THREE PHASE TRANSFORMER CONNECTION:

Three Phase Transformers:

Thus far we have looked at the construction and operation of the single-phase, two winding
voltage transformer which can be used increase or decrease its secondary voltage with respect to
the primary supply voltage But voltage transformers can also be constructed for connection to
not only one single phase, but for two-phases, three-phases, six-phases and even elaborate
combinations up to 24-phases for some DC rectification transformers.

If we take three single-phase transformers and connect their primary windings to each other and
their secondary windings to each other in a fixed configuration, we can use the transformers on a
three-phase supply.See the connection of three phase transfprmer below

.
Three-phase, also written as 3-phase or 3φ supplies are used for electrical power generation,
transmission, and distribution, as well as for all industrial uses. Three-phase supplies have many
electrical advantages over single-phase power and when considering three-phase transformers we
have to deal with three alternating voltages and currents differing in phase-time by 120 degrees
as shown below.

Three Phase Voltages and Currents

Where: VL is the line-to-line voltage, and VP is the phase-to-neutral voltage.

A transformer can not act as a phase changing device and change single-phase into three-phase
or three-phase into single phase. To make the transformer connections compatible with three-
phase supplies we need to connect them together in a particular way to form a Three Phase
Transformer Configuration.

A three phase transformer or 3φ transformer can be constructed either by connecting together

three single-phase transformers, thereby forming a so-called three phase transformer bank, or by
using one pre-assembled and balanced three phase transformer which consists of three pairs of
single phase windings mounted onto one single laminated core.
The advantages of building a single three phase transformer is that for the same kVA rating it
will be smaller, cheaper and lighter than three individual single phase transformers connected
together because the copper and iron core are used more effectively. The methods of connecting
the primary and secondary windings are the same, whether using just one Three Phase
Transformer or three separate Single Phase Transformers. Consider the circuit below:

Three Phase Transformer Connections

The primary and secondary windings of a transformer can be connected in different

configuration as shown to meet practically any requirement. In the case of three phase
transformer windings, three forms of connection are possible: “star” (wye), “delta” (mesh) and
“interconnected-star” (zig-zag).

The combinations of the three windings may be with the primary delta-connected and the
secondary star-connected, or star-delta, star-star or delta-delta, depending on the transformers
use. When transformers are used to provide three or more phases they are generally referred to as
a Polyphase Transformer.
THREE PHASE TRANSFORMER STAR AND DELTA CONFIGURATIONS:

But what do we mean by “star” (also known as Wye) and “delta” (also known as Mesh) when
dealing with three-phase transformer connections. A three phase transformer has three sets of
primary and secondary windings. Depending upon how these sets of windings are
interconnected, determines whether the connection is a star or delta configuration.

The three available voltages, which themselves are each displaced from the other by 120
electrical degrees, not only decided on the type of the electrical connections used on both the
primary and secondary sides, but determine the flow of the transformers currents.

With three single-phase transformers connected together, the magnetic flux’s in the three
transformers differ in phase by 120 time-degrees. With a single the three-phase transformer there
are three magnetic flux’s in the core differing in time-phase by 120 degrees.

The standard method for marking three phase transformer windings is to label the three primary
windings with capital (upper case) letters A, B and C, used to represent the three individual
phases of RED, YELLOW and BLUE. The secondary windings are labelled with small (lower
case) letters a, b and c. Each winding has two ends normally labelled 1 and 2 so that, for
example, the second winding of the primary has ends which will be labelled B1 and B2, while
the third winding of the secondary will be labelled c1 and c2 as shown.
Transformer Star and Delta Configurations:

Symbols are generally used on a three phase transformer to indicate the type or types of
connections used with upper case Y for star connected, D for delta connected and Z for
interconnected star primary windings, with lower case y, d and z for their respective secondaries.
Then, Star-Star would be labelled Yy, Delta-Delta would be labelled Dd and interconnected star
to interconnected star would be Zz for the same types of connected transformers.
Transformer Winding Identification:

Connection Primary Winding Secondary Winding

Delta D D

Star Y Y

Interconnected Z Z

We now know that there are four different ways in which three single-phase transformers may be
connected together between their primary and secondary three-phase circuits. These four
standard configurations are given as: Delta-Delta (Dd), Star-Star (Yy), Star-Delta (Yd), and
Delta-Star (Dy).

Transformers for high voltage operation with the star connections has the advantage of reducing
the voltage on an individual transformer, reducing the number of turns required and an increase
in the size of the conductors, making the coil windings easier and cheaper to insulate than delta
transformers.

The delta-delta connection nevertheless has one big advantage over the star-delta configuration,
in that if one transformer of a group of three should become faulty or disabled, the two remaining
ones will continue to deliver three-phase power with a capacity equal to approximately two
thirds of the original output from the transformer unit.
TRANSFORMER DELTA AND DELTA CONNECTIONS:

In a delta connected ( Dd ) group of transformers, the line voltage, VL is equal to the supply
voltage, VL = VS. But the current in each phase winding is given as: 1/√3 × IL of the line current,
where IL is the line current.

One disadvantage of delta connected three phase transformers is that each transformer must be
wound for the full-line voltage, (in our example above 100V) and for 57.7 per cent, line current.
The greater number of turns in the winding, together with the insulation between turns,
necessitate a larger and more expensive coil than the star connection. Another disadvantage with
delta connected three phase transformers is that there is no “neutral” or common connection.

In the star-star arrangement ( Yy ), (wye-wye), each transformer has one terminal connected to a
common junction, or neutral point with the three remaining ends of the primary windings
connected to the three-phase mains supply. The number of turns in a transformer winding for star
connection is 57.7 per cent, of that required for delta connection.
The star connection requires the use of three transformers, and if any one transformer becomes
fault or disabled, the whole group might become disabled. Nevertheless, the star connected three
phase transformer is especially convenient and economical in electrical power distributing
systems, in that a fourth wire may be connected as a neutral point, ( n ) of the three star
connected secondaries as shown.

TRANSFORMER STAR AND STAR CONNECTIONS:

The voltage between any line of the three-phase transformer is called the “line voltage”, VL,
while the voltage between any line and the neutral point of a star connected transformer is called
the “phase voltage”, VP. This phase voltage between the neutral point and any one of the line
connections is 1/√3 × VL of the line voltage. Then above, the primary side phase voltage, VP is
given as.

The secondary current in each phase of a star-connected group of transformers is the same as that
for the line current of the supply, then IL = IS.
Then the relationship between line and phase voltages and currents in a three-phase system can
be summarised as:

Three-phase Voltage and Current

Connection Phase Voltage Line Voltage Phase Current Line Current

Star VP = VL ÷ √3 VL = √3 × VP IP = IL IL = IP

Delta VP = VL VL = VP IP = IL ÷ √3 IL = √3 × IP

Where again, VL is the line-to-line voltage, and VP is the phase-to-neutral voltage on either the
primary or the secondary side.

Other possible connections for three phase transformers are star-delta Yd, where the primary
winding is star-connected and the secondary is delta-connected or delta-star Dy with a delta-
connected primary and a star-connected secondary.

Delta-star connected transformers are widely used in low power distribution with the primary
windings providing a three-wire balanced load to the utility company while the secondary
windings provide the required 4th-wire neutral or earth connection.

When the primary and secondary have different types of winding connections, star or delta, the
overall turns ratio of the transformer becomes more complicated. If a three-phase transformer is
connected as delta-delta ( Dd ) or star-star ( Yy ) then the transformer could potentially have
a 1:1 turns ratio. That is the input and output voltages for the windings are the same.

However, if the 3-phase transformer is connected in star–delta, ( Yd ) each star-connected

primary winding will receive the phase voltage, VP of the supply, which is equal to 1/√3 × VL.
Then each corresponding secondary winding will then have this same voltage induced in it, and
since these windings are delta-connected, the voltage 1/√3 × VL will become the secondary line
voltage. Then with a 1:1 turns ratio, a star–delta connected transformer will provide a √3:1 step-
down line-voltage ratio.

Then for a star–delta ( Yd ) connected transformer the turns ratio becomes:

Star-Delta Turns Ratio

Likewise, for a delta–star ( Dy ) connected transformer, with a 1:1 turns ratio, the transformer
will provide a 1:√3 step-up line-voltage ratio. Then for a delta-star connected transformer the
turns ratio becomes:

Delta-Star Turns Ratio

Then for the four basic configurations of a three-phase transformer, we can list the transformers
secondary voltages and currents with respect to the primary line voltage, VL and its primary line
current IL as shown in the following table.

Three-phase Transformer Line Voltage and Current

Primary-Secondary Line Voltage Line Current

Configuration Primary or Secondary Primary or Secondary
 Delta – Delta

Delta – Star

Star – Delta

Star – Star

Where: n equals the transformers “turns ratio” (T.R.) of the number of secondary windings NS,
divided by the number of primary windings NP. ( NS/NP ) and VL is the line-to-line voltage
with VP being the phase-to-neutral voltage.
 DELTA-STAR CONNECTION OF TRANSFORMER:

 In this type of connection, the primary connected in delta fashion while the secondary current
is connected in star.

 The main use of this connection is to step up the voltage i.e. at the begining of high tension
transmission system. It can be noted that there is a phase shift of 30° between primary line
voltage and secondary line voltage as leading..
STAR-DELTA CONNECTION:

 In this type of connection, then primary is connected in star fashion while the secondary is
connected in delta fashion as shown in the Fig.

T-T TRANSFORMER CONNECTION:

This type of connection uses tow transformers as that open delta connection. With the help of
this type of connection the conversion from 3-phase is possible which is shown in the Fig. 1.

Fig. 1
 This connection was proposed by Charles F Scott connection. The conversion of 3-phase to
2-phase is also accomplished using this connection.
The Fig.2 shows the details of T -T type of connection. One of the transformers in the
connection is called main transformer which is proved with a 50% taping on both primary and
secondary windings. The other transformer known as teaser transformer having 0.866 tap
connected to centre tap on main transformer on primary and secondary side.

Fig. 2
The teaser transformer may be designed for 86.6 percent of the line or main transformer voltage
but generally is made identical with the main transformer and operated at reduced flux density.
Thus it possible to operate tow identical single phase transformer either in T - T or in open delta
(V-V) if one of the transformers in a delta-delta bank become inoperative. The only thing is that
there should be 50 % tap on one of the transformers.

Fig. 3
The phasor diagram indicating the different voltages is shown in the Fig. 3
From the phasor diagram drawn in the primary side it can be seen that E OY and EOB are each
(VL/2 ) and differ in phase by 180° as both the parts of the windings on the main transformer are
one same magnetic circuit and are connected in opposition. All the sides of the equilateral
triangle represents the line voltage VL. The voltage EOR is the altitude of the equilateral and it will
be equal to (√3/2) times the line voltage and lags behind the voltage across the main transformer
90°. The same relation can be seen in the secondary winding with r - y- b forming a symmetrical
system.