Jura j6 Manual

J6/J600 Instructions for Use
Table of contents
Your J6/J600
Control elements 4
Important information 6
Proper use ...................................................................................................................................................... 6
For your safety ............................................................................................................................................... 6
1 Preparing and using for the first time 10
JURA on the Internet ....................................................................................................................................10
Setting up the machine ..............................................................................................................................10
Filling the bean container ...........................................................................................................................10
Determining the water hardness ..............................................................................................................10
First-time use .................................................................................................................................................11
Connecting milk ...........................................................................................................................................14
Connect accessory (wireless connection) ................................................................................................14
2 Preparation 15
Ways of preparing a beverage ...................................................................................................................15
Ristretto, espresso and coffee ....................................................................................................................16
Two ristretti, two espressi and two coffees .............................................................................................16
Latte macchiato, cappuccino and other speciality coffees with milk .................................................17
Ground coffee ...............................................................................................................................................17
Permanently setting the amount of water for the cup size .................................................................18
Adjusting the grinder ..................................................................................................................................19
Hot water .......................................................................................................................................................19
3 Daily operation 20
Filling the water tank ..................................................................................................................................20
Switching on the machine .........................................................................................................................20
Daily maintenance .......................................................................................................................................21
Regular maintenance ..................................................................................................................................21
Switching off the machine......................................................................................................................... 22
4 Permanent settings in programming mode 23
Adjusting the product settings .................................................................................................................24
Adding products to the start screen, duplicating and personalising ................................................25
Automatic switch-off ..................................................................................................................................26
Energy-saving mode .................................................................................................................................. 27
Setting the water hardness ....................................................................................................................... 27
Display settings ...........................................................................................................................................28
Unit for amount of water ...........................................................................................................................28
Restore factory settings .............................................................................................................................29
Language ......................................................................................................................................................29
Querying information ................................................................................................................................30
5 Maintenance 31
Rinsing the machine ....................................................................................................................................31
Automatic milk system rinsing ................................................................................................................. 32
Cleaning the milk system .......................................................................................................................... 32
2
Table of contents
Dismantling and rinsing the cappuccino frother .................................................................................. 33

Inserting the filter .......................................................................................................................................34
Changing the filter ......................................................................................................................................34
Cleaning the machine ................................................................................................................................ 35
Descaling the machine...............................................................................................................................36
Cleaning the bean container .....................................................................................................................38
Descaling the water tank ...........................................................................................................................39
6 Display messages 40
7 Troubleshooting 41
8 Transport and environmentally friendly disposal 43
Transport / Emptying the system.............................................................................................................43
Disposal.........................................................................................................................................................43
9 Technical data 44
10 Index 45
11 JURA contact details / Legal information 48
Symbol description
Warnings
J WARNING Always take note of any information marked with the words CAUTION or
J CAUTION WARNING and a warning sign. The signal word WARNING draws your attention
to potential serious injury, and the signal word CAUTION to potential minor
injury.
CAUTION CAUTION draws your attention to potential damage to the machine.
Symbols used
T Prompt to take action. This symbol means that you are being prompted to perform
some action.
E Information and tips to make it even easier to use your JURA.
‘Coffee’ Display
3
Control elements
Control elements
11
2
12
13
3
14
4
15
5
16
6
17
8
18
19
9
10
20
1 Filler funnel cover 11 Storage compartment cover

2 Filler funnel for ground coffee 12 Grinder adjustment switch
3 Bean container cover 13 Interchangeable milk spout
4 Water tank cover 14 Storage compartment insert
5 Service socket 15 Milk pipe
6 Bean container with aroma preservation 16 Measuring spoon for ground coffee
cover 17 Mains cable (side of machine)
7 Water tank 18 Hot-water spout
8 Height-adjustable cappuccino frother 19 Height- and width-adjustable coffee spout
9 Coffee grounds container 20 Cup grille
10 Drip tray
4
Control elements
1 2 3
Top of the machine Front

1 On/Off button Q 4 Display
2 Rotary Switch 5 Multi-function buttons (button function
3 P button (programming) depends on what is shown in the display)
Container for milk system cleaning
5
Important information
Proper use The machine is designed and intended for private
domestic use. It should only be used for coffee
preparation and to heat milk and water. Use for any
other purpose will be deemed improper. JURA
Elektroapparate AG cannot accept any responsibil-
ity for the consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty ser-
vice is not applicable for damage or defects caused
by non-compliance with the instructions for use.
Keep these instructions for use close to the machine
and pass them on to the next user.
For your safety Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
J
U Never use a machine which is damaged or has
a defective mains cable.
U In the event of signs of damage, for example if
there is a smell of burning, unplug the machine
immediately from the mains supply and con-
tact JURA service.
U If the mains cable of this machine is damaged,
it must be repaired either directly by JURA or
by an authorised JURA service centre.
U Make sure that the JURA and the mains cable
are not located close to hot surfaces.
U Be careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
6
U Never open and repair the machine yourself.

Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
U To completely and safely disconnect the
machine from the power supply, first switch
off the JURA using the On/Off button. Only
then should you remove the mains plug from
the power socket.
There is a risk of scalds or burns on the spouts and
the cappuccino frother.
U Place the machine out of the reach of children.
U Do not touch any hot parts. Use the handles
provided.
U Ensure that the cappuccino frother is correctly
fitted and clean. If incorrectly fitted or if they
become blocked, the cappuccino frother or its
parts might come off. There is a danger of
parts being swallowed.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
U Never allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
U Protect the JURA from environmental influ-
ences such as rain, frost and direct sunlight.
U Do not immerse the JURA, mains cable or con-
nections in water.
7
U Do not put the JURA or any individual parts in

the dishwasher.
U Switch your JURA off at the power switch
before any cleaning operation. Always wipe
the JURA with a damp cloth rather than a wet
one, and protect it from prolonged exposure
to water splash.
U On models with glass cup grille: Do not sub-
ject the glass cup grille to shock or impact.
U Only connect the machine to the mains volt-
age in accordance with the information on the
rating plate. The rating plate is located on the
underside of your JURA. Further technical data
is provided in these instructions for use (see
Chapter 9 ‘Technical data’).
U Connect the JURA directly to a domestic power
socket. Using multi-socket adapters or exten-
sion cords may cause overheating.
U Please only use original JURA maintenance
products. Use of products that are not explic-
itly recommended by JURA could damage the
machine.
U Do not use alkaline cleaning agents; only use
a soft cloth and mild cleaning agents.
U Do not use any coffee beans treated with addi-
tives or caramelised coffee beans.
U Only fill the water tank with fresh, cold water.
U Switch the machine off at the power switch if
you are going to be absent for a longer period
of time.
U Children may not clean or service the machine
unless supervised by a responsible person.
U Do not allow children to play with the machine.
U Keep children under the age of 8 away from
the machine, or supervise them constantly.
8
U Children aged 8 and over may only operate

the machine without supervision if they have
been instructed in how to use it safely. Chil-
dren must be able to recognise and under-
stand the potential dangers arising from incor-
rect use.
People, including children, who
U do not have the physical, sensory or mental
capabilities to use the machine safely or
U are inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it cor-
rectly.
Safety when handling the CLARIS Smart filter car-
tridge:
U Filter cartridges should be kept out of the
reach of children.
U Store filter cartridges in a dry place in the
sealed packaging.
U Protect cartridges from heat and direct sun-
light.
U Do not use damaged filter cartridges.
U Do not open filter cartridges.
9
1 Preparing and using for the first time
JURA on the Internet Visit us on the Internet. You can download short operating instruc-
tions for your machine from the JURA website (www.jura.com). You
will also find interesting and up-to-date information on your JURA
and on every aspect of coffee.
Setting up the machine When setting up your JURA, please note the following:
U Place the JURA on a horizontal surface that is not sensitive to
water.
U Choose a spot for your JURA which protects the machine
against overheating. Ensure that the ventilation slots are not
covered.
Filling the bean container The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
CAUTION Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean
container.
T Open the bean container cover and remove the aroma

preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
Determining the water When you use the machine for the first time, you must set the water
hardness hardness. If you do not know the hardness of your water, you can
find this out first. Use the Aquadur® test strips supplied with the
machine.
T Hold the test strip briefly (for 1 second) under flowing water.
Shake off the water.
10
T Wait for about 1 minute.

T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
First-time use When using the machine for the first time, you can choose whether
you want to operate JURA with or without the CLARIS Smart filter
cartridge. As well as limescale, the filter cartridge filters many other
substances that impair aroma and flavour out of the water. These
substances may negatively affect the coffee. To enjoy the best qual-
ity coffee at all times, we recommend that you use CLARIS Smart.
J WARNING If the machine is operated with a defective mains cable, there is a

danger of potentially fatal electric shock.
T Never use a machine which is damaged or has a defective
mains cable.
Precondition: The bean container has been filled.

T Insert the mains plug into a power socket.
T Press the On/Off button Q to switch the JURA on.
‘Sprachauswahl’ / ‘Deutsch’
E To view more languages, turn the Rotary Switch.
T Turn the Rotary Switch until the required language is dis-

played, e.g. ‘English’.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display to confirm the setting.
‘Water hardness’
E If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
T Turn the Rotary Switch to change the water hardness set-

ting, e.g. to ‘25 °dH’.
11

‘Saved’ appears briefly on the display.
‘Insert filter’
E Now decide whether you want to operate your JURA with or

without a CLARIS Smart filter cartridge.
Operation with filter cartridge: go straight to the next section.
Operation without filter cartridge: see Chapter 1 ‘Preparing and

using for the first time – First-time use without filter cartridge
activation’.
First-time use with filter

cartridge activation
CAUTION Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Place one receptacle under the hot-water spout and another

under the cappuccino frother.
T Remove the water tank and rinse it with cold water.
T Open the filter holder.
T Fit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge .
T Insert the filter cartridge with its extension into the water
tank.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detects that you have just inserted

the filter cartridge.
‘Filter operation’ / ‘Saved’

‘Filter is being rinsed’, water flows out of the hot-water
spout.
Rinsing of the filter stops automatically after approximately
300 ml.
12
‘System is filling’, water flows out of the cappuccino frother.

‘Empty drip tray’
T Empty the drip tray and put it back into the machine.
T Place a receptacle under the coffee spout.
‘Machine is heating’
‘Machine is rinsing’, the system is rinsed. The rinse stops
automatically. ‘Please select product’ appears on the display.
Your JURA is ready for use.
E The display shows the products you can prepare.

E If the filter is active, this is indicated by a blue filter symbol in
the top right of the display.
First-time use without filter

cartridge activation
T Press the ‘No filter’ button.

‘Descaling mode’ / ‘Saved’
‘Fill water tank’
T Place a receptacle under the cappuccino frother, the coffee
spout and the hot-water spout.

tank.
‘System is filling’, the system fills up with water.
‘Machine is rinsing’, water flows out of the coffee spout. The
rinse stops automatically. Your JURA is ready for use.
E The display shows the products you can prepare.
13
Connecting milk Your JURA creates fine, creamy, feather-light milk foam with a per-
fect consistency. The most important requirement for frothing milk
is a milk temperature of 4–8 °C. We would therefore recommend
using a milk cooler or a milk container.
E Suitable milk containers from JURA are available from special-

ised dealers.
T Remove the protective cover from the cappuccino frother.
T Attach the milk pipe to the cappuccino frother.

T Connect the other end of the milk pipe to a milk container
or a milk cooler.
Connect accessory You have the option of connecting your JURA wirelessly to a
(wireless connection) compatible accessory (e.g. the Cool Control Wireless milk cooler). To
do this, the receiver of the Cool Control or the JURA Smart Connect
must be plugged into the service socket.
T Press the P button.
‘Maintenance status’
T Turn the Rotary Switch until ‘Machine settings’ is displayed.
T Press the Rotary Switch.
‘Choose language’
T Turn the Rotary Switch until ‘Connect accessory’ is dis-
played.
T Press the Rotary Switch to enter the programme item.
‘Connect accessory’
T Press the ‘Next’ button.
T Now follow the instructions on the display to connect the
accessory to the JURA.
14
2 Preparation
2 Preparation
Basic information about preparing drinks:

U During the grinding operation you can select the coffee
strength of single products by turning the Rotary Switch.
U During preparation, you can change the preset amounts (e.g.
amount of water or milk) by turning the Rotary Switch.
U You can stop the machine at any time while a speciality
coffee or hot water is being prepared. To do this, press the
‘  ’ button or the Rotary Switch.
Coffee tastes best served hot. A cold porcelain cup cools the bever-
age – and impairs the taste. We therefore recommend prewarming
the cups. The full coffee aroma can develop only in prewarmed cups.
You can purchase a JURA cup warmer from your specialised dealer.
You can make permanent settings for all products in programming

mode (see Chapter 4 ‘Permanent settings in programming mode –
Adjusting the product settings’).
Ways of preparing a The JURA offers various ways of preparing a speciality coffee, milk or
beverage hot water:
U Preparation using the start screen: Simply press the corre-
sponding preparation button for the product shown on the
display (start screen) that you want.
The following products are displayed as standard:
U ‘Cappuccino’
U ‘Latte macchiato’
U ‘1 portion milk’
U ‘Espresso’
U ‘Coffee’
U ‘Hot water’
U Using the product selector view (Rotary Selection): Only
some of the products you can prepare are shown on the start
screen. As soon as you turn the Rotary Switch, more products
are displayed in a product selector view.
Turn the Rotary Switch to bring the product you want into
focus. Start preparation by pressing the Rotary Switch.
15
2 Preparation
The following additional products are shown in the product

selector view:
U ‘Ristretto’
U ‘Flat White’
U ‘Macchiato’
E The product selector view disappears automatically after
10 seconds if no preparation is started.
E You can move any of the standard products programmed in
your JURA to your preferred position on the start screen or in
the product selector and make it one of your favourites. You
can duplicate and personalise your favourite speciality coffees
by giving them a new product name and individual settings
(e.g. amount and coffee strength) (see Chapter 4 ‘Permanent
settings in programming mode – Adding products to the start
screen, duplicating and personalising’). Please note that the
descriptions provided in the following sections always refer to
the default settings.
Ristretto, espresso and

coffee Example: Proceed as follows to prepare one coffee.
T Place a cup under the coffee spout.
T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the coffee strength are dis-
played. The preset amount of water for coffee flows into the
cup.
Preparation stops automatically. Your JURA is once more
ready for use.
Two ristretti, two To prepare two speciality coffees, press the appropriate preparation
espressi and two coffees button twice (within approximately 2 seconds).
Example: Proceed as follows to prepare two espressi.

T Place two cups under the coffee spout.
T Press the ‘Espresso’ button twice (within 2 seconds) to start
preparation.
‘2 x Espresso’appears and the preset amount of water flows
into the cups.
ready for use.
16
2 Preparation
Latte macchiato, Your JURA prepares latte macchiato, cappuccino, flat white and
cappuccino and other espresso macchiato at the touch of a button. There is no need to
speciality coffees with move the glass or cup.
milk
Example: Proceed as follows to prepare one latte macchiato.
T Place a glass under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the Milk
Foam area 5.
T Press the ‘Latte macchiato’ button.
‘Latte macchiato’appears and the preset amount of milk
flows into the glass.
E There is a short interval while the hot milk separates from the
milk foam. This allows the typical layers of a latte macchiato
to form.
Coffee preparation starts. The preset amount of water for

espresso flows into the glass. Preparation stops automati-
cally. appears on the display. ‘Rinse the milk system’
E 15 minutes after preparation, the milk system is automatically

rinsed (see Chapter 5 ‘Maintenance – Automatic milk system
rinsing’). Therefore always place a receptacle under the cap-
puccino frother after preparing milk.
To ensure that the cappuccino frother always works properly,

you must clean it daily when you have been preparing milk (see
Chapter 5 ‘Maintenance – Cleaning the milk system’).
Ground coffee You can choose to use a second coffee variety, for example decaf-
feinated coffee, with the filter funnel for ground coffee.
E Never add more than two level measuring spoons of ground

coffee.
E Use ground coffee which is not ground too finely. Very fine
coffee can block up the system so that the coffee only comes
out in drips.
E If you did not fill the machine with a sufficient amount of
ground coffee, ‘Not enough ground coffee’ is displayed and
the JURA stops the operation.
17
2 Preparation
E The desired speciality coffee must be prepared within approx-

imately one minute after filling with the ground coffee. Oth-
erwise the JURA stops the operation and is once more ready
for use.
All speciality coffees with ground coffee are always prepared follow-
ing the same model.
Example: Proceed as follows to prepare one espresso using ground

coffee.
T Place an espresso cup under the coffee spout.
T Open the powder chute cover.
‘Please add ground coffee’
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel.
‘Please select product’
T Press the ‘Espresso’ button.
Preparation starts. ‘Espresso’appears and the preset amount
of water for espresso flows into the cup.
ready for use.
Permanently setting the It is easy to permanently adjust the amount of water for all single
amount of water for the products to the cup size. Adjust the amount once as shown in the
cup size following example. Every time you prepare a drink in the future, this
amount will be dispensed.
Example: Proceed as follows to permanently set the amount of

water for one coffee.
T Press and hold the ‘Coffee’ button until ‘Enough coffee?
Press button’ appears.
T Release the ‘Coffee’ button.
Preparation starts and the coffee flows into the cup.
T Press any button as soon as there is sufficient coffee in the
cup.
Preparation stops. ‘Saved’ appears briefly on the display. The
set amount of water for one coffee is permanently stored.
Your JURA is once more ready for use.
18
2 Preparation
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amounts for all single prod-
ucts in programming mode (see Chapter 4 ‘Permanent set-
tings in programming mode – Adjusting the product set-
tings’).
Adjusting the grinder You can adjust the grinder to suit the degree of roast of your coffee.
CAUTION If you adjust the consistency of grind when the grinder is not oper-
ating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is run-
ning.
The consistency of grind is correct if the coffee flows regularly from

the coffee spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind

during the preparation of an espresso.
T Open the storage compartment cover.
T Press the ‘Espresso’ button to start preparation.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The preset amount of water flows into the cup. Preparation
stops automatically.
T Close the storage compartment cover.
Hot water
J CAUTION There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
T Place a cup under the hot-water spout.

T Press the ‘Hot water’ button.
‘Hot water’, the preset amount of water flows into the cup.
Preparation stops automatically. ‘Please select product’
appears on the display.
19
3 Daily operation
3 Daily operation
Filling the water tank Daily maintenance of the machine and hygiene when handling milk,
coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
T Open the water tank cover.

tank.
T Close the water tank cover.
Switching on the Daily maintenance of the machine and hygiene when handling milk,
machine coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
T Press the On/Off button Q to switch the JURA on.
‘Welcome to JURA’
‘Machine is rinsing’, the system is rinsed.
The rinse stops automatically. ‘Please select product’
appears on the display. Your JURA is ready for use.
20
3 Daily operation
Daily maintenance To ensure that you get many years of reliable service out of your
JURA and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
E Always empty the coffee grounds container when the machine

is switched on. This is the only way of resetting the coffee
grounds counter.
T Refit the coffee grounds container and the drip tray.

T Rinse the water tank with clean water.
T Clean the cappuccino frother (see Chapter 5
‘Maintenance – Cleaning the milk system’).
T Remove the milk pipe and rinse it thoroughly under running
water.
T Dismantle and rinse the cappuccino frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the cappuccino
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfibre cloth).
Regular maintenance Carry out the following maintenance actions regularly or as

required:
U In the interests of hygiene, we recommend changing the milk
pipe and interchangeable milk spout on a regular basis
(approximately every 3 months). Replacements are available
from specialised dealers.
U Clean the inside of the water tank, e.g. with a brush. Further
information about the water tank is provided in these instruc-
tions for use (see Chapter 5 ‘Maintenance – Descaling the
water tank’).
U Traces of milk and coffee may stick to the top and bottom of
the cup grille. If this happens, clean the cup grille.
21
3 Daily operation
Switching off the When the JURA is switched off, the system is automatically rinsed if
machine a speciality coffee has been prepared. If milk has been prepared, you
will also be prompted to clean the milk system.
T Place one receptacle under the coffee spout and another
T Press the On/Off button Q.
E If milk has been prepared, you will be prompted to clean the

milk system (‘Clean the milk system’). After 10 seconds the
switch-off process continues automatically.
If milk has been prepared but you have not started milk sys-
tem cleaning, the milk system is rinsed first (‘Milk system is
being rinsed’).
‘Machine is rinsing’, the system rinses itself.The operation
stops automatically.Your JURA is switched off.
22
4 Permanent settings in programming mode
Press the P button to enter programming mode. You can navigate

through the programme items and permanently save the required
settings simply by turning the Rotary Switch and using the multi-
function buttons. The following settings can be made:
Programme item Sub-item Explanation
‘Maintenance ‘Clean’, T Here you can start the required maintenance
status’ ‘Change the filter’ (only if programme or find out what maintenance
filter is fitted), actions are required.
‘Descale’,
‘Clean the milk system’,
‘Rinse’,
‘Maintenance information’
‘Product settings’ ‘Expert mode’ T Select your settings for speciality coffees and
hot water.
‘Classics’ T Replace the products on the start screen and
in the product selector with your favourites.
Duplicate and personalise your favourite
speciality coffees by giving them a new
product name and individual settings.
‘Machine settings’ ‘Choose language’ T Select your language.
‘Switch off after’ T Set the time after which the JURA should
switch off automatically.
‘Save energy’ T Select an energy-saving mode.
‘Factory setting’ T Reset the machine to its factory setting.
‘Units’ T Select the unit for the amount of water.
‘Display’ T Change the display settings.
‘Water hardness’ T Adjust the water hardness.
‘Product counter’, T Keep track of all products prepared and view
‘Maintenance counter’ the number of maintenance programmes
performed.
‘Version’ Software version
‘Connect accessory’, T Connect the machine wirelessly to a JURA
‘Disconnect accessories’ accessory or disconnect the connection again.
(Only displayed if the JURA Smart Connect is
being used.)
23
Adjusting the product In the programme item ‘Product settings’ / ‘Expert mode’ you can
settings make individual settings for all speciality coffees and hot water. The
following permanent settings can be made:
Product Coffee Amount More settings
strength
Ristretto, 10 levels Coffee: 15 ml – 80 ml Temperature (low, normal, high),
espresso Product name
Coffee 10 levels Coffee: 25 ml – 240 ml Temperature (low, normal, high)
Two ristretti, – Coffee: the amount set for Temperature (as for single product),
two espressi, the single product is Product name
two coffees doubled.
Latte macchiato 10 levels Coffee: 25 ml – 240 ml Temperature (low, normal, high),
Milk: 0 sec. – 120 sec. Product name
Interval: 0 sec. – 60 sec.
Cappuccino, 10 levels Coffee: 25 ml – 240 ml Temperature (low, normal, high),
flat white Milk: 0 sec. – 120 sec. Product name
Espresso 10 levels Coffee: 15 ml – 80 ml Temperature (low, normal, high),
macchiato Milk: 0 sec. – 120 sec. Product name
Interval: 0 sec. – 60 sec.
Portion of milk – Milk: 0 sec. – 120 sec. Product name
Hot water – Water: 25 ml – 450 ml Temperature (low, normal, high),
Product name
Permanent settings in programming mode always follow the same

model.
Example: Proceed as follows to change the amount of water and
coffee strength for one espresso.
T Turn the Rotary Switch until ‘Product settings’ is displayed.
‘Expert mode’
‘Expert mode’
T Press the ‘Espresso’ button.
‘Expert mode’ / ‘Espresso’
‘Espresso’
24
T Turn the Rotary Switch to change the coffee strength set-

ting.
T Press the Rotary Switch to confirm the setting.
T Turn the Rotary Switch until the fill volume is in focus.
T Turn the Rotary Switch to change the fill volume setting.
T Press the Rotary Switch to confirm the setting.
‘Expert mode’ / ‘Espresso’
T Press the P button to exit programming mode.
Adding products to the In the programme item ‘Product settings’ / ‘Classics’ you will find all
start screen, duplicating the products stored as standard in your JURA. You can move any of
and personalising these products to your preferred position on the start screen or in
the product selector and make it one of your favourites. You can
duplicate and personalise your favourite speciality coffees by giv-
ing them a new product name and individual settings (e.g. amount
and coffee strength).
Example: Proceed as follows to replace ‘Latte macchiato’ on the

start screen with ‘Macchiato’.
T Turn the Rotary Switch until ‘Product settings’ is displayed.
‘Expert mode’
T Turn the Rotary Switch until ‘Classics’ is displayed.
‘Add to favourites’
T Press the Rotary Switch again.
T Turn the Rotary Switch until ‘Macchiato’ is in focus.
‘Select position’
T Press the ‘Latte macchiato’ button.
‘Macchiato’ / ‘Do you want to replace the current product?’
T Press the ‘Yes’ button.
‘Product name’
25
E You can now give the product you just added a new name.

‘Macchiato’
E You can now change various settings for the product. To do

this, briefly press the Rotary Switch to access the various
setting options. Confirm the settings by pressing the
‘Save’ button.
E If you do not want to change any more settings, just press the
‘  ’ button.
Automatic switch-off By instructing your JURA to automatically switch itself off, you can
cut down your energy consumption. If this function is activated,
your JURA switches off automatically after the preset time following
the last action on the machine.
You can set the automatic switch-off to 15 minutes, 30 minutes or

1-9 hours.
T Turn the Rotary Switch until ‘Switch off after’ is displayed.
‘Switch off after’
T Turn the Rotary Switch to change the switch-off time.
‘Switch off after’
26
Energy-saving mode In the programme item ‘Machine settings’ / ‘Save energy’ you
can permanently set an energy-saving mode (Energy Save Mode,
E.S.M.©):
U ‘Active’
U Soon after the last preparation, the JURA stops heating up.
After about 5 minutes the message ‘Energy Save’ is dis-
played.
U Before you can prepare a speciality coffee, speciality coffee
with milk, or hot water, the machine must heat up.
U ‘Inactive’
U All speciality coffees, speciality coffees with milk and hot
water can be prepared without having to wait.
Example: Proceed as follows to change the energy-saving mode

from ‘Active’ to ‘Inactive’.
T Turn the Rotary Switch until ‘Save energy’ is displayed.
‘Save energy’
T Turn the Rotary Switch until ‘Inactive’ is displayed.
‘Save energy’
Setting the water The harder the water is, the more frequently the JURA needs to
hardness be descaled. It is therefore important to set the water hardness
accurately.
The water hardness was set when the machine was first used. You
can change this setting at any time.
The water hardness can be adjusted on a continuous scale between

1 °dH and 30 °dH.
27

T Turn the Rotary Switch until ‘Water hardness’ is displayed.
T Turn the Rotary Switch to change the setting.
Display settings In the programme item ‘Machine settings’ / ‘Display’ you can set the
display brightness (as a percentage).
T Turn the Rotary Switch until ‘Display’ is displayed.
‘Display’
T Turn the Rotary Switch to change the setting.
‘Display’
Unit for amount of water In the programme item ‘Machine settings’ / ‘Units’ you can select
the unit used for the amount of water.
Example: Proceed as follows to change the unit for the amount of

water from ‘ml’ to ‘oz’.
T Turn the Rotary Switch until ‘Units’ is displayed.
28

‘Units’
T Turn the Rotary Switch until ‘oz’ is displayed.
‘Units’
Restore factory settings In the programme item ‘Machine settings’ / ‘Factory setting’ the
machine can be reset to its factory setting: All user settings (apart
from the ‘filter’ and ‘water hardness’) are reset to factory settings.
Your JURA then switches off.
T Turn the Rotary Switch until ‘Factory setting’ is displayed.
‘Factory setting’ / ‘Reset the machine to the factory set-
tings?’
T Press the ‘Yes’ button.
Your JURA is switched off.
Language In this programme item you can set the language used by your
JURA.
Example: Proceed as follows to change the language from ‘English’

to ‘Deutsch’.
T Turn the Rotary Switch until ‘Deutsch’ is displayed
29

‘Gespeichert’ appears briefly on the display.
‘Sprachauswahl’
‘Bitte wählen’
Querying information In the programme item ‘Machine settings’ you can view the follow-
ing information:
U ‘Product counter’: Number of prepared speciality coffees, milk
and hot water
U ‘Maintenance counter’: Number of maintenance programmes
performed (cleaning, descaling etc.)
U ‘Version’: Software version
Example: Proceed as follows to view the number of speciality cof-

fees prepared.
T Turn the Rotary Switch until ‘Product counter’ is displayed.
‘Product counter’
E Turn the Rotary Switch to view the number of other speciality

coffees.
30
5 Maintenance
5 Maintenance
Your JURA has the following integrated maintenance programmes:

U Rinsing the machine
U Rinsing the milk system in the dual spout
U Cleaning the milk system in the dual spout (‘Clean the milk
system’)
U Changing the filter (‘Change the filter’)
(only if filter is activated)
U Cleaning the machine (‘Clean’)
U Descaling the machine (‘Descale’)
(only if filter is not activated)
E Clean or descale the machine, rinse the milk system or change

the filter when you are prompted to do so.
E Press the P button to view a list of the maintenance pro-
grammes (‘Maintenance status’). When the bar is completely
filled with red, your JURA will prompt you to perform the
appropriate maintenance programme.
E In the interests of hygiene, you should clean the milk system
daily when you have been preparing milk.
Rinsing the machine

You can initiate the rinse operation manually at any time.
‘Clean’
T Turn the Rotary Switch until ‘Rinse’ is displayed.
T Press the Rotary Switch to initiate the rinse operation.
‘Machine is rinsing’, ‘Milk system is being rinsed’, water
flows out of the coffee spout.
The rinse stops automatically. ‘Please select product’
appears on the display.
31
5 Maintenance
Automatic milk system 15 minutes after milk preparation, the milk system is automatically
rinsing rinsed. Therefore always place a receptacle under the cappuccino
frother after preparing milk.
When ‘Rinse the milk system’ is displayed, you can start rinsing by
pressing the Rotary Switch.
Cleaning the milk system To ensure that the cappuccino frother always works properly, you
must clean it daily when you have been preparing milk
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
E JURA milk system cleaner is available from specialised dealers.

E To clean the milk system, use the container supplied.

‘Clean’
T Turn the Rotary Switch until ‘Clean the milk system’ is dis-
played.
‘Clean the milk system’
T Press the Rotary Switch again.
T Press the ‘Start’ button.
T Remove the milk pipe from the milk container or carton.
T Add milk system cleaner to the front part of the container
up to the bottom mark (indicated by 6).
T Then fill with water up to the upper mark.
T Place the container under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the Milk
position z.
6
32
5 Maintenance
T Connect the milk pipe to the container.
E To connect the milk pipe to the container correctly, the pipe

must be fitted with a connector.

‘Milk system is being cleaned’ appears and the cappuccino
6
frother and the milk pipe are cleaned.

T During the first brief interruption, set the setting wheel of
the cappuccino frother to the Milk Foam position 5.
‘Water for cleaning milk system’
T Rinse the container thoroughly and fill the front part with
fresh water up to the upper mark.
T Place this under the cappuccino frother and reconnect the
milk pipe to the container.
‘Milk system is being cleaned’ appears and the cappuccino
frother and the milk pipe are rinsed with fresh water.
The start screen is displayed.
Dismantling and rinsing To make sure the cappuccino frother works properly, and in the
the cappuccino frother interests of hygiene, it must be dismantled and rinsed daily if you
have been preparing milk.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Carefully pull the cappuccino frother down and off.
T Dismantle the cappuccino frother into its individual parts.
T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250 ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
T Reassemble the cappuccino frother.
E Ensure that all individual parts are correctly and firmly con-
nected to ensure correct operation of the cappuccino frother.
T Firmly attach the frother to the connector.
33
5 Maintenance
Inserting the filter Your JURA no longer has to be descaled if you are using the CLARIS
Smart filter cartridge. If you did not insert the filter cartridge the first
time you used the machine, you can do this now as follows.
T Place a receptacle under the hot-water spout.
T Remove and empty the water tank.
T Open the filter holder.
T Fit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge .
tank.
tank.
E The machine automatically detects that you have just inserted

‘Filter operation’ / ‘Saved’

spout.
Rinsing of the filter stops automatically after approximately
300 ml.
‘Filter operation’, ‘Filter rinsing complete’
‘Please select product’ appears on the display. Your JURA is
once more ready for use.
Changing the filter E Once the filter cartridge stops working (depending on the
water hardness setting), the JURA will prompt you to change
the filter.
E CLARIS Smart filter cartridges are available from specialised
dealers.
Precondition: ‘Change filter’ is displayed.
34
5 Maintenance
T Place a receptacle under the hot-water spout.

T Open the filter holder and remove the old CLARIS Smart
filter cartridge and filter extension.
T Fit the filter cartridge extension on top of a new CLARIS filter
cartridge Smart.
tank.
tank.
E The machine automatically detects that you have just changed

‘Change the filter’ / ‘Saved’

spout.
‘Change the filter’, ‘Filter rinsing complete’
‘Please select product’ appears on the display. Your JURA is
once more ready for use.
Cleaning the machine After 180 preparations or 80 switch-on rinses, the JURA will prompt
you to clean it.
CAUTION If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
E The cleaning programme lasts approximately 20 minutes.

E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from specialised dealers.
Precondition: ‘Clean machine’ is displayed.

‘Clean’
35
5 Maintenance

T Press the ‘Start’ button again.
‘Empty coffee grounds container’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Press the Rotary Switch’
T Place one receptacle under the coffee spout and another
‘Machine is being cleaned’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
‘Machine is being cleaned’, water flows repeatedly out of the
coffee spout and the cappuccino frother.
The operation stops automatically.
‘Empty coffee grounds container’
Cleaning is now complete. The start screen is displayed.
Descaling the machine The JURA builds up deposits of limescale over time and automati-
cally prompts you to descale it when necessary. The degree of calci-
fication depends on the hardness of your water.
E If you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
J CAUTION If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
36
5 Maintenance
CAUTION If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
CAUTION If the descaling operation is interrupted, there may be damage to

the machine.
T Allow the descaling programme to run to the end.
CAUTION If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approximately 45 minutes.

E JURA descaling tablets are available from specialised dealers.
Precondition: ‘Decalcify machine’ is displayed.

‘Descale’
T Press the ‘Start’ button again.
‘Pour descaling agent into water tank’
T Completely dissolve 3 JURA descaling tablets in a receptacle
holding 500 ml of water. This may take several minutes.
T Pour the solution into the empty water tank and insert it
into the machine.
T Place one receptacle under the hot-water spout and another

‘Machine is being descaled’ appears and water flows repeat-
edly out of the hot-water spout and the cappuccino frother.
The operation is interrupted, ‘Empty drip tray’.
37
5 Maintenance
T Remove the water tank and rinse it thoroughly.
tank.
T Place a receptacle under the cappuccino frother, the coffee
spout and the hot-water spout.
‘Machine is being descaled’, The descaling operation is
continued.
The operation is interrupted, ‘Empty drip tray’.
Descaling is now complete. The start screen is displayed.
E If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.
Cleaning the bean Coffee beans may be covered with a slight oil film which remains on
container the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition: ‘Fill bean container’ is displayed.

T Switch the machine off with the On/Off button Q.
T Open the bean container cover and remove the aroma
preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
38
5 Maintenance
Descaling the water tank Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLARIS Smart filter cartridge, remove this.
T Completely fill the water tank and dissolve 3 JURA descaling
tablets in it.
T Leave the water tank with the descaling solution for several
hours (e.g. overnight).
T Empty the water tank and rinse it thoroughly.
T If you use a CLARIS Smart filter cartridge, insert this again.
tank.
39
6 Display messages
6 Display messages
Message Cause/Result Action

‘Fill water tank’ The water tank is empty. You T Fill the water tank (see Chapter 3 ‘Daily
cannot prepare any products. operation – Filling the water tank’).
‘Empty coffee The coffee grounds container is T Empty the coffee grounds container
grounds full. You cannot prepare any and the drip tray (see Chapter 3 ‘Daily
container’ products. operation – Daily maintenance’).
‘Drip tray not The drip tray is not inserted T Fit the drip tray.
fitted’ correctly or is not inserted at all.
You cannot prepare any products.
‘Fill bean The bean container is empty. You T Fill the bean container (see Chapter 1
container’ cannot prepare any speciality ‘Preparing and using for the first time –
coffees, but you can prepare hot Filling the bean container’).
water and milk.
‘Rinse the milk The JURA requests a milk system T Press the Rotary Switch to start rinsing
system’ rinse. or wait 15 minutes until rinsing starts
automatically (see Chapter 5 ‘Mainte-
nance – Automatic milk system rinsing’).
‘Change filter’ The filter cartridge no longer T Replace the CLARIS Smart filter
works. The JURA is prompting a cartridge (see Chapter 5 ‘Maintenance –
filter change. Changing the filter’).
‘Clean machine’ The JURA is prompting you to T Perform cleaning (see Chapter 5
clean it. ‘Maintenance – Cleaning the machine’).
‘Decalcify The JURA is prompting you to T Perform descaling (see Chapter 5
machine’ descale it. ‘Maintenance – Descaling the machine’).
‘Not enough There is insufficient ground coffee T The next time you prepare a beverage,
ground coffee’ in the machine; the JURA stops the add more ground coffee (see Chapter 2
operation. ‘Preparation – Ground coffee’).
‘Machine too The system is too hot to start a T Wait for several minutes until the
hot for maintenance programme. system has cooled or prepare a
maintenance’ speciality coffee or hot water.
40
7 Troubleshooting
7 Troubleshooting
Problem Cause/Result Action

Insufficient foam is The cappuccino frother is T Clean the cappuccino frother (see
produced when the dirty. Chapter 5 ‘Maintenance – Cleaning the
milk is frothed or milk milk system’).
sprays from the T Dismantle and rinse the cappuccino
cappuccino frother. frother (see Chapter 5 ‘Maintenance –
Dismantling and rinsing the cappuccino
frother’).
Coffee only comes out The coffee is ground too T Set the grinder to a coarser setting (see
in drips when it is being finely and obstructs the Chapter 2 ‘Preparation – Adjusting the
prepared. system. The water grinder’).
hardness may not have T Perform descaling (see Chapter 5
been correctly set. ‘Maintenance – Descaling the machine ’).
‘Fill water tank’ is The water tank float is T Descale the water tank (see Chapter 5
displayed although the trapped. ‘Maintenance – Descaling the water
water tank is full. tank’).
Little or no water or The connector of the T Remove the cappuccino frother.
steam comes out of the cappuccino frother may be T Unscrew the black connector with the
cappuccino frother. The blocked by milk residues or aid of the hexagonal hole on the
pump is very quiet. limescale fragments measuring spoon for ground coffee.
loosened during descaling. T Clean the connector thoroughly.
T Screw the connector back on by hand.
T Carefully tighten it using the hexagonal
hole on the measuring spoon, turning by
no more than a quarter of a rotation.
Grinder is making a There are foreign objects in T Contact customer support in your
very loud noise. the grinder. country (see Chapter 11 ‘JURA contact
details / Legal information’).
‘Error 2’ or ‘Error 5’ is If the machine has been T Warm the machine at room
displayed. exposed to the cold for a temperature.
long period of time,
heating may be disabled
for safety reasons.
41
7 Troubleshooting
Problem Cause/Result Action

Other ‘Error’ messages – T Switch the JURA off with the On/Off
are displayed. button Q. Contact customer support in
your country (see Chapter 11 ‘JURA
contact details / Legal information’).
E If you were unable to solve the problem, contact customer

support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
42
8 Transport and environmentally friendly disposal
8 Transport and environmentally friendly disposal
Transport / Emptying the Keep the packaging for your JURA. It should be used to protect the
system machine during transport.
In order to protect the JURA from frost during transport, the system
must be emptied.
T Remove the milk pipe from the cappuccino frother.
T Place a receptacle under the cappuccino frother.
T Turn the Rotary Switch until ‘1 portion milk’ is in focus.
‘1 portion milk’ appears and hot steam is discharged from
the cappuccino frother.
T Turn the Rotary Switch until ‘60 sec.’ is displayed.
Steam will continue to be discharged from the cappuccino
frother until the system is empty.
T Press the On/Off button Q.
Your JURA is switched off.
Disposal Please dispose of old machines in an environmentally neutral way.

H
Old machines contain valuable, recyclable materials which should
be recycled. Please therefore dispose of old machines via suitable
collection systems.
43
9 Technical data
9 Technical data
Voltage 220–240 V ~, 50 Hz
Power 1450 W
Conformity mark A
Energy consumption approx. 6 Wh
‘Save energy’ / ‘Active’
Energy consumption approx. 11 Wh
‘Save energy’ / ‘Inactive’
Pump pressure static, max. 15 bar
Holding capacity of water tank 2.1 l
Holding capacity of bean container 250 g
Holding capacity of coffee grounds max. 16 portions
container
Cable length approx. 1.1 m
Weight 10.7 kg
Dimensions (W × H × D) 28.5 × 34.2 × 43.3 cm
44
10 Index
10 Index
A Cover
Adding products to the start screen 25 Bean container 4
Addresses 48 Filler funnel for ground coffee 4
Adjusting the product settings 24 Storage compartment 4
Aroma preservation cover Water tank 4
Bean container with aroma preservation Cup grille 4
cover 4 Customer support 48
Automatic switch-off 26
D
B Daily maintenance 21
Bean container Descaling
Bean container with aroma preservation Machine 36
cover 4 Water tank 39
Cleaning 38 Dismantling
Filling 10 Cappuccino frother 33
Bus bar Dismantling and rinsing
Technical data 44 the cappuccino frother 33
Button Display 5
On/Off button 5 Display messages 40
P button (programming) 5 Display settings 28
Disposal 43
C Double product 16
Caffè latte 17 Drip tray 4
Cappuccino 17
Cappuccino frother cleaning E
Cleaning the milk system 32 Emptying the system 43
Changing the product assigned to a button Energy-saving mode 27
25 Errors
CLARIS Smart filter cartridge Troubleshooting 41
Change 34 Espresso 16
Insert 34 Two espressi 16
Cleaning Espresso macchiato 17
Bean container 38 F
Machine 35 Factory settings
Coffee 16 Restore factory settings 29
Two coffees 16 Filler funnel
Coffee grounds container 4 Filler funnel for ground coffee 4
Coffee spout Filling
Height- and width-adjustable coffee Bean container 10
spout 4 Water tank 20
Connect accessory 14 Filter
Consistency of grind Change 34
Adjusting the grinder 19 Insert 34
Grinder adjustment switch 4 First-time use 11
Contact details 48 With filter cartridge activation 12
Without filter cartridge activation 13
45
10 Index
Flat white 17 Milk system

Frother Cleaning 32
Cappuccino frother 4 Milk system rinsing 32
G P
Grinder adjustment switch 4 Permanently setting the water for the cup
Ground coffee 17 size 18
Measuring spoon for ground coffee 4 Permanent settings in programming mode
23
H Personalising products 25
Homepage 10 Preparation 15, 17
Hotline 48 At the touch of a button 15
Hot water 19
Caffè latte 17
Hot-water spout 4
Cappuccino 17
I Coffee 16
Instant coffee Espresso 16
Ground coffee 17 Espresso macchiato 17
Interchangeable milk spout 4 Flat white 17
Internet 10 Ground coffee 17
J Hot water 19
JURA Latte macchiato 17
Contact details 48 Ristretto 16
Internet 10 Two coffees 16
Two espressi 16
L Two ristretti 16
Language 29
Two speciality coffees 16
Latte macchiato 17
Using the product selector 15
M Preparation options 15
Machine Problems
Cleaning 35 Troubleshooting 41
Daily maintenance 21 Product selector view 15
Descaling 36 Product settings
Regular maintenance 21 Adjusting 24
Rinsing 31 Programming mode 23
Setting up 10 Adding products to the start screen 25
Switching off 22 Automatic switch-off 26
Switching on 20 Display settings 28
Mains cable 4 Duplicating products 25
Maintenance 31 Energy-saving mode 27
Daily maintenance 21 Language 29
Regular maintenance 21 Querying information 30
Measuring spoon for ground coffee 4 Restore factory settings 29
Messages, display 40 Setting the water hardness 27
Milk Unit for amount of water 28
Connecting milk 14 Proper use 6
Milk spout 4
46
10 Index
Q
Querying information 30
R
Regular maintenance 21
Rinsing
Machine 31
Ristretto 16
Two ristretti 16
Rotary Selection 15
Rotary Switch 5
S
Safety 6
Safety information 6
Service socket 4
Settings
Permanent settings in programming
mode 23
Setting up
Setting up the machine 10
Short operating instructions 10
Spout
Hot-water spout 4
Switching off 22
Switching on 20
Switch-off
Automatic switch-off 26
Symbol description 3
T
Technical data 44
Tel 48
Transport 43
Troubleshooting 41
Two products 16
U
Unit for amount of water 28
Use, First-time 11
W
Water hardness
Determining the water hardness 10
Setting the water hardness 27
Water tank 4
Descaling 39
Filling 20
Website 10
Wireless connection 14
47
J72926/J6-J600/en/201608
11 JURA contact details / Legal information
11 JURA contact details / Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 (0)62 38 98 233
@ You will find additional contact details for your country at

www.jura.com.
Directives The machine complies with the following directives:

U 2014/35/EU – Low Voltage Directive
U 2014/30/EU – Electromagnetic Compatibility
U 2009/125/EC – Ecodesign Directive
U 2011/65/EU – RoHS Directive
Technical changes We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine. Some details of
your JURA may vary.
Feedback Your opinion is important to us! Use the contact details at

www.jura.com.
Copyright The instructions for use contain information which is protected by

copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
48

Jura j6 Manual

Uploaded by

Copyright:

Available Formats

Jura j6 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jura j6 Manual

Uploaded by

Copyright:

Available Formats

J6/J600 Instructions for Use

Dismantling and rinsing the cappuccino frother .................................................................................. 33

1 Filler funnel cover 11 Storage compartment cover

Top of the machine Front

Container for milk system cleaning

U Never open and repair the machine yourself.

U Do not put the JURA or any individual parts in

U Children aged 8 and over may only operate

1 Preparing and using for the first time

T Open the bean container cover and remove the aroma

T Wait for about 1 minute.

J WARNING If the machine is operated with a defective mains cable, there is a

Precondition: The bean container has been filled.

E To view more languages, turn the Rotary Switch.

T Turn the Rotary Switch until the required language is dis-

T Turn the Rotary Switch to change the water hardness set-

T Press the ‘Save’ button.

E Now decide whether you want to operate your JURA with or

Operation with filter cartridge: go straight to the next section.

Operation without filter cartridge: see Chapter 1 ‘Preparing and

First-time use with filter

T Place one receptacle under the hot-water spout and another

E The machine automatically detects that you have just inserted

‘Filter operation’ / ‘Saved’

‘System is filling’, water flows out of the cappuccino frother.

E The display shows the products you can prepare.

First-time use without filter

T Press the ‘No filter’ button.

T Remove the water tank and rinse it with cold water.

E The display shows the products you can prepare.

E Suitable milk containers from JURA are available from special-

T Remove the protective cover from the cappuccino frother.

T Attach the milk pipe to the cappuccino frother.

Basic information about preparing drinks:

You can make permanent settings for all products in programming

The following additional products are shown in the product

Ristretto, espresso and

Example: Proceed as follows to prepare two espressi.

Coffee preparation starts. The preset amount of water for

E 15 minutes after preparation, the milk system is automatically

To ensure that the cappuccino frother always works properly,

E Never add more than two level measuring spoons of ground

E The desired speciality coffee must be prepared within approx-

Example: Proceed as follows to prepare one espresso using ground

Example: Proceed as follows to permanently set the amount of

The consistency of grind is correct if the coffee flows regularly from

Example: Proceed as follows to change the consistency of grind

T Place a cup under the hot-water spout.

T Open the water tank cover.

E Always empty the coffee grounds container when the machine

T Refit the coffee grounds container and the drip tray.

Regular maintenance Carry out the following maintenance actions regularly or as

E If milk has been prepared, you will be prompted to clean the

4 Permanent settings in programming mode

Press the P button to enter programming mode. You can navigate

Permanent settings in programming mode always follow the same

T Turn the Rotary Switch to change the coffee strength set-

Example: Proceed as follows to replace ‘Latte macchiato’ on the

T Press the ‘Save’ button.

E You can now change various settings for the product. To do