Scribd
Upload
13 views5 pages

3.6 Konfigurasi Routing Dinamis

Uploaded by

Zahra Khaerunnisa

The document describes the configuration of dynamic routing using OSPF on three routers - Router 0, Router 1, and Router 2. It provides the configuration commands to set the IP addresses on each router interface, enable OSPF routing process 1, and add the networks to OSPF area 0. The routers are connected via their FastEthernet 0/0, Serial 2/0 and Serial 3/0 interfaces, and the configurations shown would establish OSPF routing between the three routers over these connections.

Copyright:

© All Rights Reserved
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt

3.6 Konfigurasi Routing Dinamis

Uploaded by

Zahra Khaerunnisa
13 views5 pages
The document describes the configuration of dynamic routing using OSPF on three routers - Router 0, Router 1, and Router 2. It provides the configuration commands to set the IP addresses on each router interface, enable OSPF routing process 1, and add the networks to OSPF area 0. The routers are connected via their FastEthernet 0/0, Serial 2/0 and Serial 3/0 interfaces, and the configurations shown would establish OSPF routing between the three routers over these connections.

Copyright

© © All Rights Reserved

Available Formats

DOCX, PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

The document describes the configuration of dynamic routing using OSPF on three routers - Router 0, Router 1, and Router 2. It provides the configuration commands to set the IP addresses on each router interface, enable OSPF routing process 1, and add the networks to OSPF area 0. The routers are connected via their FastEthernet 0/0, Serial 2/0 and Serial 3/0 interfaces, and the configurations shown would establish OSPF routing between the three routers over these connections.

Copyright:

© All Rights Reserved
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt
13 views5 pages

3.6 Konfigurasi Routing Dinamis

Uploaded by

Zahra Khaerunnisa
The document describes the configuration of dynamic routing using OSPF on three routers - Router 0, Router 1, and Router 2. It provides the configuration commands to set the IP addresses on each router interface, enable OSPF routing process 1, and add the networks to OSPF area 0. The routers are connected via their FastEthernet 0/0, Serial 2/0 and Serial 3/0 interfaces, and the configurations shown would establish OSPF routing between the three routers over these connections.

Copyright:

© All Rights Reserved
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt
You are on page 1/ 5

Kegiatan 6.

Konfigurasi Routing Dinamis (RIP)

Router Interface IP Address Subnet mask


Router 0 Se0/0 192.168.3.1 255.255.255.0
Se0/0 192.168.3.2 255.255.255.0
Router 1
Se0/1 192.168.4.1 255.255.255.0
Router 2 Se0/0 192.168.4.2 255.255.255.0

Persoalan:
Bagaimana perintah konfigurasi routing dinamis di atas jika menggunakan protokol routing RIP?

Penyelesaian:
Perintah konfigurasi routing dinamis ang dilakukan di atas adalah sebagai berikut.

Router 0 Router 1
R1(config)#interface serial 0/0
R0(config)#interface serial 0/0 R1(config-if)# ip address 192.168.3.2 255.255.255.0
R0(config-if)#ip address 192.168.3.1 255.255.255.0 R1(config-f)#clock rate 64000
R0(config-f)#clock rate 64000 R1(config-if)#no shutdown
R0(config-if)#no shutdown R1(config-if)#exit
R0(config-if)#exit R1(config)#interface serial 0/1
R0(config)#router rip R1(config-if)# ip address 192.168.4.1 255.255.255.0
R0(config-router)#network 192.168.3.0 R1(config-f)#clock rate 64000
R1(config-if)#no shutdown
Router 2 R1(config-if)#exit
R1(config)#router rip
R2(config)#interface serial 0/0 R1(config-router)#network 192.168.3.0
R2(config-if)#ip address 192.168.4.2 255.255.255.0 R1(config-router)#network 192.168.4.0
R2(config-f)#clock rate 64000
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#router rip
R2(config-router)#network 192.168.4.0
Kegiatan 6.7

Konfigurasi Routing Dinamis (OSPF)

IP Address
Router Subnet Mask
Fa0/0 Se2/0 Se3/0
R0 172.16.1.1 17.17.1.1 - 255.255.0.0
R1 172.16.2.1 17.17.1.2 172.17.2.1 255.255.0.0
R2 172.16.3.1 - 172.17.2.2 255.255.0.0

Penyelesaian:

Perintah konfigurasi routing dinamis di atas adalah sebagai berikut.

Router 0

R0(config)#interface serial 0/0


R0(config-if)#ip address 172.16.1.1 255.255.0.0
R0(config-if)#no shutdown
R0(config-if)#exit
R0(config)#interface serial 2/0
R0(config-if)#ip address 172.17.1.1 255.255.0.0
R0(config-f)#clock rate 64000
R0(config-if)#no shutdown
R0(config-if)#exit
R0(config)#router ospf 1
R0(config-router)#network 172.16.1.0 0.0.255.255 area 0
R0(config-router)#network 172.17.1.0 0.0.255.255 area 0
R0(config-router)#end
R0#copy running-config startup-config

Router 2

R2(config)# interface fa 0/0


R2(config-if)# ip address 172.16.3.1 255.255.0.0
R2(config-if)# no shutdown
R2(config-if)#exit
R2(config)#interface serial 3/0
R2(config-if)# ip address 172.17.2.2 255.255.0.0
R2(config-if)# clock rate 64000
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#route ospf 1
R2(config-router)#network 172.16.3.0 0.0.255.255 area 0
R2(config-router)#network 172.17.2.0 0.0.255.255 area 0
R2#copy running-config startup-config

Router 0

R0(config)#interface fa0/0

address 172.16.1.1 255.255.0.0

RO(config-if)#no shutdown

RO(config-if)#exit

RO(config)#interface serial 2/0

address 255.255-0.0

RO(config-if)#clock rate 64000

RO(config-if)#no shutdown

RO(config-if)#exit

RO(config)#route ospf 1

RO(config-router)#network 172.16.1.0 0.0,255.255 area O

0.0.255.255 area 0

RO(config-router)#end

RO#copy running-config startup-config

Router I
Rl(config)#interface faO/O

Router 2

faO/O

address 172,16.3.1 255.255.0.0

shutdown

R2(config-if)#exit

R2(config)#interface serial 3/0

address 172.17„2.2 255.255.0.0

rate 64000

R2(config-if)#no shutdown

R2(config-if)#exit

R2(config)#route ospf 1

R2(config-router)#network 172.16.3.0 0.0.255,255 area 0

R2(config-router)#network 172.17.2.0 0.0.255.255 area 0

R2#copy running-config startup-config

address 172.16.2,1 255.255,O.O

Rl(config-if)#no shutdown

Rl(config-if)#exit

Rl(config)#interface serial 2/0

address 172,17.1.2 255.255.0.0

Rl(config-if)#clock rate 64000

Rl(config-if)#no shutdown

Rl(config-if)#exit

Rl(config)#interface serial 3/0

address 17217.21 255.255.0.0

Rl(config-if)#clock rate 64000

Rl(config-if)#no shutdown
RI (config-if)#exit

Rl(config)#route ospf 1

172.16,2.0 0.0255-255 area O

Rl(config-router)#network 172.17.1.0 0.0.255.255 area 0

172.17.2.0 area O

Rl(config-router)#end

Rl#copy running-config startup-config

You might also like