Jura F9 User Manual

JURA F9 Instructions for Use
The Instructions for Use has been awarded the seal of approval by the
independent German Technical Inspection Agency, TÜV SÜD, due to its
easy-to-understand style, its thoroughness and coverage of safety
aspects.
Table of contents
Your JURA F9
Control elements 4
Important information 6
Proper use....................................................................................................................................................... 6
For your safety................................................................................................................................................ 6
1 Preparing and using for the first time 10
JURA on the Internet.....................................................................................................................................10
Setting up the machine...............................................................................................................................10
Filling the bean container............................................................................................................................10
First-time use.................................................................................................................................................10
Determining the water hardness...............................................................................................................13
Connecting milk............................................................................................................................................14
Filling the water tank....................................................................................................................................14
2 Preparation 15
Ways of preparing a beverage....................................................................................................................15
Ristretto, espresso and coffee.....................................................................................................................16
Two ristretti, two espressi and two coffees..............................................................................................16
Latte macchiato, cappuccino and other speciality coffees with milk..................................................17
Ground coffee................................................................................................................................................18
Permanently setting the amount of water for the cup size..................................................................19
Adjusting the grinder..................................................................................................................................20
Hot water.......................................................................................................................................................20
3 Daily operation 21
Switching on the machine...........................................................................................................................21
Daily maintenance........................................................................................................................................21
Regular maintenance.................................................................................................................................. 22
Switching off the machine.......................................................................................................................... 22
4 Permanent settings in programming mode 23
Product settings...........................................................................................................................................24
Adjusting the product settings..................................................................................................................24
Replacing products on the start screen...................................................................................................25
Renaming a product....................................................................................................................................26
Automatic switch-off................................................................................................................................... 27
Energy-saving mode...................................................................................................................................28
Maintenance settings..................................................................................................................................28
Setting the water hardness........................................................................................................................29
Display settings............................................................................................................................................30
Unit for amount of water............................................................................................................................30
Restore factory settings...............................................................................................................................31
Language........................................................................................................................................................31
Querying information................................................................................................................................. 32
2
Table of contents
5 Maintenance 33
Rinsing the machine.................................................................................................................................... 33
Rinsing the milk system..............................................................................................................................34
Cleaning the milk system...........................................................................................................................34
Dismantling and rinsing the dual spout..................................................................................................35
Inserting and activating the filter..............................................................................................................36
Changing the filter....................................................................................................................................... 37
Cleaning the machine.................................................................................................................................39
Descaling the machine ...............................................................................................................................40
Descaling the water tank............................................................................................................................42
Cleaning the bean container......................................................................................................................42
6 Display messages 43
7 Troubleshooting 44
8 Transport and environmentally friendly disposal 45
Transport / Emptying the system..............................................................................................................45
Disposal..........................................................................................................................................................45
9 Technical data 46
10 Index 47
11 JURA contact details / Legal information 52
Symbol description
Warnings
J WARNING Always take note of any information marked with the words CAUTION or
J CAUTION WARNING and a warning sign. The signal word WARNING draws your attention
to potential serious injury, and the signal word CAUTION to potential minor
injury.
CAUTION CAUTION draws your attention to potential damage to the machine.
Symbols used
T Prompt to take action. This symbol means that you are being prompted to
perform some action.
E Information and tips to make it even easier to use your JURA F9.
‘Espresso’ Display
3
Control elements
Control elements
10
1
2 11
12
4 13
14
1 Bean container with aroma preservation 8 Filler funnel cover

cover 9 Filler funnel for ground coffee
2 Water tank cover 10 Storage compartment cover
3 Water tank 11 Grinder adjustment switch
4 Power switch and mains cable 12 Measuring spoon for ground coffee
(back of the machine) 13 Hot-water spout
5 Coffee grounds container 14 Height-adjustable dual spout
6 Drip tray
7 Cup grille
4
Control elements
1 2 3
Top of the machine Front

1 Q On/Off button 4 Display
2 g Rotary Switch 5 Multi-function buttons (button function
3 O P button (programming) depends on what is shown in the display)
6 l Switch for hot water preparation
5
Important information
Proper use The machine is designed and intended for private
domestic use. It should only be used for coffee
preparation and to heat milk and water. Use for any
other purpose will be deemed improper. JURA
Elektroapparate AG cannot accept any responsibil-
ity for the consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty ser-
vice is not applicable for damage or defects caused
by non-compliance with the instructions for use.
Keep these instructions for use close to the machine
and pass them on to the next user.
For your safety Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
J
UU Never use a machine which is damaged or has
a defective mains cable.
UU In the event of signs of damage, for example if
there is a smell of burning, unplug the machine
immediately from the mains supply and con-
tact JURA service.
UU If the mains cable of this machine is damaged,
it must be repaired either directly by JURA or
by an authorised JURA service centre.
UU Make sure that the JURA F9 and the mains
cable are not located close to hot surfaces.
UU Be careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
6
UU Never open and repair the machine yourself.

Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
UU To completely and safely disconnect the
machine from the power supply, first switch off
the JURA F9 using the On/Off button and then
at the power switch. Only then should you
remove the mains plug from the power socket.
There is a risk of scalds or burns on the spouts.
UU Place the machine out of the reach of children.
UU Do not touch any hot parts. Use the handles
provided.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
UU Never allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
UU Protect the JURA F9 from environmental influ-
ences such as rain, frost and direct sunlight.
UU Do not immerse the JURA F9, mains cable or
connections in water.
UU Do not put the JURA F9 or any individual parts
in the dishwasher.
UU Switch your JURA F9 off at the power switch
before any cleaning operation. Always wipe
the JURA F9 with a damp cloth rather than a
wet one, and protect it from prolonged expo-
sure to water splash.
7
UU Only connect the machine to the mains volt-

age in accordance with the information on the
rating plate. The rating plate is located on the
underside of your JURA F9. Further technical
data is provided in these instructions for use
(see Chapter 9 ‘Technical data’).
UU Connect the JURA F9 directly to a domestic
power socket. Using multi-socket adapters or
extension cords may cause overheating.
UU Please only use original JURA maintenance
products. Use of products that are not explic-
itly recommended by JURA could damage the
JURA F9.
UU Do not use any coffee beans treated with addi-
tives or caramelised coffee beans.
UU Only fill the water tank with fresh, cold water.
UU Switch the machine off at the power switch if
you are going to be absent for a longer period
of time.
UU Children may not clean or service the machine
unless supervised by a responsible person.
UU Do not allow children to play with the machine.
UU Keep children under the age of 8 away from
the machine, or supervise them constantly.
UU Children aged 8 and over may only operate
the machine without supervision if they have
been instructed in how to use it safely. Chil-
dren must be able to recognise and under-
stand the potential dangers arising from incor-
rect use.
8
People, including children, who

UU do not have the physical, sensory or mental
capabilities to use the machine safely or
UU are inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it cor-
rectly.
Safety when handling the CLARIS Blue filter
cartridge:
UU Filter cartridges should be kept out of the
reach of children.
UU Store filter cartridges in a dry place in the
sealed packaging.
UU Protect cartridges from heat and direct sun-
light.
UU Do not use damaged filter cartridges.
UU Do not open filter cartridges.
9
1 Preparing and using for the first time
JURA on the Internet Visit us on the Internet. You can download short operating instruc-
tions for your machine from the JURA website (www.jura.com). You
will also find interesting and up-to-date information on your JURA
F9 and on every aspect of coffee.
Setting up the machine When setting up your JURA F9, please note the following:
UUPlace the JURA F9 on a horizontal surface that is not sensitive
to water.
UUChoose a spot for your JURA F9 which protects the machine
against overheating. Ensure that the ventilation slots are not
covered.
Filling the bean container
CAUTION Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean con-
tainer.
T Remove the aroma preservation cover.

T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
First-time use When using the machine for the first time, you can choose whether
you want to operate JURA F9 with or without the CLARIS Blue filter
cartridge. If the water hardness is 10 °dH or more, we recommend
using the filter cartridge. If you do not know the hardness of your
water, you can find this out first (see Chapter 1 ‘Preparing and using
for the first time – Determining the water hardness’).
10
J WARNING If the machine is operated with a defective mains cable, there is a

danger of potentially fatal electric shock.
T Never use a machine which is damaged or has a defective
mains cable.
Precondition: The bean container has been filled.

T Insert the mains plug into a power socket.
3 T Switch on the JURA F9 using the power switch on the back
of the machine.
Q T Press the On/Off button to switch the JURA F9 on.
The display shows the languages you can choose from.
EE To display more languages, press the ‘ > ’ button (bottom

right).
T Press the button that corresponds to the language you want,

e.g. ‘English’.
‘Saved’ appears briefly on the display to confirm the setting.
‘Use filter’
EE Now decide whether you want to operate your JURA F9 with

or without a CLARIS Blue filter cartridge.
First-time use with filter

cartridge activation
CAUTION Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Press the ‘Active’ button.

T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Insert filter’
T Remove the water tank and rinse it with cold water.
T Open the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
EE After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
11
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Press the ‘Next’ button.
‘Switch open’
T Place a receptacle under the hot-water spout and dual spout.
l T Turn the switch to the m position.
‘Filter is being rinsed’, water flows out of the hot-water
spout.
EE You can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EE The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately

300 ml. ‘Switch close’ appears on the display.
y T Turn the switch to the ° position.
‘System is filling’, the system fills up with water.
‘Machine is heating’, the machine heats up.
‘Machine is rinsing’, the system is rinsed. The rinse stops
automatically. ‘Please select product’ appears on the display.
Your JURA F9 is ready for use.
EE The display shows the products you can prepare.
First-time use without filter

cartridge activation
T Press the ‘Inactive’ button.

‘Water hardness’
EE If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
12
g T Turn the Rotary Switch to change the water hardness set-

ting, e.g. to ‘25 °dH’.
‘Fill water tank.’
tank.
‘Switch open’

‘System is filling’, water flows out of the hot-water spout.
The operation stops automatically. ‘Switch close’ appears on
the display.
‘System is filling’, the system fills up with water.
‘Machine is heating’, the machine heats up.
EE The display shows the products you can prepare.
Determining the water You can find out what the water hardness is by using the Aquadur®
hardness test strip supplied as standard.
T Hold the test strip briefly (for 1 second) under flowing water.
Shake off the water.
T Wait for about 1 minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
13
Connecting milk Your JURA F9 creates fine, creamy, feather-light milk foam with a
perfect consistency. The most important requirement for frothing
milk is a milk temperature of 4–8 °C. We would therefore recom-
mend using a milk cooler or a vacuum milk container.
T Remove the protective cover from the dual spout.
T Connect the milk pipe to the dual spout.

T Connect the other end of the milk pipe to a milk container
or immerse it in a milk carton.
Filling the water tank Daily maintenance of the machine and hygiene when handling milk,
coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
T Open the water tank cover.

tank.
T Close the water tank cover.
14
2 Preparation
2 Preparation
EE You can stop the machine at any time while a speciality coffee
or hot water is being prepared. Just press any button (for a
speciality coffee) or return the switch to its original position
(for hot water preparation).
EE During the grinding operation you can select the coffee
strength of single products by turning the Rotary Switch g.
EE During preparation, you can change the preset amount of
water or milk foam by turning the Rotary Switch g.
EE You can follow the current status of preparation on the display.
Coffee tastes best served hot. A cold porcelain cup cools the bever-
age – and impairs the taste. We therefore recommend prewarming
the cups. The full coffee aroma can develop only in prewarmed cups.
You can purchase a JURA cup warmer from your specialised dealer.
You can make permanent settings for all products in programming

mode (see Chapter 4 ‘Permanent settings in programming mode –
Adjusting the product settings’).
Ways of preparing a The JURA F9 offers various ways of preparing a speciality coffee, milk
beverage foam or hot water:
UU Preparation using the start screen: Simply press the corre-
sponding preparation button for the product shown on the
display (start screen) that you want.
The following products are displayed as standard on the start
screen:
UU‘Espresso’
UU‘Coffee’
UU‘Flat white’
UU‘Latte macchiato’
UU Using the product selector view (Rotary Selection): Only
some of the products you can prepare are shown on the start
screen. As soon as you turn the Rotary Switch, more products
are displayed in a product selector view.
Turn the Rotary Switch to bring the product you want into
focus. Start preparation by pressing the Rotary Switch or the
‘Prepare’ button.
15
2 Preparation
The following additional products are shown in the product

selector view:
UU‘Ristretto’
UU‘2 ristretti’
UU‘2 espressi’
UU‘2 coffees’
UU‘Special’
UU‘Cappuccino’
UU‘Macchiato’
UU‘Caffè latte’
UU‘Portion milk foam’
EE The product selector view disappears automatically after
10 seconds if no preparation is started.
EE You have the option of replacing the four products on the start
screen with your personal favourites (see Chapter 4 ‘Perma-
nent settings in programming mode – Replacing products on
the start screen’). Please note that the descriptions provided
in the following sections always refer to the default settings.
Ristretto, espresso and Example: Proceed as follows to prepare one coffee.

coffee Precondition: ‘Please select product’ is displayed.
T Place a cup under the dual spout.

T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the coffee strength are dis-
played. The preset amount of water for coffee flows into the
cup.
Preparation stops automatically. ‘Please select product’
appears on the display.
Two ristretti, two espressi There are several ways of preparing two speciality coffees.
and two coffees UU Using the product selector view:
UUBring one of the double products ‘2 ristretti’, ‘2 espressi’ or
‘2 coffees’ into focus and press the Rotary Switch or the but-
ton ‘Prepare’.
UU When preparing a single product:
UUPress the single product button twice within 2 seconds to
start preparing the relevant double product.
16
2 Preparation
Example: Proceed as follows to prepare two coffees (using product

selector view).
Precondition: The start screen is displayed.
T Place two cups under the dual spout.
g T Turn the Rotary Switch to view the product selector.
g T Turn the Rotary Switch until the ‘2 coffees’ product is in
focus.
k T Press the Rotary Switch to start preparation.
Coffee preparation starts. The preset amount of water for
coffee flows into the cups. Preparation stops automatically.
Your JURA F9 is once more ready for use.
Latte macchiato, Your JURA F9 prepares latte macchiato, cappuccino, flat white and
cappuccino and other other speciality coffees with milk at the touch of a button. There is
speciality coffees with no need to move the glass or cup.
milk
Example: Proceed as follows to prepare one latte macchiato.
Precondition: ‘Please select product’ is displayed. Milk is connected
to the dual spout.
T Place a glass under the dual spout.
T Press the ‘Latte macchiato’ button.
‘Latte macchiato’, the preset amount of milk foam flows into
the glass.
EE There is a short interval while the hot milk separates from the
milk foam. This allows the typical layers of a latte macchiato
to form.
Coffee preparation starts. The preset amount of water for

espresso flows into the glass. Preparation stops automati-
cally. ‘Please select product’ appears on the display.
To ensure that the milk system in the dual spout always works prop-
erly, you must clean it daily (see Chapter 5 ‘Maintenance – Cleaning
the milk system’).
17
2 Preparation
Ground coffee You can choose to use a second coffee variety, for example decaf-
feinated coffee, with the filter funnel for ground coffee.
EE Never add more than two level measuring spoons of ground

coffee.
EE Use ground coffee which is not ground too finely. Very fine
coffee can block up the system so that the coffee only comes
out in drips.
EE If you did not fill the machine with a sufficient amount of
ground coffee, ‘Not enough ground coffee’ is displayed and
the JURA F9 stops the operation.
EE The desired speciality coffee must be prepared within approx-
imately one minute after filling with the ground coffee. Oth-
erwise the JURA F9 stops the operation and is once more ready
for use.
All speciality coffees with ground coffee are always prepared follow-
ing the same model.
Example: Proceed as follows to prepare one espresso using ground

coffee.
Precondition: ‘Please select product’ is displayed.
T Place an espresso cup under the coffee spout.
T Open the cover of the filler funnel for ground coffee.
‘Please add ground coffee’
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel.
‘Please select product’
T Press the ‘Espresso’ button.
Preparation starts. ‘Espresso’, the preset amount of water for
espresso flows into the cup.
Preparation stops automatically. ‘Please select product’
18
2 Preparation
Permanently setting the It is easy to permanently adjust the amount of water for all single
amount of water for the products to the cup size. Adjust the amount once as shown in the
cup size following example. Every time you prepare a drink in the future, this
amount will be dispensed.
Example: Proceed as follows to permanently set the amount of

water for one coffee.
T Place a cup under the dual spout.
T Press and hold the ‘Coffee’ button until ‘Enough coffee?
Press button’ appears.
T Release the ‘Coffee’ button.
Preparation starts and the coffee flows into the cup.
T Press any button as soon as there is sufficient coffee in the
cup.
Preparation stops. ‘Saved’ appears briefly on the display. The
set amount of water for one coffee is permanently stored.
‘Please select product’ appears on the display.
EE You can alter this setting at any time by repeating the above
procedure.
EE The amount can be permanently adjusted to the cup size for
the products shown in the product selector too. To do this,
press and hold the Rotary Switch k until ‘Enough coffee?
Press button’ appears.
EE You can also permanently set the amount of water for all spe-
ciality coffees and hot water in programming mode (see
Chapter 4 ‘Permanent settings in programming mode –
Adjusting the product settings’).
19
2 Preparation
Adjusting the grinder You can adjust the grinder on a continuous scale to suit the degree
of roast of your coffee.
CAUTION If you adjust the consistency of grind when the grinder is not oper-
ating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is run-
ning.
The consistency of grind is correct if the coffee flows regularly from

the coffee spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind

during the preparation of an espresso.
T Place a cup under the coffee spout.
T Open the storage compartment cover.
T Press the ‘Espresso’ button to start preparation.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The preset amount of water flows into the cup. Preparation
stops automatically.
T Close the storage compartment cover.
Hot water
J CAUTION There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.

T Place a cup under the hot-water spout.
‘Hot water’, the preset amount of water flows into the cup.
Preparation stops automatically.
‘Switch close’
20
3 Daily operation
3 Daily operation
Switching on the Daily maintenance of the machine and hygiene when handling milk,
machine coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
Precondition: Your JURA F9 is switched on at the power switch.

T Place a receptacle under the dual spout.
Q T Press the On/Off button to switch the JURA F9 on.
‘Welcome to JURA’
‘Machine is heating’
Daily maintenance To ensure that you get many years of reliable service out of your
JURA F9 and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
EE Always empty the coffee grounds container when the machine

is switched on. This is the only way of resetting the coffee
grounds counter.
T Refit the coffee grounds container and the drip tray.

T Rinse the water tank with clean water.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Dismantle and rinse the dual spout (see Chapter 5 ‘Mainte-
nance – Dismantling and rinsing the dual spout’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfibre cloth).
21
3 Daily operation
Regular maintenance Carry out the following maintenance actions regularly or as requi-
red:
UU In the interests of hygiene, we recommend changing the milk
pipe on a regular basis (approximately every 3 months).
Replacement pipes are available from specialised dealers
(JURA original accessory set for frothers).
UU Clean the inside of the water tank, e.g. with a brush. Further
information about the water tank is provided in these instruc-
tions for use (see Chapter 5 ‘Maintenance – Descaling the
water tank’).
UU Traces of milk and coffee may stick to the top and bottom of
the cup grille. If this happens, clean the cup grille.
Switching off the When the JURA F9 is switched off, the system is automatically rinsed
machine if a speciality coffee has been prepared.
Precondition: ‘Please select product’ is displayed (or ‘Rinse the milk

system’ if milk has been prepared).
Q T Press the On/Off button.
If milk has been prepared, the milk system is first rinsed
(‘Milk system is being rinsed’).
‘Machine is rinsing’, the system rinses itself. The operation
stops automatically. Your JURA F9 is switched off.
EE When the JURA F9 is switched off with the On/Off button, the
machine consumes less than 0.1 W of standby energy. The
machine can be completely disconnected from the power
supply using the power switch.
22
4 Permanent settings in programming mode
Press the P button to enter programming mode. You can navigate

through the programme items and permanently save the required
settings simply by turning the Rotary Switch and using the multi-
function buttons. The following settings can be made:
Programme item Sub-item Explanation
‘Maintenance status’ ‘Clean’, T Start the required maintenance pro-
(‘1/7’ and ‘2/7’) ‘Change the filter’ (only gramme here.
if filter is activated),
‘Descale’ (only if filter is
not activated),
‘Cappuccino cleaning’,
‘Rinse the coffee system’,
‘Rinse the milk system’
‘Product settings’ ‘Expert mode’, T Select your settings for speciality coffees
(‘3/7’) ‘Factory setting’ and hot water.
T Reset the settings for single products to
their factory setting.
‘Machine settings’ ‘Choose language’, T Select your language.
(‘4/7’) ‘Switch off after’, T Set the time after which the JURA F9
‘Save energy’, should switch off automatically.
‘Factory setting’ T Select an energy-saving mode.
T Reset the machine to its factory setting.
‘Machine settings’ ‘Units’, T Select the unit for the amount of water.
(‘5/7’) ‘Display’ T Change the display settings.
‘Maintenance settings’ ‘Use filter’, T Indicate whether you are operating your
(‘6/7’) ‘Water hardness’ (only if JURA F9 with or without a CLARIS Blue filter
filter is not activated), cartridge.
‘Switch-on rinse’ T Adjust the water hardness.
T Change the settings for switch-on rinse.
‘Information’ (‘7/7’) ‘Product counter’, T Keep track of all products prepared and
‘Maintenance counter’, view the number of maintenance pro-
‘Version’ grammes performed.
23
Product settings In the programme item ‘Product settings’ (‘3/7’) you can make the
following settings:
UU ‘Expert mode’
UUSet individual settings for all speciality coffees, milk and hot
water (see Chapter 4 ‘Permanent settings in programming
mode – Adjusting the product settings’).
UUReplace the products on the start screen with your favour-
ites (see Chapter 4 ‘Permanent settings in programming
mode – Replacing products on the start screen’).
UUChange the names of individual products (see Chapter 4
‘Permanent settings in programming mode – Renaming a
product’).
UU ‘Factory setting’
UUReset the set values for individual products to their factory
setting.
Adjusting the product In the programme item ‘Product settings’ (‘3/7’) / ‘Expert mode’ you
settings can make individual settings for all speciality coffees and hot water.
The following permanent settings can be made:
Product Coffee strength Amount More settings
Ristretto, 8 levels Amount of coffee: Temperature
Espresso, 25 ml – 240 ml (normal, high),
Coffee, Product name
Special coffee
2 ristretti, – Amount of coffee: The amount Temperature (as for
2 espressi, set for the single product is single product),
2 coffees doubled. Product name
Cappuccino, 8 levels Amount of coffee: Temperature
Latte macchiato, 25 ml – 240 ml (normal, high),
Espresso Milk foam: 0 sec. – 120 sec. Product name
macchiato, Interval: 0 sec. – 120 sec. (not
Caffè latte, for caffè latte and flat white)
Flat white
Portion of milk – Milk foam: 0 sec. – 120 sec. Product name
foam
Hot water – Water: 25 ml – 450 ml Temperature (low,
normal, high),
Product name
24
Permanent settings in programming mode always follow the same

model.
Example: Proceed as follows to change the coffee strength for one

coffee.
O T Press the P button.
‘Maintenance status’ (‘1/7’)
g T Turn the Rotary Switch until ‘Product settings’ (‘3/7’) is dis-
played.
T Press the ‘Expert mode’ button.
‘Expert mode’
EE Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
T Press the ‘ > ’ button (bottom right) until ‘Coffee’ is dis-

played.
T Press the ‘Coffee’ button.
‘Coffee’
T Press the ‘Coffee strength’ button.
‘Coffee’ / ‘Coffee strength’
g T Turn the Rotary Switch to change the coffee strength set-
ting.
‘Coffee’
O T Press the P button to exit programming mode.
Replacing products on You have the option of replacing the four products on the start
the start screen screen with your personal favourites.
Example: Proceed as follows to replace ‘Latte macchiato’ on the

start screen with ‘Macchiato’.
played.
25

‘Expert mode’
T Press the ‘ > ’ button (bottom right) several times until
‘Macchiato’ is displayed.
T Press the ‘Macchiato’ button.
‘Macchiato’
g T Press the ‘ > ’ button (bottom right) until ‘Add to favourites’
is displayed.
T Press the ‘Add to favourites’ button.
‘Select position’
T Press the ‘Latte macchiato’ button.
‘Select position’ / ‘Do you want to replace the current
product?’
T Press the ‘Yes’ button.
‘Macchiato’
Renaming a product In the programme item ‘Product settings’ / ‘Expert mode’ you can
rename all of the products.
Example: Proceed as follows to change the product name of

‘Espresso’.
played.
‘Expert mode’
T Press the ‘ > ’ button (bottom right) until ‘Espresso’ is dis-
played.
T Press the ‘Espresso’ button.
‘Espresso’
T Press the ‘ > ’ button (bottom right) until ‘Product name’ is
displayed.
26
T Press the ‘Product name’ button.

The available letters, numbers and special characters appear
on the display.
EE By pressing the ‘abc/ABC’ button, you can switch between

lower and upper case letters.
g T Turn the Rotary Switch until the letter you want is high-
lighted.
k T Press the Rotary Switch to confirm the letter.
T Continue until the new product name you want is displayed.
EE Please note that there is a maximum text length.

The new product name is displayed.
Automatic switch-off By instructing your JURA F9 to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your JURA F9 switches off automatically after the preset time follow-
ing the last action on the machine.
You can set the automatic switch-off to 15 minutes, 30 minutes or

1–9 hours.

g T Turn the Rotary Switch until ‘Machine settings’ (‘4/7’) is dis-
played.
T Press the ‘Switch off after’ button.
‘Switch off after’
g T Turn the Rotary Switch to change the switch-off time (e.g. to
‘2 hrs.’).
‘Machine settings’
27
Energy-saving mode In the programme item ‘Machine settings’ (‘4/7’) / ‘Save energy’ you
can permanently set an energy-saving mode (Energy Save Mode,
E.S.M.©):
UU ‘Active’
UUSoon after the last preparation, the JURA F9 stops heating
up. After about 5 minutes the message ‘Energy Save’ is dis-
played.
UUBefore you can prepare a speciality coffee, speciality coffee
with milk, or hot water, the machine must heat up.
UU ‘Inactive’
UUAll speciality coffees, speciality coffees with milk and hot
water can be prepared without having to wait.
Example: Proceed as follows to change the energy-saving mode

from ‘Active’ to ‘Inactive’.
played.
T Press the ‘Save energy’ button.
‘Save energy’
T Press the ‘Inactive’ button.
Maintenance settings In the programme item ‘Maintenance settings’ (‘6/7’) you can make
the following settings:
UU ‘Use filter’
UUActivate the CLARIS Blue filter cartridge (see Chapter 5
‘Maintenance – Inserting and activating the filter’).
UU ‘Water hardness’ (only if filter is not activated)
UUIf you do not have a filter cartridge, you will need to set the
water hardness (see Chapter 4 ‘Permanent settings in pro-
gramming mode – Setting the water hardness’).
28
UU ‘Switch-on rinse’
UU‘Manual’: The switch-on rinse must be started manually.
UU‘Automatic’: The switch-on rinse is started automatically.
Example: Proceed as follows to specify that the switch-on rinse
should be started manually.
g T Turn the Rotary Switch until ‘Maintenance settings’ (‘6/7’) is
displayed.
T Press the ‘Switch-on rinse’ button.
‘Switch-on rinse’
T Press the ‘Manual’ button.
‘Maintenance settings’
Setting the water EE If you are using the CLARIS Blue filter cartridge and have acti-
hardness vated it, it is not possible to set the water hardness.
The harder the water is, the more frequently the JURA F9 needs to
be descaled. It is therefore important to set the water hardness accu-
rately.
The water hardness can be adjusted on a continuous scale between

1 °dH and 30 °dH.

displayed.
T Press the ‘Water hardness’ button.
‘Water hardness’
g T Turn the Rotary Switch to adjust the water hardness.
‘Maintenance settings’
29

Display settings In the programme item ‘Machine settings’ (‘5/7’) / ‘Display’ you can
set the display brightness and contrast (as a percentage).

played.
T Press the ‘Display’ button.
‘Display’
g T Turn the Rotary Switch to change the display setting.
Unit for amount of water In the programme item ‘Machine settings’ (‘5/7’) / ‘Units’ you can
select the unit used for the amount of water.
Example: Proceed as follows to change the unit for the amount of

water from ‘ml’ to ‘oz’.
played.
T Press the ‘Units’ button.
‘Units’
T Press the ‘oz’ button.
30
Restore factory settings In the programme item ‘Machine settings’ (‘4/7’) / ‘Factory setting’
the machine can be reset to its factory setting: All user settings
(apart from the ‘filter’ and ‘water hardness’) are reset to factory set-
tings. Your JURA F9 then switches off.

played.
T Press the ‘Factory setting’ button.
‘Factory setting’ / ‘Reset the machine to the factory set-
tings?’
T Press the ‘Yes’ button.
Your JURA F9 is switched off.
Language In this programme item you can set the language used by your
JURA F9.
Example: Proceed as follows to change the language from ‘English’

to ‘Deutsch’.
played.
T Press the ‘Choose language’ button.
‘Choose language’
EE To display more languages, press the ‘ > ’ button (bottom

right).
T Press the ‘Deutsch’ button.

‘Gespeichert’ appears briefly on the display.
‘Geräteeinstellungen’
‘Bitte wählen’
31
Querying information In the programme item ‘Information’ (‘7/7’) you can view the follow-
ing information:
UU ‘Product counter’: Number of prepared speciality coffees,
speciality coffees with milk and hot water
UU ‘Maintenance counter’: Number of maintenance programmes
performed (cleaning, descaling etc.)
UU ‘Version’: Software version
Example: Proceed as follows to view the number of speciality cof-

fees prepared.
g T Turn the Rotary Switch until ‘Information’ (‘7/7’) is displayed.
T Press the ‘Product counter’ button.
‘Product counter’
EE Press the ‘ > ’ button (bottom right) to display the number of

additional speciality coffees.

32
5 Maintenance
5 Maintenance
Your JURA F9 has the following integrated maintenance pro-

grammes:
UU Rinsing the machine (‘Rinse the coffee system’)
UU Rinsing the milk system in the dual spout
(‘Rinse the milk system’)
UU Cleaning the milk system in the dual spout (‘Cappuccino
cleaning’)
UU Changing the filter (‘Change the filter’) (only if filter is acti-
vated)
UU Cleaning the machine (‘Clean’)
UU Descaling the machine (‘Descale’) (only if filter is not acti-
vated)
EE Clean or descale the machine, rinse the milk system or change

the filter when you are prompted to do so.
EE Press the P button to view a list of the maintenance pro-
grammes (‘Maintenance status’). By referring to the bar you
can see which maintenance programme is due. When the bar
is completely filled with red, your JURA F9 will prompt you to
perform the appropriate maintenance programme.
EE In the interests of hygiene, you should clean the milk system
daily when you have been preparing milk.
Rinsing the machine You can initiate the rinse operation manually at any time.

g T Turn the Rotary Switch until ‘Maintenance status’ (‘2/7’) is
displayed.
T Press the ‘Rinse the coffee system’ button to initiate the
rinse operation.
‘Machine is rinsing’, water flows out of the dual spout.
The rinse stops automatically. ‘Please select product’
33
5 Maintenance
Rinsing the milk system After each milk preparation, the JURA F9 prompts you to perform a
milk system rinsing.
Precondition: ‘Rinse the milk system’ is displayed.

k T Press the Rotary Switch.
‘Milk system is being rinsed’, water flows out of the dual
spout.
The rinse stops automatically. Your JURA F9 is once more
ready for use.
Cleaning the milk system To ensure that the milk system in the dual spout always works prop-
erly, you must clean it daily when you have been preparing milk.
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EE JURA milk system cleaner is available from specialised dealers.

T Press the ‘Cappuccino cleaning’ button.
T Press the ‘Start’ button.
T Press the ‘Start’ button again.
‘Cleaner for Cappuccino’
T Remove the milk pipe from the milk container or carton.
T Pour 250 ml of fresh water into a receptacle and add one
capful of milk system cleaner.
T Immerse the milk pipe in the receptacle.
T Place another receptacle under the dual spout.
‘Cleaning Cappuccino’, the dual spout and the pipe are
cleaned.
‘Water for Cappuccino’
T Rinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
34
5 Maintenance
T Empty the other receptacle and place it under the dual spout
again.
‘Cleaning Cappuccino’, the dual spout and the pipe are
rinsed with fresh water.
The operation stops automatically. ‘Milk system cleaning
complete’ appears briefly on the display.
Your JURA F9 is once more ready for use.
Dismantling and rinsing The dual spout must be dismantled and rinsed daily if milk has been
the dual spout prepared to make sure it functions perfectly and also in the interests
of hygiene.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Press the releasing devices and pull the dual spout down and
off.
T Press the milk system down and take it out.
35
5 Maintenance
T Dismantle the milk system into its individual parts.

T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250 ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
T Fit the air intake pipe.
T Reassemble the milk system. When doing this, note the

numbering of the individual parts.
1 T Fit the assembled individual parts back in the dual spout and
2 press it firmly.
T Fit the dual spout on the machine. It will click into place audi-
bly.
Inserting and activating Your JURA F9 no longer has to be descaled if you are using the
the filter CLARIS Blue filter cartridge. If you did not activate the filter cartridge
the first time you used the machine, you can do this now as follows.
EE Perform the ‘inserting the filter’ operation without any inter-

ruptions. This will ensure that your JURA F9 always produces
its best.

36
5 Maintenance

displayed.
T Press the ‘Use filter’ button.
‘Use filter’
T Press the ‘Active’ button.
‘Insert filter’
T Remove and empty the water tank.
T Open the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
tank.
‘Switch open’
T Place a receptacle under the hot-water spout.
spout.


‘Please select product’ appears on the display. The filter is
now activated.
Changing the filter EE After 50 litres of water have flowed through, the filter will
cease to work. Your JURA F9 will automatically prompt you to
change the filter.
37
5 Maintenance
EE If the CLARIS Blue filter cartridge is not activated in program-
ming mode, you will not be prompted to change the filter.
EE CLARIS filter cartridges are available from specialised dealers.
Precondition: ‘Change the filter’ is displayed.

T Press the ‘Change the filter’ button.
‘Change the filter’
‘Change filter’
T Open the filter holder and remove the old CLARIS Blue filter
cartridge.
T Insert a new CLARIS filter cartridge Blue into the water tank,
exerting slight pressure.
tank.

‘Switch open’
spout.


38
5 Maintenance
Cleaning the machine After 200 preparations or 80 switch-on rinses, the JURA F9 will
prompt you to clean it.
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
EE The cleaning programme lasts approximately 20 minutes.

EE Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EE JURA cleaning tablets are available from specialised dealers.
Precondition: ‘Clean machine’ is displayed.

T Press the ‘Clean’ button.
‘Clean’
‘Empty grounds’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Press the Rotary Switch’
‘Machine is being cleaned’, water flows out of the dual spout.
The operation is interrupted, ‘Add cleaning tablet’.
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.

T Close the cover of the filler funnel.
‘Press the Rotary Switch’
‘Machine is being cleaned’, water flows out of the dual spout
repeatedly.
The operation stops automatically.
‘Empty grounds’
39
5 Maintenance
‘Please select product’ appears on the display. Cleaning is
now complete.
Descaling the machine The JURA F9 builds up deposits of limescale over time and automat-
ically prompts you to descale it when necessary. The degree of cal-
cification depends on the hardness of your water.
EE If you use a CLARIS Blue filter cartridge and this is activated,

you will not be prompted to descale.
J CAUTION If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
CAUTION If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
CAUTION If the descaling operation is interrupted, there may be damage to

the machine.
T Allow the descaling programme to run to the end.
CAUTION If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
EE The descaling programme lasts approximately 40 minutes.

EE JURA descaling tablets are available from specialised dealers.
Precondition: ‘Decalcify machine’ is displayed.

T Press the ‘Descale’ button.
‘Descale’
‘Empty drip tray’
40
5 Maintenance
‘Agent in tank’
T Completely dissolve the contents of one blister (3 JURA des-
caling tablets) in a receptacle holding 500 ml of lukewarm
water. This may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
‘Switch open’

‘Machine is being descaled’, water flows out of the hot-water
spout repeatedly.
The operation is interrupted, ‘Switch close’.
‘Machine is being descaled’, the descaling operation is con-
tinued. Water flows out of the dual spout repeatedly.
The operation is interrupted, ‘Empty drip tray’.
T Empty the receptacle and place it under the hot water and
dual spouts.
T Remove the water tank and rinse it thoroughly.
tank.
‘Switch open’
tinued.
The operation is interrupted, ‘Switch close’.
tinued.
The operation is interrupted, ‘Machine is being descaled’.
Water flows out of the dual spout.
‘Empty drip tray’
41
5 Maintenance
‘Please select product’ appears on the display. Descaling is
now complete.
EE If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.
Descaling the water tank Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLARIS Blue filter cartridge, remove this.
T Completely fill the water tank and dissolve 3 JURA descaling
tablets in it.
T Leave the water tank with the descaling solution for several
hours (e.g. overnight).
T Empty the water tank and rinse it thoroughly.
T If you use a CLARIS Blue filter cartridge, insert this again.
tank.
Cleaning the bean Coffee beans may be covered with a slight oil film which remains on
container the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition: ‘Fill bean container’ is displayed.

Q T Switch the machine off with the On/Off button.
3 T Switch the machine off at the power switch.
T Remove the aroma preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
42
6 Display messages
6 Display messages
Message Cause/Result Action

‘Fill water tank.’ The water tank is empty. You T Fill the water tank (see Chapter 1
cannot prepare any products. ‘Preparing and using for the first time –
Filling the water tank’).
‘Empty grounds’ The coffee grounds container is T Empty the coffee grounds container
full. You cannot prepare any and the drip tray (see Chapter 3 ‘Daily
products. operation – Daily maintenance’).
‘Drip tray not The drip tray is not inserted T Fit the drip tray.
fitted’ correctly or is not inserted at all.
You cannot prepare any products.
‘Fill bean The bean container is empty. You T Fill the bean container (see Chapter 1
container’ cannot prepare any products. ‘Preparing and using for the first time –
Filling the bean container’).
‘Rinse the milk The JURA F9 requests a milk T Perform milk system rinsing (see
system’ system rinsing. Chapter 5 ‘Maintenance – Rinsing the
milk system’).
‘Change the filter’ The filter cartridge no longer T Replace the CLARIS Blue filter cartridge
works. (see Chapter 5 ‘Maintenance –
Changing the filter’).
‘Clean machine’ The JURA F9 is prompting you to T Perform cleaning (see Chapter 5
clean it. ‘Maintenance – Cleaning the machine’).
‘Decalcify The JURA F9 is prompting you to T Perform descaling (see Chapter 5
machine’ descale it. ‘Maintenance – Descaling the machine ’).
‘Not enough There is insufficient ground T The next time you prepare a beverage,
ground coffee’ coffee in the machine; the JURA add more ground coffee (see Chapter 2
F9 stops the operation. ‘Preparation – Ground coffee’).
‘Too hot’ The system is too hot to start a T Wait for several minutes until the
maintenance programme. system has cooled or prepare a special-
ity coffee or hot water.
43
7 Troubleshooting
7 Troubleshooting
Problem Cause/Result Action

Insufficient foam is The dual spout is dirty. T Clean the milk system in the dual spout
produced when the (see Chapter 5 ‘Maintenance – Cleaning
milk is frothed, or milk the milk system’).
sprays from the dual T Dismantle and rinse the dual spout (see
spout. Chapter 5 ‘Maintenance – Dismantling
and rinsing the dual spout’).
Coffee only comes out Coffee or ground coffee has T Put the grinder on a coarser setting or
in drips when it is been ground too finely and use coarser ground coffee (see Chapter 2
being prepared. is blocking the system. The ‘Preparation – Adjusting the grinder’).
same filter cartridge may T Perform descaling (see Chapter 5
have been used several ‘Maintenance – Descaling the machine ’).
times or the water hardness
set incorrectly in the
programming mode.
Water hardness cannot The CLARIS Blue filter T Deactivate the filter cartridge in
be adjusted. cartridge is activated. programming mode.
‘Fill water tank.’ is The water tank float is T Descale the water tank (see Chapter 5
displayed although the trapped. ‘Maintenance – Descaling the water
water tank is full. tank’).
Grinder is making a There are foreign objects in T Contact customer support in your
very loud noise. the grinder. country (see Chapter 11 ‘JURA contact
details / Legal information’).
‘Error 2’ or ‘Error 5’ is If the machine was exposed T Warm the machine at room tempera-
displayed. to the cold for a long period ture.
of time, heating is disabled
for safety reasons.
Other ‘Error’ messages – T Switch the JURA F9 off at the power
are displayed. switch. Contact customer support in
your country (see Chapter 11 ‘JURA
contact details / Legal information’).
EE If you were unable to solve the problem, contact customer

support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
44
8 Transport and environmentally friendly disposal
8 Transport and environmentally friendly disposal
Transport / Emptying the Keep the packaging for your JURA F9. It should be used to protect
system the machine during transport.
In order to protect the JURA F9 from frost during transport, the sys-
tem must be emptied.

T Remove the milk pipe from the dual spout.
g T Turn the Rotary Switch to view the product selector.
g T Turn the Rotary Switch until the ‘Portion milk foam’ product
is in focus.
‘Portion milk foam’, hot steam is discharged from the dual
spout.
T Turn the Rotary Switch until ‘Amount of milk’ ‘60 sec.’ is dis-
played.
Steam will continue to be discharged from the dual spout
until the system is empty.
Q T Press the On/Off button.
Your JURA F9 is switched off.
Disposal Please dispose of old machines in an environmentally neutral way.

H
Old machines contain valuable, recyclable materials which should
be recycled. Please therefore dispose of old machines via suitable
collection systems.
45
9 Technical data
9 Technical data
Voltage 220–240 V ~, 50 Hz
Power 1450 W
Conformity mark A
Energy consumption approx. 5 Wh
‘Save energy’ / ‘Active’
Energy consumption approx. 16 Wh
‘Save energy’ / ‘Inactive’
Pump pressure static, max. 15 bar
Holding capacity of water tank 1.9 l
Holding capacity of bean container 310 g
Holding capacity of coffee grounds max. 15 portions
container
Cable length approx. 1.1 m
Weight approx. 9.8 kg
Dimensions (W × H × D) 28.5 × 35.5 × 44.5 cm
Information for testers (repeat test in accordance with DIN VDE

0701-0702): The central grounding point (CGP) is located on the
underside of the machine, right next to the mains cable's connec-
tion point.
46
10 Index
10 Index
A Cover
Addresses 52 Filler funnel for ground coffee 4
Adjusting the product settings 24 Storage compartment 4
Aroma preservation cover Water tank 4
Bean container with aroma preservation Cup grille 4
cover 4 Customer support 52
Automatic switch-off 27 D
B Descaling
Bean container Machine 40
Bean container with aroma preservation Water tank 42
cover 4 Display 5
Cleaning 42 Display messages 43
Filling 10 Display settings 30
Bus bar Disposal 45
Technical data 46 Double product 16
Button Drip tray 4
Dual spout
On/Off button 5
Dismantling and cleaning 35
P button (programming) 5
Height-adjustable dual spout 4
C
Caffè latte 17 E
Cappuccino 17 Emptying the system 45
Cappuccino frother cleaning Energy-saving mode 28
Errors
Cleaning the milk system 34
Cappuccino frother rinsing Troubleshooting 44
Espresso
Rinsing the milk system 34
Central grounding point 46 2 espressi 16
Changing a name 26 Espresso 16
CLARIS Blue filter cartridge Espresso macchiato 17
Expert mode 24
Changing 37
Inserting and activating the filter 36 F
Classics 24 Factory settings
Cleaning Restore factory settings 31
Bean container 42 Filler funnel
Machine 39 Filler funnel for ground coffee 4
Coffee 16 Filling
2 coffees 16 Bean container 10
Coffee grounds container 4 Water tank 14
Consistency of grind Filter
Adjusting the grinder 20 Changing 37
Grinder adjustment switch 4 Inserting and activating the filter 36
Contact details 52 First-time use 10
With filter cartridge activation 11
Without filter cartridge activation 12
Flat white 17
47
10 Index
G P
Grinder adjustment switch 4 Permanently setting the water for the cup
Ground coffee 18 size 19
Measuring spoon for ground coffee 4 Permanent settings in programming mode
Grounding point 46 23
Power switch 4
H Preparation 15, 17
Hotline 52 2 coffees 16
Hot water 20
2 espressi 16
Hot water preparation
2 ristretti 16
Switch for hot water preparation 5
Hot-water spout 4 At the touch of a button 15
Caffè latte 17
I Cappuccino 17
Instant coffee Coffee 16
Ground coffee 18 Espresso 16
Internet 10 Espresso macchiato 17
J Flat white 17
JURA Ground coffee 18
Contact details 52 Hot water 20
Internet 10 Latte macchiato 17
Ristretto 16
L Two speciality coffees 16
Language 31
Using the product selector 15
latte macchiato 17
Preparation options 15
M Problems
Machine Troubleshooting 44
Cleaning 39 Product selector view 15
Descaling 40 Product settings 24
Regular maintenance 22 Adjusting 24
Rinsing 33 Programming mode 23
Setting up 10 Automatic switch-off 27
Switching off 22 Display settings 30
Switching on 21 Energy-saving mode 28
Mains cable 4 Language 31
Maintenance 33 Maintenance settings 28
Daily maintenance 21 Product settings 24
Regular maintenance 22 Querying information 32
Maintenance settings 28 Renaming a product 26
Measuring spoon for ground coffee 4 Replacing products on the start screen 25
Messages, display 43 Restore factory settings 31
Milk Setting the water hardness 29
Connecting milk 14 Unit for amount of water 30
Milk system Proper use 6
Cleaning 34
Rinsing 34 Q
Querying information 32
48
10 Index
R
Regular maintenance 22
Renaming a product 26
Rinsing
Machine 33
Ristretto 16
2 ristretti 16
Rotary Selection 15
Rotary Switch 5
S
Safety 6
Safety information 6
Settings
Maintenance settings 28
Permanent settings in programming
mode 23
Setting up
Setting up the machine 10
Short operating instructions 10
Spout
Height-adjustable dual spout 4
Hot-water spout 4
Switch for hot water preparation 5
Switching off 22
Switching on 21
Switch-off
Automatic switch-off 27
Symbol description 3
T
Technical data 46
Tel 52
Transport 45
Troubleshooting 44
Two products 16
U
Unit for amount of water 30
Use, First-time 10
W
Water hardness
Determining the water hardness 13
Setting the water hardness 29
Water tank 4
Descaling 42
Filling 14
Website 10
49
50
51
J71806/F9/en/201407
11 JURA contact details / Legal information
11 JURA contact details / Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 (0)62 38 98 233
@@ You will find additional contact details for your country at

www.jura.com.
Directives The machine complies with the following directives:

UU2006/95/EC – Low Voltage Directive
UU2004/108/EC – Electromagnetic Compatibility
UU2009/125/EC – Ecodesign Directive
UU2011/65/EU – RoHS Directive
Technical changes We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine. Some details of
your JURA F9 may vary.
Feedback Your opinion is important to us! Use the contact details at

www.jura.com.
Copyright The instructions for use contain information which is protected by

copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
52

Jura F9 User Manual

Uploaded by

Copyright:

Available Formats

Jura F9 User Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jura F9 User Manual

Uploaded by

Copyright:

Available Formats

JURA F9 Instructions for Use

1 Bean container with aroma preservation 8 Filler funnel cover

Top of the machine Front

UU Never open and repair the machine yourself.

UU Only connect the machine to the mains volt-

People, including children, who

1 Preparing and using for the first time

Filling the bean container

T Remove the aroma preservation cover.

J WARNING If the machine is operated with a defective mains cable, there is a

Precondition: The bean container has been filled.

EE To display more languages, press the ‘ > ’ button (bottom

T Press the button that corresponds to the language you want,

EE Now decide whether you want to operate your JURA F9 with

First-time use with filter

T Press the ‘Active’ button.

EE You can interrupt rinsing of the filter at any time. To do this,

Rinsing of the filter stops automatically after approximately

EE The display shows the products you can prepare.

First-time use without filter

T Press the ‘Inactive’ button.

g T Turn the Rotary Switch to change the water hardness set-

T Place a receptacle under the hot-water spout and dual spout.

EE The display shows the products you can prepare.

T Connect the milk pipe to the dual spout.

T Open the water tank cover.

You can make permanent settings for all products in programming

The following additional products are shown in the product

Ristretto, espresso and Example: Proceed as follows to prepare one coffee.

T Place a cup under the dual spout.

Example: Proceed as follows to prepare two coffees (using product

Coffee preparation starts. The preset amount of water for

EE Never add more than two level measuring spoons of ground

Example: Proceed as follows to prepare one espresso using ground

Example: Proceed as follows to permanently set the amount of

The consistency of grind is correct if the coffee flows regularly from

Example: Proceed as follows to change the consistency of grind

Precondition: ‘Please select product’ is displayed.

Precondition: Your JURA F9 is switched on at the power switch.

EE Always empty the coffee grounds container when the machine

T Refit the coffee grounds container and the drip tray.

Precondition: ‘Please select product’ is displayed (or ‘Rinse the milk

4 Permanent settings in programming mode

Press the P button to enter programming mode. You can navigate

Permanent settings in programming mode always follow the same

Example: Proceed as follows to change the coffee strength for one

T Press the ‘ > ’ button (bottom right) until ‘Coffee’ is dis-

Example: Proceed as follows to replace ‘Latte macchiato’ on the

T Press the ‘Expert mode’ button.

Example: Proceed as follows to change the product name of

T Press the ‘Product name’ button.

EE By pressing the ‘abc/ABC’ button, you can switch between

EE Please note that there is a maximum text length.

T Press the ‘Save’ button.

You can set the automatic switch-off to 15 minutes, 30 minutes or

Precondition: ‘Please select product’ is displayed.

Example: Proceed as follows to change the energy-saving mode

The water hardness can be adjusted on a continuous scale between

Precondition: ‘Please select product’ is displayed.