Scribd Logo
Upload

Welcome to Scribd!

  • 38 views

    Lenze AC Tech SMV Quick Start Guide

    Uploaded by

    AbdulSattar
    This document provides instructions for setting up an SMV variable frequency drive. It includes: 1. Information on setting input voltage selection and frequency control wiring based on mains voltage. 2. Details on configuring digital input logic control wiring for positive or negative logic using switches and parameter P120. 3. Instructions for setting relay terminal wiring using parameter P140 to define contact states. 4. Guidance on setting common parameters like P100 for start control source, P101 for standard reference source, P102-P105 for frequency and acceleration/deceleration times. 5. An overview of operating modes in parameter P300 and requirements for vector speed and torque control setup if using modes 4

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Lenze AC Tech SMV Quick Start Guide

    Uploaded by

    AbdulSattar
    38 views2 pages
    This document provides instructions for setting up an SMV variable frequency drive. It includes: 1. Information on setting input voltage selection and frequency control wiring based on mains voltage. 2. Details on configuring digital input logic control wiring for positive or negative logic using switches and parameter P120. 3. Instructions for setting relay terminal wiring using parameter P140 to define contact states. 4. Guidance on setting common parameters like P100 for start control source, P101 for standard reference source, P102-P105 for frequency and acceleration/deceleration times. 5. An overview of operating modes in parameter P300 and requirements for vector speed and torque control setup if using modes 4

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for setting up an SMV variable frequency drive. It includes: 1. Information on setting input voltage selection and frequency control wiring based on mains voltage. 2. Details on configuring digital input logic control wiring for positive or negative logic using switches and parameter P120. 3. Instructions for setting relay terminal wiring using parameter P140 to define contact states. 4. Guidance on setting common parameters like P100 for start control source, P101 for standard reference source, P102-P105 for frequency and acceleration/deceleration times. 5. An overview of operating modes in parameter P300 and requirements for vector speed and torque control setup if using modes 4

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    38 views2 pages

    Lenze AC Tech SMV Quick Start Guide

    Uploaded by

    AbdulSattar
    This document provides instructions for setting up an SMV variable frequency drive. It includes: 1. Information on setting input voltage selection and frequency control wiring based on mains voltage. 2. Details on configuring digital input logic control wiring for positive or negative logic using switches and parameter P120. 3. Instructions for setting relay terminal wiring using parameter P140 to define contact states. 4. Guidance on setting common parameters like P100 for start control source, P101 for standard reference source, P102-P105 for frequency and acceleration/deceleration times. 5. An overview of operating modes in parameter P300 and requirements for vector speed and torque control setup if using modes 4

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    SMV Quick Set-Up Card

    Input Voltage Selection


    Always check this parameter at first power up, set to a value based on mains voltage
    P107 = “0” for mains voltage = 120,200,400,480 (VAC)
    P107 = “1” (Default) for mains voltage = 120,240,480,600 (VAC)

    Frequency Control Wiring


    Internal Voltage Control Com A in +10v
    2 5 6
    P100 = 0, 1, 2, 4 or 5
    P101 = 1
    2k – 10k

    External Voltage Control Com A in


    2 5
    P100 = 0, 1, 2, 4 or 5
    P101 = 1 for 0 -10V input External Speed
    Ref Common
    External Speed
    Ref Voltage

    Current Source Speed Control


    Com A in
    P100 = 0, 1, 2, 4 or 5
    P101 = 2 for 4-20mA input 2 25
    P163 (TB-25 current loss action) External External
    0 = No action Current Current
    Ref (-ve) Ref (+ve)
    1 = “F.FoL” fault message when input is less than 2mA
    2 = Go to Preset Speed

    Digital Input Logic Control Wiring


    The digital inputs can be configured for positive logic or negative logic,
    by setting switch (ALsw) (see picture opposite)
    P120 must also be set to match the configuration.
    P120 = “1” (Negative logic/Active low/NPN)
    P120 = “2” (Positive logic/Active High/PNP) (Default)
    (Incorrect setting will result in “F.AL” fault message)

    TB-1 = Drive Start/Stop (note that P100 must be set to 1,4 or 5)


    TB-13A = Configured using P121 (Default = 0 : No function)
    Start +15V/0V* D1 D2 D3
    TB-13B = Configured using P122 (Default = 0 : No function)
    1 4 13A 13B 13C
    TB-13C = Configured using P123 (Default = 0 : No function)
    10 = Rev rotation 11 = Start fwd 12 = Start rev
    13 = Run fwd 14 = Run rev 15 = Jog fwd
    16 = Jog rev 17 = Accel/Decel 2 18 = DC brake *Dependant on logic selected - Negative/Positive
    19 = Aux ramp to stop 20 = Clear fault 21 = Ext fault
    22 = Inverse Ext fault (0 to 9-Please refer to operating instructions)

    Relay Terminal Wiring


    Relay contact state when :
    P140 = 0 (Always Open)
    P140 = 1 (Closed = drive running) Internal Drive Relay
    P140 = 2 (Closed = drive running in reverse) Contacts
    P140 = 3 (Open = drive tripped)
    P140 = 4 (Closed = drive tripped)
    P140 = 5 (Open = restart attempts failed if P110 =3 to 6)
    P140 = 6 (Closed = output frequency =commanded frequency) 16 17
    P140 = 7 (Closed = output frequency is >P136)
    P140 = 8 (Closed = motor current = P171)
    To External
    P140 = 9 (Closed = 4-20mA signal is below 2mA) Device
    P140 = 10 (Closed = motor load is below P145)
    P140 = 11 through to 22 (Please refer to operating instructions)

    UK
    SMV Quick Set-Up Card
    Parameter Settings:
    P100: Start Control Source (Default = ‘0’)
    0 = Local keypad : Run button on front of drive
    1 = Terminal strip : Terminal strip start/stop circuit

    P101: Standard reference source (Default = ‘0’)


    0 = Keypad (local or remote) : Speed/torque reference from keypad buttons
    1 or 2 : See “Frequency Control Wiring” section.
    3 = Preset #1 : Speed/torque reference = Preset #1*
    4 = Preset #2 : Speed/torque reference = Preset #2*
    5 = Preset #3 : Speed/torque reference = Preset #3*
    6 = Network : Speed/torque reference from network*
    *Only if no Auto reference is selected using digital inputs

    P102 : Minimum Output Frequency (Default = ‘0Hz’)


    Set to minimum Frequency for Application

    P103 : Maximum Output Frequency (Default = ‘60Hz’) P103


    Set to Maximum Frequency for Application
    Hz P104 P105
    P104 : Acceleration Time (Default = ‘20s’)
    Set to required Acceleration Time P102 P102

    P105 : Deceleration Time (Default = ‘20s’)


    Set to required Deceleration Time t

    P108 : Motor overload protection (Default ‘100%’)


    Calculate P108 = (motor rated current / SMV output current rating) x 100

    P300: Operating Mode (Default = ‘0’)


    0 = Constant V/Hz Constant torque V/Hz, for general applications
    1 = Variable V/Hz Variable torque V/Hz, for centrifugal fan and pump applications
    2 = Enhanced Constant V/Hz-

    For single or multiple motor applications that require better


    performance than settings 0 or 1 but cannot use vector
    mode as no motor data is available or vector mode causing
    motor instability.

    3 = Enhanced Variable V/Hz-


    4 = Vector Speed Single motor applications requiring high starting torque and speed
    regulation
    5 – Vector Torque Single motor applications requiring torque control independent
    of speed

    Vector speed and torque control setup (P300 = 4 or 5)

    If P300 = 4 or 5, a motor auto-calibration must be carried out, ensure motor nameplate data is programmed
    first (detailed below), failure to do so will result in a F.n ld fault message.

    P302 = Motor rated voltage


    P303 = Motor rated current
    P304 = Motor rated frequency
    P305 = Motor rated speed
    P306 = Motor Cosine Phi
    Set P399 to 1 to start the motor auto-calibration, the display will show “CAL” for a short period of time and
    then “StoP” once completed. rev A

    UK

    www.Lenze-ACTech.eu

    You might also like