WARNING

Please install the antenna (connect to the location “B” on the back panel of the radio) and set the SWR (Standing Wave
Ratio) before transmitting. )DLOXUHWRGRVRPD\UHVXOWLQGHVWUXFWLRQRIWKHSRZHUDPSOL¿HUZKLFKLVQRWFRYHUHGE\WKH
guarantee.

WELCOME TO USE
AT-310M is a Multi-norms and multi-function CB radio which provides you with top performance.
With the use of SMT technology to guarantee the best stability, reliability and unprecedented quality, AT-310M is a new
step in personal communication and is surely the best choice for professional users of CB radios.0RUHRYHULWDGRSWVÀDVK
CPU in the radio, which makes AT-310M ready for future upgrading and functions expanding.To ensure that you use the
radio to the fullest, please read this manual carefully before installing.

RESET
-Hold key (7) [ CH9/19 ] to power on, the radio will reset, all channel data will resume factory default setting.
 CONTENTS
INSTALLATION..................................................................................................................................................................................1
WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO ..................................................................................................................1
ANTENNA INSTALLATION .................................................................................................................................................................1
POWER CONNECTION.....................................................................................................................................................................2
BASIC OPERATIONS ........................................................................................................................................................................2
ADJUSTMENT OF SWR(standing wave ratio) ......................................................................................................................................2

HOW TO USE YOUR CB RADIO ......................................................................................................................................................4

ON/OFF-VOLUME ............................................................................................................................................................................4

MANUAL SQUELCH .........................................................................................................................................................................4

AUTOMATIC SQUELCH ....................................................................................................................................................................4

CHANNEL SELECTION .....................................................................................................................................................................4

MODULATION MODE SELECTION ....................................................................................................................................................4

NORM SELECTION ..........................................................................................................................................................................4

AUTOMATIC SCANNING ...................................................................................................................................................................4

PRIORITY CHANNEL9/19..................................................................................................................................................................5

TRANSMITTING ...............................................................................................................................................................................5

EXTERNAL SPEAKER JACK .............................................................................................................................................................5

TECHNICAL CHARACTERISTICS ...................................................................................................................................................6

INSTALLATION 2. ANTENNA INSTALLATION
1. WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO a) )Choosing antenna:
a)You should choose the most appropriate setting from a simple and -For CB radios, the longer the antenna, the better its results. Your
practical point of view dealer will help you with your choice of antenna.
b) Your CB radio should not interfere with the driver or the b) Mobile antenna:
passengers. 0XVWEH¿[HGWRWKHYHKLFOHZKHUHWKHUHLVDPD[LPXPRIPHWDOOLF
c) Remember to provide different wires for the passing and protection surface(ground plane) , away from windscreen mountings.
(e.g. power, antenna, accessory cabling) so that they do not in any -If you already have a radio-telephone antenna installed, the CB
way interfere with the driving of vehicles. antenna should be higher than this.
d) To install your equipment, use the cradle (H) and the self-tapping
screws [E] provided (drilling diameter 4 mm). Take care not to -There are two types of antenna: Pre-regulated antenna which should
damage the vehicle’s electrical system while drilling the dash be used on a good ground plane (e.g. car roof or lid of the boot), and
board. adjustable antenna which offer a much larger frequency range and
e) Do not forget to insert the rubber joints [G] between the CB and can be used on a smaller ground plane.
its support as these have a shock-absorbing effect which permits )RUDQDQWHQQDZKLFKPXVWEH¿[HGE\GULOOLQJ\RXZLOOQHHGDJRRG
gentle orientation and tightening of the set. contact between the antenna and the ground plane. To obtain this,
f) Choose where to place the microphone support and remember that you should lightly scratch the surface where the screw and tightening
the microphone cord must stretch to the driver without interfering star are to be placed.
with the controls of the vehicle. %HFDUHIXOQRWWRSLQFKRUÀDWWHQWKHFRD[LDOFDEOH DVWKLVUXQVWKH 1
G)As the transceiver has a frontal microphone socket, it can be set risk of break down and/or short circuiting).
into the dash board. You will need to add external loud speaker -Connect the antenna to location (B).
to improve the sound quality of communications(connector ext. c) Fixed antenna:
SP situated on the back panel: D). Ask your dealer for advice on
mounting your CB radio. A fixed antenna should be installed in a space as spacious as
possible. ,ILWLVQHFHVVDU\IRU\RXWR¿[WKHDQWHQQDWRDPDVW\RX
E need to keep it as per the requirements of the laws in force (please
E
H E turn to professional advice).
E
H
F
F
G
G
CH
CH
D

B
C
OUTPUT RADIUS PATTERNS
 3. POWER CONNECTION 4. BASIC OPERATIONS
This is protected against an inversion of polarities. However, before a) Connect the microphone
switching it on, you are advised to check all the connections. Your b) Check the antenna connections
equipment must be supplied with a continued current of 12 volts (A). c) Turn the set on by turning the volume knob clockwise
Today, most cars and lorries are negative earth. You can check this by d) Turn the squelch knob to minimum(Full-anti clockwise)
making sure that the negative terminal of the battery is connected either e) Adjust the volume to a comfortable level
to the engine block or to the chassis. If this is not the case, you should f) Go to channel 20 EC by using either the [ ] or[ ] key.
consult your dealer.
5. ADJUSTMENT OF SWR(standing wave ratio)
WARNING: Lorries generally have two batteries to supply a voltage of 24
volts, in which case it will be necessary to insert a 24/12 volt converter WARNING: This must be carried out when you use your CB radio
into the electrical circuit. The following connection steps should be for the first time (and whenever you re-position your antenna). The
carried out with the power cable disconnected from the set. adjustment must be carried out in an obstacle-free area.
a)Check whether the battery is of 12 volts. ὉAdjustment should be operated with external SWR meter.
b) Locate the positive and negative terminals of the battery ( is
red and is black). Should it be necessary to lengthen the power a)To connect the SWR meter
cable, please use the same or a superior type of cable. Connect the SWR meter between the CB radio and the antenna
c) It is necessary to connect your CB to a permanent ( ) and ( ). as close as possible to the CB radio (use a maximum of 40cm
We advise you to connect the power cable directly to the battery cable)
2 (as the connection of the CB cable to the wiring of the car-radio or b) To adjust the SWR meter
other parts of the electrical circuit may, in some cases, increase the -Set the CB to channel 20@EC band in FM
possibilities of interference). -put the switch on the SWR meter to position CAL or FWD
d) Connect the red wire ( ) to the positive terminal of the battery and -Press the <<Push-To-Talk>> switch on the microphone to transmit
the black ( ) wire to the negative terminal of the battery. %ULQJWKHLQGH[QHHGOHWRźE\XVLQJWKHFDOLEUDWLRQNH\
e) Connect the power cable to your CB radio. - Change the switch to position SWR (reading of the SWR level)
The reading on the meter should be as near as possible to 1. If
WARNING:Never replace the original fuse (5A) by one of a different this is not the case, re-adjust your antenna to obtain a reading
value. as close as possible to 1.( An SWR reading between 1 and 1.8 is
acceptable).
-It will be necessary to re-calibrate the SWR meter after each
adjustment of the antenna.
Your CB is now ready for use.
3
 HOW TO USE YOUR CB RADIO D 80 FM (26.565 - 27.405 MHz), 4 W
1. ON/OFF-Volume 40 AM (26.965 - 27.405 MHz), 1W.
a)To turn the set on, turn the knob (1) clockwise. EU 40 FM (26.965 - 27.405 MHz), 4 W
b)To increase the sound level, turn the same knob further clockwise. 40 AM (26.965 - 27.405 MHz), 1W.
EC 40 FM (26.965 - 27.405 MHz), 4 W.
2. Manual Squelch
UK 40 FM (27.60125 - 27.99125 MHz), 4 W
Turn the SQ knob(2) clockwise to the exact point where all background
noise disappears. 3OHDVHQRWHWKDWWKLVFRQWUROLV¿QHUHJXODWLRQLI\RX 40 FM (26.965 - 27.405 MHz), 4W.
set this SQ control to the maximum (fully clockwise), the radio can PL 40 FM (26.960 - 27.400 MHz), 4 W
only receive the strongest signal. 40 AM (26.960 - 27.400 MHz), 4W.
3. Automatic Squelch E 40 FM (26.965 - 27.405 MHz), 4 W
The automatic squelch (ASQ ) uses a preset average value. It can be 40 AM (26.965 - 27.405 MHz), 4W.
activated by short key (5) [ ASQ ],The automatic squelch mode (AQ US 40 AM (26.965 - 27.405 MHz), 4W.
icon) is indicated on the LCD. NZ 40 FM (26.330 - 26.770 MHz), 4 W
4. Channel selection 40 AM (26.330 - 26.770 MHz), 4W.
All channels can be selected by channel selector keys (8) [ ] or (9) To change current norm, please hold the key (6) [AM/FM ] while
4 [ ].The selected channel is displayed on the LCD. In turning the radio on. In the display, the symbol of the current norm
communication both transceivers (the receiving and transmitting party) appears, please select the norm by pressing the channel selector
need to be in the same channel and under same modulation type. key(8) [ ] or (9) [ ]. To verify your selection, turn the
radio off and on again, the radio automatically returns to the selected
5. Modulation MODE selection operation mode.
This key (6) [AM/FM] allows selecting the AM or FM modulation. Your Note:
modulation mode has to correspond to the one of your correspondent. The norm is internally set to 40 channels FM, 4 Watts only.
With the version Full Multi Norm in the norm UK, you can switch 7. Automatic Scanning
between the EU.band and the UK band, which is indicated by symbol Press the key(10) [ SC ] to enable the SCAN function. Before enabling
"EU" or "UK", by pressing the key (6) [AM/FM ]. the SCAN function, firstly turn the SQ control clockwise till the
The CB band EU consists of the 40 CEPT channels. The CB band UK background noise is cut out. Then press the key(10) [ SC ], radio will
consists of 40 channels starting from 27.60125 MHz to 27.99125 MHz. automatically scan all channels and the SC icon will appear on the
6. Norm Selection LCD.
When a signal is detected on a channel, scanning stops on this
The version Full Multi Norm can be set by the user to the following
channel. You can receive the calling, and also, can transmit on this
norms:
channel by pressing PTT key. If there is no transmission or detected
signal on that channel within 5 seconds, radio will start scanning
again. To exit the SCAN function, press the SC Key or the PTT key.
8. Priority Channel 9 / 19
-It the contains the priority channels 9 and 19. Priority channel 9
is selected by pressing the key (7) [ CH9/19 ] once. To set priority
channel 19, press the key(7) [ CH9/19 ] twice.
9. Transmitting
To transmit, press and hold the key(A) [ PTT ] at the microphone and
the TX icon will appear on the LCD.
For best quality, please speak normally at a distance of 2 - 4 inches.
6SHDNLQJWRRORXGO\ZLOOFDXVHGLVWRUWLRQVDQGPDNHWKHVLJQDOGLI¿FXOW
to understand.
On completion of the transmission release the PTT key and the radio
will revert to receiving mode.
10. External speaker jack
The radio is equipped with a 3.5 mm jack socket(D) at the rear panel
to connect an external.speaker of 4 - 8 ohm impedance. At 4 ohms the 5
speaker load can be 4 watts. When the external speaker is connected,
the internal speaker will be switched off.
 TECHNICAL CHARACTERISTICS
GENERAL
Modulation modes AM/FM
Frequency ranges 26.965---27.405MHz
Antenna impedance 50 Ohms
Power supply 13.2V
Dimensions(in mm) 150×140×41mm
Weight 761G
TRANSMISSION
Frepuency error +/- 300HZ
Carrier power 1W/4W
Transmission interference inferior to 4nW(-54dBm)
Audio response 300HZ to 3KHZ in AM/FM
Emitted power in the adj.channel inferior to 20uW
6 Microphone sensitivity 3mV
Maximum current max 3A
Modulated singal distortion inferior to 5%
RECEPTION
0.8uV -113 dBm FM
Max sensitivity at 20dB sinad
1.5uV -103 dBm AM
Frequency response 300HZ to 3KHZ in AM/FM
Adjacent channel selectivity 60dB
Maximum audio power 3W
Minimum 0.2uv -120 dBm
Squelch sensitivity
Maximum 1mV -47 dBm
Maximum current 0.3A nominal/1.2A maximum
A1.0-11/08