=500;
The message runtime is expressed here in milliseconds. The value MAXRTD=0

disables message runtime monitoring. The setting becomes effective
immediately.
IMPORTANT: Measurements are performed at 10-ms intervals. As a result, it

only makes sense to set values divisible by 10 (without remainder), for example,
400, 410, 420, etc.
2.7.3 Monitoring Message Throughput

A minimum necessary message throughput can be defined for the signaling
connection for every access point. The throughput measurement includes the
volume of all messages sent by the CC.
The undershooting of the minimum necessary message throughput only takes

account of the times when the specified load at least was used. An undershooting
of the minimum message throughput is ignored because the number of
messages available for transmission is not sufficient.
If the throughput falls short of the threshold value set, the system outputs the error
message F8290 (see Section 2.7.6.3, “F8290 - Net Weakness Start Message
Throughput Undershot”). The undershooting of the minimum message
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
throughput can also be a criteria for changing from the signaling path to the
signaling survivability path (see Section 2.7.4, “Advanced Criteria for Signaling
Survivability”).
The message F8291 is output to signal a return by the message throughput to

permitted values (see Section 2.7.6.4, “F8291 - Net Weakness End”).
Monitoring the minimum message throughput is only active on the signaling path
over LAN. The modem connection is not affected in the case of signaling
survivability.
Procedure
Every three seconds the system calculates the number of bytes sent during this
interval. The result is then used to calculate the throughput in Kbps. (Bytes sent
* 8/3)
The three-second values are used to generate average values over a short (15
seconds: SHORT) and long monitoring time (60 seconds: LONG).
The error message is generated whenever either of the two values (SHORT/
LONG) exceeds the limit configured.
The limit is set for the long monitoring duration (LONG). The limit for the short
duration (SHORT) is set to 2/3 of the LONG value.
The SHORT interval makes sense with a lower limit because if the network quality
jumps, the system can respond faster, that is, within 15 seconds. This interval
would be 60 seconds in the case of exact measurement.
The measurement is made at “application level“, in other words, over the TCP/IP
stack. On account of stack dynamics, measured values cannot be compared
directly with values that are measured directly on the network.
Generation
Click Search and enter or change the minimum message throughput on the
Quality of Service tab in the Signaling Quality of Service section, then
Save.
CHA-STMIB:MTYPE=NCUI2,TYPE=SIGQOS,LTU=99,MINTHRPT=32;
The minimum message throughput is expressed here in Kbps. The value

MINTHRPT=0 disables message throughput monitoring. The setting becomes
effective immediately.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.4 Advanced Criteria for Signaling Survivability

The restriction and monitoring functions described in Section 2.7.1, “Restriction
of the Available Signaling Bandwidth (Traffic Shaping)” to Section 2.7.3,
“Monitoring Message Throughput” can trigger the signaling path switchover from
LAN to modem.
The events that should activate signaling survivability are set for each access
point in the course of configuration.
The following options are available:
• Switching over the signaling path to modem in the event of loss of monitoring
connection - [STD]
In STanDard mode, the signaling path is switched back to LAN as soon as
stability returns to the monitoring connection.
• Switching over the signaling path to modem in the event of loss of the
monitoring connection or violation of the criteria from monitoring the quality of
the signaling connection - [EXTENDED]
In EXTENDED mode, the signaling path is switched back to LAN as soon as
stability returns to the monitoring connection and the quality criteria are
satisfied. To measure the quality criteria, a load is periodically generated on
the monitoring connection which must at least be able to transport the
signaling connection after reverting to LAN.
IMPORTANT: When using EXTENDED mode, the bandwidth available must

be taken into consideration on the signaling path over modem. There is no
point in switching to a 28.8-Kbps modem connection because the minimum
throughput for the LAN connection falls short of 64 Kbps.
• Exclusive use of the signaling path on modem - [SURVONLY]

SURVONLY mode permits the administrative switchover of the signaling path
to modem irrespective of behavior on the LAN connection. This can be used
for stable switchover when performing planned maintenance in the LAN/WAN
environment for the duration of the maintenance work. Switching back is then
performed in STanDard or EXTENDED mode
IMPORTANT: Even in the case of administrative activation of signaling

survivability for an access point, the establishment of new payload connec-
tions is blocked in the HiPath 4000 CC (to all HG 3500s).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Generation
Click Search and select the switchover mode for signaling survivability on the
Quality of Service tab in the Signaling Quality of Service section, then
Save.
CHA-
STMIB:MTYPE=NCUI2,TYPE=SIGQOS,LTU=99,SIGPTHSW=EXTENDED;
The setting becomes effective immediately.
2.7.5 Output of Statistical Information on the

Signaling Connection
If monitoring is active for the message runtime or the message throughput, the
system only signals the results of measurements if limits are breached.
It is therefore very difficult to say if the limits configured were set too low or even
much too high.
For this reason, the cyclical output of measurement data can be set at the
operating terminal.
You can set whether or not measurement data should be output cyclically for
every access point.
Data is only output, however, if
• monitoring is active for the message runtime or the message throughput
• output is generally enabled with the AMO-DIAGS (CC/HSR option S00)
The measurement data are output with the message F8289
IMPORTANT: The cyclical query and output of measurement data generates a

high load in the system. There is also a danger that important error messages will
be overlooked in the surge of measurement data.
As a result, the output of measurement data may only be selectively used for a
limited number of access points simultaneously. The output release should only
be used for a manageable period of time.
For further information (e.g. generation) please refer to Gateways HG 3500 and
HG 3575 > Section 12.11, “TYPE SIGQOS - Quality Monitoring for the
Signaling Connection over IP”.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.6 Error Messages from Quality Monitoring for the

Signaling Connection over IP
2.7.6.1 F8289 - Output of Statistics Data
F8289 M4 N0367 NO ACT BPA TRANSSYS NET STATISTICS DATA 04-06-07 12:52:09
FORMAT:49
Message contains statistical data
AP NUMBER: 99 - ROUND TRIP DELAY VALUES concerning the message runtime
CONFIGURED : SHORT = 0800 LONG = 0400 (Round Trip Delay)
AVERAGE : SHORT = 0520 LONG = 0000
HISTORY:
0500 0500 0500 0500 0610 0350 0350 0350 0350 0490 Measured values in the last
0160 0160 0160 0160 0130 0200 0200 0200 0200 0000 30 three-second intervals.
0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 Expressed in milliseconds,
latest value first
Average values measures for the 15-second (SHORT) or the 60-second (LONG) interval.
Specified in milliseconds.
Configured limits for the 15-second (SHORT) or the 60-second (LONG) interval. LONG in this case is
the value set with the parameter MAXRTD and SHORT is 1.5x LONG. Expressed in milliseconds.
Time assignment of history data.

Zero values indicate intervals in which there were no packets to be sent
3s 6s 9 s 12 s 15 s 18 s 21 s 24 s 27 s 30 s
33 s 36 s 39 s 42 s 45 s 48 s 51 s 54 s 57 s 60 s
63 s 66 s 69 s 72 s 75 s 78 s 81 s 84 s 87 s 90 s
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
F8289 M4 N0368 NO ACT BPA TRANSSYS NET STATISTICS DATA 04-06-07 12:52:09
FORMAT:49
AP NUMBER: 99 - THROUGHPUT VALUES concerning message throughput.
CONFIGURED : SHORT = 0010 LONG = 0015
HISTORY:
0021 0041 0024 0035 0036 0025 0031 0034 0024 0018 Expressed in Kbps,
latest value first
Expressed in milliseconds.
the value set with the parameter MINTHRPT and SHORT is 2/3 of LONG. Expressed in milliseconds.

3s 6s 9 s 12 s 15 s 18 s 21 s 24 s 27 s 30 s
33 s 36 s 39 s 42 s 45 s 48 s 51 s 54 s 57 s 60 s
63 s 66 s 69 s 72 s 75 s 78 s 81 s 84 s 87 s 90 s
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.6.2 F8290 - Net Weakness Start Message Runtime

Exceeded
F8290 M4 N0372 NO ACT BPA TRANSSYS NET WEAKNESS BEGIN 04-06-07 12:52:23
Start of net weakness
FORMAT:49
AP NUMBER: 99 - ROUND TRIP DELAY VALUES
CONFIGURED : SHORT = 0800 LONG = 0400 concerning the message runtime
AVERAGE : SHORT = 0590 LONG = 0410 (Round Trip Delay)
HISTORY:
0200 0200 0200 0200 0000 0000 0000 0000 0000 0000 Expressed in milliseconds,
LONG INTERVAL VIOLATION latest value first
Reason for message - here: the limit for the 60-

second (LONG) interval was exceeded
Expressed in milliseconds.
the value set with the parameter MAXRTD and SHORT is 1.5x LONG. Expressed in milliseconds.

3s 6s 9 s 12 s 15 s 18 s 21 s 24 s 27 s 30 s
33 s 36 s 39 s 42 s 45 s 48 s 51 s 54 s 57 s 60 s
63 s 66 s 69 s 72 s 75 s 78 s 81 s 84 s 87 s 90 s
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.6.3 F8290 - Net Weakness Start Message Throughput

Undershot
F8290 M4 N0448 NO ACT BPA TRANSSYS NET WEAKNESS BEGIN 04-06-07 13:10:13
FORMAT:49
Start of net weakness
AP NUMBER: 99 - THROUGHPUT VALUES Message contains statistical data
CONFIGURED : SHORT = 0010 LONG = 0015 concerning message throughput.
HISTORY:
0014 0014 0011 0013 0015 0010 0014 0014 0014 0014 Measured values in the last 30 three-
0011 0014 0012 0013 0014 0014 0009 0015 0013 0030 second intervals. Expressed in Kbps,
0021 0041 0024 0035 0036 0025 0031 0034 0024 0018 latest value first
LONG INTERVAL VIOLATION
Reason for message - here: the limit for the 60-

second (LONG) interval was undershot
Expressed in Kbps
the value set with the parameter MINTHRPT and SHORT is 2/3 of LONG. Expressed in Kbps.

3s 6s 9 s 12 s 15 s 18 s 21 s 24 s 27 s 30 s
33 s 36 s 39 s 42 s 45 s 48 s 51 s 54 s 57 s 60 s
63 s 66 s 69 s 72 s 75 s 78 s 81 s 84 s 87 s 90 s
2.7.6.4 F8291 - Net Weakness End
F8291 M4 N0380 NO ACT BPA TRANSSYS NET WEAKNESS END 04-06-07

13:04:05
FORMAT:49
AP NUMBER: 99
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.7.6.5 F8292 - Bandwidth Requirement Exceeds Limit
F8292 M4 N0284 NO ACT BPA TRANSSYS NET BW EXC BEGIN 04-06-07

12:41:13
ALARM CLASS:CENTRAL:005 Configured bandwidth to be set as limit
FORMAT:49 Expressed in Kbps
AP NUMBER: 99
LIMIT = 0064 KBIT/S
SHAPING TIME = 0011 Time (in seconds) during which the number of
messages to be sent exceeded the number permitted
by the limited bandwidth
2.7.6.6 F8293 - Bandwidth Required Back Below Limit
F8293 M4 N0366 NO ACT BPA TRANSSYS NET BW EXC END 04-06-07

12:49:45
FORMAT:49
AP NUMBER: 99
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Source Dependent Routing
2.8 Source Dependent Routing

With IP distributed architecture, it is possible to position parts of a HiPath 4000
system in different local networks. In this way, the HiPath 4000 CC could be
located in Munich, with linked access points in Berlin and Frankfurt.
Now, if all calls were to be subject to uniform routing, this would result in a call
from the Frankfurt access point being routed into the Frankfurt local network - with
LCR from the point of view of the CC in Munich - via IP to Munich and from there
back to Frankfurt as a long-distance call. This would not be particularly cost-
effective.
If a subscriber at the access point in Berlin were to call the fire service, the call
would arrive at the fire service in Munich, which would not only be prohibited, but
also dangerous.
The solution to this problem is to assign the access points in Berlin and Frankfurt
a connection to the respective local network and to route them on a subscriber-
dependent basis.
This “source dependency“ always applies to multiple subscriber lines, CO circuits

or tie trunk circuits. In order to identify a group requiring the same routing
behavior, the source group ID is introduced. Every access point must be assigned
to a source group. If the subscriber line, CO or tie trunk circuits are configured
with source group ID “0“ (default value), they adopt the settings of the access
point. If necessary, a source group ID which deviates from the access point can
be assigned to individual subscriber lines, CO circuits or tie trunk circuits.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Berlin
030-386
AP 99
HG
STMI-1 STMI-2
Peripheral
HG Source Group 2 3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
AP 98
3500 HG Peripheral

3575 Boards
IP Network
AP 3300 IP, AP 3500/3505
Peripheral
Munich
Boards 089-722
Source Group 1 Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP
Frankfurt
AP 18
HG 069-767
Peripheral
3575 Boards
Source Group 3
CC-A R1
Router AP 3300 IP, AP 3500/3505
P S T N N e t wo r k
AP 17
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assis
tant
HiPath
4000
Figure 24 Source-dependent routing
In the example, access points AP 17 and AP 18 in Munich have been assigned

to Source Group 1, which is also always the default setting for all LTUs (1..15) of
the central HiPath 4000 system. The two access points in Berlin (AP 98 and AP
99) have been assigned to Source Group 2. The Frankfurt access point AP 43
has Source Group 3.
The number of the source group is specified as the source group index with ADD-
UCSU (see parameter SRCGRP in Table 6 “APNW: AMO UCSU parameters in
ADD branch under TYPE=AP”).
In order to realize source dependent routing, LCR had to be extended.
While routing numbers (LROUTE) have previously been assigned in the digit
pattern plan with the AMO LDPLN for one digit pattern, taking into account DPLN
groups, class of service etc., source dependent routing requires that the index of
an LCR profile (PROFIDX) be specified instead of the LROUTE. In the LCR
profile, an LROUTE can be branched to as a function of the source group index.
LCR profiles are configured with the AMO LPROF.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
LDPLN LDPLN LPROF

... ... ...
Digit pattern LDP Digit pattern LDP 1 LRTE
0 LROUTE 0 PROFIDX 2 LRTE
1 LROUTE 1 PROFIDX 3 LRTE
2 LROUTE 2 PROFIDX LRTE
Index [1.. 99]

Source group
LRTE PROFIDX LRTE
DPLN groups
DPLN groups
[0 .. 15]
[0 .. 15]
LROUTE PROFIDX LRTE
LROUTE PROFIDX LRTE
LROUTE PROFIDX 1 LRTE
... ... 2 LRTE
3 LRTE
LRTE
Index [1 .. 99]
Source group
LCR LRTE
with LRTE
“Traditional“ LCR Source-dependent routing
LRTE
...
Figure 25 Interaction between LDPLN and LPROF
As PROFIDX indicates an LCR profile in the digit pattern plan, this must be
configured first.
An LCR profile for emergency calls to the fire service is to be generated. In

Munich, LRTE 722 leads to the CO; in Berlin, LRTE 386 and in Frankfurt, LRTE
767.
Configuration Management --> Least Cost Routing --> LCR Profiles

Click New, enter the Profile Name, Source Group, and LCR Route and
Save.
The profile index is calculated and returned.
ADD-LPROF:PROFNAME=FEUERWEHR,SRCGRP=1,LRTE=722;
The AMO returns the profile index, provided it is 12.

Additional source groups can be supplemented with:
CHANGE-LPROF:PROFIDX=12,SRCGRP=2,LRTE=386;
CHANGE-LPROF:PROFIDX=12,SRCGRP=3,LRTE=767;
Next, an entry can be made in the digit pattern plan for emergency calls to the fire
service, indicating the LCR profile number 12 just configured.
Configuration Management --> Least Cost Routing --> Digit Pattern

Click New, enter 112 for Digit Pattern. On the Data tab, enter the LCR
Profile Number configured above under profile index and SAVE.
ADD-LDPLN:LDP=112,PROFIDX=12, ...;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Additional functions of the AMO LPROF:
DELETE-LPROF:PROFIDX=12,SRCGRP=3;
Deletes the entry for a source group from the specified LCR profile. If no source
group is specified, the entire profile is deleted.
DISPLAY-LPROF:PROFIDX=1&&33,INFOPAT=FEUER,FORMAT=K;
All parameters are optional. A specific index or range can be specified for
PROFIDX. INFOPAT allows a search pattern to be specified. If the pattern is
found in a profile name, the profile is output. FORMAT is used to choose between
short or long output format.
Notes:
• Every subscriber line, CO circuit or tie trunk circuit is automatically assigned
the source group index 0 upon configuration. This means that the LTU source
group index is used. However, it can be changed individually. A maximum of
99 source groups are available.
• The source group index used for a subscriber is output when the AMO SDAT
is called up.
The output SRCGRP =(1)means that the subscriber uses the LTU source
group index. The subscriber is configured with SRCGRP=0.
If the subscriber moves in an LTU that is assigned to another source group, it
is assigned this source group.
• The output SRCGRP = 1 means that the subscriber uses the value 1
independent of the LTU source group index. The subscriber is configured with
SRCGRP=1.
The user-specific source group that is set thus remains the same if the
subscriber moves to another LTU. Check if this allocation is still useful.

Language
LPROF FORMAT d Abhängig vom Parameter Format werden die
Profile in einem gekürzten Format angezeigt (nur
die Service Information) oder in einem langen
Format (alle für LCR Profile relevanten
Informationen)
K Ausgabe LCR Profile, Service Information - Kurz
L Ausgabe LCR Profile Einträge - Lang.
Table 17 AMO LPROF parameters
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
FORMAT e According to the parameter format, the profiles are
displayed in a short format (only the Service
Information) or a long format (all LCR profile
releated info).
S Display LCR Profile, Service information - Short
L Display of LCR Profile related info - Long
INFOMUS d Bestimmt das Muster nach dem das Profil
angezeigt wird. Wenn das im Parameter INFOMUS
angegebene Muster im Profil Namen gefunden
wird, wird das folgende Profil angezeigt.
INFOPAT e Specifies the pattern according to which profiles will
be displayed.If the pattern given in the INFOPAT
parameter is found in the profile name, the following
profile is displayed.
LRTG d LCR Richtung
LRTE e LCR route
PROFIDX d LCR Profil-Index
PROFIDX e LCR profile index
PROFNAM d LCR Profilname
E
PROFNAM e LCR profile name
E
Table 17 AMO LPROF parameters
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Payload Survivability
2.9 Payload Survivability

In principle, the IP distributed architecture is dependent on the availability of the
IP network. If the IP connection fails between two access points or between the
central HiPath 4000 switch and an access point, no payload connections are
possible via IP.
Also, separation of signaling and payload streams is required very often by

customers in the following scenario:
• signaling from branch to HQ should go over the IP Customer Network (WAN)
• payload should go over the traditional PSTN network using ISDN flatrate
The aspect of signaling between the CO and the access point is covered in
Signaling Survivability.
If control of the access point is safeguarded through signaling survivability, calls

can be made within the access point in all cases. External calls via trunks or tie
trunks in other systems are possible if the corresponding connection modules are
located in this access point.
Payload survivability uses existing trunks in order to establish payload

connections with other access points or with the HiPath 4000 central system
independently of the IP network. In this context, the system calls itself via the
trunk.
The procedure followed for payload survivability between a local subscriber and
a CO/tie trunk circuit is route-specific.
If the call comes in via the CO/tie trunk circuit, a trunk call is established between
the source group into which the call comes and the source group to which the
subscriber belongs.
If, on the other hand, the HiPath 4000 subscriber establishes the call, the call is
routed out of the system via the CO using LCR. A CO/tie trunk from the central
system cannot be used in this case.
Payload survivability is destination-oriented and is restricted to one HiPath 4000

system. If other systems are connected to the HiPath 4000, the networking LCR
must be extended. Details can be found in Section 2.9.3, “Payload Survivability
in HiPath 4000 Networks”.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.9.1 When is Payload Survivability Used?

There are the following reasons to handle connections to access points via trunk
traffic instead of via IP:
a) If the quality of the existing connections in the IP network is bad
b) The capacity of the IP link is exhausted
c) If a subscriber specifies via access code that he does not wish to use IP
d) Payload Survivability when signaling survivability is active
e) If in AMO UCSU parameter BCHLCNT is set to „0“.
If the quality of the existing connections in the IP network is bad

The quality of the active payload connections via the IP network is permanently
monitored.
If the packet delay or the packet loss rate exceeds the predefined or upper limits,
the connection is labeled as „Bad Quality“. If these variables drop below the
likewise predefined lower limits, the connection is relabeled as „Good Quality“.
The limit values are set in the PLQUAL branch in AMO SIPCO (see Section 2.1,
“Payload Quality (PLQUAL)”).
Figure 26 “Blocks the IP connection for payload due to „Bad Quality“” indicates
the sequences:
PINGTIME
Payload (1 connection)
2 6
(AP43 -> AP 99)
Bad Quality Indicator

3 4 5 7 8
1 (AP43 -> AP 99)
Figure 26 Blocks the IP connection for payload due to „Bad Quality“
At the start of appraisal, the IP connection quality of AP 43 to AP 99 is labeled as

1 good.
A payload connection is established via IP.

2
The constant monitoring of the connection quality reports “Bad Quality“

3
From this time on, no further payload connections are established between AP 43
and AP 99 via IP. If available, an alternative route via payload survivability is used.
Otherwise, the connection request is rejected.
The existing payload connection is not disconnected, despite “Bad Quality“.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
The constant monitoring of the connection quality reports a return to “Good Quality“
4 The establishment of payload connections between AP 43 and AP 99 over IP
resumes from this time on.
as per 3
5
The subscriber terminates the payload connection

6 At this time, the connection is labeled as “Bad Quality“.
As a result of the preceding payload connection, “UDP ping“ messages are now
transmitted every 5 seconds, in order to further monitor the behavior of the IP
connection.
The test with “UDP ping“ messages shows that the connection quality has been
7 restored.
The “Bad Quality indicator“ is reset.
From this time on, payload connections are again established between AP 43 and
AP 99 via IP.
If the tests with “UDP ping“ messages are unsuccessful, the “bad quality indicator“
8 is reset after expiry of PINGTIME.
PINGTIME is configured in the TIMING branch of the AMO SIPCO. The value range
is between 0 and 3600 seconds.
Important
• It is recommended to change the parameter PINGTIME in AMO SIPCO from

the default value 60 to the maximum value of 3600.
• The actual status of the Payload Matrix can be displayed from AMO SIPCO with
the command DIS-SIPCO:PLMATRIX;
• Additionally to help follow the status of the Payload Matrix, the following F5915/
F5750 error messages can also be activated by aid of a DIAGS switch CHA-
DIAGS:,NMC,,ON;
REASON:01H IP GOOD QUALITY
REASON:02H IP QUALITY TEST TIMER EXPIRED
If several payload connections are running in parallel between 2 access points or

between an access point and HG 3500, these may provide differing quality
statements. In all events, the „Bad Quality“ status of a connection is always
prioritized over any number of „Good Quality“ connections.
In other words, if 10 connections report „Good Quality“ and 1 reports „Bad

Quality“, no further IP connections are established until the connection with the
status of „Bad Quality“ has returned to a status of „Good Quality“. For information
on possible sequences, see Figure 26 “Blocks the IP connection for payload due
to „Bad Quality“”.
All payload routes between the central system (all HG 3500 modules) and an
access point are labeled „Bad Quality“ as soon as signaling survivability is
activated for the access point. In this case it is assumed that a fault affecting the
route between the central system and access point is having the same effect on
the payload connections.
If the blocking of the availability of subscriber lines in an access point without

payload survivability due to poor IP connections is to be prevented („Bad
Quality“), payload quality handling can be deactivated for the access point in the
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
AMO UCSU with the parameter PLCHECK. This means that every call is
switched regardless of the quality of the IP connection. In the worst case
scenario, this can result in the call being signaled, but the voice link remaining
dead because no packets with payload are received.
The capacity of the IP link is exhausted

The transport capacity for payload connections between an access point and the
IP network is limited by the maximum number of simultaneous connections
possible (30/60/120 connections depending on the hardware) and the maximum
bandwidth configured in the Resource Manager. If the full transport capacity is
used, the payload survivability route is automatically used for further calls within
the HiPath 4000 system. The path selection makes no distinction as to whether
there is no path available because of a failure in the IP network or because all
available routes from the access point are already occupied.
Because of the restrictions with regard to payload survivability, the system must
be configured so that this spillover route is only used in cases of exceptional
overload.
If a subscriber specifies via access code that he does not wish to use IP
In HiPath 4000 system, the WABE code FRCALTRT can be used to force the
survivability route. The access code FRCALTRT can be used by anyone and is
not subject to any class of service requirements. The same payload survivability
restrictions apply for these calls.
Payload Survivability when signaling survivability is active

If a HiPath 4000 Softgate is in signaling survivability mode, then the connections
to all other APs which are in a different source group than the designated HiPath
4000 Softgate, will be estabilsehd over the alternative route.
Connection to all APs which share the same source group with the designated
HiPath 4000 Softgate will be established over LAN if possible. If this is not
possible, then no connection is possible.
As for IPDA traditional shelves, the functionality is controlled by the parameter

NPLMSURV in AMO Zande > ALLDATA. If this parameter is set to NO then we
have the same functionality as in versions prior to HiPath 4000 V5.
If NPLMSURV is set to YES then the traditional IPDA shelves will have an
enhanced behavior similar to the HiPath 4000 Softgate behavior mentioned
above.
I.e. an IPDA shelf in sigalling survivability mode will connect to HiPath Host
System. All other APs which are in a different source groups will connect over the
alternative route.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
On the other hand connection to all APs which share the same source group with
the designated HiPath 4000 Softgate will be established over LAN if possible, and
if not, then no connection is possible.
IMPORTANT: Parameter NPLMSURV has no effect on a HiPath 4000 Softgate

which is in Signaling Survivability mode. HiPath 4000 SoftGate always follow the
enhanced behavior.
IMPORTANT: Parameter PLMSGSRV in AMO Zande > ALLDATA has no effect.
functionality as in versions prior to HiPath 4000 V5

All payload routes between the host system (all HG 3500 modules) and an
access point are labeled as „Bad Quality“ as soon as signaling survivability is
activated for the access point.
IMPORTANT: In case of alternative routing (signaling surviability is active) the

payload matrix between HHS and the corresponding AP will be blocked. All
available routes from HHS to AP are marked as BAD IP.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.9.2 How is Payload Survivability Configured?
2.9.2.1 Overview
Berlin
030-386
AP 99
HG
STMI-1 STMI-2
Peripheral
HG Source Group 2 3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
AP 98
3500 HG Peripheral
3575 Boards
IP Network
AP 3300 IP, AP 3500/3505
Peripheral
Munich
Boards 089-722
Source Group 1 Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP
Frankfurt
AP 18
HG 069-767
Peripheral
3575 Boards
Source Group 3
CC-A R1
Router AP 3300 IP, AP 3500/3505
P S T N N e t wo r k
AP 17
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assis
tant
HiPath
4000
Figure 27 Payload survivability - source dependent routing configuration
Payload survivability requires CO lines at access points, in order to switch

alternative routes. If, in example Figure 27 “Payload survivability - source
dependent routing configuration”, the IP connection between Berlin and Frankfurt
fails, all existing calls will be interrupted. No new calls can be set up until “Good
Quality“ has been determined again.
As both an access point in Berlin and the access point in Frankfurt have a local
CO line, calls between subscribers in Berlin and Frankfurt can alternatively be
switched via the trunk. Of particular note here is that, in the case of IPDA, a
HiPath 4000 system now calls itself via trunk, in order to connect its own
subscribers.
The alternative routes are defined as a function of the source group. Thus, in the
example, it is unnecessary for AP 99 to have its own trunk access. It can be
reached via the trunk access of its source group in AP 98.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.9.2.2 Variants of Payload Survivability
There are 3 variants of payload survivability, which depend on the type of trunk
switching and have different advantages and disadvantages. ALR should be used
as standard.
ALR with single Functions with any kind of trunk switching, even analog.
number
• A separate phone number must be assigned to each channel of
the trunk switching
• Therefore requires many individual phone numbers and many

entries in the ALTROUT table
• When the payload survivability route is used, party A sees the

“Alternate Routing Number“ used for the call in addition to the
dialed internal number
• When the payload survivability route is used, party B hears the

“external call ring“ despite the fact that it is an internal call, but
sees the internal phone number of party A.
ALR via Only functions with multichannel ISDN CO lines.
multichannel
trunk circuit • Only one phone number for all of the channels of a circuit
under one call • Only one entry per circuit in the ALTROUT table
number
• Use of the “Artificial Calling Number“ requires agreement with
the PSTN network carrier that the transmitted calling party
number will not be checked, as it does not correspond to the
actual phone number for the circuit (USER PROVIDED
SCREENED). The same must be agreed for all source groups.
The source group for which ALR is configured with ARTCNR
must be available in this way from all other source groups.
• The entire carrier network must guarantee transmission of the

Artificial Calling Number from all source groups without
corruption. (No modification of the phone number)
• Call charges for using the payload survivability route cannot be

uniquely assigned to the calling party
• When the payload survivability route is used, party A sees the

“Alternate Routing Number“ used for the call in addition to the
dialed internal number
• When the payload survivability route is used, party B hears the

“external call ring“ despite the fact that it is an internal call, but
sees the internal phone number of party A.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
PUBDID If PUBDID numbers are already configured for subscribers of an

access point, these can also be used for payload survivability.
• Relatively high level of administration effort involved, as the

PUBDID number has to be configured individually for each
subscriber.
• 1 entry in the ALTROUT table for the entire source group
• The PUBDID number is retained in the event of a relocation
• In the case of payload survivability, the PUBDID number is

displayed for the other party
• Call charges for using the payload survivability route can be

uniquely assigned to the calling party
ALR with single number

At the CO line which is (also) to be used for the payload survivability of a source
group, certain call numbers are configured for payload survivability.
Let us assume that the numbers 069-767-97, 069-767-98 and 069-767-99 have
been reserved in Frankfurt for payload survivability. Up to 3 calls can then reach
source group 3 simultaneously via alternative routes.
The INCALTRT digit analysis result must be configured in WABE for every access
code.
This is configured through
Configuration Management --> System Data --> IPDA --> IPDA Payload
Survivability
Click New, enter Index, Routing Position, Phone Number and Access
Code on the Basic Data tab and Save.
Configuration Management --> Tables --> Dial Plan --> Dial Codes
Click New, select Delete Mask on the Edit pull-down menu.
Enter the Dial Code and Code Type and Save.
ADD-APRT:TYPE=ALTROUT,SRCGRP=3,POS=1,ALRTYPE=ALR,
ALTRTNR=006976797,ACCODE=97;
ADD-WABE:CD=97,DAR=INCALTRT;
This insertion sequence means that ACCODE 97 is at the top of the
list and is occupied first.
Note regarding ALTRTNR

Specific rules must be observed for the Alternate Routing Number ALTRTNR:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• ALTRTNR must contain the access code for CO breakout.
• If the source groups are distributed across different local networks, the local
network access codes must also be specified (see example).
• The access code setting for CO breakout must be identical in all source
groups. The destination number must be accessible in the same way from all
other source groups.
• ALTRTNR cannot be modified throughout the entire network with LCR (no
REROUTE-INTERN).
• ALTRTNR must be routed in each source group on a “source-dependent“

basis.
Note regarding AMO parameter POS (AMO APRT:ALTROUT)

The AMO parameter POS is optional. If this parameter is not specified, the entry
is inserted at the end. The table is always kept compact starting at POS=1. If a
specific POS value is specified, the table entry is only entered at this position if
this position is already occupied or if it is the first free position. If this position is
not free, the entries following POS are shifted back. If this position is not free, the
entries following POS are shifted back. 
If an entry is deleted, all subsequent entries are shifted forwarded by one position.
POS is important when multiple entries are made for a source group. Assignment
of the specified alternative routes is in ascending order according to the POS
value.
ALR via multichannel trunk circuit under one call number

At the CO line, 30 channels are available, for example, to a source group for
payload survivability, all of which can be reached via the same call number. In
Munich, for example, this could be the number 089-722-9000.
The INCALTRT digit analysis result must be configured in WABE for the access
code 9000.
Furthermore, up to 30 calls, for example, can reach source group 1

simultaneously via alternative routes. However, as all calls are routed to the same
call number (ACCODE, AMO APRT:ALTROUT), the call processing is faced with
the problem of correctly assigning the alternative route calls. To this end, an
identification number has to be transmitted with each call. This is realized by
replacing the Calling Party Number. Precisely which numbers will be available to
this end is configured via the parameters ARTCNR (Artificial Calling Number) and
ARTCNRG (Artificial Calling Number Range).
The Artificial Calling Number is configured on a target-dependent basis with the

information on a specific source group. However, this number is used at the
source, i.e. at the trunk access which leads into the alternative route. The value
is ultimately used as the Calling Party Number. As carriers do not allow freely
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
selectable Calling Party Numbers, an agreement must be made with the carrier
concerning the use of the Artificial Calling Numbers). The carrier must deactivate
checking of the Calling Party Number (CLIPNOSCREEN).
Configuration example:
Survivability
Click New, fill in all fields for alternative routing on the Basic Data tab and
Save.
Configuration Management --> Tables --> Dial Plan --> Dial Codes
Click New, select Delete Mask on the Edit pull-down menu. Enter the Dial
Code and Code Type and Save.
ADD-APRT:TYPE=ALTROUT,SRCGRP=1,ALRTYPE=ALR,
ALTRTNR=00897229000,ACCODE=9000,ARTCNR=1000,
ARTCNRNG=30;
Note regarding ARTCNR

Specific rules must be observed for the Artificial Calling Number ARTCNR:
• The ARTCNR ranges for different circuits and source groups must not
overlap.
• The ranges must be big enough to allow the desired maximum number of
calls via the payload survivability route on a circuit.
• This ARTCNR range must NOT be reserved in WABE.
• The entire carrier network must guarantee transmission of the ARTCNR

range from all source groups without corruption. (No modification of the
phone number)
PUBDID
Subscribers of a source group have a Public DID number in the local CO. In other
words, Berlin-based subscribers can be reached directly both via the central
HiPath 4000 switch’s Munich dial-in and via their Berlin dial-in number. For
example: a subscriber could be reached not only via 089-722-12345, but also via
030-386-789 (different extension numbers/branch concept.
Setting the PUBDID number: [TON: Type Of Number - NPI: Numbering Plan
Identifier]

Click Search and go to subscriber. Enter the Sation No., Numbering Plan
Identifier and Type of Number (TON) on the Basic 3 tab under Primary
Rate Interface and Save.
CHANGE-SDAT:STNO=12345,TYPE=DATA1,PUBNUM=30386789,
TON=NATIONAL,NPI=ISDN;
Other settings made using the AMOs DNIT and DIDCR are required.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
If this mechanism for payload survivability is to be used, it is activated as follows:
Survivability
Click New, enter the Position and Type Of Routing on the Basic Data tab
and Save.
ADD-APRT:TYPE=ALTROUT,SRCGRP=2,POS=1,ALRTYPE=PUBDID;
However, it is also possible to configure one of the ALR procedures for payload
survivability for source groups.

Language
APRT SRCGRP d Source Group Index
Group. Die Access Points einer Source Group sind
für Payload Survivability über einen bestimmten
Amtsanschluss erreichbar.
Assignment of the Access Point to a Source Group.
The Access Points of one Source Group are
reachable via a distinct CO trunk for Payload
Survivability.
POS d Position
Index des Eintrags in der Alternate Routing Tabelle.
[1 .. 500]
Siehe auch: Section 2.9.2.2, “Note regarding AMO
parameter POS (AMO APRT:ALTROUT)”
POS e Position
Index of the entry in the Alternate Routing Table. [1
.. 500]
See also: Section 2.9.2.2, “Note regarding AMO
parameter POS (AMO APRT:ALTROUT)”
ALRTYP d Alternate Routing Typ des Eintrags.
3 Typen sind möglich:
ALR: Alternate Routing über eine DID, DIT oder
PRI Nummer.
NOALR: Kein Alternate Routing Pfad
PUBDID: Alternate Routing über Public DID
Nummer, d.h. Teilnehmer haben eine zweite
Nummer, unter der sie über den Amtsanschluss für
die angegebene Source Group aus dem
öffentlichen Netz erreichbar sind.
Table 18 AMO APRT parameters in ADD branch under TYPE=ALTROUT
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
ALRTYPE e Alternate Routing Type of the Entry
3 types are possible:
ALR: Alternate Routing via a DID, DIT or PRI
number.
NOALR: No Alternate Routing
PUBDID: Alternate Routing using a public DID
number. Subscribers are reachable by a second
number via the CO access for the specified Source
Group.
ALTRTNR d Rufnummer für Alternate Routing
Vollständige Rufnummer des Alternate Routing
Anschlusses
Siehe auch: Section 2.9.2.2, “Note regarding
ALTRTNR”
ALTRTNR e Alternate Routing Number.
Complete number of the Alternate Routing access
See also: Section 2.9.2.2, “Note regarding
ALTRTNR”
ACCODE d Access Code
Nebenstellennummer des Alternate Routing
Anschlusses, d.h. ALTRTNR ohne Vorwahl und
Amtsnummer. Maximal 6-stellig.
ACCODE e Access Code
Extension Number of the ALternate Routing
Access.
ALTRTNR without Area and Office Code. Maximum
6 digits.
ARTCNR d Artificial Calling Number
Maximal 6-stellige Nummer, welche zur
Identifikation des Rufes als “Nummer des
Rufenden” übertragen wird.
Diese Nummer ist die erste eines Bereichs (siehe
ARTCNRNG), der für diese Zwecke genutzt wird.
Siehe auch: Section 2.9.2.2, “Note regarding
ARTCNR”
ARTCNR e Artificial Calling Number.
A number with a maximum of 6 digits. Is given als
“Calling Party Number” to identify the call.
This number is the first of a range (see
ARTCNRNG) used for that purpose.
See also: Section 2.9.2.2, “Note regarding
ARTCNR”
ARTCNRNG d Artificial Calling Number Bereich
Gibt an, wieviele Artificial Calling Numbers
einschließlich ARTCNR zur Verfügung stehen [1 ..
99999].
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
ARTCNRNG e Artificial Calling Number Range
Specifies, how many Artificial Calling Numbers
including ARTCNR are available [1 .. 99999].
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.9.3 Payload Survivability in HiPath 4000 Networks

Payload survivability is destination-oriented and is restricted to one HiPath 4000
system. If other systems are connected to the HiPath 4000 via ECMAV2 trunks
(closed numbering), the networking LCR (NWLCR) must be extended.
Otherwise, AP subscribers cannot access the relevant network subscribers when
payload survivability is active.
The procedure followed for payload survivability between a local subscriber and
a CO/tie trunk circuit is route-specific.
If the call comes in via the CO/tie trunk circuit, a trunk call is established between
the source group into which the call comes and the source group to which the
subscriber belongs.
If, on the other hand, the HiPath 4000 subscriber establishes the call, the call is
routed out of the system via the CO using LCR. A tie trunk from the central system
cannot be used in this case.
Figure 28 “Payload survivability and networking - normal route A calls B or B calls

A”, Figure 29 “Payload survivability and networking - survivability route A calls B”
and Figure 30 “Payload survivability and networking - survivability route B calls
A” show the different routes.
To handle call A -> B with payload survivability (Figure 29 “Payload survivability

and networking - survivability route A calls B”), an extension must be added to the
NWLCR of system 1 for the route to DESTNO 2. This extension contains an
overflow entry to the local CO of AP 17 (trunk group 17), which ensures that
routing to destination system 2 takes place via CO in the case of payload
survivability.
22710
AP 17
System 1
Trunk group 17 +49 (89) 722-X
A P S T N N e t wo r k
+49 (69) 7200-X +49 (69) 6400-X
HiPath 4000 HiPath 4000

System 1 System 2
IP Network B
ECMAV2 tie trunk
Trunk group 24
24000
Sub. 22000-23999 Sub. 24000-24999

DESTNO 1 DESTNO 2
Figure 28 Payload survivability and networking - normal route A calls B or B

calls A
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
22710
AP 17
System 1
Trunk group+49
17 (89) 722-X
A P S T N N e t wo r k
+49 (69) 7200-X +49 (69) 6400-X

System 1 System 2
IP Network B
ECMAV2 tie trunk
Trunk group 24
24000
Sub. 22000-23999 Sub. 24000-24999

DESTNO 1 DESTNO 2
Figure 29 Payload survivability and networking - survivability route A calls B
22710
AP 17
System 1
Trunk group+49
17 (89) 722-X
A P S T N N e tw or k
+49 (69) 7200-X +49 (69) 6400-X

System 1 System 2
IP Network B
ECMAV2 tie trunk
Trunk group 24
24000
Sub. 22000-23999 Sub. 24000-24999

DESTNO 1 DESTNO 2
Figure 30 Payload survivability and networking - survivability route B calls A
NWLCR extension for AP 17 to system 2 with payload survivability (Figure

29 “Payload survivability and networking - survivability route A calls B”)
+--------------------------------------------------------------------------+
| LRTE = 124 NAME = SYSTEM 2 SERVICE = ALL |
| TYPE = NWLCR DIDNO-ROUTE = 1 -2 -400 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
|LRTGEL |LVAL |TRUNO| LWR| LBER | ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 24| 1| 1 | ******** | 1 EMPTY | NONE | |
| 2 | 1| 17| 17| 17| |******** | 1 EMPTY | NONE | |
+-------+-----+-----+-----+------+----------+------------+----------+------+
+-------------------------------------------------------+
| LWR LWRELPOS LWREL PARAMETER |
+--------+----------------------------------------------+
| 1 | 1 ECHO 1 |
| | 2 END |
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
+--------+----------------------------------------------+
|INFO:STANDARD NWLCR FOR SYSTEM 2 |
+-------------------------------------------------------+
+-------------------------------------------------------+
| LWR LWRELPOS LWREL PARAMETER |
+--------+----------------------------------------------+
| 17 | 1 OUTPULSE 696400 |
| 2 | 1 ECHO 1 |
| | 3 NPI ISDN |
| | 4 TON NATIONAL |
| | 5 END |
+--------+----------------------------------------------+
|INFO:OVERFLOW CO FOR SYSTEM 2 (SURVIVABILITY) |
+--------+----------------------------------------------+
2.9.4 Restrictions
Display problems on VNR systems when Payload Survivability is activated
Please note that in case of a VNR system, for calls that have to be sent over the
payload survivability route, the displayed called numbers will change to the
numbers used for the external routing via the public network.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.10 Signaling and Payload Separation (SPS)
IMPORTANT: Signaling and Payload Separation (SPS) is released for stand-

alone systems only! In networked environment a project specific release (PSR) is
required and only basic call is possible!
Signaling and payload separation is a feature which enables HiPath 4000 in an

IPDA environment to split the path of the network traffic in the meaning of
– signaling from Hostsystem (call control) to access point is routed over the
IP Customer Network (Enterprise WAN)
– payload is routed over the PSTN Network using payload survivability

connections (e.g. calls from host system to an access point is
automatically routed via CO).
IMPORTANT: SPS connectivity and features are only supported for IP Access
Points and host shelves (LTUs) that are controlled by the central communication
server (host system). If an IP Access Point goes in AP Emergency survivability
mode, then SPS connectivity and features are no longer possible/supported. For
IP Access Points in AP Emergency mode all calls to other IP Access Points and
host shelves will be routed over PSTN based on the AP Emergency LCR routing
configuration with basic call functionality.
Signaling and payload separation based on existing survivability solution and

therefore the signaling path is routed in the same way as today.
Signaling and payload separation can be configured in a way that
– payload separation is always active (static signaling and payload

separation)
– payload separation is used in case of limited WAN- bandwidth managed

by the resource manager or overflow scenarios when then maximum of
bandwidth is reached (payload overflow)
– payload separation is used in case of network failure (emergency routing)
– If a subscriber specifies via access code that he does not wish to use IP.
In this case payload separation with all access points configured in
different source groups can be used
In this situation all access points have to be assigned in different source
groups and CO access will be mandatory for all access points.
All calls between access points and between access points and host
system will be made over ISDN lines.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.10.1 Features and their Restrictions

• Basic call
– Direct calls from one shelf to another will be routed through central office
(e.g. calls from the host system to an access point will be automatically
routed via the CO).
– Name and number display: Incoming and outgoing calls - When the
payload survivability route is used:
– The calling party will see for basic call the called number and name
on the first line.
– The called party will see for basic call the calling number and name
on the first display line.
– When the payload survivability route is used, called party hears the
"external call ring" despite the fact that it is an internal call.
– If CO connection will breakdown during a call between different shelfs, the

call will have no payload and will be disconnected after 90s.
– The name is not shown on TIE calls.
IMPORTANT: Signaling and Payload Separation (SPS) is released for

standalone systems only! In networked environment a project specific release
(PSR) is required and only basic call is possible!
• Hunt Group
– Hunt group specific functionality is covered - linear/cyclic, master/pilot,

activate/deactivate hunt, overflow.
– Hunt group memebers must be located on the same branch.
– Hunting group stations are reached over LAN if calling party and hunt
group member are in the same shelf. In case that calling party and hunt
group member are in a different shelf hunting group station is reached
over Central Office.
– Charging:
The calling party will be charged if a hunting group station that is located
on a different shelf will answer. For external (CO) calls the paying party is
a default virtual route code destination and the destination is the ALR
number.
– Incoming calls to hunt group - When the payload survivability route is

used:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
– The calling party will see the name and number of the hunting group
on the first line and the alerting hunt group member number and name
on second the line.
– The connected party will see the hunt group member number and
name on the first line.
– The alerting hunt group member will seethe calling number and name
on the first display line and the name and number of the hunting group
on the second line of the display.
– The connected hunt group member will see the connected number
and name on the first display line.
Overflow scenario:
– The calling party will see the name and number of the hunting group on
the first line and the last alerting hunt group member name and number
on the second line.
– The connected party will see the hunt group member number and name
on the first line.
– Forwarding for hunt group members is not supported (LVAFTEXT =N)*
– Announcement with hunting group call queue is not supported due CO

resource limitations.
– Execute call forwarding from hunt group parameter EXECCFW will be

ignored if the calling party and hunting group station with activated call
forward are located on different shelves.
• Call Pick Up
– Pick up specific functionality is covered (display of the calling user

(DISTNO), delayed notification ring (NOTRNG).
– Call pick up members must be located on the same branch.
– A station/user can pick up calls which belong to the pickup group.

For call scenarios where the calling party is located on a different shelf
than the called and picking party the CO route will be used. The calling
party will be charged.
For external (CO) calls the paying party is a default virtual route code
destination and the destination is the ALR number.
– Display
The picking party will see on the display the name and number of the
calling partner.
– When the payload survivability route is used, the called party hears the
"external call ring" despite the fact that it is an internal call.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
– Directed call pickup is not supported.
– Networkwide call pickup groups are not supported.
• Call Back
A station user can set a call back request to a party located on a different
shelf.
– Callback busy/no answer/free/mailbox is possible for calls between

different branches over CO.
– When callback is initiated (called party become free), calling party hears
the "internal call ring" despite the fact that it is an internal call.
– When callback is executed, called party hears the "external call ring"
despite the fact that it is an internal call.
– Callback from/to network partner is not possible - "Callback" menu will not
be offered .
• Call Forwarding
The user can forward calls to a party located on a different shelf.
– Call forwarding busy/no answer is possible in the same system. To

stations located on different branches the call will be routed over CO.
– Call forwarding to Xpressions is possible independent of shelf location

when a TIE trunk to Xpressions is configured.
– For Call forward scenarios no CO resources will be used if the calling

party and forward destination station are located on the same shelf.
– Charging
The calling party will be charged if the forward destination is located on a
different branch.
– Display
Forward Unconditional/Busy - The forward destination is located on a
different branch than the calling party
– The calling party will see the called name and number on the first line
display.
– Diverted-to party will see the calling party name and number on the
first line.
Forward no reply - If forward destination is located on a different branch
than the calling party:
– The calling party will see the called name and number on the first line
display and diverted-to party name and number on the second line
display.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
– Diverted-to party will see the calling party name and number on the
first line.
– Call forwarding indication at diverted-to party is not shown on the display.
• Transfer and Toggle
– The user can transfer calls to a party located on a different shelf.

Transfer of incoming and outgoing external calls is possible to stations
located on a different shelf. In this case the call will be routed over CO.
– Display
The calling party will see after transfer the called party name and number
and the transfered to party will see the calling party name and number on
the first line display.
– Ring
If the calling party and transferring party are located on different shelves
the transferred party hears the "external call ring" independent of the
location of the transferred party (local, network).
• Conference
– The user can initiate a conference or be a conference member.
– Display
If all members of a conference are located on the same branch as the
conference master the display will show the correct information.
– The memebers of a conference which are located in another branch as

the conference master will see on the display only one connection to the
conference master.
– ALR route name will be shown instead of party name for members of a
conference which are located in another branch as the conference
master.
• Keyset
– All Keysets can be reached via the main station number and can initiate
calls using primary line.
– Primary, Secondary and phantom line must be located in the same source
group.
• Name and number display
• One Number Service (ONS)
– An ONS member can pick up calls which belong to the ONS group.
– ONS group members must be located on the same branch.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
– For call scenarios where the calling party, ONS master and picking party
are on the same shelf no CO route will be used.
– For call scenarios where the calling party is located on a different shelf
than the ONS master and ONS slave the CO route will be used. the
calling party will be charged.
– Tones
– The RING TYPE applied to ONS members is the same as the one of
the ONS master.
– When the payload survivability route is used, the called party hears
the "external call ring" despite the fact that it is an internal call.
• Fax-Modem
• Call Waiting
• Call Log
• OpenScape Xpressions basic scenarios
• ComAssistant basic scenarios
2.10.2 Configuration
General activation of the SPS feature:
CHANGE-ZANDE:TYPE=ALLDATA,SPS=YES;
For more information on the configuration please refer to Section 2.9.2, “How is
Payload Survivability Configured?”.
• Describe how source group (1) is reached with alternate routing table
ADD-
APRT:TYPE=ALTROUT,SRCGRP=1,ALRTYPE=ALR,ALTRTNR=00897229000,
ACCODE=9000,ARTCNR=1000,ARTCNRNG=30;
• Describe how source group (19) is reached with alternate routing table
ADD-
APRT:TYPE=ALTROUT,SRCGRP=19,ALRTYPE=ALR,ALTRTNR=00897229000,
ACCODE=9000,ARTCNR=1000,ARTCNRNG=30;
• Define code for incoming alternate route
• Source group needs to be configured in AMO TDCSU for all involved trunks
CHANGE-TDCSU:PEN=x-x-x-x,SRCGRP=1;
CHANGE-TDCSU:PEN=x-x-x-x,SRCGRP=19;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• AMO TWABE will be used for direct call to Xpression access numbers
ADD-TWABE:STNO=64,LEN=5;
..where 64 (TIE code to XPR, max. 3), 5 is total length of the number (TIE
code + length of the direct access number)
It should be noted that TWABE has no DPLN groups. The usage of block dial
feature might be used as alternative solution to AMO TWABE.
• Configuring code for force alternate route

ADD-WABE:xxx,,,FRCALTRT,N,,,,,,,,;
• Configuring station autorization
Stn COSSU must have autorization TTT (Transfer Trunk to Trunk) to allow
transfer over SPS
CHANGE-COSSU:TYPE=COS,COS=xx,AVCE=TTT;
IMPORTANT: The carrier must deactivate checking of the Calling Party Number
(CLIPNOSCREEN).
2.10.3 General Restrictions and Limitations

• SPS trunk groups must be configured for payload separation without intercept
parameters.
• Route optimization is not possible.
• Direct tie trunk access if the trunk is located in a different shelf is not possible.
Workaround: Use AMO TWABE or activate the Block Dial feature.
• Attendant scenarios are not supported.
• Only ComAssistant basic scenarios are supported. Other applications using

ACL (through CAP/CA4000) are not supported.
• Payload survivability ALR with single number and PUBDID are not supported.
• Virtual Numbering (VNR) is not supported.
• US specific scenarios are not supported.
• Direct station selection (DSS)
• Override/Intercept
• Camp on
• Only local announcements are supported; announcements are not routed via
ISDN (due to CO resource usage).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
• MLPP is not suported - MLPP calls over payload separation are not possible.
• Chese - Secretary and Executive must be located on the same branch.
• Broadcast, Speaker Call - One-Way - All party's must be located on the same
branch.
• ACD agents must be located on the same branch.
• PARK - Must not be used on different branches
• SIP Phones are not supported.
• ISDN, ANATE - only basic call is supported.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Divert Call in Survivability Mode to another Access Point
2.11 Divert Call in Survivability Mode to another Access Point

When Single StepTransfer is invoked for a DIGITE or an ANATE in talk state and
no path is available between source and destination, then the alternate path for
payload survivability is used if properly configured.
2.11.1 Prerequisites
• Each access point needs access to the PSTN over CO trunk and
corresponding alternate routes and numbers must be configured.
• Payload survivability or signaling and payload separation (see Section 2.10,

“Signaling and Payload Separation (SPS)”) must be configured.
• OpenScape Contact Center (OSCC) at least V8.
2.11.2 User Scenarios

Scenario 1
Call arrives on a trunk at IPDA in Location B (labeled #1 in the figure below).
OpenSape Contact Center requests that the call routes to an agent extension
which is located on the IPDA at Location C, which routes via PSTN due to
payload survivability (labeled #2 and #3).
Figure 31 Divert call in survivability mode - User scenario 1
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Scenario 2
Call arrives on a trunk at the IPDA in Location B (labeled #1 in the figure below).
The call routes to the main HiPath 4000 in Headquarters A via PSTN due to
payload survivability to play a Call Director message (labeled #2 and #3). This call
may be subsequently routed to an agent extension at the IPDA in Location C
either via payload survivability or over the WAN (labeled #4 and #5).
Scenario 3
Call arrives at the IPDA in Location B and routes to an agent extension (labeled
#1). This agent then consults, conferences, or transfers with an agent on the
IPDA in Location C (labeled #2), which routes via PSTN due to payload
survivability.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Scenario 4
Call arrives on a trunk at the main HiPath 4000 at Headquarters A (labeled #1),
and is routed to an agent extension on an IPDA at Location C (labeled #2 and
#3) via PSTN due to payload survivability.
2.11.3 Use Cases

1. Basic call
• ACD incoming call on AP x is routed directly to an agent on AP y.

Details:
– incoming call using CO trunk located on AP x
– call enters ACD queue
– agent available and OpenScape Contact Center routes the call to

agent on AP y using CSTA_DEFLECT_CALL_REQUEST
• ACD incoming call on HiPath 4000 host system is routed directly to an

agent on AP x.
Details:
– incoming call using CO trunk located on HiPath 4000 host system

agent on AP x using CSTA_DEFLECT_CALL_REQUEST
• ACD incoming call on AP x is routed directly to an agent on HiPath 4000

host system.
Details:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

agent on HiPath 4000 host system using
CSTA_DEFLECT_CALL_REQUEST
2. Scenarios with XMU (AMO RCSU) ports
• ACD incoming call on AP x is routed to XMU (HiPath 4000 host system)

and then redirected to an agent at AP x.
Details:
– incoming call using CO trunk located on AP x.
– call enters ACD queue and is connected to ACD music/

announcement port (check Note 2)


and then redirected to an agent at AP y.
Details:


agent on AP y using CSTA_DEFLECT_CALL_REQUEST

and then redirected to an agent at HiPath 4000 host system
Details:


agent on HiPath 4000 host system using
CSTA_DEFLECT_CALL_REQUEST
• ACD incoming call on HiPath 4000 host system is routed to XMU (HiPath
4000 host system) and then redirected to an agent at AP x
Details:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm


NOTE 1: In case that no agent becomes available during announcement, the

ACD call is routed back to RCG/DNIT via
CSTA_DEFLECT_CALL_REQUEST and then a new agent search begins.
I.e. use case 2 works for 2 cases:
a. an agent gets available during announcement
b. no agent gets available during announcement and a new search begins.
NOTE 2: If ACD music/announcements (XMU configured as RCSU ports)

are used, ACD only switches paths, connecting caller TSL with XMU TSL. If
no payload possible, there is no mechanism to use alternate path to listen to
these ports. The call is still in ACD queue and can be routed anytime to any
agent using CSTA_DEFLECT_CALL_REQUEST as described in Note 1
above. As alternative to RCSU ports, Call Directors can be used (see use
case Scenarios with Call Director (AMO SCSU) ports (analog device)).
3. Scenarios with Call Director (AMO SCSU) ports (analog device)
• ACD incoming call on AP x is routed to Call Director (HiPath 4000 host

system) and then redirected to an agent at AP x
Details:
– OpenScape Contact Center routes the call to Call Director on HiPath

4000 host system using CSTA_DEFLECT_CALL_REQUEST and
caller is connected with Call Director
– OpenScape Contact Center routes the call back in ACD queue using
CSTA_SINGLE_STEP_XFER_CALL_REQUEST, an agent becomes
available and OpenScape Contact Center routes the call to the agent
on APx using CSTA_DEFLECT_CALL_REQUEST
or
– OpenScape Contact Center routes the call to an agent on AP x using

CSTA_SINGLE_STEP_XFER_CALL_REQUEST

system) and then redirected to an agent at AP y
Details:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

available and OSCC routes the call to the agent on AP y using
CSTA_DEFLECT_CALL_REQUEST
or
– OpenScape Contact Center routes the call to agent on AP y using


system) and then redirected to an agent at HiPath 4000 host system
Details:

available and OpenScape Contact Center routes the call to agent on
HiPath 4000 host system using CSTA_DEFLECT_CALL_REQUEST
or
– OpenScape Contact Center routes the call to agent on HiPath 4000

host system using CSTA_SINGLE_STEP_XFER_CALL_REQUEST
• ACD incoming call on HiPath 4000 host system is routed to Call Director
(HiPath 4000 host system) and then redirected to an agent at AP x
Details:

A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
available and OpenScape Contact Center routes the call to the agent
on AP x using CSTA_DEFLECT_CALL_REQUEST
or
– OpenScape Contact Center routes the call to agent on A Px using

NOTE: In case that no agent gets available during announcement, the ACD
call is routed back to RCG/DNIT via
CSTA_SINGLE_STEP_XFER_CALL_REQUEST and then a new agent
search begins. I.e. use case 3 works for 2 cases:
a. an agent gets available during announcement
b. no agent gets available during announcement and a new search begins.
NOTE: This use case works if Call Director is located on AP x.
NOTE: This use case works if Call Director is replaced by a DIGITE.
4. Consultation, call transfer scenarios

In principle it could be that an agent wants to transfer a call to another agent
who can be located on the same or in another location where maybe no IP
resources are available. The call transfer can occur after every above
mentioned scenario.
NOTE: Update of numbers on the the phone display after transfer via
alternate routing is not possible.
5. Ring No Answer - which can occur after every above mentioned

scenario
The ACD call is already ringing, i.e. the destination agent is already seized
but not answering the call. After timeout the OpenScape Contact Center/ACD
takes the call back and routes it back to the RCG/DNIT via
CSTA_DEFLECT_CALL_REQUEST and starts with a new search for agents.
This scenario works regardless where the originator trunk is located (HiPath
4000 host sytsem/AP x or A Py) or where the old/new agent is located.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.11.4 Generation
No special AMO configuration is necessary.
Payload Survivability must be configured properly. The only supported

configuration is ALR via multichannel trunk circuit under one call number.
OpenScape Contact Center timer for ring no answer must be lower than no call
transfer parameter NOCALLTR in HiPath 4000.
Both timers (in HiPath 4000 and OpenScape Contact Center) have the default
value equal with 30. This leads to the following behavior: When the call comes
back from ISDN it is transferred to attendant console and it is not routed to Call
Director.
In HiPath 4000 the parameter can be changed using the following AMO
command:
e.g. CHANGE-CTIME:TYPESWU=TRK,NOCALLTR=35;
The instruction to change the timer in OpenScape Contact Center can be found
in OpenScape Contact Center Enterprise V8 R2, Manager Administration
Guide, Administrator Documentation > Section 8.3.2.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
External Music on Hold
2.12 External Music on Hold

If an internal sound type (SIU) is replaced by an external sound source (e.g.
music on hold), this new sound type is applied throughout the system.
In the example below (Figure 35 “Routes for music on hold: Supply in the central
system”) an external MusiPhone is configured in the central system, as is most
commonly the case.
IP payload connections to the central system are then required for all circuits in
IPDA access points that are switched to external MOH. If multiple circuits/
subscribers in one access point are connected to the same MOH, only one
payload connection (B channel) is connected for transmission of music between
the central system and the access point, and all relevant circuits of the AP cut in
to this.
All illustrated subscribers are

switched to music in the hold state HG3575
AP 17
MusiPhone HiPath 4000
HG3575
RCSU:HMUSIC 1
AP 18
IP Network HG3575
AP 19
HG3500
Figure 35 Routes for music on hold: Supply in the central system
IMPORTANT: If a circuit is switched to MOH, e.g. as a result of consultation hold,

the original payload connection remains active. In other words, the connection of
MOH uses an additional payload connection.
If the external MOH is supplied in an access point rather than on the central
system, the connections continue to be handled as explained below.
Circuits within the access point in which the MOH is supplied are switched to
MOH via the internal AP memory time switch. In other words, no additional
payload connections over IP are required.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

AP 17
HiPath 4000
HG3500 MusiPhone
IP Network
RCSU:HMUSIC 1
Figure 36 Routes for music on hold: Supply in access point 17 - local

subscriber
If circuits in the central system are switched to MOH, a payload connection

between the access point with the MOH source and the central system is
switched, from which all circuits of the central system are then operated.

AP 17
HiPath 4000
MusiPhone
RCSU:HMUSIC 1
IP Network
HG3500
Figure 37 Routes for music on hold: Supply in access point 17 - central

subscriber
If circuits of other access points are switched to MOH, a separate payload

connection to the central system is switched for these access points. The central
system is connected to the access point with the MOH source via a second
payload connection. MOH connections between access points are therefore
always switched via the central system.
There is no alternative routing via access point <-> access point connections if
there are not enough or no resources available for the route via the central
system.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

switched to music in the hold state HG3575 MusiPhone
Classmark VIAHHS set
AP 17 RCSU:HMUSIC 1
Classmark ML set
HiPath 4000
HG3575
AP 18
IP Network HG3575
AP 19
HG3500
Figure 38 Routes for music on hold: Supply in access point 17 - subscriber in

different AP
Configuration Management --> Station --> Special Stations

Click Search and select the special station (Station Type: EXTANS).
Set or delete the required classmarks on the Features tab and Save.
ADD-SSC:PEN=1-2-37-10,TYPE=EXTANS,CPCALL=HOLD,
CLASSMRK=G711&ML;
or
CHANGE-RCSU:PEN=1-2-37-5,CLASSMRK=G711&&ML;
IMPORTANT: With CHANGE, please note that you must specify all classmarks
that are to be set. Classmarks that were set prior to the changes will not be taken
over. 
Always specify the classmark ML, otherwise an individual payload connection to
the source HG 3575 will be set up for each circuit on a HG 3575 that requires
active MOH. As a result, considerable bandwidth and B channel resources are
consumed.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Classmark VIAHHS not set AP 17 RCSU:HMUSIC 1
Classmark ML set
HG3575
AP 18
IP Network HG3575
HiPath 4000 AP 19
Communication
server

different AP

Classmark VIAHHS not set AP 17 RCSU:HMUSIC 1
Classmark ML not set

HG3575
AP 18
Not recommended!!!
HG3575
IP Network
HiPath 4000 AP 19
Communication
server

different AP
Multiple Music on Hold

With IPDA-based branch concepts, a requirement exists for the setting of
different music on hold for different branches.
With the aid of flex routing, up to 150 different announcements can be used in the
system. The announcements are assigned on a subscriber basis.
If all subscribers of an access point are assigned the same MOH and this MOH
is supplied locally in the access point, no payload connections over IP are
required for MOH. If, however, a subscriber is assigned MOH that is supplied in
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
a different access point, two payload connections over IP are switched - one from
the MOH source to the central system and one from the central system to the AP
of the subscriber.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Information on CMI
2.13 Information on CMI

Please refer to the project planning guideline of HiPath Cordless E in TI-Online.
https://ti-online.global-intra.net/produktiv/en/z3-hp4-70a.pdf
Home page TI - Online:
https://ti-online.global-intra.net/index.html
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
2.14 IP Address Changes

Unfortunately, the correct configuration of the IP addresses of all IPDA
components at the time of installation is not all that is required. Restructuring of
the IP network of the customer, which also affects the addressing of the IPDA
components, is part of day-to-day business.
Whenever an IP address has to be changed, there is no avoiding a brief

interruption in operation. In order to minimize the effects for the users of the
HiPath 4000 system, the procedure for changing addresses must be planned
meticulously.
In the following scenarios, it is always assumed that the changes involved are
changes that affect the entire LAN segment to which the IPDA components are
connected, and not just the address of an individual component.
A distinction is made between three cases in this context:
• Change of Address in a Network Segment to which Access Points are

Connected
• Changing the Address of the Survivability Network
• Changes in the HiPath 4000 LAN Segment
2.14.1 Change of Address in a Network Segment to

which Access Points are Connected
Let us use the configuration of Access Point AP99 as an example:
• It is to be reached from the HiPath 4000 LAN segment via Router Ra

(192.168.1.254).
• It is to reach other networks via Router Rx (192.168.23.1).
• Its own IP address is 192.168.23.99.
• The IP address for the TAP is 192.168.23.199.
• The netmask of the network in which the access point is located is

255.255.255.0
As this involves a change of the entire network segment, AP 98 is also affected

with APIPADDR=192.168.23.98.
We receive the following information from the customer’s network administrator:
Name NEW address OLD address

Netmask 255.255.255.224 255.255.255.0
Table 19 Change of address in “networked“ access points
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes

Router Rx 10.123.87.222 192.168.23.1
AP 98 APIPADDR 10.123.87.198 192.168.23.98
AP 99 APIPADDR 10.123.87.199 192.168.23.99
Table 19 Change of address in “networked“ access points
192.168.1.254 192.168.23.99
AP 99
10.123.87.199 HG
STMI-1 STMI-2
Peripheral
HG 3575 Boards
3570
Ra Rx AP 3300 IP
Router Router
HG
AP 98
3570 IP N et wor k HG Peripheral
H iPath 4 000 L AN Seg m ent
192.168.23.1 3575 Boards

10.123.87.222
AP 3300 IP, AP 3500/3505
Peripheral
Boards
255.255.255.0
255.255.255.224
Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP
AP 18
HG Peripheral
3575 Boards
CC-A R1
Router AP 3300 IP, AP 3500/3505
PS T N N e t wo r k
AP 17
3575 Boards
Router
CSTA AP 3300 IP, AP 3500/3505
Assis
tant
HiPath
4000
Figure 41 Change of address in “networked“ access points
The time of the address change in the access points is critical.
If parallel operation of both network addressings cannot be configured in the

customer network during the transition period, the address change must be
oriented to the time of transition of Router Rx and the change in routing in the
customer network.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
The address change must be performed prior to the reconfiguration of Router Rx

and started on the access point via EXEC-USSU:UPDATAP. Existing links are
disconnected. After reconfiguring the router, we would no longer be able to reach
the access point and would only be able to implement the address change locally
at the access point.
IMPORTANT: Prior to the EXEC-USSU:UPDATAP, the configuration must be

updated on the system hard disk. Otherwise, the data on the system would
conflict with the data on the HG 3575 when the system is reloaded and could only
be synchronized again with EXEC-USSU:UPDATAP,LTU number,UL.
As soon as the access point has restarted with the new address, the HiPath 4000
central switch can no longer reach it via the signaling survivability route (if
configured), or can only reach it via this route. This applies until the routing in the
customer network has likewise been changed.
IMPORTANT: If special routes are used in the configuration of the IPDA system
(in access points or for HG 3500 modules), these must all be checked and, if
necessary, modified. (CHANGE-APRT:TYPE=ROUTTBL ...)
Generation
Point
Change the addresses on the IP Interface tab and Save.
Data
CHANGE-APRT:TYPE=APNET,LTU=98,APIPADDR=10.123.87.198,
NETMASK=255.255.255.224;
CHANGE-APRT:TYPE=APNET,LTU=99,APIPADDR=10.123.87.199,
NETMASK=255.255.255.224;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
2.14.2 Changing the Address of the Survivability

Network
This case scenario, while unlikely, is simple to realize in the HiPath 4000 switch.
All addresses in the survivability network are fixed addresses derived from the
network address.
Data
Click Search, change the survivability network address on the System Data
tab and Save.
Data
CHANGE-SIPCO:TYPE=LSNET,SURVNET=192.168.123.0;
The change within the access points becomes effective after

for all affected access points.

system hard disk.
IMPORTANT: As ports of the survivability router are also affected by the address
change, the routers also have to be reconfigured.
However, this may not be performed until after conversion of the access points.
2.14.3 Changes in the HiPath 4000 LAN Segment

This is the most complicated change of all, and the one which harbors the
greatest risk, which is why address changes in the HiPath 4000 LAN segment
should be avoided whenever possible.
The reason is the security concept of IPDA. An access point may only be
controlled by CC-A or CC-B. To this end, the IP addresses of the two processors
are configured in the access point. If these addresses change, the access point
can no longer be controlled and would have to be reconfigured locally.
This potentially risky task was improved in HiPath 4000 V6 R2. Since this version
there is a possibility to connect to the access point from arbitrary IP address if
there is no active HSR connection. So it is possible to open a new connection and
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
transfer the configuration data to the access point or HiPAth 4000 SoftGate and
establish the regular control connection. After this step the original security
mechanism , that means the remote CC-A, CC-B address check, is activated
again.
Furthermore, if the control connection to an access point can not be open, there
is a possibility to start an SSH session to its control IP address and perform the
configuration changes manually.
AP 99
HG
STMI-1 STMI-2
Peripherie-
HG 3575 Baugruppen
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
AP 98
3500 HG Peripherie-
3575 Baugruppen
IP Network
AP 3300 IP, AP 3500/3505
Peripherie-
Baugruppen
Ry
AP 43
HG Peripherie-
Router 3575 Baugruppen
!!!UW7
AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP
AP 18
HG Peripherie-
3575 Baugruppen
CC-A R1
AP 3300 IP, AP 3500/3505
Router
P S T N N e tw o r k
AP 17
CC-B R10 HG Peripherie-
3575 Baugruppen
Router
AP 3300 IP, AP 3500/3505
CSTA
Assis
tant
HiPath
4000
Figure 42 Installation example
We receive the following information from the customer’s network administrator:

Netmask 255.255.255.224 255.255.255.0
Network address 10.123.1.64 192.168.1.0
CC-A 10.123.1.65 192.168.1.1
CC-B 10.123.1.66 192.168.1.2
ADP 10.123.1.67 192.168.1.3
Router Ra 10.123.1.94 192.168.1.254
Router R1 10.123.1.83 192.168.1.101
Router R10 10.123.1.93 192.168.1.102
AP 17 10.123.1.77 192.168.1.17
Table 20 Address change in HiPath 4000 LAN segment
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes

AP 18 10.123.1.78 192.168.1.18
STMI-1 10.123.1.68 192.168.1.10
STMI-2 10.123.1.69 192.168.1.11
Table 20 Address change in HiPath 4000 LAN segment
The following procedure avoids local reconfiguration of the access points.
IMPORTANT: For HiPath 4000 V6 R1 and prior versions: The changes must be
implemented before the routing in the customer network is changed.
Step 1
Change the IP addresses in the HiPath 4000 LAN segment.
Data
Click Search, change the IP addresses and, if required, Network Mask on
the System Data tab and Save.
CHANGE-SIPCO:TYPE=LSNET,NETADDR=10.123.1.64,
NETMASK=255.255.255.224,DEFRT=10.123.1.94,
CCAADDR=10.123.1.65,CCBADDR=10.123.1.66;
This results in the addresses being changed. However, the change is not effective
until the system has been restarted, which must be the last step performed in this
sequence.
Step 2
The CC-A and CC-B address changes implicitly for “networked“ access points.
LSRTADDR must be explicitly modified as well as the address of the router on the
HiPath 4000 LAN segment (Router Ra) used for configuring the signaling
connection.
Point
Change the address of the router in the network on the IP Interface (NW)
tab and Save.
Data
CHANGE-UCSU:UNIT=AP,LTU=xx,LSRTADDR=10.123.1.94;
for every “networked“ AP, i.e. in this example 43, 98 and 99.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
This puts the access points out of operation until both the CC address change in
the system is effective and the routing in the customer network has been
changed. Existing links are disconnected.
Step 3
Change the HiPath 4000 LAN addresses of the “direct link“ access points.
It is assumed in this context that the addressing in the internal network of the
“direct link“ access points is not changed.
Point
Change the address of the router in the network on the IP Interface (DL) tab
and Save.
Data
CHANGE-UCSU:UNIT=AP,LTU=17,LSRTADDR=10.123.1.77;
EXEC-USSU:UPDATAP,17;
CHANGE-UCSU:UNIT=AP,LTU=18,LSRTADDR=10.123.1.78;
EXEC-USSU:UPDATAP,18;
This puts the access points out of operation until the CC address change in the
system is effective. Existing links are disconnected.
Step 4
Change the survivability router addresses at the HiPath 4000 LAN segment.
In the example, this involves Routers R1 and R10. In order to change their
addresses in the HiPath 4000 LAN segment, they must be deleted from the
configuration and re-entered.
Unfortunately, a survivability router cannot be deleted until no more access points

are configured on this router.
In this example, these are the access points 18, 43 and 98 which are configured
for signaling survivability. Here, too, the configuration must be deleted and re-
entered again.
The address configuration of the survivability routers (e.g. WAML) must, of

course, be modified as well.
The overall procedure is as follows:
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
Point
Delete the router number on the General tab under Signaling Survivability
and Save.

Signaling Survivability Router
Click Search and select router --> Delete.
Click New, enter router with modified data and Save.
Point
Enter the router number on the General tab under Signaling Survivability
and Save.
DELETE-APRT:TYPE=SURV,CONF=ROUTER,ROUTERNO=1;
ADD-APRT:TYPE=SURV,CONF=ROUTER,ROUTERNO=1,
LSADDR=10.123.1.83;
ADD-APRT:TYPE=SURV,CONF=AP,LTU=43,ROUTERNO=1;
DELETE-APRT:TYPE=SURV,CONF=ROUTER,ROUTERNO=10;
LSADDR=10.123.1.93;
Step 5
Change the addresses of the HG 3500 modules:

Change the address on the STMI Board Data tab under IP Gateway and
Save.
CHA-BCSU:TYPE=IPGW,LTU=5,SLOT=85,IPADDR=10.123.1.68;
CHA-BCSU:TYPE=IPGW,LTU=5,SLOT=91,IPADDR=10.123.1.69;
IMPORTANT: If special routes are used in the configuration of the IPDA system
(between access points and HG 3500), these must all be checked and, if
necessary, modified. (CHANGE-APRT:TYPE=ROUTTBL ...)
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
IP Address Changes
Subsequently, the changed addresses have to be loaded on the HG 3500

modules via:
Configuration Management --> System Data --> Maintenance --> Board

Maintenance
with OK.
RESTART-BSSU:ADDRTYPE=PARTNO,PARTNO=Q2316-X,FCTID=1;
Step 6
To complete the procedure, the HiPath 4000 switch now has to be reset in order
for the addresses configured with SIPCO to become effective.
The restart can only be initiated in expert mode.

(see AMO command)
EXEC-REST:UNIT,BP,SOFT;
Contact with the “networked“ access points cannot be re-established until the
routing in the customer network has also been changed.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
A-Law/µ-Law Conversion in AP Shelf
2.15 A-Law/µ-Law Conversion in AP Shelf

It is possible to connect telephones in AP shelves that work with companding
algorithms different to the host system (e.g. host system in Germany (A-law),
access point in the USA (µ-law)).
2.15.2 Service Information

Conversion is supported for
• SIP and H323 trunk and
• HFA, SIP, TDM and analog subscribers.
Restrictions:
• TDM phone optiset E Advance do not support µ-law.
2.15.3 Generation (Example)

CHANGE-UCSU:UNIT=AP,LTU=17,CONVLAW=YES;
It is necessary to reset the NCUI board in order to activate the functionality. From
this moment AP shelf works in a different law against host system. The NCUI
represents a G711 law conversion point.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
Different Announcements, Tones and DTMF DialTone Receivers per Access Point
2.16 Different Announcements, Tones and DTMF DialTone Receivers per

Access Point
With HiPath 4000 V6 it is possible to configure different languages/countries for
each access point with AMO UCSU. Therefore different access points can have
the same or different SIU-Init-Data files.

This feature enables you to set tones and announcements for each access point
on a country and language-specific basis. This means that stations will hear
suitable tones and announcements for the set country/language. These are
created by the SIU part of the NCUI board. Individual tones can also be assigned
varying SIU functions on an access point-specific basis. In addition, the country
code can also be set specific to the access point.
Figure 43 Feature overview
All known subscriber types (analog, digital, IP) can be used.
Analog subscriber boards can be configured per access point on a country-

specific basis (this may be necessary, for example, to set the correct companding
algorithm).
The dial tone receiver of the SIU part of the NCUI can also be configured on a
country-specific basis.
External announcement devices (configurable via AMO SSC) can be assigned to

all host and AP shelves or to individual shelves only (all host shelves certain AP
shelves).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
The feature is valid for classic access points and for soft APs.
2.16.2 Service Information

If the same country and language settings as the host system are applied to all
access points, configuration can be performed as in HiPath 4000 V5 and earlier
systems. Please note, however, that system-wide settings (via AMO ZAND) must
be performed before the access points are configured. If system-wide settings are
subsequently changed, these apply only to host shelves. If they should also apply
to access points, you must set them individually for each affected access point.
The following system-wide settings (via AMO ZAND) can also be access point-
specific:
AMO ZAND
D1 = typ, D2 = parameter (Deutsch)
E1 = typ, E2 = param (English)
(D1) DATENALL (D1) DATENALL (D1) TOENE (D1) TOENE
(D2) SIUSPKZ (D2) LANDKZ (D2) SIU (D2) HZE
(E1) ALLDATA (E1) ALLDATA (E1) TN (E1) TN
(E2) SIUANN (E2) CNTRYCD (E2) SIUC (E2) DTR
Funktion /  SIU Ansagen /  Länderkennzeich SIU Töne /  Hörzeichenempf
function SIU en für Steuerung SIU tones änger /
announcements Baugruppenload dial tone receiver
ware SLMA / 
Country code to
control board
loadware SLMA
Table 21 Access point-specific configuration
Access point-specific settings are performed with AMO UCSU. The parameter
names in AMO ZAND are used as they are for the new parameters in AMO
UCSU.
If one of these settings is changed while the access point is in operation (via
CHANGE-UCSU), the ACDR or tone parameter must be loaded manually. This is
done via the EXEC-USSU:NCUILOAD; command.
The change only takes effect when the affected NCUI board is reset. This is done
via the EXEC-USSU:UPDATAP;.
If these system-wide settings are subsequently changed, these changes apply

only to host shelves. If they should also apply to access points, the changes must
also be performed on an access point-specific basis.
Special behavior for the setting for the USA:
In the USA, the companding algorithm µ-law is used (in all other countries, A-law
is used).
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
In HiPath 4000 V5 R1 and later systems, it is possible to connect telephones in

AP shelves that work with companding algorithms different to the host system
(e.g. host system in Germany, AP in the USA). There was the restriction that no
analog telephones may be connected in these AP shelves. With the feature
"Different Announcements per Access Point", this restriction is lifted and even if
the companding algorithms in the access point and host system are different,
analog telephones may still be connected in the AP shelves. See also Section
2.15, “A-Law/µ-Law Conversion in AP Shelf”.
Restrictions
• The functions of peripheral SIU (SIU type 2 and 3, SIU TDS) are not access
point specific configurable, i.e. the system wide setting is valid for all access
points (in HiPath 4000 SoftGate access point there is no peripheral SIU
possible at all).
• Music on hold (MOH)

Even though music on hold (MOH) is lanuguage/country independent it is still
not configurable per access point.
• Other country-specific features like MFC variants, loadware variant for

SLMA2 / SLMAR, country specific tones and attenuation for conference
board of compact hardware and SCC board, etc are only supported system
wide.
2.16.3 Generation Example

The following examples only list the AMOs/parameters that can be set on an
access point-specific basis and thus only illustrate part of the total configuration.
2.16.3.1 Access Point in a different Country to the Host System
First, the parameters must be set for the host system (e.g. Germany):
CHANGE-ZAND:TYPE=ALLDATA,CNTRYCD=0,SIUANN=1;
CHANGE-ZAND:TYPE=TN,SIUC=0,DTR=0,RDS=0,CONFC=0;
Now the tones/announcements for another country (e.g.: Italy) can be set for an
access point:
",SRCGRP=17,FRMTYPE=L80XF,CONNTYPE=APDL,LSRTADDR=198.16.16.63,AP
RTADDR=198.16.16.150,LOCID=017,LOCATION="LOCATION",PHONE=3140,FA
X=3141,PLCHECK=YES,BCHLCNT=60,CONVLAW=NO,TCLASS=0,ALARMNO=0,SIUA
NN=A,SIU=D,DTR=D,CNTRYCD=D;
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
2.16.3.2 Access Point with different Companding Algorithm
First, the parameters must be set for the host system (e.g. Germany):
CHANGE-ZAND:TYPE=ALLDATA,CNTRYCD=0,SIUANN=1;
CHANGE-ZAND:TYPE=TN,SIUC=0,DTR=0,RDS=0,CONFC=0;
Now tones/announcements can be set for an access point for a country with a
different companding algorithm (USA):
",SRCGRP=17,FRMTYPE=L80XF,CONNTYPE=APDL,LSRTADDR=198.16.16.63,AP
RTADDR=198.16.16.150,LOCID=017,LOCATION="LOCATION",PHONE=3140,FA
X=3141,PLCHECK=YES,BCHLCNT=60,CONVLAW=YES,TCLASS=0,ALARMNO=0,SIU
ANN=D,SIU=K,DTR=K,CNTRYCD=K;
If the companding algorithm is changed while the access point is already in
operation (via CHANGE-UCSU), the access point must first be deactivated (via
DEACTIVATE-USSU). Only when you have completed this action will the
CONVLAW parameter be considered when changing. Finally, you should
reactivate the access point (via ACTIVATE-UCSU).
2.16.3.3 Access Point with individual CP Tone <-> SIU Function

Assignment
When setting system-wide tones (via AMO ZAND), the standard assignment of
CP tones to SIU functions is also set for the system. This assignment can be
adapted system-wide via AMO ZAND (TYPE=TONES, parameter CPCALL and
SIU).
When setting access point-specific tones (via AMO UCSU), the standard
assignment of CP tones to SIU functions for the corresponding access point is
also set. This assignment can be adapted via AMO UCSU (parameter CPCALL
and SIU) to as specific access point.
Example: assign the CP tone "Not possible" to the SIU function 0:

CHANGE-UCSU:UNIT=AP,LTG=1,LTU=17,CPCALL=NOPO,SIU=0;
2.16.3.4 External Announcement Devices
CP tones can also be assigned to external announcement devices that can be

configured via AMO SSC to an analog board. External announcement device
assignment to CP tone can be configured on a system-wide or individual basis
• for all host shelves only, or
• for all host shelves and x access points, or
• for x access points only.
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm
(x stands for one or all APs)
If the AMO SSC is configured for announcement devices such as those in HiPath
4000 V5 and earlier systems, this means that the setting applies to all shelves
(host and AP). If the announcement devices is to be configured individually for
certain shelves, the parameter LTU should be entered. This means that entering
a host shelf applies the setting to all host shelves and entering an AP shelf (or AP
shelf area) applies the setting to the AP shelf (or to the corresponding AP
shelves).
You can configure up to 300 different external announcement devices.
1. Setting external announcement devices system-wide:

ADD-SSC:PEN=1-18-1-0,TYPE=EXTANN,CPCALL=INTDTN;
2. Setting external announcement devices for all host shelves only:
ADD-SSC:1-18-1-0,EXTANN,INTDTN,LTU=1;
3. Setting external announcement devices for all host shelves and an AP shelf:
ADD-SSC:PEN=1-18-1-0,TYPE=EXTANN,CPCALL=INTDTN,LTU=1;
ADD-SSC:PEN=1-18-1-0,TYPE=EXTANN,CPCALL=INTDTN,LTU=17;
4. Setting external announcement devices for multiple AP shelves:
ADD-SSC:PEN=1-18-1-0,TYPE=EXTANN,CPCALL=INTDTN,LTU=17;
ADD-SSC:PEN=1-18-1-0,TYPE=EXTANN,CPCALL=INTDTN,LTU=20;
2.16.4 Relevant AMOs

Language
SSC TYP=EXTANS d Externe Ansage
TYPE=EXTANN e External announcement
LTU d LTU-Nummer
LTU e LTU Number
UCSU CPTON d Vermittlungstechnischer Ton
CP e Call processing tone
HZE d Auswahl der länderspezifischen
Hörzeichenempfängertabelle
DTR e Selection of country-specific dial tone
receiver table
KONVLAW d A-Law/Mu-Law Konvertierung auf der
NCUIx-Baugruppe
CONVLAW e A-Law/Mu-Law conversion on NCUIx board
LANDKZ d Loadwarevariante für SLMA2 / SLMAR
CNTRYCD e Loadware variant for SLMA2 / SLMAR
A31003-H3160-S104-8-7620, 07/2014
02_ipda.fm

Language
SIU d Auswahl der länderspezifischen SIU-
Tontabelle
SIUC e Selection of country-specific SIU tone table
SIUSPKZ d Sprachkennzeichen für SIU-Texte
SIUANN e Set options for SIU announcement texts
SIUTON d Zugeordneter Ton der SIU
SIU e Assigned siu tones
ZAND HZE d Auswahl der länderspezifischen
Hörzeichenempfängertabelle
DTR e Selection of country-specific dial tone
receiver table
LANDKZ d Loadwarevariante für SLMA2 / SLMAR
CNTRYCD e Loadware variant for SLMA2 / SLMAR
SIU d Auswahl der länderspezifischen SIU-
Tontabelle
SIUC e Selection of country-specific SIU tone table
SIUSPKZ d Sprachkennzeichen für SIU-Texte und
SWU-Displaytexte
SIUANN e Set options for SIU announcement texts
TYP=TONTBL d Zuordnungstabelle CP-Ton -> SIU-Ton
TYPE=TONES e Tone table, assignment of CP tones to SIU
tones
CPTON d Vermittlungstechnischer Ton
CP e Call processing tone
SIUTON d Zugeordneter Ton der SIU
SIU e Assigned siu tones
A31003-H3160-S104-8-7620, 07/2014
03_load_calculation.fm
Load Calculation
3 Load Calculation
The following bit rate calculations only take one direction into account. The route
back in the opposite direction requires the same bit rate.
If a “shared medium“ is used for both directions, i.e. both directions are routed via
the same line, then both directions also have to be included in the calculation.
This is the case with 10Base5, 10Base2 and 10BaseT or 100BaseT half-duplex.
The Ethernet Media Access Layer (MAC) is realized pursuant to the IEEE 802.3
/ DIX Ethernet II Standard with MAC-Type 0800 (IP) in the case of the IPDA
components. The alternative pursuant to IEEE 802.3 and 802.2 LLC/SNAP is not
customary and would require greater bandwidth.
The calculations have been performed with active VLAN Tagging pursuant to
IEEE 802.1q. This yields the higher network load. Without VLAN Tagging, the
packet size is reduced by 4 octets (bytes).
IMPORTANT: The bit rate calculation used in this manual differs from that used
in previous versions.
By popular demand, the bit rate is no longer specified on the Physical Layer
(PHY), but instead on the Media Access Layer (MAC).
The 8 bytes for the preamble are no longer included in the calculation.
Payload transport with RTP (Realtime Transmission Protocol)
Codec Sample Payload Ethernet Ratio Ethernet load Ratio

type size packet size Overhead / No preamble RTP / ISDN
[ms] [Octets] [Octets] Payload [kbps] bit rate
G.711 20 160 222 39% 88.8 139%
G.711 30 240 302 26% 80.5 126%
G.711 60 480 542 13% 72.3 113%
G.729A 20 20 82 310% 32.8 51%
G.729A 40 40 102 155% 20.4 32%
G.729A 60 60 122 103% 16.3 25%
Table 22 Load calculation for an RTP connection (VoIP)

The G.711 codec generates a sample every 125 µs.
The G.729A codec generates a 10-octet frame every 10 ms.
The overhead calculation is based on the following:
Protocol Overhead
RTP 12
Table 23 Overhead with RTP connections
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Protocol Overhead
UDP 8
IP 20
IEEE 802.1Q VLAN Tagging 4
Ethernet MAC (DA,SA,TYPE,FCS - no preamble) 18
Total 62
Table 23 Overhead with RTP connections
The transmission bit rate depends not only on the codec type used and the
sample size, but also on the stack layer on which the bit rate is calculated. Details
on configuring the RTP payload can be found in Section 3.3, “Calculation Basis -
Configuring Payload Packets”.
In this document, the “worst case“ on the physical layer is always considered, i.e.
the Ethernet MAC frame including FCS with activated VLAN tagging. The bit rates
on higher stack layers are also important when calculating the load following
implementation on other media. The table below provides an overview. The
values are specified in Kbps and apply to an RTP connection in one direction:
Stack layer Codec type / Sample size

(Protocol)
G.711 G.729
20 ms 30 ms 60 ms 20 ms 30 ms 60 ms
RTP 68.8 67.2 65.6 12.8 10.4 9.6
UDP 72.0 69.3 66.7 16.0 12.0 10.7
IP 80.0 74.7 69.3 24.0 16.0 13.3
Ethernet 84.0 79.5 71.7 31.2 19.6 15.7
No preamble
No VLAN TAG
Ethernet 85.6 80.5 72.3 32.8 20.4 16.3
No preamble
With VLAN TAG
Ethernet 87.2 81.6 72.8 34.4 21.2 16.8
With preamble
No VLAN TAG
Ethernet 88.8 82.7 73.3 36.0 22.0 17.3
With preamble
With VLAN TAG
Table 24 Load for an RTP connection [Kbps]- by stack layer
RTP load during inactivity of VAD or DMC master connections

If “idle“ is detected when Voice Activity Detection has been enabled, audio signals
will not be transmitted temporarily. Nonetheless, the load on the RTP connection
does not drop completely to zero because data continues to be transmitted on the
RTP connection to check the connection and (depending on the codec) to
transmit the background noise. This data is referred to as SID frames (Silence
Insertion Descriptor). The RTCP connection is not affected by VAD.
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Stack Layer Codec Type

(Protocol)
G.711 G.729
RTP 1.8 1.1
UDP 2.5 1.8
IP 4.1 3.4
Ethernet, No preamble, No VLAN TAG 4.9 4.2
Ethernet, No preamble, With VLAN TAG 5.2 4.5
Ethernet, With preamble, No VLAN TAG 5.5 4.8
Ethernet, With preamble, With VLAN TAG 5.8 5.1
Table 25 Load on an RTP connection [kbps] with VAD during inactivity
The payload connection is controlled via the parallel RTCP connection

(Realtime Transmission Control Protocol)
A Sender Report message is sent by each relevant connection partner every five
seconds for every RTP connection. No Receiver Reports are sent. This produces
a load of 0.2 Kbps in each direction. The packet size was once again calculated
with VLAN tag and preamble.
Report type Report interval Average Ethernet Ethernet load

[s] packet size excl. preamble
[Octets] [Kbps]
Sender report 5 130 0.2
Table 26 Load calculation for an RTCP connection
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Load Calculation for Access Points
3.1 Load Calculation for Access Points
IMPORTANT: The estimated bandwidth of 32kBit/s (minimum bandwidth) or

64kBit/s for TCP signaling is sufficient for call processing operation. Initial
operation and loading of the boards in an AP shelf (sometimes with large
loadware volumes) are also controlled via TCP this can result in very long initial
operation times!
Calculation of the high-priority load for an individual access point
Protocol Data type Maximum bit Total bit rate [Kbps]

rate/ port with
[Kbps] N payload ports
N=30 N=60 N=120
RTP VoIP 88.8 2,664 5,328 10,656
RTCP VoIP 0.2 6 12 25
TCP/IP Signaling 64.0 64 64 64
TCP/IP Supervisory 0.1 4 8 15
(only if signaling
supervisory is configured)
Total load 2,738 5,412 10,760
Table 27 High-priority load of an access point (G.711/20 ms sample size)
The requisite bit rate for a supervisory connection depends on the configuration
of the keep-alive timer for this connection. The parameter to this end is
SUPVTIME in the TIMING branch of the AMO SIPCO. The maximum values are
specified in the table.
The load which is generated through signaling and control between the HiPath
4000 central system and an access point - which is also a high-priority load - has
been specified globally as 64 Kbps.
However, the actual load depends on the number of subscriber lines, CO and tie
trunks and the actual telephone usage behavior in the access point.
If, however, modules are reloaded, additional load is generated which, in the case
of limited bandwidth, can delay the signaling.
The absolute minimum of signaling bandwidth required is 32 kbps. If less than 64

kbps signaling bandwidth is available, traffic shaping must be enabled and set to
the actual bandwidth available. See Section 2.7.1, “Restriction of the Available
Signaling Bandwidth (Traffic Shaping)”.
In addition to high-priority load, low-priority load portions may also arise in certain
situations for the following:
• SNMP queries via network management
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
• TAP/Service PC access at the access point
• FTP-loading of a new HG 3575 loadware as a background task
High-priority load of an access point as a function of codec type and

sample size
Codec type Sample RTP load [Kbps] with Total Ethernet load [Kbps]
size N payload ports with N payload ports
N=30 N=60 N=120 N=30 N=60 N=120
G.711 20 2,664 5,328 10,656 2,738 5,412 10,760
G.711 30 2,416 4,832 9,664 2,490 4,916 9,768
G.711 60 2,168 4,336 8,672 2,242 4,420 8,776
G.729A 20 984 1,968 3,936 1,058 2,052 4,040
G.729A 40 612 1,224 2,448 686 1,308 2,552
G.729A 60 488 976 1,952 562 1,060 2,056
Table 28 High-priority load of an AP as a function of codec and sample size
Note
This appraisal must be treated with caution, as the utility of the G.729A codec
is limited by various factors:
• The call is transferred uncompressed if one of the subscribers/circuits

involved prevents compression
• Connections with fax, modem and data terminal devices are only
transferred uncompressed
• External music and announcements are mostly transferred

uncompressed (depends on the configuration (RCSU-CLASSMRK))
• Connections to a conference unit are mostly switched without

compression (depends on the configuration (ZAND-IPDAVCCF))
In all of these cases, either G.711 is used, or no codec at all.
The bit rates for G.711 thus apply.

In order to guarantee that bottlenecks are never encountered in the available
bandwidth, the access point link must be designed for the G.711 bit rate.
By means of statistical appraisals, taking the actual configuration into account

(how many fax/data devices are actually deployed, how many compression
licenses are available, are all possible subscriber/access circuits configured for
compression, how frequently are conferences used), a mixed calculation can be
performed.
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
The load as a function of a sample size can only be used if it is ensured that all
IPDA components are configured exclusively for this sample size. Otherwise, the
worst value for the respective codec type would have to be used for reasons of
reliability.
High-priority load of an access point as a function of the maximum number

of B-channels
Maximum Total Ethernet load Total Ethernet load Total Ethernet load
permissible at G.711/20ms at at G.711/60ms
number of B- [Kbps] G.711/30ms [Kbps]
channels [Kbps]
1 153 145 137
2 242 226 209
3 331 306 282
4 420 387 354
5 509 468 427
6 598 549 499
7 687 629 571
8 776 710 644
9 865 791 716
10 954 872 789
11 1,043 952 861
12 1,132 1,033 934
13 1,221 1,114 1,006
14 1,310 1,195 1,079
15 1,399 1,275 1,151
16 1,488 1,356 1,224
17 1,577 1,437 1,296
18 1,666 1,517 1,369
19 1,755 1,598 1,441
20 1,844 1,679 1,514
21 1,933 1,760 1,586
22 2,022 1,840 1,659
23 2,111 1,921 1,731
24 2,200 2,002 1,804
25 2,289 2,083 1,876
26 2,378 2,163 1,948
27 2,467 2,244 2,021
28 2,556 2,325 2,093
Table 29 High-priority load of an AP as a function of the permissible B-
channels
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels [Kbps]
29 2,645 2,406 2,166
30 2,734 2,486 2,238
31 2,823 2,567 2,311
32 2,912 2,648 2,383
33 3,001 2,729 2,456
34 3,090 2,809 2,528
35 3,179 2,890 2,601
36 3,268 2,971 2,673
37 3,357 3,052 2,746
38 3,446 3,132 2,818
39 3,535 3,213 2,891
40 3,624 3,294 2,963
41 3,713 3,375 3,036
42 3,802 3,455 3,108
43 3,891 3,536 3,181
44 3,980 3,617 3,253
45 4,069 3,697 3,325
46 4,158 3,778 3,398
47 4,248 3,859 3,470
48 4,337 3,940 3,543
49 4,426 4,020 3,615
50 4,515 4,101 3,688
51 4,604 4,182 3,760
52 4,693 4,263 3,833
53 4,782 4,343 3,905
54 4,871 4,424 3,978
55 4,960 4,505 4,050
56 5,049 4,586 4,123
57 5,138 4,666 4,195
58 5,227 4,747 4,268
59 5,316 4,828 4,340
60 5,405 4,909 4,413
61 5,494 4,989 4,485
62 5,583 5,070 4,558
channels
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels [Kbps]
63 5,672 5,151 4,630
64 5,761 5,232 4,703
65 5,850 5,312 4,775
66 5,939 5,393 4,847
67 6,028 5,474 4,920
68 6,117 5,555 4,992
69 6,206 5,635 5,065
70 6,295 5,716 5,137
71 6,384 5,797 5,210
72 6,473 5,878 5,282
73 6,562 5,958 5,355
74 6,651 6,039 5,427
75 6,740 6,120 5,500
76 6,829 6,200 5,572
77 6,918 6,281 5,645
78 7,007 6,362 5,717
79 7,096 6,443 5,790
80 7,185 6,523 5,862
81 7,274 6,604 5,935
82 7,363 6,685 6,007
83 7,452 6,766 6,080
84 7,541 6,846 6,152
85 7,630 6,927 6,224
86 7,719 7,008 6,297
87 7,808 7,089 6,369
88 7,897 7,169 6,442
89 7,986 7,250 6,514
90 8,075 7,331 6,587
91 8,164 7,412 6,659
92 8,253 7,492 6,732
93 8,342 7,573 6,804
94 8,431 7,654 6,877
95 8,520 7,735 6,949
96 8,609 7,815 7,022
channels
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels [Kbps]
97 8,698 7,896 7,094
98 8,787 7,977 7,167
99 8,876 8,058 7,239
100 8,965 8,138 7,312
101 9,054 8,219 7,384
102 9,143 8,300 7,457
103 9,232 8,380 7,529
104 9,321 8,461 7,601
105 9,410 8,542 7,674
106 9,499 8,623 7,746
107 9,588 8,703 7,819
108 9,677 8,784 7,891
109 9,766 8,865 7,964
110 9,855 8,946 8,036
111 9,944 9,026 8,109
112 10,033 9,107 8,181
113 10,122 9,188 8,254
114 10,211 9,269 8,326
115 10,300 9,349 8,399
116 10,389 9,430 8,471
117 10,478 9,511 8,544
118 10,567 9,592 8,616
119 10,656 9,672 8,689
120 10,745 9,753 8,761
channels
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Load Calculation for a HG 3500
3.2 Load Calculation for a HG 3500

Calculation of the high-priority load for a HG 3500
Protocol Data type Maximum bit rate/ port Total bit rate [Kbps] with
[Kbps] N payload ports
N=30 N=60 N=120
RTP VoIP 88.8 2,664 5,328 10,656
RTCP VoIP 0.2 6 12 25
Total load 2,670 5,340 10,681
Table 30 High-priority load of a HG 3500 (G.711/20 ms sample size)
In addition to high-priority load, low-priority load portions may also arise in certain
situations for the following:
• SNMP queries via network management
• TAP/Service PC access at the access point
• FTP-loading of a new HG 3575 loadware as a background task
High-priority load of a HG 3500 as a function of codec type and sample size
Codec Sample RTP load [Kbps] with Total Ethernet load [Kbps]
type size N payload ports with N payload ports
N=30 N=60 N=120 N=30 N=60 N=120
G.711 20 2,664 5,328 10,656 2,670 5,412 10,760
G.711 30 2,416 4,832 9,664 2,490 4,916 9,768
G.711 60 2,168 4,336 8,672 2,242 4,420 8,776
G.729A 20 984 1,968 3,936 1,058 2,052 4,040
G.729A 40 612 1,224 2,448 686 1,308 2,552
G.729A 60 488 976 1,952 562 1,060 2,056
Table 31 High-priority load of a HG 3500 as a function of codec and sample

size
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Note
This appraisal must be treated with caution, as the utility of the G.729A codec
is limited by various factors:
• The call is transferred uncompressed if one of the subscribers/circuits

involved prevents compression
• Connections with fax, modem and data terminal devices are only
transferred uncompressed
• External music and announcements are mostly transferred

uncompressed (depends on the configuration (RCSU-CLASSMRK))
• Connections to a conference unit are mostly switched without

compression (depends on the configuration (ZAND-IPDAVCCF))
In all of these cases, either G.711 is used, or no codec at all.
The bit rates for G.711 thus apply.

In order to guarantee that bandwidth bottlenecks are never encountered, the
access point link must be designed for the G.711 bit rate.
By means of statistical appraisals, taking the actual configuration into account

(how many fax/data devices are actually deployed, how many compression
licenses are available, are all possible subscriber/access circuits configured for
compression, how frequently are conferences used), a mixed calculation can be
performed.
The load as a function of a sample size can only be used if it is ensured that all
IPDA components are configured exclusively for this sample size. Otherwise, the
worst value for the respective codec type would have to be used for reasons of
reliability.
High-priority load of a HG 3500 as a function of the maximum number of B-

channels
Maximum Total Ethernet load at Total Ethernet load at Total Ethernet load at
permissible G.711/20ms G.711/30ms G.711/60ms
number of B- [Kbps] [Kbps] [Kbps]
channels
1 89 81 72
2 178 161 145
3 267 242 217
4 356 323 290
5 445 404 362
6 534 484 435
Table 32 High-priority load of a HG 3500 as a function of the permissible
number of B-channels
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels
7 623 565 507
8 712 646 580
9 801 727 652
10 890 807 725
11 979 888 797
12 1,068 969 870
13 1,157 1,050 942
14 1,246 1,130 1,015
15 1,335 1,211 1,087
16 1,424 1,292 1,160
17 1,513 1,373 1,232
18 1,602 1,453 1,305
19 1,691 1,534 1,377
20 1,780 1,615 1,449
21 1,869 1,696 1,522
22 1,958 1,776 1,594
23 2,047 1,857 1,667
24 2,136 1,938 1,739
25 2,225 2,019 1,812
26 2,314 2,099 1,884
27 2,403 2,180 1,957
28 2,492 2,261 2,029
29 2,581 2,341 2,102
30 2,670 2,422 2,174
31 2,759 2,503 2,247
32 2,848 2,584 2,319
33 2,937 2,664 2,392
34 3,026 2,745 2,464
35 3,115 2,826 2,537
36 3,204 2,907 2,609
37 3,293 2,987 2,682
38 3,382 3,068 2,754
39 3,471 3,149 2,827
40 3,560 3,230 2,899
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels
41 3,649 3,310 2,971
42 3,738 3,391 3,044
43 3,827 3,472 3,116
44 3,916 3,553 3,189
45 4,005 3,633 3,261
46 4,094 3,714 3,334
47 4,183 3,795 3,406
48 4,272 3,876 3,479
49 4,361 3,956 3,551
50 4,450 4,037 3,624
51 4,539 4,118 3,696
52 4,628 4,199 3,769
53 4,717 4,279 3,841
54 4,806 4,360 3,914
55 4,895 4,441 3,986
56 4,984 4,522 4,059
57 5,073 4,602 4,131
58 5,162 4,683 4,204
59 5,251 4,764 4,276
60 5,340 4,844 4,348
61 5,429 4,925 4,421
62 5,518 5,006 4,493
63 5,608 5,087 4,566
64 5,697 5,167 4,638
65 5,786 5,248 4,711
66 5,875 5,329 4,783
67 5,964 5,410 4,856
68 6,053 5,490 4,928
69 6,142 5,571 5,001
70 6,231 5,652 5,073
71 6,320 5,733 5,146
72 6,409 5,813 5,218
73 6,498 5,894 5,291
74 6,587 5,975 5,363
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels
75 6,676 6,056 5,436
76 6,765 6,136 5,508
77 6,854 6,217 5,581
78 6,943 6,298 5,653
79 7,032 6,379 5,725
80 7,121 6,459 5,798
81 7,210 6,540 5,870
82 7,299 6,621 5,943
83 7,388 6,702 6,015
84 7,477 6,782 6,088
85 7,566 6,863 6,160
86 7,655 6,944 6,233
87 7,744 7,024 6,305
88 7,833 7,105 6,378
89 7,922 7,186 6,450
90 8,011 7,267 6,523
91 8,100 7,347 6,595
92 8,189 7,428 6,668
93 8,278 7,509 6,740
94 8,367 7,590 6,813
95 8,456 7,670 6,885
96 8,545 7,751 6,958
97 8,634 7,832 7,030
98 8,723 7,913 7,103
99 8,812 7,993 7,175
100 8,901 8,074 7,247
101 8,990 8,155 7,320
102 9,079 8,236 7,392
103 9,168 8,316 7,465
104 9,257 8,397 7,537
105 9,346 8,478 7,610
106 9,435 8,559 7,682
107 9,524 8,639 7,755
108 9,613 8,720 7,827
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
channels
109 9,702 8,801 7,900
110 9,791 8,882 7,972
111 9,880 8,962 8,045
112 9,969 9,043 8,117
113 10,058 9,124 8,190
114 10,147 9,205 8,262
115 10,236 9,285 8,335
116 10,325 9,366 8,407
117 10,414 9,447 8,480
118 10,503 9,527 8,552
119 10,592 9,608 8,624
120 10,681 9,689 8,697
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
Calculation Basis - Configuring Payload Packets
3.3 Calculation Basis - Configuring Payload Packets
3.3.1 Configuring Ethernet MAC Frames
Table 33 Configuring Ethernet MAC frames for IPDA payload
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
3.3.2 Configuring IP Frames
Table 34 Configuring IP frames for IPDA payload
A31003-H3160-S104-8-7620, 07/2014
Load Calculation
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
Local Access Point Administration at CLI via Terminal
4 Local Access Point Administration at CLI via Terminal

If an LCT/service PC running “HiPath 4000 Expert Access“ is not available for the
local configuration of an access point, the administration may also be performed
directly via a terminal or terminal emulation, if necessary.
The RS 232 / V.24 interface at the 3575 is labeled with “Service“ and is set to
38400 Baud, 8 Bit, no Parity.
The Command Line Interface issues the following message after you press
= :
Please log in.
Username:
Login data
1. new board (before installation)
Login: HP4K-DEVEL
Password: 4K-admin
2. after installation (HiPath 4000 steuert NCUI4)

Login: TRM
Password: HICOM
If the module was already in operation and if the WBM login and password
were changed, then the values set apply.
The following is displayed after successful login:

Welcome to the HG 3575 V4.0 <LW-version> Command Line
Interpreter.
vxTarget>
After the prompt, the necessary parameters can now be entered.
A list of available commands can be now requested via the local help function
which is available via the help command.
The CLI does not distinguish between “direct link“ and “networked“ access points.
The designation of the parameters reflects the programming name of the
loadware. As already mentioned, direct operation of the CLI without the “HiPath
4000 Expert Access“ application is only an emergency solution.
The following tables are intended to assist in finding the correct content for the
parameters. The tables list the requisite CLI parameters and arrange them in
relationship to the AMO parameters from which the values have to be derived:
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
Networked access point
4.1 Networked access point
IMPORTANT: In order to be able to carry out the following commands, you will
need ADMIN rights in CLI.
CLI parameter Parameter meaning AMO - Branch - Parameter

name
ip_addr_eth IP address of the access point APRT
TYPE=APNET - APIPADDR
netmask_eth Netmask in the network of the access APRT
point TYPE=APNET - NETMASK
default_gateway IP address of the default router in the UCSU
network of the access point UNIT=AP - APRTADDR
ip_addr_signaling IP address of the access point APRT
TYPE=APNET - APIPADDR
netmask_signaling Netmask in the network of the access APRT
point TYPE=APNET - NETMASK
ip_addr_CC_A IP address of the CC-A SIPCO
TYPE=LSNET - CCAADDR
ip_addr_CC_B IP address of the CC-B SIPCO
TYPE=LSNET - CCBADDR
netmask_hhs HiPath 4000 LAN segment netmask SIPCO
TYPE=LSNET - NETMASK
vlan_tag VLAN tagging on/off STMIB: MTYPE=NCUI2,
[0 = OFF,1 = ON] TYPE=IFDATA - VLAN
vlan_id VLAN ID [0.. 4095] STMIB: MTYPE=NCUI2,
TYPE=IFDATA - VLANID
eth_link_mode Ethernet interface operating mode STMIB: MTYPE=NCUI2,
0 : Autonegotiation TYPE=IFDATA - BITRATE
21 : 10 Mbps half duplex AUTONEG: Autonegotiate
22 : 10 Mbps full duplex 10MBHD: 10 Mbps, half duplex
23 : 100 Mbps half duplex 10MBFD: 10 Mbps, full duplex
100MBFD: 100 Mbps, full duplex
Table 35 CLI parameter for “networked“ access point
Note
For “networked“ access points
• ip_addr_signaling = ip_addr_eth
and
• netmask_signaling = netmask_eth
must be set!
The command syntax is
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
Direct link access point
set ip address Parameter name Value or

set id Parameter name Value
For Access Point 99 from the configuration examples (see Figure 12 “HiPath
4000 LAN segment” and Figure 14 “Configuring a “networked“ access point” ),
the following command syntax is yielded:
get write access
set ip address ip_addr_eth 192.168.23.99
set ip address netmask_eth 255.255.255.0
set ip address default_gateway 192.168.23.1
set ip address ip_addr_signaling 192.168.23.99
set ip address netmask_signaling 255.255.255.0
set ip address ip_addr_CC_A 192.168.1.1
set ip address ip_addr_CC_B 192.168.1.1
set ip address netmask_hhs 255.255.255.0
set id vlan_tag 0
set id vlan_id 0
set id eth_link_mode 0
finish
IMPORTANT: No other commands (e.g. show) may be transmitted between the

set commands and the finish command, which transfers the data to the Flash
memory.
4.2 Direct link access point
IMPORTANT: In order to be able to execute the following commands, you will

need ADMIN rights in CLI.
CLI parameter Parameter AMO - Branch - Parameter

name
ip_addr_eth IP address of the access point in the UCSU
HiPath 4000 LAN segment UNIT=AP - LSRTADDR
netmask_eth HiPath 4000 LAN segment network SIPCO
mask TYPE=LSNET - NETMASK
default_gateway IP address of the default router in the UCSU
HiPath 4000 LAN segment UNIT=AP - APRTADDR
ip_addr_signaling IP address of the access point in the APRT
internal AP network segment TYPE=APNET - APIPADDR
netmask_signaling Netmask of the internal AP network APRT
segment TYPE=APNET - NETMASK
ip_addr_CC_A IP address of the CC-A SIPCO
TYPE=LSNET - CCAADDR
Table 36 CLI parameters for “direct link“ access point
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
Assignment of parameter names in LW-CLI to the AMO parameters
CLI parameter Parameter AMO - Branch - Parameter

name
ip_addr_CC_B IP address of the CC-B SIPCO
TYPE=LSNET - CCBADDR
netmask_hhs HiPath 4000 LAN segment network SIPCO
mask TYPE=LSNET - NETMASK
vlan_tag VLAN tagging on/off STMIB: MTYPE=NCUI2,
[0 = OFF,1 = ON] TYPE=IFDATA - VLAN
vlan_id VLAN ID [0.. 4095] STMIB: MTYPE=NCUI2,
TYPE=IFDATA - VLANID
eth_link_mode Ethernet interface operating mode STMIB: MTYPE=NCUI2,
0 : Autonegotiation TYPE=IFDATA - BITRATE
21 : 10 Mbps half duplex AUTONEG: Autonegotiate
23 : 100 Mbps half duplex 10MBFD: 10 Mbps, full duplex
100MBFD: 100 Mbps, full duplex
Table 36 CLI parameters for “direct link“ access point

The command syntax is
set ip address Parameter name Value or
set id Parameter name Value
For Access Point 17 from the configuration examples (see Figure 12 “HiPath
4000 LAN segment” and Figure 15 “Configuring a “Direct Link“ access point” ),
the following command syntax is yielded:
get write access
set ip address ip_addr_eth 192.168.1.17
set ip address netmask_eth 255.255.255.0
set ip address default_gateway 192.168.1.254
set ip address ip_addr_signaling 192.168.200.1
set ip address netmask_signaling 255.255.255.252
set ip address ip_addr_CC_A 192.168.1.1
set ip address ip_addr_CC_B 192.168.1.2
set ip address netmask_hhs 255.255.255.0
set id vlan_tag 0
set id vlan_id 0
set id eth_link_mode 0
finish
IMPORTANT: No other commands (e.g. show) may be transmitted between the

set commands and the finish command, which transfers the data to the Flash
memory.
4.3 Assignment of parameter names in LW-CLI to the AMO parameters

Finally, the following table provides an overview of all CLI parameters and their
assignment to AMO parameters.
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
Parameter name in Parameter name AMO Branch

LW-CLI
ip_addr_eth * APDL: LSRTADDR UCSU UNIT=AP
APNW: APIPADDR APRT TYPE=APNET
netmask_eth * APDL: NETMASK SIPCO TYPE=LSNET
APNW: NETMASK APRT TYPE=APNET
default_gateway *1 APRTADDR UCSU UNIT=AP
ip_addr_signaling * APIPADR APRT TYPE=APNET
netmask_signaling * NETMASK APRT TYPE=APNET
ip_addr_survivability *2 SURVNET (last byte SIPCO TYPE=LSNET
identical to 
LTU - UCSU)
netmask_survivability *2 fix: 255.255.255.0 - -
gateway_survivability *2 SURVNET (last byte SIPCO TYPE=LSNET
identical to ROUTERNO -
TYPE=SURV -APRT)
netmask_hhs * NETMASK SIPCO TYPE=LSNET
ip_addr_CC_A * CCAADDR SIPCO TYPE=LSNET
ip_addr_CC_B *3 CCBADDR SIPCO TYPE=LSNET
vlan_tag VLAN STMIB MTYPE=NCUI2
TYPE=IFDATA
vlan_id VLANID STMIB MTYPE=NCUI2
TYPE=IFDATA
eth_link_mode BITRATE STMIB MTYPE=NCUI2
TYPE=IFDATA
debug_details DEBUGDET STMIB MTYPE=NCUI2
TYPE=DEBUG
file_access_mode FACCMODE STMIB MTYPE=NCUI2
TYPE=DEBUG
server_port_signaling fix: 4000 - -
keep_alive_time_signal ALVTIME SIPCO TYPE=TIMING
reset_timer_sign_loss RESTIME SIPCO TYPE=TIMING
server_port_supervisory fix: 4001 - -
tos_lan TOSLAN STMIB MTYPE=NCUI2
TYPE=IFDATA
tos_modem TOSMODEM STMIB MTYPE=NCUI2
TYPE=IFDATA
survivability_enable *2 derived from - -
ip_addr_survivability >
0.0.0.0
Table 37 Assignment of parameter names in LW-CLI to the AMO parameters
* Requisite parameters for first-time initialization of NCUI2/4
A31003-H3160-S104-8-7620, 07/2014
04_hg3575_cli.fm
*1 Requisite parameters for first-time initialization of NCUI2/4 for “networked“ access

points
*2 Requisite parameters for first-time initialization of NCUI2/4 with signaling
survivability
*3 Requisite parameters for first-time initialization of NCUI2/4 at duplex systems
In the case of some parameters, a distinction must be made according to the type
of connection configured CONNTYPE - UNIT=AP - UCSU. In this case, different
assignments are required for APDL and APNW.
<LW-version>
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheets - IPDA Configuration
5 Spreadsheets - IPDA Configuration

The following spreadsheets are designed to help you perform an IPDA
configuration. Each of the sheets has a configuration diagram and a blank AMO
template on one side, and the completed example from the Service Manual on
the other.
The following spreadsheets (with example) are available:
• Spreadsheet: Configuring the HiPath 4000 LAN segment
• Spreadsheet: Configuring a “networked“ access point
• Spreadsheet: Configuring a “direct link“ access point
• Spreadsheet: Configuring HiPath HG 3500 as HG3570 in the HiPath 4000

system
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheet: Configuring the HiPath 4000 LAN segment
DEFRT
HG Peripheral
HG
STMI
AP
3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
Hi Path 4000 LA N Segme nt
3500 HG Peripheral
AP
3575 Boards
IP N e t wo r k
AP 3300 IP, AP 3500/3505
Peripheral
Boards NETADR
Ry HG Peripheral
NETMASK 3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP
CCAADR HG Peripheral
3575 Boards
AP
CC-A R1
Router P ST N N e t wo r k AP 3300 IP, AP 3500/3505
CCBADR SURVNET
3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000
ADD-SIPCO: NETADDR= . . . NETMASK= . . . ,

,
DEFRT= . . . , CCAADDR= . . . ,
CCBADDR= . . . SURVNET= . . .0;
,
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Sample Sheet: Configuring the HiPath 4000 LAN segment
DEFRT
HG
STMI
AP
3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
Hi Path 4000 LA N Segme nt
3500 HG Peripheral
AP
3575 Boards
IP N e t wo r k
AP 3300 IP, AP 3500/3505
Peripheral
Boards
NETADR
192.168.1.0 Ry HG Peripheral
NETMASK 3575 Boards
AP
Router
255.255.255.0 AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP
CCAADR HG Peripheral
3575 Boards
AP
192.168.1.1
CC-A R1
Router P ST N N e t wo r k AP 3300 IP, AP 3500/3505
CCBADR SURVNET
192.168.1.2 192.168.15.0 HG
CC-B R10 Peripheral
3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000
ADD-SIPCO: NETADDR=192.168.1.0, NETMASK=255.255.255.0,

DEFRT=192.168.1.254, CCAADDR=192.168.1.1,
CCBADDR=192.168.1.2, SURVNET=192.168.15.0;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheet: Configuring a “networked“ access point
LSRTADR APIPADR
HG Peripheral
HG
STMI
AP
3575 Boards
3500
Ra Rx AP 3300 IP
Router Router
HG
STMI
AP 98
H iPat h 400 0 LA N Segment
APRTADR 3575 Boards
AP 3300 IP, AP 3500/3505

Peripheral
Boards NETMASK
Ry HG Peripheral
AP ,
Router 3575 Boards
AP 3300 IP, AP 3500/3505

ADP
Atlantic LAN
HG Peripheral
3575 Boards
AP
CC-A R1
Router AP 3300 IP, AP 3500/3505
PS T N N e t wo r k
AP ,
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000
ADD-UCSU: UNIT=AP, LTU= ,

LTPARTNO=Q23 -X , SRCGRP= ,
FRMTYPE= , CONNTYPE=APNW,
LSRTADDR= . . . , APRTADDR= . . . ,
LOCID= , LOCATION=“
“,
PHONE= , FAX= ,
PLCHECK= , BCHLCNT= ,
CONVLAW= ;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
ADD-APRT: TYPE=APNET, LTU= ,

APIPADDR= . . . , NETMASK= . . . ;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Sample Sheet: Configuring a “networked“ access point
LSRTADR APIPADR
AP 99
192.168.1.254 192.168.23.98 HG Peripheral
HG
STMI
3575 Boards
3500
Ra Rx AP 3300 IP
Router Router
HG
STMI
AP 98
H iPat h 400 0 LA N Segment
APRTADR 3575 Boards
192.168.23.1
AP 3300 IP, AP 3500/3505
Peripheral
Boards NETMASK
255.255.255.0
Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP
AP 18
HG Peripheral
3575 Boards
CC-A R1
Router AP 3300 IP, AP 3500/3505
PS T N N e t wo r k
AP 17
3575 Boards
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000

LTPARTNO=Q2305-X35, SRCGRP=2,
FRMTYPE=AP 9837009, CONNTYPE=APNW,
LOCID=2, LOCATION=“BLN ROHRDAMM
85. GEB. 30-222“,
PHONE=03038612345, FAX=03038654321,
CONVLAW=NO;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm

A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheet: Configuring a “direct link“ access point
APRTADR
HG Peripheral
HG
STMI
3575
AP
Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
3500 I P N et wor k HG Peripheral

H iPat h 40 00 LA N Segmen t
AP
3575 Boards
AP 3300 IP, AP 3500/3505

Peripheral
Boards
Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP NETMASK
AP 18
HG Peripheral
3575 Boards
CC-A R1 APIPADR
Router AP 3300 IP, AP 3500/3505
PS T N N e t wo r k
CC-B R10 LSRTADR HG Peripheral
AP
Router 3575 Boards
AP 3500 IP
CC-A
Assistant
HiPath
4000
ADD-UCSU: UNIT=AP, LTU= ,

LTPARTNO=Q23 -X , SRCGRP= ,
FRMTYPE= , CONNTYPE=APDL,
LSRTADDR= . . . , APRTADDR= . . . ,
LOCID= , LOCATION=“
“,
PHONE= , FAX= ,
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
PLCHECK= , BCHLCNT= ,
CONVLAW= ;
ADD-APRT: TYPE=APNET, LTU= ,
APIPADDR= . . . , NETMASK= . . . ;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Sample Sheet: Configuring a “direct link“ access point
APRTADR
HG
STMI
3575
AP
Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
3500 I P N et wor k HG Peripheral

H iPat h 40 00 LA N Segmen t
AP
3575 Boards
AP 3300 IP, AP 3500/3505

Peripheral
Boards
Ry
AP 43
HG Peripheral
Router 3575 Boards
AP 3300 IP, AP 3500/3505

Atlantic LAN
ADP NETMASK
255.255.255.252
AP 18
HG Peripheral
3575 Boards
CC-A R1 APIPADR
Router 192.168.200.1 AP 3300 IP, AP 3500/3505
PS T N N e t wo r k
AP 17
CC-B R10 LSRTADR HG Peripheral
192.168.1.17 3575 Boards
Router
AP 3500 IP
CC-A
Assistant
HiPath
4000

LTPARTNO=Q2302-X10, SRCGRP=1,
FRMTYPE=INCH19, CONNTYPE=APDL,
LOCID=1, LOCATION=“MCH
MACHTLFINGERSTR.1 GEB.
7202-111“,
PHONE=08972223456, FAX=08972265432,
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
CONVLAW=NO;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheet: Configuring HiPath HG 3500 as HG3570 in the HiPath 4000

system
IPADR HG Peripheral
HG
STMI
AP
3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
3500 HG Peripheral
HiPat h 4000 LAN Segment
AP ,
3575 Boards
IP Networ k
AP 3300 IP, AP 3500/3505
Peripheral
Boards
Ry HG Peripheral
3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP
HG Peripheral
3575 Boards
AP
CC-A R1
Router PSTN Networ k AP 3300 IP, AP 3500/3505

3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000
ADD-BFDAT: FCTBLK= , FUNCTION=HG3570,

BRDBCHL= ;
CHANGE-BFDAT: CONFIG=CONT, FCTBLK= ,
FUNCTION= , BCHLCNT= ;
CHANGE-BFDAT: CONFIG=OK, FCTBLK= ,
ANSW= ;
ADD-BCSU: MTYPE=IPGW, LTU= ,
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
SLOT= , PARTNO=Q23 -X ,
FCTID= , FCTBLK= ,
IPADR= . . . , BCHL3570= ;
CHANGE-BCSU: TYPE=HWYBDL, LTU= ,
SLOT= , PARTNO=Q23 -X ,
HWYBDL=A;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Sample Sheet: Configuring HiPath HG 3500 as HG3570 in the HiPath 4000

system
IPADR
HG
STMI
AP
3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router
HG
STMI
3500 HG Peripheral
HiPat h 4000 LAN Segment
AP ,
3575 Boards
IP Networ k
AP 3300 IP, AP 3500/3505
Peripheral
Boards
Ry HG Peripheral
3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP
HG Peripheral
3575 Boards
AP
CC-A R1
Router PSTN Networ k AP 3300 IP, AP 3500/3505

3575 Boards
AP
Router
AP 3300 IP, AP 3500/3505
CSTA
Assistant
HiPath
4000

BRDBCHL=BCHL60&BCHL120
;
FUNCTION=HG3570, BCHLCNT=40;
ANSW=YES;
ADD-BCSU: MTYPE=IPGW, LTU=5,
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
FCTID=1, FCTBLK=1,
IPADR=192.168.1.11, BCHL3570=40;
CHANGE-BCSU: TYPE=HWYBDL, LTU=5,
HWYBDL=A;
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
A31003-H3160-S104-8-7620, 07/2014
06_info_netw_admin.fm
Information for network administrators
Central Processor
6 Information for network administrators
6.1 Central Processor

Every central processor receives an additional LAN interface for controlling
access points when an IPDA system is installed.
PHY 1GBit - autosensing or can be permanently set

MAC address Permanently programmed on the interface card, -
>sticker
IP address Configured in the HiPath 4000 system, can be set
IEEE 802.1 p/q VLAN tagging Configurable; priority bits are always set when active.
See Table 3 “TOS values” in document “Gateways
HG 3500 and HG 3575”.
The VLAN ID can be set. Configuration in the HiPath
4000 system.
TOS/DiffServ The six highest bits in the TOS byte can be set. See
Table 3 “TOS values” in document “Gateways HG
3500 and HG 3575”. Configuration in the HiPath 4000
system.
Protocols/ports See Chapter 21, “IP Ports” in the document
“Gateways HG 3500 and HG 3575”.
Routing A host route that is configured in the HiPath 4000
system is used to every access point. No default
route.
Firewall The central processor only allows connections to
addresses that it knows, i.e. access points or
assigned service PCs.
Number of connections Up to 166 TCP/IP connections (two per access point)
In large systems, two redundant central processors are installed, one of which is
always active. Every processor has its own IP network connection with its own
IP and MAC address. PHY is active in the standby processor. However, the
standby processor does not receive and send packets.
6.2 HG 3500 Voice Gateway
IMPORTANT: IP packets with the used ports (hard-coded and configured using
AMOs) must be routed transparently in the IP network, i.e. the packets must be
unmanipulated, e.g. by a firewall). Functional problems can be the result of non-
transarent routing!
A31003-H3160-S104-8-7620, 07/2014
Access Points with HG 3575
These boards are installed in the HiPath 4000 central system. A maximum of 83
HG 3500 boards can be configured in a system.
PHY 10/100 Base T - autosensing or can be permanently

set
MAC address Permanently programmed on the board, ->sticker
IP address Configured in the 4000 system, can be set. It must be
in the same network segment as the central
processor.
The address is assigned to the slot in the system.
When a board is exchanged, the new one
automatically adopts the IP address.
See Table 3 “TOS values” in document “Gateways HG
3500 and HG 3575”.
4000 system.
system.
Protocols/ports See Chapter 21, “IP Ports” in the document
“Gateways HG 3500 and HG 3575”.
Routing Routing table configured in the HiPath 4000 system
with a default route and up to eight additional routes.
Routing is identical for all HG 3500s in the system.
Number of connections Up to 30/60/120 RTP and RTCP connections to any
access points, depending on the hardware used.
Connection setup controlled completely from HiPath
4000. H.323 Fast Connect for direct media
connections outside the IPDA gateway network, no
gatekeeper necessary.
See Section 3.2, “Load Calculation for a HG 3500” for
connection bandwidths.
6.3 Access Points with HG 3575

An HG 3575 is used as the central board for each access point. Access points are
only connected to the central system via IP. A maximum of 83 access points can
be configured in a system.
As regards addresses, a distinction must be made between “networked“ and

“direct link“ access points.
“Networked“ access points are in a different network segment to the central

system and can therefore only be reached via a router.
A31003-H3160-S104-8-7620, 07/2014
Access Points with HG 3575
“Direct Link“ access points are connected in the same network segment as the
central system.
The HiPath 4000 system is used for configuring addresses and the port settings.
The access point is stored locally. The parameters must be set locally for initial
startup.
PHY 10/100 Base T - autosensing or can be permanently set

IP addresses See below
IEEE 802.1 p/q  Configurable; priority bits are always set when active. See
VLAN tagging Table 3 “TOS values” in document “Gateways HG 3500 and
HG 3575”.
The VLAN ID can be set. Configuration in the HiPath 4000
system.
TOS/DiffServ The six highest bits in the TOS byte can be set. See Table 3
“TOS values” in document “Gateways HG 3500 and HG
3575”. Configuration in the HiPath 4000 system.
Protocols/ports See Chapter 21, “IP Ports” in the document “Gateways HG
3500 and HG 3575”.
Routing Routing table configured in the HiPath 4000 system with a
default route and up to eight additional routes. Routing can be
individually set for the access point.
Number of connections Up to 30/60/120 RTP and RTCP connections to any HG 3500
or access points.
Connection setup controlled completely from HiPath 4000.
H.323 Fast Connect for direct media connections outside the
IPDA gateway network, no gatekeeper necessary.
Up to two TCP/IP connections to the central processor.
When using AP Emergency features and a TCP/IP
connection to the survivability unit.
See Section 3.1, “Load Calculation for Access Points” for
connection bandwidths.
IP addresses for “networked“ access points:
IP address For signaling, payload, SNMP, FTP, Telnet.

of the access point See Figure 13 “Difference between “networked“ and “direct
link“ access point”
Address must be routed in the network.
IP address This address remains invisible in the LAN as it is only used
for signaling survivability for the PPP connection between the survivability router and
modem connection of the access point.
This address is assigned indirectly by configuring the
network address for the virtual survivability network (PPP
via ISDN). Only a “private“ address such as 192.168.x.0
should be used here.
A31003-H3160-S104-8-7620, 07/2014
IP address for “direct link“ access points:
IP address For payload, SNMP, FTP, Telnet, however not for signaling.
of the access point See Figure 13 “Difference between “networked“ and “direct
link“ access point” . Address must be in the same network
segment as the central processor.
Address must be routed in the network.
IP address The signaling connection between the central processor
for signaling and the access point must pass via a router. See Figure 13
“Difference between “networked“ and “direct link“ access
point” .
If the LAN connection fails, the current TCP connection is
rerouted for signaling survivability. This can only be
performed by changing the router whereas the destination
address remains the same.
An internal router which routes between the access point IP
address and the internal address of the signaling instance
is therefore used for “direct link“ access points.
The IP address for signaling must be in a separate “private“
network segment. It is visible in the LAN (using a sniffer) as
the destination address of the signaling packet.
However, as signaling packets are routed exclusively from
the central processor to the access point IP address via the
host route, no router needs to/must route this address in the
LAN.
Only a “private“ address such as 192.168.x.0 should be
used here.
IP address This address remains invisible in the LAN as it is only used
for signaling survivability for the PPP connection between the survivability router and
modem connection of the access point.
This address is assigned indirectly by configuring the
network address for the virtual survivability network (PPP
via ISDN). Only a “private“ address such as 192.168.x.0
should be used here.
IMPORTANT: Only possible if HG 3500 is configured without WAML function!
Feature requirement
For increased resilience, HG 3500 and HG 3575 boards should be connected
with two LAN cables to different switches.
Feature functionality
• Board is starting up:
A31003-H3160-S104-8-7620, 07/2014
If both LAN cables are connected and the HG board is starting up, LAN port
1 will always be activated.
LAN port 2 will be on standby, only layer 1 is active (higher protocol layers are
down).
If only one LAN port is connected when the board is starting up (LAN1 or
LAN2), that port will be used.
• If the active LAN port is disconnected/disabled by peer or equipment (when

both LAN ports are connected):
– The boards activate the standby LAN port.
– The “new” port sends a GRATUITOUS ARP with the same MAC and IP
addresses as the “old” port (the second MAC address will only be used if
also another feature is configured at the interface (WAML/PPP router)).
– When the board switches ports, the payload will be lost for < 2 sec – all
active connections will be saved and NOT disconnected.
– The port switch will be logged via HiPath-4000-F message in HISTA.
– If the “old” port comes up again, no port switchback will be performed.
Restriction
If the board is configured with FUNCTION=WAML in the AMO BFDAT, LAN port
1 is unable to switch over to LAN port 2 in the event of a fault.
This is because the feature WAML2/WAML Replacement is used for signaling

survivability. This prevents the STMI board used from even operating redundant
LAN interfaces.
Notes
• The boards only have one IP and MAC address.
• Only one port is active at a time.
• When the board starts up with two connected ports, LAN1 will be activated.
• No port switchback will be performed.
• No configuration in HiPath 4000 / HG boards is necessary to activate the

feature.
• After installation of redundant LAN feature it is recommended to verify the

functionality. The test can be performend by unplug the activ LAN cable for at
least 5 seconds and observe the switchover.
The reason for the test is to verify the correct beahaviour of HG3500 in
interaction with redundant IT/LAN infrastructure (e.g. L2 Switches/Router).
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
07_ipda_wizard.fm
IPDA Wizard
Functions
7 IPDA Wizard
The IPDA Wizard provides a step-by-step user interface to help you with IPDA
and HiPath 4000 SoftGate configuration.
You will find the wizard under:
Configuration Management > IPDA Wizard
Figure 44 IPDA Wizard - Start page
7.1 Functions
You can add or change the following IPDA components:
• IPDA System Parameter

The following functions are available:
• Configure System IP Addresses

IP addresses of the HiPath 4000 LAN segment, central processors, and
the default router of the HiPath 4000 LAN segment.
• Configure Network Paraeters

Parameters used for transmission bitrate, VLAN tagging and quality of
service parameters are configured here.
• Configure Payload Quality Thresholds
A31003-H3160-S104-8-7620, 07/2014
07_ipda_wizard.fm
IPDA Wizard
Functions
Configure thresholds (e.g. timers) used to monitor transmissin quality on

a connection.
• HG 3570 Boards (Create or Modify HG 3570 Boards)
• Access Points (Create or Modify HG 3575 Modules)

With this function you can configure new access points/HiPath 4000
SoftGates or modify existing access points/HiPath 4000 SoftGates. It is also
possible to configure a new access point/HiPath 4000 SoftGate by using an
already existing access point/HiPath 4000 SoftGate as template.
Result Access Point:
• AMO batch
• CLI batch (for configuring the NCUI board in the AP)

Result HiPath 4000 SoftGate:
• AMO batch
• xml file (for configuring the HiPath 4000 SoftGate)
• Survivability Routing (Payload and Signaling)

Here you can configure alternate routes for the Signaling and payload
conncetions to be used in case the IP network fails.

With Access Point Emergency, additional control processors at access points
(CC-AP) are deployed, which can take over control of a group of access
points when these acess points have lost connection to the host control
processors (CC-A, CC-B) due to network failure or failure oft he host system
itself.
The following fucntions are available:
• Configurre a local CC for an access point
• Configure a control processor located in an access point, which will be

used in emergency situations.
• Configure an emergency group

Configure emergency group specific data, i.e. criteria for switching to
ermegency mode resp. back and the control processor to be used.
• Assign an access point to an emergency group

Here you can assign an individual access point to the emergency groups
defined before or change the influence of this AP for switching the group
to emergency mode.
• Configure alternate routing for emergency
A31003-H3160-S104-8-7620, 07/2014
07_ipda_wizard.fm
IPDA Wizard
Functions
Configure an alternate CO routeper ource group, which will be used in

emergency situations.
• System Initialization
You can perform the following under System Initialization
• Reset of Boards
Reload of HG3570 boards and/or access points.
• Loadware and SIU Files onto Access Points

Load new loadware onto access points.
• System Restarts
Execute Soft- or System-Restart on the HiPath 4000 Switch.
• Switch Systemmode
Switch a system unit to emergency or normal mode.
Button “Overview”
Additionally the assistant provides a graphical overview of the current IPDA
configuration.
Figure 45 IPDA Wizard - Graphical overview of the currenct IPDA configuration
A31003-H3160-S104-8-7620, 07/2014
07_ipda_wizard.fm
IPDA Wizard
Functions
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
FAQs - Frequently Asked Questions
8 FAQs - Frequently Asked Questions

1. Question: Do I actually need a HG 3500 board in the central system for every
AP 3300 IP or AP 3500 IP access point?
Answer: NO, definitely not. It is always assumed that there must be a fixed
relationship between a HG 3575 and a HG 3500 to transfer signaling data.
However, signaling data comes directly from the central processor (via the SL
200 or SL 100 module). The HG 3500 is only responsible for payload
transport. 
The number of HG 3500s required in the system depends solely on the traffic
volume between the access points (total for all APs) and the central system.
2. Question: How can I ensure that a HG 3500 crash does not automatically
affect associated access points?
Answer: HG 3500s are not allocated to any specific access points. If there
are several HG 3500s in the system, then they share the overall traffic
volume. HG 3500 seizure is performed cyclically in the system, i.e. the first
connection is routed via the first HG 3500, the next via the second and so on.
If an HG 3500 fails, all active calls over this board are interrupted. The board
is then no longer seized for new calls. These new calls are then routed via
the other HG 3500s, as capacity allows.
3. Question: Why are IPDA components not allowed to be connected via hubs?
Answer: Hubs work in Ethernet’s classic “shared medium“ mode. All
connected units share the total bandwidth. Jeder kann alles mithören. Nur
einer kann zu einem Zeitpunkt senden.
Voice communication is bidirectional. The data flow from A to B is the same
size (expect using VAD) as the dataflow from B to A. As transmission is only
possible from one unit at a time in shared medium mode, the send and
receive direction each occupy the same share of the total bandwidth
available.
The use of layer 2 switches, which are nowadays often cheaper than hubs,
decouples the connection media of the individual units. All units can
simultaneously send and receive. The bandwidth (now available for each
unit) can be used more efficiently.
4. Question: Why are the LAN ports on the IPDA components set by default to
Autonegotiate? There are many reports that this can lead to problems.
Answer: The default setting should ensure that initial startup runs relatively
smoothly. However, on account of the recurring problems encountered with
autonegotiation, we strongly urge you to enter a fixed setting for both
interface partners. 
It is essential to configure both interfaces - with the same values - at the same
time. When using an autonegotiate interface with one that is fixed, the
autonegotiate interface often fails to “negotiate“ to the fixed interface’s
setting. Please also refer to the Note on page 578.
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
5. Question: Is it necessary to enter the network address for the HiPath 4000
LAN segment in the AMO SIPCO? Does every HiPath 4000 need a separate
LAN segment or can I operate multiple HiPath 4000 systems in the same LAN
segment?
Answer: You can operate multiple HiPath 4000 systems in the same network.
In this case, the components’ IP addresses must not be used more than once
and the capacity of the router or WAN connection must suffice for the entire
bandwidth requirement.
6. Question: The effect of default setting recommended by popular router

manufacturers and the TOS byte default values documented for IPDA, that is,
the pre-defined DiffServ CodePoints (DSCP) is exactly the opposite of the
intended effect. The packets we marked as high priority are rejected
straightaway by the router. What is this nonsense about?
Answer: The default values used for IPDA come from an internal standard
that was implemented in all HG 35xx gateways. The interoperability problem
has since come to light with the result that the company standard will be
modified shortly.
The default values can be modified at any time and modified in line with actual
conditions in the customer network.
7. Question: Does IPDA support VLANs?

Answer: Yes but only in conjunction with priority tagging. In accordance with
IEEE 802.1 p/q, tagging was introduced for IPDA to support priority tagging.
If tagging is activated then the permanently preset priority bits of the various
types of traffic are always set (see the last column of Table 3 “TOS values” in
document “Gateways HG 3500 and HG 3575”). If tagging is active, the VLAN
ID can also be set (default value is zero). VLAN ID is not supported without
the set priority bits.
8. Question: Does IPDA support subnetting (RFC 950)?

Answer: Yes. When the network mask is entered, a check is performed to
determine whether the block of ones that has been set meets the minimum
length required for the class of the address, i.e. 8 ones for Class A, 16 for B
and 24 for C. If the number of ones is greater than the number required for
the class, subnetting is activated.
9. Question: Does IPDA support supernetting (RFC 1338)?

Answer: No.
10. Question: Can an access point be operated such that signaling is only
routed via IP? Voice can be routed as a dial-up connection via ISDN as in the
case of payload survivability.
Answer: Payload survivability is designed as an emergency solution in the
event of an IP network crash/malfunction. Only basic call functionality can be
guaranteed.
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
You must also take into consideration that signaling via IP must offer Quality
of Service which is often not supported when using external narrowband
WAN links together with data communication in existing installations.
Follow-up question: It cannot be that difficult for an ISDN PABX to route
voice connections via a carrier network.
Answer: The systems are designed for it. However, in the case described
above, the system must call itself via the CO and negotiate this as an
internal call with the complete range of features - and this in itself is not
an easy task.
11. Question: Why does the “direct link“ access point need additional IP
addresses? 
It must be easier to route a call in the same LAN segment than in multiple LAN
segments with routers.
Answer: The reason for the internal router and the additional address is due
to signaling survivability. For signaling survivability, TCP layer packets which
can no longer be transported via LAN must be delivered on another route,
that is, the survivability path, before the supervision timer in the TCP expires.
The IP destination addresses must remain the same for this, only the router
involved can be switched.
In the case of a “networked“ access point, the (default) LAN router is switched
to the survivability router.
This LAN router is not available in the case of a “direct link“ access point, as
CC and AP are in the same LAN segment. You cannot switch from no router
to a survivability router. Consequently, signaling survivability could not be
offered for “direct link“. The only practical solution is to integrate the LAN
router in the access point. Two IP addresses are therefore provided for a
“direct link“ access point: the router port IP address at the HiPath 4000 LAN
segment and the signaling instance IP address in the AP “internal network“.
12. Question: Is it possible to operate the IPDA components in a network that

does not support Quality of Service?
Answer: If the entire network is ideally dimensioned, if there is no packet loss
and no significant packet propagation time during long-term measurements
and if the network load (including the IPDA load) is moderate on all paths,
then an IPDA system will also function in this network without QoS measures.
Malfunctions will occur if these conditions are violated, for example, through
load displacement or something similar. Constant, highly developed network
monitoring is essential in this case to recognize bottlenecks developing in the
network and to remove them immediately.
If narrowband WAN connections which are also used for data connections
and have a high load are utilized in the network used for IPDA, then
malfunctions are guaranteed in networks without a QoS functionality for
prioritizing IPDA traffic.
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
13. Question: A remote access point is connected via WAN. Transmission

capacity is only 800 Kbps. Major interferences occur during peak traffic and
the access point sometimes performs restarts. The traffic from/to the access
point is prioritized higher compared to parallel, active data traffic. Can the
bandwidth seized by HiPath 4000 on the WAN link be limited to 800 Kbps?
Answer: The bit rate required by the access point can be limited by the
Resource Manager. Table 29 “High-priority load of an AP as a function of the
permissible B-channels” provides an overview of the capacity required as a
function of the number of connections simultaneously active. The basis for
this assumption is calls using the G.711 codec. The signaling load was set to
64 Kbps. With a sample size of 30 ms (default), nine connections could be
used simultaneously to remain under 800 Kbps (792).
Follow-up question: Table 28 “High-priority load of an AP as a function
of codec and sample size” shows me that I can transport significantly
more B-channels with the available bandwidth if I use the G.729 codec.
Answer: The 800 Kbps available could theoretically transport over 30 B
channels if the sample size were set to 40 ms in G.729.
However, please note that in this case, all the trunks in the entire system
involved in calls must be configured to support G.729 (classmark
G729OPT). This is the default setting. All trunks in the access point must
also be configured with classmark G729 which necessitates the use of the
G.729 codec. This also applies to the conference connection and music-
on-hold.
However, we advise against configuring the conference unit with G.729 if
you want to guarantee the best voice comprehension levels possible for
conferences. 
It should also be noted that the melody played back when music-on-hold
is active is distorted by the voice compression.
In addition, please note that fax machines, modems and ISDN data
terminals must not operate with G.729 compression. If these devices are
active, 81 Kbps will be seized (30 ms - in this example - with G.711 and
40 ms with G.729) instead of the anticipated 21 Kbps. 
In other words, the number of B channels in this example must not be set
to 30 even with the maximum possible use of G.729. The correct value is
between 9 and 30. It depends on how many G.711 connections are still
required. 
If the number of B channels is set too high, ALL connections will be
affected when the capacity of the WAN link is exceeded. The signaling
connection can also be affected and can, depending on the level of
interference, cause a switchover to signaling survivability or an access
point restart.
14. Question: I’d like to dispatch an access point over ISDN. Given that NCUI
only provides a LAN connection, I’d like to use a router with an S0 interface.
This offers me a bandwidth of 128 Kbps, which is enough for 7 B channels. I
estimate the signaling volume to be very low. Should I expect any problems?
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
Answer: Yes, you should stay well clear of this configuration. Although 7 B
channels require only 114 Kbps with G.729 compression and a sample size
of 60 ms, there is good reason for always keeping around 64 Kbps free for
signaling. This leaves only around 64 Kbps for payload. That is not sufficient,
even if only one call cannot be compressed (fax, modem, ISDN data). See
also Question 13.
15. Question: I’d like to use a PCM30 router between an access point and
HiPath 4000 LAN segment, thus with a maximum of 2 Mbps of bandwidth
available.
However, because the customer wants to use dial-up lines through the public
telephone network instead of dedicated circuits, the actual bandwidth should
be kept as small as possible and only adapted/increased as required. As a
minimum, we would provide one channel for the required 64 Kbps signaling.
Should I expect any problems?
Answer: Yes, having “dynamic“ WAN bandwidth will cause problems that can
only be resolved with fixed bandwidth. The reason for this is very simple. Let’s
assume that the amount of bandwidth currently available is exactly right. Now
a call comes through. There is therefore no longer enough bandwidth
available. What does the router do? Firstly, it blocks the packets that it can no
longer get rid of due to the lack of bandwidth, which affects all connections
equally. If the backlog is not cleared within a specific time, it establishes a
second 64 Kbps connection in the telephone network. Once connection setup
has been completed, there is once again enough bandwidth available. (If not,
a further 64 Kbps are set up.) This requires only a few seconds. During this
time, all payload connections are affected as is - if not protected by means of
prioritization - the signaling connection.
16. Question: How can I check the actual Quality of Service available at an
access point? The network operator says that everything is in order. The
telephone subscribers complain about sporadic low voice comprehension.
Answer: The QoS values recorded with the real-time transmission protocol
can be checked via SNMP at all HG 3575 and HG 3500 boards. See Chapter
20, “SNMP Support HG 3500 / HG 3575” in the document “Gateways HG
3500 and HG 3575”.
HiPath 4000 Assistant also features an option for recording, evaluating and
displaying QoS parameters on a call-by-call basis. See HiPath 4000
Assistant -> Diagnose -> IPDA Service Access -> Call Quality Recording
Viewer, MIB Viewer or QoS Viewer
Follow-up question: According to the network operator, not a single IP
packet was lost during the period when there were problems with voice
communication. Is there another possible cause for poor voice quality?
Answer: If the network operator delivers packets with a delay greater
than the size of the jitter buffer, they are not available for the codec when
they are needed. This means that although the packets are being
delivered correctly from the network operator’s point of view, they are lost
in the real time context of voice transmission.
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
17. Question: Fax and data via Voice over IP connections are very critical. How
well does this really work?
Answer: There are three factors that are relevant here: packet loss, jitter and
delay. 
Modern voice codecs provide acceptable voice quality even with a packet
loss of 5% through procedures such as “packet loss concealment“. 
The packet loss cannot, however, be disguised in the case of fax, modem or
ISDN data connections. The throughput declines here due to the number of
retransmissions necessary. If packet loss is too high, the connection is
cleared down by the terminals.
Jitter causes indirect packet loss. Jitter buffer dimensioning is important here.
This should be dimensioned as small as possible to keep delays short.
However, packets whose deviation from “normal“delays can no longer be
compensated for in the jitter buffer are lost.
The total number of packets lost in the network or due to high jitter levels
should be significantly higher for voice then for fax, modem and data.
To satisfy the various traffic type requirements in terms of jitter-specific packet
loss (voice < 5%, fax, modem data ~0%), the jitter buffer value set for fax,
modem or data connections is increased by 30 ms in the HiPath 4000
components HG 3500 and HG 3575.
The delay on the connection can - depending on the data transfer protocol
used - also be critical. If transmission is subject to acknowledgement, the
acknowledgement is delayed by the transmission delay which reduces the
throughput in contrast to undelayed connections.
The signal processors evaluate the signaling tones from the connected fax or
modem devices when setting up a connection. A distinction is made here
between high- and low-speed devices and transmission is optimized
accordingly.
18. Question: What bit rates are guaranteed by IPDA for fax devices or
modems?
Answer: IPDA is unable to guarantee bit rates higher than those ensured by
the HiPath 4000 central system. That is 14.4 Kbps. Higher bit rates lead to
dependencies on the attenuation plan, the attenuation set at the T reference
point, etc. Bit rates above 14.4 Kbps are technically possible in particular
constellations but cannot be guaranteed.
19. Question: The customer uses an all-in-one device (printer/scanner/modem

combo) as a fax machine. Fax connections to conventional fax devices work
perfectly. Faxes from identical devices within the IPDA system, however,
cause problems.
Answer: Problem are caused by all-in-one devices that want to improve the
transmission speed above and beyond the fax standard. These devices enter
the negotiation phase at the start of the fax connection as “normal“ Group 3
fax devices. If they both determine that they both support a proprietary - and
faster - transmission method, then they use it. 
The IPDA gateway problem is like the problem that occurs on remote links.
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
The transmission path is optimized on the basis of the signaling tones that
indicate a low bit-rate connection. But the devices decide to use a
transmission method with a high bit rate during negotiation. And that causes
problems with the path optimized for low bit-rate transmission.
20. Question: The Service Manual makes repeated references to the pinging of
IP addresses for the IPDA components. I’m now doing it, and it only works
sometimes or not at all.
Answer: There are three factors that influence a successful ping
• The ping request must reach the destination in order to obtain a response.
For this to happen, the routing from the port of the computer that sends
the ping to the destination must be safeguarded. It is therefore important
that ping requests come from the IPDA components and not from any
other devices on the network (service PC on AP or from Assistant).
• The ping request must not be rejected by a firewall at the destination.

The control processors CC-A/CC-B protect themselves from floods of
ping requests by allowing only a specific volume of requests per unit of
time. The filter is set up so that a standard ping command with
approximately 5 requests in intervals of about one second can be
responded to without any problems. However, requests that are more
frequent or at shorter intervals are rejected.
Please note also that ping requests are only answered by the currently
active processor.
• The ping response must come back to the requestor to be analyzed.

For this to happen, the routing from the pinged IPDA component to the
computer that sent the ping must be safeguarded. 
The control processors CC-A/CC-B use only host routes to the configured
devices (in other words, no general route to the networks on which the
devices are connected) and have no default router in the HiPath 4000
LAN segment.
21. Question: I have, on a number of occasions and in different error scenarios,

exchanged the NCUI boards “cross-wise“. The error is always repeated. This
can’t be right, can it?
Answer: With the NCUI, cross-wise exchange is very problematic because
the local configuration data needs to be changed.
If you just exchange the modules without reconfiguring them, you take the
LTU number and the entire configuration of the shelf as well. The central
system accesses LTU 17 with the configured IP address. If the NCUI module
with this address now actually sits in another shelf, this is now LTU 17.
You should therefore follow the instructions in Section 2.2.9, “Information on
Exchanging HG 3575 Boards” of the Service Manual when exchanging
modules. Cross-wise exchange is also a module exchange. 
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
This involves applying the local configuration (with “HiPath 4000 Expert
Access“) in exactly the same way as EXEC-USSU:UPDATAP,LTU
Number,UL;
22. Question: From the customer’s perspective, an IPDA access point is a

device that features both IP and TDM ports. The use of devices of this kind in
the customer network is prohibited for security reasons.
Answer: There is a widespread and logical ban on the operation of PCs that
have simultaneous network access to another networks (that cannot be
controlled and is not protected by a firewall, etc.) on the LAN. Devices of this
kind could be used as “private“ gateways in order, for example, to offer a
secure dial-in connection to the LAN.
An IPDA access point used as a gateway for voice connections from TDM <-
> IP must have access both to the LAN and to TDM ports.
The design of the HG 3575 guarantees a distinct separation between the
payload functionality and the signaling functionality.
In the payload part, random TDM <-> TDM or TDM <-> IP <-> TDM
connections are set up at the request of the HiPath 4000 central system. The
network consisting of the HiPath 4000 central system and the IPDA access
points provides a TDM operation that, from the outside, appears closed and
features an internal IP network for networking the access points.
If HG 3575 were misused, additional IP connections would be routed from the
NCUI, for example via PPP, to TDM connections.
This is not possible because
• the IP stack only responds to a limited number of ports (see Chapter

21, “IP Ports” in the document “Gateways HG 3500 and HG 3575”).
• the signaling unit can access the TDM payload

The HG 3575 supports PPP but only for a signaling connection over an
external modem connected using a serial V.24 interface in the case of
signaling survivability.
23. Question: We measured the mouth-to-ear delay in a voice connection

between the HiPath 4000 central system and an IPDA access point. The
delay clearly exhibits a very slow sawtooth pattern. In other words, it falls
steadily until it reaches a minimum threshold value and then jumps back to a
maximum value and then immediately starts to fall again. What causes this
sawtooth process and what can be done about it?
Answer: You have no digital trunk interfaces in the access point or do not use
these for clocking the HG 3575.
Without synchronization over digital trunk interfaces in the access point, the
clock generators in the HiPath 4000 central system and the access point
become asynchronous, despite the extremely high precision of the free-
running clock generator on the HG 3575 (ISO 11 573 class III, TIA stratum 4,
CTR4 and CTR12/13). Nevertheless, the unsynchronized clock generators
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
start to diverge over time. In the scenario you measured, the receiver works
with a slightly higher clock frequency than the sender. The IP connection
starts with the predefined jitter buffer value. As more data is read than sent,
the jitter buffer slowly runs idle. This explains the steadily falling mouth-to-ear
delay. When the minimum jitter buffer fill level is reached, time is “inserted“ at
the receive end during which the jitter buffer fills up again. This explains the
jump to the maximum value.
The converse effect can be observed in the opposite direction. The mouth-to-
ear delay climbs steadily until the upper limit of the jitter buffer is exceeded.
Time is then “removed“ and the jitter buffer is reset to the target value.
You can observe this effect in all devices that transfer data at a constant rate
over a long period of time without transfer clock synchronization. A solution
for the IPDA access points involves synchronizing the central system and all
HG 3575 ASCs with a common exchange clock.
24. Question: Why are calls from the IPDA to the central VoiceMail server routed
over the CO in the case of payload survivability? This doesn’t make any
sense. Can this be prevented?
Answer: VoiceMail systems are not affected by payload survivability. This is
explicitly specified as an exception in the sales release for HiPath 4000 (1st
supplement). In this case, calls are not routed over the survivability path (that
is the CO).
25. Question: Is NAT supported with IPDA?

Answer: NO.
26. Which resources are available per access point (NCUI2+/NCUI4/HiPath 4000
SoftGate)?
• 64 TSLs for conference
• 4 receivers for DTMF signaling (CR) - 32 receivers for HiPath 4000

Softgate
• 4 sender for DTMF signaling (CS) - 32 sender for HiPath 4000 Softgate
• 2 continuous-tone dial tone receivers (DTR-DT)
• 2 cadenced-tone dial tone receivers (DTR-TT)
• 2 test receivers (TESTR)
• 1 test sender (TESTS)
• up to 18 different tones
• 6 different announcements
• 1 music on hold
• 1 TDS port
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
A31003-H3160-S104-8-7620, 07/2014
08_faq_ipda.fm
A31003-H3160-S104-8-7620, 07/2014
01_ape_feature_desc.fm
Access Point Emergency Feature Description
Access Point Emergency (APE)
Access Point Emergency (APE)
1 Access Point Emergency Feature Description

The Access Point Emergency feature lets you maintain operation of Access
Points/HiPath 4000 SoftGates irrespective of whether or not the central system is
available.
Options for operating access points/HiPath 4000 SoftGates from additional,

physically separable control systems are provided for this purpose. These
additional control systems (survivability units) can be mounted in each AP 3700
IP access point.
In principle, you can control all access points/HiPath 4000 SoftGates associated
with a HiPath 4000 system from a single survivability unit (depending on the
survivability unit’s processor performance). Most of these scenarios avoid the use
of “classic“ shelves with a TDM connection and only use IPDA access points or
HiPath 4000 SoftGates.
In the case of the "Survivable HiPath 4000 SoftGate" feature, the survivability unit
is implemented as software on the HiPath 4000 SoftGates hosts. The survivability
unit takes over the operation of its own HiPath 4000 SoftGate if the central
controller fails (e.g. through loss of the IP connection to the central control unit).
As of HiPath 40000 V6 we have the following environment:
HiPath 4000 platform, which is the host for the follwoing virtual machines (VM):
• VM ADP, CCA, CCB, CCAP (RMX)
• VM Assistant
• VM CSTA
1.1 Access Point Emergency Implementation Scenarios
1.1.1 LAN Scenario

The central control unit - the communication server - is often housed in the main
computer center while the access points/HiPath 4000 SoftGates with the
survivability unit is located in the standby computer center. The access points/
HiPath 4000 SoftGates are distributed on the campus and networked over a high-
A31003-H3160-S104-8-7620, 07/2014
Access Point Emergency Implementation Scenarios
availability IP infrastructure. If the communication server in the main computer

center is not available, the survivability unit takes over the entire system
operation.
CSTA
main computer cebter
Assistant
high availability
LAN
HiPath 4000
ADP
CCA-SWU
CSTA
Survuvability Unit
Assistant
standby computer center
CC-AP
AP 3700 IP
Figure 1 LAN scenario
The survivability unit is indicated by the abbreviation CC-AP in all the following
figures and on all operational user interfaces. This is based on the logic used for
naming the control processors (CCA-SWU and ADP). Of course not only does the
CC-AP run on the survivability unit, rather also - as in the host system - HiPath
4000 Assistant and HiPath 4000 CSTA.
A31003-H3160-S104-8-7620, 07/2014
Access Point Emergency Implementation Scenarios
1.1.2 LAN/WAN Scenario

If the network features WAN routes that connect sites with several IPDA access
points/HiPath 4000 SoftGates, for example, we recommend installing an
individual survivability unit on each of these LAN islands. The access points/
HiPath 4000 SoftGates can then be operated autonomously not only in the event
of a central control unit failure but also if the WAN connection fails.
Communication
Server Access
Router Point
Access
CC-A Point
Access
HG 3575
LAN Point
AP 3x00
ADP Access
HG 3575
HiPath 4000
Point Per
AP 3x00
CSTA HG 3575
Per
AP 3x00
HG 3575 Per
Per
Assistant Per
Per
AP 3700 IP
Per
LAN Per
Access
Point CC-AP
HG 3575
AP 3700 IP
Per
Router
Per
CC-AP WAN
Access
Point
HGAccess
3575
AP 3x00
Access
Point
Access
Point Access
PerPoint
Access Point
HG 3575 Router Access
AP 3x00
Point
HG 3575 Point
AP 3x00
PerHG 3575 Access

Per HG 3575
AP 3x00
HG
Per3575 Point
AP 3x00
AP 3x00
Access
HG 3575
Per Per Point Per
AP 3x00
Per Per HG 3575

Per
AP 3x00
Per HG 3575 Per

Per Per
Per
Per
AP 3700 IP
Per
LAN Per
CC-AP
Figure 2 LAN/WAN scenario
A31003-H3160-S104-8-7620, 07/2014
Access Point Emergency and Signaling Survivability
1.1.3 Branch (WAN) Scenario

In the classic branch structure, numerous relatively small but broadly distributed
branches are connected via precisely dimensioned WAN routes to the company’s
host system. In this scenario, we recommend providing a survivability unit for the
IPDA access point/HiPath 4000 SoftGate in each individual branch. In this way,
you can ensure autonomous branch operation in the event of failure of the central
control unit or WAN connection.
Figure 3 Branch (WAN) scenario
1.2 Access Point Emergency and Signaling Survivability

The AP Emergency feature and the signaling survivability feature are not
alternatives. Instead, they complement each other. A reliable layer concept for
system stability can be implemented in all scenarios containing WAN routes.
1. Signaling survivability guarantees access point/HiPath 4000 SoftGate

operation over the central control unit in the event of a WAN malfunction. The
signaling survivability path is switched over without interruption.
2. AP Emergency takes over access point/HiPath 4000 SoftGate operation if the

central control unit fails.
Notes:
• The HSR signaling connection from the APE to the Access Point/HiPath 4000
SoftGate is always only a pure TCP/IP connection as opposed to a "HSR over
UDP" connection (regardless of the SIGMODE configuration in AMO UCSU).
• There is always only a single HSR signaling connection over a defined path
between the APE and Access Point/HiPath 4000 SoftGate and no alternative
survivability path.
Figure 4 “AP Emergency scenario” illustrates a mixed scenario that will be

referred to throughout the manual. In this figure, the broken blue lines represent
the communication paths between the central control unit and the access points/
HiPath 4000 SoftGates and the red dotted lines represent communication
between the survivability units and the access points/HiPath 4000 SoftGates
allocated to them.
A31003-H3160-S104-8-7620, 07/2014
Survivability Unit in AP 3700 IP
LTU LTU LTU

Access Access Access
Modem Rout Rout
HG HG HG
AP 3500
AP 3700 IP
AP 3700 IP
Mode Mode
Per Per Per
Per Per Per

EG 17
CC- CC-
EG 43
Router
Central LTU
System Access
WAN Rout
HG
AP 3700 IP
CC-A Mode Per
ADP Mode
PSTN Per
Router
LTU
CSTA
HiPath 4000
Access CC-
LTU HG
Access
AP 3700 IP
Assist Rout
Per
HG
AP 3300
HG 3500 Mode
Per Per
HG 3500 Per CC-
EG 35 EG 99
Per
Per
Figure 4 AP Emergency scenario
1.3 Survivability Unit in AP 3700 IP

The survivability unit can only be used in AP 3700 IP access points. However, it
can control all possible IPDA access point models (AP 3300 IP, AP 3500 IP, AP
3700 IP) and HiPath 4000 SoftGates. Access points are controlled regardless of
whether the access point features NCUI2+ or NCUI4.
The survivability unit consists of a cassette with cPCI backplane, DSCXL2

processor, power supply and redundant fan trays.
Depending on the power supply module, it can be powered with 110/230 V

alternating current or 48 V direct current. In AP 3700 IP, there is no electrical
connection between the access point and the survivability unit.
Communication between the survivability unit and the NCUI2+/4 on the same
access point/HiPath 4000 SoftGate only runs via the IP network.
1.4 Survivability unit on HiPath 4000 SoftGate

In the case of the "Survivable HiPath 4000 SoftGate" feature, the survivability unit
is implemented as software on the HiPath 4000 SoftGate host.
A31003-H3160-S104-8-7620, 07/2014
Allocating Access Points/HiPath 4000 SoftGates to a Survivability Unit
1.5 Allocating Access Points/HiPath 4000 SoftGates to a Survivability Unit

Access points/HiPath 4000 SoftGates are not directly allocated to a survivability
unit. Instead, they are allocated to an emergency group. The group defines which
access points/HiPath 4000 SoftGates are to be treated the same.
For example, it does not make sense to switch control of an individual access
point/HiPath 4000 SoftGate without trunk access from the host system to a
survivability unit. It makes more sense to switch an entire group in one go that
also contains an access point/HiPath 4000 SoftGate with trunk access.
Switchover regulations are defined per access point/HiPath 4000 SoftGate and
group.
By introducing the abstract emergency groups, you can control several groups
independently of a shared survivability unit.
The hierarchical assignment is simple:
• An access point/HiPath 4000 SoftGate can belong to exactly one

emergency group.
• An emergency group can be controlled by exactly one survivability unit.
All combinations with 1 to 83 access points/HiPath 4000 SoftGates in 1 to 83

emergency groups on 1 to 83 survivability units are possible. However, you must
calculate the necessary processor performance (the survivability unit
corresponds to a monoprocessor system) to ensure that the survivability unit is
not assigned any more access points/HiPath 4000 SoftGates than allowed by the
processor performance. Because of that a maximum of 40 access points/HiPath
4000 SoftGates for each mono processor system or survivability unit is allowed.
There are two kinds of access points/HiPath 4000 SoftGates, depending on the
type of connection; these are “Direct Link” (APDL) and “Networked Link” (APNW).
For details, see “IP Distributed Architecture”, Section 2.2, “Access Point”.
IMPORTANT: A survivability unit in an APNW access point/HiPath 4000

SoftGate cannot control any APDL access points/HiPath 4000 SoftGates.
However, a survivability unit in an APDL access point/HiPath 4000 SoftGate can
control both APDL and APNW access points/HiPath 4000 SoftGates.
1.6 Switchover in Emergency Mode

When a HG 3575/virtual HG 3575 discovers an interruption of the signaling
connection to the central control unit, it reports this event to the allocated
survivability unit.
A31003-H3160-S104-8-7620, 07/2014
Switchover in Emergency Mode
Emergency mode, that is, when access point/HiPath 4000 SoftGate is controlled
by a survivability unit, is the one escalation level higher than signaling
survivability. If signaling survivability is configured when the connection is lost,
signaling survivability first attempts to control the access points/HiPath 4000
SoftGates via modem. Emergency mode is initiated if this fails (for example,
because central control unit is not available).
The survivability unit uses preconfigured rules to decide whether it should take
over access point/HiPath 4000 SoftGate control or not.
• Each access point/HiPath 4000 SoftGate is assigned a weight.
• If the total weight of all access points/HiPath 4000 SoftGates in an

emergency group that has lost its connection to the central control unit is
greater than the limit specified, the survivability unit assumes control of all
access points/HiPath 4000 SoftGates assigned to this group
• However, access points/HiPath 4000 SoftGates can also be configured

so that they can always be individually controlled by the survivability unit
regardless of their weighting.
• In addition, you can switch control of
• individual access points/HiPath 4000 SoftGates
• all access points/HiPath 4000 SoftGates in an emergency group
• all access points/HiPath 4000 SoftGates in all emergency groups in a

survivability unit or
• all access points/HiPath 4000 SoftGates in the entire HiPath 4000

system
to the assigned survivability unit(s) at any time.
The survivability unit takes over control of the access point/HiPath 4000 SoftGate
by instructing the HG 3575/virtual HG 3575 to initiate a restart and then start up
with the survivability unit. The HG 3575/virtual HG 3575 restart triggers a restart
in all peripheral boards on the access point/HiPath 4000 SoftGate.
– All calls are cleared down.
– Features with active logon, e.g. mobile subscribers (PIN, mobile HFA),
are logged off.
– Features that can be configured by the user, such as key layout for (name
keys, DSS keys), forwarding key, reminder key, etc., are set up in the
state that they were in when the data was incorporated from the host
system (see also Section 1.8, “Configuration Data”).
A31003-H3160-S104-8-7620, 07/2014
Reverting to Normal Operation
1.7 Reverting to Normal Operation

When a HG 3575/virtual HG 3575 discovers that the signaling connection to the
central control unit has been restored, it reports this event to the allocated
survivability unit.
The survivability unit uses preconfigured rules to decide whether or not it should
hand back access point/HiPath 4000 SoftGate control to the host system.
• Every access point/HiPath 4000 SoftGate in an emergency group must

have a stable connection to the host system for a minimum set time
• Automatic reversion is only permitted during a set interval during the day.
The interval can be set to 24 hours so that automatic reversion is possible
at any time.
• Automatic reversion can be deactivated.
• You can also switch back control of
• individual access points/HiPath 4000 SoftGates,
• all access points/HiPath 4000 SoftGates in an emergency group,
• all access points/HiPath 4000 SoftGates in all emergency groups in a

survivability unit or
• all access points/HiPath 4000 SoftGates in the entire HiPath 4000

system
to the central control unit at any time.
The survivability unit returns access point/HiPath 4000 SoftGate control to the
central control unit by instructing the HG 3575/virtual HG 3575 to initiate a restart
and then start up with the central control unit. The HG 3575/virtual HG 3575
restart triggers a restart in all peripheral boards on the access point/HiPath 4000
SoftGate.
– All calls are cleared down.
– Features with active logon, e.g. mobile subscribers (PIN, mobile HFA),
are logged off.
– Features that can be configured by the user, such as key layout (name
keys, DSS keys), forwarding key, reminder key, etc., are set up in the
state which is active in the host system - i.e. generally as it was prior to
switchover.
A31003-H3160-S104-8-7620, 07/2014
Configuration Data
1.8 Configuration Data

The entire HiPath 4000 system including all its access points/HiPath 4000
SoftGates and survivability units is only configured in the host system.
Local administration of the feature is not possible at the survivability unit with the
exception of HiPath 4000 Assistant , Backup and Restore.
A special backup of the HiPath 4000 system database (HiPath 4000 Assistant >
Backup and Restore in the host system) is performed at set intervals (usually
once a day).
The survivability units perform continuous checks (every 10 minutes) to see if a

new HiPath 4000 database backup is available. If this unit is not actively
controlling an access point/HiPath 4000 SoftGate (emergency mode), it
downloads the saved data and incorporates it by means of a reload (HiPath 4000
Assistant > Backup and Restore on the survivability unit).
The backup data is stored on a file server. This file server may be located in the
customer’s computer center. You can also use the HiPath 4000 Manager platform
as a file server.
The daily backup is configured on the file server in such a way that it always
contains the complete system with database, patches and software.
However, transmission from the host system to the file server and from the file
server to the survivability unit is optimized. Only different data is actually
transferred.
For more information on the “Backup and Restore” application please refer to the
online help.
1.9 Transferring new System Releases and Patches

HiPath 4000 system complexity is considerably increased by survivability units.
To keep operation and maintenance costs low, system releases and patches are
automatically distributed to the survivability units.
In addition, new system releases and patches are incorporated in the backup/
restore process for the database (see Section 1.8, “Configuration Data”).
1.10 Connection Between Subsystems (Islands)

If a HiPath 4000 system breaks down in emergency mode into several
autonomous islands, how can the islands then communicate with each other? An
autonomous island is defined as a survivability unit and all the access points/
HiPath 4000 SoftGates over which the unit currently has active control.
A31003-H3160-S104-8-7620, 07/2014
Time Synchronization
Everything else remains the same within each individual island:
• Calls between subscribers in the same access point/HiPath 4000 SoftGate

are switched within the access point/HiPath 4000 SoftGate.
• Calls between subscribers in different access points/HiPath 4000 SoftGates

of an island are switched via IP connections between the access points/
HiPath 4000 SoftGates.
• Incoming/outgoing trunk calls are conducted via the island’s trunk interfaces.
• Incoming/outgoing calls in networked systems are conducted via the island’s

tie trunk interfaces.
What happens to calls for subscribers on another island?
All survivability units have the same complete host system database. Therefore,
every island knows every subscriber in the entire configuration, including all
subscribers on other islands. Access points/HiPath 4000 SoftGates outside the
island are configured but cannot be reached. All boards and their subscribers,
trunks and tie trunks are therefore known and belong to a set hierarchy (UNACH).
Although the IP infrastructure between some islands may still be intact, no inter-
island calls between access points/HiPath 4000 SoftGates are switched via IP.
Trunk interfaces can still be used for inter-island communication. It is therefore

still possible to reach a subscriber who is known but not directly available in
another island over CO. The “Alternate Routing on Error“ feature supports rule-
based call number modification in emergency mode.
This feature guarantees Basic Call connectivity for traffic between the islands.
For this feature to work, the trunks on the islands must use different access
codes. If all trunks use the same access code, directed routing must be
performed by the carrier using the complete number dialed (CENTREX).
If the islands are integrated in an extensive HiPath 4000 network with QSig
trunks, the LCR configuration must include normal and emergency mode
because the system has only one configuration. Even in this scenario, Basic Call
connectivity is guaranteed for incoming, system-wide traffic to an access point/
HiPath 4000 SoftGate which results in a transit connection. In order to support
network-wide features, the islands should be configured as virtual nodes.
Payload survivability does not work in emergency mode as the islands involved
no longer have a shared control unit.
1.11 Time Synchronization

A31003-H3160-S104-8-7620, 07/2014
Feature Licensing
1. The IP network has a time server, which supports time synchronization of all
HiPath 4000 processors (the central processor and all survivability units)
using the Network Time Protocol.
For more information on date/time settings and time synchronisation please refer
to “Section 2 - System Components (Hardware, Software)” of the service manual,
“Time Synchronization in the HiPath 4000 System”.
1.12 Feature Licensing

A license is necessary for operating a survivability unit in a HiPath 4000 system.
All host system licenses are also used on the survivability units in emergency
mode.
1.13 Application Support in Emergency Mode

External HiPath CAP
The HiPath CAP (Common Application Platform) supports the AP Emergency
feature so that a number of applications can function on both the host system and
the survivability unit.
The prerequisites for this are:
• the application and HiPath CAP have a functioning IP connection to the

survivability unit
• The application is based on HiPath CAP (CA4000 is not sufficient)
• the application only requires resources that are controlled by one and the
same survivability unit.
HiPath 4000 CSTA (CAP Inside)

The protocol between the external HiPath CAP and the HiPath 4000 PBX
changes with the HiPath 4000 CSTA (CAP Inside), i.e. from ACL to Standard
CSTA.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring the APE Feature (Access Point Emergency)
2 Configuring the APE Feature (Access Point Emergency)

To configure the AP Emergency feature, you must have a good understanding of
the functioning of this feature. This overview is found in Chapter 1, “Access Point
Emergency Feature Description”.
IMPORTANT: For emergency mode, configuration of the feature “Alternate

Routing on Error“ is mostly required so that subscribers of different “emergency
islands“ can contact one another.
This is described in the service manual „Section 3 - Feature Usage Examples >
Alternate Routing on Error“.
In some installations trunk and tie-line circuits have to be configured in order to
access a HiPath 4000 network or the public network from the “islands“.
Conclude this part of the configuration before configuring the AP Emergency
feature.
You can prevent APE from taking effect if a fault occurs in the network for
example. If, however, the above requirements have not been fulfilled, the commu-
nication capability of an “emergency island“ may be restricted and it may no
longer be possible to make emergency calls.
The feature configuration is divided into the following steps:
• Activities on HiPath 4000 host system
• Configuring or Modifying a CC-AP/Survivable HiPath 4000 SoftGate in

HiPath 4000
• Configuring or Modifying an Emergency Group
• Configuring Access Points/HiPath 4000 SoftGates for AP Emergency
• Configuring the Display for AP Emergency on the Terminal
• Defining the Switchover Delay
• Time Synchronization Between the Host System and CC-AP/Survivable

• Activities on the survivability unit - CC-AP/Survivable HiPath 4000 SoftGate
• Initial Startup of the CC-AP/Survivable HiPath 4000 SoftGate
• Verification and Acceptance of the AP Emergency Configuration
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring or Modifying a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000
2.1 Configuring or Modifying a CC-AP/Survivable HiPath 4000 SoftGate in

HiPath 4000
The CC-AP/Survivable HiPath 4000 SoftGate is always addressed with the LTU
number of the access point/HiPath 4000 SoftGate in which it is integrated.
Only the IP address for the IPDA LAN connection of the CC-AP/Survivable
HiPath 4000 SoftGate and the operating mode of the Ethernet interface are
required as configuration data. All other parameters necessary for IP
communication are taken from the CBM configuration of HG 3575 of the access
point/HiPath 4000 SoftGate.
Parameter “Network Link“ Access Point/ “Direct Link“ Access Point/

HiPath 4000 SoftGate HiPath 4000 SoftGate
IP address Directly configured
Netmask HG 3575 network mask HiPath 4000 LAN segment
APRT: TYPE=APNET - network mask
NETMASK SIPCO: TYPE=LSNET -
NETMASK
Default router Default router in the network of Default router in the network of
the the
access point/HiPath 4000 access point/HiPath 4000
SoftGate SoftGate
UCSU: UNIT=AP - APRTADDR UCSU: UNIT=AP - APRTADDR
that is usually the
default router of the HiPath 4000
LAN segment
SIPCO: TYPE=LSNET - DEFRT
VLAN tagging STMIB: MTYPE=NCUI2 - TYPE=IFDATA - VLAN
VLAN ID STMIB: MTYPE=NCUI2 - TYPE=IFDATA - VLANID
TOS byte for the STMIB: MTYPE=NCUI2 - TYPE=IFDATA - TOSLAN
signaling
connection
Table 1 Configuration parameters derived for the CC-AP/Survivable

A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring or Modifying a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000
partners (CC-AP/Survivable HiPath 4000 SoftGate or LAN switches or routers)!
“Autonegotiate“ setting of the other partner.
IMPORTANT: Incorrect settings cannot normally be detected by the system and

therefore go unreported. If one device is operating in full duplex and the other in
half duplex mode, this is not immediately noticeable. Where there is a high
payload, the device set to half duplex will report a higher number of late collisions
and the packet delay will increase sharply.
IMPORTANT: If the LAN port to which the CC-AP/Survivable HiPath 4000

SoftGate is connected does not support auto-negotiation, or if it does not function
reliably, the CC-AP/Survivable HiPath 4000 SoftGate Ethernet interface must be
set to fixed values.
In the example, the CC-AP/Survivable HiPath 4000 SoftGate is configured or

modified in access point/HiPath 4000 SoftGate 99.
The IP address is 192.168.23.199, the Ethernet interface is set to 10 Mbps, half

duplex.
Configuration Management --> System Data --> IPDA --> IPDA CC

Access Point
Click Search and select CC-AP/Survivable HiPath 4000 SoftGate or create
a New one.
Set the IP Address and the Ethernet interface transmission speed (Speed)
and mode and Save.
ADD-APESU:DATA=CCAP,CCAPNO=99,IPADDR=192.168.23.199;
or
CHANGE-
APESU:DATA=CCAP,CCAPNO=99,IPADDR=192.168.23.199;
The modified data does not take effect until after you have used HiPath 4000
Assistant Backup & Restore to copy the database to the CC-AP/Survivable
HiPath 4000 SoftGate, and the CC-AP/Survivable HiPath 4000 SoftGate has
accepted it.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Deleting a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000

Language
APESU CCAPNUM d LTU-Nummer des Access Points/HiPath 4000
SoftGates, in welchem der CC-AP/das Survivable
HiPath 4000 SoftGate eingebaut ist.
CCAPNO e Line/Trunk Unit Number of the access point/
HiPath 4000 SoftGate, where the CC-AP/
Survivable HiPath 4000 SoftGate is installed.
IPADR d IP Adresse des CC-AP/Survivable HiPath 4000
SoftGate.
IPADDR e IP Address of the CC-AP/Survivable HiPath 4000
SoftGate
Table 2 AMO APESU parameters in ADD or CHANGE branch under

DATA=CCAP
2.2 Deleting a CC-AP/Survivable HiPath 4000 SoftGate in HiPath 4000

When you delete a CC-AP/Survivable HiPath 4000 SoftGate, all emergency
groups allocated to it and the AP Emergency configuration of the allocated
access points/HiPath 4000 SoftGates are also automatically deleted. If you want
to keep the emergency groups, you must first allocate them to a different CC-AP/
Survivable HiPath 4000 SoftGate (CHANGE-
APESU:DATA=APEGRP,EGRPNO=xx,CCAPNO=yy;).

Access Point
Click Search and select the CC-AP/Survivable HiPath 4000 SoftGate, then
click Delete.
DELETE-APESU:CCAPNO=99;
accepted it.
2.3 Configuring or Modifying an Emergency Group

The emergency group is the logical connecting link between the access point/
HiPath 4000 SoftGate and CC-AP/Survivable HiPath 4000 SoftGate.
An access point/HiPath 4000 SoftGate is a member of exactly one emergency

group. An emergency group is served by exactly one CC-AP/Survivable HiPath
4000 SoftGate.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring or Modifying an Emergency Group
The emergency group was introduced for transferring complete groups of access
points/HiPath 4000 SoftGates, together and at the same time, to and from the
host system control to the CC-AP/Survivable HiPath 4000 SoftGate control.
While the primary function of the AP Emergency feature is handling the total
breakdown of the central control, the difficulty lies in appropriate handling of
partial breakdowns that may arise in the IP communication.
An emergency group typically combines access points/HiPath 4000 SoftGates

that together form a survivable unit. For example, this could be external location
connected via WAN.
Faults in the routing can result in only some of a group’s access points/HiPath
4000 SoftGates losing contact with the central control. In this case it would be
possible to transfer only the affected access points/HiPath 4000 SoftGates to the
CC-AP/Survivable HiPath 4000 SoftGate control. This interrupts communication
among the group’s access points/HiPath 4000 SoftGates, however. Calls would
then only be possible via the trunk. But does each access point/HiPath 4000
SoftGate have its own trunk line? Where are the central resources, such as
recorded announcements, servers, etc.?
This is why it often makes sense to switch a group only as a whole. In this way all
access point/sHiPath 4000 SoftGates remain under one control, and
communication among the access points/HiPath 4000 SoftGates runs via IP. All
access points/HiPath 4000 SoftGates can communicate with the rest of the
system via a common trunk line. In such cases, the access points/HiPath 4000
SoftGates of one emergency group will also belong to one source group for
source-dependent routing (see “IP Distributed Architecture”, Section 2.8, “Source
Dependent Routing”).
An emergency group is identified by a freely selectable number. Depending on

the installation, it may be advantageous to base the emergency group number on
the numbering of the associated source group or the CC-AP/Survivable HiPath
4000 SoftGate number.
Because plain text says more than any number, no matter how cleverly selected,
you can give each emergency group a name.
Each configured emergency group must be assigned to a CC-AP/Survivable

HiPath 4000 SoftGate. The assignment can be changed.
Weighting determines whether all of an emergency group’s access points/HiPath

4000 SoftGates switch to the CC-AP/Survivable HiPath 4000 SoftGate. A
weighting is assigned to each access point/HiPath 4000 SoftGate. The access
point/HiPath 4000 SoftGate contributes this weighting to the switching evaluation
in the event of a breakdown in its connection to the central control. A limiting value
can be defined for the group. When this value is exceeded, a switchover is carried
out.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Because they have higher weightings, access points/HiPath 4000 SoftGates with
trunk lines, central resources or VIP users are more likely to trigger a switchover
than access points/HiPath 4000 SoftGates with “standard features“.
When assigning the weightings, you must make sure that the weighting of all
access points/HiPath 4000 SoftGates that are assigned to an emergency group
is sufficient in order to reach the group’s limiting value. This is easy to overlook,
particularly when you are changing the configuration.
If the IP connections to central control are available again for all access points/
HiPath 4000 SoftGates, switchback to central control must be organized. There
will be customers who require immediate switchback to the central control, even
though this means disconnecting calls. Often, however, switchback is prohibited
at certain times. It may also be the case that only administrative switchovers are
permitted.
AP Emergency enables the activation of either automatic switchback, or of only

manual switchback. The parameters for automatic switchback are based on the
level of the emergency groups.
For the group - and therefore for all access points/HiPath 4000 SoftGates in the
group - you can stipulate how long the connection between each access point/
HiPath 4000 SoftGate and the central control must be stable without
interruptions, before a switchback will be considered.
Once the connection has been stable for the specified length of time, a check is
made as to whether a switchback is allowed at the time. Intervals during which a
switchback is permitted are set up for this purpose. The interval starts with the
specified hour (of the day) and ends at another specified hour. It is customary to
set up a time offset in order to shift the network load of scheduled activities away
from the exact hour. This allows you to specify how many minutes after the hour
the switchback interval is opened or closed. For example, if the switchback start
is at 8pm, the switchback end at 6am, and the offset is 13, this means that the
switchback can automatically take place during the time from 8:13pm and
6:13am. If there was a network fault in this configuration that interrupted the IP
connection between the central control and the access points/HiPath 4000
SoftGates from 9:05am until 9:15am, the automatic switchback would take place
at 8:13pm. If the fault occurs during the switchback interval, the switchback takes
place immediately once the IP connections between the central control and
access points/HiPath 4000 SoftGates have been stable again for the minimum
time.
A manual switchback is possible at any time. The administrator must ensure here
that the boundary conditions are correct (is switchback required? - are all access
points/HiPath 4000 SoftGates connected to the central control unit again?).
If a CC-AP/Survivable HiPath 4000 SoftGate fails while it is actively controlling

access points/HiPath 4000 SoftGates, the following behavior results:
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
• If the host system is available and if it has contact with an affected access
point/HiPath 4000 SoftGate, the host system takes control of the access
point/HiPath 4000 SoftGate again without taking the stability time and the set
switchover time into consideration.
• This only applies if automatic switchback has been configured.
• If manual switchback has been configured, an access point/HiPath 4000

SoftGate is not automatically taken over by the host system if the CC-AP/
Survivable HiPath 4000 SoftGate fails during emergency mode.
• If the host system is not available, control is no longer available for the access
point/HiPath 4000 SoftGate. It resets itself within the configured time period
and waits until a control makes contact with it.
Configuration Management --> System Data --> IPDA --> AP

Emergency Group
Click Search and select an emergency group or create a New one.
Set configuration parameters and Save.
ADD-
APESU:DATA=APEGRP,EGRPNO=2,CCAPNO=99,THRSHLD=100,SBMO
DE=,NAME=“BERLIN“,STABLE=10,SBBEGIN=20,SBEND=6,RSOFFS
ET=13;
or
CHANGE-
APESU:DATA=APEGRP,EGRPNO=2,CCAPNO=99,THRSHLD=100,SBMO
DE=AUTO,NAME=“BERLIN“,STABLE=10,SBBEGIN=20,SBEND=6,RS
OFFSET=13;
accepted it.

Language
APESU EGRPNUM d Identifikations-Nummer der Emergency Gruppe.
EGRPNO e Identification number of the Emergency Group.
Range [1 .. 99]
CCAPNUM d Nummer des CC-AP/Survivable HiPath 4000
SoftGate, dem die Emergency Gruppe zugeordnet
ist.
CCAPNO e Number of the CC-AP/Survivable HiPath 4000
SoftGate, to which the Emergency Group is
assigned.

DATA=APEGRP
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm

Language
SCHWELLE d Grenzwert für den Gewichtungsalgorithmus.
Bei Erreichen bzw. Überschreiten werden die
Access Points/HiPath 4000 SoftGates der
Emergency Gruppe in die Steuerung des CC-AP/
Survivable HiPath 4000 SoftGate umgeschaltet.
THRSHLD e Threshold for the weighing alogrithm.
When reached or exceeded, the access points/
HiPath 4000 SoftGates of the Emergency Group
are switched over into control of the CC-AP/
Survivable HiPath 4000 SoftGate.
Range [0 .. 1000]
RSMODE d Rückschaltemodus
Bestimmt, ob die Access Points/HiPath 4000
SoftGates der Emergency Gruppe automatisch,
oder ausschließlich manuell zur zentralen
Steuerung zurückgeschaltet werden dürfen.
Werte:
AUTO: Automatische Rückschaltung
MAN: Manuelle Rückschaltung
SBMODE e Switch-Back Mode
Specifies if the access points/HiPath 4000
SoftGates of the Emergency Group may be
switched back to the central control automatically
or only manually.
Values:
AUTO: Automatical Switch-Back
MAN: Manual Switch-Back
NAME d Name der Emergency Gruppe (maximal 22
Zeichen)
NAME e Name of the Emergency Group (maximum 22
characters)
STABIL d Stabilitätszeit
Minimale Zeitdauer, über welche alle Access
Points/HiPath 4000 SoftGates der Emergency
Gruppe eine stabile Verbindung zur zentralen
Steuerung haben müssen, bevor automatisch
rückgeschaltet werden darf.
Wertebereich [0 .. 255] Minuten
STABLE e Stability time
Minimum amount of time, during which all access
points/HiPath 4000 SoftGates of the Emergency
Group must have a stable connection to central
control, before they may be switched back.
Range [0 .. 255] Minutes
DATA=APEGRP
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Deleting an Emergency Group

Language
RSBEGIN d Beginn des täglichen Zeitintervalls für die
automatische Rückschaltung.
Die Rückschaltung ist erlaubt in der Zeit zwischen
RSBEGIN:RSOFFSET und RSENDE:RSOFFSET.
SBBEGIN e Begin of the daily time interval for the automatic
switch-back.
Switch-back is allowed during the time between
SBBEGIN:SBOFFEST and SBEND:SBOFFEST.
RSENDE d Ende des täglichen Zeitintervalls für die
automatische Rückschaltung.
Ist RSENDE gleich RSBEGIN gesetzt, darf
jederzeit automatisch rückgeschaltet werden.
SBEND e End of the daily time interval for the automatic
switch-back.
If SBEND is set identically to SBBEGIN, automatic
switch-back is allowed at any time.
RSOFFEST d Offsetwert [in Minuten] zum täglichen Zeitintervall
für die automatische Rückschaltung.
RSOFFSET e Offset value [in minutes] to the daily time interval
for the automatic switch-back.
DATA=APEGRP
2.4 Deleting an Emergency Group

When you delete an emergency group, the AP Emergency configuration of the
access points/HiPath 4000 SoftGates allocated to it are also automatically
deleted. If you want to keep the configuration of the access points/HiPath 4000
SoftGates, you must first allocate these to a different emergency group (CHANGE-
APESU:DATA=AP,APNO=xx,EGRPNO=yy;),
Configuration Management --> System Data --> IPDA --> AP

Emergency Group
Click Search select the CC-AP/Survivable HiPath 4000 SoftGate and
Delete.
DELETE-APESU:EGRPNO=99;
accepted it.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring Access Points/HiPath 4000 SoftGates for AP Emergency
2.5 Configuring Access Points/HiPath 4000 SoftGates for AP Emergency

To configure an access point/HiPath 4000 SoftGate for the AP Emergency
feature, it must be assigned to an already existing emergency group. Most of the
configuration specific to AP Emergency is performed at the level of the
emergency group.
Access points/HiPath 4000 SoftGates with the “direct link“ connection type
(APDL) - see “IP Distributed Architecture”, Section 2.2, “Access Point” - can only
be assigned to emergency groups for which the CC-AP/Survivable HiPath 4000
SoftGate is in an access point/HiPath 4000 SoftGate with link type APDL.
For access points/HiPath 4000 SoftGates with the “networked“ connection type
(APNW) there is no restriction for the connection type of the access point/HiPath
4000 SoftGate containing the CC-AP/Survivable HiPath 4000 SoftGate.
You must stipulate the emergency group to which an access point/HiPath 4000
SoftGate belongs as well as the “weight“ of the access point/HiPath 4000
SoftGate in question, i.e. its contribution to the weighting algorithm for the
switchover.
Regardless of the weighting in the emergency group, you can also specify that an
access point/HiPath 4000 SoftGate be immediately included in the control of the
CC-AP/Survivable HiPath 4000 SoftGate allocated to the emergency group when
the connection to the central control is lost. This exception to the group behavior
can for example be useful when an access point/HiPath 4000 SoftGate with VIP
users is equipped in such a way that it has its own trunk access and is therefore
independent of the availability of the other group members.
IMPORTANT: Access points/HiPath 4000 SoftGates that are switched over to

the CC-AP/Survivable HiPath 4000 SoftGate independently of the group and that
do not have their own trunk or tie line only allow access point/HiPath 4000
SoftGate internal communication. 
This prevents emergency calls from being forwarded over the trunk, for
example.
This exception only applies when the limiting value for the weighting within the
emergency group has not been reached. The weighting contribution of an access
point/HiPath 4000 SoftGate with separate switching is always taken into
consideration for the weighting of the group behavior. The access point/HiPath
4000 SoftGate is always included in the switchover when required by the
weighting for the emergency group. The switchback also takes place along with
the group.
Point
Click Search and select the access point/HiPath 4000 SoftGate.
Set the configuration parameters in the AP Emergency tab and Save.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring Access Points/HiPath 4000 SoftGates for AP Emergency
ADD-
APESU:DATA=AP,APNO=99,EGRPNO=2,WEIGHT=70,SWMODE=GROUG
;
or
CHA-
APESU:DATA=AP,APNO=99,EGRPNO=2,WEIGHT=70,SWMODE=GROUP
;
accepted it.

Language
APESU APNUM d LTU-Nummer des Access Points/HiPath 4000
SoftGates
APNO e Line/Trunk Unit Number of the access point/HiPath
4000 SoftGate
EGRPNUM d Identifikations-Nummer der Emergency Gruppe.
EGRPNO e Identification number of the Emergency Group.
GEWICHT d Gewichtsbeitrag des Access Points/HiPath 4000
SoftGates für den Gewichtungsalgorithmus.
Verliert der Access Point/HiPath 4000 SoftGate die
Verbindung zur zentralen Steuerung, so wird sein
Gewichtsbeitrag in die Gewichtung der Emergency
Gruppe eingebracht.
WEIGHT e Weight share of the access point/HiPath 4000
SoftGate to the weighing alogrithm.
When the access point/HiPath 4000 SoftGate loses
the connection with the central control, it’s weight
share is brought into the weighing of the
Emergency Group.
Range [0 .. 1000]
UMSCHALT d Umschaltemodus
Bestimmt, ob ein Access Point/HiPath 4000
SoftGate ausschließlich zusammen mit der
gesamten Emergency Gruppe umgeschaltet wird,
oder ob er auch unabhängig von der Gewichtung
sofort vom CC-AP/Survivable HiPath 4000
SoftGate übernommen wird, wenn er die
Verbindung zur zentralen Steuerung verloren hat.
Werte:
GRUPPE: Umschaltung nur mit gesamter Gruppe
EINZEL: Einzelbehandlung bei der Umschaltung
Table 4 AMO APESU parameters in ADD or CHNAGE branch under

DATA=AP
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Examples for Determination of Weights

Language
SWMODE e Switch-Over Mode
Specifies if the access point/HiPath 4000 SoftGate
may be switched over only together with the
complete Emergency Group, or if it may be taken
over by the CC-AP/Survivable HiPath 4000
SoftGate independently to the weighing, as soon as
it loses connection with central control.
Values:
GROUP: Switch-Over only together with Group
SINGLE: Individual handling at Switch-Over
Table 4 AMO APESU parameters in ADD or CHNAGE branch under
DATA=AP
2.6 Examples for Determination of Weights

The combined use of access point/HiPath 4000 SoftGate weighting, threshold
settings for group switchover and, if necessary, exemption from the group rule
through individual switchover, form a powerful instrument for configuring
automatic switchover to the emergency mode. The following two examples
should help you to understand the calculations.
• Basic IP system (with no shelves in slots 1-15) with the communication server
located at the computer center and 30 access points/HiPath 4000 SoftGates,
1 CC-AP/Survivable HiPath 4000 SoftGate at the backup computer center,
and multiple trunk connections with the same code distributed on four access
points/HiPath 4000 SoftGates.
Sample configuration 1
(Emergency mode in the case of complete failure of the communication
server only, i.e. the connection from all access points/HiPath 4000 SoftGates
to the server has been lost)
– 1 emergency group, threshold = 300
– Weight of each of the 30 access points/HiPath 4000 SoftGates = 10

Disadvantage: If only one access point/HiPath 4000 SoftGate is not
available, for example as a result of a power failure, it is excluded from the
calculation since it does not have any contact with the CC-AP/Survivable
HiPath 4000 SoftGate. In such a scenario, the threshold cannot be reached.
Sample configuration 2
(If the connection between the communication server and more than half of
the access points/HiPath 4000 SoftGates is lost, the system switches to
emergency mode. This also applies if the same occurs with more than half of
the trunk connections).
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Examples for Determination of Weights
– Access points/HiPath 4000 SoftGates without a trunk connection: Weight

= 10
– Access points/HiPath 4000 SoftGates with a trunk connection: Weight =

75
• Conventional system at main location, branch 1 with 3 access points/HiPath

4000 SoftGates one of which has a trunk connection; branch 2 with 6 access
points/HiPath 4000 SoftGates, two of which have a trunk connection; branch
3 with 1 access point/HiPath 4000 SoftGate, which also has a trunk
connection; branch 4 has 4 access points/HiPath 4000 SoftGates, one of
which has a general trunk connection and another which contains the ports
for the executive management with a separate trunk connection. Connectivity
via a local trunk connection is very important for the branches. If a single
access point/HiPath 4000 SoftGate without a trunk connection “fails“, this
should not lead to a change of group. If, however, two or more access points/
HiPath 4000 SoftGates fail, the group must be changed. Each location has an
individual access point/HiPath 4000 SoftGate equipped with CC-AP/
Survivable HiPath 4000 SoftGate.
Sample configuration 
Branch 1 (3 access points/HiPath 4000 SoftGates)

= 100
– Access point/HiPath 4000 SoftGate with a trunk connection: Weight = 200

Branch 2 (6 access points/HiPath 4000 SoftGates)

= 100
– Access points/HiPath 4000 SoftGates with a trunk connection: Weight =

100
Branch 3
– Access points/HiPath 4000 SoftGates: Weight = 100

Branch 4

= 100
– access point/HiPath 4000 SoftGate with a trunk connection: Weight = 200
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Removing Access Points/HiPath 4000 SoftGates from the AP Emergency Configuration
– Executive access point/HiPath 4000 SoftGate: Weight = 100, individual

switchover active
The CC-AP/Survivable HiPath 4000 SoftGate should be integrated in this
access point/HiPath 4000 SoftGate.
2.7 Removing Access Points/HiPath 4000 SoftGates from the AP

Emergency Configuration
You can remove an access point/HiPath 4000 SoftGate from the AP Emergency
configuration at any time.
IMPORTANT: When you delete an access point/HiPath 4000 SoftGate from the
AP Emergency configuration, its possible weighting contribution to the weighting
algorithm of the emergency group to which it belonged is also deleted.
Verify whether the emergency group’s limiting value “THRSHLD“ is still a valid
number.
Point
Click Search and select the access point/HiPath 4000 SoftGate.
Delete the Emergency Group Number on the AP Emergency tab and
Save.
DELETE-APESU:APNO=99;
accepted it.
2.8 Deleting the entire AP Emergency Configuration

If the entire AP Emergency configuration of a HiPath 4000 system is to be
deleted, this can be performed easily at system level. All CC-APs, all emergency
groups and the AP Emergency configuration of all access points/HiPath 4000
SoftGates are completely removed.

Access Point
Click Search and select the Object list view.
Select all (CC-AP/Survivable HiPath 4000 SoftGate) objects and Delete.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Configuring the Display for AP Emergency on the Terminal
DELETE-APESU;
accepted it.
2.9 Configuring the Display for AP Emergency on the Terminal

If an access point/HiPath 4000 SoftGate is actively controlled by a survivability
unit, i.e. a CC-AP/Survivable HiPath 4000 SoftGate, there are changes that the
user needs to know about.
This information is output on the second line of the terminals’ idle display. The
text to be output must be agreed upon with the customer.
The output text replaces the LOGO information that can be output during normal
operation.
The maximum text length is 22 characters and may comprise numbers and letters
in upper and lower case.
IMPORTANT: Insert blank spaces for all positions in the second display line
where information is output in idle mode, and leave enough room to allow the
information to be read.
For example, if the telephone’s number is shown in the first 5 spaces of the idle
display, you must start the AP Emergency information text with at least 6 blank
spaces.
Use the AMO ZANDE for this setting.
You must be in expert mode to make this setting with the AMO ZANDE.
(see AMO command)
CHANGE-ZANDE:TYPE=ALLDATA,APEDTXT=“ Emergency
operation “;
The text should be exactly 22 characters long.
accepted it.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Defining the Switchover Delay
2.10 Defining the Switchover Delay

If a breakdown has been detected in the HiPath 4000 host system or the IP
network, and if a CC-IP has decided based on its configured rules that access
points/HiPath 4000 SoftGates should be switched over, there is another point to
be considered:
How should the overall system react if the HiPath 4000 host system carries out a
RELOAD?
There are two possibilities:
1. React as quickly as possible, i.e. perform immediate switchover. 

In the case of a RELOAD, switchover to emergency operation is then always
performed.
2. Delay the switchover long enough to prevent a RELOAD leading to

emergency operation.
In line with this decision, you must set the AP Emergency switchover delay either
– to zero (switch immediately) or
– to the length of time that the HiPath 4000 system needs to execute a
complete RELOAD.
Data
Click Search, enter the switchover delay for AP Emergency in the System
data and Timing tabs and then click Save.
CHANGE-SIPCO:TYPE=TIMING,APESWDLY=5;
Sets the switchover delay to 5 minutes
->i.e. the system RELOAD takes 5 minutes; wait for the corresponding
length of time.
accepted it.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Querying the Connection Data

Language
SIPCO APESWDLY d APE Umschalteverzögerung
Das Umschalten eines Access Points/HiPath 4000
SoftGates in den Emergency Mode kann um eine
konfigurierbare Zeit verzögert werden.
Der Wert wird in Minuten angegeben.
Wertebereich [0 .. 99].
"0" sollte nicht konfiguriert werden, weil damit
würde der APE auch im Falle eines RMX Restarts
des Hostsystems (CCA/CCB) übernehmen.
Konfigurationsempfehlung und AMO Defaultwert:
5 (Minuten)
APESWDLY e APE Switch Over Delay
The switch-over of an Access Point/HiPath 4000
SoftGate to Emergency Mode can be delayed for a
configurable amount of time.
The value is entered in minutes.
Range [0 .. 99].
"0" should not be configured because then a switch
over to the APE is performed even in case of a
restart of the RMX of the host system (CCA/CCB).
Recommendation configuration and AMO default:
5 (minutes)
Table 5 The AP Emergency-specific parameter APESWDLY of the AMO

SIPCO in CHANGE branch under TYPE=TIMING
2.11 Querying the Connection Data
2.11.1 Querying the Connection Data via

Configuration Management
Configuration Management --> System Data --> Maintenance

--> IPDA - CC Access Point Maintenance
Click SEARCH and select CC-AP/Survivable HiPath 4000 SoftGate.
The table that this generates shows the connection status for all access
points/HiPath 4000 SoftGates that belong to the emergency groups of the
selected CC-AP/Survivable HiPath 4000 SoftGate.
2.11.2 Querying the Connection Data via AMO
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
A query for the AP Emergency configuration also includes output of the current
connection status. The amount of data output and the information it contains
depend on the logical level at which the query is running - and whether it is
performed in the HiPath 4000 host system or on a CC-AP/Survivable HiPath 4000
SoftGate.
DISPLAY-APESU;
• on HiPath 4000 host system
• all CC-APs
• all emergency groups
• all access points/HiPath 4000 SoftGates
• locally on a CC-AP/Survivable HiPath 4000 SoftGate
• local CC-AP/Survivable HiPath 4000 SoftGate
• all of the CC-AP/Survivable HiPath 4000 SoftGate Emergency groups
• all access points/HiPath 4000 SoftGates of the CC-AP/Survivable

HiPath 4000 SoftGate Emergency groups
DISPLAY-APESU:CCAPNO=xx; or DISPLAY-APESU:xx;
• on HiPath 4000 host system
• selected CC-AP/Survivable HiPath 4000 SoftGate
• all of the selected CC-AP/Survivable HiPath 4000 SoftGate

Emergency groups
• all access points/HiPath 4000 SoftGates of the selected CC-AP/

Survivable HiPath 4000 SoftGate Emergency groups

if the local CC-AP/Survivable HiPath 4000 SoftGate is selected
• local CC-AP/Survivable HiPath 4000 SoftGate
• all of the CC-AP/Survivable HiPath 4000 SoftGate Emergency groups
• all access points/HiPath 4000 SoftGates of the CC-AP/Survivable

HiPath 4000 SoftGate Emergency groups
if the local CC-AP/Survivable HiPath 4000 SoftGate is not selected:
system message
DISPLAY-APESU:EGRPNO=xx; or DISPLAY-APESU:,xx;
• HiPath 4000 host system
• selected emergency group
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
• all access points/HiPath 4000 SoftGates in the selected emergency

group

if an emergency group in the local CC-AP/Survivable HiPath 4000
SoftGate is selected
• selected emergency group
• all access points/HiPath 4000 SoftGates in the selected emergency

group
otherwise: system message
DISPLAY-APESU:APNO=xx; or DISPLAY-APESU:,,xx;
• HiPath 4000 host system
• selected access point/HiPath 4000 SoftGate

if an access point/HiPath 4000 SoftGate of an emergency group in the
local CC-AP/Survivable HiPath 4000 SoftGate is selected
• selected access point/HiPath 4000 SoftGate

otherwise: system message
CC-AP/Survivable HiPath 4000 SoftGate-specific block:

+------------------------------------------------------------------------------+
| CC-AP: 99 IP ADDRESS: 192.168.23 .199 |
| SPEED/WORK MODE(IPDA): 100MBFD |
+------------------------------------------------------------------------------+
Emergency group-specific block:

+------------------------------------------------------------------------------+
| AP EMERGENCY GROUP: 2 CC-AP: 99 NAME: BERLIN |
| THRSHLD: 100 SBMODE: AUTO |
| STABLE: 10 MIN SBBEGIN: 20 H SBEND: 6 H SBOFFSET: 13 MIN |
+------------------------------------------------------------------------------+
Access Point/HiPath 4000 SoftGate-specific block:

+------------------------------------------------------------------------------+
| AP: 99 AP EMERGENCY GROUP: 2 CC-AP: 99 WEIGHT: 70 SWMODE: GROUP |
| CONTROL UNIT: HOST-CC SIGNAL PATH: LAN |
| LAST RECORDED CONNECTION STATUS CHANGE: |
| |
| HOST-CC: CONNECTED: yes CONNECTED SINCE: 08-06-2004 18:20 |
| CC-AP: CONNECTED: yes CONNECTED SINCE: 18-06-2004 23:01 |
+------------------------------------------------------------------------------+
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Administration Switchover of Access Points/HiPath 4000 SoftGates
2.12 Administration Switchover of Access Points/HiPath 4000 SoftGates
2.12.1 Administration Switchover of Access Points/

HiPath 4000 SoftGates via Configuration Management
Configuration Management --> System Data --> Maintenance --> IPDA

- CC Access Point Maintenance
Click Search and select CC-AP/Survivable HiPath 4000 SoftGate.
In the main menu, select -> Action -> Execute.
In the mask that this generates, you can set
• whether the switchover should be to normal or emergency

mode,
• whether a particular access point/HiPath 4000 SoftGate, all

access points/HiPath 4000 SoftGates of a particular emergency
group, all access points/HiPath 4000 SoftGates of all
emergency groups in the selected CC-AP/Survivable HiPath
4000 SoftGate, or the entire system should be switched over.
2.12.2 Administrator Switchover of Access Points/

HiPath 4000 SoftGates via AMO
Administrative switchover of access points/HiPath 4000 SoftGates to

and from the central control to CC-AP/Survivable HiPath 4000 SoftGate
is possible at any time.
The task is forwarded to the HiPath 4000 host system via AMO. From there, it is
sent to the affected CC-AP/Survivable HiPath 4000 SoftGate via an affected
access point/HiPath 4000 SoftGate. Finally, the CC-AP/Survivable HiPath 4000
SoftGate instructs the HG 3575 of the affected access points/HiPath 4000
SoftGates to start up with the requested control (central control (host) or CC-AP/
Survivable HiPath 4000 SoftGate). If more than one CC-AP/Survivable HiPath
4000 SoftGate is affected, this process is repeated for each CC-AP/Survivable
Communication from the HiPath 4000 host system to the CC-AP/Survivable

HiPath 4000 SoftGate via access points/HiPath 4000 SoftGates requires that at
least one access point/HiPath 4000 SoftGate has a connection to both the central
control and the CC-AP/Survivable HiPath 4000 SoftGate. If this is not the case,
switchover cannot be initiated.
The switchover can take place at various levels:
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
• all access points/HiPath 4000 SoftGates of all emergency groups of all CC-
APs in the system
EXEC-APESU:SYSMODE=EMERG,LEVEL=SYSTEM; 
switches to the CC-AP/Survivable HiPath 4000 SoftGate
EXEC-APESU:SYSMODE=NORMAL,LEVEL=SYSTEM; 
switches to the central control
• all access points/HiPath 4000 SoftGates of all emergency groups of one CC-
AP/Survivable HiPath 4000 SoftGate
EXEC-APESU:SYSMODE=EMERG,LEVEL=CCAP,NO=99; 
EXEC-APESU:SYSMODE=NORMAL,LEVEL=CCAP,NO=99; 
• all access points/HiPath 4000 SoftGates of one emergency group (of one CC-
AP/Survivable HiPath 4000 SoftGate)
EXEC-APESU:SYSMODE=EMERG,LEVEL=APEGRP,NO=2; 
EXEC-APESU:SYSMODE=NORMAL,LEVEL=APEGRP,NO=2; 
• one access point/HiPath 4000 SoftGate (of one emergency group (of one CC-
AP/Survivable HiPath 4000 SoftGate))
EXEC-APESU:SYSMODE=EMERG,LEVEL=AP,NO=99; 
switches to CC-AP/Survivable HiPath 4000 SoftGate
EXEC-APESU:SYSMODE=NORMAL,LEVEL=AP,NO=99; 
IMPORTANT: The switchover is always performed for all selected access points/
HiPath 4000 SoftGates that have contact with the requested control, regardless
of group rules.
If some access points/HiPath 4000 SoftGates in a selection (SYSTEM, CC-AP/
Survivable HiPath 4000 SoftGate, APEGRP) do not have contact with the
requested control, these are not switched over. 
The AMO then issues the message “partially performed“.
Following a partial switchover, resources important for operation (such as trunk
lines) may not be available for a group!
For this reason, the connection status must be queried and verified before a
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
manual switchover. See Section 2.11, “Querying the Connection Data”.
IMPORTANT: Access points/HiPath 4000 SoftGates that are switched over

independently of the group and that do not have their own trunk or tie line only
allow access point/HiPath 4000 SoftGate internal communication. 
This prevents emergency calls from being forwarded over the trunk, for
example.

Language
APESU SYSMODE d Gibt an, welche Steuerung übernehmen soll.
Werte:
NORMAL: zentrale Steuerung (Host)
EMERG: Emergency Steuerung (CC-AP/
Survivable HiPath 4000 SoftGate)
SYSMODE e Identifies, which control shall take over.
Values:
NORMAL: Central Control (Host)
EMERG: Emergency Control (CC-AP/Survivable
HiPath 4000 SoftGate)
LEVEL d Gibt an, auf welcher System-Ebene umgeschaltet
werden soll.
Werte:
SYSTEM: gesamtes System (alle Access Points/
HiPath 4000 SoftGates, APEGRPs, CC-APs)
CCAP: ein CC-AP/Survivable HiPath 4000
SoftGate (alle Access Points/HiPath 4000
SoftGates, APEGRPs)
APEGRP: eine Emergency Gruppe (alle Access
Points/HiPath 4000 SoftGates)
AP: ein Access Point/HiPath 4000 SoftGate
LEVEL e Identifies on which system level the switch over
shall be executed.
Values:
SYSTEM: complete system (all access points/
HiPath 4000 SoftGates, APEGRPs, CC-APs)
CCAP: one CC-AP/Survivable HiPath 4000
SoftGate (all access points/HiPath 4000
SoftGates, APEGRPs)
APEGRP: one Emergency Group (all access
points/HiPath 4000 SoftGates)
AP: one Access Point/HiPath 4000 SoftGate
NUMMER d Gibt die Nummer des betroffenen CC-AP/
Survivable HiPath 4000 SoftGate, der Emergency
Gruppe oder des Access Points/HiPath 4000
SoftGates an.
Table 6 AMO APESU parameter in the EXEC branch
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Time Synchronization Between the Host System and CC-AP/Survivable HiPath 4000 SoftGate

Language
NO e Identifies the number of the affected CC-AP/
Survivable HiPath 4000 SoftGate, Emergency
Group or Access Point/HiPath 4000 SoftGate
Table 6 AMO APESU parameter in the EXEC branch
2.13 Time Synchronization Between the Host System and CC-AP/

1. A time server is available in the IP network, which supports time

synchronization of all HiPath 4000 processors (the central processor and all
survivability units) using the Network Time Protocol.
For more information on date/time settings and time synchronisation please refer
to
• Section 1.11, “Time Synchronization” or in
• “Section 2 - System Components (Hardware, Software)” of the service

manual, “Time Synchronization in the HiPath 4000 System”.
2.14 Initial Startup of the CC-AP/Survivable HiPath 4000 SoftGate
2.14.1 Preparation
During the initial installation, you must make sure that the same APS version that
is currently running on the host system is also running on the CC-AP/Survivabel
HiPath 4000 SoftGate hard disk.
DISPLAY-APS;
This display on the HiPath 4000 host system outputs the part numbers of
the loaded program system. Of interest here is the part number of the Y0-
APS.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
Verification and Acceptance of the AP Emergency Configuration
PROGRAM SYSTEM : Y0-EN0YC

VERSION NUMBER :10
CORRECTION VERSION NUMBER : 001
PART NUMBER : P30252xxxxxxxxxxx
PROGRAM SYSTEM WITH CODE SUBSYSTEMS
INTERFACE VERSION:
PROGRAM SYSTEM CONTAINS NO INTERFACE VERSION
2.14.2 CC-AP
Please refer to the apropriate How To in the Release Note for HiPath 4000 V6.
2.14.3 Survivable HiPath 4000 SoftGate

Please refer to the apropriate How To in the Release Note for HiPath 4000 V6.
2.15 Verification and Acceptance of the AP Emergency Configuration

The customer uses the AP Emergency feature to facilitate telephone calls during
emergency situations where the central control and/or essential components of
the IP infrastructure are not available.
As a rule, this emergency situation occurs only very rarely. For this reason it is
particularly crucial that the emergency measures function as intended, should
they actually be needed at some point.
It is essential that the function of the AP Emergency configuration be verified by

an acceptance test after the initial startup and after substantial modifications.
To this end, each emergency group must be switched over once to the CC-AP/
Survivable HiPath 4000 SoftGate for administration. In emergency operation, it
must then be verified that emergency calls, communication to the trunk and other
systems in the network, and communication between emergency groups at
different CC-APs function as planned. Where applicable, also include installed
applications that support emergency operation in the test.
Also verify the communications capability of access points/HiPath 4000

SoftGates that can be switched to the CC-AP/Survivable HiPath 4000 SoftGate
independently of the emergency group when the group is running in normal
operation.
You can conduct the tests when the system load is low.
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
A31003-H3160-S104-8-7620, 07/2014
02_ape.fm
A31003-H3160-S104-8-7620, 07/2014
03_backup_restore.fm
Backup & Restore
HiPath 4000 Assistant Backup & Restore on HiPath 4000 Host System
3 Backup & Restore
3.1 HiPath 4000 Assistant Backup & Restore on HiPath 4000 Host System
To support the backup and restore processes for the AP Emergency feature, the
HiPath 4000 Assistant Backup & Restore application replicates the software and
the configuration data from the host system to the CC-APs/Survivable HiPath
4000 SoftGates.
As of HiPath 4000 V6 we have to differentiate between HOST and APE:
• HOST
HiPath 4000 Platform with the virtual machines ADP/CCA, HiPath 4000
Assistant and HiPath 4000 CSTA.
• APE
HiPath 4000 Platform with the virtual machines CCAP, HiPath 4000 Assistant
and HiPath 4000 CSTA.
Therfore, there are four possible systems that have to be synchronized. But at the
moment only CC-AP on APE is synchronized with ADP/CCA on host. This is
provided by HiPath 4000 Assistant Backup & Restore.
For more information please refer to the online help of Backup & Restore.
Basic conditions regarding timing

A backup can only be carried out when the AP backup server is free, i.e. not
currently blocked by restore processes. You can set the number of simultaneous
restore processes allowed, in order to limit the load on the server or network.
The interval between two scheduled backups must therefore be sufficient to allow
the backup and restore processes of all CC-APs in the system to be carried out.
If the number of CC-APs is larger than the number of restore operations

supported simultaneously, some CC-APs must wait until the capacity on the AP
backup server is free before performing restore procedures. This leads to an
increase in the required restore time that must be considered in the process as a
whole.
The time required is determined by the data volume to be transported and the
available transmission bandwidth. The maximum data volume (in the case of a
system maintenance release) is estimated at 100 MB. The average size will be
less than 10% of the maximum.
If the restore process on the CC-AP/Survivable HiPath 4000 SoftGate requires a

great deal of time (available transmission bandwidth is limited), you must ensure
that all CC-APs can be restored at the same time.
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
The start time for the backup also determines indirectly the content of the
database.
For example, if the customer usually activates fixed call forwarding on the
telephone and if the backup is performed outside business hours, the saved
database will contain the activated call forwarding settings.
But if a problem arises during the day, which initiates emergency mode, it will be
initiated with the saved call forwarding settings.
3.1.1 Configuring an AP Backup Server with HiPath

4000 Assistant Backup & Restore
In the first configuration step, you define where the HiPath 4000 backup data
should be stored. To do this, you must specify the computer that should act as the
file server (AP backup server), the directory where the data should be stored, and
the login data for access. Configuration on the file server (create the directory,
define the user ID) should be completed before the configuration as part of HiPath
4000 Assistant Backup & Restore.
• Use the Web browser to display the HiPath 4000 Assistant start page and log
in with the user ID “rsta“.
• In the left menu bar, select the function area Software Management.
• Select the application Backup & Restore provided as a submenu option

under Software Management.
• In the Backup & Restore user interface, select the function AP Backup
Server under Administration.
Figure 5 HiPath 4000 Assistant Backup & Restore: configuring an AP

backup server
The following fields must be now be completed:
• Select the Protocol (SFTP or NFS) - typically: SFTP

If you want to configure the AP backup server on the HiPath 4000 host
system, you must select SFTP as the protocol.
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
• Maximum number of concurrent CC-AP/Survivable HiPath 4000

SoftGate transfers
In the maximum configuration, 83 CC-APs may want to sign on to the AP
backup server and download the latest backup set simultaneously. If the
server does not support this large number of simultaneously logged-in
systems, or if you want to reduce possible load peaks on the server, you
can adjust the maximum number of simultaneously logged-in CC-APs
accordingly. Dependencies are shown in “Section 3.1, “Basic conditions
regarding timing”“.
• Enter the IP Address or Host Name of the AP backup server

You can only enter a host name if either it is configured directly in UBA or
if the name resolution is configured with DNS.
• Enter the Directory on the AP backup server that should be used for the
backup and restore
If you want to configure the AP backup server on the HiPath 4000 host
system, you must select the directory already provided for this purpose
(“/.AS/BACKUP/IPDA“ ).
The directory must be able to hold approximately 100 MB of data.
• If you selected SFTP as the protocol, you still need to configure the Login
name and the Password for accessing the AP backup server (SFTP
server). If the SFTP server requires an Account, this also needs to be
entered.
If you want to run the AP backup server on the HiPath 4000 host system,
for security reasons you should configure the login under apeftp. You do
not need to configure an account in this case.
IMPORTANT: Remember that the login password for the AP backup server
must be maintained, both on the backup server and in the HiPath 4000
Assistant Backup & Restore configuration of the HiPath 4000 host system
and the CC-APs.
Complete the AP backup server configuration with
• Testing - Save the configuration and test the access to the AP backup server.
You should always use this option if the file server is already available when
it is configured in the network.
• Configure - Save the configuration without an access test.

You should only use this option if the file server is not available when it is
configured in the network.
In this way, memory is configured for the backup.
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
3.1.2 Creating a Schedule for the Backup

In the second configuration step, you must now define when HiPath 4000
Assistant Backup & Restore should carry out a backup on the configured AP
backup server. Typically, a backup is performed daily at a time when there is not
much activity.
When you select a start time for the backup, keep in mind that this also indirectly
defines the start time for the restore on the CC-APs. The restore on the CC-AP/
Survivable HiPath 4000 SoftGate starts as soon as the CC-AP/Survivable HiPath
4000 SoftGate detects availability of new completed backup. Dependencies are
shown in the section “Section 3.1, “Basic conditions regarding timing”“.
Prerequisite:
• Logged on to the HiPath 4000 Assistant via a Web browser under the ID
“rsta“.
• Software Management -> Backup & Restore has been started.
• In the HiPath 4000 Assistant Backup & Restore user interface, select the
function Schedule.
Figure 6 HiPath 4000 Assistant Backup & Restore: Creating a schedule

for the backup
The following fields must be now be completed:
Field name Value Explanation

Type AP Emergency Only this value is permitted
Unit All Only this value is permitted
Status Activated This is where a configured schedule can
be activated or deactivated.
Frequency Daily Typically, a backup should be carried out
(weekdays, Mondays, daily.
Tuesdays, Wednesdays, ...)
Time Hour: Minute Time of day at which the backup should
start
Table 7 Input fields in the HiPath 4000 Assistant Backup & Restore schedule
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore

Archive AP backup server Only this value is permitted - AP backup
server must already have been
configured.
S Yes Synchronize before backup, i.e. perform
UPDATE.
Must be set to Yes so that the latest
version of the database is saved.
V Yes/No Backup data verification
O Yes/No One File Backup
I Yes/No Include installation partition
Table 7 Input fields in the HiPath 4000 Assistant Backup & Restore schedule
To perform more than one backup a day, enter additional daily backups in the
schedule, for example, one backup at 12 noon and an additional one at 6pm.
• Add New- The new entry is saved in the timetable. A backup is performed
according to the configuration.
This completes configuration on the HiPath 4000 host system.
The time required for a backup procedure depends heavily on the amount of data
to be transferred and the transmission bandwidth available between the host
system and the AP backup server. The procedure takes at least one hour.
3.1.3 Performing the First Backup

So that as little time as possible is lost before the CC-APs can collect the data, it
may be useful to initiate a backup immediately, i.e. outside of the configured
schedule.
Do this by selecting a schedule for AP Emergency and clicking Start now.
The first system backup takes the longest, because all saved data (approximately
100 MB) must be transferred to the AP backup server for the first time. The time
required is also heavily dependent on the available bandwidth in the IP network
between the HiPath 4000 host system and the AP backup server.
3.1.4 Using HiPath 4000 Assistant Backup & Restore

for more extensive Changes in the System
If you need to make extensive changes to the system, or if you are importing a
new system version, the following requirements could arise:
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
• Larger configuration changes should be distributed to all CC-APs as quickly

as possible
– After completing the changes, you should initiate an “unscheduled“

backup. However, make sure that you verify that there is sufficient
transmission bandwidth available in the network at this time to complete
the backup and the subsequent restore operations of the CC-APs.
Remember that you cannot cancel backup and restore procedures that
are active.
It may be useful to deactivate the backup process before making the
changes. -> See the second point.
In the HiPath 4000 Assistant Backup & Restore, go to the schedule for the
backup type “AP Emergency“ and click Start now. It is not advisable to
use “Backup“ for this. If you do, you must remember to run an EXEC-
UPDAT beforehand.
• You should verify new SW (regardless of whether it is a pre-revision bug fix

of an LW or a new system version) on the host system first, before distributing
it to all CC-APs.
– Before importing new SW: 

backup type “AP Emergency“ and change the status from “activated“ to
“deactivated“. If there are several entries in the schedule for the backup
type “AP Emergency“, you must deactivate all entries that could apply
during the planned interval.
– After successful verification of the SW: 

backup type “AP Emergency“ and change the status from “deactivated“
back to “activated“. If there are several entries in the schedule for the
backup type “AP Emergency“, you must activate all entries that you
previously deactivated.
If the network allows it, it may be useful to initiate an unscheduled backup.
-> See the first point.
3.1.5 Checking the Regular Activities of HiPath 4000

Assistant Backup & Restore
In addition to the “usual“ methods (log files etc.), there is an option for
communication with the backup server to query when and which processor was
last in contact with the AP backup server.
Prerequisite:
“rsta“.
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
HiPath 4000 Assistant Backup & Restore Configuration on the CC-AP/Survivable HiPath 4000 SoftGate
• In the Backup & Restore user interface, select the function Log Files .
Figure 7 HiPath 4000 Assistant Backup & Restore - Select “Log Files“
• Select “Status of Host and All CC-APs“ from the list
Figure 8 HiPath 4000 Assistant Backup & Restore - Status of Host and
CC-APs
The date and time data must be interpreted as follows:
Host: Conclusion of last backup procedure

CC-AP/Survivable HiPath Time of last query on AP backup server 
4000 SoftGate: (normally queries once every 10 minutes)
3.2 HiPath 4000 Assistant Backup & Restore Configuration on the CC-AP/
3.2.1 Configuring the AP Backup Server on the CC-

AP/Survivable HiPath 4000 SoftGate
For the automatic restore of the saved data, you must stipulate where the HiPath
4000 backup data should be retrieved. This requires that you set up the computer,
directory and login data exactly as they were for the AP backup server on the
HiPath 4000 host system (see Section 3.1.1, “Configuring an AP Backup Server
with HiPath 4000 Assistant Backup & Restore”).
• In the Backup & Restore user interface, select the function AP Backup
Server under Administration.
You must now complete the following fields with the same settings as the HiPath
4000 host system:
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
• Protocol (SFTP or NFS) - typically: SFTP
• IP Address or Host Name of the AP backup server.
• Directories on the AP backup server.
• If you selected SFTP as the protocol, you still need to configure the Login
name and the Password for accessing the AP backup server (SFTP server).
If the SFTP server requires an Account, this also needs to be entered.
IMPORTANT: If you want to use as backup directory /.AS/BACKUP/IPDA

for security reasons you should use as ftp login „apeftp“.
• By activating Automatic restore disabled, you can deactivate the restore

process. Activate this switch only temporarily and never forget to deactivate
the switch for routine operation.
• Testing - Save the configuration and test the access to the AP backup server.
This option tests whether the installation works, i.e.
• whether the connection to the AP backup server can be established.
• Login with the configured data is possible
• Access to the configured directory is possible
• Configure - Save the configuration without an access test.

Use this option only when it is still not possible to establish a connection to
the “CUSTOMER“ LAN. 
Make sure that you test the settings once a connection to the “CUSTOMER“
LAN is possible.
Access to the AP backup server has now been configured. The HiPath 4000
Assistant Backup & Restore application on the CC-AP/Survivable HiPath 4000
SoftGate will now immediately start to contact the AP backup server every 10
minutes, check whether a new, completed backup set is available, and download
and activate the modified sections of the backup set.
IMPORTANT: Before the first restore, HiPath 4000 Assistant Backup & Restore
performs a complete backup on the hard disk.
This backup is used as a reference for determining modified files that must be
retrieved from the AP backup server when the system is restored.
You do have to initiate the backup manually. In addition, you cannot prevent it.
This procedure takes approximately one hour.
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore
The time required for the restore procedure depends heavily on the amount of
data to be transferred and the transmission bandwidth available between the AP
backup server and the CC-AP/Survivable HiPath 4000 SoftGate. The procedure
takes at least a half hour.
3.2.2 Configuring a Routine Configuration Data

Backup to Hard Disk
While the CC-AP/Survivable HiPath 4000 SoftGate draws the essential
configuration data from the host system using restore, a regular backup of the
specific local CC-AP/Survivable HiPath 4000 SoftGate configuration is still
worthwhile. Because changes to the local configuration are rather rare, a weekly
backup is sufficient. When defining the starting time, make sure that this backup
should run at an appropriate time, i.e. after the host system backup and
subsequent restore on the CC-AP/Survivable HiPath 4000 SoftGate.
The example is based on the following plan:
• Start backup of the host system: daily at 10:05pm
• Completion of the CC-AP/Survivable HiPath 4000 SoftGate restore: by

6:30am, at the latest
• Local backup to hard disk: Sundays at 12:05pm
Prerequisite for the configuration:
“rsta“.
• In the Backup & Restore user interface, select the function Schedule.
Figure 9 HiPath 4000 Assistant Backup & Restore: Creating a schedule

for the configuration data backup
A31003-H3160-S104-8-7620, 07/2014
Backup & Restore

Type Data Only this value is permitted
Unit All Only this value is permitted
status Activated This is where a configured schedule can be
activated or deactivated.
Frequency for example, Sundays Typically, a backup should be carried out weekly,
for example, on Sundays.
Time Hour: Minute Time of day at which the backup should start
Archive Hard disk Only this value is permitted
S Yes/No Synchronize before backup, i.e. perform
UPDATE. - Is not necessary in this case.
V Yes/No Backup data verification
Table 8 Schedule input fields for the configuration data backup

Complete setup of the configuration data backup with
• Add New - The new entry is saved in the schedule. A backup is performed
according to the configuration.
A backup procedure takes approx. 10 minutes.
A31003-H3160-S104-8-7620, 07/2014
04_service_scenarios.fm
Service Scenarios
Upgrading the AP Emergency Server (New Fix Release/Minor Release)
4 Service Scenarios
4.1 Upgrading the AP Emergency Server (New Fix Release/Minor Release)

Procedure
The AP emergency computer regularly checks its backup sector for updated
software packages. If there is a new software package there, it is copied to the
AP emergency computer.
Notes
• Upgrade performed via Software Transfer/Software Activation. This will
deliver the patches and upgrade all systems (HiPath 4000 Platform, ADP/
CCA/CCB, HiPath 4000 Assistant, HiPath 4000 CSTA). In such case the
patches are transferred by HiPath 4000 Backup & Restore to APE and
applied there by HiPath 4000 Software Activation.
• If an RMX upgrade was performed by replacing the HD within the context of

the same major release, then the APE integrates both the RMX software and
the HiPath 4000 Assistant software. For this to function a backup is required
including the install partition files. This can be selected under HiPath 4000
Assistant > Software Management > Backup & Restore > Schedule
(Backup schedule for AP Emergency) with I=Y in the last column. This
function is not guaranteed for a software upgrade to a future major release.
• If an RMX upgrade was performed by replacing the HD within the context of

the same major release, then the APE integrates both the RMX software and
the UW7 software (for this to function a backup is required including the new
install partition files, this can be selected under HBR backup schedule for AP
Emergency with I=Y in the last column). This function is not guaranteed for a
software upgrade to a future major release.
• If an RMX upgrade was performed by replacing the HD (major release

switch), then the procedure is the same as a new installation and the APE
integrates only the RMX software. The HiPath 4000 Assistant software is not
upgraded.
• The APE functionality is not dependent on the HiPath 4000 Assistant

version and therefore guaranteed accordingly.
4.2 Replacing the DSCXL2 in the AP Emergency Server

Proceed as follows if there is a fault with the DSCXL2:
A31003-H3160-S104-8-7620, 07/2014
04_service_scenarios.fm
Service Scenarios
Replacing the DSCXL2 in the AP Emergency Server
1. Remove the defective DSCXL2.
2. Install the new DSCXL2.
3. Reinstall the software (see How Tos for APE installation)
IMPORTANT: Please ensure that the software version installed on the AP

emergency server corresponds to the software version of the host system
(same minor or fix release).
4. Load the restore with the assistance of HiPath 4000 Assistant "Backup &
Restore".
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
Spreadsheets - APE Configuration
5 Spreadsheets - APE Configuration

The following spreadsheets are designed to help you perform an Acces Point
Emergency configuration. Each of the sheets has a configuration diagram and a
blank AMO template on one side, and the completed example from the Service
Manual on the other.
The following spreadsheets (with example) are available:
• AP Emergency spreadsheet: configuring a CC-AP
• AP Emergency spreadsheet: emergency group
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
AP Emergency spreadsheet: configuring a CC-AP
APESU:DATA=CCAP,CCAPNO= ....... CC-AP

Central
APESU:DATA=CCAP,IPADDR= . . .
APESU:DATA=CCAP,IPDBITRT=
System
❑ ❑ ❑ ❑ ❑
AUTONEG 10MBHD 10MBFD 100MBHD 100MBFD
HG
HG
Peri-
pheral
Access
Peri- Real-Time IP Network
pheral Router HG
Periph-
CUSTOMER LAN eral
HiPath 4000
AP 3700 IP
ADP
Periph-
IPDA LAN eral
CC-A
IPDA LAN IPDA LAN
CC-AP
CC-B
Data IP Network
CSTA
CUSTOME
Assistant
Router
HiPath 4000 Manager Backup Server
Webmin Base Admin

Backup & RestoreAdministration Customer LAN address of CC-AP
Backup server IP address or host Protocol . . .
name Network mask in customer LAN
. . . ❑ SFTP ❑ NFS
. . .
(Default) router in customer LAN
SFTP: Logon Name (Login) SFTP: Password . . .
......................... .......................
SFTP: (Account)
.......................
Maximum number of simultaneous CC-AP transfers .........
Directory List on Backup Server .......................
Timetable
Mon. Tues. Wed. Thurs. Fri. Sat. Sun.
.. : .. .. : .. .. : .. .. : .. .. : .. .. : .. .. : ..
Two separate networks are shown in the spreadsheet for real-time or data
communication. If one network is used for both communication types, both
routers are identical.
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
AP Emergency spreadsheet: emergency group
Spreadsheet: Emergency Group

EGRPNO Name CCAPNO
Number Name CC-AP
Switch to emergency mode Assigned access points

THRSHLD LTU Weight SWMODE
APNO
Weighting threshold value SINGLE GROUP
q q
Reverting to normal mode q q
SBMODE AUTOmatic MANual q q
Revert mode q q q q
STABLE q q
Stability time [Minutes] q q
q q
Time frame for automatic switchover q q
Hour Minute (offset) q q
Start q q
End q q
SBBEGIN SBOFFSET q q
SBEND q q
q q
q q
q q
q q
q q
q q
q q
q q
q q
Total weight
A31003-H3160-S104-8-7620, 07/2014
05_spread_sheets.fm
A31003-H3160-S104-8-7620, 07/2014
Survivability Unit for AP Emergency
6 Information for network administrators
6.1 Survivability Unit for AP Emergency

The survivability unit integrates a control processor in an access point. A
maximum of 83 survivability units can be integrated in the system with the
maximum 83 access points per system.
The survivability unit processor requires 2 LAN connections in the IP network.
Detailed information can be found in “Section 2 - System Components (Harwdare

& Software) > HiPath 4000 in the Customer LAN > AP 3700 IP/HiPath 4000
Softgate with Survivability Unit in the Customer LAN”.
An “IPDA“ interface is required for the signaling connection with the allocated
access points.
PHY 10/100 Base T - autosensing or can be permanently

set
MAC address Permanently programmed ->sticker
(the higher of the two addresses)
IP address Configured in the HiPath 4000 system, can be set
See Table 3 “TOS values” in document “Gateways HG
3500 and HG 3575”.
4000 system.
system.
Protocols/ports See Chapter 21, “IP Ports” in the document “Gateways
HG 3500 and HG 3575”.
Routing The default host route, which is configured for HG
3575 in the same shelf, is used for the access point.
Firewall The central processor only allows connections to
addresses that it knows, i.e. access points or assigned
service PCs.
Number of connections Up to 83 TCP/IP connections (one per allocated
access point)
An additional “CUSTOMER“ interface is required for remote access by HiPath

4000 Manager and for accessing the file server, which distributes HiPath 4000
central system software and data.
PHY 10/100 Base T - autosensing
A31003-H3160-S104-8-7620, 07/2014
Survivability Unit for AP Emergency

(lower of the two addresses)
IP address Can be configured in the HiPath 4000 Assistant
Routing Configurable
Number of connections TCP/IP connection to file server if required.
Administration via HiPath 4000 Assistant
Security The same as for HiPath 4000 Assisatnt
A31003-H3160-S104-8-7620, 07/2014
07_ape_inst_short_desc.fm
Quick Guide to Setting up an AP Emergency (IPDA)
Introduction
7 Quick Guide to Setting up an AP Emergency (IPDA)
7.1 Introduction
This chapter illustrates an AP Emergency configuration example and its
generation by means of AMOs and HiPath 4000 Assistant. An existing IPDA
configuration is used.
Case distinction:
A distinction is made with an AP Emergency between a direct link and a
networked configuration.
Direct Link means that the AP Emergency and HiPath 4000 host system are in
the same network segment (HiPath LAN Segment).
Networked Configuration means that the AP Emergency and HiPath 4000 host
system are in different network segments.
The following should be noted here:
• If the IPDA shelves in an emergency group are activated via a direct link, their
associated emergency processor must likewise be activated via a direct link.
• If IPDA shelves are activated via a networked configuration, the associated

emergency processor can be activated either via a direct link or networked
configuration.
The configuration of a direct link emergency processor differs only marginally

from that of a networked configuration. It must simply be noted in the case of a
networked configuration that the respective router entries correspond in the
HiPath 4000 Assistants for host and APE.
The following generation example corresponds to the following configuration and

IP situation:
A31003-H3160-S104-8-7620, 07/2014
Introduction
Network: 1.69.31.0
HiPath 4000: 10-69-300 Netmask: 255.255.255.0
IP
ROUTER
1.69.31.254
DIUN2
TRUNK
IP: 1.69.31.70
ROUTER
130.31.254
CC A
AP 98 IP ADR: AP 99 IP ADR:
Assistant
1.30.31.62 1.30.31.69
IP: 1.69.31.212 with netmask: with netmask:
255.255.255.0 255.255.255.0
CC-AP 
SIGNL IPDA
1.30.31.66
NCUI2+ AP 89 CC-AP 
Assistant
1.30.31.222
AP 99 vNCUI
Emergency
Group: 1
1-70-150
CC-AP 99
7348 7301
7349
TRUNK
A31003-H3160-S104-8-7620, 07/2014
Requirement
7.2 Requirement
The IPDA feature is already installed. The relevant parameters are:
HiPath LAN Segment 1.69.31.0, netmask 255.255.255.0

CC-A 1.69.31.70
CC-B Not available
HG3575 - AP98 1.30.31.62, 255.255.255.0
vHG3575 - AP99 1.30.31.69, 255.255.255.0
Assistant - Customer LAN 1.69.31.212
Default Router - HHS 1.69.31.254
Default Router - AP-LAN 1.30.31.254
New IP addresses are required for the Access Point Emergency feature:
eth0 - SLES 1.30.31.220

Portal Access 500 1.30.31.221
Assistant Customer APE 1.30.31.222
CC-C (IPDA Signaling) 1.30.31.66
Licenses must be available in the code word to use AP Emergency.
IMPORTANT: Survivability and AP Emergency must be purchased in order to

use it.
DISPLAY-CODEW;
--------------------------------------------+--------+------+-------+-------+
| UNIT | PUR- | USED | FREE | BL- |
| | CHASED | | | OCKED |
+---------------------------------------------+--------+------+-------+-------+
| OPENSCAPE 4000 V6 FLEX | 12000 | 89 | 11911 | |
| SIGNALING SURVIVABILITY | 83 | 0 | 83 | |
| CC-AP FOR AP EMERGENCY | 83 | 1 | 82 | |
+---------------------------------------------+--------+------+-------+-------+
7.3 Configuration Steps in HiPath 4000

Step 1: Select the signaling IP address of the CC-AP
Requirement: ADD-DIMSU:TYPE=SYSTEM,CCAP=xx;
A31003-H3160-S104-8-7620, 07/2014
Configuration Steps in HiPath 4000
ADD-APESU:DATA=CCAP,CCAPNO=99,IPADDR=1.30.31.66;
IMPORTANT: The CC-AP number must be one of the AP (LTU) numbers that
are configured in the system (usually the AP number, in which the CC-AP is incor-
porated).
Step 2: Configure AP Emergency Group

Requirement: EINRICHTEN-DIMSU:TYP=SYSTEM,APEGRP=xx;
ADD-
APESU:DATA=APEGRP,EGRPNO=1,CCAPNO=99,THRSHLD=0,SBMODE=AUTO,NAME=
"HPA MUC",STABLE=10,SBBEGIN=20,SBEND=6,SBOFFSET=15;
Parameter Description
CCAPNO Number of the CC-AP that controls the emergency group
NAME Name of emergency group
SBMODE Switchback mode: Manual or automatic (the switching interval is
irrelevant with a manual switchback)
SBBEGIN Switching interval: Start (hour) for automatic switchback
SBEND Switching interval: End (hour) for automatic switchback
SBOFFSET Switching interval: Minutes for RSBEGIN and RSENDE
STABLE Stabilization time of LAN connection in minutes
THRSHLD Threshold value for weighting algorithm
Every AP is assigned a "weight" with AMO APESU. If the threshold
value in the emergency group is exceeded, a switchover is made to
this group's CC-AP.
Step 3: Configure AP 98 and 99 for AP Emergency

ADD-APESU:DATA=AP,APNO=98,EGRPNO=1,WEIGHT=0,SWMODE=GROUP;
ADD-APESU:DATA=AP,APNO=99,EGRPNO=1,WEIGHT=0,SWMODE=GROUP;
Step 4: Configure display readout in emergency mode on system telephone

CHANGE-ZANDE:TYPE=ALLDATA,APEDTXT="AP EMERGENCY";
Step 5: Define switching delay

e.g. : if a (HiPath 4000) system RELOAD does not initiate emergency mode, a
switching delay (in minutes) can be configured.
DISPLAY-SIPCO:TYPE=TIMING;
H500: AMO SIPCO GESTARTET
TIMING : 
-------------------------------------------------------------------
PINGTIME ( UEBERW.-ZEIT FUER PAYLOAD PATH QUALITY ) : 60 SEK 
RESTIME ( RESET ZEIT BEI SIGNALING VERB. VERLUST ) : 60 SEK 
SUPVTIME ( UEBERW.-ZEIT FUER SUPERVISORY VERB. ) : 4 SEK 
APESWDLY ( APE UMSCHALTEVERZOEGERUNG. ) : 0 MIN 
ALVTIME ( UEBERW.-ZEIT FUER SIGNALING VERBINDUNG ) : 60 SEK 
A31003-H3160-S104-8-7620, 07/2014
CHANGE-SIPCO:TYPE=TIMING,APESWDLY=<minutes>;
Step 6: Display AP Emergency configuration

DISPLAY-APESU:;
+------------------------------------------------------------------------------+
| AKTUELLE SYSTEMZEIT : 22-06-2012 09:35:47 |
+------------------------------------------------------------------------------+

+------------------------------------------------------------------------------+
| CC-AP: 99 IP ADRESSE: 1 .30 .31 .66 |
+------------------------------------------------------------------------------+
+------------------------------------------------------------------------------+
| AP EMERGENCY GRUPPE: 1 CC-AP: 99 NAME: HPA MUC |
| SCHWELLE: 0 RSMODE: AUTO |
| STABIL: 10 MIN RSBEGIN: 20 H RSENDE: 6 H RSOFFSET: 15 MIN |
+------------------------------------------------------------------------------+
| AP: 98 AP EMERGENCY GRUPPE: 1 CC-AP: 99 GEWICHT: 0 UMSCHALT: GRUPPE |
| KONTROLL-EINHEIT: UNBEKANNT SIGNAL-PFAD: KEIN |
| LETZTE AUFGEZEICHNETE VERBINDUNGS-STATUS-AENDERUNG: |
| |
| HOST-CC: VERBUNDEN: NEIN GETRENNT SEIT: 00-00-0000 00:00 |
| CC-AP: VERBUNDEN: NEIN GETRENNT SEIT: 00-00-0000 00:00 |
+------------------------------------------------------------------------------+
| KONTROLL-EINHEIT: UNBEKANNT SIGNAL-PFAD: KEIN |
| |
| HOST-CC: VERBUNDEN: NEIN GETRENNT SEIT: 00-00-0000 00:00 |
| CC-AP: VERBUNDEN: NEIN GETRENNT SEIT: 00-00-0000 00:00 |
+------------------------------------------------------------------------------+
Step 7: Update the BP database and synchronize local HG3575 database

EXEC-UPDAT:UNIT=BP,SUSY=ALL;
Step 8: Check synchronicity of configuration management

After the setup is finished with AMO APESU, connect to the HiPath 4000
Assistant in the host (e.g. http://1.30.11.212). Verify here first that the
configuration management is in sync with the RMX system. If this is not the case,
an upload must be performed.
To do this, go to Configuration Management > Network > System, click Search

on the displayed page and start the upload if necessary with Action/ Upload.
Step 9: Configure the time server in the host

An exact time is required for many HiPath 4000 functions. The HiPath 4000
should therefore be connected to a time server. As of HiPath 4000 V6 the
procedure here is as follows:
A31003-H3160-S104-8-7620, 07/2014
1. Set up an ssl connection to the SLES (e.g. with putty), in this case to
1.30.31.210.
2. Log in with root/hicom and call yast.
3. Go to System / Date and Time in yast.
4. Set the Region (e.g. Europe) and Time Zone (e.g. Germany). Activate
Hardware Clock Set To UTC and then go to the Change Date and Time
page with Change.
Enter the IP address of the time server here under Synchronize with NTP
Server (in this case 1.50.100.2). Tick Save NTP Configuration and go to
Configure.
5. Activate Advanced NTP Configuration > Now and on Boot. The NTP
service restarts after pressing Ok and yast can be exited again.
6. The RMS time is updated with 

AENDERN-DATE:;
Step 10: Configure the system ID apeftp

Instead of a conventional system ID, the special system identifier apeftp should
be used for transporting the APE backup set. To use apeftp, it has to be released
explicitly. To do this, go to Access Management > System Account
Administration in HiPath 4000 Assistant and unlock the apeftp user and assign
a password.
The same must also be done later in the HiPath 4000 Assistant of the APE
processor because the IDs and passwords are not synchronized via the APE
backup.
Figure 10 Configuring the system ID apeftp in the host
A31003-H3160-S104-8-7620, 07/2014
Step 11: Configure the AP backup server

HiPath 4000 Assistant:
Software Management > Backup & Restore > AP Backup Server
The HiPath 4000 is itself the backup server in this example. The directory /.AS/
BACKUP/IPDA is provided in the system. Now select Test (also includes
configuration).
Figure 11 Configuring the AP backup server in the host
By setting the schedule for the backup, the transfer time to the CC-APs is defined
indirectly. After a maximum of 10 minutes (not controllable) following the backup,
the CC-APs recognize that a more recent backup set is available and
automatically fetch the delta.
The first backup has to be started manually (step 2) with the initial installation in
order to set up the feature fully.
Check the status after the manual backup:
Figure 12 Checking the backup status
A31003-H3160-S104-8-7620, 07/2014
Configuration Steps in the CC-AP
7.4 Configuration Steps in the CC-AP

Step 1: Install AP Emergency on DSCXL2 or HiPath 4000 SoftGate/HiPath
Access 500
1. USB installation of DSCXL2s (Deployment AP Emergency) or HiPath 4000
SoftGate / HiPath Access 500 (Deployment Survivable SoftGate).
2. Connect the monitor/keyboard or connect to the system using a standard IP

address (192.168.0.2). Change the password for root (hicom). Set the IP
address for SLES (default 192.168.0.2) in YaST, set the time server in the
same way as in the host, switch the keyboard from English to German if
appropriate (owing to special characters in the password).
3. Set up the connection to the HiPath 4000 Platform Administration Portal via
YaST. Launch the LAN wizard. As of HiPath 4000 V6 R2, the LAN wizard
contains the initial config for IPDA:
Figure 13 LAN wizard - Selecting the deployment for AP Emergency

installation
Configure the IP address of the portal and the HiPath 4000 Assistant in the
LAN wizard. Please note here that this is about APE addresses and not host
addresses.
If necessary configure the default router.
The IP address of the APE is entered under IPDA-LAN.
A31003-H3160-S104-8-7620, 07/2014
Figure 14 LAN wizard - Entering the customer LAN and IPDA LAN
addresses
Make sure that the checkbox AMO-Initialisierungs-Kommandos senden

(Send AMO initialization commands) is activated in the Internal LAN
section. The RMS configuration AMOs are configured automatically as a
result.
Figure 15 LAN wizard - Send AMO initialization commands
Now configure the IPDA shelf (in this case as HiPath 4000 SoftGate in
Access 500).
A31003-H3160-S104-8-7620, 07/2014
Figure 16 Configuring the IPDA shelf
Step 2: Configure the user ID of the FTP user (apeftp)

The user for the FTP transport (apeftp) must also be activated in the CC-AP and
configured with the same password as in the host.
Figure 17 Configuring the apeftp system ID in the CC-AP
A31003-H3160-S104-8-7620, 07/2014
Step 3: Configure the FTP backup for APE in the CC-AP

Configure the FTP server for the APE backup in the HiPath 4000 Assistant for the
CC-AP. The entries are the same as in the host.
Synchronization of the CC-AP is started immediately with Test.
Figure 18 Configuring the AP backup server in the CC-AP
Step 4: Query the status

The progress can be seen on the HBR status page. With the initial installation, the
CC-AP starts with a backup so that it has a comparison with the host backup.
Immediately afterwards, the CC-AP starts with a restore, which is concluded with
a reload. The CC-AP then starts up automatically. The CC-AP only performs
restores in normal operation. To this end, the CC-AP contacts the AP backup
server every 10 minutes and checks whether a new, complete backup set is
available so as to then download and activate the modified sections of the backup
set.
The time required for the restore procedure depends to a large extent on the
amount of data to be transferred and the transmission bandwidth available
between the AP backup server and the CC-AP. The process takes about half an
hour, but may be shorter if only changes were made ??to the RMX.
Figure 19 Checking the backup status
A31003-H3160-S104-8-7620, 07/2014
Step 5: Output the APE status

DISPLAY-APESU;
H500: AMO APESU GESTARTET

+------------------------------------------------------------------------------+
| AKTUELLE SYSTEMZEIT : 22-06-2012 10:38:14 |
+------------------------------------------------------------------------------+

+------------------------------------------------------------------------------+
| CC-AP: 99 IP ADRESSE:
1 .30 .31 .66 | 
+------------------------------------------------------------------------------+
+------------------------------------------------------------------------------+
| AP EMERGENCY GRUPPE: 1 CC-AP: 99 NAME: HPA MUC |
| SCHWELLE: 0 RSMODE: AUTO |
| STABIL: 5 MIN RSBEGIN: 20 H RSENDE: 6 H RSOFFSET: 15 MIN |
+------------------------------------------------------------------------------+
| KONTROLL-EINHEIT: HOST-CC SIGNAL-PFAD: LAN |
| |
| HOST-CC: VERBUNDEN: JA VERBUNDEN SEIT: 22-06-2012 10:07 |
| CC-AP: VERBUNDEN: JA VERBUNDEN SEIT: 22-06-2012 10:07 |
+------------------------------------------------------------------------------+
| KONTROLL-EINHEIT: HOST-CC SIGNAL-PFAD: LAN |
| |
| HOST-CC: VERBUNDEN: JA VERBUNDEN SEIT: 22-06-2012 10:08 |
| CC-AP: VERBUNDEN: JA VERBUNDEN SEIT: 22-06-2012 10:08 |
+------------------------------------------------------------------------------+
7.5 Verification and Acceptance of the AP Emergency Configuration

It is essential that the function of the AP Emergency configuration be verified by
an acceptance test after the initial startup and after substantial modifications.
To this end, each emergency group must be switched over once to the CC-AP for
administration. In emergency mode, it must then be verified that communication
with the trunk and with other systems in the network as well as among emergency
groups at different CC-APs functions as planned. Where applicable, installed
applications that support emergency operation should also be included in the test.
Also verify the communications capability of access points that can be switched
to the CC-AP independently of the emergency group when the group is running
in normal mode.
You can conduct the tests when the system load is low.
The following manual switching options are available:

• all access points of all emergency groups of all CC-APs in the system
A31003-H3160-S104-8-7620, 07/2014
EXEC-APESU:SYSMODE=EMERG,LEVEL=SYST; switches to CC-AP

EXEC-APESU:SYSMODE=NORMAL,LEVEL=SYST; switches to central
control
• all access points of all emergency groups of one CC-AP

EXEC-APESU:SYSMODE=EMERG,LEVEL=CCAP,NUMMER=17; switches to
CC-AP
EXEC-APESU:SYSMODE=NORMAL,LEVEL=CCAP,NUMMER=17; switches to
central control
• all access points of one emergency group (of one CC-AP)

EXEC-APESU:SYSMODE=EMERG,LEVEL=APEGRP,NUMMER=1; switches to
CC-AP
EXEC-APESU:SYSMODE=NORMAL,LEVEL=APEGRP,NUMMER=1; switches
to central control
• one access point (of one emergency group (of one CC-AP))
EXEC-APESU:SYSMODE=EMERG,LEVEL=AP,NUMMER=17; switches to 
CC-AP
EXEC-APESU:SYSMODE=NORMAL,LEVEL=AP,NUMMER=17; switches to
central control
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
08_faq_ape.fm
8 FAQs - Frequently Asked Questions

1. Question: When the central system breaks down, an HiPath 4000 system
with IPDA and AP Emergency is divided into 5 islands. Each island is
controlled by a survivability unit. Can islands communicate via IP insofar as
this is permitted by the IP network?
Answer: No. Each island represents an individual system in emergency
mode. These systems only communicate via CO or tie trunks.
Follow-up question: If I configure IP trunking between the islands, will it
work then?
Answer: In principle yes, however, you cannot only configure IP trunking
for emergencies. It must be configured in the central system and is then
also available during normal operation. You must pay particular attention
here that you are dealing with tie trunks in normal operation within a
system, something that is very difficult to manage in terms of LCR.
Therefore, we would strongly advise against such scenarios.
2. Question: Is the Survivable HiPath 4000 Softgate (HiPath Access 500 a/i)
able to take over the control (survival mode) for the local HiPath 4000
Softgate machine in case of a local LAN failure (L1/eth0 down)?
Answer: Yes. On a HiPath Access 500 hardware the signaling routing (HSR)
can be handled on internal path (backplane), i.e. no external LAN needed. If
there are HiPath Access modules connected over Xlink they will continue to
work also.
3. Question: Can Minor/Fixed Release upgrades be made via hard disk

exchange in HiPath 4000 V6 with APEs and Survivable HiPath 4000
Softgates?
Answer: Please note when upgrading a system in the main system via hard
disk exchange e.g. from HiPath 4000 V6 R1.10 to HiPath 4000 V6 R1.12, the
HiPath 4000 Platform Administration (Portal), HiPath 4000 CSTA and HiPath
4000 Assistant1 on APEs and Survivable HiPath 4000 Softgates will not be
automatically upgraded.
Under such circumstances there are two possible courses of action to ensure
the APEs and Survivable HiPath 4000 Softgates receive the correct software
afterwards:
a) The new host system hard disk for the customer upgrade should be
prepared in the lab with the identical version as the existing customer
software level and then upgraded to the version the customer requires via
SWA/SWT. In this way the upgrade history exists on the new hard disk
and with the next HBR for the APE/Survivable HiPath 4000 Softgate the
A31003-H3160-S104-8-7620, 07/2014
08_faq_ape.fm
correct packages will be transferred and an automatic update performed

to the correct HiPath 4000 Platform Administration (Portal), HiPath 4000
CSTA and HiPath 4000 Assistant1 versions.
b) After installation of the new hard disk with a newer version made with First
Installation, RMX would only upgrade on the APEs/Survivable HiPath
4000 Softgates, but HiPath 4000 Platform Administration (Portal), HiPath
4000 CSTA and HiPath 4000 Assistant1 versions will not be updated due
to the missing upgrade history. Once the Fix Release/Maintenance
Release is transferred and activated individually on each APE/Survivable
HiPath 4000 Softgate via SWT/SWA, any subsequent Hot Fixes will be
activated automatically with the next HBR.
IMPORTANT: Linux host HiPath 4000 Platform Administration (Portal) (PLT)

and HiPath 4000 CSTA are not included in this backup. Therefore if host
system is updated by replacing system hard disk, then each connected APE/
Survivable HiPath 4000 SoftGate has to be either installed anew or updated
with RLC of the same version as the new host hard disk.
IMPORTANT: This handling of course does not apply for upgrades from
HiPath 4000 V6 R1 to HiPath 4000 V6 R2 where a new installation is needed.
After installing the central host with HiPath 4000 V6 R2 software, only RMX
would replicate to HiPath 4000 V6R1 APEs/Survivable HiPath 4000
SoftGates, but HiPath 4000 Platform Administration (Portal), HiPath 4000
Assistant and HiPath 4000 CSTA will not be updated.
Therefore the APEs/Survivable HiPath 4000 SoftGates must be newly
installed and then synchronized with the central host.
4. Question: Should Activation of Hot Fixes on APEs and Survivable HiPath

4000 Softgates be made?
Answer: As per SWA graphical user interface activation hints:
ATTENTION: Activation of Hotfixes and FR/MR should not be made directly
on APE Nodes !!!
Software updates should be activated directly on the Host system and will be
mirrored to the APE nodes during the next APE restore process.
Direct activation on APE should only be used in rare instances of first
installation or manual upgrade.
1. Note: HiPath 4000 Assistant Upgrade can be forced via Option I in HBR, however this is not rec-
ommend as standard and would not upgrade the HiPath 4000 Platform Administration (Portal) or
HiPath 4000 CSTA as already commented in the Service Manual.
A31003-H3160-S104-8-7620, 07/2014
dtz_01_feature_description.fm
Feature Description
Different Time Zones (DTZ)
The “IPDA Different Time Zones (DTZ)” feature is used in situations when an
IPDA shelf or access point (AP-IP) or HFA IP telephones are located in different
time zones than the host system. In these cases, the local time of day should be
shown instead of the system time on the display of the digital telephones that are
connected to the remote AP or on the display of the HFA IP telephones.
Example for the local time display:

A HiPath 4000 system in Houston (Texas) has one remote AP in Los Angeles
(California) and one HFA IP telephone in New York (New York). All phones should
display the local time.
Local time (Telephone at AP in Los Angeles) Local time (HFA-IP Telephone in New York)
Monday 23.05.05 / 11:23 a.m. Monday 23.05.05 / 2:23 p.m.
11:23 MO 23.05.05 2:23 MO 23.05.05
IP
System time (Houston)

Monday 23.05.05 / 1:23 p.m.
1:23 MO 23.05.05
Figure 1 Example: HiPath 4000 system in Houston with external telephones

in Los Angeles and New York
The local time is supported for the following functions:

• Date and time of day in the idle display
• Daylight savings time and standard time
• Call list
• Callbacks
A31003-H3160-S104-8-7620, 07/2014
dtz_01_feature_description.fm
Feature Description
• Date/time button
• Date change at midnight
A31003-H3160-S104-8-7620, 07/2014
dtz_02_service_info.fm
Service Information
In the HiPath 4000, you can set up as many as 50 time classes using the AMO
SIPCO. Local times have a fixed offset (in minutes: west or east) to the system
time.
You can assign a time class to an IPDA shelf with the AMO UCSU. In this way,
all Digites that have a display and that are configured on this shelf use this time
class.
You can assign a time class to an HFA station with the AMO SDAT. If an HFA
station that is configured on an IPDA shelf has no time class configured, the time
class of the IPDA shelf is used. As soon as this HFA station is given a time class
with the AMO SDAT, the time class of the IPDA shelf is ignored for this station.
The net must be also defined in AMO SIPCO, if only HFA subscribers are
configured in a differed time zone.
• Using the IPDA wizard in the HiPath 4000 Assistant, the time zones must be
configured before in menu: Configuration Management -> System data ->
IPDA -> IPDA data
• The time class (TCLASS) in AMO SDAT can only be changed for HFA
subscribers.
Restrictions
• „HFA Mobile User“ is not supported. A user’s display shows the time that has
been configured for his or her phone, even if he or she has logged in in a
different time zone.
• Timed reminders are not supported. The timed reminder function is blocked
if a telephone has a local time class configured.
• Call detail recording is done in the system time.
• Error messages are output with the system time.
• In the case of an APE (CCAP) taking over control, it will function in place of
the computer in the host system (CCA/CCB) with a copy of the database from
HHS. If the "Different Time Zones (DTZ)" function (AMO TCLASS) is
configured or if HHS and access points are distributed across multiple
timezones, the APE (CCAP) must be configured to the same time as the HHS
(CCA/CCB/ADP), to ensure correct time display in case of an APE
emergency (CC-AP has taken over control).
A31003-H3160-S104-8-7620, 07/2014
dtz_02_service_info.fm
Service Information
A31003-H3160-S104-8-7620, 07/2014
dtz_03_configuration.fm
Generation Example
3 Generation Example
• The following example covers different DTZ configuration possibilities:
– The HHS is in Houston, Texas and has two AP shelves configured. HFA
stations 4000 and 4001 are in AP shelf 17, which is located in Los
Angeles and assigned time class 1. Because of the different time zones,
AP shelf 17 is given the time class 1, which provides for a time difference
of two hours to the west.
– HFA station 4100 is located in Houston,station 4100 is configured directly

on the HHS. The AP shelf 18 is also located in Houston (Direct link).
Neither AP shelf 18 nor the station configured directly on the HHS
requires a special time class - the default settings are entirely sufficient.
– Although the HFA station 4400 is configured in the HHS in Houston, it is

physically located in New York. This station is given the time class 2,
which means a time difference of one hour in the easterly direction.
– Another configuration option involves the HFA station 4200 that is

configured in AP 18 but that is physically located in Los Angeles.
Therefore the HFA station 4200 has to be assigned to time class 1. 
If the station would be located in New York, the time class 2 has to be
assigned to this station.
– All TDM stations get the time class depending on their locations. Stations
3100, 3101, 3400 and 3401 get the time class of the AP shelf
configuration (AMO UCSU). Station 3300 gets the system time.
– Furthermore, an HFA station could also be configured in AP 17 (in Los

Angeles), but be physically located in New York. Then time class 2 would
have to be configured for this station in the AMO SDAT. This
configuration is not pursued any further in this example.
• Overview diagram for the following configuration possibilities:
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Configuring the Time Classes
3.1 Configuring the Time Classes

• The time classes needed for the example are configured in the AMO SIPCO.
Time class 1, Los Angeleswith automatic switch to standard time, minus 2
hours relative to Houston (system time).
This class supports changes from standard time to daylight savings time and
back; these take place automatically on the last Sunday in March at 2:30 a.m.
and on the last Sunday in October at 3:30 a.m.
The time class and the automatic switches for daylight savings time are
configured as follows:
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Configuring the Time Classes
Configuration Management -> System Data -> IPDA -> IPDA System
Data
CHANGE-
SIPCO:TYPE=TCLASS,TCLASS=1,OFFSET=120,DIRECT=WEST, 
TEXT=”TIME ZONE: -2H
L.A.”,DSTSW=AUTO,MONTHDST=3, 
WKDAYDST=SU,DAYNODST=LAST,HOURDST=2,MINDST=30, 
MONTHDST=10,WKDAYST=SUN,DAYNODST=LAST, 
HOURNT=3,MINNT=30;
Time class 2, New York, with manual switch to standard time, plus 1 hour
relative to Houston (system time).
This class supports changes from standard time to daylight savings time and
back; these take place on March 27th at 2:00 a.m. and on October 30th at
3:00 a.m.
The time class and the manual switches for daylight savings time are
configured as follows:
Configuration Management -> System Data -> IPDA -> IPDA System
Data
CHANGE-
SIPCO:TYPE=TCLASS,TCLASS=2,OFFSET=60,DIRECT=EAST, 
TEXT=”TIME ZONE: +1H N.Y.”,DSTSW=MAN,MONTHNT=3, 
DAYDST=27,HOURDST=2,MINDST=0,MONTHNT=10,DAYNT=30, 
HOURNT=3,MINNT=0;
• The time class configuration now looks as follows:

DISPLAY-SIPCO:TYPE=TCLASS;
TIME CLASS DATE:
---------------------------------------------------------------- 
+------+------------+------------+--------------------+--------+ 
|INDEX | OFFSET | DIRECT | TEXT | DSTSW | 
+------+------------+------------+--------------------+--------+ 
| 1 | 120 | WEST |TIME ZONE: -2H L.A. | AUTO | 
+------+------------+------------+--------------------+--------+ 
| 2 | 60 | EAST |TIME ZONE: +1H N.Y. | MAN | 
+------+------------+------------+--------------------+--------+ 

+------+-----+-------+-----------+-----------+--------+--------+ 
|INDEX | | MONTH | WEEKDAY | DAYNUMBER | HOUR | MINUTE | 
+------+-----+-------+-----------+-----------+--------+--------+ 
| 1 |DST: | 3 | SU | LAST | 2 | 30 | 
| 1 |NT: | 10 | SU | LAST | 3 | 30 | 
+------+-----+-------+-----------+-----------+--------+--------+ 

+------+-----+-----------+------------+------------+-----------+ 
|INDEX | | MONTH | DAYOFMONTH | HOUR | MINUTE | 
+------+-----+-----------+------------+------------+-----------+ 
| 2 |DST: | 3 | 27 | 2 | 0 | 
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Assigning the Time Classes to an AP Shelf
| 2 |NT: | 10 | 30 | 3 | 0 | 
+------+-----+-----------+------------+------------+-----------+ 
3.2 Assigning the Time Classes to an AP Shelf

• The AP shelf 17 configured in the example needs a time class because there
is a station configured on it that draws its time class from the AP shelf.
Assign time class 1 to AP shelf 17.
The time class is configured with the new parameter TCLASS in AMO
UCSU:
Configuration Management -> System Data -> IPDA -> IPDA Access
Point
ADD-UCSU:UNIT=AP,LTG=1,LTU=17, 
LTPARTNO=”Q2305-X40 “,SRCGRP=17,FRMTYPE=INCH19, 
CONNTYPE=APDL,LSRTADDR=198.16.16.63, 
APRTADDR=198.16.16.150,LOCID=017, 
LOCATION=”LOS
ANGELES”,PHONE=3140,FAX=3141,PLCHECK=Y, 
BCHLCNT=120,CONVLAW=N,TCLASS=1;
• The AP 18 is not assigned a time class of its own so that the TCLASS
parameter is not specified. Consequently, AP 18 works with the default time
class 0 (no additional calculation of the display with regard to time zones and
daylight savings time).
IMPORTANT: If the shelf’s time class has to be changed, the shelf must first be
deactivated with the AMO USSU and then reactivated after the change has been
made.
3.3 Assigning the Time Classes to an HFA Station

• A time class must be assigned to HFA stations 4200 and 4400 configured in
the example.
Assigning a time class for HFA stations with AMO SDAT.
After the HFA stations have been configured by means of the AMO SBCSU
(OPTIIP), the time class is configured with the new TCLASS parameter in
AMO SDAT:
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Deleting a Time Class
Configuration Management -> Station -> Station
CHANGE-SDAT:STNO=4400,TYPE=DATA1,NNO=1-1-
100,TCLASS=2;
CHANGE-SDAT:STNO=4200,TYPE=DATA1,NNO=1-1-
100,TCLASS=1;
• HFA stations 4000, 4001 and 4100 are not assigned a time class with AMO
SDAT.
– For HFA station 4000, the calculation is controlled by the time class of the
AP shelf in where the station is currently loggen on (here AP 17, and
therefore time class 1).
– HFA station 4100 is directly logged on to the HHS and therefore does not
need a time class. The display is always adapted to the HHS time.
• HFA subscriber 4200 is configured in AP shelf 18 (system time). Station 4200

is in time class 1, which was assigned to the station with AMO SDAT.
• The HFA subscriber 4400 is configured in Host and is assigned to the Time
Class 2 (TC=2) with AMO SDAT.
• The configured time classes are always shown at station level by the AMOs
SDAT and SBCSU.
• Only an HFA subscriber can be assigned a time class with AMO SDAT. If an
HFA subscriber is assigned time class 0 with AMO SDAT, then the AP shelf’s
time class applies for this subscriber.
3.4 Deleting a Time Class

• You can delete a time class by setting the time offset and direction to the
initialization values.
Delete time class 1.
Reset the offset and direction to delete the time class:
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Deleting the Daylight Savings Time Changeover
Configuration Management -> System Data -> IPDA -> IPDA - System
Data
CHANGE-
SIPCO:TYPE=TCLASS,TCLASS=1,OFFSET=0,DIRECT=NONE;
IMPORTANT: All stations with time class 1 are now using system time!

TIME CLASS DATE:
---------------------------------------------------------------- 
+------+------------+------------+--------------------+--------+ 
+------+------------+------------+--------------------+--------+ 
| 2 | 60 | EAST |TIME ZONE: +1H N.Y. | MAN | 
+------+------------+------------+--------------------+--------+ 

+------+-----+-----------+------------+------------+-----------+ 
|INDEX | | MONTH | DAYOFMONTH | HOUR | MINUTE | 
+------+-----+-----------+------------+------------+-----------+ 
| 2 |DST: | 3 | 27 | 2 | 0 | 
| 2 |NT: | 10 | 30 | 3 | 0 | 
+------+-----+-----------+------------+------------+-----------+ 
3.5 Deleting the Daylight Savings Time Changeover

• You can deactivate the consideration of daylight savings time in the time class
with an AMO parameter.
Deactivate the daylight savings time calculation in time class 2.
Reset the offset and direction to delete the time class.
Configuration Management -> System Data -> IPDA -> IPDA - System
Data
CHANGE-SIPCO:TYPE=TCLASS,TCLASS=2,DSTSW=OFF;

TIME CLASS DATE:
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Changing the System Date/Time with AMO DATE
---------------------------------------------------------------- 
+------+------------+------------+--------------------+--------+ 
+------+------------+------------+--------------------+--------+ 
| 2 | 60 | EAST |TIME ZONE: +1H N.Y. | OFF | 
+------+------------+------------+--------------------+--------+ 
3.6 Changing the System Date/Time with AMO DATE
IMPORTANT: The MODE parameter (DST/ NT) must be specified for DTZ,
otherwise the telephones may display the wrong time.
Changing the system date/time
Base Administration -> Unix Base Administration -> Date/Time
Comment: At present, the MODE parameter can only be entered via RMX.
CHA-
DATE:YEAR=2005,MONTH=7,DAY=20,HOUR=14,MINUTE=30,MODE=D
ST;
• Displaying the system date/time:

DISPLAY-DATE;
+-----------------------------+
| WEDNESDAY |
| DATE: TIME: |
| 2005-07-20 14:30:34 |
| |
| DAY OF YEAR: 201 |
| DAYLIGHT SAVING |
| GMTDIR: TIMEOFFS:0 |
+-----------------------------+
A31003-H3160-S104-8-7620, 07/2014
Generation Example
Changing the System Date/Time with AMO DATE
A31003-H3160-S104-8-7620, 07/2014
dtz_04_amos.fm
Relevant AMOs
4 Relevant AMOs

Language
DATE MODE d Zeit-Modus
MODE e Mode of time
SZ d Sommerzeit
DST e Daylight Saving Time
NZ d Normalzeit
NT e Normal Time
UCSU TCLASS d Zeitklasse des AP-Shelfs
TCLASS e Time class of the AP shelf
SDAT TCLASS d Zeitklasse des Teilnehmers
TCLASS e Time class of the subscriber
SIPCO TCLASS d Zeitklasse
TCLASS e Time class
OFFSET d Zeit-Offset (Minuten)
OFFSET e Time offset (minutes)
RICHT d Richtung (WEST/OST/KEINE)
DIRECT e Direction (WEST/EAST/NONE)
TEXT d Beschreibung der Zeitklasse
TEXT e Time class description
SONUS d Sommer-/Normalzeit-Umschaltung (AUTO/
MAN/AUS)
DSTSW e Daylight savings time switching (AUTO/
MAN/OFF)
MONATSZ d Monat der Sommerzeitumschaltung
MONTHDST e Month of switching to daylight savings time
WOTAGSZ d Wochentag der Sommerzeitumschaltung
WKDAYDST e Weekday of switching to daylight savings
time
TAGNRSZ d Tagesnummer der Sommerzeitumschaltung
DAYNODST e Day number of switching to daylight savings
time
STUNDESZ d Stunde der Sommerzeitumschaltung
HOURDST e Hour of switching to daylight savings time
MINSZ d Minute der Sommerzeitumschaltung
MINDST e Minute of switching to daylight savings time
MONATNZ d Monat der Normalzeitumschaltung
A31003-H3160-S104-8-7620, 07/2014
dtz_04_amos.fm
Relevant AMOs

Language
MONTHNT e Month of switching to normal time
WOTAGNZ d Wochentag der Normalzeitumschaltung
WKDAYNT e Weekday of switching to normal time
TAGNRNZ d Tagesnummer der Normalzeitumschaltung
DAYNONT e Day number of switching to normal time
STUNDENZ d Stunde der Normalzeitumschaltung
HOURNT e Hour of switching to normal time
MINNZ d Minute der Normalzeitumschaltung
MINNT e Minute of switching to normal time
TAGSZ d Tag der Sommerzeitumschaltung
DAYDST e Day of switching to daylight savings time
TAGNZ d Tag der Normalzeitumschaltung
DAYNT e Day of switching to normal time
A31003-H3160-S104-8-7620, 07/2014
signaling_survivability_01.fm
Feature Description
IP Distributed Architecture is an architecture with a central system and numerous
“unintelligent“ peripheral modules. An access point/HiPath 4000 SoftGate is
essentially “remotely controlled“ by the central system. If the control link fails, the
access point/HiPath 4000 SoftGate cannot survive autonomously. It must forward
signaling messages from the peripheral modules to the central system. It cannot
process these itself. Therefore, in the event of a failure in the control link with the
central system, the access point/HiPath 4000 SoftGate has no option other than
to reset itself and wait until the central system restores it to operational status.
Thus, if the control link between the central system and an access point/HiPath
4000 SoftGate fails, the access point/HiPath 4000 SoftGate can no longer place
telephone calls.
On account of these very severe consequences of a failure in the control link

between the HiPath 4000 central system and the access point/HiPath 4000
SoftGate, a possibility of “surviving” such failures has been created. In the event
of a fault, signaling survivability switches the control link from the IP network to
an alternative route. The signaling path is switched over without interruption.
However, signaling survivability does not help against a central system failure. If
a central system is no longer available to control the access points/HiPath 4000
SoftGates, a signaling path via CO or alternative LAN is no help either. In such
cases, the entire communication system (including all access points/HiPath 4000
SoftGates) fails.
Calls possible with signaling survivability:

• Calls within the access point/HiPath 4000 SoftGate
Full scope of features
• Trunk calls from subscribers in the access point/HiPath 4000 SoftGate via
local trunks
Full scope of features (for trunk calls)
• Calls with subscribers in other access points/HiPath 4000 SoftGates to which

an IP connection can still be established for the payload
Full scope of features
A31003-H3160-S104-8-7620, 07/2014
Feature Description
How is the Fault Detected?
Calls with subscribers in the central system and calls with subscribers in access
points/HiPath 4000 SoftGates to which no IP connection can be established for
the payload are only possible if the “Payload Survivability“ feature is configured
for the relevant components. However, even if “Payload Survivability“ is
configured, only “Basic Call“ functionality can be guaranteed.
Please refer IP Distributed Architecture > Section 2.9, “Payload Survivability”.
Signaling survivability is sold as a performance feature and is configured

individually for each access point/HiPath 4000 SoftGate.
For the Signaling Survivability feature the following alternative is available for
each Access Point/HiPath 4000 SoftGate (see also Section 1.2, “What is Used as
an Alternative Route for Signaling?”):
• Signaling Survivability via the public CO
• Signaling Survivability via alternative LAN
IMPORTANT: Please note use of the "HSR over UDP" feature in this regard (see
Section 1.3, “HSR via UDP”).
1.1 How is the Fault Detected?

The control link (-> signaling link) between the CC and access point/HiPath 4000
SoftGate is a TCP connection. Alternatively, it also can be a connection using
UDP packages (feature “HSR via UDP”, see). The original TCP packages are part
of these UDP packages. Therefore, in this case both connection types can be
considered as a TCP connection.
TCP connections (thus also the control link between CC and access point/HiPath
4000 SoftGate) are generally subject to permanent monitoring of their
functionality. Transmitted packets are acknowledged. If the acknowledgement
does not arrive within a certain time, the packet is repeated. In the case a packet
cannot be sent regardless of tcp retransmissions (i.e. no acknowledgement
during defined time frame) the sender must assume packet loss. Even if no
packets are currently being transmitted, TCP checks that the connection is
functional. To this end, so-called “Keep Alive“ messages are sent at
predetermined intervals, which have to be answered.
When a fault is reported on a signaling link, a relatively long period (e.g. more
than 30 seconds) has already passed since the first indication. If it is assumed
that signaling messages for a HiPath 4000 switch have to be delivered within a
specified time (e.g. 60 seconds), the difference between these two times is
available to find and establish an alternative route and re-transmit the messages.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
How is the Fault Detected?
The time can be shortened by drastically reducing the time between the error
index and the message.
Therefore, a supervisory link is always established in HiPath 4000 between the

CC and the access point/HiPath 4000 SoftGate parallel to the signaling link as
soon as signaling survivability is configured for the access point/HiPath 4000
SoftGate.
This supervisory link is used exclusively to exchange “Keep Alive“ messages at

very short intervals (e.g. every second).
If the CC fails to receive a response to a “Keep Alive“ message within a definable

time interval (supervisory time), it switches the routing of the signaling messages
to this access point/HiPath 4000 SoftGate from the IP router to the survivability
router.
“Keep Alive“ Message to

Response from AP
Link failure!
A sec. A sec. A sec. A sec. A sec. A sec. A sec. A sec.
1 2 3 4 5 6 7 8 Rerouting
via the
B seconds Survivability
Supervisory Time route
t
B is the “Keep Alive Time“ of the supervisory TCP connection

which is called Supervisory Time (SUPVTIME), e.g.: 4 s
A is the message repeat interval; (A=B/8) e.g.: 0.5 s
In order to limit the load generated A < 0.5 s
results in a message being sent at most every 0.5 s.
If SUPVTIME = 3 a message is sent 6 times every 0.5 s
before the timer expires.
Figure 1 Supervisory message flow for signaling survivability in the CC
An escalation strategy is also triggered in the access point/HiPath 4000 SoftGate.
An interface fault is reported if, irrespective of the supervisory link, messages do

not reach the access point/HiPath 4000 SoftGate on the signaling link within the
set time interval (ALVTIME), either via the IP network or the alternative route.
After the interface fault report (ALVTIME) the access point/HiPath 4000 SoftGate
is taken out of attendent list and will be reset within a definable time interval
(RESTIME). It then waits for a renewed contact through the HiPath 4000 CC.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
What is Used as an Alternative Route for Signaling?
Up to end of ALVTIME, all signaling messages queued in the CC and in the

access point/HiPath 4000 SoftGate for transmission are buffered. If the alive time
(ALVTIME) expires, it can be assumed that the stored messages are outdated
and may no longer be delivered. However, this means that the message flow
between the CC and the access point/HiPath 4000 SoftGate is no longer
consistent.
The time constants can be changed with the AMO SIPCO in the TIMING branch.
(see IP Distributed Architecture > Section 2.1, “HiPath 4000 LAN Segment” >
System timing (TIMING))
Message Message
to AP to AP
< ALVTIME
ALVTIME
RESTIME
Interface fault in Reset of access

access point/HiPath point/HiPath 4000
t 4000 SoftGate SoftGate
Figure 2 Message flow for signaling survivability in the access point/HiPath

4000 SoftGate
1.2 What is Used as an Alternative Route for Signaling?

If the IP link of an access point/HiPath 4000 SoftGate fails, an alternative route in
a network is required that is not affected by the failure.
The basic demand on the network for the alternative route is simple:
• It must be independent of the IP network whose fault is to be bypassed via

the alternative route.
• A connection device for the access point/HiPath 4000 SoftGate is required,

which acts as a modem. It must be actively callable and provide the access
point/HiPath 4000 SoftGate with “Ring Indication“.
• The central system must be supported by a corresponding router or an

STMI2/4 with WAML function.
As of HiPath 4000 V6 R2 there are two different ways for signaling survivability:
• Signaling Survivability via PSTN Network
• Signaling Survivability via Alternate LAN
A31003-H3160-S104-8-7620, 07/2014
Feature Description
1.2.1 Signaling Survivability via PSTN Network
LTU LTU LTU

Acces Acces Acces
AP 3500
AP 3700 IP
AP 3700 IP
Per Per Per
Per Per Per
LTU
WAN Acces
Centra
AP 3700 IP
Per
PSTN Per
Per
LTU
Acces
Per
LTU
HiPath 4000
AP 3700 IP
Acces
Per
AP 3300
Per Per
Per
Figure 3 IPDA with signaling survivability
With signaling survivability via the PSTN network, an alternative route for
signaling via the ISDN network (PSTN) is set up as soon as a fault in the IP path
is detected. The messages are then routed via a PSTN router to the central
system (for example, router with IP --> S2 or STMI2/4 board with WAML function)
and an ISDN modem on the access point/HiPath 4000 SoftGate. The signaling
messages are sent via this alternative path once it is established (approx.
30 ... 60 seconds). This ensures that none of the messages that may be in a
backlog are lost.
As a rule, an access point/HiPath 4000 SoftGate with signaling survivability

generally requires a telephone connection for this purpose. The connection
should be in the public PSTN network. Alternatively, it may be in a private
network, insofar as the connection is not routed via the (IP) network whose fault
is to be bypassed via the alternative route.
IMPORTANT: The modem may not access the public network via the access
point/HiPath 4000 SoftGate. It requires a separate connection independent of the
access point/HiPath 4000 SoftGate. 
If the LAN connection fails, the access point/HiPath 4000 SoftGate can no longer
be controlled.
If the alternative route to the modem is routed via the access point/HiPath 4000
A31003-H3160-S104-8-7620, 07/2014
Feature Description
SoftGate, it cannot be switched before the alternative route is activated. However,

the alternate route cannot be activated before being switched in the access point/
The access point/HiPath 4000 SoftGate is equipped with an RS 232/ V.24

interface on the HG 3575 module in order to connect a modem, via which the
alternative signaling route into the telephone network is routed.
The counterpart to this modem is a special router at the HiPath 4000 LAN
segment, referred to here as the survivability router. This router also requires
access to the telephone network.
If the LAN/WAN-based connection to the access point fails, a modem connection

is established via CO. The access point is controlled via this connection until the
LAN/WAN connection is reestablished.
If every access point features an individual modem (and the central system has
reserved enough router connections via CO (PSTN)), signaling survivability can
cover even the total failure of the WAN infrastructure. The only critical factor here
are the connection between the active CC and the survivability router(s) in the
HiPath 4000 LAN segment and the independence of (failed) WAN from the PSTN
used for survivability.
Details on the transmission methods between router and modem:
The transmission methods between the router and the modem must be
compatible. Whenever possible, a digital link between the router and the modem
should be used (ISDN modem), as analog modems require a long time to
measure the route and agree on a transmission method. If the supervisory timer
of the CC or access point/HiPath 4000 SoftGate expires during the link
establishment time, there is a danger of messages being lost. The access point/
HiPath 4000 SoftGate then resets itself. In addition, transmissions rates are
substantially lower with analog modems than via ISDN. This can lead to delays
with signaling messages and to the supervision timer expiring during bottleneck
situations, in which case the access point/HiPath 4000 SoftGate resets itself in
the end.
Approximately 64 Kbps are generally considered to be sufficient for the maximum

transmission capacity required in the signaling path. The transmission rate
offered by ISDN modems comes sufficiently close to this value. In the case of
analog modems, at most half of the transmission bandwidth can be achieved.
This can lead to the limitations described. A transmission bandwidth of at least
28.8 Kbps must be guaranteed. A path is considered unsuitable for survivability if
a lower bit rate is used for modem connects due to low-quality links.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
1.2.2 Signaling Survivability via Alternate LAN

With signaling survivability via alternate LAN, an alternative route for signaling via
a second LAN path is set up as soon as a fault in the IP path is detected. Therefor
a survivability router on the central system and a second LAN infrastructure on
on the access point/HiPath 4000 SoftGate must be available. Then an alternate
path is set up via the survivability router on the central system and the second
LAN on the access point/HiPath 4000 SoftGate. The signaling messages are sent
via this alternative path once it is established. This ensures that none of the
messages that may be in a backlog are lost.
There are two possible scenarios for signaling survivability via alternate LAN:
• Using L2 Redundancy at access point/HiPath 4000 SoftGate for input of

alternative router
Figure 4 Signaling Survivability über alternatives LAN und L2 Redundanz
• Using 2nd ethernet interface of access point/HiPath 4000 SoftGate for input
of alternative router
Figure 5 Signaling Survivability über alternatives LAN und zweiter

Ethernet-Schnittstelle
A31003-H3160-S104-8-7620, 07/2014
Feature Description
HSR via UDP
If every access point/HiPath 4000 SoftGate features an individual survivability

router, signaling survivability can cover even the total failure of the WAN
infrastructure. The only critical factor here are the connection between the active
CC and the survivability router(s) in the HiPath 4000 LAN segment and the
independence of (failed) WAN from the LAN used for survivability.
1.3 HSR via UDP
IMPORTANT: The feature “HSR via UDP” has been released with HiPath 4000
V6 R2 and higher!
The "HSR (HiPath Signaling Router) over UDP" feature
• concerns the signaling connection between the host system and Access
Point/HiPath 4000 SoftGate. The signaling connection between APE and
Access Point/HiPath 4000 SoftGate is not affected. The latter is always only
a pure TCP/IP connection regardless of the configuration of the SIGMODE
parameter in AMO UCSU.
• can/may be activated additionally for "Signaling Survivability via the public

CO" in order to bypass firewalls.
• must be activated for using the "Signaling Survivability over alternative LAN"
feature.
• can/must be activated/deactivated individually for each Access Point/HiPath

4000 SoftGate (AMO UCSU, SIGMODE=HSRUDP).
IMPORTANT: The customer IP network (firewall) must not block the UDP 4000
and 4050 ports.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• The feature “Signaling Survivability” is released for access points, HiPath
4000 SoftGate and HiPath Access.
• Up to 10 survivability routers can be configured in the system.
• Signaling survivability via PSTN network (modem) with HiPath 4000 Softgate
(vNCUI) is supported for SoftGate 50 and SoftGate 500.
• Only valid for signaling survivability via PSTN network: Depending on

the connection capacity, a survivability router can operate up to 30 access
points/HiPath 4000 SoftGates (router with S2 connection). As it cannot be
foreseen precisely where in the IP network a fault will occur, the router
capacity must be designed for the worst case scenario, i.e. failure of the link
from the HiPath 4000 LAN segment to the IP network of the customer. In such
a case, alternative signaling routes will be needed immediately for all access
points/HiPath 4000 SoftGates with signaling survivability.
• Only valid for signaling survivability via PSTN network: If the modem
connection goes over the public network, connection charges will accrue.
The link to an access point/HiPath 4000 SoftGate is used as long as the
access point/HiPath 4000 SoftGate is not accessible via the IP network.
The configuration of the survivability router contains a setting for the period of
“non-use“ after which this link is disconnected. This “hold-time“ does not form
part of the IPDA configuration.
Accessibility of the access point/HiPath 4000 SoftGate via the modem
connection is checked on a cyclical basis (RTO). The check can also be
started directly using the AMO TSU.
In these cases too, charges for the link will accrue in the PSTN.
• The connection from the active processor (CC-A or CC-B) to the survivability
router runs via the HiPath 4000 LAN segment, just like the connection to the
normal LAN router. If this LAN segment fails, for instance because a central
L2 switch is faulty, the signaling survivability function will also fail. This “single
point of failure“ can be somewhat mitigated if CC-A and CC-B are connected
to different L2 switches and, for example, half the survivability routers and half
the HG 3500 are each connected to the relevant switches. This ensures that
at least half of the system will still be available should one of the two L2
switches fail.
• The TCP stream (tcp.port=4000) has to be routed fully transparently through

the customer's IP network (i.e. no manipulation of the SequenceNumber
etc.), otherwise the "Signaling Survivability" will not work. Furthermore, any
available firewalls have to be configured accordingly so that no SequenceNo
and SYN check takes place for the tcp.port=4000. It this cannot be
guaranteed, the "HSR over UDP" feature should be activated alternatively.
A31003-H3160-S104-8-7620, 07/2014
Service Information
• Signalling survivability via PSTN network (modem) with HiPath 4000

SoftGate (vNCUI) is tested and supported with HiPath 4000 SoftGate 50 &
HiPath 4000 SoftGate 500. Both startup and basic scenarios with high load
are tested (480 subscribers with > BHCA 6000) via modem, however the use
of any large group signalling features (e.g. AUN) may lead to signalling
delays. The delays are not one of the feature itself, however an issue of
Bandwidth Limitation of the PPP connection (64kbit/s) that can lead to TCP
Retransmission. If large groups with signalling are in use, or HiPath 4000
SoftGate 1000 is used, for HiPath 4000 V6 R2 and higher it is recommended
to use "Signalling Survivability via alternate LAN" where there are lesser
bandwidth concerns (i.e. ADSL access has much higher available bandwidth
for signalling). Other survivable options like APE, Survivable HiPath 4000
SoftGate and BPOOL functions are also available, but not without interruption
to telephony.
Please also note:
– To assure signaling survivability at the HiPath 40000 SoftGate a certain

USB cable is necessary (Part number: C39195-Z7705-A3).

If you are unsure, the correct type of cable will display "New USB device
found, idVendor=067b, idProduct=2303" in \var\log\messages under
Linux.

An alternative cable from ATEN is known to cause problems. This has the
vendor id "New USB device found, idVendor=0557, idProduct=2008".
– To assure signaling survivability at the HiPath 40000 SoftGate functions

with an external ISDN router, the ISDN modem must have a minimum
firmware version of V7.019 to understand the AT**ACCM command. For
further details, please see MSC24547 in G-DMS.
• Signaling Survivability with WAML-Replacement is only released for

Common Gateway Boards (HG 3500). Thus, the WAML function can only be
configured in a host shelf, i.e. the functionality at an IPDA shelf (“direlct link”)
/ HiPath 4000 SoftGate / HiPath Access is not supported.
• Using L2 redundancy at access point for input of alternative router is only

possible with HiPath 4000 SoftGate.
• In case of signaling survivability via alternate LAN (AMO APRT, parameter

ALTLAN) HSR over UDP must be configured.
• Restrictions and information with the deployment “Simpley with integrated

SoftGate” (HiPath 4000 SoftGate on same computer as host system):
– The integrated HiPath 4000 Softgate doesn’t support HSR over UDP.
– The integrated HiPath 4000 Softgate doesn’t support Signaling

Survivability function for HSR connection.
A31003-H3160-S104-8-7620, 07/2014
Service Information
– The integrated HiPath 4000 Softgate is allowed to accept a HSR

Connection from an AP-CC (feature APE).
• Restrictions and information with the deployment “Survivable SoftGate”

(HiPath 4000 SoftGate and APE on the same computer):
– APE doesn’t support Signaling Survivability function for HSR connection.
– HiPath 4000 Softgate supports HSR over UDP to the host system.
– HiPath 4000 Softgate supports Signaling Survivability function for HSR

connection to the host system.
• The golden load loadware of the NCUI board doesn’t support UDP
functionality which is necessary for signaling survivability via alternate LAN.
Thus, follow the instructions in Section 3.2.4, “Replacement of a defect NCUI
Board with a new NCUI Board” when replacing a board.
A31003-H3160-S104-8-7620, 07/2014
Service Information
A31003-H3160-S104-8-7620, 07/2014
Signaling Survivability via PSTN Network
3.1 Signaling Survivability via PSTN Network
3.1.1 Configuring the HiPath 4000
AP 99
HG
STMI-1 STMI-2
Peripheral
HG 3575 Boards
3500
Ra Rx AP 3300 IP, AP 3500/3505
Router Router 192.168.15.98

HG
AP 98
3500 HG Peripheral
3575 Boards
I P Ne two r k 030-3217654
AP 3300 IP, AP 3500/3505
Peripheral
Boards
192.168.15.43
Ry
AP 43
HG Peripheral
Router 3575 Boards

069-7654321
LSADDR AP 3300 IP, AP 3500/3505
Atlantic LAN
ADP 192.168.1.101
192.168.15.1 192.168.15.18
AP 18
HG Peripheral
3575 Boards
CC-A R1 7123456
Router P S TN Ne twor k AP 3300 IP, AP 3500/3505
SURVNET
192.168.15.0
AP 17
3575 Boards
Router
192.168.15.10
AP 3300 IP, AP 3500/3505
CSTA LSADDR
192.168.1.110
Assis
tant
HiPath
4000
Figure 6 Signaling survivability via Modem
The access connections of the survivability routers and modems into the PSTN
telephone network form a virtual IP network, the survivability network. Every
access to this virtual network requires an IP address in this network. In order to
keep the administrative effort for this network to a minimum, a number of
stipulations have been agreed on:
• The survivability network has the netmask 255.255.255.0.
• A maximum of 10 survivability routers are supported between the HiPath

4000 LAN segment and the survivability network; these are numbered
consecutively from 1 to 10. The fourth digit in the IP address of routers in the
survivability network is the consecutive number of the router, i.e. 1-10.
A31003-H3160-S104-8-7620, 07/2014
• The address of an access point in the survivability network is likewise

specified. The fourth section of the IP address is set to be identical to the LTU
number of the access point.
Thus, only one parameter essentially remains to be configured in the survivability

network: the network address.
This is configured with the AMO SIPCO and must already be specified during
ADD-SIPCO if the customer has purchased signaling survivability licenses (see
IP Distributed Architecture > Section 2.1, “HiPath 4000 LAN Segment”).
If the licenses for signaling survivability are not purchased until later or if the zero
address 0.0.0.0 was specified during initial installation, this address must be set
now.
Data
Click Search, enter or change the survivability network address on the
System Data tab, then Save.
CHANGE-SIPCO:TYPE=LSNET,SURVNET=192.168.15.0;
IMPORTANT: The last digit of the SURVNET address must always be ZERO.
Otherwise, it would not be a network address, together with the specified netmask
255.255.255.0.
The licenses for signaling survivability can be queried as follows:
Configuration Management --> HiPath Inventory Management

--> HIM System Data --> Feature --> Marketing Units
Click Search --> Sales Features tab --> Signaling Survivability entry
DISP-CODEW; “SIGNALING SURVIVABILITY“ entry
Although this network is only used when needed and the communication partners
are fixed, the address for this network must be agreed on with the customer
network administrator.
Thought now has to be given to the assignment of access points to survivability

routers. Every survivability router can be described through the following data,
which must also be configured in the router itself:
• Consecutive number of the router [1..10]
• IP address of the router in the HiPath 4000 LAN segment
• IP address of the router in the survivability network
• Access points to be operated via this router, including:
A31003-H3160-S104-8-7620, 07/2014
• LTU number and, derived from that number, its IP address for survivability
• Telephone number of the modem connection
• Signaling survivability type = MODEM
Ultimately, the router is to be configured in such a way that, upon receipt of a

packet with a target address identical to that of the survivability address of an
access point, it establishes a dial-up connection to the modem of that access
point and subsequently transmits the packet. If the connection is not used for an
extended period (e.g. 30 seconds), the access point can be reached again via
LAN and the link to the modem can be disconnected.
An STMI2/4 module with WAML function in the HiPath 4000 CC can also be used
as a survivability router.
IMPORTANT: If a survivability router is to access the ISDN network via the

HiPath 4000, there must be sufficient connection capacity in the trunk access of
the HiPath 4000.
If, for example, 83 access points on a system are equipped with signaling surviv-
ability, 83 B-channels to the CO must be made available immediately in the
central area around the HiPath 4000 system in the event of an IP network failure.
If this capacity is not reserved, it may not be possible to reach all access points.
Access points that are not reached via signaling survivability perform a restart
and can only operate again if they are accessed by CC via LAN or modem.
The configuration in the HiPath 4000 switch is realized as follows:
• Announce the survivability routers in the system

Click Search, enter or change the router number and address on the Router
LSADDR=192.168.1.101;
LSADDR=192.168.1.110;
Routers 1 and 10 from the example in Figure 6 “Signaling survivability via

Modem” are thus configured.
• Assign the access points to the survivability routers
Point
Click Search, set the desired router number on the General tab under
signaling survivability and Save.
A31003-H3160-S104-8-7620, 07/2014
ADD-
APRT:TYPE=SURV,CONF=AP,LTU=98,ROUTERNO=1,SURVTYPE=MODE
M;
ADD-
M;
ADD-
M;
Thus, all access points with signaling survivability in the example in Figure 6
“Signaling survivability via Modem” are assigned to a router. Finally, when
assigning the access points to a router, signaling survivability for the respective
access point is configured. This command checks whether a license for signaling
survivability is available. If so, the use is booked; if not, the configuration is
rejected.
If the assignment of an AP to a survivability router is changed, e.g. if AP 43 should

in future be operated by Router 10 instead of Router 1, the following action is
required:
Point
Data
A CHANGE of the configuration for signaling survivability with APRT is not
possible. In order to change the configuration, the corresponding
assignment is simply deleted and subsequently re-configured.
ADD-
APRT:TYPE=SURV,CONF=AP,LTU=43,ROUTERNO=10,SURVTYPE=MOD
EM;
In order for this change to become effective, AP 43 has to be restarted.

system hard disk.
A31003-H3160-S104-8-7620, 07/2014
3.1.2 Configuring the Modem

In order to be able to make the configuration settings, the modem must be
connected to a PC and a terminal emulation program (HyperTerminal) must be
started on the PC.
IMPORTANT: The Pocket ISDN TA modem from INSYS Microelectronics,

S30122-X7551-X AYA422 is recommended for use as an IPDA survivability
modem with ISDN interface.
The following must be set if they were not already set by default:
• The baud rate at the modem’s serial interface must be set to 115200 bauds
which is mostly covered via the auto-detect mode.
Modems that do not support the 115200 baud rate at the serial interface
are unsuitable for use with IPDA.
• Auto-Answer must be switched off.
• The local echo must be switched off.
• The modem response to commands must be shown in plain text (in long
form), i.e. as text “RING“, “CONNECT“, etc.
• Neither error correction nor compression must be activated in the modem.

This is performed by the PPP itself.
• The software handshake (XON/XOFF) must be deactivated.
• For ISDN modems: the B-channel protocol: HDLC - PPP protocol

(“async to sync“ conversion, asynchronous PPP, single link PPP)
• For analog modems: set the line bit rate permanently on both modems to
save negotiation time.
In response to the modem’s “RING“ message, the HG 3575 sends the “AT A“
command to the modem which must report “CONNECT“ within 60 seconds.
First the factory defaults must be restored

AT&F =
The parameters specified above must then be set
For modem Pocket ISDN TA
• Auto-Answer must be switched off:

ATS0=0 =
• The local echo must be switched off:
ATE = or generally ATE0 =
A31003-H3160-S104-8-7620, 07/2014
3.1.3 Configuring the Router
3.1.3.1 Signaling Flow Survivability for “Networked“ Access

Points
CC-A Ra Rx AP 98
192.168.1.254
192.168.23.1
192.168.1.1 192.168.23.98
192.168.15.98
R1
Modem
192.168.1.101 192.168.15.1
Figure 7 Survivability router configuration
The following process must be taken into consideration when configuring the
survivability router.
Normal operation (without survivability):

CC-A generates packet at AP 98 with destination 192.168.23.98 and source
192.168.1.1 and transfers it to the Ra router (192.168.1.254).
This may send the packet via another router to Rx which delivers the packet
to AP 98.
Survivability:
192.168.1.1 and transfers it to the router R1 under 192.168.1.101.
IMPORTANT: The complete IP frame, including addresses, remains

identical to the frame in normal operation.
With survivability, only the accessed router changes (in the HiPath 4000 LAN
segment). This change takes the form of a different destination address at
Ethernet level (MAC-DA). 
The IP address of Router R1 in the HiPath 4000 LAN segment is not accessed
visibly. It is needed to determine the MAC address of the router port with ARP.
A31003-H3160-S104-8-7620, 07/2014
3.1.3.2 Signaling Flow Survivability for “Direct Link“ Access

Points
CC-A AP 18
192.168.1.1 192.168.1.18 Router 192.168.200.9
192.168.15.18
R1
Modem
192.168.1.101 192.168.15.1
Figure 8 Survivability router configuration
The following process must be taken into consideration when configuring the
survivability router.
Normal operation (without survivability):

CC-A generates packet at signaling unit AP 18 with destination
192.168.200.9 and source 192.168.1.1 and transfers it to the internal
signaling router associated with AP 18 (192.168.1.18).
This sends the packet to the signaling unit AP 18 (192.168.200.9).
Survivability:
192.168.1.1 and transfers it to the router R1 under 192.168.1.101.
IMPORTANT: The complete IP frame, including addresses, remains

identical to the frame in normal operation.
With survivability, only the accessed router changes (in the HiPath 4000 LAN
segment). This change takes the form of a different destination address at
Ethernet level (MAC-DA). 
The IP address of Router R1 in the HiPath 4000 LAN segment is not accessed
visibly. It is needed to determine the MAC address of the router port with ARP.
R1 sends the packet to the next hop router 192.168.15.18 and creates the
modem link for the PPP connection between 192.168.15.1 and
192.168.15.18 or uses the existing connection.
The packet is sent from the PPP instance 192.168.15.18 to the destination
192.168.200.9 in AP 98.
For this, the route for 192.168.200.9 must be configured via 192.168.15.18 in the
survivability router R1 and the dial-up connection for the destination
192.168.15.18.
A31003-H3160-S104-8-7620, 07/2014
The PPP instance in R1 must be configured with the address 192.168.15.1 so that
packets from AP 18 can be transported back to CC-A.
3.1.3.3 Signaling Survivability with WAML Replacement
For the feature “Signaling Survivability with WAML Replacement “ a common

gateway board (HG 3500) must be configured in the AMO BFDAT using
FUNCTION=WAML. Either a separate board or a board that supports multiple
functions can be used for this purpose.
IMPORTANT: If this feature is configured (STMI board with WAML function),

then the redundant LAN interfaces function does not work. See also Section 6.4,
“Redundant LAN Interface”.
Hardware:
• STMI (HG 3500) with WAML functionality is used as a router. It must be
configured in the host system in order to communicate with CCA/ CCB (within
the same network).
• S0 connection has to be configured.
• Modem ISDN connected with V.24 (modem) at NCUI (HG 3575).
Figure 9 Signaling survivability withWAML replacement
The configuration consists of 3 parts:
A31003-H3160-S104-8-7620, 07/2014
1. IPDA
ADD-
SIPCO:NETADDR=172.28.145.0,NETMASK=255.255.255.0,IPMODE=IPV4,DEF
RT=172.28.145.254,CCAADDR=172.28.145.150,CCBADDR=0.0.0.0,SURVNET
=192.168.15.0;
ADD-UCSU:UNIT=AP,LTG=1,LTU=18,LTPARTNO=Q2305-
X40,SRCGRP=1,FRMTYPE=L80XF,CONNTYPE=APDL,LSRTADDR=172.28.145.155
,APRTADDR=172.28.145.254,LOCID=012,LOCATION="IPDA17WEAS",PLCHECK
=YES,BCHLCNT=30,CONVLAW=NO,TCLASS=0,ALARMNO=0;
ADD-
APRT:TYPE=APNET,LTU=18,APIPADDR=172.28.0.57,NETMASK=255.255.255.
255,TAIPADDR=0.0.0.0;
/* HG3575 Configuration data
ip_addr_eth is * 172.28.145.155
netmask_eth is * 255.255.255.0
default_gateway is *1 172.28.145.254
ip_addr_signaling is * 172.28.0.57
netmask_signaling is * 255.255.255.25
5
ip_addr_survivability is *2 192.168.15.18
netmask_survivability is *2 255.255.255.0
gateway_survivability is *2 192.168.15.1
netmask_hhs is * 255.255.255.0
ip_addr_CC_A is * 172.28.145.150
ip_addr_CC_B is *3 0.0.0.0
ip_addr_CC_C is 0.0.0.0
2. Signaling Survivability with WAML
/* WAML
ADD-BFDAT:FCTBLK=5,FUNCTION=WAML,BRDBCHL=BCHL60&BCHL120;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=5,FUNCTION=WAML,BCHLCNT=1;
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=1,SLOT=85,PARTNO="Q2316-
X10",FCTID=1,LWVAR="0",FCTBLK=5,BCHLWAML=10;
ADD-
CGWB:LTU=1,SLOT=85,SMODE=NORMAL,IPADR=172.28.145.156,NETMASK=255
.255.255.0;
/* Direction to the router and call number of the router
ADD-BUEND:TGRP=111,NAME="WAML",NO=30;
ADD-
COT:COTNO=222,PAR=ANS&LWNC&DFNN&NTON&NLCR&NLRD,INFO=FUER_WAML;
A31003-H3160-S104-8-7620, 07/2014
ADD-
COP:COPNO=222,PAR=SFRM,TRK=TA,TOLL=TA,DEV=LAN,INFO=COP_FUER_WAML
;
ADD-COSSU:NEWCOS=222,AVCE=TA&TNOTCR;
ADD-WABE:CD=446,DAR=TIE,CHECK=N;
0,COTNO=222,COPNO=222,COS=222,LCOSV=1,LCOSD=1,CCT=WAMLREPLACED,D
ESTNO=0,PROTVAR=ECMAV2,SEGMENT=8,NNO=1-1-
318,TGRP=111,DEV=HG3550LA,BCHAN=1&&10;
ADD-
RICHT:MODE=LRTENEW,LRTE=223,LSVC=ALL,NAME=WAML,TGRP=111,DNNO=1-
1-118;
ADD-LODR:ODR=11,CMD=ECHO,FIELD=1;
ADD-LODR:ODR=11,CMD=END;
ADD-LODR:ODR=11;
ADD-LDAT:LROUTE=223,LSVC=ALL,LVAL=1,TGRP=111,ODR=11,LAUTH=1;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=446,LROUTE=223,LAUTH=1;
/* IP address of the router (IP address of the physical router – WAML)
ADD-APRT:TYPE=SURV,CONF=ROUTER,ROUTERNO=1,LSADDR=172.28.145.156;
/* Assign access point to the survivability router
3. WAML (HG 3500/STMI) configuration with WBM
WAML and LAN Redundancy

If WAML functionality is configured there is no LAN redundancy at all despite the
configuration of the LAN2 active or not.
Therefore select during initial setup (Wizard > Initial Setup) Not configured or
deactivated.
Figure 10 WAML replacement - Second LAN
Router Call Number

Explorers > Routing > PSTN > (right mouse click) Edit Global PSTN Data ->
Router Call Number “446” as configured in AMO LDPLN.
A31003-H3160-S104-8-7620, 07/2014
Figure 11 WAML replacement - PSTN global data
You can check the result with Explorers > Routing > PSTN > Display Global
PSTN Data.
PSTN Peer
The PSTN Peer (PSTN-Partner) ist the survivability-modem with its IP-Address
coming from AMO SIPCO, parammeter SURVNET + access point number, here
192.165.15.18.
The PSTN-interface is the PPP side of the WAML, i.e. AMO SIPCO, parameter
SURVNET + router number, here 192.168.15.1.
Explorers > Routing > PSTN > PSTN Partner > (1) WAML18
NOTE: Activate Short Hold and set the Short Hold Time to 180 seconds.
A31003-H3160-S104-8-7620, 07/2014
Figure 12 WAML replacement - PSTN peer
PSTN Station Number

With this number the WAML reaches the survivability modem. The number is
configured on the S0 trunk with the extension 3277. Change Direction to
Incoming and Outgoing.
Explorers > Routing > PSTN > PSTN Peers > (1) WAML18 > Add Station
Number
A31003-H3160-S104-8-7620, 07/2014
Figure 13 WAML replacement - PSTN station number
You can check the result with Explorers > Routing > PSTN > PSTN Peers >
WAML18 > Display Station Number.
Static Route
Destination ist the signaling IP address of the HG 3575 (NCUI), as configured as
APIPADDR in AMO APRT (172.28.0.57)
The Route Gateway is the ISDN IP address of the modem (AMO SIPCO,
parameter SURVNET+AP no.): 192.168.15.18
The Destination Netmask (Ziel-Netzmaske) must be set to 255.255.255.255 for

tunneling. Therefore the netmask entry is hard coded to 255.255.255.255 and
read-only for STMI boards with WAML function.
Explorers > Routing > IP-Routing > Statische Routen > WAML18
Figure 14 WAML replacement - Static route
Save all the changes (disk icon) and reboot the board. Then the changes become
effective.
A31003-H3160-S104-8-7620, 07/2014
3.1.3.4 External ISDN Router as the Survivability Router
Figure 15 Signaling survivability without WAML replacement but with a router
By way of example, the settings for an external Cisco 1603R router are displayed.
IMPORTANT: The setting for this router is merely provided as an example and
is only intended to illustrate how to use the parameters in a router configuration.
The router selected in this case is not a special recommendation and its avail-
ability cannot be guaranteed. Routers from other product lines and manufacturers
can also be used.
A31003-H3160-S104-8-7620, 07/2014
Example Cisco 1603R APRT

hostname srt-isdn1 TYP=SURV
LSADDR
!
ip subnet-zero SIPCO
no ip finger TYP=LSNET
NETMASK
no ip domain-lookup
isdn switch-type basic-net3
file prompt quiet
!
interface Ethernet0
ip address 192.168.1.101 255.255.255.0
no ip directed-broadcast
APRT
! TYP=SURV
interface BRI0 ROUTERNR
ip address 192.168.15.1 255.255.255.0
no ip directed-broadcast SIPCO
encapsulation ppp TYP=LSNET
SURVNET
dialer map ip 192.168.15.43 name AP43 broadcast 00697654321
dialer-group 1 Phone number that must be
isdn switch-type basic-net3 dialed in order to access the
survivability modem
!
ip classless
ip route 192.168.22.43 255.255.255.255 192.168.15.43
ip route 192.168.23.98 255.255.255.255 192.168.15.98 LTU-Number of AP
ip route 192.168.200.18 255.255.255.255 192.168.15.18

!
APRT
dialer-list 1 protocol ip permit TYP=APNET
APIPADDR
A31003-H3160-S104-8-7620, 07/2014
Signaling Survivability via alternate LAN
3.2 Signaling Survivability via alternate LAN
3.2.1 Configuring the HiPath 4000
Figure 16 Signaling Survivability via alternate LAN
The configuration in the HiPath 4000 switch is realized as follows:
• If signaling survivability via alternate LAN will be used, UDP must be

configured for HSR signaling for the access point/HiPath 4000 SoftGate.
A31003-H3160-S104-8-7620, 07/2014
Access Point (direct link):

ADD-UCSU:UNIT=AP,LTG=1,LTU=17,LTPARTNO="Q2324-X10
",SRCGRP=1,FRMTYPE=AP37009,CONNTYPE=APDL,LSRTADDR=172.
15.3.17,APRTADDR=172.15.3.1,LOCID=722,LOCATION="722
",PHONE=722,PLCHECK=YES,BCHLCNT=120,CONVLAW=YES,TCLASS
=0,ALARMNO=0,IPMODE=IPV4,DHCPV4=NO,DHCPV6=NO,SIUANN=1,
SIUC=0,DTR=0,CNTRYCD=0,SIGMODE=HSRUDP;
HiPath 4000 SoftGate (networked link):

",SRCGRP=1,FRMTYPE=SOCOAP,CONNTYPE=APNW,LSRTADDR=172.1
5.3.1,APRTADDR=172.15.5.1,LOCID=722,LOCATION="SG39
",PHONE=722,PLCHECK=YES,BCHLCNT=250,CONVLAW=NO,TCLASS=
0,ALARMNO=0,SOCOTYPE=SOCO500,IPMODE=IPV4,DHCPV4=NO,DHC
PV6=NO,SIUANN=1,SIUC=0,DTR=0,CNTRYCD=0,SIGMODE=HSRUDP;
IMPORTANT: When switching from HSRTCP to HSRUDP or vice versa an

EXEC-USSU:TYPE=UPDATAP,LTU=<number>; must be executed.
Existing connections are cleared down without further warning!
• Announce the survivability routers in the system

Click Search, enter or change the router number and address on the Router
ADD-
APRT:TYPE=SURV,CONF=ROUTER,ROUTERNO=1,LSADDR=172.15.3.
202;
Router 1 from the example in Figure 16 “Signaling Survivability via alternate LAN”
is thus configured.
• Assign the access points to the survivability routers
Point
APRT:TYPE=SURV,CONF=AP,LTU=17,ROUTERNO=1,SURVTYPE=ALTL
AN,SURVIP=192.168.0.17,SURVNETM=255.255.255.0,ALTSRVRT
=192.168.0.1,VLANTAG=NO,VLANID=0;
ADD-
APRT:TYPE=SURV,CONF=AP,LTU=39,ROUTERNO=1,SURVTYPE=ALTL
AN,SURVIP=192.168.0.39,SURVNETM=255.255.255.0,ALTSRVRT
=192.168.0.1,VLANTAG=NO,VLANID=0;
A31003-H3160-S104-8-7620, 07/2014
3.2.2 Configuring the LAN Interface

Additionally to the configuration with the AMOs the LAN interface of the vHG 3575
in the HiPath 4000 SoftGate which is used for signaling survivability must be
assigned .
WBM > Configuration > Signaling Survivability Interface
Figure 17 Signaling Survivability LAN interfaces
3.2.3 Configuring the Router

Example for a router configuration
interface FastEthernet0/0
/*IP address and netmask of the survivability LAN
ip address 192.168.0.1 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
/*IP address and netmask of the HiPath 4000 LAN
ip address 172.15.3.202 255.255.255.0
duplex auto
speed auto
!
ip route 0.0.0.0 0.0.0.0 172.15.3.1
ip route 172.15.5.37 255.255.255.255 192.168.0.37
/*Routing for SoftGate 39
ip route 172.15.5.39 255.255.255.255 192.168.0.39
ip route 172.15.5.50 255.255.255.255 192.168.0.50
A31003-H3160-S104-8-7620, 07/2014
ip route 172.15.5.51 255.255.255.255 192.168.0.51

/*Routing for AP 17
ip route 192.168.10.17 255.255.255.255 192.168.0.17
ip route 192.168.10.19 255.255.255.255 192.168.0.19
3.2.4 Replacement of a defect NCUI Board with a new

NCUI Board
The golden load loadware of the NCUI board doesn’t support UDP functionality
which is necessary for signaling survivability via alternate LAN. Thus the following
steps have to be performed when replacing the board.
There are two possibilities:
Possibility 1:
1. Copy the latest NCUI loadware to the new board before going in service with
the board.
2. Perform the board replacement as usual (see also “Gateways HG 3500 and
HG 3575” > Section 4.2.2, “Exchanging Boards”).
Possibility 2:
1. Delete the assignment of the concerned access point/HiPath 4000 SoftGate
to the survivability routers.
DELTE-APRT:TYPE=SURF,KONF=AP,LTU=<number>;
2. Change signaling mode to HSRTCP.
CHANGE-UCSU:TYPE=AP,LTU=<number>,SIGMODE=HSRTCP;
3. In order for this change to become effective, the access point/HiPath 4000
SoftGate has to be restarted.
EXEC-USSU:TYPE=UPDATAP,LTU=<number>;
IMPORTANT: Existing connections are cleared down without further

warning!
4. Put the new NCUI board in service (see “Gateways HG 3500 and HG 3575”
> Section 4.2.2, “Exchanging Boards”).
5. Change back to HSRUDP as signaling mode (see Section 3.1.1, “Configuring

the HiPath 4000”).
6. Reconfigure the assignment of the survivability routers (see Section 3.1.1,

“Configuring the HiPath 4000”).
A31003-H3160-S104-8-7620, 07/2014
Is Signaling Survivability Currently Active? (DIS-UCSU)
3.3 Is Signaling Survivability Currently Active? (DIS-UCSU)

When a system is operating with signaling survivability, it is often necessary -
without analyzing any error messages - to query whether an access point is
currently being controlled normally via LAN or whether it is being controlled via
modem with signaling survivability.
This query is executed with the AMO UCSU.
The query with the AMO UCSU can only be executed in expert mode.
(see AMO command)
DISPLAY-UCSU:AP,1,;
The AMO returns an overview of all configured access points, containing not
just configured parameters, but also current operating states.
+---------+-------------------+---------+--------------+----------+--------+
|ADDRESS |EXPECTED CONFIGUR. |STATE |LTUC MODULE |LTU-TYPE |FRMTYPE |
| +-------------------+---------+--------------+----------+--------+
| |CONNTYPE LOCATIONID LOCATION SRCGRP |
| |PHONE: FAX: |
| |LSRTADDR APRTADDR BCHL BCHLCNT PLCHECK SIGNAL. |
| |IP MODE DHCP V4 DHCP V6 AP REDUNDANCY TO APXY STATUS |
| |CONVLAW CONTROL UNIT TCLASS ALARMNO |
| |CNTRYCD SIGMODE |
| +----------------------------------------------------------------+
| |SIGNAL. ENCRYPTION ACTIVE [ ] PAYLOAD ENCRYPTION ACTIVE [ ] |
| |SECURE STATE : SEE DESCRIPTION AT BOTTOM |
+---------+-------------------+---------+--------------+----------+--------+
|AP 1.17|ADDED |READY |Q2324-X10 |AP37009 |AP37009 |
| +-------------------+---------+--------------+----------+--------+
| |APDL 722 722 1 |
| |PHONE: 722 FAX: |
| |172.015.003.017 172.015.003.001 120 100 YES ALTLAN |
| | IPV4 NO NO AP REDUNDANCY TO AP |
| | YES HOST-CC 0 0 |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
| |CPTON / SIUTON : NO DIFFERENCE TO ZAND |
+---------+-------------------+---------+--------------+----------+--------+
|AP 1.18|ADDED |READY |Q2329-X |AP37009 |SOCOAP |
| +-------------------+---------+--------------+----------+--------+
|SOCOTYPE |APDL 722 722 1 |
|SOCO1000 |PHONE: 722 FAX: |
| |172.015.003.018 172.015.003.001 250 250 NO MODEM |
| | NO HOST-CC 0 0 |
| |K HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : D SIUC : 0K DTR : 0K |
A31003-H3160-S104-8-7620, 07/2014
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |172.015.003.019 172.015.003.001 250 250 YES LAN |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |APDL 722 722 1 |
| |172.015.003.026 172.015.003.001 60 60 NO LAN |
| |0 HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |APDL 722 722 1 |
| |172.015.003.027 172.015.003.001 60 60 YES LAN |
| |0 HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
|AP 1.36|ADDED |READY |Q2305-X35 |INCH19 |INCH19 |
| +-------------------+---------+--------------+----------+--------+
| |APNW 722 722 1 |
| |172.015.003.001 172.015.005.001 60 60 YES MODEM |
| |0 HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : D SIUC : 00 DTR : 00 |
A31003-H3160-S104-8-7620, 07/2014
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |APNW 722 722 1 |
| |172.015.003.001 172.015.005.001 60 60 NO LAN |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
|SOCOTYPE |APNW 722 SG38 1 |
| |172.015.003.001 172.015.005.001 250 250 YES MODEM |
| |0 HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |172.015.003.001 172.015.005.001 250 250 YES LAN |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |172.015.003.041 172.015.003.001 250 250 YES LAN |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
A31003-H3160-S104-8-7620, 07/2014
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
| +-------------------+---------+--------------+----------+--------+
| |172.015.003.001 172.015.005.001 250 250 YES ALTLAN |
| |0 HSRUDP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 1 SIUC : 00 DTR : 00 |
| +----------------------------------------------------------------+
+---------+-------------------+---------+--------------+----------+--------+
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs
4 Relevant AMOs

Language
APRT ROUTERNR d Nummer des Routers für Signaling Survivability.
IPDA unterstützt bis zu 10 Survivability Router,
welche von 1..10 durchnummeriert und über
diesen Index verwaltet werden.
ROUTERNO e Number of the Router for Signaling Survivability.
IPDA supports up to 10 survivability routers,
numbered 1..10 which are administered using this
index.
LSADR d IP-Adresse eines Routers für Signaling
Survivability im HiPath 4000 LAN Segment.
Segment gehören (siehe IP Distributed
Architecture > Parameter NETADR im AMO
SIPCO, Table 1 “AMO SIPCO parameters in ADD
branch or for CHANGE under TYPE=LSNET”)
LSADDR e IP Address of a Router for Signaling Survivability in
the HiPath 4000 LAN Segment.
LAN Segment (see IP Distributed Architecture >
parameter NETADDR in AMO SIPCO, Table 1
“AMO SIPCO parameters in ADD branch or for
CHANGE under TYPE=LSNET”)
Table 1 AMO APRT parameters in ADD branch under TYPE=SURV,

CONF=ROUTER

Language
APRT ROUTERNR d Nummer des Routers für Signaling Survivability.
Bestimmt einen der bis zu 10 Survivability Router,
über den dieser Access Point erreicht werden
soll.
ROUTERNR e Number of the Router for Signaling Survivability.
Selects one of the up to 10 survivability routers,
via which this Access Point shall be reached.
SURVTYP d MODEM = Signaling Survivability über Modem
ALTLAN = Signaling Survivability über
alternatives LAN
SURVTYPE e MODEM = Signaling survivability via Modem
ALTLAN = Signaling survivability via alternate
LAN
Table 2 AMO APRT parameters in ADD branch under TYPE=SURV,

CONF=AP
A31003-H3160-S104-8-7620, 07/2014
Relevant AMOs

Language
UCSU SIGMODE d HSRTCP: HSR über TCP-Verbindung
HSRUDP: HSR über UDP-Verbindung
SIGMODE e HSRTCP: HSR via TCP connection
HSRUDP: HSR via UDP connection
Table 3 AMO UCSU parameter in ADD/CHANGE branch under UNIT=AP
A31003-H3160-S104-8-7620, 07/2014
sip_conn_01_overview.fm
Overview
SIP Connectivity
SIP Connectivity
1 Overview
The "SIP Trunking" feature uses procedures described in the ECMA 355 standard
to connect HiPath 4000 systems, OpenScape systems, external servers (e.g.
OpenScape Xpressions) or SIP service providers via IP-based networks.
CorNet-NQ messages and CorNet-NQ features are signaled via native SIP (e.g
to SIP service providers via UDP or TCP) or tunneled over SIP-Q (e.g. to
OpenScape Voice (CorNet NQ via SIP over TCP)).
SRTP (Secure Real Time Protocol). Signaling is secured with TLS (Transport
Layer Security). See also "Signaling and Payload Encryption (SPE)".
1.1 Communication Matrix
1.1.1 SIP Subscriber
Partner terminal SIP subscriber

SIP subscriber ok
HFA subscriber ok
HiPath 3000/5000 H.323 ok (basic call only)
standard subscriber
HiPath 3000/4000 TDM ok
subscriber
PSTN subscriber ok (basic call only)
Table 1 SIP subscriber communication matrix
1.1.2 SIP Trunking
Partner system HiPath 4000 connection

HiPath 2000 Not impacted by SIP feature
HiPath 3000 From V8: Networking with CorNet-NQ (TDM), CorNet-
IP or SIP-Q V2
Table 2 Trunking communication matrix
A31003-H3160-S104-8-7620, 07/2014
Overview
SIP Interfaces
Partner system HiPath 4000 connection

HiPath 4000 V2.0: Networking with CorNet IP.
V3.0: Networking with SIP-Q V1.
From V4: Networking with SIP-Q V2.
OpenOffice EE From V1: The IP connection is implemented using SIP-
Q V2.
OpenScape Voice From V4 R1: The IP connection is implemented using
SIP-Q V2.
OpenScape Alarm Response From V3 R2: The IP connection is implemented using
SIP-Q.
SIP Service Provider Connection via native SIP trunk.
The SIP providers released in the HiPath 4000 can be
found in the Intranet on the page HiPath Ready
Certifications > Overview of all certifications > S >
"SIP Service Provider HiPath 4000.
Other Enterprise Products (e.g. If possible networking via CorNet-IP, otherwise via
OpenScape Xpressions) native SIP trunk.
Table 2 Trunking communication matrix
1.2 SIP Interfaces

The following SIP interfaces are a vailable for HiPath 4000:
• SIP subscriber
• SIP trunking
– SIP-Q trunking (e.g. for the connection to OpenScape Voice)
– native SIP trunking (e.g. for the connection to SIP service provider)
1.3 Supported RFCs (Request for Comments) for SIP Interfaces
RFC- Title Interfaces:

Number
Station Native Trunk SIP-Q
RFC 2198 RTP Payload for Redundant Yes Yes Yes
Audio Data
RFC 2246 The TLS Protocol Version No Yes Yes
1.0
RFC 2327 SDP: Session Description Yes Yes Yes
Protocol (obsoleted by
RFC4566)
Tabelle 3 Supported RFCs (Request for Comments) for SIP interfaces
A31003-H3160-S104-8-7620, 07/2014
Overview
Supported RFCs (Request for Comments) for SIP Interfaces

Number
RFC 2396 Uniform Resource Yes Yes Yes
Identifiers (URI): Generic
Syntax
RFC 2617 HTTP Authentication: Basic Yes Yes Yes
and Digest Access
Authentication
RFC 2782 DNS RR for specifying the No Yes Yes
location of services (DNS
SRV)
RFC 2833 RTP Payload for DTMF Yes Yes Yes
Digits, Telephony Tones and
Telephony Signals
RFC 2976 The SIP INFO Method No No Yes
RFC 3204 MIME media types for ISUP No No Yes
and QSIG Objects
RFC 3261 SIP: Session Initiation Yes Yes Yes
Protocol
RFC 3262 Provisional Response Yes Yes Yes
Acknowledgement
(PRACK) Early Media
RFC 3263 SIP Locating Servers No Yes Yes
RFC 3264 An Offer/Answer Model with Yes Yes Yes
SDP
RFC 3265 Session Initiation Protocol Yes No No
(SIP)-Specific Event
Notification
RFC 3310 HTTP Digest Authentication Yes Yes Yes
RFC 3311 Session Initiation Protocol Yes Yes Yes
(SIP) UPDATE Method
RFC 3323 A Privacy Mechanism for the Yes Yes No
Session Initiation Protocol
(SIP)
RFC 3324 Short Term Requirements Yes Yes Yes (but no
for Network Asserted use case)
Identity
RFC 3325 Private Extensions to the Yes Yes No
(SIP) for Asserted Identity
within Trusted Networks
RFC 3326 The Reason Header Field No No Yes
for the Session Initiation
Protocol (SIP)
A31003-H3160-S104-8-7620, 07/2014
Overview
Supported RFCs (Request for Comments) for SIP Interfaces

Number
RFC 3484 Default Address Selection No Yes Yes
for Internet Protocol version
6 (IPv6)
RFC 3515 The Session Initiation Yes Yes No
Protocol (SIP) Refer
Method1
RFC 3550 RTP: Transport Protocol for Yes Yes Yes
Real-Time Applications
RFC 3551 RTP Profile for Audio and Yes Yes Yes
Video Conferences with
Minimal Control
RFC 3581 An Extension to the Session No Yes No
Initiation Protocol (SIP) for
Symmetric Response
Routing
RFC 3711 The Secure Real-time No No Yes
Transport Protocol (SRTP)
RFC 3725 Best Current Practices for Yes No Yes
Third Party Call Control
(3pcc) in the Session
Initiation Protocol (SIP)
RFC 3830 MIKEY: Multimedia Internet No No Yes
KEYing
RFC 3842 Message Waiting Indication Yes Yes No
(partly)2 Event Package
Protocol (SIP) Replaces
Header
Protocol (SIP) Referred-By
Mechanism 3
RFC 4028 Session Timers in the Yes Yes Yes
(SIP)
RFC 4291 IP Version 6 Addressing No Yes Yes
Architecture
RFC 4568 Session Description No Yes Yes
Protocol (SDP) Security
Descriptions for Media
Streams
RFC 5746 Transport Layer Security No Yes Yes
(TLS) Renegotiation
Indication Extension
RFC 5806 Diversion Indication in SIP Yes Yes No
A31003-H3160-S104-8-7620, 07/2014
Overview
Boards Used

Number
RFC 5923 Connection Reuse in the Yes Yes Yes
(SIP)
RFC 5952 Registration for Multiple No Yes Yes
Phone Numbers in the
(SIP)4
RFC 6140 Transport Layer Security No Yes Yes
(TLS) Renegotiation
Indication Extension
1 Refer is only supported I/C for SIP subscribers and native SIP Trunks (configurable in WBM > SIP
Trunk Profiles) - (NOT RECOMMENDED FOR SIP Service Providers due to accounting, billing,
permissions etc.)
2 "partly"means that only the static subscription at Voice Mail Server ist supported (in outgoing
direction). HiPath 4000 doesn't support dynamic subscription in outgoing direction, i.e. no
SUBSCRIBE message is sent.
Static subscription is typical for PBXes (like HiPath 4000) and dynamic subscription is typical for
SIP clients.
In incoming direction (e.g. from a SIP client to HiPath 4000), both static and dynamic subscription
is supported.
3 Refer is only supported I/C for SIP subscribers and native SIP Trunks (configurable in WBM > SIP
Trunk Profiles) - (NOT RECOMMENDED FOR SIP Service Providers due to accounting, billing,
permissions etc.)
4 Only possible if SIP trunk profile is used.
1.4 Boards Used

The common gateway board HG 3500 and the virtual HG 3500 in HiPath 4000
SoftGate support SIP connectivity. For details, see "Gateways HG 3500 and HG
3575", Chapter 4, “Supported Gateways” and the documentation for "HiPath
4000 SoftGate".
A31003-H3160-S104-8-7620, 07/2014
Overview
Boards Used
A31003-H3160-S104-8-7620, 07/2014
sip_conn_02_subscriber.fm
SIP Subscriber
SIP Endpoints
2 SIP Subscriber
The feature "SIP Subscriber for HiPath 4000" encompasses the operation of SIP
endpoints, which can be run on a HiPath 4000 system using a gateway (virtual
HG 3500 or HG 3500).
Up to 240 native SIP subscribers can be configured on the common gateway HG

3500. The total number of 240 IP subscribers per common gateway (CGW) refers
to HFA and SIP subscribers (e.g. 200 HFA and 40 SIP subscribers).
Operation of SIP endpoints on an Access Point/HiPath 40000 SoftGate is also

supported.
2.1 SIP Endpoints

The following SIP endpoints are supported:
• OpenStage SIP familiy1
• LifeSize Phone (Audiokonferenz)
• OpenScape Personal Edition SIP
• Mediatrix Analog Access Points 41xx
• Mediatrix 44xx (nur HiPath 4000 SoftGate)
• OpenScape Xpert V4 (Trading IP)
• Video enpoints at HiPath 4000 SoftGate only (see „HiPath 4000 SoftGate“ >
Chapter 5, “Video Connections”)
In terms of subscriber support, the operation of HFA stations that run on an HG

3500 board is possible.
In both call directions, this feature encompasses
• G.7xx audio calls
– from SIP to SIP
– from SIP to HFA
– from SIP to TDM
• G.711 transparent FAX/MODEM calls
– from SIP to SIP
– from SIP to HFA
1. A project-specific release is required.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Service Information
– from SIP to TDM

• Up to 120 SIP endpoints can be configured on a HG 3500 board, these can
be spread across all available ports or configured on one port.
• RFC 2833 (DTMF via RTP) and RFC 2198 (Support of Redundant Audio
Data) are supported.
• The following table shows the combinations of the parameters SECZONE,

USERID and PASSWD in AMO SBCSU to make secure registration possible.
Parameter
SECZONE USERID PASSWD Possible
Set Set Set Yes
Not Set Set Set Yes
Set Not Set Set Yes
Not Set Not Set Set Yes
Set Not Set Not Set No
Not Set Set Not Set No
Set Set Not Set No
Not Set Not Set Not Set Yes
• Restriction for codec G.729.

The WBM interface allows you to configure all codecs from the G.729 family
(G.729, G.729A, G.729B and G729.AB). Only the highest priority codec is
used for SIP signaling.
• A high number of subscribers registering to the STMI board can cause

overload. In case of a high number of subscribers it is recommended to
configure a range for Min. Period of Registration (sec): and Max. Period of
Registration (sec): under Explorers >Voice Gateway > SIP Parameters.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
With this range a random timer will be taken from between this range for
further re-registrations after the initial SIP REGISTER message.
NOTE: It is recommended not to exceed 20 SIP Registration messages per

second.
2.3 Features
2.3.1 Overview
• CLIP/CLIR,
• COLP/COLR,
• Name display
If a name is configured with AMO PERSI, then it is displayed. If no name is
configured, then the display is empty (instead of NN).
• Call forwarding (no reply, busy, unconditional)
• Hold / Retrieve / Toggle
• Attended call transfer
• Semi attended call transfer
• Local 3-party conference (if supported from the SIP terminal)
• Message Waiting Indication (MWI) (for more information, please refer to

Section 2.3.4, “Message Waiting Indication (MWI)”)
• Do-not-disturb
• CSTA/ACL monitoring of SIP subscriber (for more information please refer

to Section 2.3.3, “CSTA/ACL Monitoring of SIP Subscribers”).
• Hunt group with SIP subscriber as slave
• T.38 fax connections with Mediatrix 41xx
• DTMF signaling (Inband and RFC2833 compliant)
• SIP session timer RFC4028 compliant (more information can be found in

Section 2.3.2, “SIP Session Timer”)
• Digest Authentication
• Number Identification
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
• Call waiting (take, reject or forward the call)
• Second call (forward the second call, hold)
• SIP Subscriber as Member/Master of an ONS Group
• SIP Subscriber as DSS Key on a Desktop Phone
• SIP Peer Filtering
• Supported RFCs (see Section 1.3, “Supported RFCs (Request for

Comments) for SIP Interfaces”).
• Programming of central call forwarding (CFU, CFNR, CFB)
• Number suppression
IMPORTANT: All other features that are offered by the SIP subscribers but
require board support do not work.
Passive Features
The following features cannot be activated by the SIP subscriber itself, but the
SIP subscriber can be integrated:
• Call park (A SIP subscriber cannot actively park another subscriber in the
system. However, the SIP subscriber can be parked by another subscriber.)
• Call back on busy/no reply (A callback can be entered on an SIP terminal if

free / busy, but the SIP terminal itself cannot enter a callback.)
• Pickup group (SIP subscriber can’t dial the code for call pickup but it can be
a passive memeber of the pickup group. That means, other subscribers of the
pickup group can pick up calls which destination number is the number of the
for the SIP subscriber).
2.3.2 SIP Session Timer

The "SIP Session Timer" provides a "keep alive" system for SIP sessions. If this
feature is activated, reINVITE or UPDATE messages are sent periodically during
an established connection. If the partner answers, the session is extended by a
period of time previously arranged between the partners. If the partner does not
answer, the session is released. This verifies whether the connection is still
established.
The marginal values for the duration of the extension can be set in the WBM of
the gateway:
WBM -> Explorer -> Voice Gateway -> SIP Parameters
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
Figure 1 SIP session timer
• The SIP session timer is activated by the Use RFC4028 checkbox.
• Session Expires: Determines the maximum time by which a session can be

extended.
• Minimal SE: Determines the minimum time by which a session can be

extended.
The actual duration of the extension also depends on the partner's settings but is
within the configured interval. A session is renewed as soon as half the duration
has expired.
IMPORTANT: Please note that very short intervals lead to increased message
traffic!
2.3.3 CSTA/ACL Monitoring of SIP Subscribers

The following ACL services are supported for the new feature ACL/CSTA
monitoring of SIP subscribers:
• Monitor Set
• Monitor Cancel
• Device Type Check
• Get Switching Function Devices
• Snapshot Call
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
• Snapshot Monitor
• Divert Call
• Continue Call
• Make Predictive Call
• Reject Call
SIP phones have a different behavior compared to HFA or digital phones (e.g.
OpenStage HFA/T). Because of the different behavior for SIP phones, ACL
monitoring will show in some call scenarios other monitoring flows compared to
ACL monitoring of digital extensions.
HiPath CAP V3.0 R9 (or higher) is needed for the corresponding CSTA services.
These are
• CSTA Monitor Start/Stop
• CSTA Snapshot Device/Call
• CSTA Get Device Type
• CSTA Get Switching Function Devices
The BLF WIN application R15.4.0 (busy lamp field) supports this new CSTA/ACL
monitoring feature and is able to display the device status in the busy lamp field
of the attendant consoles.
2.3.4 Message Waiting Indication (MWI)

The Message Waiting Indication MWI feature is activated/deactivated on each
SIP subscriber by setting the PMIDX parameter in AMO SBCSU and using
authorization MB in COS of the subscriber.
The feature is realized both for HiPath 4000 SoftGate and common gateway HG
3500.
MWI feature activation:

• Use AMO RICHT for MODE=PM to create a new IDX for phone mail access:
ADD-RICHT:MODE=PM,IDX=1,SAN=089-4711,NAME=XPRESSION;
MODE=PM Address mode of the route is Phone Mail (PM)

IDX Index of service access number
SAN Service access number
NAME Name of the route
• PMIDX=1 must be set for SIP subscribers in AMO SBCSU.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
• Set AVCE=MB (mail box (authorization to receive mail)) with AMO COSSU in
the subscriber COS.
MWI feature deactivation:

• PMIDX=0 must be set for SIP subscribers in AMO SBCSU.
• Set DVCE=MB to remove/deactivate authorization to receive mail in the

subscriber COS with AMO COSSU.
2.3.5 SIP Subscriber as Member/Master of an ONS

Group
Figure 2 SIP subscriber as a part of an ONS group
Use Cases
• A user who spends a lot of time outside of the office wants both phones (A)
and (B) to be ringing simultaneously - the fixed line at his desk and the SIP
device. The user has the choice of using the fixed line while in the office or, if
on the move, can use the SIP device.
• A typical scenario is also the use of One Number Service for service
deliveries. Depending on who is on duty, the responsible service technician is
reachable over one fixed number. If the responsible engineer needs to recall
the customer via the SIP device, the server number of the help desk is shown
in the customer's display. His own mobile phone number cannot be seen. This
ensures that the customer always reaches an employee when calling this
number.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
Requirements
• The ONS group must not contain any Anate, TDM or HFA (only use optiPoint
or OpenStage).
• The ONS group must not contain an external mobile phone.
• Parallel ringing must be initiated by the SIP phone (=MASTER).
Service Information
• ONS group features are limited. Only the currently supported SIP phone
features are supported.
• Activation of local features on the SIP phone is not signaled to the system and
therefore these features cannot be controlled by the system.
• Some system features are not released for SIP phones and some features
exist only for SIP phones. Therefore there are cases when ONS SIP groups
behave differently than ONS classic groups.
• COS MULTRA (multiple transactions - the station can be seized multiple

times) is a parameter which might be set for SIP devices, because it is
needed for some features to work correctly. When MULTRA is set, the busy
state of the SIP device is ignored by the system and a SIP phone is seized.
• Outgoing calls are always initiated with the number, COS and LCOS of the
master extension.
• MWI signaling (activation/deactivation) is sent to all devices in the ONS group
• Also the basic ONS principles apply for SIP ONS:
• While the call is ringing at the ONS group members the calling device
sees the ONS master extension number as the called number.
• Calls made by ONS members are initiated with the master number and
name.
• When one of the internal ONS group members answers, all other group
members are disconnected from the call.
• A call to any member of a group is signaled on all members as a group

call.
• Calls between members of the same ONS group are never signaled as
group calls.
• Feature Interaction
– Members display
ONS SIP members keep their own idle display, showing their number
rather than the master's number.
– Call Forward set with AMO ACTDA
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
Activation/Deactivation of Call Forwarding types using AMO ACTDA for

one SIP ONS member is propagated to all SIP ONS members.
Setting of Call Forwarding using AMO ZIEL is not possible for SIP
devices. Therefore it does not apply for SIP ONS groups.
Call Forward Busy set with AMO ACTDA is executed only if COS
MULTRA is not set.
– Local Call Forward

A SIP phone can activate internal Call Forward (SIP-specific feature). The
system is not informed of this action. Therefore call forward will be only
executed when the SIP phone is reached.
When a member has activated a local Call Forward, a call to the SIP ONS
group will ring for all members and then it will be forwarded to the call
forward destination.
Remarks:
– If both Call Forwards No Reply are set (local on the phone and with
AMO ACTDA) the one with the shorter no answer timer will be
executed.
– If master and slave have the same type of local Call Forward
activated, the master call forward will be executed.
– Deflect call
Deflect is a local feature that can be used by a SIP phone to transfer the
call in a ringing state. When one ONS SIP member invokes this feature,
the call will be transferred to the new destination.
– Refuse call
Refuse is a local feature that can be used by a SIP phone to reject a call.
When one ONS SIP member invokes this feature, the call will be
disconnected.
– Callback
Set Callback Free/Busy to SIP ONS group is possible and all members
are alerted after callback execution.
If a slave has COS MULTRA set and is busy then Callback Busy cannot
be set.
OBS: If Callback Busy is set when a slave is busy, it is not executed when
the slave goes idle. The master should go idle to invoke callback. This
behavior is inherited from the classic ONS group.
– Message Waiting Indication (MWI)

Message Waiting Indication is signaled to all SIP ONS members.
– Local Do not Disturb
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
If a member has DND (Do not Disturb) activated locally, all the other ONS
members are alerted shortly and then cleared when the member with
DND disconnects.
When DND is set for the ONS member, the behavior differs depending on
whether the member is a master or slave. If the member is a master, the
calling party gets the disconnect message in dialing state. If the member
is a slave, the calling party gets the disconnect message in ringback state,
because the master acknowledged the call just beforehand. In this
second case, the DND set for the slave is processed for the calling party
as a call reject.
Remark: DND for SIP cannot be set using AMO ACTDA.
– Local Call Log

Any call to the SIP ONS group will be saved in the alerted member's call
log.
– CHESE
CHESE is not released for SIP devices.
– Hunt group
A hunt group can be configured to have the ONS master as a member. If
the ONS master is a SIP phone, then the following hunt group and SIP
phone restriction applies: A functional device (or SIP device) configured
in a hunt group must never have the parameter MULTRA set in AMO
COSSU!
– Pickup group
Pickup group is not released for SIP devices.
– Out of Service
If the master SIP device is out of service any incoming call to the ONS
group is blocked.
If one of the slave SIP devices is out of service the other members work
as usual.
Remark: If the SIP phone is unplugged, it is not signaled as "Out of
Service" to the system.
– Second call
Call Waiting is a local SIP phone feature that can only be used if COS
MULTRA is set. The list below contains an overview of ONS group
behavior. Call Waiting for SIP phones is possible when the SIP phone is
in talk state. Call Waiting for SIP phones is not possible when the SIP
phone is in ringing state.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
ONS group action result when result when

state busy SIP has busy SIP has
CW on CW off
COS ONS is busy in call master call cleared, call cleared,
MULTRA set ring state busy busy
call slave call cleared, call cleared,
busy busy
ONS is busy, call master ONS ONS
master is in members ring members ring
talk state shortly and
then call
cleared, busy
call slave ONS ONS
members ring members ring
shortly and
then call
cleared, busy
ONS is busy, call master ONS ONS
slave is in talk members ring members ring
state shortly and
then call
cleared, busy
call slave ONS ONS
members ring members ring
shortly and
then call
cleared, busy
COS ONS is busy in call master call cleared, call cleared,
MULTRA not ring state busy busy
set
busy busy
ONS is busy, call master call cleared, call cleared,
master is in busy busy
talk state
busy busy
ONS is busy, call master call cleared, call cleared,
slave is in talk busy busy
state
busy busy
Remark: For the situation when COS MULTRA is set and busy SIP
phone has Call Waiting off:
– ONS is busy, master is in talk state: the call is disconnected before the
request is accepted.
– ONS is busy, slave is in talk state: the call is disconnected after

request is accepted.
– PIN and SIP phone display
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
ONS uses the Permanent PIN feature. In classic ONS implementation,

the pin of the master device is automatically activated on all slave devices
by starting up the phone or by configuring a new ONS group. PIN for SIP
phones is not implemented yet, therefore activation of master PIN is not
possible on SIP phone slaves. A SIP phone in an SIP ONS group will
present its own number on its display. The parameter DISPRSTN AMO
PERSI:COPIN does not apply for SIP ONS groups and the master
number will be always shown for internal SIP ONS calls.
– ACL
Call forwarding:
ACL reports call forwarding situations differently depending of call
forward activation (local or system), the COS MULTRA parameter and
which SIP ONS member is called.
Remark: Call Forward Unconditional/Busy activated locally on a slave
SIP phone is executed and reported as CF No Answer in ACL messages.
Incoming Calls:
ACL reports incoming calls differently to ONS scenarios depending on the
COS MULTRA and Local Call Waiting settings.
Restriction
• Handover will not be supported
• PIN is not supported for SIP devices; therefore the HiPath 4000 "PIN
permanent" feature isn't used.
Generation (example)
The master SIP phone must have PARARNGM set by AMO SDAT and the slave
SIP phone must have PARARNGS set by AMO SDAT.
SIP phone 3432 - Master of ONS group:

35,DVCFIG=S0PP,COS1=33,COS2=33,LCOSV1=5,LCOSV2=5,LCOSD1=5,LCOSD2
=5,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=0,PROT=SBDSS1,PERMACT=Y,INS=
Y,ALARMNO=0,OPTIDX=10,RCBKB=N,RCBKNA=N,CBKBMAX=5,HMUSIC=0,PMIDX=
1,IPCODEC=G7 11,PASSWD="",USERID="",SECZONE="";
CHANGE-SDAT:STNO=3433,TYPE=ATTRIBUT,AATTR=PARARNGM;
SIP phone 3433 - member of the ONS group:
CHANGE-SDAT:STNO=3433,TYPE=ATTRIBUT,AATTR=PARARNGS;
SIP phone 3434 - member of the ONS group:
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
CHANGE-SDAT:STNO=3434,TYPE=ATTRIBUT,AATTR=PARARNGS;
ONS group:
ADD-AUN:GRNO=1,TYPE=ONS,STNO=3432&3433&3434; /* SIP subscriber as

master and member of an ONS group
IMPORTANT: DIS-AUN for ONS presents the SIP member twice: once in the
member's area and once in the REMAC area.
2.3.6 SIP Subscriber as DSS Key on a Desktop Phone

Feature Description
It is possible to configure a SIP subscriber as a DSS key (DSS destination) on a
desktop phone with AMO ZIEL.
Scenarios
The busy condition of the SIP subscriber is displayed via a LED on the monitoring
extension's DSS key LED.
• LED off: SIP subscriber is free to get a call.
• LED on: SIP subscriber is busy.
If SIP subscriber is member of an ONS group
• If the SIP subscriber is the master of the ONS group, the DSS LED shows the
status of the ONS group.
• If the SIP subscriber is the slave and the slave number is monitored, the DSS
LED shows the status of the slave.
SIP subscriber is called if free (LED off) when the DSS key is pressed on
monitoring extensions.
Remarks
• The ringing state of the SIP subscriber is considered as busy, therefore the
DSS LED does not flash and call pickup is not possible.
• Local features activated on a SIP subscriber cannot be monitored by the

system. Call forwarding locally activated on the SIP subscriber will be
executed when the DSS key configured with the SIP subscriber as
destination is pressed.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Features
Digite: 3412, SIP: 3434
ADD-ZIEL:TYPE=DSS,SRCNO=3412,KYNO=12,DESTNOD=3434;
DIS-ZIEL:DSS,3412;
H500: AMO ZIEL STARTED
DSS
SOURCE | DEVICE | KEY | DEST. | SLKTYPE | SLKTEXT
-------------+--------+--------+--------------+----------+-------------
3412 | BD | 12 | 3434 | SLKSTNO |
AMO-ZIEL -111 DESTINATIONS FOR VARIOUS STATION FEATURES
DISPLAY COMPLETED;
2.3.7 SIP Peer Filtering

The feature SIP Peer Filtering is released with HiPath 4000 V6 R2 for HG 3500
and vHG 3500 SIP.
To avoid hacker attacks (scanning) via SIP trunks, only SIP requests from
"known" peers (partners) are answered, all other requests are ignored. "Known"
peers are IP addresses or FQDNs from activate trunk profile and eventually
registered SIP clients.
There are two operation modes:
• Gateway/HG configured (B channels) for SIP clients and SIP trunks.

Only incoming REGISTER messages from "known" peers will be answered,
all other requests from "unknown" peers will be ignored.
• Gateway/HG configured as trunking gateway only (there are only configured

SIP trunk B channels)
Only requests from "known" peers will be answered; all requests from
"unknown" peers will be ignored.
Typical use case where this feature should be activated is SIP trunk gateway
connected to SIP provider via WAN/internet without additional security tools like
firewall usage.
The feature can be activated in the SIP Trunk Profile Parameter menu via the
checkbox Enable SIP Peer Filtering. After activation/deactivation of the feature
the gateways be restarted.
WBM > Voice Gateway > SIP Trunk Profile Parameter
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Restrictions
Figure 3 SIP Peer Filtering
2.4 Restrictions
2.4.1 Restrictions of System Features

The following system features cannot be used by SIP terminals:
• Exec. / Secr. - SIP terminals cannot be configured as Chese members.
• Pickup group - SIP terminals cannot be members of a pickup group.
• Keyset functionality - SIP terminals cannot be configured as keysets.
• ACD (automatic callback (CCBS / CCNR))
• Emergency override / emergency release
• Directed call park
• Directed call pickup
• Witness Facility - An SIP terminal can only be the passive subscriber for the
witness facility.
• Malicious Call Identification/Tracing - A SIP terminal can be traced, but

cannot trace a connection itself.
• ACL/CSTA services, e.g. MakeCall
• SRTP is not supported for SIP stations.
• Recall after transfer ringing
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Restrictions
2.4.2 Restrictions of Terminal Features

The following entries must be deactivated on SIP terminals (either in the DLS
“Feature Availability” menu or on the terminal directly), as these features are not
supported by the HiPath 4000:
• Log forwarded calls
• Call display name
• Music on Hold
• Message waiting
• Auto. answer
• Auto. reconnect
• Park
• Call park pickup
• Blind transfer
• Callback - busy
• Callback - no reply
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
2.5 Configuration
Pen: 1-1-49 Security zone:

IP: 1.40.41.105 HIPATH4000.COM optiPoint IP
Subnet mask: 255.255.255.0
Default Gateway: 1.40.41.254
Station: 4420
Fix IP: 1.40.41.12

User-ID: USER 1
HG3500
Password: SECRET
LAN
optiPoint IP
HiPath 4000
Station: 4421
Fix IP: 1.40.41.13

optiPoint IP optiPoint IP User-ID: USER 2
Password: known
Station: 4422 Station: 4423
Fix IP: ------------- Fix IP: -------------

User-ID: USER 3 User-ID: -----------
Password: unknown Password: --------
DHCP-Server
2.5.1 STMI2/4 Board Configuration
Configuration Management --> System Data --> Board --> CGW Function
Block

Click New, enter data (header information, General Board Data tab, STMI2-IGW
Board Data tab, CGW Functionalities tab) and Save.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
ADD-BFDAT:FCTBLK=1,FUNCTION=SIP,BRDBCHL=BCHL60;
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=SIP,LINECNT=10,BCHLCN
T=10;
CHNAGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES;
ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=1,SLOT=49,PARTNO=”Q2316-X
“,FCTID=1,FCTBLK=1;
ADD-
CGWB:LTU=1,SLOT=49,SMODE=NORMAL,IPADR=1.40.41.105,NETMASK
=255.255.255.0,DEFRT=1.40.41.254;
The Parameter GWAUTREQ and SIPREG must be set to NO,in
situations where the board is used for SIP Subscriber.
CHANGE-CGWB:MTYPE=CGW,TYPE=SIPTRERH,GWAUTREQ=NO;
CHANGE-CGWB:MTYPE=CGW,TYPE=SIPTRSSA,SIPREG=NO;
2.5.2 Configuring a SIP Subscriber
IMPORTANT: Configuration of HG 3500 (CGW) board is prerequisite for SIP

subscriber support (see Section 2.5.1, “STMI2/4 Board Configuration”).
IMPORTANT: If the parameters SECZONE, USERID and PASSWD are used for
a secure registration in the AMO SBCSU, the parameter AUTHERF is set to YES
and the security data must be set also in the SIP terminal !
IMPORTANT: The parameter MBCHL in AMO SDAT should be set for all SIP
subscribers. If this parameter is not set, features which need a second b channel
are not possible (e.g. conference, second call).

Click New.
Enter Device Family and Device Combination: S0PP.
Enter Connection Type: SIPSEC.
Choose a PEN that has the Board Type: STMI2IGW.
Enter all COS* and LCRCOS* values on Basic 1 tab sheet.
Choose S0PP/S2PP Protocol on Bus Extension tab sheet.
Click Save.
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
0,DVCFIG=S0PP,COS1=1,COS2=1,LCOSV1=1,LCOSV2=1,LCOSD1=1,LC
OSD2=1,
PROT=”SBDSS1”,OPTIDX=10,IPADDR=1.40.41.12,PASSWD=”SECRET”
, USERID=”USER 1”,SECZONE=”HIPATH4000.COM”,FIXEDIP=YES,
AUTHREQ=YES,SMGSUB=NO;
CHANGE-SDAT:STNO=4420,TYPE=ATTRIBUT,AATTR=MBCHL;
2.5.3 Removing a SIP Subscriber

Click Search.
Select subscriber you want to delete.
Click Delete.
DELETE-SBCSU:STNO=4420,SVC=ALL;
2.5.4 Changing a SIP Subscriber

The SIP endpoint data is changed under branch “OPT=FPP”

Click Search.
Select subscriber you want to change. Change data.
Click Save.
CHA-SBCSU:STNO=4420,OPT=FPP,IPADDR=1.40.41.15,FIXEDIP=YES;
2.5.5 Enabling/Disabling DMC

DMC is enabled for station 4420 and disabled for station 4422 and 4423.

Click Search.
Select subscriber you want to change the DMC settings.
Acivate/deactivate check box DMC allowed on Basic 3 tab sheet.
CHANGE-SDAT:STNO=4420,TYPE=ATTRIBUT,AATTR=DMCALLWD;
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
2.5.6 Call Forwarding

3 kinds of call forwarding are possible:
• CFU - Call Forwarding Unconditional

ADD-ACTDA:TYPE=STN,STNO=<station
number>,FEATCD=FWD,CFVAR=<call forwarding
variant>,DTYPE=CFU,SI=VCE;
• CFNR - Call Forwarding No Reply
variant>,DTYPE=CFNR,SI=VCE;
• CFB - Call Forwarding Busy
variant>,DTYPE=CFB,SI=VCE;
2.5.7 Second Call

The attribute MBCHL (multiple b channels) must be set.
CHANGE-SDAT:STNO=<number of the sip
subscribers>,TYPE=ATTRIBUT,AATTR=MBCHL;
CHANGE-COSSU:TYPE=COS,COS=<COS number used for sip
subscribers>,AVCE=MULTRA;
IMPORTANT: COS MULTRA may not be used if stations are member of hunt
group!
2.5.8 Display of the SIP Subscribers

Registered and unregistered SIP subscribers can be displayed via the HG 35xx
Web Based Management in the HiPath 4000 Assistant.
In the HiPath 4000 Assistant:

Expert mode -> HG 35xx Web Based Management
In the HG35xx Web Based Management:

Explorer -> Voice Gateway
Registered subscriber
Explorer -> Voice Gateway - Clients - SIP
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
Client Registered: Yes
Unregistered subscriber
Explorer -> Voice Gateway - Clients - SIP

Client Registered: No
2.5.9 Signaling of SIP Subscriber Outage

Requirements:
SIP subscriber endpoints are used in several situations at the customer site.
Sometimes it is important to get informed, if a SIP endpoint gets out of service.
This can be done towards a SNMP-System that receives, interprets and displays
the content of SNMP-Traps.
Realization:
If SIP Phone goes out of service, SNMP Trap
"MSC_ERH_SUB_OUT_OF_SERVICE" from IGW (HG3540/50) to the LAN
network is reported. This SNMP trap includes information about time/date, IP
address and station number.
User interface:
The reported TRAP can be verified via WMB access to the HG 3500 board (HG
3540 function):
HiPath 4000 Assistant > Expert Mode > HG35xx WBM > Maintenance >
SNMP > Traps (MSC_ERH_SUB_OUT_OF_SERVICE)
2.5.10 Relevant AMOs

Language
ACTDA UART d CFB: Anrufumleitung bei besetzt
CFNR: Anrufumleitung bei nicht melden
CFU: ständige Anrufumleitung
DTYPE e CFB: call forwarding busy
CFNR: call forwarding no reply
CFU: Call forwarding unconditional
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration

Language
ART=HWYBDL d Highway-Bündel
TYPE=HWYBDL e Highway bundle
BKANSIP d Anzahl der B-Kanaele fuer die SIP-
Subscriber Funktion
BCHLSIP e Number of b channels for sip subscriber
function
FCTID d Function Id (wird immer auf 1 gesetzt)
FCTID e Function id (is always set to 1)
wählen)
FCTBLK e Function block index
LWVAR d Index auf Loadware Block der T1 Baugruppe
e Loadware variant
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
Q2316-X, Q2316-X10, Q2324-X500,
Q2324-X510
TYP=IPGW d IP Gateway (Common Gateway Baugruppe)
MTYPE=IPGW e IP Gateway (Common gateway board)
BFDAT ANZSATZ d Anzahl der funktionsbezogenen Saetze.
selected function.
BGBKAN d Block fuer Baugruppe mit 60 und/oder 120
B-Kanaelen
BRDBCHL e dedicates the block for boards with 60 and/or
120 b-channels
CONFIG=WEITER d Weitere Block-Konfiguration ermöglichen
CONFIG=CONT e Continue block configuration
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration

Language
FCTBLK e This index describes the function block
which should be configured on the common
gateway board. With that index the amount
of needed physical lines (board circuits) is
calculated.
Gateways fest. Dabei muss die eventuell
benötigte HG 3570 Funktion als erste
angeführt werden. Falls ein bestimmter Line-
Bereich für die Funktionen HG 3530 oder
HG 3550 vorreserviert werden soll, muss die
entsprechende Funktion am Ende stehen
und mit dem Wert HG35xxR abgeschlossen
sein. Die Funktion STANDBY kann nur als
Einzel-Funktion konfiguriert werden.
FUNCTION=SIP: SIP Subscriber Funktion
profile of the common gateway board. If
HG3570 functionality is used, it must be
functions HG3530 or HG3550 is desired, this
function must be at the end of the profile just
suffixed by the according HG35xxR value.
The function STANDBY can only be
FUNCTION=SIP:SIP subscriber function
CGWB DEFRT IP-Adresse des Default Routers innerhalb
des LAN-Segmentes.
Der Default Router übernimmt die
Weiterleitung der Pakete, die eine
Zieladresse außerhalb des eigenen LAN-
Segmentes haben.
0.0.0.0 bedeutet, daß kein Default Router
konfiguriert ist.
DEFRT e IP address of the default router within the
LAN segment.
The default router takes care of routing
forward all packets with a destination
address with a network part different from
the own LAN segment.
0.0.0.0 means that no default router is
configured.
IPADR e IP address of common gateway board
(source address)
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration

Language
MTYP=INITCGWB d Zurücksetzen der Konfigurationsdaten der
Common Gateway Baugruppe auf die
Standardwerte
MTYPE=INITCGW e Reset configuration data of common
B gateway board to default values
bezüglich des Netzanteils der IP-Adresse
gleich und bezüglich des Host-Teils
unterschiedlich sein (auch der Default
Router muss dieser Bedingung
entsprechen).
partition of an IP address. All IP addresses of
a LAN segment must contain the identical
SMODE=NORMAL d Standby Mode oder Normal Mode
Eine Baugruppe im Normal Mode hat gültige
Baugruppendaten und normalerweise auch
OPTIIPs konfiguriert.
Eine Baugruppe im Standby Ready Mode
hat keine gültigen Baugruppendaten, auf
diese Baugruppe können OPTIIPs
umgeschaltet werden, falls eine andere
Baugruppe aus demselben Baugruppen-
Pool (AMO BPOOL) defekt wurde.
Eine Baugruppe im Standby Defekt Mode
hat ebenfalls keine gültigen
aufgrund eines Defekts seine OPTIIPs und
seine Baugruppendaten abgegeben.
data and normally also OPTIIPs assigned to
it.
A board in Standby Ready Mode has no valid
board data, to this board OPTIIPs can be
switched over if another board of the same
board reconfiguration pool (AMO BPOOL)
becomes defective.
A board in Standby Defect Mode has also no
valid board data, this board has lost its
OPTIIPs and its board data to another board
because it's gone defective.
SBCSU ART=FPP d Hauptrufnummer des S0-/S2-Punkt zu Punkt
Anschlusses
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration

Language
OPT=FPP e Functional point-to-point connection
ANSCHL=SIP d Anschlussart=SIP
CONN=SIP e Kind of connection=SIP
GERKON=S0PP d S0-Punkt zu Punkt Anschluss
DVCFIG=S0PP e S0-point-to-point
PROT=SBDSS1 d Protokollvariante DSS1
PROT=SBDSS1 e Protocol variant DSS1
OPT=10 d Optiontabellenindex 10
OPTIDX=10 e Option table index 10
IPADR d IP-Adresse
IPADDR e IP address
PASSWD d Passwort
PASSWD e Password
KENNUNG d Benutzerkennung
USERID e User ID
SECBER d Security-Bereich (Art Domäne)
SECZONE e Security zone (kind of a Domain)
FESTEIP d Feste IP-Adresse
FIXEDIP e Fixed IP address
AUTHERF d Authentifizierung erforderlich
AUTHREQ e Authentification required
SMGTLN d SMG Teilnehmer;
Für Survivability-Lösung mit der H8k;
SMGSUB e SMG subscriber
For survivability solution with H8k;
SDAT EMERK d Teinehmermerkmal einfügen
AATTR e Add attribute
AMERK d Teinehmermerkmal ausfügen
DATTR e Delete attribute
A31003-H3160-S104-8-7620, 07/2014
SIP Subscriber
Configuration
A31003-H3160-S104-8-7620, 07/2014
sip_conn_03_trunking.fm
SIP Trunking
SIP-Q Trunking
3 SIP Trunking
3.1 SIP-Q Trunking

SIP-Q: CorNet-NQ tunneling over SIP. SIP-Q can be used to network HiPath
4000 and OpenScape Voice, for example.
3.1.1 Features
IMPORTANT: All CorNet-NQ- features can only be supported for networking

with SIP-Q.
3.1.1.1 Connectivity to OpenScape Voice
For connectivity with OpenScape Voice only the protocol SIP-Q V2 is supported.
SIP-Q V2 supports TLS (Transport Layer Security for signaling) and SRTP
(secure RTP for the payload).
SIP-Q is also used for the connectivity with HiPath OpenExchange providing a
very powerful and scalable IP LCR.
For SIP-Q connectivity towards OpenScape Voice the block-dial mode in HiPath
4000 LCR and for the subscribers must be configured. As of HiPath 4000 V5 two
block-dial modes are supported:
• like a SIP Phone in an OpenScape Voice solution.
• like the existing HiPath 4000 bock-dial mode (as known up to HiPath 4000
V4).
IMPORTANT: For the OpenStage 60 and 80 HFA the block dial mode has been
released with OpenStage HFA V2.
Features with SIP-Q V2 between HiPath 4000 and OpenScape Voice V3.1 R3
• Call identification
– CLIP/CLIR,
– COLP/COLR,
– CNIP/CNIR
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP-Q Trunking
– CNOP/CNOR
• Call transfer
• Call hold / retrieve / toggle
• Call Forwarding
– CFU (call forwarding unconditional)
– CFB (call forwarding on busy)
– CFNR (call forwarding no reply)
• Callback on busy subscriber / no reply
• Message Waiting Indication (MWI)
• Release links (also called route optimization or path replacement)
• Transmission of "CorNet-NQ" messages
• IPv6 (see "HiPath 4000 SoftGate" > Chapter 11, “IPv6”)
• Signaling (TLS) and payload encryption (SRTP) (see "Signaling and Payload
Encryption (SPE)")
Features with SIP-Q V2 between HiPath 4000 V6 and OpenScape Voice V4/
V5
All feature mentioned in the section above (Features with SIP-Q V2 between
HiPath 4000 and OpenScape Voice V3.1 R3) are also supported for a connection
between HiPath 4000 V6 and OpenScape Voice V4/V5.
Additionally, the following features are supported:
• Call data recording
• T.38 fax connections (e.g. for SIP-Q trunking in common gateway HG 3500
towards OpenScape Voice V4/V5)
3.1.1.2 HiPath Networks
SIP-Q V2 between HiPath 4000 and HiPath 3000 also tunnels the Cornet NQ
protocol like the H.323 based Cornet IP version and enables the rich ComScendo
feature set.
SIP-Q V2 is the preferred IP Trunking protocol for HiPath 4000 networks and
networking with HiPath 3000.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP-Q Trunking
3.1.1.3 Codecs per Destination Gateway for SIP-Q Trunking
Feature Description
HiPath 4000 can be configured such that a codec is chosen depending on the
destination gateway. This means that the voice codec settings are dependant on
the IP address of the destination gateway. Any other configuration options (e.g.:
fax settings) are not considered for this feature.
In order to specify the direction of the call, the following options can be used:
• Configure single IP addresses
• Configure a range of IP addresses
• Configure a subnet mask
Service Information
• This feature is supported for common gateway HG 3500 and vHG 35000
• This feature is only supported for HiPath 4000 internal SIP-Q networking that
uses fixed IP addresses.
• If FQDNs are used (e.g.: towards OpenScape Voice) then this feature cannot
be used.
• The specific voice codec settings should be evaluated for incoming and
outgoing calls (from a gateway perspective). The destination specific codecs
can be changed dynamically without any reboot (both for SIP-Q in common
gateway and HiPath 4000 SoftGate).
3.1.1.4 SIP Peer Filtering
SIP Peer Filtering is released with HiPath 4000 V6 R2 for HG 3500 and vHG
3500 SIP.
For more information please refer to Section 2.3.7, “SIP Peer Filtering”.
3.1.2 Restrictions
• Outband signaling is not supported.
The function must be deactivated via WBM:
WBM > Explorer > Payload > HW Modules
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP-Q Trunking
• Trunking between HiPath 3000 and HiPath 4000

SIP registration of the HG 1500 board at the Large Enterprise Gatekeeper
(LEGK) is not supported.
• SIP-Q V2 connectivity between HiPath 4000 V4/V5 and OpenScape Voice

V3.1 R3
Call detail recording is not supported.
3.1.3 Configuration
see Chapter 5, “Configuration of SIP-Q-Trunking / Native SIP Trunking”.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
Native SIP Trunking
3.2 Native SIP Trunking

Native SIP trunks can be used to connect to any external system, SIP service
provider (see Section 3.2.3.1, “SIP Service Provider”) or 3rd party SIP products
(e.g. OpenScape Xpressions, Section 3.2.3.3, “Applications”).
3.2.1 Features
IMPORTANT: The availability of the following functionalities depends on the

other SIP partner and must be tested individually!
• Basic Call in accordance with RFC3261 SIP (for supported RFCs please refer
to Section 1.3, “Supported RFCs (Request for Comments) for SIP Interfaces”)
• CLIP/CLIR,
• COLP/COLR,
• Sending and receiving E.164 telephone numbers (e.g. +498972237729)
• Name display (e.g. for OpenScape Xpressions V6 connectivity)
• Call hold / retrieve / toggle
• Call transfer (attended call transfer / semi-attended call transfer / blind call
transfer)
• Call forwarding ("forward switching" method)
IMPORTANT: Call forwarding via "Call rerouting method" is not supported.

Instead diversion header is supported (sending of call forwarding information;
required for call forwarding scenarios to SIP service provider).
• Conferencing (3 party conference)
• Message Waiting Indication MWI

This feature can be used for SIP connectivity towards service providers
offering hosted Unified Messaging services.
• DNS SRV - Locating and addressing SIP servers/proxies using fully qualified
domain names
• SIP proxy failover and recovery
• Registration to SIP service provider (registration to the HiPath 4000 from

other vendors is not supported).
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
Native SIP Trunking
• Session border controller connectivity
• SIP session timer RFC4028 (more information can be found in Section 2.3.2,
“SIP Session Timer”)
• Digest authentication
• L2 and L3 QoS for signaling and payload
• T.38 fax connections (towards SIP service providers, e.g. T-Systems)
• DTMF signaling (Inband and RFC2833 compliant)
• Voice codecs G.729 and G.711
• Silence suppression
• Inband / outband proxy configuration
• Flexible native SIP trunking profiles (enable easy SIP service provider
integrations and administration)
• UDP and TCP transport for native SIP trunking
• IPv6 (see "HiPath 4000 SoftGate" > Chapter 11, “IPv6”)
• Signaling (TLS) and payload encryption (SRTP) (see "Signaling and Payload
Encryption (SPE)")
Additional features are not supported. HiPath systems are normally networked
via SIP-Q (see Section 3.1, “SIP-Q Trunking”).
3.2.2 Restrictions
• Common Gateway HG 3500: SRTP is not supported for native SIP trunking.
• Outband signaling is not supported.

The function must be deactivated via WBM:
WBM > Explorer > Payload > HW Modules
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
Native SIP Trunking
• Trunking between HiPath 3000 and HiPath 4000

SIP registration of the HG 1500 board at the Large Enterprise Gatekeeper
(LEGK) is not supported.
3.2.3 Use Cases
3.2.3.1 SIP Service Provider
Native SIP trunking is mainly used for connections to SIP service providers.
IMPORTANT: For a connection to a non-released SIP service provider a change

request has to be written!
The SIP providers and SIP trunking partners released in the HiPath 4000 can be
found on the Intranet page Index H > HiPathReady Zertifizierungen >
Übersicht aller Zertifizierungen > S > "SIP Service Provider HiPath 4000"
(Certifications - Overview of all Certifications) and are also listed in the HiPath
4000 Release Notes. They will be updated with every new minor or fix release.
For more information please refer to Chapter 4, “SIP Service Provider / SIP
Carrier”.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
Native SIP Trunking
3.2.3.2 Remote Agent Server Connectivity
IMPORTANT: This feature is relased for HiPath 4000 V6 R2 and higher.
Remote agent server enables remote connectivity of agents via mobile phones or
home phones or any phone with DTMF. As of HiPath 4000 V6 R2 this connectivity
is estabilshed via a native SIP trunk interface.
This feature can be activated with the WBM:
Explorers > Basic Settings > (right-click) Gateway > Edit Gateway Properties
> check Enable HFA via SIP
Figure 4 Remote Agent Server connectivity via SIP trunking interface
For more information please refer to the Remote Agent Server Solution
documentation.
3.2.3.3 Applications
Native SIP trunking is also used however for connectivity with other proprietary
applications, such as OpenScape Xpressions.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
Native SIP Trunking
3.2.4 Configuration
3.2.4.1 General Configuration
see Chapter 5, “Configuration of SIP-Q-Trunking / Native SIP Trunking” or

Chapter 4, “SIP Service Provider / SIP Carrier”.
3.2.4.2 Codec Configuration
OpenScape Xpressions supports the following codecs:
• G711-A,
• G711-µ
• G729AB.
Codec configuration is performed via CHANGE-CGWB or via WBM:

CHANGE-
CGWB:MTYPE=CGW,LTU=<LTU>,SLOT=<SLOT>,TYPE=ASC,PRIO=PRIO1,CODE
C=<CODEC>,RTP=<RTP>;
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
3.3 SIP Trunk Profiles

From HiPath 4000 V6 or later you must configure native SIP trunking
connections (e.g. to a SIP service provider) via the WBM with SIP trunk profiles.
There are already various standard SIP trunk profiles available in the WBM for
this purpose.
From HiPath 4000 V6, it is also possible to configure SIP-Q trunking connections
(e.g. to OpenScape Voice) via the WBM with SIP trunk profiles. There are also
various standard SIP-Q trunk profiles available in the WBM for this purpose.
Information about already available SIP trunk profiles you can find in Section
3.3.4, “Default Profiles”.
3.3.1 Advantages
These are the advantages of using SIP trunk profiles:
• More security
If (standard) Proxy, Inbound proxy and/or Outbound proxy were
configured via the WBM, with each incoming call a check is carried out as to
whether this originates from a valid IP address. If it is not, the call is rejected.
• DNS SRV support

DNS SRV can be used to propagate via DNS which IP-based services (e.g.
SIP) in a domain (e.g. SIP provider domain) are provided.
• SIP specifics support for trunk partners

The trunk profile parameters describe the SIP specifics (e.g. SIP header) of
trunk partners (e.g. SIP provider).
3.3.2 Disadvantages
If SIP trunk profiles are used, only one trunking partner can be addressed per
board.
3.3.3 Notes
• Only one profile can be activated.
• The outbound proxy must be configured if a Session Border Controller (SBC)

is used for LAN/WAN Nat-Traversal.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
3.3.4 Default Profiles

Standard SIP trunk profiles for native SIP and SIP-Q trunking scenarios are
already available and assigned default values:
For example:
• Native SIP Trunking
– Arcor
– Broadsoft
– OpenScapeUC
– NatTrkWithoutRegistration (native SIP trunking without registration)
– NatTrkWithoutRegistration (native SIP trunking with registration)
– NATTrkEnterprise
• SIP-Q Trunking
– SIPQTrkWithoutRegistration (SIPQ trunking without registration)
– SIPQTrkWithoutRegistration (SIPQ trunking with registration)
The default profiles contain specific provider profiles which have been tested and
released. The list of the default profiles can be extended with later minor releases
/ hotfixes.
3.3.5 Activating the SIP Trunk Profiles
3.3.5.1 Native SIP Trunk Profiles
1. Make sure that the SIP protocol variant for IP networking is set to native SIP
in AMO CGWB (parameter TRPRSIP).
2. By default, the SIP trunk profiles for native SIP are activated in the WBM. If
this feature was deactivated, it must be activated in the respective board /
HiPath 4000 SoftGate in the WBM.
Call up:
WBM > Explorer > Voice Gateway > SIP Trunk Profile Parameter > (right-
click) Activate checkbox "Use Profiles for Trunks via Native SIP"
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 5 Activating SIP trunk profiles
The menu SIP Trunk Profiles is then visible in the WBM under voice gateway
(see Section 3.3.6, “"SIP Trunk Profiles" menu”)..
3.3.5.2 SIP-Q Trunk Profiles
1. Make sure that the SIP protocol variant for IP networking is set to SIP-Q in
AMO CGWB (parameter TRPRSIPQ).
2. By default, the SIP trunk profiles for SIP-Q are deactivated in the WBM. To
use this feature, it must be activated in the respective board / HiPath 4000
SoftGate in the WBM.
Call up:
WBM > Explorer > Voice Gateway > SIP Trunk Profile Parameter > (right-
click) Activate checkbox "Use Profiles for Trunks via SIP-Q"
The menu SIP Trunk Profiles is then visible in the WBM under voice gateway
(see Section 3.3.6, “"SIP Trunk Profiles" menu”)..
3.3.6 "SIP Trunk Profiles" menu
IMPORTANT: In the SIP Trunk Profile Parameter menu, the Use Profiles
checkbox must be activated. Otherwise the SIP Trunk Profiles menu is not
displayed (see Section 3.3.5, “Activating the SIP Trunk Profiles”).
Call up:
WBM > Explorer > Voice Gateway > SIP Trunk Profiles
Numerous SIP trunk profiles for native SIP trunking scenarios are already
provided with default values (see Section 3.3.4, “Default Profiles”).
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 6 Example of a standard profile:
3.3.6.1 Change
The following connection parameters can be modified.
• Account/authentication required (see Section 3.3.6.2, “Authentication”)
• Remote Domain Name
• SIP Transport Protocol
• Registrar, IP address/host name and/or port
• Proxy
• Outbound proxy
• Inbound proxy
• Security (see Section 3.3.6.3, “Security”)
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
The features available in the sections CLIP/CLIR, Call number formatting and
Miscellaneous cannot be changed. If anything needs to be adapted here, a new
profile must be created.
The port values (Registrar, Proxy, Inbound Proxy, Outbound Proxy Port) are set
by default to 0. If DNS names (and not IP addresses) are configured for Registrar,
Proxy, Inbound Proxy or Outbound Proxy in the SIP trunk profile, DNS SRV is
used for resolution.
3.3.6.2 Authentication
If the partner requires the "Authentication" feature to be active, this must be

configured for the corresponding profile. The corresponding data (login and
password) is specified by the trunking partner. Additionally the trunking
connection with registration must then naturally work.
IMPORTANT: Authentication must be performed prior to activating the SIP trunk

profile.
Procedure:
1. In the SIP trunk profile menu activate the Account/Authentication required

checkbox.
2. Right-click Add Account/Authentication from the menu and enter the data
provided by the trunking partner.
Figure 7 Add Account/Authentication (Example)
3. Activate the profile (see Section 3.3.6.4, “Activate”).
3.3.6.3 Security
The security parameters are different for native SIP trunk profiles and SIP-Q trunk
profiles.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
RTP security mode for SIP-Q trunk profiles

RTP security mode can be configured for SIP-Q trunk profiles. If all conditions for
SRTP are fulfilled, the payload is encrypted in accordance with the configuration.
Figure 8 Security configuration for SIP-Q trunk profiles
Security mode for native SIP trunking

The security mode can be configured for native SIP trunk profiles. The
configuration options offered depend on which modes are released for this SIP
trunk partner and which gateway is configured.
The common gateway board does not support payload security on the native SIP
trunk. If all conditions for the defined security mode are fulfilled, signaling and/or
payload will be encrypted if necessary. The payload is encrypted with the RTP
security mode that was defined when the mode was released.
The RTP security mode "SDES with fallback to insecure" was defined for the
native SIP trunk profiles "NatTrkEnterprise", "NatTrkWithoutRegistration" and
"NatTrkWithRegistration".
If no security is released, then only No Security will be offered. If only signaling

security is released or if the common gateway is used, only the two options "No
Security" and "Only Signaling Security" will be available for selection.
Figure 9 Security configuration for SIP-Q trunk profiles
3.3.6.4 Activate
Once the profile has been configured, it must then be activated.
Procedure:
1. Mark a SIP trunk profile.
2. Select Activate from the menu (right-click).
If the profile was activated successfully, the entire profile turns green.
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 10 Activated SIP trunk profile (Example)
IMPORTANT: If "Account/Authentication required" is activated in the configured

profile, an account with authentication data has to be added before the profile is
activated (see Section 3.3.6.2, “Authentication”).
3.3.6.5 Deactivate
Procedure:
2. Select (right-click) Deactivate from the menu.
Once the profile is successfully deactivated, the green coloring is removed.
3.3.6.6 Delete
Before a SIP trunk profile can be deleted, all accounts must first be deleted. Only
then can the SIP trunk profile be deleted.
Procedure:
2. Select (right-click) Delete from the menu.
The selected profile is deleted.
3.3.7 Configuration of SIP Trunks with/without

Registration
Make sure that the prerequisites for using the menu “SIP Trunk Profiles” are met
(see Section 3.3.5, “Activating the SIP Trunk Profiles”).
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
3.3.7.1 Native SIP Trunks
Configuration with Registration
1. Change the profile

The "NatTrkWithRegistration" profile offered can be used for trunk
configurations with registration. The account name and authentication data
can be configured.
Explorer > Voice Gateway > SIP Trunk Profile > NatTrkWithRegistration
> (right mouse click) Modify > Activate checkbox Add Account/
Authentication
Figure 11 Account/authentication data
2. Configure the IP address/host name and domain name

The trunk partner IP address/host name (e.g. DNS name = provider.com)
must be configured in the Registrar section and in the Proxy section. The
remote domain name normally has the same value as the IP address/host
name (see Sections Registrar or Proxy) and is used as a host part in the
URL of the SIP messages.
> (right mouse click) Modify
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 12 SIP trunk profile of a provider with registration
3. Activate the profile

The profile must now still be activated. If the profile was activated
successfully, the profile will be colored green.
> (right mouse click) Activate
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 13 Activated SIP trunk profile (with registration)
Configuration without Registration
1. Configure the IP address

The NatTrkWithoutRegistration profile offered can be used for trunk
configurations without registration. The provider IP address/host name (e.g.
IP=1.2.3.4) must be configured in the proxy section.
Explorer > Voice Gateway > SIP Trunk Profile >
NatTrkWithoutRegistration > (right mouse click) Modify
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 14 SIP trunk profile of a provider without registration

NatTrkWithoutRegistration > (right mouse click) Activate
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 15 Activated SIP trunk profile (without registration)
3.3.7.2 SIP-Q Trunks
Configuration with Registration
1. Change the profile

The "SIPQTrkWithRegistration" profile offered can be used for trunk
configurations with registration. The account name and authentication data (if
required) can be configured.
SIPQTrkWithRegistration > (right mouse click) Modify > Activate checkbox
Add Account/Au-thentication
2. Configure the IP address/host name and domain name
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
The trunk partner IP address/host name (e.g. DNS name = provider.com)

must be configured in the Registrar section and in the Proxy section. The
domain name normally has the same value as the IP address/host name
(see Sections Registrar or Proxy) and is used as a host part in the URI of
the SIP messages.
SIPQTrkWithRegistration > (right mouse click) Modify
Figure 16 SIP-Q trunk profile with registration

SIPQTrkWithRegistration > (right mouse click) Activate
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 17 Activated SIP-Q trunk profile with registration
Configuration without Registration
1. Configure the IP address

The SIPQTrkWithoutRegistration profile offered can be used for trunk
configurations without registration (e.g. networking with OpenScape Voice).
The IP address/host name (e.g. IP=1.2.3.4) must be configured in the proxy
section.
SIPQTrkWithoutRegistration > (right mouse click) Modify
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 18 SIP-Q trunk profile without registration

SIPQTrkWithoutRegistration > (right mouse click) Activate
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
Figure 19 Activated SIP-Q trunk profile without registration
A31003-H3160-S104-8-7620, 07/2014
SIP Trunking
SIP Trunk Profiles
A31003-H3160-S104-8-7620, 07/2014
sip_conn_04_sip_provider.fm
SIP Service Provider / SIP Carrier
Motivation
4 SIP Service Provider / SIP Carrier
IMPORTANT: A list with certified SIP providers can be found in G-DMS

document INF-13-000534.
4.1 Motivation
With the increasing availability of high-performance DSL connections, the
number of VoIP users in the SOHO (Small Office / Home Office) area is constantly
growing. In contrast, external voice communication from a company or company
network is currently exclusively via ISDN connections to the carrier and service
provider networks.
Almost all carriers now offer a direct, IP-based network interface, on which
Session Initiation Protocol (SIP) is implemented as the connection and
communication protocol between the IP-PBX and SIP carrier connection. IP-
based network interfaces can be used instead of or in addition to the existing
ISDN system connections.
The following figure shows an example of this type of network interface:
Figure 20 SIPconnect reference architecture
Native SIP enables IP-based, direct connection or network interface between a

HiPath 4000 system and an SIP carrier. The connection can be also be used
without forced migration of internal company communication to VoIP. In a HiPath
4000 system, the SIP carrier connection can, of course, be configured in addition
to the traditional ISDN connections.
A31003-H3160-S104-8-7620, 07/2014
HiPath 4000 Special Features
4.2 HiPath 4000 Special Features

HiPath 4000 supports SIP profiles for configuring the service provider carrier.
Using the SIP trunk profile has the following advantages:
• More security
If the (default) proxy, inbound and/or outbound proxy have been configured
via WBM, the system checks whether each incoming call is coming from a
valid IP address. If it is not, the call is rejected.
• DNS SRV support

You can use DNS SRV to propagate via DNS which IP-based services (e.g.
SIP) are offered in a domain (e.g. SIP provider domain).
• SIP specifics support for trunk partners

The trunk profile parameters describe the SIP specifics (e.g. SIP header) of
trunk partners (e.g. SIP provider).
4.3 Configuration Basics
4.3.1 Configuration
The feature is configured in two or three steps, depending on the initial situation.
• Without Session Border Controller

If no session border controller is present, the feature is configured via AMOs
and via WBM. In this case, the (v)HG 3500 receives an IP address from the
WAN. This IP address is permanently allocated by the service provider.
• With Session Border Controller

If a session border controller is being used, it must also be configured. In this
case, the (v)HG 3500 has an IP address in the customer LAN, while the
session border controller has two IP addresses - one from the customer LAN,
and the other from the service provider WAN. The session border controller
operates as a router for the (v)HG 3500 in the WAN.
• DNS
As you are using Internet telephony and the Internet operates based on
names, it is always advisable to use DNS.
4.3.2 Notes
A31003-H3160-S104-8-7620, 07/2014
Scenario 1: Gateway direct to SIP Carrier
In the following example, a HG 3500 is used as an SIP trunking gateway. You

could also use a virtual HG 3500 in a HiPath 4000 SoftGate as an SIP
trunking gateway. To do this, the AMO batch must be adapted to reflect the
part number (AMO BCSU) and device type (AMO TDCSU).
• Features of SIP carriers

This application scenario shows the connection to the SIP carrier. The service
technician will use a standardized test plan with the support of system
development to determine which features are possible using the respective
SIP carrier.
4.4 Scenario 1: Gateway direct to SIP Carrier
4.4.1 Initial Situation

Key parameters:
SIP registrar / proxy sip.iandc.training.com 2.3.3.124

DNS - service provider iandc.training.com (domain name) 2.3.3.123
STNO carrier connection / HG 3500-1 +49180130100 3.3.3.11
STNO carrier connection / HG 3500-2 +49180130200 3.3.3.22
Figure 21 HG 3500 direct to SIP carrier
Subsequently, the following case should be configured. The HG 3500 of HiPath

4000-1 should be set up as a native SIP gateway and register at the service
provider. Registration should be performed using the phone number of the SIP
system connection (+49180130100).
A31003-H3160-S104-8-7620, 07/2014
Another HiPath 4000-2 from another customer has registered on the service
provider. This system has the system number +49180130200 and a four-digit
extension range. This system should be the dialing destination for the HiPath
4000-1 node in this scenario. Thus only one specific phone number is routed via
the SIP carrier connection instead of all phone numbers.
This section only explains configuration in the HiPath 4000-1 system.

Configuration of the HiPath 4000-2 system is almost identical, so this is not
described.
4.4.2 AMO Configuration

In AMO BFDAT a function block must be preset fro HG 3550:
ADD-BFDAT:FCTBLK=3,FUNCTION=HG3550,BRDBCHL=BCHAN60&BCHAN120;
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=3,FUNCTION=HG3550,LINECNT=2,UNITS=3;
HG 3530 is configured with function ID 1 and the functional block 3 described
above:
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=10,PARTNO="Q2324-
X500",FCTID=1,LWVAR="1",FCTBLK=0,BCHAN3550=60,ALARMNO=0;
The HG 3550 IP address is entered in the AMO CGWB. In this case, it is an
address from the WAN allocated by the service provider. The DNS whose
address is also entered here as DNSIPADR, is also in the service provider area:
ADD-CGWB:LTU=1,EBT=10,SMODE=NORMAL,IPADR=3.3.3.11,
NETMASK=255.255.255.0,BITRATE="AUTONEG",TRPRSIP=60,DNSIPADR=2.3.
3.123;
In the AMO CGWB, LEGKDATA section, the number of gateways is entered
(GWNO):
CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=10,TYPE=LEGKDATA,GWNO=1,REGEXTGK=NO;
In the AMO CGWB, external registration and digest authentication remain
deactivated:
CHA-CGWB:MTYPE=CGW,LTU=1,SLOT=10,TYPE=SIPTRERH,GWAUTREQ=NO;
CHANGE-CGWB:MTYP=CGW,LTU=1,SLOT=10,TYPE=SIPTRSSA,SIPREQ=NO;
You can configure a bundle for the SIP carrier application:
ADD-BUEND:TGRP:=55,NAME="SIP CARRIER",NO=60;
The following COT/COP classes are recommended:
ADD-COT:COTNO=55,COTPAR=ANS&CEBC&BSHT&BLOC&LWNC&NLCR&TSCS&
VNNO&NLCD&LINC&NOFT&NTON;
ADD-COP:COPNO=55,COPPAR=IMEX,TOLL=FBKW,TRK=FBKW;
A31003-H3160-S104-8-7620, 07/2014
You can then configure the AMO TDCSU. THe ISDNIP and ISDNNP parameters
are linked to the IMEX parameter. This allows an implicit number to be changed
into an explicit number. In this case, it is configured that an incoming number in
the format "Unknown" is transformed to an ISDN INTERNATIONAL phone
number if it begins with two zeros (ISDNIP=00). If the incoming number only
begins with one zero, it is changed into an ISDN National (ISDNNP=0):
ADD-TDCSU:ART=NEW,PEN=1-01-010-0,COTNO=55,COPNO=55,DPLN=0,VBZ=0,
COS=1,LCOSV=1,LCOSD=1,CCT="SIP CARRIER ",
DESTNO=0,PROTVAR="ECMAV2",SEGMENT=8,ATNTYP=CO,ISDNIP=00,ISDNNP=0
,TRACOUNT=31,SATCOUNT=MANY,NNO=1-40-155,ALARMNR=2,FIDX=1,
COTX=55,FWDX=1,UUSCCX=16,UUSCCY=8,FNIDX=1,
CLASSMRK=EC&G711&G729AOPT,TGRP=55,SRCHMODE=AB,INS=Y,SECLEVEL=TRA
DITIO,DEV=HG3550CO,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=0;
If more than 30 B channels are required, the set 1-1-10-1 can be identical.
A RICHT is required for the LCR:

ADD-RICHT:ART=LRTENEW,LRTE=55,LSVC=ALL,TGRP=55,DNNO=1-40-155;
You also need an outdial rule:
ADD-LODR:ODR=56,CMD=NPI,NPI=UNKNOWN,TON=UNKNOWN;
and an LDAT.
ADD-LDAT:LRTE=55,LSVC=ALL,LVAL=1,TGRP=55,ORD=56;
In the numbering plan, a digit pattern is configured according to regulations,
which is to be routed via the SIP carrier connection.
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="0"-"W"-"00"-"49"-
"1801"-"30200"-"XXXX", LRTE=55,LAUTH=1;
The following GKREG entry is not necessary and is only used for completeness,
as the LEGK does not resolve addresses:
ADD-
GKREG:GWNO=1,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1;
The KNDEF entry cancels out the system part of the incoming phone number:
ADD-KNDEF:NNO=1-40-155,TYPE=OWN,ISDNCC=49,ISDNAC=180130100;
4.4.3 Gateway Configuration in WBM

In the HG 3500 WBM under Explorer > Voice Gateway, you will find the menu
item SIP Trunk Profile. Here you will find preset profiles for the released service
providers. For a simulation, we use a general profile with registration.
A31003-H3160-S104-8-7620, 07/2014
The following settings are configured under this profile

(NatTrkWithRegistration):
• Domain name: supplied by the provider (here: iandc.training.com).
• IP address/hostname of the registrar: supplied by the provider (here DNS

name: sip.iandc.training.com).
• IP address/hostname of the proxy: supplied by the provider (here DNS

Figure 22 SIP service profiles in HG 3500 WBM (scenario 1)
Finally, enter the Account Name (right-click the menu item

NatTrkWithRegistration). In this example, you are registering under the system
number assigned to the connection by your provider.
Figure 23 SIP service profiles in HG 3500 WBM (scenrario 1)
A31003-H3160-S104-8-7620, 07/2014
Scenario 2: Gateway via Session Border Controller to SIP Carrier
4.5 Scenario 2: Gateway via Session Border Controller to SIP Carrier
4.5.1 Initial Situation

Key parameters:
DNS - service provider iandc.training.com (domain name) 2.3.3.123

SIP registrar / proxy sip.iandc.training.com 2.3.3.124
STNO carrier connection / SBC-WAN-1 +49180130100 3.3.3.1
STNO carrier connection / SBC-WAN-2 +49180130200 3.3.3.2
HG 3500 -1 (LAN) 1.40.11.82
SBC -1 (LAN) 1.40.11.89
Figure 24 HG 3500 via session border controller to SIP carrier
In this example, the scenario has changed as only one session border controller
(SBC) is switched between the SIP trunk gateway (HG 3500) and service
provider on the HiPath 4000 -1 system. The SIP trunk gateway is now configured
with an IP address from the customer LAN (1.40.11.82). The session border
controller has two IP addresses, 1.40.11.89 in the customer LAN and 3.3.3.1 in
the service provider LAN.
A session border controller is recommended when using HiPath 4000 SoftGates,

to increase security. It has Network Address Translation (NAT) and firewall
functionality.
In the case of AMO configuration in the HiPath 4000-1, only the HG 3500
changes. In the HG 3500 WBM, the session border controller is configured as the
interface to the service provider. Of course, the session border controller must
also be configured.
The HiPath 4000-1 system should always be dialed from the HiPath 4000-2
system using the digit pattern 0049180130200-xxxx.
A31003-H3160-S104-8-7620, 07/2014
Figure 25 SIP Service Profiles in HG 3500 WBM (scenario 2)
As in scenario 1, you can right-click the profile name in the Explorer bar to add
the account with the registration data. The registration name is the system
number in our example.
Figure 26 SIP Service Profiles in HG 3500 WBM (scenario 2)
4.5.2 AMO Configuration

Configuration is almost identical to scenario 1:
A31003-H3160-S104-8-7620, 07/2014
AMO BFDAT:
ADD-BFDAT:FCTBLK=3,FUNCTION=HG3550,BRDBCHL=BCHAN60&BCHAN120;
CHANGE-
BFDAT:CONFIG=CONT,FCTBLK=3,FUNCTION=HG3550,LINECNT=2,UNITS=3;
AMO BCSU:
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=10,PARTNO="Q2324-
X500",FCTID=1,LWVAR="0",FCTBLK=3,BCHAN3550=60,ALARMNO=0;
The HG 3550 IP address is entered in the AMO CGWB. In this case, it is an
address from the customer LAN:
ADD-CGWB:LTU=1,SLOT=10,SMODE=NORMAL,IPADDR=1.40.11.82,
NETMASK=255.255.255.0,BITRATE="AUTONEG",TRPRSIP=60,DNSIPADR=2.3.
3.123;
AMO CGWB:
CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=10,TYPE=LEGKDATA,GWNO=1,REGEXTGK=NO;
CHA-CGWB:MTYPE=CGW,LTU=1,SLOT=10,TYPE=SIPTRERH,GWAUTREQ=NO;
CHANGE-CGWB:MTYP=CGW,LTU=1,SLOT=10,TYPE=SIPTRSSA,SIPREQ=NO;
LCR:
ADD-BUEND:TGRP:=55,NAME="SIP CARRIER",NO=60;
ADD-COT:COTNO=55,COTPAR=ANS&CEBC&BSHT&BLOC&LWNC&NLCR&TSCS&
VNNO&NLCD&LINC&NOFT&NTON;
ADD-COP:COPNO=55,COPPAR=IMEX,TOLL=FBKW,TRK=FBKW;
ADD-TDCSU:ART=NEW,PEN=1-01-010-0,COTNO=55,COPNO=55,DPLN=0,VBZ=0,
COS=1,LCOSV=1,LCOSD=1,CCT="SIP CARRIER
",DESTNO=0,PROTVAR="ECMAV2",
SEGMENT=8,ATNTYP=CO,ISDNIP=00,ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY
, NNO=1-40-
155,ALARMNR=2,FIDX=1,COTX=55,FWDX=1,UUSCCX=16,UUSCCY=8,FNIDX=1,
CLASSMRK=EC&G711&G729AOPT,TGRP=55,SRCHMODE=AB,INS=Y,SECLEVEL=TRA
DITIO, DEV=HG3550CO,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=0;
ADD-RICHT:ART=LRTENEW,LRTE=55,LSVC=ALL,TGRP=55,DNNO=1-40-155;
ADD-LODR:ODR=56,CMD=NPI,NPI=UNKNOWN,TON=UNKNOWN;
ADD-LDAT:LRTE=55,LSVC=ALL,LVAL=1,TGRP=55,ORD=56;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="0"-"W"-"00"-"49"-
"1801"-"30200"-"XXXX", LRTE=55,LAUTH=1;
ADD-
GKREG:GWNO=1,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1;
ADD-KNDEF:NNO=1-40-155,TYPE=OWN,ISDNCC=49,ISDNAC=180130100;
A31003-H3160-S104-8-7620, 07/2014
4.5.3 HG 3500 Configuration in WBM

HG 3500 configuration in WBM corresponds almost exactly to scenario 1. In a
suitable SIP trunk profile (in this case: NatTrkWithRegistration) enter:
• Domain name: supplied by the provider (here: iandc.training.com).
• IP address/hostname of the registrar: supplied by the provider (here DNS

• IP address/hostname of the proxy: supplied by the provider (here DNS

• Outbound proxy: Different to scenario 1! Here, activate the checkbox under

Use outbound proxy and enter the IP address of the session border
controller in the LAN (IP address/hostname: 1.40.11.89). All calls are routed
to the SIP carrier from the HG 3500 via the SBC. The HG 3500 also only
permits incoming calls routed via the SBC.
• Inbound proxy: Not activated here! You can enter a proxy here, which will be
used especially for incoming calls.
A31003-H3160-S104-8-7620, 07/2014
As in scenario 1, you can right-click the profile name in the Explorer bar to add
registration data to the account. The registration name is the system number in
our example.
A31003-H3160-S104-8-7620, 07/2014
4.5.4 Configuration in the Session Border Controller

You have to configure the following parameters in the session border controller:
• Time settings
• IP address in the WAN (allocate by the service provider)
• IP address for the LAN1 interface
• DNS
• Firewall settings
• IP address of the SIP service provider
• SIP settings
• External IP address (WAN address)
• Internal IP address (LAN1 address)
• IP address for the netmask
• Configure as local gateway
• Configure as branch SBC
• Configure the HG 3500 IP address as gateway
A31003-H3160-S104-8-7620, 07/2014
config_ip_trunking_v6_sip.fm
Configuration of SIP-Q-Trunking / Native SIP Trunking
Configuration using AMOs
5 Configuration of SIP-Q-Trunking / Native SIP Trunking
5.1 Configuration using AMOs
IMPORTANT: In addition to the AMO configuration, the trunking partner must be

configured for a native SIP trunk or can be configured for a SIP-Q trunk in WBM
using the SIP trunk profiles (see Section 3.3, “SIP Trunk Profiles”).
5.1.1 Trunking Protocol

The same protocols must always be set in the AMO CGWB and AMO GKREG.
AMO CGWB AMO GKREG Protocol

TRPRSIP SIP native SIP
TPRSIPQ SIPQ SIP-Q V2
Table 4 Protocols in the AMOs CGWB and GKREG
5.1.2 Configuring a HG 3500 as a Local Gateway

The following diagram shows a HG 3500 scenario for a fictitious customer in
Frankfurt. It shows node 10-69-100 (Frankfurt-Bockenheim) and node 10-69-200
(Frankfurt-Sachsenhausen). Both systems have a common gateway board that
should be configured as HG 3500. LEGK should be active on both systems (two
local gateways). This constellation is relatively easy to explain because both
nodes can be configured more or less symmetrically. The figure shows all
necessary parameters. Node 10-69-100 is located in IP network 1.69.11.0/24 and
node 10-69-200 is located in IP network 1.69.21.0/24. The networks reach each
other over the routers Ra and Rb.
A31003-H3160-S104-8-7620, 07/2014
DEFRT DEFRT
STMI 2/4
HG
HG 3500
3500
Ra Rb
Router Router
IP Networ k
IPADDR: IPADDR:
1.69.11.80 1.69.21.80
NETMASK NETMASK:
255.255.255.0 255.255.255.0
Cus to me r LAN
Cust omer LAN

GWID: GWID:
TEST01 TEST02
GWNO: GWNO:
1 2
KN 10-69-100 KN 10-69-200
Figure 29 Configuration example: both nodes are LEGK
5.1.2.1 Configuration in Node 10-69-100
Start by configuring the board as HG 3500 in node 100. To avoid repeated

restarts, do not insert the board until configuration is complete.
Step 0:
Configure LEGK in node 10-69-100.
CHANGE-ZANDE:TYPE=ALLDATA,GATEKPR=YES;
Step 1:
The Common Gateway Board Q2316-X is configured as HG 3500. Q2316-X is
the version with 60 B channels. You can configure the board as a pure IP trunking
board or in mixed operation with IP trunking and LAN connectivity (WAML) and
many other features.
Configuration of the board for IP trunking only:

ADD-BFDAT:FCTBLK=1,FUNCTION=HG3550,BRDBCHL=BCHAN60&BCHAN120;
A31003-H3160-S104-8-7620, 07/2014
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3550,LINECNT=1,
UNITS=3; /* 30 B channels for HG3550 functionality (H323
trunking, 
SIP trunking, SIP subscriber)
CHANGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES; /* Close the
configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=37,PARTNO="Q2316-X",
FCTID=1,LWVAR="0",FCTBLK=1,BCHL3550=30,ALARMNO=0;
or
IP Trunking & WAML:

ADD-BFDAT:FCTBLK=1,FUNCTION=HG3550&WAML,
BRDBCHL=BCHAN60&BCHAN120;
UNITS=3; /* 30 B channels for HG3550 functionality (IP trunking,
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=WAML,UNITS,LINECNT=1;
/* Board will be configured with one circuit, i.e. 10 B channels
for WAML
configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=37,PARTNO=“Q2316-X
“,FCTID=1,LWVAR=“0“,FCTBLK=1,BCHL3550=30,BCHLWAML=10,ALARMNO=0;
Step 2:
The AMO CGWB allows the board to receive the IP address in the customer LAN
(LAN1), the subnet mask and the protocol variant (H323A / SIP-Q / NONE (board
is only configured for SIP subscribers).
IMPORTANT: Only one trunking protocol may be configured for each board!
There are no restrictions on interworking with other functions!
ADD-CGWB:LTU=1,SLOT=37,SMODE=NORMAL,
IPADDR=1.69.11.80,NETMASK=255.255.255.0,TRPRHSIPQ=10;
/*10 B channels for SIP-Q trunking
or
ADD-CGWB:LTU=1,EBT=37,SMODE=NORMAL,
IPADDR=1.69.11.80,NETMASK=255.255.255.0,TRPRHSIP=10; 
/*10 B channels for native SIP trunking
=> 20 B channels remain for other functions
Step 3:
The default router is now set in the customer LAN:
CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=GLOBIF,DEFRT=1.69.11.254;
A31003-H3160-S104-8-7620, 07/2014
Step 4:
The HG 3500 boards are administered using one gateway number (GWNO). This
number must also be unique.
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=LEGKDATA,GWNO=1;
Step 5:
Configuration without authentication and without registration (default values in
AMO CGWB.
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=LEGKDATA,GWNO=1,
REGEXTGK=NO;
SSA:
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=SIPTRSSA,SIPREG=NO;
ERH:
IMPORTANT: The SIPREG and REGEXTGK parameters must always have the
same value.
Step 6:
IMPORTANT: Multiple boards are permitted in one trunk group!
This step consists of several configuration commands. We need to set up the

trunk group and circuit, via which the B channels between gateway and HiPath
4000 are switched.
First you need a trunk group:

ADD-BUEND:TGRP=50,NAME="IP TRUNK GWID 1 ",NO=30,TRACENO=0,
ACDTHRH=*, PRIONO=2, TDDRFLAG=ON, GDTRRULE=0, ACDPMGRP=0,
CHARCON=NEUTRAL;
A digital trunk is then required (AMO TDCSU). The device type is HG3550IP (for
H323/H323A and native SIP/SIP-Q trunking). If you want to permit DMC, set
DMCALLWD=Y. This is only possible when the partner system supports DMC.
The <number> in the parameter LWPAR must identify the trunk as MASTER.
ADD-TDCSU:TYPE=NEW,PEN=1-01-037-0,COTNO=36,
COPNO=32,DPLN=0,ITR=0, COS=2,LCOSV=1,LCOSD=1,
CCTN="CIRCUIT from GW2",PROTVAR="ECMAV2",SEGMENT=8,
ISDNIP=00,ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY,
NNO=1-69-499,ALARMNO=12, COTX=36,CCHDL=SIDEA,CLASSMRK=EC&G711,
TCCID="IP RS",TGRP=50,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,
BCHANNEL=1&&30,BCNEG=N,BCGR=1,LWPAR=0,DMCALLWD=YES;
A31003-H3160-S104-8-7620, 07/2014
If DMC has been activated for the native SIP-/SIP-Q trunking path, Voice Activity
Detection should also be activated. Otherwise the same bandwidth is required for
the master connection as for the slave connection!
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYP=ASC,
PRIO=PRIO1,VAD=YES;
Otherwise the same bandwidth is required for the master connection as for the
slave connection.
IMPORTANT: It is recommended to reset the board:

RESET-BSSU:ADDRTYPE=PEN,LTG=1,LTU=1,SLOT=37;
IMPORTANT: The command CHANGE-FUNSU can prevent the complete

reloading of the STMI board.
Reloading is only necessary in the case of loadware changes.
CHANGE-FUNSU:PIT=FLASH,PARTNO="Q2316-X ",FCTID=2,
ACTION=RESET;
Step 7:
The LEGK must now still be informed about the existence of the HG 3500
gateway in the AMO GKREG. The GWNO must match the entry from the AMO
CGWB. In the case of a local gateway, the AMO GKREG automatically loads the
IP address (IPADR) from the AMO CGWB. You must also set the attributes
INTGW (internal -local- gateway) and HG3550V2 (version ID). The parameter
REGGW is not necessary because the gateway does not have to register at
another gateway.
ADD-GKREG:GWNO=1,GWATTR=INTGW&HG3550V2&SIPQ or
SIP,NUM=0,DPLN=0,LAUTH=1;
If a local gateway is configured, REGISTERED=NO is always displayed with
DISPLAY-GKREG;.
Step 8:
The same transport protocol (TCP, UDP) must be configured in all systems. The
transport protocol used can be set with WBM under Explorer > Voice Gateway
> SIP Parameters.
A31003-H3160-S104-8-7620, 07/2014
The HG 3500 board in node 10-60-100 is now configured properly and is

communicating with the LEGK. However, the gateway is still missing in the
partner node.
An LEGK should also be active in node 10-69-200. As the configuration

procedures for nodes 10-69-200 and 10-69-100 are identical, this section only
lists the appropriate AMO commands for the steps described above.
Step 0:
Step 1:
configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=2,SLOT=49,PARTNO="Q2316-X ",
A31003-H3160-S104-8-7620, 07/2014
Step 2:
IPADDR=1.69.21.80,NETMASK=255.255.255.0,TRPRHSIPQ=10;
IPADDR=1.69.21.80,NETMASK=255.255.255.0,TRPRHSIP=10;
Step 3:
CHANGE-
Step 4:
Step 5:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=LEGKDATA,
GWNO=2,REGEXTGK=NO;
SSA:
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=49,TYPE=SIPTRSSA,SIPREG=NO;
ERH:
IMPORTANT: The SIPREG and REGEXTGK parameters must always have the
same value.
Step 6:
ADD-BUEND:TGRP=50,NAME="IP TRUNK GWID 2 ",NO=30;
CCTN="CIRCUIT from GW2",PROTVAR="ECMAV2",SEGMENT=8,ISDNIP=00,
ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY,NNO=1-69-499,
ALARMNO=12, COTX=36,CCHDL=SIDEA,CLASSMRK=EC&G711,TCCID="IP RS",
TGRP=50,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,BCHANNEL=1&&30,BCNEG=N,B
CGR=1,LWPAR=0(=Master),DMCALLWD=YES;
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYP=ASC,PRIO=PRIO1,
VAD=YES;
Step 7:
The GKREG contains the configuration for both HG 3500 boards. Here,
GWNO=2 is now the local gateway in node 10-69-200 with the attributes INTGW
and HG3550V2 and SIPQ/SIP, while GWNO=1 (the partner gateway in node 10-
69-100) contains the attributes EXTGW, HG3550V2 and SIPQ/SIP in this system.
The parameter REGGW is not necessary because the gateway does not have to
register at another gateway.
ADD-GKREG:GWNO=1,GWATTR=EXTGW&HG3550V2&SIPQ or
SIP,GWIPADDR=1.69.11.80,DIPLNUM=0,DPLN=0,LAUTH=1;
A31003-H3160-S104-8-7620, 07/2014
ADD-GKREG:GWNO=2,GWATTR=INTGW&HG3550V2&SIPQ or
SIP,DIPLNUM=0,DPLN=0,LAUTH=1;
5.1.2.3 Extension in Node 10-69-100
The HG 3500 in node 10-69-200 must be retrofitted in node 10-69-100 for LEGK
(AMO GKREG). For node 10-69-100, this HG 3500 (GWNO=2) is an external
gateway (attributes EXTGW&HG3550V2&SIPQ/SIP) and is not registered in
node 10-69-100.
ADD-GKREG:GWNO=2,GWATTR=EXTGW&HG3550V2&SIPQ or
SIP,GWIPADDR=1.69.21.80,DIPLNUM=0,DPLN=0,LAUTH=1;
5.1.2.4 Call from Node 10-69-100 to Node 10-69-200
LCR should now be configured for node 10-69-100 in our example so that a
station using open numbering (UNKNOWN) in this node can reach a station in
node 10-69-200 over the IP trunk. Closed numbering or ISDN numbering plans
are also supported and configured in the same way.
A station in node 10-69-100 reaches node 10-69-200 over the tie number 902.
LRTE 520 should route to node 10-69-200 and use trunk group 50 (see above):
ADD-RICHT:MODE=LRTENEW,LRTE= 520,LSVC=ALL,
NAME="IP TO KN 69 200",TGRP=50,DNNO=1-69-499;
The following is a simple outdial rule:
ADD-LODR:ODR=520,INFO="TIE TO GW2";
Enter GW1=2-0 in LRTE 520 now. The 2 refers to the parameter GWNO in AMO
GKREG (section Section 5.1.2.3, “Extension in Node 10-69-100”). In AMO
GKREG for node 10-69-100, the HG 3500 with GWNO=2 is the IP address
1.69.21.80. The 0 stands for the sector path number. Sector path 0 means there
is unlimited bandwidth for this path. If the destination gateway is not reachable,
you can use the parameters GW2 to GW5 to configure an alternative route.
ADD-LDAT:LRTE=520,LSVC=ALL,LVAL=1,TGRP=50,ODR=520,
LAUTH=1,GW1=2-0;
IMPORTANT: In contrast to S0/S2 connections (point-to-point), an IP connection

is a point-to-multipoint connection and therefore the same trunk number is used
to the different destination gateways (GW1-GW5) in the AMO LDAT!
A31003-H3160-S104-8-7620, 07/2014
The tie number is entered in the AMO LDPLN. The directory number is entered
in the default dial plan with DIPLNUM=0. A profile index can also be used instead
of LRTE (AMO-LPROF):
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="902"-"X",
LRTE=520,LAUTH=1;
If you want to be able to reach node 10-69-100 from node 10-69-200, perform the
following configuration. You then point to the GWNO=1 in AMO LDAT.
5.1.3 Backup & Restore of the WBM Configuration

Data
All configuration data configured via the WBM of the board must be backed up
using the backup server. Otherwise all configuration data will be lost after a board
replacement, a reset of the board or loadware upgrade and the native SIP-/SIP-
Q trunking connection cannot be automatically reestablished. This is done with
the HiPath 4000 Assistant > Backup & Restore.
It is important to ensure that the backup server can be reached. If the backup
server is not available, the configuration data can also be saved in the flash
memory of the board and then can be retrieved from there.
HiPath 4000 Assistant > Backup & Restore
Configuration of a connection to backup server and HiPath 4000 Assistant.

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=MGNTDATA,
MGNTIP=<ip_address_assistant>,MGNTPN=<port_no_assistant>,
BUSIP=<ip_address_backup_server>,BUSPN=<port_no_backup_server>};
Note: The values for MGNTPN und BUSPN will not be restored after a reset of
the board. They have to be configured again manually.
Local Flash
IMPORTANT: It is recommended to additionally use the local flash as a backup

media. If the connection to the backup server is broken the configuration data will
be automatically restored from the local flash.
For more information please refer to "Gateways HG 3500 and HG 3575", Chapter
8, “Save Configuration Data in Local Flash ((local Backup & Restore)”.
A31003-H3160-S104-8-7620, 07/2014
IMPORTANT: If the restore is necessary (e.g. after an upgrade of the loadware)

and the backup server cannot be reached during the startup phase, the board is
loaded and put into operation with the default configuration. If the HBR server is
then reachable, the restore is carried out afterwards and a reboot with the new
configuration is triggered!

An additional reboot is also triggered during the startup phase if configurations/
data required for operation are restored (e.g. SPE certificates).
IMPORTANT: To avoid problems during upgrading/loadware swapping, a

backup should be initialized after exchanging the board because the backup is
associated with the MAC address.
5.1.4 Displaying Link Status

The link status of the LAN interface (link signal Ethernet, LAN speed, and LAN
interface) can be displayed at each level with the AMO SDSU using the usual
commands (PERI1, PERI2, and PERI3):
DISPLAY-SDSU:TYPE=PEN,LEVEL=PERI1,LTG=1,LTU=<ltu no>,
SLOT=<slot no>;
5.1.5 Procedure for Adding Supplementary HG 3500

Boards to the Network
Additional LEGKs can be configured in the same way as node 10-69-100. The
AMO BFDAT, AMO BCSU, AMO CGWB, AMO GKREG and AMO LDAT are then
in a single node.
IMPORTANT: The GKREG must recognize all HG 3500 boards in the network.
5.1.6 Relevant AMOs

Language
BCSU TYP=IPGW d CGW einrichten
A31003-H3160-S104-8-7620, 07/2014

Language
TYPE=IPGW e Configure CGW
BKAN3550 d Anzahl der B-Kanäle für IP-Trunking
BCHAN3550 e Number of b channels for IP trunking
BFDAT FUNCTION=HG3550 d CGW mit IP-Trunking
FUNCTION=HG3550 e CGW with IP trunking
BGBKAN d Maximale Anzahl der verfügbaren
B-Kanäle der Baugruppe (entweder
60 oder 120)
BRDBCHL e Maximum number of available b channels
(60 or 120)
ANZSATZ d Anzahl der Sätze für IP-trunking
LINECNT e Number of lines for IP trunking
UNITS e Defines the number of predefined blocks
with the selected function per line.
CGWB DEFRT d IP-Adresse des Default Routers
DEFRT e IP address of the default router
GWAUTREQ d Ziffern-Authentifizierung wird benötigt
GWAUTREQ e Digest authentication is required
GWREALM d Security Zone of the gateway
GWREALM e Security Zone of the gateway
GWRNR d Gateway Rufnummer
GWDIRNO e Gateway Directory Number
GWSECRET d Passwort des Gateways
GWSECRET e Password of the gateway
GWUSERID d User Identifizierung des Gateways
GWUSERID e User identification of the gateway
REGIP1 d IP-Addresse des primären SIP Registrars
REGIP1 e IP address of the primary SIP registrar
REGIP2 d IP-Addresse des sekundären
SIP Registrars
REGIP2 e IP address of the secondary SIP registrar
PORTTCP1 d Port Nummer für die primäre
SIP Registrierung über TCP/UDP
PORTTCP1 e Port number of the primary
SIP registration via TCP/UDP
PORTTCP2 d Port Nummer für die sekundäre SIP
Registrierung über TCP/UDP
A31003-H3160-S104-8-7620, 07/2014

Language
PORTTCP2 e Port number of the secondary
SIP registration via TCP/UDP
REGTIME d Zeit in Sekunden wie lange die
SIP-Registrierung gültig ist
REGTIME e Time in seconds the SIP registration is
valid
SIPREG d Gateway an einem SIP Registrar
registrieren
SIPREG e Register gateway at a SIP registrar
TRPRSIP d Anzahl der B-Kanäke für
Trunking-Protokoll SIP
TRPRSIP e Number of b channels for trunking
protocol SIP
TRPRSIPQ d Anzahl der B-Kanäke für
Trunking-Protokoll SIP-Q
TRPRSIPQ e Number of b channels for trunking
protocol SIP-Q
TYP=SIPTRSSA d SIP Trunking Daten für SSA (SIP Stack
Agent)
TYPE=SIPTRSSA e SIP trunking data for SSA (SIP Stack
Agent)
TYP=SIPTRERH d SIP Trunking Daten für ERH (Endpoint
Registration Handler)
TYPE=SIPTRERH e SIP trunking data for ERH (Endpoint
Regustration Handler)
GKREG GWATTR d Gateway Attribut
GWATTR e Gateway attribute
GWNR d Gateway ID (muss dem Eintrag im AMO
CGWB entsprechen)
GWNO e Gateway ID (must correspond to the
value in AMO CGWB)
TDCSU DMCERL=NEIN d DMC wird verhindert
DMCALLWD=NO e DMC not allowed
ZANDE GATEKPR=JA d PBX mit Gatekeeper
GATEKPR=YES e PBX with gatekeeper
A31003-H3160-S104-8-7620, 07/2014
Configuration with HiPath 4000 Assistant
5.2 Configuration with HiPath 4000 Assistant
5.2.1 Configure Common Gateway HG 3500

In order to configure a CGW board, you have to do the following:
• Step 1: Create function block
• Step 2: Search for a free slot
• Step 3: Open Board configuration menu in HiPath 4000 Assistant
• Step 4: Add new board
• Step 5: Fill in the mask
• Step 6: Open STMI2-IGW Board Data dialog and fill mandatory fields
Step 1: Create function block

Start CM > System Data > Board > CGW Function Block
Click Search for searching for a free function block number. Click New for adding
a new function block. Enter the required data and click Save.
Step 2: Search for a free slot

Before entering the LTU and SLOT number it is recommended to check if the
desired SLOT is free. To do this call: CM > System Data > Maintenance> Board
Maintenance.
Following the search in the object list view, free LTUs and SLOTs are marked with
NOGEN/NPR/UNACH in the Status Overview column.
A31003-H3160-S104-8-7620, 07/2014
Step 3: Open Board configuration menu in HiPath 4000 Assistant

CM > System Data > Board > Board
Step 4: Add new board

Press New button in order to add new board
Step 5: Fill in the mask
• Part Number: Q2316-X or Q2316-X10 or Q2324-X500 or Q2324-X510
• Function ID: is always 1
• Category: IPGW
• Board Name: STMI2 or STMI4
• CGW Function Block: enter previously created function block for trunking
(see Step 1: Create function block)
• LTU and SLOT: select a free slot (see Step 2: Search for a free slot)
A31003-H3160-S104-8-7620, 07/2014
Step 6: Open STMI2-IGW Board Data dialog and fill mandatory fields
Customer LAN IP Address and Subnet Mask.
Trunk Protocol: number of b-channels per protocol (e.g. SIP/SIPQ: 50).
IMPORTANT: Only one trunk protocol per board is supported! A combination of

different trunking protocols on one board is not possible!
After all required data has been entered in the relevant fields, press the Save
button.
The board is now added and can be found in Board Dialog or in Board
Maintenance.
5.2.2 Delete IPGW

To delete an IPGW board, proceed as follows:
• Step 2: Search for IPGW
• Step 3: Select IPGW and delete it

Step 2: Search for IPGW

Search Criteria > Category: IPGW
Step 3: Select IPGW and delete it

Choose the board that has to be deleted from the list and click Delete. After
pressing the Delete button, a message appears confirming deletion of the board
from the system.
5.2.3 Modify Board Data of IPGW

In order to modify board data, follow these steps:
• Step 2: Select IPGW
• Step 3: Carry out desired changes
• Step 4: Check the changes
A31003-H3160-S104-8-7620, 07/2014
Configuration using SIP Trunk Profiles in WBM

Step 2: Select IPGW

Select IPGW in the Category list and press the Search button.
Step 3: Carry out desired changes

Perform the necessary changes in the board dialog (e.g. IP address) and save
the changes with the Save button.
After saving the changes, a dialog confirming the successful action pops up.
Step 4: Check the changes

Make a new board search in order to check if new data has been accepted.
5.3 Configuration using SIP Trunk Profiles in WBM

see Section 3.3.7, “Configuration of SIP Trunks with/without Registration”.
5.4 SIP-Q Trunking between HiPath 4000 and OpenScape Voice

A connection between HiPath 4000 and OpenScape Voice can be established
using SIP-Q V2 trunks.
OpenScape Voice provides only a limited range of features over this connection.
For details, please refer to the OpenScape Voice documentation.
The phone numbers between HiPath 4000 and OpenScape Voice must be in
INTERNATIONAL format.
5.4.1 Restrictions
• Dialing with overlapping digits is not supported in OpenScape Voice
(overlapping reception is supported).
• With a HiPath 4000 - OpenScape Voice (Transit) - HiPath 4000 scenario, the
message waiting display is not routed via OpenScape Voice.
• HG 3500 does not support digit authentication.
• The payload partners can be defined with DMC in a HiPath4000 network. A

HiPath 4000 cannot however send the payload directly to or receive it directly
from OpenScape Voice partners. A hop always results on the HG 3500
module.
A31003-H3160-S104-8-7620, 07/2014
SIP-Q Trunking between HiPath 4000 and OpenScape Voice
• If there are more than two partners configured for the HG 3500 (e.g. Proxy) and
REGIP1 fails, REGIP2 remains registered until REGIP2 is no longer available.
Automatic switchback to REGIP1 is not possible.
5.4.2 HiPath 4000 Configuration

See also "Section 5.1, “Configuration using AMOs”.
The following settings must be configured differently from the

configuration given above:
• Configure the IP address
The IP address (IPADR), which is configured with the AMO CGWB, is the IP
address of the HiPath 4000. The IP address must be the same as the alias
name in OpenScape Voice.
• Configure the gateway phone number

To set up a SIP-Q trunking connection to an OpenScape Voice system, the
parameter GWRNO must be configured. This value of GWRNO must
correspond to the alias name in OpenScape Voice.
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=LEGKDATA,GWNO=1,
GWDIRNO=816901;
• Configure the external registrar
In case of a trunking connection to OpenScape Voice, the HiPath 4000 has
to register dynamically with the OpenScape Voice partner system. An
external registrar has to be set up for this purpose.
The external registrar is configured with the AMO CGWB.
• Operation at an external registrar (SIPREG=JA) must be activated.
• The duration of the registration validity must be entered in REGTIME. The

partner system registrar data must be entered in the fields REGIP
(OpenScape Voice address or proxy address) and REGPORT.
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=SIPTRSSA,
SIPREG=YES, REGIP1=127.28.45.54,PORTTCP1=5060,
REGTIME=<Seconds>,REGIP2=0.0.0.0,PORTTCP2=5060;
IMPORTANT: OpenScape Voice does not accept values less than 300
seconds in the REGTIME parameter.
• The parameter REGEXTGK must be set to YES in AMO CGWB.
A31003-H3160-S104-8-7620, 07/2014
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=LEGKDATA,GWNO=1,
GWDIRNO=816901REGEXTGK=YES;
IMPORTANT: The SIPREG and REGEXTGK parameters must always have

the same value.
• Configure authentication
If authentication is activated in the partner system, the authentication data
(SIP UserId in the field GWUSERID, password in the field GWSECRET and
realm in the field GWREALM) must be configured for registration on the
partner system. The transmission of authentication data can be activated and
deactivated using the parameter GWAUTREQ.
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=SIPTRERH,
GWAUTREQ=YES,GWSECRET=<string>,GWUSERID=<string>,
GWREALM=<string>;
• AMO TDCSU
– DESTNO must not be set to 0 (the value 0 deactivates loop detection).
– Set the parameter TRACOUNT to the number of hops permitted in your

network.
ADD-TDCSU:TYPE=NEW,PEN=1-01-037-0,COTNO=36,COPNO=32,
DPLN=0,ITR=0, COS=2,LCOSV=1,LCOSD=1,CCT="CIRCUIT from GW2",
DESTNO=81,PROTVAR="ECMAV2",SEGMENT=8, ISDNIP=00,ISDNNP=0,
TRACOUNT=10,SATCOUNT=MANY,NNO=1-69-1499,ALARMNO=12,
COTX=36,CCHDL=ASIDE,CLASSMRK=EC&G711,TCCID="IP RS",
TGRP=50,SRCHMODE=AB, INS=Y,DEV=HG3550IP,BCHAN=1&&30,
BCNEG=N,BCGR=1,LWPAR=0,DMCALLWD=Y;
• AMO COP
ADD-COP:COPNO=36,TOLL=TA,TRK=TA;
CHANGE-COP:COPNO=36,COPTYPE=COPADD,DEV=S2VERB,
INFO="36: S0/2 TIE ECMA2 AB V3.0";
• AMO COT
Also check whether the COT parameter TRCA is set.
ADD-COT:COTNO=200,
PAR=RCL&XFER&MELD&KNOR&CEBC&TIE&CBBN&CBFN&COTN&ANHT&BLOC&LWNC
&NLCR&ATRS&TSCS&DFNN&NLHT&NLRD&VCMN&SNBE&IICB&NCDR&NOFT&VNCO&
NOTO&NOSD&NPIS&PGEP&IBBA&PRNI&NTON&OSCV&FWDN&FNAN;
CHANGE-COT:COTNO=200,COTTYPE=COTADD,DEV=INDEP,INFO="HP8K";
Notes:
– If the entire network uses e164 numbering, the COT parameter NPIS
must be set for all digital trunks. If the dial plan UNKNOWN/UNKNOWN
is used, the parameter NPIS should NOT be set!
– The COT parameters FWDN and FWAN may cause problems if a

consistent dial plan is not used throughout the entire network.
A31003-H3160-S104-8-7620, 07/2014
– The COT parameter OSCV must be set.
• Configure block dialing

Block dialing must be set up for the trunking connection to OpenScape Voice.
• Note for national and local calls

Dialing with national numbers makes sense also for HiPath 4000 users.
Example: The extension +49(89)722-31256 can be reached under the
following numbers:
31256 If closed numbering is configured

000498972231256 Always
0-722-31256 Local call
0-089-722-31256 National call
If local or national dialing is desired by HiPath 4000 users, a number of other
special LCR configurations have to be performed. This configuration is
outside the scope of the current description because it is not relevant for
OpenScape Voice.
Example of closed numbering:
The LCR must also be configured for closed numbering .
This is an example of the destination number 31256.
DN 31256 remains for +49(89)722-31256
Use the e164 numbering scheme for HiPath 4000 / OpenScape Voice
interworking. The called subscriber's extension should also use e164 with the
dial plan ID ISDN in the internal ISDN messages.
Station number type: INTERNATIONAL
Missing digits must be filled with AMO LODR ##out pulse (e.g. 4989722).
AMO WABE defines the code
Example for:
DN 31256
NETRTE=224.
ADD-WABE:CD=224,DAR=NETRTE;
ADD-WABE:CD=31256,DAR=STN,CHECK=N;
CHANGE-WABE:CD=31256,DESTNO=218;
AMO RICHT sets up the bundle
Example for:
CD=224 (defined with AMO WABE)
LRTE=224 (used later with AMO LDAT)
TGRP=240 (preconfigured with AMO BUEND)
A31003-H3160-S104-8-7620, 07/2014
ADD-RICHT:MODE=CD,LRTE= 224,CD=224,CPS=0,LSVC=ALL,
NAME="HP 8K MEDIATRIX",TGRP1=240,DESTNO=240,DNNO=218,
PDNNO=1-1-218,ZEICHUM=NEUTRAL,KPRCAUL=NO,CLNAMEDL=NO;
ADD-RICHT:MODE=CD,CD=224,CPS=0,SRVC=VCE,TYPE=DTMF,M
FVCONF=FIX,DTMFPULS=PP300;
AMO LODR defines the outdial rule
Example for:
ODR=240 (use for AMO LDAT)
ADD-LODR:ODR=240,CMD=OUTPULSE,DGTS=4989722;
ADD-LODR:ODR=240,CMD=NPI,NPI=ISDN,TON=INTERNAT;
ADD-LODR:ODR=240,INFO="HP8K";
AMO LDAT defines LCR data
Example for:
TRRP240 (defined with AMO BUEND)
ODR=240 (defined with AMO LODR)
LRTE=224 (defined with AMO RICHT)
ADD-LDAT:LRTE=224,LSVC=ALL,LVAL=1,TGRP=240,ORD=240,
LAUTH=16,CARRIER=1,ZONE=EMPTY,LATTR=DMCEND,VCCYC=4;
5.4.3 OpenScape Voice Configuration

OpenScape Voice is configured with the OpenScape Voice Assistant.
Equivalent parameters must be configured in OpenScape Voice. The following

data must be correctly configured:
Configuration of endpoint profile
The endpoint profile must be created before the endpoints.
Open the list of endpoint profiles in OpenScape Voice Assistant with

OpenScape Voice > Business Group > Available Private Numbering Plan =
NP_Gateways > Profiles > Endpoint Profile.
Choose the relevant endpoint profile from the list (e.g. HP4K) or create a new
profile.
Tab General:
• Endpoint Profile:
– Name: HP4K
– Remark: <optional>
– Numbering Plan: NP_Gateways
A31003-H3160-S104-8-7620, 07/2014
• Management Information
– Class of Service: international
– Routing Area: H4K_Network
– Calling Location: <optional>
– Time Zone: LOCAL
– SIP Privacy Support: FULL
– Failed Call Intercept Treatment: Enabled
– Language: German
Tab Endpoints:
This tab contains a list of endpoints assigned to the current profile.
Tab Services:
• Voice Mail: Yes
• Call Transfer: Yes
• Call Forward Invalid Destination: No
• Toll and Call restrictions: No
Endpoint data that describes the connection to HiPath 4000
OpenScape Voice > Business Group > Members > Endpoints > Name
Tab General:
Definition of connection data for an endpoint. Define the name and the profile
here.
The Registered checkbox is activated automatically if the CGW has the status
registered.
Tab SIP:
Configuration of IP address and CGW port and general configuration for SIP-Q.
• Choose the option button SIP-Q Signaling.
• Enter (Static, Dynamic):
– If Static is entered here, HG 3500 (SIP) registration is not required.
– If Dynamic is entered, HG 3500 (SIP) registration is required.
• Signaling Binding Address: IP address of CGW (this parameter must

correspond with the parameter IPADDR in the AMO CGWB)
A31003-H3160-S104-8-7620, 07/2014
• Port: (this parameter must correspond with the parameter PORTTCP2 in the
AMO CGWB)
• Transport protocol: TCP
Tab Attributes:
Set Support of Best Effort SRTP to Enabled and activate the checkbox next to
Enable Session Timer.
Tab Aliases:
When configuring the endpoint displayed by HiPath 4000 (i.e. HG 3500), the
following parameters must correspond with the data configured in the AMO
CGWB:
• Name: This parameter must correspond with the parameter GWID1.
• IP Address of CGW: This parameter must correspond with the parameter

IPADDR.
• Aliases:
The ID of the gateway is used for dynamic registration. This is entered in the
AMO CGWB in the branch LEGKDATA in the parameter GWDIRNO.
Set the IP address of HiPath 4000 to "trusted".
OpenScape Voice > Administration > Signaling Management > Digest

Authentication > Realms > Add
Activate the checkbox Trusted Entry, enter the IP address of the CGW in the field
Signaling Primary and select All Ports.
Signaling and registration parameters that describe the OpenScape Voice

registration data (IP address, port, login)
The data entered here must correspond with the data entered in the AMO CGWB
for ERH or SSA.
The listening IP address must be entered in the IP address of the external

registrar.
The TCP/UDP port must be set in the field TCP/UDP Port.
The data set for authentication (UserID, Password, Realm) must correspond
with the data entered in the AMO CGWB in the data branch for SSA.
Aliases:
A31003-H3160-S104-8-7620, 07/2014
Number management between HiPath 4000 and OpenScape Voice for Italy
The ID of the gateway is used for dynamic registration. This is entered in the AMO
CGWB in the branch LEGKDATA in the parameter GWDIRNO.
IMPORTANT: You will find more detailed information on the OpenScape Voice
configuration in the relevant OpenScape Voice documentation.
5.5 Number management between HiPath 4000 and OpenScape Voice for
Italy
Because the phone number format for Italian mobile phones is different, the
phone numbers in the OpenScape Voice direction are modified incorrectly if the
following configuration information is not observed.
Scenario:
1. System A - HiPath 4000
2. System B - OpenScape Voice
Incoming trunk call to HiPath 4000 to an OpenScape Voice subscriber.
Requirements:
The phone numbers sent to OpenScape Voice must be in ISDN/
INTERNATIONAL format.
The HiPath 4000 must be configured as an Italian system.
Configure DAR=TIE in the central office direction:
Set up a separate direction to the central office for the Italian mobile phone
numbers:
ADD-RICHT:MODE=LRTENEW,LRTE=393,LSVC=ALL,
NAME=ITALIANMOBILE,TGRP=XX,DNNO=1-1-
393,ROUTOPT=NO,REROUT=NO,DESTNO=193,FWDSWTCH=YES;
ADD-LODR:ODR=393,CMD=NPI,NPI=ISDN,TON=UNKNOWN;
ADD-LDAT:LRTE=393,LSVC=ALL,TGRP=XX,ORD=393,LAUTH=1;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=0-W-3,LRTE=393,
LAUTH=1;
Set up a separate direction to the central office for the Italian mobile phone
numbers (if the phone number is dialed with a country code):
A31003-H3160-S104-8-7620, 07/2014
Number management between HiPath 4000 and OpenScape Voice for Italy
ADD-RICHT:MODE=LRTENEW,LRTE=394,LSVC=ALL,
NAME=ITALIANMOBILE,TGRP=XX,DNNO=1-1-
393,ROUTOPT=NO,REROUT=NO,DESTNO=193,FWDSWTCH=YES;
ADD-LODR:ODR=394,CMD=NPI,NPI=ISDN,TON=UNKNOWN;
ADD-LDAT:LRTE=394,LSVC=ALL,TGRP=xx,ORD=394,LAUTH=1;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=0-W-0039-3,LRTE=394,
LAUTH=1;
Create a KNDEF entry with TYPE=FOREIGN for the Italian mobile phone numbers:
ADD-KNDEF:NNO=1-1-393,TYPE=FOREIGN,ISDNCC=39;
Add the COT parameter DCCO to allow a node number to be derived:
CHA-COT:COTNO=YY,COTTYPE=COTADD,COTPAR=DCCO;
A31003-H3160-S104-8-7620, 07/2014
sip_conn_popups.fm
CLIP/CLIR,
CLIP - Calling Line Identification Presentation - The number of the calling party is
displayed at the called party.
CLIR - Calling Line Identification Restriction - The number of the calling party is
suppressed at the called party.
COLP/COLR,
COLP - Connected Line Identification Presentation - The number of the called

party is displayed at the calling party.
COLR - Connected Line Identification Restriction - The number of the called party
is suppressed at the calling party.
CSTA/ACL monitoring
CSTA/ACL monitoring provides the device status of SIP subscribers for BLF WIN
applications (Busy Lamp Field) or other presence-based applications.
CNIP/CNIR
CNIP - Calling Name Identification Presentation - The name of the calling party is
displayed at the called party.
CNIR - Calling Name Identification Restriction - The name of the calling party is
suppressed at the called party.
CNOP/CNOR
CNOP - Connected Name Identification Presentation - The name of the

connected party is displayed at the called party.
CNOR - Connected Name Identification Restriction - The name of the connected

party is suppressed at the called party.
attended call transfer
A is the initiator of the call transfer. A is in a call with B and puts B on hold. Then
A sets up a consultation call to C and initiates the transfer. After the transfer, B
and C are connected.
blind call transfer
A is the initiator of the call transfer. A is in a call with B. A puts B on hold. Then A
sets up a consultation call to C and transfers the call before the consultation call
is connected. After the transfer, B and C are connected.
Proxy
Server name / IP address of the server of the partner to which calls are routed.
A31003-H3160-S104-8-7620, 07/2014
sip_conn_popups.fm
Inbound proxy
Server name / IP address of the trunking partner from which the data is sent to
the HiPath 4000.
Outbound proxy
Server name/IP address to which all outgoing messages/data are sent as first
node/hop (e.g. session boarder controller).
A31003-H3160-S104-8-7620, 07/2014
h323_conn_01_overview.fm
Overview
H323 / H323 Annex Connectivity
1 Overview
IMPORTANT: SIP-Q is the recommended standard protocol for IP Trunking

since HiPath 4000 V5. This means in pure HiPath 4000 V5 and HiPath 4000 V6
networks SIP-Q should be used and not H323. 
SIP-Q is also the standard protocol for connecting to HiPath 3000 V8 upwards
and also to OpenScape Voice systems. 
In case of any problem with H323 trunking the SIP-Q protocol has to be used
instead.
Features
• CLIP / CLIR / COLP / COLR
• Name Display
• Hold / Retrieve / Toggle
• Transfer (blind, unattended, attended)
• Call forwarding
• Callback on busy subscriber / Callback no reply
• Message waiting indication
• Route optimization
• HiPath 4000 as survivability media gateway
• Signaling and payload encryption (TLS / SRTP)
• T38
Boards Used
The common gateway board HG 3500 is used. For details, see “Gateways HG
3500 and HG 3575”, Chapter 4, “Supported Gateways”.
A31003-H3160-S104-8-7620, 07/2014
h323_conn_01_overview.fm
Overview
A31003-H3160-S104-8-7620, 07/2014
h323_conn_02_dtmf_outband.fm
DTMF Outband Signaling
2 DTMF Outband Signaling

To activate the “DTMF Outband Signaling”, the following steps have to be made:
1. Deactivate RFC 2833 via AMO CGWB:

CHA-CGWB:MTYP=CGW,LTU=<ltu>,SLOT=<slot>,TYPE=ASC,RFCDTMF=NO;
To activate H.323 DTMF Outband Signaling, transmission of DTMF tones
according to RFC 2833 has to be deactivated. Against a widely held belief
transmission of DTMF tones according to RFC 2833 is not a DTMF Outband
Signaling, but an Inband Signaling using special codecs.
To deactivate it parameter RFCDTMF in AMO CGWB path ASC has to be set
to NO on both sides.
2. Activate “DTMF Outband Signaling” via WBM (Parameter DTMF Outband

Signaling)
WBM: Explorers > Payload > HW Modules
Figure 1 Activation of DTMF outband signaling
A31003-H3160-S104-8-7620, 07/2014
h323_conn_02_dtmf_outband.fm
DTMF Outband Signaling
A31003-H3160-S104-8-7620, 07/2014
config_ip_trunking_v6_h323.fm
3 Configuration Example
3.1 Configuration using AMOs
3.1.1 Trunking Protocol

The same protocols must always be set in the AMO CGWB and AMO GKREG.
AMO CGWB AMO GKREG Protocol

TRPRH323 H323 native H323
TPRH323A H323ANN H323 Annex
Table 1 Protocols in the AMOs CGWB and GKREG

If H323 Annex is set in the AMO CGWB/AMO GKREG, this protocol is only used
if it was also set in the peer or if the peer can use this protocol.
3.1.2 Configuring a HG 3500 as a Local Gateway

The following diagram shows a HG 3500 scenario for a fictitious customer in
Frankfurt. It shows node 10-69-100 (Frankfurt-Bockenheim) and node 10-69-200
(Frankfurt-Sachsenhausen). Both systems have a common gateway board that
should be configured as HG 3500. LEGK should be active on both systems (two
local gateways). This constellation is relatively easy to explain because both
nodes can be configured more or less symmetrically. The figure shows all
necessary parameters. Node 10-69-100 is located in IP network 1.69.11.0/24 and
node 10-69-200 is located in IP network 1.69.21.0/24. The networks reach each
other over the routers Ra and Rb.
A31003-H3160-S104-8-7620, 07/2014
DEFRT DEFRT
STMI 2/4
HG
HG 3500
3500
Ra Rb
Router Router
IP Networ k
IPADDR: IPADDR:
1.69.11.80 1.69.21.80
NETMASK NETMASK:
255.255.255.0 255.255.255.0
Cus to me r LAN
Cust omer LAN

GWID: GWID:
TEST01 TEST02
GWNO: GWNO:
1 2
KN 10-69-100 KN 10-69-200
Figure 2 Configuration example: both nodes are LEGK
Start by configuring the board as HG 3500 in node 100. To avoid repeated

restarts, do not insert the board until configuration is complete.
Step 0:
Configure LEGK in node 10-69-100.
Step 1:
The Common Gateway Board Q2316-X is configured as HG 3500. Q2316-X is
the version with 60 B channels. You can configure the board as a pure IP trunking
board or in mixed operation with IP trunking and LAN connectivity (WAML) and
many other features.
Configuration of the board for IP trunking only:

A31003-H3160-S104-8-7620, 07/2014
UNITS=3; /* 30 B channels for HG3550 functionality (H323
trunking, 
configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=37,PARTNO="Q2316-X",
or
IP Trunking & WAML:

ADD-BFDAT:FCTBLK=1,FUNCTION=HG3550&WAML,
BRDBCHL=BCHAN60&BCHAN120;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=WAML,UNITS,LINECNT=1;
/* Board will be configured with one circuit, i.e. 10 B channels
for WAML
configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=1,SLOT=37,PARTNO=“Q2316-X
“,FCTID=1,LWVAR=“0“,FCTBLK=1,BCHL3550=30,BCHLWAML=10,ALARMNO=0;
Step 2:
The AMO CGWB allows the board to receive the IP address in the customer LAN
(LAN1), the subnet mask and the protocol variant (H323A / SIP-Q / NONE (board
is only configured for SIP subscribers).
IMPORTANT: Only one trunking protocol may be configured for each board!
There are no restrictions on interworking with other functions!
ADD-
5.255.0,TPRH323A=10;/*10 B channels for H323A trunking
or
ADD-
5.255.0,TRPRH323=10;/*10 B channels for H323A trunking
=> 20 B channels remain for other functions
Step 3:
The default router is now set in the customer LAN:
CHANGE-
A31003-H3160-S104-8-7620, 07/2014
Step 4:
The HG 3500 requires an ID that is unique in the network. This is the parameter
GWID in AMO CGWB:
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=GWDATA,GWID1="TEST01";
GWID1 and GWID2 together form a contiguous value consisting of 128
characters. Entries are case-sensitive.
Step 5:
The HG 3500 boards are administered using one gateway number (GWNO). This
number must also be unique.
Step 6:
IMPORTANT: Multiple boards are permitted in one trunk group!
This step consists of several configuration commands. We need to set up the

trunk group and circuit, via which the B channels between gateway and HiPath
4000 are switched.
First you need a trunk group:

ADD-BUEND:TGRP=50,NAME="IP TRUNK GWID 1 ",NO=30,TRACENO=0,
ACDTHRH=*, PRIONO=2, TDDRFLAG=ON, GDTRRULE=0, ACDPMGRP=0,
CHARCON=NEUTRAL;
A digital trunk is then required (AMO TDCSU). The device type is HG3550IP (for
H323/H323A and native SIP/SIP-Q trunking). If you want to permit DMC, set
DMCALLWD=Y. This is only possible when the partner system supports DMC.
The <number> in the parameter LWPAR must identify the trunk as MASTER.
CCTN="CIRCUIT from GW2",PROTVAR="ECMAV2",SEGMENT=8,
ISDNIP=00,ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY,
NNO=1-69-499,ALARMNO=12, COTX=36,CCHDL=SIDEA,CLASSMRK=EC&G711,
TCCID="IP RS",TGRP=50,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,
BCHANNEL=1&&30,BCNEG=N,BCGR=1,LWPAR=0,DMCALLWD=YES;
If DMC has been activated for the H323-/H323A trunking path, Voice Activity
Detection should also be activated. Otherwise the same bandwidth is required for
the master connection as for the slave connection!
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYP=ASC,
PRIO=PRIO1,VAD=YES;
A31003-H3160-S104-8-7620, 07/2014
Otherwise the same bandwidth is required for the master connection as for the
slave connection.
IMPORTANT: It is recommended to reset the board:

RESET-BSSU:ADDRTYPE=PEN,LTG=1,LTU=1,SLOT=37;
IMPORTANT: The command CHANGE-FUNSU can prevent the complete

reloading of the STMI board.
Reloading is only necessary in the case of loadware changes.
CHANGE-FUNSU:PIT=FLASH,PARTNO="Q2316-X ",FCTID=2,
ACTION=RESET;
Step 7:
The LEGK must now still be informed about the existence of the HG 3500
gateway in the AMO GKREG. The GWNO must match the entry from the AMO
CGWB. In the case of a local gateway, the AMO GKREG automatically loads the
IP address (IPADR) from the AMO CGWB. You must also set the attributes
INTGW (internal -local- gateway) and HG3550V2 (version ID). The parameter
REGGW is not necessary because the gateway does not have to register at
another gateway.
ADD-GKREG:GWNO=1,GWATTR=INTGW&HG3550V2&H323ANN or
H323,NUM=0,DPLN=0,LAUTH=1;
If a local gateway is configured, REGISTERED=NO is always displayed with
DISPLAY-GKREG;.
The HG 3500 board in node 10-60-100 is now configured properly and is

communicating with the LEGK. However, the gateway is still missing in the
partner node.
An LEGK should also be active in node 10-69-200. As the configuration

procedures for nodes 10-69-200 and 10-69-100 are identical, this section only
lists the appropriate AMO commands for the steps described above.
Step 0:
Step 1:
A31003-H3160-S104-8-7620, 07/2014

configuration
ADD-BCSU:TYPE=IPGW,LN=1,LTU=2,SLOT=49,PARTNO="Q2316-X ",
A31003-H3160-S104-8-7620, 07/2014
Step 2:
ADD-
5.255.0, TPRH323A=10;
or
ADD-
5.255.0, TRPRH323=10;
Step 3:
CHANGE-
Step 4:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=GWDATA,GWID1="TEST02";
Step 5:
Step 6:
ADD-BUEND:TGRP=50,NAME="IP TRUNK GWID 2 ",NO=30;
CCTN="CIRCUIT from GW2",PROTVAR="ECMAV2",SEGMENT=8,ISDNIP=00,
ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY,NNO=1-69-499,
ALARMNO=12, COTX=36,CCHDL=SIDEA,CLASSMRK=EC&G711,TCCID="IP RS",
TGRP=50,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,BCHANNEL=1&&30,BCNEG=N,B
CGR=1,LWPAR=0(=Master),DMCALLWD=YES;
CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYP=ASC,PRIO=PRIO1,
VAD=YES;
Step 7:
The GKREG contains the configuration for both HG 3500 boards. Here,
GWNO=2 is now the local gateway in node 10-69-200 with the attributes INTGW
and HG3550V2 and H323ANN or H323, while GWNO=1 (the partner gateway in
node 10-69-100) contains the attributes EXTGW, HG3550V2 and H323ANN or
H323 in this system. The parameter REGGW is not necessary because the
gateway does not have to register at another gateway.
ADD-GKREG:GWNO=1,GWATTR=EXTGW&HG3550V2&H323ANN or
H323,GWIPADDR=1.69.11.80,DIPLNUM=0,DPLN=0,LAUTH=1;
ADD-GKREG:GWNO=2,GWATTR=INTGW&HG3550V2&H323ANN or
H323,DIPLNUM=0,DPLN=0,LAUTH=1;
A31003-H3160-S104-8-7620, 07/2014
3.1.2.3 Extension in Node 10-69-100
The HG 3500 in node 10-69-200 must be retrofitted in node 10-69-100 for LEGK
(AMO GKREG). For node 10-69-100, this HG 3500 (GWNO=2) is an external
gateway (attributes EXTGW&HG3550V2&H323ANN or H323) and is not
registered in node 10-69-100.
ADD-GKREG:GWNO=2,GWATTR=EXTGW&HG3550V2&H323ANN or
H323,GWIPADDR=1.69.21.80,DIPLNUM=0,DPLN=0,LAUTH=1;
3.1.2.4 Call from Node 10-69-100 to Node 10-69-200
LCR should now be configured for node 10-69-100 in our example so that a
station using open numbering (UNKNOWN) in this node can reach a station in
node 10-69-200 over the IP trunk. Closed numbering or ISDN numbering plans
are also supported and configured in the same way.
A station in node 10-69-100 reaches node 10-69-200 over the tie number 902.
LRTE 520 should route to node 10-69-200 and use trunk group 50 (see above):
ADD-RICHT:MODE=LRTENEW,LRTE= 520,LSVC=ALL,
NAME="IP TO KN 69 200",TGRP=50,DNNO=1-69-499;
The following is a simple outdial rule:
ADD-LODR:ODR=520,INFO="TIE TO GW2";
Enter GW1=2-0 in LRTE 520 now. The 2 refers to the parameter GWNO in AMO
GKREG (section Section 3.1.2.3, “Extension in Node 10-69-100”). In AMO
GKREG for node 10-69-100, the HG 3500 with GWNO=2 is the IP address
1.69.21.80. The 0 stands for the sector path number. Sector path 0 means there
is unlimited bandwidth for this path. If the destination gateway is not reachable,
you can use the parameters GW2 to GW5 to configure an alternative route.
ADD-LDAT:LRTE=520,LSVC=ALL,LVAL=1,TGRP=50,ODR=520,
LAUTH=1,GW1=2-0;
IMPORTANT: In contrast to S0/S2 connections (point-to-point), an IP connection

is a point-to-multipoint connection and therefore the same trunk number is used
to the different destination gateways (GW1-GW5) in the AMO LDAT!
The tie number is entered in the AMO LDPLN. The directory number is entered
in the default dial plan with DIPLNUM=0. A profile index can also be used instead
of LRTE (AMO-LPROF):
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="902"-"X",
LRTE=520,LAUTH=1;
A31003-H3160-S104-8-7620, 07/2014
If you want to be able to reach node 10-69-100 from node 10-69-200, perform the
following configuration. You then point to the GWNO=1 in AMO LDAT.
3.1.3 Backup & Restore of the WBM Configuration

Data
All configuration data configured via the WBM of the board must be backed up
using the backup server. Otherwise all configuration data will be lost after a board
replacement, a reset of the board or loadware upgrade and the H323-/H323A
trunking connection cannot be automatically reestablished. This is done with the
HiPath 4000 Assistant > Backup & Restore.
It is important to ensure that the backup server can be reached. If the backup
server is not available, the configuration data can also be saved in the flash
memory of the board and then can be retrieved from there.
HiPath 4000 Assistant > Backup & Restore
Configuration of a connection to backup server and HiPath 4000 Assistant.

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=37,TYPE=MGNTDATA,
MGNTIP=<ip_address_assistant>,MGNTPN=<port_no_assistant>,
BUSIP=<ip_address_backup_server>,BUSPN=<port_no_backup_server>};
Note: The values for MGNTPN und BUSPN will not be restored after a reset of
the board. They have to be configured again manually.
Local Flash
IMPORTANT: It is recommended to additionally use the local flash as a backup

media. If the connection to the backup server is broken the configuration data will
be automatically restored from the local flash.
For more information please refer to "Gateways HG 3500 and HG 3575", Chapter
8, “Save Configuration Data in Local Flash ((local Backup & Restore)”.
IMPORTANT: If the restore is necessary (e.g. after an upgrade of the loadware)

and the backup server cannot be reached during the startup phase, the board is
loaded and put into operation with the default configuration. If the HBR server is
then reachable, the restore is carried out afterwards and a reboot with the new
A31003-H3160-S104-8-7620, 07/2014
configuration is triggered!

An additional reboot is also triggered during the startup phase if configurations/
data required for operation are restored (e.g. SPE certificates).
IMPORTANT: To avoid problems during upgrading/loadware swapping, a

backup should be initialized after exchanging the board because the backup is
associated with the MAC address.
3.1.4 Displaying Link Status

The link status of the LAN interface (link signal Ethernet, LAN speed, and LAN
interface) can be displayed at each level with the AMO SDSU using the usual
commands (PERI1, PERI2, and PERI3):
DISPLAY-SDSU:TYPE=PEN,LEVEL=PERI1,LTG=1,LTU=<ltu no>,
SLOT=<slot no>;
3.1.5 Procedure for Adding Supplementary HG 3500

Boards to the Network
Additional LEGKs can be configured in the same way as node 10-69-100. The
AMO BFDAT, AMO BCSU, AMO CGWB, AMO GKREG and AMO LDAT are then
in a single node.
IMPORTANT: The GKREG must recognize all HG 3500 boards in the network.
3.1.6 Relevant AMOs

Language
BCSU TYP=IPGW d CGW einrichten
TYPE=IPGW e Configure CGW
BKAN3550 d Anzahl der B-Kanäle für IP-Trunking
BCHAN3550 e Number of b channels for IP trunking
BFDAT FUNCTION=HG3550 d CGW mit IP-Trunking
FUNCTION=HG3550 e CGW with IP trunking
A31003-H3160-S104-8-7620, 07/2014

Language
BGBKAN d Maximale Anzahl der verfügbaren
B-Kanäle der Baugruppe (entweder
60 oder 120)
BRDBCHL e Maximum number of available b channels
(60 or 120)
ANZSATZ d Anzahl der Sätze für IP-trunking
LINECNT e Number of lines for IP trunking
UNITS e Defines the number of predefined blocks
with the selected function per line.
CGWB DEFRT d IP-Adresse des Default Routers
DEFRT e IP address of the default router
GWID1 d Gateway ID
GWID1 e Gateway ID
GKREG GWATTR d Gateway Attribut
GWATTR e Gateway attribute
GWNR d Gateway ID (muss dem Eintrag im AMO
CGWB entsprechen)
GWNO e Gateway ID (must correspond to the
value in AMO CGWB)
TDCSU DMCERL=NEIN d DMC wird verhindert
DMCALLWD=NO e DMC not allowed
ZANDE GATEKPR=JA d PBX mit Gatekeeper
GATEKPR=YES e PBX with gatekeeper
3.2 Configuration with HiPath 4000 Assistant
3.2.1 Configure Common Gateway HG 3500

In order to configure a CGW board, you have to do the following:
• Step 1: Create function block
• Step 2: Search for a free slot
• Step 4: Add new board
A31003-H3160-S104-8-7620, 07/2014
• Step 5: Fill in the mask
• Step 6: Open STMI2-IGW Board Data dialog and fill mandatory fields
Step 1: Create function block

Start CM > System Data > Board > CGW Function Block
Click Search for searching for a free function block number. Click New for adding
a new function block. Enter the required data and click Save.
Step 2: Search for a free slot

Before entering the LTU and SLOT number it is recommended to check if the
desired SLOT is free. To do this call: CM > System Data > Maintenance> Board
Maintenance.
Following the search in the object list view, free LTUs and SLOTs are marked with
NOGEN/NPR/UNACH in the Status Overview column.
A31003-H3160-S104-8-7620, 07/2014

Step 4: Add new board

Press New button in order to add new board
Step 5: Fill in the mask
• Part Number: Q2316-X or Q2316-X10 or Q2324-X500 or Q2324-X510
• Function ID: is always 1
• Category: IPGW
• Board Name: STMI2 or STMI4
• CGW Function Block: enter previously created function block for trunking
(see Step 1: Create function block)
• LTU and SLOT: select a free slot (see Step 2: Search for a free slot)
Step 6: Open STMI2-IGW Board Data dialog and fill mandatory fields
Customer LAN IP Address and Subnet Mask.
Trunk Protocol: number of b-channels per protocol (e.g. H323/H323-Annex:

50).
IMPORTANT: Only one trunk protocol per board is supported! A combination of

different trunking protocols on one board is not possible!
After all required data has been entered in the relevant fields, press the Save
button.
A31003-H3160-S104-8-7620, 07/2014
The board is now added and can be found in Board Dialog or in Board
Maintenance.
3.2.2 Delete IPGW

To delete an IPGW board, proceed as follows:
• Step 2: Search for IPGW
• Step 3: Select IPGW and delete it

Step 2: Search for IPGW

Search Criteria > Category: IPGW
Step 3: Select IPGW and delete it

Choose the board that has to be deleted from the list and click Delete. After
pressing the Delete button, a message appears confirming deletion of the board
from the system.
3.2.3 Modify Board Data of IPGW

In order to modify board data, follow these steps:
• Step 2: Select IPGW
• Step 3: Carry out desired changes
• Step 4: Check the changes

Step 2: Select IPGW

Select IPGW in the Category list and press the Search button.
Step 3: Carry out desired changes

Perform the necessary changes in the board dialog (e.g. IP address) and save
the changes with the Save button.
After saving the changes, a dialog confirming the successful action pops up.
A31003-H3160-S104-8-7620, 07/2014
Step 4: Check the changes

Make a new board search in order to check if new data has been accepted.
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
spe_01_feature_description.fm
Feature Description
Signaling and Payload Encryption (SPE)
Signaling and Payload Encryption (SPE)
The "Signaling and Payload Encryption" feature encompasses the encryption of
payload data and signaling data within HiPath 4000 systems or between such
systems and the associated endpoints. Additionally calls in networks with HiPath
3000 V7 (and higher) and OpenScape Voice V3.1 R2 (and higher) are transferred
encrypted.
A PKI (Pubic Key Infrastructure) is needed to use signaling and payload

encryption. For more information, see Section 1.3.1, “PKI (Public Key
Infrastructure)”.
1.1 Encrypted Signaling and Payload Connections

As of HiPath 4000 V6, security for all signaling and payload streams passed
through an IP network by means of encryption is supported.
Exception:
• SIP subscribers
• Native SIP trunks CGW: encrypted signaling but plain payload
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Encrypted Signaling and Payload Connections
Figure 1 Encrypted signaling and payload connections HiPath 4000 V6
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Scenarios - Overview
Figure 2 Encrypted signaling and payload connections HiPath 4000 SoftGate
HiPath 4000 V6 Common Gateway HiPath 4000 SoftGate/VHG

3500
Native SIP Trunk TLS TLS + SDES
SIP-Q Trunk TLS + MIKEY TLS + MIKEY or SDES
HFA subscriber TLS + MIKEY TLS + MIKEY
SIP subscriber --- ---
Table 1 Signaling and payload encryption (IP environment)
1.2 Scenarios - Overview

Signaling and payload encryption is supported in the following scenarios:
• IP trunking (see Section 3.3.2, “SPE for IP Trunking”)
• HFA terminals (see Section 3.4.2, “SPE for IP Terminals”)
• IPDA (see Section 3.5, “Activation / Deactivation of SPE for Access Points”)
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Solution Concepts
• HiPath 4000 SoftGate (see Section 3.6, “HiPath 4000 SoftGate SPE
Activation / Deactivation”)
• Analog and TDM terminals (see Section 3.4.1, “SPE for Analog/TDM
Endpoints”)
• Analog and TDM trunking connections (see Section 3.3.1, “SPE for Analog /
TDM Trunks”)
1.3 Solution Concepts
1.3.1 PKI (Public Key Infrastructure)
Figure 3 Public Key Infrastructure (PKI) using the example of common

gateways
A Public Key Infrastructure (PKI) is needed to use the "Signaling and Payload
Encryption" feature. You can either use an existing customer PKI for this or apply
a new PKI using Deployment Service DLS (DLS V3 or higher).
The necessary certificates are centrally deployed to all HiPath 4000 gateways
and terminals via DLS.
The PKI for HiPath 4000 included in DLS
• features a basic PKI solution for customers who do not have a PKI (certificate
creation),
• supports the integration of an existing PKI (certificate provision for customer

PKI),
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Solution Concepts
• performs automatic certificate deployment.
Customer with PKI

If the customer already has a PKI, the following factors must be considered:
• The existing certificate must be allowed for encryption and signing.
• The existing certificate is an RSA certificate.
• Because of performance issues the existing certificate has a maximum key

length of 1024 bits.
• The existing certificate is in PEM or PKCS #12 format.
Customer without PKI

If the customer does not have a PKI, the necessary certificates can be created
with DLS. The Automatic SPE Configuration function in the Administration
menu is used for this.
Detailed information on DLS

For more information on importing and distributing certificates, see Chapter 6,
“Deployment Service (DLS)”.
1.3.2 Signaling encryption
Figure 4 Signaling encryption
The PEP (Proprietary Encryption Protocol) is based on the Master Encyrption

Key (MEK). PEP is used to protect signaling for connections between a host
system and access points (IPDA and HiPath 4000 SoftGate).
For all other signaling connections, the TLS (Transport Layer Security) protocol
is used (e.g. HFA phones, IP trunking (H.323/SIP)).
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Solution Concepts
In the case of VoIP signaling paths in a HiPath 4000 network or to partner

systems (such as OpenScape Voice), every connection is individually and
independently encrypted. TLS/SSL encryptions (SIP/H.323/HFA) and AES
encryption based on pre-shared secrets (IPDA/DMC) is used for this. End-to-end
encryption is based on an unbroken encrypted chain of partial signaling links.
The TLS/SSL connections remain permanently active and are renewed at regular
intervals. The time interval for renegotiation is set in the WBM:
WBM > Explorer > Security > (right-click) Signaling and Payload Encryption
(SPE) > Edit Security Configuration > Maximum Re-Keying interval [hours]
Figure 5 Time interval for re-keying
• HFA subscriber
CorNet-TC/TS and H.323 signaling between gateways and HFA stations is
secured by a "server-authenticated" TLS connection, that is, the HFA stations
check the certificates supplied by the gateway.
• CorNet-IP/SIP-Q trunking
H.323/SIP signaling (including Cornet-NQ messages) between two gateways
is secured by a "mutual-authenticated" TLS connection, in other words both
gateways verify the identity of the partner based on the certificate delivered.
• Native SIP Trunking

SIP signaling is secured by means of a "mutual-authenticated" TLS
connection, i.e. both gateways verify the partner identity on the basis of the
certificate supplied, or a "server-authenticated" TLS connection, i.e. the
gateway checks the certificate supplied by the partner.
• DMC connections
Signaling (H.225) is secured with H.235.1 (authentication and integrity) for
the DMC connections. The "shared-secret" (key) needed is generated by the
HiPath 4000 for every call and distributed to the DMC endpoints. This means
that DMC connections are not encrypted, they are only authenticated.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Solution Concepts
1.3.3 Voice Encryption
Figure 6 Voice Encryption
SRTP is used for all connections (HFA, SIP, IPDA) for payload encryption. SRTP
is based on the Advanced Encryption Standard (AES). Depending on the
connection type MIKEY, SDES or MEK is used for encryption.
For this purpose, the endpoints generate (cryptographically) random 128-bit long
keys. The key exchange between the participating communication partners takes
place in the framework of signaling (see Section 1.3.2, “Signaling encryption”).
Depending on the connection type, MIKEY, SDES or internal HiPath 4000
mechanisms are used for generating or exchanging keys.
All keys are essentially only used once, i.e. they apply exclusively for the duration
of the relevant voice connection. Stations are shown a message as to whether the
call is end-to-end encrypted.
IPDA
Because there are no signaling connections for IPDA media streams the usage
of MIKEY for key agreement is not possible. Instead following concept will be
implemented:
• DNIL (DB) generates a call specific SRTP master encryption key and some
other SRTP parameters e.g. key length, salt key.
• CP conveys this SRTP parameters within the PATH_SWITCH message to the

involved parties
• MPH uses the newly added parameters to generate the same SRTP
parameter set as provided by MIKEY and forwards it via MAL to MSC.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
MIKEY (Multimedia Internet KEYing)
1.4 MIKEY (Multimedia Internet KEYing)
Figure 7 MIKEY
MIKEY is a form of key management for realtime multimedia communication and

facilitates the exchange of keys and other security parameters between stations.
In VoIP, MIKEY can be used to exchange the master key and other security
parameters to ensure secure SRTP transmission between terminals. MIKEY is
described in RFC 3830 “MIKEY: Multimedia Internet KEYing".
1.4.1 MIKEY Option 0

MIKEY Option 0 is used if the signaling connection is secured via TLS (Hop-by-
Hop). This is ensured for all end-to-end payload streams for the (DMC) master
connection of a HiPath 4000 node in which all sections support signaling
encryption.
Thus, no certificates are needed for MIKEY Option 0 itself but the HiPath systems
or their gateways need an own (server) certificate plus private key for TLS
purposes.
All involved entities need the certificate of that/these CAs that issue the
certificates for the HiPath systems / gateways.
If CRL (Certificate Revocation List) checks are required by the configuration, the
CRL DP (CRL Distribution Point - HTTP/LDAP-URL) is required by every
endpoint and must therefore also be distributed.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Session Description (SDES) Protocol
1.4.2 MIKEY Option 1

MIKEY Option1 is used for DMC slave connections only as these cannot be
secured via TLS.
The required symmetric encryption key needed therefore is generated on a per

call basis by the HiPath system and distributed to the DMC endpoints via secured
network links.
IMPORTANT: No certificates are required by MIKEY Option 1 itself.
1.5 Session Description (SDES) Protocol

The "Advanced Encryption Standard (AES)" encryption system can be used for
payload encryption on the vHG3500 for SIP connections along with SDES as the
encryption attribute. SDES is described in RFC 4568 "Session Description
Protocol (SDP) Security Descriptions for Media Streams".
The vHG 3500 supports crypto suites with 80-bit authentication and 32-bit
authentication and SRTP with optional m lines.
IMPORTANT: SDES is not supported on the CGW.
1.6 Master Encryption Key (MEK)

The MEK (Master Encryption Key) is used for HiPath Access/HiPath 4000
SoftGate signaling connections.
1.7 Secure SIP Connections

Restrictions:
• Security is not supported for SIP subscribers.
• Payload encryption with SDES is not supported on the CGW.
• Payload encryption with MIKEY is not supported on the native SIP trunk.
The security settings that are possible depending on the connection type and
gateway are listed in the next table:
A31003-H3160-S104-8-7620, 07/2014
Feature Description
Secure SIP Connections
Security CGW vHG 3500

SIP Subscriber
Signaling encryption --- ---
Payload encryption --- ---
SIP-Q Trunk
Signaling encryption
TLS ok ok
Payload encryption
SRTP with MIKEY - Key Management ok ok
SRTP with SDES - Key Exchange --- ok
Native SIP Trunk
Signaling encryption
TLS ok ok
Payload encryption
SRTP with MIKEY - Key Management --- ---
SRTP with SDES - Key Exchange --- ok
Table 2 Possible encryption depending on the connection type and gateway
1.7.1 SIP-Q Trunking

If all requirements for SPE are fulfilled in a HiPath 4000 system (see Chapter 3,
“Configuration”), the gateway will try to set up a secure SIP-Q connection to the
partner gateway.
If no SIP-Q profile is activated (see "SIP-Connectivity > Section 3.3, “SIP Trunk
Profiles”"), then the payload is encrypted with MIKEY.
If a SIP-Q profile is activated, then payload encryption can be configured on the

vHG3500.
WBM > Explorer > Voice Gateway > SIP Trunk Profiles > Select suitable SIP-
Q trunk profile (right-click) > Edit
Figure 8 RTP security mode on the vHG3500 for a SIP-Q trunk
A31003-H3160-S104-8-7620, 07/2014
Feature Description
1.7.2 Native SIP trunking

If a HiPath 4000 system fulfills all requirements for SPE (see Chapter 3,
“Configuration”), the gateway will try to set up a secure SIP connection to the
partner gateway if this is configured in the SIP trunk profile (see SIP Connectivity
> Section 3.3, “SIP Trunk Profiles”).
The payload encryption mode cannot be configured for native SIP trunking. In the
case of native SIP trunk profiles, the security settings that were defined when the
relevant partner was released are used.
If signaling and payload encryption is released for a native SIP trunking partner,
the desired security mode can be configured in the SIP trunk profile (see "SIP
Connectivity > Section 3.3, “SIP Trunk Profiles”"). The configuration options are
dependent on the released security mode.
WBM > Explorer > Voice Gateway > SIP Trunk Profiles > Select suitable
native SIP-Q trunk profile (right-click) > Edit
Figure 9 SIP trunking security mode for a native SIP trunk profile with SPE
If a HiPath 4000 system fulfills all requirements for SPE (see Chapter 3,
“Configuration”) and if security is activated in the profile, then the gateway will try
to set up a secure connection to the partner gateway.
A31003-H3160-S104-8-7620, 07/2014
Feature Description
A31003-H3160-S104-8-7620, 07/2014
spe_02_service_info.fm
Service Information
Restrictions
2.1 Restrictions
• IP connections to a CA4000 system are not encrypted, in other words the
application data transmitted over this interface is unprotected but can be used
without restriction.
• This feature is not compatible with "Signaling and Payload Encryption" in

HiPath 4000 V3.0, i.e. encrypted signaling and payload cannot be transmitted
in a network with HiPath 4000 V3.0.
In a network with HiPath 4000 V3.0, it is not possible to encrypt the trunking
path between the two systems. HiPath 4000 V3.0's internal encryption can be
activated, however, within HiPath 4000 V3.0.
• If encryption has been activated on an STMI2/NCUI2+ board, the number of

configured channels must be 33% less than when encryption is deactivated.
For the exact number of B channels, see "Gateways HG 3500 und HG 3575",
Section 3.6, “B Channels”.
• SIP subscribers do not support encryption. That means that you cannot
activate SPE for SIP subscribers. For a complete list of terminals that support
"Signaling and Payload Encryption", see Section 3.4.2, “SPE for IP
Terminals”.
• As of HiPath 4000 V6, signaling encryption is supported in the common

gateway for native SIP trunks. This is not the case with payload encryption.
2.2 Generation of a Certificate

With the function Automatic SPE Configuration of the DLS it is possible to
generate a certificate and to distribute it to the gateways and endpoints. This is
especially useful when there is no client PKI. For more information please refer
to Chapter 8, “AutoSPE Configuration”.
Alternatively, a certificate can be generated on a common gateway board.
For manually generated certificates (PKCS#12 file) in case of STMI4/NCUI4

boards , the signature algorithm SHA-1 has to be used when generating
certifcates due to some board (VxWorks) restrictons.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Supported Certificates
2.3 Supported Certificates

The following certificates can be imported:
• CA certificates (*.crt, *.cer) from the certification authority
• Certificates in the format Public Key Cryptography Standards #12 (PKCS

#12) (*.p12)
• Certificates in the format X.509 PEM
An expired certificate cannot be reloaded. If a certificate expires in the course of

implementation, a HISTA message is issued along with an Error message. The
system continues to use the certificate, however.
IMPORTANT: Certificates should be replaced when their validity expires.
The certificate for Secure Trace features a number of unique characteristics (see
Chapter 4, “Secure Trace”).
HISTA message
Error message
F5881 with Error Cause: CERTIFICATE EXPIRED
2.4 Board Replacement

If certificates are lost (for example, when loading a board following board
replacement), they can be reloaded by means of the customary
"Backup&Restore" mechanism (logical DATA Backup). The same applies to the
MEKs during access point/HiPath 4000 SoftGate encryption.
IMPORTANT: Only a valid certificate can be loaded on the gateway.
2.5 Standby CGW Board

Standby CGW board is supported in SPE. It applies if a backup was made by
means of the customary Backup&Restore mechanism (logical DATA Backup).
This ensures that the standby board will take the same certificates and
configuration like the active board.
A31003-H3160-S104-8-7620, 07/2014
Service Information
Activating/Deactivating SPE for Subfunctions in the System
Restriction
Secure connections that are configured using the SIP trunk profiles are not
supported.
2.6 Activating/Deactivating SPE for Subfunctions in the System

SPE subfunctions can be deactivated - and in some cases even reactivated -
without a restart. This allows service personnel to deactivate specific SPE sub
functions in problem situations, on the one hand, to verify if the problem is caused
by SPE and, on the other hand, to pinpoint the cause of the fault. For more
information please refer to the following sections:
• Section 3.2, “Activation / Deactivation of SPE for Gateways with AMO

CGWB”
• Section 3.3, “Trunk SPE Activation / Deactivation”
• Section 3.4, “Terminal SPE Activation / Deactivation”
• Section 3.5, “Activation / Deactivation of SPE for Access Points”
• Section 3.6, “HiPath 4000 SoftGate SPE Activation / Deactivation”
2.7 Connection to Gateway Boards

There are several options for connecting to an active gateway board or which is
in startup process and for collecting data.
A31003-H3160-S104-8-7620, 07/2014
Service Information
SPE in Connection with Mobile HFA
Connection to gateway via ... CGW vHG 3500

V24 connection: With this connection it is yes no
possible to collect data and communicate with
the board before startup is complete.
SSH: With a SSH client (as TeraTerm, Putty) it yes no
is possible to connect when the IP
communication is available.
SSH via HiPath 4000 Assistant under Expert yes no
Mode > HG 35xx Telnet / SSH on an active
board, if HiPath 4000 Assistant has IP routing
access.
WBM connection on an active board if IP routing yes yes
access is possible.
Table 3 Connection to Gateway Boards
IMPORTANT: With the first three (1-3) connections it is possible to "reset

bootstrapping" on the active STMI boards.
2.8 SPE in Connection with Mobile HFA
2.8.1 Terminology used
SPEcapable client: A client actually logged in as TRADITIONAL client but that

is SPE capable and provided with all credential and
configurations for connecting as SECURE or CIPHER
client.
TRADITIONAL client: A client actually logged in as TRADITIONAL client and NOT
SPE capable at all (e.g. optiPoint 500).
SECURE and CIPHER client
TRADITIONAL client
SPEcapable client
A31003-H3160-S104-8-7620, 07/2014
Service Information
2.8.2 Prerequisite
The same protocol (TCP or TLS) must be used for the connection to the
gateway for the VISITED and HOME station in order to avoid that a VISITED
station using TCP can disconnect a HOME station using TLS (Dos attacks).
A HOME station connected via TCP that is disconnected by a VISITED station

connected via TLS is unable to disconnect the VISTED station and therefore
cannot reconnect to its gateway again.
2.8.3 Scenarios with Homogenous HiPath 4000

Network with SPE Enabled
IMPORTANT: Valid as of HiPath 4000 V4!
Visted
Home Secure/Cipher Traditional SPEcapable
Secure/Cipher does not work critical1 2
Traditional no problems3 no problems no problems
SPEcapable no problems4 no problems no problems
1 SPEcapable clients have to use TLS when acting as VISITED stations for a SECURE /
CIPHER client.
2 This scenario is critical due to PIN and H.235 password transfer over insecure
network links.
3 Secure/Cipher clients have to use TCP when acting as visited stations for a traditional
client.
4 Secure/Cipher clients have to use TCP when acting as visited stations for a SPEcapable
client.
IMPORTANT: The VISITED station already gets the protocol to be used for
connecting to the HOME gateway from the SPE Mobile HFA call flows.
A31003-H3160-S104-8-7620, 07/2014
Service Information
2.8.4 Scenarios within a Network with SPE activated

Nodes and SPE deactivated Nodes
HOME and VISITED: SPE deactivated and TRADITIONAL/SPEcapable
HOME:
• SPE deactivated
• phones: TRADITIONAL/SPEcapable
VISITED:
• SPE deactivated
HOME: SPE deactivated and TRADITIONAL/SPEcapable, VISITED: SPE

activated and TRADITIONAL/SPEcapable and SECURE/CIPHER
HOME:
• SPE deactivated
VISITED:
A31003-H3160-S104-8-7620, 07/2014
Service Information
• SPE activated
• phones: TRADITIONAL/SPEcapable and SECURE/CIPHER
HOME: SPE activated and TRADITIONAL/SPEcapable and SECURE/

CIPHER, VISITED: SPE activated and TRADITIONAL and SPEcapable and
SECURE/CIPHER
HOME:
• SPE activated
VISITED:
• SPE activated
• phones: TRADITIONAL and SPEcapable and SECURE/CIPHER
A TRADITIONAL client (without SPE support) is never accepted as a VISITED

station for a SECURE or CIPHER client. Call processing on the VISITED switch
is aware of this and rejects the remote login attempt with "Remote Login not
possible" (before asking the user to enter his/her PIN).
HOME: SPE activated and TRADITIONAL/SPEcapable and SECURE/

CIPHER, VISITED: SPE activated and TRADITIONAL and SPEcapable
HOME:
• SPE activated
VISITED:
• SPE activated
• phones: TRADITIONAL and SPEcapable
A31003-H3160-S104-8-7620, 07/2014
Service Information
A TRADITIONAL client (without SPE support) is never accepted as a VISITED

station for a SECURE or CIPHER client. Call processing on the VISITED switch
is aware of this and rejects the remote login attempt with "Remote Login not
possible" (before asking the user to enter his/her PIN).
2.8.5 Network Wide Usage of Mobile HFA

If TRADITIONAL clients are accepted both as HOME and VISITED stations on a
HiPath 4000 with SPE activated, this offers significant improvements in the usage
of the Mobile HFA feature within homogenous HiPath 4000 1(with or without SPE
activated) networks.
IMPORTANT: Mobile HFA cannot be used in networks between HiPath 4000

(as of version 4) systems with SPE activated and HiPath 4000 V2.0 / V3.0.
1. As of HiPath 4000 V4
A31003-H3160-S104-8-7620, 07/2014
spe_03_configuration.fm
Configuration
3 Configuration
Before configuring the Signaling and Payload Encryption (SPE) feature in a
HiPath 4000 system, make sure that all prerequisites are met (see Section 3.1,
"Prerequisites"). Once this has been assured, you can configure the individual
functions as required.
Short overview of the necessary steps for activation / deactivation of the SPE
feature on a HiPath 4000 system.
1. Activation / deactivation of SPE for subscriber gateways

Activation of this feature will encrypt the signaling / payload between
endpoints (subscriber gateways, vHG 3500, IP terminal, etc.) with TLS/SRTP.
This is configured with the PKI (Public Key Infra-structure) process. Activation
/ deactivation in the system is performed with AMO ZANDE. Make sure to use
the correct secure port: TLSP (for HFA and H323) / PORTTLS1 (for SIP)
parameter from AMO CGWB. The default values are 4061 / 5061. For more
information, please refer to Section 3.2, “Activation / Deactivation of SPE for
Gateways with AMO CGWB”.
IMPORTANT: The key material for trunking and HFA is exchanged for
gateways in an Access Point/HiPath 4000 SoftGate via the HSR connection.
If the HSR connection is not secure then the key material is exposed in clear
text. SPE must therefore also be activated for HiPath 4000 SoftGate/IPDA
Access Points (see Section 3.5, “Activation / Deactivation of SPE for Access
Points”).
2. Activation / deactivation of SPE for trunks

Activation of this feature will encrypt the signaling / payload on the trunk.
Activation / deactivation is performed by changing the security mode in AMO
TDCSU, AMO GKREG. For more information, please refer to Section 3.3,
“Trunk SPE Activation / Deactivation”.
3. Activation / deactivation of SPE for terminals

Activation of this feature will encrypt the signaling / payload between
terminals and the gateways. Activation / deactivation is performed by
changing the security mode of the subscribers with AMO SDAT / WBM. For
more information, please refer to Section 3.4, “Terminal SPE Activation /
Deactivation”.
4. Activation / deactivation of SPE for access points

Activation will encrypt the signaling / payload between established HSR
connections with PEP (Proprietary Encryption Protocol) / SRTP. This feature
is configured by the SPE administration client process. Activation /
deactivation in the system is performed with AMO SIPCO. For more
A31003-H3160-S104-8-7620, 07/2014
Configuration
Prerequisites
information, see Section 3.5, “Activation / Deactivation of SPE for Access

Points”.
5. Activation / deactivation of SPE for HiPath 4000 SoftGate

Activation will encrypt the signaling / payload between established HSR
connections with PEP (Proprietary Encryption Protocol) / SRTP. This feature
is configured by the MEK administration client process. For more information
please see Section 3.6, “HiPath 4000 SoftGate SPE Activation /
Deactivation”.
3.1 Prerequisites
System
The following prerequisites must be met before you can activate SPE in a system:
• All (v)HG 3500 gateways in this system must be assigned SPE certificates
and at least one CA certificate.
• All NCUI2 boards must be replaced by NCUI2+ or NCUI4.
• All (v)NCUI boards must have Master Encryption Keys (MEKs) configured.
• All components must be synchronized via the NTP server.
IMPORTANT: Do not use Assistant as an NTP server for IP phones, as it is

not supported. It has a limited number of buffers which makes it unreliable in
large deployments.
For more information on date/time settings and time synchronisation please

refer to “Section 2 - System Components (Hardware, Software)” of the service
manual, “Time Synchronization in the HiPath 4000 System”.
3.2 Activation / Deactivation of SPE for Gateways with AMO CGWB

Activation of SPE on the gateways will encrypt communication between the
endpoints with TLS / SRTP. For information on certificate distribution / activation
on the /gateways, please see Chapter 7, “Distribution of Certificates with the
WBM of the Gateway”.
IMPORTANT: The key material for trunking and HFA is exchanged for gateways
in an Access Point/HiPath 4000 SoftGate via the HSR connection. If the HSR
connection is not encrypted, the key material will be displayed in plain text. SPE
must therefore also be activated for Access Points/HiPath 4000 SoftGate (see
Section 3.5, “Activation / Deactivation of SPE for Access Points” or Section 3.6,
A31003-H3160-S104-8-7620, 07/2014
Configuration
Activation / Deactivation of SPE for Gateways with AMO CGWB
“HiPath 4000 SoftGate SPE Activation / Deactivation”).
All components should be time synchronized otherwise activation of SPE

between components will fail.
For better protection against errors in case of losing certificates, a backup server
should be configured for each board and also a backup should be made for every
new certificate that is installed on the board by means of the customary
"Backup&Restore" mechanism (logical DATA Backup).
The following steps have to be performed for activating SPE on a gateway:
– Deploy certificates for each board that need to be secure. Bootstrapping

should be made (in case DLS is used for deployment of certificates)
before the distribution of the certificates. For more information, please
refer to Chapter 6, “Distribution of Certificates to Gateways”. For
information on connection options with gateways, please refer to Section
2.7, “Connection to Gateway Boards”.
– Activation of SPE for trunks and IP terminals. For more information,

please refer to Chapter 3, “Trunk SPE Activation / Deactivation” and
Chapter 3, “Terminal SPE Activation / Deactivation”.
– Activation of SPE for gateways with AMO ZANDE.
Activation / deactivation of SPE for gateways:

CHANGE-ZANDE:TYPE=SECURITY,SPESUPP=YES;
If parameter SPESUPP is set to YES, SPE is enabled!
Parameters:
SPESUPP (YES/NO): Activates SPE for this system.
IMPORTANT: You must perform a hard restart on the system after you have
activated SPE. Do not forget to make an update of the system before the restart
EXEC-UPDAT:UNIT=BP,SUSY=ALL;. If you have a duplex system you have to
perform the following command on both processors simultaneously (at the same
time). This means all LTUs and APs will restart! 
EXEC-REST:TYPE=UNIT,UNIT=BP,RSLEVEL=HARD;
A default security level that is used when configuring new trunks or stations can
be defined with AMO ZANDE:
CHA-ZANDE:TYPE=SECURITY,SECTDMSB=<sec_level_subs_TDM>,
SECTDMTR=<sec_level_trunks TDM>,SECIPSB=<sec_level_ip_subs>,
SECIPTR=<sec_level_IP_trunks>;
Parameters:
A31003-H3160-S104-8-7620, 07/2014
Configuration
Trunk SPE Activation / Deactivation
SECTDMSB Security level for TDM subscribers.

(TRADITIO/SECURE): Default value : TRADITIO
SECTDMTR Security level for TDM trunks
(TRADITIO/EXTSECUR): Default value : TRADITIO
SECIPSB Security level for IP subscribers
(STANDARD/SECURE/CIPHER): Default value : SECURE:
SECIPTR Security level for IP trunks
(TRADITIO/STANDARD/SECURE/EXTSECUR): Default value : SECURE:
SECLVDSP Security terminal display
YES / NO Default value : N
3.3 Trunk SPE Activation / Deactivation
3.3.1 SPE for Analog / TDM Trunks
IMPORTANT: Activation / Deactivation of SPE for analog / TDM trunks requires

a restart of the board.
IMPORTANT: The configuration of analog and TDM trunks has no effect on their
behavior. The only purpose of this configuration is the determination of end-to-
end encryption points. The connection is then treated by call processing as if
encrypted but it isn't really encrypted. The other side of the trunk must also be a
HiPath 4000 configured as EXTSECUR. Note that SPE activation on CO trunks
(both digital and analog) is not possible.
CHANGE-TDCSU:PEN=<port equipment number>,

SECLEVEL=<security_level>;
The security level (SECLEVEL) can feature the following values:
TRADITIO: Nonsecure trunk

Default value for TDM trunks
EXTSECUR : This trunk is encrypted by a mechanism (such as VPN) that is different
from this feature. This trunk is therefore treated by call processing as
"fully encrypted" but not encrypted by HiPath 4000. The other side of
the trunk must also be a HiPath 4000 configured as EXTSECUR.
A31003-H3160-S104-8-7620, 07/2014
Configuration
3.3.2 SPE for IP Trunking
IMPORTANT: Depending on the gateway and the trunk type, various payload
encryptions are possible for IP trunking (see Table 1, “Signaling and payload
encryption (IP environment)”).
IMPORTANT: Activation / Deactivation of SPE for IP trunking requires a restart

of the board.
The following steps have to be performed:
1. Configuring the trunk

The AMO TDCSU is used for basic trunk configuration:
CHANGE-TDCSU:PEN=<port equipment
number>,SECLEVEL=<security_level>;
Security level (SECLEVEL) can feature the following values:
TRADITIO: Nonsecure trunk

Default value for TDM trunks
STANDARD SRTP (payload encryption) is not supported, only signaling
encryption (TLS-secured)
SECURE Full encryption (SRTP + TLS-secured)
Default value for IP trunks
EXTSECUR : This trunk is encrypted by a mechanism (such as VPN) that is
different from this feature. This trunk is therefore treated by call
processing as "fully encrypted" but not encrypted by HiPath 4000.
The other side of the trunk must also be a HiPath 4000 configured
as EXTSECUR.
IMPORTANT: The same security level will be set for all trunks associated
with a board.
2. Configuring the gateway
a) Configuring the remote gateway (EXTGW)

CHANGE-
GKREG:GWNO:=<gateway_number>,SECLEVEL=<SECURITY_level>;
b) Configuring the internal (local) gateway (INTGW)
The security level of the internal gateway is set via AMO TDCSU (with the
command CHANGE-TDCSU). With AMO GKREG you can only display the
actual security level but can't modify it. To modify the security level use
AMO TDCSU.
A31003-H3160-S104-8-7620, 07/2014
Configuration
If the security level configured with the AMO TDCSU is not displayed for
the internal gateway in AMO GKREG, this could be because:
• SPE is not active (check with AMO ZANDE) or
• certificates are not available, faulty or expired (for more information,

refer to the WBM/DLS and AMO HISTA, AMO BCSU, AMO SDSU).
3. Security parameters of SIP trunk profile
A SIP trunk profile can be activated for SIP-Q trunks and must be activated for
native SIP trunks (see “SIP Connectivity > Section 3.3, “SIP Trunk Profiles””).
• SIP-Q trunk profile

If a SIP-Q trunk profile is used, RTP security mode can be configured in vHG
3500.
WBM > Explorer > Voice Gateway > SIP Trunk Profiles > Select Profile
(right-click) > Edit
The default value is secure Payload (MIKEY) with fallback to insecure.
Figure 10 SIP trunk profile, SIP-Q, security parameters
• Native SIP trunk profile

If a native SIP trunk profile is used, SIP trunk security mode can be
configured if security is released for these partners.
WBM > Explorer > Voice Gateway > SIP Trunk Profiles > Select Profile
(right-click) > Edit
The default value is No Security.
Figure 11 SIP trunk profile, native SIP
AMO BCSU
Detailed information can be found in AMO BCSU with the command DISPLAY-
BCSU:TYPE=TBL,LTG=<ltg>,LTU=<ltu>,SLOT=<slot>; in the
SECURITY STATUS section.
A31003-H3160-S104-8-7620, 07/2014
Configuration
AMO SDSU
Detailed information can be found in AMO SDSU with the command DISP-
SDSU;. Refer to SECURITY LEVEL in the output.
<DISPLAY-
SDSU:STATUS=ALL,TYPE=PEN,LEVEL=PER3,LTG=1,LTU=1,SLOT=14;
DISPLAY-SDSU:STATUS=ALL,TYPE=PEN,LEVEL=PER3,LTG=1,LTU=1,SLOT=14;
H500: AMO SDSU STARTED
LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.014 STMI4 A Q2324-X510 READY
LAN CONN. . . . . . . . . . . READY
LINK SIGNAL ETHERNET . . . .
PRESENT
LAN SPEED . . . . . . . . . 100 MBIT/S
LAN INTERFACE . . . . . . . . FDX (FULL
DUPLEX)
CCT FUNCTION BLOCK
0 HG3570_2
1 - 2 HG3550_2
3 - 12 HG3530_2
13 - 22 HG3540_2
CCT LINE STNO SI BUS TYPE
001 2401 PP NW READY
MULTLINE 10 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (HG3550IP)
LINE: 2401 STNO: SI:
001 . . . . . . . . TMD CONN ISDN READY
A31003-H3160-S104-8-7620, 07/2014
Configuration

011 NO CONN
012 NO CONN
013 NO CONN
014 NO CONN
015 NO CONN
016 NO CONN
017 NO CONN
018 NO CONN
019 NO CONN
020 NO CONN
A31003-H3160-S104-8-7620, 07/2014
Configuration
021 NO CONN
022 NO CONN
023 NO CONN
024 NO CONN
025 NO CONN
026 NO CONN
027 NO CONN
028 NO CONN
029 NO CONN
030 NO CONN
SECURITY LEVEL . . . . . . . (CONF.) "SECURE"
(ACT.) "SECURE"
002 2402 NOGEN
003 2403 OPTI ONLY READY
MULTLINE 8. . . . . . . . . . . . . . .READY
000 NO CONN
001 SUBUNIT . . . . . DIGITE MAIN READY
(ALT_ROUT: N) (OPTIIP )
LINE: 2470 STNO: 24054 SI:VCE
001 . . . . . . . . DIGITE SUB A READY
003 . . . . . . . . DIGITE SUB C READY
002 NO CONN
003 NO CONN
004 NO CONN
005 NO CONN
006 NO CONN
007 NO CONN
008 NO CONN
(ACT.) "TRADITIO"
MULTLINE 8. . . . . . . . . . . . . . .READY
000 NO CONN
A31003-H3160-S104-8-7620, 07/2014
Configuration

002 NO CONN
003 NO CONN
004 NO CONN
005 NO CONN
006 NO CONN
007 NO CONN
008 NO CONN
SECURITY LEVEL . . . . . . . (CONF.) "CIPHER"
(ACT.) "CIPHER"
MULTLINE 8. . . . . . . . . . . . . . .READY
000 NO CONN
002 NO CONN
003 NO CONN
004 NO CONN
005 NO CONN
006 NO CONN
007 NO CONN
008 NO CONN
(ACT.) "SECURE"
MULTLINE 8. . . . . . . . . . . . . . .READY
000 NO CONN
001 SUBUNIT . . . . . DIGITE MAIN TRS
001 . . . . . . . . DIGITE SUB A UNACH
A31003-H3160-S104-8-7620, 07/2014
Configuration

003 . . . . . . . . DIGITE SUB C UNACH
002 NO CONN
003 NO CONN
004 NO CONN
005 NO CONN
006 NO CONN
007 NO CONN
008 NO CONN
(ACT.) "UNKNOWN"
MULTLINE 8. . . . . . . . . . . . . . .READY
000 NO CONN
001 SUBUNIT . . . . . DIGITE MAIN TRS
003 . . . . . . . . DIGITE SUB C UNACH
002 NO CONN
003 NO CONN
004 NO CONN
005 NO CONN
006 NO CONN
007 NO CONN
008 NO CONN
(ACT.) "UNKNOWN"
008 2408 NOGEN
009 2409 NOGEN
010 2410 NOGEN
011 2411 NOGEN
012 2412 NOGEN
013 2413 PP S0 READY
ELEM DEV. . . . . . SB FCT TERM READY
(ALT_ROUT: N) (S0PP )
A31003-H3160-S104-8-7620, 07/2014
Configuration

(ACT.) "TRADITIO"
(ACT.) "UNKNOWN"
015 2415 NOGEN
016 2416 NOGEN
017 2417 NOGEN
018 2418 NOGEN
019 2419 NOGEN
(ACT.) "UNKNOWN"
(ACT.) "UNKNOWN"
022 2422 NOGEN
A31003-H3160-S104-8-7620, 07/2014
Configuration
Terminal SPE Activation / Deactivation
3.3.3 Deactivation of SPE for SIP-Q / Native SIP

Trunking
Deactivating SPE
IMPORTANT: SPE can be deactivated without reboot.
The reduction of the security level from SECURE to TRADITIO for a partner
gateway (AMO GKREG, parameter SECLEVEL) means that all subsequent calls
are set up via TCP or UDP. SPE is therefore deactivated for all subsequent calls
to the relevant partner gateway.
The ongoing calls are maintained on TLS just as the TLS connection is
maintained, even if all associated calls are ended. gateway itself also remains in
secure mode.
IMPORTANT: If you want to deactivate SPE for incoming calls from this partner
gateway, you must also reconfigure the AMO GKREG at the partner system
(parameter SECLEVEL=TRADITIO).
Activating SPE
SPE can be activated without reboot.
As for deactivation, again with the AMO-GKREG.
IMPORTANT: gateway must already be in secure mode.

Do not overlook possible changes in the partner system when performing
activation (AMO GKREG, SECLEVEL=SECURE).
3.4 Terminal SPE Activation / Deactivation

Both the terminal and the HiPath 4000 system have to be configured accordingly
so that signaling and payload encryption will function for IP terminals.
A31003-H3160-S104-8-7620, 07/2014
Configuration
3.4.1 SPE for Analog/TDM Endpoints
IMPORTANT: The configuration of analog and TDM endpoints has no effect on

their behavior. The only purpose of this configuration is the determination of end-
to-end encryption. The connection is then treated by call processing as if
encrypted but it isn't really encrypted.
CHA-SDAT:STNO=<station
number>,TYPE=DATA1,CLASSSEC=<security_level>;
The security level (CLASSSEC) can feature the following values:
TRADITIO: Nonsecure endpoint

Default value.
SECURE Full encryption (SRTP + TLS-secured)
The phone is secured by external means but not encrypted by HiPath
4000. Call processing will consider this phone as a fully secure phone.
3.4.2 SPE for IP Terminals
IMPORTANT: SPE is not supported for SIP subscribers!
The following IP terminals are supported:
• optiPoint 410 (HFA)
IMPORTANT: Only signaling encryption and not payload encryption is

supported by optiPoint 410 Entry and Economy phones. Full SPE support is
possible from optiPoint 410 Economy Plus.
• optiPoint 420 (HFA)
IMPORTANT: Only signaling encryption and not payload encryption is

supported by optiPoint 420 Economy phones. Full SPE support is possible
from optiPoint 420 Economy Plus.
• OpenStage HFA
• AC-Win IP
• OpenScape Personal Edition
A31003-H3160-S104-8-7620, 07/2014
Configuration
3.4.3 Configuration
1. Configuring the IP terminal
The AMO SDAT is used for basic terminal configuration:
CHANGE-SDAT:STNO=<station
number>,TYPE=DATA1,CLASSSEC=<security_level>;
The security level (CLASSSEC) can feature the following values:
SECURE: These terminals are allowed to connect to the HFA board with TLS
or TCP depending on the terminal settings (WBM/DLS). That means
that this terminal can be fully secure (SRTP+TLS) or traditionally
non-secure, i.e. no signaling or payload encryption. This can be set
via WBM/DLS of the terminal. The AMO SDAT configuration stays
SECURE in both cases (setting of the terminal secure or non-
secure).
Default value.
CIPHER: These terminals allow only fully encrypted direct connections. This
means that the connection to the system logged on and each DMC
connection must be encrypted.
This setting provides the highest security but may lead to a lower
connection quality.
This setting is only applicable for HFA endpoints.
If a terminal is configured as CIPHER, SPE must not be deactivated
on the terminal (WBM/DLS).
IMPORTANT: There is no separation between payload and signaling

encryption: either both are active or not active.
IP terminals can only be configured as SECURE or CIPHER in AMO SDAT.
Other values are available in the AMO but cannot be used for HFA IP
terminals.
2. Configuring SPE at the terminal

SPE settings are performed at the terminal either with DLS/WBM or via the
terminal itself. Signaling and display settings can also be performed at the
terminal.
OpenStage WBM
(Tab sheet) Administrator Pages > System > Security
A31003-H3160-S104-8-7620, 07/2014
Configuration
optiPoint WBM
It can be specified in this menu whether the transport mode TLS or TCP is
used. Additionally, it can be defined that the SPE certificate will be checked
by the CA certificate (check box Certificate check).
Admin > System > Signaling & Payload Encryption (SPE)
DLS
IP Devices > IP Phone Configuration > Signaling and Payload

Encryption (SPE)
A31003-H3160-S104-8-7620, 07/2014
Configuration
Detailed Information / Documentation
For more information please refer to the relevant documentation:

Deployment Service
http://apps.g-dms.com:8081/edoku/jsp/
searchresult_v2.jsp?edokutype=&search_mode=product&product=OpenSc
ape%20Deployment%20Service&product_version_main=&product_version
_sub=&search_term_type=all&term=&sort_result=title&docclass=&language
=de&checkdate=&solutions=false&lang=en
OpenStage HFA Terminals
• OpenStage HFA
http://apps.g-dms.com:8081/edoku/jsp/
searchresult_v2.jsp?edokutype=&search_mode=product&product=Ope
nStage%20HFA&product_version_main=&product_version_sub=&searc
h_term_type=all&term=&sort_result=product&docclass=&language=en&
checkdate=&lang=en
optiPoint 410
• optiPoint 410 advance

http://apps.g-dms.com:8081/techdoc/en/P31003H8400B413017619/
index.htm
• optiPoint 410 economy/standard

index.htm
• optiPoint 410 entry

index.htm
optiPoint 420 Operating Manual
• optiPoint 420 advance

index.htm
• optiPoint 420 economy/standard

index.htm
optiPoint 410/420 Administrator Manual
• optiPoint 410/420 Administrator Manual

http://apps.g-dms.com:8081/techdoc/en/P31003A2056B4150176A9/
index.htm
A31003-H3160-S104-8-7620, 07/2014
Configuration
3. Activating SPE
The configurations described above take effect if SPE is activated for this
system:
Parameters:
SPESUPP (YES/NO): Activates/Deactivates SPE for this system.

For more information please refer to Section 3.2, "CGWB SPE Activation /
Deactivation".
IMPORTANT: You must perform a hard restart on the system after you have
activated SPE. If you have a duplex system you have to perform the following
command on both processors simultaneously (at the same time). This means
all LTUs and APs will restart!
3.4.4 Signaling at the Display

A connection is displayed as "encrypted" if all sections (signaling & payload) and
the DMC path (signaling & payload) between all terminals involved in this call are
encrypted.
3.4.4.1 Display in Call State
If you want the terminal's display to indicate whether or not a call is encrypted,
you must first enable the parameter SECLVDSP in the AMO ZANDE for the entire
system.
CHANGE-ZANDE:TYPE=SECURITY,SECLVDSP=YES;
The SECLVDSP attribute must also be activated in AMO SDAT on the terminals
where the display is to appear.
CHA-SDAT:STNO=<station number>,TYPE=ATTRIBUTE,AATTR=SECLVDSP;
IMPORTANT: If you want a display to appear, the parameter SECLVDSP must

be activated in both AMO ZANDE and AMO SDAT. If the parameter is activated
for the first time in ZANDE, a RES-DSSU:PEN,… must be performed manually
for each subscriber (if parameter CONT is set to yes, the phone restart will be
executed automatically for each relevant subscriber).
You can use AMO SDAT, parameter AATTR=SECLVTON to ensure that the
secure station also receives an advisory tone if the call is not encrypted.
A31003-H3160-S104-8-7620, 07/2014
Configuration
CHANGE-SDAT:STNO=<station number>,TYPE=ATTRIBUTE,AATTR=SECLVTON;
3.4.4.2 Display in Idle State
The terminal's idle display does not indicate whether the station is secure or not.
Display via key

You can configure a key in AMO TAPRO to display the status of the station:
Example: CHANGE-TAPRO:STNO=<station number>,KY09=SECURE;
Please note that the first eight keys are preprogrammed in OpenStage terminals.
Display via SPE entry in menu

You can also check the security status of the terminal in idle call state using the
terminals menu.
• Voice encryption not enabled
– The subscriber is connected to the switch via TLS but SPE is not
activated for this terminal or
– The subscriber is connected to the switch via TCP. In this case terminal
configuration at the switch is not relevant.
In this case encryption is always disabled (Voice encryption not enabled).
• Voice encryption enabled

The subscriber is connected to the switch via TLS and the subscriber is
configured as a SECURE client.
In this case encryption is enabled (Voice encryption enabled).
• Voice encryption always active

configured as a CIPHER client.
– Logon via TCP not possible.
– All media streams are encrypted (at least to the gateway).

In this case encryption is always active (Voice encryption always active).
3.4.4.3 Scenarios
• Client A - Standard client

The subscriber is connected to the switch via TLS but SPE is not activated for
this terminal or the subscriber is connected to the switch via TCP (terminal
configuration at the switch is not relevant).
A31003-H3160-S104-8-7620, 07/2014
Configuration
• Client B - Secure client

configured in the system as a SECURE client.
• Client C - Cipher client

configured in the system as a CIPHER client.
Secure call: B calls C

Both subscribers have a secure connection to the gateway. Therefore the DMC
connection is also secure. The displays of both subscribers show encrypted call.
During the call both subscribers are able to check the security status in there
menus.
Non Secure Call: A calls B
The connection from A to the gateway is not secure. Only the connection from the
gateway to client B is secure. Therefore the DMC connection is not secure. The
displays of both subscribers show call not encrypted. During the call both
subscribers are able to check the security status in there menus.
Non Secure Call: A calls C

The connection from A to the gateway is not secure. Only the connection from the
gateway to client C is secure. Therefore the DMC connection if it is established is
not secure. The DMC connection ends in the HiPath 4000 because all
connections to client c (CIPHER) must be secure. The display of both subscribers
show call not encrypted. During the call both subscribers are able to check the
security status in their menus.
3.4.5 Deactivating SPE for Terminals

DLS/WBM can be used to deactivate SPE for all IP terminals (HFA terminals).
This causes all terminals to log off and then log on via TCP.
The /gateways themselves remain in secure mode, but no encryption methods

are used as long as all clients are connected via TCP.
CIPHER clients will not work correctly unless they are modified in AMO SDAT to
SECURE.
Activating SPE
As for deactivation, again using DLS/WBM.
A31003-H3160-S104-8-7620, 07/2014
Configuration
Activation / Deactivation of SPE for Access Points
Terminals will log off and log on when SPE is activated or deactivated.
IMPORTANT: The /gateways must already be in secure mode as otherwise the

clients are unable to log on.
3.5 Activation / Deactivation of SPE for Access Points

Activation
The following steps have to be performed for activating SPE for access points.
1. Distribute Master Encryption Key (MEK) via HiPath 4000 Assistant to all APs
configured in the system (states Ready, NPR (not present) and UNACH
(hierarchically blocked)).
This will
• configure the MEK in the RMX for all access points regardless of their
state and
• transmit the MEK to all access points in Ready state.

The Master Encryption Key (MEK) is used to encrypt the signaling data
between the host system and an IPDA access point.
The MEK must be configured first on the NCUI boards for new access points
and then on the host system. For more information, please refer to Section
3.5.1, “New Access Point in an Active SPE System”.
The MEK is configured via HiPath 4000 Assistant:
Expert Mode > Signaling & Payload Encryption > Administration
>Sections Configure Automatic MEK Distribution and Manual MEK
Distribution
A31003-H3160-S104-8-7620, 07/2014
Configuration
For more information on MEK administration, refer to the Administration

Manual "HiPath 4000 Assistant V6, MEK Administration" (http://apps.g-
dms.com:8081/techdoc/de/P31003H3460M1440100A9/index.htm)..
2. Check the log from the MEK client and see if any AP failed.
Expert Mode > Signaling & Payload Encryption > Administration >
Section MEK / Passphrase Distribution Log
3. For access points with the status NPR and UNACH, you need to enter the
MEK manually via CLI on the access point using the Set new MEK
XXXXXXXXXXXXXXXX command.
4. Once MEKs have been successfully configured for all access points, SPE
can be activated.
The access point encryption is activated with AMO SIPCO, parameter
IPDAENCR:
CHANGE-SIPCO:TYPE=SECURITY,IPDAENCR=YES;
IPDAENCR (YES/NO): Signaling and payload encryption for IPDA connections.

SPE activation for the access points fails if MEKs are not configured for all
access points (see points 1 to 3).
A31003-H3160-S104-8-7620, 07/2014
Configuration
5. Following activation of security in AMO SIPCO, a hard system restart is

required.
IMPORTANT: If you have a duplex system you have to perform the hard
restart command on both processors simultaneously (at the same time). This
means all LTUs and APs will restart!
Exception
A soft restart is enough, if
• no common gateways exist in the access point
• no HFA terminals exist in the access point
• only TDM terminals exist in the access point
• common gateways in the access point need no encryption
• HFA terminals in the access point need no encryption

Example: Soft restart of the active BP
EXEC-REST:TYPE=UNIT,UNIT=BP,RSLEVEL=SOFT ;
6. If you have common gateway boards and HFA terminals in the access point
and if these are to be used in secure mode, you have to perform all steps that
would be necessary if the common gateway board and the HFA terminals
were in the host system (activate SPE with AMO ZANDE parameter
SPESUPP, import certificates and so on).
Related topics:
• Trunk SPE Activation / Deactivation
• Terminal SPE Activation / Deactivation
• Distribution of Certificates to Gateways
• Distribution of Certificates with the WBM of the Gateway
• Distribution of Certificates to Terminals
Deactivation
If a customer would like to deactivate SPE completely for the access points and
the associated common gateways, a hard restart must be performed for this.
3.5.1 New Access Point in an Active SPE System

If you need to add a new access point while access point encryption is already
active, you need to do the following:
A31003-H3160-S104-8-7620, 07/2014
Configuration
• Configure the access point in the system as usual with AMO UCSU, AMO
APRT.
• Don't connect the access point yet because it will fail.
• Use SPE Administration in HiPath 4000 Assistant and update the board list
to see if your new access point has been added.
Section Manual MEK Distribution > Button Update board list
• Configure a MEK manually for this access point. This will transmit the
MEK to the RMX.
• Use the CLI to configure the same MEK on the NCUI.
• Now you can connect the access point to the LAN and activate the
connection to the system via EXEC-
USSU:MODE=CONFAP,LTU=<ltu_number>;.
A31003-H3160-S104-8-7620, 07/2014
Configuration
3.5.2 Deactivating SPE for Access Points with Soft

Restart
Access point encryption (signaling and payload) is deactivated with the AMO
SIPCO followed by a soft restart. In a duplex system, you also only have to
perform one soft restart on the active CC.
IMPORTANT: Deactivation of the access point encryption causes every call and
the associated DMC connections with access point reference (subscriber or trunk
in AP shelf) to be executed and signaled as non-secure calls from an end-to-end
perspective. The connections between the common gateway in the AP shelf and
the HFA terminals or the partner gateway, however, remain encrypted, i.e. TLS
terminals will still run on TLS in AP shelves and trunking gateways which have
already established a TLS connection will continue using TLS connections.
Activating SPE
Like deactivation, with the AMO SIPCO and soft restart.
Caution
AMO SIPCO prompts the administrator to perform a hard restart after activating/
deactivating SPE. This advisory is not modified for the following reasons:
• When SPE is already activated on the system for HFA terminals and IP
trunking and access point encryption is activated for the first time, a hard
restart must be performed before the feature works correctly.
• If a customer would like to deactivate SPE completely for an access point and
the associated common gateways, a hard restart must be performed for this.
A31003-H3160-S104-8-7620, 07/2014
Configuration
HiPath 4000 SoftGate SPE Activation / Deactivation
3.6 HiPath 4000 SoftGate SPE Activation / Deactivation
Figure 12 HiPath 4000 SoftGate and SPE - Overview
3.6.1 Features
• The signaling connection between HiPath 4000 SoftGate and common
control in host system is encrypted.
• Payload connections from HiPath 4000 SoftGate to HG 3570 in the host

system or to another HiPath 4000 SoftGate or to AP shelves are encrypted.
• As of HiPath 4000 V6, signaling and payload encryption is also supported for
SIP trunking and HFA subscribers.
• As of HiPath 4000 V6, Secure Trace is also supported for HiPath 4000
SoftGate (restrictions please refer to Section 3.6.2, “Restrictions”).
3.6.2 Restrictions
• If SPE is activated in the host system and no default MEK is assigned to the
HiPath 4000 SoftGate, the HiPath 4000 SoftGate will not start.
A31003-H3160-S104-8-7620, 07/2014
Configuration
• Signaling and payload encryption (SPE) is not supported for SIP subscribers.
• HFA signaling cannot be traced at the HiPath 4000 Softgate!
• vHG 3500 HFA, no CA certificate is needed on the board side. Only SPE
certificate is required. If DLS interrogates this vHG 3500, it gets no CA
certificate data.
3.6.3 Configuration
To use signaling and payload encryption (SPE) for HiPath 4000 SoftGate, the
Master Encryption Key (MEK) has to be configured as for a normal access point
(AP). For a normal access point, this is done with the Command Line Interface
(CLI). As the HiPath 4000 SoftGate does not have a CLI, the process is a little
different.
3.6.3.1 Scenario 1: Activate a HiPath 4000 SoftGate on a host

system that already has SPE activated
IMPORTANT: Please note the sequence!
IMPORTANT: Don't start the HiPath 4000 SoftGate because it will fail!
1. Use the SPE administration in HiPath 4000 Assistant and update the board
list to see your new HiPath 4000 SoftGate.
Section Manual MEK Distribution > Button Update board list
A31003-H3160-S104-8-7620, 07/2014
Configuration
2. Configure a MEK manually for this HiPath 4000 SoftGate. This will transmit
the MEK to the RMX.
Expert Mode > Signaling & Payload Encryption > Administration>
Sections Configure Automatic MEK Distribution and Manual MEK
Distribution
For more information on MEK administration, refer to the administration
manual "HiPath 4000 Assistant V6, Signaling & Payload Encryption" (http://
apps.g-dms.com:8081/techdoc/en/P31003H3460M1440176A9/index.htm).
3. Use the “HiPath 4000 Platform Administration (Portal)” to configure the MEK.
IMPORTANT: Since SPE is active in the system, the HiPath 4000 SofGate
will not be able to connect unless it has the correct MEK. WBM (for the distri--
bution of a MEK) can’t be used till the HiPath 4000 SofGate connects
successfully to the host system.
4. Now you can start up the HiPath 4000 SoftGate.
A31003-H3160-S104-8-7620, 07/2014
Configuration
3.6.3.2 Scenario 2: SPE is neither activated on HiPath 4000

SoftGate nor at host system
The following steps have to be performed for activating SPE for HiPath 4000
SoftGate.
IMPORTANT: Please note the sequence!
1. Please note the sequence! Switch on the host system and all HiPath 4000
SoftGates configured in the system.
2. Distribute Master Encryption Key (MEK) via HiPath 4000 Assistant to all
HiPath 4000 SoftGates. This will
This will
• configure the MEK in RMX for all HiPath 4000 SoftGates and
• transmit the MEK to all HiPath 4000 SoftGate.

The MEK must be set first on the vNCUI boards and then on the host system.
The MEK is configured via HiPath 4000 Assistant:
Expert Mode > Signaling & Payload Encryption > Administration
>Sections Configure Automatic MEK Distribution and Manual MEK
Distribution.
For more information on MEK administration, refer to the administration

manual "HiPath 4000 Assistant V6, Signaling & Payload Encryption" (http://
apps.g-dms.com:8081/techdoc/en/P31003H3460M1440176A9/index.htm).
A31003-H3160-S104-8-7620, 07/2014
Configuration
3. Check the log from the MEK client for any HiPath 4000 SoftGate errors.
Expert Mode > Signaling & Payload Encryption > Administration > MEK-
/ Passphrase Distribution Log
4. Once MEKs have been successfully configured for all HiPath 4000
SoftGates, SPE can be activated.
The IPDA encryption is activated with AMO SIPCO, parameter IPDAENCR:
CHANGE-SIPCO:TYPE=SECURITY,IPDAENCR=YES;
IPDAENCR (YES/NO): Signaling and payload encryption for IPDA connections.
IMPORTANT: SPE activation for HiPath 4000 Softgate fails when MEKs are
not configured for all HiPath 4000 Softgate (refer to point 1 to 3).
A31003-H3160-S104-8-7620, 07/2014
spe_04_secure_trace.fm
Secure Trace
Impact on the Service Contract
4 Secure Trace
Following an error, Secure Trace is used to let a service technician access
conventional analysis options even though SPE is active.
IMPORTANT: The right to evaluate trace information is reserved solely for

service personnel and is subject to customer approval.
4.1 Impact on the Service Contract

1. Gaining approval for activating Secure Trace
When using the secure trace function on secure connections, agreement
from the customer is necessary before starting the trace functionality. The
customer has to inform all involved parties about the "Secure Trace" function.
The customer must be informed that information in relation to a connection
even secure conversation data gained from a trace made to analyze a
problem in the framework of the end-to-end escalation process can be read.
All employees are obliged to protect any information acquired and to observe
the laws of privacy. This is set out in the company’s Data Privacy and Information
Security Policy. The private information obtained from the Secure Trace is only
used to limit / solve a problem. The information is deleted immediately
afterwards. The above note must be contained in all service and maintenance
contracts concluded with the customer.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Secure Trace Possibilities
WICHTIG: Note that the secure trace function uses a public/private key
mechanism, whereby the technician is able to capture the traces based on
the public key, but cannot decrypt them. In accordance with internal
processes and regulations, access to the private key for decryption purposes
is restricted to a clearly defined list of experts at the final support level.
2. Notification regarding activation of Secure Trace

Secure trace functionality is implemented on the basis of the safe deposit
principle. To make secure tracing possible, we need to unlock the mechanism
by means of two keys. One key is in the hand of the customer: s/he has to
enter a password to start secure tracing. The second key is the "Secure Trace
Certificate" issued by development. Secure tracing is only possible for a short
period of time if both conditions are fulfilled. If secure tracing is activated/
deactivated, an error message is sent to FA when HiPath 4000 is started/
stopped.
3. Trace data handling

The data obtained from secure tracing, together with the private key, is sent
to the GVS for further analysis.
4.2 Secure Trace Possibilities
Feature Signaling Payload

Native SIP Trunk x x
SIP-Q Trunk x x
HFA subscriber connected to HiPath - x
4000 SoftGate
IPDA x x
Table 4 Secure trace possibilities
4.3 Configuration
The company’s Security Office CA produces a new secure trace pair of keys
(public & private) every 15 days. These keys are valid for one month.
Public Key
The public key of this pair is published on the following intranet page in X509
certificate format.
https://hisat.global-intra.net/wiki/index.php/SecureTrace
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Configuration
This key (public key of the secure trace certificate) must be imported onto the
gateways in order to activate Secure Trace.
The Public Certificate of Security Office CA is included in the loadware. This
certificate is used to authenticate the secure trace public certificate imported onto
the board, i.e. verify that it is signed by the company’s Security Office.
Private Key
Apart from the secure trace public certificate / key the customer must set a
confidential password (Passphrase) when installing a system. This passphrase
is needed to activate Secure Trace.
IMPORTANT: If the passphrase is lost and Secure Trace has to be activated on

gateways, new system generation is mandatory in order to reset the passphrase
and set a new one. The old passphrase cannot be retrieved by any means from
the system if it is forgotten. Note also that the old passphrase is required in order
to change the passphrase. Generating the passphrase and keeping it secret is
the responsibility of the customer. This way the customer has full control of the
process of activating Secure Trace.
The passphrase is configured by HiPath 4000 Assistant:

Expert Mode > Signaling & Payload Encryption > Administration > Secure
Trace passphrase update
The old passphrase must always be entered and checked in order to generate a
new one. The checking of the old passphrase is skipped the first time a
passphrase is generated since no passphrase is stored in the DB as yet.
IMPORTANT: Nevertheless, a dummy passphrase must always be submitted.
The passphrase must be precisely 20 characters long, not less and not more.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Recording
If you have problems adding the passphrase please check if AMO CPTP contains
the following entry:
ADD-CPTP:APPL,,"DIAG_ADP","APPLPROC","MEK_APPL",YES,
102,102,"SRC_MEK","DST_MEK";
4.4 Recording
The following prerequisites must be satisfied to activate Secure Trace on a
gateway:
• You must have a valid secure trace certificate obtained as mentioned in

Section 4.1, “Impact on the Service Contract” above. The following checks
are carried out in the gateway when importing the secure trace public
certificate:
– signature check ok
– expiry date ok
– format in X509
• The passphrase set must be provided by the customer.
• SPE must be active on the target gateway.
• A duration for the Secure Trace must be submitted in the gateway, this
duration must not exceed the validity period of the secure trace public
certificate.
Example: If you are tracing the stream between two gateways and both are on
the same LAN switch, you shouldn't mirror both ports at the same time. This will
cause the stream between the two gateways to appear twice on the mirror port,
once from the transmitting port and once at the receiving end. It is enough to
mirror one port in this case, otherwise it will not be possible to decrypt the stream.
Example:
199 2009-05-24 289 198.16.16.160 198.16.16.170 SECTRC TraceBeaconTLS

10:42:10.657788
0.003777
200 2009-05-24 289 198.16.16.160 198.16.16.170 SECTRC TraceBeaconTLS
10:42:10.657813
0.000025
It is recommended to start recording the packages in Wireshark prior to activating

the Secure Trace. This ensures that all necessary information is available for
subsequent decryption of the traces.
The necessary TLS trace beacons must be available before the first messages to
be decrypted. A trace beacon is sent when the Secure Trace is activated. The
trace beacons are sent every minute afterwards.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Recording
Of course if this approach is not possible, you can start Wireshark at any
convenient point in time but please note that only the data exchanged after the
first appearance of trace beacons in the trace will be decrypted.
Trace beacons are transmitted every 60 seconds by the end points on which the
Secure Trace feature is active.
As mentioned above, when Secure Trace is activated or deactivated on an

endpoint, TLS session keys are renewed and this will ensure that traces can be
decrypted only when Secure Trace is activated but neither before nor after
because the keys before and after are different.
4.4.1 Loading a Secure Trace Certificate onto the

Gateway
The public secure trace certificate (see Section 4.1, “Impact on the Service
Contract”) is loaded via WBM.
Maintenance > Traces > Secure Trace > (right click) Import Certificates (PEM
or Binary Format)
The Load the Secure Trace Certificate via HTTP mask is displayed. Browse for
the .cer file. Press View Fingerprint of Certificate. Now import the certificate
with the Import Certificate from File button.
Figure 13 Loading the Secure Trace certificate
You must have a valid secure trace public certificate obtained as mentioned in
Section 4.1, “Impact on the Service Contract” above. The following checks are
carried out in the gateway when importing the secure trace public certificate:
– signature check ok
– expiry date ok
– format in X509
If the above checks are satisfied the certificate will be imported successfully.
4.4.2 Activating a Secure Trace

Secure trace beacons are inserted in the IP stream and are recorded with a
network trace tool (such as Wireshark). It is recommended to start the recording
prior to activation of the Secure Trace.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Recording
Maintenance > Traces > Secure Trace > Secure Trace Options > (right-click)
Start Secure Trace
The passphrase (Secure Trace Activation Passphrase - see Section 4.1, “Impact
on the Service Contract”) must be entered in this mask along with the trace duration
in minutes (Duration of Secure Trace (Mins)).
You can select the required trace content under Secure Trace protocols:
• CGW
• HFA endpoints:
– TC (TLS)
– H.323 Core/HSA (TLS)
• H.323 trunking signaling -> H.323 Core/HSA (TLS)
• IPDA signaling -> MMX (PEP)
• SIP trunking signaling -> SIP Core/SSA (TLS)
• Payload data (SRTP) -> MSC (SRTP)
• vHG 3500
• SIP trunking signaling -> SIP Core/SSA (TLS)
• Payload data (SRTP) -> MSC (SRTP)

Click Start Secure Trace to start Secure Trace. Trace activation tips:
Trace activation tips:

• If you are tracing H323 trunking message packets, it is enough to activate
Secure Trace on one side of the trunk call, i.e. on one of the two gateways.
• If you are tracing HFA message packets, it is only possible to decrypt data
exchanged between the phone and gateway, given that Secure Trace was
activated on the gateway. DMC payload between HFA phones cannot be
decrypted.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Recording
• If you are tracing NCUI message packets, Secure Trace must be activated on
each NCUI in order to be able to decrypt the signaling between NCUI and the
HiPath host system. Of course if the problem is the same on all NCUIs and the
problem can be reproduced, Secure Trace can of course only be activated on
one NCUI.
• If you are tracing SIP trunking HiPath 4000 – HiPath 4000 or HiPath 4000 –
OpenScape Voice message packets, it is enough to activate Secure Trace on
one side of the trunk call. In case the other side is an OpenScape Voice
system, Secure Trace should be activated on the HiPath 4000 side since
OpenScape Voice does not support the Secure Trace feature.
• For older loadware, Secure Trace should be activated on both sides of the
SIP trunk, i.e. on both gateways. If the HiPath 4000 loadware is older than
HiPath 4000 V6 and the partner is an OpenScape Voice system then it gets
more complicated. In this case please contact GVS to get detailed
instructions on how to proceed.
4.4.3 Secure Trace State

To determine the current status of a secure trace (activated or deactivated), select
Maintenance > Traces > Secure Trace > Secure Trace Options.
The Secure Trace State mask is displayed.
4.4.4 Secure TraceBeacons

Definition
Trace beacons are packets sent by a gateway on which Secure Trace has been
activated. Those packets contain the session keys used to encrypt the signaling
and payload. The session key included in the trace beacon is encrypted in turn
via the secure trace public key.
In order to decrypt those beacons and obtain the session keys you must have the
secure trace private key which is only available to Development and GVS.
Once you have the secure trace private key, you can decrypt the beacons and
retrieve the session keys which you can use to decrypt the signaling and payload
streams in the sniffer traces.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Recording
Secure Trace Beacon Types

TraceBeaconTLS - When Secure Trace HFA, SIPQ and H.323 are activated, the
TLS session key is renewed for all TLS connections and a trace beacon is
generated. Generation of trace beacons is performed every minute for all TLS
connections. Deactivating Secure Trace also stops generation of trace beacons
for all TLS connections and causes the TLS connection to renew session keys.
Example:
Source Src port Destinatio Dst port Protocol Info

n
20.1.1.1 65535 20.1.1.6 65535 SECTRC TraceBeaconTLS
TraceBeaconPEP – When Secure Trace is activated on NCUI boards, the MMX
component generates a TraceBeacon for the HSR connections (the signaling
connection between NCUI and CC). Afterwards it generates a TraceBeacon
every minute for the HSR connection. If a new HSR connection is set up or the
key material for an existing one is renewed, a TraceBeacon is generated and sent
out immediately. Deactivating Secure Trace also stops generation of
TraceBeacons for any HSR connection.
Note also that when Secure Trace is activated and before transmitting any
beacons, the existing PEP session key will be renewed and the new key
information will be sent encrypted in the first beacon.
When Secure Trace is deactivated, PEP session keys are renewed and beacons
are stopped.
Example:
Source Src port Destination Dst port Protocol Info

10.2.0.1 4000 10.1.0.1 1125 SECTRC TraceBeaconPEP
TraceBeaconSRTP – If Secure Trace is activated when an SRTP stream is set
up, the SRTP stack sends a TraceBeacon before the first payload packet. A
TraceBeacon is then generated every minute as long as the SRTP connection is
alive and Secure Trace is not switched off. Note that no TraceBeacons are
generated for SRTP streams already established when Secure Trace is activated.
The TraceBeacons are transported as normal RTP packets with the same IP and
port addresses as used by the SRTP stream itself but with a different payload
type (rtp.p_type==19).
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Verify Correct Activation of the Traces
4.5 Verify Correct Activation of the Traces

First you need to set up Wireshark as shown in the picture. Under Wireshark >
Preferences > Protocols > RTP the "Try to decode RTP outside of
conversation" option should be checked in order to see TraceBeaconSRTP.
IMPORTANT: If Try to decode RTP outside of conversation is not selected,

RTP trace beacons are not visible!
Activation of Secure Trace in systems on boards will generate TraceBeacons

(TLS/PEP/SRTP), which are visible (depending on the endpoint traced) in the
Wireshark with HiPath plug-in active.
By using a "SECTRC" display filter it is possible to see the TraceBeacons
exchanged between endpoints every minute. This can be checked using the
corresponding IP address if Secure Trace has been activated on the traced
endpoints.
TracebeaconSRTP can also be displayed by filtering the trace with
rtp.p_type==19. This filter does not require a HiPath plug-in.
The Secure Trace status on GWs can also be verified in the system via AMO
BCSU:
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
Decryption of Traces
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -10 - | READY
2 | Q2169-X STHC 1 A 0| | Q2169-X | 1 -14 - | READY
3 | Q2316-X STMI2 1 * A 0| | Q2316-X | 1 -07 - | READY
+--------------------------------+-+------------+------------+------------
| 1. FUNCT : HG3530 120 LINES B-CHANNELS : 60 BCHLCNT : 42
| SECURITY STATUS: 1:[X] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
+--------------------------------+-+------------+------------+------------
6 | Q2324-X NCUI4 1 0| | Q2324-X | 1 -05 - | READY
+--------------------------------+-+------------+------------+------------
| SECURITY STATUS: 1:[X] 2:[ ] 3:[ ] 4:[ ] 5:[ ] 6:[ ] 7:[ ] 8:[ ]
| (SEE BOTTOM) 9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
According to the legend which appears on the end of the display, this means here:
[ 1]: | SECURE TRACE ACTIVATED
4.6 Decryption of Traces

To read Secure Trace, you will need:
1. Wireshark HiPath plug-in (password protected):

http://czbrqh023x.global-ad.net/wiki/HiPath_plugin
2. Secure Trace "private key" file (.p12 file) available only for GVS and
Development.
3. Secure Trace "private key" password (.p12 file password) available only for
GVS and Development.
Configuring secure trace in Wireshark

Before you load the trace file, you must enter the Secure Trace "private key" file
(Certificate) and the Secure Trace "private key" password (Password) in
Wireshark under Edit > Preferences ... > Protocols > SECTRC.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
The signaling packets are automatically displayed in unencrypted format if all

previous steps were performed correctly.
IMPORTANT: If a connection is secure, its signaling / payload packages will not

be visible in Wireshark.
The tools required for decryption are only available to Development.
A31003-H3160-S104-8-7620, 07/2014
Secure Trace
A31003-H3160-S104-8-7620, 07/2014
spe_05_certificate_generation_assistant.fm
Generation SPE Certificates with HiPath 4000 Assistant
SPE Root Certificate
5 Generation SPE Certificates with HiPath 4000 Assistant

The SPE SSL Certificate Management area in HiPath 4000 Assistant comprises
the features for administering SSL security certificates for the feature Signaling
and Payload Encryption (SPE). It provides the tools for the generation of SSL root
certificate (CA) and for the generation of PKCS#12 certificate which is signed by
root certificate suitable for the SPE feature .
To start the application select in the HiPath 4000 Assistant Expert Mode >
Signaling & Payload Encryption.
5.1 SPE Root Certificate

This feature allows you to create your own root certificate which is used to sign
all SPE certificates generated by SPE Certificate feature and to download it
directly from the user interface.
The goal of this feature is to have all SPE certificates within a HiPath 4000
network signed by just one root certificate (CA).
A root certificate is a special type of self signed certificate.
The difference between self signed certificate and root certificate is that with self
signed certificates you need to specify the server name, whereas in the case of
the root certificate you need to specify a name for the root certificate (CA). The
name of the root certificate does not refer to a specific server.
5.1.1 Open the SPE Root Certificate Dialog

Navigate in the HiPath 4000 Assistant start page to Expert Mode > Signaling
and Payload Encryption > SPE Root Certificate. The SPE Root Certificate
dialog opens.
Two cases are possible:
• Root certificate does not exist yet.

If no root certificate has been created yet, the empty root certificate dialog will
open.
• Root certificate already exists.

If a root certificate has already been created on this server, the data of the
existing certificate will be displayed together with a corresponding note in the
root certificate dialog in the browser.
A31003-H3160-S104-8-7620, 07/2014
5.1.2 Creating a New Root Certificate

dialog opens.
There are two cases which have to be distinguished:
• No SPE root certificate exists

If no SPE root certificate is created yet, the dialog for creating a SPE root
certificate is displayed with empty fields.
Figure 14 SPE root certificate generation (no SPE root certificate exists)
• A SPE root certificate already exists
A31003-H3160-S104-8-7620, 07/2014
If a SPE root certificate is already created, click the New Root Certificate
button for creating a new SPE root certificate. A new dialog opens. The data
of the existing SPE root certificate are displayed in the entry fields and can
modified accordingly for the new SPE root certificate.
IMPORTANT: If you create a new SPE root certificate although a SPE root
certificate already exists for this server, the existing SPE root certificate will
be overwritten.
Figure 15 SPE root certificate generation with existing SPE root certificate
Procedure
1. Enter all required data. Mandatory fields are flagged with a red asterisk (*).
The following characters are not allowed in the entry fields: " & < > ÷ as well
as accented and special characters.
2. To get additional context information related to the individual entry fields, click
on the ? icon to the right of each entry field. The context-specific information
related to the respective field is displayed as a tooltip in the browser.
A31003-H3160-S104-8-7620, 07/2014
3. Click on Continue. The SPE root certificate will be generated. After the
creation of the certificate it is displayed and can be downloaded via a link.
5.1.3 Displaying/Downloading the newly Created SPE

Root Certificate
dialog opens.
If a SPE root certificate already exists it will be displayed and you may download
the SPE root certificate by clicking the SPE Root Certificate here link.
Figure 16 Download of SPE root certificate
A31003-H3160-S104-8-7620, 07/2014
SPE Certificate
5.2 SPE Certificate

The SPE Certificate feature provides the method of creating a new SSL
certificate and having it signed by SPE root certificate. Certificates created by this
function is always signed by SPE root certificate created in SPE Root Certificate
dialog (see Section 5.1, “SPE Root Certificate”).
5.2.1 Open the SPE Certificate Dialog

and Payload Encryption > SPE Certificate. The SPE Certificate dialog opens.
Three cases are possible:
• Certificate does not exist yet.

If no certificate has been created yet, the empty certificate dialog opens.
• Certificate already exists.

If a certificate has already been created in this server, the data of the existing
certificate will be displayed together with a corresponding note in the
certificate dialog in the browser.
• Root certificate does not exist yet.

If no root certificate has been created yet, user is informed to create root
certificate first
5.2.2 Creating a new SPE Certificate

There are two cases which have to be distinguished:
• No SPE certificate exists.

If no SPE certificate is created yet, the dialog for creating a SPE certificate is
displayed with empty fields.
A31003-H3160-S104-8-7620, 07/2014
SPE Certificate
Figure 17 SPE certificate generation (no SPE certificate exists)
• A SPE certificate already exists

If a SPE certificate is already created, click the New SPE Certificate button
for creating a new SPE certificate. A new dialog opens. The data of the
existing SPE certificate are displayed in the entry fields and can modified
accordingly for the new SPE certificate.
IMPORTANT: If you create a new SPE certificate although a SPE certificate

already exists for this server, the existing SPE certificate will be overwritten.
A31003-H3160-S104-8-7620, 07/2014
SPE Certificate
Figure 18 SPE certificate generation with existing SPE certificate
Procedure
1. Enter all required data. Mandatory fields are flagged with a red asterisk (*).
The following characters are not allowed in the entry fields: " & < > ÷ as well
as accented and special characters.
2. To get additional context information related to the individual entry fields, click
on the "?" icon to the right of each entry field. The context-specific information
related to the respective field is displayed as a tooltip in the browser.
3. Click on Continue. The SPE certificate will be generated. After the creation
of the certificate it is displayed and can be downloaded via a link.
A31003-H3160-S104-8-7620, 07/2014
SPE Certificate
5.2.3 Displaying/Downloading the newly created SPE

Certificate
If a SPE certificate already exists it will be displayed and you may download the
SPE certificate by clicking the SPE Certificate link.
Figure 19 Displaying/Downloading of SPE certificate
A31003-H3160-S104-8-7620, 07/2014
spe_06_certificate_dls.fm
Deployment Service (DLS)
Distribution of Certificates to Gateways
6 Deployment Service (DLS)
IMPORTANT: This chapter is only intended as a brief overview of the necessary

steps in the Deployment Service (DLS). For a detailed description, refer to the
appropriate DLS administrator manual.
6.1 Distribution of Certificates to Gateways
6.1.1 Creating a Virtual IP Device

IP Devices > IP Device Management > IP Device Configuration
Press button New to create a new virtual IP device.
In the general data area enter the Device ID (IP address of the gateway) and
select from the drop-down list IP Gateway as Device Family.
Choose now the tab DLS Connectivity.
In the section DLS Connectivity enter the DLS Server Address (IP address of
the DLS) and the DLS Port (18443).
These data must be the same as the data configured in the system.
A31003-H3160-S104-8-7620, 07/2014
Please make sure the DLS port and IP address are configured correctly in the
system:
CHANGE-ZANDE:TYPE=DLS,DLSIPADR=198.16.16.185,DLSPORT=18443;
Also make sure that AMO CGWB for the individual gateways is configured
correctly:
CHANGE-
CGWB:MTYPE=CGW,LTU=1,SLOT=4,TYPE=DLSDATA,DLSIPADR=198.16.16.185,
DLSPORT=18443;
In the section Security Settings the checkbox Secure mode required must be
activated. The Security Status is at the moment Standard.
In the drop down menu Pin Mode you can choose between different security
settings:
1. No PIN
Access data is sent unencrypted to the IP Device.
This mode can only be used if the parameter DLSACPAS = NO is set. Please
check with AMO CGWB and change it if necessary.
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=14,TYPE=DLSDATA,DLSACPAS=NO;
After saving the settings the Security State changes from Default to
Insecure.
A31003-H3160-S104-8-7620, 07/2014
2. Default PIN
Communication between DLS and the IP devices (gateways) is a secure TLS
connection using default certificates that are the same for every DLS and
gateway.
In order to make this TLS connection more secure we can additionally encrypt
the content of the TLS communication with a PIN.
Default PIN will use the same PIN for every gateway. You can view an already
randomly generated PIN in the Secure Mode tab under Administration >
Workpoint Interface Configuration and also generate a new random PIN.
A31003-H3160-S104-8-7620, 07/2014
After pressing the Save button you can see the default PIN.
3. Individual PIN
Individual PIN will use different PINs for every gateway.
DLS generates the PINs randomly and automatically when you press the
Save button.
A31003-H3160-S104-8-7620, 07/2014
6.1.2 Scanning the IP Devices (IP Gateways)

Bootstrapping: By scanning the IP devices (gateways), the DLS sends a
certificate to the gateway to prepare a secure connection for importing the
customer certificates (CA and certificate).
The scanning action is the same regardless of which mode is being used (No PIN,
Default PIN or Individual PIN).
There are 2 possibilities to do the SCAN.
1. Scanning individual gateways one by one
After pressing the Save button to save the configuration, you can press the
Scan button and the configured gateway will be scanned right away.
2. Group scanning of gateways in one run
After the scanning has been done, the next step will depend on the security
mode used:
A31003-H3160-S104-8-7620, 07/2014
a) When NO PIN mode is used, IP Device Configuration > DLS

Connectivity > Security State will show Secure. Now bootstrapping for
this mode is finished and you can proceed with the distribution of CA and
SPE certificates (see Section 6.1.3, “Distribution of the CA Certificate”
and Section 6.1.4, “Distribution of the SPE Certificate”).
b) When Default PIN or Individual PIN security mode is used, the Security
State Pending is shown after scanning.
The PIN must be entered on the gateway via CLI.

CLI command:
vxTarget> activate dls pin 29427922
activate dls pin - args: 29427922.
A31003-H3160-S104-8-7620, 07/2014
Bootstrapping succeeded.
OK
vxTarget>
IMPORTANT: There is no CLI with virtual gateways. The PIN must

therefore be entered in a WBM screen.
If you now go back to DLS DLS Connectivity > Security State, the
gateway will show Secure. Bootstrapping is now finished and you can
proceed with the distribution of CA and SPE certificates (see Section
6.1.3, “Distribution of the CA Certificate” and Section 6.1.4, “Distribution
of the SPE Certificate”).
Bootstrapping final verification in gateway WBM:

You can use the WBM application in HG 3500/3575 V4 to check if the
import operations worked properly and the certificates were activated.
Access is possible with the HiPath 4000 Assistant.
Menu: Menu: Expert Access > HiPath 4000 > HG35xx Web Based
Management
In the WBM you can view the certificates in the following directory:
Explorers > Security > Deployment and Licensing Client (DLSC)
There should be two entries:
• DLSC Client Certificate
• DLSC CA Certificate
A31003-H3160-S104-8-7620, 07/2014
6.1.3 Distribution of the CA Certificate
IMPORTANT: For vHG 3500 HFA, the CA certificate is not implemented on the
board as it is not necessary. Only SPE certificate is required.
Import CA certificate: IP Devices > IP Gateway Configuration >Signaling and

Payload Encryption (SPE)
All successfully bootstrapped boards (see Section 6.1.2, “Scanning the IP

Devices (IP Gateways)”) will be shown using the radio button Search.
Press the button Import Certificate.
A new window now appears where you can browse for the CA certificate. Up to
16 CA certificates can be imported. The importing and activation of CA
certificates can be combined in one step.
A31003-H3160-S104-8-7620, 07/2014
Select CA certificate
Confirm your selection.
Activate CA certificate.
Activate the checkbox Activate certificate and click Save to activate the
certificate. The status of the imported certificate will change from no active
certificate to equal if the certificate is valid. Additionally some data will be read
by the DLS, e.g. CN, OU.
A31003-H3160-S104-8-7620, 07/2014
6.1.4 Distribution of the SPE Certificate

Import SPE certificate: IP Devices > IP Gateway Configuration > VoIP Security
> tab Credentials
Browse for the certificate.
The importing and activation of the certificate can be combined in one step.
A31003-H3160-S104-8-7620, 07/2014
Select the certificate.
Passphrase is the password which is used to encrypt the content of the p12 file.
It is created when the p12 file was created.
IMPORTANT: Don't confuse this passphrase with the passphrase configured in

Assistant and used to activate Secure Trace. These two passphrases have
nothing to do with each other.
A31003-H3160-S104-8-7620, 07/2014
The certificate has been successfully imported.
Activate the certificate.
Certificate is active. Status (Status active/Import) is equal.
You can use the WBM application in HG 3500/3575 V4 to check if the import
operations worked properly and the certificates were activated. Access is
possible with the HiPath 4000 Assistant.
A31003-H3160-S104-8-7620, 07/2014
Menu: Menu: Expert Access > HiPath 4000 > HG35xx Web Based
Management
In the WBM you can view the certificates in the following directory:
Explorer > Security > Signaling and Payload Encryption (SPE)
There should be two entries:
• SPE Certificate
• SPE CA Certificate(s)
6.1.5 Resetting Bootstrapping

Should it happen that the DLS and the gateway can no longer communicate with
one another, the bootstrapping between the DLS and the gateway must be reset.
6.1.5.1 DLS Bootstrapping Reset
Reset button functionality:
If this checkbox is activated, the security mode can be reset to "Insecure" by

clicking Save.
The DLS must then send a new security configuration to the IP device, i.e. the
bootstrap operation must be repeated.
A31003-H3160-S104-8-7620, 07/2014
Distribution of Certificates to Terminals
6.1.5.2 Gateway Bootstrapping Reset
CLI command:
reset dls bootstrapping
IMPORTANT: There is no CLI with virtual gateways. Reset bootstrapping should

be performed in that case with WBM.
6.2 Distribution of Certificates to Terminals
6.2.1 Distribution of a CA Certificate (Terminals)

In the terminal the transport protocol can be set to TCP or TLS (via menu, WBM
of the terminal or DLS). If encryption is used the protocol TLS must be used for
the terminal.
An IP terminal only gets a CA certificate. The SPE certificate will be sent directly
from the gateway to the IP terminal, if the terminal is working with the TLS
protocol.
The CA certificate can be distributed to the phone only via the DLS. A manual
distribution as for the gateways is not possible.
Distribution of the certificate to the terminal via DLS.
A31003-H3160-S104-8-7620, 07/2014
IP Devices > IP Phone Configuration > Signaling and Payload Encryption

(SPE) > tab SPE CA Certificate
Select the CA certificate by using the button Import Certificate and Browse.
If the import of the certificate was successful a message is displayed.
A31003-H3160-S104-8-7620, 07/2014
Activation of the certificate.
If the activation was successful the status (Status Active/Import) will change
from no active certificate to equal.
A31003-H3160-S104-8-7620, 07/2014
6.2.2 Scanning the IP Devices (Terminals)

To add the IP Terminals in the DLS it is needed to scan the IP range from where
the terminals belong.
IP Device > IP Device Interaction > Scan IP Device
IP Ranges tab: Set name for the IP Scanner, IP address range (IP Address
from, IP Address to) and Port 8085.
A31003-H3160-S104-8-7620, 07/2014
Configuration tab: Set IP Address of DLS (DLS Address) and DLS Port and
select check box Send DLS Address. Start the scan with the button Scan IP
Devices.
Select Scan IP Devices, Register IP Devices and All IP Devices from Scan
and then select OK.
A31003-H3160-S104-8-7620, 07/2014
Scan Results tab: Number of detected gateways (IP Devices > Detected) will be
shown.
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
spe_07_certificate_wbm.fm
Distribution of Certificates with the WBM of the Gateway
Importing SPE CA Certificate for SIP Trunking
7 Distribution of Certificates with the WBM of the Gateway

This chapter is only intended as a brief overview of the necessary steps in WBM.
For a detailed description, refer to the administrator manual of the WBM.
• HG 3500
http://apps.g-dms.com:8081/techdoc/en/P31003H31
• vHG 3500 HFA (for HFA subscriber)

http://apps.g-dms.com:8081/techdoc/en/P31003H3160M1030176A9/
index.htm
• vHG 3500 SIP (for SIP trunking)

index.htm
• vHG 3575
index.htm
Certificates can be imported directly via WBM (Web-Based Management) of the

common gateway board if DLS is not available in the customer network.
You can access the WBM via HiPath 4000 Assistant: Expert Mode > HG35xx
Web Based Management.
7.1 Importing SPE CA Certificate for SIP Trunking

Explorer > Security > Signaling and Payload Encryption (SPE) > SPE CA
Certificate(s) > (right-click) Import trusted CA Certificate (PEM or Binary)
The Load a SPE CA Certificate via HTTP screen is displayed. Browse for the
certificate. Click View Fingerprint of Certificate. Now import the certificate with
the Import Certificate from File button.
An appropriate message is output if the import operation was successful.
A31003-H3160-S104-8-7620, 07/2014
Importing a SPE Certificate for SIP Trunking
Figure 20 Importing a SPE CA certificate for SIP trunking
7.2 Importing a SPE Certificate for SIP Trunking

Explorer > Security > Signaling and Payload Encryption (SPE) > SPE
Certificate(s) > (right-click) Import trusted SPE Certificate (PEM or PKCS#12)
The Load a SPE Key Certificate via HTPP screen is displayed. Enter the
passphrase ("confidential password" (see Section 4.3, “Configuration”)) and then
browse for the certificate. Click View Fingerprint of Certificate. Now import the
certificate with the Import Certificate from File button.
Figure 21 Importing a SPE certificate for SIP trunking
7.3 Importing a SPE Certificate for HFA Subscriber
IMPORTANT: Only possible for vHG 3500 HFA!
Configuration > SPE > Import Keycert
The Load a SPE Key Certificate via HTTP screen is displayed.
A31003-H3160-S104-8-7620, 07/2014
Certificates and Security on vHFA and WAN Interfaces
Figure 22 Importing a SPE certificate for HFA subscriber at vHG 3500
A SPE key certificate can be imported in this dialog by entering the decryption
password and the file name. The file containing the certificate originates in a
customer PKI certification authority (RA/CA) or the DLS server's internal
certification authority (CA) and must be available in PEM or PKCS#12 format.
7.4 Certificates and Security on vHFA and WAN Interfaces

vHFA
SPE certificate configured on vHFA WBM is used for TLS connection to its IP
address.
• TLS ports on vHFA are opened just if SPE is enabled and certificate is
configured (all on vHFA works as before WAN introducing)
• SPE certificate on vHFA is used just for "local" connection.
• SPE certificate on vHFA is not necessary if SPE is disabled or TLS is not

required for local connections.
WAN Interface
SPE certificate configured on HiPath 4000 SoftGate WBM is used for TLS
connection to WAN IP address.
• SRTP is always used on WAN regardless of security settings
• TLS ports on WAN are opened if certificate is configured regardless SPE is

enabled or disabled.
• WAN interface requires SPE certificate because only TLS is allowed on WAN.
• WAN interface always uses TLS and SRTP regardeless of SPE settings.
• If SPE is enabled the phone on WAN is reported to system as secure using

TLS.
• If SPE is disabled the phone on WAN is reported to system as unsecure using

TCP (regardless it uses TLS).
A31003-H3160-S104-8-7620, 07/2014
Certificates and Security on vHFA and WAN Interfaces
• If SPE is disabled then mobile HFA between WAN and local interfaces works
with TCP on local and TLS on WAN connections.
• if SPE is enabled and mobile HFA is required for some subscriber than this
subscriber have to use TLS also on local connection (otherwise mobile HFA
from WAN can not be cancelled on local phone because TCP can not
override TLS)
A31003-H3160-S104-8-7620, 07/2014
spe_10_autom_config.fm
AutoSPE Configuration
HiPath 4000
8 AutoSPE Configuration
IMPORTANT: This chapter is only intended as a brief overview of the necessary

steps in the Deployment Service (DLS). For a detailed description, refer to the
DLS Administrator Manual.
The area of automatic SPE configuration in DLS enables automatic configuration

of PKI-based Signaling and Payload Encryption (SPE) for users. This is
especially useful when there is no client PKI.
DLS supports the generation and deployment of SPE CA certificates (CA=

Certificate Authority) for administered IP devices (gateways and terminals).
When activating an SPE CA certificate, a SPE CA certificate is generated and
deployed for each administered gateway.
Via export and import, it is possible to migrate CA certificates from one DLS to
another.
With automatic SPE configuration via DLS, all terminals that are known in DLS
also receive the CA certificate (independently of the gateway) generated by the
AutoSPE configuration. The validity of this certificate can be checked in the
terminal's security settings (DLS: HFA Server Validation, Phone: Certificate
Check).
8.1 HiPath 4000

Requirements for SPE
IMPORTANT: SPE certificates can be configured at the gateways even if SPE is

deactivated.
1. An NTP server must be configured for time synchronization.
2. The following must be set in AMO ZANDE SPESUPP=YES:

EX-REST:TYPE=UNIT,UNIT=BP,RSLEVEL=HARD;
3. The parameter CLASSEC=SECURE must be set in AMO SDAT for each SPE
subscriber:
CHANGE-SDAT:TYPE=DATA1,CLASSEC=SECURE;
4. You have to check in AMO CGWB for HFA stations if the value in the
parameter branch TYP=GLOBIF is TLSP=4061.
A31003-H3160-S104-8-7620, 07/2014
8.2 Deployment Service (DLS)
8.2.1 DLS Time Server

For example: Freeware tool "Nettime"
IMPORTANT: The Windows Time Service must be ended.
8.2.2 Preparing DLS
Figure 23 Creating a Virtual Device / IP Gateway
Figure 24 Scanning an IP Gateway
A31003-H3160-S104-8-7620, 07/2014
Device Configuration
Figure 25 IP Gateway "scanned"
8.3 Device Configuration
8.3.1 Preparations
IMPORTANT: The value for H.225.0 TLS must be 1300.
Figure 26 Preparing Devices
The display and trace time can be set to "SNTP".
A31003-H3160-S104-8-7620, 07/2014
Automatic Certificate Creation
8.3.2 Time Server
Figure 27 Time Server Devices
8.4 Automatic Certificate Creation
Figure 28 Issuer: Administration
Figure 29 Issuer: Administration > Settings
A31003-H3160-S104-8-7620, 07/2014
Activate Voice Encryption
Figure 30 CA Administration
In the case of CA administration, a certificate must first be created, then

distributed, and finally activated. This can be displayed in the status.
The lower table shows how many terminals have received certificates.
8.5 Activate Voice Encryption

To activate voice encryption from SPE, the transport protocol must be switched
to "TLS":
Figure 31 Activate Voice Encryption
8.6 Check Certificates

Display the current certificate on the terminal: SPE CA certificate(s)
A31003-H3160-S104-8-7620, 07/2014
Checking SPE
Display the current certificate on the gateway: SPE CA certificate(s)
IMPORTANT: Both certificates must always be identical.
8.7 Checking SPE

A key can be configured on the HFA terminal to display the SPE status.
8.8 Adding new Gateways after AutoSPE Activation

The board has to be added in DLS as a virtual device, bootstrapped and scanned
as explained in Chapter 6, “Distribution of Certificates to Gateways”).
You will then be able to see the board in the board list under AutoSPE
configuration, also under IP Devices > IP Gateway Configuration > Signaling
and Payload Encryption (SPE).
In order to send the already generated AutoSPE CA and SPE certificates to the
new gateway, you have to go to IP Devices > IP Gateway Configuration >
Signaling and Payload Encryption (SPE). From there you can manually import
the certificates onto the new gateway.
A31003-H3160-S104-8-7620, 07/2014
Adding new Gateways after AutoSPE Activation
A31003-H3160-S104-8-7620, 07/2014
Adding new Gateways after AutoSPE Activation
A31003-H3160-S104-8-7620, 07/2014
dmc_01_feature_description.fm
Feature Description
Payload Switching DMC
To support the Payload Switching feature, the Direct Media Connection DMC
feature is used for Voice over IP (VoIP) connections in HiPath 4000.
Direct Media Connections DMC can be described and defined in the following
way:
The payload (voice channel) of a HiPath 4000 internal or networkwide voice
connection will be exchanged within a LAN in which a direct IP connection is
possible without conversion into a TDM data stream.
By the use of the feature "DMC Any-to-any" payload data is transported within a
HiPath 4000 network directly between the IP Endpoints without several IP-TDM
conversions of the payload. This direct payload connection is called Direct Media
Connection (DMC).
DMC has two purposes:
• Avoid degradation of speech quality by minimizing the number of IP/TDM

hops/conversions.
• Optimize the bandwidth: for those cases activation of VAD is very important.
A31003-H3160-S104-8-7620, 07/2014
dmc_01_feature_description.fm
Feature Description
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Direct Media Connect (DMC) in Connection with HFA Subscriber
Feature Description
2 Direct Media Connect (DMC) in Connection with HFA

Subscriber
2.1.1 Motivation
If two HFA IP phones are connected in a two-party call without the Direct Media
Connection DMC feature, a double IP/TDM conversion of the payload would be
performed. This causes a loss of quality of the voice transmission which results
from the multiple conversion of the payload between IP and TDM and vice versa
(status of HiPath 4000 V1.0). To avoid this loss of quality the IP payload is
exchanged directly between the two subscribers if both are in a two party
connection.
IP Endpoints can be:
• HFA IP phones
• IP Trunking Gateways (z.B.: HG 3500)
• IPDA boards (z.B.: HG 3500)
The IP endpoints can be the real endpoints of the connection (i.e. there is a
Master Connection between two IP phones) or the IP endpoints are only
endpoints of a section within the Master Connection. E.g. an anate or digite may
also profit from a DMC if it is connected to its partner via IPDA Access Point or IP
Trunking Gateway.
The setup of a call is done within several steps.
Steps 1 and 2 are the normal call setup procedures as known in HiPath 4000
V1.0. The result is called Master Connection. The normal call setup procedure is
extended by steps 3 and 4 to build the optional Direct Media connection.
1. In a first step, a signaling connection between the users is established.
2. Parallel to that signaling connection a so called Master Connection (MC) for

the payload is established. The payload path of the Master Connection may
be segmented into TDM and IP paths:
• within a TDM network this is a specific B channel
• within an IP network, this is a RTP connection.

The RTP payload connection is established and controlled by H.323
procedures (in particular by the use of the fast connect procedure).
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
3. After the Master Connection between the users is established and connected,
i.e. both users are in the talk state, a DMC connection between the IP
endpoints of the Master Connection can be established. The called IP
endpoint initiates the setup of the DMC connection.
4. When the DMC connection is established, the payload is transported using

this H.323 connection. However, the Master Connection exists in parallel, but
without conveying payload as long as the DMC connection exists (the Master
Connection is on a "stand-by" mode).
If the talk-state is released (e.g. for the setup of a consultation call) the IP
endpoint switchs back immediately to the Master Connection and releases
the DMC connection.
2.1.2 Notes concerning Direct Media Connections

DMC
• The Direct Media Connection will be switched in the two-party call state, that
means in the basic call and the simple consultation call. A DMC will also
be switched if the call is set up via a feature like call forwarding or picking up
a group call or if a secondary line answers a keyset call. A DMC is also
switched for conference calls.
• If the involved parties aren‘t in a two party connection the IP/TDM conversion
and the switching via the TDM switching network (MTS) is executed.
• If a Direct Media Connection is established the connection path via the MTS
switching network for multiple IP/TDM conversion (Master Connection) has to
stay switched in parallel to the direct IP connection so that immediately after
termination of the two party call state the MTS with its capabilities for tones
and conferenceing is available for any feature control by call processing.
• DMCs are established also for Fax/Modem connections.
2.1.3 Bandwidth Considerations
2.1.3.1 General Notes
While a DMC is active only SID (Silence Insertion Descriptor)/CN (Comfort Noise)
frames are sent on the master connection if involved components are configured
with VAD (see Section 2.3.3, “Voice Activity Detection (VAD)”). Therefore this
master connection needs only a reduced bandwidth.
You can find the tables for bandwidth in the document “Gateways HG 35000 and
HG 3575”, Section 3.5.4, “Required Bandwidth per Connection”.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
For additional information about bandwidth administration please refer to the

Resource Manager and AMO GKTOP.
By inserting SID/CN, analog background noise is simulated digitally during

silence to assure the listener that the link is active and operational. The
background noise RTP packets with CN flag are sent on the master or slave
connection once per second.
2.1.3.2 Gateways
Only DMC endpoints are aware of the DMC and able to reduce bandwidth on the
Master connection accordingly.
If the gateway is not a DMC endpoint e.g. in multihop scenarios, then the gateway
is NOT aware of the DMC. In order to reduce bandwidth usage the gateways
should be configured with a codec supporting VAD and additionally VAD must be
activated (VAD will then lead to the gateway generating CN packets).
IMPORTANT: HG 3530 is never a DMC endpoint.
These are recommended ASC settings in AMO CGWB:
PRIO1: CODEC = G711A VAD = YES RTP-SIZE = 30

PRIO2: CODEC = G729AB VAD = YES RTP-SIZE = 20
PRIO3: CODEC = G723 VAD = YES RTP-SIZE = 30
PRIO4: CODEC = NONE VAD = NO RTP-SIZE = 20
PRIO7: CODEC = G729A VAD = NO RTP-SIZE = 20**
Table 1 Recommended ASC settings in AMO CGWB

** This setting should be removed if bandwidth reduction is always wanted.
However in this case silent suppression (VAD) must be activated in the phone as
described under Section 2.3.3, “Voice Activity Detection (VAD)”, because there’s
need of:
• G729AB: VAD=YES in AMO CGWB if we check silent suppression checkbox

in phones
or
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
• G729A: VAD=NO in AMO CGWB if we don’t check silent suppression

checkbox in phones
NOTE: If set only G729AB VAD=YES in AMO CGWB and silent suppression
checkbox in phones is not checked, then every call attempt fails and HY2 code
(no Bearer Capabilities) will be displayed.
2.1.3.3 HFA
optiPoint phones generate CN frames on the master connection once DMC is

established.
OpenStage phones do not generate CN on master connection once DMC is

established.
VAD setting in AMO SDAT controls the sending CN for normal connections and
DMC slave connections.
The phone’s DSP (Digital Signal Processor) will accept VAD for G711, G729 or
G723 regardless of the phone VAD SDAT setting. VAD is not defined for G722.
Codecs and silent suppression

• G711 - High quality codec, capable of Voice Activity Detection (VAD) and
Comfort Noise Generation (CN);
• G723.1 - Audio codec for voice that compresses voice audio in 30 ms frames;
Capable of silent suppression (VAD) and comfort noise (CN);
Not reliable for transporting music or tones such as DTMF or fax.
• G729 - Voice compression codec; Not capable of silent suppression (VAD)

- implicitly silence suppression is off
• G729A - Voice compression codec; Not capable of silent suppression (VAD)

- implicitly silence suppression is off
• G729B - Voice compression codec; Capable of silent suppression (VAD); not

compatible with G729 or G729A
• G729AB - Voice compression codec; Capable of silent suppression (VAD);

only compatible with G729B
2.1.4 Scenarios
The following scenarios are being considered:
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
Scenario A: Direct Media Connection DMC within a single HiPath 4000

node.
Scenario B: Direct Media Connection DMC between HFA IP phones within a

HiPath 4000 network.
This scenario B is supported in HiPath 4000 in conjunction with the IP Gateway

HG 3500 V4.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
Scenario C: Direct Media Connections DMC between HFA IP phone and

IPDA shelf within a single HiPath 4000 node.
Scenario D: Direct Media Connections DMC between netwide IPDA-shelves.
DMC in mixed scenarios

In mixed scenarios the DMC is executed in the 2 party call state between the first
possible IP address at the A-side (IP phone or HG 3575 or HG 3500
(FUNCTION=HG3570) or HG 3500 (FUNCTION=HG3550)) and the last possible
IP address at the B-side (i.e. again HG 3500 (FUNCTION=HG3550) or HG 3500
(FUNCTION=HG3570) or HG 3575 or IP phone).
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
2.1.5 Domain concept

In very large enterprise networks it may be necessary to subdivide the network
into several socalled domains. Depending on the configuration DMC connections
may be allowed only within these domains or end-to-end over several domains.
Example 1: DMC possible from domain A until domain B:
Note: for this scenario no special configuration is needed (default)
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
Example 2: DMC not possible from domain A to domain B, DMC only

possible within domains A and B:
In this case both ends of the link between the domains have to be marked as
domain end.
This is done with an attribute within LCR (see chapter Generation). This attribute
has to be set in domain I for the LCR route leading to domain II, and in domain II
for the LCR route leading to domain I.
2.1.6 DMC Interworking to HiPath 3000

Supported scenarios:
Scenario 1: HG 3500 terminates the HiPath 3000 payload switching
This scenario applies to two cases:
– the endpoint in the HiPath 4000 network is a TDM device or
– DMC interworking between HiPath 4000 and HiPath 3000 is not allowed
(this scenario can be achieved by setting the LCR domain end attribute in
the HiPath 4000 for the route leading to the HiPath 3000 network).
In the first case the end-to-end connection consists of a TDM connection on the
HiPath 4000 side and an IP connection between the HG 3500 and the IP endpoint
on the HiPath 3000 side.
In the second case the connection between the endpoint in the HiPath 4000
network and the endpoint in the HiPath 3000 network consists of
• a DMC part in the HiPath 4000 network and
• Payload Switching (PLS) in the HiPath 3000 network, i.e. the PLS is
terminated by the HG 3500 on the HiPath 4000 side.
This second case is shown in the following picture:
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
• DMC within HiPath 4000 network: 

From the 1st possible A-side IP adress to 1st possible B-side IP adress.
Signaling of A- and B-IP address takes place via CorNet-NQ (SETUP/
CONNECT-messages)
• PLS (Payload Switching) within HiPath 3000 network: 

The IP-Gateway HG 3500 serves as Payload Switching HFA Proxy of HiPath
3000.
Scenario 2: HG 1500 terminates HiPath 4000 Direct-Media-Connection
DMC to HG1500 in HiPath 3000
When interworking between HiPath 4000 and HiPath 3000 is allowed and the
endpoint in the HiPath 3000 network is a TDM device the HG1500 terminates the
DMC.
RTP stream between the HiPath 3000 HG1500 and the HiPath 4000 HG 3500
belongs to the master-connection.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Feature Description
Scenario 3: Direct-Media-Connection between HFA IP phones end-to-end
DMC to HFA Phone in HiPath 3000
When interworking between HiPath 4000 and HiPath 3000 is allowed and the
endpoint in the HiPath 3000 network is a HFA phone a DMC can be established
end-to-end.
RTP stream between the HiPath 3000 HFA phone and HG 3500 belongs to the
master-connection.
Scenario 4: HiPath 4000 as transit node between two HiPath 3000 nodes
In this case, no end-to-end DMC connection can be set up between the HiPath
3000 IP devices (IP phones or HG1500). On the A side, a DMC is established to
the most distant HiPath 4000 DMC endpoint (HG 3500 (FUNCTION=HG3550 or
HG3570) or HG3575). This DMC overlies a HiPath 3000 PLS connection (not
depicted in the figure) and the IP parts of the HiPath 4000 network.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Service Information
If the HiPath 4000 network has no IP parts, the DMC connection is omitted and
the payload is transmitted on the PLS connection. This applies if, instead of a
HiPath 4000 network or an IPDA configuration, an individual HiPath 4000
connected on both sides with HiPath 3000 systems or networks is involved. So a
DMC connection on the A side only exists if an optimization is necessary.
On the B side, a payload switching connection is established.
So it always involves a connection with 2 IP hops.
2.2.1 Features with DMC

The following list shows for which features a DMC is established:
• Basic call
• Basic call with reroute internal
• Basic call with rerouting (NW)
• Consultation call (including toggle, end of consultation (back to held party))
• Transfer talking with or without Path Replacement
• Transfer ringing with or without Path Replacement
• Immediate recall
• Centralized attendant transfer
• CFU, CFNR with forwardswitching or with rerouting or mixed (rerouting in

transit switch)
• Call back (message waiting, busy, no reply)
• Pickup of a call in a pickup group
• Directed call pickup
• Call to Hunt group
• Application establishes call (ACL make call)
• ACD call
• Reduction of conference to 2-party call
• Call to Keyset (secondary line answers the call)
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Generation
• executive/secretary (CHESE) (secretary answers the call)
2.2.2 Feature activation while DMC is active

When a DMC is active for a two party call and a feature is being activated the
DMC is released and the call is switched back to the master connection.
This applies for features that are activated by one of the involved parties and also
for features activated by a third party (e.g. campon, override).
When the feature is finished and the call returns to the normal two party talk state
the DMC is not reactivated except for the features that are listed in the chapter
above.
Feature response in exception situations:

• DTMF Handling
A DMC is released if the endpoint requests the sending of DTMF via SIU
(signaling unit). E.g. a HFA phone requests the sending of DTMF via access
code.
• DTMF transmission over DMC

DTMF tones are recognized in DMCs and transmitted, e.g. if the tone is
received by the HiPath 4000 system at a CO interface or a DTMF enabled
anate sends DTMF by itself.
2.3 Generation
2.3.1 DMC Authorization

Possible IP endpoints have to be allowed to switch a DMC.This is done with the
following AMO commands:
• IP phones:
CHANGE-SDAT:STNO=<extension
number>,TYPE=ATTRIBUT,AATTR=DMCALLWD;
• NCUI:
CHANGE-STMIB:MTYPE=NCUI2,LTU=xx,TYPE=DMCDATA,DMCALLWD=YES;
• STMI pool for IPDA:
CHANGE-SIPCO:TYPE=DMCDATA,DMCALLWD=YES;
• IP trunking:
CHANGE-TDCSU:PEN=<ltg-ltu-slot-cct),DEV=HG3550IP,DMCALLWD=Y;
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Generation
2.3.2 Maximum number of DMC connections on IP

boards
Please refer to „Gateways HG 35000 and HG 3575“, Section 3.6, “B Channels”.
AMO commands:
• NCUI:
CHANGE-STMIB:MTYPE=NCUI2,LTU=xx,TYPE=DMCDATA,DMCCONN=<number
of allowed DMC connections>;
• STMI - IP trunking:
CHANGE-CGWB:MTYPE=CGW,LTU=xx,TYPE=DMCDATA,DMCCONN=<number of
allowed DMC connections>;
2.3.3 Voice Activity Detection (VAD)

In order to save bandwidth Voice Activity Detection (VAD) has to be activated for
IP connections. When a DMC is established and VAD is set only idle frames are
sent on the master connection.
VAD is activated with the following AMO commands:
• Station:
CHANGE-SDAT:STNO=<ext.
number>,TYPE=DATA1,CLASSMRK=VAD&EC&G711&G729OPT;
• Digital trunks:
CHANGE-TDCSU:PEN=<ltg-ltu-slot-
cct),CLASSMRK=VAD&EC&G711&G729OPT;
• Analog trunks:
CHANGE-TACSU:PEN=<ltg-ltu-slot-
cct),CLASSMRK=VAD&EC&G711&G729OPT;
• IP trunking:
Modifying of codecs and VAD is no longer possible via WBM and any change
has to be done via AMO CGWB. However, it is still possible to display the
current settings via WBM under Explorers > Voice Gateway > Codec
Parameters
(The same applies for HG 3575 IPDA - AMO STMIB)
• HFA: VAD must be activated at both ends of the HFA master connection.
For IP phones: the silence suppression needs to be checked in WBM of the
phone under Administrator > Speech/Cloud > Codec Preferences.
For HG 3500:
CHANGE-CGWB:MTYPE=CGW,LTU=x,SLOT=xx,TYPE=ASC,VAD=YES;
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Generation
2.3.4 Domains
It may be necessary to subdivide a very large enterprise network into several
areas (domains) where DMC is only possible within a domain and not between
domains.
In order to achieve this an LCR mark has to be set at each domain end. When
this mark is set DMCs are not established beyond this point.
AMO command:
CHANGE-LDAT:LROUTE=<route number>,LATTR=<existing
attributes>&DMCEND;
2.3.5 H.323 stack on IPDA boards

The H.323 stack on IPDA boards has to be configured using the following AMO
commands:
• NCUI:
CHANGE-STMIB:MTYPE=NCUI2,TYPE=H323,GWNAME=<string>;
• STMI:
These settings are not possible via AMO. Please use WBM of the board.
For the correct numerical values please refer to the configuration manual for
IPDA boards.
In addition, the codecs used for the DMC must be configured (Master Connection
codecs see AMO SDAT / AMO TACSU / AMO TDCSU).
• NCUI:
CHANGE-
STMIB:MTYPE=NCUI2,LTU=xx,TYPE=ASC,PRIO=PRIO1,CODEC=G729;
CHANGE-
STMIB:MTYPE=NCUI2,LTU=xx,TYPE=ASC,PRIO=PRIO2,CODEC=G711;
• STMI:
CHANGE-
CGWB:MTYPE=CGW,LTU=xx,SLOT=xx,TYPE=ASC,PRIO=PRIO1,CODEC=G729;
CHANGE-
CGWB:MTYPE=CGW,LTU=xx,SLOT=xx,TYPE=ASC,PRIO=PRIO2,CODEC=G711;
WBM > Explorers > Voice Gateway > Codec Parameters
2.3.6 Troubleshooting Hints

If you encounter problems with DMC please check first the activation switches in
Section 2.3.1, “DMC Authorization”.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Generation
Another switch to be checked is the diagnosis switch 08 in CP2 branch of AMO

DIAGS.
DISPLAY-DIAGS:COMP=CP2;
Please remember that switch S08=ON means DMC is deactivated in the whole
system, so the switch should be usually set to OFF in order to have DMC enabled.
Then please assure that DMC configured resources for the involved boards are
not equal 0 or too few (see Section 2.3.2, “Maximum number of DMC connections
on IP boards”). Check also if resource manager is configured/involved.
Further you can check if the components are not part of different domains and
inter-domains DMC is allowed or not.
Supported features table should also be checked (see Section 2.2, “Service
Information”).
The DMC connections can be checked by activating DIAGS switch 09 in CP2.

DMC connection related information would be visible then in HISTA under :
F4066 M8 N4058 NO ACT BPA CP ADVISORY
ALARM CLASS:CENTRAL:023
FORMAT:49
DMC
The flow which grants a successful DMC is:
At B party: STATE_NEW = init; event = ACT_PROXY_DMC_START

At A party: STATE_NEW = active; event = UP DMC_IND OK
At B party: STATE_NEW = active; event = UP DMC_CONF
WBM of IPDA/gateway boards could also be checked under Explorers' Statistics,

for some DMC related calls.
Usefull may be display of AMO ZAUSL.The result shows counters of DMC

connections:
|N0059: NUM. OF ALL SUCCESS. DMC ATTEMPTS (ACT. OR PAS).. 0|
|N0060: NUM. OF ALL UNSUCCES. DMC ATTEMPTS(ACT. OR PAS). 0|
|N0061: NUM. OF SUCCESSFUL DMC ATTEMPTS, BOTH PROX. INTR. 0|
|N0062: NUM. OF UNSUCCESSFUL DMC, BOTH PROXIES INTERNAL.. 0|
|N0063: NUM. OF ALL UNSUCCES. DMC ATTEMPTS(INSTANT DMC). 0|
With G711, the CN RTP packages are displayed in wireshark as Payload Type
:Comfort Noise.
With G729 they appears as: Payload Type :ITU-T G729 (no difference to the
normal RTP) but the length of payload is usually only 2 bytes long and total
package length is 60 bytes.
With G723.1 the CN is recognized in the field: frame size and codec type :SID
frame.
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Relevant AMOs
2.4 Relevant AMOs

Language
CGWB MTYP=CGW d Konfiguration von HG 3500
MTYPE=CGW e Configuration of HG 3500
TYP=DMCDATA d DMC-spezifische Daten konfigurieren
TYPE=DMCDATA e Configure DMC specific data
DMCCONN d Anzahl der DMC-Verbindungen
DMCCONN e Number of DMC connections
TYP=ASC,VAD=J/N d VAD in Senderichtung erlaubt / nicht
erlaubt,Wert=JA / NEIN
TYPE=ASC,VAD=Y/N e VAD enabled / not enabled in send
direction, value = YES / NO
LDAT LATTR d LCR Attribut,
neuer Wert: DMCENDE = Ende der
DMC Domaine
LATTR e LCR attribute,
new value: DMCEND = end of DMC
domain
SDAT EMERK & AMERK d Teilnehmermerkmal,
Wert: DMCERL = DMC erlaubt
AATTR & DATTR e subscriber attribute,
value: DMCALLWD = DMC allowed
CLASSMRK d Classmark, Wert VAD = Voice Activity
Detection
CLASSMRK e Classmark, value VAD = Voice Activity
Detection
SIPCO TYP d Datentyp (Verzweigungsparameter),
Wert: DMCDATA
TYPE e type of data (branching parameter),
value: DMCDATA
DMCERL d DMC erlaubt, Wert = JA/NEIN
DMCALLWD e DMC allowed, value = YES/NO
STMIB MTYP=NCUI2 d Konfiguration der HG 3575
MTYPE=NCUI2 e Configuration of HG 3575
TYP=DMCDATA d DMC-spezifische Daten konfigurieren
TYPE=DMCDATA e Configure DMC specific data
DMCCONN d Anzahl der DMC-Verbindungen
DMCCONN e Number of DMC connections
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Relevant AMOs

Language
TDCSU GER=HG3550IP d Integriertes IP-Gateway HG 3500
DEV=HG3550IP e Integrated IP Gateway HG 3500
CLASSMRK d Classmarks für IP Verbindungen, Wert
VAD = Voice Activity Detection
CLASSMRK e classmarks for IP connections, value
TACSU CLASSMRK d Classmarks für IP Verbindungen, Wert
CLASSMRK e classmarks for IP connections, value
A31003-H3160-S104-8-7620, 07/2014
dmc_02_h323.fm
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Direct Media Connect (DMC) in Connection with SIP Subscriber
Feature Description
3 Direct Media Connect (DMC) in Connection with SIP

Subscriber

One major function on the LAN side is “direct payload” (DMC -> Direct Media
Connect) between the call parties. This function can be activated/deactivated for
all SIP endpoints.
Given the fact that direct payload transmission between SIP subscribers and
other IP devices and gateways is desirable (due to better voice quality), despite
the fact that SIP subscribers do not support the H.323-based DMC procedure,
HG 3500 has been extended with HiPath 4000 V3.0 to include a “DMC proxy”.
This feature is also included in the common gateway board. In other words, as far
as DMC signaling is concerned, the gateway functions on behalf of the SIP
subscriber and converts the DMC signaling into SIP signaling.
For HFA subscribers the DMC connection is shown in the following diagram.
Anate/TDM phone
HG 3500
HFA HG 3500 HG 3500
H323 IP trunkg
HFA Subscriber Slave Signaling Master Signaling

Slave Payload Master Payload
Figure 1 DMC in connection with HFA subscriber
This figure shows the situation for an HFA subscriber calling a TDM subscriber in
another node via an H323 IP trunk. The master connection for both signaling and
payload is maintained via the HG 3500 (in this case configured as a HFA
gateway) and both HG 3500 (IP trunking) gateways. The Slave connections are
the DMC conections and these are between IP endpoints, on the one side the
HFA subscriber and on the other side the HG 3500 IP trunking board.
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Feature Description
The transport addresses (IP addresses/ports) for payload transmission are

transmitted as part of the DMC signaling. The DMC proxy does not transmit the
actual transport address in this case, but instead transmits the address of the
addressed SIP subscriber in order to facilitate a direct RTP stream for the SIP
subscriber.
Given the fact that H.323 and SIP both use RTP for voice transmission,
connection between
• H323,
• SIP and HFA subscribers,
• IPDA: HiPath Host system and IPDA Access Points,
• Common Gateways (IP /SIP trunking) and HG 1500 gateways
is possible.
To set up a standards-compliant payload channel for the SIP subscriber, the SIP
re-invite and, preferably (provided the subscribers support it), the SIP update
procedures are used (the latter also requires SIP-PRACK support). These
procedures make it possible to switch a payload connection over to another
destination. Unlike previous DMC endpoints, the “master” payload connection to
HiPath 4000 is not maintained in this case - i.e. the DMC payload connection
replaces the master connection. However, the “master” signaling for the HiPath
4000 remains established.
This is illustrated in the figure below:
Anate/TDM phone
Node 200 Node 300
HG 3500 -
HG 3500 HG 3500-
Trk
SIP Sub Trk
SIP IP Trunk
SIP Subscriber Slave signaling Master signaling

Slave Payload Master Payload
Figure 2 HG 3500 subscriber which functions as a DMC proxy
Explanation:
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Restriction
Figure 1 DMC in connection with HFA subscriber: DMC signaling and payload
between an HFA telephone and an HG 3500 trunking gateway (see also Chapter
2, “Direct Media Connect (DMC) in Connection with HFA Subscriber”).
Figure 2 HG 3500 subscriber which functions as a DMC proxy: DMC payload

is sent between the SIP phone in node 200 and an HG 3500-Trunking in Node
300. DMC signaling is between the DMC proxy in HG 3500 board and the HG
3500-SIP-Trunking board.
A distinction is made between the DMC proxy and the DMC endpoint. The latter
is the endpoint for DMC signaling and the DMC payload channel (RTP). Both
gateways (HG 3500, HG 3575) and subscribers function as DMC endpoints. HG
3500-Trk in node 300 and the SIP phone in node 200 are therefore DMC
endpoints in the diagram.
Note that the HG 3500 in this example is not part of a payload connection.
However, a DSP is reserved for the connection in case activation of a feature
terminates the DMC and causes a fallback to the master connection. When the
DMC is terminated, a master payload connection must be renegotiated by SIP re-
invite, as the connection does not exist for the SIP subscriber.
Given the fact that the SIP subscribers are themselves not DMC-capable, we no
longer talk about DMC connections as of HiPath 4000 V3.0, but instead more
generally about an end-to-end payload connection, or e2epc for short.
Setup of the master connection, which leads to a master payload connection

between the calling SIP endpoint and HG 3500 (requested in order to transmit
announcements and tones from the HiPath 4000 to the SIP endpoint) is not
displayed. DMC is initiated with the Connect of the called side.
The procedure described above is even used for a call between two SIP
subscribers, i.e. an H.323-based DMC is set up from HG 3500 to HG 3500 (or
internally if both subscribers are registered on the same gateway). A direct
connection between HiPath 4000 SIP subscribers without DMC is not possible at
present.
3.2 Restriction
IMPORTANT: When connecting a fax adapter to a HG 3500 (SIP subscriber),

DMC must be deactivated for this device (only then is T.38 transmission
possible).
If you want nonetheless to connect DMC for this device, the codec must be set to
G.711 (fax transmission with G.711, not T.38).
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3 Scenarios
The diagrams in the following sections illustrate the possible scenarios in which
a SIP subscriber is involved in an e2epc, for example DMCs to HFA and SIP
stations in the same (or in a different) node, and DMCs to IPDA and IP trunking
boards - the latter functioning as DMC endpoints.
3.3.1 SIP Subscriber at same HiPath 4000

DMC signaling between the HG 3500s (or internally, if both are on the same
gateway), e2epc between the stations, which replaces the master payload
connection to the gateway.
HiPath 4000
HG 3500
SIP Sub
The B channel of the DSP stays reserved in
case a SIP phone activates a feature.
The SIP phone must do a re-invite message,

as that the master connection does not exist.
SIP
Subscriber
SIP
Subscriber
e2epc end to end
payload
connection
master signaling slave signaling
master payload slave payload
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.2 SIP Subscriber at another HiPath 4000

Slave signaling to HG 3500 SIP subscriber board, slave payload to the SIP
subscriber.
SIP subscriber A sets up a call to HiPath 4000 A. HiPath 4000 A routes the call
via a trunking connection to HiPath 4000 B. HiPath 4000 B then sets up a
connection to SIP subscriber B. HiPath 4000 B initiates a DMC between SIP
subscriber B and SIP subscriber A, resulting in an end-to-end payload
connection.
HiPath 4000 A HiPath 4000 B
HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q
SIP Sub Trunk Trunk SIP Sub
IMPORTANT: SIP-Q master connection still
e2epc end to end payload

connection
SIP
Subscriber
SIP B
Subscriber
A

A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.3 SIP Subscriber at OpenScpae Voice

Slave signaling to HG 3500 SIP subscriber board, slave payload to the SIP
subscriber.
via a trunking connection to HiPath 4000 B. HiPath 4000 B routes the call via
another trunking connection to OpenScape Voice. OpenScape Voice then sets up
a connection to SIP subscriber B. HiPath 4000 B initiates a DMC between SIP
trunking gateway B and SIP subscriber A, resulting in an end-to-end payload
connection.
HiPath 4000 B
HiPath 4000 A
HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q SIP-Q
SIP Sub Trunk Trunk Trunk

connection SIP
Subscriber
SIP B
Subscriber
A IMPORTANT: End to end payload connection
OpenScape Voice
between SIP subscriber (OpenScape Voice) and
SIP subscriber (HiPath 4000) is not possible!

A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.4 SIP Subscriber at HiPath 3000

DMC signaling between HG 3500 and HG 1500 (initiated by HiPath 4000), e2epc
between SIP subscribers.
HG 3500 HG 3500 HG 1500

SIP-Q SIP-Q
Trunk Trunk
SIP
Subscriber
connection
SIP
Subscriber
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.5 HFA Subscriber at same HiPath 4000

DMC signaling between HG 3500 and HFA subscriber, e2epc between the
stations. A master payload connection to the HG 3500 (HFA subscriber) is
retained.
HiPath 4000 The B channel of the DSP stays reserved in

case a SIP subscriber activates a feature.
HG 3500 HG 3500 The SIP subscriber must do a re-invite

message, as that the master connection does
HFA Sub SIP Sub not exist.
„HG 3500 SIP Sub“ acts as DMC proxy.
SIP
Subscriber
HFA
Subscriber e2epc end to end payload
connection
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.6 HFA Subscriber at another HiPath 4000
Example 1: End-to-end payload between HFA and SIP subscriber (also HG

3575 and SIP subscriber)
No specific action is necessary with the HG 3500 trunking boards. HiPath 4000
B initiates a DMC between the SIP subscriber and HFA subscriber, resulting in an
end-to-end payload connection.
HG 3500 HG 3500 HG 3500 HG 3500

HFA, SIP-Q SIP-Q SIP-Q
IPDA Trunk Trunk Trunk
HFA
Subscriber
SIP
Subscriber
HG 3575
SIP-Q
Trunk
HiPath 4000
AP
TDM
Subscriber

A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
Example 2: End-to-end payload between HFA and SIP trunk (also HG 3575
and SIP trunk)
HG 3500 HG 3500 HG 3500

HFA, SIP-Q SIP-Q
IPDA Trunk Trunk
TDM
Subscriber
HFA
Subscriber
HG 3575
SIP-Q
Trunk
HiPath 4000
AP
TDM
Subscriber
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.7 HFA Subscriber at HiPath 3000

Master signaling via HG 1500, master payload between HFA subscriber and
neighboring HG 3500, slave signaling between HFA subscriber and initiating HG
3500 and slave payload between SIP and HFA subscriber.
HG 3500 HG 3500 HG1500

SIP-Q SIP-Q
Trunk Trunk
HFA
e2epc end to end payload Subscriber
connection
SIP
Subscriber
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.8 TDM Subscriber/Network behind a Remote Shelf

of a HiPath 4000
DMC signaling between HG 3500 and HG 3575, e2epc between SIP subscriber
and HG 3575.
HiPath 4000 The B channel of the DSP stays reserved in

case a SIP subscriber activates a feature.
The SIP subscriber must do a re-invite

HG 3500 HG 3500 message, as that the master connection does
not exist.
IPDA SIP Sub
SIP
Subscriber

connection
HG 3575
TDM
Subscriber
HiPath 4000 - AP-IP
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.9 TDM Subscriber/Network at another HiPath 4000

behind a Remote Shelf
Slave signaling and payload to HG 3575.
HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q SIP-Q
IPDA Trunk Trunk Trunk
TDM
Subscriber
SIP
e2epc end to end payload Subscriber
connection
IPDA
HG 3575 OpenScape Voice
TDM
Subscriber

A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.10 TDM Subscriber/Network at another HiPath

4000
Example 1: Slave signaling and payload to HG 3500.
HiPath 4000 B HiPath 4000 C
HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q SIP-Q
Trunk Trunk Trunk
TDM
Subscriber

connection
SIP
Subscriber
HG 3500
OpenScape Voice
HiPath 4000 A
TDM
Subscriber

A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
Example 2: DMC signaling between HG 3500 (SIP subscriber) and HG 3500

(Trunk), e2epc between SIP subscriber and HG 3500.
via a trunking connection to HiPath 4000 B. HiPath 4000 B then sets up a
connection to TDM subscriber B. HiPath 4000 B initiates a DMC between HG
3500 in HiPath 4000 B and the HG 3500 in HiPath 4000 A. HiPath 4000 A
ensures that an end-to-end payload connection (e2epc) is established between
SIP subscriber A and the HG 3500 in HiPath 4000 B.
HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q
Trunk Trunk
TDM
Subscriber
B

connection
SIP
Subscriber
A
A31003-H3160-S104-8-7620, 07/2014
dmc_03_sip.fm
Scenarios
3.3.11 TDM Subscriber at HiPath 3000

Master signaling and payload between HG 1500 and neighboring HG 3500, slave
signaling and payload between HG 1500 and initiating HG 3500.
TDM subscriber at HiPath 3000 sets up a connection to HiPath 4000 A. HiPath

4000 A routs the call via a trunking connection to HiPath 4000 B. HiPath 4000 B
routes the call via another trunking connection to OpenScape Voice. OpenScape
Voice then sets up a connection to SIP subscriber B. HiPath 4000 B sets up a
DMC between HG 3500 in HiPath 4000 B and HG 1500 in HiPath 3000.
HiPath 3000
HG 1500
SIP-Q
Master signaling 
& Payload
e2epc end to end
payload
connection
TDM
Subscriber
Master signaling 
& Payload
HG 3500 HG 3500 HG 3500
SIP-Q SIP-Q SIP-Q
Trunk Trunk Trunk
TDM
Subscriber
SIP
Subscriber
B

master payload slave payload OpenScape Voice
A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Direct Media Connect (DMC) in Connection with HiPath 4000 SoftGate
4 Direct Media Connect (DMC) in Connection with HiPath

4000 SoftGate
NOTE: For SIP subscriber:

If DMC is not active, the payload is exchanged between the SIP subscriber and
its HG 3500 (or vHG 3500). If DMC is active, the payload is exchanged exclu-
sively via the end-to-end payload path.
A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 1: HFA Subscriber A at HiPath 4000 A calls HFA Subscriber B at

HiPath 4000 A
HG 3500
HFA Sub
HG 3575
HFA
Subscriber
A
vHG 3575
e2epc end to end
payload
connection
vHG 3500
HFA Sub
HFA
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 2: SIP Subscriber A in HiPath 4000 A calls SIP Subscriber B at

HiPath 4000 A
HG 3500
SIP Sub
HG 3575
SIP
Subscriber
A
e2epc end to end

payload
vHG 3575 connection
vHG 3500
SIP Sub
SIP
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 3: SIP Subscriber A at HiPath 4000 A calls HFA Subscriber B at

HiPath 4000 A
HG 3500
SIP Sub
HG 3575
SIP
Subscriber
A
e2epc end to end

vHG 3575 payload
connection
vHG 3500
HFA Sub
HFA
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 4: HFA Subscriber A at HiPath 4000 A calls SIP Subscriber B at

If a SIP device or SIP native trunk on HiPath 4000 SoftGate communicates with
a DMC endpoint (not DMC proxy!), a media relay on the HiPath 4000 SoftGate is
always switched between them. This corresponds to an RTP proxy which always
routes the media stream (RTP) via the HiPath 4000 SoftGate.
HiPath 4000 A
HG 3500
HFA Sub
HG 3575
HFA
Subscriber
A
e2epc end to end

vHG 3575 payload
connection
vHG 3500
SIP Sub
Media
Relay
SIP master signaling slave signaling

Subscriber
B master payload slave payload
A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 5: HFA Subscriber A at HiPath 4000 A calls HFA Subscriber at

HiPath 4000 B HiPath 4000 A
HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q HFA Sub
HG 3575 Trunk Trunk
HFA
Subscriber
A
e2epc end to end

vHG 3575
payload
connection
vHG 3500
HFA Sub
HFA
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 6: SIP Subscriber A at HiPath 4000 A calls SIP Subscriber at

HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q SIP Sub
HG 3575 Trunk Trunk
SIP
Subscriber
A
vHG 3575

e2epc end to end
payload
vHG 3500 connection
SIP Sub
SIP
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 7: SIP Subscriber A at HiPath 4000 A calls HFA Subscriber B at

HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q SIP Sub
HG 3575 Trunk Trunk
SIP
Subscriber
A
vHG 3575

e2epc end to end
payload
vHG 3500 connection
HFA Sub
HFA
Subscriber
B

A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
Example 8: HFA Subscriber A at HiPath 4000 A calls SIP Subscriber B at

HG 3500 HG 3500 HG 3500 HG 3500

SIP-Q SIP-Q HFA Sub
HG 3575 Trunk Trunk
HFA
Subscriber
A
vHG 3575
e2epc end to end

vHG 3500 payload
SIP Sub connection
Media
Relay
SIP master signaling slave signaling

Subscriber
B master payload slave payload
A31003-H3160-S104-8-7620, 07/2014
dmc_04_softgate.fm
A31003-H3160-S104-8-7620, 07/2014
t38fax_01.fm
Definition
T.38 Fax
T.38 Fax
1 Definition
The T.38 fax standard is a protocol which allows for fax transmission over IP
networks in real time.
A31003-H3160-S104-8-7620, 07/2014
t38fax_01.fm
Definition
T.38 Fax
A31003-H3160-S104-8-7620, 07/2014
t38fax_02.fm
Feature Description
Important Notes
T.38 fax is supported in scenarios with common gateway, HiPath 4000 SoftGate,
IPDA NCUI, and IPDA STMI.
2.1 Important Notes
IMPORTANT: When connecting a fax adapter to a HG 3500 (SIP subscriber),

DMC must be deactivated for this device (only then is T.38 transmission
possible).
If you want nonetheless to connect DMC for this device, the codec must be set to
G.711 (fax transmission with G.711, not T.38).
IMPORTANT: T.38 configuration/usage requires end-to-end DMC between

HiPath 4000 gateways (minimized IP hops) because of timing requirements
according to T.38 standard. In case of multiple IP hops the fax transmission could
fail with some fax machines. Negative list of affected fax machines can be found
in the Release Notes.
IMPORTANT: From loadware hot fix HiPath 4000 V6 R2.14.1 the number of T.38
available fax channels for parallel fax calls has been increased from 4 per DSP
to 60 per STMI. The limit of 60 is independent of STMI type (i.e. whether STMI2/
STMI4 or 60/120 channels. Further fax calls will then be processed with G711
clear channel.
IMPORTANT: When using STMI4/NCUI4 boards a Fax/Modem tone detection

with G729 codec is possible and the gateway will automatically switch to G711
mode. STMI2/NCUI2 boards do not have enough performance capablities to
make this change.
IMPORTANT: If T.38 is supposed to be used with AP 1120, G.711 must be

configured as voice codec only, i.e. always in case a modem or fax is connected
to an AP 1120 the only allowed codec in the AP 1120 has to set to G.711 (no
option for compression).
A31003-H3160-S104-8-7620, 07/2014
t38fax_02.fm
Feature Description
Common Gateway
2.2 Common Gateway

T.38 is possible for
• IP trunking connections (H323 and H323A)
• SIP trunking connections (SIP-Q and native SIP)
• DMC connections from/to IPDA-STMI/HG 3570
2.3 HiPath 4000 SoftGate

The following scenarios are supported with HiPath 4000 SoftGate:
• Analog fax devices at Mediatrix 41xx connected to a virtual HG 3500 (SIP

subscriber interface).
• Fax from central office at Mediatrix 44xx connected to a virtual HG 3500 (SIP
trunk interface).
• Fax from SIP provider / OpenScape Xpression connected to a virtual HG

3500 (SIP trunk interface).
• Fax from another HiPath 4000 / HiPath 4000 system connected to a virtual
HG 3500 (SIP/SIP-Q trunk interface).
• Fax from another HiPath 4000 SoftGate, IPDA NCUI or IPDA STMI.
Each interface supports the switchover to T.38 based on tone evaluation.
2.4 IPDA
The following scenarios are supported with IPDA:
• Analog fax devices connected to SLMA in the host or access point shelf.
• Analog fax devices at Mediatrix 41xx connected to HG 3500 (SIP subscriber

interface).
• Fax from central office connected to TDM trunk board.
• Fax from SIP provider connected to HG 3500 (SIP trunk interface).
• Fax from another HiPath 4000 / HiPath 4000 system connected to HG 3500
(SIP trunk interface).
• Fax from another HiPath 4000 SoftGate, IPDA NCUI, or IPDA STMI.
NCUI and IPDA STMI support the switchover to T.38 based on tone evaluation
on the master call and DMC slave call.
A31003-H3160-S104-8-7620, 07/2014
t38fax_02.fm
Feature Description
IPDA
A31003-H3160-S104-8-7620, 07/2014
t38fax_02.fm
Feature Description
IPDA
A31003-H3160-S104-8-7620, 07/2014
t38fax_03.fm
Scenarios
3 Scenarios
HiPath 4000 allows using T.38, also on the master channel. The following figures
show some supported scenarios:
Scenario 1: HiPath 4000 SoftGate - HiPath 4000 host system
Figure 1 HiPath 4000 Softgate - HiPath 4000 host system
This scenario shows a typical fax call from a small site with HiPath 4000 SoftGate
at the main site. Usually the connection will be established as a voice call. After
tone detection, a switchover to T.38 will be initiated.
Scenario 2: Fax between SMP enabled endpoints
Figure 2 Fax between SMP enabled endpoints
A31003-H3160-S104-8-7620, 07/2014
t38fax_03.fm
Scenarios
This scenario shows a fax call between SMP (SIP Message Proxy) enabled
endpoints. The media negotiation is performed end to end, i.e. the HiPath 4000
SoftGate is not involved in media handling.
Scenario 3: Media routing in IPv6 scenario
Figure 3 Media routing in IPV6 scenarios
This scenario shows a fax call between IPV4 and IPV6. The conversion between
IPV4 and IPV6 is performed by the HiPath 4000 SoftGate, which functions as
media relay.
Scenario 4: Media relay scenario with DMC (Direct Media Connection)
Figure 4 Media Relay scenario with DMC
This scenario shows a fax call from an HiPath 4000 SoftGate through an HiPath
4000 network (either SIP-Q or TDM) to a hardware access point.
A31003-H3160-S104-8-7620, 07/2014
t38fax_03.fm
Scenarios
A DMC is initiated. In case the fax tones are detected before the DMC has been
established, the DMC is cancelled, and the master channel is used instead. The
HiPath 4000 SoftGate will install a media relay between SIP and H323.
A31003-H3160-S104-8-7620, 07/2014
t38fax_03.fm
Scenarios
A31003-H3160-S104-8-7620, 07/2014
t38fax_04.fm
Service Information
The following T.38-related features are provided with HiPath 4000 SoftGate:
• Codec switching on the fly

The Mediatrix AP 41xx, as well as SIP providers, switch from G.729 to G.711
codec without signaling. Therefore, payload-based switching on the fly on the
receiving side is supported.
• Jitter buffer improvements

With HiPath 4000 V6, a greater buffer is provided for T.38 transmissions. The
buffer size will be switched during a pause (idle) in the media stream.
• Usage of RFC2833 for fax

Albeit discouraged, RFC2833 for fax tones is still supported. However, it is
disabled by default. After a software update, the previously configured value
will be preserved.
IMPORTANT: With some scenarios, the use of RFC2833 for fax tones may
cause problems, so it must be disabled. This is the case with the following
configurations:
- A Mediatrix 41xx adapter is connected to a hardware gateway, and a
AP1120 Cornet IP Adapter is used in the same system. If a DMC shall be
established between both adapters, RFC2833 for fax must be disabled.
- A SIP service provider which does not support RFC2833 for fax is
connected to a hardware gateway.
4.1 HiPath 4000 SoftGate

• SIP
With HiPath 4000 SoftGate, T.38 can be used right from the beginning of a
transmission, that is, with initial SIP invite.
• H323/DMC
DMC uses the existing mechanism to support a switchover to T.38 (actively
and passively).
4.2 IPDA (NCUI/STMI)

In IPDA, two main fax connections can be distinguished:
• DMC (NCUI/STMI as endpoint) and
A31003-H3160-S104-8-7620, 07/2014
t38fax_04.fm
Service Information
IPDA (NCUI/STMI)
• master calls.
Master / Slave Connection

The master connection is controlled by the host system, whereas the slave
connection (DMC) is controlled by the board itself.
Since IPDA master connections are not controlled by H323, IPDA endpoints
detect T.38 with tone evaluation. Each IPDA endpoint sends a message to the
DNIL in the SWU stating that T.38 is possible. If this is the case, DMC is rejected.
When the DNIL has received the messages, a T.38 path switch message is sent
to the endpoints.
Restrictions
• Maximum of 4 T.38 channels per DSP
If no T.38 resources are available, G.711 is used as an alternative. The
resource limitation is signaled to the DNIL.
This restriction applies to all hardware gateways.
• QoS Monitoring
QoS monitoring on the T.38 (former voice) channel is adapted to T.38 to that
effect that T.38 is always regarded as "good quality". Hence, no
BAD_QUALITY messages are generated.
• Bandwidth Management
The consumed bandwidth depends on the selected redundancy factor and
the fax transmission speed. There is no specific bandwidth management for
T.38; it will be counted like G.711, with 30ms packet size.
This restriction also applies to connections other than IPDA.
A31003-H3160-S104-8-7620, 07/2014
t38fax_05.fm
The following parameter settings are taken from a working configuration; it
applies to all scenarios described in this chapter (see Chapter 3, “Scenarios”).
TOSPL = 184 (184) TOSSIGNL = 104 (104)
UDPPRTLO = 29100 (29100) UDPPRTHI = 30999 (30999)
T38FAX = YES (YES) REDRFCTN = YES (YES)
RFCFMOIP = NO(NO) RFCDTMF = YES (YES)
PRIO1 : CODEC = G711A VAD = NO RTP-SIZE = 30
PRIO2 : CODEC = G729A VAD = NO RTP-SIZE = 20
PRIO3 : CODEC = G723 VAD = NO RTP-SIZE = 30
PRIO4 : CODEC = NONE VAD = NO RTP-SIZE = 20
PRIO7 : CODEC = G729AB VAD = YES RTP-SIZE = 20
A31003-H3160-S104-8-7620, 07/2014
t38fax_05.fm
A31003-H3160-S104-8-7620, 07/2014
t38fax_06.fm
Relevant AMOs
6 Relevant AMOs

Language
CGWB T38FAX d Schaltet T.38 generell ein oder aus.
Weitere Parameter, zur Konfiguration der
T.38-Funktionalität befinden sich im WBM.
T38FAX e Switches T.38 on or off generally.
Further parameters for configuring the T.38
functionality are to be found in the WBM.
RFCFMOIP d Schaltet RFC 2833 für Fax/Modem-Töne
ein oder aus. Steht der Parameter auf JA, so
werden die Fax/Modem-Töne als RFC
2833-Events übertragen. Der Parameter
hat nur Einfluss auf die Tonübertragung,
also auf den Sprachkanal. Somit ist er nur in
der Phase vor dem Start des T.38-Stacks
relevant.
Der Parameter muss im gesamten System
auf den gleichen Wert gesetzt wird.
RFCFMOIP e Switches RFC 2833 for fax/modem tones on
or off. If the parameter is set to YES, the fax/
modem tones are transmitted as RFC 2833
events. The parameter influences only the
tone transmission, that is, the speech
channel. Thus, it is only relevant within the
phase before the T.38 stack is started.
The parameter must be set to the same
value in the entire system.
REDRFCTN d Schaltet RFC 2198 ein oder aus. Steht der
Parameter auf JA, so werden die RFC
2833-Events redundant übertragen. Der
Parameter hat nur Auswirkungen, wenn
RFC 2833 eingeschaltet ist
(RFCFMOIP=JA).
Der Parameter muss im gesamten System
auf den gleichen Wert gesetzt wird.
REDRFCTN e Switches RFC 2198 on or off. If the
parameter is set to YES, the RFC 2833
events are transmitted in redundant fashion.
The parameter is only effective when RFC
2833 is switched on (RFCFMOIP=YES).
The parameter must be set to the same
value in the entire system.
A31003-H3160-S104-8-7620, 07/2014
t38fax_06.fm
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_01_supported_ep.fm
Supported IP Terminals
IP Terminals
IP Terminals
1 Supported IP Terminals
The following IP terminals (HFA) are supported:
• OpenStage HFA
• optiPoint 410/420 CorNet IP
• optiPoint WL2 professional
• AP 1120 CorNet-IP (only HG 3500)
• AC-Win IP
• OpenScape Personal Edition HFA
IMPORTANT: For the released SIP terminals please refer to section „SIP
Connectivity“ > Chapter 2, “SIP Subscriber”.
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_01_supported_ep.fm
Supported IP Terminals
IP Terminals
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_02_boards.fm
Boards
2 Boards
IP terminals can be configured on the following boards with an Ethernet interface:
• STMI2 (Q2316-X)
• STMI2 (Q2316-X10)
• STMI4 (Q2324-X500)
• STMI4 (Q2324-X510)
• vHG 3500 with HiPath 4000 SoftGate
IMPORTANT: To simplify matters, the following document only refers to the

STMI board. This term will be used generically for all suitable boards.
The term “HFA port“ is used in the following to describe an IP port to which all IP
system telephones can be connected (see Chapter 3, “Description of optiPoint IP
Terminals” and Chapter 4, “Description of OpenStage IP Terminals”).
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_02_boards.fm
Boards
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_03_optipoint_ip.fm
Description of optiPoint IP Terminals
General Information
3 Description of optiPoint IP Terminals

You can connect additional terminals to an optiPoint IP telephone using the
appropriate adapters that must be attached to or are already integrated in the
telephone:
• The USB adapter (OPTIUSB) is already integrated as a hardware module in

most optiPoint 410 telephones.
• Every optiPoint 410 is assigned “control adapter“ functionality during

configuration so that a PC can be connected as a simple dialer using the USB
adapter.
You can connect up to two key modules to an optiPoint 410 IP telephone. These
must be specified with the REP parameter. You can configure other key modules
but they won’t work.
IMPORTANT: Analog terminals require the optiPoint to be fed locally via a plug-
in power supply.
Country- and transmission-specific settings are made centrally using the
AMO ZAND:TYPE=OPTISET,TAABCTID=<string>.
3.2 optiPoint 410/420
3.2.1 Terminal Types

There are a number of different optiPoint 410 telephone types that only differ on
the basis of their functional scope and expansion capabilities. The following table
provides an overview:
optiPoint  No. of Display No. of Poss. no. USB Headset

telephone types functio adapter of 1.1 port
n *) lit slots key *)
keys modules master
optiPoint 410 entry 8 No 0 0 No No
optiPoint 410 12 Yes 0 0 No No
economy
optiPoint 410 12 Yes *) 2 2 Yes Yes
standard
A31003-H3160-S104-8-7620, 07/2014
optiPoint 410/420
optiPoint  No. of Display No. of Poss. no. USB Headset

telephone types functio adapter of 1.1 port
n *) lit slots key *)
keys modules master
optiPoint 410 19 Yes *) 1 2 Yes *) Yes
advance 4 lines
optiPoint 420 18 Yes *) 1 2 Yes *) Yes
advance  4 lines
(up to 12
characters per
label)
All optiPoint 410 models support Power over LAN feeding (Cisco or IEEE
802.3af). A plug-in power supply unit can be used at the same time as Power over
LAN.
3.2.2 Adapters and key modules

The following optiPoint adapters and add-on devices can be operated at the
optiPoint 410 system telephone:
Device type Function AMO

parameter
optiPoint USB adapter For connecting standard S0 data terminals OPTIUSB
(already integrated in
the telephone)
optiPoint key module Key module with 15 programmable function REP
keys and 1 SHIFT key
optiPoint 420 key Key module with 13 keys with electronic key REP
module labeling, 12 of which are programmable (up to
12 characters per label) and 1 SHIFT key
optiPoint signature Key module with smart card reader IDCR
module
OpenStage Busy Lamp Busy lamp filed with 90 illuminated, OPTIBLF
Field programmable keys
optiPoint display For providing the LDAP/WAP and ENB function, ---
module as well as JAVA VM
optiPoint recorder For connecting a second headset or an external ---
adapter recorder
optiPoint acoustic For connecting accessories (such as ---
adapter loudspeakers, microphones, headsets, etc.)
A31003-H3160-S104-8-7620, 07/2014
optiPoint WL2 professional
3.3 optiPoint WL2 professional

The optiPoint WL2 professional telephone is the enhanced telephone for mobile
workplaces that use WLAN technology for transmission. It is interpreted by
HiPath 4000 as an optiPoint 420 and thus offers the complete range of HiPath
4000 features (HFA).
More information on the optiPoint WL2 professional may be found on the intranet
on E-Doku: http://apps.g-dms.com:8081/techdoc > Product: optiPoint WL2
professional
For HiPath 4000 configuration see Section 7.1, “optiPoint WL2 professional
Configuration”.
3.4 More Adapters and Ports
3.4.1 OpenStage Busy Lamp Field
IMPORTANT: As of HiPath 4000 V6 R2.15 the OpenStage busy lamp field is also
supported for optiPoint 410/420 IP.
The DIGTYP value OPTIBLF has been introduced for the busy lamp field in AMO
TAPRO. A layout with this type has to be used for the key layout configuration of
an optiPoint device with BLF.
The key configuration is similar as for an OpenStage device with busy lamp field.
Not 90 keys are configured on one add-on device but 5 add-on devices each with
18 keys. So each column with 18 keys on the busy lamp field can be thought as
one add-on device.
Configuration
A number for the key layout (SNU=127) for the DIGTYP=OPTIBLF must be
configured.
Example:
CHANGE-TAPRO:STD=127,DIGTYP=OPTBLF,KY01=CH;
REGEN-TAPRO:TYPE=STD,STD=127;
CHANGE-TAPRO:,127,OPTIBLF ,CH ,FREE ,FREE ,FREE ,FREE ,
FREE ,FREE ,FREE ,FREE ,FREE ,
FREE ,FREE ,FREE ,FREE ,
" ";
A31003-H3160-S104-8-7620, 07/2014
More Adapters and Ports
CHANGE-TAPRO:,127,OPTIB1 ,FREE ,FREE ,FREE ,FREE ,FREE ,

FREE ,FREE ,FREE ;
FREE ,FREE ,FREE ;
FREE ,FREE ,FREE ;
FREE ,FREE ,FREE ;
FREE ,FREE ,FREE ;
AMO-TAPRO-111 PROGRAMMABLE KEY DEFINITION FOR DIGITAL

TERMINALS
REGENERATE COMPLETED;
Additionally the parameters REP=0 and BLF=YES must be set in AMO SBCSU
for the subscriber.
3.4.2 optiPoint Recorder Adapter

The recorder adapter lets you connect an analog recording device or a second
headset to an existing optiPoint 410 device.
IMPORTANT: This adapter is not configured in the PBX and consequently does
not feature a parameter value in the AMO SBCSU display mask.
A31003-H3160-S104-8-7620, 07/2014
3.4.2.1 Port for Recording Device (Data cannot be modified)
During a call, the RX and TX handset signals are both routed to the jack.
– Impedance: 6 kOhm
– Frequency range: 300 to 3000 Hz (+/- 3 dB)
– Level: 1.77 Vrms at 600 Ohm
Jack MW6/4 assignment:

pin 1 = unassigned
pin 2 = AF +
pin 3 = AF +
pin 4 = AF
pin 5 = AF
pin 6 = unassigned
Figure 1 Recorder interface assignment
3.4.2.2 Second Headset Port
A second headset can be used as soon as it is connected and uses the same
volume setting as the telephone to which the adapter is connected.
The volume cannot be separately set for this port.

pin 1 = unassigned
pin 2 = AF +
pin 3 = AF -
pin 4 = unassigned
Figure 2 Second headset port assignment
A31003-H3160-S104-8-7620, 07/2014
3.4.3 optiPoint Acoustic Adapter Data

The acoustic adapter lets you connect an external microphone and speaker as
well as a headset (cordless or corded) to an existing optiPoint 410 device. The
adapter also features two floating contacts.
IMPORTANT: This adapter is not configured in the PBX and consequently does
not feature a parameter value in the AMO SBCSU display mask.
3.4.4 Microphone and Loudspeaker Port

You can operate an add-on microphone and an external speaker at this port by
using a cable-sharing adapter.
IMPORTANT: Any external devices connected cancel out the corresponding

internal devices. No configuration changes are necessary at the PBX.
– The volume can be modified in the same way as for the telephone.
– The external loudspeaker must have a separate amplifier and power

supply.
.
MW8/8 assignment:
RJ45 jack
pin 1 = MIC power +
pin 2 = MIC power GND
pin 3 = MIP (AF in)
pin 4 = MIC sense lead
pin 5 = SPKR sense lead
pin 6 = LSP (AF out)
pin 7 = reserved (BOOT)
pin 8 = GND
Figure 3 Microphone/loudspeaker port assignment
A31003-H3160-S104-8-7620, 07/2014
3.4.5 Headset Port

Headsets with and without key as well as wireless or wired units can be operated
at this port.
IMPORTANT: If you are using a headset without hardware detection (that is,
connection/disconnection is n o t recognized by the hardware), you must confirm
its presence by pressing the HS key (HandSet, assigned with the AMO TAPRO).
The parameter HEADSET must be set to NOIND in the AMO SBCSU and HSKEY
must be set to correspond to the function.
A headset with a MW4/4 port needs an adapter.
RJ45 jack MW8/8 assignment:

pin 1 = serial interface TX bus
pin 2 = GND
pin 3 = TX Audio
pin 4 = RX Audio
pin 5 = RX Audio
pin 6 = TX Audio +Power electret mic.
pin 7 = reserved (+3V3)
pin 8 = serial interface RX bus
Figure 4 Headset port assignment
3.4.6 Contact Port

The “bell“ contact is activated when an alert message is received for the terminal.
The second contact “activity“ can be activated by pressing the keys configured
with the AMO TAPRO (BUSYLAMP or DOOROPEN).
The contact is closed the first time you press the “BUSYLAMP“ button and re-
opened when you press it a second time.
(The LED for the associated key is set and then re-set at the same time.)
IMPORTANT: This adapter is not configured in the PBX but must be present so
that the door opener and busy lamp field function can be key-operated.
– The contacts are galvanically isolated from the telephone.
– Load capacity for the AC contacts: 24 V/5 W
A31003-H3160-S104-8-7620, 07/2014
– Load capacity for the DC contacts: 60 V/5 W

pin 1 = activity 1
pin 2 = activity 2
pin 3 = bell 1
pin 4 = bell 2
Figure 5 Contact port assignment
IMPORTANT: An external power supply must be available for the bell contact
function.
(Not necessary if only using a headset or microphone/loudspeaker.)
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_04_openstage_ip.fm
Description of OpenStage IP Terminals
Hardware and General Features
4 Description of OpenStage IP Terminals

The OpenStage family is released for the use at HiPath 4000. Please refer to the
corresponding release notes regarding the released terminal types.
4.1 Hardware and General Features

Please refer to the data sheet of the OpenStage terminals (http://apps.g-
dms.com:8081/techdoc/en/P31002S2000D101017629/index.htm)
IMPORTANT: There are no adapters for OpenStage telephones.
IMPORTANT: Both key modules, the application modules, the display modules,
the busy lamp field and the adapters in the optiPoint series of telephones cannot
be deployed or operated together with OpenStage. The only exception is the
external power supply (L30250-F600-A190-A191-A192) for the telephones.
4.2 Key Assignment

OpenStage telephones have fixed keys. For this reason, the correct standard key
layouts must be assigned. The keys 1-8 must correspond to the examples
illustrated in Section 7.2, “OpenStage Configuration”. The variable keys start from
key 9 onwards.
A SHIFT key can also be programmed for the telephone itself.
4.3 Key Modules

OpenStage telephones may have up to two key modules. The SHIFT key can be
used to switch between two levels.
Device type Function AMO

parameter
OpenStage key module Key module with 15 programmable function REP
keys (and 1 SHIFT key)
A31003-H3160-S104-8-7620, 07/2014
OpenStage Terminal in Connection with optiClient
SHIFT key
When the SHIFT key is pressed on an optiPoint key module, the same action is
performed on all other key modules. In other words, the SHIFT level is also
activated on the second and fourth key modules.
This is not the case on OpenStage telephones and key modules. In this case,
the SHIFT level is only activated on the telephone/key module on which the
SHIFT key was pressed.
4.4 OpenStage Terminal in Connection with optiClient

The following administration instructions and restrictions are temporarily for the
first roll-out of the release 2. An improved handling will be enabled as soon as
possible.
• The openStage of type "nn" has to be configured with the fitting standard key
layout "openStage nn".
• It is not allowed to change the key assignment for a phone (AMO TAPRO)
while the optiClient is active.
• The individual change of key settings by the subscriber must not be enabled
for the combination optiClient/openStage.
• When the user previously owned the combination optiClient/optiPoint then

he/she is to be informed about the new key layout which can be seen in the
optiClient application. Reason for this are the fixed key functions at
openStage phones.
In case of disregarding the mentioned restrictions the proper key assignment

cannot assured when changing from openStage to optiClient and vice versa. This
can be repaired only with deleting and configuring the complete connection again.
Configuration of a new optiClient/openStage connection:

New configuration of the openStage phone with the proper standard key layout
together with the configuration of the optiClient (OPTIIP&API).
The device "optipoint 420 advance" is to be chosen in the optiClient application.
Replacement of an existing optiClient/optiPoint configuration with

optiClient/openStage:
1. Regeneration of the user data
2. Delete the connection completely

Note: the deletion is necessary because it is currently the exclusive way to
delete the so-called shadow table for key assignments. If it is not cleared
correctly, the proper key assignment is not assured neither at the optiClient
A31003-H3160-S104-8-7620, 07/2014
Busy Lamp Field
nor at the openStage. It depends on what had happened at the connection

previously (i.e. different phone types were connected etc) if the shadow table
has to be cleared.
3. The phone can be exchanged now
4. New configuration of the openStage phone as described above
5. Or the phone can be exchanged now
4.5 Busy Lamp Field

Feature Description
The OpenStage Busy lamp field is a key module attached to the side of the phone,
that provides 90 illuminated, programmable keys.
Like keys on the phone, these keys can be programmed and used according to
your needs.
Service Information
• You can attach one OpenStage Busy lamp field to your OpenStage.
• Only internal destinations can be programmed.
Configuration (Example)
Configuration of the busy lamp field:
CHANGE-TAPRO:STD=61,DIGTYP=OST30BLF;
Relevant AMOs
AMO Parameter Sprache/ Beschreibung/ Discription

Language
TAPRO DIGTYP d OST30BLF - OpenStage 30 BLF
OST40BLF - OpenStage 40 BLF
(entkoppelte Freigabe)
DIGTYP e OST30BLF - OpenStage 30 BLF
(decoupled release)
A31003-H3160-S104-8-7620, 07/2014
Busy Lamp Field
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_05_sip.fm
SIP Subscriber
5 SIP Subscriber
See „SIP Connectivity“ > Chapter 2, “SIP Subscriber”.
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_05_sip.fm
SIP Subscriber
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_06_service_information.fm
Service Information
General Configuration Rules and Information
6.1 General Configuration Rules and Information

• IP terminals must be configured not only in the system but also at the terminal
itself.n external
• If SPE is activated at the IP endpoints an external NTP server must be used

for time synchronization. For that HiPath 4000 Assistant should not be used.
The performance of the hardware/software of the HiPath 4000 Assistant is
not sufficient for this use case.
• A SoftClient is configured like an optiPoint telephone (you can therefore

replace an optiPoint IP telephone with a SoftClient).
• LAN port settings should always be made on the telephone to avoid duplex
mismatch.
• There is no adapter for OpenStage telephones.
• A host/client configuration is only possible with OpenStage telephones.
6.2 Adapter for optiPoint Telephones

• If not already available, an OPTIUSB (optiPoint USB adapter) is automatically
configured when you set up a functional terminal.
A physical adapter is not necessary because the function, depending on the
terminal, is already implemented.
• optiPoint IP telephones cannot be used for host/client configurations.
IMPORTANT: The command DISPLAY-SBCSU:STNO=number; displays all

configured adapters, that is, both the ones that were explicitly configured and
those that were automatically configured.
6.3 Modules for optiPoint Telephones

• Only one optiPoint signature module is permitted per optiPoint telephone.
• An optiPoint 420 key module must be de-energized before it is connected to

an optiPoint 410.
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_06_service_information.fm
Service Information
Key Layout on optiPoint Telephones
• No specific configuration is necessary in the system for the optiPoint display

module.
IMPORTANT: A suitable plug-in power supply must be connected for config-

uration with the optiPoint acoustic adapter when using the contact.
• You can only connect one optiPoint display module to the optiPoint 410.
• An optiPoint display module should always be directly connected to the

optiPoint 410 as the first key module.
6.4 Key Layout on optiPoint Telephones

• The optiPoint 410 advance and the optiPoint 420 advance use different key
layouts.
o o o
o o
o o
Figure 6 Key layout: optiPoint 420 advance and optiPoint 420 key module
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_07_configuration.fm
IP Terminal Generation
An optiPoint 410 or OpenStage at STMI
7 IP Terminal Generation
For detailed information on HiPath Feature Access (HFA), refer to "HiPath
Feature Access (HFA)".
Please note that all types of generation require settings to be made at the terminal
itself.
The necessary settings to be made include the following network-specific data

(this data can also be automatically programmed via DHCP if the telephone is
appropriately configured (default factory setting)):
• Terminal IP Address (STN IP)
• Terminal Mask (netmask)
• Default Gateway
• (VLAN ID)
The mandatory system parameters for HFA operation are:
• PBX Address
• Subscriber Number
7.1 An optiPoint 410 or OpenStage at STMI
Plug-in power supply

HiPath 4000
Customer network
optiPoint 410 or
OpenStage
IP IP
LAN/MAN/WAN STMI
STNO 3100
Figure 7 HFA (IP) terminal with plug-in power supply
A31003-H3160-S104-8-7620, 07/2014
PC After optiPoint 410
HiPath 4000
Customer network
for example, optiPoint 410
PowerHub
IP IP
LAN/MAN/WAN STMI
STNO 3200
Figure 8 HFA (IP) terminal with PowerHub power supply
To configure an IP telephone at the STMI, enter:

ADD-SBCSU:STNO=<number>,TYPE=OPTI,CONN=IP2,PEN=<ltg-ltu-slot-
cct>,
DVCFIG=OPTIIP,COS1=<number>,COS2=<number>,LCOSV1=<number>,LCO
SV2=<number>,LCOSD1=<number>,LCOSD2=<number>,ITR=<number>,
DPLN=0,STD=<number>,[IPPASSW=<Password>],HEADSET=WITHIND;
IMPORTANT: For OpenStage : HEADSET=WITHIND must be configured

to get the correct display message in case the headset key is pressed and no
headset is connected.
7.2 PC After optiPoint 410
PC
HiPath 4000
IP Customer network
Port 2
PowerHub
IP IP
LAN/MAN/WAN STMI
Port 1
STNO 3200
Figure 9 PC and HFA station with “single wire to the desk“
• To configure an IP telephone at the STMI, enter:
A31003-H3160-S104-8-7620, 07/2014
An optiPoint 410 and USB for Simple Dialer
cct>,

No special HiPath 4000 configuration is necessary for the PC. You only have to
coordinate the port settings on the telephone with those on the PC network card.
IMPORTANT: You cannot connect a PC without 802.1p/q to an optiPoint 410

where 802.1p/q is active. The 802.1p/q settings should be activated at the
telephone and in the AMO, as well as in the LAN components.
7.3 An optiPoint 410 and USB for Simple Dialer
COMx
USB driver
PC
USB HiPath 4000
Customer network
USB 1.1
PowerHub
IP IP
LAN/MAN/WAN STMI
Port 1
STNO 3200
Figure 10 optiPoint and USB for Simple Dialer
• To configure an IP telephone at the STMI, enter:
A31003-H3160-S104-8-7620, 07/2014
optiPoint WL2 professional Configuration
cct>,

No other configuration steps are necessary.
7.1 optiPoint WL2 professional Configuration

Device configuration
optiPoint WL2 professional devices are configured in the same way as optiPoint
devices:
ADD-SBCSU:STNO=58798,TYPE=OPTI,CONN=IP2,PEN=1-1-9-
0,DVCFIG=OPTIIP,TSI=1,COS1=23,COS2=23,LCOSV1=22,LCOSV2=22,LCOSD1
=1,LCOSD2=1,DPLN=0,ITR=0,SSTNO=N,COSX=0,SPDI=30,SPDC1=0,SPDC2=1,
IDCR=N,REP=0,STD=23,SECR=N,INS=Y,ALARMNO=0,RCBKB=N,RCBKNA=N,DSST
NA=N,DSSTNB=Y,DIGNODIS=N,CBKBMAX=5,HEADSET=N,HSKEY=NORMAL,CBKNAM
B=Y,TEXTSEL=AMERICAN,HMUSIC=0,CALLOG=ALL,PMIDX=2,COMGRP=0,DNIDSP
=Y,IPCODEC=G711PREF;
CHANGE-SDAT:STNO=58798,TYPE=DATA1,NNO=1-1-301;
Key assignment
DISPLAY-TAPRO:STN,58798;
H500: AMO TAPRO STARTED
+--------------+----+---------+------------------------------------------------+
| STATION |STD | DIGTYP | FUNCTION KEYS WHICH DIFFER FROM STANDARD |
+--------------+----+---------+------------------------------------------------+
| 58798 | 23 | OPTISET | |
+--------------+----+---------+------------------------------------------------+
AMO-TAPRO-111 PROGRAMMABLE KEY DEFINITION FOR DIGITAL TERMINALS
DISPLAY COMPLETED;
DISPLAY-TAPRO:FORMAT=STD,STD=23,DIGTYP=OPTISET;
+-----+---------+----------------------------------------------------------------------+
| STD | DIGTYP | “SERVICE INFORMATION“ KEY LAYOUT |
+-----+---------+----------------------------------------------------------------------+
| 23 | OPTIT12 | “12 OPTISET TAC STANDARD “ |
| | | 1 DCPA 2 CONS 3 CNCT 4 HOLD 5 PHML |
| | | 6 SNR 7 CONF 8 FWD 9 MUTE 10 SPKR |
| | | 11 LINE 12 LINE |
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| | OPTIA1 | 1 NAME 2 NAME 3 NAME 4 NAME 5 NAME |
| | | 6 NAME 7 NAME 8 NAME 9 NAME 10 NAME |
| | | 11 NAME 12 NAME 13 NAME 14 DSS 15 DSS |
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| | OPTIA2 | 1 VACANT 2 VACANT 3 VACANT 4 VACANT 5 VACANT |
| | | 6 VACANT 7 VACANT 9 VACANT 9 VACANT 10 VACANT |
A31003-H3160-S104-8-7620, 07/2014
OpenStage Configuration

| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
+-----+---------+----------------------------------------------------------------------+
AMO-TAPRO-111 PROGRAMMABLE KEY DEFINITION FOR DIGITAL TERMINALS
DISPLAY COMPLETED;
Integrated key functionality

ADD-
KCSU:STNO=58798,TYPE=PRIM,PRIMKEY=11,RIOP=YES,ORLNPF=PRIME,TMLNP
F=RING,SGLBMOD=YES,BUSYRING=ALERT,APRIVAT=NO,AICS=NO,LINETONE=NO
,BUSYSIGN=DEACTIVE,PRIOCALL=NOTONE,SAMEPRIO=NOSIGNAL,RINGTYPE=1,
RINGVOL=1,OFFTYPE=DC;
7.2 OpenStage Configuration

Key assignment
Sample standard key layouts for the various OpenStage variants:
DIS-TAPRO:TYPE=STD,STD=55&&58;
+-----+---------+----------------------------------------------------------------------+
| STD | DIGTYP | “SERVICE INFORMATION“ KEY LAYOUT |
+-----+---------+----------------------------------------------------------------------+
| 55 | OPENST20| “8 KEYS I.M. OPENSTAGE PHONE - 20 “ |
| | | 1 SPKR-PRO 2 PROT 3 MUTE-PRO 4 SNR-PROT 5 FWD-PROT|
| | | 6 RLS-PROT 7 MENU-PRO 8 MSG-PROT 9 VACANT 10 VACANT |
| | | 16 VACANT 17 VACANT 18 VACANT 19 VACANT |
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
+-----+---------+--------------------------------------------------------------------+
| | | 1 SPKR-PRO 2 HS-PROT 3 MUTE-PRO 4 SNR-PROT 5 FWD-PROT |
A31003-H3160-S104-8-7620, 07/2014

| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
+-----+---------+--------------------------------------------------------------------+
| | | 1 SPKR-PRO 2 HS-PROT 3 MUTE-PRO 4 PROT 5 FWD-PROT |
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
+-----+---------+--------------------------------------------------------------------+
| 58 | OPENST80| “17 KEYS I.M. OOPENSTAGE PHONE - 80 “ |
| | | 1 SPKR-PRO 2 HS-PROT 3 MUTE-PRO 4 PROT 5 FWD-PROT |
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
A31003-H3160-S104-8-7620, 07/2014

| + - - - - + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -+
+-----+---------+--------------------------------------------------------------------+
SHIFT key
A SHIFT key can also be configured on OpenStage terminals (previously this was
only possible on key modules). This is achieved with the AMO TAPRO or via the
Service menu on the terminal.
AMO TAPRO
CHANGE-TAPRO:STNO=<station number>,KYxx=SHIFT;
IMPORTANT: xx must be greater than 08 since the first 8 keys are fixed. Only
key 9 and onwards can be freely assigned.
A31003-H3160-S104-8-7620, 07/2014
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_08_deleting.fm
Deletion at the IP Port
Deleting All Devices Assigned a Station Number at the IP Port
8 Deletion at the IP Port
8.1 Deleting All Devices Assigned a Station Number at the IP Port

To delete all devices that are assigned a station number, enter (the optional
OFFTYPE parameter with its default setting DC=“deactivate with camp-on“ takes
over the mandatory task of disabling the terminals prior to deletion; this would
otherwise be performed with the AMO DSSU):
DEL-SBCSU:STNO=number,SVC=ALL[,OFFTYPE=DI];
IMPORTANT: You can only delete the device with the main station number if
there are no other devices configured under a secondary station number.
8.2 Deleting NV Services at the IP Port

To delete individual NV services at the IP port, enter (the optional OFFTYPE
parameter with its settings DC=“deactivate with camp-on“ and DI=“deactivate
immediately“ takes over the mandatory task of disabling all terminals prior to
deletion and enabling the remaining terminals again afterwards; this would
otherwise be performed with the AMO DSSU):
DEL-SBCSU:STNO=number,SVC=param [,OFFTYPE=DI];
IMPORTANT: If you used OFFTYPE=NL (no lock) to delete an NV service, then

you must use DSSU to put the remaining terminals back into operation (in
particular the voice terminal as this was not deleted).
8.3 Deleting the IP Telephone’s Key Module

To delete all key modules assigned to a telephone, proceed as follows:
CHANGE-SBCSU:STNO=number,OPT=OPTI,REP=0;
8.4 Deleting IP Telephone Adapters
IMPORTANT: This section only applies to optiPoint and optiClient terminals.
A31003-H3160-S104-8-7620, 07/2014
ip_terminals_08_deleting.fm
Deletion at the IP Port
Deleting IP Telephone Adapters
• You cannot delete the optiPoint USB adapter with an AMO command; it is
automatically deleted at the same time as the last (functional) S0 device at the
IP port.
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_01.fm
Feature Description
HiPath Cordless IP
HiPath Cordless IP
HiPath Cordless IP V1 has been released for connections to the HiPath 4000
SoftGate and HG 3500. 10 DECT IP base stations with handover function are
possible in one cluster per HiPath 4000 SoftGate/HG 3500 which allows up to 10
simultaneous calls.
HiPath Cordless IP V1 allows the operation of the cordless Gigaset professional

devices S3, SL3, and M2 on DECT base stations (BSIP1) which are connected
via LAN. The deployment of mobility solutions using DECT radio standard within
IP environments with SIP users is possible.
Voice over IP users can benefit from the advantages DECT offers in comparison
to WLAN, such as:
• High voice quality by a protected frequency range,
• safe bandwidth and isochronous transmission,
• fewer transmitters by higher range,
• high quantity of simultaneous calls per transmitter (up to 10).
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_01.fm
Feature Description
HiPath Cordless IP
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_02.fm
Service Information
Prerequisites
2.1 Prerequisites
• HiPath Cordless IP uses 192.168.123.x and 169.254.222.x for internal
communication. Therefore this address range must not be used in the voice
over IP infrastructure (LAN network).
• For internal BSIP communication a LAN segment in the range 192.168.x.x

has to be reserved (default: 192.168.1.0).
• BSIP IWU and HiPath 4000 must be in the same LAN segement.
• The IP address of the BSIP IWU serves as an access to the WBM of HiPath
Cordlesss IP via HTTP or HTTPS.
• To set system time the BSIP IWU needs an NTP server.
2.2 Restrctions
Roaming, handover, or overlap between HiPath Cordless IP or HiPath Cordless
Enterprise clusters is not possible.
2.3 More Information

You can find more information on HiPath Cordless IP in the service manual for
HiPath Cordless IP (http://apps.g-dms.com:8081/techdoc/en/
P31003C1010S100017620/index.htm) and in the user manuals of the released
devices.
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_02.fm
Service Information
More Information
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_03.fm
Configuration in HiPath 4000 (Example)
3 Configuration in HiPath 4000 (Example)

The HiPath Cordless IP user must be configured in AMO SBCSU like a SIP
subscriber with the following parameters:
ADD-
SBCSU:STNO=<number>,OPT=FPP,CONN=SIP,DVCFIG=S0PP,COS1=<number>,C
OS2=<number>,LCOSS1=<number>,LCOSS2=<number>,LCOSD1=<number>,LCO
SD2=<number>,PROT=SBDSS1,FIXEDIP=YES,IPADDR=<IP address of the
user>,IPCODEC=G711,SMGSUB=NO,USERID=<name of the user (max. 14
characters)>,
Notes:
• do not assign a password (parameter PASSWD)
• do not assigna a security zone (parameter SECZONE)
The package length must be set to 20 ms in AMO CGWB (parameter RTP in

branch TYPE=ASC).
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_03.fm
Configuration in HiPath 4000 (Example)
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_04.fm
Relevant AMOs
4 Relevant AMOs

Language
BCSU ANSCHL=SIP d Konfiguration eines SIP-Teilnehmers
CONN=SIP e Configuration of a SIP subscriber
FESTEIP=JA d Es muss eine feste IP-Adresse
konfiguriert werden
FEXEDIP=YES e You must configure a fixed IP address
IPCODEC=G711 d Benutzen Sie den IP-Codec “G711”
IPCODEC=G711 e Use the IP codec “G711”
SMGTLN=NO d SMG-Teilnehmer = nein
SMGSUB=NO e SMG subscriber = no
CGWB RTP=20 d RTP-Paketgröße = 20 ms
RTP=20 e RTP package size = 20 ms
A31003-H3160-S104-8-7620, 07/2014
cordless_ip_04.fm
Relevant AMOs
A31003-H3160-S104-8-7620, 07/2014
glossary.fm
Nur für den internen Gebrauch Glossary
Glossary X
D
DMZ
The name is derived from the term "demilitarized zone", an area between nation states in which military ac-
tion is not permitted.
In computer security, a DMZ (sometimes referred to as a perimeter networking) is a physical or logical sub-
network that contains and exposes an organization's external services to a larger untrusted network, usually
the Internet. The purpose of a DMZ is to add an additional layer of security to an organization's local area
network (LAN). An external attacker only has access to equipment in the DMZ, rather than any other part of
the network.
A31003-H3160-S104-8-7620, 07/2014
glossary.fm
Glossary Nur für den internen Gebrauch
A31003-H3160-S104-8-7620, 07/2014
abbreviations.fm
Abbreviations
Abbreviations 0
ACC Access Point Connection Control

AP Access Point
APE Access Point Emergency
BRI Basic Rate Interface (ISDN S0)
CGW Common Gateway, e.g. HG 3500
CLA Customer License Agent
CLM Customer License Manager
CO Central Office (Deutsche Telekom)
DLS Deployment and License Server
DMC Direct Media Connection (VoIP)
E2E End-to-End
ERH Endpoint Registration Handler
HFA HiPath Feature Access
HMS HiPath Media Server
HSR HiPath Signaling Router
HW Hardware
ICMP Internet Control Message Protocol
IMP IPDA Media Proxy
IPDA IP Distributed Architecture
ISDN Integrated Services Digital Network
JRE Java Runtime Environment
LS Local Survivability
LW Loadware
MEK Master Encryption Key
MXGW Mediatrix Gateway
MTU Maximum Transmission Unit
NAT Network Address Translation
PBX Private Branch Exchange
PEP Proprietary Encryption Protocol (for IPDA signaling)
PSTN Public Switching TDM Network
PXE Preboot eXecution Environment
QDC Quality of Service Data Collection
QoS Quality of Service
SBC Session Border Controller
A31003-H3160-S104-8-7620, 07/2014
abbreviations.fm
Abbreviations
SIP Session Initiation Protocol

SPE Signaling and Payload Encryption
SRSR Small Remote Side Redundancy
SRTP Secure Real Time Protocol
SSA Session Initiation Protocol
TLS Transport Layer Security
VoIP Voice over IP
WBM Web-Based Management
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Nur für den internen Gebrauch List of Figures
List of Figures 0
Figure 1 Packet-by-packet voice transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 2 Jitter: variation of the transmission delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 3 Voice quality depending on delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 4 Jitter buffer functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 5 Difference between static and adaptive jitter buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 6 Settings for the static jitter buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 7 Clock drift in static jitter buffer [transmission quicker than receipt]. . . . . . . . . . . . . . . . . . . . 43
Figure 8 Clock drift in static jitter buffer [transmission slower than receipt] . . . . . . . . . . . . . . . . . . . . 44
Figure 9 Minimum delay for adaptive jitter buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 10 Delay and echo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 11 Delay and hands-free talking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 12 VoIP Bandwidth Reduction Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 13 DMC and Master Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 14 HG 3500 Standby Gateway Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 15 HG 3500 Secondary Gateway Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 16 FPGA - Hardware components involved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 17 HFA infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 18 Sector /cluster definition in one HiPath 4000 node (example) . . . . . . . . . . . . . . . . . . . . . . 169
Figure 19 Resource management for HFA configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Figure 20 Resource management for IPDA configuration with TDM phones . . . . . . . . . . . . . . . . . . . 181
Figure 21 Resource management for IPDA configuration with TDM phones and HFA inaccess point . .
187
Figure 22 Example: Port usage for payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Figure 23 Example: Port usage for signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Figure 24 Example: Port usage for SNMP access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Figure 25 Example: Port usage for diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Figure 1 Topology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Figure 2 LAN interfaces of HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Figure 3 HiPath 4000 Assistant: Loadware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Figure 4 WBM - Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Figure 5 WBM - starte page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Figure 6 WBM - Software Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Figure 7 WBM - Software Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Figure 8 WBM - Software Update: Entering a file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Figure 9 WBM - Software Update: Loading a file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Figure 10 WBM - Software Activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Figure 11 HiPath 4000 SoftGate scenario with Mediatrix gateway - S0 subscriber . . . . . . . . . . . . . . 291
Figure 12 Mediatrix 44xx Gateway (Subs.) - Network -> Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
Figure 13 Mediatrix 44xx Gateway (Subs.) - Network -> Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Figure 14 Mediatrix 44xx Gateway (Subs.) - SIP -> Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Figure 15 Mediatrix 44xx Gateway (Subs.) - SIP -> Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Figure 16 Mediatrix 44xx Gateway (Subs.) - SIP -> Registrations . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Figure 17 Mediatrix 44xx Gateway (Subs.) - ISDN -> Basic Rate Interface . . . . . . . . . . . . . . . . . . . . 295
Figure 18 Mediatrix 44xx Gateway (Subs.) - Telephony -> Call Routing Config 1 . . . . . . . . . . . . . . . 296
Figure 19 Mediatrix 44xx Gateway (Subs.) - Telephony -> Call Routing Config 2 . . . . . . . . . . . . . . . 296
Figure 20 HiPath 4000 SoftGate scenario with Mediatrix gateway - Trunking . . . . . . . . . . . . . . . . . . 297
Figure 21 Mediatrix 44xx Gateway (Trunking) - Network -> Host. . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
List of Figures Nur für den internen Gebrauch
Figure 22 Mediatrix 44xx Gateway (Trunking) - Network -> Interfaces . . . . . . . . . . . . . . . . . . . . . . . 299

Figure 23 Mediatrix 44xx Gateway (Trunking) - SIP -> Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Figure 24 Mediatrix 44xx Gateway (Trunking) - SIP -> Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Figure 25 Mediatrix 44xx Gateway (Trunking) - SIP -> Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Figure 26 Mediatrix 44xx Gateway (Trunking) - SIP -> Registrations . . . . . . . . . . . . . . . . . . . . . . . . 300
Figure 27 Mediatrix 44xx Gateway (Trunking) - ISDN -> Basic Rate Interface . . . . . . . . . . . . . . . . . 301
Figure 28 Mediatrix 44xx Gateway (Trunking) - Telephony -> Call Routing Config 1 . . . . . . . . . . . . 302
Figure 31 HiPath 4000 SoftGate scenario with two Mediatrix gateways . . . . . . . . . . . . . . . . . . . . . . 307
Figure 32 Mediatrix Gateway Trunking - ISDN -> Basic Rate Interface 1 . . . . . . . . . . . . . . . . . . . . . 308
Figure 33 Mediatrix 44xx Gateway Trunking - ISDN -> Basic Rate Interface 2 . . . . . . . . . . . . . . . . 308
Figure 34 Mediatrix 44xx Gateway Trunking - ISDN -> Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
Figure 35 Mediatrix 44xx Gateway Subscriber - -> Basis Rate Interface 1. . . . . . . . . . . . . . . . . . . . 310
Figure 36 Mediatrix 44xx Gateway Subscriber - ISDN -> Status . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
Figure 37 Mediatrix 44xx Gateway Subscriber and Trunking - Telephony -> CODECS . . . . . . . . . . 311
Figure 38 HiPath 4000 SoftGate scenario with Mediatrix 36xx gateway - S2 Interface . . . . . . . . . . 312
Figure 39 Mediatrix gateway 36xx - Network > Host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Figure 40 Mediatrix gateway 36xx - Network > Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Figure 41 Mediatrix gateway 36xx - Network > Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Figure 42 Mediatrix gateway 36xx - SIP > Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Figure 43 Mediatrix gateway 36xx - SIP > Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Figure 44 Mediatrix gateway 36xx - SIP > Registrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Figure 45 Mediatrix gateway 36xx - System > Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
Figure 46 Mediatrix gateway 36xx - ISDN > Primary Rate Interface. . . . . . . . . . . . . . . . . . . . . . . . . 316
Figure 47 Mediatrix gateway 36xx - ISDN > Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Figure 48 Mediatrix gateway 36xx - Call Router > Route Config . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Figure 49 Mediatrix 41xx - Management -> Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Figure 50 Mediatrix 41xx - Network -> Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Figure 51 Mediatrix 41xx - Network -> Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Figure 52 Mediatrix 41xx - Management -> Configuration Scripts . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Figure 53 Mediatrix 41xx - Management -> Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Figure 54 Mediatrix 41xx - SIP -> Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Figure 55 Mediatrix 41xx - SIP -> Registrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Figure 56 Mediatrix 41xx - SIP -> Interop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Figure 57 Mediatrix 41xx - SIP -> Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Figure 58 Mediatrix 41xx - Telephony -> Codecs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Figure 59 Mediatrix 41xx - Telephony -> Codecs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Figure 60 Mediatrix 41xx - Telephony -> Misc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Figure 61 Mediatrix 1204 Gateway - WBM - SIP trunk profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
Figure 62 Mediatrix 1204 Gateway - LAN settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Figure 63 Mediatrix 1204 Gateway - configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Figure 64 Mediatrix 1204 Gateway - Telco analog trunk LS or GS on lines 1 to 4 . . . . . . . . . . . . . . 338
Figure 65 Mediatrix 1204 Gateway - Enable incoming ringing direct to station on line 1 and 4 . . . . 338
Figure 66 Mediatrix 1204 Gateway - Line 1 on incoming call from Telco will ring direct on station 25015
339
Figure 67 Mediatrix 1204 Gateway - Dealy of incoming ringing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Figure 68 Mediatrix 1204 - Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Figure 69 Mediatrix 1204 - Firmware download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Figure 70 Mediatrix 1204 - Managent > Firmware Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
Figure 71 Syslog - System > Syslog > Diagnostic Traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Figure 72 Syslog - System > Syslog > Diagnostic Traces > Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 73 HiPath 4000 SoftGate: Music on hold, announcements. . . . . . . . . . . . . . . . . . . . . . . . . . . 353

Figure 74 Audio file configuration with HiPath 4000 SoftGate WBM . . . . . . . . . . . . . . . . . . . . . . . . . 356
Figure 75 Interworking with Microsoft Lync Communications Server 2010 over Mediation Server . . 359
Figure 76 Microsoft-Lync - SIP trunk profile parameter for vHG 3500 . . . . . . . . . . . . . . . . . . . . . . . . 364
Figure 77 Microsoft-Lync - SIP trunk profile configuration for vHG 3500 . . . . . . . . . . . . . . . . . . . . . . 365
Figure 78 Micorosft Lync Server - Define new IP/PSTN gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
Figure 79 Micorosft Lync Server - Properties for new IP/PSTN gateway . . . . . . . . . . . . . . . . . . . . . . 367
Figure 80 Micorosft Lync Server - Mediation pool properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
Figure 81 Micorosft Lync Server - PSTN gateway properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
Figure 82 Micorosft Lync Server - Assign gateway to Mediation Server . . . . . . . . . . . . . . . . . . . . . . 368
Figure 83 Micorosft Lync Server - Publish the changes to the Micorosft Lync Server topology. . . . . 369
Figure 84 Micorosft Lync Server - Define dial plan rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
Figure 85 Micorosft Lync Server - Create voice policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Figure 86 Micorosft Lync Server - Create new PSTN usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Figure 87 Micorosft Lync Server - Assign a route to the PSTN usage . . . . . . . . . . . . . . . . . . . . . . . . 370
Figure 88 Micorosft Lync Server - Assign the HiPath 4000 gateway to the route . . . . . . . . . . . . . . . 371
Figure 89 Micorosft Lync Server - Define the trunk configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Figure 90 HFA gatekeeper redundancy "simple" mode - Normal status . . . . . . . . . . . . . . . . . . . . . . 374
Figure 91 HFA gatekeeper redundancy "simple" mode - Failure of HiPath 4000 SoftGate 18 . . . . . 375
Figure 92 HFA gatekeeper redundancy "mixed" mode - Normal status . . . . . . . . . . . . . . . . . . . . . . . 375
Figure 93 HFA gatekeeper redundancy "mixed" mode - Failure of HiPath 4000 SoftGate 18 . . . . . . 376
Figure 94 HFA gatekeeper redundancy "mixed" mode - Failure of HiPath 4000 SoftGate 20 . . . . . . 376
Figure 95 OpenStage - Subscriber Redundancy - Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Figure 96 OpenStage - Subscriber Redundancy - Standby Gateway . . . . . . . . . . . . . . . . . . . . . . . . 380
Figure 97 OpenStage - Activate Subscriber Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
Figure 98 optiPoint - Subscriber Redundancy - Gateways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
Figure 99 optiPoint - Activate Subscriber Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Figure 100 Survivable HiPath 4000 SoftGate - Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
Figure 101 Survivable HiPath 4000 SoftGate - IT network failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
Figure 102 Survivable HiPath 4000 SoftGate - Call control failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
Figure 103 IPv6 for HiPath 4000 SoftGate (trunking) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
Figure 104 IPv6 address for vHG 3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Figure 105 Options for IPv6 gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Figure 106 Status of IPv6 gateway (restart required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
Figure 107 Status of IPv6 gateway (confirmed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
Figure 108 IP mode of an IPv6 trunking gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Figure 109 SDP negotiation in DualStack mode of an IPv6 trunking gateway . . . . . . . . . . . . . . . . . . . 393
Figure 110 IPv6 address of an IPv6 trunking gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Figure 111 SIP trunk profile parameter for IPv6 trunking partner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Figure 112 SIP trunk profile for IPv6 trunking partner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Figure 113 Status of SIP trunk profile for IPv6 trunking partner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Figure 114 IPv6 for HiPath 4000 SoftGate (internal connectivity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Figure 115 NGS - Administration/configuration of IPv6 addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Figure 116 NGS - Confirming IPv6 addresses manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Figure 117 NGS database: Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
Figure 118 NGS database: Export file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
Figure 119 NGS database: Save export file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
Figure 120 NGS database: Import with warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Figure 121 NGS database: Import failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Figure 122 NGS database: Data backup/restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Figure 123 NGS database: System backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Figure 124 Activating the SIP Load Balance server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 125 Activating SIP Load Balancing of gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406

Figure 126 SIP Load Balancer trunk profile parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
Figure 127 SIP Load Balancer trunk profile parameter for OpenScape UC Media Server . . . . . . . . . 408
Figure 128 OpenScape UC Media Server farm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
Figure 129 Media Server configuration for SIP Load Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
Figure 130 SIP Load Balancer status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Figure 131 SIP Load Balancer status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Figure 132 Secure IP connectivity for remote offices over the Internet. . . . . . . . . . . . . . . . . . . . . . . . 413
Figure 133 Secure IP connectivity for remote offices with Mobile HFA. . . . . . . . . . . . . . . . . . . . . . . . 414
Figure 134 Secure IP connectivity for remote offices with gatekeeper redundancy . . . . . . . . . . . . . . 414
Bild 135 DMZ scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
Bild 136 DMZ scenario - Required ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
Bild 137 DCMP configuration for Secure Remote Subscriber. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
Bild 138 Configuring the DLS for the DCMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
Bild 139 Testing the DLS/DCMP configuration with an IP terminal in the remote office . . . . . . . . . 425
Bild 140 DCMP - List Entries menu before the IP terminal has fetched the Contact-Me job from the
DCMP 426
Bild 141 DCMP - List Entries menu after the IP terminal has fetched the Contact-Me job from the DCMP
426
Figure 142 Secure IP connectivity for remote subscribers - Sample generation . . . . . . . . . . . . . . . . 427
Bild 143 Secure Remote Subscriber - HiPath 4000 SoftGate WAN settings . . . . . . . . . . . . . . . . . 427
Bild 144 Secure Remote Subscriber - HiPath 4000 SoftGate SPE certificate . . . . . . . . . . . . . . . . 428
Figure 145 Direct picture retrieval configuration in HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . 433
Figure 146 Indirect picture retrieval configuration in HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . 434
Figure 147 Canonical dial settings for picture retrieval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
Figure 148 Picture retrieval configuration via DLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
Figure 149 LDAP server - HiPath 4000 SoftGate data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
Figure 150 LDAP server - Telephone contact data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
Figure 151 LDAP server - Example of direct picture retrieval (01) . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
Figure 152 LDAP server - Example of direct picture retrieval (02) . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Figure 153 Launching the LDAP server access test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Figure 154 Searching for phone numbers using the LDAP server . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Figure 155 Correctly configured LDAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
Figure 156 Incorrectly configured LDAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
Figure 157 MFC-R2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
Figure 1 Management LAN Interface at HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
Figure 1 Example: IP trunking in an HiPath 4000 networked system. LEGK is active in each node. . . .
463
Figure 2 Configuring a HG 3500 gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
Figure 3 Example for sector path description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
Figure 1 Typical HG 3500 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
Figure 2 HFA infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
Figure 3 Technical relationship between UP0e and HFA user connection . . . . . . . . . . . . . . . . . . . 510
Figure 4 A user registers at another HFA phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Figure 5 Configuration Management - System Data - Board - CGW Function Block - View Object 515
Figure 6 Configuration Management - System Data - Board - CGW Function Block - View Object List.
516
Figure 7 Configuration Management - System Data - Board - CGW Function Block - Configure new
Function block 516
Figure 8 Configuration Management - System Data - Board - Board . . . . . . . . . . . . . . . . . . . . . . . 517
Figure 9 Configuration Management - System Data - Board - Board - STMI2-IGW Board Data tab 518
Figure 10 Configuration Management - System Data - Board - Board - STMI Board Data tab . . . . 518
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 11 Configuration Management - System Data - Board - Board - STMI Feature Access tab . . 519
Figure 12 Configuration Management - Station - Station - Basic 1 tab . . . . . . . . . . . . . . . . . . . . . . . 519
Figure 1 Activation of feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 534
Figure 2 Call to mobile user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 534
Figure 3 Call to visited phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
Figure 1 Overview of architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
Figure 2 Signaling for an internal access point call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561
Figure 3 Voice link (payload) for an internal access point call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562
Figure 4 Signaling for an access point  access point call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562
Figure 5 Voice link (payload) for an access point  access point call . . . . . . . . . . . . . . . . . . . . . . . 563
Figure 6 Signaling for an access point  central system call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
Figure 7 Voice link (payload) for an access point  central system call . . . . . . . . . . . . . . . . . . . . . 564
Figure 8 Trunk Access/Networking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564
Figure 9 Survivability: failure in the IP network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
Figure 10 Signaling survivability examples: Signaling via PSTN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566
Figure 11 Payload survivability: Alternative route for the payload via PSTN . . . . . . . . . . . . . . . . . . . 566
Figure 12 HiPath 4000 LAN segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
Figure 13 Difference between “networked“ and “direct link“ access point . . . . . . . . . . . . . . . . . . . . . 591
Figure 14 Configuring a “networked“ access point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592
Figure 15 Configuring a “Direct Link“ access point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Figure 16 Internal address assignment of a “direct link“ access point . . . . . . . . . . . . . . . . . . . . . . . . 601
Figure 17 AP 3500 IP - front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623
Figure 18 Configuring a HG 3500 for IPDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626
Figure 19 Tie connections are not permitted within a system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
Figure 20 Classmarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
Figure 21 Special routes between access points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
Figure 22 Special routes between access point and HiPath 4000 LAN segment. . . . . . . . . . . . . . . . 642
Figure 23 Signaling connection with/without bandwidth restriction. . . . . . . . . . . . . . . . . . . . . . . . . . . 652
Figure 24 Source-dependent routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
Figure 25 Interaction between LDPLN and LPROF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666
Figure 26 Blocks the IP connection for payload due to „Bad Quality“ . . . . . . . . . . . . . . . . . . . . . . . . 670
Figure 27 Payload survivability - source dependent routing configuration . . . . . . . . . . . . . . . . . . . . . 674
Figure 28 Payload survivability and networking - normal route A calls B or B calls A . . . . . . . . . . . . 682
Figure 29 Payload survivability and networking - survivability route A calls B . . . . . . . . . . . . . . . . . . 683
Figure 30 Payload survivability and networking - survivability route B calls A . . . . . . . . . . . . . . . . . . 683
Figure 31 Divert call in survivability mode - User scenario 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
Figure 35 Routes for music on hold: Supply in the central system. . . . . . . . . . . . . . . . . . . . . . . . . . . 701
Figure 36 Routes for music on hold: Supply in access point 17 - local subscriber. . . . . . . . . . . . . . . 702
Figure 37 Routes for music on hold: Supply in access point 17 - central subscriber . . . . . . . . . . . . . 702
Figure 38 Routes for music on hold: Supply in access point 17 - subscriber in different AP . . . . . . . 703
Figure 41 Change of address in “networked“ access points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708
Figure 42 Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
Figure 43 Feature overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717
Figure 44 IPDA Wizard - Start page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769
Figure 45 IPDA Wizard - Graphical overview of the currenct IPDA configuration . . . . . . . . . . . . . . . 771
Figure 1 LAN scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 785
Figure 2 LAN/WAN scenario. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 786
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 3 Branch (WAN) scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787

Figure 4 AP Emergency scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788
Figure 5 HiPath 4000 Assistant Backup & Restore: configuring an AP backup server . . . . . . . . . . 822
Figure 6 HiPath 4000 Assistant Backup & Restore: Creating a schedule for the backup . . . . . . . . 824
Figure 7 HiPath 4000 Assistant Backup & Restore - Select “Log Files“ . . . . . . . . . . . . . . . . . . . . . 827
Figure 8 HiPath 4000 Assistant Backup & Restore - Status of Host and CC-APs . . . . . . . . . . . . . 827
Figure 9 HiPath 4000 Assistant Backup & Restore: Creating a schedule for the configuration data
backup 829
Figure 10 Configuring the system ID apeftp in the host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844
Figure 11 Configuring the AP backup server in the host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845
Figure 12 Checking the backup status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845
Figure 13 LAN wizard - Selecting the deployment for AP Emergency installation . . . . . . . . . . . . . . 846
Figure 14 LAN wizard - Entering the customer LAN and IPDA LAN addresses . . . . . . . . . . . . . . . . 847
Figure 15 LAN wizard - Send AMO initialization commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 847
Figure 16 Configuring the IPDA shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
Figure 17 Configuring the apeftp system ID in the CC-AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
Figure 18 Configuring the AP backup server in the CC-AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849
Figure 19 Checking the backup status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849
Figure 1 Example: HiPath 4000 system in Houston with external telephones in Los Angeles and New
York 855
Figure 1 Supervisory message flow for signaling survivability in the CC . . . . . . . . . . . . . . . . . . . . 871
Figure 2 Message flow for signaling survivability in the access point/HiPath 4000 SoftGate . . . . . 872
Figure 3 IPDA with signaling survivability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873
Figure 4 Signaling Survivability über alternatives LAN und L2 Redundanz . . . . . . . . . . . . . . . . . . 875
Figure 5 Signaling Survivability über alternatives LAN und zweiter Ethernet-Schnittstelle . . . . . . . 875
Figure 6 Signaling survivability via Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
Figure 7 Survivability router configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
Figure 8 Survivability router configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
Figure 9 Signaling survivability withWAML replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
Figure 10 WAML replacement - Second LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890
Figure 11 WAML replacement - PSTN global data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 891
Figure 12 WAML replacement - PSTN peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 892
Figure 13 WAML replacement - PSTN station number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
Figure 14 WAML replacement - Static route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
Figure 15 Signaling survivability without WAML replacement but with a router . . . . . . . . . . . . . . . . 894
Figure 16 Signaling Survivability via alternate LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896
Figure 17 Signaling Survivability LAN interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
Figure 1 SIP session timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
Figure 2 SIP subscriber as a part of an ONS group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 919
Figure 3 SIP Peer Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927
Figure 4 Remote Agent Server connectivity via SIP trunking interface. . . . . . . . . . . . . . . . . . . . . . 946
Figure 5 Activating SIP trunk profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
Figure 6 Example of a standard profile: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951
Figure 7 Add Account/Authentication (Example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 952
Figure 8 Security configuration for SIP-Q trunk profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
Figure 9 Security configuration for SIP-Q trunk profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
Figure 10 Activated SIP trunk profile (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
Figure 11 Account/authentication data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 955
Figure 12 SIP trunk profile of a provider with registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956
Figure 13 Activated SIP trunk profile (with registration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 957
Figure 14 SIP trunk profile of a provider without registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 958
Figure 15 Activated SIP trunk profile (without registration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 959
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 16 SIP-Q trunk profile with registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 960

Figure 17 Activated SIP-Q trunk profile with registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 961
Figure 18 SIP-Q trunk profile without registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962
Figure 19 Activated SIP-Q trunk profile without registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963
Figure 20 SIPconnect reference architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
Figure 21 HG 3500 direct to SIP carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
Figure 22 SIP service profiles in HG 3500 WBM (scenario 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970
Figure 23 SIP service profiles in HG 3500 WBM (scenrario 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970
Figure 24 HG 3500 via session border controller to SIP carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971
Figure 25 SIP Service Profiles in HG 3500 WBM (scenario 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
Figure 26 SIP Service Profiles in HG 3500 WBM (scenario 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
Figure 29 Configuration example: both nodes are LEGK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978
Figure 1 Activation of DTMF outband signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
Figure 2 Configuration example: both nodes are LEGK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1008
Figure 1 Encrypted signaling and payload connections HiPath 4000 V6 . . . . . . . . . . . . . . . . . . . . 1030
Figure 2 Encrypted signaling and payload connections HiPath 4000 SoftGate . . . . . . . . . . . . . . . 1031
Figure 3 Public Key Infrastructure (PKI) using the example of common gateways . . . . . . . . . . . . 1032
Figure 4 Signaling encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033
Figure 5 Time interval for re-keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034
Figure 6 Voice Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035
Figure 7 MIKEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
Figure 8 RTP security mode on the vHG3500 for a SIP-Q trunk . . . . . . . . . . . . . . . . . . . . . . . . . . 1038
Figure 9 SIP trunking security mode for a native SIP trunk profile with SPE . . . . . . . . . . . . . . . . . 1039
Figure 10 SIP trunk profile, SIP-Q, security parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054
Figure 11 SIP trunk profile, native SIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054
Figure 12 HiPath 4000 SoftGate and SPE - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
Figure 13 Loading the Secure Trace certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1083
Figure 14 SPE root certificate generation (no SPE root certificate exists) . . . . . . . . . . . . . . . . . . . . 1092
Figure 15 SPE root certificate generation with existing SPE root certificate . . . . . . . . . . . . . . . . . . 1093
Figure 16 Download of SPE root certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1094
Figure 17 SPE certificate generation (no SPE certificate exists) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1096
Figure 18 SPE certificate generation with existing SPE certificate. . . . . . . . . . . . . . . . . . . . . . . . . . 1097
Figure 19 Displaying/Downloading of SPE certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1098
Figure 20 Importing a SPE CA certificate for SIP trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120
Figure 21 Importing a SPE certificate for SIP trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120
Figure 22 Importing a SPE certificate for HFA subscriber at vHG 3500. . . . . . . . . . . . . . . . . . . . . . 1121
Figure 23 Creating a Virtual Device / IP Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124
Figure 24 Scanning an IP Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124
Figure 25 IP Gateway "scanned" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125
Figure 26 Preparing Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125
Figure 27 Time Server Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126
Figure 28 Issuer: Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126
Figure 29 Issuer: Administration > Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126
Figure 30 CA Administration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
Figure 31 Activate Voice Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
Figure 1 DMC in connection with HFA subscriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151
Figure 2 HG 3500 subscriber which functions as a DMC proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . 1152
Figure 1 HiPath 4000 Softgate - HiPath 4000 host system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1183
Figure 2 Fax between SMP enabled endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1183
Figure 3 Media routing in IPV6 scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1184
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOF.fm
Figure 4 Media Relay scenario with DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1184

Figure 1 Recorder interface assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1201
Figure 2 Second headset port assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1201
Figure 3 Microphone/loudspeaker port assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1202
Figure 4 Headset port assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1203
Figure 5 Contact port assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1204
Figure 6 Key layout: optiPoint 420 advance and optiPoint 420 key module . . . . . . . . . . . . . . . . . 1212
Figure 7 HFA (IP) terminal with plug-in power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213
Figure 8 HFA (IP) terminal with PowerHub power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214
Figure 9 PC and HFA station with “single wire to the desk“ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214
Figure 10 optiPoint and USB for Simple Dialer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1215
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOT.fm
Nur für den internen Gebrauch List of Tables
List of Tables 0
Table 1 Example: Class B IP address, netmask and network address . . . . . . . . . . . . . . . . . . . . . . 34

Table 2 Voice quality depending on delay and packet loss rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 3 TOS values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4 TOS byte correspondences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 5 Bandwidth for active DMC master connections without SPE . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 6 Bandwidth for active DMC master connections with SPE . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 7 Bandwidth for master connections no longer used (without SPE) . . . . . . . . . . . . . . . . . . . . 60
Table 8 Bandwidth for master connections no longer used (with SPE). . . . . . . . . . . . . . . . . . . . . . . 60
Table 9 Number of B channels dependent on enabled features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 10 Number of B channels depending on SPE and DMC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 11 Networking with HiPath 4000 V6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 12 WBM rights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Table 13 WBM rights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Table 14 Data in the standard MIB-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Table 15 Data in the SNI specific MIB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Table 16 Definitions in the company’s specific MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Table 17 Collected list of traps (repeated). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Table 1 HiPath 4000 SoftGate advantages compared with existing branch scenarios . . . . . . . . . . 282
Table 1 AMO ZANDE parameters in the CHANGE branch under TYPE=ALLDATA . . . . . . . . . . . 471
Table 2 AMO BFDAT parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
Table 3 AMO BCSU parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481
Table 4 AMO CGWB parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
Table 5 AMO CGWB parameters in the CHANGE branch under MTYPE=CGW, TYPE=GWDATA . .
485
Table 6 AMO CGWB parameters in the CHANGE branch under MTYPE=CGW, TYPE=LEGKDATA.
486
Table 7 AMO CGWB parameters in the CHANGE branch under MTYPE=CGW, TYPE=DMCDATA .
488
Table 8 AMO CGWB parameters in the CHANGE branch under MTYPE=CGW, TYPE=GLOBIF. 489
Table 9 AMO CGWB parameters in the CHANGE branch under MTYPE=CGW, TYPE=GKDATA 490
Table 10 AMO SIPCO parameters in the CHANGE branch under TYPE=BANDW . . . . . . . . . . . . . 504
Table 11 AMO SIPCO parameters in the DISPLAY branch under TYPE=BANDW . . . . . . . . . . . . . 505
Table 12 AMO SIPCO parameters in the DISPLAY branch under TYPE=BANDW . . . . . . . . . . . . . 505
Table 1 AMO SIPCO parameters in ADD branch or for CHANGE under TYPE=LSNET . . . . . . . . 576
Table 2 AMO SIPCO parameters in CHANGE branch under TYPE=DIFFSERV . . . . . . . . . . . . . . 581
Table 3 AMO SIPCO parameters in CHANGE branch under TYPE=TIMING. . . . . . . . . . . . . . . . . 584
Table 4 AMO SIPCO parameters in CHANGE branch under TYPE=PLQUAL . . . . . . . . . . . . . . . . 588
Table 5 AMO SIPCO parameters in CHANGE branch under TYPE=DMCDATA . . . . . . . . . . . . . . 589
Table 6 APNW: AMO UCSU parameters in ADD branch under TYPE=AP . . . . . . . . . . . . . . . . . . 594
Table 7 APNW: AMO APRT parameters in ADD branch under TYPE=APNET . . . . . . . . . . . . . . . 598
Table 8 APNW: AMO UCSU parameters in ADD branch under ART=AP. . . . . . . . . . . . . . . . . . . . 603
Table 9 APDL: AMO APRT parameters in ADD branch under TYPE=APNET . . . . . . . . . . . . . . . . 609
Table 10 Basic initialization parameters for “networked“ access points . . . . . . . . . . . . . . . . . . . . . . 615
Table 11 Basic initialization parameters for “direct link“ access point . . . . . . . . . . . . . . . . . . . . . . . . 615
Table 12 IPDA classmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
Table 13 Classmark handling for EC or VAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
Table 14 Classmark handling for codec type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
A31003-H3160-S104-8-7620, 07/2014
ip_solutionsLOT.fm
List of Tables Nur für den internen Gebrauch
Table 15 Communication matrix for special routes between access point and HiPath 4000 LAN
segment” 646
Table 16 AMO APRT parameters in CHANGE branch under TYPE=ROUTTBL. . . . . . . . . . . . . . . 647
Table 17 AMO LPROF parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667
Table 18 AMO APRT parameters in ADD branch under TYPE=ALTROUT . . . . . . . . . . . . . . . . . . 679
Table 19 Change of address in “networked“ access points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
Table 20 Address change in HiPath 4000 LAN segment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
Table 21 Access point-specific configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718
Table 22 Load calculation for an RTP connection (VoIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
Table 23 Overhead with RTP connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
Table 24 Load for an RTP connection [Kbps]- by stack layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724
Table 25 Load on an RTP connection [kbps] with VAD during inactivity . . . . . . . . . . . . . . . . . . . . . 725
Table 26 Load calculation for an RTCP connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725
Table 27 High-priority load of an access point (G.711/20 ms sample size) . . . . . . . . . . . . . . . . . . . 726
Table 28 High-priority load of an AP as a function of codec and sample size . . . . . . . . . . . . . . . . . 727
Table 29 High-priority load of an AP as a function of the permissible B-channels. . . . . . . . . . . . . . 728
Table 30 High-priority load of a HG 3500 (G.711/20 ms sample size). . . . . . . . . . . . . . . . . . . . . . . 732
Table 31 High-priority load of a HG 3500 as a function of codec and sample size . . . . . . . . . . . . . 732
Table 32 High-priority load of a HG 3500 as a function of the permissible number of B-channels . 733
Table 33 Configuring Ethernet MAC frames for IPDA payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
Table 34 Configuring IP frames for IPDA payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
Table 35 CLI parameter for “networked“ access point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742
Table 36 CLI parameters for “direct link“ access point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
Table 37 Assignment of parameter names in LW-CLI to the AMO parameters . . . . . . . . . . . . . . . . 745
Table 1 Configuration parameters derived for the CC-AP/Survivable HiPath 4000 SoftGate . . . . 796
Table 2 AMO APESU parameters in ADD or CHANGE branch under DATA=CCAP . . . . . . . . . . 798
Table 3 AMO APESU parameters in ADD or CHANGE branch under DATA=APEGRP. . . . . . . . 801
Table 4 AMO APESU parameters in ADD or CHNAGE branch under DATA=AP . . . . . . . . . . . . . 805
Table 5 The AP Emergency-specific parameter APESWDLY of the AMO SIPCO in CHANGE branch
under TYPE=TIMING 811
Table 6 AMO APESU parameter in the EXEC branch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 816
Table 7 Input fields in the HiPath 4000 Assistant Backup & Restore schedule . . . . . . . . . . . . . . . 824
Table 8 Schedule input fields for the configuration data backup . . . . . . . . . . . . . . . . . . . . . . . . . . 830
Table 1 AMO APRT parameters in ADD branch under TYPE=SURV, CONF=ROUTER . . . . . . . 905
Table 2 AMO APRT parameters in ADD branch under TYPE=SURV, CONF=AP . . . . . . . . . . . . 905
Table 3 AMO UCSU parameter in ADD/CHANGE branch under UNIT=AP . . . . . . . . . . . . . . . . . 906
Table 1 SIP subscriber communication matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
Table 2 Trunking communication matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907
Tabelle 3 Supported RFCs (Request for Comments) for SIP interfaces . . . . . . . . . . . . . . . . . . . . . 908
Table 4 Protocols in the AMOs CGWB and GKREG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
Table 1 Protocols in the AMOs CGWB and GKREG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
Table 1 Signaling and payload encryption (IP environment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031
Table 2 Possible encryption depending on the connection type and gateway. . . . . . . . . . . . . . . 1038
Table 3 Connection to Gateway Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1044
Table 4 Secure trace possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1080
Table 1 Recommended ASC settings in AMO CGWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1135
A31003-H3160-S104-8-7620, 07/2014
Index
Index
Index
Software update 792

19" AP 3500 access point 625 Spreadsheets-configuration 833
19" HiPath AP 3500 access point 623 Startup
CC-AP 818
A Survivable HiPath 4000 SoftGate 818
Access point 591, 600, 611, 612, 614, 617, 741 Survivability Unit in AP 3700 IP 788
Access Point Emergency 784 Survivability Unit on HiPath 4000 SoftGate 788
Access point parameters, changing 611 Switchover delay 810
Activating the SPE feature 1066 Switchover in emergency mode 789
Adapter for optiPoint Telephones 1211 Switchover to normal operation 791
announcements per access point 717 Time synchronization 561, 793
AP Emergency 784 Time synchronization between host system and
Acceptance of AP Emergency configuration 818 CC-AP 817
Administration switchover of access points 814 Time synchronization between host system and
Administration switchover of HiPath 4000 Survivable HiPath 4000 SoftGate 817
SoftGates 814 verify AP Emergency configuration 818
Allocating access points to a survivability unit 789 APE 784
Application support in emergency mode 794 Architecture 51
Configuration 795 Average data delay (ms) (parameter) 46
Configuration data 792 Average voice delay (ms) (parameter) 46
configure access point 804
configure Backup & Restore on CC-AP 827 B
configure Backup & Restore on Survivable HiPath Bandwidth Requirements 58
4000 SoftGate 827 Boards 1195
configure CC-AP 796
C
configure emergency group 798
Call scenarios 561
configure HiPath 4000 SoftGate 804
Changing the login and password for WBM/CLI 201
configure Survivable HiPath 4000 SoftGate 796
Circuit switching 560
Connection between subsystems (islands) 792
CLI HG 3500 195
Connection data 811
CLI HG3500
delete CC-AP 798
access control 196
delete emergency group 803
DLS 199
delete entire AP Emergency configuration 808
gateway setup 196
Display on terminal 809
general information 195
FAQs - Frequently Asked Questions 853
general operations 195
Feature description 784
handling images/file 197
HiPath 4000 Backup & Restore 821
maintenance 197
HiPath 4000 in customer LAN 795
SSL 199
Information for network administrators 837
CMI 706
Licensing 794
CO trunk circuits in access points 631
modify CC-AP 796
Codec standards 36
modify emergency group 798
Command Line Interface CLI in HG 3500 195
modify Survivable HiPath 4000 SoftGate 796
Configuration in HiPath 4000 (Example) 1227
Normal operation 791
Configuring an access point 591
Quick guide 839
removing access points 808
Scenarios 784
A31003-H3160-S104-8-7620, 07/2014
Index
D Goal of this document 31

Data connections (Mediatrix 44xx) 306 Guidelines for Installing an IP Feature 467
Default security level 1050
Delay and Echo 47
H
H323 / H323 Annex connectivity 1003
Delay and Hands-Free Talking 48
H323 connectivity
Deleting All Devices Assigned a Station Number at the
Overview 1003
IP Port 1221
Hardware 284
Deleting an access point 612
HFA phone at another HiPath 4000 1159
Deleting IP Telephone Adapters 1221
HFA phone at HiPath 3000 1161
Deleting NV Services at the IP Port 1221
HG 3500 31
Deleting the IP Telephone’s Key Module 1221
B channels dependent on enabled features 62
Deletion 1221
exchanging modules 70
Different announcements per access point 569
HG 3500 as HG3570 in the HiPath 4000 system 626
Different MFV dial tone receiver per access point 569
HG 3500 V4
Different Time Zones 855
DLS client bootstrapping 123
Different Time Zones (DTZ) 568, 855
HG 3575 31, 618, 622
Different tones per access point 569
HG3500
Direct link access point 600
load concept 89
Distributing certificates with DLS 1099
HiPath 4000 Assistant
DMC 61, 1034
Configure Common Gateway HG 3500 989, 1017
HFA station on HiPath 4000 1158
delete IPGW 991, 1020
SIP station on HiPath 4000 1154
modify board data of IPGW 991, 1020
DTMF dial tone receivers per access point 717
HiPath 4000 SoftGate 277
DTMF Outband Signaling 1005
HiPath Cordless IP 1223
E HiPath Feature Access - Standby Board HG 3500 107
Encoding 58 HiPath Feature Access (HFA) 507
Example
Two HFA subscriber at different systems 548
I
Information for Network Administrators 763
Two HFA subscribers in the same Host 547
Information on exchanging 3575 HG boards 622
External Music on Hold 701
IP address changes 707
F IP Distributed Architecture (IPDA) 559
FAQs - Frequently Asked Questions 773 IP Overhead 59
Fax transmission and detection 35 IP ports 263
Fax/Modem over IP 35 IP Terminal Generation 1213
Feature Description 1029, 1223 IP terminals 1193
Feature description 559 IP trunk configuration for SPE 1053
Feature description Mobility session 533 IPDA 559, 1068, 1069
Features 79, 278 IPDA configuration 571
FMoIP 35 IPDA-Different Time Zones
Frequently Asked Questions 529 Assigning the Time Classes to an AP Shelf 862
Assigning the Time Classes to an HFA Station 862
G Changing the System Date/Time with AMO
Gatekeeper Function 464 DATE 865
Gatekeeper Redundancy for HFA Subscriber 373 Configuring the Time Classes 860
Gatekeeper Restrictions 465 Deleting a Time Class 863
Gateways HG 3500 and HG 3575 31 Deleting the Daylight Savings Time
Gateways-Communication Matrix 87 Changeover 864
General Configuration Rule 1211 Feature Description 855
General Information 463 Generation Example 859
Generation Mobility session 547 Relevant AMOs 867
A31003-H3160-S104-8-7620, 07/2014
Index
Service Information 857 O

ISDN S0 data (Mediatrix 44xx) 306 OpenStage IP Terminals 1205
optiPoint Acoustic Adapter Data 1202
J optiPoint IP Terminals 1197
Jitter buffer type (parameter) 46
optiPoint Recorder Adapter Data 1200
K Overview 277, 463, 507
Key Layout on optiPoint Telephones 1212 P
Key words 33
Packet loss/delay preference (parameter) 46
L Payload - DMC authorization 1144
Large Enterprise Gatekeeper (LEGK) 463 Payload - Domains 1146
LEGK 463 Payload - Feature activation while DMC is active 1144
Link status display 986, 1016 Payload - Feature Description 1131, 1133
Load Balancing 403 Payload - Features with DMC 1143
Load calculation 723 Payload - Generation 1144
Loading new loadware on a HG 3575 618 Payload - H.323 stack on IPDA boards 1146
Local Access Point Administration at CLI via Payload - Maximum number of DMC connections on IP
Terminal 741 boards 1145
Local Configuration of an access point 614 Payload - Relevant AMOs 1148
Payload - Service Information 1143
M Payload - Voice Activity Detection (VAD) 1145
Master Encryption Key 1069 Payload survivability 669
Maximum data delay (ms) (parameter) 46 Power Requirements 51
Maximum voice delay (ms) (parameter) 46 Prerequisites 51
Mediatrix 1204 gateway 329 Protocol 263
Mediatrix 41xx gateway 321
Mediatrix 44xx gateway R
scenario 291, 297, 306 Reference clock in access point 617
Mediatrix 44xx gateway (data) 306 Required Bandwidth per Connection 59
Mediatrix 44xx gateway voice 290, 297 Requirements 1050
Mediatrix gateways - configuration notes 289 Resource Management 84
MEK 1069 Restrictions 1041, 1079
Microsoft Lync Communication Server RG 8300 V6 459
interworking 359 Runtime and noticeable effects 47
Mobile HFA Logon 533 S
Mobility session 533
Sampling Time 58
Modem transmission and detection 35
Secure trace configuration 1079
Modules for optiPoint Telephones 1211
Security 83
MOH 353
Service Information 1211, 1225
Music on Hold 353
Service information 1041
Music on hold 701
Service information Mobility session 543
N Services 263
Native SIP Shared Desk Area 535
codecs 947 Signaling and payload encryption (SPE) 1029
Relevant AMOs 986, 1016 Signaling and payload encryption (SPE)
Network administrators 763 configuration 1049
Network data 52 Signaling and Payload Separation 567
Network Requirements 51 Signaling and Payload Separation (SPS) 685
Networked access point 592 Signaling survivability 650, 869
SIP Carrier 965
SIP connectivity
A31003-H3160-S104-8-7620, 07/2014
Index
Boards used 911 Voice Quality 37

Overview 907
SIP subscriber communication matrix 907 W
SIP trunking communication matrix 907 WBM 286
SIP phone at another HiPath 4000 1155, 1156 Web-Based Management 1119
SIP phone at HiPath 3000 1157
SIP Service Provider 965
SIP Subscriber
change 931
configure 930
display 932
Enabling/Disabling DMC 931
Registered SIP subscriber 932
Relevant AMOs 933
remove 931
Service Information 914
unregistered SIP subscribers 932
SIP-Q
trunking between HiPath 4000 and OpenScape
Voice with SIP-Q V2 992
SoftGate upgrade 285
Source-dependent routing 664
SPE configuration at the IP terminal 1063
SPE:external gateway configuration 1053
Special routes 639
Spreadsheets - IPDA configuration 747
STMI2/4 Board Configuration 929
Subscriber gateway (Mediatrix 44xx) 309
Subscriber trunk circuits in access points 631
Supported IP Terminals 1193
System capacity 560
System Requirements 51
T
TDM phone at another HiPath 4000 (remote
shelf) 1163
TDM phone at another HiPath 4000, connected via
H323 trunking 1164
TDM phone at HiPath 3000 1166
Terms 33
Tie trunk circuits in access points 631
tones per access point 717
Traffic Considerations 66
Trunking gateway (Mediatrix 44xx) 307
U
User interface Mobility session 539
V
VAD 61, 81
Voice Activity Detection (VAD) 61
Voice encryption devices 50
A31003-H3160-S104-8-7620, 07/2014

HiPath 4000 V6 - Section 4 - IP Solutions - Service Documentation - Issue 8

Uploaded by

Copyright:

Available Formats

HiPath 4000 V6 - Section 4 - IP Solutions - Service Documentation - Issue 8

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HiPath 4000 V6 - Section 4 - IP Solutions - Service Documentation - Issue 8

Uploaded by

Copyright:

Available Formats

HiPath 4000 V6 

HiPath 4000 V6 - IP Solutions - Contents

Highlights and Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.1.3 Feature Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

12 Gateway HG 3575 - Changing Parameters with AMO STMIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

16.4 Configuring SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

19 Command Line Interface CLI at HG 3575 V4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

3.3.5 Analog Stations (Mediatrix 41xx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321

9.3 Generation (Example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

14.3.1 HiPath 4000 SoftGate configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

3.8 Configuring Circuits and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503

1 IPDA Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559

2.7.6.4 F8291 - Net Weakness End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662

5 Spreadsheets - IPDA Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747

2.14.3 Survivable HiPath 4000 SoftGate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 818

2 Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877

3 SIP Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939

4.5.4 Configuration in the Session Border Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976

1.3.3 Voice Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035

4 Secure Trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1079

Payload Switching DMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1131

HiPath Cordless IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1223

Highlights and Hints

Highlights and Hints

– Bit Rate: Auto negotiate is fully supported as of Senta version 12.

– Update for parameter TYP=SIGQOS (see Section 12.11, “TYPE SIGQOS

– Note regarding the use of trunking protocols in connection with multiple

– Update in Section 21.4.2, “Signaling”.

– New paragraph regarding IP Interface MTU (see Section 3.3, “Network

– Updates regarding Short Hold in Section 3.1.3.3, “Signaling Survivability

– Note regarding HiPath 4000 SoftGate in connection with signaling

– Update for feature “HSR via UDP”.

• IP Distributed Architecture (IPDA)

– Signaling and Payload Separation: The restriction concerning ACD

– Enhancements in Section 2.11, “Divert Call in Survivability Mode to

– Payload Survivability: Restriction using VNR and payload survivability

• Access Point Emergency

– Enhanced information to the switchover delay time (see Section 2.10,

– New information in the FAQs (see Chapter 8, “FAQs - Frequently Asked

• HiPath 4000 SoftGate

Highlights and Hints

– New features added:

– RQ00030980: Licensing for HiPath Access modules directly

– 9 periperal slots for virtual boards or HiPath Access modules are

– Up to 18 different tones and 6 different announcements are available.

– RQ00033039: QDC support

– RQ00033880: MFC-R2 support (see Chapter 15, “MFC-R2”).

– More information regarding SLMA2 and TMOM2 (see Section 7.2,

– SIP Load Balancer enhancements for the support of OpenScape UC

• Payload Switching DMC

– Section 2.1.3, “Bandwidth Considerations”

– Section 2.3.6, “Troubleshooting Hints”

– Improvements in Chapter 3, “Generation (Example)” and Chapter 4,

• Access Point Emergency (APE)

• IP Distributed Architecture (IPDA)

– RQ00034930: NCUI SSH access enabled to be able to change NCUI

– Signaling Survivability is aslo released for HiPath Access (see Chapter 2,

– Signaling Survivability with WAML Replacement is only supported for

Highlights and Hints