Phy1Lab Exp. 6

Physics 1 Lab | Expt.
# 6
Experiment No. 6:
(a) Study of Ohm’s law using unknown resistances.
(b) Determination of the equivalent resistances for series and parallel combinations of
resistors.
6.1 Objectives
The main objective of this lab is to design circuits with different combinations of unknown resistances to verify the
Ohm’s law and determine the equivalent resistances for series and parallel combinations of resistors.
6.2 Prelab
Student must have clear idea about the objectives and related theory of the experiment. Lab Demonstrator will confirm
that the students have submitted their previous group lab reports in printed form before giving them the attendance. The
marks of performance depend greatly on this part.
6.3 Outcomes
After completing this lab work student will be able to answer the following questions:
• What is the Ohm’s law? How Ohm’s law looks in a graph? How unknown resistance can be
determined from the graph?
• How to construct series and parallel combinations of resistors and how the equivalent
resistances can be calculated?
• For all possible combinations of resistors, how to plot voltage versus current graph and find
the slop of best fitted lines to determine the unknown resistances?
6.4 Timing and Lab Activities (Total 3 Hours)

• Lab Preparation (15 minutes):
▪ For attendance and equipment distribution among the groups.
• Lecture on Theory (40 minutes):
▪ The teacher will clarify the objective and theory of the experiment.
• Lecture on Procedure 30 minutes):
▪ Demonstrator will make the students understand the procedure of the experiment.
• Experimental Work (80 minutes):
▪ Design of experiment: 10 minutes
▪ Data collection: 30 minutes
▪ Data analysis, drawing graphs and completing the result part: 40 minutes.
• Post Lab Discussion (15 minutes):
▪ The teacher will summarize the total lab work and have a discussion with the
students related to the questions given in the outcomes part.
• Report Submission:
▪ Students will prepare their lab report and submit it on the next class.
Page 1 of 5
Physics 1 Lab | Expt. # 6
6.5 Theory
Ohm's law states that at a constant temperature the current through a conductor between two points is
directly proportional to the voltage across those two points. Introducing the constant of proportionality,
the resistance, one arrives at the usual mathematical equation that describes this relationship:
𝑽 = 𝑰𝑹
where I is the current and V is the potential difference across the resistance R.
Rh V
Rx V
Slope = R
A
(a) (b) I
Figure 6.1: (a) Simple circuit to determine unknown resistance, Rx by using Ohm’s law, ammeter (A) and voltmeter (V) are
used to measure the current and potential drop in the circuit, variable resistor, R h is used to change the current flow in the circuit
(b) Slope of the V vs I graph gives the value of R.
When N number of resistors are connected in series and parallel connections their equivalent resistances
Rs and Rp are calculated by the following two equations:
𝑹𝒔 = 𝑹𝟏 + 𝑹𝟐 + ⋯ + 𝑹𝑵
𝟏 𝟏 𝟏 𝟏
= + + ⋯+
𝑹𝒑 𝑹𝟏 𝑹𝟐 𝑹𝑵
Rh
Rh
R1 R1 R2 V
V
R2
A A
(a) (b)
Figure 6.2: Series and parallel connections are shown for two resistors R1 and R2 in (a) and (b), respectively.
6.6 Apparatus
Power supply, variable resistor, ammeter, voltmeter, unknown resistors and connecting wires.
Page 2 of 5
6.7 Procedure
• Construct above circuits with 2 unknown resistances (R1 & R2).
• Using rheostat Rh choose current not more than 1 A. Vary Rh to select 10 different currents through
the circuit as measured by the ammeter A.
• Measure the corresponding potential differences (V) in the voltmeter.
6.8 Experimental Data

Table 6.1: Voltage current records for R1 and R2
Resistors Current Voltage

I V
(A) (V)
R1
R2
Page 3 of 5
Table 6.2: Voltage current records for series and parallel connections.
Combinations of Current Voltage

I V
R1 & R2 (A) (V)
Series Combination
Parallel Combination
6.9Analysis and Calculation

• Use EXCEL to plot V versus I graphs. You have to plot 4 graphs for R1, R2, R1 and R2 in series
and parallel connections.
• Find the best fitted lines. Determine the slope of the best fitted lines to get the values of R1, R2, Rs
and Rp.
• Also calculate the values of Rs and Rp by using the values of R1 and R2 according to the laws of
series and parallel combinations of resistors.
Page 4 of 5
6.10 Result
Table 6.3: Values of R1, R2, Rs and Rp.
Resistances from the graphs Comments

Calculated
Resistors Values in Ohms Values of Rs and
R1 Rp in Ohms
R2
Rs
Rp
6.11 Discussion
6.12 Resources
For further understanding students may go through the following resources:
• Fundamental of Physics (10th Edition): Ohm’s Law (Chapter 26, page 756-759)
• Video Links:
➢ https://www.youtube.com/watch?v=Vh3XGz7hgU4
➢ https://www.youtube.com/watch?v=hxYn74Yhkpk
➢ https://www.youtube.com/watch?v=2c1z4pLsI_w
Page 5 of 5

Phy1Lab Exp. 6

Uploaded by

Copyright:

Available Formats

Phy1Lab Exp. 6

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Phy1Lab Exp. 6

Uploaded by

Copyright:

Available Formats

Physics 1 Lab | Expt.

(a) Study of Ohm’s law using unknown resistances.

6.4 Timing and Lab Activities (Total 3 Hours)

6.8 Experimental Data

Resistors Current Voltage

Combinations of Current Voltage

6.9Analysis and Calculation

Resistances from the graphs Comments

You might also like