Scribd Logo
Upload

Welcome to Scribd!

  • 16 views

    In07 05

    Uploaded by

    medjebeurmoustafa
    The document provides installation instructions for an ACM-302 air cylinder kit. It involves 8 steps: [1] removing existing parts from the valve spool; [2] placing an O-ring in the valve spool groove and greasing it; [3] sliding a spring retainer with an O-ring over the spool; [4] sliding on the piston assembly; [5] inserting a clevis pin through the assembly; [6] adding a piston cap; [7] finger tightening cap screws and testing operation; [8] fully torquing the cap screws. The kit includes 12 numbered parts to replace or install.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    In07 05

    Uploaded by

    medjebeurmoustafa
    16 views2 pages
    The document provides installation instructions for an ACM-302 air cylinder kit. It involves 8 steps: [1] removing existing parts from the valve spool; [2] placing an O-ring in the valve spool groove and greasing it; [3] sliding a spring retainer with an O-ring over the spool; [4] sliding on the piston assembly; [5] inserting a clevis pin through the assembly; [6] adding a piston cap; [7] finger tightening cap screws and testing operation; [8] fully torquing the cap screws. The kit includes 12 numbered parts to replace or install.

    Original Title

    IN07-05

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides installation instructions for an ACM-302 air cylinder kit. It involves 8 steps: [1] removing existing parts from the valve spool; [2] placing an O-ring in the valve spool groove and greasing it; [3] sliding a spring retainer with an O-ring over the spool; [4] sliding on the piston assembly; [5] inserting a clevis pin through the assembly; [6] adding a piston cap; [7] finger tightening cap screws and testing operation; [8] fully torquing the cap screws. The kit includes 12 numbered parts to replace or install.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    16 views2 pages

    In07 05

    Uploaded by

    medjebeurmoustafa
    The document provides installation instructions for an ACM-302 air cylinder kit. It involves 8 steps: [1] removing existing parts from the valve spool; [2] placing an O-ring in the valve spool groove and greasing it; [3] sliding a spring retainer with an O-ring over the spool; [4] sliding on the piston assembly; [5] inserting a clevis pin through the assembly; [6] adding a piston cap; [7] finger tightening cap screws and testing operation; [8] fully torquing the cap screws. The kit includes 12 numbered parts to replace or install.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ACM-302

    Installation Instructions

    1 2 3 4
    Remove detent ball Place the small O-ring in Slide spring retainer with Slide piston assembly
    retaining screw, spring, the wide “V” groove on the large O-ring placed around onto valve spool as
    ball, spool snap ring, and valve spool and grease.* the outside onto the valve shown below.
    washer. Remove spool spool. Flat side toward Grease* quadring seal.
    cover and ensure the O-ring valve housing.
    remained in valve housing.
    O-ring in valve housing Quadring seal

    5 6 7
    Slide clevis pin through Slide piston cap over piston Install cap screws finger tight. * Light duty petroleum or
    piston assembly and valve assembly. Make sure that Test with shop air for good spool synthetic grease.
    spool eye. Secure with the cap is centered and movement and to allow cap to
    provided snap ring. that the large O-ring (step center. Torque cap screws to
    3) is properly seated. 15 ft.lbs. alternating diagonal
    corners. Re-apply shop air to
    ensure proper operation. Raise port Lower port
    1 1
    ⁄8 in. NPT ⁄8 in. NPT
    ACM-302
    Installation Instructions

    AIR CYLINDER KIT: ACM-302 (Fits both E/EH Series) Ports are 1⁄8 in. NPT

    ITEM DESCRIPTION................. QTY........MUNCIE NUMBER Lower Port RaisePort


    1. Piston
    ⅛" NPT ⅛" NPT
    2. Quad Seal
    (PE1-1401-AV) Ass’y
    PE1-1400-AV
    3. Spring Retainer Only
    4. Spring
    5. Wire Ring
    6. Spring Retainer.......... 1.........PE1-1402-AV
    7. Small O-Ring............. 1.........PE1-1403-AV
    8. Clevis Pin................... 1.........PE1-1404-AV
    9. Snap Ring.................. 1.........PE1-1405-AV
    10. Large O-Ring............. 1.........PE1-1406-AV
    11. Pressure Cap............. 1.........PE1-1407-AV
    12. Cap Screw................. 4.........PE1-1408-AV

    201 East Jackson Street, Muncie, Indiana 47305


    800-367-7867 • Fax: 765-284-6991 • [email protected]
    Specifications are subject to change without notice. Visit www.munciepower.com
    A Member of the Interpump Group for warranties and literature. All rights reserved. © Muncie Power Products, Inc. (2011)

    IN07-05 (Rev. 04-17)

    You might also like