OPERATING INSTRUCTIONS SCALE FACTOR Description Terminal RATE OR TOTAL DISPLAY MODE:

Programmable from 0.00001 to 9.99999x10n The RC102C toggles between RATE display and
RC102C n = -3, -2, -1, 0, 1, 2.
Short to select NPN sensor 1-2
TOTAL display at the momentary press of R/T ( )
Short to select PNP sensor 2-3
INPUTS key .In rate mode RATE LED glows & in totaliser
Count input 2 mode TOTAL LED glows.
3-30V DC from Proximity switches, Encoders,
Potential free contacts, Limit switches etc. +12V supply 4
SENSOR SUPPLY COM (GND) 6
In built 12V DC (±10%), 30 mA Reset input 5-6
INPUT SPEED Short to Filter input noise 6-7
1) 30 Hz RATE
Short to enter configuration 9 - 10
2) 2.5 kHz. press ( )
Please maintain these instructions and review Live - Neutral L (+) - N (-) key momentary
CONFIGURATION LOCK
them before using the unit:
via rear terminals.
RESET INPUT CONNECTIONS:
Warning:
1. This unit is panel mounted type with its 1) On front panel. PNP proximity sensor
2) Remote reset ( via rear terminals). PNP
output terminals getting connected to the TOTAL
O/P V+ GND
host equipment. Such equipment shall also MEMORY RETENTION
comply with basic EMI/EMC and safety 10 years. 1 2 3 4 5 6 RESETTING THE RC102C
requirements like BSEN 61326-1 and SUPPLY VOLTAGE (FACTORY SET) CNT +12V RST COM A. By front key: Press R/T key continuously
BSEN 61010 respectively. 90 to 270V AC/DC @ 50/60 Hz. Short 2 & 3
for 3 sec. The totaliser resets to zero and starts
2. To avoid electric shock, power supply of the 24V AC/DC (Optional) NOTE: For PNP sensor input, short terminals 2 & 3. counting again, and the display shows the rate
unit should be kept off while wiring. Wiring OPERATING TEMP. or total as per selection.
should be done strictly as per the terminal NPN proximity sensor
Operating: 0 to 50oC B. Remote reset:
layout, given in the manual. NPN
The RC102C can be reset from a remote push
Storage: 0 to 50oC
3. Use lugged terminals to meet M3.5 screws. O/P V+ GND
HUMIDITY button as shown in the figure below:
4. The unit does not have a built-in fuse. 1 2 3 4 5 6
External fuse with a rating of 275V AC/1A is 95% RH. Reset by potential free switch
CNT +12V RST COM
recommended. HOUSING Short 1 & 2

! Caution:
Flame retardant plastic. NOTE: For NPN sensor input, short terminals 1 & 2.
1. This unit is not intended for outdoor use. WEIGHT 1 2 3 4 5 6
250 gms. Potential free contact
2. The power connection cable must have a CNT +12V RST COM
cross-section of atleast 1mm 2 and insulation PANEL DIMENSIONS(dimensions in mm)
capacity of atleast 1.5kV. Panel Cutout
INITIALISATION:
1 2 3 4 5 6
3. The output connections must not be loaded Switch off the power. Short terminal no. 9 &10.
beyond the specified values/range. 45 46
CNT +12V RST COM Press key at the time of turning the power on.
48 Short 2 & 3
4. Avoid inflow of dust and contact of conductive The key must continue to remain pressed for
material with the internal circuitry of the unit. NOTE: Short terminals 2 & 3.
96
123 92
another 3 sec. When this sequence is correctly
5. The unit must not operate in presence of Sensor color codes:-
10 performed, the unit initialises and all parameters
heating sources, caustic vapors, oil, steam, Red = +12V, Green = CNT, Black = GND;
vibration or impact etc. MO
DEL IM A B C D E F G are set to factory settings.
D Brown = +12V, Black = CNT, Blue = GND.
6. Use clean soaked cloth cleaning. RC102C 50 97.5 10 88 45 46 92 Scale factor changes to 1 (mantissa = 1.0000 &
NOTE: exponent = 100=1), Resolution = 1, Maximum
SPECIFICATIONS: TERMINAL CONNECTION
In some applications, the proximity sensors may input frequency = 2500 Hz.Totaliser resets to 0.
DISPLAY SENSOR Short to filter
SELECTION
Type: 7 segment LED; Height: 0.5”. +12V RST
input noise
CONFIG
pick up high frequency noise form nearby After initialisation unit will go into configuration
NPN PNP COM FILTER
Counter: 6 digits, Rate: 4 digits. switching circuits like AC / DC drive, Due to this setting mode. To quit configuration setting
1 2 3 4 5 6 7 8 9 10 the counter may show erroneous reading. Short mode:
RANGE
terminals 6-7 for RC102C as shown in figure
Counter: 9999.99, 99999.9 & 999999. 22 CNT
24 1) Turn power off
above, to filter out high frequency spurious
Rate: Auto ranging (4.00 to 9999 RPM). 21 23 2) Remove link between terminal nos 9 & 10
pulses by limiting the input frequency to about
ACCURACY 200Hz (1200 RPM).
3) Turn power on.
11 12 13 14 15 16 17 18 N L
Rate: 0.05 % (± 2 count).
- + Operating/1108/RC102C/OP191-V04 (Page 1 of 2)
CONFIGURATION SCHEME 4. Press R/T key to select max.
input frequency
To enter configuration short terminals 9 & 10 R AT E TO TA L

and turn the power on.

Configure the unit as per the instructions below.
Max. input Fast speed
selec PRG R/T RC102
1. To select scale factor mantissa frequency (maximum 2500 hz)

KEY PRESS DISPLAY DESCRIPTION Slow speed

Press (maximum 30 hz )
Scale factor Set between
mantissa 0.00001 to 9.99999 5. Press R/T key to complete setting,
as described below: display will go to step 1
The blinking digit increments by 1 for every press (scale factor mantissa setting). Measuring
Wheel
of the key & rolls over from 9 to 0. The blinking To quit configuration:
digit shifts to next digit (right) for every press of 1) Turn power off.
key. Using these keys user can set the required 2) Remove link between terminal no 9 & 10. Proximity
value. 3) Turn power on. Switch

2. Press R/T key to select scale TO READ SCALE FACTOR , Calculations

RESOLUTION & SPEED Circumference of the wheel = 3.14285 x 0.1 =
factor exponent
0.314285m.
Scale factor KEY PRESS NAME / Therefore the length of rope delivered per revolution
100 = 1 DISPLAY is 0.314285m.
exponent (MOMENTARY) DESCRIPTION
Since the proximity switch gives one pulse per
Press 10 1 = 10 revolution, the display should increment by 0.314285
Scale Factor
PRG (Mantissa) for every pulse. Therefore, scale factor = 0.314285.
Press 102 = 100 Set scale factor mantissa = 3.14285 & exponent = 10-1
Scale Factor The RC102C will show rate in meters / minute & total
PRG (Exponent) in meters.
Press 10-3 = 0.001
Totaliser Least
Example 2: If 60 PPR encoder is fitted instead of
PRG Count
proximity.
Press 10 -2 = 0.01
Length of rope delivered per revolution is 0.314285m.
Maximum Input
PRG Speed Number of pulses per revolution = 60.
Length of rope delivered / pulse = 0.314285 / 60 =
Press 10-1 = 0.1
NOTE: Maximum display time is 3 sec. If the key is 0.005238m.
pressed again within 3 sec of previous key press, The display should increment by 0.005238 for every
3. Press R/T key to select totaliser display shows next parameter, otherwise it shows pulse. Therefore, scale factor = 5.23800 x 10-3
resolution rate or total as per selection. Set scale factor mantissa = 5.23800 & exponent = 10-3
for the required display.
TYPICAL APPLICATION:
Totaliser Least count = 1 Objective: To display: a. The total length of cord (in
resolution meters) that has passed over the measuring wheel Selec Controls Pvt. Ltd.
b. The delivery rate of cord (meters / minute). ( Specifications are subject to change, since development is a
Press Least count = 0.1 Data available: continuous process )
The proximity switch generates 1 pulse / revolution of Telephone: +91-22-40394200 / 40394202
the measuring wheel. The diameter of the wheel is Fax: +91-22-28471733
10cm. Toll free: 1800 227 353
Press Least count = 0.01 Website: www.selec.com
Email: [email protected]
Operating/1108/RC102C/OP191-V04 (Page 2 of 2)