Waco Regional Airport ● P.O.

Box 5500 ● Waco, Texas 76708

Beechcraft King Air 90 Series

AUXILIARY FUEL

INSTRUCTIONS FOR CONTINUED

AIRWORTHINESS

ICA Manual No. 26005-30

Revision 2
January 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

RECORD OF REVISIONS
Rev. Rev. Rev.
Date Inserted By Date Inserted By Date Inserted By
No. No. No.

When a revision to this manual is issued, insert the revised or added pages into the manual. Record the revision
number, date inserted, and the initials of the person responsible for the update on this page.

MANUAL No. 26005-30 Rev. 1, 09/01/14

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

MANUAL No. 26005-30 Rev. 1, 09/01/14

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

REVISION LOG
Rev. Rev. Page(s)
Change Description
No. Date Affected
1 9/1/14 ADD KING AIR 90 SERIES ELIGIBILITY. ALL

2 JAN. 2021 INTRODUCTION - UPDATE GENERAL INFORMATION. 1-3

CH. 4 - UPDATE AW. LIM. FORMAT; ADD BEECHCRAFT MANUAL REF. 5

CH. 5 - UPDATE INFO., FORMAT & INSPECTION TIMES SIMILAR TO KA200/300. 7-10

CH. 11 - UPDATE INFO.; ADD PLACARD ILLUSTRATIONS. 11-13

CH. 12 - ADD FUEL SYSTEM DETAILS; ADD LANDING GEAR SERVICING. 15

CH. 28 - ADD SECTIONS GENERAL, CONTENTS, DESCRIPTION AND OPERATION, 19-31
FILLER CAP INSP., FUEL SCREEN CLEANING, LEAK REPAIR, MATERIALS, AND
INDICATOR REMOVAL & INSTL.; ADD VENT BLOCKAGE TO TROUBLESHOOTING;
ADD DETAILS TO FAIRING REMOVAL & INSTL. (WAS CH. 54), FUEL SCREEN INSP.,
REMOVAL & INSTL., CHECK VALVE INSP. & REPL., TANK INSTL., LEAK TEST,
FUNCTIONAL TEST, AND OPTICAL LEVEL SWITCH REMOVAL & INSTL.; ADD AMBER
LED TROUBLESHOOTING INFO.; ADD FIGS. 4 & 5.

MANUAL No. 26005-30 Rev. 2, Jan. 2021

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

MANUAL No. 26005-30 Rev. 2, Jan. 2021

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

LIST OF EFFECTIVE PAGES

Rev. Rev.
Section Pages Date Section Page Date
No. No.
Title Title 2 1/21
Record of Record of
1 9/1/14
Revisions Revisions
Revision Revision
2 1/21
Log Log
List of Eff. List of Eff.
2 1/21
Pages Pages
Introduction 1-4 2 1/21

Ch. 4, AW
5-6 2 1/21
Limitations
Ch. 5, TL/
7-10 2 1/21
Maint. Checks
Ch. 11, Plcds.
11-14 2 1/21
& Markings
Ch. 12,
15-16 2 1/21
Servicing
Ch. 24,
17-18 2 1/21
Electrical Pwr.
Ch. 28, Fuel 19-32 2 1/21

Apdx. A,
Illustr. Parts A1-A38 1 9/1/14
Catalog

Apdx. B,
Wiring
B1-B12 1 9/1/14
Diagram
Manual

MANUAL No. 26005-30 Rev. 2, Jan. 2021

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

MANUAL No. 26005-30 Rev. 2, Jan. 2021

 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

INTRODUCTION
GENERAL
This ICA Manual provides the Instructions for Continued Airworthiness (ICA) for Beechcraft King Air 90 series
airplanes modified by CenTex Aerospace’s (CTA) Saddle Tank STC. The Saddle Tank STC modification
installs auxiliary fuel tanks, called “saddle tanks,” on the wing, behind each engine nacelle as approved under
FAA Supplemental Type Certificate (STC) number SA11142SC.

ASSOCIATED DRAWINGS
The following CenTex Aerospace drawings are provided to install the auxiliary fuel tanks on the airplane. These
drawings are listed as reference and are not required for maintaining the continued airworthiness of the airplane.
Contact CenTex Aerospace for assistance in obtaining a copy of a specific drawing.

Number Title
26005-2000 INSTALLATION, AUXILIARY FUEL TANK
26005-3000 INSTALLATION, NACELLE FAIRING, AUXILIARY FUEL TANK ASSEMBLY
26005-4000 INSTALLATION, FUEL SYSTEM MOD., AUXILIARY FUEL TANK ASSEMBLY
26005-5001 WIRING DIAGRAM, FUEL LEVEL INDICATION, AUXILIARY FUEL TANK
26005-6000 INSTALLATION, FUEL LEVEL INDICATION, AUXILIARY FUEL TANK ASSEMBLY
26005-7000 INSTALLATION, PLACARDS, AUXILIARY FUEL TANK ASSEMBLY
26005-8000 TANK REMOVAL & NACELLE SKIN REINSTALLATION

DESCRIPTION OF MODIFICATION
The Saddle Tank STC installs a set of the following saddle tanks on the airplane:
 90-gallon full fuel tanks (ST180 tanks)
The aluminum auxiliary fuel saddle tanks are mounted on the upper wing behind the engine nacelles. The
saddle tanks are secured to the upper wing structure with five (5) AN4 (1/4 inch dia.) bolts and the existing
nacelle structure with sixteen (16) AN525-832 (#8) screws. An aluminum fairing between the engine nacelle
and tank provides a smooth transition for air flow around the saddle tank. An door on top of the fairing provides
access to the nacelle tank filler cap.
Exterior placards mark the saddle tank fillers, nacelle filler access, and fuel drains added for this conversion.
The existing fuel system is modified so that fuel from the saddle tank can gravity feed into the ship’s center
section fuel tank. A fuel supply line at the bottom of the saddle tank goes through the landing gear wheel well
and connects to the fuel line located between the main wing interconnect line and the nacelle tank, downstream
of the interconnect check valve. See Figure 1 on the next page for the modified aircraft fuel system schematic.
See Figure 1a on the next page for a layout of the saddle tank fuel system. A smaller check valve in the saddle
tank fuel line prevents fuel from migrating back into the saddle tank. Drain valves in the saddle tank and the
fuel supply line (aft wheel well area of nacelle) allows the tank to be sumped and drained.
The auxiliary fuel saddle tanks each have an inlet and outlet vent line protruding up from the tank floor. The
vent lines open at the top of the expansion space in the tank near the fuel filler adapter. The saddle tanks vent
through the ship’s fuel vent system. The saddle tank vent lines connect to the existing vent lines behind the
main spar in the main landing gear wheel well.

PAGE 1
MANUAL No. 26005-30 INTRODUCTION Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL
UNDER BOOST PRESSURE

SUPPLY (EXISTING TANKS) AUXILIARY FUEL TANK

(90 GALLONS USABLE)
SUPPLY (AUXILIARY TANK) VENT

RETURN

VENT LINES

FUEL PUMP F
CHECK VALVE NACELLE TANK
(57 GALLONS
F FUEL TANK FILLER USABLE)

D ISOLATION DRAIN VALVE

90 GAL

VENT

57 GAL D

F D
40 GAL
SUMP &
FLUSH
DRAIN
VENT

25 GAL 23 GAL
40 GAL
CENTER
SECTION
WING TANK
D
NEW
WING TANKS TEE NEW DRAIN VALVE
(TOTAL 128 GALLONS USABLE) NEW CHECK VALVE
VENT

Figure 1. Fuel System Schematic

FUEL TANK
VENT LINE
(OUT)
FUEL TANK

EXISTING
CHECK VALVE
FUEL TANK
VENT LINE EXISTING FUEL LINE
(IN) FROM WING TANKS
FUEL SCREEN

EXISTING VENT LINE

FWD
FUEL LINES

45° FITTING ACCESS DOOR

CHECK VALVE & FUEL DRAIN LINE
FUEL LINES WHEEL WELL

Figure 1a. Fuel System (LH side looking inboard)

The saddle tanks each include five optical fuel level sensors connected to an indicator unit mounted to the
pilot’s side wall. The indicator has five LED indicators for each tank, corresponding to an individual level sensor.
When fuel is at or above the indicated level, the LED illuminates green. As fuel drops below each level sensor,
the LED extinguishes with the exception of the last LED, which changes from green to amber.
Refer to the individual chapters in this manual for additional details and illustrations of saddle tank components
and systems.

PAGE 2
MANUAL No. 26005-30 INTRODUCTION Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

MAINTENANCE
Airworthiness limitations, inspection procedures, servicing information, and maintenance procedures provided
in this manual apply to the equipment and modifications associated with this STC and supplement the
Beechcraft King Air 90 Series Maintenance Manual (AMM). For King Air 90 series aircraft modified by this STC,
follow the inspection, servicing, and maintenance procedures in the AMM, except as provided herein. This
manual uses the same chapter numbering and general format as the AMM.
For standard aviation maintenance practices, such as cutting, splicing, and replacing wire, routing and securing
lines, inspecting electrical wiring and equipment, etc. use the techniques and practices found in FAA Advisory
Circular AC 43.13-1B/2B or later FAA approved revision.

REPLACEMENT PARTS
Appendix A of this manual includes illustrated parts lists for the equipment specified herein. Contact CenTex
Aerospace for replacement parts.

WIRING DIAGRAMS
Appendix B of this manual includes wiring diagrams for the systems specified herein.

MANUAL UPDATES
A copy of this ICA Manual is provided with the STC upon installation. When changes to this ICA Manual are
made, CenTex Aerospace will provide updates to the registered airplane owner by email or direct mail. Contact
CenTex Aerospace to make other arrangements. If there is a change in airplane ownership or operator, please
notify CenTex Aerospace in order to keep all contact information current.
The changes to the ICA manual will be identified by revision number and date in the Revision Log. CenTex will
provide the owner with the revised pages, a Revision Log, and an updated List of Effective Pages. The owner,
or responsible party, will add or replace the pages affected by the revision and make an entry in the Record of
Revisions in order to document the update to the ICA Manual is accomplished.

ASSISTANCE
For assistance with continuing airworthiness issues or any other issues related to this STC, contact Centex
Aerospace at the following address or telephone number.
Centex Aerospace Inc.
7925 Karl May Drive
Waco, Texas 76708
(254) 752-4290
http://www.centex.aero/

PAGE 3
MANUAL No. 26005-30 INTRODUCTION Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 4
MANUAL No. 26005-30 INTRODUCTION Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 4

The Airworthiness Limitations section is FAA approved and specifies maintenance required
under §§43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program has
been FAA approved.

Beechcraft King Air 90 airplanes with CenTex Aerospace auxiliary fuel saddle tanks installed under STC
SA11142SC have no changes or additions to the original Airworthiness Limitations established by Beechcraft.
For airplane component life limits or structural inspections, refer to the applicable Beechcraft manual.

PAGE 5
MANUAL No. 26005-30 CHAPTER 4 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 6
MANUAL No. 26005-30 CHAPTER 4 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 5
TIME LIMITS/MAINTENANCE CHECKS
GENERAL
The overhaul and replacement schedule and inspection programs in this chapter apply to the equipment
installed as part of this STC. The format of the inspection programs is the same as those in Beechcraft’s
maintenance manuals and maintenance manual supplements. The terminology (phase, detailed, biennial, etc.)
used in this chapter has the same meaning as Beechcraft’s terminology. Use the AMM guidelines when
following the replacement and inspection schedules specified herein. Use the Saddle Tank Inspection sheet in
this chapter to record the completion of each required inspection item at the time of the scheduled inspection
(phase 1, 2, 3, etc.). Retain this sheet with the normal aircraft maintenance records.

OVERHAUL AND REPLACEMENT SCHEDULE

The following auxiliary tank components should be replaced no later than the recommended period.

ITEM OVERHAUL OR REPLACE

Fuel drain hoses Replace every 10 years

SCHEDULED INSPECTION PROGRAM

For King Air 90 series airplanes following a scheduled inspection program in the Beechcraft Maintenance
Manual, inspect the saddle tank items during the inspection marked below.

PHASE INSP BIENNIAL INSP

ITEM (1)
1 2 3 4 INT COMP
Exterior placards X X X X X X
Fuel drains operational check X X X X X X
Fuel level indicator X X
Fuel level indicator operational check X X X X X X
Fuel level indicator placard X X X X X X
Fuel level sensors X X X
Saddle tanks X X X X X X
Saddle tank fairings X X X
Saddle tank plumbing X X

NOTES:
(1) See the Saddle Tank Inspection sheet in this chapter for inspection details.

PAGE 7
MANUAL No. 26005-30 CHAPTER 5 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 8
MANUAL No. 26005-30 CHAPTER 5 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK INSPECTION

Owner ___________________________________ Total Time __________ Total Cycles _________
W.O. No. _________________________________ Date In ____________ Date Out ____________
Serial No. ______________ Reg. No. __________ STC Installed TIS ________ Cycles _______
Inspection (1,2,3,4,INT,COMP): _______________
NOTE: Inspect only the items required by the applicable phase or other inspection as designated by an “X” in
the inspection program table. Write “N/A” if an item is not required for the applicable inspection.

A. PILOT COMPARTMENT

REFERENCE MECH INSP

1. FUEL LEVEL INDICATOR PLACARD - Check placard for proper 26005-30

adhesion, visibility, signs of damage. Ch. 11
2. FUEL LEVEL INDICATOR - Check security of attachment. Check 26005-30
connectors & wiring for damage, chafing and security. Ch. 28

B. LEFT WING

REFERENCE MECH INSP

1. EXTERIOR PLACARDS - Check placards for proper adhesion, visibility, 26005-30

signs of damage. Ch. 11
2. SADDLE TANK - Check tank exterior for loose rivets, fasteners,
damage & leaks. Check wing mounting bolts (5) for security & proper 26005-30
installation. Inspect fuel cap for damage and attachment. Inspect the Ch. 28
visible fuel cap packing for flexibility, splits, cracks, or distortion.
3. SADDLE TANK FAIRING - Remove fairing. Check for security, missing 26005-30
fasteners & damage. Ch. 28
4. SADDLE TANK PLUMBING - Check fuel and vent lines for leaks, 26005-30
security of attachment & signs of damage. Ch. 28
5. FUEL LEVEL SENSORS - With fairing removed, check saddle tank
26005-30
optical level switches (5) for damage & leaks at mounting holes.
Ch. 28
Check connectors & wiring for damage, chafing and security.

PAGE 9
MANUAL No. 26005-30 CHAPTER 5 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

C. RIGHT WING

REFERENCE MECH INSP

1. EXTERIOR PLACARDS - Check placards for proper adhesion, visibility, 26005-30

signs of damage. Ch. 11
2. SADDLE TANK - Check tank exterior for loose rivets, fasteners,
damage & leaks. Check wing mounting bolts (5) for security & proper 26005-30
installation. Inspect fuel cap for damage and attachment. Inspect the Ch. 28
visible fuel cap packing for flexibility, splits, cracks, or distortion.
3. SADDLE TANK FAIRING - Remove fairing. Check for security, missing 26005-30
fasteners & damage. Ch. 28
4. SADDLE TANK PLUMBING - With fairing removed, check fuel and vent 26005-30
lines for leaks, security of attachment & signs of damage. Ch. 28
5. FUEL LEVEL SENSORS - With fairing removed, check saddle tank
26005-30
optical level switches (5) for damage & leaks at mounting holes.
Ch. 28
Check connectors & wiring for damage, chafing and security.

D. OPERATIONAL INSPECTION

REFERENCE MECH INSP

1. FUEL LEVEL INDICATOR – Check the indicator during start and run of
the engine to verify the LEDs illuminate according to the level of fuel 26005-30
in the saddle tanks. Conduct the "System Functional Test" only if Ch. 28
necessary for troubleshooting or checking indicator function.
2. FUEL DRAINS - Check saddle tank fuel drain valves (4) for proper 26005-30
operation. Ch. 28

INSPECTION COMPLETED
I certify that this inspection was performed in accordance with the CenTex Saddle Tank Equipment Inspection
Program and that the airplane is approved for return to service:

MECHANIC: _____________________________ CREW CHIEF: __________________________________

INSPECTOR: ____________________________ DATE: ________________________________________

PAGE 10
MANUAL No. 26005-30 CHAPTER 5 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 11
PLACARDS AND MARKINGS
PLACARDS AND MARKINGS – DESCRIPTION AND OPERATION
The placards and markings added to the airplane for this STC are located in the areas indicated below.
Interior placards are in location A. Exterior placards are in locations B, C, D.

B
C
D
A

INTERIOR PLACARDS AND LIMITATION MARKINGS

Location A – Fuel Panel:
The placard on the fuel level indicator, located next to the pilot’s seat, shows the quantity for each of the five
fuel level sensors in both the left and right auxiliary fuel saddle tanks. Refer to the CTA airplane flight manual
supplement for this STC.

Placard
SADDLE TANKS
QTY (GALS)
90 90

75 75

50 50
Fuel level indicator
assembly
20 20

0 0

LH RH

PAGE 11
MANUAL No. 26005-30 CHAPTER 11 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

EXTERIOR PLACARDS AND MARKINGS

Location B – Top of Saddle Tank & Nacelle Tank Filler Access Door:

Placard

Nacelle Tank
Fuel Placard Filler Access
Door

MANUAL FOR FUEL DESIGNATIONS

FULL BEFORE FILLING SADDLE TANK

MANUAL FOR FUEL DESIGNATIONS

NACELLE & MAIN TANKS MUST BE

SEE PILOTS OPERATING

NACELLE TANK
CAPACITY: 57 U.S. GAL.

FILLER ACCESS
NACELLE TANK
SADDLE TANK FUEL
SEE PILOTS OPERATING
CAPACITY: 90 U.S. GAL.

USE JET FUEL

WITH WINGS LEVEL

USE JET FUEL

Saddle Tank
Filler

Fairing

7.3
1) Fuel Placard – located on top of each saddle tank, behind the fuel filler cap.

SADDLE TANK FUEL

USE JET FUEL
SEE PILOTS OPERATING
3.7 MANUAL FOR FUEL DESIGNATIONS
CAPACITY: 90 U.S. GAL.
WITH WINGS LEVEL
NACELLE & MAIN TANKS MUST BE
FULL BEFORE FILLING SADDLE TANK
4.5
2) Nacelle Tank Filler Access Placard – located on door on top of fairing.

1.4
NACELLE TANK
FILLER ACCESS

PAGE 12
MANUAL No. 26005-30 CHAPTER 11 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

Location C – Bottom of Saddle Tank Sump Drain:

Drain Placard
Saddle Tank
Sump Drain

Location D – Inboard Wheel Well Nacelle Drain:

Saddle
Tank

Drain Placard

FUEL DRAIN

Fuel Line Drain

Nacelle

3.5 drain and fuel line drain.

Drain Placard – located adjacent to the saddle tank sump

.7 FUEL DRAIN

PLACARDS AND MARKINGS - MAINTENANCE PRACTICES

Inspect placard for damage and wear. Replace placard if it becomes illegible or is peeling or delaminating.

PAGE 13
MANUAL No. 26005-30 CHAPTER 11 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 14
MANUAL No. 26005-30 CHAPTER 11 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 12
SERVICING
GENERAL
In addition to the servicing information and procedures specified in the Beechcraft King Air 90 Series
Maintenance Manual, follow the procedures below for equipment installed as part of this STC.

REPLENISHING
FUEL SYSTEM SERVICING
FILLING THE TANKS
Saddle Tanks
1) Fill the saddle tanks last. The saddle tank fuel caps are located on top of the tank, behind the
nacelles. Verify both nacelle and wing tanks are full before filling the saddle tanks.
2) Do not fill the saddle tank beyond its specified capacity or above the bottom of the standpipe in the
filler port.

DRAINING THE FUEL SYSTEM

Saddle Tanks
Drain the saddle tanks through the either of the two saddle tank drains or use the main fuel system drain.

LANDING GEAR SERVICING

LANDING GEAR
Shock Absorbers / Strut Servicing
Include full fuel in the saddle tanks when checking and adjusting the nose strut and main strut extension.

PAGE 15
MANUAL No. 26005-30 CHAPTER 12 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 16
MANUAL No. 26005-30 CHAPTER 12 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 24
ELECTRICAL POWER
ELECTRICAL LOAD DISTRIBUTION - MAINTENANCE PRACTICES
In addition to the information specified in the Beechcraft King Air 90 Series Maintenance Manual, the following
electrical load data applies for the equipment installed as part of this STC.

ELECTRICAL LOAD UTILIZATION CHARTS

The equipment installed as part of this STC adds the following continuous loads.

ELECTRICAL EQUIPMENT
Total
No. Load Ea. Total Load per
Equipment
Units Unit Load System
Used Amps DC Amps DC Amps DC Notes
FUEL LEVEL INDICATION SYSTEM 0.30 1
Optical level switches 10 0.008 0.08
LED indicators 10 0.020 0.20
Relay 2 0.010 0.02

Notes:
1) The fuel level indication system is added to the existing fuel gauge circuit.

PAGE 17
MANUAL No. 26005-30 CHAPTER 24 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 18
MANUAL No. 26005-30 CHAPTER 24 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

CHAPTER 28
FUEL
GENERAL
Follow the basic fuel system information and procedures specified in the Beechcraft Maintenance Manual.
Follow the procedures in this chapter for equipment installed as part of this STC.

CONTENTS
SADDLE TANK FUEL SYSTEM – DESCRIPTION AND OPERATION
SADDLE TANK FUEL SYSTEM – TROUBLESHOOTING
SADDLE TANK FUEL SYSTEM – MAINTENANCE PRACTICES
FUEL FILLER CAP INSPECTION
FAIRING REMOVAL AND INSTALLATION
FUEL SCREEN INSPECTION
FUEL SCREEN REMOVAL AND INSTALLATION
FUEL SCREEN CLEANING
CHECK VALVE INSPECTION AND REPLACEMENT
SADDLE TANK REMOVAL
SADDLE TANK INSTALLATION
SADDLE TANK LEAK TEST
SADDLE TANK LEAK REPAIR
SADDLE TANK MATERIALS
SADDLE TANK FUEL INDICATING SYSTEM – DESCRIPTION AND OPERATION
SADDLE TANK FUEL INDICATING SYSTEM – TROUBLESHOOTING
SADDLE TANK FUEL INDICATING SYSTEM – MAINTENANCE PRACTICES
FUEL LEVEL INDICATING SYSTEM FUNCTIONAL TEST
FUEL LEVEL INDICATOR REMOVAL AND INSTALLATION
OPTICAL LEVEL SWITCH REMOVAL – FRONT BULKHEAD (3 PLCS)
OPTICAL LEVEL SWITCH REMOVAL – AFT BULKHEAD (2 PLCS)
OPTICAL LEVEL SWITCH INSTALLATION

PAGE 19
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK FUEL SYSTEM – DESCRIPTION AND OPERATION

The Saddle Tank STC adds a pair of all-aluminum, external fuel tanks connected directly to flow through an
integral strainer into each wing fuel tank by gravity. Refer to the fuel system diagram in Figure 1 on page 2.
The functions of the airplane’s wing and nacelle fuel systems are unchanged by the addition of the saddle tanks.
The saddle fuel tanks are mounted behind each engine nacelle to the upper surface of the wing. Five ¼-inch
(AN4) bolts hold each tank to the wing. Also, sixteen screws attach the front of the tank to the engine nacelle
structure.
Each tank has its own filler opening located on top of the saddle tank and a sump drain at the lower, aft end of
the saddle tank. The main fuel line from the saddle tank goes through the back of the wheel well and enters at
the airplane fuel system through a modified line located between the main interconnect line and the nacelle
tank as shown in Figure 1a on page 2. There is a low-point drain for the saddle tank fuel line at the aft, inboard
side of the nacelle fairing. There is also a check valve in the saddle tank fuel line to prevent fuel migratrating
from the wing tank into the saddle tank.
Ventilation for the saddle tank is provided by the airplane’s existing vent system. The existing vent line, running
from the center section wing tank to the outer wing and nacelle tanks, is modified and routed up, through the
wing and into the saddle tank as shown in Figure 1a on page 2.

SADDLE TANK FUEL SYSTEM – TROUBLESHOOTING

If the saddle tank auxiliary fuel system is not working properly, consult Chart 1 below for possible problem
indicators, causes and solutions. Use this chart in conjunction with the procedures in Fuel - Maintenance
Practices.

Chart 1. Troubleshooting Fuel System

Indication Possible Cause Remarks
1) Fuel from saddle tank not a) Tank outlet screen assembly a) Follow procedure to inspect
transferring to center wing (finger screen) is blocked. and clean or replace screen
tanks. assembly.

b) Check valve not opening. b) Clean, repair, or replace check

valve.
2) Fuel from saddle tank slow a) See possible causes above. a) See remarks above.
or hesitant in transferring
to center wing tanks. b) Blockage in ventilation system. b) Inspect vent lines and vent
openings for blockage.

PAGE 20
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK FUEL SYSTEM - MAINTENANCE PRACTICES

The saddle tanks may need to be checked for dirt or debris to prevent restrictions to the fuel flow. If noticeable
amount of debris is found at the outlet screen in the fuel tank, it is advisable to also inspect the check valve
inside wheel well. To check the fuel screen, follow the steps below.

FUEL FILLER CAP INSPECTION

Visually inspect the fuel filler cap. Open the cap. Verify the cotter pin and lanyard are secure. Check all
visible packings to make sure they are in good condition. Check the outer packing for flexibility, splits, cracks
or distortion. If the packing is damaged, replace the fuel filler cap.

FAIRING REMOVAL AND INSTALLATION

In order to access the front of the saddle fuel tank or to remove the tank, remove the fairing between the
engine nacelle and saddle tank as follows.
a. Remove existing access panels on the inboard and outboard sides of the nacelle.
b. Remove #8 screws, washers & nuts securing the fairing to the nacelle (20 each).
c. Remove the remaining screws securing the fairing to the top of the nacelle firewall, nacelle, fairing
support brackets, and saddle tank.
d. Carefully pull the fairing off so as to avoid scratching the wing or nacelle.
e. Check the fairing for condition. Repair dents or damage to sheet metal per Beechcraft AMM.
f. To install fairing, place it back on the saddle tank and nacelle.
g. Fasten the fairing to the saddle tank, support brackets, and nacelle using the original hardware.
h. Reinstall the access panels removed from the nacelle.

FUEL SCREEN INSPECTION

a. Lower wing flaps (full down).
b. Disconnect all electrical power from the airplane.
c. Make sure existing wing tank is empty or below 1/8 capacity.
d. Drain all fuel from the saddle tank.
e. Remove the screws holding the lower, aft close-out panel on the bottom of the tank in order to get to
the aft tank access panel. Remove the close-out panel.
f. On the aft tank access panel, disconnect the optical level switch harness at the 3-pin connector.
g. Remove 20 ea. AN3 bolts, washers, and lock washers or safety wire securing the access panel.
Remove the access panel and seal.
h. Check the fuel screen at the aft, inboard corner of the tank for damage and blockage. Remove any
debris.
i. To remove or replace the screen assembly, follow the removal and installation procedures below.
j. Inspect the interior of the tank and remove any debris.
k. Inspect the access panel seal for damage. Replace as necessary.

PAGE 21
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

l. Reinstall the access panel and seal with 20 ea. AN3 bolts, washers, and lock washers; or secure with
safety wire.
m. Reconnect the optical level switch harness at the 3-pin connector. Make sure the wire harness is in
good condition and secure.
n. Reinstall the close-out panel on the tank using the original screws.

FUEL SCREEN REMOVAL AND INSTALLATION

a. Should the fuel screen need to be removed for further inspection or to be replaced, follow instructions
under SADDLE TANK REMOVAL to first remove the saddle tank from the wing. The fuel screen is
replaced from the bottom of the tank.
b. Unscrew the fuel screen assembly from the bottom of the tank.
c. Check the screen for damage and blockage.
d. Clean the screen per the FUEL SCREEN CLEANING procedure below.
e. Apply EZ TURN lubricant (see materials chart) to the pipe threads on fuel screen adapter and screw
it back into the tank outlet fitting.
f. Perform a leak test per the SADDLE TANK LEAK TEST procedure on page 24. Tighten or seal the
screen assembly as necessary.
g. Reinstall the saddle tank per the SADDLE TANK INSTALLATION procedure on page 23.

FUEL SCREEN CLEANING

a. Clean screen with mild detergent and a stainless steel wire brush.
b. Remove dirt and sediment build-up.
c. Rinse with clean water.
d. Check screen for cracks in solder joints. Replace damaged screen assembly.

CHECK VALVE INSPECTION AND REPLACEMENT

This procedure applies to the check valve installed in the saddle tank supply line.
a. Disconnect all electrical power from the airplane.
b. Make sure the wing tank is empty
c. Drain all fuel from the saddle tank.
d. Drain fuel from the drain valve located in the aft inboard side of the wheel well.
e. Remove the check valve from the fuel line and check for dirt or debris. Flush clean as necessary.
f. Verify the swing valve operates freely by tilting the check valve down and up. Replace the check
valve if it is damaged or does not function properly.
NOTE: The swing valve used in this check valve does not have a spring.
g. Reinstall the check valve. Make sure the check valve is oriented horizontally with the “HINGE” label
up (on top). Make sure the check valve arrow points inboard.

PAGE 22
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK REMOVAL

a. Lower flaps (full down).
b. Disconnect all electrical power from airplane.
c. Make sure existing wing tank is empty or below 1/8 capacity.
d. Drain all fuel from saddle tank through sump drain.
e. Drain fuel from drain valve located in the aft inboard side of the wheel well.
f. Remove fairing per the FAIRING REMOVAL AND INSTALLATION procedure on page 21.
g. Disconnect bonding straps from fairing brackets.
h. Disconnect fuel sensor wire harness at the six pin connector.
i. Disconnect vent lines (accessed through the wheel well)
j. Disconnect fuel supply line (accessed behind the aft spar).
k. Remove #8 screws securing the front of the tank to the aft nacelle structure.
l. Remove five (5) AN4 bolts attaching the tank to the upper wing. Three (3) bolts are located mid wing
and two (2) are located behind the aft spar.
m. Lift tank up and off the wing.
n. Protect vent and fuel fittings with caps and plugs.

SADDLE TANK INSTALLATION

a. If needed, install alignment pins in two aft mounting holes. Fabricate pins from AN4 bolts like the
one shown in Figure 2 on page 24.
b. Remove protective caps and plug from vent and fuel fittings.
c. Carefully lower saddle tank onto wing, making sure the two alignment pins are inserted into the bolt
holes on the wing without excessive force. When aligned properly, the weight of the tank should be
sufficient to insert the pins into the bolt holes.
d. Use an awl if necessary to align the mounting holes in the forward mounting bracket with the holes in
the aft nacelle structure. Install with #8 screws & nuts (16 each minimum).
e. Secure tank to wing with three (3) AN4H bolts at the mid wing location. Remove the alignment pins
at the aft spar location with a flat head screw driver. Install two (2) AN4 bolts and lock tabs at this
location. Torque all bolts 50 to 70 inch-pounds. Secure with safety wire. Aft two (2) bolts are secured
with the lock tab.
f. Apply EZ TURN lubricant (see materials chart) to tank fuel outlet fitting threads. Secure fuel line to
tank.
g. Apply EZ TURN lubricant (see materials chart) to tank vent fitting threads. Secure two (2) vent lines
to tank.
h. Reconnect the fuel sensor wire harness at the six pin connector. Secure connectors with wire tie(s).
i. Reconnect bonding straps to fairing brackets (2 places per tank).
j. Reinstall fairing per the FAIRING REMOVAL AND INSTALLATION procedure on page 21.

PAGE 23
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

TAPER & 1.5

ROUND OFF END

Ø.25
.05 X .2
SLOT
CUT OFF
BOLT HEAD

Figure 2. Alignment Pin

(not to scale)

SADDLE TANK LEAK TEST

a. Make sure all openings are sealed or capped off.
b. Fill tank with fuel and check for leaks.
c. Fuel tank may also be leak tested with shop air.
1. Verify tank openings are sealed or capped off except one open fitting.
2. Insert a rubber hose into fitting and seal around hose.
3. Use a regulator to pressurize tank to 1 - 2 psig (use shop air or similar).

CAUTION: Do not exceed 5 psig air pressure inside the tank.

4. Spray mild soapy water solution along seams, rivet heads, and around any recently replaced
components and check for bubbles.
NOTE: Air leaks at the fuel cap are normal.
5. Remove pressure source and allow tank to depressurize.

**WARNING**
Opening the fuel cap or another fitting with the tank pressurized
could result in serious injury.

d. Repair and or reseal any leaks found. Retest as needed.

SADDLE TANK LEAK REPAIR

For leak checks and repairs to the auxiliary fuel saddle tank, follow the procedures in the section on wet wing
fuel cell repairs in Chapter 28 of the Beechcraft AMM. If the leak cannot be repaired using the specified
procedures, contact CenTex Aerospace for further instructions.
NOTE: For repairing a leak in the saddle tank, any of the sealants and solvent materials recommended for
wet wing fuel cell repairs in the Beechcraft AMM may be used. However, CenTex recommends using PR-
1422 Class A or Class B sealant per CTA Process Specification 26005-8002 to seal the tank interior. See
Saddle Tank Materials on the next page for information.

PAGE 24
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK MATERIALS

ITEM MATERIAL PRODUCT SUPPLIER
1 Thread lubricant EZ TURN Lubricant United Erie
(a.k.a. “fuel lube”; meets 1432 Chestnut St
AMS-G-6032) Erie, PA 16502
www.unitederie.com
2 Sealant PR-1422 Class A PPG Aerospace (PRC-
(meets AMS-S-8802) Desoto)
12780 San Fernando Rd
PR-1422 Class B
Sylmar, CA 91342
(meets AMS-S-8802)
www.ppgaerospace.com
PR-1428 Class B
(meets AMS 3284)

PAGE 25
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

SADDLE TANK FUEL INDICATING SYSTEM – DESCRIPTION AND OPERATION

The saddle tank fuel level indication system consists of five optical level switches installed in each fuel tank
connected to a fuel level indicator panel mounted aft of the fuel management panel on the pilot’s side wall. The
optical switches use infra-red light to determine whether the sensor is submerged in fuel or exposed to air. The
fuel level indicator has a left and right column of green LEDs that are labeled by the quantity of fuel
corresponding to the level of the switch in the tank. Refer to the FUEL LEVEL INDICATING SYSTEM
FUNCTIONAL TEST section below for the fuel level markings according to each size of saddle tank. When
fuel is at or above the indicated level, the LED illuminates green. As fuel drops below each level sensor, the
LED extinguishes with the exception of the last LED. The bottom LED is a bi-color LED that stays green when
the switch is submerged in fuel then changes to amber when the tank is empty.

SADDLE TANK FUEL INDICATING SYSTEM – TROUBLESHOOTING

If the fuel level indicator is not working properly, consult Chart 2 below for possible problem indicators, causes
and solutions

Chart 2. Troubleshooting Fuel Level Indicating System

Indication Possible Cause Remarks
1) Fuel level indicator LEDs a) Aircraft power is OFF. a) Turn on main battery power.
not illuminated.
b) Existing fuel indicator circuit b) Depress circuit breaker.
breaker is OFF.

c) Blown fuse in fuel level c) Replace fuse or repair indicator

indicator assembly. assembly.

2) Individual LED(s) not a) Fuel level in tank is below fuel a) Condition is normal.
illuminated. level switch.

b) Faulty LED. b) Replace indicator assembly.

c) Faulty fuel level switch c) Replace sensor.

(sensor).

3) “0” quantity LED is amber Faulty fuel level switch (sensor). Replace sensor.
with fuel in saddle tank.

SADDLE TANK FUEL INDICATING SYSTEM - MAINTENANCE PRACTICES

FUEL LEVEL INDICATING SYSTEM FUNCTIONAL TEST
Since the fuel level indicator and optical switches are activated every time the ship’s power is turned on, a
functional test is made every time the fuel tank is filled. To determine if the switches are functioning properly,
observe the fuel level indicator when the tank is empty or is being filled. Figure 3 on the next page shows
the LEDs illuminated at different fuel levels.

PAGE 26
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

When a fuel tank is empty, only the bottom or “0” gallon LED is illuminated. The LED is amber in color. As
the fuel tank is filled, the “0” gallon LED changes from amber to green. Each next higher LED will illuminate
green as the fuel level submerges the corresponding level switch. If any LED remains off when the fuel level
is above the corresponding switch sensor, there is a malfunctioning switch or LED. For the “0” gallon LED, if
the color does not change from green to amber when the fuel tank is empty, the switch is faulty.

Indicator Fuel Tank Quantity (gallons)

LED 90 75 50 20 0
90 ON
75 ON ON
50 ON ON ON
20 ON ON ON ON
0 ON ON ON ON ON

Figure 3. Fuel Level Indication

NOTE: Before performing the functional test, fill the wing and nacelle tank.
NOTE: When performing the functional test, the fuel quantity required to illuminate the indicator LED depends
on the orientation of the airplane. To check the accuracy of the fuel level indication, the functional test must
be done with the airplane level. See Beechcraft AMM for procedures to level the airplane.

FUEL LEVEL INDICATOR REMOVAL AND INSTALLATION

To replace the fuel level indicator, follow the procedure below.
a. Disconnect all electrical power from the airplane.
b. Remove the pilot’s side panel per Beechcraft AMM procedures sufficiently to access the area behind
the fuel level indicator.
c. Remove the screws attaching the fuel level indicator to the bracket.
d. Disconnect the fuel level indicator wire harness.
e. Install the fuel level indicator in the reverse order.
f. Turn on aircraft power to verify the fuel level indicator illuminates. Perform the functional test as
needed.

OPTICAL LEVEL SWITCH REMOVAL - FRONT BULKHEAD (3 PLCS)

These switches are mounted in the forward bulkhead of the tank as shown in Figure 4 on page 30.
a. Disconnect all electrical power from the airplane.
b. Make sure existing wing tank is empty or below 1/8 capacity.
c. Drain all fuel from the saddle tank.
d. Remove fairing per the FAIRING REMOVAL AND INSTALLATION procedure on page 21.
e. Disconnect the optical level switch harness at the 3-pin connector.
f. Remove the fuel filler cap.

PAGE 27
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

g. Remove the filler neck adapter assembly. Remove the 12 screws and carefully separate the filler
neck adapter, which is sealed with PRC, from the tank.
h. Through the filler hole, loosen the 12mm hex nut from the switch.
i. Carefully loosen and remove the switch. The switch is sealed with PRC.

OPTICAL LEVEL SWITCH REMOVAL - AFT BULKHEAD (2 PLCS)

These switches are mounted in the aft bulkhead of the tank as shown in Figure 4 on page 30.
a. Lower wing flaps (full down).
b. Disconnect all electrical power from the airplane.
c. Make sure existing wing tank is empty or below 1/8 capacity.
d. Drain all fuel from the saddle tank.
e. Remove the screws holding the lower, aft close-out panel on the bottom of the tank in order to get to
the aft end of the tank. Remove the close-out panel.
f. On the aft tank access panel, disconnect the optical level switch at the 3-pin connector.
g. Remove 20 ea. AN3 bolts, washers, and lock washers or safety wire securing the access panel.
Remove the access panel and seal.
h. Disconnect the upper optical level switch harness at the 3-pin connector (if necessary).
i. Loosen the 12mm hex nut from the switch.
j. Carefully loosen and remove the switch. The switch is sealed with PRC.

OPTICAL LEVEL SWITCH INSTALLATION

See Figure 5 on page 31 for installation details.
a. Before installing the optical level switch, remove any old PRC sealant from the mounting hole and
clean surface with acetone and a clean cloth.
b. Apply a thin coat of PRC PR-1428 Class B sealant (see Saddle Tank Materials on page 25) to the
mounting face of the switch and the external surface surrounding the mounting hole. Be careful not
to get sealant on the glass cone of the switch. Should sealant contact the glass cone, wipe off sealant
with clean cloth dipped in acetone.
NOTE: Apply sealant per CTA Process Specification 26005-8002.
c. Insert the switch into the mounting hole with the seal between the switch and the tank surface.
d. Secure the switch in the hole with the washer and 12 mm hex nut. Tighten the nut ½ turn beyond
hand tight.
CAUTION: Do not over-tighten nut. Do not scratch glass cone.
e. Inspect tank interior and remove any debris before installing access panels or filler neck adapter.
f. If removed, install the filler neck adapter and fuel cap as follows:
1. Remove old PRC from the mating surfaces and clean surfaces with acetone and clean cloth.
2. Apply PR-1428 Class B sealant (see Saddle Tank Materials on page 25) to the adapter
flange per CTA Process Specification 26005-8002.
3. Install the adapter inside the tank using the original twelve (12) #10 countersunk screws.

PAGE 28
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

4. Install the fuel cap.

g. If removed, install the aft tank access panel as follows:
1. Inspect the access panel seal for damage or brittleness. Replace as necessary.
2. Reinstall the access panel and seal with 20 ea. AN3 bolts, washers, and lock washers; or
secure with safety wire.
h. Perform a leak test per the SADDLE TANK LEAK TEST procedure on page 24.
i. Reconnect the optical level switch harness at the 3-pin connector. Make sure the wire harness is in
good condition and secure.
j. Check the indicating system per the FUEL LEVEL INDICATING SYSTEM FUNCTIONAL TEST
procedure on page 26.
k. If removed, reinstall the close-out panel on the tank using the original screws.
l. If removed reinstall fairing per the FAIRING REMOVAL AND INSTALLATION procedure on page 21.

PAGE 29
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

FRONT
BULKHEAD
SWITCH #1

SWITCH #2

SWITCH #3

NACELLE

SWITCH #4

SWITCH #5

Figure 4. Saddle Tank Optical Level Switch Locations

PAGE 30
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

Figure 5. Optical Level Switch Installation

PAGE 31
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE 32
MANUAL No. 26005-30 CHAPTER 28 Rev. 2, Jan. 2021
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

APPENDIX A

BEECHCRAFT KING AIR 90 SERIES

AUXILIARY FUEL TANKS

ILLUSTRATED PARTS CATALOG

PAGE A1
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A2
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

SCOPE
This section provides an illustrated list of the equipment installed under STC SA11142SC for 65-A90-1 & 65-
A90-4 series aircraft. The information contained herein should be used as reference only to help with ordering
replacement parts when necessary. The STC drawings contain the FAA approved data and may supersede
the information in the parts lists until this section is updated to reflect the latest drawings.

FORMAT
This Illustrated Parts Catalog (IPC) is broken down into systems, installations, assemblies & detail parts. The
example below shows the basic format. The following terms used in the parts lists are defined below.
ITEM – the item number in the parts list corresponds to the item number in the illustration.
PART NUMBER – lists the part number of the item. The number can be a CTA part number, a vendor
number, or a mil-spec number.
NOMENCLATURE – name of the part and if it is a detail part, an assembly or installation.
EFFECTIVITY – if listed, the serial numbers of the aircraft eligible for the specific part installation. If the parts
are eligible for installation on all serial number King Air 90s, the column is left blank.
UNITS/ASSY – quantity of the parts used in each system installation per aircraft.

EXAMPLE
The example shows how parts are illustrated and listed by installation, assembly, etc.

1 2 3 4 5

6 7 8 9 10

11 12 13

14

B
NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
B
26005-4000-1 INSTALLATION, FUEL SYSTEM, LH 1
26005-4000-2 INSTALLATION, FUEL SYSTEM, RH 15 16
1
1 26005-4002-3 . TUBE ASSEMBLY 1
17
21 20 19 ATTACHING PARTS

2 AN832-12D A-A
. . BULKHEAD UNION 18
1
3 AN960-1716 . . WASHER 1
4 AN924-12D . . NUT 1

PAGE A3
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A4
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-2000
FUEL TANKS

PAGE A5
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A6
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

4 5

14
B 3

26005-2000-1/-2 FUEL TANKS, SHEET 1 OF 2

PAGE A7
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

10

W.S. 85.5

6
W.S. 68.0

REAR SPAR
(NAC. STA. 160.0)
7

11
8

12
9 11

B 13

26005-2000-1/-2 FUEL TANKS, SHEET 2 OF 2

PAGE A8
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
26005-2000-1 INSTALLATION, FUEL TANK,LH 1
26005-2000-2 INSTALLATION, FUEL TANK, RH 1
1 26005-2001-1 . FUEL TANK ASSEMBLY, LH 1
26005-2001-2 . FUEL TANK ASSEMBLY, RH 1
ATTACHING PARTS
2 26005-2008-8 . . SHIM 1
AN526-632R6 . . .SCREW 2
AN960-6 . . .WASHER 2
AN365-632 . . .NUT 2
3 26005-2011-13 . . CHAFING STRIP 1
4 AN525-832R8 . . SCREW 16
AN960-8 . . WASHER (OPTIONAL) 16
5 AN365-832 . . NUT 16
130007 . . CLIP NUT (ALTERNATE) A/R
-------*-------
6 26005-2011-11 . CHAFING STRIP 1
7 AN970-4 . WASHER 2
8 26005- . LOCK TAB 1
9 AN4H-10A . BOLT 2
10 26005-2011-12 . CHAFING STRIP 4
11 AN970-4 . WASHER 3
12 AN4H-10A . BOLT 1
13 AN4H-12A . BOLT 2
14 WR-8988 . SEAL A/R

PAGE A9
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A10
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-3000
FUEL TANK FAIRING

PAGE A11
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A12
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

D A

2
4

26005-3000-1/-2 FUEL TANK FAIRING, SHEET 1 OF 4

PAGE A13
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

10

8 9

26005-3000-1/-2 FUEL TANK FAIRING, SHEET 2 OF 4

PAGE A14
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

12

11

16

12

12
14

C 12

26005-3000-1/-2 FUEL TANK FAIRING, SHEET 3 OF 4

PAGE A15
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

18

17

18

18 19

26005-3000-1/-2 FUEL TANK FAIRING, SHEET 4 OF 4

PAGE A16
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
26005-3000-1 INSTALLATION, FUEL TANK FAIRING, LH 1
26005-3000-2 INSTALLATION, FUEL TANK FAIRING, RH 1
1 26005-3005-1 . FAIRING, LH 1
ATTACHING PARTS
2 AN525-832R8 . . SCREW 53
AN960-8 . . WASHER 11
3 MS21044N08 . . NUT 11
-------*-------
4 26005-3002-1 . BRACKET ASSEMBLY, LH INB’D 1
ATTACHING PARTS
MS27039-1-08 . . SCREW 3
MS27039-08-08 . . SCREW 1
-------*-------
5 26005-3004-2 . ACCESS DOOR 1
6 26005-3002-2 . BRACKET ASSEMBLY, LH OUTB’D 1
ATTACHING PARTS
MS27039-1-08 . . SCREW 5
MS27039-08-08 . . SCREW 1
-------*-------
7 26005-3003-1 . LENS 1
ATTACHING PARTS
AN526-632R6 . . SCREW 4
MS21044N06 . . NUT 4
-------*-------
8 AN525-832R8 . SCREW 21
9 MS21044N08 . NUT 9
AN960-8 . WASHER 9
10 AN525-10R8 . SCREW 1
11 26005-3005-2 . FAIRING, RH 1
ATTACHING PARTS
12 AN525-832R8 . . SCREW 51
AN960-8 . . WASHER 10
13 MS21044N08 . . NUT 10
-------*-------
14 26005-3002-4 . BRACKET ASSEMBLY, RH OUTB’D 1
ATTACHING PARTS
MS27039-1-08 . . SCREW 5
MS27039-08-08 . . SCREW 1
-------*-------

PAGE A17
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
15 26005-3003-1 . LENS 1
ATTACHING PARTS
AN526-632R6 . . SCREW 4
MS21044N06 . . NUT 4
-------*-------
16 26005-3004-2 . ACCESS DOOR 1
17 26005-3002-3 . BRACKET ASSEMBLY, RH INB’D 1
ATTACHING PARTS
MS27039-1-08 . . SCREW 3
MS27039-08-08 . . SCREW 1
-------*-------
18 AN525-832R8 . SCREW 23
AN960-8 . WASHER 12
19 MS21044N08 . NUT 12

PAGE A18
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-4000
FUEL SYSTEM

PAGE A19
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A20
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

A
FILLER ACCESS
NACELLE TANK

26005-4000-1/-2 FUEL SYSTEM, SHEET 1 OF 3

PAGE A21
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

1 2 3 4 5

6 7 8 9 10

11 12 13

14

15 16

17
21 20 19

A-A 18

26005-4000-1/-2 FUEL SYSTEM, SHEET 2 OF 3

PAGE A22
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

39 38
FUEL TO
AUX. TANK

E
NG
HI

23

24

28 27 26 25 FUEL FROM
WING TANK 22
FWD INB'D
32 31 30 29 40
OUTB'D B-B

33 36 37

34 35

C-C D-D

26005-4000-1/-2 FUEL SYSTEM, SHEET 3 OF 3

PAGE A23
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A24
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
26005-4000-1 INSTALLATION, FUEL SYSTEM, LH 1
26005-4000-2 INSTALLATION, FUEL SYSTEM, RH 1
1 26005-4002-3 . TUBE ASSEMBLY 1
ATTACHING PARTS
2 AN832-12D . . BULKHEAD UNION 1
3 AN960-1716 . . WASHER 1
4 MS92513-119 . . O-RING 1
5 AN924-12D . . NUT 1
-------*-------
6 26005-4002-4 . TUBE ASSEMBLY 1
ATTACHING PARTS
7 AN832-12D . . BULKHEAD UNION 1
8 AN960-1716 . . WASHER 1
9 MS92513-119 . . O-RING 1
10 AN924-12D . . NUT 1
-------*-------
11 26005-4003-1 . TUBE ASSEMBLY 2
ATTACHING PARTS
12 2231-12 . . HOSE 2
13 200-16H . . CLAMP 4
-------*-------
14 26005-4005-1 . SCREEN ASSEMBLY 1
15 26005-4008-1 . TUBE ASSEMBLY 1
16 AN821-10D . ELBOW 1
17 26005-4007-1 . TUBE ASSEMBLY 1
18 130001-4S-0152 . HOSE ASSEMBLY 1
19 26005-4001-1 . FITTING ASSEMBLY, LH 1
26005-4001-2 . FITTING ASSEMBLY, RH 1
ATTACHING PARTS
20 AN960-816L . . WASHER 1
21 AN924-10D . . NUT 1
-------*-------
22 26005-4010-1 . TUBE ASSEMBLY 1
23 26005-4006-1 . TUBE ASSEMBLY, LH 1
26005-4006-2 . TUBE ASSEMBLY, RH 1
24 26005-4012-1 . CHECK VALVE 1
25 AN724D10 . CLAMP 1
26 MS25083-1BB6 . JUMPER ASSEMBLY 1
27 MS27039-1-09 . SCREW 2
28 AN363-1032 . NUT 2

PAGE A25
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY
29 MS21919DG10 . CLAMP 1
30 MS21919DG44 . CLAMP 1
31 MS27039-1-09 . SCREW 1
32 AN363-1032 . NUT 1
33 26005-4004-4 . BRACKET 1
ATTACHING PARTS
MS27039-1-09 . . SCREW (EXISTING) 2
AN363-1032 . . NUT (EXISTING) 2
-------*-------
34 26005-4004-1 . ACCESS PANEL ASSEMBLY 1
ATTACHING PARTS
35 MS24693S50 . . SCREW 12
-------*-------
36 CAV-110 . FUEL DRAIN VALVE 1
37 MS20823-4D . ELBOW 1
-------*-------
38 26005-4015-1 . CHECK VALVE A 1
39 26005-4016-1 . TUBE ASSEMBLY, INB'D. A 1
40 26005-4016-2 . TUBE ASSEMBLY, OUTB'D. A 1

EFFECTIVITY CODE:
A: 65-A90, B90, C90, C90A, C90GT, C90GTi

PAGE A26
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-6000
FUEL LEVEL INDICATION

PAGE A27
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A28
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

C
B
A
B

FUEL PANEL

2
1

26005-6000-1 FUEL LEVEL INDICATION

PAGE A29
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-6000-1 FUEL LEVEL INDICATION

PAGE A30
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY

26005-6000-1 INSTALLATION, FUEL LEVEL INDICATION 1

1 26005-6004-1 . ANGLE ASSEMBLY 1

ATTACHING PARTS
MS24639S27 . . SCREW (EXISTING) 1
AN526-632R6 . . SCREW (EXISTING) 1
-------*-------
2 26005-6001-1 . ASSEMBLY 1
ATTACHING PARTS
3 AN526-632R6 . . SCREW 2
-------*-------
4 OPT4922-1 . OPTICAL LEVEL SWITCH, NO 6
LLT210D324-003 . OPTICAL LEVEL SWITCH, NO (ALT.) 6
LLPK1 . NUT & SEAL WASHER (ALT.) 6
AN960-816L . WASHER 6
5 OPT4922-1 . OPTICAL LEVEL SWITCH, NO 2
LLT210D324-003 . OPTICAL LEVEL SWITCH, NO (ALT.) 2
LLPK1 . NUT & SEAL WASHER (ALT.) 2
AN960-816L . WASHER 2
6 OPT4922-2 . OPTICAL LEVEL SWITCH, NC 2
LLT210D3L24-003 . OPTICAL LEVEL SWITCH, NC (ALT.) 2
LLPK1 . NUT & SEAL WASHER (ALT.) 2
AN960-816L . WASHER 2

PAGE A31
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A32
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

26005-7000
PLACARDS

PAGE A33
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A34
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

B SADDLE TANKS

90
QTY (GALS)
90

75 75

50 50

20 20

0 0

RH LH

2
FULL BEFORE FILLING SADDLE TANK

MANUAL FOR FUEL DESIGNATIONS

NACELLE & MAIN TANKS MUST BE

FILLER ACCESS
NACELLE TANK
SADDLE TANK FUEL
SEE PILOTS OPERATING
CAPACITY: 90 U.S. GAL.
WITH WINGS LEVEL

USE JET FUEL

C C

26005-7000-1 PLACARDS, SHEET 1 OF 2

PAGE A35
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

D
FUEL DRAIN

VIEW C-C

26005-7000-1 PLACARDS, SHEET 2 OF 2

PAGE A36
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

ILLUSTRATED PARTS CATALOG

NOMENCLATURE UNITS/
ITEM PART NUMBER EFFECTIVITY
123 ASSY

26005-7000-1 INSTALLATION, PLACARDS 1

1 26005-7001-1 . PLACARD, “SADDLE TANK FUEL …” 2

2 26005-7001-2 . PLACARD, “NACELLE TANK FILLER …” 2
3 26005-7001-3 . PLACARD, “SADDLE TANKS QTY …” 1
4 26005-7001-4 . PLACARD, “FUEL DRAIN” 2

PAGE A37
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE A38
MANUAL No. 26005-30 APPENDIX A Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

APPENDIX B

BEECHCRAFT KING AIR 90 SERIES

AUXILIARY FUEL TANKS

WIRING DIAGRAM MANUAL

PAGE B1
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE B2
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

SCOPE
This section provides wiring diagrams and lists of electrical components for the equipment installed under
STC SA11142SC for Beechcraft King
EXIST. Air 90 series aircraft. The information contained herein should be used
FUEL
as reference only to help withINDICATION
ordering
(REF)
replacement parts when necessary. The STC drawings contain the

28 VDC
FAA approved data and may supersede the information in this section until it can be updated to reflect the
5A
latest drawings. RING
13
TERMINAL

PILOT'S SIDE PANEL

FORMAT
The Wiring Diagram Manual is broken down into systems & components. The example below shows the basic
format. The following terms used in the parts lists are defined below.
1 CT E102A22
0.5A
ITEM – the item number in the parts list corresponds
2 to the item number in the diagram.
PART NUMBER – lists the part number of the item. The number can be a CTA part number, a vendor
number, or a mil-spec number.
NOMENCLATURE – name of the part.
CT E101A22
EFFECTIVITY – if listed, the serial numbers of the aircraft eligible for the specific part installation. If the parts
9 SOCKET are eligible for installation on all serial number airplanes, the column is left blank.
GRN GRN
8 CONNECTOR
UNITS/ASSY – quantity of the partsCT
used in each system installation per aircraft.
E103C22 CT E104C22
1 CT E101B22 1 1
2 CT E103B22 2 GRN GRN 2
3 CT E105B22 3 CT E105C22 CT E106C22 3
EXAMPLE
4 CT E107B22 4 4
5 CTThe example shows
E109C22 5 a basic wiring diagram and list of components.
GRN The wiring GRN
diagram uses conventional 5
6 CTformats 6 for various electrical
E111C22 and symbols CT E107C22
components, ground points, etc. CT E108C22 6
11 PIN PIN 11
Each
10 CONNECTOR wire has a10wire
CONNECTOR code number. Each wire is physically
GRNlabeled with this code.
GRN
CT E109D22 CT E110D22
Items and wire traces shown with dashed lines are existing items on the airplane.
GRN 9 9 GRN
8 8
7 7

RING TERMINAL 12 YEL 2 2 YEL

3 3
4 4

1(+) 1(+)

10(-) 10(-)

CT E111D22 CT E112D22

1 26005-6001-1 ASSY

UNITS/
ITEM PART NUMBER NOMENCLATURE EFFECTIVITY
ASSY
1 26005-6001-1 ASSEMBLY 1
2 OPT4299-1 OPTICAL SWITCH, NO 8

PAGE B3
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

CONNECTION TO AIRPLANE ELECTRICAL SYSTEMS
Where connections to existing airplane electrical systems are noted, refer to the Beechcraft King Air 90 Series
Wiring Diagram Manual by airplane serial number in order to see the applicable wiring diagrams for existing
equipment.

WIRE TYPE
Use 22-gauge M227759/16 wire for repairing or replacing worn or damaged wire.

WIRE & ELECTRICAL COMPONENT REPLACEMENT

For inspection, repair, or replacement of wire and electrical components, follow the accepted procedures and
practices specified in FAA Advisory Circular AC 43.13-1B/2B for aircraft electrical systems.
Be sure to label any replacement wire with the correct wire number shown on the wiring diagram.

PAGE B4
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

26005-5001
FUEL LEVEL INDICATION

PAGE B5
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE B6
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

EXIST. FUEL
INDICATION
(REF)

28 VDC
5A
RING
13
TERMINAL

LH AUX. TANK PILOT'S SIDE PANEL

1 CT E102A22
0.5A
2

SOCKET (5 EA) 5 7 PIN (5 EA)

CONNECTOR (15 EA) 4 6 CONNECTOR (15 EA)
2 RED
1 CT E101A22
SWITCH GREEN
2
"FULL" BLUE
3
9 SOCKET
GRN GRN
CT E101D22 CT E101C22 8 CONNECTOR CT E103C22 CT E104C22
CT E101G22 1 CT E101B22 1 1
2 RED
1 CT E103A22 2 CT E103B22 2 GRN GRN 2
SWITCH GREEN
2 CT E105A22 3 CT E105B22 3 CT E105C22 CT E106C22 3
"3/4" BLUE
3 CT E107A22 4 CT E107B22 4 4
CT E109B22 5 CT E109C22 5 GRN GRN 5
CT E111B22 6 CT E111C22 6 CT E107C22 CT E108C22 6
CT E101E22
11 PIN PIN 11
2 RED
1 10 CONNECTOR CONNECTOR 10 GRN GRN
SWITCH GREEN
2 CT E109D22 CT E110D22
"1/2" BLUE
3
RING GRN 9 9 GRN
12 8 8
TERMINAL 7 7

RING TERMINAL 12 YEL 2 2 YEL

2 RED 3 3
1 CT E101H22 1 4 4

SWITCH GREEN
2 CT E109A22 2 1(+) 1(+)
"1/4" BLUE
3 RING 10(-) 10(-)
12
TERMINAL

CT E101J22
CT E111D22 CT E112D22

3 RED
1
SWITCH GREEN
2 CT E111A22 3
"EMPTY" BLUE
3 SOCKET 5 7 PIN 1 26005-6001-1 ASSY
RING CONNECTOR 4 6 CONNECTOR
12
TERMINAL

26005-5001-1 FUEL LEVEL INDICATION, LH

PAGE B7
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE B8
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

EXIST. FUEL
INDICATION
(REF)

28 VDC
5A

PILOT'S SIDE PANEL RH AUX. TANK

1 CT E102A22
0.5A
2

PIN (5 EA) 7 5 SOCKET (5 EA)

CONNECTOR (15 EA) 6 4 CONNECTOR (15 EA)
RED 2
CT E101A22 1
GREEN SWITCH
2
BLUE "FULL"
3
9 SOCKET SOCKET 9
GRN GRN
CT E103C22 CT E104C22 8 CONNECTOR CONNECTOR 8 CT E102C22 CT E102D22
1 1 CT E102A22 1 CT E102B22 1 CT E102G22
RED 2
2 GRN GRN 2 CT E104C22 2 CT E104B22 2 CT E104A22 1
GREEN SWITCH
3 CT E105C22 CT E106C22 3 CT E106C22 3 CT E106B22 3 CT E106A22 2
BLUE "3/4"
4 4 CT E108C22 4 CT E108B22 4 CT E108A22 3
5 GRN GRN 5 CT E110D22 5 CT E110C22 5 CT E110B22
6 CT E107C22 CT E108C22 6 CT E112D22 6 CT E112C22 6 CT E112B22
CT E102E22
11 PIN PIN 11 PIN 11
RED 2
GRN GRN 10 CONNECTOR CONNECTOR 10 CONNECTOR 10 1
GREEN SWITCH
CT E109D22 CT E110D22 2
BLUE "1/2"
3
GRN 9 9 GRN RING
8 8
7 7
12
TERMINAL
YEL 2 2 YEL
3 3 RED 2
4 4 1 CT E102H22 1
GREEN SWITCH
1(+) 1(+) 2 CT E110A22 2
BLUE "1/4"
10(-) 10(-)
RING 3
12
TERMINAL

CT E102J22
CT E111D22 CT E112D22

RED 3
1
GREEN SWITCH
3 CT E112A22 2
BLUE "EMPTY"
PIN 7 5 SOCKET 3
5 26005-6001-1 (REF)
CONNECTOR 6 4 CONNECTOR RING
12
TERMINAL

26005-5001-2 FUEL LEVEL INDICATION, RH

PAGE B9
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE B10
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

WIRING DIAGRAM MANUAL

UNITS/
ITEM PART NUMBER NOMENCLATURE EFFECTIVITY
ASSY
WIRING DIAGRAM, FUEL LEVEL
26005-5001-1 1
INDICATION, LH
WIRING DIAGRAM, FUEL LEVEL
26005-5001-1 1
INDICATION, RH
1 26005-6001-1 ASSEMBLY 1
2 OPT4299-1 OPTICAL SWITCH, NO 8
LLT210D324-003 OPTICAL SWITCH, NO (ALTERNATE) 8
3 OPT4299-2 OPTICAL SWITCH, NC 2
LLT210D3L24-003 OPTICAL SWITCH, NC (ALTERNATE) 2
4 1-480303-0 RECEPTACLE, SOCKET 12
5 60617-1 SOCKET 36
6 1-480305-0 RECEPTACLE, PIN 12
7 60618-1 PIN 36
8 39-09-1061 RECEPTACLE, SOCKET 3
9 02-09-1119 SOCKET 18
10 03-09-2061 RECEPTACLE, PIN 5
11 02-09-2118 PIN 30
12 31890 RING TERMINAL 7
13 36512 RING TERMINAL 1

PAGE B11
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14
 BEECHCRAFT KING AIR 90 SERIES AUXILIARY FUEL TANKS ICA MANUAL

[Intentional Blank Page]

PAGE B12
MANUAL No. 26005-30 APPENDIX B Rev. 1, 09/01/14