Uretek Resin 2409

General Properties and Applications Uretek Resin 2409 is a polyol formulation that together with Uretek
Hardener-10 will generate an expandable resin with a free rise density of
3
approximately 36 kg/m .
This system is suitable for deep injection.
Typical data
Property Unit Value Method
Density at 20ºC kg/m³ 1046 PET-07-01
Viscosity at 25ºC mPa.s 475 PET-10-01
Chlorine content ppm none
Appearance black

Packaging Drum, IBC, bulk

Storage Storage temperature 15 - 25ºC
Storage stability 6 months

Store the material in its original packaging to prevent moisture ingress in a dry
well ventilated area not exposed to direct sunlight and in compliance with local
safety requirements.

Labeling and REACH applications This product data sheet is only valid in conjunction with the latest edition of the
corresponding Safety Data Sheet. Any updating of safety-relevant information
– in accordance with statutory requirements – will only be reflected in the Safety
Data Sheet, copies of which will be revised and distributed. Information relating
to the current classification and labeling, applications and processing methods
and further data relevant to safety can be found in the currently valid Safety
Data Sheet.
Directions for Processing
Recommended mixing ratio volume: weight:
Uretek Resin 2409 100 100
Uretek Hardener-10 135 158

Manual foam test (internal lab. meth.; PET-55-02 5ºC):

Start time: 10 s
Gel time: 26 s
Tack free time: 35 s
Free rise density: 36 kg/m³

Further information about mechanical properties and resin properties

such as chemical resistance and environmental impact are available upon
request.

These values are given only as a guide and must be verified in each individual case on finished
parts manufactured under the processor’s production conditions.

page 1 of 3
Edition 2019-11-01 Uretek Resin
Replaces edition dated 2012-11-12 Product Datasheet
Uretek Resin 2409

Mechanical properties The mechanical strenght of Uretek Resin 2409 is evaluated by performing
compressive strenght measurements according EN 826. According this
standard the compressive strenght is measured at 10 % defoarmtionof the
material.

page 2 of 3
Edition 2019-11-01 Uretek Resin
Replaces edition dated 2012-11-12 Product Datasheet
Uretek Resin 2409

Processing Uretek Resin 2409 should only be used in combination with Uretek
Hardener-10, using appropriate equipment and correct mixing ratio.
The component temperature should be between 35 and 55°C.
Safety precautions Scorching
To avoid scorching of the resin during injection the filling of large cavities (larger
then 30 litres) should be avoided. In practise this means that injection should
be stopped if no lifting is recorded after 2 minutes of continuous injection.

Further data relevant to safety can be found in the currently valid Safety Data
Sheet.

The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal,
written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is
imperative that you test our products, technical assistance, information and recommendations to determine to your own satisfaction whether our
products, technical assistance and information are suitable for your intended uses and applications. This application-specific analysis must at least
include testing to determine suitability from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been
done by PLIXXENT. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which
are available upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice.
It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in
connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized
and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to
any material or its use. No license is implied or in fact granted under the claims of any patent.
This product is not designated as „Medical Grade” (1) and therefore shall not be considered a candidate for the manufacture of a medical device or of
intermediate products for medical devices, which are intended under normal use to be brought into direct contact with the patient's body (e.g., skin, body
fluids or tissues, including indirect contact to blood)*. [This product is also not designated for Food Contact (2), including drinking water, or cosmetic
applications. If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices, for Food
Contact products or cosmetic applications PLIXXENT must be contacted in advance to provide its agreement to sell such product for such purpose.]
Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food
Contact products or cosmetic applications must be made solely by the purchaser of the product without relying upon any representations by PLIXXENT.
1) Please see the "Guidance on Use of PLIXXENT Products in a Medical Application" document.
2) As defined in Commission Regulation (EU) 1935/2004.
Editor: Plixxent A/S
Kronborgvej 24
5450 Otterup
Denmark
Contact :
www.plixxent.com E-Mail: [email protected]
page 3 of 3
Edition 2019-11-01 Uretek Resin
Replaces edition dated 2012-11-12 Product Datasheet