Scribd
Upload
44 views

Assignment 1

This document contains 7 questions related to orthogonal cutting processes and calculations. It asks the reader to: 1) Calculate the mean shear strength and mean frictional stress using given cutting force and geometry values. 2) Derive an equation relating shear strength, specific cutting energy, chip thickness ratio, and friction coefficient. 3) Show that for a given cutting condition, the friction coefficient must be less than or equal to 4/3. 4) Calculate shear angle and forces given values for various cutting parameters of mild steel. 5) Calculate shear angle and strain for different rake angles using chip thickness values. 6) Estimate friction coefficient and predict new forces for a change in rake angle, using Merchant

Uploaded by

ayushagarwal.techfest
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
44 views

Assignment 1

This document contains 7 questions related to orthogonal cutting processes and calculations. It asks the reader to: 1) Calculate the mean shear strength and mean frictional stress using given cutting force and geometry values. 2) Derive an equation relating shear strength, specific cutting energy, chip thickness ratio, and friction coefficient. 3) Show that for a given cutting condition, the friction coefficient must be less than or equal to 4/3. 4) Calculate shear angle and forces given values for various cutting parameters of mild steel. 5) Calculate shear angle and strain for different rake angles using chip thickness values. 6) Estimate friction coefficient and predict new forces for a change in rake angle, using Merchant

Uploaded by

ayushagarwal.techfest
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ME 338

Manufacturing Process 2
Autumn 2023 – 24 (Batch S2)
Assignment 1

1. In an orthogonal cutting test, the following condition were noted:

Width of cut = 2.5 mm Working normal rake angle = 5°


Undeformed chip thickness = 0.25 mm cutting force Fc = 900 N
Chip thickness = 1.0 mm Thrust force Ft = 450 N
Chip Tool contact length lf = 0.75 mm

Calculate
a. The mean shear strength of the work material
b. The mean frictional stress on the tool face

2. Show that in metal cutting when the working normal rake is zero, the ratio of eth
shear strength of the work material, τs to the specific cutting energy ps is given by
𝜏𝑠 (1−𝜇𝑟𝑐 )𝑟𝑐
=
𝑝𝑠 1+ 𝑟𝑐 2

where µ is the co-efficient of chip- tool friction, and rc is the chip thickness ratio

3. For the orthogonal cutting of a particular work material, it is found that the length of
the chip tool contact is always equal to the chip thickness t and that the mean shear
stress at the chip tool interface is equal to the mean shear stress on the shear plane.
Show that, under the circumstances, the mean coefficient of friction on the tool face
µ must be equal to or less than 4/3 and that when it is equal to unity, the shear
angle, ϕ, is equal to the working normal rake 𝛾.

4. Mild steel is being machined at a cutting speed of 200 m/min with a tool of rake
angle 10◦. The width of cut and the uncut thickness are 2 mm and 0.2 mm,
respectively. If the average value of the coefficient of the friction between the tool
and the chip is 0.5 and the shear stress 𝜏𝑠 of the work material is 400 N/mm2 ,
determine

(i) the shear angle ,


(ii) the cutting and the thrust components of the machining force.

5. The chips from an orthogonal cutting operation with an uncut thickness of 0.2 mm
for various rake angles are:
𝛾 15◦ 10◦ 5◦ 0◦
tc 0.45 0.5 0.63 1.13
Calculate, for each chip, the corresponding shear angle and shear strain and plot
them against 𝛾.

6. The cutting and thrust components of the machining force during orthogonal
machining of aluminum with a rake angle of 10◦ are found to be 312 N and 185 N,
respectively,
i. Estimate the coefficient of friction between the tool and the chip
ii. If the rake angle is reduced to 0◦, keeping all the other parameters the same, and
if the coefficient of friction also remains unchanged, estimate the new values of Fc
and Ft , using Merchant’s first solution.

7. Calculate the mean shear plane temperature rise θs during orthogonal machining
with zero rake. Given
Uc = 1.5 J/mm3, µ= 0.8, t = 0.2 mm, rc = 0.2, ρ= 7000 kg/m3, c = 500 J/kg-◦C,
V = 2 m/sec. Assume that 15% of the heat generated goes into the workpiece.

*******

You might also like