Scribd Logo
Upload

Welcome to Scribd!

  • 146 views

    Digitrim62 Step by Step Calibration

    Uploaded by

    dooman
    1. This document provides instructions for calibrating the tracking and squareness of a cutting machine. 2. The tracking calibration involves feeding paper through the machine and adjusting roller pressure to ensure the cut marks align with the blade edge over at least 20 inches of feed. 3. The square calibration involves adjusting the square correction value in the factory settings menu to align the first cut mark with the blade edge when the paper is fed at an angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Digitrim62 Step by Step Calibration

    Uploaded by

    dooman
    146 views3 pages
    1. This document provides instructions for calibrating the tracking and squareness of a cutting machine. 2. The tracking calibration involves feeding paper through the machine and adjusting roller pressure to ensure the cut marks align with the blade edge over at least 20 inches of feed. 3. The square calibration involves adjusting the square correction value in the factory settings menu to align the first cut mark with the blade edge when the paper is fed at an angle.

    Original Description:

    Fotoba Digitrim 62 Calibration

    Original Title

    Digitrim62_step_by_step_calibration

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. This document provides instructions for calibrating the tracking and squareness of a cutting machine. 2. The tracking calibration involves feeding paper through the machine and adjusting roller pressure to ensure the cut marks align with the blade edge over at least 20 inches of feed. 3. The square calibration involves adjusting the square correction value in the factory settings menu to align the first cut mark with the blade edge when the paper is fed at an angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    146 views3 pages

    Digitrim62 Step by Step Calibration

    Uploaded by

    dooman
    1. This document provides instructions for calibrating the tracking and squareness of a cutting machine. 2. The tracking calibration involves feeding paper through the machine and adjusting roller pressure to ensure the cut marks align with the blade edge over at least 20 inches of feed. 3. The square calibration involves adjusting the square correction value in the factory settings menu to align the first cut mark with the blade edge when the paper is fed at an angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3

    Digitrim 62” Tracking and Square Calibrations

    In order to make these calibrations provide a 50x50 inches sheet (minimum) with printed
    images ( example 8x10). Then follow step by step these instruction:

    1. Turn on the machine


    2. Scan the cut mark and store it in memory (eventually, if different from the previously
    scanned and memorized)
    3. Remove the top aluminium cover of the machine.
    4. Reset the “Angle and Square correction” factory values as follows:
    • press CLR key for few seconds. The Display will show “Factory Setting Menu…”
    • press D/Cut key . The display will show “Square Corr ##.#”
    • press CLR key . The display will show “Square Corr 10.0”
    • press ENT key
    • press Cut key . The display will show “Angle Corr ##.#”
    • press CLR key . The display will show “Angle Corr 10.0”
    • press ENT key

    5. Exit from the factory setting menu by pressing CLR key.


    6. Set the Double Cut at 0 (zero)
    7. Lift the pressure rolls
    8. Insert carefully the paper in the middle of the paper plane.
    9. Align manually the paper so that on both sides the middle of the cut mark
    ( inner white -B- ) will coincide with the blade edge (A)

    BLADE
    PAPER PAPER EDGE A

    PRESSURE
    ROLLS
    TRACKING CALIBRATION

    10. Lower the pressure roller

    11. Feed/forward the paper with the arrows key , (do not use test or start )
    until the next cut mark , check if the second cut mark is still aligned to the blade line.

    12. Repeat same operation until you will have fed at least 20 inches of paper. If after
    feeding there is a misalignment between blades edge and cut mark on one side, for
    more than 1/10” (2,5 mm), the upper roller pressure has to be increased or decreased
    to compensate the error.

    The pressure rollers adjustments is made by setting the pressure of the roll by the
    black set screws inside the metal block as per follow images.

    1 3

    Note: the paper goes more forward where the pressure of the roller is higher (adjust
    accordingly)
    SQUARE CALIBRATION

    13. Once the tracking is ok, realign again the middle white of the first mark to the
    blade’s edge, press then test, check if the blade aligns correctly with the mark. If it
    is not aligned , set the square correction on the Factory Setting Menu:
    • Press CLR for few seconds to access to the factory settings menu
    • Press D/cut key to access to the Square Correction Main Value
    • Modify the square by increasing or decreasing its value until the cut mark
    shall be aligned to the blade.

    14. Once the correction is ok/ in square, try to introduce paper with a small angle (3-4°
    degrees) on both sides ( first right side, second left side).

    If you get under correction / over correction, set it with the “ Angle Correction” from the
    Factory Setting Menu ( “Cut Key” ) ( note: Value is always very close to 10/10.1, never
    more than 2 or 3 decimal points.)

    NOTE:
    When you cut wide paper, the encoder checks the paper feeding and also controls the
    offset between reading and cutting point (DCct). If you cut stripes with small width, the
    encoder shall not check the offset, and it shall be made on a preset number of steps of the
    stepper motor. This could cause to have two different DCct between wide and narrow
    paper. To have the two values coinciding you have available in the factory setting menu
    the Encoder Main/offset adj.
    Please remember that with transparent paper, using the EndP&Auto/Off (under E/P
    menu) the encoders are disabled and can increase the possibilities of errors.

    You might also like