Scribd
Upload
66 views2 pages

Mech662 Test-Exam Set A

This document provides instructions for a lab report assignment on wireless communications. Students will use MATLAB to: 1) Generate a 95Hz cosine wave and 190Hz sine wave, add them, and plot the amplitude spectrum with a 3.5kHz sampling rate. 2) Develop a model, record and present the data in graphs, analyze the output, interpret the results, and submit a group report. The assignment is worth a total of 100 points and will be graded based on rubrics evaluating the accuracy of the model, data presentation, analysis, interpretation, and report.

Uploaded by

مبنيةنميب نتمبيةن
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
66 views2 pages

Mech662 Test-Exam Set A

This document provides instructions for a lab report assignment on wireless communications. Students will use MATLAB to: 1) Generate a 95Hz cosine wave and 190Hz sine wave, add them, and plot the amplitude spectrum with a 3.5kHz sampling rate. 2) Develop a model, record and present the data in graphs, analyze the output, interpret the results, and submit a group report. The assignment is worth a total of 100 points and will be graded based on rubrics evaluating the accuracy of the model, data presentation, analysis, interpretation, and report.

Uploaded by

مبنيةنميب نتمبيةن
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Doc No.

QR-FMD-001
Rev No: 00
SET A
Date of Effectivity:01-09-23
Doc No. QR-FMD-001
Rev No: 00
Date of Effectivity:01-09-23

COLLEGE OF ENGINEERING
1st Tri, SY 2023-2024
MECH662A – WIRELESS COMMUNICATIONS
Lab Report 1
Time Frame: 1.5 Hour Total Points: 100

General Instructions:
 Present your student ID when you are called. No ID, No Test/Exam;
 Mobile phones or any electronic gadgets are not allowed while the test/exam is going on;
 Anyone caught cheating in any form shall have a zero mark in the course;
 Conversation in any language among students during test/exam is prohibited;
 Use black or blue pen only if there is any question(s) which needs writing and uploading to the
Moodle;
 Use a calculator for the computational skills;
 Leaving the class while the test/exam is going on is strictly prohibited;
 Read and follow instructions of each part of the test/exam very carefully.
Answer the following:
Objectives
1. To understand how to construct a sampled signal in MATLAB
2. To study the MATLAB function required for analyzing the signal in the
frequency domain
3. To display the simulation result of amplitude spectrum of signal
Equipment Use: MATLAB SIMULINK/ https://www.mathworks.com/ (Mathworks
account)
1. Analyse the signals given below and plot the amplitude spectrum of the sum of
these two signals with sampling rate of 3.5kHz
i) Generate a segment of 95 Hz cosine wave for the duration of 35 ms
ii) Create a second sine wave, with a frequency double than that of first, and add it
to the first signal that we have and display it in 2 graphs
. Observe the output.
a) Development of model and Recorded & presented data in graph (25)
b) Analyzed the overall output of simulation (25)
c) Interpret the output and shown result (25)
d) Perform in group and Submit Report (25)
Doc No. QR-AAD-007 Rev No: 02 Date of Effectivity: 01-09-23
Doc No. QR-FMD-001
Rev No: 00
Date of Effectivity:01-09-23
Doc No. QR-FMD-001
Rev No: 00
Date of Effectivity:01-09-23

Rubrics:
Question 1a
20-25 marks: Developed the model and the Required data are correctly and properly recorded in graph.
15-20 marks: Partially correct model, Partially correct data & presentation in graph
0 – 15 marks: Incorrect model with missing blocks, incorrect presentation in graph
Question 1b
20-25 marks: Completely analyzed the overall output of simulation
15-20 marks: Partially correct output of simulation
0 – 15 marks: incorrect output of simulation
Question 1c
20-25 marks: Completely Interpret the output and shown result
15-20 marks: Partially correct the interpret the output
0 – 15 marks: incorrect interpret the output and not shown result
Question 1d
20-25 marks: Perform in group and report completely correct
15-20 marks: Partially correct report
0 – 15 marks: incorrect report

Doc No. QR-AAD-007 Rev No: 02 Date of Effectivity: 01-09-23

You might also like