8.

Level 3 Repair

8-1. Components Layout

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
 SM-A225F_REV01 Block Diagram (BB)
SM-A225F/M
Common
EMMC_D[0:7]
LPDDR4A_DQ([0:15]), DQS
LPDDR4B_DQ([0:15]), DQS
MEMORY
4+64GB
LPDDR4A_CA([0:5]), CLK, CKE, CS, DMI
LPDDRBA_CA([0:5]), CLK, CKE, CS, DMI (KMDH6001DA-B422)
LPDDR4_RST_N

RCAM1_MIPI[0:3]
RCAM1_SENSOR_I2C_1P8
RCAM1_3_4_FCAM_EEP_I2C_1P8
REAR_CAM
RCAM2_MIPI[0] OIS_48M
RCAM2_SENSOR_I2C_1P8 BOKEH_2M
RCAM3_MIPI[0:3] ULTRA WIDE_8M
RCAM3_SENSOR_I2C_1P8
MACRO_2M
RCAM4_MIPI[0:1]
RCAM4_SENSOR_I2C_1P8

FRONT_CAM CAM_OIS_I2C_1P8
FCAM_MIPI[0:3]
FCAM_SENSOR_I2C_1P8
13M

AP_MCU_I2C_1P8
OIS MCU
STM32G051F8Y6TR
MCU_BOOT0_SWCLK
MCU_nRST

CAM_SPI

SENSOR_SPI 6AXIS SENSOR

LSM6DSOTR
6AXIS_INT/INT2

Magnetic SENSOR
SENSOR_I2C_1P8
MMC5633NJ

GRIP1_I2C_1P8 GRIP SENSOR1

ISG5320A
AP GRIP_INT1

MT6769V GRIP2_I2C_1P8 GRIP SENSOR2

ISG5320A
GRIP_INT2

OCTA
MIPI_DSI0_D[0:3]
DISPLAY
TSP_I2C FHD+ 6.4"

BATTERY
FG_SENSE_P/N
USB_AP_D_P/N (USB)
CON
AP_UART_TXD/RXD (UART)
USB_D_P/N, CC1/ 2
FG_IF_PMIC_I2C (I2C) IF PMIC IF CON
WATER_DET
MST_DATA_A/B SM5714
MAIN FLASH

BTP_SPI
FPS SW_ON

OSC
X2U026000B81HBZ-
POWER_KEY
DHPZ
AUD_DAT_MOSI[0:1], AUD_CLK/SYNC_MOSI
AUD_DAT_MISO[0:1], AUD_CLK/SYNC_MISO
PWRAP_SPI0 MOTOR_EN MOTOR
SYSRSTB
SRCLKENA0/1, WATCHDOG, RTC32K_CK
AUDIO CODEC POWER_KEY
POWER KEY
DVDD_PROC_B/PROC_L/CORE/MODEM/
GPU_PMIC_FB/GND
MAIN PMIC RCV CON
RCV_P/N
VOLUME MT6358
VOL_UP KEY VOL_DN

MAIN_MIC_P/N MAIN MIC

SUB_MIC_P/N SUB MIC

AUDIO CODEC
SPK
SPK_I2S3 AMP SPK_OUT EAR_MIC_3.5_P
EAR_OUT_L/R EAR
EAR_MIC_P/N
EAR_L_DET
JACK/MIC
EAR_OUT_FB
 SM-A225F _RF
SP2T
Main1 BGS12P MMMB
2L6 WIPS115749-
ANT
TRX_B

SP10T
5_26
TRX_B1 2R
3G/4G
2_17 LB
LB/MB MXD86
A7S
TX_3G_4G_LB
TX_L
B1

TRX_B GSM
28
Embed TRX_B LB TX_GSM_LB
20 TX_L
ded TRX_B
B3
Couple 8
Coaxial r SP1
TX_GSM
_LB
Cable 0T TX_GSM TX_GSM_HB
TX_M
_HB B3
GRIP TRX_B
1 GSM
IC_2 TRX_B
4_66 HB
TX_3G_4G_MB
TRX_B TX_M
3 B2
TRX_B 3G/4G
2 RFF
HB E1
ANT ANT PRX_B5_26
PRX02
Switch Switch PRX_B12_17
PRX01
MXD85 MXD85
PRX_B28
48E 48E PRX04
PRX_B20
PRX05
Main2 PRX_B8
PRX03

ANT PRX_B1

PRX_B4_66
PRX12
PRX11
HB PRX_B3
PRX08
PRX_B2
PRX07

Embed SFMD3L0 PRX_B7

ded F001 B
Couple 7
B
TX_B7/38/40/41 TX_H
r 4
B
0 B2
4
GRIP A
1
U
IC_1 SP
WIPS33232-
Transceiver
X
RFF
4T E0
01
RFF
E1
High-Band MT6177W/A
PAM
PRX_B38_40_41
PRX09

PDET TXDE

Sub T1

ANT DRX LNA

Bank
LB/MB/ MXD83E4
DRX LNA4_ W
HB SP8T
_B7
DRX_
B40
DRX_B3
IN1
LNA4_
IN2
LNA4_
SP
3T DRX_HB DRX1
MXD86 8_41 IN3
OUT_ 3
MHB
80S LNA3_
DRX
_B3 IN1
LNA3_ DRX_B2_3
DRX
_B2 IN2 OUT_
DRX7
LNA2_ MB2
SP
IN1
LNA2_
SP8 4T DRX_B1_4_66
IN2 DRX1
T LNA2_
OUT_ 1
IN3
LNA2_
DRX_B1 MB1
_4_66 IN4
DRX_ LNA1_
SP
B20 IN3
LNA1_
DRX_ 5T
B8
DRX_ IN1
LNA1_
DRX_LB
B5
DRX_ IN2
LNA1_ DRX4
OUT_
B28
DRX_B1 IN5
LNA1_ LB
2_17 IN4

ANT ANT DRX_B8

_2nd DRX2
Switch Switch SP2T
MXD8548 MXD8548
MXD86
EC EC
21E

WiFi GPS
ANT ANT

GPS_RFIN
PRX
GPS_R
13FIN

WiFi/BT/GP
S/FM
MT6631N
/B
WB_RF_2G
RF
2G
RF
5G

FM_ANT
FM_LANT
_P/N

SM-A225F/M
Common
 Model : SM-A225F
Revision : REV02
Manufacture Count : 400EA
Charge : 권순각
Contact : 010-3906-3247
Date :
Routing :
Resin :

VX_SETUP(2021-04-23)_HHP
Created date of PCB data : 2021/4/29 12:09:49

MIC6000
U3000
C3078

C3002

C3076
C6027

R3001
R6005
ZD6005
R6028

C6028
ANT2000 U3005
R3003

L6012 C7003 R7005

C6029
C2015 C7002

C2027

SOC7002
C2028

C2033

U2003
L2013 ANT2003
C2036
L2017

L2021

L2028

C2029

SIM5003UP
C2037
L2014

L2018

C2040
C2032

C2025

C2021
C2064
F2005
C2034

C2030

C2026

F2003 U2004
L2015
C2065 L2009 L2000
L2024
C2091

C2041
L2035

L2029 L2011 C2006

L2022 L2026
L2010
F2007
SIM5002

F2002
F2004
C2022
C2045

C2093

F2000
L2023

C2092 L2027
L2002

L2007

C2089 L2025

C2016
C2004

C2017

C7001

F2001

SIM5001 SIM5000
C2012

U2007 C2073
L2030
F2006
C1070

C2076
C2079

C2082
C1071

C2080

C2085
C2070

C2069

C2077

C2086

C2083

C2088

TP3008

TP3007 TP3002 TP_USART2

R5038
R5041

TP7000
R7016
C5159 C5153 TP3006 TP3005

SC7004
U7002

U3006
U7013
R7019

C7017
U7000

C7000

C7027

C3029 C3034
TP_USART1
C7075
C7020

C7037
C7019
R7003

R7018

C7022 C7041
C7028
U7003

R7023

C7025 C7014
U3010

R7022
C7026

C3070

C7015

SM-A225F/M
TP_3002

R4005
C3069
C7021

R4007
C7023 C7016

Common
SC7003
C7044

C7043

C7042

C5123

CN7000
C5107
C5163

C5162
L5015

L5014

C5035
C5156

C5155

C5125

C5127
C5124

C5138

R5033

R5032

R5040
C5131
C5109

C5095

C5134

C5136

C5128
C5161

C5133

TP4005

C5160 C5139
TP_CAM1_CLK_P
TP_CAM1_D0_P

TP5005
R4030

C5014 R7002
R4016

R5039 R4039
TP_CAM1_CLK_N
R6002

R6001

TP_CAM1_D0_N

TH4000
R7004
C7013

C7008

R7006

R7001
C7033

C7004
L7007

L7006

R4034
C7055 L7008
C4020 TP5004 U7001

C7063 C7034 C7036

UME500
HDC4000

C7064
TP_SYSRSTB

C5118

C4070

SOC7000
C7061
R4002

C5115

C7048 ZD5001
C7062
U7010
C5145

L7005 C7038
ANT5002

C7066
C5062
C5144

C7047
C7067
L7009

C7050

UCP4000 C5061
C5147
R4009
R5045

R5044

C4037
C7068
C5143

R4011

C7052 C4077
L5008

C7054
C5053

C5074
C5059
R4037

C2002 C7065
ANT5000

C4073
C7051 C4050 C5117 C5072
L7010
C2003

U2000 C4078 C4000 C5114

C7046
R7011
C5034
C5116

C7056
C4074

C4002
U7004

C6001
U5000
TP_WS TP_DO TP_DI

D5003 C4011 C5110 C5030

L6000
R5010
ZD6000

TP_BCLK
C5060 R5003
C6005
C5033

C5157 R4040 C5029

ANT2001

ANT5001

L5003
C7045

R4035 R5046
C5158
TH4001

C6003 R4012
R4032
D5000
R5037

ANT5004 L5009
R4014 C5024

C6006 U6002
R6000

R4036

C5076 R5008 R5007

C6002 R4000 R5009
R5027 C5077
R5042

R5004

R5005

TP5006
C4032

C4048
C4044

C4023
C4024

C4033 C4031 TP_MST_DATA_B TP_MST_DATA_A TP_EMMC5000

TP_WATCHDOG
L5010

C7060
C7070

C5081 R4013
TP_INTN

C4035 R5036 R5035 C5078

R6007
C6010 TP_RST
TP_TSP_7000
TP7002 C7059
R4001
ZD5005
R7013
R4033

C5064

C5063
C6004

R5028
C5126

C5119
R5043

C5142

C5135

C5137

C5121

C5120

C5122

C5141

C5129

R5011

R6016
R5034
C5132

C5130

C5149

ANT5005
C5140
U7006
U6000

U7008

C5073 C5150 C5151

TP5002

R6010
L6001

L6002

ZD6002 ZD6001 C5146 ZD5003

Q6000
U7012
R7024

R4006

R4003

C5075 C6011
TP_SRCLKENA5001
R6004

R6003

R5031
ANT2002 R6011 U5003 ZD5004
C6009 R6013 D5001
C6000

C6007

R4038 TP5003
R4004 C5148 R7017

C7069 C7058 C7057 R6012

GND

BOOT1

VBUS

ID

JTAG4001 JTAG4002

JTAG4003
 Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :

VX_SETUP(2021-04-23)_HHP
Created date of PCB data : 2021/4/29 12:09:49
L2012

C2001 C2024 C2023

ANT2004

ANT2005

ANT2006

L2001 C2000
ANT3003

ANT3004
C2031
U2005

L2016
C2005

L2019
C2035
U2002

L2003

C3016
C2009
C2020
L2005 C2039 L2020
L2004 L3017
C2013

L2008

C2008

C3023

C3018
C2018 C2007 C2014

L3012 C3000 L3001

L3004

L3003
C3051 F3003
U3001

C3037

C3031

L3008
C3028 L3009 L3010

C3021
L3007

L6009 L6010

ZD6003

ZD6004
ANT6000 ANT6001 U3008

C3045
C3052
C6019 C6026
C3006 U7011 TP1000
L3015
SOC7003

C3001

L3002
L3000

L3011

L3006

L3016
SOC7004

C3007 C3044

C3003
C3046
C2042

C2078

C2087

C2084

C2090

C2081
L2031

L2033

L2032

L2034
R2002
C7018

C7030
C2047

C2046

C2049

C2044
C7029

L2006
TP_TOP_DATA

C2053

C2051

C2050
TP7001 C2059 C2057 C3013

R2001

C2011
R7009

C3047
R4008

C3043
L3005
TP_TOP_CLK

R4010

C3049
U3003

C3048

U2001
C3050
C1057
OSC5000
C2048

L1061 TP_BT_DATA

L1009
C1058 TP_BT_CLK

U2006
C2075 C1003
C2038
SC7001

L1006 TP_WB_CTRL1

C1011 TP_WB_CTRL2

C2074 L1022

C2010
R2000

L1082
C2043

L1021 TP_WB_CTRL0

C2072 L1018
C5097

C1010
C2067 L1017

L1066
L1067
C2071 C1102
C1081

C1080
F1010 C1084 C1079 C1083 C1065
R1005 C2068 L1081
C7031

R7012

R1006
C1087

L1073

L1077 C1059
PAM1001
C2058

C2056

C2055

C2054

C2052

C2060

C2061

C2062

C2066

C2063

C1022

L1034
C7032

C5091

R5017
L1076
U1002 C1060
C7035

C1064
L1063

L1065
C1086
C1039

C1046

C1029

C1082

C1006
L1050

L1037

L1035

L1007

L1020

L1008

L1033

C1090
C5007

C7039

L5013
C1091 C1098
C5018
C1023

C1005
L1010

L1023

L1019

R1007
C1024

C1094
L1036

TP3001

R5021 R5047 R5026

C5099
C5020

C5090
C5019

C5003

C5002

C5004

C5010

C5021
C5038

C1097
C5008

R5024

F1004
C5086
C5009 C5017 R5016 C1021 C1004
ZD1001
C1109

C5079
R1003
C5092

C5039

C5040

C5037

C5001

C5013

C5000

C5016

C5011

C5012

C1103

C1106
C1101
SC7000

C1045

C1105

C1099

C5057
R5025 C5080
C6024 C1100
TH1000
R5014
RFS1000
R6024

R6017

C1056

R6006 L1045
C1104

C1095

C1096
L1078

L1080
C5036
C6022

L6008

L1015
C6025

C1033 C1032 L1079

C1035 C1044
C5044
R5015

C1007

L1075
C1088

F1003
C5068

R6023

L1044
C5089
R6025 C1089 F1006 C1075

F1000
PAM1000
C1034

C1107
C5113

C1085

C5067
L1072

L1074
L6007

C1008
C5069
C5043

C1000

C1014

L1014

C5066
C1072

L1004 L1030 L1011 L1012

U5002
C5070 C1038
R5006

C1053

C1052
L1055
C5106

L1048

L1047

L1046

L1001 L1026 C1108

C1037

L1049

C5071
C1074

L1039

L1062
C1027

L1040
L1042

R1004
C5085 C5028
C5046

C1026

C1050 C1047
L1027
U1000
U1001

L5006
C1067 C1063
C5058
C5056

SM-A225F/M
F1007

C1092
C5065 C1013 L1053
C1028

L1043

L1041

C1062 L1060
C1093 C1036
L1031
L5004
C5045

C1049

C1041

L1051

C1040
L1054

C1015

C1009

C1002

C1001 L1000
L1032

L1028

L1002

L1016

L1013

ANT1001
C5100

L1005 L1003

Common L5011
C1054
L1056

L1057

C1048
F1002
F1001

F1005
F1008

C1019
C1042
L1052

C5047 C5048 C5049 C5050

C5042 C5104
L1025
C1076

L1070

L1071

R5023 C1018
C1043
L5000

C5082 C5098
L5012

C1073

C1069

C1078
C1055
L1058

L1059
L5001

L5005

R1000
L5007
BH7000

C1051
C5094
C1068

L1068

L1069

L1064

C5084 C1031 C1030 C1061 C1066

C7049

C1020

SOC7001
U7005 C5093 ANT1002
C7040
C5083
C1017

C1016
L1024
R7015

C7053

R7000 C5179
L5002

C1077
C7012
R5013 C4019

C7007 C5025 C5176

C4051 C5051 C5022 C5175
R5012

R5020

C7024
C7009

C7006 C7005 R4022 R4021 C1025

C4047
C5088
ZD1000

C5054 C4045
LED5000

R1001

R1002

C5055
C3095 C5052
C5102
R3000
C3098

C3099

Q5000

C5026
C5096

C5032
C4008

L1038

R3010 C3097 C3102

ANT3006

C4006
ANT3005

C4013 C4014 C4054

C4053

C4018
C3096 C3107 L1029 C1012

CN7001
C3100

R3011
R5018

R5019

R5022
C5101

C5006
C4030

C4016 C4064 C4063 C4007

C3004

L3013 C4012
L3014
C4004
C4017

C4069
C5164 L5016
C7011

C7010

C4036 C5087
C4027 C4015
R5029

R5030
C3039
C3035
U3002

C4021

C4029 C4010
C4052

C3092 C4005 C4001

C5005
TP_NFC_EN

C4028
U3004

R4025
R5048

R5000

R7007
C3086 C3005 C4009 C4071
R4026 C3094 C4003 C4026 C5015

U3007 RFS1001
C3093
U5001

ZD5000

C5103
R7010
C6017
R6018

C6008
L6004

C6018
TA3000

C5023

C5108
C5105
C5152

C5183 L6005
TP_NFC_FIRM
TP3000

TP3003

C4049

C5027
C5172

C5041

C5031
C3104

R7014
C3032

C6020
TP3004

TP3009

C3084 TP_RTC5000
C4022 C4046
C3008 C4034
TP_NFC_CLK_REQ
C3009

C3087
TP5015

TP5016
TP5014
TP5013

ANT3001
ZD4002

C3022

TP_NFC_IRQ

R7021
TP_RFFE3_DATA

TP_RFFE3_CLK

TP_EL_ON6001 TP_EL_ON6000 TP_DISP_TE

R7020

SOC5000
TP5000

TP5001

TP_UB1 TP_UB0
ANT3000

U6001
C6015

TP_SRCLKENA5000

C6013
R5002

C6016

SOC6000
C6012
D6000
R5001

SOC5001
TP5018

TP5017

R6015

R6014

C6014
USB_DN

USB_DP
8. Level 3 Repair

8-3. Flow chart of Troubleshooting.

Oscilloscope Digital Multimeter

Power Supply + driver, ESD Safe Tweezer

8960 & Spectrum Analyzer Soldering iron

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-1. Power On

Mobile phone does not power on.

Yes
No
Charging the battery by TA.
No If its voltage level is extremely low
Check the Battery Voltage.
Is it more than 3.8V? (under 3.0V),
Change the battery.
Yes
No

Power-on the phone and check Yes

the power-on sound
Change the FRONT-LCD ASSY
or motor Vibration.
Sound or Vibration is ok?

No

Check the voltage level at No

R5011 while pressing power Replace the Power key FPCB
key. Is the voltage high?

Yes
No
Check the output voltage of U5002
L5006>1.35V, L5004>2V, L5002>0.5V
No and other LDO Voltage
Check the signal of
VDD_A_1P2=1.2V If the output voltage is not normal,
Change the U5002
※ Each voltage level has ±10% margin

Yes
No
No
Check the Clock OSC5000 Replace the OSC5000
Is the frequency 26Hz? ※ Test condition (Oscilloscope setting)
: 20.0us.div (time division)
Yes
No

Check the initial operation

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-2. Initial

Initial Failure

Yes
No

Re-download latest SW on the

mobile phone

Abnormal
No
Abnormal Check the OSC5000
Re Check "Power on" (Crack, open etc.)
Trouble shooting process Check the U5002 (Crack etc)

Normal

Change U5002

Abnormal

Change PBA

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-3. No Service

No service

Yes
No

Home screen → Phone → CP : A325XXXXX

Keypad → *#1234# → Check
Check the connection of RF coaxial cable
Phone version → CP :
A325XXXX or unkown

Unknown

Check the Voltage No

C2021/C2025/C2022/C2026 : 1.8V, Replace the U5005
C2023/C2024 : 1.2V

Yes
No

No
Check the clock OSC5000
Is the frequency 26MHz? Replace the OSC5000

Yes
No

Replace the U2005

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-4. SIM Part

Insert SIM card

Yes
No
No
Is SIM socket ok? Replace SIM socket

Yes
No Change to the new SIM card.
No If it doesn`t still work SIM card after
Check the SIM Voltage.
= 1.8V (R5038)? changing Check the U5002
(Crack etc)

Yes
No

No
Check the SIM RST / IO / CLK.
(SIM1 : C5156(1,8V or 3.0V)) Check the UCP4000 (Crack etc)
(SIM2 : C5153(1.8V or 3.0V))
Is signal ok?

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-5. T-Flash Part

Insert T-Flash card

Yes
No
No
Is SIM socket ok? Replace SIM socket

Yes
No
Change to the new T Flash card.
No
Check the T-flash Voltage. If it doesn`t still work T Flash card after
(C5160) = 3.0V? changing Check the U5002
(Crack etc)
Yes
No

Check the t-flash No

CMD /Data/CLK.
Check the UCP4000 (Crack etc)
Is signal ok?

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-6. Cable Charging Part

Insert TA / USB

Yes

No
Charging Sequence Start
VBUS_OVP(C6016) = 5V or 9V Replace SUB PBA

Yes

No

Check the
VBUS_IF(C6015)=5V or 9V
Replace U6001

Yes

No
Battery is Charging? Replace U5000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-7. OTG

OTG does not work

Yes

No
Check the Check U5000
VBUS_IF(C5024) = 5V (crack, open, damaged, etc.)

Yes

No
Check the Check U6001
VBUS_OVP(C6016) = 5V
(crack, open, damaged, etc.)

Yes

No
Check OTG working ? Replace SUB PBA

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-8-1. Accel Sensor(6 AXIS)

Accel. Sensor does not work

Yes
No
No
Check the voltage
C3029 =1.8V Replace U3010

Yes
No
No
Check TP3009, TP3003 Replace U3006
(I2C, CLK is OK?)

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-8-2. Fingerprint Sensor

Fingerprint Sensor does not work

Yes
No
No Reconnect.
Check the Fingerprint Sensor
connector If broken, Replace the Sensor FPCB and
Do calibration.

Yes
No
No
Check The voltage
C5015 =3.3V Replace U5001

Yes
No
No
Check the Fingerprint Sensor
MISO, MOSI, CLK, CS_N Pins Check SOC5000 Connector,
(SPI is OK?)

Yes
No
No
Check Fingerprint working? Replace the Fingerprint sensor module

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-9-1. Microphone Part - Main MIC

Check main microphone function

in voice call Handset mode or voice recorder
mode
Yes
No

Check the voltage of C1028

No
at SUB PBA = 1.9V replace SubPBA

Yes
No

No
Check the MAIN_MIC_P data
at SubPBA L1022 Replace MIC1000 at SUB PBA

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-9-2. Microphone Part - Sub(2nd) MIC

Check Sub(2nd) microphone function

in voice call loudSPK mode
or in camcording mode
mode
Yes
No

Check the voltage at No

Replace U5002
L6027 = 1.9V

Yes
No

Check the No
SUB_MIC_P data at Replace MIC6000
L6005

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-10. Speaker Part

Check speaker function.

Play MP3 with maximum volume level.

Yes
No

Check C-clips of Sub PBA No

ANT1003, ANT1004 Replace C-Clip

Yes
No

Yes No
Check the PWMNo
output at Replace SUB PBA
ANT1003, ANT1004

Yes
No
No
Check the output of VDD_AMP(C6002) Replace UCP4000 on MAIN PCB

Yes
No

Replace speaker module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-11. Receiver Part

Check receiver function

in voice call receiver mode

Yes
No

Check RCV module No Resolder or Replace

where RCV's placed
for any damage ANT6000, ANT6001

Yes
No

Check the signals on No

RCV_P, RCV_N Resolder or replace U5002

Yes
No

Replace RCV module

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-12. BT/WIFI

BT/WIFI is not working

Yes
No
No
Check BT or WIFI function ON Enable BT or WIFI function.

Yes
No
No
Check the antenna contact 1. Resolder or replace ANT3004
ANT3004 2. Replace REAR

Yes
No

Check the voltage No

C3047 = 1.8V, C3048 = 1.8V, Replace
C3031 = 1.8V, C3003 = 1.8V U5002
C3013 = 2.8V
Yes
No

Yes
No

No
Check the status of U3008, C3018, Resolder or replace the wrong element
L3004, C3008, L3000 (open, crack, deviation, etc)

Yes
No

Resolder or replace U3003

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-13. GPS

GPS is not working

Yes
No
No
Check GPS function ON Enable GPS Function in the setting.

Yes
No
No
Check the antenna contact 1. Resolder or replace ANT3003
ANT3003 2. Replace REAR

Yes
No

Check(crack,open,etc)
C3031 = 1.8V, L3008=1.8V No
C3046 = 1.8V Resolder or replace the wrong element
U3001, F3003, C3000, C3027, L3009 (open, crack, deviation, etc)
C3028, L3011

Yes
No
Resolder or replace U3003

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-14. NFC

NFC is not working

Yes
No
No
Check NFC function ON Enable NFC Function

Yes
No
No 1. Resolder or replace ANT3005, ANT3006
Check the antenna contact
ANT3005, ANT3006 2. Replace NFC ANT

Yes
No

Check the voltage on No Check U5002

C3004 = VBAT, C3084 =1.8V,
(crack, open, damaged, etc.)
C3094 = VBAT

Yes
No
No
Check 26MHz Clock at C3004 Check U5002, OSC5000

Yes
No

Check the status of

Resolder or replace C3097, C3100,
C3097, C3100, R3010, L3014, No
R3010, L3014, L3013, R3011, C3096,
L3013, R3011, C3096, C3107,
C3107, C3095, C3012, C3098, C3099,
C3095, C3012, C3098, C3099,
R3000
R3000

Yes
No

Resolder or replace U3004

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-15. FM radio part

FM is not working

Yes
No
No
Check the FM function Enable FM Function.

Yes
No

Check the voltage of No

C3043 = 2.8V Resolder or replace U5002
C3013 = 2.8V

Yes
No

Check the voltage of No Replace SOC6000 at Main PBA or

C1016 = 1.8V SOC1000 at SUB PBA or CtoC connector
at SUB PBA

Yes
No

No
Check the status of L3006 Resolder or replace L3006

Yes
No

No
Check the status of C1014, L1017, Replace SUB PBA
ZD1006, L1016 at SUB PBA

Yes
No

Resolder or replace U3003

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16. Display

LCD is still off after PWR ON

Yes
No

Check the MAIN FPCB

Yes
No
No
Check the connection of Reconnect the SOC6000
SOC6000

Yes
No

Check
VDD_LCD_3P0 = 3.0V (C7057) No Resolder or Replace the U7006(3.0V)
VDD_LCD_1P8 = 1.8V (C7058) Resolder or Replace the U7008(1.8V)

Yes
No

Check No
VDD_LCD_ELVDD 4P6 = 4.6V (C7055)
VDD_LCD_ELVSS_-4P4 = - 4.4 ~ - 1.4V (C7056) Resolder or Replace the U7010
VDD_LCD_ELAVDD_7P6 = 7.6V (C7038)

Yes
No

Replace the Display module

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-17. REAR Camera

“Camera” function does not work

Yes

No
Check the Camera connector on Main
Reconnect the SOC7000, SOC7001, SOC7002,
PBA
SOC7003

Yes

Check the voltage

C7019 : 1.1V
No
C7021 : 1.8V, C7075 : 2.9V Resolder or Replace U7001, U7003, U7004, U7005,

C7025 : 2.8V, C7036 : 1.8V U5002

C7053 : 1.8V, C7046 : 3.3V

Yes

No
Check the CAM_MCLK
Replace the PBA
C7008, C7013, C7004

Yes

Replace the camera module

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-18. FRONT CAMERA

“Camera” function does not work

Yes

No
Check the Camera connector on Main
Reconnect the SOC7004
PBA

Yes

Check the voltage No

C7029 : 1.8V Resolder or Replace U7003

C7018 : 1.2V

Yes
No
No
Check the VTCAM_MCLK
Replace the PBA
(C7033)

Yes

Replace the Front camera module

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-19. Motor

Motor does not work

Yes

No
Check the Clip Resolder or Reconnect
ANT5004 and ANT5005 ANT5004 , ANT5005

Yes

No
Check C5158 and C5157 Resolder or Replace
(crack,open,etc) C5158, C5157

Yes

No
Resolder or Replace PMIC CHIP
Check the voltage C5010 =3.3V Replace : U5002

Yes

Replace Motor

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-20. GSM 850/900/1800/1900, WCDMA B1/2/4/5/8,

LTE B1/2/3/4/5/8/12/17/20/26/28/66 PRx

It is not catching the channel

in normal condition

YES

Check the SUB PBA and coaxial cable NO

(ANT1000~RFC1000, ANT1002, Replace SUB PBA or coaxial cable
ANT1005, U1004, U1002)
Is it ok? (SUB PBA)
)
YES

Check common RX path any damage NO

(RFS1000~U1000, Resolder or replace
U1000~PAM1000~U2006) RX path components
Is it ok?

YES

Check U1000, U2006 NO

Resolder or replace
any damage
U1000, U2006
(Crack, open, etc), is it ok?

i
YES

Change the board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-21. LTE B7/38/40/41 PRx

It is not catching the channel

In normal condition

YES

Check ant path any damage NO

Resolder or replace
(ANT1001,1002 ~ RFS1000)
Is it ok? Antenna path components
)

YES

Check common RX path any damage NO

(RFS1000~U1002,U1002~PAM1001~U2006) Resolder or replace
Is it ok? RX path components

YES

Check U1002, PAM1001, U2006 NO

Resolder or replace
any damage
U1002, PAM1001, or U2006
(Crack, open, etc), is it ok?

i
YES

Change the board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-22. GSM 850/900/1800/1900, WCDMA B1/2/4/5/8,

LTE B1/2/3/4/5/7/8/12/13/17/20/26/28/38/40/41/66 DRx

It is not catching the channel

In normal condition

YES

Check ant path any damage NO

Resolder or replace
(ANT2004, ANT2005, ANT2006~U2003)
Is it ok? antenna path components
)

YES

Check RX path any damage NO

(U2003~U2007 ~U2006) Resolder or replace
Is it ok? RX path components

YES

Check U2003, U2007, U2006 any damage NO

(Crack, open, etc), is it ok? Resolder or replace
U2003, U2007, U2006
i

YES

Change the board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-23. GSM 850/900/1800/1900, WCDMA B1/2/4/5/8,

LTE B1/2/3/4/5/8/12/13/17/20/26/28/66 Tx

It is not catching the channel

In normal condition

YES

Check the SUB PBA and coaxial cable NO

(ANT1000~RFC1000, ANT1002, Replace SUB PBA or coaxial cable
ANT1005, U1004, U1002)
)

YES

Check TX path any damage NO

(RFS1001~U1000, U1000~PAM1000) Resolder or replace
Is it ok? TX path components

YES

Check TX path any damage NO

Resolder or replace
(PAM1000~U2006)
TX path components
Is it ok?
?

i YES

NO
Check U1000, PAM1000, U2006
Resolder or replace
any damage
U1000, PAM1000, U2006
(Crack, open, etc), is it ok?

YES

Change the board

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-24. LTE B7/38/40/41 Tx

It is not catching the channel

In normal condition

YES

Check ant path any damage NO

Resolder or replace
(ANT1001,1002 ~ RFS1000)
Is it ok? Antenna path components
)

YES

Check TX path any damage NO

(RFS1000 ~ U1002, U1002 ~PAM1001 ~ Resolder or replace
U2006) TX path components
Is it ok?

YES

Check U1002, PAM1001, U2006 NO

Resolder or replace
any damage
U1002, PAM1001, U2006
(Crack, open, etc), is it ok?

YES

Change the board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.