instruction manual

SL Mobile LED 135

LeyardTVF 5x5
 CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

WARNING: To reduce the risk of electric shock, do not remove cover.

No user-serviceable parts inside. Refer servicing to qualified service personnel.

To reduce the risk of fire or electric shock, do not expose this apparatus
to rain or moisture.

Dangerous high voltages are present inside the enclosure.

Do not open the apparatus. Refer servicing to qualified personnel.

Do not place containers with water above the apparatus (including on

shelves above, etc.).

About safety symbols

Various symbols are used in these operating instructions to ensure safe use, and to
protect you and others against the risk of injury and against material damage. The
meaning of each of the symbols is explained below.

This symbol indicates information that, if ignored or applied

incorrectly, creates the risk of death or serious personal injury.

This symbol indicates information that, if ignored or applied

incorrectly, could possibly create the risk of death or serious
personal injury.

This symbol indicates information that, if ignored or applied

incorrectly, creates the risk of personal injury or material
damage.
MediaScreen GmbH SL Mobile LED 135 1

Table of contents

1. Safety precautions.......................................................................... 2

2. Introduction ..................................................................................... 3

3. System components ....................................................................... 4

4. Operation of the ScreenLifter ...................................................... 5

4.1 Features and characteristics of the control unit................ 5

4.2 Unloading the ScreenLifter from the transport case.......... 6

4.3 Loading the ScreenLifter into the transport case .............. 8

4.4 Use of the Rollerboard........................................................... 9

4.5 Lifting and lowering the display........................................... 9

5. Dismouting / Mounting the display on the ScreenLifter.............. 10

6. Appendix ......................................................................................... 13

6.1 Technical Data....................................................................... 13

6.2 System dimensions................................................................. 14

6.3 Environmental conditions...................................................... 15

6.4 Loading with lifting platform................................................ 15

6.5 End position adjustment of the lifting columns .................. 16

6.6 Troubleshooting ..................................................................... 17

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 2

1. Safety instructions
These safety precautions must be observed minutely!
Inappropriate operation of the system may cause material damage
possibly causing harm to the operator abd bystanders!

• Carefully read the operating instructions and safety precautions before first set-up.

• Keep the operating instructions for later reference.

• Make sure the local power supply meets the requirements of the ScreenLifter (check
type label) before operating the system!

• Manipulation or replacement of any system components may only be carried out by

qualified technical personnel approved by the manufacturer or its distributors.

• In case of malfunctions of the ScreenLifter (emission of fumes, unusual noise, etc.) shut
off all system components and disconnect all power connections. A moderate smell of
oil during lifting or lowering of the screen is caused by warming of the lubricants applied
to the mechanical parts of the lifting mechanism, and is not a sign of malfunction

• The ScreenLifter may not be operated in a potentially explosive atmosphere.

• Do not operate the ScreenLifter outdoors. The ScreenLifter may be operated in a dry
environment only.

• The maximum weight of the ScreenLifter system (ScreenLifter plus transport case) includ-
ing a display is approx. 650 kg / 1433 lb*. When setting up the ScreenLifter, consider the
loadcarrying capacity and condition of the surface, particularly of stages or other non-
permanent constructions.

• Only set up the ScreenLifter on a flat and level surface!

• When moving the screen up, down or rotating, it must be ensured that no objects,
cables or body parts are pinched in.

• Different types of display require different corresponding adapter frames. Do not mount
a display if you are not in possession of the dedicated adapter frame.

• When opening the transport case, never open the clasps on both lids at the same time.
Doing so may cause one lid to fall while lifting off the other.

• The removed case lids must be secured against tipping over. It is best to place them
next to each other on the floor, and to close the four clasps that connect the two lids.

• Check all bolted connections before operating the ScreenLifter.

• If you detect parts bent or otherwise damaged, the ScreenLifter must not be operated
any longer.

• Never try to carry out repairs of the ScreenLifter! The Screenlifter may only be serviced
by the manufacturer, or trained technicians approved by the manufacturer or its dis-
tributors.

• The maximum duration of continuous operation of the lifting mechanism of 2 minutes

ON (see type label) must never be exceeded!

• If there is an increased requirement for stability (in case of trade fairs, places frequented
by the public, etc.) or if you want to move the lower edge of the display over 130cm,
mount the extensions are provided in order to increase the base area of the Screen-
Lifter.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 3

2. Introduction
The ScreenLifter system is an integrated storage, transport, and support solution for large-
format screens (Plasma, TFT, etc.), substiantially reducing manual labor during transport and
installation.
Once you have attached the display, the ScreenLifter system takes care of transporting,
positioning, lifting and lowering your display. With the ScreenLifter you can even rotate your
Display into potrait orientation.
The lifting mechanism of the ScreenLifter is not designed for continous operation exceeding
the duty cycle of 2 minutes ON/18 minutes OFF.

Accessories
Check if you have received these accessories:

Main cable Manual Remote

Bedienungsanleitung

ScreenLifter 85-LITE
für Panasonic TH-85PF Plasma Display

Deutsch - Betriebsanleitung - MediaScreen GmbH

Bitte lesen Sie diese Betriebsanleitung bevor Sie den ScreenLifter in Betrieb nehmen.
Bitte bewahren Sie diese Betriebsanleitung sorgfältig auf.

Optional:

Base Enlargement Fixing angle Rollerboard

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 4

3. System components

1 Screenlifting Base 10 Power connection

2 Lifting columns 11 Connection remote control
3 Column bracket 12 Lifting column runner
4 Suspension tabs 13 Nameplate
5 Gas spring 14 Extension of the stand
6 Distribbution box 15 Connection sockets HDMI, USB, CAT
7 Rotary lock 16 Antenna WiFi
8 Power connection LED modules 17 Fixing angle
9 ON/OFF switch 18 Display recording

6 7

16
4 4 15

5 5
3
8 7

12 12
2

13

14 1 14

14 14

17 17

6 7

16
18 15 18

8 7

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 5

4. Operating the ScreenLifter

4.1 Features and funtion of the control unit
The ScreenLifter is operated via a wired remote control. The connection socket for the re-
mote control is located on the bck of the base plate.

During operation, the running time of the motors is recorded by the controller to protect
against overheating. The controller switches off the motors after continuous operation of
max. 2 minutes. In this case, wait 18 minutes. After the cooling time, you can put the lifting
mechanism back into operation.

In rare cases, a vertical offset may occur between the rotors of the two lifting columns
during operation. As long as the ScreenLifter is connected to the power supply, a possible
offset is detected by the control unit and automatically corrected. However, if an offset
occurs while the ScreenLifter is disconnected from the power supply, e.g during storage or
transport, a reset mustt be performed (see 6.3.).

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 6

4.2 Unloading the ScreenLifter from the transport case

1. Remove the covers of the transport case. Secure the lids against falling over by placing
them next to each other and closing the top of the lids.

1.

2. Slide the ScreenLifter with the rolling board

to the desired location and remove the
small slide-in board on the back of the
base plate.

1.
2.

3. Connect the power cable to the power

supply of the ScreenLifter (230V/50Hz)
and switch it on. The display shows "15".

1.
2.
3.
4. Press and hold the "2" button on the re-
mote control to lower the base plate and
lift the column frame off the holder. Raise
the screen until there is enough space be-
tween the bottom edge of the display and
the case.

© MediaScreen GmbH
1.
MediaScreen
2. GmbH SL Mobile LED 135 7
3.
4.
5. Pull the rolling board forward out from under the screen.

1.
2.
3.
4.
5. Ziehen Sie das Rollbrett nach vorne unter dem Bildschirm hervor.

6. Mounting the extensions.

For increased safety requirements, such as trade shows or areas with public traffic, you
should increase the footprint of the ScreenLifter using the extension plates.

We also recommend mounting the plates if the bottom edge of the display is to be moved
over 120 cm. The indication in the display of the remote control shows approximately the
height of the lower edge of the picture.
The plates are stored in the case and are screwed to the base plate using the M8 screws
provided.
If the ScreenLifter is to be placed in front of a wall, only the two front panels can be mount-
ed.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 8

4.3 Loading the ScreenLifter into the transport case

1. If necessary, disassemble the extensions before loading the ScreenLifter into the trans-
port case.
2. Press and hold the "2" button to move the screen to the correct height for loading into the
transport case. The motors stop when "60" appears in the display.
3. Push the roller board from the front to the stop under the screen. Make sure that no pro-
truding parts or other objects in the case damage the display. Hold the roller board in
position.

4. Press and hold the "1" button to lower the screen onto the support and lift the Screen-
Lifter base plate off the surface. The motors stop automatically when the base is com-
pletely retracted.
5. Turn off the ScreenLifter and disconnect the remote control. Disconnect the power sup-
ply and insert the small slide-in board. The ScreenLifter is now securely anchored to the
rolling board and ready for transport.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 9

4.4 Use of the Rollerboard

In order to move the LED wall quickly and safely from A to B in closed buildings, we offer
a rolling board as an accessory, which is smaller and more maneuverable than the large
case for truck transport. Be especially careful when using the rolling board, as the LED wall
on it is unprotected against impacts and collisions with objects. When you want to park
the LED wall, apply the two brakes on the back of the roller board to prevent it from mov-
ing unintentionally.

- ATTENTION-

Do not forget to unscrew the extensions before loading the LED-Lifter

onto the roller board.

FALSE CORRECT

To load the roller board, follow steps 1 to 5 from chapter 4.3, to remove the roller board
follow steps 2 to 5 from chapter 4.2

4.5 Raising and lowering the screen

When operating the ScreenLifter, make sure there is sufficient distance to other objects,
ceilings,persons, etc.
The maximum continuous operating time of the lifting mechanism of 2 minutes must under
no circumstances be exceeded! Before restarting the lifting mechnism, allow it to cool
down for 18 minutes.
Use the "1" and "4" buttons to adjust the screen height according to your preferen-
ces.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 10

5. Dismounting/Mounting the Display on the ScreenLifter

For the disassembly/assembly of the LED

wall, you will need the two fixing angles
and 4 M8x16 screws from the ScreenLifter
accessories.

Mount the two fixing angles on the back

to the upper edge of the LED wall. Suit-
able sliding blocks are located in the
horizontal profiles for mounting. Do not
use screws longer than max. M8 x 18. The
brackets cannot be fastened securely
with screws that are too long.

8 cm

The weight of the LED wall is about 250

kg. To lift it out of the lugs, you need load
loops or chain hoists that you attach to
the eyebolts. First, lift the LED wall 8 cm
upwards until all four display holders are
above the lugs.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 11

20 cm

Then move the wall forward at least 20

cm to get the electrical box in front of the
column frame. You can then pull the wall
upwards and stow the ScreenLifter in the
case.

To mount the LED wall on the ScreenLifter, proceed in reverse order. First, bring the display
to the correct height (Alternatively, you can also adjust the height of the column frame
with the remote control of the ScreenLifter when you connect the lifter to the power sup-
ply).
Then move the display in the direction of the column frame until the four display holders
are located above the tabs. Now lower the LED wall and make sure that the grooves in
the display holders slide into the tabs. To simplify threading, the two lower tabs are lon-
ger than the upper tabs and will therefore engage first. When correctly mounted, all four
tabs are in the grooves of the display holders and the LED wall hangs horizontally on the
ScreenLifter.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 12

Leyard TVF 5x5

Modules

Frame

SL MobileLED with frame

SL MobileLED with modules

If you mount the modules yourself, it is very important to have the correct position of the bot-
tom edge of the modules.If they hang too high, the case lids cannot be closed and if they
hang too low, there is a risk that they will be damaged when they are loaded into the case
or transported in the case.
The correct height of the bottom edge of the modules is 23 mm above the lower edge of
the column bracket, as seen in the drawing above. The deviation should not be more than
+/-3 mm.
If you have any questions about mounting the modules, contact the manufacturer.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 13

6. Appendix
6.1 Technical Data

ScreenLifter
Dimensions compare with depiction on page 13, 14, 15
Weight (w/o display) 193 kg
Color aluminium: anodized EV 1, steel: RAL 9011
Lift range 1360 mm
Lift speed 15 mm/s
Insulation class lifting columns E
Protection rating lifting columns IP 42
Power source 230 V AC / 50 Hz
Input standby (w/o display) 2-5 W
Rated input (w/o display) 400 W (bei 230V AC)
Maximum input (w/o display) 900 W (bei 230V AC)
Operating temperature +5°C bis +45°C
Storing temperature -20°C bis +60°C
Operating humidity 5 %–85 % (non condensing)
Limit switches mechanical, upper and lower position
IEC protection class I
Schwitching capacity 10% ( 2 min. ON / 18 min. OFF )
Max. allowed weight Screen 250 kg
Max. display weight Separate power supply

Transportcase
Dimensions (W x H x D) 3136 mm x 1999 mm x 822 mm
Weight 290 kg
Wheels 8 swivel casters (4 with brakes)
Available colors black, grey, blue

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 14

6.2 Dimensions

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 15

6.3 Environmental conditions

Transport & Storage Operation

Temperature -20°C to +45°C +4°C to +40°C
Humidity Dry, covered in case 10% to 80% without condensation

Installation site Not outdoors, covered in Not outdoors, horizontal, solid sub-
case strate, not in explosive atmosphere

6.4 Loading with lifting platform

As described in pictures 1-3, the case can be loaded into a 7.5 ton truck without other
aids, such as forklifts, etc., due to the special arrangement of the castors. The lifting plat-
form should be at least 180cm long.
For safety reasons, loading and unloading should be carried out by at least three people.
One person operates the lifting platform, the other two secure the case.
Please also note the max. lifting capacity of the lifting platform. Depending on the equip-
ment, the case with ScreenLifter can weigh up to 670kg. When lifting and lowering the
platform, the case should therefore always be as close as possible to the truck.

Bild 1 Bild 2 Bild 3

Ladebordwand 7,5 to Ladebordwand 7,5 to Ladebordwand 7,5 to

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 16

6.5 End position adjustment of the lifting columns

In rare cases, a vertical offset may occur between the sliders of the two lifting columns. As
long as the ScreenLifter is connected to the power supply, a possible misalignment is de-
tected by the control unit and automatically corrected. However, if an offset of the sliders
occurs while the ScreenLifter is disconnected from the power supply, e.g. during storage
or transport, a manual end position adjustment must be performed.

If possible, the end position adjustment should be performed without the screen mounted.

Please read the following three steps before performing the end position adjustment! In
any case, carry out all three steps of this manual!

Perform end position adjustment:

1. Press and hold the "RESET" button on the remote control — both sliders start to
move downwards. If one of the two sliders is already in its lower end position, nothing
will apparently happen. Nevertheless, keep pressing the " RESET" button until you
hear a click.
2. As soon as the lower of the two rotors reaches its end position, both motors switch off
and you hear a clicking sound from the control unit. This is not yet the end position
adjustment!
3. Release the " RESET" button and press and hold it again. Keep it pressed until the
upper slider also starts to move downwards (it can take up to 20 seconds until this
happens) and finally reaches its lower end position. As soon as it has also reached its
lower end position, the motor switches off and you hear a click again. The end posi-
tion adjustment is now done and the ScreenLifter is ready for use again.

© MediaScreen GmbH
MediaScreen GmbH SL Mobile LED 135 17

6.6 Troubleshooting
Problem: ScreenLifter does not respond to remote control inputs.

Possible Cause(s): Insufficient power supply - check if the existing power supply
meets the requirements of the ScreenLifter (section 6.1 Technical
data). Netzanschlusskabel nicht korrekt eingesteckt — überprüfen
Sie die Verbindung.

Possibly the remote control cable is not plugged in correctly - check

the plug connection.

Power cord/remote control faulty/defective - replace the faulty part

or contact the manufacturer.

Control unit defective - contact the manufacturer.

Problem: The screen can only be moved either up or down.

Possible Cause(s): Remote control defect — contact the manufacturer.

Control unit defect — contact the manufacturer.

Problem: ScreenLifter drives only in small steps.

Possible Cause(s): Mechanical distortion due to vertical misalignment between the ro-
tors leads to overload shutdown - check for vertical misalignment
and perform end position adjustment if necessary (see section 6.3).

The ScreenLifter stands on uneven or inclined ground. The changed

load conditions lead to an overload shutdown for safety reasons -
ensure that you have a sufficient base.

Control unit defect — contact the manufacturer.

© MediaScreen GmbH
 Contact

www.mediascreen.de

Tel: +49 89 697 994 60

Fax: +49 89 687 994 70
E-mail: [email protected]

MediaScreen Bildkommunikation GmbH

Fraunhoferstraße 4
D-82152 Planegg-Martinsried

v3.3
Errors and misprints excepted.
We reserve the right to make changes that serve the
further development of the product.
© 03/22 MediaScreen Bildkommunikation GmbH.