Release Notes v5.0.3 and v5.00.03 - EcoStruxure Building Operation 2023 and SpaceLogic, EasyLogic Controller Firmware
Release Notes v5.0.3 and v5.00.03 - EcoStruxure Building Operation 2023 and SpaceLogic, EasyLogic Controller Firmware
03
Release Notes
This document is written for and on behalf of Schneider Electric and is supplied on the express terms that it is to be treated as
confidential and that it may not be copied, used, or disclosed to others except as authorized in writing by this Company. This document
is intended for internal use only.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 1 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
This EBO software release is fully compatible with SpaceLogic and EasyLogic Controller
firmware v5.00.03.
• This release supersedes the v5.0.1, and v5.0.2 releases and should be used for
all upgrades to 5.0 and new greenfield sites.
• There is a new build of the controller firmware to accompany this release
(v5.00.03).
• It is imperative that any upgrades be accomplished only after reading and
understanding this document and the v5.0.1, v5.0.2 release notes.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 2 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Table of contents
ABOUT THIS RELEASE ......................................................................................................................................................... 2
1. ECOSTRUXURE BUILDING OPERATION 2023 RELEASE V5.0.3 AND SPACELOGIC, EASYLOGIC CONTROLLER
FIRMWARE V5.00.03 AVAILABILITY..................................................................................................................................... 5
3. FIELD REPORTED DEFECTS FIXED IN ECOSTRUXURE BUILDING OPERATION V5.0.3 RELEASE ..................... 27
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 3 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
6.3 SpaceLogic Series (MP-C/V, IP-IO, and RP-C) Factory Firmware ..................................................... 35
A2. Upgrading EcoStruxure Building Operation (From previous major releases) ...................................... 38
A2.1 System Upgrade Overview........................................................................................................................................ 38
A2.1.1 Upgrade Enterprise Server and Enterprise Central................................................................................................. 38
A2.1.2 Upgrading Automation Servers .............................................................................................................................. 38
A2.1.3 Upgrading WorkStation and Client Tools Installation .............................................................................................. 39
Change History.................................................................................................................................................. 44
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 4 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
The EcoStruxure Building Operation Release 5.0.3 deliverable includes the following
software and firmware.
* This release is NOT supported on the original AS’s often referred to as AS classic (part
number - SXWAUTSVR10001).
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 5 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
BMS Software Support Policy establishes a clear expectation for product support timelines.
There are two main levels of software support, Full support when the software is in its
active phase and Limited support for a period of two years after the active phase. For more
information, refer to the software support policy document on EcoXpert Extranet.
Ending Version
Upgrade Path
3.2 4.0 5.0
1.8 Via 3.1 Via 3.1 Via 3.1
Out of Support
1.9 Direct Via 3.2 Via 4.0
Starting Version
Current
Full Support
Version
* Versions 1.9 and earlier are not supported and should be upgraded to a fully supported
version. For details on older versions, see earlier versions' release notes
** Multi-version support is supported from EBO 3.0 onwards however excluding v3.3L. See
section 6.1 in Release Notes v5.0.1 for more details.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 6 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
1
Due to a defect, this will show as 5.03.00002 in the Device Report
Important Note: The SpaceLogic or EasyLogic Controllers shipped from the factory may not
have the latest firmware installed. It is essential to verify that the controller has the latest
firmware build loaded for the EcoStruxure Building Operation version build being used
before programming the controller.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 7 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
EBO
v2.00.0x v3.01.0x v3.02.0x v3.03.01 v4.00.0x v5.00.0x
Versions
Not
v5.0.x Supported Supported Supported Supported Supported
Supported
*Versions not mentioned in the table above are out of full support. Refer to earlier versions'
release notes for the older versions' compatibility matrix
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 8 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Supported* means it will work with BACnet IP but there is no support for configurability to
BACnet MSTP Northbound.
In cases where the compatibility matrix states “Not Supported” for a given pairing, there
remains limited support to allow that unsupported pairing to discover, host, and down-rev
from factory-installed firmware to ensure a compatible pairing is achieved.
Down-Rev from a factory installed 4.0 or 5.0 firmware IP Controller to “earlier” versions
It is important to note that any Down-Rev should be undertaken after hosting and prior to
connecting any external equipment (beyond power and Ethernet connection) and prior to
downloading any application or undertaking any other configuration of the controller.
Warning: Down-Rev is NOT supported between versions once the application is loaded onto
the controller. On controllers loaded with a database, an Erase Database or Factory Reset
command should be issued (and allowed to complete) before a downrev of the controller is
attempted. Once the downrev is completed, the database can be downloaded from the
server, assuming that the server and controller versions are compatible.
1.5 Licensing
EcoStruxure Building Operation 2023 (EBO) v5.0.3 requires either EBO 2022 licenses or EBO
2023 licenses to run.
If your system is currently based on EBO 2022 licenses, there is no need to upgrade your
existing licenses to EBO 2023 in order to operate with EBO 2023 (5.0.3).
1.5.1 Offline / Online definition when activating licenses
When activating embedded licenses EBO users need to consider if Online or Offline
activation methods should be used. From EBO release 5.0.3 the definition of Off-line/On-line
has changed.
On-line = Automation Server (AS) has an internet connection or Device Administrator (PC
running Windows) has an internet connection.
OR Internet = On-Line
Internet
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 9 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
1. In Script Editor, right-click in the Code pane and select Protect. A password entry
dialog appears.
2. Enter and confirm a password of 4-25 characters. The password used to protect a
Script program is independent of your Workstation user account and the rules
associated with Workstation passwords do not apply.
The Protect operation encrypts the Script source code and saves the Script program, even
if the code contains errors. Once protected, the Script program’s code is displayed as
encrypted text and can no longer be legibly viewed or edited in Workstation or Script
Editor until you unprotect the program.
You can protect all types of Script programs, except for programs in i2 and b3 controllers.
Protecting a Script program does not prevent the script from running, being copied,
exported for reuse, or being deleted. When you paste or import a protected program, the
pasted or imported program remains protected with the same password as used to
originally protect it. In Workstation, you can modify the bindings associated with the
protected Script program.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 10 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
IMPORTANT: Script program code protection is not supported in EBO versions prior to
5.0.3. In multi-version systems, when logged onto ES or EC version 5.0.3 or later, do not
protect Script program code residing in servers running an earlier version. Doing so can
result in the loss of data if another user inadvertently saves a protected program while
logged on directly to the server running the earlier version.
You have now unprotected your Script program. The Script Editor displays the original
source code.
NOTE: After unprotecting a Script program in Script Editor, the program will remain
protected on the EBO server until you save the program in Script Editor. If you unprotect a
program in Script Editor and close the program without saving it, you will need to re-enter
the password to view the program contents the next time you open the program in Script
Editor.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 11 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Note: This functionality is supported in Script programs only in Enterprise Server and
Enterprise Central version 5.0.3 and later. This functionality is not supported in Script
Functions or Script Event Programs, nor in devices other than Enterprise Server or
Enterprise Central.
In script programs, you use a new Trendlog binding variable type to configure access to a
trend log and a new system function called Read to read records from the trend log as
follows.
Trendlog
• Trendlog assigns the name that follows it as a binding variable, which you bind to a
trend log object.
• Syntax: Trendlog namelist
o namelist is a list of one or more user-defined script binding variable names
separated by commas.
• You bind Trendlog binding variables to the trends you wish to access in the script
program. The trend logs you bind to must be in the same server as the Script
program.
Read
• Read is a Script program system function that reads trend records from a trend log
into a script program.
• Syntax: variablename.Read (start_time, end_time, requested_number, value_array,
timestamp_array, received_number)
o variablename is a script binding variable of type Trendlog.
o start_time, end_time are datetime values that specify the range of time within
the bound trend log to read trend records. Datetime values must be in server
local time.
o requested_number is a numeric value that specifies the maximum number of
records to read from the trend log.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 12 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
o Value_array is a numeric array that receives the Value from each trend record
read.
o timestamp_array is a datetime array that receives the Time stamp from each
trend record read.
o received_number is a numeric value that indicates the actual number of trend
records read.
• The sizes of value_array and timestamp_array are automatically adjusted to match
the number of trend points read from the trend log.
See WebHelp topic Script Program Access to Trend Logs for an example.
2.3.2 Script Data Files - Generic tables that can interact with script
A Script data file is an object that represents a two-dimensional table consisting of columns
and rows. Cells within the data file are defined by column and row indices. Each cell can
contain a string, numeric, or datetime value that can be written to and read by a Script
program using a set of new Script functions.
When you view a Script data file in WorkStation, you see a table that displays the contents
of the data file arranged in rows and columns with column headers that you can edit in
WorkStation
Note: This functionality is supported in Script programs only in Enterprise Server and
Enterprise Central version 5.0.3 and later. This functionality is not supported in Script
Functions or Script Event Programs, nor in devices other than Enterprise Server or
Enterprise Central.
Note: It's not possible to modify the contents of the data file in Data File tab. The contents
of the data file can only be modified by a Script program.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 13 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
When creating a Script data file, you enter the number of columns and rows in the object
creation wizard.
Warning: If you later need to adjust the number of rows or columns in the data file, you
can change the data file's Number of rows or Number of columns properties. However,
doing so causes the data in the file to be cleared. So, when creating a data file, be sure to
allow extra rows and columns to anticipate the maximum needs of your application.
In script programs you use a new Datafile binding variable type to configure access to
datafiles and several new system functions to interact with datafiles as follows.
Datafile
• Datafile is a new Script program keyword that assigns the name that follows it as a
binding variable, which you bind to a datafile object.
• Syntax: Datafile namelist
o namelist is a list of one or more user-defined script binding variable names
separated by commas.
• You bind Datafile binding variables to the datafiles you wish to access in the script
program. The datafiles you bind to must be in the same server as the Script
program.
Open
• Open prepares a Script program to access a datafile. You must open a data file
before performing any other operations on the data file.
• Syntax: variablename.Open()
o variablename is a script binding variable of type Datafile.
o Open is an asynchronous operation, so Open must be on its own labeled line in
the Script program.
Write
• Write writes data to a data file.
• Syntax: variablename.Write(row_number, column_number, source_value)
o variablename is a script binding variable of type Datafile.
o row_number and column_number are numeric values that specify the row and
column of the cell to be written.
o source_value is a numeric, string, or datetime value to be written to the cell.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 14 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Read
• Read reads a cell from a data file.
• Syntax: variablename.Read(row_number, column_number, return_value)
o variablename is a script binding variable of type Datafile.
o row_number and column_number are numeric values that specify the row and
column of the cell to be read.
o return_value is a numeric, string, or datetime value to receive the data from
the file.
• Read accesses the referenced data file, reads data from the cell specified by
row_number and column_number, and assigns the result to return_value. The data
type of return_value must match the type of data present in the specified cell.
Clear
• Clears the contents of a data file.
• Syntax: variablename.Clear()
o variablename is a script binding variable of type Datafile.
Save
• SAVE saves the contents of a datafile to the server's database.
• Syntax: variablename.Save()
o variablename is a script binding variable of type Datafile.
• Save is an asynchronous operation, so Save must be on its own labeled line in the
Script program.
• Save holds the program at its current line for 10 seconds to mitigate the risk of too
frequent save operations blocking access to the server database for other processes.
• Save updates the Size in Kbytes property of the datafile.
Close
• Close terminates access to the referenced datafile.
• Syntax: variablename.Close()
o variablename is a script binding variable of type Datafile.
• Close is an asynchronous operation, so Close must be on its own labeled line in the
Script program.
Rows
• Rows returns the number of rows in a datafile.
• Syntax: numericvalue = variablename.Rows()
o numericvalue is a variable of type numeric.
o variablename is a script binding variable of type Datafile.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 15 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Columns
• Columns returns the number of columns in a datafile.
• Syntax: numericvalue = variablename.Columns()
o numericvalue is a variable of type numeric.
o variablename is a script binding variable of type Datafile.
It is now possible to send historical data to AVEVA PI System. The historical data can only
be written to PI System (I.e. it cannot be read back). For more information about PI
Historian and how to set up the database, please go to AVEVA home page.
We have tested with Pi Web API 2021 SP3. We have not tested older versions, but
according to AVEVA, 2018 should work as well.
After setting up the PI System, go to Control Panel and choose PI Historian under External
Log Storage:
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 16 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Configure Host address, Asset server, Database name and credentials. Configure a Point
source to categorize the data for easier access and search. Compression is possible, but
only for new points. If the point already has written data in PI Historian, the data cannot be
compressed afterward. Either remove the tag and set a new one or enable compression
manually in PI System. Enumeration tables can also be written to PI System, i.e. units,
alarm states, etc.
Trend logs
By default, no trend logs are writing data to PI System. The trend log must be configured
with a tag name (PITagName=) in the Note 2 property to write data. Note 2 can still be
used for other purposes.
• @(Path) – Will add the log-object path to the tag-name. Initial / is removed.
• @(Name) – Will add the log-object-name to the tag-name.
• @(MonitoredPath) - Will use the source log path if source log use @(Path). Can be
used to merge Extended trend logs with source log.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 17 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Examples:
PITagName=@(Path)
PITagName=EBO_@(Name)
PITagName=@(MonitoredPath)
PITagName=MyTempLog1 or Building1_Floor2_Room3_TempSensor
Events
Event can have its own tag name. A few columns are default configured, so select columns
to the right and drag and drop them to the editor to get more. Column data will be stored
with delimiter |.
General behavior
• No trend logs are written by default, only after adding PITagName to the Note2 will
the log start transferring.
• You can change the tag-name and it will start writing to the new one right away, the
old one will not be deleted in PI.
• Deleting PITagName from Note2 will stop that log from transferring, nothing will be
deleted from PI.
• Moving/Renaming a log will not change the tag-names in PI until disable/enable has
been performed for trends. Applicable when using @(Path), @(Name) and
@(MonitoredPath) as tag name.
• If you want to change the tag-name/columns for events then you need to
disable/enable for events before it applies.
PI System Explorer
Data can be viewed in PI System Explorer. Choose the database:
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 18 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Example how to view data. Search for the tag name and drag item to the area. Right-click
and select Time Series Data:
Event data is presented in similar way, with | as delimiter between the columns:
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 19 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
When performing Online activation on multiple selected Automation Servers the process
has been improved. Previously the activation was made one server at a time. From EBO 5.0.3
the Device Administrator simultaneously works on activation of 20 Automation Servers. This
improves the overall activation fundamentally. A simultaneous license activation test made
on 20 various models of servers showed that the overall time to activate all 20 servers was
24 minutes. With the improvement in EBO 5.0.3, the time was reduced to 2 minutes. The
improvement was also made robust with 3 automatic retrials on Servers that fails to activate.
The retrials eliminate the effect of temporary bad connections or other not foreseen glitches
in the system.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 20 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
In EBO 5.0.3 the Device Administrator connectivity has improved. Now the existing
operational feature can use Device Administrator (DA) to communicate with the FNO (cloud
license server). Previously the below features needed an internet connected Automation
Server to communicate with FNO. From EBO 5.0.3 the below features can be used when only
DA is internet connected.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 21 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
During the discovery process, the Power Delivery relays will be switched off and on in
order to identify the terminals.
A new command “Discover Terminals only” has been introduced to discover on which terminal
each DALI light is connected to without impacting the current DALI address and association.
This command must be executed after upgrading an installation to 5.0.3 to allow to use of the
Energy Saving feature.
The Device Discovery UI has been updated to display the terminal information and group the Lights
based on that terminal information.
Note that if the terminal has not yet been discovered (for instance, after upgrading to 5.0.3) or
can’t be discovered (light with external power supply or terminal associated to a relay), the light
terminal will be displayed as “unknown terminal”.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 22 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
A DALI Channel Group allow to control all the lights connected to a terminal as one light, there is no
association to perform (simplified commissioning), the DALI Channel Group must be associated to
one of the 4 terminals (that terminal must not be already associated to another Group Channel or
to a Relay) and a group address must be set.
Note: The Group address shares the same address space as the regular DALI light group.
To control and configure the lights on that Group channel, the same properties as a DALI Light are
available and will be applied to each light on that terminal (if these lights were powered by the
module during discovery process).
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 23 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
The Device Discovery UI is updated once a Channel group is created to highlight that it is associated
to that terminal.
Note that the lights connected to that terminal cannot be associated to a DALI light/group if a
Channel Group is associated to that terminal (these lights can only be controlled using the Channel
Group), but they can be winked from the Device discovery view.
When the Terminal Relay is open (Energy saving is active), then it can take about 200ms to send a
command to a light (close relay, wait that lights power up, and send command).
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 24 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
A DALI Relay allow to control for instance a 230 VAC light on a terminal on which there is no DALI
light connected. The DALI Relay object is similar to the Relay object of the Relay 10 module. It must
be associated to one of the 4 terminals (that terminal must not be already associated to another
Relay or to a Group channel).
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 25 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Note that no DALI Light can be controlled if they are connected to the terminal associated to the
Relay.
If any lights is connected and discovered before creating the relay or if the relay was closed during
the discovery, then these lights will be listed in the Device Discovery page but cannot be controlled.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 26 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 27 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 28 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 29 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
The table below lists new known defects since 5.0.2 release. For the known issues list up
until EBO v5.0.2, refer to previous version’s release note here.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 30 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 31 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 32 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
The table below lists all known defects that affect the IP Controller firmware (MP-C, MP-V,
RP-C, or IP-IO controllers, CRS Modules, SpaceLogic sensors and Remote Control) since
5.00.02 release. For the known issues list up until EBO v5.00.02, refer to previous version’s
release note here.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 33 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
For more information refer to the Schneider Electric Recommended Cybersecurity Best
Practices document https://www.se.com/us/en/download/document/7EN52-0390/.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 34 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Important engineering information with regard to the SpaceLogic Controller (MP-C/V, IP-
IO, and RP-C) is also listed below.
Selecting the targeted folder or area in the system tree that you wish to evaluate, instead
of the root, can avoid longer load times.
Any new object created with this release will contain the new properties, this command is
only applicable when upgrading from an earlier release.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 35 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 36 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Device Discovery view updated with terminal information (and ready to support Power Saving):
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 37 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
APPENDIX A – Procedures
A1. Installing EcoStruxure Building Operation
For installation of EcoStruxure Building Operation v5.0.3 WorkStation, Enterprise Server,
Enterprise Central, please reference the Web Help for that topic.
Note2: If upgrading from v5.0.x to this release v5.0.3, please refer to section A3 below.
Warning: Upgrading from the pre-release (v5.0.1) bench tester build is not supported.
A system upgrade can include an Enterprise Server Enterprise Central, one or more
automation servers and Workstations, and the supporting administrator software, such as
Device Administrator. For more information, see System Upgrade Overview
If your EcoStruxure BMS contains an Enterprise Central, use the Enterprise Central Upgrade
Workflow.
Note1:
Depending upon the size of the system and the quantity of trends, it is possible that the
database on the Enterprise Server/ could be quite large. When upgrading, always make
certain that you have at least twice as much disk space available as the size of your database.
It should also be expected that the Enterprise Server may appear to “hang” for as much as
20 to 30 minutes upon the first initial start-up after the upgrade, but only on the first start.
To upgrade a single automation server or a series of standalone automation servers, use the
Automation Server System Upgrade Workflow.
You use Device Administrator to upgrade the automation server. You must upgrade Device
Administrator before you upgrade the automation server.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 38 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Note:
In case of issues compiling or saving applications in WorkPlace Tech Editor, update Visio with
the latest Microsoft Office updates.
A3 Upgrading EcoStruxure Building Operation v5.0.x.x to v5.0.3
Warning: Ensure a backup is available for all servers to be upgraded before proceeding.
A3.1 Automation Server
Applying Hotfix on an AS-P/AS-B is performed using the Device Administrator (DA).
The new v5.0.3 Device Administrator should be used by running the installer “Device
Administrator v5.0.3.117 - EcoStruxure Building – Software”
Warning: If the PC does not have access to the internet please refer to this topic in the
online help using another PC with internet access.
https://ecostruxure-building-help.se.com/bms/Topics/show.castle?id=13241&locale=en-
US&productversion=2023&a=1
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 39 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
If you use External Log Storage, new scripts must be run in the PostgreSQL/TimescaleDB
database for EBO 5.0. The script “pg_install_db.sql” can handle schema upgrades from 3.0
and forward.
For more info, read WebHelp Topic: “Setting up a Database Schema in the PostgreSQL
Database”.
A4.2 MSSQL database schema
Use the workflow described here to install and configure the EcoStruxure BMS External Log
Storage feature using Microsoft SQL Server.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 40 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Down-Rev from a factory installed 4.0 or 5.0 firmware IP Controller to “earlier” versions
It is important to note that any Down-Rev should be undertaken after hosting and prior to
connecting any external equipment ( beyond power and Ethernet connection) and prior to
downloading any application or undertaking any other configuration of the controller.
Warning for IP controllers: Down-Rev is NOT supported between versions once the
application is loaded onto the controller.
Using WorkStation, you can update the firmware of multiple BACnet/IP devices and their
attached SpaceLogic Sensor devices, RP controller expansion modules, and multi-sensors at
the same time with minimum downtime. In particular, the universal upgrade package
simplifies the update process and requires minimal user involvement and coordination. See
BACnet/IP Device Firmware Management for more information.
The upgrade is complete once the Firmware upgrade status returns to Normal, when it is
queued for upgrading the status shows ready and when downloading a percentage is
shown. Should the upgrade fail a warm start of the RP-C should be performed.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 41 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
WARNING: SpaceLogic and EasyLogic controllers update the SpaceLogic Sensor firmware in
the background after the upgrade process seems to be complete as viewed in the
Firmware Upgrade Viewer. It can take several minutes per SpaceLogic Sensor to transfer
files and restart them. During this time, SpaceLogic Sensor may appear offline and sensor
data will be unavailable.
Once the upgrade is complete, please refer to section 6.3 above regarding restoring
optional properties.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 42 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
NOTE: The BootApplet version is only upgraded if the current boot BootApplet doesn’t exceed the
minimum Boot Applet required to support the incoming firmware, consequently the BootApplet
version might not match to what is shown in the package metadata file.
To see all the versions in a package, select the following in the Firmware File Manager list and
navigate to Actions Tab and click on Open metadata file to view the Meta Data File:
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 43 of 44
Internal
Internal
[ Release Notes ] EcoStruxure™ Building Operation 2023 v5.0.3 and SpaceLogic, EasyLogic controllers v5.00.03
Change History
Revision Date Revision Description/Change
/Author
A 2023-06-20 R. Yanappa Approved.
Schneider Electric
Boston ONE Campus, 800 Federal Street, Andover, MA 01810 Telephone +1 978-794-0800 www.se.com
RN_EBO 2023_v5.0.3 Rev A – June 2023 Page 44 of 44
Internal
Internal