Scribd
Upload
16 views2 pages

ESC201 Assignment 7

Determine RB and RC such that the transistor is in saturation with IC=2mA and forced=20 when Vi=5V. Draw the voltage transfer characteristics (a plot of V0 vs Vi) with these resistances.

Uploaded by

garud2221
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views2 pages

ESC201 Assignment 7

Determine RB and RC such that the transistor is in saturation with IC=2mA and forced=20 when Vi=5V. Draw the voltage transfer characteristics (a plot of V0 vs Vi) with these resistances.

Uploaded by

garud2221
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

4.

Determine RB and RC such that the transistor is


7 in saturation with IC=2mA and forced=20 when
Vi=5V. Draw the voltage transfer
characteristics (a plot of V0 vs Vi) with these
resistances.
5V

Topics IC
RC
BJTs, OPAMPs
RB V0
Questions Vi =100

1. Determine 𝑉𝐶𝐶 and R B in the following circuit.


5. For the circuit shown below, carry out ac
VCC 𝑣
analysis to determine the ratio 𝑖 0 , where vo is
𝑠
R 2.2k ac output voltage and 𝑖𝑠 is ac sinusoidal
B current. Assume that transistor is biased in
forward active mode and current gain 𝛽= 100.
+
7.2V
10A -
4mA

2. Determine IC and VCE in the following circuit.

20V
510k 2.4k
  6. For the following circuit, calculate VCEQ and
IC
ICQ. Also, calculate the small signal voltage
+ 𝑣
VCE gain 𝐴𝑣 = 𝑣𝑜 and the input impedance (𝑍𝑖 =
= 𝑖
- 𝑣𝑖
1.5k 𝑖𝑖
).

3. Determine IC and VCE in the following circuit.


16V

3.6k

470k IC
 +
VCE =
-

510
7. Determine the output of the ideal op-amp 9. Design an op-amp circuit that can produce
2
circuits shown below. 𝑉𝑂 = 𝐾 × 𝑉𝐼𝑁 where Vin is the input voltage.

10. Sketch the output voltage of the circuit shown


below for 𝑉𝑖𝑛 = 1𝑉𝑠𝑖𝑛(2𝜋𝑓𝑡); 𝑓 = 1𝐾𝐻𝑧 and
supply voltages of ±5𝑉

i.

11. Determine the output for the ideal op-amp


circuit shown below.

ii.

12. Determine the output for the ideal op-amp


circuit shown below. For the transistor assume
a current gain of 100. What is the usefulness of
each of the circuits?
iii.

iv.

8. Design an op-amp circuit that would generate


the following output voltage 𝑉𝑂 = 2𝑣𝑠1 +
4𝑣𝑠2 − 8𝑣𝑠3 − 10𝑣𝑠4 where vs1, vs2, vs3 and vs4
are input voltages.

You might also like