Pintura 7000 - System - Cold - Galvanizing - Compound - RO65 - GDH585 - 0622

SPECIALTY TECHNICAL DATA RO-65
RUST-OLEUM® 7000 SYSTEM

COLD GALVANIZING COMPOUND
DESCRIPTION AND USES PRODUCT APPLICATION (cont.)

A single package zinc rich coating. This coating contains EQUIPMENT RECOMMENDATIONS
95% metallic zinc in the dry film to provide cathodic
BRUSH: For touch up only. Use a good quality natural or
corrosion protection for iron and steel. Cold Galvanizing
polyester bristle brush.
Compound is also excellent for the repair of worn or
damaged galvanized steel. This product is not intended for ROLLER: Not recommended.
use on rusted steel or previously coated surfaces. It meets
the performance requirements of ASTM A-780-01 (par. AIR–ATOMIZED SPRAY
4.1.2, 4.1.3, 4.2.2) MIL-P-21035B and SSPC Paint 20. Atomized
Method Fluid Tip Fluid Delivery Pressure
PRODUCTS Pressure 0.055-0.070 16 oz./min. 25-60 psi
SKU DESCRIPTION AIRLESS SPRAY

206194T 1-Quart Fluid Pressure Fluid Tip Filter Mesh
206193 1-Gallon 2,100-2,400 psi 0.019-0.021 60
PRODUCT APPLICATION THINNING

READ ALL INSTRUCTIONS CAREFULLY BEFORE BRUSH/ROLLER: Normally not required
STARTING PROJECT
AIR ATOMIZED SPRAY: 633402 Thinner: Normally not
SURFACE PREPARATION required. If needed, use up to 5% by volume.
AIRLESS SPRAY: 633402 Thinner: Normally not required.
ALL SURFACES: Remove all dirt, grease, oil, salt and
If needed, use up to 5% by volume.
chemical contaminants by washing the surface with
Krud Kutter® Original Cleaner Degreaser, commercial
CLEAN-UP
detergent or other suitable cleaner. Rinse thoroughly with
fresh water and allow to fully dry. All surfaces must be dry at 633402 Thinner or mineral spirits.
time of application.
PERFORMANCE CHARACTERISTICS
STEEL: At minimum, clean in accordance to SSPC-SP-11
Power Tool Clean to Bare Metal. The 7000 System is CYCLIC PROHESION
intended to be applied only to bare steel or existing sound Rating 1-10, 10=best
galvanized steel. It is not intended for application to sound METHOD: ASTM D5894, 5 Cycles, 1680 hours
rust. RESULT: 10 ASTM D714 for blistering
RESULT: 10 ASTM D1654 for corrosion
APPLICATION RESULT: 9 ASTM D610 for rusting
IMPORTANT: Product must be properly mixed before and
during use. Hand mixing will not adequately mix product and CONICAL FLEXIBILITY
produce inconsistent results and is not an approved method. METHOD: ASTM D-522
Power mixing is required to properly mix material into a RESULT: Pass >33%
useable state.
Apply only when the air and surface temperatures are
between 32-100°F (0-38°C) and the surface temperature is
at least 5°F (3°C) above the dew point. Abrasive blast clean
steel requires two coats of coating.
1 Form: GDH-585
Rev.:061522
SPECIALTY TECHNICAL DATA RO-65
RUST-OLEUM® 7000 SYSTEM

COLD GALVNIZING COMPOUND
PHYSICAL PROPERTIES
COLD GALVANIZING COMPOUND

Resin Type Epoxy ester
Pigment Type Metallic Zinc
Solvents Aliphatic Hydrocarbons
Per Gallon 28.3 lbs.
Weight
Per Liter 3.4 kg
By Weight 89.5%
Solids
By Volume 54.1%
Volatile Organic Compounds <360 g/l (3.0 lbs./gal.)
Recommended Dry Film 2.5-3.5 mils
Thickness (DFT) Per Coat (62.5-87.5µ)
Wet Film to Achieve DFT 3.5-4.5 mils
(unthinned material) (87.5-112.5µ)
Practical Coverage at Recommended DFT
310-440 sq. ft./gal. (7.6-10.8 m2/l); based on wet to dry ratio
(assumes 15% material loss)
Tack-free 30-60 minutes
Dry Times at 70-80°F
(21-27°C) and 50% Handle 1-2 hours
Relative Humidity Recoat 12 hours
Dry Heat Resistance 212°F (100°C)
Shelf Life 2 years
COMBUSTIBLE LIQUID AND VAPOR. HARMFUL IF INHALED. MAY
AFFECT BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS,
HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT, EYE AND
Safety Information
SKIN IRRITATION. FOR INDUSTRIAL OR COMMERCIAL USE ONLY.
KEEP OUT OF REACH OF CHILDREN. SEE THE PRODUCT MATERIAL
SAFETY DATA SHEET (MSDS) AND LABEL WARNINGS FOR
ADDITIONAL SAFETY INFORMATION.
Calculated values are shown and may vary from the actual manufactured material.
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway Phone: 877∙385∙8155 Form: GDH-585
Vernon Hills, Illinois 60061 www.rustoleum.com/industrial Rev.: 061522

Pintura 7000 - System - Cold - Galvanizing - Compound - RO65 - GDH585 - 0622

Uploaded by

Copyright:

Available Formats

Pintura 7000 - System - Cold - Galvanizing - Compound - RO65 - GDH585 - 0622

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pintura 7000 - System - Cold - Galvanizing - Compound - RO65 - GDH585 - 0622

Uploaded by

Copyright:

Available Formats

SPECIALTY TECHNICAL DATA RO-65

RUST-OLEUM® 7000 SYSTEM

DESCRIPTION AND USES PRODUCT APPLICATION (cont.)

SKU DESCRIPTION AIRLESS SPRAY

PRODUCT APPLICATION THINNING

RUST-OLEUM® 7000 SYSTEM

COLD GALVANIZING COMPOUND

You might also like