HomeLink Programming

Training with Intellicode® Transmitters
Use this process to train the HomeLink device for the following remotes shown below:
*If the remote you are using is not shown or this process does not work, see the next section for additional options.
Train HomeLink device to the Remote:

NOTES: 1) Choose an unused button on the HomeLink device that will be used to open the door. 2) Hold the transmitter
2 inches away from the HomeLink device. 3) To clear the HomeLink device completely, see the end of the instruction.
1. Press and hold down any button on the remote AND press and hold
down the chosen button on the HomeLink device AT THE SAME TIME.
The HomeLink indicator LED blinks slow at first and then change to a
faster blink rate ‐ once the blink rate changes to fast (could take up to 20
seconds) – then release both buttons. Before you proceed, make sure This remote HomeLink
shown as Device
the HomeLink device indicator has stopped blinking completely. example only (button)
2. When the HomeLink device indicator STOPs blinking, press and hold down the chosen button on the HomeLink
device for a full 5 seconds ‐ then release. (Ignore the HomeLink transmitter indicator during those 5 seconds.)
3. Confirm that the HomeLink device picked up the transmission from the remote by pressing the chosen button
on the HomeLink device. The operator head LEDs should light in response. If the operator LEDs light, continue
to the next steps. If after holding down the HomeLink device button for 5 seconds or longer, the LEDs on the
head do not light, repeat from step 1 in this section until the operator LED lights blink in response to the
HomeLink device button press.
Program the HomeLink Device to the Opener:

NOTES: 1) For additional instructions, see the motor vehicle manual, visit www.homelink.com, or visit
www.geniecompany.com.
1. Locate either a square PROGRAM button (PRGM) or round LEARN CODE button on the opener (ceiling). The
location could be anywhere on the cover of the opener or under a lens depending on the model.
2. Put opener into programming mode ‐ the openers programming window will time out after 30 seconds:
‐ PRGM button ‐ press and hold down until the LED turns blue, then release. Purple LED begins flashing.
‐ LEARN CODE button – press and hold down until the red LED starts flashing, then release.
3. Press and hold down the HomeLink button for 2 full seconds ‐ then release. Press and hold down the chosen
HomeLink button again for 2 full seconds – then release. Continue this process until the opener operates. During
this time, LEDs on the HomeLink device continue to blink and eventually change to solid (opener should be
moving by then).
If you have these remotes, please follow the instructions below:
Software version
Either of these remotes with

a software revision of lower
than (but not equal to) 2.03.
Software revisions can be
found on the back of these LED locations
remotes under the visor clip.
Preparing the Remote:
1. Choose a button on the remote that you will use to train the HomeLink device.
 If the LED on the transmitter lights RED, proceed to step 2.
 If the LED on the transmitter lights GREEN – perform the following steps:
1. Press and hold down this button for approximately 10 seconds or until BOTH A RED
AND A GREEN LED light on the remote – then release the button.
2. Immediately press the same button again quickly two times.
3. Press the same button again – the ONLY LED that should light is a RED one. If a GREEN
LED lights, repeat this process again until the only LED that lights at the end of step 1 is
red.
2. Continue with step 1 under “Train HomeLink device to the Remote” section above.
If you need to clear out your HomeLink device:

NOTE: 1) If at any time you need to start over completely, this process will remove all previously
programmed garage door openers from the HomeLink device.
1. Press and hold down the first and third buttons on the HomeLink device until the
indicator blinks slow at first and then fast for 20 seconds – then release both buttons.
The Genie Company • One Door Drive • Mt. Hope, OH 44660

Customer Care: 800-354-3643 • www.geniecompany.com Rev June 2022

HomeLink Programming

Uploaded by

Copyright:

Available Formats

HomeLink Programming

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HomeLink Programming

Uploaded by

Copyright:

Available Formats

Training with Intellicode® Transmitters

Train HomeLink device to the Remote:

Program the HomeLink Device to the Opener:

Either of these remotes with

Preparing the Remote:

If you need to clear out your HomeLink device:

The Genie Company • One Door Drive • Mt. Hope, OH 44660

You might also like