7SR11 and 7SR12 Argus Catalogue Sheet

Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

Reyrolle

Protection
Devices

7SR11 and 7SR12 Argus


Overcurrent Relays

Energy Management
7SR11 and 7SR12 Argus
Overcurrent Relays
Supervision
60CTS CT Supervision
74T/CCS Trip & Close Circuit Supervision
60VTS VT Supervision

Control
79 Auto Reclose
86 Lockout
CB Control

Features
Cold Load Settings
Four Settings Groups
Password Protection – 2 levels
User Programmable Logic
Self Monitoring
Description Circuit Breaker Trip and Maintenance Counter
Trip Timers
The 7SR11 & 7SR12 are overcurrent protection relays
developed to enhance the Argus family of products by
providing a familiar product using the latest generation of
User Interface
hardware technology.
The 7SR11provides overcurrent and earth fault protection, 20 Character x 4 Line Backlit LCD
the 7SR12 comes with additional voltage inputs providing Menu Navigation Keys
directional protection. Both relays are available in single and 9 User Programmable Tri-colour LEDs
four pole variants. User Language Configuration
Housed in a 4U high, size E4 or E6 (Optional IEC61850 mod-
el) cases, these relays provide protection, monitoring, in-
strumentation and metering with integrated input and out- Monitoring Functions
put logic, data logging & fault reports. Communication ac-
cess to the relay functionality is via a front USB port for local
PC connection, a rear electrical RS485 port for remote con- Primary/Secondary Current Phases and Earth
Direction
nection & optional IEC61850 communication through two
Primary/Secondary Line and Phase Voltages
rear Ethernet ports (Electrical or Optical).
Apparent Power and Power Factor
Real and Reactive Power
Function Overview W Hr & VAr Hr Forward and Reverse
Historical Demand Record
Positive Phase Sequence (PPS) Voltage & Current
Protection Negative Phase Sequence (NPS) Voltage & Current
37 Undercurrent Zero Phase Sequence (ZPS) Voltage
46BC Broken Conductor / Load Unbalance Frequency
46NPS Negative Phase Sequence Overcurrent Direction
49 Thermal Overload Binary Input/Output status
50 Instantaneous Overcurrent Trip circuit healthy/failure
50G/N/SEF Instantaneous Earth Fault Time and date
50AFD Arc Flash Detection (6 zones) Starters
50BF Circuit Breaker Fail Fault records
51 Time Delayed Overcurrent Event records
51G/N/SEF Time Delayed Measured/Derived/Sensitive EF Energy
64H High Impedance REF Circuit breaker trip counters
27/59 Under/Over Voltage I2t summation for contact wear
47 Negative Phase Sequence Voltage
51V Voltage Controlled Overcurrent
59N Neutral Voltage Displacement Hardware
67/50 Directional Instantaneous Overcurrent
67/50G/N Directional Instantaneous Earth Fault 1 CT 3 Binary Inputs 5 Binary Outputs
67/51 Directional Time Delayed Overcurrent 4 CT 3 Binary Inputs 5 Binary Outputs
67/51G/N Directional Time Delayed Earth Fault 4 CT 6 Binary Inputs 8 Binary Outputs
32 Directional Power 4 CT 4 Bin.In. 8 Bin.Out. (segregated rear terminals)
32S Directional Sensitive Power 1 CT 3 VT 3 Binary Inputs 5 Binary Outputs
55 Power Factor 4 CT 3 VT 3 Binary Inputs 5 Binary Outputs
81HBL2 Inrush Detector 4 CT 3 VT 6 Binary Inputs 8 Binary Outputs
81 Under/Over Frequency 4 CT 3 VT 4 Bin. In. 8 Bin.Out. (segregated rear terminals)
Line Check/Switch onto Fault

2 Siemens Protection Devices Limited


Data Storage and Function Matrix
Communication

FUNCTIONAL REQUIREMENT
Standard Communication Ports

7SR1102-1*A**-*[C/D]A0
7SR1102-1*A12-*AA0
7SR1101-1*A**-**A0

7SR1101-3*A**-**A0

7SR1102-3*A**-**A0

7SR1204-2*A**-**A0

7SR1204-4*A**-**A0

7SR1205-2*A**-**A0

7SR1205-4*A**-**A0
Front USB port + Rear RS485 port

Additional Optional Communication Ports

FUNCTION
2x Electrical RJ45 Ethernet ports
2x LC Fibre Optic Ethernet ports

27 Undervoltage ■ ■ ■ ■
Standard Protocols
32 Directional Power ■ ■
IEC60870-5-103, DNP3.0 or Modbus RTU 32S Directional Sensitive Power ■
User Selectable with programmable data points 37 Undercurrent ■ ■ ■ ■ ■ ■ ■ ■
46BC Broken Conductor / Load Unbalance ■ ■ ■ ■ ■
Optional Protocols Negative Phase Sequence
46NPS ■ ■ ■ ■
IEC61850 (E6 Case) Overcurrent
47 Negative Phase Sequence Voltage ■ ■

Ethernet Redundancy Protocols: 49 Thermal Overload ■ ■ ■ ■

Standard in all IEC61850 models: 50 Instantaneous Overcurrent ■ ■ ■ ■ ■

PRP (Parallel Redundancy Protocol) 50G Measured Instantaneous Earth Fault ■ ■ ■ ■ ■


RSTP (Rapid Spanning Tree Protocol) 50SEF
Measured Instantaneous Sensitive
■ ■ ■ ■
Earth Fault
HSR (High-availability Seamless Redundancy)
50N Derived Instantaneous Earth Fault ■ ■ ■ ■ ■

Data 50AFD Arc Flash Detection ■ ■ ■ ■


50BF CB Failure ■ ■ ■ ■ ■
Event Records – User Configurable
51 Time Delayed Overcurrent ■ ■ ■ ■ ■
Fault Records
Waveform Records 51G Measured Time Delayed Earth Fault ■ ■ ■ ■ ■

Measurands 51SEF
Measured Time Delayed Sensitive
■ ■ ■ ■
Earth Fault
Commands 51N Derived Time Delayed Earth Fault ■ ■ ■ ■ ■
Time Synchronism 55 Power Factor ■ ■
59 Overvoltage
Viewing and Changing Settings ■ ■ ■ ■
59N Neutral Voltage Displacement ■ ■ ■ ■
High Impedance Restricted Earth
64H ■ ■ ■ ■ ■ ■ ■ ■ ■
Application 67
Fault
Directional Overcurrent ■ ■
67G Directional Measured Earth Fault ■ ■
67SEF Directional Sensitive Earth Fault ■ ■
The Argus is a numerical overcurrent protection relay 67N Directional Derived Earth Fault ■ ■
intended for use on distribution and industrial networks. It 81HBL Inrush Detector ■ ■ ■ ■ ■ ■
provides a highly comprehensive functional software 81 Under/Over Frequency ■ ■ ■ ■
package with a range of integral application functions aimed CONTROL / MONITOR
at reducing installation, wiring and engineering time. 51c Cold Load - Phase Only ■ ■ ■ ■
An extensive range of metered values can be viewed on the 60CTS CT Supervision ■ ■ ■ ■ ■
front LCD or at a remote point via the communication 60VTS VT Supervision ■ ■ ■ ■
channel. 74T/CC
Trip & Close Circuit Supervision ■ ■ ■ ■ ■ ■ ■ ■ ■
S
The integrated control feature allows operation of a single
79 Autoreclose □ □ □ □
circuit breaker and monitoring of its trip and close circuits
86 Lockout ■ ■ ■ ■ ■ ■ ■ ■ ■
(except 7SR1102-1*A12-*AA0 models).
Line Check/SOTF ■ ■ ■ ■ ■ ■ ■ ■

Key - ■ - Included as standard


□ - Ordering option

Siemens Protection Devices Limited 3


7SR11 Functional Diagrams 7SR12 Functional Diagrams

Fig 1. Single Pole Overcurrent Relay

Fig 4. Single Pole Directional Relay

Fig 2. Four Pole Overcurrent Relay Version A software

Fig 5. Four Pole Directional Overcurrent Relay

Notes
1. Items shown dotted are only available in some
models; please refer to the Ordering Information
Section.
2. The use of some functions are mutually exclusive

Fig 3 Four Pole Overcurrent Relay Version C Software

4 Siemens Protection Devices Limited


impose a higher than normal load-current demand on the
Description of Functionality system which could exceed normal settings. These
conditions can exist for an extended period and must not be
interpreted as a fault. To allow optimum setting levels to be
27/59 Under/Over Voltage applied for normal operation, the cold load pickup feature
Each element has settings for pickup level, drop-off level and will apply alternative current settings for a limited period.
Definite Time Lag (DTL) delays. Operates if voltage exceeds The feature resets when either the circuit breaker has been
setting for duration of delay. closed for a settable period, or if the current has reduced
beneath a set level for a user set period.
32 Power
Each element has settings for pickup level, Definite Time Lag 50/51 Phase Fault
(DTL) delay and Direction. Each element can be set as Under 50 INST/DTL and 51 IDMTL/DTL elements provide overcurrent
or Over power, to operate from Apparent , Real or Reactive protection, each with independent settings for pickup
power and can be set for any phase or all three phases. current, time-multiplier (51) and time-delays. User can select
IEC or ANSI time current characteristics. The IDMT stage has
32S Sensitive Power a user programmable reset characteristic, either DTL or
This is provided in 4 pole SEF relays and provides elements shaped current ~ time reset characteristic, to improve
operated by single phase measured current in the ISEF input. grading with electromechanical protection.
Each element has settings for pickup level, Definite Time Lag
(DTL) delay and Direction. Each element can be set as Under 50G/51G/50N/51N Earth Fault/Sensitive Earth Fault
or Over power, to operate from Apparent, Real or Reactive Two earth fault measurement modes are available. One
power. mode directly measures the earth current from an
independent CT, or the residual connection of the 3 line CTs.
37 Undercurrent This input can be ordered as either earth fault or sensitive
Each element has settings for pickup level and Definite Time earth fault (50G/51G).
Lag (DTL) delays. Operates if current falls below setting for The second mode derives the earth current internally from
duration of delay. the 3 phase CT inputs to give earth fault (50N/51N). 50
INST/DTL and 51 IDMTL/DTL elements provide overcurrent
46BC Phase Unbalance/Broken Conductor protection, each with independent settings for pickup
Element has settings for pickup level and DTL delay. With the current, time-multiplier (51) and time-delays. User can select
circuit breaker closed, if the NPS:PPS current ratio is above IEC or ANSI time current characteristics. The IDMT stage has
setting this could be due to a broken conductor. a user programmable reset characteristic either DTL or
shaped current ~ time reset characteristic to improve grading
46NPS Negative Phase Sequence Overcurrent with electromechanical protection.
Each element has user settings for pickup level and IDMTL or The directional SEF element is also suitable for use on
DTL delay, operates if NPS current exceeds setting and delay. compensated networks.
NPS current elements can be used to detect unbalances on
1000
the system or remote earth faults when a delta-star
transformer is in circuit.

47 Negative Phase Sequence Voltage


Each element has settings for pickup level and Definite Time
Lag (DTL) delays. Operates if NPS voltage exceeds setting for
duration of delay. 100

49 Thermal Overload
The thermal algorithm calculates the thermal states from the Time
(sec)
measured currents and can be applied to lines, cables and
transformers. Alarm outputs are given for thermal overload
and thermal capacity. 10
Long Time Inverse

50BF Circuit Breaker Fail


The circuit breaker fail function may be triggered from an
internal trip signal or from a binary input. Line currents and Normal Inverse

earth currents are monitored following a trip signal and an


output is issued if any current is still detected, above setting,
after a specified time interval. Alternatively, if the trip is 1
Very Inverse

from a mechanical protection the circuit breaker position can


be used to determine a failure. A second time delay is
available to enable another stage to be utilized if required.
An input is also available to bypass the time delays when the Extremely Inverse

circuit breaker is known to be faulty.


0.1
51c Cold Load Pickup 1 2 3 4 5 6 8
10 20 30 40 50 60 80
100
Current (multiples of setting)
If a circuit breaker is closed onto a ‘cold’ load, i.e. one that
has not been powered for a prolonged period, this can Fig 6. IEC Overcurrent Curves

Siemens Protection Devices Limited 5


or two inputs fall below the setting. The 7SR12 has the
1000 above method and an addition method that considers the
presence of negative phase sequence current, without an
equivalent level of negative phase sequence voltage, for a
user set time as a CT failure.
Both element types have user operate and delay settings.

60VTS VT Supervision
100
The VT supervision uses a combination of negative phase
sequence voltage and negative phase sequence current to
detect a VT fuse failure. This condition may be alarmed or
Time used to inhibit voltage dependent functions. Element has
(sec)
user operate and delay settings.

10 64H Restricted Earth Fault


The measured earth fault input may be used in a 64H high
impedance restricted earth fault scheme to provide sensitive
high speed unit protection. A calculation is required to
determine the values of the external series stabilising
resistor and non-linear shunt resistor which can be ordered
1
Moderately Inverse separately.
Very Inverse
67/67N Directional Control
Phase, earth and sensitive earth fault elements can be
Extremely Inverse
directionalised. Each element can be user set to Forward,
Reverse, or Non-directional.
Directional Phase Fault elements are polarised from
0.1
2 3 4 5 6 8 20 30 40 50 60 80
quadrature voltage.
1 10 100
Current (multiples of setting) Derived earth fault elements can be user set to be polarised
from residual voltage or negative phase sequence voltage.
Fig 7. ANSI Overcurrent Curves
Measured earth fault elements are polarized from Vo.
51V Voltage Controlled Overcurrent
74T/CCS Trip & Close Circuit Supervision
Each phase shaped overcurrent element can be
The trip or close circuit(s) can be monitored via binary
independently controlled by the level of measured input
inputs. Trip circuit failure raises an HMI alarm and output(s).
voltage. For applied voltages above setting the 51-n
element operates in accordance with its current setting but
81HBL2 Inrush Restraint
for voltages below the setting a multiplier is applied to
reduce the 51-n pick up current setting. Where second harmonic current is detected (i.e. during
transformer energisation) user selectable elements can be
50AFD Arc Flash Detector blocked and an alarm given.
The 7SR1 relays can be used with the 7XG31 ReyArc range of
81 Under/Overfrequency
Arc Flash Detection devices. Arc fault protection is a tech-
nique employed for the fast clearance of arcing faults on Each element has settings for pickup level, drop-off level and
busbars, within metal clad switchgear & associated cable Definite Time Lag (DTL) delays. Operates if frequency ex-
boxes. The arc is detected using an optical sensor & the sig- ceeds setting for duration of delay. Typically applied in load
nal input to a protection device which also monitors the load shedding schemes.
current on the system. A trip signal can be achieved in less
than 10 ms using arc detection only or within 20 ms when Standard Version – Plus 79 Auto-Reclose
using overcurrent check. A high proportion of faults on an overhead line network are
transient and can be cleared quickly by high speed tripping
55 Power Factor followed by an automated circuit breaker reclose sequence.
Each element has settings for Under or Over Power Factor
pickup level, Definite Time Lag (DTL) delay and Lead/Lag The function provides independent phase fault and earth
Direction. Each can also be set for any phase or all three fault / sensitive earth fault sequences of up to 5 trip i.e. 4
phases operation. reclose attempts before lockout. An auto-reclose sequence
can be user set to be initiated from internal protection
59N Neutral Overvoltage operation or via binary input from an external protection.
Neutral overvoltage can be used to detect earth faults in
Programmable Logic
high impedance earthed or isolated systems.
Operates if the neutral voltage exceeds setting for duration The user can map binary inputs, protection elements, LEDs
of delay. and binary outputs together in a logical scheme.
Up to 4 logic equations can be defined using standard logic
60CTS CT Supervision functions e.g. Timers, AND/OR gates, Inverters and Counters
to provide the user required functionality.
The relay has two methods of CT supervision.. The 7SR11
Each logic equation output can be used for alarm &
monitors each phase current input and operates if any one
indication and/or tripping.
6 Siemens Protection Devices Limited
Virtual Inputs/Outputs Waveform recorder
There are 8 virtual inputs/outputs to provide internal logical The waveform recorder stores analogue data for all poles
states to assist in the application of the functions. Each and the states of protection functions, binary inputs, LEDs
virtual I/O can be assigned in the same way as a physical I/O. and binary outputs with user settable pre & post trigger
data. A record can be triggered from protection function,
Circuit Breaker Maintenance binary input or via data communications. 10 records of 1
Two circuit breaker operations counters are provided to second duration are stored. (5 records for 7SR1102-1*A12-
assist with maintenance scheduling. The maintenance *AA0 versions).
counter records the overall number of operations and the
delta counter records the number of operations since the Demand Metering
last reset. A record of demand is available. The demand minimum,
An I2t summation counter provides a measure of the contact maximum and average values for currents, frequency and if
wear indicating the total energy interrupted by the circuit applicable, voltages and real, reactive and apparent power,
breaker contacts. over a user selectable period of time, is displayed and
Each counter has a user set target operations count which, available via data communications. Typically this is set as a
when reached, can be mapped to raise alarms/ binary rolling value for the last 24 hours.
outputs. A CB Trip Time meter is also available, which
measures the time between the trip or open command being Real Time Clock
issued and the auxiliary contacts changing state. The time and date can be set and are maintained while the
relay is de-energised by a back up storage capacitor. The
Control Mode time can be synchronized from a binary input pulse or the
The relay has a control menu with access to commonly used data communication channel.
command operations (except 7SR1102-1*A12-*AA0
models). Access to the control commands is restricted by a 4
character control function password. Each command Serial Communications
requires a select then execute operation, if the execute
operation is not performed within a time window the
command is aborted. The following control functions are The relay offers a USB serial port as standard on the front of
available: all units. All of the relays functions can be set on a PC using
CB Operation Reydisp Evolution via the USB port. The connection is made
Auto Reclose In/Out with a USB cable and operates with a ‘plug and play’
Auto Reclose Trip & Reclose connection, so no pre-setting of the relay is required.
Auto Reclose Trip & Lockout The front port can be switched off or set to use either the
SEF In/Out DNP3.0, MODBUS-RTU, IEC60870-5-103 and ASCII protocols
Inst Prot In/Out for testing purposes.
Hot Line Working In/Out A rear RS485 electrical connection is available on all units for
system interface connections. An internal terminating
resistor is provided, which can be connected into the circuit
by adding a wire loop between the relevant terminals.

RS485 Screened
Ext Wire loop to
twisted pair
To Control System Include line
terminating Res
14 14
16 16
18 18
20
Screens connected
Fig 8. Example of Control Function View RS485 Screened
externally to de vice
Re ar terminals
twisted pair

Fig 9. Typical RS485 connection


Data Acquisition -
Via Communication Interface The rear RS485 can be user selected to be OFF, IEC60870-5-
103, MODBUS RTU or DNP3.0 protocol.

Sequence of event records IEC 61850


Up to 1000 events are stored and time tagged to 1ms IEC61850 communication is available through an optional
resolution. EN100 communication module. The EN100 Module can be
ordered with either 2x Electrical RJ45 or 2x Fibre optic LC
Fault Records Ethernet ports.
The last 10 fault records are displayed on the relay fascia and Information on IEC61850 functionality can be found in the
are also available through the communication interface, following 7SR11/12 documents:
with time and date of trip, measured quantities and type of Model Implementation Conformance Statement (MICS)
fault. (5 records for 7SR1102-1*A12-*AA0 versions).
Protocol Implementation (PICS,PIXIT & TICS)

Siemens Protection Devices Limited 7


Language Editor
Reydisp Evolution The Language editor software gives the user the ability to
customize the text displayed in the relays, Menu structure
and instrumentation views. The tool allows a language file
Reydisp Evolution is a Windows based software tool,
to be created and transferred to the relay also containing
providing the means for the user to apply settings,
Western European characters.
interrogate settings and retrieve events and disturbance
waveforms from the device and is common to the entire
range of Reyrolle protection relays.

Fig 11. Typical Language Editor Screenshot

Communications Editor
To facilitate easier interfacing to a substation the relays
default Protocol configuration may be modified using the
communication editor software tool.
The communication editor is a PC based software package
provided within the Reydisp software suite which allows
modification of the IEC60870-5-103, DNP 3.0 and MODBUS
Fig 10. Typical Reydisp Evolution Screenshot Protocols.

Fig 12. Typical Communications Editor Screenshot

8 Siemens Protection Devices Limited


Reydisp Manager
Reydisp Manager provides the functionality of Reydisp
Evolution and also provides project management of multiple
devices to allow engineering of IEC61850 projects. It also
provides access to user logic within the devices via an easy to
use graphical interface.

Fig 3. Typical Reydisp Manager screenshots

Siemens Protection Devices Limited 9


Construction
The relay is housed in a 4U high, size E4 or E6 (Optional
IEC61850 model) case with a removable clear fascia cover.
The fascia cover can be ordered with or without two push
buttons to allow the user to view the settings and
instruments without removing the cover.
Two handles are provided to allow the relay to be withdrawn
from its case, contacts in the case ensure that the CT circuits
and normally closed contacts remain short circuited when
the relay is withdrawn.
The rear terminal blocks comprise M4 female terminals for
ring crimp wire connections, to provide a secure and reliable
termination.

Fig 15. Front view of relay (E4 Case with push buttons)

Fig 13. Rear view of relay (E4 Case)

Fig 16. Front view of relay (E6 Case with IEC61850

Fig 14. Rear view of relay with 2x LC Fibre Optic ports


(E6 Case with IEC61850)

10 Siemens Protection Devices Limited


User Interface

User
Function
Label

Large LCD

Multi-
coloured
Programmable
LED’s
from fascia

Fig 17. User Interface

The operator interface is designed to provide a user friendly


method of controlling, viewing menus, entering settings and
retrieving data from the relay. Five buttons are provided for
navigation around the menu structure.

LCD
A 4 line by 20 character liquid crystal display with power
save operation indicates the relay identifier, settings,
instrumentation, fault data and control commands.
Up to 6 user programmable general alarms can be
configured to display your own indications on the LCD.

LEDs
A green steadily illuminated LED indicates the ‘Protection
Healthy’ condition.
9 user programmable LEDs are available eliminating the
need for expensive panel mounted pilot lights and
associated wiring. Each LED is tri-color (red, green, yellow)
allowing for clear indication of the associated function’s
state and has a label insert for identification.

Relay Information
The device is identified by the rating label on the fascia. The
user can also give the device its own identity by editing the
‘Relay Identifier’ displayed on the LCD or space is provided to
place a slip in label giving the relays function.

Siemens Protection Devices Limited 11


Binary Inputs
Technical Data
Number 3,4 or 6
For full technical data refer to the Performance Specification Operating 19V dc DC Range 19 to 320V dc
Section of the Technical Manual. Voltage Minimum threshold 17V dc
88V dc Range 88 to 320V dc
Minimum threshold 68.75V dc
Maximum 1.5mA dc
Inputs and Outputs current for
operation
Pick Up Delay User Selectable 0 to 14,400,000ms
Current Inputs (up to 4 hours)
Drop Off Delay User Selectable 0 to 14,400,000ms
Quantity 3 x Phase & 1 x Earth or (up to 4 hours)
Sensitive Earth
Rated Current In 1/5A Binary Outputs
Measuring Range 80 x In
Instrumentation ≥ 0.1xIn ±1% In Number 5 or 8
Frequency 50/60Hz (3 change over contacts)
Thermal Withstand: Operating Voltage Voltage Free
Continuous 3 x In Operating Mode User selectable - Self or
10 Minutes 3.5 x In Hand/Electrical Reset or pulsed.
2 Minutes 6 x In Operating Time from <20ms
1 Second 100A (1A) 350A (5A) Energizing Binary Input
1 Cycle 700A (1A) 2500A (5A) Making Capacity:
Burden @ In ≤0.02VA (1A phase and Earth Carry continuously 5A ac or dc
element) Make and carry 20A ac or dc for 0.5s
≤0.2VA (5A phase and earth (L/R  40 ms and V  300 30A ac or dc for 0.2s
element) V)
Breaking Capacity
Voltage Inputs (  5 A and  300 V):
AC Resistive 1250 VA
Nominal 40…160 Vrms AC Inductive 250 VA at p.f.  0.4
Operating Range 0… 200 Vrms DC Resistive 75 W
Instrumentation ≥ 0.8xVn ±1% Vn DC Inductive 30 W at L/R  40ms
Burden @ 110V  0.06 VA 50 W at L/R  10ms
Overvoltage Withstand 300 Vrms

Auxiliary Supply
Unit Design
Rated DC Voltage 24-250V DC
Operating Range 19.2 to 275V Housing E4 or E6(see dimension
Allowable superimposed 12% of DC voltage drawing)
ac component Indication 20 Character 4 line Display
Relay Healthy LED
Rated AC Voltage 100-230 VAC 50/60Hz
9 Tri Coloured User
Range 80 to 253 V rms AC
Programmable Self or Hand
50/60Hz ±5%
Reset LED’s
Power Consumption: Min (DC) 3.6W(6.1W with
With-drawable Element Yes
IEC61850)
Max (DC) 8.4W (11W with User Interface 5 Navigation Keys
IEC61850) Weight Typical 3.1Kg
Min (AC) 9VA (14.5VA with IP Rating installed with IP 51 from front
Max (AC) IEC61850) cover
17VA (23VA with IP Rating installed without IP 20 from front
IEC61850) cover
Allowable breaks/dips in DC 50ms
supply (collapse to zero) AC 2.5/3 cycles
@50/60Hz

12 Siemens Protection Devices Limited


Data Communication Interface Mechanical Tests

Communication Port Front USB Type B Vibration (Sinusoidal)


Rear RS485 2 wire electrical IEC 60255-27 & IEC 60255-21-1 Class I
IEC61850 optional ports:
Type Level Variation
2x Electrical RJ45 Ethernet
Vibration response 0.5 gn 5%
2x LC Fibre Optic Ethernet
Vibration response 1.0 gn 5%
Protocols IEC60870-5-103
Shock and Bump
MODBUS RTU (Serial)
IEC 60255-27 & IEC 60255-21-2 Class I
DNP3.0 O (Serial)
IEC61850 - optional Type Level Variation
Fibre Optic Ethernet Data Shock response 5 gn, 11 ms 5%
Communication Interface Shock withstand 15 gn, 11 ms 5%
(IEC 61850 Option) Bump test 10 gn, 16 ms 5%

Seismic
IEC 60255-27 & IEC 60255-21-3 Class I
EN100 Fibre Optic Data Communication Interface
(IEC 61850 Option) Type Level Variation
X-plane -
Physical layer Fibre-optic 3.5mm
displacement
Connectors Duplex LC 100BaseF in acc. below crossover
With IEEE802.3 freq (8-9Hz) 1gn
and above
Recommended fibre 62.5/125 m glass fibre with Seismic response 5%
Y-plane –
Duplex-LC connector
1.5mm
Transmission Speed 100 MBits/s
displacement
Optical Wavelength 1300 nm below crossover
Bridgeable distance freq (8-9Hz)
2 km
0.5gn above

EN100 Electrical Ethernet Data Communication Interface Mechanical Classification


(IEC 61850 Option)
Durability >106 operations
Physical Electrical

Connectors RJ45 100BaseF in acc. With


IEEE802.3
Transmission Speed 100 MBits/s

Test Voltage (with regard to 500 VAC 50 Hz


socket)
Bridgeable distance 20m

Data Storage

Fault Record 10 (5 for 7SR1102-1*A12-*AA0).


Waveform Record 10 x 1sec
2 x 5sec
5 x 2sec
1 x 10sec
(5x1sec, 2x2sec, 1x5sec
for 7SR1102-1*A12-*AA0)
Pre trigger 10…90%
Events 1000 1ms Resolution

Siemens Protection Devices Limited 13


Conducted Radio Frequency Interference Immunity
Electrical Tests IEC 60255-26
Insulation
Type Level Variation
IEC 60255-27
0.15 to 80 MHz 10 V 5%
Type Level
Radiated Radio Frequency Emissions
Between any terminal 2.0 kV AC RMS for 1 min
IEC 60255-26
and earth
Between independent 2.0 kV AC RMS for 1 min Type Limits at 10 m, Quasi-peak
circuits 30 to 230 MHz 40 dB(V)
Across normally open 1.5 kV AC RMS for 1 min 230 to 10000 MHz 47 dB(V)
contacts
Conducted Radio Frequency Emissions
Slow damped Oscillatory Wave (High Frequency
Disturbance) Type Limits
IEC 60255-26 Quasi-peak Average
0.15 to 0.5 MHz 79 dB(V) 66 dB(V)
Type Level Variation 0.5 to 30 MHz 73 dB(V) 60 dB(V)
Common 2.5 kV 5%
(longitudinal) mode Radiated Immunity
Series (transverse) 1.0 kV 5% IEC 60255-26
mode
Type Level
Electrostatic Discharge 80 MHz to 1000 MHz Sweep 10 V/m
IEC 60255-26
1.4GHz to 2.7GHz Sweep 10V/m
Type Level Variation
Front Cover Fitted Class IV, 5% 80,160,380,450,900,1850,2150 10V/m
MHz Spot
15 kV Air Discharge
Front Cover Removed Class III, 5% Power Frequency Immunity
8 kV Air Discharge IEC 60255-26

Fast Transients Type Binary Inputs


IEC 60255-26) Common mode 300 V
Differential mode 150 V
5/50 ns 5 kHz Level Variation
repetitive
Analog Inputs, Aux 4kV 5%
supply & I/O Climatic Tests
RS485 port 2kV 5%
Temperature
Surge Immunity IEC 60255-1 & IEC 60068-2-1/2
IEC 60255-26
Operating Range -10 C to +55 C
Type Level Variation Storage range -25 C to +70 C
Analog Inputs:
4.0 kV  10% Humidity
Line to Earth
Case, Aux Power & IEC 60255-1 & IEC 60068-2-78
2.0 kV  10%
I/O: Line to Earth
Operational test 56 days at 40 C and 93 %
RS485 Comms port: relative humidity
1.0 kV No Data Loss
Line to Earth
Analog Inputs: Cyclic Temperature and Humidity
1.0 kV  10% IEC 60255-1 & IEC 60068-2-30
Line to Line
Case, Aux Power &
1.0 kV *  10% Operational test 25 C to 55 C (outdoor
I/O: Line to Line
equipment) and 97/93 % relative
* Note 50ms DTL pick-up delay applied to binary inputs humidity. 6 x 24h (12h+12h)
cycles.

14 Siemens Protection Devices Limited


37 Undercurrent
Performance
Number of Elements 2 Phase and 2 EF/SEF
27/59 Under/Over Voltage Operate Any phase or ALL
Setting Range Is Phase and EF
0.05,0.10…5.0 x In
Number of Elements 4 Under or Over
SEF
Operate Any phase or All phases 0.005,0.010…5.0 x In
Voltage Guard 1,1.5…200V Operate Level 100% Is, ±5% or ±1%xIn
Setting Range Vs 5,5.5…200V Current Guard Phase 0.05,0.1…5.0 x In
Hysteresis Setting 0.0.1…80% Delay Setting td 0.00,0.01…20,20.5…100,101…
Vs Operate Level 100% Vs, ±1% or ±0.25V 1000,1010…10000,10100…144
Reset Level: 00s
Overvoltage =(100%-hyst)xVop, ±1% Basic Operate Time:
Undervoltage =(100%+hyst)xVop, ±1% 1.1 to 0.5xIn 35ms ±10ms
Delay Setting td 0.00,0.01…20,20.5…100,101… Operate time following Tbasic +td , ±1% or ±10ms
1000,1010…10000,10100…144 delay.
00s Overshoot Time < 40ms
Basic Operate Time :
Inhibited by Binary or Virtual Input
0 to 1.1xVs 73ms ±10ms
0 to 2.0xVs 63ms ±10ms
1.1 to 0.5xVs 58ms ±10ms
46 Negative Phase Sequence Overcurrent
Operate time following Tbasic +td , ±1% or ±10ms
delay.
Inhibited by Binary or Virtual Input Number of Elements DT & IT
VT Supervision DT Setting Range Is 0.05,0.10…4.0 x In
Voltage Guard DT Operate Level 100% Is, ±5% or ±1%xIn
DT Delay Setting td 0.00,0.01…20,20.5…100,101…
32 Power (7SR12) 1000,1010…10000,10100…
14400s
DT Basic Operate Time
Number of Elements 2 Forward or Reverse
0 to 2 xIs 40ms ±10ms
Operate P, Q or S 0 to 5 xIs 30ms ±10ms
U/C Guard 0.05 to 1.0 x In DT Operate time Tbasic +td , ±1% or ±10ms
Setting Range Ss 0.05 to 2.0 x Sn following delay.
Operate Level Sop 100% Ss, ± 5% or ± 2% Sn IT Char Setting IEC NI,VI,EI,LTI ANSI MI,VI,EI &
Reset Level: - ≥95% Sop DTL
Basic Operate Time: - IT Setting Range 0.05..2.5
1.1 x Ss (over) 60ms ± 10ms Tm Time Multiplier 0.025,0.030…1.6,1.7…5,6…100
2.0 x Ss (over) 45ms ± 10ms Char Operate Level 105% Is, ±4% or ±1%In
0.5 x Ss (under) 30ms ± 10ms
Overshoot Time < 40ms
Delay Setting td 0 to 14400s
Inhibited by Binary or Virtual Input
Operate time tbasic +td , ±1% or ±10ms
following delay.
47 Negative Phase Sequence
Inhibited by Undercurrent Guard, VTS

32S Sensitive Power (7SR12 SEF) Number of Elements 2


Setting Range Vs 1,1.5…90V
Hysteresis Setting 0,0.1…80%
Number of Elements 2 Forward or Reverse
Operate Level 100% Vs, ±2% or ±0.5V
Operate P, Q or S
Delay Setting td 0.00,0.01…20,20.5…100,101…
U/C Guard 0.005 to 1.0 x In 1000,1010…10000,10100…
Setting Range Ss 0.005 to 2.0 x Sn 14400s
Operate Level 100% Ss ± 5% or ± 2% Sn Basic Operate Time
Reset Level: - ≥95% Sop 0V to 1.5xVs 80ms ±20ms
Basic Operate Time: - 0V to 10xVs 55ms ±20ms
1.1 x Ss (over) 60ms ± 10ms Operate time following Tbasic +td , ±2% or ±20ms
2.0 x Ss (over) 45ms ± 10ms delay.
0.5 x Ss (under) 30ms ± 10ms Overshoot Time < 40ms
Delay Setting td 0 to 14400s Inhibited by Binary or Virtual Input
Operate time tbasic +td ± 1% or ± 10ms
following delay.
Inhibited by Undercurrent Guard, VTS

Siemens Protection Devices Limited 15


49 Thermal Overload Follower Delay 0 - 20s
Reset ANSI decaying, 0 – 60s
Operate levels Operate and Alarm Inhibited by Binary or Virtual Input
Setting Range Is 0.10,0.11…3.0 x In Inrush detector
Operate Level 100% Is, ±5% or ±1%xIn VT Supervision
Time Constant Setting 1,1.5…1000min
Operate time 
t    In 
I 2  I p2 
 I 2 
2
 k  I B 51V Voltage Controlled Overcurrent
±5% absolute or ±100ms where
Ip = prior current Setting Range 5,5.5…200V
Alarm Level Disabled, 50,51…100% Operate Level 100% Vs, ±5% or ±1%xVn
Inhibited by Binary or Virtual Input Multiplier 0.25.0.3…1 x 51Is
Inhibited by VT Supervision
50 (67) Instantaneous & DTL OC&EF (Directional)

Operation – 7SR12 only Non directional, Forward or 50AFD Arc Flash Detector
reverse
Elements Phase, Derived Earth, Measured Number of Zones 6, segregated outputs with and
Earth & SEF without current supervision.
Number of Elements 2/4 x OC Setting Range Is 1,2…10 x In
2 x 7SR11 2/4 x Derived EF ‘N’ Operate Level Iop 100% Is, ±5% or ±1%xIn
4 x 7SR12 2/4 x Measured EF ‘G’ where Reset level  95 % Iop
fitted
Operate time: 50AFD Overcurrent
2/4 x SEF where fitted
<16ms
AFD Zone Operate Time
Setting Range Is 0.05,0.06…50 x In
<25ms
SEF 0.005…5 x In
Time Delay 0.00…14400s
Operate Level Iop 100% Is, ±5% or ±1%xIn
50BF Circuit Breaker Fail
Reset level  95 % Iop
Operate time: Operation Current check - Phase and
50 0 to 2xIs – 35ms, ±10ms, Measured Earth with
0 to 5xIs – 25ms, ±10ms independent settings
50N 0 to 2xIs – 40ms, ±10ms, Mechanical Trip
0 to 5xIs – 30ms, ±10ms CB Faulty Monitor
Operate time following Tbasic +td , ±1% or ±10ms Setting Range Is 0.05,0.055…2.0 x In
delay 2 Stage Time Delays Timer 1 20…60000ms
Inhibited by Binary or Virtual Input Timer 2 20…60000ms
Inrush detector Operate Level 100% Is, ±5% or ±1%xIn
VT Supervision Disengaging time < 20ms
Operate time following Tcbf ±1% or ±2ms
51(67) Time Delayed OC&EF (Directional) delay
Triggered by Any function mapped as trip
Operation – 7SR12 only Non directional, Forward or contact.
reverse Inhibited by Binary/Virtual Input
Elements Phase, Derived Earth, Measured Timer By pass Yes, 50BF CB Faulty Input
Earth & SEF
Number of Elements 2/4 x OC
2 x 7SR11 2/4 x Derived EF ‘N’ 55 Power factor (7SR12)
4 x 7SR12 2/4 x Measured EF ‘G’
2/4 x SEF where fitted Number of Elements 2
Characteristic IEC NI,VI,EI,LTI ANSI MI,VI,EI & Operation Under or Over,
DTL Lead or Lag
Setting Range Is 0.05,0.06…2.5 x In U/C Guard 0.05 to 1.0
SEF 0.005…0.5 x In
Setting Range PFs 0.05 to 0.99
Time Multiplier 0.025,0.030…1.6,1.7…5,6...100 Time Delays 0 to 14400s
Time Delay 0,0.01… 20s
Operate Level ± 0.05
Operate Level 105% Is, ±4% or ±1%xIn
Basic Operate time ≤ 70ms
Minimum Operate time
Operate time following tbasic +td ± 1% or ± 10ms
IEC top 
K
 Tm delay
IsI   1 Inhibited by Undercurrent Guard, VTS
ANSI  A 
top   P  B Tm
 Is  1 
I

 5 % absolute or  30 ms
16 Siemens Protection Devices Limited
59N Neutral Voltage Displacement 81 Under/Over Frequency

Number of Elements DT & IT Number of Elements 4 Under or Over


DT Setting Range Is 1…100V Under Voltage Guard Yes/No
DT Operate Level 100% Vs, ±2% or ±0.5V Setting Range Hz 43,43.01…68Hz
DT Delay Setting td 0 …14400s Hysteresis Setting 0, 0.1… 2%
DT Basic Operate Time Operate Level 100% Fs ±10mHz
0V to 1.5 x Vs 76ms ±20ms Operate Time Typical <150ms
0V to 10 x Vs 63ms ±20ms Vs Operate Delay 0…14400s
DT Operate time Tbasic +td , ±1% or ±20ms
following delay. Control Functions
IT Char Setting IDMTL & DTL
IT Setting Range 1…100V CB Open/Close
Tm Time 0.1…140 Inst Prot IN/OUT
Multiplier(IDMT) EF IN/OUT
Delay (DTL) 0…20s SEF IN/OUT
Reset ANSI Decaying, 0…60s Hot Line IN/OUT
Char Operate Level 105% Vs, ±2% or ±0.5V Relay Mode Local/Remote/Local or Remote
Inhibited by Binary or Virtual Input Reset LED’s & O/P’s
Not available in 7SR1102-1*A12-*AA0
60 Supervision CB Maintenance

CT 7SR11 Current Trip Counter Total & Delta


7SR12 Current or Vnps & Inps 0…10000
VT nps/zps Counts to AR Block 0…10000
Frequent Operations 0…10000
I2t Alarm 10…100000
64H Restricted Earth Fault

Setting Range SEF input 0.005, 0.006 …


0.100, 0.105 …
0.950 xIn
EF input 0.05, 0.055...
0.95 xIn
Operate Level 100% Is, ±5% or ±1%xIn
Time Delay 0.00… 14400s
Basic Operate Time 0 to 2 xIs 45ms ±10ms
0 to 5 xIs 35ms ±10ms
Inhibited by Binary or Virtual Input

74T/CC Trip/Close Circuit Supervision

Number of supervisable 3 x Trip and 3 x Close


circuits
Number of BI’s Required 1 or 2 per function

79 AutoReclose

Operating Mode Phase, Earth, SEF External


Number of Reclosures 4
Number of Trips 5
Dead Time 0…14400
Reclaim Time 0…600
Lockout Reset CB, Timer & BI

Siemens Protection Devices Limited 17


Case Dimensions
Case Earth
11 31 216.5 connection 103.5

Typical
FRONT
when SIDE VIEW
VIEW
fitted

25mm MIN CLEARANCE FOR TERMINAL WIRING

98.5
Diameter 3.6 - 4 holes (see note)

NOTE:
THE 3.6 HOLES ARE FOR M4 THREAD FORMING (TRILOBULAR) SCREWS.
THESE ARE SUPPLIED AS STANDARD AND ARE SUITABLE FOR USE IN
FERROUS / ALUMINIUM PANELS 1.6mm THICK AND ABOVE. FOR OTHER E4
PANELS, HOLES TO BE M4 CLEARANCE (TYPICALLY 4.5 DIAMETER) AND PANEL CUT-
RELAYS MOUNTED USING M4 MACHINE SCREWS, NUTS AND OUT
LOCKWASHERS (SUPPLIED IN PANEL FIXING KIT).

10.25 78
Fig 18. E4 Case Dimensions

Fig 19. E6 Case Dimensions

18 Siemens Protection Devices Limited


7SR11 Connection Diagram

Alternative 4BI+8BO
2
+ve B +ve
3 without common terminals
-ve BI 1 BI 4 -ve +ve
4 1 3
+ve +ve BI 4 -ve
6 5 1
BI 2 BI 5
-ve
8 5
+ve +ve
10 7 BO 6 7
-ve BI 3 BI 6
12 9

9 BO 7 11
14 A
BO 6 11 13
16 Screen
BO 7 13 BO 8 15
18 B
BO 8 15
20 Term. B
+ve
22
-ve
24
1 2 1 2
28 GND.

IEC61850
Data B A
1A Comms
13
A 3
(Optional)
14 BO 1 1
5A IL1
15 2

16 4 27 28 27 28
1A
17 BO 2 6
Rear View
18 5 Arrangement of terminals and modules
5A IL2
19

20
8
1A BO 3 NOTES
21
7
22 BI = Binary Input
5A IL3 10 BO = Binary Output
23 BO 4
9
24
1A 12
25 BO 5
11 Shows contacts internal to relay
26
IL4
case assembly.
5A
27 Contacts close when the relay
28 chassis is withdrawn from case

Fig20. Diagram showing 7SR11 relay with 4 CT inputs, up to 6 binary inputs and 8 binary outputs.

Siemens Protection Devices Limited 19


7SR12 Connection Diagram

RS485

Fig21. Diagram showing 7SR12 relay with 4 CT inputs, 3 VT inputs, up to 6 binary inputs and 8 binary outputs.

20 Siemens Protection Devices Limited


Ordering Information – 7SR11 Argus Non-Directional Overcurrent

Product description Variants Order No.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nondirectional O/C Relay (Argus) 7 S R 1 1 0 □ - □□ A □□ - □ □ A 0

Overcurrent and earth fault


Protection relay
Protection Product
Overcurrent – Non Directional 1

Housing I/O and Fascia


1 CT, 3 Binary Inputs / 5 Binary Outputs, 10 LEDs 1 1 C
4 CT, 3 Binary Inputs / 5 Binary Outputs, 10 LEDs 2 A/C/D
4 CT, 6 Binary Inputs / 8 Binary Outputs, 10 LEDs 3 C/D
4 CT, 4 Binary Inputs / 8 Binary Outputs, 10 LEDs 7) 7 C/D

Measuring Input
1/5 A, 50/60Hz1) 1 A/C/D
1/5 A, 50/60Hz with SEF Input 2) 3 C/D

Auxiliary voltage
PSU Rated: 24-250V DC / 100-230V AC. BI threshold 19V DC (Rated: 24-250V DC) M
PSU Rated: 24-250V DC / 100-230V AC. BI threshold 88V DC (Rated: 110-250V DC) N

Communication Interface
Standard version – included in all models, USB front port, RS485 rear port (E4 Case) 1 2
Standard version – plus additional rear electrical Ethernet RJ45 (x2), E6 Case 6) 7 7 C/D
Standard version – plus additional rear optical Ethernet duplex (x2), E6 Case 6 ) 8 7 C/D

Protocol
IEC 60870-5-103 Modbus RTU and DNP3 (user selectable) 2
IEC 60870-5-103 Modbus RTU, DNP3 and IEC 61850 (user selectable settings) 6) 7

Relay Cover
Standard Version – No Push Buttons 1
Push Buttons – Down and Right Arrows 2

Protection Function Packages


Basic version 5) A
46BC3) Broken conductor/load unbalance
503) Instantaneous phase fault overcurrent
50BF3) Circuit breaker fail
50G/50N Instantaneous earth fault
513) Time delayed phase fault overcurrent
51G/51N Time delayed earth fault
60CTS3) CT Supervision
64H High impedance REF
74T&C Trip & Close circuit supervision
86 Hand reset contacts

Standard version C
37 Undercurrent
46BC3) Broken conductor/load unbalance
46NPS3) Negative phase sequence overcurrent
493) Thermal overload
503) Instantaneous phase fault overcurrent
50AFD Arc Flash Detection
50BF3) Circuit breaker fail
50G/50N Instantaneous earth fault
50SEF2) Instantaneous sensitive earth fault
513) Time delayed phase fault overcurrent
51G/51N Time delayed earth fault
51SEF2) Time delayed sensitive earth fault
60CT3) CT Supervision
64H High Impedance REF
74T/CC Trip and Close circuit supervision
81HBL2 4) 2nd harmonic block/inrush restraint
51C3) Cold load pickup
86 Hand reset contacts
Programmable logic

(continued on next page)

Siemens Protection Devices Limited 21


Ordering Information – 7SR11 Argus Non-Directional Overcurrent

Product description Variants Order No.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nondirectional O/C Relay (Argus) 7 S R 1 1 0 - A - A 0

continued from previous page

Standard version – plus D


79 Autoreclose

Additional Functionality

No Additional Functionality A

1) 4CT is configured as 3PF + EF


2) 4CT is configured as 3PF + SEF/REF.
3) Functions only available in 4CT relay
4) Not available on SEF input
5) Protection function package ordering option A is only available on hardware variant 7SR1102-1XA12-XAA0- 4CT 3BI 5BO
6) E4 case is standard, E6 case is required if IEC61850 model ordered
7) 4 Binary Input variant provides segregated Binary Outputs without a common terminal

22 Siemens Protection Devices Limited


Ordering Information – 7SR12 Argus Directional Overcurrent
Product description Variants Order No.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Directional O/C 7 S R 1 2 0 - A - A 0
Relay (Argus)

Directional
overcurrent
and earth fault Protection Product
protection relay Overcurrent – Directional 2

Housing I/O and Fascia


1 CT, 3 VT, 3 Binary Inputs / 5 Binary Outputs, 10 LEDs 4 1 C
4 CT, 3 VT, 3 Binary Inputs / 5 Binary Outputs, 10 LEDs 5
4 CT, 3 VT, 6 Binary Inputs / 8 Binary Outputs, 10 LEDs 6
4 CT, 3 VT, 4 Binary Inputs / 8 Binary Outputs, 10 LEDs 6) 8

Measuring Input
1/5 A, 40 to 160 V, 50/60Hz1) 2
1/5 A, 40 to 160 V, 50/60Hz with SEF Input2) 4

Auxiliary voltage
PSU Rated: 24-250V DC / 100-230V AC. BI threshold 19V DC (Rated: 24-250V DC) M
PSU Rated: 24-250V DC / 100-230V AC. BI threshold 88V DC (Rated: 110-250V DC) N

Communication Interface
Standard version – included in all models, USB front port, RS485 rear port (E4 Case) 1 2
Standard version – plus additional rear electrical Ethernet RJ45 (x2), E6 Case 5) 7 7
Standard version – plus additional rear optical Ethernet duplex (x2), E6 Case 5 ) 8 7

Protocol
IEC 60870-5-103, Modbus RTU and DNP3 (user selectable) 2
IEC 60870-5-103 Modbus RTU, DNP3 and IEC 61850 (user selectable settings) 5) 7

Relay Cover
Standard Version – No Push Buttons 1
Push Buttons – Down and Right Arrows 2

Protection Function Packages


Standard version – Included in all models C
27/59 Under/overvoltage
323) Power
32S7) Sensitive Power
37 Undercurrent
46BC3) Broken conductor/load unbalance
46NPS3) Negative phase sequence overcurrent
47 Negative phase sequence voltage
493) Thermal overload
50AFD Arc Flash Detection
50BF3) Circuit breaker fail
51V3) Voltage controlled overcurrent
553) Power Factor
59N Neutral voltage displacement
60CTS3) CT supervision
60VTS 3) VT supervision
64H High Impedance REF
67/50 Directional instantaneous phase fault overcurrent
67/50G 67/50N Directional instantaneous earth fault
67/50SEF 2) Instantaneous sensitive earth fault
67/51 Directional time delayed phase fault overcurrent
67/51G 67/51N Directional time delayed earth fault
67/51/SEF2) Time delayed sensitive earth fault
81HBL2 4) 2nd harmonic block/inrush restraint
74T/CC Trip & Close circuit supervision
51C3) Cold load pickup
81U/0 Under/Over Frequency
86 Hand reset contacts
Programmable logic

Standard version – plus D


79 Autoreclose

Additional Functionality

No Additional Functionality A

1) 4CT is configured as 3PF + EF


2) 4CT is configured as 3PF + SEF/REF
3) Functions only available in 4CT relay
4) Not available on SEF input
5) E4 case is standard, E6 case is required if IEC61850 model ordered
6) 4 Binary Input variant provides segregated Binary Outputs without a common terminal
7) Functions only available in 4CT SEF relay

Siemens Protection Devices Limited 23


Published by and copyright © 2022:
Siemens Protection Devices
P.O. Box 8
North Farm Road
Hebburn
Tyne & Wear
NE31 1TZ
United Kingdom
Phone: +44 (0)191 401 7901
E-mail: [email protected]

EMEA-C10028-00-76GB

Sept 2022

For enquires please contact our Customer Support Center


Phone: +49 180/524 8437 (24hrs)
Fax: +49 180/524 24 71
E-mail: [email protected]
www.siemens.com/protection

Subject to change without notice, Printed in the UK.

www. siemens.com/energy

24 Siemens Protection Devices Limited

You might also like