COURSE CODE: EE 1C UNITS: 3

COURSE DESCRIPTION: INSTRUMENTATION AND CONTROL NO. OF HRS: 3

LESSON 2: ELEMENTS AND COMPONENTS OF CONTROL LOOPS
I. ELEMENTS OF CONTROL LOOPS
 Primary element/sensor
 Transducer
 Converter
 Transmitter

PRIMARY ELEMENT
In all cases, some kind of instrument is measuring changes in the process and reporting a process variable
measurement. Some of the greatest ingenuity in the process control field is apparent in sensing devices.
Because sensing devices are the first element in the control loop to measure the process variable, they
are also called primary elements.

 Examples of primary elements include:

o Pressure sensing diaphragms, strain o Magnetic flow tubes
gauges, capacitance cells o Coriolis flow tubes
o Resistance temperature detectors (RTDs) o Radar emitters and receivers
o Thermocouples o Ultrasonic emitters and receivers
o Orifice plates o Annubar flow elements
o Pitot tubes o Vortex shedder
o Venturi tubes

Primary elements are devices that cause some change in their property with changes in process fluid
conditions that can then be measured. For example, when a conductive fluid passes through the magnetic
field in a magnetic flow tube, the fluid generates a voltage that is directly proportional to the velocity of
the process fluid. The primary element (magnetic flow tube) outputs a voltage that can be measured and
used to calculate the fluid’s flow rate. With an RTD, as the temperature of a process fluid surrounding the
RTD rises or falls, the electrical resistance of the RTD increases or decreases a proportional amount. The
resistance is measured, and from this measurement, temperature is determined.

TRANSDUCERS
A transducer is a device that translates a mechanical signal into an electrical signal.
 For example, inside a capacitance pressure device, a transducer converts changes in pressure into
a proportional change in capacitance.

CONVERTERS
A converter is a device that converts one type of signal into another type of signal.
 For example, a converter may convert current into voltage or an analog signal into a digital signal.
In process control, a converter used to convert a 4–20 mA current signal into a 3–15 psig
pneumatic signal (commonly used by valve actuators) is called a current-to-pressure converter.

TRANSMITTERS
A transmitter is a device that converts a reading from a sensor or transducer into a standard signal and
transmits that signal to a monitor or controller.
 Transmitter types include:
o Pressure transmitters
o Flow transmitters
o Temperature transmitters
o Level transmitters
o Analytic (O2 [oxygen], CO [carbon monoxide], and pH) transmitters

Prepared by: Engr.JRLdR Page 1 of 4

COURSE CODE: EE 1C UNITS: 3
COURSE DESCRIPTION: INSTRUMENTATION AND CONTROL NO. OF HRS: 3
LESSON 2: ELEMENTS AND COMPONENTS OF CONTROL LOOPS
SIGNALS
There are three kinds of signals that exist for the process industry to transmit the process variable
measurement from the instrument to a centralized control system.
 Pneumatic signal
 Analog signal
 Digital signal

Pneumatic Signals
Pneumatic signals are signals produced by changing the air pressure in a signal pipe in proportion to the
measured change in a process variable.
The common industry standard pneumatic signal range is 3–15 psig. The 3 corresponds to the lower range
value (LRV) and the 15 corresponds to the upper range value (URV).
Pneumatic signaling is still common. However, since the advent of electronic instruments in the 1960s,
the lower costs involved in running electrical signal wire through a plant as opposed to running pressurized
air tubes has made pneumatic signal technology less attractive.

Analog Signals
The most common standard electrical signal is the 4–20 mA current signal. With this signal, a transmitter
sends a small current through a set of wires.
The current signal is a kind of gauge in which 4 mA represents the lowest possible measurement, or zero,
and 20 mA represents the highest possible measurement.
 For example, imagine a process that must be maintained at 100 °C. An RTD temperature sensor
and transmitter are installed in the process vessel, and the transmitter is set to produce a 4 mA
signal when the process temperature is at 95 °C and a 20 mA signal when the process temperature
is at 105 °C.
The transmitter will transmit a 12 mA signal when the temperature is at the 100 °C set point. As
the sensor’s resistance property changes in response to changes in temperature, the transmitter
outputs a 4–20 mA signal that is proportionate to the temperature changes. This signal can be
converted to a temperature reading or an input to a control device, such as a burner fuel valve.
Other common standard electrical signals include the 1–5 V (volts) signal and the pulse output.

Digital Signals
Digital signals are the most recent addition to process control signal technology.
Digital signals are discrete levels or values that are combined in specific ways to represent process
variables and also carry other information, such as diagnostic information.
The methodology used to combine the digital signals is referred to as protocol.

Prepared by: Engr.JRLdR Page 2 of 4

COURSE CODE: EE 1C UNITS: 3
COURSE DESCRIPTION: INSTRUMENTATION AND CONTROL NO. OF HRS: 3
LESSON 2: ELEMENTS AND COMPONENTS OF CONTROL LOOPS
II. COMPONENTS OF CONTROL LOOPS
 Indicator
 Recorder
 Controller
 Correcting element/final control element
 Actuator

INDICATORS
While most instruments are connected to a control system, operators sometimes need to check a
measurement on the factory floor at the measurement point. An indicator makes this reading possible.
An indicator is a human-readable device that displays information about the process. Indicators may be
as simple as a pressure or temperature gauge or more complex, such as a digital read-out device.
Some indicators simply display the measured variable, while others have control buttons that enable
operators to change settings in the field.

RECORDERS
A recorder is a device that records the output of a measurement devices. Many process manufacturers
are required by law to provide a process history to regulatory agencies, and manufacturers use recorders
to help meet these regulatory requirements.
In addition, manufacturers often use recorders to gather data for trend analyses. By recording the
readings of critical measurement points and comparing those readings over time with the results of the
process, the process can be improved.

CONTROLLERS
A controller is a device that receives data from a measurement instrument, compares that data to a
programmed set point, and, if necessary, signals a control element to take corrective action.
Local controllers are usually one of the three types: pneumatic, electronic or programmable. Controllers
also commonly reside in a digital control system.
Controllers may perform complex mathematical functions to compare activities. A set of data to set point
or they may perform simple addition or subtraction functions to make comparisons.
Controllers always have an ability to receive input, to perform a mathematical function with the input,
and to produce an output signal. Common examples of controllers include PLC and DCS.

Programmable logic controllers (PLCs)—PLCs are usually computers connected to a set of input/output
(I/O) devices. The computers are programmed to respond to inputs by sending outputs to maintain all
processes at set point.
Distributed control systems (DCSs)—DCSs are controllers that, in addition to performing control functions,
provide readings of the status of the process, maintain databases and advanced man-machine-interface.
Types of process controllers

Prepared by: Engr.JRLdR Page 3 of 4

COURSE CODE: EE 1C UNITS: 3
COURSE DESCRIPTION: INSTRUMENTATION AND CONTROL NO. OF HRS: 3
LESSON 2: ELEMENTS AND COMPONENTS OF CONTROL LOOPS
CORRECTING ELEMENTS / FINAL CONTROL ELEMENTS
The correcting or final control element is the part of the control system that acts to physically change the
manipulated variable.
In most cases, the final control element is a valve used to restrict or cut off fluid flow, but pump motors,
louvers (typically used to regulate air flow), solenoids, and other devices can also be final control
elements. Final control elements are typically used to increase or decrease fluid flow.
 For example, a final control element may regulate the flow of fuel to a burner to control
temperature, the flow of a catalyst into a reactor to control a chemical reaction, or the flow of air
into a boiler to control boiler combustion. In any control loop, the speed with which a final control
element reacts to correct a variable that is out of set point is very important. Many of the
technological improvements in final control elements are related to improving their response
time.

ACTUATORS
An actuator is the part of a final control device that causes a physical change in the final control device
when signaled to do so.
The most common example of an actuator is a valve actuator, which opens or closes a valve in response
to control signals from a controller.
Actuators are often powered pneumatically, hydraulically, or electrically. Diaphragms, bellows, springs,
gears, hydraulic pilot valves, pistons, or electric motors are often parts of an actuator system.

Prepared by: Engr.JRLdR Page 4 of 4