Impact LX88+ User Guide ENG v2 1

User Guide
www.nektartech.com
www.nektartech.com
Content
Introduction 4
Box Content 4
Impact LX+ Features 4
Minimum System Requirements 4
Getting Started 5
Connection and Power 5
Nektar DAW Integration 5
Using Impact LX88+ as a Generic USB MIDI Controller 5
Keyboard, Octave and Transpose 6
Changing Transpose, Octave, Program, MIDI Channel and Preset with Transpose Buttons 6
Layer & Split 7
Layer 7
Split 7
Setting Octave and MIDI Channel with Transpose Buttons 7
Sending MIDI Program Messages 7
Wheels and Foot Switch 8
Pitch bend and Modulation Wheels 8
Foot Switch 8
Controlling MIDI Software 9
Mixer, Instrument and Presets 9
Global Controls 10
Function Buttons 11
Shift/Mute 11
Snapshot 11
Null 11
Pad Learn 11
Setup 11
Pads 12
Pad Maps 12
Pad Learn 12
Programming MIDI Messages to Pads 12
Pad Velocity Curves 12
Clips and Scenes buttons 12
What the Pads’ LED Colors Tell You 13
Pads Maps Default Settings 14
Setup Menu 15
Assigning Controls to MIDI messages 16
Control Assign (C1) 16
MIDI Channel Assign (D1) 16
Assignment Types (E1) 17
Data 1 and Data 2 Values (C#1 & D#1) 17
Fader Buttons and Pads LED behavior 18
Drawbar On/Off (F1) 19
Save Presets and Pad Maps (F#1) 19
Load a Preset (G1) 19
Global Functions and Options 20
Global MIDI Channel (C2) 20
Setting the Layer & Split MIDI Channels 20
Keyboard Velocity Curves (C#2) 20
Pads Velocity Curves (D2) 21
Panic (D#2) 21
Program (E2) 21
Sending Program Messages via Layer & Split 21
Bank LSB (F2) 22
Bank MSB (F#2) 22
Sending Bank LSB/MSB Messages via Layer & Split 22
Memory Dump (G2) 22
Low Power Mode 23
USB Port Setup (A2) 23
MIDI Out from USB 23
2 Nektar Impact LX88+ User Guide www.nektartech.com

User Preset 1 GM Instrument 24
User Preset 2 GM Mixer 1-8 25
User Preset 3 GM Mixer 9-16 26
User Preset 4 “Learn Friendly” 1 27
User Preset 5 “Learn Friendly” 2 28
Factory Restore 29
Dispose of product securely, avoiding exposure to food sources and ground water. Only use the product in accordance with the instructions.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Impact LX88+
CALIFORNIA PROP65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information: www.nektartech.com/prop65
Impact firmware, software and documentation are the property of Nektar Technology, Inc and subject to a License Agreement.
© 2016 Nektar Technology, Inc. All specifications subject to change without notice. Nektar is a trademark of Nektar Technology, Inc.
www.nektartech.com Nektar Impact LX88+ User Guide 3

Introduction
Thank you for buying the Nektar Impact LX88+ controller keyboard.
The Impact LX+ controllers are available in 25, 49, 61 and 88 note versions and come with setup software for many of the most popular
DAWs. This means that for supported DAWs, the setup work has largely been done and you can focus on expanding your creative horizon
with your new controller. Nektar DAW support adds functionality that makes the user experience more transparent when you combine the
power of your computer with Impact LX88+.
In addition, the Impact LX88+ allows for complete user configurable MIDI control, so if you prefer to create your own setups, you can do that
too. We hope you will enjoy playing, using and being creative with Impact LX88+ as much as we have enjoyed creating it.
Box Content
Your Impact LX88+ box contains the following items:
• The Impact LX88+ controller keyboard
• Printed Guide
• A standard USB cable
• Card containing license code for software inclusion
If any of the items above are missing, please let us know via email: [email protected]
Impact LX88+ Features
• 88 note full-sized, semi-weighted velocity sensitive keyboard • 2 read-only presets (Mixer/Instrument)

• 8 velocity sensitive, LED illuminated pads • 4 Pad Map presets
• 9 MIDI assignable faders • Shift functions for Nektar DAW Integration
• 9 MIDI assignable LED illuminated buttons • 3 character, 7 segment LED display
• 8 MIDI assignable controller pots • Layer and Split buttons
• 1 Instrument page button for Nektar DAW Integration only • MIDI out socket
• 6 transport buttons • USB port (back) and USB bus powered
• Pitch Bend and Modulation Wheels (assignable) • Power on/off switch (back)
• Transpose up/down buttons • DC socket
• Mixer, Instrument and Preset select buttons • 1/4” jack Foot Switch socket (back)
• 5 Function buttons including Mute, Snapshot, Null, Pad Learn • Connect to iPad via Apple USB Camera Connection Kit
and Setup
• 5 User configurable presets • Nektar DAW support integration
Minimum System Requirements

As a USB class compliant device, Impact LX88+ can be used from Windows XP or higher and any version of Mac OS X. The DAW Integration
files can be installed on Windows Vista/7/8/10 or higher and Mac OS X 10.7 or higher.

Getting Started
Connection and Power

The Impact LX88+ is USB Class Compliant. This means there is no driver to install to get the keyboard set up with your computer. Impact
LX88+ uses the built-in USB MIDI driver which is already part of your operating system on Windows and OS X.
This makes the first steps simple:

• Locate the included USB cable and plug one end into your computer and the other in to your Impact LX88+.
• If you want to connect a foot switch to control sustain, plug it in to the 1/4” jack socket on the back of the keyboard.
• Set the power switch on the back of the unit to On.
Your computer will now spend a few moments identifying the Impact LX88+ and subsequently you will be able to set it up for your DAW.
An optional 9V 600mA DC power supply can be connected to the DC power socket on the back of the LX88+, if you plan to use the keyboard
without a computer.
Nektar DAW Integration

If your DAW is supported with Nektar DAW Integration software, you’ll need to first create a user account on our website and subsequently
register your product to then gain access to the downloadable files applicable to your product.
Start by creating a Nektar user account here: www.nektartech.com/registration
Next follow the instructions given to register your product and finally click on the “My Downloads” link to access your files.
IMPORTANT: Make sure to read the installation instructions in the PDF guide, included in the downloaded package, to ensure you don’t miss
an important step.
Using Impact LX88+ as a Generic USB MIDI Controller

You do not need to register your Impact LX88+ in order to use your controller as a generic USB MIDI controller. It will work as a USB Class
device on OS X, Windows, iOS and Linux.
However there are several additional benefits to registering your product:
• Notification of new updates to your Impact LX88+ DAW Integration

• PDF download of this manual as well as the latest DAW Integration files
• Access to our email technical support
• Warranty service

Keyboard, Octave and Transpose
The Impact LX88 keyboard is velocity sensitive so you can play the instrument expressively. There are 4 different velocity curves to choose
from, each with varying dynamics. In addition, there are 3 fixed velocity settings.
We recommend you spend a little time playing with the default velocity curve and then determine if you need more or less sensitivity. You
can learn more about velocity curves and how to select them on page 20.
Changing Transpose, Octave, Program, MIDI Channel and Preset

with Transpose Buttons
The Transpose buttons can be used to send out MIDI program messages, change the Global MIDI channel or select the Impact LX88+’s
control presets - in addition to changing the default transpose setting.
To change the buttons function:

• Press the two Transpose buttons simultaneously.
• The display will now show the current assignment abbreviation for a little over 1 second.
• Press the Transpose up or down button to step through the options.
Below is the list of the functions that the Transpose buttons can be assigned to control. The Display column shows the text abbreviation
for each function as they appear on the Impact LX88+ display. The function remains assigned to the buttons until another function is
selected. After power cycling the default function is selected.
Display Function Value range

trA Transpose the keyboard up or down -/+ 12 semi tones
Oct Shift Octave up/down -/+ 2
PrG Sends out MIDI program change messages 0-127
GCh Change the Global MIDI Channel 1 to 16
PrE Select any of the 5 control presets 1 to 5

Layer & Split
The Impact LX88+ can send MIDI notes on a layer and split zone providing a total of 3 zones that each can send on a different MIDI
channel. If you own a multitimbral sound module, multiple synths or operate a multitimbral software instrument, you will be able to take
advantage of these features.
Layer
The layer zone is on if the Layer button is illuminated. By default the layer MIDI channel is set to 2. The global MIDI channel is set to 1 by
default, so each key press will now send two MIDI notes: One on channel 1 and another on channel 2.
Split
The split zone is on if the Split button is illuminated. By default the split point is set to F#2 (the 3rd F# from the left of the keyboard) and
the split zone is therefore the keys below F#2. The default MIDI channel for the split zone is 3.
If Layer is still on, you will be sending one MIDI note on channel 3 when playing the keys below F#2 and two MIDI notes on channel 1 and 2
when you play the notes from F#2 and up.
Setting the Split point

To change the split point, press and hold the Layer and Split buttons. Next select the new split point by pressing the corresponding key on
the keyboard. Release the Layer and Split buttons and the new split point is set.
Setting Octave and MIDI Channel with Transpose Buttons

It’s quick and easy to change layer and split settings using the configurable transpose buttons. Here is how it works:
• Assign either Octave or MIDI Channel to the Transpose buttons as described on the previous page.
• Press and hold the zone button (Layer or Split) while pressing the Transpose buttons to change the setting
for the function you selected.
• Release the zone button when done.
If for example you assign the Transpose buttons to Octave, you are able to quickly set the octave shift value independently for each of the
layer and split zones while pressing their respective buttons. Once you release the zone button, pressing the Transpose buttons will affect
only the main keyboard zone.
Sending MIDI Program Messages

MIDI program messages can be sent via the MIDI channel set up for layer or split.
• First assign Program to the Transpose buttons as described on the previous page.
• Press and hold the zone button (Layer or Split) while pressing the Transpose buttons. Each press will send out a MIDI program mes-
sage on the MIDI channel assigned to the selected zone. The program number you are sending is indicated on the display.
You can also send out a specific MIDI program change message. This is described in the Setup section.

Wheels & Foot Switch
Pitch bend and Modulation Wheels
The two wheels next to the Layer/Split and Transpose buttons are typically used for Pitch bend and Modulation.
The Pitch bend wheel is spring-loaded and automatically reverts to its center position upon release. It’s ideal to bend notes when you are
playing phrases that require this kind of articulation. The bend range is determined by the receiving instrument.
The Modulation wheel can be freely positioned and is programmed to control modulation by default.
Both the Pitch bend and the Modulation wheel are MIDI assignable with settings stored over power cycling so you don’t lose them when
you switch the unit off. Pitch bend and Modulation assignments are not part of the Impact LX88+ presets.
Foot Switch
You can connect a foot switch pedal (optional, not included) to the 1/4” jack socket on the back of the Impact LX88+ keyboard. The correct
polarity is automatically detected on boot-up, so if you plug in your foot switch after boot-up is complete, you may experience the foot
switch working in reverse. To correct that, do the following:
• Switch the Impact LX88+ off.

• Make sure your foot switch is connected.
• Switch the Impact LX88+ on.
The polarity of the foot switch should now be automatically detected.

Controlling MIDI Software
Impact LX88+ has incredible flexibility when it comes to controlling a DAW or other MIDI software. There are typically 3 different ways to
set up its many controls, though it is not uncommon to use a combination of different approaches.
1. Install the Impact DAW Integration files for use with an existing DAW (must be on our supported list).
2. Set up a DAW with controller learn.
3. Programming Impact LX88+ controls for your software.
Option 1 only requires installation of our DAW Integration files and following the included PDF guide. You will need to create a user here:
www.nektartech.com/registration and register your LX88+ to get access to the files and PDF user guide.
If you plan to use your DAW’s learn function or Impact’s presets at a later stage, we do recommend reading through this chapter in order
to understand how Impact LX88+ is structured. Lets start with an overview of what is stored in memory.
Mixer, Instrument and Presets

Impact LX88+ has 5 user configurable presets, though in reality the total amount of usable presets is 7. That‘s because the Mixer and
Instrument buttons each recall a read-only preset.
A preset contains control settings for the 9 faders, 9 fader buttons and 8 pots.
The Preset button recalls the currently selected user preset and there are 3 different ways you can recall any of the 5 presets:
1. Press and hold [Preset] while using the -/+ keys (C3/C#3) to change the preset selection.
2. Assign either the Octave or Transpose buttons to change preset (described on page 6).
3. Use the Setup menu to load a specific Preset.
Below is a list of what each of the 5 presets are programmed to by default. Each can be programmed with your own MIDI settings which
we will cover later.
Preset Description
1 GM Instrument preset
2 GM Mixer ch 1-8
3 GM Mixer ch 9-16
4 Learn friendly 1 (Fader buttons Toggle)
5 Learn friendly 2 (Fader buttons Trigger)
Presets 1, 4 and 5 are set up to transmit on the global MIDI channel. When you change the global MIDI channel (as described earlier, you
can use the Transpose buttons to do this at any time), you therefore change the MIDI channel that these presets transmit on. With 16 MIDI
channels available it means you can create 16 unique setups and just change the MIDI channel to switch between them.
A list of controller assignments for each of the 5 presets is available on pages 24-28.

Controlling MIDI Software (cont)
Global Controls
Global controls are controls that are not stored in a preset and therefore Pitch Bend/Modulation wheels plus the Foot Switch fall in this
category.
The 6 transport buttons in addition, are also global controls and assignments are stored over power cycling.
As you change presets or adjust your preset controls, global controls remain unchanged. This makes sense since Transport and keyboard
controls typically are set up to do one thing specifically.

Function Buttons
The second row of buttons below the display contains 5 function and menu buttons. The buttons primary functions are to change track
and patches in DAWs that are supported by Nektar DAW Integration.
The following describes their secondary function.
Shift/Mute
When you press and hold this button, the MIDI output from real-time controls is muted. This allows you to reposition faders and pots
without sending MIDI data.
In addition, pressing this button activates the secondary functions of buttons, screened below those buttons. So for example, press and
hold [Shift/Mute]+[Pad 4] to load Pad Map 4. Press and hold [Shift/Mute]+[Pad 2] to load Pad Map 2.
Snapshot
Pressing [Shift]+[Snapshot] will send out the current status of faders and pots. This can both be used as a status recall feature but also as a
fun experimental feature to change parameters without knowing for sure what will happen.
Null
Impact’s DAW Integration files contain automatic catch-up or soft takeover functions that avoid parameter jumping by delaying parameter
updates until a physical control position matches the value of the parameters.
The Null function works in a similar way but does not rely on feedback from your software to achieve it. It remembers your parameter
settings when you change between presets so you catch-up parameter values or “null”.
Example:
1. Select [Preset] and make sure [Shift]+[Null] is set to on.
2. Set the Transpose buttons to change presets (as described earlier) and select Preset 1.
3. Move Fader 1 to maximum (127).
4. Select Preset 2 using the Transpose buttons.
5. Move fader 1 to minimum (000).
6. Select Preset 1 using the Transpose buttons.
7. Move Fader 1 away from its minimum position and notice the display reads “Up” until you reach 127.
8. Select Preset 2 and move the fader away from the maximum position. Notice the display reads ‘dn” until you reach 000.
While “up” or “dn” is displayed, no control update values are sent to your software.
The null setting is independent for each of [Mixer], [Inst] and [Preset].
To switch the function on or off, first select [Preset] and then press [Shift]+[Null] until you see the status you want (on/off). Press [Mixer] or
[Inst] followed by pressing [Shift}+[Null] to set the setting for each of these options.
If you are using Nektar Integrated DAW support, please make sure to check the setup instructions for your DAW. Null is in some cases
required to be off because Impact LX88+ uses a different method to avoid parameter jumping.
Pad Learn
Pad learn allows you to quickly select a pad and learn a note assignment by pressing a key on the keyboard. This is explained in more
detail in the next section about Pads. To activate pad learn, press [Shift]+[Pad Learn].
Setup
Pressing [Shift]+[Setup] will mute the keyboard output and instead activate the setup menus accessible via the keyboard. Go to page 15
for more information about the setup menus.

Pads
The 8 pads are velocity sensitive and programmable with either note or MIDI switch messages. This means you can use them as regular
MIDI buttons as well as to punch out your drum beats and percussive melody parts. In addition, the pads have 4 velocity curve options and
3 fixed velocity options you can choose between, depending on what you are doing and your playing style.
Pad Maps
You can load and save up to 4 different pad setups in 4 memory locations called Pad Maps. Here is how you load Pad Maps:
• Press and hold the [Shift/Mute] button. The pad corresponding to the currently loaded Pad Map should now be illuminated.
• Press the pad that corresponds to the Pad Map you want to recall. The Pad Map has now been loaded.
Page 14 shows the 4 Pad Maps‘ default assignments. Map 1 is a chromatic scale which is continued in Map 2. If you have a drum setup
that’s laid out this way (many are), you can access drums 1-8 using Map 1 and drums 9-16 using Map 2.
Pad Learn
It’s easy to change a pad note assignment using the Pad Learn function. It works as follows:
1. Press the function button combination [Shift]+[Pad Learn]. The display will now blink, showing P1 (pad 1) as the default selected pad.
2. Hit the pad you want to assign a new note value to. The display blinks and updates to show the number of the pad you selected.
3. Press the key on the keyboard that corresponds to the note you want to assign to the pad. You can keep playing notes on the key-
board until you have found the note you want.
4. When you are done, press [Shift]+[Pad Learn] to exit and start playing your pads with the new assignment.
You can keep repeating steps 2. and 3. until you have created a complete Pad Map. Please note, the pads are muted during assignment.
Programming MIDI Messages to Pads

The pads can also be used as MIDI switch buttons. To learn more, check the Setup section that covers how controls are programmed.
Pad Velocity Curves

You can choose between 4 velocity curves and 3 fixed velocity value options. For more information about the velocity curves and how to
choose them, read about the Setup Menu and go to page 21 for details about pad velocity curves.
Clips & Scenes buttons

The two Clips & Scenes buttons are reserved for Nektar DAW Integration and do not have a function otherwise.

What the Pads‘ LED Colors Tell You
The pads‘ color coding provides information about their current status. As you change Pad Maps for instance, you will notice that the MIDI
note off color changes. This tells you which Pad Map is currently loaded:
Pad Map COLOR

1 Green
2 Orange
3 Yellow
4 Red
The above Pad Map color coding is only true when pads are programmed with MIDI notes. If you program the pads to send other MIDI
messages, the pad colors are set up in the following way:
MIDI cc: The pad illuminates depending on which value is sent. Value = 0 switch off the LED. If the value is between 1 and 126, the color is
green and if value = 127 the color is red.
MIDI cc feedback: If your DAW is capable of responding relatively to a MIDI cc message (i.e ignore the value sent), a status message can
be sent from the DAW to activate the pad LED. To set that up, the pad‘s Data 1 and Data 2 values need to be the same (see Setup, page 14
about programming Data 1 and Data 2 values) and your DAW can then send status values to illuminate the pad as follows: Value = 0 switch
off the LED. If the value is between 1 and 126, the color is green. If value = 127 the color is red.
Example: Program a pad to send MIDI cc 45 and set both Data 1 and Data 2 to 0. Set your DAW up to return MIDI cc 45 to activate the LED.
Depending on the value sent from the DAW, the pad will be off, green or red.
Program: All pad LEDs are off except one that corresponds with the last sent MIDI Program message. The active pad is illuminated Or-
ange. This enables you to always see at a glance which MIDI Program is active.

Pads Maps Default Settings
Map 1
Note Note No. Data 1 Data 2 Data 3 Chan
P1 C1 36 0 127 0 Global
P2 C#1 37 0 127 0 Global
P3 D1 38 0 127 0 Global
P4 D#1 39 0 127 0 Global
P5 E1 40 0 127 0 Global
P6 F1 41 0 127 0 Global
P7 F#1 42 0 127 0 Global
P8 G1 43 0 127 0 Global
Map 2

P1 G#1 44 0 127 0 Global
P2 A1 45 0 127 0 Global
P3 A#1 46 0 127 0 Global
P4 B1 47 0 127 0 Global
P5 C2 48 0 127 0 Global
P6 C#2 49 0 127 0 Global
P7 D2 50 0 127 0 Global
P8 D#2 51 0 127 0 Global
Map 3

P1 C3 60 0 127 0 Global
P2 D3 62 0 127 0 Global
P3 E3 64 0 127 0 Global
P4 F3 65 0 127 0 Global
P5 G3 67 0 127 0 Global
P6 A3 69 0 127 0 Global
P7 B3 71 0 127 0 Global
P8 C4 72 0 127 0 Global
Map 4

P1 C1 36 0 127 0 Global
P2 D1 38 0 127 0 Global
P3 F#1 42 0 127 0 Global
P4 A#1 46 0 127 0 Global
P5 G1 43 0 127 0 Global
P6 A1 45 0 127 0 Global
P7 C#1 37 0 127 0 Global
P8 C#2 49 0 127 0 Global

Setup Menu
The Setup menu gives access to additional functions such as control assign, load, save, selecting velocity curves and more. To enter the
menu, press the [Shift]+[Patch>] (Setup) buttons. This will mute the MIDI output of the keyboard and instead the keyboard is now used to
select menus.
When the Setup menu is active, the display will show {S.E.t.} with the 3 dots blinking for as long as the menu is active.
The chart below provides an overview of menus assigned to each key and what display abbreviations you see in the Impact LX88+ display
(in parentheses), when a key is pressed.
The functions are separated into two groups. The first group spanning C1-G1 covers control assignments and behavior, including Save
and Load of the 5 presets and 4 Pad Maps. When you press the keys in this group you first see an abbreviation showing the function. This
means you can press keys until you find exactly the menu you want without worrying about controls changing assignments. Since this
group of functions are the ones you most likely will use more regularly, this makes the menus easy to find.
The second group spanning C2-A#2 covers global and setup functions. Most of the second group functions will show you their current
status when you press a key.
On the following page we cover how each of these menus work. Note the documentation assumes you have an understanding of MIDI
including how it works and behaves. If you are not familiar with MIDI, we recommend you study MIDI before making control assignment
changes to your keyboard. A good place to start is the documentation of the software you want to control or the MIDI Manufacturers
Association www.midi.org.

Assigning Controls to MIDI messages
Since the Mixer and Instrument presets are read-only, the first 4 functions C1-E1 apply only to Presets and cannot be selected if either
Mixer or the Instrument [Inst] preset is selected. To enter the Setup menu’s assign functions, please do the following:
• Press [Preset].
• Press [Shift]+[Patch>] (Setup).
• The display now reads {S.E.t.} with the 3 display dots {…} blinking.
The Setup menu is now active and the keyboard no longer send MIDI notes when you press the keys. To exit the Setup menu, press
[Shift]+[Patch>] (Setup) again at any time.
Control Assign (C1)

This function allows you to change the MIDI CC number of a control. (Assignment type has to be MIDI CC). Most of the controls by default
are assigned to send MIDI CC message type. Here is how it works:
• Press the low C1 on your keyboard to select Control Assign. The display reads {CC}.
• Move or press a control. The value you see in the display is the currently assigned value (000-127).
• Change the value in decrements/increments using the keys with the -/+ symbols screened above (C3/C#3). The value assignment is
instant so if you exit the Setup menu after making changes, those changes remain active.
• You can also enter a specific value using the white number keys spanning G4–B5. Press Enter (C6) to accept the change.
MIDI Channel Assign (D1)

Each control within a preset can be assigned to send on a specific MIDI channel or follow the Global MIDI channel.
• Press D1, the display reads {Ch}.

• Move or press a control. The value you see in the display is the currently assigned MIDI channel (000-16). The MIDI specifications allow
for 16 MIDI channels. In addition Impact LX88+ gives you the option to select 000 which is the selection for the Global MIDI channel.
Most of the default presets assign controls to the Global MIDI channel so you may see this value when you move a control.
• You can also enter a specific selection (1-16) using the white number keys spanning G4–B5. Press Enter (C6) to accept the change.
Note: If you want to assign a button to select a specific Global MIDI Channel, read about Assignment Types on the next page.

Assignment Types (E1)
Most of the controls in the default presets are assigned to MIDI CC messages. But there are several other options and the below chart
shows you which are available for the two types of controls.
Controller Type Assignment Type Display Abbreviations

Pitch Bend, Modulation MIDI CC CC
Wheel, Faders 1-9, Pots Aftertouch At
1-8
Pitch Bend Pbd
LED Buttons 1-9, Trans- MIDI CC Toggle toG
port buttons, Foot Switch, MIDI CC Trigger/Release trG
Pads 1-8
MIDI note n
MIDI note toggle nt
MIDI Machine Control nnc
Program Prg
Global MIDI Channel GCh
select
To change an assignment type, do the following:

• Press the E1 on your keyboard to select Assign Options. The display reads {ASG}.
• Move or press a control. The type abbreviation you see in the display is the currently assigned type as per above chart.
• Change the value in decrements/increments using the keys with the -/+ symbols screened above (C3/C#3). The type change is instant
so if you exit the Setup menu after making changes, those changes remain active.
Data 1 and Data 2 Values (C#1 & D#1)

The Data 1 and Data 2 functions are required for some controller assignments as per the chart below.
Controller Type Assignment Type Data 1 Data2

Pitch Bend, Modulation MIDI CC Max value Min value
Wheel, Faders 1-9, Pots Aftertouch Max value Min value
1-8, Pots
Pitch Bend Max value Min value
Buttons 1-9, Transport MIDI CC Toggle CC value 1 CC value 2
buttons, Foot Switch, MIDI CC Trigger/Release Trigger value Release value
Pads 1-8
MIDI note Note on velocity MIDI note #
MIDI Machine Control n/a Sub-ID #2
Program n/a Message value
Global MIDI Channel n/a 1-16
select
To enter a Data 1 or Data 2 value, do the following:

• Press either C#1 or D#1 on your keyboard to select either Data 1 or Data 2. The display reads {d1} or {d2}.
• Move or press a control. The controls Data 1 or Data 2 value will be visible in the display.
• You can also enter a specific value using the white number keys spanning G4–B5. Press Enter (C6) to accept the change.

Fader Buttons and Pads LED behavior
Whether you are using any of the LED fader buttons or the 8 pads to send out a MIDI message, the LED behavior works the same way. We
already covered how the LED pads respond to MIDI feedback on page 13, but we present the information here again because it‘s relevant
to Assignment Types.
MIDI cc: The pad illuminates depending on which value is sent. Value = 0 switch off the LED. If the value is between 1 and 126, the color is
green and if value = 127 the color is red.
MIDI cc feedback: If your DAW is capable of responding relatively to a MIDI cc message (i.e. ignore the value sent), a status message can
be sent from the DAW to activate the pad LED. To set that up, the pad‘s Data 1 and Data 2 values need to be the same (see Setup, page 17
about programming Data 1 and Data 2 values) and your DAW can then send status values to illuminate the pad as follows: Value = 0 switch
off the LED. If the value is between 1 and 126, the color is green. If value = 127 the color is red.
Example: Program a pad to send MIDI cc 45 and set both Data 1 and Data 2 to 0. Set your DAW up to return MIDI cc 45 to activate the LED.
Depending on the value sent from the DAW, the pad will be off, green or red.
Program (Orange): All pad LEDs are off except one that corresponds with the last sent MIDI Program message. The active pad is illuminat-
ed Orange. This enables you to always see at a glance which MIDI Program is active.
Global MIDI Channel select (Yellow): If a button or pad has been assigned to send the Global MIDI Channel select message type , the LED
will only illuminate when the actual Global MIDI Channel = the button‘s programmed Global MIDI Channel.
This means that if you press the button, it will set the Global MIDI Channel to what the button was programmed to and the button will
illuminate yellow. If the Global MIDI Channel is subsequently set either by pressing a button or pad that has been assigned to select a
different MIDI channel, or any of the other two options to change the Global MIDI Channel, the LED will turn off.
For example, if you primarily want to use the 8 LED buttons to select the Global MIDI channel, it means that only the button corresponding
to the current channel will be illuminated yellow. The others will be off.

Drawbar On/Off (F1)
The Drawbar function reverses the value output of the 9 faders from the default 0-127 to 127-0. This can also be achieved by reversing the
min/max values of a control when you program Data 1 and Data 2. However if you don’t want to change the reversal permanently in your
preset, this function is ideal and here is how to activate it:
• Press F1. The display will show {drb} and then alternate with the function status (on or off).
• Change the status, using the keys with the -/+ symbols screened above (C3/C#3).
The change is immediate so to try out the setting just press [Shift]+[Setup] to exit the Setup menu.
Save Presets and Pad Maps (F#1)

When you make assignment changes to a control or pad, the changes are stored in a current working memory area and the settings are
also stored over power cycling.
However if you change preset or Pad Map your settings will be lost because the loaded data will overwrite your programmed changes. If
you don’t want to lose your work we recommend saving as soon as you have created your setup. Here is how to do that:
Save a Preset
• Press F#1 to activate the Save menu. The display will read {SAu} (yeah, that’s supposed to be a v).
• Select the Preset you want to save to, using the keys with the -/+ symbols screened above (C3/C#3).
• You can also enter a specific preset number (1-5) using the white number keys spanning A4–E5).
• Press [Enter] (C6) to save to the selected Preset location (applicable for both selection methods).
Save a Pad Map

• Press F3 to activate the save menu. The display will read {SAu} (yeah, that’s supposed to be a v).
• Press [Enter] (second to last C key on your keyboard) to confirm menu selection.
• Press [Shift] and the pad corresponding to the Pad Map you want to save your pad settings to (1-4).
• Press [Enter] (C6) to save to the selected Pad Map location.
Load a Preset (G1)

We explained earlier how you can use the Transpose buttons to select presets. Here is an alternative option for loading presets so you
don’t have to change your button functions.
• Press G1 to activate the Load menu. The display will read {Lod} (better than Loa, right?).
• Select the Preset you want to load using the keys with the -/+ symbols screened above (C3/C#3). Presets are loaded instantly as you
step through them.
• You can also enter a specific preset number (1-5) using the white number keys spanning A4–E5. Press Enter (C6) to load the selected
Preset location (only applicable when loading using the number entry option).

Global Functions and Options
Unlike the Control Assign functions, Global functions can be accessed regardless of what preset has been selected. And just to recap:
Pressing [Shift]+[Patch>] (Setup) buttons will activate the Setup menu and the display will show {S.E.t.} with the 3 dots blinking for as long
as the menu is active. The following assumes the Setup menu is active.
Global MIDI Channel (C2)

The Impact LX88+ keyboard always transmits on the Global MIDI Channel, but this setting also affects any control or pad that is not
assigned to a specific MIDI channel (i.e. 1-16). Earlier we learned how the Transpose buttons can be set up to change the Global MIDI Chan-
nel but here is another option:
• Press the C2 key on your keyboard to select Global MIDI Channel. The display shows the current value {001-016}.
instant. So if you exit the Setup menu after making changes, those changes remain active.
Setting the Layer & Split MIDI Channels (C2)

MIDI channel can also be set independently for layer and split on the Impact LX88+. On page 7 we covered how to set MIDI Channel using
the Transpose buttons, but you can also set the MIDI channel for Layer and Split in the Setup menu:
• Press the C2 key on your keyboard to select Global MIDI Channel. The display shows the current value {001-016}.
• Press and hold the [Layer] or [Split] button. The selected button will now blink.
• Change the value in decrements/increments using the keys with the -/+ symbols screened above (C3/C#3). Press Enter (C6) to accept
the change.
Keyboard Velocity Curves (C#2)

There are 4 different keyboard velocity curves and 3 fixed velocity levels to choose between, depending on how sensitive and dynamic you
want the Impact LX88+ keyboard to play.
Name Description Display Abbreviation

Normal Focus on mid to high velocity levels uC1
Soft The most dynamic curve with a focus on the low to uC2
mid velocity levels
Hard Focus on the higher velocity levels. If you don‘t like uC3
exercising your finger muscles, this may be the one
for you
Linear Approximates a linear experience from low to high uC4
127 Fixed Fixed velocity level at 127 uF1
Here is how you change a velocity curve:

• Press the C#2 key on your keyboard to select Velocity Curve. The display show the current selection.
instant. So if you exit the Setup menu after making changes, those changes remain active.
• You can also enter a specific selection (1-7) using the white number keys spanning A4–G5. Press Enter (C6) to accept.

Pads Velocity Curves (D2)
There are 4 different pad velocity curves and 3 fixed velocity levels to choose between, depending on how sensitive and dynamic you want
the Impact LX88+ pads to play.
Name Description Display Abbreviation

Normal Focus on mid to high velocity levels PC1
Soft The most dynamic curve with a focus on the low to PC2
mid velocity levels
Hard Focus on the higher velocity levels. If you don‘t like PC3
exercising your finger muscles, this may be the one
for you
Linear Approximates a linear experience from low to high PC4
127 Fixed Fixed velocity level at 127 PF1
Here is how you change a velocity curve:

• Press the D2 key on your keyboard to select Velocity Curve. The display shows the current selection.
• You can also enter a specific selection (1-7) using the white number keys spanning A4–G5. Press Enter (C6) to accept the change.
Panic (D#2)
Panic sends out the all notes off and reset all controllers MIDI messages on all 16 MIDI channels. This happens the minute you press D#2
and the Setup menu will exit upon release of the key.
Program (E2)
Earlier in this guide we covered how you can send MIDI program change messages using the Octave and Transport buttons. However,
there may be times when the Transpose buttons are deeded for another function or you want to send out a specific MIDI program change
message without having to inc/dec to get to it. This function allows you to do that:
• Press the E2 key on your keyboard to select Program. The display shows the last sent program message or 000 by default.
the change and send out the selected MIDI program message.
Sending Program Messages via Layer & Split (E2)

MIDI Program messages can also be sent independently for layer and split on the Impact LX+88. On page 13 we covered how to set it using
the transpose buttons but you can also send a MIDI Program message on the Layer and Split MIDI channels, in the Setup menu.
• Press the E2 key on your keyboard to select Program. The display show the last sent program message or 000 by default.
• Press and hold the [Layer] or [Split] button. The selected button will now blink.
the change and send out the selected MIDI program message.
• You can also enter a specific selection (0-127) using the white number keys spanning G4–B5(. Press Enter (C6) to accept the change.

Bank LSB (F2)
This function will send a Bank LSB MIDI message from the keyboard. Note, most software products don’t respond to Bank change messag-
es but many MIDI hardware products do. Here is how you send out a Bank LSB message:
• Press the F2 key on your keyboard to select Bank LSB. The display show the last sent Bank message or 000 by default.
the change and send out the selected Bank LSB message.
Bank MSB (F#2)

This function will send a Bank MSB MIDI message from the keyboard. Note, most software products don’t respond to Bank change mes-
sages but many MIDI hardware products do. Here is how you send out a Bank MSB message:
• Press the F#2 key on your keyboard to select Bank MSB. The display show the last sent Bank message or 000 by default.
the change and send out the selected Bank MSB message.
Sending Bank LSB/MSB Messages via Layer & Split (F2 & F#2)
MIDI Program messages can also be set independently for layer and split on the Impact LX88+.
• Press the F2 (or F#2) key on your keyboard to select Program. The display show the last sent Bank message or 000 by default
• Press and hold the [Layer] or [Split] button. The selected button will now blink
the change and send out the selected MIDI Bank message
• You can also enter a specific selection (0-127) using the white number keys spanning G4–B5(. Press Enter (C6) to accept the change
Memory Dump (G2)

The Memory Dump function will back up your current controller assignment settings including the 5 user presets by sending out MIDI
Sysex data. The data can be recorded in your DAW or other application capable of recording Sysex data and replayed/sent back to your
Impact LX88+ keyboard when you want to reload your settings.
Sending out a memory dump for backup:

• Make sure your MIDI software program is set up and capable of recording MIDI Sysex data
• Start recording
• Press the G2 key on your keyboard to activate the memory dump. The display reads {SYS} while the data is being sent.
• Stop recording when the display reads {000}. The content of your Impact LX88+ memory should now be recorded in your MIDI soft-
ware program
Restoring a backup:
A memory dump/backup MIDI Sysex file can be sent to the Impact LX88+ at any time, while the unit is powered on, in order to restore a
backup. Make sure the Impact LX88+ is the output destination of the MIDI track containing the backup data. The display will read {SyS}
when data is received. Once the data has transmission has been completed, the backup has been restored.

Low Power Mode(G#2)
LX88+ can be run at lower power to enable connectivity and powering from an iPad, or to conserve battery power when running it with a
laptop. When Low Power Mode is on, all LEDs are permanently off. To enable the LEDs again, Low Power Mode should be switched off.
There are a couple of ways the LX88+ can enter and exit Low Power Mode:
• With LX88+ off, press and hold the [Cycle]+[Record] buttons and switch the unit on.
• Release the buttons once the unit has powered up. Low Power Mode is now active while the unit is on.
• When activated in this manner, the Low Power Mode is not stored when you switch the LX88+ off.
You can also set Lower Power Mode so the setting is stored when the LX88+ is switched off:
• Make sure LX88+ is on and enter [Setup].
• Press G#2 and change the setting to On by using the -/+ keys.
USB Port Setup (A2)

Impact LX88+ has one physical USB port however there are 2 virtual ports as you may have discovered during the MIDI setup of your
music software. The additional virtual port is used by the Impact DAW software to handle communication with your DAW. You only need to
change the USB Port Setup setting if the Impact LX88+ setup instructions for your DAW specifically advises that this should be done.
MIDI Out from USB (A#2)

The MIDI out jack on the back of the Impact LX88+ can be used to route MIDI messages directly from the Impact LX88+ keyboard and
controls to external hardware. This is the default operation.
It’s also possible to use the MIDI out as a USB to MIDI interface, which means that if you are using a music application on your computer,
you can route MIDI messages from the application to external hardware via the built-in MIDI port. Here is how you change the port setting:
• Press the A#2 key on your keyboard to view the current setting (off or on).
• Toggle the on/off setting using the keys with the -/+ symbols screened above (C3/C#3).
• When the display reads {On} the MIDI output acts as a USB to MIDI interface.
• The change is immediate so you can check if the setting is correct before leaving the Setup menu.

User Preset 1 GM Instrument
Faders
Ctrl Msg Type CC Data 1 Data 2 Chan Param

F1 MIDI CC 73 127 0 Global Attack
F2 MIDI CC 75 127 0 Global Decay
F3 MIDI CC 72 127 0 Global Release
F4 MIDI CC 91 127 0 Global Effect depth 1 (Reverb
Send level)
F5 MIDI CC 92 127 0 Global Effect depth 2
F6 MIDI CC 93 127 0 Global Effect depth 3 (Chorus
send level)
F9 MIDI CC 7 127 0 Global Volume
Buttons

B1 MIDI CC (Toggle) 0 127 0 Global Bank MSB
B2 MIDI CC (Toggle) 2 127 0 Global Breath
B3 MIDI CC (Toggle) 3 127 0 Global Control Change (Unde-
fined)
B4 MIDI CC (Toggle) 4 127 0 Global Foot Controller
B5 MIDI CC (Toggle) 6 127 0 Global Data Entry MSB
B6 MIDI CC (Toggle) 8 127 0 Global Balance
B7 MIDI CC (Toggle) 9 127 0 Global Control Change (Unde-
fined)
B8 MIDI CC (Toggle) 11 127 0 Global Expression Controller
B9 MIDI CC (Toggle) 65 127 0 Global Portamento On/Off
Fader

K1 MIDI CC 74 127 0 Global Brightness
K2 MIDI CC 71 127 0 Global Harmonic Content
K3 MIDI CC 5 127 0 Global Portamento Rate
K4 MIDI CC 84 127 0 Global Portamento Depth
K5 MIDI CC 78 127 0 Global Control Change (Vibrato
Delay)
Rate)
Depth)
K8 MIDI CC 10 127 0 Global Pan
Note: B9 is assigned to MIDI cc 65 on all presets intended to be available for a global function

User Preset 2 GM Mixer 1-8
Faders

F1 MIDI CC 7 127 0 1 CH1 Volume
F9 MIDI CC 7 127 0 G Selected CH Volume
Buttons

B1 MIDI CC (Toggle) 12 127 0 1 Mute
B9 MIDI CC (Toggle) 65 127 0 Global Portamento
Fader

K1 MIDI CC 10 127 0 1 CH Pan

User Preset 3 GM Mixer 9-16
Faders

F9 MIDI CC 7 127 0 G Selected CH Volume
Buttons

B9 MIDI CC (Toggle) 65 127 0 Global Portamento
Fader


User Preset 4 “Learn Friendly” 1
Faders
Ctrl Msg Type CC Data 1 Data 2 Chan

F1 MIDI CC 80 127 0 Global
Buttons

B1 MIDI CC (Toggle) 66 127 0 Global
Fader

K1 MIDI CC 89 127 0 Global

User Preset 5 “Learn Friendly” 2
Faders

Buttons

B1 MIDI CC (Trig) 66 127 0 Global
Fader


Factory Restore
If you need to restore factory settings, for example if you managed to change the assignments needed for DAW integration files by mistake,
here is how you do that:
• Make sure your Impact LX88+ is switched off.

• Press the [Layer]+[Split] buttons simultaneously.
• Switch your Impact LX88+ on.
• Keep holding the buttons for 3 seconds, then release.

www.nektartech.com
Designed by Nektar Technology, Inc

Made in China
(Rev 2)

Impact LX88+ User Guide ENG v2 1

Uploaded by

Copyright:

Available Formats

Impact LX88+ User Guide ENG v2 1

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Impact LX88+ User Guide ENG v2 1

Uploaded by

Copyright:

Available Formats

User Guide

2 Nektar Impact LX88+ User Guide www.nektartech.com

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

For more information: www.nektartech.com/prop65

www.nektartech.com Nektar Impact LX88+ User Guide 3

Impact LX88+ Features

• 88 note full-sized, semi-weighted velocity sensitive keyboard • 2 read-only presets (Mixer/Instrument)

Minimum System Requirements

4 Nektar Impact LX88+ User Guide www.nektartech.com

Connection and Power

This makes the first steps simple:

Nektar DAW Integration

Start by creating a Nektar user account here: www.nektartech.com/registration

Using Impact LX88+ as a Generic USB MIDI Controller

• Notification of new updates to your Impact LX88+ DAW Integration

www.nektartech.com Nektar Impact LX88+ User Guide 5

Changing Transpose, Octave, Program, MIDI Channel and Preset

To change the buttons function:

Display Function Value range

6 Nektar Impact LX88+ User Guide www.nektartech.com

Setting the Split point

Setting Octave and MIDI Channel with Transpose Buttons

Sending MIDI Program Messages

www.nektartech.com Nektar Impact LX88+ User Guide 7

Pitch bend and Modulation Wheels

• Switch the Impact LX88+ off.

The polarity of the foot switch should now be automatically detected.

8 Nektar Impact LX88+ User Guide www.nektartech.com

Mixer, Instrument and Presets

www.nektartech.com Nektar Impact LX88+ User Guide 9

10 Nektar Impact LX88+ User Guide www.nektartech.com

The following describes their secondary function.

www.nektartech.com Nektar Impact LX88+ User Guide 11

Programming MIDI Messages to Pads

Pad Velocity Curves

Clips & Scenes buttons

12 Nektar Impact LX88+ User Guide www.nektartech.com

Pad Map COLOR

www.nektartech.com Nektar Impact LX88+ User Guide 13

Note Note No. Data 1 Data 2 Data 3 Chan

Note Note No. Data 1 Data 2 Data 3 Chan

Note Note No. Data 1 Data 2 Data 3 Chan

Note Note No. Data 1 Data 2 Data 3 Chan

14 Nektar Impact LX88+ User Guide www.nektartech.com

www.nektartech.com Nektar Impact LX88+ User Guide 15

Control Assign (C1)

MIDI Channel Assign (D1)

• Press D1, the display reads {Ch}.

16 Nektar Impact LX88+ User Guide www.nektartech.com

Controller Type Assignment Type Display Abbreviations

To change an assignment type, do the following:

Data 1 and Data 2 Values (C#1 & D#1)

Controller Type Assignment Type Data 1 Data2

To enter a Data 1 or Data 2 value, do the following:

www.nektartech.com Nektar Impact LX88+ User Guide 17

18 Nektar Impact LX88+ User Guide www.nektartech.com