MI TWS J18 Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

J18

wireless earphone

User Manual
Product specification
Product na me: J18
Bluetooth version: 5.0
Battery input: DC SV
Earphone battery: 30mAh
Charge case battery: 300mAh
Working time: About 3-4hours
Sensitive: 92±3dB
Frequency: 20-20000Hz
lmpedance: 320
Profile support: HSP/HFP/A2DP/AVRCP

Operation instructions

Binaural Function:

Touch once: Play/Pause Answer/End a call


Touch twice on L: Volume -
Touch twice on R: Volume +

Touch three times on L: Next song


o o

Touch three times on R: Previous song


Touch and hold 2 sec: Reject the calI
Touch and hold 2 sec then release: Wake up voice Assistant
L R
Product schematic

(!) ---+­
f--==---1 1+1-"'------ ®
·1+----®
@---+--0 o � cv
®-----=::::J---- -t
'-- :::::::_ ___ ____=---
__: _- ®

(!) Charge Case @ Charge •case indicator @ Charging Port


@) Dustproof Mesh ® Touch Area @ MIC
CV Earphone Charging Port ® Charge case button

Charging
Charging with charge case: The case's red LED flashes slowly.
Charging with earbuds: The case's green LE O flashes slowly.
When charging with the earphones: LED remains blue
Charging time: about 40 -60 minutes

Warning:
1. To ensure the battery life of the earphone, the earphones and the charge case should
be charged once in a month.
2. lf the earphones are placed in the charge case with being turned off, then press the
button on the charge case to start charging
3. When charging with charge case please use the SV/lA charger. Please don't use the
fast charger which over S V , to avoid damage on the charge case.
Pairing for operating
Stepl. Pick up the earphones from the charge case separately or long touch earphones
to turn them on, they will be automatically paired.
Step2. At this point, open the device's Bluetooth to search for "J18" and then
click to connect with device successful, voice prompted" Bluetooth connected ".

*When the earphones connect to the sarne device again, open the lid of charge case
it will turn on automatically then reconnect with the device, voice prompt" Bluetooth
connected ".

Turn on the earphone


Method A. Touch and hold the area for 2 seconds.
Method B. Take out earphones from the charge case, they will automatically power on,
and enter automatic pairing.

Turn off the earphone


Method A. Touch and hold the area for 5 seconds.
Method B. Put earphones into the charge case, they will automatically shut down and
enter charging.

*When the earphone disconnected for 3 minutes, it will automatically turn off.

Calling
When connected with mobile phone, the incoming call will be announced with an
English voice reminder, touch once any earphone to answer current call. long touch
for 2 seconds to reject the cal I. lf you want to end the current call, touch once any
earphone to stop.
FAQ
A. When the earphones can't be turned on
Check if the earphone has power (after the charge case is connected to the USB, and
the earphone is charged in the charge case for more than 1 hour ) .

B. When the earphones have only one side sound or earphones can't pair successfully
1. Make sure that both ear phones are powered and can be turned on normally.
2. When the earphones are in the off state, press the earphones for 7seconds to
restare the factory settings.
3. Touch 2 seconds to turn on the earphones or take the earphone out of thecharge
case(when the charge case is powered ) the earphone will power on voluntarily,
then you can connect with the device.

C. When the mobile phone cannot ftnd the device


1. Confirm that the two earphones are turned on.
2. Check if the earphone is connected to other devices.
3. Change a clear area and reconnect it again.

D. When the earphone is stuck or disconnect while talking or playing music


1. The earphone is low on battery.
2. The distance between the mobile phone and the earphone is more than 10 meters.
3. There is large area of signal obstruction between the mobile phone and the
earphone, such as a wall.
4. The left and right ears are not paired and synchronized, and need to be shut down
and re-paire d.

Attention
1. Please don't change the built-in batte r y by your self.
2. Please don't put the headset under wet o r rainy place.
3. Please don't expose the headset under the blaz ing sun , event not close
fire to avoid battery accident.
4. Please don't disassemble the headset if unpro fessional .

FCC Statement

Changes or modifications not expressly approved by the party responsible for


compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to com ply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not instal led and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. lf this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the followi n g measures:
-- Reorient or relocate the receiving antenna.
-- lncrease the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device compl ies with part 15 o f the FCC rules. Operation is subject to the
foll owing two conditions (1)this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Made in China

You might also like