SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments

Safety And Operation Instructions Revised 01/06

To Avoid Serious Injury And Ensure Best Results For Your Tapping Operation, Please
Read Carefully All Operator And Safety Instructions Provided For This Tapping
Attachment as well as all other safety intstructions that are applicable, especially those for your machine tool.
1. Proper Clothing: The rotating spindle of a machine tool can snag loose fitting clothing, jewelry or long hair. Never wear jewelry,
long sleeves, neckties, gloves or anything else that could become caught when operating a machine tool. Long hair must be restrained or netted to
prevent it from becoming entangled in rotating spindle.

2. Proper Eye Protection: Always wear safety glasses with

side shields to protect your eyes from flying particles.

3. Proper Work Piece Fixturing: Never hold the work piece or the vise it is held in, by hand.
The work piece must be clamped firmly to the table of the machine so that it cannot move, rotate or lift.

4. Proper Stop Arm / Torque Bar Installation

For Self-Reversing Attachments On
Conventional Machines:

Never extend the length of the standard stop arm supplied with
your tapping attachment. this will void warranty. A lengthened stop arm
could break free, hitting the operator and causing serious injury.

Never hold the stop arm by hand. On reversal, full power of the machine is transmitted through the stop arm
and the operator could be seriously injured.

Always mount a
torque bar to hold the
tapping attachment’s stop arm
from rotating. The torque bar
must be mounted securely to
the table or quill of your
machine. The torque bar
installation must be stronger Quill Clamp Order Max Torque Bar Order Max
Capacity No. Tap Size Assembly No. Tap Size
than the largest tap in the
capacity range of your tapping 1 1/2”-2 3/8” 29099 1/2” Table Mount 29097 3/4”
attachment. Order Tapmatic
Torque Bars shown. 2 3/8” - 4 1/2” 290991 3/4” Heavy Duty
Table Mount 29096 1 3/4”

1.) Torque Bar 2 .) Quill Clamp

Attached To Table Installation

5. To Install Collets In Rubber-Flex Collet Chucks: Rubber-Flex Collet

Some collets vary slightly in outside diameter. This does not affect For Use With Tapping Attachments With Rubber-Flex Collet Spindles.
capacity or performance. To install, put collet into the end of the drive Collet Range
spindle and push the tap chuck nut over it until the threads are engaged. Collet Series Catalog No. Tap Size Shank Size
Screw nut down completely. This will seat collet properly. Then back #21000 Series 21600 ★ #0-#8 Standard .098-.177
off nut to install tap. Collets must be ordered separately. For SPD3 attachments with 21700 ★ #10-1/4" Standard .177-.256
capacities (#0-1/4") 21500 .040-.098
6. Inserting Tap In Rubber-Flex Collet Chucks: 21200 .094-.146
Follow instructions to avoid excessive wear on back jaws when using #22000 Series 22100 ★ #0-1/4" Standard .139-.257
tapping heads with collet chucks. Insert the tap into the tap chuck of the For SPD5 attachments with 22200 ★ 1/4"-1/2" Standard .253-.383
attachment so that the back jaws will engage the square of the tap. Hand capacities (#6-1/2") 22300 .090-.180
tighten the chuck nut first, then tighten the back jaw on those units with 22000 .194-.318
#24000 Series 24100 ★ #10-1/2" Standard .176-.383
adjustable back jaws. Then using the wrenches provided tighten the For SPD7 attachments with 24000 ★ 5/16"-5/8" .280-.500
chuck nut firmly. When tightened correctly, the rubber flex collet should capacities (#10-5/8") 24300 .110-.280
absorb most torque pressure, preventing the back jaws from being #26000 Series 26100 1/2"-3/4" .360-.630
damaged by excessive torque. If the tap you are using has a male center For SPD9A attachments with 26200 7/8"-1-1/8" .630-.900
at the square end, you must remove the point to assure maximum capacities (1/2"-1-1/8")
engagement in the back jaws.

ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 1.
SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments
Safety And Operation Instructions
To Avoid Serious Injury And Ensure Best Results For Your Tapping Operation,
Please Read Carefully All operator and safety instructions provided for this tapping
attachment as well as all other safety intstructions that are applicable, especially those for your machine tool.

7. Always Be Aware Of The Potential Hazards Of A Machining Operation: Sometimes working with your machine can
seem routine. You may find that you are no longer concentrating on the operation. A feeling of false security can lead to serious
injury. Always be alert to the dangers of the machines with which you work. Always keep hands, body parts, clothing, jewelry and
hair out of the areas of operation, when the machine spindle is rotating. Areas of operation include the immediate point of machin-
ing and all transmission components including the tapping attachment. Never bring your hand, other body parts or anything
attached to your body into any of these areas until the machine spindle is completely stopped.

8. Be aware of any other applicable safety instructions / requirements.

9. The tapping attachment housing, drive spindle and tap itself can become hot to the touch after operation. Use
caution when removing the attachment from the machine or handling.

Check List For Good Tapping

❑ 1. Never use this unit before reading all safety instructions for this attachment as well as the machine it is to be used on.
❑ 2. Is tap sharp and of correct design for current job?
❑ 3. Is tap in proper alignment with drilled hole?
❑ 4. Is machine speed correct?
❑ 5. Is machine feed correct?
❑ 5. Is machine stop set properly so tap releases in neutral rather than bottoming in work piece or fixture?
❑ 6. Is work piece held rigidly against rotation and upward movement?
❑ 7. Is drilled hole the correct size?
❑ 8. Is clearance between the drilled hole and tap sufficient at start position to allow the tap to clear the hole upon
retraction?
❑ 9. Is the stop arm of the tapping attachment held rigidly against rotation by the torque bar extending from the machine
quill or table? Machine torque bar must be stronger than the largest tap to be used.
❑ 10. Is the proper cutting fluid or coolant being used for lubricating the tap?
❑ 11. If a bottom hole is being tapped is there sufficient chip clearance?
❑ 12. Is the correct Tapmatic model for the specific job requirement being used? (Capacity should be reduced 25% for roll
form taps.)
❑ 13. If a torque control attachment is being used, is the torque set correctly so tap will not break if accidentally bottomed?
❑ 14. If depth control feature is employed, is it set correctly to cooperate with the machine stop, provide the total thread
depth required and prevent engagement with bottom?
❑ 15. Is machine retraction correct for tapping attachment being used?
References for this Safety Information include American National Standards Instutitute Society Of Manufacturing Engineers
but are not limited to: ANSI B11.8-1983 (Adopted May 31, 1983 Tool and Manufacturing Engineers Handbook
by Department of Defense) Volume 1 Machining
(Library of Congress Catalog No. 82-060312
Coastal Video Communications Corporation
Machine Guarding Copy Right 1994
MAXIMUM TAPMATIC TAPPING SPEEDS**
Size Cast Iron and Plastics and Stainless Size Cast Iron and Plastics and Stainless
Bronze Aluminum Steel Steel Brass Copper Bronze Aluminum Steel Steel Brass Copper
0 -80 2000 2000 2000 1900 2000 2000 1/4 -20 1000 1200 750 400 1200 1200
1 -64 2000 2000 2000 1600 2000 2000 1/4 -28 1200 1200 850 400 1300 1200
1 -72 2000 2000 2000 1600 2000 2000 5/16 -18 850 1100 650 300 1200 1100
2 -56 1900 2000 1800 1300 2000 2000 5/16 -24 900 1200 700 350 1300 1200
2 -64 2000 2000 1900 1300 2000 2000 3/8 -16 700 900 550 250 1200 900
3 -48 1800 1900 1700 1000 1900 1900 3/8 -24 750 1000 600 300 1200 1000
3 -56 1900 2000 1800 1100 2000 2000 7/16 -14 600 800 450 200 950 800
4 -40 1700 1800 1500 900 1900 1800 7/16 -20 650 850 475 225 1000 850
4 -48 1800 1900 1600 1000 2000 1900 1/2 -13 500 650 400 200 850 650
5 -40 1650 1700 1600 800 1800 1700 1/2- -20 575 750 425 200 1000 750
5 -44 1750 1800 1700 900 1900 1800 9/16 -12 450 600 350 175 800 600
6 -32 1500 1600 1500 700 1700 1600 9/16 -18 500 675 375 175 900 675
6 -40 1650 1700 1600 800 1800 1700 5/8 -11 375 500 300 150 700 500
8 -32 1400 1400 1200 600 1400 1400 5/8 -18 450 600 325 150 800 600
8 -36 1500 1500 1300 700 1500 1500 3/4 -10 325 400 250 125 575 400
10 -24 1300 1400 1100 500 1500 1400 3/4 -16 375 475 275 125 650 450
10 -32 1400 1500 1200 600 1500 1400 7/8 -9 275 350 200 90 500 350
12 -24 1300 1400 900 400 1500 1400 7/8 -14 300 400 250 100 550 400
12 -28 1400 1500 1000 500 1500 1400 1 -8 250 300 175 75 425 300
1 -14 275 350 200 100 475 350

**These maximum tapping speeds are for optimum tapping conditions for the tap size, tap pitch and material involved. Optimum conditions are (1) a through hole or blind hole with generous chip clearance; (2) thread depth is one times
a tap diameter or less; (3) free machining material; (4) tap drill diameter for 60% thread; (5) use of LPS Tapmatic Cutting Fluid or Coolant; and (6) proper designed tap. Reduce speed accordingly for each non-optimum condition.
_______________________________________________________________________________________________________________________________________________________________________________________________

ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 2.
SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments
Safety And Operation Instructions
This tapping attachment can be used on all types of manually THROUGH HOLE TAPPING
operated or automated machines with rotating, non-reversing spindles. Through holes are easily tapped without machine stops or dwells;
It should not be used on machines which reverse on the back stroke. merely feed in and out, as desired. For programmed machine
operation, program the machine spindle to feed at, or slightly less than,
This attachment incorporates in its design a gear reverse which the taps' feed per revolution to insure production of quality threads.
has a 1to 1 reverse ratio. Reversing speed, then, is equal to the
machine's spindle speed. Therefore, the in-feed and out-feed of the Manual tapping with the attachment does not require operator to apply
machine spindle may remain the same. The "bore cycle" on most NC any lead pressure on the tap during the tapping operation. The free
machines can be employed for tapping. axial float in the attachment will automatically permit the tap to follow its
own lead. The operator merely moves the machine's spindle behind
MOUNTING THE STOP ARM the lead of the tap until the desired depth is reached. To reduce wear
There are three (3) screws provided with the unit to properly mount the within the tapper, it is recommended that a short, quick, upward
stop arm onto the top of the housing. movement of the machine spindle be made during transition from drive
to reverse. The tap will return to a forward rotation as soon as it is
Extend strong torque bar from machine quill or machine table to withdrawn from the hole.
engage short stop arm. DO NOT LENGTHEN STOP ARM. Also,
clamp part to be tapped securely as full power of the machine is BOTTOM HOLE TAPPING
transmitted in reverse. DO NOT HOLD PART BY HAND. DO NOT For accurate and efficient bottom hole tapping, a machine feed stop
HOLD STOP ARM BY HAND. should be used to allow the attachment's spindle to disengage in
neutral before the tap bottoms in the hole. To achieve this, set the
INSTALLING THE ARBOR IN TAPER MOUNT UNITS machine stop so that the machine feed plus the attachment's self-feed
Make sure that the taper mount of the unit and the arbor itself are will equal the desired thread depth. This greatly simplifies the tapping
clean and free of oil or grease. Then with a twisting motion, insert the operation, and affords maximum tap protection.
arbor into the tapping attachment. The twisting motion allows the air This attachment does not have a clutch. It is positive drive.
entrapped in the taper to be released. When the arbor is inserted These units have a fixed self-feed length. The amount of self feed is
completely, several sharp blows should be made on the tang with a 3mm for SPD3, 5mm for SPD5, 7mm for SPD7 and 10mm for SPD9A.
lead hammer to make sure the arbor is seated firmly. It is important For added tap protection in quick-change models, the torque release
that this procedure be followed, as the taper may be damaged if tap holders (TC style) may be employed. The tap will stop without
slippage occurs. Occasionally, for large units, it may be necessary for breaking if the bottom of the hole is accidentally engaged.
the attachment to be pinned to the arbor. This may be done with a #4
Taper Pin. LUBRICATION
Lubricate approximately every 100,000 holes.
INSERTING THE TAP
Rubber Flex Collet Spindle: BACK JAW To Lubricate: Remove set screw from housing wall, add grease (use
If the tap you are using has a 2 tubes), and reinstall set screw. FOR ADDITIONAL GREASE-USE
male center as in Figure 1, the MALE CENTER ORDER NO. 29000 FOR A CASE OF 12 TUBES.
point should be ground off so that
the tap square will be engaged MAINTENANCE NOTE: If tapping attachment becomes contami-
by the back jaws as shown in nated with coolant, submerge it in a light weight spindle oil. Allow the
Figure 2. oil to work through the unit, then remove and let stand. When most of
After removing the point, the oil has drained from the unit, re-grease it.
insert the tap into the tap chuck of CHUCK
the attachment so that the back NUT TAP LUBRICATION
jaws will engage the square of TAP To insure maximum tap life, the proper lubricant should be used. For
the tap. Hand tighten the chuck FIG. #1 an ALL PURPOSE tapping fluid that meets the toughest safety
nut first. Then tighten back jaws requirements use our MQL Systems DRY-CUT.
with hex key. Then using
wrenches provided, tighten chuck REMOVAL OF TAPERED ARBORS
nut. This procedure will assure Removal of the arbor from the Jacobs or DIN taper in a tapping
true running of the tap. FIG. #2 attachment will generally require striking the arbor with a soft metal rod.
Note: Reduce capacity 25% for Hold the tapping attachment, with the arbor pointed away, in one hand
roll form taps. and strike the arbor sideways on tang or in relief area, with a brass rod
grasped in the other hand. Numerous blows may be required. DO
Quick Change Spindle: To install or remove a tap adapter lift the NOT STRIKE THE TAPPING ATTACHMENT.
release collar #71A. Please order collets and tap adapters
separately. Stubborn arbors and arbors installed with Loctite will require the
application of heat. Using a soft flame propane torch, evenly heat the
TAPPING SPEEDS: The Tapping Attachment has been designed to interface area where the arbor enters the attachment. (300% F will be
operate properly at recommended tapping speeds. Please refer to required to break down the Loctite.) After applying heat, resume
chart for the recommendations for specific tap sizes. Do not exceed striking the arbor with the soft metal rod until the arbor loosens. Always
the maximum speed shown on the tapping attachment. use caution when handling heated parts.

PROGRAMMING INSTRUCTIONS WHEN USED ON CNC MACHINES

1. Utilize bore cycle of machine.
2. Set machine in-feed and out-feed at 98 to 100% of correct feed rate for thread pitch.
3. Establish clearance plane above hole (equal to diameter of largest tap within specific unit's capacity, up to maximum of 5/8" for largest tools)
where machine's rapid approach converts to feed rate so that tap will definitely clear hole during retraction before machine idexes to next
position.
4. For through holes or blind holes with sufficient clearance, simply machine feed to desired thread depth and retract.
5. For blind holes or controlled thread depth, machine feed to the desired thread depth minus the tapping attachment self-feed distance (see
"Bottom Hole Tapping" above). Check depth on first hole and adjust program depth accordingly.

ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 3.
Parts Listing
SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments

ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 4.
Parts Listing
SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments
IDENT PART NAME SPD3 SPD5 SPD7 SPD9 Notes:
_________________________________________________________________________________________________________________________________________________

2 Stop Arm Screws 51302 (3 required) 51502 (3required) 51502 (3required) 51902 (3required) (RF) Denotes Rubber Flex
*3 Cushion Spring 51312 51512 507122 509122 Only
*4 Spring Biased Driver 58304 58504 58704 509271
5 Ball Bearing 51305 50509 50708 50908 (Thd Mount) Denotes
5T Ball Bearings 51305 (2 required) 50509 (2 required) 50709 (2 required) 50909 (2 required) Thread Mount Only
5TI Shim 513052 51505 51705 51905
5X Lock Set Screw 56105A (1) 50305A (1) 50305A (1) 50905 (1) (1) Lock Set Screw comes
5XX Lock Set Screw Plug 561051 503051 503051 509051 with Ident #5XX.
6 Planet Gear 51306 (3 required) 51506 (3 required) 51706 (3required) 51906 (3 required)
6A Washer 513061 (3 required) 517061 (3 required) 517061 (3 required) 519061 (3 required) (2) Threaded (#19) or
7 Gear Axle & Washers 51307A (3 required) 51507A (3required) 51707A (3 required 51907A (3 required) Tapered (#19X)
8 Guide Spindle Bushing 50329 56529 50729 51908 Mount only supplied
9 Reversing Member 58309 (3) 585091 (3) 58709 (3) 58909 (3) as an assembly with
9A Flange Washer 513091 515091 517091 519091 part #5T, #5TI and
10 Lock Nut 58310 58510 58710 51910 #20
*11 Spring Biased Rev. Driver 58304 58504 58704 509271
*12 Reversing Drive Spring 51312 58512 507122 51912 (3) Reversing Member
14 Drive Spindle Bushing 58314C 585141C 58714C 58914C (#9) supplied as an
15 Retaining Ring 51315 58515 51715 50311 assembly with part #14
15X Set Screw 50315 50315 69364 50915 and #15.
*16X Back Jaws 503161 56516 50716 50916
17X Rubber Flex Collet (Small) 21600 22100 24100 26100 (4) Drive Spindle (#25)
17XX Rubber Flex Collet (Large) 21700 22200 24500 26200 only supplied as an
18 Tap Chuck Nut 50318 56518 50718 50918 assembly with part #8.
19 Threaded Mount (5/16-24) 51319HA (2) - - -
19 Threaded Mount (3/8-24) 51319IA 51519IA (2) - - (5) Quick Change Drive
19 Threaded Mount (1/2-20) 51319JA (2) 51519JA (2) 5819JA (2) - Spindle (#70QC) only
19 Threaded Mount (5/8-16) 51319KA (2) 51519KA (2) 58719KA (2) - supplied as an
19 Threaded Mount (3/4-16) 513191LA (2) 51519LA (2) 58719LA (2) 51919LA assembly with part #8,
19 Threaded Mount (7/8-20) - 51519MA (2) 587191MA (2) - #71, #72, #73, #74 and
19 Threaded Mount (1-1/2-18) - - - 51919NA (2) #75.
19X Taper Mount (#6JT) 51319BA (2) 51519BA (2) - - (6) Stop Arm (#21) only
19X Taper Mount (#33 JT) 51319EA (2) 51519EA (2) - - supplied as an
19X Taper Mount (DIN B12) 51319FA (2) - - - assembly with part #2.
19X Taper Mount (DIN B16) 51319GA (2) 51519GA (2) - -
19X Taper Mount (#3JT) - - 58719CA (2) - INSTRUCTIONS FOR
19X Taper Mount (#4JT) - - - 5191DA (2) DISASSEMBLY
20 Guide Spindle 58320 58520 51720 51920
*21 Stop Arm 51321A (6) 51521A (6) 51721A (6) 51921A (6) 1. Remove tap chuck
22 Ring Gear 51322 (2 required) 51522 (2 required) 51722 (2required) 51922 (2 required) (#18), rubber flex
23 Key 50319 51523 51723 51923 collet (#17X or XX),
24A Gear Carrier 51324 51524 51724 51924 back jaw retaining
24B Gear Carrier Spacer (Short) 513241 515241 517241 519241 screw (#34) and back
24C Gear Carrier Spacer (Long) 513242 515242 517242 519242 jaws (#16X)
25 Housing 58325 58525 58725 589259
26 Drive Pins 50328 (3required) 56528 (3 required) 50728 (3 required) 50928 (3 required) 2. (SPD7 and SPD9)
27 Gear Carrier Bushing 51327 51527 51727 51927 Remove return spring.
*28 Return Spring 51328 58528 507301 50930 (#28) by threading
*28QC Quick Change Return Spring 51228 58428 58928 58930 spring puller (supplied
31 Guide Spindle Washer 50333 - - -
*32 Guide Spindle Nut 503341 56534 - - with unit) into part
32A Spring Bearing - - 50734 50934 (#33) and pulling out
33 Spring Hanger - - 50706 50706 to expose spring for
34 Back Jaw Retainer Screw 50315 (2 required) 50315 50315 50915 hook also supplied
35 Drive Spindle 58335A (4) 58535A (4) 58735A (4) 589359A (4) with unit.)
*36 Safety Cushion Spring 58336 58536 58736 -
37A Upper Spring Hanger - - 60334 50706 3. Remove lock nut (#10)
70QC Quick Change Drive Spindle 58370A (5) 58570A (5) 58770A (5) 58970A (5)
71A Locking Ring 583711 585711 587711 628711 4. Remove all internal
72A Wave Spring 583721 (2 required) 585721 (2 required) 587721 (2 required) - components
72A Com. Springs - - - 58972 (4 required)
73A Washer 583731 585731 587731 62873 FOR ASSEMBLY
74 Truarc Ring 58374 58574 58774 62874 Reverse procedure outlined
75A Steel Balls 583751 (3 required) 60328 (3 required) 60528 (3 required) - above.
75A 7/32 Ball - - - 58976
75A 9mm Balls - - - 62875 (2 required)
77 QC Adapter Housing 29510 29511 29512 29513
78 QC Tap Jaws 29496 (8 required) 29497 (10 required) 29498 (12 required) 50916

WRENCH 5/64 HEX KEY RF 27078 27078 27078 27078

KITS 1/8 Hex Key 27125 27125 - 27125
3/32 Hex Key 27093 27093 27093 27093
5/32 Hex Key - 27156 27156 -
7/32 Hex Key - - - 27218
5/8 Wrench (RF) 28062 - - -
1/2 WRench (RF) 28050 - - -
3/4 Wrench (RF) - 28075 - -
31/32 Wrench 28097 28097 28097 -
1 5/16 Wrench - 28131 28131 -
1 9/16 Wrench (RF) - - - 28156
#5 Hook - - 29085 -
Spring Puller - - 29090 29090
2 Wrench - - - 28200
#1 Hook - - - 29081
*These items are considered normal wear parts.
ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 5.
Repair Policy
SPD3, 5, 7 and 9A Self-Reversing Tapping Attachments

Repair Service is available at... Attention: Repair Department

Tapmatic Corporation
802 Clearwater Loop
Post Falls, ID 83854

To Expedite Repair
Return tool direct to Tapmatic Corporation, by United Parcel Service and enclose the following statement with your
purchase order: "Authorization given to repair and return tool, without notification if total repair cost does
not exceed 40% of the cost of a new tool." Tapmatic will repair the tool and call to request your credit card # for
invoicing.

Important: Be sure to return the tool complete with the tap chuck nut, back jaw and if the tool is a reversing unit,
include stop arm. Otherwise, we will add these missing parts to every non-warranty repair.

Cost Notification: Tapmatic will FAX a cost notification to you, soliciting your approval before repairs are
completed.

If it is determined that a tapping attachment cannot be repaired, at the customer's request, Tapmatic will return the
disassembled parts. We are not able to reassemble tapping attachments using damaged or worn out parts.

Optional Return Procedure: Tools may also be returned for repair through your local Tapmatic Distributor.
They will ship the tool to us and include instructions for the repair and return. You may already have an open
account with them which facilitates the handling of invoicing.

Priority Service: Tapmatic services tapping attachments returned for repair in the order in which they are received.
All tools will be evaluated and repaired within three weeks from the date they arrive subject to receiving the
customer's approval to proceed with the repair.

Priority is given to the tools shipped to us by overnight or second day.

If a repair is sent to us by UPS ground or similar service it can also be given priority. Just call and let us know you
need priority service and advise if you would like the tool returned to you by overnight or second day. In the
interest of fairness, to all our customers, we ask that you approve return shipment by overnight or second day before
we agree to upgrade your repair order to priority service. Typical turnaround, not including shipping time, for
priority repairs is 3 days subject to receiving the customer's approval to proceed with the repair.

If we can answer any questions, please call our toll free number: 800 395-8231.

Distributed By:

The Tapping Specialists

TAPMATIC CORPORATION: ISO 9001 CERTIFIED
802 Clearwater Loop, Post Falls, Idaho 83854
Phone: (208) 773-8048, (800) 854-6019, FAX: (208) 773-3021

TAPMATIC INTERNATIONAL CORPORATION

Alte Rheinstrasse, CH-9451 Kriessern, Switzerland
Phone: 41 71 757 5900, FAX: 41 71 757 5901
Form#: 0307/SPD/NCG/1M
ISO 9001 CERTIFIED- 802 Clearwater Loop, Post Falls, ID 83854, Phone: 800 854-6019, 208 773-8048, FAX: 208 773-3021, www.tapmatic.com 6.