Scribd
Upload
60 views1 page

TNMG 160404 NN LT 10 108

The document provides machining conditions including recommended depths of cut, feed rates, cutting speeds, and maximum chip area for a variety of materials. The materials are organized into 12 groups covering carbon and alloy steels, stainless steels, cast irons, titanium and nickel alloys, hardened materials, and aluminum. Optimal parameters such as minimum depth of cut of 0.3mm, minimum feed rate of 0.05mm/t, and minimum cutting speed of 30m/min are provided depending on the material and its hardness.

Uploaded by

fabio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
60 views1 page

TNMG 160404 NN LT 10 108

The document provides machining conditions including recommended depths of cut, feed rates, cutting speeds, and maximum chip area for a variety of materials. The materials are organized into 12 groups covering carbon and alloy steels, stainless steels, cast irons, titanium and nickel alloys, hardened materials, and aluminum. Optimal parameters such as minimum depth of cut of 0.3mm, minimum feed rate of 0.05mm/t, and minimum cutting speed of 30m/min are provided depending on the material and its hardness.

Uploaded by

fabio
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

MACHINING

CONDITIONS
TNMG 160404 NN LT 10
FT000457

Advised Advised
D.O.C Feed Amax Vc Advised Vc
Material Lamina Material D.O.C Feed
Hardness
Group Group Example max
min[mm] max[mm] min[mm/t] max[mm/t] [mm^2] min[m/min] [mm] [mm/t] [m/min]
[m/min]

125 HB 0.3 3 0.11 0.23 0.6 180 330 2 0.18 300


C35, Ck45,
Non Alloyed 1 1020, 1045, 190 HB 0.3 2.5 0.11 0.22 0.52 180 280 2 0.18 260
1060, 28Mn6
250 HB 0.3 2.5 0.11 0.2 0.48 180 250 2 0.18 240

230 HB 0.3 2.5 0.1 0.2 0.48 120 250 2 0.14 240

42CrMo4, St50, 280 HB 0.3 2 0.1 0.18 0.4 120 210 2 0.13 200
Low Alloyed 2 Ck60, 4140,
Steel

4340, 100Cr6 180 HB 0.3 2.5 0.1 0.2 0.5 120 280 2 0.14 260

350 HB 0.3 2 0.1 0.18 0.36 120 180 2 0.13 180

220 HB 0.3 2.5 0.09 0.18 0.4 70 190 1.7 0.1 180

X40CrM0V5, 280 HB 0.3 2.5 0.09 0.16 0.4 70 150 1.7 0.1 140
High Alloyed 3 H13, M42, D3,
S6-5-2, 12Ni19 320 HB 0.3 2 0.09 0.14 0.32 70 130 1.7 0.1 120

350 HB 0.3 2 0.09 0.14 0.26 70 110 1.7 0.1 110

180 HB 0.3 2.5 0.08 0.18 0.32 170 270 2 0.09 260
304, 316,
Austentic 4
X5CrNi18-9
240 HB 0.3 2.5 0.08 0.18 0.26 160 220 2 0.08 210
Stainless Steel

290 HB 0.3 2 0.08 0.14 0.2 80 150 1.7 0.08 140


X2CrNiN23-4,
Duplex 5
S31500
310 HB 0.3 2 0.08 0.14 0.2 70 140 1.7 0.08 140

200 HB 0.3 2.5 0.08 0.18 0.32 170 250 1.7 0.09 240
Ferritic & 410, X6Cr17,
6
Martensitic 17-4 PH, 430
42 HRc 0.3 2 0.08 0.16 0.26 120 190 1.5 0.08 180

150 HB 0.3 3 0.08 0.2 0.64 170 250 2 0.18 240


GG20, GG40,
Grey 7 EN-GJL-250, 200 HB 0.3 3 0.08 0.2 0.6 160 230 2 0.18 220
N030B
Cast Iron

250 HB 0.3 3 0.08 0.2 0.6 150 210 2 0.18 200

150 HB 0.3 2.5 0.08 0.18 0.48 120 250 2 0.13 240

Malleable & GGG40,


8 200 HB 0.3 2.5 0.08 0.18 0.4 120 230 2 0.13 220
Nodular GGG70, 50005

250 HB 0.3 2.5 0.08 0.18 0.4 120 190 2 0.13 180

Incoloy 800 240 HB 0.3 2 0.09 0.15 0.26 30 50 1.3 0.1 40

Fe, Ni & Co
9 Inconel 700 250 HB 0.3 2 0.09 0.15 0.26 30 50 1.3 0.1 40
Based
NiTi Alloy

Stellite 21 350 HB 0.3 2 0.09 0.15 0.26 20 50 1.3 0.1 35

T40 - 0.3 2 0.09 0.14 0.26 40 60 1.3 0.1 50


Ti Based 10
TiAI6V4 - 0.3 2 0.09 0.16 0.32 50 70 1.3 0.14 60

G-X300CrMo15 55 HRc 0.3 1.4 0.05 0.09 0.13 30 50 0.9 0.06 40


Hardened Materials

Ni-Hard 2 400 HB 0.3 1.6 0.05 0.12 0.17 40 60 1.1 0.1 50


Steel Chilled
Cast Iron
11 45 HRc 0.3 1.8 0.05 0.12 0.2 50 100 1.4 0.1 90
White Cast
Iron X100CrMo13,
440C, G- 50 HRc 0.3 1.5 0.05 0.1 0.17 40 90 1.1 0.08 80
X260NiCr42
55 HRc 0.3 1.4 0.05 0.09 0.13 40 80 0.9 0.06 70
Aluminium

AI (>8%Si) 12 AlSi12 130 HB 0.3 4 0.1 0.3 0.7 200 400 2 0.23 350

You might also like