Torq-Matic Canrig Sec-08 Part List

MODEL TM120 TORQ-MATIC FLOOR WRENCH
SECTION 8: PARTS
CANDOC TM120 MANUAL COPYRIGHT © 2004 CANRIG DRILLING TECHNOLOGY LTD.

S/N TM120-069 MANUAL_01 ALL RIGHTS RESERVED
Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the express written permission of Canrig Drilling Technology Ltd.
Printed in the United States of America

SUBSECTION 8: FLOOR WRENCH
Assembly Description Drawing Rev
102200003 ASSY, WRENCH, TM-120 SERIES, ARM, LONG 102200003 DEV-11

112100001 TM120 TORQUE ASSY 112100001 DEV-17
112200003 SPINNER ASSY 112200003 DEV-04
112300002 PIVOT ARM ASSY 112300002 A
122100003 JAW ASSEMBLY 122100003 DEV-05
122100004 POWER PACK, HYD, 480 VAC 122100004 REL-04
122100007 TONG ASSEMBLY 122100007 DEV-05
122200006 SPINNER TRACK JEEP, TM-120 122200006 DEV-06
122200007 SPINNER TRACK V MOUNT 122200007 DEV-03
122200008 SPINNER JEEP CARRIAGE 122200008 DEV-05
122200010 BULKHEAD MOUNT ASSEMBLY 122200010 DEV-03
122200012 ROLLER FRAME 122200012 DEV-08
122200013 SPINNER ROLLER 122200013 DEV-06
122300009 ASSEMBLY, VERTICAL LIFT, WRENCH ARM 122300009 A
122300011 WRENCH ARM PIVOT ASSY, TM-80/120 122300011 DEV-13
183200001 PLUMBING LAYOUT, TM120 183200001 D
AY50130 TM80/120, ARM CONTROL VLV AY50130 A
AY50131 TM-120 LIFTING CHAIN AY50131 REL-03
AY50137 ASSY, ELEC, TM120, ARM NO DRAWING 0
AY50145 ASSY, ELEC, MAIN PANEL BOX, WRENCH AY50145 REL-03
AY50146 ASSY, ELEC, DRILLERS CONSOLE, WRENCH AY50146 REL-02
AY50147 ASSY, ELEC, HPU, STARTER PANEL, 480V AY50147 REL-02
AY50148 ASSY, ELEC, ARM BOX, WRENCH AY50148 REL-02
AY50149 ASSY, ELEC, TONG BOX, TM120 AY50149 REL-01

AY50155 RADIO CONTROL UNIT, WRENCH, WIRELESS NO DRAWING 0
AY50224 TM120, TONG CONTROL VLV AY50224 REL-02
AY50248 HOSE ASSY, POWER UNIT SUPPLY & RET NO DRAWING 0
AY50275 HOSE ASSY, WRENCH ARM NO DRAWING 0
AY50276 HOSE ASSY, TONG VLV TO ELEC BOX NO DRAWING 0
AY50277 HOSE ASSY, TONG VLV TO TONGS, BLKHD NO DRAWING 0
Thursday, July 10, 2008 Serial Number TM80-069

AY50278 HOSE ASSY, PRESS & TANK TO TONG VLV NO DRAWING 0
AY50279 HOSE ASSY, TONG VLV TO SPINNER BLKHD NO DRAWING 0
AY50280 HOSE ASSY, BLKHD TO SPINNER NO DRAWING 0
AY50281 HOSE ASSY, PIVOT BEARINGS NO DRAWING 0
AY50282 HOSE ASSY, QUICK COUPLERS NO DRAWING 0
AY50283 HOSE ASSY, UPPER TONG PLUMBING NO DRAWING 0
AY50284 HOSE ASSY, LOWER TONG PLUMBING NO DRAWING 0
AY50285 HOSE ASSY, PURGE HOSES NO DRAWING 0
AY50286 HOSE ASSY, LIFT CYL HOSES NO DRAWING 0
AY50430 KIT, LABEL, ENG, ARM, TM120 AY50430 A
AY50472 VLV SECTION, JAW CLAMPS, TM-120 AY50472 DEV-02
AY50473 VLV SECTION, TONG TORQUE CYL, TM-120 AY50473 DEV-02
AY50474 VLV SECTION, SPINNER MOTOR, TM-120 AY50474 DEV-02
AY50475 VLV SECTION, SPINNER CLAMP CYL, TM-120 AY50475 REL-03
AY50479 VLV, INLET COMPLETE, 5 SERIES, TM-120 AY50479 REL-02
AY50501 SUBPLATE, INLET, 5 SERIES AY50501 DEV-01
AY50503 SUBPLATE, VLV ASSY, 5/5 AY50503 DEV-01
AY50506 VLV, ARM CONTROL, WRENCH, 3 SERIES AY50506 DEV-01
AY50507 VLV SECTION, ROTATE CONTROL, WRENCH AY50507 DEV-01
AY50508 VLV SECTION, VERT CONTROL, WRENCH AY50508 DEV-01
AY50509 VLV SECTION, HOR CONTROL, WRENCH AY50509 DEV-01
AY50510 VLV INLET, WRENCH ARM, 3 SERIES AY50510 DEV-01
AY50517 SENSOR, LINEAR DISPLACEMENT, 450 STRK AY50517 A

Engineering
Bill of Material
Part: 102200003
Description: ASSY, WRENCH, TM-120 SERIES, ARM, LONG
Eng ID: 4
Drawing ID: 102200003 Rev No: DEV-11
Item Qty Units Part ID Description
01 1.00 EA 112100001 TM120 TORQUE ASSY

02 1.00 EA 112200003 SPINNER ASSEMBLY
03 1.00 EA 112300002 PIVOT ARM ASSY
04 1.00 EA 112300003 SHIPPING SKID (VERTICAL)
05 1.00 EA 122200006 SPINNER TRACK JEEP, TM-120
06 1.00 EA 131100126 WELDMENT, JEEP MOUNT
07 0.00 EA 131100398 POCKET, INSTALLATION, TM WRENCH, ARM
08 2.00 EA 161100393 HITCH PIN
09 1.00 EA AY50131 TM-120 LIFTING CHAIN
10 2.00 EA M24-5003-010 PIN, LYNCH, SAFETY TYPE, 5/16 DIA
11 5.00 EA HH-0500NC-0125-GR8 CAPSCR, HEX HD, 1/2-13UNC x 1.25, GR8
14 8.00 EA FW-0500-A WASHER, F, 1/2, PLAIN, TYPE A
15 8.00 EA LW-0500-HS LOCKWASHER, 1/2, HELICAL SPRING
16 2.00 EA M10924 RATCHET STRAP, 3 IN DOUBLE J-HOOK
17 1.00 EA 181200001 SCHEMATIC, HYD, TM120
18 1.00 EA 183200001 PLUMBING LAYOUT, TM120
19 1.00 EA AY50430 KIT, LABEL, ENG, ARM, TM120
20 80.00 FT M10870 WRAP, HOSE GUARD, ID 1.5, 1.000 PITCH
Printed: 7/11/2008
3
2
14 15 11
5
6
13
7 14 15 12
1
10
16
16
TRANSPORTATION
NOTICE
THE DRAWINGS, INFORMATION AND SUBJECT MATTER
REV. DESCRIPTION DATE •PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE WRENCH ARM ASSEMBLY
•FAX: (403) 233-2667 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
DEV-11 ADDED TRANSPORT TIEDOWN STRAPS 12/20/2007
•WEBSITE: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
IN ANY MANNER FOR ANY PURPOSE WHATSOEVER
1 OF 1
DEV-10 UPDATED BOM ASBUILT 12/12/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-09 UPDATED REVISION LEVELS AND VIEWS 10/31/2007 CREATED: January 12, 2007 10:41:30 AM PART NO: 102200003 REV. DEV-11
Engineering
Bill of Material
Part: 112100001
Description: TM120 TORQUE ASSY
Eng ID: 4
01 4.00 EA 122100003 JAW ASSEMBLY

02 1.00 EA 122100007 TONG ASSEMBLY
03 1.00 EA 131100177 WELDMENT, VALVE MOUNT
04 0.00 EA AY50149 TONG ELECTRICAL BOX
05 1.00 EA AY50224 TONG CONTROL VALVE
06 3.00 EA 158100028 ELL 45, MALE 3/4 JIC, MALE 3/4 ORB
07 1.00 EA 158100029 ADPT, MALE 3/4 JIC, MALE 3/4 ORB
08 4.00 EA 158100030 PLUG, HOLLOW HEX PIPE, 3/8 NPT
09 4.00 EA 161100127 JAW RAM PIN
10 1.00 EA 161100029 TORQUE PLATE RAM PIN
11 1.00 EA 161100138 RAM PIN
12 1.00 EA AY50517 SENSOR, LINEAR DISPLACEMENT, 450 STRK
13 2.00 EA E12540 SPACER, 1/2 x .049W TUBE
14 1.00 EA H10338 CYL, HYD, BORE 4, ROD 2, STRK 15
15 2.00 EA H15-070220-12 ELL 90°, MALE 3/4 JIC, MALE 3/4 ORB
16 2.00 EA H15-070320-12-12 ELL 45°, MALE 3/4 JIC, MALE 3/4 ORB
17 2.00 EA H15-070320-12-16 ELL 45°, MALE 3/4 JIC, MALE 1 ORB
18 2.00 EA H15-070603-04-02 ADPT, MALE 1/4 JIC, FEM 1/8 NPT
19 2.00 EA H15-070701-12-12 ELL 90°, BULKHEAD, MALE 3/4 JIC
20 4.00 EA H15-070959-12-12 TEE, BULKHEAD BRANCH, MALE 3/4 JIC
21 4.00 EA H15-080118-12 BULKHEAD, NUT, 3/4
22 2.00 EA H15-080118-02 BULKHEAD, NUT, 1/8
23 4.00 EA M10533 FTG, GREASE, 1/8 NPT, PTF-SS
26 3.00 EA HH-10MM-20MM-GR8 CAPSCR, HEX HD, M10 x 20, GR8
27 2.00 EA SB-0375-0100NC SCR, SHLDR, 5/16-18NC x 1.00, GR8
28 2.00 EA SS-0375NC-0050 SETSCREW 3/8-16UNC x 0.50 CUP POINT
31 4.00 EA LW-0250-HS LOCKWASHER, 1/4 HELICAL SPRING
Printed: 7/11/2008
1 16 15
6
2
9
8 29
8 6
15
7
16
2 8
1
10
28
14
23
20
17 11
18 22
23
12
13
4 5
27
24
3
31
26 25 32
30
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TM120 TORQUE ASSEMBLY
REV. DESCRIPTION DATE •FAX: (403) 233-2667 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
DEV-17 ADDED MODIFIED FITTINGS AND MODIFIED PLUG TO ROD END OF JAW CYLINDERS 2/13/2008 •WEBSITE: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
1 OF 2
WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-16 UDPATED BOM TO AS BUILT 12/12/2007
DEV-15 ADDED MOUNTING HARDWARE UPDATED FITTINGS 10/26/2007 CREATED: January 11, 2007 1:28:14 PM PART NO: 112100001 REV. DEV-17
B GREASE
POINT
CYLINDER
GREASE
POINTS
TYP
SECTION A-A DETAIL B

TYP TONG INTERFACE
20 20
TONG GREASE
HOSE CONNECTIONS
SECTION C-C
C A A C
CYLINDER
GREASE
POINTS
TYP
JAW POCKET
GREASE
POINTS TYP.
CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TM120 TORQUE ASSEMBLY
Calgary, Alberta, Canada, T2C 4L6 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
Website: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
Bus. (403) 237-6400
Fax. (403) 233-2667
IN ANY MANNER FOR ANY PURPOSE WHATSOEVER SHEET 2 OF 2
DATE CREATED: PART NO: REV:
January 11, 2007 1:28:14 PM 112100001 DEV-17
Engineering
Bill of Material
Part: 112200003
Description: SPINNER ASSY
Eng ID: 0
01 1.00 EA 122200010 BULKHEAD MOUNT ASSEMBLY

02 2.00 EA 122200013 SPINNER ROLLER
03 1.00 EA 131100179 SPINNER ARM MOUNT LEFT
04 1.00 EA 131100180 SPINNER ARM RIGHT
05 1.00 EA 131100292 TRAVELING FRAME
06 2.00 EA 141100393 PLATE, ALIGNMENT BAR
07 8.00 EA 141100394 PLATE, WASHER
08 4.00 EA 161100111 SPINNER PIVOT PIN
09 2.00 EA 161100112 SPINNER RAM PIN
10 2.00 EA 161100120 ALIGNMENT BAR PIN
11 2.00 EA 161100388 PIN, ALIGNMENT BAR, TRAVELING FRAME
12 1.00 EA H10339 CYL, HYD, 5 BORE, 2 ROD, 7 1/2 STRK
13 8.00 EA M10528 CAM FOLLOWER, 2.00IN OD, ECCENTRIC STUD
14 4.00 EA M10907 BUSHING
15 4.00 EA M10601 BUSH, 1.5 B x 1.75 OD x 1 WIDTH
19 2.00 EA SS-0375NC-0063 SETSCREW, 3/8-16UNC X 0.625, CUP POINT
24 8.00 EA LN-0875NF-GR8 LOCKNUT, 7/8-18UNF, GR8, STOVER
25 6.00 EA LN-0750NC-GR8 LOCKNUT, 3/4-10UNC, GR8, STOVER
26 1.00 EA H15-070120-08-08 ADAPTER, MALE 1/2 JIC, MALE 1/2 ORB
27 2.00 EA H15-070120-08-10 ADPT, MALE 1/2 JIC, MALE 5/8 ORB
28 3.00 EA H15-070120-12-16 ADPT, MALE 3/4 JIC, MALE 1 ORB
30 1.00 EA H15-070220-12-16 ELL 90°, MALE 3/4 JIC, MALE 1 ORB
31 4.00 EA M11128 QUICK LINK, THREADED CONNECTOR, 3/8"
32 2.00 EA M11129 EYEBOLT, SHLD TYPE, 1/2-13UNC x 1-1/4
33 2.00 FT M11131 STRAIGHT LINK, CHAIN, 3/8IN DIA
35 2.00 EA HN-0500NC-GR8 HEX NUT, 1/2-13UNC, GR8
Printed: 7/11/2008
16
8
1 17 21
7
15
9
12
16
26
35 21
34 34 34
3 32 31 33 13 23 24
2 18 16 29
16
8 19 22 25 18
7
4
28 30
6
10
11
14
6
27
20
16 22
25

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SPINNER ASSEMBLY, BEARINGS
Bus. (403) 237-6400
Fax. (403) 233-2667
REV. DESCRIPTION DATE WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-04 FIXED ASSEMBLY AND BOM, ADDED HYD FITTINGS 10/23/2007 DATE CREATED: PART NO: REV:
DEV-03 ISSUED FOR MANUALS 24/05/2007 January 08, 2007 10:35:43 AM 112200003 DEV-04
Engineering
Bill of Material
87 32.00 EA FH-0375NC-0150 CAPSCREW, FLAT HD, 3/8UNC x 1.50
95 3.00 EA HN-0375NC-GR8 HEX NUT, 3/8-16UNC GR8
97 2.00 EA LN-0312NC-NL-GR8 LOCKNUT, 5/16-18UNC, NYLOCK, GR8
Printed: 7/11/2008
Engineering
Bill of Material
41 1.00 EA H10587 CAP, DUST, QUICK CONN 1 1/4IN, BRASS
42 1.00 EA H10603 PLUG, DUST, QUICK CON, HP-1001 COUPLER
43 1.00 EA H10604 CAP, DUST, QUICK CONNECT,1 IN, HP SER
44 2.00 EA H15-0506-08-08 ADAPTER, FEM SWV 1/2 JIC, 1/2 MALE ORB
46 3.00 EA H15-070120-08-08 ADAPTER, MALE 1/2 JIC, MALE 1/2 ORB
48 2.00 EA H15-070120-16-20 ADPT, MALE 1 JIC, MALE 1-1/4 ORB
49 2.00 EA H15-070123-08-04 REDUCER, FEMALE 1/2 JIC, MALE 1/4 JIC
50 2.00 EA H15-070123-16-08 REDUCER, FEMALE 1JIC, MALE 1/2 JIC
53 1.00 EA H15-070401-08 TEE, UNION, 1/2 JIC MALE
54 2.00 EA H15-070432-08-08 TEE, FEM SWV RUN 1/2, MALE 1/2 JIC
55 1.00 EA H15-070601-16-16 UNION, BULKHEAD, MALE 1 JIC
57 4.00 EA H15-080118-08 BULKHEAD, NUT, 1/2
58 2.00 EA H15-070958-16-16-16 BULKHEAD, RUN TEE, MALE 1 JIC
59 3.00 EA H15-080118-16 BULKHEAD, NUT, 1
60 1.00 EA H15-1030-010 QUICK NIP, 1 1/4 NPT
61 2.00 EA H15-140140-20-16 BUSH, HEX, MALE 1 1/4 NPT, FEM 1 NPT
62 9.00 EA H25-1005-010 CLAMP, DOUBLE, 3/4 IN DIA
63 8.00 EA M10496 CONE, TPRD ROL BRG, 2.50 B, 1.1875 W
65 8.00 EA M10674 CUP, TPRD ROL BRG, 4.4375 OD, 0.9375 W
66 4.00 EA M10636 RETNG RING, SPIRAL, EXT, 1.75 IN
67 2.00 EA M10985 HOSE CLAMP, TWIN, 1-1/2 IN
68 2.00 EA M10986 HOSE CLAMP, SINGLE, 1-1/2 IN
69 2.00 EA M11100 TOP COVER, HOSE CLAMP, SINGLE, 5 SER
70 2.00 EA M11101 TOP COVER, HOSE CLAMP, TWIN, 5 SER
71 1.00 EA N10337 PROXIMITY SWITCH, 18mm
72 8.00 EA SS-0250NF-0038 SET SCREW 1/4-28UNF x 0.38, CONE POINT
86 3.00 EA HH-8MM-20MM-GR8 CAPSCR, HEX HD, M8 x 20, GR8.8
Printed: 7/11/2008
Engineering
Bill of Material
Part: 112300002
Description: PIVOT ARM ASSY
Eng ID: 4
Drawing ID: 112300002 Rev No: A
01 2.00 EA 122300009 ASSEMBLY, VERTICAL LIFT, WRENCH ARM

02 1.00 EA 122300011 WRENCH ARM PIVOT ASSEMBLY
03 1.00 EA 131100081 FILTER MOUNT
04 1.00 EA 131100111 MAIN BOOM ASSEMBLY
05 1.00 EA 131100112 JIB BOOM ASSEMBLY
06 1.00 EA 131100115 TIE BAR ASSEMBLY
07 1.00 EA 131100250 WRENCH ARM VALVE MOUNT
08 1.00 EA 131100252 WELDMENT, COUNTER BALANCE VALVE
09 1.00 EA 131100279 SIDE BRACKET - LEFT
10 1.00 EA 131100280 SIDE BRACKET - RIGHT
11 8.00 EA 141100199 PLATE, PIN LOCK
12 1.00 EA 141100586 WRENCH VERTICAL TUBE MOUNT
13 1.00 EA 141100587 WRENCH VERTICAL TUBE MOUNT-LEFT
14 1.00 EA 141101080 PLATE, PROXIMITY BRACKET
15 1.00 EA 141101084 PLATE, PROXIMITY SENSOR GUARD
16 1.00 EA 141500037 PLATE, FILTER BRACKET SPACER
17 1.00 EA 152100059 PROFILE, 1 IN OD x .120W TUBING, SHORT
18 1.00 EA 152100060 PROFILE, 1 IN OD x .120W TUBING, LONG
19 4.00 EA 161100046 PIVOT PIN MAIN BOOM
20 4.00 EA 161100047 PIVOT PIN THREADED
21 1.00 EA 161100048 PIVOT ARM REAR CYLINDER PIN
22 1.00 EA 161100049 PIVOT ARM FRONT CYLINDER PIN
23 4.00 EA 161100142 HEX NUT
24 4.00 EA 161400003 CYLINDER FLANGED BUSHING
25 0.00 EA AY50148 ARM ELECTRICAL BOX
26 1.00 EA AY50130 ARM CONTROL VALVE
27 1.00 EA AY50517 SENSOR, LINEAR DISPLACEMENT, 450 STRK
28 2.00 EA E12540 SPACER, 1/2 x .049W TUBE
29 2.00 EA H10323 (OBSOLETE)VLV, CBAL, 4.5 PILOT, 3000 PSI
30 1.00 EA H10330 VLV, HYD, FLOW DIVIDER
31 1.00 EA H10335 CYL, HYD, HOR SLIDE
32 1.00 EA H10341 FILTER, H PRESS, 6 MICRON
33 4.00 EA H10422 TUBE CLAMP, 1 IN, TWIN ASSY
34 1.00 EA H10464 COUPLER, QUICK CONNECT, 1 IN, STEEL
35 1.00 EA H10465 NIPPLE, QUICK CONNECT, 1 IN, STEEL
36 1.00 EA H10466 COUPLER, QUICK CONN, 1 1/4, BRASS, 1 1/4
37 2.00 EA H10467 COUNTERBALANCE VALVE
38 1.00 EA H10473 ADPT, 90°, MALE 1/2 ORB, MALE 1/2 ORB
39 2.00 EA H10565 ADPT, 90° SWV, MALE JIC FLARE ARM
40 1.00 EA H10586 PLUG, DUST, QUICK CONN 1 1/4 IN, BRASS
Printed: 7/11/2008
A
53
H
4 5
88 75 10
45 84 90
69 68 70 67 37 46 1
14
2 96 94 90
66
92 D
82
1
24 13
85
G
90
6
94
22 12
95 21
92
62 77
89
91 73 59
79
86
91 74 25 17
26 7
33
18
58 50
J L
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE PIVOT ARM ASSEMBLY
REV. DESCRIPTION DATE •FAX: (403) 233-2667 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
A UPDATED HARDWARE AS PER ECN #1165 6/10/2008 •WEBSITE: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
1 OF 3
DEV-25 UPDATED BOM TO AS BUILT SPECIFICATION 12/14/2007
DEV-24 ADDED COUPLERS FOR HPU CONNECTION, ADDED OTHER HYD ADAPTERS 12/4/2007 CREATED: January 08, 2007 5:10:38 PM PART NO: 112300002 REV. A
11 87
64
20
65
63 78 92
65 63
78 5 19 63 20 11
11 19
23
92 78 87 78
64
64
64 72
23
DETAIL A SECTION B-B

TYP PIN CONNECTIONS TYP PIN CONNECTIONS
4 PLCS 4 PLCS
80 89 89 98
8 28 27
37
38 27 45
5 39
27
95
76 88 88 97
46
31 38
31 45
SECTION C-C B B
DETAIL D
C
C
91 77
62
DETAIL M
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE PIVOT ARM ASSEMBLY
2 OF 3
CREATED: January 08, 2007 5:10:38 PM PART NO: 112300002 REV. A

47
91 74
30
74
51
91 15 71
13
DETAIL G DETAIL H
?
57 56 54
3 48 55 94 96 49
45
90 85
44
16 83 29 52 57
93
32 48 59
DETAIL J DETAIL K
34
35
61
43 K
36
42
60
41
61
40
DETAIL L

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE PIVOT ARM ASSEMBLY
Bus. (403) 237-6400
Fax. (403) 233-2667
January 08, 2007 5:10:38 PM 112300002 A
Engineering
Bill of Material
Part: 122100003
Description: JAW ASSEMBLY
Eng ID: 0
01 1.00 EA 131100184 RAM JAW

02 2.00 EA 161100128 DIE RETAINER BLOCK
03 2.00 EA 161100129 DIE RETAINER BOLT
04 1.00 EA 161100130 RAM CONNECTION BOLT
05 4.00 EA 161100210 TONG DIE
07 2.00 EA R10272 MINI DIE, 2, 3.5 SM TOOTH PATTERN
08 1.00 EA H10337 CYL, JAW CLAMP
09 4.00 EA SH-0312NC-0075-BR CAPSCR, HEX SOC HD, 5/16-18UNC x .75, BR
10 2.00 EA 161500005 PIVOTING DIE SPACER
Printed: 7/11/2008
3
10
9 8
ASSEMBLE ONE LEFT/ONE RIGHT

CYLINDER ARRANGEMENT IS ONLY DIFFERENCE
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE JAW ASSEMBLY
1 OF 2
REV. DESCRIPTION DATE APPROVED WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-05 ADDED DIE SPACERS, LEFT/RIGHT VIEW 7/30/2007
DEV-04 UPDATED REV LEVEL AND BOM 06/03/2007 CREATED: March 06, 2007 2:09:23 PM PART NO: 122100003 REV. DEV-05
10 6
10 5
16
16
17
REMOVAL OF DIES
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE JAW ASSEMBLY
2 OF 2
CREATED: March 06, 2007 2:09:23 PM PART NO: 122100003 REV. DEV-05
Engineering
Bill of Material
Part: 122100004
Description: POWER PACK, HYD, 480 VAC
Eng ID: 0
Drawing ID: 122100004 Rev No: REL-04
01 1.00 EA 161900001 ADPT, PUMP-MOTOR, W/ HOLES

02 1.00 EA E12113 MOTOR, LH, 50HP/460VAC 324TC-TEFC
03 1.00 EA H10312 PUMP, PISTON, 145cc, RRW, 5000PSI
04 1.00 EA AY50175 DRIVE CPLG ASSY, JAW, 50HP
05 1.00 EA H10425 ADPT, SUC AND RET, 90°, 150 PSI
Printed: 7/11/2008
2
4
6 8
1
4
3
7 8

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE HYDRAULIC POWER PACK, 480 VAC
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-04 UPDATED PART NUMBERS AND EXPLODED VIEWS 23/04/2007 April 26, 2006 11:40:09 AM 122100004 REL-04
Engineering
Bill of Material
Part: 122100007
Description: TONG ASSEMBLY
Eng ID: 0
01 1.00 EA 131100493 LOWER TONG FRAME

02 1.00 EA 131100498 UPPER TONG FRAME
03 2.00 EA 141100402 PLATE, BRASS WEAR RING RETAINER
04 1.00 EA 141400003 PLATE, BRASS WEAR RING
05 2.00 EA 161100272 BEARING RING BACKUP
06 4.00 EA M10668 GREASE NIPPLE, 1/8 NPT, 90°
09 8.00 EA SH-0500NC-0225 CAPSCR, HEX SOC HD, 1/2-13UNC x 2.25
11 8.00 EA LW-0500-HS-HC LOCKWASHER, 1/2 HELICAL SPR, HIGH COLLAR
Printed: 7/11/2008
2 7
3 6
7
10 8
11 9
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TONG ASSEMBLY
REV. DESCRIPTION DATE •WEBSITE: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
1 OF 2
DEV-05 UPDATED BRASS RING, AND RING BACK-UP REV LEVELS AND ADDED 9/24/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
INSTALLATION NOTES SHEET 2
DEV-04 UPDATED REV LEVEL AND BOM 06/03/2007 CREATED: March 06, 2007 3:17:20 PM PART NO: 122100007 REV. DEV-05
UPPER & LOWER TONG
INSTALLATION
INSTALLATION NOTES;
1. TO INSTALL UPPER TONG ON TOP OF LOWER
TONG, FIRST LINE UP THE RH SIDE OF THE UPPER
TONG 45 FROM THE LOWER TONG AS SHOWN
TO THE LEFT.
2. PLACE THE UPPER TONG RING INTO THE
LOWER TONG RING GROOVE.
3. ROTATE CLOCKWISE UNTIL BOTH TONGS ARE
PARALLEL.
45°
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TONG ASSEMBLY
2 OF 2
CREATED: March 06, 2007 3:17:20 PM PART NO: 122100007 REV. DEV-05
Engineering
Bill of Material
Part: 122200006
Description: SPINNER TRACK JEEP, TM-120
Eng ID: 1
01 1.00 EA 122200007 SPINNER TRACK V MOUNT

02 1.00 EA 122200008 SPINNER JEEP CARRIAGE
03 2.00 EA 141100444 PLATE, SPINNER FLOAT SPRING WASHER
04 2.00 EA 152100097 PIPE, 1.0 x SCH 40 x 0.500
05 1.00 EA 158100002 READY ROD 1" - 8 UNC
06 1.00 EA 161100151 SPINNER JEEP RETAINER
07 2.00 EA M10634 SPR, COIL, 2500 x 12
12 6.00 EA FW-1000-A WASHER, F, 1, PLAIN, TYPE A
14 2.00 EA HN-1000NC-GR8 HEX NUT, 1-8UNC, GR8
16 2.00 EA LN-1000NC-NL-GR8 LOCKNUT, 1-8UNC, NYLOCK, GR8
Printed: 7/11/2008
Engineering
Bill of Material
Part: 122200007
Description: SPINNER TRACK V MOUNT
Eng ID: 0
01 1.00 EA 131100123 JEEP BED

02 1.00 EA 141100211 SUPPORT MOUNT, TM-80 JEEP
03 2.00 EA 161100007 SPINNER JEEP SPRING ROD MOUNT
Printed: 7/11/2008
4 6
5 6
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SPINNER TRACK V MOUNT
•WEBSITE: www.canrig.com
LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
1 OF 1
DEV-03 FIXED DRAWING DETAILS UPDATED BOM 10/24/2007
DEV-02 UPDATED REV LEVEL AND BOM 08/03/2007 CREATED: Thursday, March 08, 2007 9:23:44 PART NO: 122200007 REV. DEV-03
Engineering
Bill of Material
Part: 122200008
Description: SPINNER JEEP CARRIAGE
Eng ID: 0
01 1.00 EA 131100124 SPINNER JEEP FRAME

02 1.00 EA 131100209 JEEP ROLLER MOUNT - LH
03 1.00 EA 131100210 JEEP ROLLER MOUNT - RH
04 2.00 EA 141500003 PLATE, SIDE RAIL
05 2.00 EA 161100150 SPINNER JEEP STAND OFF
06 2.00 EA M10527 CAM FOLLOWER, 1.250 IN OD
07 2.00 EA M10528 CAM FOLLOWER, 2.00IN OD, ECCENTRIC STUD
08 2.00 EA M10635 SPR, 0.437 x 3.374 x 16 x 128 LBS/IN
11 8.00 EA FH-0312NC-0100 CAPSCREW, FLAT HD, 5/16-18UNC x 1.00
13 2.00 EA LN-0500NF-L9 LOCKNUT, 1/2-20, L9, STOVER
15 2.00 EA LN-0875NF-L9 LOCKNUT, 7/8-14UNF, L9, STOVER
Printed: 7/11/2008
8
10
13 6 5 14
12 9
15
7 4 11
1 2
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SPINNER JEEP CARRIAGE
•WEBSITE: www.canrig.com
LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
1 OF 1
DEV-05 REPLACED LOCK NUTS / UPDATED BOM 10/24/2007
DEV-04 UPDATED REV LEVEL AND BOM 08/03/2007 CREATED: Thursday, March 08, 2007 9:31:17 PART NO: 122200008 REV. DEV-05
Engineering
Bill of Material
Part: 122200010
Description: BULKHEAD MOUNT ASSEMBLY
Eng ID: 0
01 1.00 EA 141100439 PLATE, SPINNER ASSY HYD. BULKHEAD

02 2.00 EA H15-070601-08-08 UNION, BULKHEAD, MALE 1/2 JIC
04 3.00 EA H15-080118-08 BULKHEAD, NUT, 1/2
05 2.00 EA H15-080118-12 BULKHEAD, NUT, 3/4
06 1.00 EA H15-070959-08-08 BULKHEAD, TEE, 8 JIC BRANCH
Printed: 7/11/2008
5
6 2
NOTICE
REV. DESCRIPTION DATE APPROVED
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE BULKHEAD MOUNT ASSEMBLY
DEV-03 UPDATED MIDDLE FITTING TO A TEE 10/25/2007 •FAX: (403) 233-2667 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
1 OF 1
DEV-02 ISSUED FOR MANUALS 24/05/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-01 ISSUED FOR MANUALS 06/03/2007 CREATED: March 06, 2007 5:46:28 PM PART NO: 122200010 REV. DEV-03
Engineering
Bill of Material
Part: 122200012
Description: ROLLER FRAME
Eng ID: 1
01 1.00 EA 131100466 ROLLER FRAME

02 2.00 EA M10641 DWL PIN, 1/2 x 1 IN, GRD & HDNED
03 2.00 EA M10601 BUSH, 1.5 B x 1.75 OD x 1 WIDTH
Printed: 7/11/2008
3
5 6
4 5
NOTICE
REV. DESCRIPTION DATE APPROVED •PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ROLLER FRAME
DEV-08 UPDATED HDW COMPONENTS 3/11/2008 •WEBSITE: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED 1 OF 1
DEV-07 UPDATED TEMPLATE AND DWG 10/05/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-06 ISSUED FOR MANUALS 06/03/2007 CREATED: March 06, 2007 6:01:01 PM PART NO: 122200012 REV. DEV-08
Engineering
Bill of Material
Part: 122200013
Description: SPINNER ROLLER
Eng ID: 1
01 1.00 EA 122200012 ROLLER FRAME

02 1.00 EA 149900001 GEAR BOX GASKET
03 2.00 EA 161100113 GROOVED ROLLER
04 2.00 EA 161100115 SPINNER OUTPUT GEAR
05 2.00 EA 161100117 ROLLER KEY
06 2.00 EA 161100119 GEAR KEY
07 1.00 EA 161100168 SPINNER MOTOR MOUNT
08 1.00 EA 161100169 SPINNER INPUT GEAR
09 1.00 EA 161100170 SPINNER GEAR BOX
10 1.00 EA 161100172 MOTOR SHAFT BUSHING
11 4.00 EA 161100173 STUD
12 2.00 EA 161100253 BEARING CAP
13 2.00 EA 161100259 SPINNER ROLLER SHAFT
14 4.00 EA 161100260 SPACER WASHER
15 2.00 EA 161100261 SPACER GEAR TRUST WASHER
16 1.00 EA 161400005 MOTOR SPACER
17 1.00 EA H10421 HYDRAULIC MOTOR
17A 0.00 EA M11127 KEY, EATON 10,000 SERIES MOTOR
18 1.00 EA M10500 BRG, BALL, 70mm x 110mm x 20mm
19 4.00 EA M10644 NEEDLE BEARING
20 2.00 EA M10642 DWL PIN, 1/2 x 1-1/2 IN, GRD & HDNED
22 4.00 EA S10104 OIL SEAL
23 2.00 EA M10491 RETNG RING, SPIRAL, EXT, 2.25 IN
24 2.00 EA M11-1029-010 RETNG RING, EXT
25 1.00 EA P10065 PLUGS, 1/8 IN NPT BREATHER
29 3.00 EA SS-0250NC-0025 SETSCREW 1/4-20UNC x 0.25, CUP POINT
Printed: 7/11/2008
Engineering
Bill of Material
Part: 122300009
Description: ASSEMBLY, VERTICAL LIFT, WRENCH ARM
Eng ID: 2
01 1.00 EA 131100275 VERTICAL LIFT PROFILE

02 1.00 EA 131100277 VERTICAL LIFT PROFILE INNER
03 1.00 EA 131100278 TOP CYLINDER MOUNT PLATE
04 8.00 EA 141500023 PLATE, SLIDE PAD
05 1.00 EA H10336 CYL, HYD, VERT LIFT, 180° PORTS
06 1.00 EA H25-1005-010 CLAMP, DOUBLE, 3/4 IN DIA
15 8.00 EA FW-1000-A WASHER, F, 1, PLAIN, TYPE A
20 2.00 EA 161100385 CYLINDER PIN, TM-80 V-LIFT
21 2.00 EA M11165 PIN, LYNCH, 3/16IN x 1 9/16IN
Printed: 7/11/2008
10 14
20
21
7
18 13
15 USE 4 FW AS SPACERS TO CENTER CYL
11
19 17 14
13 18
12
NOTICE
•PHONE: (403) 237-6400 HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSEMBLY, VERTICAL LIFT, WRENCH ARM
REV. DESCRIPTION DATE LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED 1 OF 1
•WEBSITE: www.canrig.com IN ANY MANNER FOR ANY PURPOSE WHATSOEVER
A ADDED NEW PINS 5/15/2008 WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-08 UPDATED BOM TO AS BUILT SPECIFICATION 12/13/2007
DEV-05 UPDATED TO MATCH REVISION LEVELS 01/03/2007 CREATED: January 10, 2007 2:26:01 PM PART NO: 122300009 REV. A
Engineering
Bill of Material
Part: 122300011
Description: WRENCH ARM PIVOT ASSY, TM-80/120
Eng ID: 2
01 1.00 EA 131100385 BOTTOM PLATE ASSEMBLY

02 1.00 EA 131100384 TOP PIVOT ASSEMBLY
03 1.00 EA 131100460 BASE GUARD FRONT
04 1.00 EA 131100461 BASE GUARD REAR
05 1.00 EA 156100113 GEAR KEY, TM80/120 BASE
06 1.00 EA H10423 HYDRAULIC MOTOR
07 1.00 EA H10437 GEAR BOX
10 1.00 EA H15-080118-02 BULKHEAD, NUT, 1/8
11 1.00 EA M10497 BRG, TURNABLE, 24.650 x 16.250 x 2.375
13 1.00 EA M10596 GEAR, SLEWING PINION, 17 T, 4 DP
18 16.00 EA HH-1000NC-0275-GR8 CAPSCR, HEX HD, 1-8UNC x 2.75, GR8
24 16.00 EA LW-1000-HS LOCKWASHER, 1 HELICAL SPR
Printed: 7/11/2008
6
21 15
BLUE LOCTITE
55 FT.LBS
2PL
7
2
22 16
BLUE LOCTITE
110 FT.LBS
4PL
BLUE LOCTITE
200 FT.LBS
4 16PL
11
17 23
5
BLUE LOCTITE
200 FT.LBS
20PL
13
18 24
MOUNTING TO POCKET
BLUE LOCTITE
680 FT.LBS 14 20 19
16PL

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE WRENCH ARM PIVOT ASSEMBLY, TM-80/120
REV. DESCRIPTION DATE Website: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
Bus. (403) 237-6400 IN ANY MANNER FOR ANY PURPOSE WHATSOEVER SHEET 1 OF 2
DEV-13 UPDATED HARDWARE, UPDATED DWG FOR CLARITY, ADDED TORQUE SPECS 2/14/2008 Fax. (403) 233-2667
DEV-12 UDPATED FITTINGS ON PIVOT BASE MOTOR 11/15/2007 DATE CREATED: PART NO: REV:
DEV-11 ADDED KEY & LOCK WASHER & ADAPTERS 10/24/2007 March 27, 2007 1:20:03 PM 122300011 DEV-13
8
A A
DETAIL C
SCALE 1 : 4 C
12
DETAIL B
SCALE 1 : 4 SECTION A-A
SCALE 1 : 16

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE WRENCH ARM PIVOT ASSEMBLY, TM-80/120
Bus. (403) 237-6400
Fax. (403) 233-2667
March 27, 2007 1:20:03 PM 122300011 DEV-13
Engineering
Bill of Material
Part: 183200001
Description: PLUMBING LAYOUT, TM120
Eng ID: 1
Drawing ID: 183200001 Rev No: D
01 1.00 EA AY50275 HOSE ASSY, WRENCH ARM

02 1.00 EA AY50276 HOSE ASSY, TONG VLV TO ELEC BOX
03 1.00 EA AY50277 HOSE ASSY, TONG VLV TO TONGS, BLKHD
04 1.00 EA AY50278 HOSE ASSY, PRESS & TANK TO TONG VLV
05 1.00 EA AY50279 HOSE ASSY, TONG VLV TO SPINNER BLKHD
06 1.00 EA AY50280 HOSE ASSY, BLKHD TO SPINNER
07 1.00 EA AY50281 HOSE ASSY, PIVOT BEARINGS
08 1.00 EA AY50282 HOSE ASSY, QUICK COUPLERS
09 1.00 EA AY50283 HOSE ASSY, UPPER TONG PLUMBING
10 1.00 EA AY50284 HOSE ASSY, LOWER TONG PLUMBING
11 1.00 EA AY50285 HOSE ASSY, PURGE HOSES
12 1.00 EA AY50286 HOSE ASSY, LIFT CYL HOSES
13 1.00 EA AY50248 HOSE ASSY, POWER UNIT SUPPLY & RET
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50130
Description: TM80/120, ARM CONTROL VLV
Eng ID: 1
Drawing ID: AY50130 Rev No: A
01 1.00 EA AY50506 VLV, ARM CONTROL, WRENCH, 3 SERIES

02 8.00 EA H15-3218-08-12 ADPT, MALE 1/2 JIC, MALE 3/4 BSPP, STEEL
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE KIT, ARM CONTROL VLV, 3 SER, 3 BANK
Bus. (403) 237-6400
Fax. (403) 233-2667
A UPDATED VALVE BANK TO VSA 3/25/2008 DATE CREATED: PART NO: REV:
REL-01 RFM 10/26/2007 October 26, 2007 2:16:22 PM AY50130 A
Engineering
Bill of Material
Part: AY50131
Description: TM-120 LIFTING CHAIN
Eng ID: 1
Drawing ID: AY50131 Rev No: REL-03
01 108.50 IN M11136 CHAIN, BULK, 1/2IN x 65IN, BLUE

02 1.00 EA M11137 LINK, CHAIN, 1/2IN OBLONG, GR8
03 4.00 EA M11138 LINK, CHAIN, 1IN OBLONG, GR8, ALLOY
04 8.00 EA M11139 HAMMER LOCK, 1/2 GR80
05 4.00 EA M11140 SHACKLE, 3/4, ANCHOR SCREW PIN, 4-3/4
Printed: 7/11/2008
2
27 LINKS
42 LINKS
5

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TM-120 LIFTING CHAIN
REV. DESCRIPTION DATE Bus. (403) 237-6400 IN ANY MANNER FOR ANY PURPOSE WHATSOEVER SHEET 1 OF 1
Fax. (403) 233-2667
REL-03 UPDATED TO AS BUILT SPECIFICATION 12/17/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
REL-02 UPDATED PARTS 2 AND 3 11/6/2007 DATE CREATED: PART NO: REV:
REL-01 10/12/2007 October 12, 2007 9:11:36 AM AY50131 REL-03
Engineering
Bill of Material
Part: AY50137
Description: ASSY, ELEC, TM120, ARM
Eng ID: 2
Drawing ID: NO DRAWING Rev No: 0
01 1.00 EA AY50145 MAIN PANEL BOX

02 1.00 EA AY50146 DRILLER'S CONSOLE
03 1.00 EA AY50148 ARM ELECTRICAL BOX
04 1.00 EA AY50149 TONG ELECTRICAL BOX
05 1.00 EA 182200001 SCHEMATIC, ELEC, WRENCH
Printed: 7/11/2008
Engineering
Bill of Material
42 2.00 EA E13525 FTG, CONDUIT, 3/4IN
43 1.00 EA E13527 FTG, CONDUIT, 3/4IN NPT, LEFT ELBOW
44 1.00 EA E12417 FTG, CONDUIT, 3/4 NPT, RIGHT ELBOW
45 4.00 FT E13526 CONDUIT, ALUM, 3/4IN
47 1.00 EA E12804 NIPPLE, GALVANIZED RIGID, 3/4 x 3-1/2
48 2.00 EA E12450 HOOD, DB9
49 2.00 EA E12451 PIN, DP90, MALE
50 1.60 FT E13532 CABLE, 3C-#18, OS (RS232)
51 1.60 FT E13533 CABLE, 3P-#22, IS (COMMUNICATION)
52 150.00 FT E12382 WIRE, STRANDED, 1C - #18 AWG TEW
53 2.00 EA E12390 TERMINAL, STAKON, 1/4IN BOLT HOLE
54 1.00 EA E12791 MARKER, WIRE #18-12
55 104.00 EA E13518 LABEL, TERMINAL, PRINTED 1-14, ZB6
56 35.00 EA E13369 MARKER STRIP, UNPRINTED, ZB6
61 1.00 EA C10058 CORROSION PROTECTANT, ELECTRICAL
65 1.00 EA E12877 CONNECTOR, 37 TO 37 PYLE PIN
REF 100.00 FT E11371 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,GRN
REF 300.00 FT E11370 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,WHT
REF 100.00 FT E11372 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,BLK
REF 300.00 FT E11374 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,RED
REF 300.00 FT E11430 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,YEL
REF 300.00 FT E11373 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,ORN
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50145
Description: ASSY, ELEC, MAIN PANEL BOX, WRENCH
Eng ID: 3
01 1.00 EA 158100047 ENCLOSURE, 4 x 24H x 24W x 12D

02 0.00 EA E12438 BACK PAN, 22.20 x 22.20
03 1.00 EA N10336 VENT, PURGE SYSTEM, 1-1/4IN MYERS HUB
04 1.00 EA E12159 POWER SUPPLY UNIT, 24VDC, 5A, 5 VDC
05 1.00 EA N10330 CPU UNIT, 960 I/O POINTS, 10K CAPACITY
06 3.00 EA N10325 INPUT MODULE, DC, 16 INPUTS, 24VDC, 7mA
07 2.00 EA N10326 OUTPUT MODULE, RELAY BIT, 250VAC/24VDC
08 1.00 EA N10327 INPUT MODULE, ANALOG, 8 INPUTS, 4 - 20mA
09 2.00 EA N10328 OUTPUT MODULE, ANALOG, 4 OUTPUTS, 4-20mA
10 1.50 FT E13519 DIN RAIL, NS 35/7.5, PERFORATED
11 15.00 EA E12442 TERMINAL, KNIFE DISCONNECT,UKK 5-MTK-P/P
12 56.00 EA E12443 TERMINAL, 2 TIER, FUSE, UKK 5-TG
13 56.00 EA E12444 PLUG, FUSE, ST-SI-UK-4
14 56.00 EA E13530 FUSE, 2A, 250V, 5 x 20mm
15 5.00 EA E12035 DRIVER CARD, DUAL CHANNEL, 24VDC
16 5.00 EA E12355 RELAY, BASE, 11 PIN
17 2.00 EA E12162 COVER, WIDTH 2.5mm, GRAY
18 11.00 EA E12161 TERMINAL BLK, 2 TIER, UKKB 5
19 7.00 EA E12369 GROUND TERMINALS, USLKG 5
20 13.00 EA E12782 (OBSOLETE) ANCHOR, END, E/NS 35 N
21 6.00 EA E12448 TERMINAL, BREAKER, UK6-FSI/C
22 2.00 EA E12127 BREAKER, CIRCUIT, 6 AMP
25 1.00 EA E12130 POWER SUPPLY, 100-240V, 24 VDC, 10A
26 10.00 FT E12433 DUCT, WIRING, 1.5 W x 3 H
27 3.00 FT E12368 DUCT, WIRING, 2 IN x 3 IN
28 10.00 FT E12378 DUCT COVER, 1.5 IN, GREY
29 3.00 FT E12379 DUCT COVER, 2 IN, GREY
30 1.00 EA AY50159 RECIEVER, NOVA-XL PROP 6K
31 1.00 EA AY50157 TRANSMITTER, NOVA-XL ZONE 2
32 2.00 EA E13085 BASE, SERIES E, DBL LEVEL
33 1.00 EA E12356 INSERT, MALE, 24 P+E, 16A, 500V
34 1.00 EA E12359 HOOD, SERIES E, 4 PEGS, SIDE ENTRY, 1NPT
35 2.00 EA E12357 INSERT, FEM, 24 P+E, 16A, 500V
36 1.00 EA E04-2015-010 STRAIN RELIEF, 1 NPT, 0.625 - 0.750
37 1.00 EA 291-00256 LOCKNUT, 1' STEEL, W/GASKETED SEAL
38 1.00 EA E04-2028-010 SEALING RING, 1 NPT
40 1.00 FT C10083 SPIRAL, WRAPPING, 1/2 INCH
41 1.00 EA E13531 COVER, 4 PEGS
Printed: 7/11/2008
10 42
51 52 53 54 55 12 5 32
4 11 4
4 18
11
25 21
41 40 36 43 37 35
4
6 8
7 4 38 17
DETAIL A 19
56 57 58
19 4
5
30 12
4 9
20
31
46 A B
47 45 34 50 48
DETAIL B
28 27
33
16
13
15
14
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSY, ELEC, MAIN PANEL BOX, HPU
REV. DESCRIPTION DATE Bus. (403) 237-6400 IN ANY MANNER FOR ANY PURPOSE WHATSOEVER SHEET 1 OF 1
Fax. (403) 233-2667
REL-03 UPDATED TO AS BUILT 1/16/2008 WITHOUT WRITTEN CONSENT OR DIRECTION.
REL-02 POST TM-80 PRODUCTION 10/18/2007 DATE CREATED: PART NO: REV:
REL-01 RFM 8/31/2007 August 31, 2007 10:23:31 AM AY50145 REL-03
Engineering
Bill of Material
44 1.00 EA E12791 MARKER, WIRE #18-12
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50146
Description: ASSY, ELEC, DRILLERS CONSOLE, WRENCH
Eng ID: 3
01 1.00 EA 158100048 PANEL, CUSTOM, 4X, 435H x 385W x 135D

02 1.00 EA E12455 PANEL, 18.20 x 14.20, STEEL
03 1.00 EA E12429 TOUCH SCREEN, 12 IN
04 1.00 EA E12457 JOYSTICK, 4-WAY, SPR RTN
05 1.00 EA E13534 PB, RED, MUSHROOM, PUSH-PULL
06 1.00 EA E12458 PB, BLACK, FLUSH HD, TYPE 4/13
07 1.00 EA E12459 PB, RED, FLUSH HD, TYPE 4/13
08 1.00 EA E06-6014-010 SWITCH, PB, MOMENT, GREEN, 1-NO
09 1.00 EA E13535 SS-2POS, MAINTAINED
10 3.00 EA E06-2003-010 CONTACT BLOCK, 1-NO, SEALED (INACTIVE)
11 1.00 EA E10436 CONTACT BLOCK, 1-NC, SEALED
12 3.00 EA E06-2004-010 CONTACT BLOCK, 1-NO 1-NC, SEALED
13 25.00 EA E12422 TERMINAL, SINGLE, UK 5 N
14 2.00 EA E12423 TERMINAL, SINGLE BARRIER, D-UK 4/10
16 1.00 EA E10541 JUMPER BAR, 10 POLE, UKD4
18 2.00 EA E10955 END BRACKET, TS 35 RAIL, 9.5MM
22 3.00 FT E12215 DUCT COVER, F1.5 x 1.5, G6
24 1.00 EA E12359 HOOD, SERIES E, 4 PEGS, SIDE ENTRY, 1NPT
25 1.00 EA E12356 INSERT, MALE, 24 P+E, 16A, 500V
26 1.00 EA E13536 COVER, SERIES E, DBL LEVEL
28 66.00 FT E13537 CABLE, 24C-#16, 600V, 90C (D=18)
29 6.00 FT E13532 CABLE, 3C-#18, OS (RS232)
30 6.00 FT E13533 CABLE, 3P-#22, IS (COMMUNICATION)
31 2.00 EA E12450 HOOD, DB9
32 1.00 EA E12451 PIN, DP90, MALE
33 1.00 EA E12462 PIN, DP9, FEM (PLC)
Printed: 7/11/2008
3
6
16
11
20
4
10
17
18
26
27
24
25
DETAIL A
2 SCALE 1 : 3
28
34
22
21
33 33
35
5 33 19
36
5
37
8

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSY, ELEC, DRILLERS CONSOLE, WRENCH
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-01 RFM 9/5/2007 August 30, 2007 1:46:16 PM AY50146 REL-02
Engineering
Bill of Material
41 3.00 EA E04-2000-010 STRAIN RELIEF, 1/2 NPT, 0.250 - 0.375
42 7.00 FT E12216 CABLE, V47, POWER VLV AND LEVEL SW
43 5.00 EA E11322 LOCKNUT, 1/2 NPT STEEL, W/GASKETED SEAL
44 5.00 EA E04-2027-010 SEALING RING, 1/2 NPT
46 2.00 EA E13525 FTG, CONDUIT, 3/4IN
47 1.00 EA E13527 FTG, CONDUIT, 3/4IN NPT, LEFT ELBOW
48 1.00 EA E12417 FTG, CONDUIT, 3/4 NPT, RIGHT ELBOW
49 1.00 EA E12469 BUSH, GROUND, 1 IN
50 14.00 FT E13526 CONDUIT, ALUM, 3/4IN
51 1.00 EA E12791 MARKER, WIRE #18-12
56 8.00 EA E12467 LUG, COMP, #10-8
57 3.00 EA E13528 LUG, COMP, #4-6
65 12.00 EA FS-10-24-0075 CAPSCR, FLAT HD SOC, #10-24UNC x 0.75
68 18.00 EA PH-P-10-32-0050-SS PAN HD, MACH SCR, PHILLIPS #10-32 x 0.50
REF 10.00 FT E11371 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,GRN
REF 20.00 FT E11372 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,BLK
REF 300.00 FT E11370 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,WHT
REF 300.00 FT E11430 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,YEL
REF 300.00 FT E11374 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,RED
REF 300.00 FT E11373 CABLE, 1 C #18 AWG, 19 STRANDS, 600V,ORN
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50147
Description: ASSY, ELEC, HPU, STARTER PANEL, 480V
Eng ID: 4
01 1.00 EA 158100049 ENCLOSURE, CSA 4X, 24H x 16W x 80

02 0.00 EA E12465 BACK PAN, 22IN x 14IN
03 1.00 EA E12189 RECEPTACLE, 100 AMP, 3 WIRE, 4 POLE
04 1.00 EA E12412 ADPT, 90° ANGLE
05 1.00 EA E12809 XFMR, 480V-120V, 1.5KVA
06 3.00 EA E12389 SNAP BLK, DIST, 175A
07 1.00 EA E12393 COVER, DISTRIBUTION BLK, 3 x 3 x 1/8
08 1.00 EA E12180 STARTER, 75HP @ 460V, c/w 120V COIL
09 1.00 EA E12786 MOTOR OVERLOAD, MANUAL, 57-70 AMP
10 2.00 EA E12302 CONTACTOR, 120 V, 60 Hz, 3 PH
11 1.00 EA E12464 CONTACTOR O/L, 4.5 - 6.3A
12 1.00 EA E12163 CONTACTS, AUX TOP MOUNT, 70-90 AMP
13 1.00 EA E13517 LUG, GROUND, ALUM, 2-(#2-14)
14 3.00 EA E12041 RELAY, POWER PCB, 24VDC, 5A, 1 FORM C
15 3.00 EA E12158 BASE, RELAY, 1 POLE
16 1.00 EA E12364 BREAKER, CIRCUIT, 6A, 3 POLE
17 1.00 EA E12171 BREAKER, CIRCUIT, 3A, 2P, 600V, 3KIC
18 14.00 EA E12366 TERMINAL BLKS, 2 TIER, UKKB3
21 8.00 EA E12782 (OBSOLETE) ANCHOR, END, E/NS 35 N
25 1.00 EA E12789 LUG, GROUND, SINGLE TERMINAL, ALUM
33 1.00 EA E13520 FTG, TECK, 1IN NPT (1.187IN - 1.375IN)
34 1.00 EA H15-1000-10 NUT, LOCK 1 IN, GROUND
35 10.00 FT E03-1017-010 CABLE, 4 C #4 AWG, EXANE, 600V
36 1.00 EA E13522 FTG, TECK, 1/2IN NPT (0.725IN - 0.885IN)
37 1.00 EA H15-0500-10 NUT, LOCK 1/2 IN, GROUND
38 10.00 FT E03-1021-010 CABLE, 4 C #12 AWG, 600V, GENERIC
39 2.00 EA E04-2033-010 CONDUIT FTG, FLEX METAL, STR, 1/2 NPT
40 7.00 FT E13524 CONDUIT, FLEX LIQUID TIGHT, 1/2IN
Printed: 7/11/2008
35 22 24 47
23 4 33 16
28 11
43 31
27
37
15
4
44 A
8
10 6 7
9
DETAIL A
45 13
13 5
34 17
49 26
46
30 29
39
38
49
48

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSY, ELEC, CONTACTOR BOX, 480V
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50148
Description: ASSY, ELEC, ARM BOX, WRENCH
Eng ID: 2
01 1.00 EA 158100050 ENCLOSURE, CSA 4X, 16H x 14W x 6D

02 1.00 EA E13335 BACKPAN, 14.75X12.88, USE WITH E13334
03 1.00 EA N10401 BARRIER, POT, CONVERTER, 4-20 MA
04 22.00 EA E12161 TERMINAL BLK, 2 TIER, UKKB 5
08 1.00 EA E12791 MARKER, WIRE #18-12
13 3.00 FT E12784 DUCT, F1.5 x 2, LG6
16 1.00 EA E12483 PURGE, TYPE Z (DIV. 2), CF PANEL MOUNT
26 1.00 EA E12877 CONNECTOR, 37 TO 37 PYLE PIN
30 14.00 EA FS-10-32-0050 CAPSCR, FLAT HD SOC, #10-32UNF x 0.50
33 4.00 EA LN-8-32 LOCKNUT, # 8-32UNC, STOVER
37 2.00 EA E12380 TERMINAL, RING, 6-14 AWG, #10 STUD
Printed: 7/11/2008
11 2
6
1 9
13 A
20
21
22
2
3
16 18 17 19 5
DETAIL A
7 14
12
10
8

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSY, ELEC, ARM BOX, WRENCH
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50149
Description: ASSY, ELEC, TONG BOX, TM120
Eng ID: 4
01 1.00 EA 158100053 ENCLOSURE, CSA 4X, 12H x 10W x 6D

02 1.00 EA E13337 BACKPAN, 10.75X8.88, USE WITH E13336
03 1.00 EA N10401 BARRIER, POT, CONVERTER, 4-20 MA
04 1.00 EA E12365 BARRIER CARD
05 22.00 EA E12366 TERMINAL BLKS, 2 TIER, UKKB3
08 36.00 EA E13538 LABEL, TERMINAL, PRINTED, 1-36, ZB5
09 8.00 EA E13544 LABEL, TERMINAL, UNPRINTED, ZB5
10 1.00 EA E12791 MARKER, WIRE #18-12
14 3.00 FT E12214 DUCT, F1.5 x 1.5, LG6
16 1.00 EA E12484 FITTING, CORD, 90, (.750 - .875) 90
20 1.00 EA E13025 CABLE, 37 PIN
21 1.00 EA E12485 GLAND, CABLE, 74mm x 51mm
22 3.00 EA N10298 PRESSURE TRANSDUCER
23 3.00 EA H15-2240-04-04 BULKHEAD, 1/4 MALE JIC, 1/4 MALE NPT
28 14.00 EA FS-10-32-0050 CAPSCR, FLAT HD SOC, #10-32UNF x 0.50
29 4.00 EA LW-10-HS LOCKWASHER, #10 HELICAL SPR
30 4.00 EA LN-10-32 LOCKNUT, # 10-32UNF, NYLON INSERT
31 2.00 EA E12380 TERMINAL, RING, 6-14 AWG, #10 STUD
Printed: 7/11/2008
19
16
14 7
8 2 6 3
15
4
5
6
5
14
21
10
17
11 18
13
14
22 24
23 25
26 20

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE ASSY, ELEC, TONG BOX, TM120
Bus. (403) 237-6400
Fax. (403) 233-2667
REV. DESCRIPTION DATE DATE CREATED: PART NO: REV:
Engineering
Bill of Material
Part: AY50155
Description: RADIO CONTROL UNIT, WRENCH, WIRELESS
Eng ID: 0
01 1.00 EA E12273 CHARGER, MINI, 10-30vdc

02 2.00 EA E12102 BATTERY, MINI, NiMH, 3.6V/1.2Ah, GREY,TX
03 1.00 EA AY50159 RECIEVER, NOVA-XL PROP 6K
04 1.00 EA AY50157 TRANSMITTER, NOVA-XL ZONE 2
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50224
Description: TM120, TONG CONTROL VLV
Eng ID: 1
01 1.00 EA AY50466 VLV, TONG CONTROL, TM-120

02 1.00 EA H10333 VLV, HYD, SHUTTLE, CARTRIDGE
03 1.00 EA H15-2250-04-04 ELL 90°, MALE 1/4 NPT, FEM 1/4 JIC
04 2.00 EA H15-070102-04-04 ADPT, MALE 1/4 JIC, MALE 1/4 NPT
06 2.00 EA H15-3218-08-16 ADPT, MALE 1/2 JIC, MALE 1 BSPP, STEEL
07 8.00 EA H15-3218-12-16 ADPT, MALE 3/4 JIC, MALE 1 BSPP, STEEL
08 1.00 EA H15-3218-16-20 ADPT, MALE 1 JIC, MALE 1-1/4 BSPP, STEEL
09 1.00 EA H15-7202-16-20 ELL 90°, MALE 1 JIC, MALE 1 1/4 BSPP
Printed: 7/11/2008
6
10
5 3 2

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TM120, TONG CONTOL VLV, ASSEMBLY
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-02 UPDATED HAWE VLV BANK 3/6/2008 DATE CREATED: PART NO: REV:
REL-01 RFM 10/30/2007 October 30, 2007 2:44:31 PM AY50224 REL-02
Engineering
Bill of Material
Part: AY50248
Description: HOSE ASSY, POWER UNIT SUPPLY & RET
Eng ID: 1
HOSE #56 1.00 EA F721TC16161616-900 HOSE ASSY, 1, NPT MALE, SWV STR, 900
HOSE #57 1.00 EA F451TC16161616-900 HOSE ASSY, 1, NPT MALE, SWV STR, 900
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50275
Description: HOSE ASSY, WRENCH ARM
Eng ID: 2
HOSE #01 2.00 EA F471TC637888-90 HOSE ASSY, 1/2, SWV STR, 45° ELL, 87.5
HOSE #02 2.00 EA F471TC66888-102 HOSE ASSY, 1/2, SWV STR, SWV STR, 100
HOSE #05 2.00 EA F471TC639444-12 HOSE ASSY, 1/4, SWV STR, 90° SHT, 9.5
HOSE #06 1.00 EA F471TC637888-147.75 HOSE ASSY, 1/2, SWV STR, 45° ELL, 145.25
HOSE #09 1.00 EA F471TC3737888-44 HOSE ASSY, 1/2, 45° ELL, 45° ELL, 40
HOSE #10 1.00 EA F471TC3737888-46 HOSE ASSY, 1/2, 45° ELL, 45° ELL, 42
HOSE #13 1.00 EA F721TC137161616-19 HOSE ASSY, 1, 90° SHT, SWV STR, 15
HOSE #14 1.00 EA F451TC639161616-16 HOSE ASSY, 1, SWV STR, 90° SHT, 12
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50276
Description: HOSE ASSY, TONG VLV TO ELEC BOX
Eng ID: 0
HOSE #15 1.00 EA F471TC639444-28 HOSE ASSY, 1/4, SWV STR, 90° SHT, 26
HOSE #17 1.00 EA F471TC376444-25.5 HOSE ASSY, 1/4, SWV STR, 45° ELL, 23
HOSE #18 1.00 EA F471TC396444-6.75 HOSE ASSY, 1/4, SWV STR, 90° SHT, 4.5
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50277
Description: HOSE ASSY, TONG VLV TO TONGS, BLKHD
Eng ID: 1
HOSE #19 1.00 EA F721TC637121212-38 HOSE ASSY, 3/4, SWV STR, 45° ELL, 34
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50278
Description: HOSE ASSY, PRESS & TANK TO TONG VLV
Eng ID: 1
HOSE #25 1.00 EA F721TC36161616-161.25 HOSE ASSY, 1, STR, SWV STR, 157
HOSE #26 1.00 EA F451TC339161616-157.5 HOSE ASSY, 1, STR, SHT, 153
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50279
Description: HOSE ASSY, TONG VLV TO SPINNER BLKHD
Eng ID: 1
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50280
Description: HOSE ASSY, BLKHD TO SPINNER
Eng ID: 1
HOSE #34 1.00 EA F471TC66888-28.5 HOSE ASSY, 1/2, SWV STR, SWV STR, 25.5
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50281
Description: HOSE ASSY, PIVOT BEARINGS
Eng ID: 0
HOSE #38 1.00 EA P520N61424-15 HOSE ASSY, 1/4, SWV STR, NPT MALE, 13.5
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50282
Description: HOSE ASSY, QUICK COUPLERS
Eng ID: 1
HOSE #39 1.00 EA F721TC137161616-15.5 HOSE ASSY, 1, NPT MALE, 45° ELL, 12
HOSE #40 1.00 EA F451TC137161616-15.5 HOSE ASSY, 1, NPT MALE, 45° ELL, 12
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50283
Description: HOSE ASSY, UPPER TONG PLUMBING
Eng ID: 1
HOSE #41 1.00 EA F721TC66121212-18 HOSE ASSY, 3/4, SWV STR, SWV STR, 14.5
HOSE #44 1.00 EA F721TC639121212-25 HOSE ASSY, 3/4, SWV STR, 90° SHT, 21.5
HOSE #52L 1.00 EA P520N61424-16 HOSE ASSY, 1/4, SWV STR, NPT MALE, 14.5
HOSE #52R 1.00 EA P520N61424-30.5 HOSE ASSY, 1/4, SWV STR, NPT MALE, 29
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50284
Description: HOSE ASSY, LOWER TONG PLUMBING
Eng ID: 1
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50285
Description: HOSE ASSY, PURGE HOSES
Eng ID: 0
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50286
Description: HOSE ASSY, LIFT CYL HOSES
Eng ID: 0
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50430
Description: KIT, LABEL, ENG, ARM, TM120
Eng ID: 2
01 1.00 EA DT50236 LABEL, SAFETY, HIGH PRESSURE, ENG

02 4.00 EA DT50261 LABEL, EQUIPMENT, LIFT POINT, ENG
03 1.00 EA DT50263 LABEL, EQUIPMENT, TM CONTROL PANEL, ENG
04 1.00 EA 185200001 LABEL, EQUIPMENT, CARRIAGE CONTROL PANEL
05 3.00 EA DT50287 LABEL, EQUIPMENT, ARROW
06 3.00 EA DT50288 LABEL, SAFETY, PINCH POINT, 7 x 4.5, ENG
07 2.00 EA DT50289 LABEL, SAFETY, PINCH POINT, 4 x 5, ENG
08 2.00 EA DT50290 LABEL, SAFETY, PINCH POINT, 4 x 5, ENG
09 1.00 EA 184200009 S/N PLATE, WRENCH
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50472
Description: VLV SECTION, JAW CLAMPS, TM-120
Eng ID: 1
Drawing ID: AY50472 Rev No: DEV-02
01 1.00 EA E12367 COIL, DIR VLV

02 1.00 EA M10572 COVERS, HAWE SPR, SIZE 5
03 1.00 EA M10573 HDW, COVERS, HAWE SPR, SIZE 5
04 1.00 EA M11223 HOUSING, ELEC-HYD ACTUATOR, TM-120
05 1.00 EA M11224 LEVER, HAND, HAWE VLV BANK
06 1.00 EA S10087 SEAL KIT, SECTION, HAWE, 5 SER VLV
07 1.00 EA S10176 O-RING, 2IN x 2 1/8IN x 0.070IN
08 3.00 EA SH-M5-50MM-SS CAPSCR, HEX SOC HD, M5x50 A2-70, SS
Printed: 7/11/2008
1 8
4 5
7 3 2
NOTE:
PART #7 IS INCLUDED IN PART #6
ONLY ORDER PART #7 WHEN ORDERING REPLACMENT COVERS

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, JAW CLAMPS, TM-120
Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-02 CHANGED TO CORRECT SEAL KIT 3/7/2008 DATE CREATED: PART NO: REV:
DEV-01 RFM 2/25/2008 February 25, 2008 11:16:39 AM AY50472 DEV-02
Engineering
Bill of Material
Part: AY50473
Description: VLV SECTION, TONG TORQUE CYL, TM-120
Eng ID: 1

Printed: 7/11/2008
1 8
1 8
4 5
7 3 2
NOTE:

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, TONG TORQUE CYL, TM-120
Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-01 RFM 2/25/2008 February 22, 2008 4:20:02 PM AY50473 DEV-02
Engineering
Bill of Material
Part: AY50474
Description: VLV SECTION, SPINNER MOTOR, TM-120
Eng ID: 1

Printed: 7/11/2008
1 8
4 5
7 3 2
NOTE:

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, SPINNER MOTOR, TM-120
Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-01 RFM 2/25/2008 February 25, 2008 11:31:57 AM AY50474 DEV-02
Engineering
Bill of Material
Part: AY50475
Description: VLV SECTION, SPINNER CLAMP CYL, TM-120
Eng ID: 1

Printed: 7/11/2008
1 8
1 8
4 5
7 3 2
NOTE:

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION,SPINNER CLAMP CYL, TM-120
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-03 CHANGED TO CORRECT SEAL KIT 3/7/2008 DATE CREATED: PART NO: REV:
REL-02 RFM 2/25/2008 February 25, 2008 11:42:53 AM AY50475 REL-03
Engineering
Bill of Material
Part: AY50479
Description: VLV, INLET COMPLETE, 5 SERIES, TM-120
Eng ID: 0
01 1.00 EA S10123 SEAL KIT, INLET, HAWE, 5 SER VLV
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV INLET COMPLETE, 5 SERIES, TM-120
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-02 UPDATED ASSEMBLY COMPONENTS 2/25/2008 February 25, 2008 9:55:59 AM AY50479 REL-02
Engineering
Bill of Material
Part: AY50501
Description: SUBPLATE, INLET, 5 SERIES
Eng ID: 0
01 1.00 EA S10124 SEAL KIT, SUBPLATE, HAWE, 5 SER VLV
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SUBPLATE, INLET, 5 SERIES
Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-01 3/7/2008 March 07, 2008 12:40:51 PM AY50501 DEV-01
Engineering
Bill of Material
Part: AY50503
Description: SUBPLATE, VLV ASSY, 5/5
Eng ID: 0
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SUBPLATE, VLV ASSY, 5/5
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50504
Eng ID: 0
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE INLET SUBPLATE, VLV ASSY, 3/4
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50505
Eng ID: 0
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SUBPLATE, VLV ASSY, 3/4
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50506
Description: VLV, ARM CONTROL, WRENCH, 3 SERIES
Eng ID: 0
01 1.00 EA AY50504 SUBPLATE, VLV ASSY, 3/4

02 3.00 EA AY50505 SUBPLATE, VLV ASSY, 3/4
03 1.00 EA AY50507 VLV SECTION, ROTATE CONTROL, WRENCH
04 1.00 EA AY50508 VLV SECTION, VERT CONTROL, WRENCH
05 1.00 EA AY50509 VLV SECTION, HOR CONTROL, WRENCH
06 1.00 EA AY50510 VLV INLET, WRENCH ARM, 3 SERIES
07 1.00 EA H10578 END PLATE, VLV ASSY, #2 ORB, TM80
Printed: 7/11/2008
3 4 5
1 2

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV, ARM CONTROL, WRENCH, 3 SERIES
Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-01 RFM 3/10/2008 March 10, 2008 9:04:41 AM AY50506 DEV-01
Engineering
Bill of Material
Part: AY50507
Description: VLV SECTION, ROTATE CONTROL, WRENCH
Eng ID: 0

05 1.00 EA M11228 HOUSING, ELEC-HYD ACTUATOR
Printed: 7/11/2008
4 5
7 1
3 2

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, ROTATE CONTROL, WRENCH
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50508
Description: VLV SECTION, VERT CONTROL, WRENCH
Eng ID: 0

Printed: 7/11/2008
4 5
7 1
3 2 6

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, VERTICAL CONTROL, WRENCH
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50509
Description: VLV SECTION, HOR CONTROL, WRENCH
Eng ID: 0

Printed: 7/11/2008
4 5
7 1
3 2 6

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV SECTION, HORIZONTAL CONTROL, WRENCH
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50510
Description: VLV INLET, WRENCH ARM, 3 SERIES
Eng ID: 0
01 1.00 EA H10692 VLV, DIRECT RELIEF FOR SIZE 3 INLET

02 1.00 EA S10125 SEAL KIT, INLET, HAWE, 3 SER VLV
Printed: 7/11/2008
1

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE VLV INLET, WRENCH ARM, 3 SERIES
Bus. (403) 237-6400
Fax. (403) 233-2667
Engineering
Bill of Material
Part: AY50517
Description: SENSOR, LINEAR DISPLACEMENT, 450 STRK
Eng ID: 1
01 1.00 EA E12134 ROD END, SPHERICAL, 10mm

02 1.00 EA E12758 ENCODER, LINEAR TRANSDUCER CABLE
Printed: 7/11/2008
2

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE SENSOR, LINEAR DISPLACEMENT, 450 STRK
Bus. (403) 237-6400
Fax. (403) 233-2667
A RFM 4/1/2008 DATE CREATED: PART NO: REV:
REL-01 RFM 3/12/2008 March 12, 2008 2:12:15 PM AY50517 A
SUBSECTION 8B: HYDRAULIC POWER UNIT
Assembly Description Drawing Rev
112100002 POWER PACK, HPU COMPLETE 480 VAC 112100002 C

122100015 TANK, HYD, PWR PACK, 480/ 600VAC 122100015 A
183400001 PLUMBING SCHEMATIC, HPU, STD,STAND ALONE 183400001 DEV-01
AY50175 DRIVE CPLG ASSY, JAW, 50HP NO DRAWING 0

AY50287 ASSY, HYD, MOTOR & PUMP, 50HP, 480VAC AY50287 DEV-02
AY50466 VLV, TONG CONTROL, TM-120 AY50466 REL-03

Engineering
Bill of Material
Part: 112100002
Description: POWER PACK, HPU COMPLETE 480 VAC
Eng ID: 4
Drawing ID: 112100002 Rev No: C
01 0.00 EA AY50145 MAIN PANEL BOX

02 1.00 EA AY50147 ASSY, ELEC, HPU, STARTER PANEL, 480V
03 1.00 EA AY50554 KIT, HPU, 50 HP, 480 VAC, STD
04 1.00 EA N10335 PURGE KIT, MAX ENCLOSURE VOL 90 CUBIC FT
05 1.00 EA N10336 VENT, PURGE SYSTEM, 1-1/4IN MYERS HUB
09 1.00 EA E12454 HUB, MYERS, 2IN
10 1.00 EA E13485 REDUCER, MALE 2 NPT, FEM 1 NPT, STEEL
11 9.00 EA E12467 LUG, COMP, #10-8
Printed: 7/11/2008
1
6 7 7 8
PLC BOX HDW

4 PL
4
2
8 7 7 6
STARTER BOX HDW

4 PL
9 10
SIDE PANEL REMOVED
NOTE: ITEM #11 LOCATED INSIDE MOTOR JUNCTION BOX

REV. DESCRIPTION DATE THE DRAWINGS, INFORMATION AND SUBJECT MATTER

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE POWER PACK, HPU, 50HP, 480 VAC
C NOW REFERENCES HPU UNIT AS VSA 4/10/2008 Calgary, Alberta, Canada, T2C 4L6 PROPERTY OF CANRIG DRILLING TECHNOLOGY CANADA
B UPDATED DESCRIPTION, MOVED PURGE VENT TO CONTACTOR BOX 4/3/2008 Fax. (403) 233-2667
A ADDED HYD COMPONENTS, ADDED TORQUE SPECS 3/20/2008 April 10, 2006 11:07:48 AM 112100002 C
Engineering
Bill of Material
Part: 122100015
Description: TANK, HYD, PWR PACK, 480/ 600VAC
Eng ID: 2
01 1.00 EA 131100949 HYD TANK, POWER PACK

02 1.00 EA 131100950 HYD TANK LID, POWER PACK
03 1.00 EA 141101957 FILTER FLANGE, POWER PACK
04 1.00 EA 141101958 HYD TANK BAFFLE
05 2.00 EA 149900003 FLANGE GASKET, DUAL HPU
06 1.00 EA 149900004 TANK LID GASKET, POWER PACK
07 3.00 EA 152100041 TUBE, RETURN LINE PUMP CASE
08 1.00 EA H10308 FILTER ELEMENT, 10 MICRON, 10C, 50AT
09 1.00 EA H10311 FILTER, CASE, 3/4IN NPTF, 3/4IN SPIN ON
10 1.00 EA H10546 PLUG, PIPE, 0.5 IN NPT
11 1.00 EA H10597 NIPPLE, PUMP, 2 1/2IN NPT, CLOSE SUCTION
12 1.00 EA H10598 VLV, BALL 2 1/2 IN NPT, FULL FLOW
13 1.00 EA H10599 NIPPLE, KING, PIPE 2 1/2IN, HOSE 3IN
14 1.00 EA H10697 FILTER, RET, 80 GPM
17 1.00 EA H15-070120-16-20 ADPT, MALE 1 JIC, MALE 1-1/4 ORB
18 1.00 EA H15-3222-12 UNION, MALE 3/4 NPT, MALE 3/4 NPT
19 1.00 EA H15-070202-12-12 ELL 90°, MALE 3/4 JIC, MALE 3/4 NPT
20 1.00 EA N10295 GAUGE, 10IN VISUAL W/ELEC SW, 24VDC
21 1.00 EA N10296 GAUGE, TEMP LEVEL IND
22 1.00 EA N10299 THERMOWELL, TEMP, 2.5 INSERTION, 4 STEM
23 1.00 EA N10301 TRANSMITTER, TANK, -60 TO 200C
30 1.00 EA H15-070112-08 CAP, 1/2 JIC
31 1.00 EA H10406 PLUG, RESERVOIR, 2.0 NPT
Printed: 7/11/2008
14 8
17
26 25 24
27 29 28 4
15
30
19
20
22 11
15 31
23 10
18
12
21
13

REV. DESCRIPTION DATE 7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE HYDRAULIC TANK, PWR PACK, 480/600 VAC
A MOVED HEATER TO COLD WEATHER KIT, ADDED#8 JIC CAP, ADDED 2IN 4/2/2008 Website: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
NPT PLUG Bus. (403) 237-6400
Fax. (403) 233-2667
DEV-04 UPDATED DRAWING FOR CLARITY 11/14/2007 WITHOUT WRITTEN CONSENT OR DIRECTION.
DEV-03 ADDED HYD. FITTINGS 11/8/2007 October 16, 2007 12:57:59 PM 122100015 A
Engineering
Bill of Material
Part: 183400001
Description: PLUMBING SCHEMATIC, HPU, STD,STAND ALONE
Eng ID: 0
01 1.00 EA AY50465 HPU-STD UNIT
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50175
Description: DRIVE CPLG ASSY, JAW, 50HP
Eng ID: 0
01 1.00 EA M11010 CPLG, DRIVE, HUB, 50HP, 1.75 B, 7/16 KEY

02 1.00 EA M11011 CPLG, DRIVE, INSERT, 50HP
03 1.00 EA M11012 CPLG, DRIVE, HUB, 2.125 BORE, 1/2 KEY
04 1.00 EA M11013 CPLG, DRIVE, INSERT RING
Printed: 7/11/2008
Engineering
Bill of Material
Part: AY50287
Description: ASSY, HYD, MOTOR & PUMP, 50HP, 480VAC
Eng ID: 0
01 1.00 EA 161900001 ADPT, PUMP-MOTOR, W/ HOLES

02 1.00 EA E12113 MOTOR, LH, 50HP/460VAC 324TC-TEFC
03 1.00 EA H10312 PUMP, PISTON, 145cc, RRW, 5000PSI
04 1.00 EA AY50161 FLANGE KIT, 1-1/4IN, CODE 62
05 1.00 EA H10409 CPLG, HYD, 3/8 NPT, 3000 PSI
06 1.00 EA H10425 ADPT, SUC AND RET, 90°, 150 PSI
07 1.00 EA H10490 VLV, HYD, CHECK, 1-1/4 IN, SAE 62
08 1.00 EA H10536 SPLIT FLANGE, 37° FLARE, H PRESS, 62
09 1.00 EA AY50419 FLANGE KIT, SAE, SPLIT, 2 1/2IN, CODE 61
12 1.00 EA H15-070432-16-16 TEE, FEM SWV RUN 1" JIC, MALE 1" JIC
14 4.00 EA HH-0500NC-0400-GR5 CAPSCR, HEX HD, 1/2-13UNC, x 4.00, GR5
Printed: 7/11/2008
12
2
17 14
4
11
10
5
16 19
15 19
18 17 13

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE HYDRAULIC POWER PACK, 480 VAC
REV. DESCRIPTION DATE Website: www.canrig.com LTD, AND ARE NOT TO BE COPIED, REPRODUCED OR USED
DEV-02 ADDED HYD FITTINGS, BOM NO. 17, 18, 19 11/7/2007 Fax. (403) 233-2667
DEV-01 RFM 10/18/2007 April 26, 2006 10:40:09 AM AY50287 DEV-02
Engineering
Bill of Material
Part: AY50466
Description: VLV, TONG CONTROL, TM-120
Eng ID: 1
01 2.00 EA AY50472 VLV SECTION, JAW CLAMPS, TM-120

02 1.00 EA AY50473 VLV SECTION, TONG TORQUE CYL, TM-120
03 1.00 EA AY50474 VLV SECTION, SPINNER MOTOR, TM-120
04 1.00 EA AY50475 VLV SECTION, SPINNER CLAMP CYL, TM-120
05 1.00 EA AY50479 VLV, INLET COMPLETE, 5 SERIES, TM-120
06 1.00 EA AY50501 SUBPLATE, INLET
07 5.00 EA AY50503 SUBPLATE, VLV ASSY
08 1.00 EA H10650 END PLATE, VLV ASSY, TM80/120
Printed: 7/11/2008
2 1 3 4

7475 51 Street SE
HEREOF ARE THE CONFIDENTIAL, SOLE AND EXCLUSIVE TM120, TONG CONTOL VLV
Bus. (403) 237-6400
Fax. (403) 233-2667
REL-03 ADDED SUBPLATES TO VSA 3/7/2008 DATE CREATED: PART NO: REV:
REL-02 UPDATED VALVE BANK BREAKDOWN 2/25/2008 February 25, 2008 11:51:49 AM AY50466 REL-03

Torq-Matic Canrig Sec-08 Part List

Uploaded by

Copyright:

Available Formats

Torq-Matic Canrig Sec-08 Part List

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Torq-Matic Canrig Sec-08 Part List

Uploaded by

Copyright:

Available Formats

MODEL TM120 TORQ-MATIC FLOOR WRENCH

CANDOC TM120 MANUAL COPYRIGHT © 2004 CANRIG DRILLING TECHNOLOGY LTD.

Printed in the United States of America

Assembly Description Drawing Rev

102200003 ASSY, WRENCH, TM-120 SERIES, ARM, LONG 102200003 DEV-11

AY50145 ASSY, ELEC, MAIN PANEL BOX, WRENCH AY50145 REL-03

AY50146 ASSY, ELEC, DRILLERS CONSOLE, WRENCH AY50146 REL-02

AY50147 ASSY, ELEC, HPU, STARTER PANEL, 480V AY50147 REL-02

AY50148 ASSY, ELEC, ARM BOX, WRENCH AY50148 REL-02

AY50149 ASSY, ELEC, TONG BOX, TM120 AY50149 REL-01

Thursday, July 10, 2008 Serial Number TM80-069

Thursday, July 10, 2008 Serial Number TM80-069

01 1.00 EA 112100001 TM120 TORQUE ASSY

01 4.00 EA 122100003 JAW ASSEMBLY

SECTION A-A DETAIL B

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA 122200010 BULKHEAD MOUNT ASSEMBLY

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 2.00 EA 122300009 ASSEMBLY, VERTICAL LIFT, WRENCH ARM

DETAIL A SECTION B-B

CREATED: January 08, 2007 5:10:38 PM PART NO: 112300002 REV. A

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA 131100184 RAM JAW

ASSEMBLE ONE LEFT/ONE RIGHT

01 1.00 EA 161900001 ADPT, PUMP-MOTOR, W/ HOLES

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA 131100493 LOWER TONG FRAME

01 1.00 EA 122200007 SPINNER TRACK V MOUNT

01 1.00 EA 131100123 JEEP BED

01 1.00 EA 131100124 SPINNER JEEP FRAME

01 1.00 EA 141100439 PLATE, SPINNER ASSY HYD. BULKHEAD

01 1.00 EA 131100466 ROLLER FRAME

01 1.00 EA 122200012 ROLLER FRAME

01 1.00 EA 131100275 VERTICAL LIFT PROFILE

15 USE 4 FW AS SPACERS TO CENTER CYL

01 1.00 EA 131100385 BOTTOM PLATE ASSEMBLY

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA AY50275 HOSE ASSY, WRENCH ARM

01 1.00 EA AY50506 VLV, ARM CONTROL, WRENCH, 3 SERIES

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 108.50 IN M11136 CHAIN, BULK, 1/2IN x 65IN, BLUE

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA AY50145 MAIN PANEL BOX

01 1.00 EA 158100047 ENCLOSURE, 4 x 24H x 24W x 12D

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA 158100048 PANEL, CUSTOM, 4X, 435H x 385W x 135D

THE DRAWINGS, INFORMATION AND SUBJECT MATTER

01 1.00 EA 158100049 ENCLOSURE, CSA 4X, 24H x 16W x 80

CANRIG DRILLING TECHNOLOGY CANADA LIMITED © 2006