NIKO-SEM High Performance Single Synchronous GS9238

GStek series Buck Converter

Features General Description

 Wide Output Current Range：8A The GS9238 is small size chip with a relative
 Wide Input Voltage Range：3V~28V constant on-time synchronous buck switching
 Adjustable 0.8V~20V Output Range converter suitable for applications in notebook
 ±1% Output Voltage Accuracy over Line and computers and other battery operated portable
Load devices. Features include wide input voltage
 Constant-on-time control scheme for fast range, high efficiency and fast dynamic response
transient and high Efficiency The GS9238 has a unique power save mode,
 Programmable Operation Frequency from which can save battery power supply by
100kHz to 600kHz decreasing frequency when load current falls
 Integrated 20 mΩ at LDO=5V N-Channel down below preset critical current point.
MOSFET For High Side The fast dynamic transient response means that
 Integrated 9.5 mΩ at LDO=5V N-Channel buck converter applications based on GS9238
MOSFET For Low Side will provide about 100ns-order response to load
 Selectable Forced PWM or automatic when output voltage falls down or rises up. The
PFM/PWM mode frequency will increase or decrease to meet the
 Power Good Indicator change in output load. Moreover, the GS9238 will
 Under-Voltage Protection take the same method to regulate the output
 Over-Voltage Protection voltage when input voltage changes. When
 FB Short Protection transient response regulated, the converter will
 Internal 5V Pre-regulator maintain a new steady-state operation. Both the
 External Adjustable Soft-Start and Soft-Stop transient response state and the new state, the
 Over Temperature Protection GS9238 always has the same on-time width.
 Over Current Protection The GS9238 is suitable for the solutions which
 TQFN23-4x4 package the output voltage is between 0.8V and 20V. An
 Green Product (RoHS, Lead-Free, external setting resistor and output voltage can
Halogen-Free Compliant) set the on-time width and frequency for the
converter. Additional features include current limit,
Applications soft-start, over-voltage and under-voltage
 Notebook computers protection, a Power Good flag and soft discharge
 CPU core/IO Supplies upon shutdown. The GS9238 is available in
 Chip/RAM Supplies package TQFN23-4x4.

This document is NIKO-SEM's confidential information. Anyone having confidential obligation to NIKO-SEM shall keep this document confidential. Any
unauthorized disclosure or use beyond authorized purpose will be considered as violation of confidentiality and criminal and civil liability will be asserted.

Rev.:1P8 1 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Typical Application
4.5V~5.5V VIN
AIN VIN
RTON CVIN

RPOK VCC
CLDO TON

BOOT
CBOOT
GS9238 L1 VOUT
PGOOD LX
ON
RFB1
EN
OFF
Coption
PFM FB
RFB2
CVOUT

SS AGND
CSS

PGND

Figure 1a Typical Application of GS9238

VIN
AIN VIN
RTON CVIN

VCC
CLDO TON
RPOK
BOOT
CBOOT
GS9238 L1 VOUT
PGOOD LX
ON
RFB1 Coption
EN
OFF
PFM FB
RFB2 CVOUT

SS AGND
CSS

PGND

Figure 1b Typical Application of GS9238

Rev.:1P8 2 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Function Block Diagram

PGOOD AIN VCC SS BOOT VIN

1 7 21 23 20 8, 9, 22

Pre Reg

Vref=0.8V
Soft Start High Side
Bandgap
MOS
EN 2 Enable DRV
VCC UVLO LDO UVLO
LX
10,11,
TON 16~18
TON 6 Generator
Gate Control
Low Side
Logic
MOS

OVP DRV
1V Protection
Error
AMP

Logic
0.36V
UVP
OCP
Error
AMP

0.8V
Error AMP

PWM
CMP
GM

12~15,
5 4 3 19

FB AGND PFM PGND

Figure 2 Function Block Diagram

Rev.:1P8 3 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Pin Configuration
SS VIN VCC BOOT PGND LX
23 22 21 20 19 18

PGOOD 1 17 LX

EN 2 16 LX
24 25

PFM 3 15 PGND
VIN LX
AGND 4 14 PGND

FB 5 13 PGND

TON 6 12 PGND

7 8 9 10 11
AIN VIN VIN LX LX

( Top view )
Figure 3 TQFN23-4x4 Package

Pin Descriptions
No. Name I/O Description
Power Good Signal Output. PGOOD is an open-drain
1 PGOOD O
output used to indicate the status of the output voltage.
Buck Enable Control Pin. EN=Low, Shutdown; EN=High,
2 EN I
Power On.
PFM Selection Input. Connect PFM pin to VCC/VIN for
3 PFM I forced PWM operation. Connect PFM to ground for PFM
operation.
4 AGND O Analog Ground
Feedback Input. Adjust the output voltage with a resistive
5 FB I
voltage-divider between the regulator’s output and AGND.
On-Time Setting Input. Connect a resistor between VIN
6 TON I
and TON to set the on time width.
7 AIN I Supply Input for internal analog circuitry.

Rev.:1P8 4 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Supply Input. VIN is the regulator input. All VIN pins must
8, 9, 22, 24 VIN I
be connected together.
Upper Driver Floating Ground for Buck Controller. Connect
10, 11, 16, 17,18, 25 LX I/O
to an external inductor.
12,13, 14, 15, 19 PGND O Power Ground.
Bootstrap Capacitor Connection. Connect a capacitor
20 BOOT I
between BOOT and LX Pin.
21 VCC O Internal Linear Regulator Output.
Soft-Start Time Setting Pin. Connect a capacitor between
23 SS I/O
SS and AGND to set the soft-start time.

Ordering Information
GS9238TQ-R
1. Package 2. Shipping

No Item Contents

1 Package TQ: TQFN23-4x4

2 Shipping R: Tape & Reel

Example: GS9238 TQFN23-4x4 Tape & Reel ordering information is “GS9238TQ-R”

Rev.:1P8 5 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Absolute Maximum Rating (Note 1)

Parameter Symbol Limits Units

VIN, AIN to GND VIN, VAIN -0.3 ~ 30 V

TON to GND VTON -0.3 ~ 30 V
VCC, VPG to GND VCC, VPG -0.3 ~ 6 V
EN/PFM to GND VEN, VPFM -0.3 ~ 30 V
FB to GND VFB -0.3 ~ 6 V
BOOT Voltage VBOOT-GND -0.3 ~ 40 V
BOOT to LX Voltage VBOOT-LX -0.3 ~ 6 V
LX to GND DC -0.7 ~ 30
VLX V
<200ns -8 ~ 32
Package Power Dissipation at TA≦25°C PD_TQFN23-4x4 3546 mW
Junction Temperature TJ - 45 ~ 150 °C
Storage Temperature TSTG - 55 ~ 150 °C
Lead Temperature (Soldering) 10S TLEAD 260 °C
ESD (Human Body Mode) (Note 2) VESD_HBM 2K V
ESD (Machine Mode) (Note 2) VESD_MM 200 V

Thermal Information (Note 3)

Parameter Symbol Limits Units

Thermal Resistance Junction to Ambient θJA_TQFN23-4x4 28.2 °C/W

Recommend Operating Condition (Note 4)

Parameter Symbol Limits Units

VIN to GND (Note 5) VIN 3~28 V

AIN to GND (Note 5) VAIN 6~28 V
VCC to GND VVCC 4.5~5.5 V
EN, PFM to GND VEN, VPFM VEN= VPFM= VAIN V
Junction Temperature TJ -40 ~125 °C
Ambient Temperature TA -40 ~ 85 °C

Rev.:1P8 6 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Electrical Characteristics
(RTON=100KOhm, VIN=VAIN=VEN=12V, TA =25°C, unless otherwise specified)

Parameter Symbol Conditions Min Typ Max Units

Supply Voltage (VAIN)
Under voltage lock
VAIN_UVLO 5.5 V
out (Rising)

UVLO Hysteresis VAIN_UVLOHYS 0.2 V

5V Pre-regulator (VVCC)
Output Voltage VVCC 5.15 V
Under voltage lock
VVCC_UVLO 4.15 V
out (Rising)
VVCC_UVLOHY
UVLO Hysteresis 0.3 V
S

Reference Voltage
FB Reference
VFB VVCC=5V 0.8 V
Voltage
Control Input
EN Logic Low
VEN_L EN Falling 0.6 V
Voltage
EN Logic High
VEN_H EN Rising 1.6 V
Voltage
PFM Logic Low
VPFM_L PFM Falling 0.6 V
Voltage
PFM Logic High
VPWM_H PFM Rising 2.5 V
Voltage
PGOOD Signal
PGOOD Low
VPG IPG=1mA 0.5 V
Voltage
PGOOD Leakage
IPG_LEAK VPG=5V 1 uA
Current
VFB>125%, VPG go to
VPG_H 125 %
Low
PGOOD Threshold
VFB>90%, VPG go to
VPG_L 90 %
High
PGOOD Fault Delay TPG PG debounce time 20 us

Rev.:1P8 7 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Current Parameters
Quiescent Current IQ VFB =0.85V, VIN=12V 870 uA
Soft start current ISS VSS=0 10 uA
VEN =0, I(AIN) 4 uA

Shutdown Current ISHTDN VEN =0, I(TON) 0.01 uA

VEN =0, I(EN) -2 -1 uA

Logic Input Current IEN VAIN= VEN=12V 13 uA

FB Input Bias
IFB FB=0.8V -0.1 0.001 0.1
Current uA
System Time & Driver On-Resistance
VIN=12V,VFB=0.79V,
On-Time TON 300 ns
RTON=100K,VOUT=1.2V
VIN=12V, VFB=0.79V,
Minimum Off-Time TOFFMIN 440 ns
RTON=100K
High Side MOS
RDSH BOOT-LX=5V 20 mohms
RDSON
High Side Leakage ILEAKH 10 uA
Low Side MOS
RDSL VCC-GND=5V 9.5 mohms
RDSON
Low Side Leakage ILEAKL 10 uA
Current Sensing
Current
ILIM GND-LX 8 A
Limit(Rising)
Zero Crossing
VT_0 GND-LX -10 10 mV
Threshold
Voltage Fault Protection
Measure at VFB, with
UVP Threshold VUV_TH respect to reference 45 %
voltage
From Enable to UVP
1.6x108xCS
UVP Blank Time TUV_B 80mV<VFB<UVP ms
S
Threshold
Force VFB below UVP
UVP Fault Delay TUV_D 20 us
threshold

Rev.:1P8 8 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Measure at VFB, with

OVP Threshold VOV_TH respect to reference 125 %
voltage
Force VFB above OVP
OVP Delay TOV_D 20 us
Threshold
Over Temperature Shutdown
Thermal Shutdown
TTSDN 150 °C
Threshold
Thermal Shutdown
THYS_TSDN 20 °C
Hysteresis
Bootstrap Diode
Internal Boost
Charging Switch RBT_D VCC to BOOT, 10mA 120 ohms
On-Resistance
Note 1.Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the
device. These are for stress ratings. Functional operation of the device at these or any other
conditions beyond those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods may remain possibility to affect
device reliability.
Note 2.Devices are ESD sensitive. Handling precaution recommended.
Note 3.θJA is measured in the natural convection at TA=25°C on a high effective thermal conductivity test
board (4 Layers, 2S2P) of JEDEC 51-7 thermal measurement standard.
Note 4.The device is not guaranteed to function outside its operating conditions.
Note 5 Recommend the Pulse time<100ns when VIN over than 30V.
Note 6 If V(BOOT)-V(LX)<4V, a boot diode is recommended.

Rev.:1P8 9 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Typical Characteristics
On-time vs. Input Voltage Frequency vs. Input Voltage
VIN=12V，RTON=100K，Vout=1.2V VIN=12V，RTON=100K，Vout=1.2V

Frequency vs. Load Current VOUT Efficiency vs. Load Current

VIN=12V，Vout=1.2V VIN=12V，Vout=1.2V

Frequency vs. Load Current OUT Efficiency vs. Load Current

VIN=5V，Vout=1.2V VIN=5V，Vout=1.2V

Rev.:1P8 10 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Frequency vs. Load Current Frequency vs. Load Current

VIN=24V，Vout=1.2V VIN=24V，Vout=1.2V

Power Off From EN Power on from EN (DEM Mode, No Load)

CH1:VOUT CH2:LX 3:EN CH4:PGOOD CH1:VOUT CH2:LX 3:EN CH4:PGOOD

Power on from EN (CCM Mode, No Load) Power on from EN (8A Load)

CH1:VOUT CH2:LX 3:EN CH4:PGOOD CH1:VOUT CH2:IOUT CH3:LX CH4:PGOOD

Rev.:1P8 11 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Power on from EN (125m Load) OVP

CH1:VOUT CH2:IOUT CH3:LX CH4:PGOOD CH1:VOUT CH3:LX CH4:PGOOD

UVP Power ON in Short Condition

CH1:VOUT CH2:IOUT CH3:LX CH4 PGOOD CH1:VOUT CH2:IOUT CH3:LX CH4:PGOOD

Load Transient CCM Mode Load Transient DEM Mode

CH1:VOUT CH2:IOUT CH3:LX CH1:VOUT CH2:IOUT CH3:LX

Rev.:1P8 12 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Application Information
The GS9238 is small size chip with a relative High Side Switch On-Time Count
constant on-time synchronous buck switching The on-time is decided by the external setting resistor,
converter suitable for applications in notebook and the input voltage. Looking at the TON pin, the input
computers and other battery operated portable voltage is converted to current which is inversely
devices. Features include wide input voltage proportional to itself by dividing the external setting
range, high efficiency and fast dynamic response. resistor. The input voltage-proportional current is used
System Clock Generator and PWM Control to charge an internal capacitor from zero volts. When
The on-time of GS9238 can be set by an external the voltage between two terminals of the capacitor
setting resistor from input voltage to TON Pin. The reaches to the internal setting voltage, on-time one-shot
converter maintains the on-time width as loop pulse is generated, and then upper power MOSFET is
feedback path exists between the GS9238 converter, turned off and lower power MOSFET is turned on.
low pass filter and voltage divider. For a given input We can count the on-time and switching frequency
voltage buck application, the feedback maintains the according to the equations below:
constant on-time width. Due to the constant resistor TON=(14.4p×RTON+1.44u) / (VIN-0.8)
and input voltage, the GS9238 based buck converter Then, the switching frequency is:
has the relative constant frequency. Moreover, the Fsw=VOUT/ (VIN×TON)
GS9238 can increase the duty-cycle automatically as RTON is a resistor connected from the input supply (VIN)
input voltage falls down. Because of the constant to the TON pin.
on-time in each switching period, the converter For heavy load (more than 8A) application, due to
maintains the relative frequency when the input ground bounced and the high impedance of RTON, the
voltage changes TON pin should always be bypassed to GND using a
At the beginning of each switching cycle, upper several nF-order ceramic capacitor for reliable system
power MOSFET is turned on, after typical fixed operation.
on-time, the upper MOSFET is turned off, and then EN, PFM/PWM Mode and Shutdown Soft-Discharge
lower power MOSFET is turned on after internal The EN pin enables the power supply. When EN is tied
dead time. The upper MOSFET will not be turned on to VIN and the PFM Pin is pulled low, the GS9238
at the beginning of next cycle until output voltage falls converter is enabled and diode-emulated mode (DEM,
down below the preset voltage and the dead time which is power save mode) will be also enabled. When
passes. The same events repeat the following the PFM pin is pulled high, it will force the converter into
switching cycles. To avoid the surge inductor current PWM mode.
during large load transient, a minimum Off-time is In PFM(DEM) mode, when the loads goes low, GS9238
added. Typical minimum off-time is around 440ns. starts power save mode in order to maintain the on-time
The too small on-time can affect soft-start and and decrease the system clock frequency to skip PWM
anti-noise ability, so in order to avoid the on-time too pulses for better efficiency. If DEM Mode is enabled, the
small to be eliminated; a minimum on-time is set to GS9238 zero crossing comparator will sense the
around 110ns. This should to be noted in the small inductor current and judge its value by comparing the
duty applications. LX node (LX) to PGND. Once the LX node voltage is

Rev.:1P8 13 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

equal to the PGND node voltage, the converter will and RFB2 can be set by the equation below:
enter the DEM Mode and turn off the low side power Set RFB2，then
MOSFET. The boundary of PWM to PFM mode can
 VOUT 
be calculated by the output current. RFB1  RFB 2    1 
 0.8  VDROP 
VIN VOUT 1 VOUT
IOUT(Boundary)   
2L FSW VIN Current Limit
As the load current is further decreased, it takes The GS9238 uses the on-state resistance of the
longer time to discharge the output capacitor to the low-side power MOSFET as a current-sense resistor. In
level than required the next switching cycle. The this case, the GS9238 build in a current limit threshold
on-time is kept the same as that in the heavy-load at least 8A. The current sensing circuit actually
condition. regulates the inductor valley current. This means that if
If the EN pin is pulled low, the GS9238 internal logic the magnitude of the inductor valley current beyond the
will shutdown the switching clock and stop the buck current limit, the PWM is not allowed to initiate a new
converter, and FB-Discharge Module works to switching cycle. The difference between the maximum
discharge the related output voltage through the FB output current and the valley current limit is depended
pin. This will ensure that the output is in a defined on the ripple current of the inductor. It is diagramed by
state next time when it is enabled. Since this is a soft the graph below:
discharge, that there are no dangerous negative
IL
voltage excursions to be concerned about. In order to
maintain the correct function of the soft-discharge IL
Maximum
Average
IOUT
module, the chip power supply must be online.
Current
VOUT Drop Function Limit
Threshold
The GS9238 builds in a Vout voltage drop function
for CCM mode operation. The drop function will Output Over-Voltage Protection
make the Vout voltage deviate the voltage set by FB When the output voltage rises up to 125% of the preset
resistor calculated from 0.8V reference. Different Vin voltage, the internal fault-logic module delays about
and Vout voltage make different drop voltage. The 20us and turns on the low side Power MOSFET. It stays
drop voltage follows the equation below: latched on and the GS9238 is latched off until Power
VDrop  Reset or EN Reset.
 8 V  VOUT 1.2  VIN  1.2 Output Under-Voltage Protection
 30mV  1   IN   
 9 VIN  1.2 VOUT  10.8 When the output voltage falls down to 45% of the preset
 5 mV voltage, the internal fault-logic module will delay about
Output Voltage Selection 20us and turns off both the high side and low side
The output voltage is set by the feedback resistors Power MOSFETs. Both switches stay latched off and
RFB1 and RFB2 of Figure1a and Figure1b. Because of the GS9238 is latched off until Power Reset or EN
the Vout Drop Function, the direct reference should Reset. During soft-start, the UVP will be blanked, until
plus the VDrop. So, the calculation of RFB1 should soft-start procedure finished. The blank time depended
considerate the VDrop voltage. Therefore the RFB1 on the value of the capacitor connected to SS Pin. But if

Rev.:1P8 14 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

the output voltage rises up above the UVP threshold is finished, the PGOOD is pulled high by external
tolerance during the counter period, the UVP counter resistor. In normal operation, the PGOOD window is
is released immediately. from 90% to 125% of the converter reference voltage.
UVLO and Soft-Start When the output voltage has to stay within this window,
An internal under voltage lockout (UVLO) module is PGOOD signal will become high. When the output
used to sense the VCC power supply. The PWM voltage outruns 90% or 125 % of the target voltage,
converter is forbidden by the under voltage lockout PGOOD signal will be pulled low after about 20us delay.
module. When VCC rises about 4.15V, the GS9238 This delay prevent false PGOOD drop.
will initial the control logic circuitries and soft-start External Devices Selection
ramping generator, and then allows switching to For loop stability, the 0 dB frequency (f0), defined in the
occur. When VCC falls down to about 3.85V, the follow equation:
PWM converter is forbidden again. 1 f
f0   SW
When VAIN rises about 5.5V, the LDO output voltage 2  RESR  COUT 4
(VCC) of GS9238 enables and regulates a 5.15V The loop stability is determined by the output capacitor.
voltage. After VAIN falls down to 5.3V the LDO (VCC) Specialty polymer capacitors have COUT in the order of
will turn off. several 100uF and RESR in range of 10mohm is
After soft-start module starting, the GS9238 recommended. However, ceramic capacitors have f0 at
converter will release the current limit threshold more than 700 KHz, which is not recommended.
followed the soft-start ramp. After UVP blanking time, In order for the right regulate manner, the ripple voltage
the output under voltage protection and power good at the feedback pin (FB), should be approximately
indicator is enabled. 15mV. This generates Vripple= (VOUT/0.8) ×15mV at the
FB Short Protection output node. The output capacitor RESR should meet
Because the UVP protection is blanked during the this equation.
soft-start period, if FB pin short to GND, the output The external device selection is list below:
voltage will increase continuously without OVP Choose Feedback Voltage Divider Resistor
protection. It is a very dangerous condition. The Set RFB2=1K~20K ohm
GS9238 build in a safety protection scheme to avoid
 VOUT 
this situation. When soft-start procedure begins, the RFB1  RFB 2    1 
 0.8  VDROP 
GS9238 monitors the SS Pin and FB Pin both, if the
voltage of SS Pin is higher than 240mV and at the Choose RTON
same time the voltage of FB Pin is lower than 80mV, 1 VOUT
TON ( Max )  
after a few micro seconds delay, the fault logic will fSW VIN( Min )
stop the switching cycle and latch on. Only Power on
RTON ( MAX )  (VIN  0.8 )  750K  100K
Reset and EN Reset can release this latch condition.
Power Good Indicator Choose Inductor
PGOOD is actively held low in shut down and Set the ripple current approximately 1/4 to 1/2 of the
soft-start status. During the soft-start process, the maximum output current. 1/3 is recommended. The
PGOOD is an open-drain status. When the soft -start recommended inductor can be calculated from the

Rev.:1P8 15 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

output current, indicated by formula below

3 (VIN(max)  VOUT )  VOUT

LIND  
IIOUT(max)  f VIN(max)

For applications that require fast transient response

with minimum VOUT overshoot, consider a smaller
inductance than above. The cost of a small
inductance value is higher steady state ripple, larger
line regulation, and higher switching loss.
Choose Output Capacitors

1 VOUT
RESR    0.015
I ripple 0.8
3 VOUT
   0.015
IOUT (max) 0.8
VOUT
RESR   75( mohm)
IOUT (max)

Organic semiconductor capacitors or specialty

polymer capacitors are recommended.
The GS9238 support pure MLCC because the
benefit of the internal
Choose Soft-Start Capacitor
When SS ramp rise up to about 1.6V, the chip thinks
the soft-start procedure is over, and then, release the
UVP protection function. At the same time, the VOUT
voltage will reach the target set by the FB resistor
divider. So, the total soft-start time is defined by the
formula below:
1.6  CSS
TSS   1.6 10 8  CSS (ms)
ISS
Where, the unit of TSS is mS.
For example, the typical TSS is equal to 1.6mS with
10nF CSS.

Rev.:1P8 16 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

Package Dimensions, TQFN23-4x4

L2 E1

D1
D2

k
E
E3
D1
D3
E2

L1
pin 1 dot 2 1 L

L1 e b
D

(Top view) (Bottom view)

A
A3
A1

(Side view)

Dimensions in
Symbol Millimeters
Min. Max.
A 0.70 0.80
A1 0.00 0.05
A3 0.203 REF.
b 0.20 0.30
D 3.90 4.10
D1 0.65 0.85
D2 0.85 1.05
D3 1.24 1.44
E 3.90 4.10
E1 2.95 3.15
E2 2.60 2.70
E3 2.95 3.15
L 0.35 0.45
L1 0.57 0.67
L2 0.23 0.33
e 0.50 REF.
k 0.33 0.37

Note

1. Min.: Minimum dimension specified.

2. Max.: Maximum dimension specified.

3. REF.: Reference. Normal/Regular dimension specified for reference.

Rev.:1P8 17 Feb-17
GStek series
NIKO-SEM High Performance Single Synchronous GS9238
GStek series Buck Converter

DISCLAIMERS

Please read the notice stated in this preamble carefully before Admission e accessing any contents of the
document attached. Admission of NIKO-SEM’s statement therein is presumed once the document is
released to the receiver.

Notice:

Firstly, NIKO SEMICONDUCTOR CO., LTD. (NIKO-SEM) reserves the right to make corrections, modifications, enhancements,
improvements, and other changes to its information herein without notice.. And the aforesaid information does not form any part or
parts of any quotation or contract between NIKO-SEM and the information receiver.

Further, no responsibility is assumed for the usage of the aforesaid information. NIKO-SEM makes no representation that the
interconnect of its circuits as described herein will not infringe on exiting or future patent rights and other intellectual property rights, nor
do the descriptions contained herein express or imply that any licenses under any NIKO-SEM patent right, copyright, mask work right, or
other NIKO-SEM intellectual property right relating to any combination, machine, or process in which NIKO-SEM products or services are
used.

Besides, the product in this document is not designed for use in life support appliances, devices, or systems where malfunction of this
product can reasonably be expected to result in personal injury. NIKO-SEM customers’ using or selling this product for use in such
applications shall do so at their own risk and agree to fully indemnify NIKO-SEM for any damage resulting from such improper use or sale.

At last, the information furnished in this document is the property of NIKO-SEM and shall be treated as highly confidentiality; any kind
of distribution, disclosure, copying, transformation or use of whole or parts of this document without duly authorization from NIKO-SEM
by prior written consent is strictly prohibited. The receiver shall fully compensate NIKO-SEM without any reservation for any losses thereof
due to its violation of NIKO-SEM’s confidential request. The receiver is deemed to agree on NIKO-SEM’s confidential request therein
suppose that said receiver receives this document without making any expressly opposition. In the condition that aforesaid opposition is
made, the receiver shall return this document to NIKO-SEM immediately without any delay.

Rev.:1P8 18 Feb-17
GStek series