FMC230 Quick Manual v1.3
FMC230 Quick Manual v1.3
FMC230 Quick Manual v1.3
Warranty Disclaimer........................................................................ 18
Know your device .......................................................................... 3
Pinout ................................................................................................. 4
Wiring scheme................................................................................... 5
Characteristics............................................................................. 12
2 FMC230 | Wiki
Know your device
3 FMC230 | Wiki
Pinout
Table 1 FMC230 2x6 socket pinout
4 FMC230 | Wiki
Wiring scheme
1
1 1
1
Automotive relay
5 FMC230 | Wiki
Set up your device
How to insert Micro-SIM card and
connect the battery
1. You will receive your device partly closed.
Figure 4 Partly closed device Figure 5 Cover removal
2. Gently remove top and bottom covers.
3. Insert SIM card as shown with PIN request disabled or read
our Wiki how to enter it later in Teltonika Configurator. Make
sure that Micro-SIM card cut-off corner is pointing outward
from slot.
4. Connect battery as shown to device. Position the battery in
place where it does not obstruct other components.
5. After configuration, see “PC Connection (Windows)”, attach Figure 6 SIM card insert Figure 7 Battery connection
device top and bottom cover back and press them twice to the
full closure.
6. Make sure that product casing is closed correctly.
IMPORTANT! This device has an IP67 casing with a two-phase closing, that
ensures reliable protection and ease of use. Please make sure that product
casing corner clips are fixed tightly and cable is connected to the device in
order to maintain the degree of IP67 protection.
6 FMC230 | Wiki
PC Connection (Windows) Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
1. Power-up FMC230 with DC voltage (10 – 30 V) power supply
setup.
using supplied power cable. LED’s should start blinking, see
“LED indications”.
2. Connect device to computer using Micro-USB cable or Configuration (Windows)
Bluetooth connection:
• Using Micro-USB cable At first FMC230 device will have default factory settings set. These
▬ You will need to install USB drivers, see “How to install settings should be changed according to the user's needs. Main
USB drivers (Windows)” configuration can be performed via Teltonika Configurator
• Using Bluetooth software. Get the latest Configurator version from here.
▬ FMC230 Bluetooth is enabled by default. Turn on Configurator operates on Microsoft Windows OS and uses
Bluetooth on your PC, then select Add Bluetooth or prerequisite MS .NET Framework 5.0. Make sure you have the
other device > Bluetooth. Choose your device named – correct version installed.
“FMBxxx_last_7_imei_digits”, without LE in the end.
Table 2 MS .NET requirements
Enter default password 5555, press Connect and then
select Done. MS .NET REQUIREMENTS
3. You are now ready to use the device on your computer. Operating MS .NET Framework
Version Links
system version
7 FMC230 | Wiki
Various Status window tabs display information about GNSS,
GSM, I/O, Maintenance and etc. FMC230 has one user editable
profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
Figure 10 Language selection
functionality:
Configuration process begins by pressing on connected device
(Figure 11 Device connected via USB). 1. Load from device – loads configuration from device.
default.
8 FMC230 | Wiki
Quick SMS configuration Default configuration settings
Default configuration has optimal parameters present to ensure Movement and ignition detection:
best performance of track quality and data usage. Vehicle movement will Ignition will be detected
Quickly set up your device by sending this SMS command to it: be detected by by vehicle power voltage
accelerometer between 13,2 – 30 V
" setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"
Device makes a record On Moving if one of these events happen:
9 FMC230 | Wiki
Mounting recommendations
▬ When the module is connected, measure the voltage again
to make sure it did not decrease.
▬ It is recommended to connect to the main power cable in
with a standard cable the fuse box.
▬ 3 A, 125 V external fuse shall be used.
• Connecting wires
▬ Wires should be connected while the module is not plugged • Connecting ignition wire
in. ▬ Be sure to check if it is a real ignition wire i. e. power does
▬ Wires should be fastened to stable wires or other non- not disappear after starting the engine.
moving parts. Any heat emitting and/or moving objects ▬ Check if this is not an ACC wire (when key is in the first
should be kept away from the wires. position, most of the vehicle electronics are available).
▬ There should be no exposed wires. If factory isolation was ▬ Check if power is still available when you turn off any of
removed while connecting the wires, the isolation material vehicles devices.
should be applied. ▬ Ignition is connected to the ignition relay output. As
▬ If the wires are placed in the exterior or in places where they alternative, any other relay, which has power output when
can be damaged or exposed to heat, humidity, dirt, etc., ignition is on, may be chosen.
additional isolation should be applied and the wires should
not be loose. • Connecting ground wire
▬ Wires cannot be connected to the board computers or ▬ Ground wire is connected to the vehicle frame or metal
control units. parts that are fixed to the frame.
▬ If the wire is fixed with the bolt, the loop must be connected
• Connecting power source to the end of the wire.
▬ Be sure that after the car computer goes to sleep mode, ▬ For better contact scrub paint from the spot where loop is
power might be still available on the power wires. going to be connected.
Depending on the car model, this may happen in 5 to 30
minutes period.
10 FMC230 | Wiki
Mounting recommendations
with U-type cable
• Device fastening
▬ Locate the battery in your vehicle. If present remove the
battery cover to access the battery.
11 FMC230 | Wiki
LED indications Characteristics
Basic characteristics
Table 3 Navigation LED indications Table 5 Basic characteristics
Permanently switched on GNSS signal is not received FMC230- MBIB0: MeiG SLM320-E with Teltonika
TM2500
Blinking every second Normal mode, GNSS is working Name
FMC230- MCIB0: MeiG SLM320-LA with Teltonika
GNSS is turned off because: TM2500
Off Device is not working or Device is in
Technology LTE(CaT1)/2G(GSM/GPRS)/GNSS/BLUETOOTH
sleep mode
GNSS
Blinking fast constantly Device firmware is being flashed
GNSS GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS
Table 4 Status LED indications Receiver Tracking: 33
Blinking every second Normal mode Position Accuracy < 2.5 CEP
Blinking every two seconds Sleep mode Velocity Accuracy < 0.1 m/s (within +/- 15% error)
Blinking fast for a short time Modem activity Hot start <1s
CELLULAR
Technology LTE Cat 1, GSM
FMC230-MBIB0: GSM: B2/B3/B5/B8
2G bands
FMC230-MCIB0: GSM: B2/B3/B5/B8
12 FMC230 | Wiki
FMC230-MBIB0: LTE FDD: B1/B3/B7/B8/B20/B28 PHYSICAL SPECIFICATION
LTE-TDD:B38/B40/B41
4G bands 70,5 x 67,0 x 25,6 mm (L x W x H)
FMC230-MCIB0: LTE FDD:
B1/B2/B3/B4/B5/B7/B8/B20/B28 LTE-TDD:B40 Dimensions 85,0 x 67,0 x 25,6 mm (L x W x H) (length with
connector socket)
LTE: LTE FDD: Max 10Mbps (DL)/Max 5Mbps (UL)
LTE TDD: Max 8.96Mbps (DL)/Max 3.1Mbps (UL) INTERFACE
UMTS: WCDMA: Max 384Kbps(DL)/Max Digital Inputs 3
Data transfer
384Kbps(UL)
Negative Inputs 1 (Digital Input 2)
GSM: GPRS: Max 107Kbps (DL)/Max 85.6Kbps
(UL) Impulse Inputs 2 (Digital Input 1, Digital Input 2)
Data support SMS (text/data) Digital Outputs 3
Analog Inputs 2
Internal Back-up battery 170 mAh Li-Ion battery 3.7 V (0.63 Wh) GNSS antenna Internal High Gain
13 FMC230 | Wiki
Storage temperature Digital Input 1, Accelerometer, External Power
-20 °C to +45 °C
(with battery) Ignition detection Voltage, Engine RPM (CAN Adapters, OBDII
dongle)
Operating humidity 5% to 95% non-condensing
Battery discharge
-20 °C to +60 °C
temperature
FEATURES
Sensors Accelerometer
Green Driving, Over Speeding detection, GNSS
Fuel Counter, DOUT Control Via Call, Excessive
Idling detection, Immobilizer, iButton Read
Scenarios
Notification, Unplug detection, Towing
detection, Crash detection, Auto Geofence,
Manual Geofence, Trip, Ground Sense
GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra
Sleep modes
Deep Sleep
FOTA Web, FOTA, Teltonika Configurator (USB,
Configuration and firmware
Bluetooth), FMBT mobile application
update
(Configuration)
14 FMC230 | Wiki
Electrical characteristics ANALOG INPUT
Input voltage (Recommended Operating
0 +10 V
Table 6 Electrical characteristics Conditions), Range 1
Input resistance, Range 1 38.45 kΩ
VALUE
Measurement error on 12V, Range 1 0.9 %
CHARACTERISTIC DESCRIPTION
MIN. TYP. MAX. UNIT Additional error on 12 V, Range 1 108 mV
Drain current (Digital Output OFF) 120 µA Measurement error on 12 V, Range 2 0.9 %
Additional error on 12 V, Range 2 108 mV
Drain current (Digital Output ON,
0.1 0.5 A Measurement error on 30 V, Range 2 0.33 %
Recommended Operating Conditions)
Additional error on 30 V, Range 2 88 mV
Static Drain-Source resistance (Digital Output
400 600 mΩ
ON) OUTPUT SUPPLY VOLTAGE 1-WIRE
DIGITAL INPUT Supply voltage +4.5 +4.7 V
Output inner resistance 7 Ω
Input resistance (DIN1) 47 kΩ
Output current (Uout > 3.0 V) 30 mA
Input resistance (DIN2) 38.45 kΩ
Short circuit current (Uout = 0) 75 mA
Input resistance (DIN3) 150 kΩ
NEGATIVE INPUT
Input voltage (Recommended Operating Supply
0 V Input resistance 38.45 kΩ
Conditions) voltage
Input voltage (Recommended Operating Supply
Input Voltage threshold (DIN1) 7.5 V 0 V
Conditions) voltage
Input Voltage threshold (DIN2) 2.5 V Input voltage threshold 0.5 V
15 FMC230 | Wiki
Safety information All wireless data transferring devices produce
interference that may affect other devices which are
This message contains information on how to operate FMC230 safely. By placed nearby.
following these requirements and recommendations, you will avoid
The device must be connected only by qualified
dangerous situations. You must read these instructions carefully and
follow them strictly before operating the device! personnel.
• The device uses SELV limited power source. The nominal voltage is The device must be firmly fastened in a predefined
+12 V DC. The allowed voltage range is +10..+30 V DC. location.
• To avoid mechanical damage, it is advised to transport the device in
an impact-proof package. Before usage, the device should be placed
The programming must be performed using a PC with
so that its LED indicators are visible. They show the status of device
autonomic power supply.
operation.
• When connecting the 2x6 connector wires to the vehicle, the Installation and/or handling during a lightning storm
appropriate jumpers of the vehicle power supply should be is prohibited.
disconnected.
• Before unmounting the device from the vehicle, the 2x6 connector
The device is susceptible to water and humidity.
must be disconnected. The device is designed to be mounted in a
zone of limited access, which is inaccessible to the operator. All
related devices must meet the requirements of EN 62368-1 standard. CAUTION: Risk of explosion if battery is replaced by an
The device FMC230 is not designed as a navigational device for boats. incorrect type. Dispose of used batteries according to
the instructions.
16 FMC230 | Wiki
Certification and Approvals
17 FMC230 | Wiki
Warranty Warranty Disclaimer
TELTONIKA guarantees its products to be free of any TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
manufacturing defects for a period of 24 months. With additional WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS
agreement we can agree on a different warranty period, for more THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL
detailed information please contact our sales manager. IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY
EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY
Contact us teltonika.lt/company/contacts ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE,
All batteries carry a reduced 6 month warranty period.
LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC
If a product should fail within this specific warranty time, the LOSS.
product can be:
More information can be found at teltonika.lt/warranty-repair
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same
functionality
• TELTONIKA can also repair products that are out of warranty at
an agreed cost.
18 FMC230 | Wiki