0% found this document useful (0 votes)
17 views54 pages

Angle Modulation Lecture 9 & 10

This document discusses frequency modulation (FM) and phase modulation (PM). It covers narrowband FM and wideband FM, including their spectra and bandwidth requirements. The key points are: 1) Narrowband FM has a modulation index β << 1 and requires the same bandwidth as AM. Wideband FM has β >> 1 and its bandwidth increases with β. 2) The spectrum of FM contains a carrier and an infinite number of sidebands located symmetrically around the carrier at multiples of the modulating frequency fm. 3) Carson's rule states the minimum bandwidth to transmit 98% of an FM signal's power is BW ≈ 2(1+β)fm. Narrowband
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
17 views54 pages

Angle Modulation Lecture 9 & 10

This document discusses frequency modulation (FM) and phase modulation (PM). It covers narrowband FM and wideband FM, including their spectra and bandwidth requirements. The key points are: 1) Narrowband FM has a modulation index β << 1 and requires the same bandwidth as AM. Wideband FM has β >> 1 and its bandwidth increases with β. 2) The spectrum of FM contains a carrier and an infinite number of sidebands located symmetrically around the carrier at multiples of the modulating frequency fm. 3) Carson's rule states the minimum bandwidth to transmit 98% of an FM signal's power is BW ≈ 2(1+β)fm. Narrowband
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 54

Lecture 9 & 10

Chapter 4

Angle Modulation:
Frequency Modulation (FM)
Phase Modulation (PM)
FM with Single Tone Modulating Signal
Now, We need to investigate the bandwidth of FM

Depending on the value of the modulation index we have


two cases of frequency modulation

Narrowband FM Wideband FM
 1  1
Narrowband FM (NBFM)
Narrowband FM (NBFM)

since
Which is similar to the AM signal which is given by:

BT = 2 f
m

The difference between the two equations (AM & NBFM) is the –ve
sign in the last term. Thus the NBFM requires the same transmission
The transmission
bandwidth as AM.
bandwidth of the NBFM
is similar to the AM
Generation of Narrowband FM

AcA mk f
sin(mt )sin(ct)
2f m

m(t) = Am cos (2f mt )

Am
 m( ) d = 2f sin(mt )
m
Wideband FM (WBFM)
Now we determine the spectrum of the single tone FM signal for an
arbitrary value of the modulation index 

s (t ) = Ac cos (ct +  sin (mt )



= Re Ace 
J(c t +  sin (m t))

= Re
(A e  (
c e 
J sin
 m t)) J ct c

= Re 
 J ct
c(t) e
J sin (m t))
where c(t) = Ace is the complex
envelope of FM signal.
Wideband FM (WBFM)

Where:
Wideband FM (WBFM)
Bessel function
Wideband FM (WBFM)
Transmission Bandwidth of FM Signals
In theory, an FM signal contains an infinite number of side frequencies so that
the bandwidth required to transmit such a signal is similarly infinite in extent.
✓ It can be shown that 98 percent of the normalized total signal power is
contained in the bandwidth
This expression can

BW  2(1+  ) f m Hz
represents the general
Carson’s rule case where f m is the max.
frequency in the signal

NARROW-BAND ANGLE-MODULATED WIDE-BAND ANGLE-MODULATED


SIGNALS SIGNALS

 1  BW  2(1+  )f m  1 BW  2(1+  )f m


 BW  2 f m Hz f
 BW  2( )f m  2  f m = 2f Hz
fm
✓ Usually a value of β<0.2 is
sufficient to satisfy this
condition. The larger the modulation
Index, the larger the
bandwidth
Transmission Bandwidth of FM Signals

Another form of FM Bandwidth:


Example:
Example (Cont.)

B = 2(2 10kHz) = 40 kHz B = 2(n f m )

BW  2(1+  ) f m Hz 
B = 2(1 + 1)  10 k H z = 40 k H z
Example (Cont.)

Calculate the magnitudes ????


Transmitted Power of WBFM

Since
T

Note this can be deduced easily (from the three form of representation of bandpass signals) as :
1
PT =  c(t)  where c(t) = Ac e j (t )
2

2
1 1
=  Ac = Ac2
2

2 2
Spectrum of WBFM

Spectrum of WBFM

s FM (t ) = A c  J ( )co s (2 f
n c t + 2 n f m t )
n=−


S FM ( f ) = Ac  J n ( ) ( f − ( f c + n f m )) +  ( f + ( f c + n f m ))
2 n=−

= c J o ( ) ( f − f c ) + J o ( ) ( f + f c )
A n=0
2
+ c J 1 ( ) ( f − ( f c + f m ))+ J 1 ( ) ( f + ( f c + f m ))
A n=1
2
+ c J 2 ( ) ( f − ( f c + 2 f m ))+ J 2 ( ) ( f + ( f c + 2 f m ))
A
n=2
2
+ c J 3( ) ( f − ( f c + 3 f m ))+ J 3 ( ) ( f + ( f c + 3 f m ))
A
2
n=3
+ c J ( ) ( f − ( f + 4 f ))+ J ( ) ( f + ( f + 4 f )) +
A
2 4 c m 4 c m
n=4
.
.
n = -1
+
Ac
J −1 ( ) ( f − ( f c − f m ))+ J −1 ( ) ( f + ( f c − f m ))
2
+ A c J − 2 ( ) ( f − ( f c − 2 f m ))+ J − 2 ( ) ( f + ( f c − 2 f m )) n = -2
2
+ A c J − 3 ( ) ( f − ( f c − 3 f m ))+ J 3 ( ) ( f + ( f c − 3 f m )) n = -3
2
+ A c J − 4 ( ) ( f − ( f c − 4 f m ))+ J − 4 ( ) ( f + ( f c − 4 f m )) + n = -4
2
.
 =2
5
Ac = 10 V
J o (2 ) c =  0.239 = 1.14
4 .5 A 10
4
2 2
3 .5 A 10
J 2 (32)
Ac = 10  0.3528 = 1.764 J1 (2) c
=  0.5767 = 2.835 f c = 500 [Hz]
M(f) 2 2 2 2
f m = 50 [Hz]
2 .5
XF

Ac = 10  0.1289 = 0.644
J 12 (. 52)
1 2 2
0 .5

0
0 100 200 300 400 500 600 700 800 900 1000
F R E Q U E N C Y [Hz]

 = 0.5
5

J o (0.5)
4.5 Ac 10
=  0.9385 = 4.6955
4 2 2
3.5

J1(0.5)
3 Ac = 10  0.2423 = 1.215
2 2
M(f)

2.5
XF

1.5
J 2 (0.5)
Ac 10
1
=  0.03060 = 0.1530
2 2
0.5

0
0 100 200 300 400 500 600 700 800 900 1000
F R E Q U E N C Y [Hz]
Spectrum of WBFM
(1)The spectrum of an FM signal contains a carrier component
and an infinite set of sideband frequencies located
symmetrically on either side of the carrier at frequency

separation of f m , 2 f m ,3 f m ,...

(2) For the special case of  1 , Only the Bessel


coefficients J 0 ( ) and J1( ) have significant values so that the
spectrum of the FM is composed of a carrier and a single

pair of side frequencies at fc  f m


(3) Unlike the AM signal, the amplitude of the
carrier component varies with the modulation
index
Remember: FM with Single Tone Modulating Signal

s(t) = Ac cos[ct +  sin (mt )] (1)

where
Δf
β= Δf = β f m
fm
is the modulation index of the FM signal.

f = k f Am

Am is the amplitude of the modulating signal


Example: Spectrum of WBFM Normalized amplitude

In this example, we investigate


the ways in which variations in
the amplitude and frequency of a
sinusoidal modulating signal
affect the spectrum of WBFM
signal.

Case I: The frequency of the


modulating Signal is fixed but its
amplitude is varied producing a
frequency deviation f
As Am increases,f increases,,then  increases

See the amplitude


variation of the spectrum
for different 
Example: (Cont.)
Case II: The amplitude of
the modulating Signal is
fixed (producing constant
frequency deviation )but
its frequency is varied.

As β increases, f m decreases;Since Am is constant

We see that when the


frequency deviation is
constant and the
modulation index is
increased, we have an
increasing number of
spectral lines crowding
into a fixed frequency
interval:
Example (Cont.):
That is when  approaches infinity, the bandwidth of the
FM signal approaching the limiting value of 2f which is an
important point to keep in mind for later discussion.
Difference between AM and Angle Modulation

(1)Zero crossings (instants of time at which a waveform


changes from a negative to a a positive value) no longer
have a perfect regularity in their spacing.
(2)The envelope of FM or PM signal is constant (equal to the
carrier amplitude), where as the envelope of an AM signal
is dependent on the message signal.
(3)The FM signal s(t) is a nonlinear function of the modulating
signal m(t) which makes FM to be a nonlinear modulation
process.
(4)Unlike AM, the spectrum of an FM signal is not related in a
simple manner to that of the modulating signal, rather, its
analysis is much more difficult than that of an AM signal.
Advantages of FM over AM
Disadvantages of FM over AM
Generation of FM Signals:
Direct Method (Parameter Variation Method)
In this method, the carrier frequency is directly varied in
accordance with the input baseband signal, which is
performed using voltage controlled oscillator.

x(t) A cos(2f t + cx(t))


c c
VCO
Generation of FM Signals:
Indirect Method NBFM WBFM

This method is preferred when the carrier frequency stability is


of major concern as in commercial radio broadcasting
Frequency Multiplier
f
Remember : s(t) = Ac cos[ ct + sin( mt )]
fm
= Ac cos[c t +  sin (

Example:
Demodulation of FM Signals
+VL

R eceived signal S ( t )

+VL

+VL

Limited signal S L ( t )

+VL

The received FM signal is passed to a BPF to remove


the out of band noise and then passed to a limiter to
remove any amplitude fluctuations due to noise. The next
step, the FM signal is demodulated to extract the signal.
Q1
If m(t) = Sin(2000 t) k f = 100 KHz/V and k p = 10 rad/V
Q. 7 What is the peak phase deviation?

Q. 8 Either the given signal is NB or WB?

Q. 9 What is the peak frequency deviation?

You might also like