SPR6LU100EN0

libretto U100
TOSHIBA
libretto U100
Portable Personal Computer
User’s Manual
Copyright
© 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.
TOSHIBA libretto U100 Portable Personal Computer User’s Manual
First edition April 2005
Copyright authority for music, movies, computer programs, data bases and
other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author’s rights and is subject
to civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.
Disclaimer
This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
libretto U100 Portable Personal Computer at the time of this manual’s
production. However, succeeding computers and manuals are subject to
change without notice. TOSHIBA assumes no liability for damages incurred
directly or indirectly from errors, omissions or discrepancies between the
computer and the manual. Graphics processor performance may vary
considerably from specifications due to design configuration.
Trademarks
IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.
Intel, Intel SpeedStep, Pentium and Centrino are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the United States and
other countries/regions.
Windows and Microsoft are registered trademarks of Microsoft Corporation.
Photo CD is a trademark of Eastman Kodak.
Sonic RecordNow! is registered trademarks of Sonic Solutions.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.
i.LINK is trademark and registered trademark of Sony Corporation.
InterVideo and WinDVD are registered trademarks of InterVideo Inc.
WinDVD Creator is trademark of InterVideo Inc.
Other trademarks and registered trademarks not listed above may be used
in this manual.
ii User’s Manual
EU Declaration of Conformity
TOSHIBA declares, that the product: PLU10* conforms to the following
Standards:
Supplementary This product is labelled with the CE
Information: Mark in accordance with the related
European Directives, notably
Electromagnetic Compatibility Directive
89/ 336/EEC for the notebook and the
electronic accessories including the
supplied power adapter, the Radio
Equipment and Telecommunications
Terminal Equipment Directive 99/5/EEC
in case of implemented
telecommunication accessories and the
Low Voltage Directive 73/23/EEC for the
supplied power adapter.
CE Marking is the responsibility of TOSHIBA EUROPE GmbH,
Hammfelddamm 8, 41460 Neuss, Germany, phone +49-(0)-2131-158-01.
For a copy of the related CE Declaration of Conformity please refer to the
following website: http://epps.toshiba-teg.com.
Modem warning notice

Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for
pan-European single terminal connection to the Public Switched Telephone
Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in the
first instance.
User’s Manual iii

Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.
Germany ATAAB AN005,AN006,AN007,AN009,AN010
and DE03,04,05,08,09,12,14,17
Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and
P03,04,08,10
Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
All other countries/regions ATAAB AN003,004
Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.
iv User’s Manual
Optical disc drive safety instructions
Be sure to check the international precautions at the end of this section.
Panasonic
DVD-ROM and CD-R/RW UJDA765
■ The DVD-ROM and CD-R/RW drive employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.
User’s Manual v
DVD Super Multi UJ-822
■ The DVD Super Multi drive employs a laser system. To ensure proper
use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.
vi User’s Manual
International precautions
CAUTION: This appliance contains a

laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.
CLASS 1 LASER PRODUCT VORSICHT: Dieses Gerät enthält ein

LASERSCHUTZKLASSE 1 Laser-System und ist als
PRODUKT “LASERSCHUTZKLASSE 1 PRODUKT”
TOEN60825 klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch
und bewahren diese bitte als Referenz
auf. Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste “autorisierte Service-Vertretung”.
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.
ADVERSEL: USYNLIG ADVARSEL: Denne mærking er anbragt

LASERSTRÅLING VED udvendigt på apparatet og indikerer, at
ÅBNING, NÅR apparatet arbejder med laserstråler af
SIKKERHEDSAF-BRYDER klasse 1, hviket betyder, at der anvendes
ER UDE AF FUNKTION. laserstrlier af svageste klasse, og at man
UNDGÅ UDSÆTTSLSE ikke på apparatets yderside kan bilve
FOR STRÅLING
udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED
LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som
advarer imod at foretage sådanne
indgreb i apparatet, at man kan komme til
at udsatte sig for laserstråling.
User’s Manual vii

OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.
CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR
FOLGE HABEN.
viii User’s Manual

libretto U100
Table of Contents
General Precautions
Preface
Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Chapter 1 : Introduction
Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Special features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Chapter 2 : The Grand Tour
Front with the display closed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Underside. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Chapter 3 : Getting Started
Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Restarting the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Restoring your preinstalled software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
User’s Manual ix
Chapter 4 : Operating Basics
TOSHIBA Pointing Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Using the USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
Writing CDs on DVD-ROM and CD-R/RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-14
Writing CD/DVDs on DVD Super Multi drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-16
Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-24
Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-26
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27
Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-32
LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-35
Cleaning the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37
Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37
Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-38
Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-41
Chapter 5 : The Keyboard
Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
Chapter 6 : Power and Power-Up Modes
Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
Care and use of the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-12
TOSHIBA Password Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15
Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-16
Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17
System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17
Chapter 7 : HW Setup
Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
HW Setup window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
x User’s Manual
Chapter 8 : Optional Devices
PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
SD card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Universal AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
libretto DVD Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Chapter 9 : Troubleshooting
Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Disposing of PC and PC batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
Chapter 10 : Disclaimers
LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
CPU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Copy Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
HDD Drive Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
Non-applicable Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
Wireless LAN/Atheros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
SRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Express Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
LCD Brightness and Eye Stain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Graphics Processor Unit (“GPU”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
General Main Memory Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Battery Life Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Appendix A : Specifications
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Appendix B : Display Controller and Modes
Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Display settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Appendix C : AT Commands
Appendix D : S-registers
S-register values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
AT command set result codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
User’s Manual xi
Appendix E : V.90
V.90 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
AT Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
Appendix F : Wireless LAN
Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2
Supported Frequency Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2
Appendix G : AC Power Cord and Connectors
Certification agencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
Appendix H : If your computer is stolen
Glossary
Index
xii User’s Manual

libretto U100
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and

withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.
Be certain to read the general precautions below and to note the cautions
included in the text of the manual.
Stress injury
Carefully read the Instruction Manual for Safety & Comfort. It contains
information on prevention of stress injuries to your hands and wrists than
can be caused by extensive keyboard use. Chapter 3, Getting Started, also
includes information on work space design, posture and lighting that can
help reduce physical stress.
Heat injury
■ Avoid prolonged physical contact with the computer. If the computer is
used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time (if you rest the computer on
your lap, or if you keep your hands on the palm rest, for example) your
skin might suffer low-heat injury.
■ If the computer has been used for a long time, avoid direct contact with
the metal plate supporting the I/O ports. It can become hot.
■ The surface of the AC adaptor can become hot when in use. This
condition does not indicate a malfunction. If you need to transport the
AC adaptor, disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat.
The material could be damaged.
User’s Manual xiii

General Precautions
Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components
or otherwise cause malfunctions.
PC card overheating
Some PC cards can become hot with prolonged use. Overheating of a PC
card can result in errors or instability in the PC card operation. Also be
careful when you remove a PC card that has been used for a long time.
Mobile phone
Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but it is recommended that a distance of 30 cm be
maintained between the computer and a mobile phone in use.
xiv User’s Manual

libretto U100
Preface
Congratulations on your purchase of the libretto U100 computer. This

powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.
This manual tells how to set up and begin using your libretto U100
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.
If you are a new user of computers or if you’re new to portable computing,
first read over the Introduction and The Grand Tour chapters to familiarize
yourself with the computer’s features, components and accessory devices.
Then read Getting Started for step-by-step instructions on setting up your
computer.
If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the
Special features section of the Introduction, to learn about features that are
uncommon or unique to the computers and carefully read HW Setup.
If you are going to install PC cards or connect external devices such as a
monitor, be sure to read Chapter 8, Optional Devices.
Manual contents
This manual is composed of the following ten chapters, eight appendixes,
a glossary and an index.
Chapter 1, Introduction, is an overview of the computer’s features,
capabilities, and options.
Chapter 2, The Grand Tour, identifies the components of the computer and
briefly explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin
operating your computer and gives tips on safety and designing your work
area.
User’s Manual xv
Preface
Chapter 4, Operating Basics, includes instructions on using the following

devices: pointing device, fingerprint sensor, USB floppy disk drive,
optical media drives, sound system, modem, wireless communication
features, LAN. It also provides tips on care of the computer, floppy disks
and CD/DVDs.
Chapter 5, The Keyboard, describes special keyboard functions including
the keypad overlay and hot keys.
Chapter 6, Power and Power-Up Modes, gives details on the computer’s
power resources and battery save modes and how to set a password.
Chapter 7, HW Setup, explains how to configure the computer using the
HW Setup program.
Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform
some diagnostic tests, and suggests courses of action if the computer
doesn’t seem to be working properly.
Chapter10, Disclaimers, provides disclaimer information related to your
computer.
The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of
acronyms used in the text.
The Index quickly directs you to the information contained in this manual.
Conventions
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.
Keys
The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.
xvi User’s Manual

Preface
Key operation
Some operations require you to simultaneously use two or more keys.
We identify such operations by the key top symbols separated by a plus
sign (+). For example, Ctrl + C means you must hold down Ctrl and at the
same time press C. If three keys are used, hold down the first two and at
the same time press the third.
ABC When procedures require an action such as

clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
type face you see to the left.
Display
Names of windows or icons or text generated by

S ABC the computer that appears on its display screen is
presented in the type face you see to the left.
Messages
Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.
Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.
Please read. A note is a hint or advice that helps you make best use of
your equipment.
Indicates a potentially hazardous situation, which could result in death or

serious injury, if you do not follow instructions.
User’s Manual xvii

Preface
xviii User’s Manual

libretto U100
Chapter 1
Introduction
This chapter provides an equipment checklist, and it identifies the

computer’s features, options and accessories.
Some of the features described in this manual may not function properly if
you use an operating system that was not preinstalled by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for
future use.
Hardware
Check to make sure you have all the following items:
■ libretto U100 Portable Personal Computer
■ AC adaptor and power cord (2-pin plug or 3-pin plug)
■ USB floppy disk drive *
■ Battery pack
■ libretto DVD Dock *
■ Mini-RGB cable *
■ Spare AccuPoint (pointing device) caps *
* indicates an optional part that is dependant on the model purchased
User’s Manual 1-1

Introduction
Software
Microsoft® Windows XP Professional

■ The following software is preinstalled:
■ Microsoft® Windows XP Professional
■ Microsoft Internet Explorer
■ TOSHIBA Utilities
■ TOSHIBA SD Memory Boot Utility
■ DVD Video Player
■ TOSHIBA Power Saver
■ TOSHIBA Assist
■ TOSHIBA ConfigFree
■ TOSHIBA Zooming Utility
■ TOSHIBA PC Diagnostic Tool
■ TOSHIBA Virtual Sound
■ TOSHIBA Controls
■ Online manual
Microsoft® Windows XP Home Edition

■ The following software is preinstalled:
■ Microsoft® Windows XP Home Edition
■ Microsoft Internet Explorer
■ TOSHIBA Utilities
■ TOSHIBA SD Memory Boot Utility
■ DVD Video Player
■ TOSHIBA Power Saver
■ TOSHIBA Assist
■ TOSHIBA ConfigFree
■ TOSHIBA Zooming Utility
■ TOSHIBA PC Diagnostic Tool
■ TOSHIBA Virtual Sound
■ TOSHIBA Controls
■ Online manual
1-2 User’s Manual

Introduction
Documentation, backup media and additional software

■ libretto U100 Portable Personal Computer User’s Manual
■ libretto U100 Quickstart
■ Microsoft Windows XP manual package *
■ Instruction Manual for Safety & Comfort
■ End User License Agreement
■ Product Recovery Disc *
■ Additional Software CD *
■ Express Media Player Recovery CD *
* indicates an optional part that is dependant on the model purchased
If any of the items are missing or damaged, contact your dealer
immediately.
User’s Manual 1-3

Introduction
Features
The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),
Complementary Metal-Oxide Semiconductor (CMOS) technology
extensively to provide compact size, minimum weight, low power usage,
and high reliability. This computer incorporates the following features and
benefits:
Processor*2
Built-in The computer is equipped with an Intel®
processor.
Intel® Pentium® M processor, which incorporates
a 2 MB level 2 cache memory and supports
Enhanced Intel® SpeedStepTM technology.
Disclaimer (CPU)
Central Processing Unit (“CPU”) Performance Disclaimer.
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use of battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of computer in areas with low air pressure
(high altitude > 1,000 meters or > 3,280 feet above sea level)
■ use of computer at temperatures outside the range of 5°C to 30°C
(41°F to 86°F) or > 25°C (77°F) at high altitude (all temperature
references are approximate and may vary depending on the specific
computer model - please refer to your PC documentation or visit the
Toshiba website at www.pcsupport.toshiba.com for details).
1-4 User’s Manual

Introduction
CPU performance may also vary from specifications due to design

configuration.
Under some conditions, your computer product may automatically
shut-down. This is a normal protective feature designed to reduce the risk
of lost data or damage to the product when used outside recommended
conditions. To avoid risk of lost data, always make back-up copies of data
by periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions under “Environmental Conditions”
in your PC documentation. Contact Toshiba technical service and support,
refer to TOSHIBA support section in Chapter 9 Troubleshooting for more
information.
Memory
Built-in 256 MB of memory is installed on the main
board.
Slots The slot accepts a 256, 512 or 1,024 MB memory
module for a maximum of 1,280 MB system
memory.
Disclaimer (General Main Memory Disclaimer)

The graphics system in your computer may use part of the main system
memory for graphics performance and therefore reduce the amount of
system memory available for other computing activities. The amount of
system memory allocated to support graphics may vary depending on the
graphics system, applications utilized, system memory size and other
factors.
Video RAM Part of system memory is used for Video RAM.

64 MB of RAM is provided for video display.
Power
Battery pack The computer is powered by one rechargeable
lithium-ion battery pack.
User’s Manual 1-5

Introduction
Disclaimer (Battery Life)

Battery life may vary considerably depending on product model,
configuration, applications, power management settings and features
utilized, as well as the natural performance variations produced by the
design of individual components. Published battery life numbers are
achieved on select models and configurations tested by Toshiba at the
time of publication. Recharge time varies depending on usage. Battery
may not charge while computer is consuming full power. After a period of
time, the battery will lose its ability to perform at maximum capacity and will
need to be replaced. This is normal for all batteries. To purchase a new
battery pack, see the accessories information that shipped with your
computer.
RTC battery The internal RTC battery backs up the Real Time
Clock (RTC) and calendar.
AC adaptor The AC adaptor provides power to the system
and recharges the batteries when they are low.
It comes with a detachable power cord which will
either have a 2-pin or 3-pin plug enclosure.
Because it is universal, it can receive a range of
AC voltage from 100 to 240 volts; however,
the output current varies among different models.
Using the wrong model can damage your
computer. Refer to the AC adaptor section in
Chapter 2, The Grand Tour.
Disks
Hard disk drive*4 Available in two sizes.
■ 30.0 billion bytes (27.95 GB)
■ 60.0 billion bytes (55.89 GB)
Disclaimer (HDD Drive Capacity)

1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes using
powers of 10. The computer operating system, however, reports storage
capacity using powers of 2 for the definition of
1 GB = 1024 × 1024 × 1024 = 1,073,741,824 bytes, and therefore may
show less storage capacity. Available storage capacity will also be less if
the product includes one or more pre-installed operating systems, such as
Microsoft Operating System and/or pre-installed software applications,
or media content. Actual formatted capacity may vary.
USB floppy disk Accommodates either 3 1/2" 1.44-megabyte or

drive 720-kilobyte floppy disks. It connects to a USB
port. Option or provided with some models.
1-6 User’s Manual

Introduction
DVD-ROM and Some models are equipped with a full-size,

CD-R/RW drive DVD-ROM and CD-R/RW drive module that lets
you run CD/DVDs without using an adaptor.
It reads DVD-ROMs at maximum 8 speed and
CD-ROMs at maximum 24 speed. It writes CD-R
at maximum 24 speed and CD-RW at
maximum 24 speed. The drive supports the
following formats:
■ DVD-ROM
■ DVD-Video
■ CD-DA
■ CD-Text
■ Photo CD™ (single/multi-session)
■ CD-ROM Mode 1, Mode 2
■ CD-ROM XA Mode 2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
■ Addressing Method 2
■ CD-R
■ CD-RW
DVD Super Multi Some models are equipped with a full-size DVD
drive Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CD/DVDs without
using an adaptor. It reads DVD-ROMs at
maximum 8 speed and CD-ROMs at maximum
24 speed. It writes CD-R at maximum 24 speed,
CD-RW at maximum 10 speed, DVD-R at
maximum 2 speed, DVD-RW at maximum
2 speed. DVD+R and DVD+RW at maximum
2.4 speed. DVD-RAM at maximum 2 speed.
This drive supports the following formats in
addition to DVD-ROM and CD-R/RW drive.
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ DVD-RAM
■ The optical media drive is optional.

■ The optical media drive can be used by connecting libretto DVD Dock
to this computer.
User’s Manual 1-7

Introduction
Display
The computer’s LCD display panel supports high-resolution video graphics.
The LCD screen can be set at a wide range of viewing angles for maximum
comfort and readability.
Built-in*1 7.2” TFT LCD screen 16 M colors, with a
resolution of 1280 horizontal × 768 vertical pixels
WXGA.
Disclaimer (LCD)
Over a period of time, and depending on the usage of the computer,
the brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode.
The screen will dim when the computer is operated on battery power and
you will not be able to increase the brightness of the screen.
Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and
Modes section in Appendix B for more
information.
Disclaimer (Graphics Processor Unit (“GPU”))

Graphics processor unit (“GPU”) performance may vary depending on
product model, design configuration, applications, power management
settings and features utilized. GPU performance is only optimized when
operating in AC power mode and may decrease considerably when
operating in battery power mode.
Keyboard
Built-in 84 keys or 85 keys, compatible with IBM®
enhanced keyboard, embedded numeric overlay,
dedicated cursor control, and keys.
Refer to Chapter 5, The Keyboard, for details.
Pointing Device
Built-in AccuPoint This pointer control stick, located in the center of

the palm rest, provides convenient control of the
cursor.
1-8 User’s Manual

Introduction
Ports
Mini-RGB Analog VGA port supports VESA DDC2B

compatible functions.
Universal Serial Bus The computer has Universal Serial Bus ports that
(USB 2.0) comply with the USB 2.0 standard, which
enables data transfer speeds 40 times faster
than the USB 1.1 standard (The ports also
support USB 1.1).
Docking port This port enables connection of an optional
libretto DVD Dock described in the Options
section.
i.LINK™ (IEEE1394) This port enables high-speed data transfer
directly from external devices such as digital
video cameras.
Slots
PC card The PC card slot accommodate a Type II card.
SD card This slot lets you easily transfer data from
devices, such as digital cameras and
Personal Digital Assistants, that use SD card
flash-memory.
Refer to Chapter 8, Optional Devices.
Multimedia
Sound system The Windows sound system compatible sound
system provides output to internal speakers as
well as supporting jacks for an external
microphone and headphones.
Headphone jack A 3.5 mm mini headphone jack enables
connection of stereo headphones.
Microphone jack A 3.5 mm mini microphone jack enables
connection of a three-conductor mini jack for
monaural microphone input.
User’s Manual 1-9

Introduction
Communications
Modem An internal modem provides capability for data

and fax communication. It supports V.90 (V.92).
Refer to V.90 section in Appendix E. The speed
of data transfer and fax depends on analog
telephone line conditions. It has a modem jack
for connecting to a telephone line. It is
preinstalled as a standard device in some
markets. Both of V.90 and V.92 are supported
only in USA, Canada and Australia. Only V.90 is
available in other regions.
LAN The computer has built-in support for Ethernet
LAN (10 megabits per second, 10BASE-T), and
Fast Ethernet LAN (100 megabits per second,
100BASE-TX).
It is preinstalled as a standard device in some
markets.
Bluetooth Some computers in this series are equipped with
Bluetooth functions. Bluetooth wireless
technology eliminates the need for cables
between electronic devices such as computers
and printers. Bluetooth provides fast, reliable,
and secure wireless communication in a small
space.
1-10 User’s Manual

Introduction
Wireless LAN*6 Some computers in this series are equipped with

a Wireless LAN mini-PCI card that is compatible
with other LAN systems based on Direct
Sequence Spread Spectrum/Orthogonal
Frequency Division Multiplexing radio technology
that complies with the IEEE 802.11 Standard
(Revision B or G), and Turbo Mode. Refer to
Wireless LAN section in Appendix F.
■ Theoretical maximum speed: 54Mbps
(IEEE 802.11g)
(IEEE802.11b)
(Turbo Mode)
■ Frequency Channel Selection
(2.4 GHz: Revision B/G)
■ Roaming over multiple channels
■ Card Power Management
■ Atheros Super GTM technology.
■ Wired Equivalent Privacy (WEP) data
encryption, based on 152 bit encryption
algorithm.
■ Advanced Encryption Standard (AES) data
encryption, based on 256 bit encryption
algorithm.
■ Wi-Fi Protected Access (WPA).
■ The values shown above are the theoretical maximums for wireless
LAN standards. The actual values may differ.
■ The transmission speed over the Wireless LAN and the distance over
which Wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The transmission rate described is the theoretical maximum speed as
specified under the appropriate standard - the actual transmission
speed will be lower than the theoretical maximum speed.
User’s Manual 1-11

Introduction
Disclaimer (Wireless LAN/Atheros)

The transmission speed over the wireless LAN and the distance over
which wireless LAN can reach may vary depending on surrounding
[54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g)
standard.] The actual transmission speed will be lower than the theoretical
maximum speed.
To use the Atheros Super AGTM or Super GTM function, your client and
access point must support the corresponding feature. Performance of
these functions may vary depending on the format of data transmitted.
Wireless This switch turns the Wireless LAN and

communication Bluetooth functions on and off.
switch All models are provided with Wireless
Communication switch. Some models are equipped
with both Wireless LAN and Bluetooth functions.
Special features
The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.
Hot keys Key combinations let you quickly change the
system configuration directly from the keyboard
without running a system configuration program.
Display automatic This feature automatically cuts off power to the
power off computer’s LCD display panel when there is no
keyboard input for a time specified. Power is
restored when any key is pressed. You can
specify the time in the Monitor power off item of
the Basic Setup tab in TOSHIBA Power Saver.
HDD automatic This feature automatically cuts off power to the
power off hard disk drive when it is not accessed for a time
specified. Power is restored when the hard disk is
accessed. You can specify the time in the HDD
power off item of the Basic Setup tab in TOSHIBA
Power Saver.
System automatic This feature automatically shuts down the system
Standby/Hibernation in Standby mode or Hibernation mode when there
is no input or hardware access for a time
specified. You can specify the time and select
either the System Standby or System Hibernation
item of the Basic Setup tab in TOSHIBA Power
Saver.

Introduction
Keypad overlay A ten-key pad is integrated into the keyboard.

Refer to the Keypad overlay section in Chapter 5,
The Keyboard, for instructions on using the
keypad overlay.
Power on password Two levels of password security, supervisor and
user, are available to prevent unauthorized
access to your computer.
Instant security A hot key function blanks the LCD screen and
disables the computer providing data security.
Intelligent power A microprocessor in the computer’s intelligent
supply power supply detects the battery’s charge and
calculates the remaining battery capacity. It also
protects electronic components from abnormal
conditions, such as voltage overload from an AC
adaptor. You can monitor remaining battery
capacity. Use the Battery remaining item in
TOSHIBA Power Saver.
Battery save mode This feature lets you save battery power. You can
specify the Power Save Mode in the Profile item
in TOSHIBA Power Saver.
Panel power on/off This feature turns power to the computer off
when the computer’s LCD display panel is closed
and turns it back on when the computer’s LCD
display panel is opened. You can specify the
setting in the When I close the lid item of the
Setup Action tab in TOSHIBA Power Saver.
Low battery When battery power is exhausted to the point that
automatic computer operation cannot be continued, the
hibernation system automatically enters Hibernation and
shuts down. You can specify the setting in the
Heat dispersal To protect from overheating, the CPU has an

internal temperature sensor. If the computer’s
internal temperature rises to a certain level, the
cooling fan is turned on or the processing speed
is lowered. Use the Cooling Method item of the
Basic Setup tab in TOSHIBA Power Saver.
HDD Protection Using the acceleration sensor built into the

computer, HDD Protection detects vibration and
shock, and automatically moves the hard disk
drive read/write head to a safe position in order to
reduce the risk of damage that could be caused
by head-to-disk contact.

Introduction
The HDD Protection function does not guarantee that the hard disk drive
will not be damaged.
Hibernation This feature lets you turn off the power without
exiting from your software. The contents of main
memory are saved to the hard disk, when you
turn on the power again, you can continue
working right where you left off. Refer to the
Turning off the power section in Chapter 3,
Getting Started, for details.
Standby If you have to interrupt your work, you can turn off
the power without exiting from your software.
Data is maintained in the computer’s main
memory. When you turn on the power again,
you can continue working right where you left off.
Utilities
This section describes preinstalled utilities and tells how to start them.
For details on operations, refer to each utility’s online manual, help files or
readme.txt files.
TOSHIBA Power To access this power savings management

Saver program, click start, click Control Panel, click
Performance and Maintenance and select the
TOSHIBA Power Saver icon.
HW Setup This program lets you customize your hardware
settings according to the way you work with your
computer and the peripherals you use. To start
the utility, To access this utility, click start, click
Control Panel, click Printers and Other
Hardware and select the TOSHIBA HWSetup
icon.
DVD Video Player The DVD Video Player is used to play
DVD-Video. It has an on-screen interface and
functions. Click start, point to All Programs,
point to InterVideo WinDVD, then click
InterVideo WinDVD.

Introduction
Fingerprint utility This product has a fingerprint utility installed for

the purpose of enrolling and recognizing
fingerprints. By enrolling the ID and password to
the fingerprint authentication device, it is no
longer necessary to input the password from the
keyboard. Just by swiping the finger against the
fingerprint sensor, the following functions will be
enabled:
■ Logon to Windows and access a
security-enabled homepage through IE
(Internet Explorer).
■ Files and folders can be encrypted/decrypted
and third party access to them prevented.
■ Disable the password-protected screen-saver
when returning from power-saving (standby)
mode.
TOSHIBA Quick The Fingerprint Sensor can be used to display
Launcher the start up menu (Quick Launcher).
Bluetooth Stack for This software enables communication between
Windows by Toshiba remote Bluetooth devices.
Bluetooth cannot be used in models that do not have a Bluetooth module

installed.
TOSHIBA SD The TOSHIBA SD memory boot utility allows you

Memory Boot Utility to create a bootable SD memory card to start the
system. You can launch the TOSHIBA SD
Memory Boot Utility from the menu bar by
clicking start, point to All Programs, point to
TOSHIBA, point to Utilities and click SD
Memory Boot Utility.
TOSHIBA Zooming This utility allows you to enlarge or reduce the
Utility icon size on the desktop or the application
window.
RecordNow! Basic You can create CD/DVDs in several formats
for TOSHIBA including audio CDs that can be played on a
standard stereo CD player and data CD/DVDs to
store the files and folders on your hard disk drive.
This software can be used on a model with
DVD-ROM and CD-R/RW drive and DVD Super
Multi drive.
TOSHIBA Assist TOSHIBA Assist is a graphical user interface that
provides easy access to help and services.

Introduction
TOSHIBA PC TOSHIBA PC Diagnostic Tool displays the basic

Diagnostic Tool information on the computer's configuration and
allows some of the built-in devices functionality to
be tested. To start TOSHIBA PC Diagnostic Tool,
click start, point to All Programs, point to
TOSHIBA, point to Utility and click PC
Diagnostic Tool.
Sound drivers A broad range of audio controls are available
through the ADI sound driver, including Software
Synthesize, Mic Volume, Noise Reduction and
Audio Power Management.
Click start, click Control Panel and click
SoundMAX icon to change the Mic Noise
Reduction settings and the Power Management
settings. If you are viewing the Control Panel in
Category View, click on Switch to Classic View.
For other sound settings, use the Windows
Device Manager, Multimedia Panel or Volume
Dial.
TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to
allow easy control of communication devices and
network connections. TOSHIBA ConfigFree also
allows you to find communication problems and
create profiles for easy switching between
locations and communication networks. To start
ConfigFree, click start, point to All Programs,
point to TOSHIBA, point to Networking and click
ConfigFree.
TOSHIBA Password This utility lets you set a password that restricts
Utility access to the computer.
TOSHIBA This utility lets you make the Fn key sticky, that
Accessibility is, you can press it once, release it, and they
press an “F number” key. The Fn key remains
active until another key is pressed.
DLA for TOSHIBA DLA (Drive Letter Access) is the packet writing
software which provides the function to write files
and/or folders to DVD-RW, CD-RW and
DVD+RW media via a drive letter like a floppy
disk or other removable disk device.
TOSHIBA Hotkey This utility allows you to change the active
Utility for Display display device together with the display
Devices resolution. Press Fn + F5 to change the active
display device and press Fn + Space keys to
change the display resolution.

Introduction
TOSHIBA SD This utility allows you to format SD memory cards

Memory Card Format to the SD standard.
TOSHIBA Acoustic This utility allows you to configure the read speed
Silencer of CD/DVD drive. You can either configure
Normal Mode, which operates the drive at its
maximum speed for quick data access, or Quiet
Mode which runs at single speed for CD audio or
DVD video playback, and which can lessen
operational noise.
Options
You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:
Memory expansion A 256, 512 or 1,024 MB memory module

(DDR 333) can easily be installed in the
computer.
Battery pack An additional battery pack can be purchased
from your TOSHIBA dealer. Use it as a spare or
replacement.
AC adaptor If you use your computer at more than one site
frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.
USB floppy disk Kit USB floppy disk drive accommodates
1.44-megabyte or 720-kilobyte floppy disk. It
connects to a USB port. (You cannot format
720-kilobyte floppy disks on Windows XP,
but you can use previously formatted disks.)
libretto DVD Dock A libretto DVD Dock accommodates either the
DVD-ROM and CD-R/RW drive or the DVD
Super Multi drive. It connects to a docking
interface of the computer's underside.
Bluetooth SD card3 The Bluetooth SD Card 3 is an optional
accessory that is compatible with the SD card
slot of this computer. You can buy this card from
your TOSHIBA dealer.
Bluetooth USB The Bluetooth USB adaptor is an optional
adaptor accessory that is compatible with the USB ports
of this computer.
You can buy this device from your TOSHIBA
dealer.

Introduction
Mobile HDD A mobile external hard disk drive can be

purchased that is compatible with USB 2.0
standard. Data can be read and written to this
device by connecting it to the USB port of the
computer.
You can buy this device from your TOSHIBA
dealer.
DVD-ROM and CD-R/ DVD-ROM and CD-R/RW drive is available as an
RW drive optional external optical disk drive.
You can buy the drive from TOSHIBA dealer.

libretto U100
Chapter 2
The Grand Tour
This chapter identifies the various components of your computer.

Become familiar with each component before you operate the computer.*5
Disclaimer (Non-applicatable Icons)

Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.
Front with the display closed

Figure 2-1 shows the computer’s front with its LCD display panel in the
closed position.
PC card eject lever System indicators
SD card slot i.LINK (IEEE 1394) port
Figure 2-1 Front of the computer with LCD display panel closed
SD card slot SD cards are used in a wide variety of external

devices. This slot lets you transfer data from the
device to your computer.
User’s Manual 2-1

The Grand Tour
Keep foreign objects out of the SD card slot. Never allow metal objects,
such as screws, staples and paper clips, to enter the PC or keyboard.
Foreign metal objects can create a short circuit, which can cause PC
damage and fire, possibly resulting in serious injury.
PC card eject lever This is a lever for removing the PC card from
within the PC card slot.
i.LINK (IEEE1394) This port allows you to connect an external

port device, such as a digital video camera for
high-speed data transfer.
System LEDs let you monitor the status of various
indicators computer functions. Details are given in the
System indicators section.
Left side
Figure 2-2 shows the computer’s left side.
Wireless communication switch Mini-RGB port
DC IN 15V jack Cooling vents PC card slot
Figure 2-2 The left side of the computer
DC IN 15V jack The AC adaptor connects to this jack. Use only

the model of AC adaptor that comes with the
computer. Using the wrong adaptor can damage
your computer.
Cooling vents Cooling vents help CPU keep from overheating.
Do not block the cooling vents. Never allow metal objects, such as screws,
staples and paper clips, to enter the PC or keyboard. Foreign metal objects
can create a short circuit, which can cause PC damage and fire, possibly
resulting in serious injury.
2-2 User’s Manual

The Grand Tour
Wireless Slide this switch to the left to turn on Wireless

communication LAN and Bluetooth functions. Slide it to the right
switch to turn off the functions.
All models are provided with a Wireless
Communication switch although only some
models are equipped with both Wireless LAN
and Bluetooth functions.
■ Turn WiFi and Bluetooth functionalities off when near a person who
may have a cardiac pacemaker implant or other medical electric
device. Radio waves may affect pacemaker or medical device
operation, possibly resulting in serious injury. Follow the instruction of
your medical device when using any WiFi or Bluetooth functionality.
■ Always turn off WiFi or Bluetooth functionality if the PC is near
automatic control equipment or appliances such as automatic doors or
fire detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.
■ Do not use the WiFi or Bluetooth functionalities near a microwave oven
or in areas subject to radio interference or magnetic fields. Interference
from a microwave oven or other source can disrupt WiFi or Bluetooth
operation.
Mini-RGB port This Mini-RGB port lets you connect an external

video display.
PC card slot The PC card slot can accommodate a Type II

card. The slot supports 16-bit PC cards and
CardBus PC cards.
Keep foreign objects out of the PC card slot. Never allow metal objects,
User’s Manual 2-3

The Grand Tour
Right side
Figure 2-3 shows the computer’s right side.
USB ports LAN jack
Headphone jack
Volume control Microphone jack Modem jack
Figure 2-3 The right side of the computer
Volume control Use this dial to adjust the volume of the stereo
speakers and the stereo headphones.
Headphone jack A 3.5 mm mini headphone jack enables
connection of stereo headphones.
Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.
Universal Serial Bus Two Universal Serial Bus ports are on the right
(USB 2.0) port side. The ports comply with the USB 2.0
standard, which enables data transfer speeds
40 times faster than the USB 1.1 standard
(The ports also support USB 1.1).
Keep foreign objects out of the USB connectors. Never allow metal
objects, such as screws, staples and paper clips, to enter the PC or
keyboard. Foreign metal objects can create a short circuit, which can
cause PC damage and fire, possibly resulting in serious injury.
Operation of all functions of all USB devices has not been confirmed.
Some functions might not execute properly.
Modem jack In areas where an internal modem is installed as

standard equipment, there is a modem jack that
lets you use a modular cable to connect the
modem directly to a telephone line.
2-4 User’s Manual

The Grand Tour
■ Connection to any communication line other than an analog phone line

could cause a PC system failure.
■ Connect the built-in modem only to ordinary analog phone lines.
■ Never connect the built-in modem to a digital line (ISDN).
■ Never connect the built-in modem to the digital connector on a
public telephone or to a digital private branch exchange (PBX).
■ Never connect the built-in modem to a key telephone system for
residences or offices.
■ Never operate your PC on AC power during a thunderstorm. If you see
lightning or hear thunder, immediately turn off the PC. An electric surge
caused by the storm, may result in a system failure, loss of data or
hardware damage.
LAN jack This jack lets you connect to a LAN. The

adaptor has built-in support for Ethernet LAN
(10 megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second,
100BASE-TX). Refer to Chapter 4, Operating
Basics, for details.
■ Do not connect any cable other than a LAN cable to the LAN jack.
It could cause damage or malfunction.
■ Do not connect the LAN cable to a power supply. It could cause
damage or malfunction.
Back side
Figure 2-4 shows the computer’s back side.
Battery pack
Figure 2-4 The back side of the computer
Battery pack The battery pack powers the computer when

the AC adaptor is not connected. For detailed
information on the battery pack, refer to
Chapter 6, Power and Power-Up Modes.
User’s Manual 2-5

The Grand Tour
Underside
Figure 2-5 shows the underside of the computer. Make sure the display is
closed before turning over your computer.
Notches
Battery lock
Battery
release latch
Docking
port
Memory module cover
Figure 2-5 The underside of the computer
Battery lock Slide this latch in order to unlock the battery pack
ready for removal.
Battery release Slide and hold this latch to release the battery
latch pack for removal.
For detailed information on removing the battery
pack, refer to Chapter 6, Power and Power-Up
Modes.
Docking port This port enables connection of an optional
docking unit to access additional devices
including an optical media drive, refer to Chapter
8, Optional Devices.
Keep foreign objects out of the docking interface port. Never allow metal
objects, such as screws, staples and paper clips, to enter the PC or
keyboard. Foreign metal objects can create a short circuit, which can
cause PC damage and fire, possibly resulting in serious injury. A plastic
shutter protects the connector.
2-6 User’s Manual

The Grand Tour
Notches Notches on the computer engage hooks on the

libretto docking device to ensure a secure
connection.
Memory module This cover protects one memory module socket.
cover Depending on the configuration of the computer
either one or no module is preinstalled. Refer to
the Memory expansion section in Chapter 8,
Optional Devices.
Front with the display open

This section shows the front of the computer with the LCD display panel
open. Refer to the appropriate illustration for details. To open the LCD
display panel, simply lift it up at its front edge. Position the LCD display
panel at a comfortable viewing angle.
Display hinge
LCD screen
Stereo speaker (Right)
AccuPoint
Stereo speaker
(Left)
LCD Sensor switch

(Not shown)
Fingerprint
Sensor
Power button
AccuPoint control buttons
Figure 2-6 The front of the computer with the LCD panel open
User’s Manual 2-7

The Grand Tour
Display hinge The display hinge holds the LCD display panel at
easy-to-view angles.
LCD screen The LCD screen displays high-contrast text and
graphics. The computer’s WXGA screen consists
of 1280 × 768 pixels. Refer to Display Controller
and Modes in Appendix B.
When the computer operates on the AC adaptor
the LCD screen’s image will be somewhat
brighter than when it operates on battery power.
The lower brightness level is intended to save
battery power.
LCD Sensor switch This switch senses when the computer’s LCD
display panel is closed or opened and activates
the Panel Power Off/On feature. When you close
the LCD display panel the computer enters
Hibernation mode and shuts down. When you
open the computer’s LCD display panel the
computer starts in Hibernation mode. Use the
TOSHIBA Power Saver Utility to enable or
disable this feature. The default is “enabled”.
Refer to the TOSHIBA Power Saver Utility and
Panel Power Off/On items in Chapter 1, Special
features, for details on settings.
Do not put a magnetic object close to the switch. The computer will
automatically enter Hibernation mode and shut down even if the Panel
Power Off features is disabled.
Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.
AccuPoint A pointer control device located in the center of
the palm rest is used to control the on-screen
pointer. Refer to the Using the AccuPoint section
in Chapter 4, Operating Basics.
AccuPoint control Control buttons below the keyboard let you select
buttons menu items or manipulate text and graphics
designated by the on-screen pointer. Refer to the
Using the AccuPoint section in Chapter 4,
Operating Basics.
2-8 User’s Manual

The Grand Tour
Fingerprint Sensor Just by swiping the finger against the fingerprint

sensor, the following functions will be enabled:
■ Logon to Windows and access a
security-enabled homepage through IE
(Internet Explorer).
■ Files and folders can be encrypted/decrypted
and third party access to them prevented.
■ Disable the password-protected screen-saver
when returning from power-saving (standby)
mode.
Power button Press the power button to turn the computer’s
power on and off.
System indicators
LEDs beneath icons, light when various computer operations are in
progress.
DC IN Power Battery HDD Wireless

Communication
Figure 2-7 System indicators
DC IN The DC IN indicator glows in green when DC

power is supplied from the AC power adaptor.
If the adaptor’s output voltage is abnormal or if
the power supply malfunctions, this indicator
flashes orange.
Power The Power indicator glows in green when the
computer is on. If you select Standby from Shut
Down Windows, this indicator flash orange
(one second on, two seconds off) while the
computer shuts down.
Battery The Battery indicator shows the condition of the
battery’s charge: Green indicates full charge,
orange indicates battery charging and flashing
orange indicates a low battery charge. Refer to
Chapter 6, Power and Power-Up Modes.
HDD The HDD indicator glows green when the
computer is accessing the built-in hard disk.
User’s Manual 2-9

The Grand Tour
Wireless The Wireless communication indicator glows

communication when the Wireless LAN and Bluetooth functions
are turned on.
Some models are equipped with wireless
communication functionality.
USB floppy disk drive

The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte
floppy disks and connects to the USB port. It is supplied as standard with
some models and as an option with others.
USB connector
Disk-In-Use Indicator Floppy disk slot Eject button

Figure 2-8 USB floppy disk drive
USB connector Insert this connector to the USB port of your

computer.
Disk-In-Use Indicator This indicator lights when the floppy disk is being
accessed.
Floppy disk slot Insert a floppy disk in this slot.
Eject button When a floppy disk is fully seated in the drive,
the eject button pops out. To remove a floppy
disk, push in the eject button and the floppy disk
pops out partially for removal.
Check the Disk-In-Use indicator when you use the USB floppy disk drive.
Do not press the eject button or turn off the computer while the light is
glowing. Doing so could destroy data and damage the floppy disk or the
drive.
■ The USB floppy disk drive should be placed on a flat, horizontal surface
when in use. Do not set the drive on an incline greater than 20° while it
is operating.
■ Do not set anything on top of the floppy disk drive.

The Grand Tour
Optical media drives

■ The optical media drive can be used by connecting the libretto DVD
Dock to this computer.
One of the following optical media drives is installed in the computer:

DVD-ROM and CD-R/RW and DVD Super Multi drives. An ATAPI interface
controller is used for CD/DVD-ROM operation. When the computer is
accessing a CD/DVD, an indicator on the drive glows.
For information on loading and unloading discs refer to the Using optical
media drives section in Chapter 4, Operating Basics.
Region codes for DVD drives and media

DVD-ROM and CD-R/RW and DVD Super Multi drives and media are
manufactured according to the specifications of six marketing regions.
When you purchase DVD-Video, make sure it matches your drive,
otherwise it will not play properly.
Code Region
1 Canada, United States
2 Japan, Europe, South Africa, Middle East
3 Southeast Asia, East Asia
4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean
5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6 China

The Grand Tour
Writable discs
This section describes the types of writable CD/DVD discs. Check the
specifications for your drive to for the type of discs it can write. Use
RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.
CDs
■ CD-R discs can be written only once. The recorded data cannot be
erased or changed.
■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW
discs, and ultra-speed CD-RW discs can be recorded more than once.
DVDs
■ DVD-R and DVD+R discs can be written only once. The recorded data
cannot be erased or changed.
■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than
once.
Formats
The drives support the following formats:
■ CD-ROM ■ DVD -Video
■ DVD-ROM ■ CD-Text
■ CD-DA ■ CD-ROM Mode 1, Mode 2
■ Photo CDTM (single/multi-session) ■ Enhanced CD (CD-EXTRA)
■ CD-ROM XA Mode 2 (Form1, ■ Addressing Method 2
Form2)
DVD-ROM and CD-R/RW drive

The full-size DVD-ROM and CD-R/RW drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.
The read speed is slower at the center of a disc and faster at the outer
edge.
DVD read 8 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, ultra-speed media)

The Grand Tour
DVD Super Multi drive

The full-size DVD Super Multi drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.The full-size DVD Super Multi drive module lets
you record data to rewritable CDs as well as run either 12 cm (4.72") or
8 cm (3.15") CD/DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the outer
edge.
DVD read 8 speed (maximum)
DVD-R write 2 speed (maximum)
DVD-RW write 2 speed (maximum)
DVD+R write 2.4 speed (maximum)
DVD+RW write 2.4 speed (maximum)
DVD-RAM write 2 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 10 speed (maximum, Ultra-speed media)
AC adaptor
The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost any country/region. The adaptor converts AC
power to DC power and reduces the voltage supplied to this computer.
To recharge the battery, simply connect the AC adaptor to a power source
and the computer. Refer to Chapter 6 Power and Power-Up Modes for
details.
Figure 2-9 The AC adaptor (2-pin plug)

The Grand Tour
Figure 2-10 The AC adaptor (3-pin plug)
■ The Universal AC Adaptor and power cord bundled with this product
may differ depending on the product model. Depending on the model,
a 2-pin plug or 3-pin plug set of the above may be bundled.
■ Do not use a 3-pin to 2-pin conversion plug.
■ The supplied power cord conforms to safety rules and regulations in
the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.
Always use the Toshiba AC adaptor that was provided with your PC and
the Toshiba Battery Charger (that may have been provided with your PC),
or use Toshiba recommended alternate models to avoid any risk of fire or
other damage to the PC. Use of an incompatible AC adaptor or Battery
Charger could cause fire or damage to the PC possibly resulting in serious
injury.

libretto U100
Chapter 3
Getting Started
This chapter provides basic information to get you started using your
computer. It covers the following topics:
■ Setting up your work space - for your health and safety
Be sure also to read Instruction Manual for Safety & Comfort. This guide,
which is included with the computer, explains product liability.
■ Connecting the AC adaptor
■ Opening the display
■ Turning on the power
■ Starting up for the first time
■ Turning off the power
■ Restarting the computer
■ Restoring your preinstalled software
All users should be sure to read the section Starting up for the first time.
Setting up your work space

Establishing a comfortable work site is important for you and your
computer. A poor work environment or stressful work habits can result in
discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. Proper ambient conditions should also be maintained for the
computer’s operation. This section discusses the following topics:
■ General conditions
■ Placement of the computer
■ Seating and posture
■ Lighting
■ Work habits
User’s Manual 3-1

Getting Started
General conditions
In general, if you are comfortable, so is your computer, but read the
following to make sure your work site provides a proper environment.
■ Select a work area that has:
■ a well-designed and functioning ventilation system that does not
forcefully direct air on you
■ good air circulation
■ a comfortable ambient temperature and relative humidity.
■ Never place your PC where it will be exposed to excess heat, such as in
direct sunlight, an unventilated vehicle or near a heater. This may result
in a system failure, malfunction, loss of data or damage to PC.
■ Never place your PC in a location where it will be exposed to extremely
low temperatures. This may result in a system failure, malfunction or
loss of data.
■ Never subject your PC to sudden temperature variations. This may
result in condensation, causing a system failure, malfunction or loss of
data.
■ Do not expose your PC to dusty environments. If dust gets inside the
PC, it could cause a system failure, malfunction or loss of data. If dust
contaminates the PC, do not turn on the power. Take it to an authorized
Toshiba service provider before you use it.
■ Never place your PC near an object that generates a magnetic field,
such as a speaker or TV. Do not wear magnetic bracelets while using
your PC. Exposure to magnetic fields can cause system failure,
malfunction or loss of data.
■ Never place a heavy object on the PC and be careful not to drop a
heavy object onto the PC. It could damage the PC or cause system
failure.
■ Never use benzene, thinner or other chemicals when cleaning the PC,
AC adaptor, or storage device. The use of benzene, thinner or other
chemicals may result in deterioration, deformation or discoloration of
those items and the loss of data.
■ Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
■ The temperature should be 5 to 35 degrees Centigrade
(41 to 95 degrees Fahrenheit) and the relative humidity should be
20 to 80 percent.
■ Keep the computer free of dust, moisture, and exposure to direct
sunlight.
■ Some parts of the computer, including data storage media, can be
damaged by magnets. Do not place the computer near magnetic
objects or bring magnetic objects close to the computer. Be careful of
objects, such as stereo speakers, that produce strong magnetic fields
during operation. Also, be careful with metal objects, such as bracelets,
which can be inadvertently magnetized.
■ Do not operate the computer in close proximity to a mobile phone.
3-2 User’s Manual

Getting Started
■ Leave ample ventilation room for the fan. Do not block the vents.
■ If the PC interferes with radio equipment, turn the PC power off
immediately. Such interference could cause equipment malfunction.
■ Never place your PC on a shaky table, uneven, tilted surface or other
unstable location. Your PC may fall, causing damage to the PC or
possibly injury.
■ Never leave the power to your PC on continuously for more than
24 hours. Turn the power off when this product is not in use.
■ Always avoid abrupt changes of temperature or humidity.
■ Never place close to heat radiating appliances such as a heater.
■ Never place close to corrosive chemicals.
■ Never place close to magnetic field radiating appliances such as a
stereo speaker.
■ Always place this product on a flat surface.
■ Provide a sufficient space behind the PC to allow easy adjustment of
the display panel.
■ Always provide sufficient space around the PC to ensure adequate
ventilation.
■ Always provide sufficient space for operating a mouse and other
peripheral devices.
Placement of the computer

Position the computer and peripheral devices to provide comfort and safety.
■ Position your LCD display panel or place your monitor in an appropriate
position to help reduce awkward postures and overhead glare. For
example:
■ Position LCD directly in front of you and at a comfortable distance
away.
■ Position LCD so the top of the screen is at or slightly below eye
level. A display screen that is too high or too low can cause
awkward postures and possibly fatigue muscles that support the
head.
■ Rest your eyes periodically by focusing on objects that are farther
away.
■ If you use a paper holder, set it at about the same height and distance
as the computer.
User’s Manual 3-3

Getting Started
Seating and posture

Maintain a comfortable working posture when using your PC where your
body joints are naturally aligned to reduce stress on different parts of your
body. Consider the following:
Below eye level
90°angles
Foot rest
Figure 3-1 Posture and positioning of the computer
■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to
the floor.
■ Keep head level, or bent slightly forward, forward facing, and balanced.
Generally the head is in-line with the torso.
■ Keep shoulders relaxed and let upper arms hang normally at the side of
the body.
■ Keep elbows in close to the body and bent.
■ Keep feet fully supported by floor or foot rest.
■ Keep back fully supported with appropriate lumbar support when sitting
vertical or leaning back slightly.
■ Keep thighs and hips supported by a well-padded seat cushion and
generally parallel to the floor.
■ Keep knees about the same height as the hips with the feet slightly
forward.
3-4 User’s Manual

Getting Started
Lighting
Select the right level of illumination and place your PC appropriately to
minimize glare from overhead lights, desk lamps and windows. Glare on
the LCD or monitor may cause eye strain, eye fatigue or headaches.
Consider the following suggestions regarding lighting your work
environment:
■ Position the PC so that the light source does not shine or reflect directly
onto the display or shine or reflect directly into the eyes of the user.
■ Shield the PC from direct light by using tinted windows or by installing
blinds or a screen.
■ Use soft, indirect lighting.
■ Adjust the display panel to provide maximum visibility.
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your
activities. If possible, schedule a variety of tasks into your workday. If you
must spend long periods at the computer, finding ways to break up the
routine can reduce stress and improve your efficiency.
■ Sit in a relaxed posture. Good positioning of your chair and equipment
as described earlier can reduce tension in your shoulders or neck and
ease back strain.
■ Vary your posture frequently.
■ Occasionally stand up and stretch or exercise briefly.
■ Exercise and stretch your wrists and hands a number of times during
the day.
■ Frequently, look away from the computer and focus your eyes on a
distant object for several seconds, for example 30 seconds every
15 minutes.
■ Take frequent short breaks instead of one or two long breaks,
for example, two or three minutes every half hour.
■ When you use a PC, rest your eyes periodically and relax or stretch
your muscles to avoid strain. If you experience discomfort while
operating the PC, stop immediately and rest. Continuous operation for
long periods without adequate rest may cause pain in the arms, wrists,
hands, back, neck or other parts of the body. If pain persists despite
rest, consult your doctor.
A number of books are available on ergonomics and repetitive strain injury
or repetitive stress syndrome. For more information on these topics or for
pointers on exercises for such stress points as hands and wrists, please
check with your library or book vendor. Also refer to the computer’s
Instruction Manual for Safety & Comfort.
User’s Manual 3-5

Getting Started
Strategic Rest Breaks

Take short, strategically spaced rest breaks to avoid eye strain and body
discomforts.
For more specific recommendations on the safety and comfort of your
computer environment, customers in the United States may visit the United
States Department of Labor, Occupational Safety & Health Administration
website at: http://www.osha.gov/SLTC/etools/computerworkstations/
Other Things to Note

■ Never turn off the power while an application is running. Doing so could
cause loss of data.
■ Use a virus-check program and make sure it is updated regularly.
■ Never turn off the power, disconnect an external storage device or
remove storage media during data read/write. Doing so can cause data
loss.
■ Never format storage media without checking its content. Formatting
destroys all stored data.
■ It is a good idea to periodically back up the internal hard disk or other
main storage device to external media. General storage media is not
durable or stable over long periods of time and under certain conditions
may result in data loss.
■ Before you install a device or application, save any data in memory to
the hard disk drive or other storage media. Failure to do so may result in
the loss of data.
3-6 User’s Manual

Getting Started
Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.
The AC adaptor can be connected to any power source supplying from
100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
■ Always use the Toshiba AC adaptor that was provided with your PC
and the Toshiba Battery Charger (that may have been provided with
your PC), or use Toshiba recommended alternate models to avoid any
risk of fire or other damage to the PC. Use of an incompatible AC
adaptor or Battery Charger could cause fire or damage to the PC
■ Use only the AC adaptor supplied with your computer or an equivalent
adaptor that is compatible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no liability for any damage
caused by use of an incompatible adaptor.
■ Never plug the AC adaptor or Battery Charger into a power source that
does not correspond to both the voltage and the frequency specified on
the regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.
■ Always use or purchase power cables that comply with the legal
voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.
■ Do not use a 3-pin to 2-pin conversion plug.
■ When you connect the AC adaptor to the computer, always follow the
steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical change
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.
■ Never place an AC adaptor on a wooden surface, furniture, or any
other surface that could be marred by exposure to heat since the AC
adaptor's surface temperature increases during normal use.
■ Always place the PC on a suitable heat-insulating material to prevent
possible heat damage.
User’s Manual 3-7

Getting Started
1. Connect the power cord to the AC adaptor.
Figure 3-2 Connecting the power cord to the AC adaptor (2-pin plug)
Figure 3-3 Connecting the power cord to the AC adaptor (3-pin plug)
The Universal AC Adaptor and power cord bundled with this product may
differ depending on the product model. Depending on the model, a 2-pin
plug or 3-pin plug set of the above may be bundled.
2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the
back of the computer.
DC IN 15V jack
Figure 3-4 Connecting the adaptor to the computer
3. Plug the power cord into a live wall outlet. The Battery and DC IN
indicators on the front of the computer should glow.
3-8 User’s Manual

Getting Started
Opening the display

The computer’s LCD display panel can be rotated in a wide range of angles
for optimal viewing.
1. While holding down the palm rest with one hand so that the main body
is not raised, lift the panel slowly. Adjust the angle of the panel to
provide optimal clarity.
As the display panel cannot be opened beyond 180 degrees, please be
careful when flipping open the display panel.
Use reasonable care when opening and closing the LCD display panel.
Opening it vigorously or slamming it shut could damage the computer.
LCD display panel
Figure 3-5 Opening the LCD display panel
User’s Manual 3-9

Getting Started
Turning on the power

This section describes how to turn on the power.
The Power button LED indicates the status. Refer to the Power indicator
section in Chapter 6, Power and Power-Up Modes.
■ After you turn on the power for the first time, do not turn it off until you
have set up the operating system. Refer to the section Starting up for
the first time.
■ If the USB floppy disk drive is connected, make sure it is empty.
If a floppy disk is in the drive, press the eject button and remove the
floppy disk.
1. Open the computer’s LCD display panel.
2. Press and hold the computer’s power button for two or three seconds.
Power button
Figure 3-6 Turning on the power
Do not push the power button strongly.
Starting up for the first time

When you first turn on the power, the computer’s initial screen is the
Microsoft Windows XP Startup Screen Logo. Follow the on-screen
directions for each screen. During setup, you can click the Back button to
return to the previous screen.
Be sure to read the Windows End User License Agreement display
carefully.
Be sure to read the License Agreement carefully.

Getting Started
Turning off the power

The power can be turned off in one of the following modes: Shut down
(Boot), Hibernation or Standby mode.
Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk or to a floppy disk.
2. Make sure all disk (disc) activity has stopped, then remove the
CD/DVDs or floppy disk.
■ Make sure the HDD indicator is off. If you turn off the power while a
disk (disc) is being accessed, you can lose data or damage the disk
(disc).
■ Never turn off the power while an application is running. Doing so could
cause loss of data.
3. Click start then click Turn Off Computer. From the Turn Off
Computer menu select Turn Off.
4. Turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk
when the computer is turned off. The next time the computer is turned on,
the previous state is restored. The hibernation feature does not save the
status of peripheral devices.
■ Save your data. While entering hibernation mode, the computer saves
the contents of memory to the hard disk drive although, for safety sake,
it is best to save your data manually.
■ Data will be lost if you remove the battery or disconnect the AC adaptor
before the save is completed. Wait for the HDD indicator to go out.
■ Do not install or remove a memory module while the computer is in
hibernation mode. Data will be lost.

Getting Started
Benefits of hibernation
The hibernation feature provides the following benefits:
■ Saves data to the hard disk when the computer automatically shuts
down because of a low battery.
For the computer to shut down in hibernation mode, the hibernation feature
must be enabled in two places: the Hibernate tab in Power Options and
Otherwise, the computer will shut down in Standby mode. If battery power
becomes depleted, data saved in Standby mode will be lost.
■ You can return to your previous working environment immediately when

you turn on the computer.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System
hibernate feature.
■ You can use the panel power off feature.
Starting Hibernation
You can also enable Hibernation by pressing Fn + F4. Refer to Chapter 5,

The Keyboard, for details.
To enter Hibernation mode, follow the steps below.

1. Click start.
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Click Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.
1. Click start and open the Control Panel.
2. Open Performance and Maintenance and open Power Options.
3. Select the Hibernate window in the Power Options Properties,
select the Enable hibernation check box and click the Apply button.
4. Open TOSHIBA Power Saver.
5. Select the Setup Action window.
6. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.
7. Click the OK button.

Getting Started
Data save in hibernation mode

When you turn off the power in hibernation mode, the computer takes a
moment to save current memory data to the hard disk. During this time,
the HDD indicator will light.
After you turn off the computer, and the content of memory has been saved
to the hard disk, turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
Standby mode
If you have to interrupt your work, you can turn off the power without exiting
from your software. Data is maintained in the computer’s main memory.
When you turn on the power again, you can continue working right where
you left off.
■ When the AC adaptor is connected, the computer will go into Standby
mode according to the settings in the TOSHIBA Power Saver utility.
■ To restore operation from Standby mode, press the power button or
press any key. The latter action works only if Wake-up on Keyboard is
enabled in HW Setup.
■ If the computer automatically enters Standby mode while a network
application is active, the application might not be restored when the
computer wakes up from Standby.
■ To prevent the computer from automatically entering Standby mode,
disable Standby in TOSHIBA Power Saver. That action, however,
will nullify the computer’s Energy Star compliance.
■ Before entering Standby mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in
standby mode. The computer or the module could be damaged.
■ Do not remove the battery pack while the computer is in standby mode
(unless the computer is connected to an AC power source). Data in
memory will be lost.
■ If you carry the computer on board an aircraft or into a hospital, be sure
to shut down the computer in hibernation mode or in shutdown mode to
avoid radio signal interference.
Benefits of standby
The standby feature provides the following benefits:
■ Restores the previous working environment more rapidly than does
hibernation.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System Standby
feature.
■ You can use the panel power off feature.

Getting Started
Executing standby
You can also enable Standby by pressing Fn + F3. See Chapter 5, The
Keyboard, for details.
You can enter standby mode in one of three ways:
1. Click start, click Turn Off Computer and click Stand By.
2. Close the computer’s LCD display panel. This feature must be enabled.
Refer to the Setup Action tab in TOSHIBA Power Saver Utility
described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
3. Press the power button. This feature must be enabled. Refer to the
Setup Action tab in TOSHIBA Power Saver Utility described in the
Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
When you turn the power back on, you can continue where you left when
you shut down the computer.
■ When the computer is shut down in standby mode, the power indicator
will flash orange.
■ If you are operating the computer on battery power, you can lengthen
the operating time by shutting down in hibernation mode. Standby
mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
■ Power is turned back on immediately after shutting down.
■ Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer

Certain conditions require that you reset the system. For example, if:
■ You change certain computer settings.
■ An error occurs and the computer does not respond to your keyboard
commands.
■ There are three ways to reset the computer system:
1. Click start then click Turn off computer. From the Turn off
computer menu select Restart.
2. Press Ctrl + Alt + Del to display the Windows Task Manager, then
select Shut Down and Restart.
3. Press the power button and hold it down for five seconds.
Wait 10 to 15 seconds, then turn the power on again by pressing the
power button.

Getting Started
Restoring your preinstalled software
If preinstalled files are damaged, use the supplied backup media to restore
them. To restore the operating system and all preinstalled software, follow
the steps below.
Where available, the optional libretto DVD Dock is needed to use the
DVD-ROM and CD-R/RW drive or DVD Super Multi drive - this item can be
purchased from TOSHIBA dealers. In addition the computer also supports
the following TOSHIBA optical disc drives for product recovery:
External CD-RW/DVD-ROM Drive PA3352A, PA3352C, PA3352L
External DVD Super-Multi Drive PA3402C, PA3402A, PA3402L
Slim Combo CD-R/RW and DVD-ROM PA3438U
Please use the Express Media Player Recovery CD first to reinstall the
“Express Media Player” before you reinstall a Windows® operating system.
Restoring the complete system

If pre-installed files are damaged, use the Express Media Player Recovery
CD and the Product Recovery disc to restore them.
Some models do not have Express Media Player pre-installed, therefore
the Express Media Player Recovery CD is not available.
In these instances please refer to the procedure in “Restoring the
operating system” as described below.
Restoring the Express Media Player

To restore the Express Media Player , follow the steps below.
1. Load the Express Media Player Recovery CD in the optical media drive
and turn off the computer’s power.
2. Hold down the F12 key and turn on the power. When the boot menu
appears, release the F12 key.
3. Use the cursor keys to select the CD/DVD drive in the Boot menu.
4. Follow the on-screen instructions and select ‘Overwrite Installation’
using the cursor keys to restore the Express Media Player.
When you are using “Delete all partitions” the hard disk will be reformatted
and all data will be lost.

Getting Started
Restoring the operating system

To restore the operating system and all pre-installed software, follow the
steps below.
When you reinstall the Windows® operating system, the hard disk will be
reformatted and all data will be lost.
1. Load the Product Recovery disc in the drive and turn off the computer's
power.
2. Hold down the F12 key and turn on the power. When the boot menu
appears, release the F12 key.
3. Use the cursor keys to select the CD-ROM/DVD drive in the Boot
menu.
4. Follow the on-screen instructions.
5. If your computer came with additional software installed, this software
can not be recovered from the Product Recovery disk. Re-install these
applications (e.g. Works Suite, DVD Player, Games, etc.) separately
from other media.
Restoring TOSHIBA utilities and drivers

If Windows is working properly, individual drivers or applications can be
separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD)
contains drivers and applications, which are included with your computer
system. If your system drivers or applications have become damaged in
some way, you can reinstall most of the components from this folder.
Create a copy of this folder to an external media for more convenience.

Getting Started
Restoring the preinstalled software from the hard disk
Create Optical Recovery Discs

This feature is only available for models which are configured for hard disk
recovery. For these models Product Recovery media is not supplied with
the computer.
■ The optional libretto DVD Dock is needed to use the DVD-ROM and
CD-R/RW drive or DVD Super Multi drive.
■ A writable external optical media drive that is sold separately and is
compatible with the computer is required to create the Recovery Discs.
These drives can be purchased from TOSHIBA dealers.
■ This computer supports the following optical disc drives for the
creation of recovery discs:
■ Be sure to connect the AC adaptor when you create Recovery Discs.
■ Be sure to close all other software programs except the Recovery Disc
Creator.
■ Do not run software such as screen savers which can put a heavy load
on the CPU.
■ Operate the computer at full power.
■ Do not use power-saving features.
■ Do not write to the disc when the virus check software is running. Wait
for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.
■ Do not use hard disk utilities, including those intended to enhance the
hard disk drive's access speed. They may cause unstable operation
and damage data.
■ Do not shut down/log off or standby/hibernate while writing or rewriting
the disc.
■ Set the computer on a level surface and avoid places subjected to
vibrations such as airplanes, trains, or cars.
■ Do not use on an unstable surface such as a stand.

Getting Started
A recovery image of your computer is stored on the hard disk. You may use
this image to create CD or DVD recovery discs using the following steps:
1. Select either blank CD or DVD media.
2. The application will allow you to choose from a variety of media when
creating the recovery discs including: CD-R, CD-RW, DVD-R, DVD-RW,
DVD+R and DVD+RW.
Some media may not be compatible with the Optical Drive of your
computer. Please ensure that the Optical Drive supports the blank media
you choose.
3. Turn on your computer to open Windows XP.

RecordNow! Basic for TOSHIBA is required to create the Recovery Discs.
Other disc writing software is not supported.
4. Insert the first blank media into the tray of the optical drive.
5. Double click the Recovery Disc Creator Launcher icon on the Windows
XP desktop, or select the application from the start Menu.
6. After Recovery Disc Creator starts, select the type of media and the title
you wish to copy to the media then click the Burn button.
■ If your Optical Drive can only write to CDs, select “CD” as the “Type”
within the Recovery Disc Creator. If your Optical Drive of your
computer can write to either CD or DVDs, select the one you are using
as the “Type” within the Recovery Disc Creator.
■ You can also create the recovery CD for the Express Media Player
using the Recovery Disc Creator.
Restoring the preinstalled software from the recovery hard

disk drive
the computer.
About 2GB of hard disk space is reserved for the recovery partition.
When re-setting up your hard disk, do not change, delete or add partitions
in a manner other than specified in the manual. Otherwise, space for
software may be destroyed.
In addition, if you use a third-party partitioning program to reconfigure
partitions on your hard disk, it may become impossible to re-setup your
computer.
1. Turn off your computer.
2. While holding down 0 (zero) key on the keyboard, turn on your
computer.

Getting Started
3. A menu appears. Press the “1” key on the keyboard to restore the
original configuration as purchased. Press the “2” key to keep your
current partitions intact and restore. Press the “3” key to specify
partitions and restore.
Restoring the preinstalled software from your created

Recovery Media
the computer.
■ The optional libretto DVD Dock is needed to use the DVD-ROM and
CD-R/RW drive or DVD Super Multi drive.
■ An external optical media drive that is sold separately and is
compatible with the computer is required to use the Recovery Discs to
restore the preinstalled software. These drives can be purchased from
TOSHIBA dealers.
■ This computer supports the following optical disc drives for
restoring the preinstalled software:
If preinstalled files are damaged, you can either use the Recovery Media
you have created or the hard disk drive recovery to restore them. To restore
the operating system and all preinstalled software, follow the steps below.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
1. Load the Recovery Media in the optional optical media drive and turn off
the computer’s power.
2. Hold down the F12 key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the F12 key.
3. Use the left or right cursor key to select the CD-ROM icon in the display
menu. For details, refer to the Boot Priority section in Chapter 7, HW
Setup.
4. A menu appears. Press the “1” key on the keyboard to restore the hard
disk configuration, press the “2” key to restore drive C:, and press the
“3” key to restore the recovery tool.

Getting Started

libretto U100
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the

TOSHIBA Pointing Device, the USB floppy disk drive, optical media drives,
Sound System, Modem, Wireless communication features and LAN. It also
provides tips on care of the computer, floppy disks and CD/DVDs.
TOSHIBA Pointing Device

The computer is equipped with a mouse control system known as an
AccuPoint pointing stick.
AccuPoint
Fingerprint
Sensor
AccuPoint Control Buttons
Figure 4-1 AccuPoint and AccuPoint control buttons
User’s Manual 4-1

Operating Basics
Using the AccuPoint

To use the AccuPoint, simply push it with your finger tip in the direction you
want to move the on-screen pointer.
Two buttons next to the AccuPoint are used like the buttons on a mouse
pointer. Press the left button to select a menu item or to manipulate text or
graphics designated by the pointer. Press the right button to display a menu
or other function depending on the software you are using.
You can also tap the AccuPoint control buttons to perform functions similar
to those of the left button.
Click: Tap once
Double-click: Tap twice
Drag and drop: Tap to select the material you want to move. Leave
your finger on the AccuPoint control buttons after the second tap and
move the material.
If AccuPoint is tilted in a certain direction for some time and the finger is
then removed, the cursor on the screen may move in the reverse direction.
AccuPoint precautions
Certain conditions can affect the on-screen pointer when using AccuPoint.
For example, the pointer may travel contrary to AccuPoint operation or an
error message may appear, if
■ You touch the AccuPoint during power-up.
■ You apply constant, soft pressure during power-up.
■ There is a sudden temperature change.
■ Strong stress is applied to the AccuPoint.
If an error message appears, reboot the computer. If an error message
does not appear, wait a moment for the pointer to stop, then continue
operation.
4-2 User’s Manual

Operating Basics
Replacing the cap

The AccuPoint cap is an expendable item that should be replaced after
prolonged use. Depending on the model you purchased, a spare AccuPoint
cap may supplied with the computer.
1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight
up.
Figure 4-2 Removing the AccuPoint cap
2. Position a new cap on the peg and press it into place.

The peg is square, so be careful to align the cap’s square hole with the
peg.
Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling
and recognizing fingerprints. By enrolling the ID and password to the
fingerprint authentication device, it is no longer necessary to input the
password from the keyboard. Just by swiping the finger against the
fingerprint sensor, the following functions will be enabled:
■ Logon to Windows and access a security-enabled homepage through
IE (Internet Explorer).
■ Files and folders can be encrypted/decrypted and third party access to
them prevented.
■ Disable the password-protected screen-saver when returning from
power-saving (standby) mode.
To “swipe” refers to the action of reading a fingerprint using the fingerprint
sensor.
User’s Manual 4-3

Operating Basics
Points to note about the Fingerprint Sensor

Failure to follow these guidelines might result in (1) damage to the sensor
or cause sensor failure, (2) finger recognition problems, or lower finger
recognition success rate.
■ Do not scratch or poke the sensor with your nails or any hard or sharp
objects.
■ Do not press the sensor strongly.
■ Do not touch the sensor with a wet finger or any wet objects. Keep
sensor surface dry and free of water vapor.
■ Do not touch the sensor with a soiled finger. Minute foreign particles on
a soiled or dirty finger may scratch the sensor.
■ Do not paste stickers or write on the sensor.
■ Do not touch the sensor with a finger or any object with built-up static
electricity.
Observe the following before you place your finger on the sensor whether
for fingerprint enrollment/registration or recognition.
■ Wash and dry your hands thoroughly.
■ Remove static electricity from your fingers by touching any metal
surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.
■ Clean the sensor with a lint-free cloth. Do not use detergent to clean the
sensor
■ Avoid the following finger conditions for enrollment or recognition as
they may result in fingerprint enrollment errors or a drop in the
fingerprint recognition success rate
■ Soaked or swollen finger (e.g. after taking bath)
■ Injured finger
■ Wet finger
■ Soiled or oily finger
■ Extremely dry skin condition on finger
Observe the following to improve the fingerprint recognition success rate.
■ Enroll two or more fingers.
■ Enroll additional fingers if recognition failure occurs often using enrolled
fingers.
■ Check your finger condition. Changed conditions, such as injured,
rough, extremely dry, wet, soiled, dirty, oily, soaked, swollen fingers,
may lower the recognition success rate. Also if the fingerprint is worn
down or the finger becomes thinner or fatter, the recognition success
rate may be lowered.
■ The fingerprint for each finger is different and unique. Please ensure
that only the registered or enrolled fingerprint or fingerprints are used
for identification.
4-4 User’s Manual

Operating Basics
■ Check sliding position and speed (see the drawing below).

Fingerprint Sensor Limitations.
■ The fingerprint sensor compares and analyzes the unique
characteristics in a fingerprint.
■ A warning message will be displayed when recognition is abnormal or
recognition is not successful within a fixed duration.
■ The recognition success rate may differ from user to user.
■ Toshiba does not guarantee that this fingerprint recognition technology
will be error-free.
■ Toshiba does not guarantee that the fingerprint sensor will recognize
the enrolled user or accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out
of the use of this fingerprint recognition software or utility.
The following illustrations show the correct way to slide your finger over the
recognition sensor.
Align the finger and sensor like the drawings.
Points to note about the Fingerprint Utility

The user should back up the user profile information when using the
functions provided in this software to encrypt files or folders. If this software
or the user information is deleted without backing up the user profile
information, the encrypted files will no longer be accessible. In addition,
if the backup data is not used, the user will not be identified as the same
user even if the same name is used again in user enrolment.
Please refer to the following procedures to back up.
Double-click on the OmniPass icon in the task tray, select the
UserManagement tab, select Import/Export User, click on Export an
OmniPass user profile, carry out fingerprint authentication, specify the
destination folder and filename to save the profile, and save the file.
If Windows XP Professional's file encryption function EFS (Encryption File
System) is used to encrypt a file, the file cannot be further encrypted using
the encryption function of this software.
User’s Manual 4-5

Operating Basics
If the fingerprint sensor and Trusted Platform Module (TPM)security are

used as identification devices, install and configure the Infineon TPM
Professional package first before configuring the fingerprint utility. Please
refer to the TPM (Trusted Platform Module) Installation Guide for the
installation and configuration methods for TPM.
In the help file, it is stated that this software's Password Replacement
function can be used for the Internet and general applications. However,
the Internet Password Replacement function in the fingerprint utility
provided in this computer can only be used with IE (Internet Explorer).
There is a section on Strong Logon Security in the help file, but the
function is not available in the fingerprint utility provided in this computer.
The sound during Log Off Current User (when logging off from OmniPass)
cannot be set to off even if the No Audio Prompts configuration is set in
Audio Settings. If you wish to turn it off, remove the settings for wav files in
the event settings of the sound events section of the Sound and Audio
Device Property in the control panel.
Set Up Procedure
Please use the following procedure when first using fingerprint
authentication.
Fingerprint Registration
Enroll the required authentication data using the “OmniPass Enrollment
Wizard”.
The fingerprint authentication uses the same Windows logon ID and
password. If the Windows logon password has not been setup, please do
so before registration.
1. Click start, Point to All Programs, point to Softex and click OmniPass
Enrollment Wizard.
2. Click Enroll.
3. Ensure the same Windows logon username and domain (*) are
displayed before entering a password into the Password field.
Click Next.
(*) If the Windows logon account is for use within a LAN domain, enter the
domain name, otherwise, if you are unsure, please check with the network
administrator. If the logon is not used within a LAN domain, you should just
enter the computer name.
4. The Choose Finger screen is displayed. Based on the illustration,
select the finger to be recognized, and then click Next. Previously
enrolled fingerprints would have green check marks. The fingerprint
being enrolled now would have a red check mark. If any of the
previously enrolled fingerprints is selected again, the latest information
will be enrolled and previous information over-written.
4-6 User’s Manual

Operating Basics
We recommend first-timers to click Practice, and then swipe the finger as a

practice.
5. The Capture Fingerprint screen is displayed. Follow the onscreen
instructions and use the same finger you have selected under Choose
Finger to swipe three times to allow the sensor to read the fingerprint.
The fingerprint will be shown in green if properly read, or in red if the
reading is abnormal.
6. The Verify Fingerprint screen is displayed. Swipe the finger again to
allow the sensor to read again. When the Verification Successful
message is displayed, click Next.
In case of finger injury or authentication failure, it is recommended that
another fingerprint also be enrolled. The following message will be
displayed:
“It is recommended that you enroll at least two fingers. Would you like to
enroll an additional finger now?”
Click Yes and repeat steps 3, 4, 5 with another finger.
7. The Audio and Taskbar Settings screen is displayed. Click Next.
The Congratulations screen is displayed. Click Done.
8. Click Yes when the following message appears:
“OmniPass has successfully created the new user. Would you like
OmniPass to log on the new user? Once logged on, passwords can be
remembered for the new user.”
This completes the fingerprint registration process.
Window Logon via Fingerprint Authentication

Fingerprint authentication allows you to automatically logon to Windows
rather than having to enter the usual Windows ID and password.
This is especially useful when many users are using the PC, as it means
that user selection can be skipped.
Fingerprint Authentication Procedure

1. Start up the computer.
2. The Logon Authorization screen is displayed. Choose any of the
enrolled fingers and swipe the fingerprint on the sensor.
If authentication is successful, the user will be logged on to Windows.
If the fingerprint authentication fails, please logon using the Windows logon
password.
Please logon using the Windows logon password if the fingerprint
authentication failed for three consecutive tries. To logon using the
Windows logon password, enter the Windows logon password at the
“Welcome” screen as normal.
A warning message will be displayed when authentication is abnormal or
authentication is not successful within a fixed duration.
User’s Manual 4-7

Operating Basics
How to swipe the finger

Using the following steps when swiping fingers for fingerprint registration or
authentication will help to minimize authentication failures:
1. Align the first joint of the finger to the center of the sensor. Lightly touch
the sensor and swipe finger levelly towards you.
While lightly touching the sensor, swipe the finger towards you until the
sensor surface becomes visible.
Ensure the center of the fingerprint is on the sensor when swiping the
finger.
2. Scroll:
The screen can be scrolled up or down by sliding the finger over the
Fingerprint Sensor.
3. Click (Double-click:) :
TOSHIBA Quick Launcher will start up when the Fingerprint Sensor is
double-clicked using the finger.
4. Click (Tap once) :
TOSHIBA Quick Launcher items can be selected by clicking on the
Fingerprint Sensor with the finger.
■ Avoid swiping with the finger stiff or pressed-on too hard
Fingerprint reading may fail if the center of the fingerprint is not
touching on the sensor, or when finger is swiped while pressing hard.
Make sure that the center of the fingerprint is touching the sensor
before swiping.
■ Confirm the center of the fingerprint whirl before swiping
The thumb's fingerprint has a bigger whirl, which is prone to
misalignment and distortions. This will cause difficulty in registration
and a drop in the authentication success rate. Always confirm the
center of the fingerprint whirl so that it is swiped along the centerline of
the sensor.
■ When fingerprint reading is not successful
There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly. Follow the onscreen instructions to adjust the
speed of the swipe.
4-8 User’s Manual

Operating Basics
Using the USB floppy disk drive

The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte
floppy disks and connects to the USB port. It is supplied as standard with
some models and as an option with others. Refer to Chapter 2, The Grand
Tour, for more information.
Connecting USB floppy disk drive

To connect the drive, plug the floppy disk drive’s USB connector into a
computer’s USB port. Refer to Figure 4-3.
Make sure the connector is right side up and properly aligned with the
socket. Do not try to force the connection, doing so can damage the
connecting pins.
USB port
USB connector
Figure 4-3 Connecting the USB floppy disk drive
If you connect the USB floppy disk drive after turning on the computer,
it will take about 10 seconds for the computer to recognize the drive.
Do not disconnect and reconnect before 10 seconds has elapsed.
Disconnecting USB floppy disk drive

When you have finished using the USB floppy disk drive, follow the
procedures below to disconnect it:
1. Wait for the indicator light to go out to make sure all floppy disk activity
has stopped.
If you disconnect the USB floppy disk drive or turn off the power while the
computer is accessing the drive you may lose data or damage the floppy
disk or the drive.
2. Click the Safely Remove Hardware icon on the Task Bar.
3. Click USB floppy disk drive that you want remove.
4. Pull the USB floppy disk drive’s USB connector out of the computer’s
USB port.
User’s Manual 4-9

Operating Basics
Using optical media drives

■ The optical media drive can be used by connecting libretto DVD Dock
to this computer.
The text and illustrations in this section refer primarily to the optional
media drive. However, operation is the same for all other optical media
drives. The full-size drive provides high-performance execution of
CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm
(3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used
for CD/DVD-ROM operation. When the computer is accessing a
CD/DVD-ROM, an indicator on the drive glows. For detailed information,
refer to Chapter 8, libretto DVD Dock.
Use the WinDVD application to view DVD-Video discs.
When playing DVD-Video, always connect the AC adaptor to ensure

maximum performance. Operation on battery power might result in skipped
frames.
If you have a DVD-ROM and CD-R/RW drive, refer also to the Writing CDs
on DVD-ROM and CD-R/RW drive section for precautions on writing to
CDs.
If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on
DVD Super Multi drive section for precautions on writing to CDs/DVDs.
Loading discs
To load CD/DVDs, follow the steps below and refer to figures 4-4 to 4-7.
1. When the computer’s power is on, press the eject button to open the
disc tray slightly.
Eject Button
Figure 4-4 Pressing the eject button

Operating Basics
2. Grasp the disc tray gently and pull until it is fully opened.
Disc tray
Figure 4-5 Pulling the disc tray open
3. Lay the CD/DVD, label side up, in the disc tray.
Laser lens
Figure 4-6 Inserting a CD/DVD
When the disc tray is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the disc tray. After seating the CD/DVD,
however, make sure it lies flat, as shown in figure 4-6.
■ Do not touch a laser lens and its circumference portion. Doing so could
cause misalignment.
■ Prevent foreign objects from entering the drive. Check the surface of
the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.
■ Never use a cracked, deformed or repaired CD or DVD. Fragments
from a damaged CD or DVD could cause injury.

Operating Basics
4. Press gently at the center of the CD/DVD until you feel it click into
place. The CD/DVD should lie below the top of the spindle, flush with
the spindle base..
5. Push the center of the disc tray to close it. Press gently until it locks into
place.
■ Always keep fingers away from the sides of the tray when closing the
tray of an optical drive (CD/DVD drive, CD-RW drive, Multi-drive or
equivalent drive) to avoid pinching your fingers.
■ If the CD/DVD is not seated properly when the disc tray is closed, the
CD/DVD might be damaged. Also, the disc tray might not open fully
when you press the eject button.
Figure 4-7 Closing the CD/DVD disc tray
Removing discs
To remove the CD/DVD, follow the steps below and refer to figure 4-8.
Do not press the eject button while the computer is accessing the media
drive. Wait for the Optical media drive indicator to go out before you open
the disc tray. Also, if the CD/DVD is spinning when you open the disc tray,
wait for it to stop before you remove it.
1. To pop the disc tray partially open, press the eject button. Gently pull
the disc tray out until it is fully opened.
When the disc tray pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the disc tray fully open.

Operating Basics
2. The CD/DVD extends slightly over the sides of the disc tray so you can
hold it. Hold the CD/DVD gently and lift it out.
Figure 4-8 Removing a CD/DVD
3. Push the center of the disc tray to close it. Press gently until it locks into
place.
How to remove CD/DVD when the disk tray will not open
Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole just to the right of the eject button.
Eject hole
15
mm
Figure 4-9 Manual release with the eject hole
Turn off the power before you use the eject hole. If the CD/DVD is spinning
when you open the disc tray, the CD/DVD could fly off the spindle and
cause injury.

Operating Basics
Writing CDs on DVD-ROM and CD-R/RW drive

Depending on the type of drive installed, you may be able to write CDs. The
DVD-ROM and CD-R/RW drive lets you write as well as read CD-ROMs.
Observe the precautions in this section to ensure the best performance for
writing CDs. For information on loading and unloading CDs refer to the
Using optical media drives section.
■ CD-R discs can be written to only once. CD-RW discs can be rewritten
many times.
■ When the power of the optical media drive is off, the disc tray will not
open even if the eject button is pushed. Use the optical media drive
power button to turn the power of the optical media drive on. Refer to
Chapter 1, Special features.
■ Do not turn off the power of the optical media drive while the computer
is accessing the drive. If you turn off the power, you may lose data.
When writing to media using an optical drive, always connect the AC

adaptor to a power plug socket. If data is written while powered by the
batteries, writing may sometimes fail due to low battery power and data
loss may occur.
Before writing or rewriting

Please observe the following points when you write or rewrite the data.
■ We recommend the following manufacturers of CD-R and CD-RW
media. Media quality can affect write or rewrite success rates.
CD-R:
TAIYO YUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW:
RICOH Co., Ltd.
Multi-Speed and High-Speed CD-RW:

RICOH Co., Ltd.
For the below special media, the following manufacturer is recommended:
Ultra-Speed CD-RW:

Operating Basics
TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.
■ The actual number of rewrites to CD-RW is affected by the quality of the
disc and the way it is used.
■ Be sure to connect the AC adaptor when you write or rewrite.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver which can put a heavy load
on the CPU.
■ Operate the computer at full power. Do not use power-saving features.
■ Do not write while virus check software is running. Wait for it to finish,
then disable virus detection programs including any software that
checks files automatically in the background.
■ Do not use hard disk utilities, including those intended to enhance hard
disk drive access speeds. They may cause unstable operation and
damage data.
■ Write from the computer's hard disk drive to the CD. Do not try to write
from shared devices such as a LAN server or any other network device.
■ Writing with software other than Sonic RecordNow! has not been
confirmed. Therefore, operation with other software cannot be
guaranteed.
When writing or rewriting

Note the following when you write or rewrite a CD-R or CD-RW.
■ Always copy data from the hard disk drive to the CD. Do not use cut-
and-paste as the original data will be lost if there is a write error.
■ Do not perform any of the following actions:
■ Change users in the Windows XP operating system.
■ Operate the computer for any other function, including use of a
mouse or AccuPoint, closing/opening the LCD panel.
■ Start a communication application such as a modem.
■ Apply impact or vibration to the computer.
■ Install, remove or connect external devices, including the following:
PC card, SD card, USB devices, external monitor, i.LINK devices,
optical digital devices.
■ Open the optical media drive.
■ If the media is poor in quality, dirty or damaged, writing or rewriting
errors may occur.
■ Set the computer on a level surface and avoid places subject to
vibration such as airplanes, trains or cars. Do not use an unstable
surface such as a stand.
■ Keep mobile phones and other wireless communication devices away
from the computer.

Operating Basics
Writing CD/DVDs on DVD Super Multi drive

You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
preinstalled: RecordNow!, and DLA licensed by Sonic Solutions. InterVideo
WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc.
■ CD-R discs can be written to only once. CD-RW discs can be rewritten
many times.
■ DVD-R discs can be written to only once. DVD-RW discs can be
rewritten many times.
■ When the power of the optical media drive is off, the disc tray will not
open even if the eject button is pushed. Use the optical media drive
power button to turn the power of the optical media drive on. Refer to
Chapter 1, Special features.
■ Do not turn off the power of the optical media drive while the computer
is accessing the drive. If you turn off the power, you may lose data.
When writing to media using an optical drive, always connect the AC

adaptor to a power plug socket. If data is written while powered by the
batteries, writing may sometimes fail due to low battery power and data
loss may occur.
Important message
Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
disc, read and follow all setup and operating instructions in this section.
If you fail to do so, the DVD Super Multi drive may not function properly,
and you may fail to write or rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may
be caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.
■ Damage that may be caused by using third party equipment or
software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.

Operating Basics
Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the
following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
disc. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.
CD-R:
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW: (Multi-Speed and High-Speed)
RICOH Co., Ltd.
CD-RW: (Ultra-Speed)
DVD-R:
DVD Specifications for Recordable Disc for General Version 2.0
Matsushita Electric Industrial Co., Ltd.
DVD+R:
RICOH Co., Ltd.
DVD-RW:
DVD Specifications for Recordable Disc for Version 1.1 or version
1.2
VICTOR COMPANY OF JAPAN.LIMITED
DVD+RW:
RICOH Co., Ltd.
DVD-RAM:
DVD Specifications for DVD-RAM Disc for Version 2.0 or Version
2.1
Matsushita Electric Industrial Co., Ltd.
Hitachi Maxell Ltd.

Operating Basics
This drive cannot use discs that allow writing faster than 8 speed
(DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM).
■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors

may occur. Be careful to check the disc for dirt or damage before you
use it.
■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or
DVD-RAM is affected by the quality of the disc and the way it is used.
■ There are two types of DVD-R discs: authoring and general use discs.
Do not use authoring discs. Only general use discs can be written to by
a computer drive.
■ You can use DVD-RAM discs that can be removed from a cartridge and
DVD-RAM discs designed without a cartridge. You cannot use a disc
with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity.
■ Other DVD-ROM drives for computers or other DVD players may not be
able to read DVD-R/-RW or DVD+R/+RW discs.
■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in
whole or in part.
■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and
DVD-RAM disc cannot be recovered. Check the content of the disc
carefully before you delete it. If multiple drives that can write data to
discs are connected, be careful not to delete data from the wrong drive.
■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc
space is required for file management, so you may not be able to write
the full capacity of the disc.
■ Since the disc is based on the DVD standard, it might be filled with
dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.
■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000
without DVD-RAM Driver Software.
■ When multiple drives that can write data to discs are connected,
be careful not to write to the wrong drive.
■ Be sure to connect the AC adaptor before you write or rewrite.
■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM
writing. Writing is finished if you can eject DVD-RAM media.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver, which can put a heavy load
on the CPU.
■ Operate the computer in the full-power mode. Do not use power-saving
features.
■ Do not write while virus check software is running. Wait for it to finish
and then disable virus detection programs including any software that
checks files automatically in the background.

Operating Basics
■ Do not use hard disk utilities, including those intended to enhance hard
disk drive access speed. They may cause unstable operation and data
damage.
■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost
or damaged.
■ Write from the computer's hard disk drive to the CD/DVD. Do not try to
write from shared devices such as a LAN server or any other network
device.
■ Writing with software other than RecordNow! and InterVideo WinDVD
Creator Platinum are not recommended.
When writing or rewriting

Please observe/consider the following when you write or rewrite to a
CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.
■ Do not perform any of the following actions when writing or rewriting:
■ Change users in the Windows XP operating system.
■ Operate the computer for any other function, including using a
mouse or AccuPoint or closing/opening the LCD panel.
■ Start a communication application such as a modem.
■ Apply impact or vibration to the computer.
■ Install, remove or connect external devices, including the following:
PC card, SD card, USB devices, external monitor, i.LINK devices,
optical digital devices.
■ Use the Audio/Video control button to reproduce music or voice.
■ Do not use shut down/log off and standby/hibernation while writing or
rewriting.
■ Make sure writing or rewriting is completed before going into
standby/hibernation. Writing is completed if you can open the
DVD-ROM and CD-R/RW or DVD Super Multi drive tray.
■ Set the computer on a level surface and avoid places subject to
vibration such as airplanes, trains, or cars. Do not use an unstable
surface such as a stand.
■ Keep mobile phones and other wireless communication devices away
from the computer.
■ Always copy data from the hard disk drive to the DVD-RAM media.
Do not use cut-and-paste. The original data will be lost if there is a write
error.

Operating Basics
RecordNow! Basic for TOSHIBA

Note the following limitations when you use RecordNow!:
■ DVD-Video cannot be created using RecordNow!.
■ DVD-Audio cannot be created using RecordNow!.
■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player”
function to record music to the DVD-R/-RW or DVD+R/+RW disc.
■ Do not use the “Exact Copy” function of RecordNow! to copy
DVD-Video and DVD-ROM with copyright protection.
■ DVD-RAM disc cannot be backed up with the “Exact Copy” function of
RecordNow!.
■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or
DVD+R/+RW using the “Exact Copy” function of RecordNow!.
■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or
DVD+R/+RW to CD-R/RW using the “Exact Copy” function of
RecordNow!.
■ RecordNow! cannot record in packet format.
■ You might not be able to use the “Exact Copy” function of RecordNow!
to back up a DVD-R/-RW or DVD+R/+RW disc that was made with
other software on a different DVD-R/-RW or DVD+R/+RW recorder.
■ If you add data to a DVD-R and DVD+R disc that you have already
recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows Me. In Windows NT4, you will need
Service Pack 6 or later to read added data. In Windows 2000,
you will need Service Pack 2 or later to read it. Some DVD-ROM and
DVD-ROM and CD-R/RW drives cannot read added data regardless of
the operating system.
■ RecordNow! does not support recording to DVD-RAM discs. To record
to a DVD-RAM, use Explorer or other utility.
■ When you back up a DVD disc, be sure the source drive supports
recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs, it
might not be backed up correctly.
■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to
use the same type of disc.
■ You cannot partially delete any data written to a CD-RW, DVD-RW or
DVD+RW disc.

Operating Basics
Data Verification
To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.
1. Click the Options button ( ) on the RecordNow! Console to open the

Options panels.
2. Select the Data in the left-side menu.
3. Mark the Verify data written to the disc after burning check box in the
Data Options.
Click the OK button.
DLA for TOSHIBA

Note the following limitations when you use DLA:
■ This software supports only rewritable discs (DVD+RW, DVD-RW,
and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that
are not rewritable.
■ DLA does not support formatting and writing to a DVD-RAM disc -
these functions are performed by DVD-RAM Driver Software. Even if
the DLA Format menu appears when inserting a DVD-RAM disc and
right-clicking the drive icon in Windows Explorer, you should use the
‘DVDForm’ command to format this disc. You can run ‘DVDForm’ by
clicking the Start button on the taskbar to display the Start menu and
then selecting ‘All Programs’, ‘DVD-RAM’, ‘DVD-RAM Driver’ and
‘DVDForm’ sequentially.
■ Do not use any discs that have been formatted with packet writing
software other than DLA. Similarly, do not use any discs that have been
formatted with DLA with any packet writing software other than DLA.
When using a disc you are not familiar with, format it by selecting “Full
Format” before using it.
■ Do not use the Cut & Paste function for files and folders. A file or folder
that has been cut may be lost if writing fails due to an error on the disc.
■ When writing any setup files for an application to a disc formatted by
DLA, and attempting to start Setup from this disc, an error may occur.
In this case, please copy the files to your hard disk and then run Setup
from there.

Operating Basics
When using WinDVD Creator Platinum

You can record video back to your digital camcorder via i.LINK (IEEE1394)
using WinDVD Creator Platinum. However, there is a case where its
playback sound appears choppy - in this instance please follow the
instructions below:
1. Click start and select the Control Panel.
2. Click the Performance and Maintenance icon in the Control Panel.
3. Click the System icon in the Performance and Maintenance window.
4. Click the Advanced tab in the System Properties window.
5. Click the Settings icon in the “Performance” section.
6. Click the Advanced tab in the Performance Options window.
7. Click the Change icon in the “virtual memory” section.
8. Select the Custom size button in the Virtual Memory window.
9. Specify much higher values for “Initial size” and “Maximum size.”
10. Click the Set button in the Virtual Memory window.
11. Click the OK button in the Virtual Memory window.
How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:
1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] - [InterVideo
WinDVD Creator] to launch WinDVD Creator.
2. Click [Capture] button then capture the video data from the DV-
Camcorder via IEEE1394.
3. Click [Edit] button then drag the video clips from [Video Library] tab to
the edit track.
4. Click [Make Movie] button in the top bar.
5. Double Click the Right arrow button icon in the center of right side.
6. Put a blank DVD-R/+R disc or an erased DVD-RW/+RW disc in the
drive.
7. Click [Start] to record to the disc.
8. When recording is finished, the tray opens.
How to learn more about InterVideo WinDVD Creator

Please refer to the on-line Help for additional InterVideo WinDVD Creator
information.

Operating Basics
Important information for use

Note the following limitations when you write to a video DVD:
1. Editing digital video
■ Log in with Administrator rights to use WinDVD Creator.
■ Make sure that your computer is running on AC power when using
WinDVD Creator.
■ Operate the computer at Full Power. Do not use power-saving
features.
■ While you are editing a DVD video, you can display previews.
However, if another application is running, the preview might not
display properly.
■ WinDVD Creator cannot show video on the external monitor when in
simultaneous mode.
■ WinDVD Creator cannot edit or play copy protected content.
■ Do not change display settings while using WinDVD Creator.
■ Do not enter standby/hibernation mode while using WinDVD
Creator.
■ Do not operate WinDVD Creator immediately after turning on the
computer. Please wait until all disc drive activity has stopped.
■ When recording to a DV-Camcorder, to ensure you capture all of
your data, let the camcorder record for a few seconds before you
begin recording your actual data.
■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD
functions are not supported in this version.
■ While recording video to DVD or tape, please close all other
programs.
■ Do not run software like a screen saver because it can put a heavy
load on the CPU.
■ Do not run communication applications like a modem or a LAN.
2. Before recording the video to DVD
■ When you record to DVD media, please use only discs
recommended by the drive manufacturer.
■ Do not set the working drive to a slow device like a USB 1.1 hard
disk drive or it will fail to write the DVD.
■ Do not perform any of the following actions:
■ Operate the computer for any other function, including using a
mouse or AccuPoint or closing/opening the LCD panel.
■ Bump or cause vibration to the computer.
■ Use the Mode control button and Audio/Video control button to
reproduce music or voice.
■ Install, remove or connect external devices, including the
following:
PC card, SD card, USB devices, external monitor, i.LINK
devices, optical digital devices.

Operating Basics
■ Please verify your disc after recording important data.

■ DVD-R/+R/-RW discs cannot be written in VR format.
■ WinDVD Creator cannot export to DVD-Audio, VideoCD or miniDVD
format.
■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the
disc may only play on your computer.
■ When writing to a DVD disc, WinDVD Creator requires 2GB or more
of disk space for every one hour of video.
■ When you make a fully recorded DVD, the chapter sequence may
not play correctly.
3. About Disc Manager
■ WinDVD Creator can edit one play list on a disc.
■ WinDVD Creator might show a different thumbnail than you
previously set in CE (Consumer Electronics) DVD-RAM recorder.
■ Using the Disc Manager, you can edit DVD-VR format on
DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video format
on DVD-RW.
4. About recorded DVDs
■ Some DVD-ROM drives for personal computers or other DVD
players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.
■ When playing your recorded disc on your computer, please use the
WinDVD software application.
■ If you use an over-used rewritable disc, the full formatting might be
locked. Please use a brand new disc.
Media care
This section provides tips on protecting data stored on your CD/DVDs and
floppy disks.
Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them:
CD/DVDs
1. Store your CD/DVDs in the container they came in to protect them and
keep them clean.
2. Hold the CD/DVD by its outside edge or the edge on the center hole.
Fingerprints on the surface can prevent the drive from properly reading
data.
3. If your CD/DVDs become dusty or dirty, wipe them with a clean dry
cloth. Wipe from the center out, do not wipe in a circular direction
around the CD/DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.

Operating Basics
4. Take proper care of your CD/DVDs to avoid data loss or damage to the
disc or to the optical drive.
■ Never bend a CD/DVD.
■ Never damage the surface of a CD/DVD.
■ Never place the CD/DVD in direct sunlight.
■ Never expose the CD/DVD to extreme heat or cold.
■ Never place a heavy object on a CD/DVD.
■ Never write on, or otherwise mar, the read surface of a CD/DVD.
Floppy disks
1. Store your floppy disks in the container they came in to protect them
and keep them clean. If a floppy disk is dirty, do not use cleaning fluid.
Clean it with a soft damp cloth.
2. Never open the shutter or touch the magnetic surface of your floppy
disk. You could permanently damage it and lose data.
3. Always handle floppy disks with care, to prevent the loss of stored data.
Always apply the floppy disk label in the correct location. Never apply a
new label on top of an existing one. The label could come loose and
damage the floppy drive.
4. Never use a pencil for writing on a floppy disk label. Pencil lead dust
could cause a system malfunction. Always use a felt-tipped pen.
When writing a title on a label, first write on the label, then apply the
label to the floppy disk.
5. Never put a floppy disk in a location where water or other liquid may
contact it or where it is excessively damp. It could cause data loss.
Never use a wet or damp floppy disk. It could damage the floppy disk
drive or other devices.
6. Data may be lost if the floppy disk is twisted; bent; or exposed to direct
sunlight, extreme heat or cold.
7. Do not place heavy objects on your floppy disks.
8. Do not eat, smoke, or use erasers near your floppy disks. Foreign
particles inside the floppy disk’s jacket can damage the magnetic
surface.
9. Magnetic energy can destroy the data on your floppy disks. Keep your
floppy disks away from speakers, radios, television sets and other
sources of magnetic fields.

Operating Basics
Sound System
Using the microphone
A microphone connected to the external microphone jack can be used to
record monaural sounds into your applications. It can also be used to issue
voice commands to applications that support such functions.
Using a microphone and speaker, “howling” may be heard under certain
conditions. Howling occurs when sound from the speaker is picked up in
the microphone and amplified back to the speaker, which amplifies it again
to the microphone.
This howling occurs repeatedly and causes a very loud, high-pitched noise.
It is a common phenomenon that occurs in any sound system when the
microphone input is output to the speaker (throughput) and the speaker
volume is too loud or too close to the microphone. You can control
throughput by adjusting the volume of your speaker or through the Mute
function.
To adjust the volume or activate Mute, click start, point to All Programs,
point to Accessories, point to Entertainment and click Volume control.
In the Master volume panel, you can use the slide bars to adjust the
volume level or click Mute at the bottom of the panel.
SoundMAX control panel

The SoundMAX control panel lets you control additional functions for the
Microphone Enhancement and Audio Power Management. To launch the
SoundMAX Control Panel, follow the steps below.
1. Click start and click Control Panel.
2. If you are viewing the Control Panel in Category View, click on Switch
to Classic View.
3. Double-click the SoundMAX icon.
The Microphone Setup allows you to optimize the microphone input
settings for your particular configuration. Choose Standard Microphone if
you have an ordinary desktop microphone. Choose Headset if you have a
wearable microphone that is positioned directly in front of your mouth.
You can launch the Setup Wizard from the Control Panel to help you to
automatically set proper microphone input volumes and ensure that your
voice input(s) are working correctly. As you speak into the microphone, the
Sound Meter indicates the audio signal that your PC is receiving.
The Noise Reduction enhancement helps to eliminate ambient noise from
the voice input signal to provide a clean and clear signal to applications.
This feature can be used with any microphone.
The audio controller can be powered down when the audio function is idle.
To enable the Audio Power Management, follow the steps below.
1. Click the Power Management tab.
2. Select the Normal Power Savings in the Power Mode pull-down list.

Operating Basics
If No Power Savings is selected, the audio controller always runs.
If you require a more effective setting for the power management system,
you can select another mode such as High Power Savings. To select this
mode, follow the steps below.
1. Click the Power Management tab.
2. Select High Power Savings in the Power Mode pull-down list.
3. Input a time in Power Save Delay (Seconds).
If the High Power Saving option is selected, you will need to play an audio
file once before you use a microphone or play an audio CD.
Virtual Sound
TOSHIBA Virtual Sound works as an audio filter using SRS WOW XT and
SRS TruSurround XT functions provided by SRS Labs, Inc. in United
States. The audio filter enables you to enjoy better quality sound and music
on your computer. For more information on using the TOSHIBA Virtual
Sound, refer to its help.
Modem
This section describes how to connect and disconnect the internal modem
to and from a telephone jack.
hardware damage.

Operating Basics
Region selection
Telecommunication regulations vary from one region to another, so you will
need to make sure the internal modem’s settings are correct for the region
in which it will be used.
The built-in modem can be used only in specified countries and regions.
Using the modem in an area not specified for use may cause a system
failure. Check the specified areas carefully before using it.
To select a region, follow the steps below.

1. Click start, point to All Programs, point to TOSHIBA, point to
Networking and click Modem Region Select.
Do not use the Country/Region Select function in the Modem setup utility
in the Control Panel if the function is available. If you change the
Country/Region in the Control Panel, the change may not take effect.
2. The Region Selection icon will appear in the Windows Task Bar.
3. Click the icon with the primary mouse button to display a list of regions
that the modem supports. A sub menu for telephony location
information will also be displayed. A check will appear next to the
currently selected region and telephony location.
4. Select a region from the region menu or a telephony location from the
sub-menu.
■ When you click a region it becomes the modem’s region selection,
and the New Location for telephony will be set automatically.
■ When you select a telephony location, the corresponding region is
automatically selected and it becomes the modem’s current region
setting.
Properties menu
Click the icon with the secondary mouse button to display properties menu
on the screen.
Setting
You can enable or disable the following settings:
AutoRun Mode
The Region Select utility starts automatically when you start up the
operating system.
Open the Dialing Properties dialog box after selecting region.

The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.

A submenu appears displaying location information for telephony.

Operating Basics
Open dialog box, if the modem and Telephony Current

Location region code do not match.
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is
displayed. Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
If you are using the computer in Japan, the Telecommunications Business
Law requires that you select Japan region mode. It is illegal to use the
modem in Japan with any other selection.
Attaching the ferrite core to the modular cable

The ferrite core that attaches to the modular cable bundled with this product
is explained here. When connecting the modular cable, attaching the
bundled ferrite core to the modular cable will help to reduce noise.
To attach the ferrite core, follow the steps below.
1. Free the lock and the ferrite core is opened.
Lock
Figure 4-10 Opening the ferrite core
2. Adjust the modular cable so that it falls in the center dimple of the ferrite
core.
Please ensure that the connector of modular cable and the ferrite core
are placed around 30mm apart.
Ferrite core
Figure 4-11 Opening the ferrite core

Operating Basics
3. Wind the modular cable around the ferrite core as in the diagram shown
below.
Wind the modular cable loosely one full round around the ferrite core.
Please do not forcibly pull the modular cable when winding.
Modular cable
Figure 4-12 Furling the modular cable
4. Please ensure that the ferrite core is closed properly without the cable
or connector stuck in between. Please close properly until the core is
locked with a clicking sound.
Ferrite core
Figure 4-13 Furling the modular cable
5. Insert the modular cable connector (near to where the ferrite core is
attached) to the modem jack of the computer.
Ensure that the connector clicks and is inserted properly. Please do not
mistake the modular jack with the LAN connector as their shapes are
similar.
As a wrong insertion of the modular cable into the LAN connector can
result in product failure, please ensure that the correct jack is used
before inserting.

Operating Basics
Connecting
To connect the modular cable, follow the steps below.
The modular cable that comes with the computer must be used to connect
the modem. Connect the end of the modular cable with the core to the
computer.

hardware damage.
1. Plug one end of the modular cable into the computer’s modem jack.
2. Plug the other end of the modular cable into a telephone jack.
Modular cable
Modem jack
Telephone jack
Figure 4-14 Connecting the internal modem
Do not pull on the cable or move the computer while the cable is
connected.
If you use a storage device such as an optical drive or hard disk drive
connected to a 16-bit PC card, you might experience the following modem
problems:
■ Modem speed is slow or communication is interrupted.
■ Skips may occur in sound.

Operating Basics
Disconnecting
To disconnect the internal modular cable, follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. Disconnect the cable from the computer’s modem jack in the same
manner.
Wireless communications
The computer’s wireless communication function supports both Wireless
LAN and Bluetooth devices.
All models are provided with a Wireless Communication switch. Some
models are equipped with both Wireless LAN and Bluetooth functions.
Wireless LAN
The Wireless LAN is compatible with other LAN systems based on Direct
Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing
radio technology that complies with IEEE802.11 Wireless LAN standard
(Revision B or G) and Turbo Mode.
■ Theoretical maximum speed: 54Mbps (IEEE802.11g)
■ Theoretical maximum speed: 11Mbps (IEEE802.11b)
■ Theoretical maximum speed: 108Mbps (Turbo Mode)
■ Frequency Channel Selection (Revision B/G: 2.4 GHz)
■ Roaming over multiple channels
■ Card Power Management
■ Atheros Super GTM technology.
■ Wired Equivalent Privacy (WEP) data encryption, based on the 152 bit
encryption algorithm.
■ Advanced Encryption Standard (AES) data encryption, based on 256 bit
encryption algorithm.
■ Wi-Fi Protected Access (WPA).
■ The values shown above are the theoretical maximums for wireless
LAN standards. The actual values may differ.
■ The transmission speed over the wireless LAN, and the distance over
which the wireless LAN can reach, may vary depending on surrounding
configuration, client design and software/hardware configurations.
The transmission rate described is the theoretical maximum speed as
specified under the appropriate standard - the actual transmission
speed will be lower than the theoretical maximum speed. To use the
Atheros SuperGTM function, your client and access point must support
the corresponding feature. Performance of these functions may vary
depending on the format of data transmitted.

Operating Basics
Security
■ Be sure to enable WEP (encryption) function otherwise your computer
may be open to illegal access by an outsider through the wireless LAN
connection. If this should occur you computer may be open to intrusion,
eavesdropping and loss or destruction of stored data. TOSHIBA
strongly recommends the use to enable the WEP function.
■ TOSHIBA is not liable for the loss of data due to eavesdropping through
the use of the wireless LAN function and the damage thereof.
Bluetooth wireless technology

Bluetooth™ wireless technology eliminates the need for cables between
electronic devices such as desktop computers, printers and mobile phones.
You cannot use the built-in Bluetooth functions and an optional Bluetooth
SD card 3 simultaneously.
Bluetooth wireless technology has the following features:
Worldwide operation
The Bluetooth radio transmitter and receiver operate in the 2.4 GHz band,
which is license-free and compatible with radio systems in most countries
in the world.
Radio links
You can easily establish links between two or more devices. The link is
maintained even if the devices are not within line of sight.
Security
Two advanced security mechanisms ensure a high level of security:
■ Authentication prevents access to critical data and makes it impossible
to falsify the origin of a message.
■ Encryption prevents eavesdropping and maintains link privacy.
BluetoothTM Stack for Windows® by TOSHIBA

Please note that this software is specifically designed for the following
operating systems:
■ Microsoft® Windows® 2000 Professional
■ Microsoft® Windows® XP
Detailed information regarding the use with these operating systems is
listed below. Please refer also to the electronic information which is
included with each software.
This BluetoothTM Stack is based on BluetoothTM Version 1.1/1.2/2.0+EDR

specification. TOSHIBA cannot confirm all compatibility among any PC
products and/or other electronic devices using BluetoothTM other than
TOSHIBA mobile PCs.

Operating Basics
Release Notes related to the BluetoothTM Stack for

Windows® by TOSHIBA
1. Install:
On Windows 2000 or Windows XP, BluetoothTM Stack for Windows® by
TOSHIBA does not have a digital signature.
2. Fax application software:
Regarding FAX application software, there are some software that you
cannot use on this BluetoothTM Stack.
3. Multi User:
On Windows XP, the use of Bluetooth is not supported in a multi-user
environment. This means that, when you use Bluetooth, other users
logged onto the same computer will not be able to use its Bluetooth
functionality.
Product Support:
The latest information regarding Operating System support,
Language Support or available upgrades can be found on our web site
http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or
www.pcsupport.toshiba.com in the United States.
Wireless communication switch

You can enable or disable Wireless LAN and Bluetooth functions, with the
on/off switch. No transmissions are sent or received when the switch is off.
Slide the switch to the right to turn it off and to the left to turn it on.
■ Do not use the WiFi or Bluetooth functionalities near a microwave oven
or in areas subject to radio interference or magnetic fields. Interference
from a microwave oven or other source can disrupt WiFi or Bluetooth
operation.
■ Turn WiFi and Bluetooth functionalities off when near a person who
may have a cardiac pacemaker implant or other medical electric
device. Radio waves may affect pacemaker or medical device
operation, possibly resulting in serious injury. Follow the instruction of
your medical device when using any WiFi or Bluetooth functionality.
■ Always turn off WiFi or Bluetooth functionality if the PC is near
automatic control equipment or appliances such as automatic doors or
fire detectors. Radio waves can cause malfunction of such equipment,

Operating Basics
Wireless communication Indicator

The wireless communication indicator indicates the status of the wireless
communication functions.
Indicator status Indication
Indicator off Wireless communication switch is set to off.

Automatic power down because of overheating.
Power malfunction
Indicator glows Wireless communication switch is on. Wireless

LAN or Bluetooth is turned on by an application.
If you used the Task Bar to disable the wireless LAN, restart the computer
or perform the following procedure to re-enable it : click the following: start,
Control Panel, System, Hardware Device Manager, Network adapters,
Atheros AR5005GS Wireless Network Adapter and enable.
LAN
The computer has built-in support for Ethernet LAN (10 megabits per
second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second,
100BASE-TX).
This section describes how to connect/disconnect to a LAN.
Do not install or remove an optional memory module while Wake-up on
LAN is enabled.
The Wake-up on LAN function consumes power even when the system is
off. Leave the AC adaptor connected while using this feature.
LAN cable types
The computer must be configured properly before connecting to a LAN.

Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.
If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable or higher.
You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T),
you can connect with either a CAT5 or a CAT3.

Operating Basics
Connecting LAN cable

To connect the LAN cable, follow the steps below.
■ Connect the AC adaptor before connecting the LAN cable. The AC
adaptor must remain connected during LAN use. If you disconnect the
AC Adaptor while the computer is accessing a LAN, the system may
hang up.
■ Do not connect any other cable to the LAN jack except the LAN cable.
Otherwise, malfunctions or damage may occur.
■ Do not connect any power supplying device to the LAN cable that is
connected to the LAN jack. Otherwise, malfunctions or damage may
occur.
1. Turn off the power to the computer and to all external devices
connected to the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.
LAN jack
LAN connector
Figure 4-15 Connecting the LAN cable
3. Plug the other end of the cable into a LAN hub connector. Check with
your LAN administrator before connecting to a hub.
Disconnecting LAN cable

To disconnect the LAN cable, follow the steps below.
1. Pinch the lever on the connector in the computer’s LAN jack and pull
out the connector.
2. Disconnect the cable from the LAN hub in the same manner.
Check with your LAN administrator before disconnecting from the hub.

Operating Basics
Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.
■ Be careful not to spill liquids into the computer. If the computer does get
wet, turn the power off immediately and let the computer dry completely
before you turn it on again.
■ Clean the computer using a slightly damp (with water) cloth. You can
use glass cleaner on the LCD display screen. Spray a small amount of
cleaner on a soft, clean cloth and wipe the screen gently with the cloth.
Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.
Moving the computer

The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.
■ Before moving the computer, it is recommended that you change the
setting for the HDD Protection feature. Refer to the section, Using the
Hard Disk Drive (HDD) Protection, in this chapter.
■ Make sure all disk activity has ended before moving the computer.
Check the HDD indicator on the computer.
■ If a CD/DVD is in the drives, remove it. Also make sure the disc tray is
securely closed.
■ Turn off the power to the computer.
■ Disconnect the AC adaptor and all peripherals before moving the
computer.
■ Close the LCD display panel. Do not pick up the computer by its panel.
■ Before carrying your PC, shut down the PC, disconnect the power cable
and wait until the PC cools down. Failure to follow this instruction could
result in minor injury.
■ Always turn off the power when you move the PC. If the power button
has a lock, set it to the lock position. Also be careful not to subject the
PC to impact. Failure to follow this instruction could result in damage to
PC, PC failure or loss of data.
■ Never transport your PC with PC cards installed. This could cause
damage to your PC and/or PC card, resulting in product failure.
■ Use the carrying case when transporting the computer.
■ When carrying your computer, be sure to hold it securely so that it does
not fall or hit anything.
■ Do not carry your computer by holding protruded portions.

Operating Basics
Using the Hard Disk Drive (HDD) Protection

This computer includes a feature for reducing the risk of damage to the
hard disk drive.
Using the acceleration sensor built in the computer, HDD Protection detects
vibration, shocks and similar signs, and automatically moves the hard disk
drive head to a safe position in order to reduce the risk of damage that
could be caused by a head-to-disk contact.
■ This function does not guarantee that the hard disk drive will not be
damaged.
■ A secondary hard disk drive fitted to the computer is not supported by
the HDD protection function.
When vibration is detected, the following message is displayed, and the

icon in the notification area of the taskbar is changed to the protection
state. This message is displayed until the OK button is pressed or
30 seconds pass. When vibration subsides, the icon returns to the normal
state.
Figure 4-16 HDD Protection Message
Taskbar Icon
State Icon Description
Normal HDD Protection is enabled.
Protection HDD Protection is active. The hard disk drive

head is in a safe position.
OFF HDD Protection is disabled.

Operating Basics
TOSHIBA HDD Protection Properties

You can change the HDD Protection settings by using the TOSHIBA HDD
Protection Properties window. To open this window, click start point to All
Programs, point to TOSHIBA, point to Utilities and click HDD Protection
setting. The window can also be started from the icon on the Taskbar, or
from the Control Panel.
Figure 4-17 TOSHIBA HDD Protection Properties
HDD Protection
You can choose whether to enable or disable HDD Protection.
Detection Level
This function can be set to four levels. The sensitivity levels in which
vibrations, impacts and their similar signs are detected can be set to OFF,
1, 2, and 3 in ascending order. Level 3 is recommended for better
protection of the computer. However, when the computer is used as
handheld or in other unstable conditions, setting the detection level to 3
could result in frequent execution of HDD Protection, which will slow HDD
reading and writing. Set a lower detection level when the speed of HDD
reading and writing is a priority.

Operating Basics
Different detection levels can be set depending on whether the computer is

used as handheld or mobile usages, or whether it is used in a stable
environment such as on a table in the workplace or at home. By setting
different detection levels for the computer depending on whether it runs
with the AC power (desktop) or with batteries (handheld or mobile usage),
the detection level automatically switches according to the power
connection mode. Furthermore, the detection level can be individually set
also during use in Tablet mode (Battery).
Detail Properties
To open the Detail Properties window, click the Setup Detail button in the
TOSHIBA HDD Protection Properties window.
Figure 4-18 Detail Properties
Detection Level Amplification

When the AC adaptor is disconnected or the lid is closed, HDD Detection
assumes that the computer will be carried and sets the detection level to
the maximum for 10 seconds.
HDD Protection Message

Specify whether to display a message when HDD Protection is active.
This function does not work when the computer is starting, in standby,
in hibernation, in transition to hibernation, recovering from hibernation,
or powered off. Be sure to not subject the computer to vibration or impact
while the function is disabled.

Operating Basics
Heat dispersal
To protect from overheating, the CPU has an internal temperature sensor.
If the computer’s internal temperature rises to a certain level, the cooling
fan is turned on or the processing speed is lowered. You can select
whether to control the CPU temperature by turning on the fan first, then if
necessary, lowering the CPU speed. Or, by lowering the CPU speed first,
then if necessary, turning on the fan. Use the Cooling Method item of the
Basic Setup tab in TOSHIBA Power Saver.
When the CPU temperature falls to a normal range, the fan is turned off
and the CPU operation returns to standard speed.
If the CPU temperature reaches an unacceptably high level with either
setting, the system automatically shuts down to prevent damage. Data in
memory will be lost.

Operating Basics

libretto U100
Chapter 5
The Keyboard
The computer’s keyboard layouts are compatible with a 101/102-key

enhanced keyboard. By pressing some keys in combination, all the
101/102-key keyboard functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region’s
keyboard layout your computer is configured with. Keyboards for numerous
languages are available.
There are six types of keys: typewriter keys, function keys, soft keys,
Hot keys, Windows special keys and keypad overlay.
Typewriter keys
The typewriter keys produce the upper- and lower-case letters, numbers,
punctuation marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and
using a computer keyboard:
■ Letters and numbers produced in computer text vary in width. Spaces,
which are created by a “space character,” may also vary depending on
line justification and other factors.
■ The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
■ The uppercase O (oh) and the 0 (zero) are not interchangeable.
■ The Caps Lock function key locks only the alphabetic characters in
uppercase while the shift lock on a typewriter places all keys in the
shifted position.
■ The Shift keys, the Tab key, and the BkSp (backspace) key perform the
same function as their typewriter counterparts but also have special
computer functions.
User’s Manual 5-1

The Keyboard
Function keys: F1 … F12

The function keys (not to be confused with Fn) are the 12 keys at the top of
your keyboard. These keys function differently from other keys.
F1 through F12 are called function keys because they execute

programmed functions when pressed. Used in combination with the Fn key,
keys marked with icons execute specific functions on the computer. Refer
to the section, Soft keys: Fn key combinations, in this chapter. The function
executed by individual keys depends on the software you are using.
Soft keys: Fn key combinations

The Fn (function) is unique to TOSHIBA computers and is used in
combination with other keys to form soft keys. Soft keys are key
combinations that enable, disable or configure specific features.
Some software may disable or interfere with soft-key operations.
Soft-key settings are not restored by the Standby feature.
Emulating keys on enhanced keyboard
PrtSc Scroll Pause

Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
SysReq lock Break
~ ! @ # $ % & * ( ) _ + Num
^6 Bk Sp Ins Home PgUp / *.
` 1 2 3 4 5 7 8 9 0 - = Lock
{ } 7 8 9
Tab Q W E R T Y U I O P [ ] \ Del End PgDn
Home PgUp
+
: ,, 4 5 6
A S D F G H J K L Enter
CapsLock
; ,
< > ? 1 2 3
Shift Z X C V B N M , . Shift
/ End PgDn
Enter
0 .
Ctrl Alt Alt Ctrl
Ins Del
Figure 5-1 A 101-key enhanced keyboard layout
The keyboard is designed to provide all the features of the 101-key

enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced
keyboard has a numeric keypad and scroll lock key. It also has additional
Enter and Ctrl keys to the right of the main keyboard. Since the keyboard
is smaller and has fewer keys, some of the enhanced keyboard functions
must be simulated using two keys instead of one on the larger keyboard.
Your software may require you to use keys that the keyboard does not
have. Pressing the Fn key and one of the following keys simulates the
enhanced keyboard’s functions.
5-2 User’s Manual

The Keyboard
Press Fn + F10 or Fn + F11 to access the integrated keypad. When

activated, the keys with gray markings on the bottom edge become
numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to
the Keypad overlay section in this chapter for more information on how to
operate these keys. The power on default for both settings is off.
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power
on default is off.
Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric

keypad.
Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.
Press FN + PGUP to move to last page.
Press FN + PGDN to move to next page.
Press FN + INS, when you change insertion/overwrite of the input mode of

a character.
User’s Manual 5-3

The Keyboard
Hot keys
Hot keys (Fn + a function or Esc key) let you enable or disable certain
features of the computers.
Sound mute: Pressing Fn + Esc in a Windows environment turns sound

on or off. When you press these hot keys, the current setting will change
and be displayed as an icon.
Instant security: Press Fn + F1 to blank the screen to prevent others from

accessing your data. To restore the screen and original settings, press any
key or press the AccuPoint. If a screensaver password is registered, a
dialog box will appear. Enter the screensaver password and click OK.
If no password is set, the screen will be restored when you press any key or
press the AccuPoint.
Power save mode: Pressing Fn + F2 changes the power save mode.

If you press Fn + F2 in a Windows environment, the settings dialog box for
the Power Save Mode will be displayed. Continue holding down Fn, and
release and press F2 again to toggle between the settings. Release both
Fn and F2 to put the new setting into effect. You can also change this
setting through the Profile options in TOSHIBA Power Saver.
Standby: When you press Fn + F3, the computer enters the Standby
mode. Before entering Standby, a dialog box appears asking for your
confirmation. This dialog box will not be displayed in the future when you
click the check box.
5-4 User’s Manual

The Keyboard
Hibernation: When you press Fn + F4, the computer enters the

Hibernation mode. Before entering Hibernation, a dialog box appears
asking for your confirmation. This dialog box will not be displayed in the
future when you click the check box.
Display selection: Press Fn + F5 to change the active display device.

When you press these hot keys, a dialog box appears. Only selectable
devices will be displayed. Hold down Fn and press F5 again to change the
device. When you release Fn and F5, the selected device will change.
If you hold down these hot keys for five seconds the selection will return to
the internal LCD.
Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD

screen brightness in decrements. When you press these hot keys, the
current setting will be displayed for two seconds by an icon. You can also
change this setting through the Screen brightness item of the Basic Setup
tab in TOSHIBA Power Saver.
Internal LCD screen Brightness: Pressing Fn + F7 increases the LCD

screen brightness in increments. When you press these hot keys, the
current setting will be displayed for two seconds by a pop-up icon. You can
also change this setting through the Screen brightness item of the Basic
Setup tab in TOSHIBA Power Saver.
.
■ The brightness level is always set at the maximum value for about 18
seconds, when the internal LCD screen turns on. After 18 seconds, the
brightness level will appear at the Power Save Mode setting or you can
change it manually.
■ LCD screen clarity increases with the brightness level.
User’s Manual 5-5

The Keyboard
Wireless setting: If your computer has both Wireless LAN and Bluetooth
functions, you can press Fn + F8 to select which type of wireless
communication you want to use. When you press these hot keys, a dialog
box will appear. Continue holding down Fn and press F8 to change the
setting. If wireless communication is turned off, Disabled Wireless
Communication Switch will be displayed.
If no wireless communication device is installed, no dialog box will appear.
LCD screen resolution selection: Press Fn + Space keys to change the

LCD screen resolution. Each time when you press these hot keys, the LCD
screen resolution changes as follows: With XGA, you can change the
resolution between 800 × 600 and 1280 × 768 pixels.
TOSHIBA Zooming Utility (reduce): To reduce the icon size on the

desktop or the application window, press the 1 key while holding down the
Fn key.
TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the

desktop or the application window, press the 2 key while holding down the
Fn key.
Fn Sticky key
You can use the TOSHIBA Accessibility Utility to make the Fn key sticky,
that is, you can press it once, release it, and then press an “F number” key.
To start the TOSHIBA Accessibility Utility, click start, point to All
Programs, point to TOSHIBA, point to Utilities and click Accessibility.
5-6 User’s Manual

The Keyboard
Windows special keys

The keyboard provides two keys that have special functions in Windows:
Windows logo key activates the start menu and the other, the application
key, has the same function as the secondary mouse button.
This key activates the Windows start menu.
This key has the same function as the secondary mouse button.
Keypad overlay
Your computer’s keyboard does not have an independent numeric keypad,
but its numeric keypad overlay functions like one.
The keys in the center of the keyboard with gray letters make up the
numeric keypad overlay. The overlay provides the same functions as the
numeric keypad on the 101/102-key enhanced keyboard in figure 5-2.
Turning on the overlays

The numeric keypad overlay can be used for numeric data input or cursor
and page control.
Arrow mode
To turn on the Arrow mode, press Fn + F10. Now try cursor and page
control using the keys shown in figure 5-2. Press Fn + F10 again to turn off
the overlay.
User’s Manual 5-7

The Keyboard
Numeric mode
To turn on the Numeric mode, press Fn + F11. Now try numeric data entry
using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay.
Figure 5-2 The numeric keypad overlay
Temporarily using normal keyboard (overlay on)

While using the overlay, you can temporarily access the normal keyboard
without turning off the overlay:
1. Hold Fn and press any other key. All keys will operate as if the overlay
were off.
2. Type upper-case characters by holding Fn + Shift and pressing a
character key.
3. Release Fn to continue using the overlay.
Temporarily using overlay (overlay off)

While using the normal keyboard, you can temporarily use the keypad
overlay without turning it on:
1. Press and hold down Fn.
2. Check the keyboard indicators. Pressing Fn turns on the most recently
used overlay. If the Numeric mode indicator lights, you can use the
overlay for numeric entry. If the Arrow mode indicator lights, you can
use the overlay for cursor and page control.
3. Release Fn to return to normal keyboard operation.
5-8 User’s Manual

The Keyboard
Temporarily changing modes

If the computer is in Numeric mode, you can switch temporarily to Arrow
mode by pressing a shift key.
If the computer is in Arrow mode, you can switch temporarily to Numeric
mode by pressing a shift key.
Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard
operation. But, you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold down Alt + Fn.
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display
screen.
User’s Manual 5-9

The Keyboard

libretto U100
Chapter 6
Power and Power-Up Modes
The computer’s power resources include the AC adaptor, battery pack and
internal batteries. This chapter gives details on making the most effective
use of these resources including charging and changing batteries, tips for
saving battery power, and power up modes.
Power conditions
The computer’s operating capability and battery charge status are affected
by the power conditions: whether an AC adaptor is connected, whether a
battery pack is installed and what the charge level is for the battery.
Table 6-1 Power conditions
Power on Power off (no operation)

AC Battery fully • Operates • LED: Battery green
adaptor charged • LED: Battery green DC IN green
connected
DC IN green
Battery partially • Operates • Quick charge
charged or no • Quick Charge • LED: Battery orange
charge
• LED: Battery orange DC IN green
DC IN green
No battery • Operates • No charge
installed • No charge • LED: Battery off
• LED: Battery off DC IN green
DC IN green
User’s Manual 6-1

Table 6-1 Power conditions continued
Power on Power off

(no operation)
AC Battery charge • Operates
adaptor is above low • LED: Battery off
not battery trigger
connected point DC IN off
Battery charge • Operates

is below low • LED: Battery
battery trigger
point flashes orange
DC IN off
Battery charge Computer goes into
is exhausted Hibernation mode and
shuts down
No battery • Cannot operate
installed • LED: Battery off
DC IN off
Power indicators
As shown in the above table, the Battery, DC IN and Power indicators on
the system indicator alert you to the computer’s operating capability and
battery charge status.
Battery indicators
Check the Battery indicator to determine the status of the battery pack.
The following indicator lights indicate the battery status:
Flashing orange The battery charge is low. The AC adaptor must

be connected to recharge the battery.
Orange Indicates the AC adaptor is connected and

charging the battery.
Green Indicates the AC adaptor is connected and the

battery is fully charged.
No light Under any other conditions, the indicator does

not light.
If the battery pack becomes too hot while it is being charged, the charge
will stop and the Battery indicator will go out. When the battery pack’s
temperature falls to a normal range, charge will resume. This occurs
whether the computer’s power is on or off.
6-2 User’s Manual

DC IN indicator
Check the DC IN indicator to determine the power status with the AC
adaptor connected:
Green Indicates the AC adaptor is connected and

supplying proper power to the computer.
Flashing orange Indicates a problem with the power supply. Plug

the AC adaptor into another power outlet. If it still
does not operate properly, contact your dealer.
No light Under any other conditions, the indicator does not

light.
Power indicator
Check the Power indicator to determine the power status:
Green Indicates power is being supplied to the computer

and the computer is turned on.
Blinking orange Indicates power is being supplied to the computer

while the computer is in Standby mode. The
indicator turns on for one second and off for two
seconds.
No light Under any other conditions, the indicator does

not light.
Battery types
The computer has two types of batteries:
■ Battery pack
■ Real Time Clock (RTC) battery
Battery pack
When the AC adaptor is not connected, the computer’s main power source
is a removable lithium ion battery pack, also referred to in this manual as
the main battery. You can purchase additional battery packs for extended
use of the computer away from an AC power source.
Before you remove the battery pack, set the computer to Hibernation mode
or save your data and shut down the computer. Do not change the battery
pack while the AC adaptor is connected.
User’s Manual 6-3

■ The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.
■ Always dispose of used battery packs in compliance with all applicable
laws and regulations. Put insulating tape, such as cellophane tape, on
the electrode during transportation to avoid a possible short circuit, fire
or electric shock. Failure to do so could possibly result in serious injury.
■ Do not remove the battery pack while the computer is in Standby mode.
Data is stored in RAM, so if the computer loses power it will be lost.
When the computer is powered off in Standby mode, and the AC
adaptor is not connected, the battery pack supplies power to maintain
data and programs in memory. If the battery pack is completely
discharged, Standby mode will not function and the computer will lose
all data in memory.
To ensure that the battery pack maintains its maximum capacity, operate
the computer on battery power at least once a month until the battery pack
is fully discharged. Refer to Extending battery life in this chapter for
procedures. If the computer is continuously operated on AC power through
an AC adaptor for an extended period, for example more than a month, the
battery may fail to retain a charge, it may not function efficiently over the
expected life of the battery and the Battery indicator may not indicate a
low-battery condition.
Real Time Clock (RTC) battery

The Real Time Clock (RTC) battery provides power for the internal real
time clock and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this
data and the real time clock and calendar stop working. The following
message appears when you turn on the power:
S **** RTC battery is low or CMOS checksum is
inconsistent ****
Press [F1] key to set Date/Time.
You can change the settings maintained by the RTC battery by pressing F1
key. Refer to Chapter 9 Troubleshooting for details on how to do this.
The computer’s RTC battery is a lithium ion battery and should be replaced
only by your dealer or by a TOSHIBA service representative. The battery
can explode if not properly replaced, used, handled or disposed of.
Dispose of the battery as required by local ordinances or regulations.
6-4 User’s Manual

Care and use of the battery pack

The battery pack is a vital component of portable computing. Taking proper
care of it will help ensure longer operating time on battery power as well as
a longer life for your battery pack. Follow the instructions in this section
carefully to ensure safe operation and maximum performance.
Safety precautions
Mishandling of battery packs can cause death, serious injury or property
damage. Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, which if not avoided,
may result in moderate or minor injury or property damage.
Note: Provides important information.
Danger
1. Never attempt to dispose of a battery pack by burning or by throwing it
into a fire, and never allow exposure to a heating apparatus (e.g.,
microwave oven). Heat can cause a battery pack to explode and
possibly cause serious injury.
2. Never attempt to disassemble, tamper with or repair a battery pack.
The battery pack could overheat and ignite. Leakage of the caustic
alkaline solution or other electrolytic substances could cause fire,
possibly resulting in death or serious injury.
3. Never short circuit the battery pack by either accidentally or intentionally
bringing the battery terminals in contact with another conductive object.
This could cause serious injury or a fire, and could also damage the
battery pack. Always wrap the battery pack in plastic (or place it in a
plastic bag) whenever transporting it, to avoid exposing the terminals to
another conductive object which could result in serious injury. Always
cover the metal terminals with insulating tape when disposing of the
battery pack, to prevent accidental short circuiting which could result in
serious injury.
4. Never drive a nail or any other sharp object into the battery pack, hit
battery pack with a hammer or other object or step on it. Doing so could
cause a fire or explosion possibly resulting in serious injury.
5. Never charge the battery pack by a method other than as instructed in
the User's Manual. Doing so could cause a fire or explosion possibly
6. Never connect the battery pack to a plug socket or a car cigarette plug
socket. The battery pack could rupture or ignite causing a fire or
explosion possibly resulting in serious injury.
User’s Manual 6-5

7. Never allow a battery pack to become wet. A wet battery pack will
overheat or ignite causing rupture or fire, possibly resulting in death or
serious injury.
8. Never store a battery pack in an area of high humidity. This could cause
a fire or explosion possibly resulting in serious injury.
9. Never expose a battery pack to abnormal shock, vibration or pressure.
The battery pack's internal protective device could fail, causing it to
overheat or ignite resulting in caustic liquid leakage, or explosion or fire,
possibly resulting in death or serious injury.
10. Never subject a battery pack to heat, and never store it or use it near a
heat source. The battery pack could ignite or explode when heated or
burned, possibly resulting in death or serious injury. Subjecting a battery
pack to heat could also cause caustic liquid to leak. It can also cause
failure, malfunction, or loss of stored data.
11. Always use the battery pack supplied as an accessory or an equivalent
battery pack specified in the User's Manual. Other battery packs have
different voltage and terminal polarities. Use of non-conforming battery
packs could generate smoke or cause fire or rupture, possibly resulting
in serious injury.
12. Never allow caustic electrolyte fluid leaked from the battery pack to
contact your eyes, body or clothing.If caustic electrolyte fluid from the
battery pack should contact your eyes, immediately wash your eyes with
large amounts of running water and obtain prompt medical attention,
to help prevent permanent eye damage. If electrolyte fluid should
contact any part of your body, immediately wash it off under running
water to help prevent skin rashes. If electrolyte fluid should contact your
clothes, promptly remove them to help prevent the electrolyte fluid from
contacting your body, possibly resulting in serious injury.
13. Always immediately turn the power off and disconnect the power cable
plug from the plug socket if you observe any of the following conditions:
■ Offensive or unusual odor
■ Excessive heat
■ Discoloration
■ Deformation
■ Smoke
■ Other unusual event during use, such as abnormal sound
In such an event, immediately remove the battery pack from the PC.
In some instances, you might have to wait for the PC to cool down
before removing the battery pack, in order to avoid any possible minor
injury due to heat exposure. Do not turn on the PC's power again until
an authorized Toshiba service provider has checked it for safety.
Continued use could cause a fire or rupture possibly resulting in serious
injury or PC failure including but not limited to the loss of data.
14. Always dispose of used battery packs in compliance with all applicable
laws and regulations. Put insulating tape, such as cellophane tape,
on the electrode during transportation to avoid a possible short circuit,
fire or electric shock. Failure to do so could possibly result in serious
injury.
6-6 User’s Manual

15. Make sure the battery is securely installed in the computer before
attempting to charge the battery pack. Improper installation could
generate smoke or fire, or cause the battery pack to rupture.
16. Keep the battery pack out of reach of infants and children.
It can cause injury.
Caution
1. Never continue to use a battery pack after its recharging capacity has
become impaired, or after the display of a warning message indicating
that the battery pack’s power is exhausted. Continued use of an
exhausted or impaired battery pack could cause the loss of data.
2. Use only battery packs recommended by TOSHIBA as replacements.
3. When installing a battery pack or before moving the PC, always make
sure the battery pack is inserted correctly and securely. If the battery
falls out, while you are carrying the PC, you could be injured or the
battery pack could be damaged.
4. Charge the battery pack only in an ambient temperature between 5 and
35 degrees Celsius. Otherwise, the electrolyte solution might leak,
battery pack performance might deteriorate and the battery life might be
shortened.
5. Never continue to use a battery pack after its recharging capability has
become impaired, or after the warning message indicating that the
battery pack power is exhausted has been displayed.
6. Continued use of an exhausted or impaired battery pack could result in
the loss of data or damage to PC.
7. Never install or remove the battery pack without first turning off the
power and disconnecting the AC adaptor. Never remove the battery
pack while the computer is in Suspend or Standby mode. Data will be
lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable
the Wake-up on LAN function.
2. To ensure the battery pack maintains maximum capacity, operate the
computer on battery power once a week until the battery pack is fully
discharged. Refer to the section Extending battery life in this chapter for
procedures. If the computer is continuously operated on AC power for
an extended period, more than a week, the battery might fail to retain a
charge. It might not function efficiently over the expected life of the
battery pack and the Battery indicator might not indicate a low-battery
condition.
3. After the battery pack is charged, avoid leaving the AC adaptor
connected and the computer turned off for more than a few hours at a
time. Continuing to charge a fully-charged battery pack can damage the
battery.
User’s Manual 6-7

Charging the batteries

When the power in the battery pack becomes low, the Battery indicator
flashes orange indicating that only a few minutes of battery power remain.
If you continue to use the computer while the Battery indicator flashes,
the computer enables Hibernation mode (so you don’t lose data) and
automatically turns off.
The computer enters Hibernate mode only if Hibernation is enabled in two
places: the Hibernate tab in Power Options and Setup Action tab in
TOSHIBA Power Saver.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack while it is installed in the computer, connect the
AC adaptor to the DC IN 15V jack and plug the other end into a working
outlet.
The Battery indicator glows orange when the battery is being charged.
Use only the computer connected to an AC power source or the optional
TOSHIBA Battery charger to charge the battery pack. Never attempt to
charge the battery pack with any other charger.
Time
The following table shows the approximate time required to fully charge a
discharged battery.
Charging time (hours)
Battery type Power on Power off
Battery pack (3400mAh) about 4.0 to 5.5 about 3.0
RTC battery 8 Doesn't charge
The charging time when the computer is on is affected by ambient

temperature, the temperature of the computer and how you use the
computer. If you make heavy use of external devices, for example,
the battery might scarcely charge at all during operation. Refer also to the
section Maximizing battery operating time.
Battery charging notice

The battery may not charge right away under the following conditions:
■ The battery is extremely hot or cold. If the battery is extremely hot,
it might not charge at all. To ensure the battery charges to its full
capacity, charge the battery at room temperature of 10° to 30°C
(50° to 88°F).
■ The battery is nearly completely discharged. Leave the AC adaptor
connected for a few minutes and the battery should begin charging.
6-8 User’s Manual

The Battery indicator may show a rapid decrease in battery operating time
when you try to charge a battery under the following conditions:
■ The battery has not been used for a long time.
■ The battery has completely discharged and been left in the computer for
a long time.
■ A cool battery is installed in a warm computer.
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power
on until the power automatically shuts off.
2. Connect the AC adaptor to the DC IN 15V jack of the computer,
and the AC adaptor into power outlet.
3. Charge the battery until the Battery indicator glows green.
Repeat these steps two or three times until the battery recovers normal
capacity.
Leaving the AC adaptor connected will shorten battery life. At least once a
month, run the computer on battery power until the battery is fully
discharged, then recharge the battery.
Monitoring battery capacity

Remaining battery power can be monitored in TOSHIBA Power Saver.
■ Wait at least 16 seconds after turning on the computer before trying to
monitor the remaining operating time. The computer needs this time to
check the battery’s remaining capacity and to calculate the remaining
operating time, based on the current power consumption rate and
remaining battery capacity. The actual remaining operating time may
differ slightly from the calculated time.
■ With repeated discharges and recharges, the battery’s capacity will
gradually decrease. Therefore, an often used, older battery will not
operate for as long as a new battery even when both are fully charged.
In this case, TOSHIBA Power Saver will indicate a 100% charge for
both the old and new battery, but the displayed estimated time
remaining will be shorter for the older battery.
User’s Manual 6-9

Maximizing battery operating time

A battery’s usefulness depends on how long it can supply power on a
single charge.
How long the charge lasts in a battery depends on:
■ How you configure the computer (for example, whether you enable
battery-power saving options). The computer provides a battery save
mode, which can be set in TOSHIBA Power Saver, to conserve battery
power. This mode has the following options:
■ CPU Processing speed
■ Screen brightness
■ Cooling Method
■ System standby
■ System Hibernation
■ Monitor Power off
■ HDD Power off
■ How often and how long you use the hard disk, optical disc and the
floppy disk drive.
■ How much charge the battery contained to begin with.
■ How you use optional devices, such as a PC card, to which the battery
supplies power.
■ Enabling Standby mode conserves battery power if you are frequently
turning the computer off and on.
■ Where you store your programs and data.
■ Closing the LCD display panel when you are not using the keyboard
saves power.
■ Operating time decreases at low temperatures.
■ The condition of the battery terminals. Make sure the battery terminals
stay clean by wiping them with a clean dry cloth before installing the
battery pack.
Retaining data with power off

When you turn off your computer with fully charged batteries, the batteries
retain data for the following approximate time periods:
Retention time
Battery type State and Retention Time
Battery pack (3400mAh) about 5 days (Standby mode)

about 40 days (Power off)
RTC battery 30 days

Extending battery life

To maximize the life of your battery pack:
■ At least once a month, disconnect the computer from a power source
and operate it on battery power until the battery pack fully discharges.
Before doing so, follow the steps below.
1. Turn off the computer’s power.
2. Disconnect the AC adaptor and turn on the computer’s power.
If it does not turn on go to step 4.
3. Operate the computer on battery power for five minutes. If the
battery pack has at least five minutes of operating time, continue
operating until the battery pack is fully discharged. If the Battery
indicator flashes or there is some other warning to indicate a low
battery, go to step 4.
4. Connect the AC adaptor to the computer and the power cord to a
power outlet. The DC IN indicator should glow green, and the
Battery indicator should glow orange to indicate that the battery
pack is being charged. If the DC IN indicator does not glow, power
is not being supplied. Check the connections for the AC adaptor
and power cord.
5. Charge the battery pack until the Battery indicator glows green.
■ If you have extra battery packs, rotate their use.

■ If you will not be using the system for an extended period,
more than one month, remove the battery pack.
■ Disconnect the AC adaptor when the battery is fully charged.
Overcharging makes the battery hot and shortens life.
■ If you are not going to use the computer for more than eight hours,
disconnect the AC adaptor.
■ Store spare battery packs in a cool dry place out of direct sunlight.

Replacing the battery pack

The battery pack is classified as a consumable item and will need to be
replaced when it reaches the end of its operating life. The operating life of
the battery will gradually reduce through repeated charging/discharging - if
the Battery indicator flashes orange shortly after fully recharging the
battery, the battery pack needs to be replaced.
You might also replace a discharged battery pack with a charged spare
when you are operating your computer away from an AC power source.
This section explains how to remove and install the battery pack.
Removing the battery pack

To replace a discharged battery pack, follow the steps below.
■ Do not remove the battery pack while the computer is in Standby mode.
Data is stored in RAM, so if the computer loses power it will be lost.
■ In Hibernation mode, data will be lost if you remove the battery pack or
disconnect the AC adaptor before the save is completed. Wait for the
HDD indicator to go out.
■ Do not touch the battery release latch while holding the computer or
you may get injured if the battery pack falls out due to the unintentional
release of the battery release latch.
1. Save your work.
2. Turn the computer’s power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Close the LCD display panel and turn the computer upside down.
5. Slide the battery lock (➀) to unlock position ( ) (Move it completely to
the left).

6. Slide and hold the battery release latch (➁) to free the battery pack for
removal, then slide out the battery pack (➂).
Battery pack
Battery release latch
Battery lock
Figure 6-1 Releasing the battery pack
7. Return your computer to the upright position.

Installing the battery pack

To install a battery pack, follow the steps below.
Do not touch the battery release latch while holding the computer or you
may get injured if the battery pack falls out due to the unintentional release
of the battery release latch.
1. Turn the computer’s power off.
2. Disconnect all cables connected to the computer.
3. Close the LCD display panel and turn the computer upside down.
4. Insert the battery pack (➀).
5. Secure the battery pack lock. Check the battery lock (➁) was changed
to the lock position ( ).
Battery pack
Battery lock
Figure 6-2 Securing the battery pack

TOSHIBA Password Utility

The TOSHIBA Password Utility provides two levels of password security:
User and Supervisor.
Passwords set in TOSHIBA Password Utility are different from the
Windows password.
User password
To start the utility, point to or click the following items:
start -> All Programs -> TOSHIBA -> Utilities ->Password Utility
■ Set (button)
Click this button to register a password of up to 50 characters. After a
password is set, you will be prompted to enter it when you start the
computer.
■ After you set the password, a dialog box will be displayed asking
whether you want to save it to a floppy disk or other media.
If you forget the password, you can open the password file on
another computer. Be sure to keep the media in a safe place.
■ When entering a password ensure that you use standard keyboard
characters and not characters entered as ASCII codes or characters
copied by using the copy-and-paste facility, as these will not be able to
be entered when the computer starts. In addition, you are advised to
ensure the registered password is correct by outputting it to a password
file.
■ Delete (button)
Click this button to delete a registered password. Before you can delete
a password, you must first enter the current password correctly.
■ Change (button)
Click this button to change a registered password. Before you can
change a password, you must first enter the current password correctly.
■ Owner String (text box)
You can use this box to associate text with the password. After you
enter text, click Apply or OK. When the computer is started, this text
will be displayed together with the prompt asking you to enter a
password.

Supervisor password
To set a supervisor password, follow the steps below.
1. Click start.
2. Click Run.
3. Enter the following: C:\Program Files\Toshiba\Windows
Utilities\SVPWTool\TOSPU.EXE
If you set a supervisor password, some functions might be restricted when
a user logs on with the user password.
This utility lets you do the following:

■ Register, delete or change the supervisor password.
■ Specify restrictions for general users.
Starting the computer by password

To start up the computer with the user password, follow these steps:
1. Turn on the power as described in Chapter 3, Getting Started. The
following message will appear in the LCD:
S Password =
At this point, the hotkeys Fn + F1 to F9 do not work. They will function after
you enter the password.
2. Enter the password.

3. Press Enter.
If you enter the password incorrectly three times in a row, the computer
shuts off. In this case, you must turn the computer back on to retry
password entry.
Power-up modes
The computer has the following power-up modes:
■ Boot: Computer shuts down without saving data. Always save your
work before you turn the computer off in boot mode.
■ Hibernation: Data in memory is saved to the hard disk.
■ Standby: Data is maintained in the computer’s memory.
Refer also to the sections Turning on the power and Turning off the power
in Chapter 3, Getting Started.
Windows utilities
You can specify the setting in TOSHIBA Power Saver.
Hot keys
You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter
Hibernation. Refer to Chapter 5, The Keyboard for details.

Panel power on/off

You can set up your computer so that power turns off automatically when
you close the computer’s LCD display panel. When you open the
computer’s LCD display panel, power turns on in Standby or Hibernation
mode but not in boot mode.
If the panel power off function is enabled and you manually shut down
Windows, do not close the computer’s LCD display panel until the shut
down process has been completed.
System Auto Off

This feature turns the system off automatically if it is not used for a set
duration. The system shuts down in Standby mode or Hibernation mode in
Windows.


libretto U100
Chapter 7
HW Setup
This chapter explains how to use TOSHIBA HW Setup program to

configure your computer. TOSHIBA HW Setup lets you configure settings
for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config
and USB.
Accessing HW Setup
To run HW Setup, click start, click Control Panel, click Printers and Other
Hardware and select TOSHIBA HWSetup.
HW Setup window
The HW Setup window contains the following tabs: General, Display,
Boot Priority, Keyboard, CPU, LAN, Device Config and USB.
There are also three buttons: OK, Cancel and Apply.
OK Accepts your changes and closes the HW Setup
window.
Cancel Closes the window without accepting your
changes.
Apply Accepts all your changes without closing the HW
Setup window.
General
This window displays the BIOS version and contains two buttons: Default
and About.
Default Return all HW Setup values to the factory
settings.
About Display the HW Setup version.
Setup
This field displays BIOS Version and date.
User’s Manual 7-1

HW Setup
Display
This tab lets you customize your computer’s display settings for either the
internal LCD screen or for an external monitor.
Power On Display
Lets you select the display to be used when the computer is booted.
(This setting is only available on Standard VGA mode and is not available
on Windows Desktop).
Auto-Selected Selects an external monitor if one is connected.
Otherwise, it selects the internal LCD (Default).
LCD + Analog RGB Selects both the internal LCD and external
monitor for simultaneous display.
If the connected external monitor does not support the computer's current
video mode, selecting the LCD + Analog RGB mode will not display any
image on the external monitor.
At Windows start-up, the screen is displayed on the external monitor if it
was connected at the time of the previous power-off, and is found at the
start-up. Otherwise, the screen is displayed on the internal LCD.
Boot Priority
Boot Priority Options
This option sets the priority for booting the computer. Select from the
following settings:
HDD −> FDD −> The computer looks for bootable files in the
CD-ROM −> LAN following order: HDD, floppy disk drive*1,
CD-ROM*2 and LAN (Default).
FDD −> HDD −> The computer looks for bootable files in the
CD-ROM −> LAN following order: floppy disk drive*1, HDD,
CD-ROM*2 and LAN.
HDD −> CD-ROM −> The computer looks for bootable files in the
LAN −> FDD following order: HDD, CD-ROM*2, LAN and
floppy disk drive*1.
FDD −> CD-ROM −> The computer looks for bootable files in the
LAN −> HDD following order: floppy disk drive*1, CD-ROM*2,
LAN and HDD.
CD-ROM −> LAN −> The computer looks for bootable files in the
HDD −> FDD following order: CD-ROM*2, LAN, HDD, floppy
disk drive*1.
CD-ROM −> LAN −> The computer looks for bootable files in the
FDD −> HDD following order: CD-ROM*2, LAN, floppy disk
drive*1 and HDD.
7-2 User’s Manual

HW Setup
You can override the settings and manually select a boot device by
pressing one of the following keys while the computer is booting:
U Selects the USB floppy disk drive.
N Selects the Network.
1 Selects the primary HDD.
C Selects the CD-ROM*2.
M Selects the USB Memory.
*1 The floppy disk drive will be used to start the notebook when there is a
bootable disk contained in the external drive. If SD memory is installed as
well, the external floppy disk drive will be checked first, followed by the SD
memory device itself.
*2 The optical media drive will be used to start the notebook when there is a
bootable disk contained in the drive.
To change the boot drive, follow the steps below.
1. Hold down F12 and boot the computer.
2. The following menu will be displayed with the following icons:
Built-in HDD, CD-ROM, FDD (or SD memory card), Network (LAN),
USB Memory boot.
A bar will appear only under the selected device.
User’s Manual 7-3

HW Setup
3. Use the left/right cursor keys to highlight the boot device you want and
press Enter.
■ If only a Supervisor Password has been set, the following should be
noted:
■ The boot device menu will appear when you use the user password
to start the computer and the ‘Able to run HW Setup’ option has
been configured.
■ The boot device menu will not appear when you use the user
password to start the computer and the ‘Unable to run HW Setup’
option has been configured.
■ If both a Supervisor Password and a User Password are set, the
following should be noted:
■ The boot device menu will appear when you use either the
Supervisor Password or the User Password to start the computer,
and the ‘Able to run HW Setup’ option has been configured.
■ The boot device menu will not appear when you use the User
Password to start the computer and the ‘Unable to run HW Setup’
option has been configured.
■ The boot device menu will appear when you use the Supervisor
Password to start the computer, even if the ‘Unable to run HW
Setup’ option has been configured.
■ The boot device selection methods described above will not change
the boot priority settings that have been configured in HW Setup. In
addition, if you press a key other than one of those listed, or if the
selected device is not installed, the system will continue to boot
according to the current and available settings in HW Setup.
Network Boot Protocol

This feature sets the protocol to remotely boot from the network.
[PXE] Sets PXE as the protocol (Default).
[RPL] Sets RPL as the protocol.
HDD Priority Options

Set the priority when the hard disk drive is used as the startup device.
Built-in HDD -> The priority is set as built-in HDD -> USB
USB (Default) memory.
USB -> Built-in The priority is set as USB memory -> built-in
HDD HDD.
7-4 User’s Manual

HW Setup
USB Memory BIOS Support Type

Set the type of the USB memory as a startup device.
HDD Set the type of the USB memory to be equivalent
to the HDD (Default).
* Based on the [HDD] order in the [Boot Priority
Options] item. The order with respect to the other
HDD can be set in the [HDD Priority Options]
item.
FDD Set the type of the USB memory to be equivalent
to the FDD.
* Based on the [FDD] order in the [Boot Priority
Options] item.
Keyboard
Wake-up on Keyboard
When this feature is enabled and the computer is in Standby mode,
you can turn on the computer by pressing any key. It is effective only for the
internal keyboard and only when the computer is in standby mode.
Enabled Enables the Wake-up on Keyboard function.
Disabled Disables the Wake-up on Keyboard function
(Default).
CPU
This function lets you set the CPU operating mode.
This option is displayed only for models with a Pentium-M® processor.
Dynamic CPU Frequency Mode

This option lets you choose from the following settings:
Dynamically CPU power consumption and clock speed
Switchable automatic switching function is enabled.
When the computer is in use, CPU operation is
automatically switched when necessary
(Default).
Always High CPU power consumption and clock speed
automatic switching function is disabled.
The CPU always runs at its fastest speed.
Always Low CPU power consumption and clock speed
automatic switching function is disabled.
The CPU always runs at low power consumption
and low speed.
User’s Manual 7-5

HW Setup
LAN
Wake-up on LAN
This feature lets the computer’s power be turned on when it receives a
wake-up signal from the LAN.
Enabled Enables Wake-up on LAN.
Disabled Disables Wake-up on LAN. (Default)
Do not install or remove an optional memory module while Wake-up on

LAN is enabled.
The Wake-up on LAN function consumes power even when the system is
off. Leave the AC adaptor connected while using this feature.
Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled Enables Built-in LAN functions (Default).
Disabled Disables Built-in LAN functions.
Device Config
Device Configuration
This option lets you set the device configuration.
All Devices BIOS sets all devices.
Setup by OS Operating system sets devices that it can control
(Default).
USB
USB KB/Mouse Legacy Emulation
Use this option to enable or disable USB KB/Mouse Legacy Emulation.
If your operating system does not support USB, you can still use a USB
mouse and keyboard by setting the USB KB/Mouse Legacy Emulation
item to Enabled.
Enabled Enables USB KB/Mouse Legacy Emulation
(Default).
Disabled Disables USB KB/Mouse Legacy Emulation.
7-6 User’s Manual

HW Setup
USB-FDD Legacy Emulation

Use this option to enable or disable the USB floppy diskette drive emulation
function.
Enabled Enables USB-FDD Legacy Emulation (Default).
Disabled Disables USB-FDD Legacy Emulation.
User’s Manual 7-7

HW Setup
7-8 User’s Manual

libretto U100
Chapter 8
Optional Devices
Optional devices can expand the computer’s capabilities and its versatility.
This chapter describes connection or installation of the following devices,
which are available from your TOSHIBA dealer:
Cards/memory
■ PC card
■ SD card
■ Memory expansion
Power devices
■ Battery pack
■ AC adaptor
Peripheral devices
■ USB floppy disk drive
■ External monitor
■ i.LINK (IEEE1394)
■ libretto DVD Dock
User’s Manual 8-1

Optional Devices
PC card
The computer is equipped with a PC card slot that can accommodate a
Type II card. Any PC card that meets industry standards (manufactured by
TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC
cards, including PC card 16’s multifunction card and CardBus PC cards.
CardBus supports the new standard of 32-bit PC cards. The bus provides
superior performance for the greater demands of multimedia data
transmission.
■ PC cards can sometimes become hot during PC operation. Before you
remove a PC card always wait for it to cool. You could get burned
removing a hot PC card.
■ Keep foreign objects out of the PC card slot. Never allow metal objects,
Inserting a PC card
The PC card slot is located on the left side of the computer.
Windows hot-install feature lets you insert PC cards while the computer’s
power is on.
Do not insert a PC card while the computer is in standby or hibernation
mode. Some cards might not work properly.
To insert a PC card, follow the steps below:
1. Slide the extended eject latch to pop the Dummy card out slightly.
2. Grasp the Dummy card and draw it out.
3. Insert a PC card in the PC card slot.
4. Press gently to ensure a firm connection.
PC card slot
PC card
Figure 8-1 Inserting the PC card
5. After inserting the PC card, refer to the PC card’s documentation and

check the configuration in Windows to make sure it is appropriate for
your PC card.
8-2 User’s Manual

Optional Devices
Removing a PC card
To remove the PC card, follow the steps below.
1. Open the Safely Remove Hardware icon on the Task Bar.
2. Point to PC card and click.
3. Slide the PC card eject latch to extend it.
If the PC card is not inserted all the way, the eject latch may not cause it to
pop out sufficiently to allows it to be grasped. Be sure to push the PC card
firmly into the computer and slide the eject latch again.
4. Grasp the PC card and draw it out.
PC card
PC card eject
latch
Figure 8-2 Removing the PC card
When you are not using a PC Card in the computer, please ensure the
Dummy Card is in place to protect the slot.
SD card
The computer is equipped with an SD card slot that can accommodate
Secure Digital flash memory cards with various memory capacities.
SD cards let you easily transfer data from devices, such as digital cameras
and Personal Digital Assistants, that use SD card flash-memory. The cards
have a high level of security and copy protection features. The slot cannot
accommodate Multi Media cards.
Keep foreign objects out of the SD card slot. Never allow metal objects,
SD memory cards comply with SDMI (Secure Digital Music Initiative),

which is a technology adopted to prevent unlawful copy or playback of
digital music. For this reason, you cannot copy or playback protected
material on another computer or other device. You may not use the
reproduction of any copyrighted material except for your personal
enjoyment.
User’s Manual 8-3

Optional Devices
Formatting an SD memory card

SD memory cards are sold already formatted in conformity to the SD
memory card standard. If you format the SD card again, be sure to format it
with the TOSHIBA SD memory card format utility and not with the standard
Windows format command.
In order to run TOSHIBA SD memory card format, click start, point to All
Programs, point to TOSHIBA, point to Utilities and click SD memory card
Format.
TOSHIBA SD memory card format does not format the protected area of
the SD memory card. If you need to format all areas of the SD memory
card, including the protected area, you should ensure you use an
application that fully supports the copy protection system.
Inserting an SD card
To insert an SD card, follow the steps below.
1. Insert an SD card in the SD card slot.
2. Press gently to ensure a firm connection.
SD card
SD card slot
Figure 8-3 Inserting an SD card
Make sure the SD card is oriented properly before you insert it.
8-4 User’s Manual

Optional Devices
Removing an SD card
To remove an SD card, follow the steps below.
2. Point to SD card and click.
3. Push in the SD card and release it to pop the card out slightly.
4. Grasp the SD card and remove it.
SD card
SD card slot
Figure 8-4 Removing an SD card
Do not remove an SD card while the computer is in Standby or Hibernation

mode. The computer could become unstable or data in the SD card could
be lost.
SD card care
Set the write-protect switch to the lock position, if you do not want to record
data.
1. Do not write to an SD card if the battery power is low. Low power could
affect writing accuracy.
2. Do not remove an SD card while read/write is in progress.
3. The SD card is designed so that it can be inserted only one way. Do not
try to force the SD card into the SD card slot.
4. Do not leave an SD card partially inserted in the slot. Press the SD card
until you hear it click into place.
5. Do not twist or bend SD cards.
6. Do not expose SD cards to liquids or store in humid areas or lay media
close to containers of liquid.
7. After using an SD card, return it to its case.
8. Do not touch the metal part or expose it to liquids or let it get dirty.
User’s Manual 8-5

Optional Devices
Creation of a boot disk

Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card
can be created if required. Refer to the Utilities of Chapter 1, Introduction
for details.
Memory expansion
This computer has a single memory module socket located on its underside
- depending on the standard memory configuration of your computer, this
socket may or may not be populated. You can increase the capacity of
RAM by installing additional an memory module or replacing the existing
module with one of a higher capacity.
■ Place a mat beneath the computer to prevent scratching or damaging
the computer's lid when installing/replacing the memory module. Avoid
any materials that generate static electricity.
■ When you remove a memory, please do not touch other portions of a
computer.
■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following
conditions. You can damage the computer and the module. Also, data
will be lost.
a. The computer is turned on.
b. The computer was shut down using either Standby mode or
Hibernation mode.
c. Wake-up on LAN is enabled.
■ Be careful not to let screws or other foreign matter fall into the
computer. It could cause malfunction or electric shock.
■ Expansion memory is a precision electronic component that may be
fatally damaged by static electricity. Since the human body can carry
static electricity, it is important that you discharge yourself before
touching or installing any expansion memory modules. To discharge
your body’s static electricity, simply touch any metal close to you with
bare hands.
Some memory modules can be physically installed but are not compatible
with the computer. In this case, the computer will issue a warning. When
you turn on the power, a series of short beeps will sound in the pattern of
one, three, three, one. Shut down the power and remove the incompatible
module.
Use a point size 0 Phillips screwdriver to remove and fasten the screws.
Use of an incorrect screwdriver can damage the screw heads.
8-6 User’s Manual

Optional Devices
Installing memory module

Follow the steps below to install a memory module.
1. Set the computer to boot mode and turn the computer’s power off.
Make sure the Power indicator is off. Refer to the Turning off the power
section in Chapter 3, Getting Started.
2. Remove AC adaptor and all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack. Refer to
Replacing the battery pack section in Chapter 6, Power and Power-Up
Modes, for details.
4. Loosen the screw securing the memory module cover. The screw is
attached to the cover to prevent it from being lost.
5. Slide your fingernail or a thin object under the cover and lift it off.
Memory module cover
Screw
Figure 8-5 Removing the memory module cover
6. Align the notch of the memory module with that of the memory slot,
gently insert the module into the slot at about a 45 degree angle and
push the module down until latches on either side snap into place.
Figure 8-6 Seating the memory module
User’s Manual 8-7

Optional Devices
Align the grooves of the memory module with the locking tabs of the
connector and insert the module into the connector firmly. If you find it
difficult to install the memory module, try to adjust the tabs of the connector
with a pen tip or other tools. Make sure to hold the memory module with
your fingers on the side edges (sides with grooves).
■ Be careful not to drop the screw inside the computer.

■ Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access
problems.
7. Seat the memory module cover and secure it with one screw.
Memory module cover
Screw
Figure 8-7 Seating the memory module cover
8. Install the battery pack. Refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, for details.
10. Turn the computer power on and make sure the added memory is
recognized.
Click start, click Control Panel, click Performance and Maintenance
and select the System icon. Open System Properties window and
click General tab.
Removing memory module

To remove the memory module, make sure the computer is in boot mode
then:
1. Set the computer to boot mode and turn the computer’s power off.
Make sure the Power indicator is off.
2. Remove AC adaptor and all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack. Refer to
Replacing the battery pack section in Chapter 6, Power and Power-Up
Modes, for details.
4. Loosen the screw securing the memory module cover. The screw is
attached to the cover to prevent it from being lost.
8-8 User’s Manual

Optional Devices
5. Slide your fingernail or a thin object under the cover and lift it off.
6. Push the latches to the outside to release the module. A spring will
force one end of the module up.
7. Grasp the module by the sides and pull it out.
■ If you use the computer for a long time, the memory modules and the
circuits located close to the memory modules will become hot. In this
case, let them cool to room temperature before you replace them.
■ Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access
problems.
Latches
Figure 8-8 Removing the memory module
8. Seat the memory module cover and secure it with one screw.
Be sure that the cover is closed firmly.
9. Install the battery pack. Refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, for details.
Battery pack
You can increase the portability of the computer with additional battery
packs. If you’re away from an AC power source and your battery runs low,
you can replace it with a freshly charged battery. Refer to Chapter 6, Power
and Power-Up Modes.
Universal AC adaptor
If you frequently transport the computer between different sites such as
your home and office, purchasing an AC adaptor for each location will
reduce the weight and bulk of your carrying load.
User’s Manual 8-9

Optional Devices

The USB floppy disk drive module can be connected to the USB port.
For details on connecting the USB floppy disk drive module, refer to
Chapter 4, Operating Basics.
External monitor
An external analog monitor can be connected to the Mini-RGB port on the
computer. The computer supports VGA and XGA video modes. To connect
a monitor, follow the steps below.
1. Turn the computer’s power off.
2. Connect the monitor cable to the Mini-RGB port.
Monitor cable
Mini-RGB port
Figure 8-9 Connecting the monitor cable to the Mini-RGB port
3. Turn the monitor’s power on.

4. Turn the computer’s power on.
When you turn on the power, the computer automatically recognizes the
monitor and determines whether it is color or monochrome.
However, the Windows Desktop appears on a display device that you used
last time to shut down your computer, if the display device exists when you
turn on the power.
To change the display settings, press Fn + F5. If you disconnect the
external monitor before you turn the computer’s power off, be sure to press
Fn + F5 to switch to the internal display. Refer to Chapter 5, The Keyboard,
for details on using hot keys to change the display setting.

Optional Devices
i.LINK (IEEE1394)
i.LINK (IEEE1394) is used for high-speed data transfer for a range of
compatible devices such as
■ Digital video cameras
■ Hard disk drives
■ MO drives
■ CD-RW drives
i.LINK uses a four-pin connector, which does not carry electric current.
External devices will need their own power supply.
Precautions
■ Make a back-up of your data before transferring it to the computer.
There is a possibility that the original data will be damaged. There is a
particular risk that some frames will be deleted in the case of digital
video transfer. TOSHIBA assumes no liability for such loss of data.
■ Do not transfer data in areas where static electricity is easily generated
or in areas subjected to electronic noise. Data can be destroyed.
■ If you are transferring data through an IEEE1394 hub, do not connect or
disconnect other devices from the hub during data transfer. There is a
likelihood that data will be damaged. Connect all devices to the hub
before you turn on the computer’s power.
■ You may not use any copyrighted video or music data copied from a
video camera except for your personal enjoyment.
■ If you connect/disconnect an i.LINK device to/from another i.LINK
device that is currently exchanging data with the computer, data frames
might be dropped.
■ Make sure data transfer has ended or turn off the computer, before you:
■ Connect/disconnect an i.LINK device to/from the computer.
■ Connect/disconnect an i.LINK device to/from another i.LINK device
that is connected to the computer.

Optional Devices
Connecting
1. Make sure the connectors are properly aligned and plug the i.LINK
(IEEE1394) cable into the computer.
i.LINK (IEEE1394)
connector
i.LINK (IEEE1394) port
Figure 8-10 Connecting the i.LINK(IEEE1394) cable into the computer
2. Plug the other end of the cable into the device.

Note the following when you use i.LINK:
■ You may need to install drivers for your i.LINK devices.
■ Not all i.LINK devices have been tested. Therefore, compatibility with all
i.LINK devices cannot be guaranteed.
■ Use i.LINK (IEEE1394) cable no longer than three meters.
■ Some devices might not support standby or automatic off functions.
■ Do not connect or disconnect an i.LINK device while it is using an
application or when the computer is automatically shutting it down to
save power. Data might be destroyed.
Disconnecting
2. Point to i.LINK (IEEE1394) device and click.
3. Disconnect the cable from the computer then from the i.LINK device.
Refer also to the documentation that came with your i.LINK device.

Optional Devices
libretto DVD Dock

The optical media drive can be used by connecting the libretto
DVD Dock to this computer. This will allow the computer to read
CD-ROMs/DVD-ROMs and/or write data to
CD-Rs/CD-RWs/DVD-Rs/DVD-RWs/DVD+Rs/DVD+RWs and DVD-RAM.
The full-size drive provides high-performance execution of
CD/ DVD-ROM-based programs. You can run either 12 cm (4.72") or
8 cm (3.15") CD/DVDs without an adaptor.
Please end all applications, including the Express Media Player, that may
be running before installing/removing the libretto DVD Dock.
Front and Left side

The following figure shows the libretto DVD Dock's front and left side.
Docking connector
Lock lever
Express Media
Player Buttons
Hold switch
Front latches Optical media drive
Figure 8-11 Front and life side the libretto DVD Dock
Lock lever Rotating this will lock the libretto DVD Dock to the
computer so that it cannot be removed.
Docking connector This is the computer interface. It connects
directly to the computer's docking port.
Express Media Five buttons are available for use: CD/DVD,
Player Buttons Play/Pause, Stop, Previous, Next. These buttons
allow you to manage Audio/Video, run
applications and access utilities.

Optional Devices
CD/DVD button Pressing this button will launch an application

program that allows you to listen to CDs or watch
DVDs.
Pressing this button in the power-off condition will
run Express Media Player. Once Express Media
Player is launched, the front operation panel will
become active. Pressing this button when
Express Media Player is running will do nothing
while. Pressing this button while the computer is
switched on or in Standby Mode will either launch
Windows Media Player or WinDVD.
Express Media Player is optional supported,
depending on the model purchased
Play/Pause button Press this button to run Windows Media Player/
WinDVD. If Windows Media Player or WinDVD is
already running, this button simply toggles
between Play and Pause functions.
STOP button Press this button to stop play.
Previous button Press this button to advance to the previous

track, chapter or data.
Next button Press this button to advance to the next track,

chapter or data.
Hold switch This switch will prevent unintended button

operations. Slide to the right to unlock the
button's functions and slide to the left to lock
(hold) them.
Front Latches Three latches at the front of the libretto DVD
Dock are used to locate it with the three holes
along the front part of the computer.
Optical media drive The libretto DVD Dock is configured with either a
DVD-ROM and CD-R/RW drive or a DVD Super
Multi drive.

Optional Devices
Right side and Back side

The following figure shows the libretto DVD Dock's right and back side.
Undock switch
Lock lever
Eject switch indicator
Figure 8-12 Right and back side the libretto DVD Dock
Lock lever Rotating this will lock the libretto DVD Dock
connected to the computer so that it cannot be
removed.
Undock switch Slide this switch to the left to eject the computer
from the DVD Dock.
Docking LED This indicator lights when the libretto DVD Dock
is connected to the computer. When the eject
operation is carried out, you should check that
this indicator is not lit before removing the
computer.
Connecting the libretto DVD Dock

Follow the steps below to connect the computer to the libretto DVD Dock.
Before you connect the libretto DVD Dock, make sure you turn off the
computer and disconnect the AC Adaptor and any other external devices.
1. Turn the computer's power off.

2. Disconnect all cables connected to the computer.
3. Place the computer on the libretto DVD Dock so that the Docking holes
of the front-side of the computer are aligned with the libretto DVD
Dock's Front Latches.

Optional Devices
4. Gently press the computer downward to connect the computer's

docking interface to the libretto DVD Dock's docking interface.
Docking holes
libretto DVD
Dock's front latch
Figure 8-13 Connecting the computer to the libretto DVD Dock.
5. Close the latches to secure the libretto DVD Dock to the computer.
Lock lever
Figure 8-14 Closing the latches
Disconnecting the libretto DVD Dock

Follow the steps below to disconnect the computer to the libretto DVD
Dock.
When removing the libretto DVD Dock, switch off the power to the main
computer unit before sliding the Eject Switch.
1. Save your work.

2. Turn the computer's power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.

Optional Devices
4. Close the LCD display panel and turn the computer (with the libretto
DVD Dock) upside down.
Lock lever
Figure 8-15 Opening the lock lever
5. Open the latches.

6. Lift off the libretto DVD Dock.
7. Turn the computer right side up.

Optional Devices

libretto U100
Chapter 9
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems

occur, following the procedures in this chapter can help to determine the
cause.
All readers should become familiar with this chapter. Knowing what might
go wrong can help prevent problems from occurring.
Problem solving process

Resolving problems will be much easier if you observe the following
guidelines:
■ Stop immediately when you recognize a problem exists. Further
action may result in data loss or damage. You may destroy valuable
problem-related information that can help solve the problem.
■ Observe what is happening. Write down what the system is doing and
what actions you performed immediately before the problem occurred.
If you have a printer attached, print a copy of the screen using PrtSc.
The questions and procedures offered in this chapter are meant as a guide,
they are not definitive problem solving techniques. Many problems can be
solved simply, but a few may require help from your dealer. If you find you
need to consult your dealer or others, be prepared to describe the problem
in as much detail as possible.
User’s Manual 9-1

Troubleshooting
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to
fix and yet can cause what appears to be a serious problem.
■ Make sure you turn on all peripheral devices before you turn on the
computer. This includes your printer and any other external device you
are using.
■ Before you attach an external device, turn the computer off. When you
turn the computer back on it recognizes the new device.
■ Make sure all options are set properly in the setup program.
■ Check all cables. Are they correctly and firmly attached? Loose cables
can cause signal errors.
■ Inspect all connecting cables for loose wires and all connectors for
loose pins.
■ Check that your floppy disk or CD/DVD-ROM is correctly inserted and
that the floppy disk’s write protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log.
This will help you describe your problems to your dealer. If a problem
recurs, the log will help you identify the problem faster.
Analyzing the problem

Sometimes the system gives clues that can help you identify why it is
malfunctioning. Keep the following questions in mind:
■ Which part of the system is not operating properly: keyboard, floppy
disk drives, hard disk drive, optical media drive, display. Each device
produces different symptoms.
■ Is the operating system configuration set properly? Check the
configuration options.
■ What appears on the display screen? Does it display any messages or
random characters? If you have a printer attached, print a copy of the
screen using PrtSc. Look up the messages in the software and
operating system documentation. Check that all connecting cables are
correctly and firmly attached. Loose cables can cause erroneous or
intermittent signals.
■ Do any indicators light? Which ones? What color are they? Do they stay
on or blink? Write down what you see.
■ Do you hear any beeps? How many? Are they long or short? Are they
high pitched or low? Is the computer making any unusual noises? Write
down what you hear.
Record your observations so you can describe them to your dealer.
9-2 User’s Manual

Troubleshooting
Software The problems may be caused by your software or disk. If

you cannot load a software package, the media may be
damaged or the program might be corrupted. Try loading
another copy of the software.
If an error message appears while you are using a software
package, check the software documentation. These
documents usually include a problem solving section or a
summary of error messages.
Next, check any error messages in the operating system
documentation.
Hardware If you cannot find a software problem, check your
hardware. First run through the items in the preliminary
checklist above. If you still cannot correct the problem,
try to identify the source. The next section provides
checklists for individual components and peripherals.
Before using a peripheral device or application software that is not an

authorized Toshiba part or product, make sure the device or software can
be used with your PC. Use of incompatible devices may cause injury or
may damage your PC.
Hardware and system checklist

This section discusses problems caused by your computer’s hardware or
attached peripherals. Basic problems may occur in the following areas:
■ System start-up ■ Pointing device
■ Self test ■ USB
■ Power ■ Fingerprint Sensor
■ Password ■ Memory expansion
■ Keyboard ■ Sound system
■ Internal LCD display panel ■ External monitor
■ Hard disk drive ■ i.LINK (IEEE1394)
■ DVD-ROM and CD-R/RW drive ■ Modem
■ DVD Super Multi drive ■ LAN
■ USB floppy disk drive ■ Wireless LAN
■ SD card ■ Bluetooth
■ PC card
System start-up
When the computer does not start properly, check the following items:
■ Self Test
■ Power Sources
■ Power-on Password
User’s Manual 9-3

Troubleshooting
Self test
When the computer starts up, the self test will be run automatically,
and the following will be displayed:
S In Touch with Tomorrow

TOSHIBA
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating
system, depending on how the Boot Priority is set in the TOSHIBA HW
Setup program.
If any of the following conditions are present, the self test failed:
■ The computer stops and does not proceed to display information or
messages except the TOSHIBA logo.
■ Random characters appear on the screen, and the system does not
function normally.
■ The screen displays an error message.
Turn off the computer and check all cable connections. If the test fails
again, contact your dealer.
Power
When the computer is not plugged into an AC outlet, the battery pack is the
primary power source. However, your computer has a number of other
power resources, including an intelligent power supply and Real Time
Clock battery. These resources are interrelated and any one could affect
apparent power problems. This section provides checklists for AC power
and the battery. If you cannot resolve a problem after following them, the
cause could lie with another power resource. In such a case, contact your
dealer.
9-4 User’s Manual

Troubleshooting
Overheating power down

If the computer’s internal temperature becomes too high, the computer will
automatically enter Hibernation or Standby mode and shut down.
Problem Procedure
Computer shuts down Leave the computer off until the DC IN indicator
and DC IN indicator stops blinking.
blinks orange
It is recommended to leave the computer off until the its interior reaches
room temperature even though the DC IN indicator stops blinking.
If the computer has reached room temperature

and still does not start, or if it starts but shuts
down quickly contact your dealer.
Computer shuts down Indicates a problem with the heat dispersal
and its DC IN indicator system. Please contact your dealer.
is flashing green
AC power
If you have trouble turning on the computer with the AC adaptor connected,
check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes
for more information.
Problem Procedure
AC adaptor doesn’t Check the connections. Make sure the cord is
power the computer firmly connected to the computer and a power
(DC IN indicator does outlet.
not glow green)
Check the condition of the cord and terminals.
If the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the AC adaptor still does not power the
computer, contact your dealer.
User’s Manual 9-5

Troubleshooting
Battery
If you suspect a problem with the battery, check the DC IN indicator as well
as the Battery indicator. For information on indicators and battery
operation see Chapter 6, Power and Power-Up Modes.
Problem Procedure
Battery doesn’t power The battery may be discharged. Connect the AC
the computer adaptor to charge the battery.
Battery doesn’t charge If the battery is completely discharged, it will not
when the AC adaptor begin charging immediately. Wait a few minutes.
is attached (Battery If the battery still does not charge, make sure the
indicator does not outlet of the AC adaptor is supplying power.
glow in orange.)
Test it by plugging in an appliance.
Check whether the battery is hot or cold to the
touch. If the battery is too hot or too cold, it will
not charge properly. Let it reach room
temperature.
Unplug the AC adaptor and remove the battery to
make sure the terminals are clean. If necessary
wipe them with a soft dry cloth dipped in alcohol.
Connect the AC adaptor and replace the battery.
Make sure it is securely seated.
Check the Battery indicator. If it does not glow,
let the computer charge the battery for at least
20 minutes. If the Battery indicator glows after
20 minutes, let the battery continue to charge at
least another 20 minutes before turning on the
computer.
If the indicator still does not glow, the battery may
be at the end of its operating life. Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn’t power If you frequently recharge a partially charged
the computer as long battery, the battery might not charge to its full
as expected potential. Fully discharge the battery, then try to
charge it again.
Check the power consumption settings in
TOSHIBA Power Saver utility. Consider using a
power saving mode.
9-6 User’s Manual

Troubleshooting
Real Time Clock
Problem Procedure
The following The charge in the RTC battery has run out -
message is Displayed you will need to set the date and time in the BIOS
on the LCD screen: setup using the following steps:
RTC battery is 1. Press F1 key. BIOS setup will boot up.
low or CMOS 2. Set the date in System Date.
checksum is
inconsistent. 3. Set the time in System Time.
Press [F1] key to 4. Press End key. Confirmation message will
set Date/Time. appear.
5. Press Y key. BIOS setup will terminate and
the computer will be rebooted.
Password
Problem Procedure
Cannot enter Refer to the TOSHIBA Password Utility section in
password Chapter 6, Power and Power-Up Modes.
Keyboard
Keyboard problems can be caused by your setup configuration. For more
information refer to Chapter 5, The Keyboard.
Problem Procedure
Some letter keys Check that the numeric keypad overlay is not
produce numbers selected. Press Fn + F10 and try typing again.
Output to screen is Make sure the software you are using is not
garbled remapping the keyboard. Remapping involves
reassigning the meaning of each key. See your
software’s documentation.
If you are still unable to use the keyboard,
consult your dealer.
User’s Manual 9-7

Troubleshooting
Internal LCD display panel

Apparent LCD problems may be related to the computer’s setup. Refer to
Chapter 7, HW Setup, for more information.
Problem Procedure
No display Press hotkeys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
Markings appear on the These marks may have come from contact
LCD screen. between the screen and either the keyboard or
AccuPoint. Wipe the screen gently with a clean
dry cloth, if the markings remain, use LCD screen
cleaner but be sure to let the LCD screen dry
before closing it.
Problems above Refer to your software’s documentation to
remain unresolved or determine if the software is causing the difficulty.
other problems occur Run the diagnostic test.
Contact your dealer if the problems continue.
Hard disk drive
Problem Procedure
Computer does not Check if a floppy disk is in the floppy disk drive or
boot from hard disk a CD-ROM is in the optical media drive. Remove
drive any floppy disk and/or CD-ROM and check Boot
priority. Refer to the Boot Priority section in
Chapter 7, HW Setup.
There may be a problem with your operating
system files. Refer to your operating system
documentation.
Slow performance Your files may be fragmented. Run Disk
Defragmenter to check the condition of your files
and disk. Refer to your operating system
documentation or online HELP for information on
running the Disk Defragmenter.
As a last resort, reformat the hard disk. Then,
reload the operating system and other files.
If problems persist, contact your dealer.
9-8 User’s Manual

Troubleshooting
DVD-ROM and CD-R/RW drive

For more information, refer to Chapter 4, Operating Basics.
Problem Procedure
You cannot access a Make sure the drive’s disc tray is securely
CD/DVD in the drive closed. Press gently until it clicks into place.
Check whether the drive power is on. If the
power is off, click on the optical media drive
icon in the task tray and turn on the power.
Open the disc tray and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the disc tray could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is,
wipe it with a clean cloth dipped in water or a
neutral cleaner. Refer to the Media care section
in Chapter 4 for details on cleaning.
Some CD/DVDs run The software or hardware configuration may be
correctly, but others do causing a problem. Make sure the hardware
not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using.
The drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM: CD-DA, CD-Text, Photo CDTM
(single/multi-session),
CD-ROM Mode 1, Mode 2,
CD-ROM XA Mode 2 (Form1,
Form2), Enhanced CD
(CD-EXTRA), Addressing
Method 2
Recordable CD: CD-R, CD-RW
Check the region code on the DVD. It must
match that on the DVD-ROM and CD-R/RW
drive. Region codes are listed in the Optical
media drives section in Chapter 2, The Grand
Tour.
User’s Manual 9-9

Troubleshooting
Problem Procedure
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA.
■ Do not use the mouse or keyboard during
writing.
■ Use only the software supplied with the
computer for recording.
■ Do not run or start other software during
writing.
■ Do not jar the computer during writing.
■ Do not connect/disconnect external devices
or install/remove internal cards during writing.
DVD Super Multi drive

Problem Procedure
You cannot access Make sure the drive’s disc tray is securely
a CD/DVD in the drive closed.
Press gently until it clicks into place.
Check whether the drive power is on. If the
power is off, click on the optical media drive icon
in the task tray and turn on the power.
Open the disc tray and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the disc tray could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaner. Refer to the Media care section in
Chapter 4 for details on cleaning.

Troubleshooting
Some CD/DVDs run The software or hardware configuration may be

correctly, but others do causing a problem. Make sure the hardware
not configuration matches your software’s needs.
Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using.
The drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM: CD-DA, CD-Text, Photo CDTM
(single/multi-session), CD-ROM
Mode 1, Mode 2, CD-ROM XA
Mode 2 (Form1, Form2), Enhanced
CD (CD-EXTRA), Addressing
Method 2
Check the region code on the DVD. It must
match that on the DVD Super Multi drive. Region
codes are listed in the Optical media drives
section in Chapter 2, The Grand Tour.

Problem Procedure
Drive does not operate There may be a faulty cable connection. Check
the connection to the computer and to the drive.
Some programs run The software or hardware configuration may be
correctly but others do causing a problem. Make sure the hardware
not configuration matches your software needs.
You cannot access the Try another floppy disk. If you can access the
external 3 1/2" floppy floppy disk, the original floppy disk (not the drive)
disk drive is probably causing the problem.

Troubleshooting
SD card
Refer also to Chapter 8, Optional Devices.
Problem Procedure
SD card error occurs Reseat the SD card to make sure it is firmly
connected.
Check the card’s documentation.
You cannot write to an Make sure the card is not write protected.
SD memory card
You cannot read a file Make sure the target file is on the SD memory
card inserted in the slot.
PC card
Refer also to Chapter 8, Optional Devices.
Problem Procedure
PC card error occurs Reseat the PC card to make sure it is firmly
connected.
Make sure the connection between the external
device and the card is firm.
Check the card’s documentation.

Pointing Device
If you are using a USB mouse, also refer to the USB section in this chapter
and to your mouse documentation.
AccuPoint
Problem Procedure
The AccuPoint does Check the device settings. Click start, click
not work Control Panel, click Printers and Other
Hardware and select the Mouse icon. Open the
Mouse Properties and click the Dual Pointing
Device tab. Then click the Detail Setting button
and click the Device Select tab.
On-screen pointer The system might be busy. If the pointer is
does not respond to shaped as an hourglass, wait for it to resume its
Accupoint operation normal shape and try again to move it.

Troubleshooting
Problem Procedure
The mouse pointer Try changing the speed setting in the mouse
moves too fast or too control utility.
slow 1. Click start, click Control Panel, click
Printers and Other Hardware and select
Mouse icon.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
Double-clicking Try changing the double-click speed setting in
(AccuPoint control the mouse control utility.
buttons) does not work 1. Click start, click Control Panel, click
Mouse icon.
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
Fingerprint Sensor
Problem Procedure
Reading of the Please try again using the correct posture.
fingerprint was not Refer to Using the Fingerprint Sensor in Chapter
successful. 4, Operating Basics.
Try the recognition process again using another
enrolled finger.
The fingerprint cannot Try the recognition process again using another
be read due to injuries enrolled finger.
to the finger. If fingerprints from all the enrolled fingers cannot
be read, you should logon by using the keyboard
to temporarily enter the password.

Troubleshooting
USB mouse
Problem Procedure
On-screen pointer The system might be busy. If the pointer is
does not respond to shaped as an hourglass, wait for it to resume its
mouse operation normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
Double-clicking does Try changing the double-click speed setting in
not work the mouse control utility.
1. Click start, click Control Panel, click
Mouse icon.
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
The mouse pointer Try changing the speed setting in the mouse
moves too fast or too control utility.
slow 1. Click start, click Control Panel, click
Mouse icon.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
The mouse pointer The mouse might be dirty. Refer to your mouse
moves erratically documentation for instructions on cleaning.

Troubleshooting
USB
Refer also to your USB device’s documentation.
Problem Procedure
USB device does not Check for a firm cable connection between the
work USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows XP
documentation for information on checking the
drivers.
If you are using an operating system that does
not support USB, you can still use a USB mouse
and/or USB keyboard. If these devices do not
work, make sure the USB KB/Mouse Legacy
Emulation item in HW Setup is set to Enabled.
Memory expansion
Refer also to Chapter 8, Optional Devices, for information on installing
memory modules.
Problem Procedure
Beep sounds. Make sure the memory module installed in the
(Two beeps, a dash memory slot is compatible with the computer.
and a dot, for a If an incompatible module has been installed,
defective memory follow the steps below.
module in slot.) 1. Turn off the computer.
2. Disconnect the AC adaptor and all peripheral
devices.
3. Remove the battery pack.
4. Remove the memory module.
5. Install the battery and/or connect the AC
adaptor.
6. Turn on the power.

Troubleshooting
Sound System
Refer also to documentation for your audio devices.
Problem Procedure
No sound is heard Adjust the volume control dial.
Check the software volume settings.
Make sure the headphone connection is secure.
Check Windows Device Manager. Make sure the
sound function is enabled and that settings for
I/O address, Interrupt level and DMA are correct
for your software and do not conflict with other
hardware devices that you may have connected
to the computer.
External monitor
Refer also to Chapter 8, Optional Devices, and to your monitor’s
documentation.
Problem Procedure
Monitor does not turn Make sure that the external monitor’s power
on switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
No display Try adjusting the contrast and brightness controls
on the external monitor.
Press hot keys Fn + F5 to change the display
priority and make sure it is not set for the internal
LCD.
Display error occurs Check that the cable connecting the external
monitor to the computer is attached firmly.

Troubleshooting
i.LINK (IEEE1394)
Problem Procedure
i.LINK device does not Make sure the cable is securely connected to the
function computer and to the device.
Make sure the device’s power is turned on.
Reinstall the drivers. Open the Windows
Control Panel and double-click the Add
Hardware icon. Follow the on-screen
directions.
Restart Windows.
Modem
Refer to Appendix C, AT Commands and Appendix D, S-registers.
Problem Procedure
Communication Make sure the computer’s internal modem
software can’t initialize settings are correct. Refer to Phone and Modem
modem Properties in the Control Panel.
You can hear a dial If the call is going through a PBX machine, make
tone but can’t make a sure the communication application’s tone dial
call detection feature is disabled.
You can also use the ATX command. Refer to
Appendix C, AT Commands.
You place a call, but a Make sure the settings are correct in your
connection can’t be communications application.
made
After making a call you Make sure the tone or pulse selection in your
can’t hear a ring communications application is set correctly.
You can also use the ATD command. Refer to
Appendix C, AT Commands.
Communication is cut The computer will automatically cut off
off unexpectedly communication when connection with the carrier
is not successful for a set time interval.
Try lengthening this time interval.
A CONNECT display is Check the error control setting in your
quickly replaced by NO communications application.
CARRIER You can also use the AT\N command.
Refer to Appendix C, AT Commands.

Troubleshooting
Problem Procedure
Character display In data transmission, make sure the parity bit and
becomes garbled stop bit settings correspond with those of the
during a remote computer.
communication Check the flow control and communication
session protocol.
You cannot receive an Check the rings before auto answer setting in
incoming call your communications application.
You can also use the ATS0 command. Refer to
Appendix D, S-registers.
LAN
Problem Procedure
Cannot access LAN Check for a firm cable connection between the
LAN jack and the LAN hub.
Wake-up on LAN does Make sure the AC adaptor is connected. The
not work Wake-up on LAN function consumes power even
when the system is off.
If problems persist, consult your LAN
administrator.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN
administrator. For more information on wireless communication, refer to
Chapter 4, Operating Basics.
Problem Procedure
Cannot access Make sure the computer’s wireless
Wireless LAN communication switch is set to on.
If problems persist, contact your LAN
administrator.

Troubleshooting
Bluetooth
For more information on wireless communication, refer to Chapter 4,
Operating Basics.
Problem Procedure
Cannot access Make sure the computer’s wireless

Bluetooth device communication switch is set to on.
Make sure the Bluetooth Manager is running and

the power to the Bluetooth device is turned on.
Make sure no optional Bluetooth PC card or

Bluetooth SD card are installed in the computer -
the built-in Bluetooth function and an optional
Bluetooth PC card cannot operate
simultaneously. If problems persist, contact your
dealer.
Disposing of PC and PC batteries

■ Discard this PC in accordance with ordinances or rules of local
regulations. For further information, contact your local government.
■ This PC contains rechargeable batteries. After repeated use, the
batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.
■ Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old batteries
or how to dispose of them properly. This product contains mercury.
Disposal of this material may be regulated due to environmental
considerations. For disposal, reuse or recycling information, please
contact your local government.
■ If your hard disk or other storage media contains sensitive data, you
should be aware that standard deletion procedures do not remove data
from the media. These standard deletion procedures include:
■ Selecting Delete for a target file
■ Putting files in the Recycle Bin and emptying the Recycle Bin
■ Reformatting the media
■ Reinstalling an operating system from the recovery CD-ROM
The procedures above delete only the initial part of the data used for file
management. This makes the file invisible to the operating system, but
the data can still be read by specialized utilities. If you dispose of the
PC, please delete all the data on its hard disk drive. Doing so prevents
unauthorized use of such data. To ensure your data is not used for
unauthorized purposes, you can:
■ Physically destroy the HDD

Troubleshooting
■ Use a proven specialized utility to overwrite all data

■ Take the hard disk drive to a professional deletion service
All data deletion costs will be borne by you.
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for
additional technical assistance.
Before you call

Some problems you experience may be related to software or the operating
system, it is important to investigate other sources of assistance first.
Before contacting TOSHIBA, try the following:
■ Review troubleshooting sections in the documentation for software and
peripheral devices.
■ If a problem occurs when you are running software applications, consult
the software documentation for troubleshooting suggestions. Call the
software company’s technical support for assistance.
■ Consult the dealer you purchased your computer and/or software from.
They are your best sources for current information and support.
Where to write
If you are still unable to solve the problem and suspect that it is hardware
related, write to TOSHIBA at the location listed in the accompanying
warranty booklet or visit www.toshiba-europe.com on the Internet.

libretto U100
Chapter 10
Disclaimers
This chapter states the Disclaimers information applicable to TOSHIBA

computers. In the text in this manual, *XX is used to show which Disclaimer
description is related to TOSHIBA computers.
Descriptions related to this computer are marked with a blue *XX in this
manual. Clicking on *XX will display the related description.
LCD*1
Over a period of time, and depending on the usage of the computer, the
brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode.
Screen will dim when the computer is operated on battery power and you
will not be able to increase the brightness of the screen.
CPU*2
Central Processing Unit (“CPU”) Performance Disclaimer.
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use of battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of computer in areas with low air pressure (high altitude >
1,000 meters or > 3,280 feet above sea level)

Disclaimers
■ use of computer at temperatures outside the range of 5°C to 30°C

(41°F to 86°F) or > 25°C (77°F) at high altitude (all temperature
references are approximate and may vary depending on the specific
computer model - please refer to your PC documentation or visit the
Toshiba website at www.pcsupport.toshiba.com for details).
CPU performance may also vary from specifications due to design
configuration.
Under some conditions, your computer product may automatically
shut-down. This is a normal protective feature designed to reduce the risk
of lost data or damage to the product when used outside recommended
conditions. To avoid risk of lost data, always make back-up copies of data
by periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions under “Environmental Conditions”
in your PC documentation. Contact Toshiba technical service and support,
refer to TOSHIBA support section in Chapter 9 Troubleshooting for more
information.
Copy Protection*3
Copy protection technology included in certain media may prevent or limit
recording or viewing of the media.
HDD Drive Capacity*4

1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes using
powers of 10. The computer operating system, however, reports storage
capacity using powers of 2 for the definition of
1 GB = 1024 × 1024 × 1024 = 1,073,741,824 bytes, and therefore may
show less storage capacity. Available storage capacity will also be less if
the product includes one or more pre-installed operating systems, such as
Microsoft Operating System and/or pre-installed software applications, or
media content. Actual formatted capacity may vary.
Non-applicable Icons*5
Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.

Disclaimers
Wireless LAN/Atheros*6
The transmission speed over the wireless LAN and the distance over which
wireless LAN can reach may vary depending on surrounding
[54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g)
standard.] The actual transmission speed will be lower than the theoretical
maximum speed.
To use the Atheros Super AGTM or Super GTM function, your client and
access point must support the corresponding feature. Performance of
these functions may vary depending on the format of data transmitted.
SRS*7
SRS audio enhancements are available in the Microsoft Windows
operating system only.
Images*8
All images are simulated for purposes of illustration.
Express Media Player*9

The Express Media Player is not a Windows based application.
When using the QosmioTM Player, the Audio/Video recording feature will
not function.
The Express Media Player is not a Windows based application. Battery life
will be less than when using similar applications in the Windows Operating
System.
LCD Brightness and Eye Stain*10

Your LCD display has a brightness approaching that of a TV device. We
recommend that you adjust the brightness of your LCD to a comfortable
level to prevent possible strain on your eyes.
Graphics Processor Unit (“GPU”)*11

Graphics processor unit (“GPU”) performance may vary depending on
product model, design configuration, applications, power management
settings and features utilized. GPU performance is only optimized when
operating in AC power mode and may decrease considerably when
operating in battery power mode.

Disclaimers
General Main Memory Disclaimer*12

The graphics system in your computer may use part of the main system
memory for graphics performance and therefore reduce the amount of
system memory available for other computing activities. The amount of
system memory allocated to support graphics may vary depending on the
graphics system, applications utilized, system memory size and other
factors.
Battery Life Disclaimer*13

Battery life may vary considerably depending on product model,
configuration, applications, power management settings and features
utilized, as well as the natural performance variations produced by the
design of individual components. Published battery life numbers are
achieved on select models and configurations tested by Toshiba at the time
of publication. Recharge time varies depending on usage. Battery may not
charge while computer is consuming full power. After a period of time, the
battery will lose its ability to perform at maximum capacity and will need to
be replaced. This is normal for all batteries. To purchase a new battery
pack, see the accessories information that shipped with your computer.

libretto U100
Appendix A
Specifications
This appendix summarizes the computer’s technical specifications.
Physical Dimensions
Weight libretto U100
(typical) ■ 980 grams, configured with: Dothan ULV 1.1GHz,
256MB RAM, 7.2"WXGA, 1.8" 30GB (4200rpm),
W-LAN (Atheros-11g), no BT, 6cell battery pack.
■ 1.02 kilograms, configured with: Dothan ULV 1.2GHz,
1GB RAM, 7.2"WXGA, 1.8" 60GB (4200rpm), W-LAN
(Atheros-11g), BT V2.0+EDR, 6cell battery pack.
libretto DVD Dock
■ 450 grams
Weight will vary with other configurations. Above weights are
measured at a specific criteria. They are not guaranteed as the
maximum weight of the actual product.
Size libretto U100
■ 210 (w) x 165 (d) x 29.8/33.4 (h) millimeters (not including
parts that extend beyond the main body).
libretto DVD Dock
■ 211 (w) x 158 (d) x (Front) 20.9 / (Back) 14.3 (h) millimeters
(A height size excludes the rubber legs, the latches, etc).
User’s Manual A-1

Specifications
Environmental Requirements
Conditions Ambient temperature Relative humidity

Operating 5°C (41°F) to 35°C (95°F) 20% to 80%
Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 95%
Thermal Gradient 20°C per hour maximum
Wet-bulb 26°C maximum
temperature
Conditions Altitude (from sea level)
Operating -60 to 3,000 meters
Non-operating -60 to 10,000 meters
maximum
Power Requirements
AC adaptor 100-240 volts AC

50 or 60 hertz (cycles per second)
Computer 15 VDC
3.0 amperes
Built-in Modem
Network control unit (NCU)

Type of NCU AA
Type of line Telephone line (analog only)
Type of dialing Pulse
Tone
Control command AT commands
EIA-578 commands
Monitor function Computer’s speaker
Communication specifications
Communication Data: Full duplex
system Fax: Half duplex
A-2 User’s Manual

Specifications
Network control unit (NCU)

Communication Data
protocol ITU-T-Rec V.21/V.22/V.22bis/V.32
(Former CCITT) /V.32bis/V.34/V.90
Bell 103/212A
Fax
ITU-T-Rec V.17/V.29/V.27ter
(Former CCITT) /V.21 ch2
Communication Data transmission and reception
speed 300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600 bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/
37333/38666/40000/41333/42666/44000/45333/
46666/48000/49333/50666/52000/53333/54666/
56000 bps
Fax
2400/4800/7200/9600/12000/14400 bps
Transmitting level -10 dBm

Receiving level -10 to -40 dBm
Input/output 600 ohms ±30%
impedance
Error correcting MNP class 4 and ITU-T V.42
Data compression MNP class 5 and ITU-T V.42bis
Power supply +3.3V (supplied by computer)
User’s Manual A-3

Specifications
A-4 User’s Manual

libretto U100
Appendix B
Display Controller and Modes
Display controller
The display controller interprets software commands into hardware
commands that turn particular pels on or off.
The display controller supports VGA, SVGA and XGA modes at internal
LCD display panel.
A high-resolution external monitor connected to the computer can display
up to 2048 horizontal and 1536 vertical pixels at up to 64K mode.
The display controller also controls the video mode, which uses industry
standard rules to govern the screen resolution and the maximum number of
colors that can be displayed on screen.
Software written for a given video mode will run on any computer that
supports the mode.
The computer’s display controller supports all VGA and Super VGA modes,
the most widely used industry standards.
Video modes
The computer supports video modes defined in the tables below. If your
application offers a selection of mode numbers that do not match the
numbers on the table, select a mode based on mode type, resolution,
character matrix, number of colors and refresh rates. Also, if your software
supports both graphics and text modes, the screen display may appear to
operate faster using a text mode.
User’s Manual B-1

Table1 Video modes (VGA)
Video Type Resolution Character Colors Scanning

mode matrix (pels) frequency
Vertical (Hz)
0, 1 VGA 40 × 25 8×8 16 of 256K 70

Text Characters
2, 3 VGA 80 × 25 8×8 16 of 256K 70

Text Characters
0*, 1* VGA 40 × 25 8 × 14 16 of 256K 70

Text Characters
2*, 3* VGA 80 × 25 8 × 14 16 of 256K 70

Text Characters
0+, 1+ VGA 40 × 25 9 × 16 16 of 256K 70

Text Characters
2+, 3+ VGA 80 × 25 9 × 16 16 of 256K 70

Text Characters
4, 5 VGA 320 × 200 8×8 4 of 256K 70

Grph Pels
6 VGA 640 × 200 8×8 2 of 256K 70

Grph Pels
7 VGA 80 × 25 9 × 14 Mono 70
Text Characters
7+ VGA 80 × 25 9 × 16 Mono 70
Text Characters
B-2 User’s Manual

Table1 Video modes (VGA) continued
Video Type Resolution Character Colors Scanning

mode matrix frequency
(pels) Vertical (Hz)
D VGA 320 × 200 8×8 16 of 256K 70

Grph Pels
E VGA 640 × 200 8×8 16 of 256K 70

Grph Pels
F VGA 640 × 350 8 × 14 Mono 70

Grph Pels
10 VGA 640 × 350 8 × 14 16 of 256K 70

Grph Pels
11 VGA 640 × 480 8 × 16 2 of 256K 60

Grph Pels
12 VGA 640 × 480 8 × 16 16 of 256K 60

Grph Pels
13 VGA 320 × 200 8×8 256 of 256K 70

Grph Pels
User’s Manual B-3

Table 2 Video modes
Resolution LCD colors CRT colors Vertical

frequency (Hz)
640 × 480 256/256K 256/256K 60

75
85
100
800 × 600 256/256K 256/256K 60

75
85
100
1024 × 768 256/256K 256/256K 60

75
85
100
1280 × 1024 256/256K 256/256K 60

(Virtual) 75
85
100
1400 × 1050 256/256K 256/256K 60

(Virtual) 75
85
1600 × 1200 256/256K 256/256K 60

(Virtual) 75
85
100
1920 × 1440 256/256K 256/256K 60

(Virtual) 75
85
2048 × 1536 256/256K 256/256K 60

(Virtual) 75
* Resolution is support of only CRT 1024 × 768 or more.

Only External Monitor can perform change of Vertical frequency (Hz).
The screen may not be displayed properly in high resolution mode while
running 3D applications, during DVD playback, etc. Reduce the resolution
until the screen is displayed properly in such cases.
B-4 User’s Manual

Table 2 Video modes continued
Resolution LCD colors CRT colors Vertical frequency

(Hz)
640 × 480 64K/64K 64K/64K 60

75
85
100
800 × 600 64K/64K 64K/64K 60

75
85
100
1024 × 768 64K/64K 64K/64K 60

75
85
100
1280 × 1024 64K/64K 64K/64K 60

(Virtual) 75
85
100
1400 × 1050 64K/64K 64K/64K 60

(Virtual) 75
85
1600 × 1200 64K/64K 64K/64K 60

(Virtual) 75
85
100
1920 × 1440 64K/64K 64K/64K 60

(Virtual) 75
85
2048 × 1536 64K/64K 64K/64K 60

(Virtual) 75

User’s Manual B-5

Table 2 Video modes continued
Resolution LCD colors CRT colors Vertical

frequency (Hz)
640 × 480 16M/16M 16M/16M 60

75
85
100
800 × 600 16M/16M 16M/16M 60

75
85
100
1024 × 768 16M/16M 16M/16M 60

75
85
100
1280 × 1024 16M/16M 16M/16M 60

(Virtual) 75
85
100
1400 × 1050 16M/16M 16M/16M 60

(Virtual) 75
85
1600 × 1200 16M/16M 16M/16M 60

(Virtual) 75
85

B-6 User’s Manual

Display settings
1. You cannot move from the [Settings] tab of [Display Properties] to the
multi-monitor when you are using the display of the computer and an
external CRT display or a TV at the same time.
*The [Settings] tab is displayed in the following steps;
1) Open [Control Panel], click [Appearance and Themes].
2) Click [display].
3) Select [Settings] tab.
Figure B-1 Display Properties (1)
■ The way to move to multi-monitor

1) Press [Ctrl] + [Alt] + [F12] keys to make.
[Intel(R) 82852/82855 GM/GME Graphics Controller Prope...]
displayed (See Figure B-2).
2) Click in the left of [Devices] tab (See Figure B-2), then select
[Extended Desktop].
User’s Manual B-7

3) Select either Monitor (CRT display) or Television, then select Apply

button, because the Primary Device is fixed into Notebook (the
display of the computer).
Figure B-2 Intel(R) 82852/82855 GM/GME Graphics Controller Prope...(1)
2. Some reproduced DVD picture may not be displayed when the display
of the computer and a CRT display are used at the same. Reduce the
resolution, use the display of the computer only, use the CRT display
only or set display device in the multi-monitor, then play DVD.
Please refer to External monitor in this manual of Chapter 8 Optional
Devices or the application guide for the setting of each display device.
3. When playback DVD title with Multiple Monitors mode, there are some
case that DVD Overlay is not shown. In this case, please try to playback
WinDVD with decreasing resolution, refresh rate or color depth after
exit WinDVD player.
4. There are some case that you can select non-support mode with
LCD/CRT Dual Clone mode or MultiMonitor mode. In this case,
please try to decrease CRT resolution, refresh rate or color depth.
B-8 User’s Manual

libretto U100
Appendix C
AT Commands
In most cases, you will not need to type AT commands manually. However,
there might be some occasions when you will need to do so.
This chapter describes AT commands for data mode. Fax and voice
commands are taken care of by application software.
The format for entering AT commands is:
ATXn
where X is the AT command, and n is the specific value for that command.
After you type in the command press Enter.
Any command issued is acknowledged with a response in either text or
numeric values known as result codes.
All commands and command-values accepted by the modem are
described in this section; any entry other than those listed results in an
error.
+++ Escape sequence

The escape sequence allows the modem to exit data mode and enter
on-line command mode. While in on-line command mode, you can
communicate directly to your modem using AT commands. Once you finish,
you can return to data mode using the ATO command.
A pause, the length of which is set by Escape Guard Time (S12), must be
completed after an escape sequence is entered. This pause prevents the
modem from interpreting the escape sequence as data.
The value of the escape sequence character may be changed using
register S2.
A/ Repeat last command

This command repeats the last command string entered. Do not precede
this command with an AT prefix or conclude it by pressing Enter.
A Answer command
This command instructs the modem to go off-hook and answer an incoming
call.
User’s Manual C-1

AT Commands
Bn Communication standard setting

This command determines the communication standard CCITT or Bell.
B0 Selects CCITT V.22 mode when the modem is at 1200 bps.
B1 Selects Bell 212A when the modem is at 1200 bps (default).
B15 Selects V.21 when the modem is at 300 bps.
B16 Selects Bell 103J when the modem is at 300 bps (default).
Result Codes:
OK n=0,1,15,16
ERROR Otherwise
Dn Dial
This command instructs the modem to dial a telephone number. Enter n
(the telephone number and any modifiers) after the ATD command.
Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone
digits. Characters such as spaces, hyphens, and parentheses do not count.
They are ignored by the modem, but you may want to include them to make
the number and modifiers easier to read.
The following may be used as phone number modifiers:
P Pulse dialing.
T Touch-tone dialing (default).
, Pause during dialing. Pause for time specified in Register S8
before processing the next character in the dial string.
W Wait for dial tone. Modem waits for a second dial tone before
processing the dial string.
@ Wait for quiet answer. Wait for five seconds of silence after
dialing the number. If silence is not detected, the modem
sends a NO ANSWER result code back to the caller.
! Hook flash. Causes the modem to go on-hook for 0.5
seconds and then return to off-hook.
; Return to command mode. Causes the modem to return to
command mode after dialing a number, without
disconnecting the call.
S=n Dial a telephone number previously stored using the &Zn=X
command (See &Zn=X command for more information). The
range is 0-3.
C-2 User’s Manual

AT Commands
En Echo command
This command controls whether or not the characters entered from your
computer keyboard are displayed on your monitor (echoed) while the
modem is in command mode.
E0 Disables echo to the computer.
E1 Enables echo to the computer (default).
Result Codes:
OK n=0,1
ERROR Otherwise
Hn Hook control
This command instructs the modem to go on-hook to disconnect a call,
or off-hook to make the phone line busy.
H0 Modem goes on-hook (default).
H1 Modem goes off-hook.
Result Codes:
OK n=0,1
ERROR Otherwise
In Request ID information
This command displays product information about the modem.
I0 Returns modem identity string and driver version number.
I3 Same as I0.
I9 Returns region ID in English.
Result Codes:
OK n=0,3,9
ERROR Otherwise
Ln Monitor speaker volume

This command sets speaker volume to low, medium, or high.
L0 Low volume.
L1 Low volume. (Same as L0)
L2 Medium volume (default).
L3 High volume.
Result Codes:
OK n=0,1,2,3
ERROR Otherwise
User’s Manual C-3

AT Commands
Mn Monitor speaker mode

This command turns the speaker on or off.
M0 The speaker is off.
M1 The speaker is on until the modem detects the carrier signal
(default).
M2 The speaker is always on when modem is off-hook.
M3 Speaker is on until the carrier is detected, except when
dialing.
Result Codes:
OK n=0,1,2,3
ERROR Otherwise
Nn Modulation handshake
This command controls whether or not the local modem performs a
negotiated handshake at connection time with the remote modem when the
communication speed of the two modems is different.
N0 When originating or answering, this is for handshake only at
the communication standard specified by S37 and the ATB
command.
N1 When originating or answering, begin the handshake at the
communication standard specified by S37 and the ATB
command (default). During handshake, a lower transmission
speed may be selected.
Result Codes:
OK n=0,1
ERROR Otherwise
On Return on-line to data mode

O0 Instructs the modem to exit on-line command mode and
return to data mode (see AT escape sequence, +++).
O1 This command issues a retrain before returning to on-line
data mode.
O3 This command issues a rate renegotiation before returning to
on-line data mode.
Result Codes:
OK n=0,1,3
ERROR Otherwise
P Select pulse dialing

This command configures the modem for pulse (non touch-tone) dialing.
Dialed digits are pulsed until a T command or dial modifier is received.
Tone dial is the default setting.
C-4 User’s Manual

AT Commands
Qn Result code control

Result codes are informational messages sent from the modem and
displayed on your monitor. Basic result codes are OK, CONNECT, RING,
NO CARRIER, and ERROR. The ATQ command allows the user to turn
result codes on or off.
Q0 Enables modem to send result codes to the computer
(default).
Q1 Disables modem from sending result codes to the computer.
Result Codes:
OK n=0,1
ERROR Otherwise
T Select tone dialing

This command instructs the modem to send DTMF tones while dialing.
Dialed digits are tone dialed until a P command or dial modifier is received.
This is the default setting.
Vn DCE response format

This command controls whether result codes (including call progress and
negotiation progress messages) are displayed as words or their numeric
equivalents.
V0 Displays result codes as digits.
V1 Displays result codes as text (default).
Result Codes:
OK n=0,1
ERROR Otherwise
User’s Manual C-5

AT Commands
Xn Result code selection, call progress monitoring

This command selects which result codes will be used by the modem.
Command Dial tone Busy Supported Result Code

detect signal
detect
X0 Disable Disable OK, CONNECT, RING, NO CARRIER,

ERROR
X1 Disable Disable OK, RING, NO CARRIER, ERROR,

CONNECT <RATE>
X2 Enable Disable OK, RING, NO CARRIER, ERROR,

NODIALTONE, CONNECT <RATE>
X3 Disable Enable OK, RING, NO CARRIER, ERROR, BUSY,

CONNECT <RATE>, BLACKLISTED
X4 (default) Enable Enable OK, RING, NO CARRIER, ERROR,

NODIALTONE, BUSY, CONNECT <RATE>,
DELAYED, BLACKLISTED, REORDER,
WARBLE, CALL WAITING DETECTED
X5 Enable Enable OK, RING, NO CARRIER, ERROR,

NODIALTONE, BUSY, CONNECT <RATE>,
RRING, NO BONGTONE, DELAYED,
BLACKLISTED, REORDER, WARBLE, CALL
WAITING DETECTED
Dial tone detect

Disabled: The modem dials a call regardless of whether it detects a dial
tone.
Enabled: The modem dials only upon detection of a dial tone, and
disconnects the call if the dial tone is not detected within
10 seconds.
Busy tone detect

Disabled: The modem ignores any busy tones it receives.
Enabled: The modem monitors for busy tones.
Result Codes:
OK n=0,1,2,3,4,5
ERROR Otherwise
C-6 User’s Manual

AT Commands
Zn Recall stored profile

The modem performs a soft reset and restores (recalls) the configuration
profile according to the parameter supplied. If no parameter is specified,
zero is assumed. Either Z0 or Z1 restores the profile.
Result Codes:
OK n=0,1
ERROR Otherwise
&Cn Data Carrier Detect (DCD) control

Data Carrier Detect is a signal from the modem to the computer indicating
that a carrier signal is being received from a remote modem. DCD normally
turns off when the modem no longer detects the carrier signal.
&C0 The state of the carrier from the remote modem is ignored.
DCD circuit is always on.
&C1 DCD turns on when the remote modem’s carrier signal is
detected, and off when the carrier signal is not detected
(default).
Result Codes:
OK n=0,1
ERROR Otherwise
&Dn DTR control

This command interprets how the modem responds to the state of the DTR
signal and changes to the DTR signal.
&D0 Ignore. The modem ignores the true status of DTR and treats
it as always on. This should only be used if your
communication software does not provide DTR to the modem
&D1 If the DTR signal is not detected while in on-line data mode,
the modem enters command mode, issues an OK result
code, and remains connected.
&D2 If the DTR signal is not detected while in on-line data mode,
the modem disconnects (default).
&D3 Reset on the on-to-off DTR transition.
Result Codes:
OK n=0,1,2,3
ERROR Otherwise
&F Load factory settings

This command loads the configuration stored and programmed at the
factory. This operation replaces all of the command options and the
S-register settings in the active configuration with factory values.
&F Recall factory setting as active configuration.
User’s Manual C-7

AT Commands
&Gn V.22bis guard tone control

This command determines which guard tone, if any, to transmit while
transmitting in the high band (answer mode). This command is only used in
V.22 and V.22bis mode. This option is not used in North America and is for
international use only.
&G0 Guard tone disabled (default).
&G1 Sets guard tone to 550 Hz.
&G2 Sets guard tone to 1800 Hz.
Result Codes:
OK n=0,1,2
ERROR Otherwise
&Kn Local flow control selection

&K0 Disable flow control.
&K3 Enable CTS/RTS flow control (default).
&K4 Enable XON/XOFF flow control.
Result Codes:
OK n=0,3,4
ERROR Otherwise
&Pn Select Pulse Dial Make/Break Ratio (WW)

&P0 Selects 39% - 61% make/break ratio at 10 pulses per
second.
second.
second.
Result Codes:
OK n=0,1,2
ERROR Otherwise
&Tn Self-test commands

These tests can help to isolate problems if you experience periodic data
loss or random errors.
&T0 Abort. Stops any test in progress.
&T1 Local analog loop. This test verifies modem operation, as
well as the connection between the modem and computer.
Any data entered at the local DTE is modulated, then
demodulated, and returned to the local DTE. To work
properly, the modem must be off-line.
Result Codes:
OK n=0
CONNECT n=1
ERROR Otherwise
C-8 User’s Manual

AT Commands
&V Display Current Configuration

This command displays the current configuration of the modem. If
nonvolatile memory is supported the stored profiles are displayed as well.
&V View profiles.
&W Store current configuration

Saves the current (active) configuration (profile), including S-Registers.
The current configuration comprises a list of storable parameters illustrated
in the &V command. These settings are restored to the active configuration
upon receiving a Zn command or at power up. Refer to the &V command.
&W Stores the current configuration.
&Zn=x Store telephone number

This command is used to store up to four dialing strings in the modem’s
nonvolatile memory for later dialing. The format for the command is
&Zn=“stored number” where n is the location 0-3 to which the number
should be written. The dial string may contain up to 34 characters.
The ATDS=n command dials using the string stored in location n.
Result Codes:
OK n=0, 1, 2, 3
ERROR Otherwise
\Nn Error control mode selection

This command determines the type of error control used by the modem
when sending or receiving data.
\N0 Buffer mode. No error control.
\N1 Direct mode.
\N2 MNP or disconnect mode. The modem attempts to connect
using MNP2-4 error control procedures. If this fails, the
modem disconnects.
This is also known as MNP reliable mode.
\N3 V.42, MNP, or buffered (default).
The modem attempts to connect in V.42 error control mode.
If this fails, it attempts to connect in MNP mode. If this fails,
it connects in buffer mode and continues operation. This is
also known as V.42/MNP auto reliable mode (same as &Q5).
\N4 V.42 or disconnect. The modem attempts to connect in V.42
error control mode. If this fails, the modem disconnects.
\N5 V.42. MNP or buffered (same as \N3).
\N7 V.42. MNP or buffered (same as \N3).
Result Codes:
OK n=0,1,2,3,4,5,7
ERROR Otherwise
User’s Manual C-9

AT Commands
\Qn Local flow control selection

\Q0 Disable flow control.
\Q1 XON/XOFF software flow control.
\Q3 CTS/RTS to DTE (default).
Result Codes:
OK n=0,1,3
ERROR Otherwise
\Vn Protocol result code

\V0 Disable protocol result code appended to DCE speed.
\V1 Enable protocol result code appended to DCE speed
(default).
Result Codes:
OK n=0,1
ERROR Otherwise
%B View numbers in blacklist

If blacklisting is in effect, this command displays the numbers for which the
last call attempted in the past two hours failed. The ERROR result code
appears in regions that do not require blacklisting.
%Cn Data compression control

This command determines the operation of V.42bis and MNP class 5 data
compression. On-line changes do not take effect until a disconnect occurs
first.
%C0 V.42bis/MNP 5 disabled. No data compression.
%C3 V.42bis/MNP 5 enabled. Data compression enabled (default).
Result Codes:
OK n=0,3
ERROR Otherwise
C-10 User’s Manual

libretto U100
Appendix D
S-registers
S-registers contain the settings that determine how a number of functions

of the internal modem operate. For example, how many times to let the
telephone ring before the modem answers and how long to wait before it
hangs up if a connection fails. You can also customize certain AT
commands such as the escape sequence and command line termination.
The contents of the registers are changed automatically when you modify
corresponding settings in your communication software. If you choose,
however, you can display and edit the contents of the registers manually
when the modem is in command mode. If the value is out of the acceptable
range, then an error is generated.
This chapter describes the settings for each S-register.
S-register values
The format for displaying the value of an S-register is:
ATSn?
where n is the register number. After you type in the register press Enter.
The format for modifying the value of an S-register is:
ATSn=r
where n is the register number, and r is the new register value. After you
type in the register and its new value press Enter.
Some registers vary from one country/region to another.
S0 Auto answer ring number

This register determines the number of rings the modem will count
before automatically answering a call. Enter 0 (zero) if you do not
want the modem to automatically answer at all. When disabled,
the modem can only answer with an ATA command.
Range: 0-255
Default: 0
Units: rings
User’s Manual D-1

S-registers
S1 Ring counter
This register is read only. The value of S1 is incremented with each
ring. If no ring occurs over a six-second interval, this register is
cleared.
Range: 0-225
Default: 0
Units: rings
S2 AT escape character (user defined)

This register determines the ASCII values used for an escape
sequence. The default is the + character. The escape sequence
allows the modem to exit data mode and enter command mode
when on-line. Values greater than 127 disable the escape
sequence.
Range: 0-255, ASCII decimal
Default: 43
Units: ASCII
S3 Command line termination character (user defined)

This register determines the ASCII values as the carriage return
character. This character is used to end command lines and result
codes.
Default: 13 (carriage return)
Units: ASCII
S4 Response formatting character (user defined)

This register determines the ASCII value used as the line feed
character. The modem uses a line feed character in command
mode when it responds to the computer.
Default: 10 (line feed)
Units: ASCII
D-2 User’s Manual

S-registers
S5 Command line editing character (user defined)

This register sets the character recognized as a backspace and
pertains to asynchronous only. The modem will not recognize the
backspace character if it is set to a value that is greater than 32
ASCII. This character can be used to edit a command line. When
the echo command is enabled, the modem echoes back to the
local DTE the backspace character, an ASCII space character,
and a second backspace character. This means a total of three
characters are transmitted each time the modem processes the
backspace character.
Default: 8 (backspace)
Units: ASCII
S6 Wait before dialing

This register sets the length of time, in seconds, that the modem
must wait (pause) after going off-hook before dialing the first digit
of the telephone number. The modem always pauses for a
minimum of two seconds, even if the value of S6 is less that two
seconds. The wait for dial tone call progress feature (W dial
modifier in the dial string) will override the value in register S6.
This operation, however, may be affected by some ATX options
according to country/region restrictions. In some countries/regions,
S6 will set dial tone detect time.
Range: 3-255
Default: 3
Units: seconds
S7 Connection completion time-out

This register sets the time, in seconds, that the modem must wait
before hanging up because carrier is not detected. The timer is
started when the modem finishes dialing (originate), or goes
off-hook (answer). In originate mode, the timer is reset upon
detection of an answer tone if allowed by county restriction.
The timer also specifies the wait for silence time for the @ dial
modifier in seconds. S7 is not associated with the W dial modifier.
Range: 1-255
Default: 50
Units: seconds
User’s Manual D-3

S-registers
S8 Comma pause time

This register sets the time, in seconds, that the modem must
pause when it encounters a comma (,) in the dial command string.
In some countries/regions, S8 will set both wait before dialing and
comma pause time.
Range: 0-255
Default: 2
Units: seconds
S11 DTMF dialing speed

This register determines the dialing speed which is prefixed for
each country/region.
Range: 50-255
Default: 95
Units: .001 seconds
S12 Escape guard time

This register sets the value (in 20 millisecond increments) for the
required pause after the escape sequence.
Range: 0-255
Default: 50
Units: .02 seconds
D-4 User’s Manual

S-registers
S37 Dial line rate

S37 = 0 (default) maximum modem speed
S37 = 1 reserved
S37 = 2 1200/75 bps
S37 = 3 300 bps
S37 = 4 reserved
S37 = 5 1200 bps
S37 = 6 2400 bps
S37 = 7 4800 bps
S37 = 8 7200 bps
S37 = 9 9600 bps
S37 = 10 12000 bps
S37 = 11 14400 bps
S37 = 12 16800 bps
S37 = 13 19200 bps
S37 = 14 21600 bps
S37 = 15 24000 bps
S37 = 16 26400 bps
S37 = 17 28800 bps
S37 = 18 31200 bps
S37 = 19 33600 bps
User’s Manual D-5

S-registers
AT command set result codes

The following table shows the result codes.
The result code summary
Result Code Numeric Description

OK 0 Command executed
CONNECT 1 Modem connected to line
RING 2 A ring signal has been detected
NO CARRIER 3 Modem lost carrier signal, or
does not detect carrier signal, or
does not detect answer tone
ERROR 4 Invalid command
CONNECT 1200 EC*1 5 Connection at 1200 bps
NO DIAL TONE 6 No dial tone detected
BUSY 7 Busy signal detected
NO ANSWER 8 No quiet answer
D-6 User’s Manual

S-registers
DELAYED*2 88 Delay is in effect for the dialed

number
BLACKLISTED*2 89 Dialed number is blacklisted
BLACKLIST FULL*2 90 Blacklist is full
*1: EC only appears when the Extended Result Codes configuration option
is enabled. EC is replaced by one of the following symbols, depending
upon the error control method used:
V.42bis - V.42 error control and V.42bis data compression.
V.42 - V.42 error control only.
MNP 5 - MNP class 4 error control and MNP class 5 data
compression.
MNP 4 - MNP class 4 error control only.
NoEC - No error control protocol.
*2: In some countries/regions, these result codes may not appear.
User’s Manual D-7

S-registers
D-8 User’s Manual

libretto U100
Appendix E
V.90
The TOSHIBA internal modem uses V.90 technology. The modem is

capable of downstream speeds of 56kbps (kilobits per second) when
connected to an Internet service provider that supports V.90. As with any
modem, the actual throughput (speed of data transfer) depends on analog
telephone line conditions, which can vary considerably. Therefore,
many users will experience throughput in the range of 28-50kbps under
normal telephone line conditions. Upstream data flows at the V.34 rate.
V.90 rates can be achieved only when one V.90-capable host modem is
connected to another. The TOSHIBA Internal modem will select
automatically V.34 if the remote modem lacks V.90 capability or if a
combination of network and/or phone line conditions prevent V.90
connection.
V.90 mode
Function Transmission speed
Data V.90 From 56kbps (maximum) to 28kbps (minimum)

Reception only
User’s Manual E-1

V.90
Table E-1 Result codes for a V.90 connection
No. Result code Description

70 CONNECT 32000 EC* Connection at 32000 bps
* EC stands for the Error Control method, which appears only when the
extended result codes configuration option is enabled. EC is replaced by
one of the following symbols, depending on the error control method used.
V42bis V.42 error control and V.42bis data compression

V42 V.42 error control only
NoEC No error control protocol
E-2 User’s Manual

V.90
AT Command
-V90=* V.90 Dial Line Rate

-V90 sets the maximum V.90 downstream that the
modem attempts to connect.
-V90=0 V.90 disabled
-V90=1 V.90 enabled: automatic speed selection - maximum
modem speed (default)
User’s Manual E-3

V.90
E-4 User’s Manual

libretto U100
Appendix F
Wireless LAN
Card Specifications
Form Factor Mini PCI Type III
Compatibility ■ IEEE 802.11 Standard for Wireless LANS

■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi
Alliance. The ‘Wi-Fi CERTIFIED’ logo is a
certification mark of the Wi-Fi Alliance.
Network Operating ■ Microsoft Windows® Networking

System
Media Access ■ CSMA/CA (Collision Avoidance) with

Protocol Acknowledgment (ACK)
Data Rate ■ Theoretical maximum speed: 54Mbps (IEEE802.11g)

■ Theoretical maximum speed: 11Mbps (IEEE802.11b)
■ Theoretical maximum speed: 108Mbps (Turbo Mode)
User’s Manual F-1

Wireless LAN
Radio Characteristics
Radio Characteristics of Wireless LAN Cards may vary according to:
■ Country/region where the product was purchased
■ Type of product
Wireless communication is often subject to local radio regulations.
Although Wireless LAN wireless networking products have been designed
for operation in the license-free 2.4GHz band, local radio regulations may
impose a number of limitations to the use of wireless communication
equipment.
Refer to the sheet “Information to the User” for regulatory information that
may apply in your country/region.
R-F Frequency Band 2.4GHz (2400-2483.5 MHz)

(Revision B, G, Turbo Mode)
Modulation ■ DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK

Technique (Revision B)
■ OFDM-BPSK, OFDM-QPSK, OFDM-16QAM,
OFDM-64QAM (Revision G, Turbo Mode)
The range of the wireless signal is related to the transmit rate of the
wireless communication. Communications at lower transmit range may
travel larger distances.
■ The range of your wireless devices can be affected when the antennas
are placed near metal surfaces and solid high-density materials.
■ Range is also impacted due to “obstacles” in the signal path of the radio
that may either absorb or reflect the radio signal.
Supported Frequency Sub-bands

Subject to the radio regulations that apply in the countries/regions, your
Wireless LAN card may support a different set of 2.4 GHz channels.
Consult your Authorized Wireless LAN or TOSHIBA Sales office for
information about the radio regulations that apply in the countries/regions.
F-2 User’s Manual

Wireless LAN
Wireless IEEE 802.11 Channels Sets (Revision B and G)
Frequency Range 2400-2483.5 MHz

Channel ID*2
1 2412
2 2417
3 2422
4 2427
5 2432
6 2437
7 2442
8 2447
9 2452
10 2457*1
11 2462
12 2467
13 2472
*1 Factory-set default channels
*2 Refer to the sheet Approved Countries/Regions for use for the
countries/regions that in which these channels can be used.
When installing Wireless LAN cards, the channel configuration is managed
as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN card will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ For Wireless LAN cards installed in wireless clients that operating in a
peer-to-peer mode, the card will use the default channel 10.
■ In a Wireless LAN Access Point, the Wireless LAN card will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.
Wireless Channels Sets (Turbo Mode)
Frequency Range 2400-2483.5 MHz Note

Channel ID
6 2437 US only *3
*3 Available Area: US (USA, CANADA) only.
User’s Manual F-3

Wireless LAN
F-4 User’s Manual

libretto U100
Appendix G
AC Power Cord and Connectors
The power cord’s AC input plug must be compatible with the various
international AC power outlets and the cord must meet the standards for
the country/region in which it is used. All cords must meet the following
specifications:
Length: Minimum 2 meters

Wire size: Minimum 0.75 mm2
Current rating: Minimum 2.5 amperes
Voltage rating: 125 or 250 VAC
(depending on country/region’s power standards)
Certification agencies
U.S. and Canada: UL listed and CSA certified

No. 18 AWG, Type SVT or SPT-2
Australia: AS
Japan: DENANHO
Europe:
Austria: OVE Italy: IMQ
Belgium: CEBEC The Netherlands: KEMA
Denmark: DEMKO Norway: NEMKO
Finland: FIMKO Sweden: SEMKO
France: LCIE Switzerland: SEV
Germany: VDE United Kingdom: BSI
In Europe, two conductors power cord must be VDE type, H05VVH2-F or
H03VVH2-F and for three conductors power cord must be VDE type,
H05VV-F.
User’s Manual G-1

AC Power Cord and Connectors
For the United States and Canada, two pin plug configuration must be a
2-15P (250V) or 1-15P (125V) and three pin plug configuration must be
6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical
code handbook and the Canadian Electrical Code Part II.
The following illustrations show the plug shapes for the U.S.A. and Canada,
the United Kingdom, Australia and Europe.
USA United Kingdom
UL approved
BS approved
Australia Europe
AS approved Approved by the

appropriate agency
Canada
CSA approved
G-2 User’s Manual

libretto U100
Appendix H
If your computer is stolen
Always take care of your computer and try to prevent it from being stolen.
You are the owner of a valuable technical device, which may be highly
attractive to thieves, so please do not leave it unattended in a public place.
To further help protect against theft, security cables can be bought for use
with your notebook when it is being used at home or in the office.
Make a note of your computer’s machine type, model number, and serial
number, and put it in a safe place. You will find this information on the
underside of your notebook. Please also keep the receipt of the computer
you purchased.
Should your computer be stolen, however, we’ll help you try to find it.
Before contacting TOSHIBA, please prepare the following information
which is necessary to uniquely identify your computer:
■ In which country was your computer stolen?
■ What type of machine do you have?
■ What was the model number (PA number)?
■ What was the serial number (8 digits)?
■ When was it stolen, i.e. date?
■ What is your address, phone, and fax number?
To register the theft on paper, please follow these procedures:
■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below.
■ Attach a copy of your receipt showing where your computer was
purchased.
■ Either fax or send the receipt and registration form to the address
below.
To register the theft online, please follow these procedures:
■ Visit www.toshiba-europe.com on the Internet. In the product area,
choose Computer Systems.
■ In the Computer Systems page, open the Support & Downloads menu
and choose the Stolen Units Database option.
Your entries are used to track your computer at our service points.
User’s Manual H-1

If your computer is stolen
TOSHIBA Theft Registration

Send to: TOSHIBA Europe GmbH
Technical Service and Support
Leibnizstr. 2
93055 Regensburg
Germany
Fax number: +49 (0) 941 7807 921
Country stolen:
Machine type:
(e.g. TOSHIBA M40X)
Model number:
(e.g. PSA50 YXT)
Serial number:
(e.g. 12345678G)
Date stolen: Year Month Day
Owner’s details
Last name, first name:
Company:
Street:
Postal Code/City:
Country:
Phone:
Fax:
H-2 User’s Manual

libretto U100
Glossary
The terms in this glossary cover topics related to this manual.

Alternate naming is included for reference.
Abbreviations
AC: alternating current
AGP: accelerated graphics port
ANSI: American National Standards Institute
APM: advanced power manager
ASCII: American Standard Code for Information Interchange
BIOS: basic input output system
CD-ROM: Compact Disc-Read Only Memory
CD-RW: Compact Disc-ReWritable
CMOS: complementary metal-oxide semiconductor
CPU: central processing unit
CRT: cathode ray tube
DC: direct current
DDC: display data channel
DMA: direct memory access
DOS: disk operating system
DVD: digital versatile disc
DVD-R: Digital Versatile Disc-Recordable
DVD-RAM: Digital Versatile Disc-Random Access Memory
DVD-ROM: Digital Versatile Disc-Read Only Memory
DVD-RW: Digital Versatile Disc-ReWritable
ECP: extended capabilities port
FDD: floppy disk drive
FIR: fast infrared
HDD: hard disk drive
IDE: integrated drive electronics
I/O: input/output
User’s Manual Glossary-1

Glossary
IrDA: Infrared Data Association

IRQ: interrupt request
KB: kilobyte
LCD: liquid crystal display
LED: light emitting diode
LSI: large scale integration
MB: megabyte
MS-DOS: Microsoft Disk Operating System
OCR: optical character recognition (reader)
PCB: printed circuit board
PCI: peripheral component interconnect
RAM: random access memory
RGB: red, green, and blue
ROM: read only memory
RTC: real time clock
SCSI: small computer system interface
SIO: serial input/output
SXGA+: super extended graphics array plus
TFT: thin-film transistor
UART: universal asynchronous receiver/transmitter
USB: Universal Serial Bus
UXGA: ultra extended graphics array
VESA: Video Electronic Standards Association
VGA: video graphics array
VRT: voltage reduction technology
WXGA: wide extended graphics array
XGA: extended graphics array
A
AccuPoint: A pointing device integrated into the TOSHIBA computer
keyboard.
adaptor: A device that provides an interface between two dissimilar
electronic devices. For example, the AC adaptor modifies the power
from a wall outlet for use by the computer. This term also refers to
the add-in circuit cards that control external devices, such as video
monitors and magnetic tape devices.
allocate: To assign a space or function for a specific task.
alphanumeric: Keyboard characters including letters, numbers and other
symbols, such as punctuation marks or mathematical symbols.
alternating current (AC): Electric current that reverses its direction of flow
at regular intervals.
Glossary-2 User’s Manual

Glossary
analog signal: A signal whose characteristics such as amplitude and

frequency vary in proportion to (are an analog of) the value to be
transmitted. Voice communications are analog signals.
ANSI: American National Standards Institute. An organization established
to adopt and define standards for a variety of technical disciplines.
For example, ANSI defined the ASCII standard and other
information processing requirements.
antistatic: A material used to prevent the buildup of static electricity.
application: A group of programs that together are used for a specific task
such as accounting, financial planning, spreadsheets, word
processing and games.
ASCII: American Standard Code for Information Interchange. ASCII code
is a set of 256 binary codes that represent the most commonly used
letters, numbers, and symbols.
async: Short for asynchronous.
asynchronous: Lacking regular time relationship. As applied to computer
communications, asynchronous refers to the method of transmitting
data that does not require a steady stream of bits to be transmitted
at regular time intervals.
B
backup: A duplicate copy of files kept as a spare in case the original is
destroyed.
batch file: A file that can be executed from the system prompt containing a
sequence of operating system commands or executable files.
binary: The base two number system composed of zeros and ones (off or
on), used by most digital computers. The right-most digit of a binary
number has a value of 1, the next a value of 2, then 4, 8, 16, and so
on. For example, the binary number 101 has a value of 5. See also
ASCII.
BIOS: Basic Input Output System. The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from “binary digit,” the basic unit of information used by the
computer. It is either zero or one. Eight bits is one byte. See also
byte.
board: A circuit board. An internal card containing electronic components,
called chips, which perform a specific function or increase the
capabilities of the system.
boot: Short for bootstrap. A program that starts or restarts the computer.
The program reads instructions from a storage device into the
computer’s memory.
bps: Bits per second. Typically used to describe the data transmission
speed of a modem.
buffer: The portion of the computer’s memory where data is temporarily
stored. Buffers often compensate for differences in the rate of flow
from one device to another.

Glossary
bus: An interface for transmission of signals, data or electric power.

byte: The representation of a single character. A sequence of eight bits
treated as a single unit; also the smallest addressable unit within the
system.
C
cache memory: High speed memory which stores data that increases
processor speed and data transfer rate. When the CPU reads data
from main memory, it stores a copy of this data in cache memory.
The next time the CPU needs that same data, it looks for it in the
cache memory rather than the main memory, which saves time. The
computer has two cache levels. Level one is incorporated into the
processor and level two resides in external memory.
capacity: The amount of data that can be stored on a magnetic storage
device such as a floppy disk or hard disk. It is usually described in
terms of kilobytes (KB), where one KB = 1024 bytes and megabytes
(MB), where one MB = 1024 KB.
card: Synonym for board. See board.
CardBus: An industry standard bus for 32-bit PC cards.
CD-ROM: A Compact Disc-Read Only Memory is a high capacity disc that
can be read from but not written to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read data from the disc.
CD-R: A Compact Disc-Recordable disc can be written once and read
many times. See also CD-ROM.
CD-RW: A Compact Disc-ReWritable disc can be rewritten many times.
See also CD-ROM.
character: Any letter, number, punctuation mark, or symbol used by the
computer. Also synonymous with byte.
chassis: The frame containing the computer.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output functions and controlling other
chips.
CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit
fabricated on a silicon wafer that requires very little power.
Integrated circuits implemented in CMOS technology can be tightly
packaged and are highly reliable.
cold start: Starting a computer that is currently off (turning on the power).
COM1, COM2, COM3 and COM4: The names assigned to the serial and
communication ports.
commands: Instructions you enter at the terminal keyboard that direct the
actions of the computer or its peripheral devices.
communications: The means by which a computer transmits and
receives data to and from another computer or device. See parallel
interface; serial interface.

Glossary
compatibility: 1) The ability of one computer to accept and process data

in the same manner as another computer without modifying the data
or the media upon which it is being transferred.
2) the ability of one device to connect to or communicate with
another system or component.
components: Elements or parts (of a system) which make up the whole
(system).
computer program: A set of instructions written for a computer that
enable it to achieve a desired result.
computer system: A combination of hardware, software, firmware,
and peripheral components assembled to process data into useful
information.
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and the settings that define how
your system works. You use the HW Setup program to control your
system configuration.
control keys: A key or sequence of keys you enter from the keyboard to
initiate a particular function within a program.
controller: Built-in hardware and software that controls the functions of a
specific internal or peripheral device (e.g. keyboard controller).
co-processor: A circuit built into the processor that is dedicated to
intensive math calculations.
CPS: Characters Per Second. Typically used to indicate the transmission
speed of a printer.
CPU: Central Processing Unit. The portion of the computer that interprets
and executes instructions.
CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a
fluorescent screen-producing luminous spots. An example is the
television set.
cursor: A small, blinking rectangle or line that indicates the current
position on the display screen.
D
data: Information that is factual, measurable or statistical that a computer
can process, store, or retrieve.
data bits: A data communications parameter controlling the number of bits
(binary digits) used to make up a byte. If data bits = 7 the computer
can generate 128 unique characters. If data bits = 8 the computer
can generate 256 unique characters.
DC: Direct Current. Electric current that flows in one direction. This type of
power is usually supplied by batteries.
default: The parameter value automatically selected by the system when
you or the program do not provide instructions. Also called a preset
value.

Glossary
delete: To remove data from a disk or other data storage device.

Synonymous with erase.
device driver: A program that controls communication between a specific
peripheral device and the computer. The CONFIG.SYS file contains
device drivers that MS-DOS loads when you turn the computer on.
dialog box: A window that accepts user input to make system settings or
record other information.
disk drive: The device that randomly accesses information on a disk and
copies it to the computer’s memory. It also writes data from memory
to the disk. To accomplish these tasks, the unit physically rotates the
disk at high speed past a read-write head.
disk storage: Storing data on magnetic disk. Data is arranged on
concentric tracks much like a phonograph record.
display: A CRT, LCD, or other image producing device used to view
computer output.
documentation: The set of manuals and/or other instructions written for
the users of a computer system or application. Computer system
documentation typically includes procedural and tutorial information
as well as system functions.
DOS: Disk Operating System. See operating system.
driver: A software program, generally part of the operating system, that
controls a specific piece of hardware (frequently a peripheral device
such as a printer or mouse).
DVD-R (+R, -R): A Digital Versatile Disc-Recordable disk can be written
once and read many times. The DVD-R drive uses a laser to read
data from the disc.
DVD-RAM: A Digital Versatile Disc-Random Access Memory is a high-
capacity, high performance disc that lets you store large volumes of
data. The DVD-ROM drive uses a laser to read data from the disc.
DVD-ROM: A Digital Versatile Disc-Read Only Memory is a high capacity,
high performance disc suitable for play back of video and other
high-density files. The DVD-ROM drive uses a laser to read data
from the disc.
DVD-RW (+RW, -RW): A Digital Versatile Disc-ReWritable disc can be
rewritten many times.
E
echo: To send back a reflection of the transmitted data to the sending
device. You can display the information on the screen, or output it to
the printer, or both. When a computer receives back data it
transmitted to a CRT (or other peripheral device) and then
retransmits the data to printer, the printer is said to echo the CRT.
erase: See delete.

Glossary
escape: 1) A code (ASCII code 27), signaling the computer that what
follows are commands; used with peripheral devices such as
printers and modems.
2) A means of aborting the task currently in progress.
escape guard time: A time before and after an escape code is sent to the
modem which distinguishes between escapes that are part of the
transmitted data, and escapes that are intended as a command to
the modem.
execute: To interpret and execute an instruction.
Extended Capability Port: An industry standard that provides a data
buffer, switchable forward and reverse data transmission, and run
length encoding (RLE) support.
F
fast infrared: An industry standard that enables cableless infrared serial
data transfer at speeds of up to 4 Mbps.
file: A collection of related information; a file can contain data, programs,
or both.
firmware: A set of instructions built into the hardware which controls and
directs a microprocessor’s activities.
floppy disk: A removable disk that stores magnetically encoded data.
floppy disk drive (FDD): An electromechanical device that reads and
writes to floppy disks.
Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys.
folder: An icon in Windows used to store documents or other folders.
format: The process of readying a blank disk for its first use. Formatting
establishes the structure of the disk that the operating system
expects before it writes files or programs onto the disk.
function keys: The keys labeled F1 through F12 that tell the computer to
perform certain functions.
G
gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also
megabyte.
graphics: Drawings, pictures, or other images, such as charts or graphs,
to present information.
H
hard disk: A non-removable disk usually referred to as drive C. The
factory installs this disk and only a trained engineer can remove it
for servicing. Also called fixed disk.
hard disk drive (HDD): An electromechanical device that reads and writes
a hard disk. See also hard disk.

Glossary
hardware: The physical electronic and mechanical components of a

computer system: typically, the computer itself, external disk drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that equals one cycle per second.
hexadecimal: The base 16 numbering system composed of the digits 0
through 9 and the letters A, B, C, D, E, and F.
host computer: The computer that controls, regulates, and transmits
information to a device or another computer.
hot key: The computer’s feature in which certain keys in combination with
the extended function key, Fn, can be used to set system
parameters, such as speaker volume.
HW Setup: A TOSHIBA utility that lets you set the parameters for various
hardware components.
I
icon: A small graphic image displayed on the screen or in the indicator
panel. In Windows, an icon represents an object that the user can
manipulate.
i.LINK (IEEE1394): This port enables high-speed data transfer directly
from external devices such as digital video cameras.
infrared port: A cableless communications port capable of using infrared
signals to send serial data.
input: The data or instructions you provide to a computer, communication
device or other peripheral device from the keyboard or external or
internal storage devices. The data sent (or output) by the sending
computer is input for the receiving computer.
instruction: Statements or commands that specify how to perform a
particular task.
interface: 1) Hardware and/or software components of a system used
specifically to connect one system or device to another.
2) To physically connect one system or device to another to
exchange information.
3) The point of contact between user, the computer, and the
program, for example, the keyboard or a menu.
interrupt request: A signal that gives a component access to the
processor.
I/O: Input/output. Refers to acceptance and transfer of data to and from a
computer.
I/O devices: Equipment used to communicate with the computer and
transfer data to and from it.
IrDA 1.1: An industry standard that enables cableless infrared serial data
transfer at speeds of up to 4 Mbps.

Glossary
J
jumper: A small clip or wire that allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo, meaning 1000; often used as
equivalent to 1024, or 2 raised to the 10th power. See also byte and
kilobyte.
KB: See kilobyte.
keyboard: An input device containing switches that are activated by
manually pressing marked keys. Each keystroke activates a switch
that transmits a specific code to the computer. For each key, the
transmitted code is, in turn, representative of the (ASCII) character
marked on the key.
kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte
and megabyte.
L
level 2 cache: See cache.
Light Emitting Diode (LED): A semiconductor device that emits light
when a current is applied.
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets
of glass coated with transparent conducting material. The viewing-
side coating is etched into character forming segments with leads
that extend to the edge of the glass. Applying a voltage between the
glass sheets alters the brightness of the liquid crystal.
LSI: Large Scale Integration.
1) A technology that allows the inclusion of up to 100,000 simple
logic gates on a single chip.
2) An integrated circuit that uses large scale integration.
M
main board: See motherboard.
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also
kilobyte.
megahertz: A unit of wave frequency that equals 1 million cycles per
second. See also hertz.
menu: A software interface that displays a list of options on the screen.
Also called a screen.
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions. Also called the central
processing unit (CPU), one of the main parts of the computer.

Glossary
mode: A method of operation, for example, the boot mode, standby mode
or the hibernation mode.
modem: Derived from modulator/demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and
then converts modulated data (demodulates) to digital format where
received.
monitor: A device that uses rows and columns of pixels to display
alphanumeric characters or graphic images. See also CRT.
motherboard: A name sometimes used to refer to the main printed circuit
board in processing equipment. It usually contains integrated
circuits that perform the processor’s basic functions and provides
connectors for adding other boards that perform special functions.
Sometimes called a main board.
MP3: An audio compression standard that enables high-quality
transmission and real-time playback of sound files.
N
non-system disk: A formatted floppy disk you can use to store programs
and data but you cannot use to start the computer. See system disk.
nonvolatile memory: Memory, usually read-only (ROM), that is capable of
permanently storing information. Turning the computer’s power off
does not alter data stored in nonvolatile memory.
numeric keypad overlay: A feature that allows you to use certain keys on
the keyboard to perform numeric entry, or to control cursor and page
movement.
O
OCR: Optical Character Recognition (reader). A technique or device that
uses laser or visible light to identify characters and input them into a
storage device.
online state: A functional state of a peripheral device when it is ready to
receive or transmit data.
operating system: A group of programs that controls the basic operation
of a computer. Operating system functions include interpreting
programs, creating data files, and controlling the transmission and
receipt (input/output) of data to and from memory and peripheral
devices.
output: The results of a computer operation. Output commonly indicates
data.
1) printed on paper, 2) displayed at a terminal, 3) sent through the
serial port of internal modem, or 4) stored on some magnetic media.

Glossary
P
parallel interface: Refers to a type of information exchange that transmits
information one byte (8 bits) at a time. See also serial interface.
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on or off; odd or even; 0 or 1.
2) In serial communications, an error detection bit that is added to a
group of data bits making the sum of the bits even or odd. Parity can
be set to none, odd, or even.
password: A unique string of characters used to identify a specific user.
The computer provides various levels of password protection such
as user, supervisor and eject.
pel: The smallest area of the display that can be addressed by software.
Equal in size to a pixel or group of pixels. See pixel.
peripheral component interconnect: An industry standard 32-bit bus.
peripheral device: An I/O device that is external to the central processor
and/or main memory such as a printer or a mouse.
pixel: A picture element. The smallest dot that can be made on a display
or printer. Also called a pel.
plug and play: A capability with Windows that enables the system to
automatically recognize connections of external devices and make
the necessary configurations in the computer.
port: The electrical connection through which the computer sends and
receives data to and from devices or other computers.
Power Saver Utility: A TOSHIBA utility that lets you set the parameters
for various power-saving functions.
printed circuit board (PCB): A hardware component of a processor to
which integrated circuits and other components are attached. The
board itself is typically flat and rectangular, and constructed of
fiberglass, to form the attachment surface.
program: A set of instructions a computer can execute that enables it to
achieve a desired result. See also application.
prompt: A message the computer provides indicating it is ready for or
requires information or an action from you.
R
Radio frequency interference (RFI) shield: A metal shield enclosing the
printed circuit boards of the printer or computer to prevent radio and
TV interference. All computer equipment generates radio frequency
signals. The FCC regulates the amount of signals a computing
device can allow past its shielding. A Class A device is sufficient for
office use. Class B provides a more stringent classification for home
equipment use. TOSHIBA portable computers comply with Class B
computing device regulations.
Random Access Memory (RAM): High speed memory within the
computer circuitry that can be read or written to.

Glossary
restart: Resetting a computer without turning it off (also called “warm boot”
or “soft reset”). See also boot.
RGB: Red, green, and blue. A device that uses three input signals, each
activating an electron gun for a primary additive color (red, green,
and blue) or port for using such a device. See also CRT.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
ROM: Read Only Memory: A nonvolatile memory chip manufactured to
contain information that controls the computer’s basic operation.
You cannot access or change information stored in ROM.
S
SCSI: Small Computer System Interface is an industry standard interface
for connection of a variety of peripheral devices.
SD card: Secure Digital cards are flash memory widely used in a variety of
digital devices such as digital cameras and Personal Digital
Assistants.
serial communications: A communications technique that uses as few as
two interconnecting wires to send bits one after another.
serial interface: Refers to a type of information exchange that transmits
information sequentially, one bit at a time. Contrast: Parallel
interface.
SIO: Serial Input/Output. The electronic methodology used in serial data
transmission.
soft key: Key combinations that emulate keys on the IBM keyboard,
change some configuration options, stop program execution, and
access the numeric keypad overlay.
software: The set of programs, procedures and related documentation
associated with a computer system. Specifically refers to computer
programs that direct and control the computer system’s activities.
See also hardware.
stop bit: One or more bits of a byte that follow the transmitted character or
group codes in asynchronous serial communications.
subpixel: Three elements, one red, one green and blue (RGB), that make
up a pixel on the color LCD. The computer sets subpixels
independently, each may emit a different degree of brightness. See
also pixel.
synchronous: Having a constant time interval between successive bits,
characters or events.
system disk: A disk that has been formatted with an operating system.
For MS-DOS the operating system is contained in two hidden files
and the COMMAND.COM file. You can boot a computer using a
system disk. Also called an operating system disk.

Glossary
T
terminal: A typewriter-like keyboard and CRT display screen connected to
the computer for data input/output.
TFT display: A liquid crystal display (LCD) made from an array of liquid
crystal cells using active-matrix technology with thin film transistor
(TFT) to drive each cell.
TTL: Transistor-transistor logic. A logic circuit design that uses switching
transistors for gates and storage.
U
Universal Serial Bus: This serial interface lets you communicate with
several devices connected in a chain to a single port on the
computer.
V
VGA: Video Graphics Array is an industry standard video adaptor that lets
you run any popular software.
volatile memory: Random access memory (RAM) that stores information
as long as power is supplied to the computer.
W
warm start: Restarting or resetting a computer without turning it off.
window: A portion of the screen that can display its own application,
document or dialog box. Often used to mean a Microsoft Windows
window.
Wireless LAN: Local Area Network (LAN) through wireless
communication.
write protection: A method for protecting a floppy disk from accidental
erasure.

Glossary

libretto U100
Index
A D
AC adaptor, 1-6 DC IN indicator, 2-9, 6-3
additional, 1-17, 8-9 Display, 1-8, 2-8
connecting, 3-7 automatic power off, 1-12
DC IN 15V jack, 2-2 brightness decrease, 5-5
ASCII characters, 5-9 brightness increase, 5-5
controller, 1-8, B-1
B hinge, 2-8
Battery opening, 3-9
charging, 6-8 DLA for TOSHIBA, 1-16, 4-21
extending life, 6-11 Docking port, 1-9, 2-6
indicator, 2-9, 6-2 Documentation list, 1-3
monitoring capacity, 6-9 DVD Super Multi drive, 1-7
real time clock, 1-6, 6-4 problems, 9-10
safety precautions, 6-5 using, 4-10
save mode, 1-13 writing, 4-16
types, 6-3 DVD-ROM&CD-R/RW drive, 1-7
Battery pack, 1-5, 2-5 problems, 9-9
additional, 8-9 using, 4-10
replacing, 6-12 writing, 4-14
Bluetooth, 1-10, 4-33
problems, 9-19 E
TOSHIBA Stack, 1-15 Environment, 3-1
Boot Priority, 7-2 Equipment checklist, 1-1
Equipment setup
C general conditions, 3-2
Cleaning the computer, 4-37 placement, 3-3
Cooling vents, 2-2 Ergonomics
lighting, 3-5
seating and posture, 3-4
work habits, 3-5
User’s Manual Index-1

Index
F Hot keys, 1-12

display selection, 5-5
Fingerprint Sensor
instant security, 5-4
problems, 9-13
Internal LCD screen brightness
using, 4-3
decrease, 5-5
Floppy disk care, 4-25
Internal LCD screen brightness
Fn + Ctrl (enhanced keyboard
increase, 5-5
simulation), 5-3
power save mode, 5-4
Fn + Enter, 5-3
sound mute, 5-4
Fn + Esc (sound mute), 5-4
standby, 5-4
Fn + F1 (instant security), 5-4
wireless setting, 5-6
Fn + F10 (Arrow mode), 5-3
HW Setup, 1-14
Fn + F11 (Numeric mode), 5-3
accessing, 7-1
Fn + F12 (ScrLock), 5-3
boot priority, 7-2
Fn + F2 (power save mode), 5-4
CPU, 7-5
Fn + F3 (Stand by), 5-4
Device Config, 7-6
Fn + F4 (Hibernation), 5-5
display, 7-2
Fn + F5 (display selection), 5-5
general, 7-1
Fn + F6 (display brightness decrease),
keyboard, 7-5
5-5
LAN, 7-6
Fn + F7 (display brightness increase),
USB, 7-6
5-5
window, 7-1
Fn + F8 (wireless setting), 5-6
FN + INS (change insertion/overwrite),
5-3
I
FN + PGDN (move to next page), 5-3 i.LINK, 1-9, 2-2, 8-11
FN + PGUP (move to last page), 5-3 connecting, 8-12
Fn + Space (LCD screen resolution disconnecting, 8-12
selection), 5-6 precautions, 8-11
Function keys, 5-2 problems, 9-17
Indicators, 2-9, 6-2
G
Graphics controller, 1-8
K
Keyboard, 1-8, 5-1
H emulating enhanced keyboard,
5-2
Hard disk drive, 1-6
Fn Sticky key, 5-6
automatic power off, 1-12
Function keys F1...F12, 5-2
HDD indicator, 2-9
hot keys, 5-4
Heat dispersal, 1-13, 4-41
problems, 9-7
Hibernation, 1-14, 5-5
typewriter keys, 5-1
Windows special keys, 5-7
Index-2 User’s Manual

Index
Keypad overlay, 1-13, 5-7 P

Arrow mode, 5-7
Password
Numeric mode, 5-8
power on, 1-13
temporarily using normal
problems, 9-7
keyboard (overlay on), 5-8
starting the computer by, 6-16
temporarily using overlay
Supervisor, 6-16
(overlay off), 5-8
user, 6-15
turning on the overlays, 5-7
PC card, 1-9, 8-2
L inserting, 8-2
problems, 9-12
LAN, 1-10, 4-35 removing, 8-3
cable types, 4-35 Pointing Device, 1-8
connecting, 4-36 AccuPoint, 2-8
disconnecting, 4-36 AccuPoint control buttons, 2-8
jack, 2-5 problems, 9-12
problems, 9-18 Ports
Docking port, 1-9
M i.LINK, 1-9
Media care, 4-24 Mini-RGB, 1-9
CD/DVDs, 4-24 USB, 1-9
floppy disks, 4-25 Power
SD card, 8-5 conditions, 6-1
Memory, 1-5 hibernation mode, 3-11
expansion, 1-17, 8-6 indicators, 6-2
installing, 8-7 panel on/off, 1-13, 6-17
problems, 9-15 shut down mode (boot mode),
removing, 8-8 3-11
Mini-RGB port, 1-9, 2-3 standby mode, 3-13
Modem, 1-10, 4-27 system auto off, 6-17
connecting, 4-31 turning off, 3-11
disconnecting, 4-32 turning on, 3-10
ferrite core, 4-29 Power-up modes, 6-16
jack, 2-4 Problems
problems, 9-17 AC power, 9-5
properties menu, 4-28 AccuPoint, 9-12
region selection, 4-28 Analyzing symptoms, 9-2
Monitor Battery, 9-6
external, 8-10 Bluetooth, 9-19
problems, 9-16 DVD Multi drive, 9-10
Moving the computer, 4-37 DVD Super Multi drive, 9-10
DVD-ROM&CD-R/RW drive, 9-9
External monitor, 9-16
User’s Manual Index-3

Index
Fingerprint Sensor, 9-13 Sound System, 4-26

Hard disk drive, 9-8 headphone jack, 1-9, 2-4
Hardware and system checklist, microphone, 4-26
9-3 microphone jack, 1-9, 2-4
i.LINK, 9-17 mute hot keys, 5-4
Internal LCD display panel, 9-8 problems, 9-16
Keyboard, 9-7 Stereo speakers, 2-8
LAN, 9-18 volume control, 2-4
Memory expansion, 9-15 Standby, 1-14
Modem, 9-17 setting, 3-13
mouse, USB, 9-14 System automatic, 1-12
Overheating power down, 9-5
Password, 9-7 T
PC card, 9-12 TOSHIBA Assist, 1-15
Pointing Device, 9-12 TOSHIBA ConfigFree, 1-16
Power, 9-4 TOSHIBA PC Diagnostic Tool, 1-16
SD card, 9-12 TOSHIBA Power Saver, 1-14
Self test, 9-4 TOSHIBA SD Memory Boot Utility,
Sound System, 9-16 1-15
System start-up, 9-3 TOSHIBA Theft Registration, H-2
TOSHIBA support, 9-20 TOSHIBA Zooming Utility, 1-15
USB, 9-15
USB floppy disk drive, 9-11 U
Wireless LAN, 9-18 USB, 1-9, 2-4
Processor, 1-4 problems, 9-15
USB floppy disk drive, 1-6
R additional, 8-10
RecordNow!, 1-15, 4-20 problems, 9-11
Recovery Media, 3-19 using, 4-9
Restarting the computer, 3-14
V
S Video modes, B-1
SD card, 1-9, 8-3 Video RAM, 1-5
care, 8-5 Volume control, 2-4
inserting, 8-4
problems, 9-12 W
removing, 8-5 Wireless communication, 4-32
Soft keys indicator, 2-10, 4-35
enhanced keyboard, 5-2 switch, 1-12, 2-3, 4-34
Enter, 5-3 Wireless LAN, 1-11, 4-32, F-1
right Ctrl key, 5-3 problems, 9-18
ScrLock, 5-3
Index-4 User’s Manual

SPR6LU100EN0

Uploaded by

Copyright:

Available Formats

SPR6LU100EN0

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SPR6LU100EN0

Uploaded by

Copyright:

Available Formats

libretto U100

Portable Personal Computer

Modem warning notice

User’s Manual iii

Be sure to check the international precautions at the end of this section.

■ The DVD-ROM and CD-R/RW drive employs a laser system. To ensure

CAUTION: This appliance contains a

CLASS 1 LASER PRODUCT VORSICHT: Dieses Gerät enthält ein

ADVERSEL: USYNLIG ADVARSEL: Denne mærking er anbragt

User’s Manual vii

viii User’s Manual

xii User’s Manual

TOSHIBA computers are designed to optimize safety, minimize strain and

User’s Manual xiii

Pressure or impact damage

xiv User’s Manual

Congratulations on your purchase of the libretto U100 computer. This

Chapter 4, Operating Basics, includes instructions on using the following

xvi User’s Manual

ABC When procedures require an action such as

Names of windows or icons or text generated by

Indicates a potentially hazardous situation, which could result in death or

User’s Manual xvii

xviii User’s Manual

This chapter provides an equipment checklist, and it identifies the

* indicates an optional part that is dependant on the model purchased

User’s Manual 1-1

Microsoft® Windows XP Professional

Microsoft® Windows XP Home Edition

1-2 User’s Manual

Documentation, backup media and additional software

User’s Manual 1-3

1-4 User’s Manual

CPU performance may also vary from specifications due to design

Disclaimer (General Main Memory Disclaimer)

Video RAM Part of system memory is used for Video RAM.

User’s Manual 1-5

Disclaimer (Battery Life)

Disclaimer (HDD Drive Capacity)

USB floppy disk Accommodates either 3 1/2" 1.44-megabyte or

1-6 User’s Manual

DVD-ROM and Some models are equipped with a full-size,

■ The optical media drive is optional.

User’s Manual 1-7

Graphics controller The graphics controller maximizes display

Disclaimer (Graphics Processor Unit (“GPU”))

Built-in AccuPoint This pointer control stick, located in the center of

1-8 User’s Manual

Mini-RGB Analog VGA port supports VESA DDC2B

User’s Manual 1-9

Modem An internal modem provides capability for data

1-10 User’s Manual

Wireless LAN*6 Some computers in this series are equipped with

User’s Manual 1-11

Disclaimer (Wireless LAN/Atheros)

Wireless This switch turns the Wireless LAN and

1-12 User’s Manual

Keypad overlay A ten-key pad is integrated into the keyboard.

Heat dispersal To protect from overheating, the CPU has an

HDD Protection Using the acceleration sensor built into the