Cambi e Nap Yokogawa

User’s
Manual Model EJA210A and EJA220A

Flange Mounted Differential
Pressure Transmitters
IM 01C21C01-01E
IM 01C21C01-01E
12th Edition
i
Model EJA210A and EJA220A

Flange Mounted Differential Pressure Transmitters
IM 01C21C01-01E 12th Edition
Contents
1. Introduction................................................................................................ 1-1
 Regarding This Manual................................................................................................. 1-1
1.1 For Safe Use of Product ................................................................................... 1-2
1.2 Warranty.............................................................................................................. 1-3
1.3 ATEX Documentation........................................................................................ 1-4
2. Handling Cautions..................................................................................... 2-1
2.1 Model and Specifications Check...................................................................... 2-1
2.2 Unpacking........................................................................................................... 2-1
2.3 Storage................................................................................................................ 2-1
2.4 Selecting the Installation Location ................................................................. 2-1
2.5 Pressure Connection......................................................................................... 2-2
2.6 Waterproofing of Cable Conduit Connections............................................... 2-2
2.7 Restrictions on Use of Radio Transceiver...................................................... 2-2
2.8 Insulation Resistance and Dielectric Strength Test....................................... 2-2
2.9 Installation of Explosion Protected Type........................................................ 2-3
2.9.1 FM Approval........................................................................................ 2-4
2.9.2 CSA Certification................................................................................. 2-5
2.9.3 IECEx Certification.............................................................................. 2-7
2.9.4 ATEX Certification............................................................................... 2-8
2.10 EMC Conformity Standards............................................................................ 2-11
2.11 PED (Pressure Equipment Directive)............................................................ 2-11
2.12 Low Voltage Directive...................................................................................... 2-12
3. Component Names................................................................................... 3-1
4. Installation.................................................................................................. 4-1
4.1 Precautions ....................................................................................................... 4-1
4.2 Mounting ............................................................................................................ 4-1
4.3 Rotating Transmitter Section............................................................................ 4-1
4.4 Changing the Direction of Integral Indicator ................................................. 4-2
4.5 Affixing the Teflon Film..................................................................................... 4-2
5. Installing Impulse Piping.......................................................................... 5-1
5.1 Impulse Piping Installation Precautions......................................................... 5-1
5.1.1 Connecting Impulse Piping to the Transmitter.................................... 5-1
5.1.2 Routing the Impulse Piping................................................................. 5-1
12th Edition: July 2015 (KP) IM 01C21C01-01E

All Rights Reserved, Copyright © 1997, Yokogawa Electric Corporation
ii
5.2 Impulse Piping Connection Examples............................................................ 5-2
6. Wiring.......................................................................................................... 6-1
6.1 Wiring Precautions............................................................................................ 6-1
6.2 Selecting the Wiring Materials.......................................................................... 6-1
6.3 Connections of External Wiring to Terminal Box........................................... 6-1
6.3.1 Power Supply Wiring Connection....................................................... 6-1
6.3.2 External Indicator Connection............................................................ 6-1
6.3.3 BRAIN TERMINAL BT200 Connection.............................................. 6-1
6.3.4 Check Meter Connection.................................................................... 6-2
6.4 Wiring.................................................................................................................. 6-2
6.4.1 Loop Configuration............................................................................. 6-2
6.4.2 Wiring Installation................................................................................ 6-2
6.5 Grounding........................................................................................................... 6-3
6.6 Power Supply Voltage and Load Resistance.................................................. 6-3
7. Operation.................................................................................................... 7-1
7.1 Preparation for Starting Operation.................................................................. 7-1
7.2 Zero Point Adjustment...................................................................................... 7-2
7.2.1 When you can obtain Low Range Value from actual measured
value of 0% (0 kPa, atmospheric pressure);....................................... 7-2
7.2.2 When you cannot obtain Low Range Value from actual measured
value of 0%;........................................................................................ 7-3
7.3 Starting Operation............................................................................................. 7-3
7.4 Shutting Down Operation................................................................................. 7-4
7.5 Venting or Draining Transmitter Pressure-detector Section........................ 7-4
7.5.1 Draining Condensate.......................................................................... 7-4
7.5.2 Venting Gas........................................................................................ 7-4
7.6 Setting the Range Using the Range-setting Switch....................................... 7-4
8. BRAIN TERMINAL BT200 Operation....................................................... 8-1
8.1 BT200 Operation Precautions.......................................................................... 8-1
8.1.1 Connecting the BT200........................................................................ 8-1
8.1.2 Conditions of Communication Line..................................................... 8-1
8.2 BT200 Operating Procedures........................................................................... 8-2
8.2.1 Key Layout and Screen Display.......................................................... 8-2
8.2.2 Operating Key Functions.................................................................... 8-2
8.2.3 Calling Up Menu Addresses Using the Operating Keys..................... 8-4
8.3 Setting Parameters Using the BT200............................................................... 8-5
8.3.1 Parameter Summary.......................................................................... 8-5
8.3.2 Parameter Usage and Selection......................................................... 8-8
8.3.3 Setting Parameters............................................................................. 8-9
(1) Tag No. Setup .................................................................................... 8-9
(2) Calibration Range Setup..................................................................... 8-9
(3) Damping Time Constant Setup . ...................................................... 8-10
IM 01C21C01-01E
iii
(4) Output Signal Low Cut Mode Setup ................................................ 8-11
(5) Change Output Limits ...................................................................... 8-11
(6) Integral Indicator Scale Setup........................................................... 8-11
(7) Unit Setup for Displayed Temperature . ........................................... 8-13
(8) Unit Setup for Displayed Static Pressure ........................................ 8-13
(9) Operation Mode Setup . ................................................................... 8-13
(10) Output Status Display/Setup when a CPU Failure .......................... 8-14
(11) Output Status Setup when a Hardware Error Occurs ..................... 8-14
(12) Range Change while Applying Actual Inputs ................................... 8-14
(13) Zero Point Adjustment ..................................................................... 8-15
(14) Span Adjustment............................................................................... 8-16
(15) Test Output Setup ............................................................................ 8-17
(16) User Memo Fields............................................................................. 8-17
8.4 Displaying Data Using the BT200................................................................... 8-18
8.4.1 Displaying Measured Data............................................................... 8-18
8.4.2 Display Transmitter Model and Specifications.................................. 8-18
8.5 Self-Diagnostics............................................................................................... 8-18
8.5.1 Checking for Problems..................................................................... 8-18
8.5.2 Errors and Countermeasures........................................................... 8-20
9. Maintenance............................................................................................... 9-1
9.1 Overview............................................................................................................. 9-1
9.2 Calibration Instruments Selection................................................................... 9-1
9.3 Calibration.......................................................................................................... 9-1
9.4 Disassembly and Reassembly......................................................................... 9-3
9.4.1 Replacing the Integral Indicator.......................................................... 9-3
9.4.2 Replacing the CPU Board Assembly.................................................. 9-4
9.4.3 Replacing the Process Connector Gaskets........................................ 9-5
9.5 Troubleshooting................................................................................................. 9-5
9.5.1 Basic Troubleshooting........................................................................ 9-5
9.5.2 Troubleshooting Flow Charts.............................................................. 9-6
10. General Specifications........................................................................... 10-1
10.1 Standard Specifications.................................................................................. 10-1
10.2 Model and Suffix Codes.................................................................................. 10-3
10.3 Optional Specifications................................................................................... 10-5
10.4 Dimensions....................................................................................................... 10-8
Customer Maintenance Parts List
DPharp EJA Series Transmitter Section.........................................CMPL 01C21A01-02E
Model EJA210A and EJA220A
Flange Mounted Differential Pressure Transmitter........................CMPL 01C21C01-01E
Revision Information
IM 01C21C01-01E
<1. Introduction> 1-1
1. Introduction
Thank you for purchasing the DPharp electronic
pressure transmitter. NOTE
The DPharp Pressure Transmitters are precisely For FOUNDATION FieldbusTM, PROFIBUS PA
calibrated at the factory before shipment. To ensure and HART protocol versions, please refer to
correct and efficient use of the instrument, please IM 01C22T02-01E, IM 01C22T03-00E and IM
read this manual thoroughly and fully understand 01C22T01-01E respectively, in addition to this
how to operate the instrument before operating it. manual.
• The following safety symbol marks are used in

 Regarding This Manual this manual:
• This manual should be passed on to the end
user.
• The contents of this manual are subject to WARNING
change without prior notice.
Indicates a potentially hazardous situation which,
• All rights reserved. No part of this manual may if not avoided, could result in death or serious
be reproduced in any form without Yokogawa’s injury.
written permission.
• Yokogawa makes no warranty of any kind with
regard to this manual, including, but not limited
to, implied warranty of merchantability and
CAUTION
fitness for a particular purpose. Indicates a potentially hazardous situation which,
• If any question arises or errors are found, or if if not avoided, may result in minor or moderate
any information is missing from this manual, injury. It may also be used to alert against unsafe
please inform the nearest Yokogawa sales practices.
office.
• The specifications covered by this manual are
IMPORTANT
limited to those for the standard type under the
specified model number break-down and do not Indicates that operating the hardware or software
cover custom-made instruments. in this manner may damage it or lead to system
• Please note that changes in the specifications, failure.
construction, or component parts of the
instrument may not immediately be reflected
in this manual at the time of change, provided NOTE
that postponement of revisions will not cause
Draws attention to information essential for
difficulty to the user from a functional or
understanding the operation and features.
performance standpoint.
• Yokogawa assumes no responsibilities for this
Direct current
product except as stated in the warranty.
• If the customer or any third party is harmed by
the use of this product, Yokogawa assumes
no responsibility for any such harm owing to
any defects in the product which were not
predictable, or for any indirect damages.
IM 01C21C01-01E
1.1 For Safe Use of Product (c) Operation
For the protection and safety of the operator • Wait 10 min. after power is turned off, before
and the instrument or the system including the opening the covers.
instrument, please be sure to follow the instructions
(d) Maintenance
on safety described in this manual when handling
this instrument. In case the instrument is handled in • Please do not carry out except being written
contradiction to these instructions, Yokogawa does to a maintenance descriptions. When these
not guarantee safety. Please give your attention to procedures are needed, please contact nearest
the followings. YOKOGAWA office.
• Care should be taken to prevent the build up of
(a) Installation
drift, dust or other material on the display glass
• The instrument must be installed by an expert and name plate. In case of its maintenance, soft
engineer or a skilled personnel. The procedures and dry cloth is used.
described about INSTALLATION are not
permitted for operators. (e) Explosion Protected Type Instrument
• In case of high process temperature, care • Users of explosion proof instruments should
should be taken not to burn yourself because refer first to section 2.9 (Installation of an
the surface of body and case reaches a high Explosion Protected Instrument) of this manual.
temperature. • The use of this instrument is restricted to those
• The instrument installed in the process is under who have received appropriate training in the
pressure. Never loosen the process connector device.
bolts to avoid the dangerous spouting of • Take care not to create sparks when accessing
process fluid. the instrument or peripheral devices in a
• During draining condensate from the hazardous location.
pressuredetector section, take appropriate care
to avoid contact with the skin, eyes or body, or (f) Modification
inhalation of vapors, if the accumulated process • Yokogawa will not be liable for malfunctions or
fluid may be toxic or otherwise harmful. damage resulting from any modification made
• When removing the instrument from hazardous to this instrument by the customer.
processes, avoid contact with the fluid and the
interior of the meter.
• All installation shall comply with local installation
requirement and local electrical code.
(b) Wiring
• The instrument must be installed by an expert
engineer or a skilled personnel. The procedures
described about WIRING are not permitted for
operators.
• Please confirm that voltages between the
power supply and the instrument before
connecting the power cables and that the
cables are not powered before connecting.
IM 01C21C01-01E
1.2 Warranty
• The warranty shall cover the period noted on
the quotation presented to the purchaser at the
time of purchase. Problems occurred during the
warranty period shall basically be repaired free
of charge.
• In case of problems, the customer should
contact the Yokogawa representative from
which the instrument was purchased, or the
nearest Yokogawa office.
• If a problem arises with this instrument,
please inform us of the nature of the problem
and the circumstances under which it
developed, including the model specification
and serial number. Any diagrams, data and
other information you can include in your
communication will also be helpful.
• Responsible party for repair cost for the
problems shall be determined by Yokogawa
based on our investigation.
• The Purchaser shall bear the responsibility for
repair costs, even during the warranty period, if
the malfunction is due to:
- Improper and/or inadequate maintenance by
the purchaser.
- Failure or damage due to improper handling,
use or storage which is out of design
conditions.
- Use of the product in question in a location
not conforming to the standards specified by
Yokogawa, or due to improper maintenance
of the installation location.
- Failure or damage due to modification or
repair by any party except Yokogawa or an
approved representative of Yokogawa.
- Malfunction or damage from improper
relocation of the product in question after
delivery.
- Reason of force majeure such as fires,
earthquakes, storms/floods, thunder/
lightening, or other natural disasters, or
disturbances, riots, warfare, or radioactive
contamination.
IM 01C21C01-01E
1.3 ATEX Documentation
This procedure is only applicable to the countries in European Union.
GB SK
CZ
DK
I LT
E LV
EST
NL
PL
SF
SLO
P
BG
RO
S
M
GR
IM 01C21C01-01E
<2. Handling Cautions> 2-1
2. Handling Cautions
This chapter describes important cautions 2.2 Unpacking
regarding how to handle the transmitter. Read
carefully before using the transmitter. When moving the transmitter to the installation site,
keep it in its original packaging. Then, unpack the
The EJA-A Series pressure transmitters are transmitter there to avoid damage on the way.
thoroughly tested at the factory before shipment.
When the transmitter is delivered, visually check
them to make sure that no damage occurred during 2.3 Storage
shipment. The following precautions must be observed when
Also check that all transmitter mounting hardware storing the instrument, especially for a long period.
shown in Figure 2.1 is included. If the transmitter (a) Select a storage area which meets the following
was ordered without the mounting bracket or conditions:
without the process connector, the transmitter • It is not exposed to rain or water.
mounting hardware is not included. After checking • It suffers minimum vibration and shock.
the transmitter, repack it in the way it was delivered • It has an ambient temperature and relative
until installation. humidity within the following ranges.
Ambient temperature:
-40 to 85°C without integral indicator
-30 to 80°C with integral indicator
Relative humidity:
5% to 100% R.H. (at 40°C)
Process connector
Preferred temperature and humidity:
approx. 25°C and 65% R.H.
(b) When storing the transmitter, repack it as nearly
as possible to the way it was packed when
Bolt Process connector gasket delivered from the factory.
F0201.ai
(c) If storing a transmitter that has been used,
Figure 2.1 Transmitter Mounting Hardware
thoroughly clean the chambers inside the cover
flanges, so that no measured fluid remains
in it. Also make sure before storing that the
2.1 Model and Specifications pressure-detector and transmitter section are
Check securely mounted.
The model name and specifications are indicated

on the name plate attached to the case. If the 2.4 Selecting the Installation
reverse operating mode was ordered (reverse Location
signal), ‘REVERSE’ will be inscribed in field *1.
The transmitter is designed to withstand severe
environmental conditions. However, to ensure
stable and accurate operation for years, observe
the following precautions when selecting an
installation location.
: Refer to USER'S MANUAL
F0202.ai (a) Ambient Temperature

Figure 2.2 Name Plate Avoid locations subject to wide temperature
variations or a significant temperature gradient.
If the location is exposed to radiant heat from
plant equipments, provide adequate thermal
insulation and/or ventilation.
IM 01C21C01-01E
(b) Ambient Atmosphere 2.6 Waterproofing of Cable
Avoid installing the transmitter in a corrosive
atmosphere. If the transmitter must be installed
Conduit Connections
in a corrosive atmosphere, there must be Apply a non-hardening sealant to the threads
adequate ventilation as well as measures to to waterproof the transmitter cable conduit
prevent intrusion or stagnation of rain water in connections. (See Figure 6.7, 6.8 and 6.9.)
conduits.
(c) Shock and Vibration
Select an installation site suffering minimum 2.7 Restrictions on Use of Radio
shock and vibration (although the transmitter is Transceiver
designed to be relatively resistant to shock and
vibration). IMPORTANT
(d) Installation of Explosion-protected Transmitters
Explosion-protected transmitters can be Although the transmitter has been designed to
installed in hazardous areas according to the resist high frequency electrical noise, if a radio
types of gases for which they are certified. transceiver is used near the transmitter or its
See Subsection 2.9 “Installation of Explosion external wiring, the transmitter may be affected
Protected Type Transmitters.” by high frequency noise pickup. To test for such
effects, bring the transceiver in use slowly from a
distance of several meters from the transmitter,
2.5 Pressure Connection and observe the measurement loop for noise
effects. Thereafter, always use the transceiver
WARNING outside the area affected by noise.
• Instrument installed in the process is

under pressure. Never loosen the process
connector bolts to avoid the dangerous 2.8 Insulation Resistance and
spouting of process fluid. Dielectric Strength Test
• During draining condensate from the
Since the transmitter has undergone insulation
pressure-detector section, take appropriate
resistance and dielectric strength tests at the
care to avoid contact with the skin, eyes
factory before shipment, normally these tests are
or body, or inhalation of vapors, if the
not required. However, if required, observe the
accumulated process fluid may be toxic or
following precautions in the test procedures.
otherwise harmful.
(a) Do not perform such tests more frequently than
The following precautions must be observed is absolutely necessary. Even test voltages that
in order to safely operate the transmitter under do not cause visible damage to the insulation
pressure. may degrade the insulation and reduce safety
margins.
(a) Make sure that the two process connector bolts (b) Never apply a voltage exceeding 500 V DC
are tightened firmly. (100 V DC with an internal lightning protector)
(b) Make sure that there are no leaks in the impulse for the insulation resistance test, nor a voltage
piping. exceeding 500 V AC (100 V AC with an internal
(c) Never apply a pressure higher than the lightning protector) for the dielectric strength
specified maximum working pressure. test.
(c) Before conducting these tests, disconnect
all signal lines from the transmitter terminals.
Perform the tests in the following procedure:
IM 01C21C01-01E
• Insulation Resistance Test 2.9 Installation of Explosion
1) Short-circuit the + and – SUPPLY terminals in Protected Type
the terminal box.
In this section, further requirements and differences
2) Turn OFF the insulation tester. Then connect
and for explosionproof type instrument are
the insulation tester plus (+) lead wire to the
described. For explosionproof type instrument,
shorted SUPPLY terminals and the minus (–)
the description in this chapter is prior to other
leadwire to the grounding terminal.
description in this users manual.
3) Turn ON the insulation tester power and
measure the insulation resistance. The voltage For the intrinsically safe equipment and
should be applied short as possible to verify explosionproof equipment, in case the instrument
that the insulation resistance is at least 20 MΩ. is not restored to its original condition after any
4) After completing the test and being very careful repair or modification undertaken by the customer,
not to touch exposed conductors disconnect the intrinsically safe construction or explosionproof
insulation tester and connect a 100 kΩ resistor construction is damaged and may cause dangerous
between the grounding terminal and the short- condition. Please contact Yokogawa for any repair
circuiting SUPPLY terminals. Leave this resistor or modification required to the instrument.
connected at least one second to discharge any
static potential. Do not touch the terminals while NOTE
it is discharging.
For FOUNDATION Fieldbus and PROFIBUS
• Dielectric Strength Test PA explosion protected type, please refer to
1) Short-circuit the + and – SUPPLY terminals in IM 01C22T02-01E and IM 01C22T03-00E
the terminal box. respectively.
2) Turn OFF the dielectric strength tester. Then
connect the tester between the shorted
SUPPLY terminals and the grounding terminal. CAUTION
Be sure to connect the grounding lead of the
dielectric strength tester to the ground terminal. This instrument is tested and certified as
3) Set the current limit on the dielectric strength intrinsically safe type or explosionproof
tester to 10 mA, then turn ON the power and type. Please note that the construction of
gradually increase the test voltage from ‘0’ to the instrument, installation, external wiring,
the specified voltage. maintenance or repair is strictly restricted, and
4) When the specified voltage is reached, hold it non-observance or negligence of this restriction
for one minute. would result in dangerous condition.
5) After completing this test, slowly decrease the
voltage to avoid any voltage surges.
WARNING
To preserve the safety of explosionproof
equipment requires great care during mounting,
wiring, and piping. Safety requirements also
place restrictions on maintenance and repair
activities. Please read the following sections very
carefully.
IM 01C21C01-01E
2.9.1 FM Approval Note 3. Installation
• Barrier must be installed in an enclosure that
a. FM Intrinsically Safe Type meets the requirements of ANSI/ISA S82.01.
Caution for FM intrinsically safe type. (Following • Control equipment connected to barrier must
contents refer “DOC. No. IFM012-A12 P.1 and not use or generate more than 250 V rms or
2.”) V dc.
• Installation should be in accordance with
Note 1. Model EJA Series pressure transmitters ANSI/ISA RP12.6 “Installation of Intrinsically
with optional code /FS1 are applicable for Safe Systems for Hazardous (Classified)
use in hazardous locations. Locations” and the National Electric Code
• Applicable Standard: FM3600, FM3610, (ANSI/NFPA 70).
FM3611, FM3810, ANSI/NEMA250 • The configuration of associated apparatus
• Intrinsically Safe for Class I, Division 1, must be FMRC Approved.
Groups A, B, C & D. Class II, Division 1, • Dust-tight conduit seal must be used when
Groups E, F & G and Class III, Division 1 installed in a Class II, III, Group E, F and G
Hazardous Locations. environments.
• Nonincendive for Class I, Division 2, Groups • Associated apparatus manufacturer’s
A, B, C & D. Class II, Division 2, Groups E, installation drawing must be followed when
F & G and Class III, Division 1 Hazardous installing this apparatus.
Locations. • The maximum power delivered from the
• Outdoor hazardous locations, NEMA 4X. barrier must not exceed 0.9 W.
• Temperature Class: T4 • Note a warning label worded
• Ambient temperature: –40 to 60°C “SUBSTITUTION OF COMPONENTS MAY
Note 2. Entity Parameters IMPAIR INTRINSIC SAFETY,” and “INSTALL
• Intrinsically Safe Apparatus Parameters IN ACCORDANCE WITH DOC. No. IFM012-
[Groups A, B, C, D, E, F and G] A12 P.1 and 2.”
Vmax = 30 V Ci = 22.5 nF Note 4. Maintenance and Repair
Imax = 165 mA Li = 730 µH • The instrument modification or parts
Pmax = 0.9 W replacement by other than authorized
* Associated Apparatus Parameters representative of Yokogawa Electric
(FM approved barriers) Corporation is prohibited and will void
Factory Mutual Intrinsically safe and
Voc ≤ 30 V Ca > 22.5 nF
Nonincendive Approval.
Isc ≤ 165 mA La > 730 µH
Pmax ≤ 0.9W [Intrinsically Safe]
Hazardous Location Nonhazardous Location
• Intrinsically Safe Apparatus Parameters
[Groups C, D, E, F and G] Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G General
Vmax = 30 V Ci = 22.5 nF
EJA Series Pressure Purpose
Imax = 225 mA Li = 730 µH Transmitters Safety Barrier Equipment
Pmax = 0.9 W + + + +
Supply – – – –
* Associated Apparatus Parameters
(FM approved barriers)
Voc ≤ 30 V Ca > 22.5 nF
Isc ≤ 225 mA La > 730 µH [Nonincendive]
Pmax ≤ 0.9 W Hazardous Location Nonhazardous Location
Class I, II, Division 2,
• Entity Installation Requirements Groups A, B, C, D, E, F, G
Vmax ≥ Voc or Vt, Imax ≥ Isc or It, Class III, Division 1. General
Pmax (IS Apparatus) ≥ Pmax (Barrier) EJA Series Pressure Purpose
Ca ≥ Ci + Ccable, La ≥ Li + Lcable Transmitters Equipment
+ +
Supply – –
Not Use
Safety Barrier
F0203.ai
IM 01C21C01-01E
b. FM Explosionproof Type Note 1. For the installation of this transmitter,
once a particular type of protection is
Caution for FM explosionproof type.
selected, any other type of protection
Note 1. Model EJA Series differential, gauge, cannot be used. The installation must be in
and absolute pressure transmitters with accordance with the description about the
optional code /FF1 are applicable for use in type of protection in this instruction manual.
hazardous locations.
Note 2. In order to avoid confusion, unnecessary
• Applicable Standard: FM3600, FM3615,
marking is crossed out on the label other
FM3810, ANSI/NEMA250
than the selected type of protection when
• Explosionproof for Class I, Division 1,
the transmitter is installed.
Groups B, C and D.
• Dust-ignitionproof for Class II/III, Division 1, 2.9.2 CSA Certification
Groups E, F and G.
• Outdoor hazardous locations, NEMA 4X. a. CSA Intrinsically Safe Type
• Temperature Class: T6 Caution for CSA Intrinsically safe type.
• Ambient Temperature: –40 to 60°C (Following contents refer to “DOC No. ICS003-
• Supply Voltage: 42 V dc max. A12 P.1-1 and P.1-2.”)
• Output signal: 4 to 20 mA
Note 1. Model EJA Series differential, gauge,
Note 2. Wiring and absolute pressure transmitters with
• All wiring shall comply with National Electrical optional code /CS1 are applicable for use
Code ANSI/NEPA70 and Local Electrical in hazardous locations
Codes. Certificate: 1053843
• When installed in Division 1, “FACTORY • Applicable Standard: C22.2 No.0, No.0.4,
SEALED, CONDUIT SEAL NOT No.25, No.30, No.94, No.142, No.157,
REQUIRED.” No.213
Note 3. Operation • Intrinsically Safe for Class I, Division 1,
• Keep the “CAUTION” nameplate attached to Groups A, B, C & D. Class II, Division 1,
the transmitter. Groups E, F & G and Class III, Division 1
CAUTION: OPEN CIRCUIT BEFORE Hazardous Locations.
REMOVING COVER. FACTORY SEALED, • Nonincendive for Class I, Division 2, Groups
CONDUIT SEAL NOT REQUIRED. A, B, C & D, Class II, Division 2, Groups F &
INSTALL IN ACCORDANCE WITH THE G, and Class III, Hazardous Locations. (not
INSTRUCTION MANUAL IM 1C22. use Safety Barrier)
• Take care not to generate mechanical • Encl. “Type 4X”
sparking when accessing to the instrument • Temperature Class: T4
and peripheral devices in a hazardous • Ambient temperature: –40* to 60°C
location. * –15°C when /HE is specified.
• Process Temperature: 120°C max.
Note 4. Maintenance and Repair
• The instrument modification or parts Note 2. Entity Parameters
replacement by other than authorized • Intrinsically safe ratings are as follows:
representative of Yokogawa Electric Maximum Input Voltage (Vmax) = 30 V
Corporation is prohibited and will void Maximum Input Current (Imax) = 165 mA
Factory Mutual Explosionproof Approval. Maximum Input Power (Pmax) = 0.9 W
Maximum Internal Capacitance (Ci) = 22.5nF
c. FM Intrinsically Safe Type/FM
Maximum Internal Inductance (Li) = 730 µH
Explosionproof Type
* Associated apparatus (CSA certified barriers)
Model EJA Series pressure transmitters with Maximum output voltage (Voc) ≤ 30 V
optional code /FU1 can be selected the type Maximum output current (Isc) ≤ 165 mA
of protection (FM Intrinsically Safe or FM Maximum output power (Pmax) ≤ 0.9 W
Explosionproof) for use in hazardous locations.
IM 01C21C01-01E
Note 3. Installation Note 2. Wiring
• All wiring shall comply with Canadian • All wiring shall comply with Canadian
Electrical Code Part I and Local Electrical Electrical Code Part I and Local Electrical
Codes. Codes.
• The instrument modification or parts • In hazardous location, wiring shall be in
replacement by other than authorized conduit as shown in the figure.
representative of Yokogawa Electric CAUTION: SEAL ALL CONDUITS WITHIN
Corporation and Yokogawa Corporation 50 cm OF THE ENCLOSURE.
of America is prohibited and will void UN SCELLEMENT DOIT ÊTRE INSTALLÉ À
Canadian Standards Intrinsically safe and MOINS DE 50 cm DU BîTIER.
nonincendive Certification. • When installed in Division 2, “SEALS NOT
REQUIRED.”
[Intrinsically Safe]
Hazardous Location Nonhazardous Location Note 3. Operation
Class I, II, III, Division 1, • Keep the “CAUTION” label attached to the
Groups A, B, C, D, E, F, G General transmitter.
EJA Series Pressure Purpose CAUTION: OPEN CIRCUIT BEFORE
Transmitters Safety Barrier Equipment
REMOVING COVER.
+ + + +
OUVRIR LE CIRCUIT AVANT D´NLEVER
LE COUVERCLE.
• Take care not to generate mechanical
sparking when accessing to the instrument
[Nonincendive] and peripheral devices in a hazardous
Hazardous Location Nonhazardous Location location.
Class I, II, Division 2,
Groups A, B, C, D, E, F, G
Class III, Division 1. General • The instrument modification or parts
EJA Series Pressure Purpose replacement by other than authorized
Transmitters Equipment representative of Yokogawa Electric
+ + Corporation and Yokogawa Corporation of
Supply – – America is prohibited and will void Canadian
Not Use
Safety Barrier
Standards Explosionproof Certification.
F0204.ai
Non-Hazardous Hazardous Locations Division 1

Locations
b. CSA Explosionproof Type
Non-hazardous
Caution for CSA explosionproof type. Location
Equipment 50 cm Max.
Note 1. Model EJA Series differential, gauge,
and absolute pressure transmitters with
optional code /CF1 are applicable for use 42 V DC Max. Conduit
in hazardous locations: 4 to 20 mA DC Sealing Fitting
Signal
Certificate: 1089598 EJA Series
• Applicable Standard: C22.2 No.0, No.0.4, Non-Hazardous Hazardous Locations Division 2
No.25, No.30, No.94, No.142 Locations
• Explosionproof for Class I, Division 1, Non-hazardous
Groups B, C and D. Location
Equipment
• Dust-ignitionproof for Class II/III, Division 1,
Groups E, F and G.
• Encl “Type 4X”
42 V DC Max.
• Temperature Class: T6, T5, and T4 4 to 20 mA DC Sealing Fitting
• Process Temperature: Signal
EJA Series
85°C (T6),100°C (T5), and 120°C (T4) F0205.ai
• Ambient Temperature: –40* to 80°C
* –15°C when /HE is specified.
• Supply Voltage: 42 V dc max.
• Output Signal: 4 to 20 mA
IM 01C21C01-01E
c. CSA Intrinsically Safe Type/CSA Note 2. Entity Parameters
Explosionproof Type • Intrinsically safe ratings are as follows:
Maximum Input Voltage (Ui) = 30 V
Model EJA Series pressure transmitters with
Maximum Input Current (Ii) = 165 mA
optional code /CU1 can be selected the type
Maximum Input Power (Pi) = 0.9 W
of protection (CSA Intrinsically Safe or CSA
Maximum Internal Capacitance (Ci) = 22.5nF
Explosionproof) for use in hazardous locations.
Maximum Internal Inductance (Li) = 730 µH
Note 1. For the installation of this transmitter, • Type “n” ratings are as follows:
once a particular type of protection is Maximum Input Voltage (Ui) = 30 V
selected, any other type of protection Maximum Internal Capacitance (Ci) = 22.5nF
cannot be used. The installation must be in Maximum Internal Inductance (Li) = 730 µH
accordance with the description about the • Installation Requirements
type of protection in this instruction manual. Uo ≤ Ui, Io ≤ Ii, Po ≤ Pi,
Note 2. In order to avoid confusion, unnecessary Co ≥ Ci + Ccable, Lo ≥ Li + Lcable
marking is crossed out on the label other Uo, Io, Po, Co, and Lo are parameters of
than the selected type of protection when barrier.
the transmitter is installed. Note 3. Installation
2.9.3 IECEx Certification • In any safety barreir used output current
must be limited by a resistor 'R' such that
Model EJA Series differential, gauge, and absolute Io=Uo/R.
pressure transmitters with optional code /SU2 • The safety barrier must be IECEx certified.
can be selected the type of protection (IECEx • Input voltage of the safety barrier must be
Intrinsically Safe/type n or flameproof) for use in less than 250 Vrms/Vdc.
hazardous locations. • The instrument modification or parts
replacement by other than authorized
Note 1. For the installation of this transmitter, representative of Yokogawa Electric
once a particular type of protection is Corporation and will void IECEx Intrinsically
selected, any other type of protection safe and type n certification.
cannot be used. The installation must be in • The cable entry devices and blanking
accordance with the description about the elements for type n shall be of a certified type
type of protection in this instruction manual. providing a level of ingress protection of at
Note 2. In order to avoid confusion, unnecessary least IP54, suitable for the conditions of use
marking is crossed out on the label other and correctly installed.
than the selected type of protection when • Electrical Connection:
the transmitter is installed. The type of electrical connection is stamped
near the electrical connection port according
a. IECEx Intrinsically Safe Type / type n
to the following marking.
Caution for IECEx Intrinsically safe and type n.
Screw Size Marking
Note 1. Model EJA Series differential, gauge, M
ISO M20 × 1.5 female
ANSI 1/2 NPT female A
optional code /SU2 are applicable for use
in hazardous locations.
• No. IECEx KEM 06.0007X
• Applicable Standard: IEC 60079-0:2004,
IEC 60079-11:1999, IEC 60079-15:2005,
IEC 60079-26:2004 Location of the marking
• Type of Protection and Marking Code:

F0206.ai
Ex ia IIC T4, Ex nL IIC T4
• Ambient Temperature :–40 to 60°C
• Max. Process Temp.: 120°C
• Enclosure: IP67
IM 01C21C01-01E
Note 4. Operation • Ambient Temperature: –40 to 75°C (T4),
• WARNING: –40 to 80°C (T5), –40 to 75°C (T6)
WHEN AMBIENT TEMPERATURE ≥ 55°C, • Supply Voltage: 42 V dc max.
USE THE HEAT-RESISTING CABLES ≥ • Output Signal: 4 to 20 mA dc
90°C.
Note 2. Wiring
Note 5. Special Conditions for Safe Use • In hazardous locations, the cable entry
• WARNING: devices shall be of a certified flameproof
IN THE CASE WHERE THE ENCLOSURE type, suitable for the conditions of use and
OF THE PRESSURE TRANSMITTER IS correctly installed.
MADE OF ALUMINUM, IF IT IS MOUNTED • Unused apertures shall be closed with
IN AN AREA WHERE THE USE OF ZONE suitable flameproof certified blanking
0 IS REQUIRED, IT MUST BE INSTALLED elements. (The plug attached is certificated
SUCH, THAT, EVEN IN THE EVENT OF as the flame proof IP67 as a part of this
RARE INCIDENTS, IGNITION SOURCES apparatus.)
DUE TO IMPACT AND FRICTION SPARKS • In case of ANSI 1/2 NPT plug, ANSI
ARE EXCLUDED. hexagonal wrench should be applied to
screw in.
[Intrinsically Safe]
Hazardous Location Nonhazardous Location Note 3. Operation
Group I/IIC, Zone 0 • WARNING:
General AFTER DE-ENERGIZING, DELAY 10
EJA Series Pressure IECEx certified Purpose MINUTES BEFORE OPENING.
Transmitters Safety Barrier Equipment
• WARNING:
+ + + +
WHEN AMBIENT TEMPERATURE ≥ 70°C,
USE THE HEAT-RESISTING CABLES ≥
90°C.
[type n] sparking when accessing to the instrument
Hazardous Location Nonhazardous Location and peripheral devices in a hazardous
Group IIC, Zone 2 location.
EJA Series Pressure IECEx Certified

Transmitters Equipment [nL] • The instrument modification or parts
+ + replacement by other than authorized
Supply – – representative of Yokogawa Electric
Not Use Corporation is prohibited and will void IECEx
Safety Barrier
F0207.ai
Certification.
2.9.4 ATEX Certification
b. IECEx Flameproof Type
Caution for IECEx flameproof type. (1) Technical Data
Note 1. Model EJA Series differential, gauge, a. ATEX Intrinsically Safe Type
optional code /SU2 are applicable for use Caution for ATEX Intrinsically safe type.
in hazardous locations: Note 1. Model EJA Series differential, gauge,
• No. IECEx KEM 06.0005 and absolute pressure transmitters with
• Applicable Standard: IEC60079-0:2004, optional code /KS2 for potentially explosive
IEC60079-1:2003 atmospheres:
• Type of Protection and Marking Code: • No. KEMA 02ATEX1030 X
Ex d IIC T6...T4 • Applicable Standard: EN 50014:1997,
• Enclosure: IP67 EN 50020:1994, EN 50284:1999
• Maximum Process Temperature:
120°C (T4), 100°C (T5), 85°C (T6)
IM 01C21C01-01E
• Type of Protection and Marking code: b. ATEX Flameproof Type
EEx ia IIC T4
Caution for ATEX flameproof type.
• Temperature Class: T4
• Enclosure: IP67 Note 1. Model EJA Series differential, gauge,
• Process Temperature: 120°C max. and absolute pressure transmitters
• Ambient Temperature: –40 to 60°C with optional code /KF21 for potentially
explosive atmospheres:
Note 2. Electrical Data
• No. KEMA 02ATEX2148
• In type of explosion protection intrinsic
• Applicable Standard: EN 60079-0:2006,
safety EEx ia IIC only for connection to a
EN 60079-1:2004
certified intrinsically safe circuit with following
• Type of Protection and Marking Code:
maximum values:
Ex d IIC T6...T4
Ui = 30 V
• Temperature Class: T6, T5, and T4
Ii = 165 mA
• Enclosure: IP67
Pi = 0.9 W
• Maximum Process Temperature:
Effective internal capacitance; Ci = 22.5 nF
85°C (T6), 100°C (T5), and 120°C (T4)
Effective internal inductance; Li = 730 µH
• Ambient Temperature:
Note 3. Installation T4 and T6; –40* to 75°C, T5; –40* to 80°C
• All wiring shall comply with local installation * –15°C when /HE is specified.
requirements. (Refer to the installation
Note 2. Electrical Data
diagram)
• Supply voltage: 42 V dc max.
Note 4. Maintenance and Repair • Output signal: 4 to 20 mA
• The instrument modification or parts
Note 3. Installation
replacement by other than authorized
• All wiring shall comply with local installation
representative of Yokogawa Electric
requirement.
Corporation is prohibited and will void KEMA
• The cable entry devices shall be of a certified
Intrinsically safe Certification.
flameproof type, suitable for the conditions of
Note 5. Special Conditions for Safe Use use.
• In the case where the enclosure of the
Note 4. Operation
Pressure Transmitter is made of aluminium,
• Keep the “CAUTION” label to the transmitter.
if it is mounted in an area where the use of
CAUTION: AFTER DE-ENERGIZING,
category 1 G apparatus is required, it must
DELAY 10 MINUTES BEFORE OPENING.
be installed such, that, even in the event of
WHEN THE AMBIENT TEMP. ≥ 70°C, USE
rare incidents, ignition sources due to impact
HEAT-RESISTING CABLES ≥ 90°C.
and friction sparks are excluded.
[Installation Diagram] sparking when accessing to the instrument
and peripheral devices in a hazardous
location.
Transmitter Note 5. Maintenance and Repair
+ + • The instrument modification or parts
Supply Safety Barrier *1
– – replacement by other than authorized
representative of Yokogawa Electric
Corporation is prohibited and will void KEMA
Flameproof Certification.
F0208.ai
*1: In any safety barriers used the output current must be

limited by a resistor “R” such that Imaxout-Uz/R.
IM 01C21C01-01E
(2) Electrical Connection (6) Name Plate
The type of electrical connection is stamped  Name plate
near the electrical connection port according to
the following marking.
Screw Size Marking
ISO M20 × 1.5 female M
: Refer to USER'S MANUAL
ANSI 1/2 NPT female A
 Tag plate for flameproof type
Location of the marking

 Tag plate for intrinsically safe type
F0206.ai
(3) Installation
F0211.ai
WARNING MODEL: Specified model code.

STYLE: Style code.
• All wiring shall comply with local installation
SUFFIX: Specified suffix code.
requirement and local electrical code.
SUPPLY: Supply voltage.
• There is no need of the conduit seal for
OUTPUT: Output signal.
both of Division 1 and Division 2 hazardous
MWP: Maximum working pressure.
locations because this product is sealed at
CAL RNG: Specified calibration range.
factory.
DISP MODE: Specified display mode.
• In case of ANSI 1/2 NPT plug, ANSI
OUTPUT MODE: Specified output mode.
hexagonal wrench should be applied to
NO.: Serial number and year of production*1.
screw in.
TOKYO 180-8750 JAPAN:
The manufacturer name and the address*2.
(4) Operation *1: The third figure from the last shows the last one figure
of the year of production. For example, the production
year of the product engraved in “NO.” column on the
WARNING name plate as follows is 2001.
12A819857 132
• OPEN CIRCUIT BEFORE REMOVING
COVER. INSTALL IN ACCORDANCE WITH The year 2001
THIS USER’S MANUAL
*2: “180-8750” is a zip code which represents the
• Take care not to generate mechanical following address.
sparking when access to the instrument and
peripheral devices in hazardous locations. 2-9-32 Nakacho, Musashino-shi, Tokyo Japan
(5) Maintenance and Repair
WARNING
The instrument modification or parts replacement
by other than authorized Representative of
Yokogawa Electric Corporation is prohibited and
will void the certification.
IM 01C21C01-01E
2.10 EMC Conformity Standards
PS*1 PS-V
Model V(L) Category*2
EN 61326-1 Class A, Table 2 (For use in industrial (bar) (bar-L)
locations) Article 3, paragraph 3
EJA110A 160 0.01 1.6
(SEP)
EN 61326-2-3 EJA120A 0.5 0.01 0.005
Article 3, paragraph 3
(SEP)
EN 61326-2-5 (for Fieldbus) Article 3, paragraph 3
EJA130A 420 0.01 4.2
(SEP)
EJA130A
CAUTION With code /PE3
420 0.01 4.2 III
This instrument is a Class A product, and it is EJA310A 160 0.01 1.6
(SEP)
designed for use in the industrial environment. Article 3, paragraph 3
EJA430A 160 0.01 1.6
Please use this instrument in the industrial (SEP)
environment only. Article 3, paragraph 3
EJA440A 500 0.01 50
(SEP)
EJA440A
500 0.01 50 III
With code /PE3
NOTE EJA510A 500 0.01 50
(SEP)
EJA510A With
YOKOGAWA recommends customer to apply 500 0.01 50 III
code /PE3
the Metal Conduit Wiring or to use the twisted Article 3, paragraph 3
EJA530A 500 0.01 50
pair Shield Cable for signal wiring to conform the (SEP)
EJA530A
requirement of EMC Regulation, when customer 500 0.01 50 III
With code /PE3
installs the EJA Series Transmitters to the plant.
*1: PS is maximum allowable pressure for vessel itself.
*2: Referred to Table 1 covered by ANNEX II of EC Directive
on Pressure Equipment Directive 97/23/EC
2.11 PED (Pressure Equipment (3) Operation

Directive)
CAUTION
(1) General
• The temperature and pressure of fluid should
• EJA series of pressure transmitters are
be applied under the normal operating
categorized as pressure accessories under the
condition.
vessel section of this directive 97/23/EC, which
• The ambient temperature should be applied
corresponds to Article 3, Paragraph 3 of PED,
under the normal operating condition.
denoted as Sound Engineering Practice (SEP).
• Please pay attention to prevent the
• EJA130A, EJA440A, EJA510A, and EJA530A
excessive pressure like water hammer,
can be used above 200 bar and therefore
etc. When water hammer is to be occurred,
considered as a part of a pressure retaining
please take measures to prevent the
vessel where category lll, Module H applies.
pressure from exceeding PS by setting the
These models with option code /PE3 conform
safety valve, etc. at the system and the like.
to that category.
• When external fire is to be occurred, please
(2) Technical Data take safety measures at the device or
• Models without /PE3 system not to influence the transmitters.
Article 3, Paragraph 3 of PED, denoted as
Sound Engineering Practice (SEP) .
• Models with /PE3
Module: H
Type of Equipment: Pressure Accessory-Vessel
Type of Fluid: Liquid and Gas
Group of Fluid: 1 and 2
IM 01C21C01-01E
2.12 Low Voltage Directive
Applicable standard: EN 61010-1
(1) Pollution Degree 2

“Pollution degree” describes the degree to
which a soild, liquid, or gas which deteriorates
dielectric strength or surface resistivity
is adhering. “2” applies to normal indoor
atmosphere. Normally, only non-conductive
pollution occurs. Occasionally, however,
temporary conductivity caused by condenstaion
must be expected.
(2) Installation Category I
“Overvoltage category (Installation category)”
describes a number which defines a transient
overvoltage condition. It implies the regulattion
for impulse withstand voltage. “I” applies to
electrical equipment which is supplied from the
circuit when appropriate transient overvoltage
control means (interfaces) are provided.
(3) Altitude of installation site:
Max. 2,000 m above sea level
(4) Indoor/Outdoor use
IM 01C21C01-01E
<3. Component Names> 3-1
3. Component Names
Terminal box cover
Tramsmitter sedtion
External indicator Conduit connection

conduit connection (Note 1)
CPU assembly
Zero-adjustment screw
Integral
indicator (Note 1)
Mounting screw
Process connection
(low pressure side)
Setting pin
(CN4)
Cover flange Process connector
Range-setting
(Note 1)
switch (Note 1)
(See Subsection 7.6) Pressure-detector section
Amplifier Cover Setting pin (CN4) Burn - out Output at

position (Note 2) direction burn - out
H
110% or
HIGH higher
L
H
-5% or
LOW lower
L
F0301.ai
Note 1: See Subsection 10.2, “Model and Suffix Codes,” for details.
Note 2: Insert the pin (CN4) as shown in the figure above to set the burn-out direction. The pin is set to the H side for delivery (unless
option code /C1 is specified in the order).
The setting can be confirmed by calling up parameter D52 using the BRAIN TERMINAL. Refer to Subsection 8.3.3 (11).
Figure 3.1 Component Names
Table 3.1 Display Symbol

Display Symbol Meaning of Display Symbol
The output signal being zero-adjusted is increasing.
The output signal being zero-adjusted is decreasing.
%, kPa, Pa, MPa, kgf/cm2, gf/cm2, mbar, bar,
Select one of these sixteen available engineering units for the display.
atm, mmHg, mmH2O, inH2O, inHg, ftH2O, psi, Torr
F0302.ai
IM 01C21C01-01E
<4. Installation> 4-1
4. Installation
4.1 Precautions 4.3 Rotating Transmitter Section
Before installing the transmitter, read the cautionary The DPharp transmitter section can be rotated in
notes in Section 2.4, “Selecting the Installation 90° segments.
Location.” For additional information on the ambient
1) Remove the two Allen screws that fasten the
conditions allowed at the installation location, refer
transmitter section and pressure-detector
to Subsection 10.1 “Standard Specifications.”
section, using the Allen wrench supplied with
the transmitter.
IMPORTANT 2) Rotate the transmitter section slowly in 90°
• When welding piping during construction, segments.
take care not to allow welding currents to 3) Tighten the two Allen screws.
flow through the transmitter.
• Do not step on this instrument after IMPORTANT
installation.
Do not rotate the transmitter section more than
• Never loosen the four screws securing the
180°.
cover flanges (if the seal liquid leaks, the
transmitter cannot be used).
Rotate 90° or 180° segments
Transmitter section
4.2 Mounting
The transmitter is mounted on a process using its
highpressure side flange as shown in Figure 4.1. Conduit connection
The customer should prepare the mating flange,
gasket, stud bolts and nuts. Zero-adjustment screw
Gasket
Pressure-detector section
F0402.ai
Figure 4.2 Rotating Transmitter Section
Stud bolt
Nut
F0401.ai
Figure 4.1 Transmitter Mounting
IMPORTANT
Please use a gasket which has a bigger inside
diameter than that of gasket facing (Ød) on
diaphragm seal. In case a gasket which has a
smaller inside diameter than that of gasket facing
is used, it may cause an error as the gasket
prevents diaphragm from working correctly.
(Refer to Subsection 10.4 ‘Dimensions’)
IM 01C21C01-01E
<4. Installation> 4-2
4.4 Changing the Direction of Teflon film
Integral Indicator
IMPORTANT
Always turn OFF power, release pressure and
remove a transmitter to non-hazardous area
Fluorinated oil
before disassembling and reassembling an [PART No. : F9145YN]
Diaphragm
indicator.
An integral indicator can be installed in the following

three directions. Follow the instructions in section
9.4 for removing and attaching the integral indicator.
Gasket area
PART No. Prosess Flange size
F9347XA 3 inch (80mm)
F0403.ai
F9347YD 2 inch (50mm)
Figure 4.3 Integral Indicator Direction F0403.ai
Figure 4.4 Affixing the Teflon Film
4.5 Affixing the Teflon Film

IMPORTANT
The FEP Teflon option includes a teflon film and
fluorinated oil. Before mounting the transmitter to
the process flange, affix the teflon film as follows:
1) Position the diaphragm so that the
diaphragm is in a upward position.
2) Pour the fluorinated oil on the diaphragm
and gasket area covering it completely and
evenly.
Be careful not to scratch the diaphragm or
change the its shape.
3) Affix the teflon film over the diaphragm and
gasket area.
4) Next, carefully inspect the cover and try
to identify any entrapped air between the
diaphragm and the teflon film. The air
must be removed to ensure accuracy. If air
pockets are present, use your fingers to
remove the air by starting at the center of the
diaphragm and work your way out.
5) Place the gasket with the teflon film and affix
to the process flange.
IM 01C21C01-01E
<5. Installing Impulse Piping> 5-1
5. Installing Impulse Piping

5.1 Impulse Piping Installation (2) Tightening the Process Connector
Mounting Bolts
Precautions
After connecting the impulse piping, tighten the
The impulse piping that connects the process
process connector mounting bolts uniformly.
outputs to the transmitter must convey the process
pressure accurately. If, for example, gas collects in (3) Removing the Impulse Piping Connecting
a liquidfilled impulse piping, or the drain of a gas- Port Dustproof Cap
filled impulse piping becomes plugged, the impulse
piping will not convey the pressure accurately. The impulse piping connecting port of the
Since this will cause errors in the measurement transmitter is covered with a plastic cap to exclude
output, select the proper piping method for the dust. This cap must be removed before connecting
process fluid (gas, liquid, or steam). Pay careful the piping. (Be careful not to damage the threads
attention to the following points when routing the when removing this cap. Never insert a screwdriver
impulse piping and connecting the impulse piping to or other tool between the cap and port threads to
the transmitter. remove the cap.)
5.1.1 Connecting Impulse Piping to the 5.1.2 Routing the Impulse Piping
Transmitter
(1) Impulse Piping Slope
(1) Check the High and Low Pressure The impulse piping must be routed with only an
Connections on the Transmitter (Figure 5.1) upward or downward slope. Even for horizontal
Symbols “H” and “L” are shown on a capsule routing, the impulse piping should have a slope of
assembly to indicate high and low pressure side. at least 1/10 to prevent condensate (or gases) from
For liquid level measurement in an open tank, the ‘L’ accumulating in the pipes.
(low pressure) side is used to refer atmosphere. For
(2) Preventing Freezing
a closed tank, connect the impulse line to the low
pressure side of the transmitter. This will refer the If there is any risk that the process fluid in the
pressure in the tank. impulse piping or transmitter could freeze, use a
steam jacket or heater to maintain the temperature
of the fluid.
“H” and “L” are shown
NOTE
Low pressure
connection After completing the connections, close the
Process connector
valves on the process pressure taps (main
valves), the valves at the transmitter (stop
Bolt
valves), and the impulse piping drain valves,
F0501.ai so that condensate, sediment, dust and other
extraneous material cannot enter the impulse
Figure 5.1 “H” and “L” Symbols on a Capsule
Assembly
piping.
IM 01C21C01-01E
<5. Installing Impulse Piping> 5-2
5.2 Impulse Piping Connection
Examples
Figure 5.2 shows examples of typical impulse
piping connections. Before connecting the
transmitter to the process, study the transmitter
installation location, the process piping layout,
and the characteristics of the process fluid
(corrosiveness, toxicity, flammability, etc.), etc. and
make appropriate changes and additions to the
connection configurations.
Open Tank
Pipe (opened to atmosphere

at low pressure side)
Closed Tank
Tap valve
Union or flange
Vent plug
Tee
Drain valve
Drain plug
F0502.ai
Figure 5.2 Impulse Piping Connection Examples
IM 01C21C01-01E
<6. Wiring> 6-1
6. Wiring
6.1 Wiring Precautions 6.3 Connections of External
Wiring to Terminal Box
IMPORTANT
• Lay wiring as far as possible from electrical
6.3.1 Power Supply Wiring Connection
noise sources such as large capacity Connect the power supply wiring to the SUPPLY +
transformers, motors, and power supplies. and – terminals.
• Remove electrical connection dust cap
Transmitter terminal box
before wiring. +
• All threaded parts must be treated with Power supply
waterproofing sealant. (A non-hardening –
silicone group sealant is recommended.)

• To prevent noise pickup, do not pass signal F0601.ai
and power cables through the same ducts. Figure 6.1 Power Supply Wiring Connection
• Explosion-protected instruments must
be wired in accordance with specific 6.3.2 External Indicator Connection
requirements (and, in certain countries,
legal regulations) in order to preserve the Connect wiring for external indicators to the CHECK
effectiveness of their explosion-protected + and – terminals.
features. (Note) Use a external indicator whose internal resistance is 10Ω
or less.
• The terminal box cover is locked by an Allen
head bolt (a shrouding bolt) on CENELEC External indicator
Power supply
and IECEx flameproof type transmitters. +
When the shrouding bolt is driven clockwise
–
by an Allen wrench, it is going in and cover
lock is released, and then the cover can
be opened by hand. See Subsection 9.4
“Disassembly and Reassembly” for details. F0602.ai
Figure 6.2 External Indicator Connection
6.2 Selecting the Wiring 6.3.3 BRAIN TERMINAL BT200

Materials Connection
(a) Use stranded leadwires or cables which are Connect the BT200 to the SUPPLY + and
the same as or better than 600 V grade PVC – terminals (Use hooks). The communication line
insulated wire (JIS C3307) or equivalent. requires a reception resistor of 250 to 600Ω in
(b) Use shielded wires in areas that are susceptible series.
to electrical noise. Transmitter terminal box Power supply
(c) In areas with higher or lower ambient +
temperatures, use appropriate wires or cables. –
(d) In environment where oils, solvents, corrosive
Ignore the polarity
gases or liquids may be present, use wires or since the BT200 is
cables that are resistant to such substances. AC-coupled to the
BT200 terminal box.
(e) It is recommended that crimp-on solderless
F0603.ai
terminal lugs (for 4 mm screws) with insulating
Figure 6.3 BT200 Connection
sleeves be used for leadwire ends.
IM 01C21C01-01E
<6. Wiring> 6-2
6.3.4 Check Meter Connection (2) Intrinsically Safe Type
Connect the check meter to the CHECK + and For intrinsically safe type, a safety barrier must be
– terminals (use hooks). included in the loop.
• A 4 to 20 mA DC output signal from the CHECK Hazardous Location Nonhazardous Location
+ and – terminals.
(Note) Use a check meter whose internal resistance is 10Ω or Transmitter terminal box
less. Distributor
(Power supply unit)
Power supply
+ Receiver
instrument
– +
–
Check meter
Transmitter terminal box Safety barrier
F0604.ai F0606.ai
Figure 6.4 Check Meter Connection Figure 6.6 Connection between Transmitter and
Distributor
6.4 Wiring 6.4.2 Wiring Installation
6.4.1 Loop Configuration (1) General-use Type and Intrinsically Safe

Type
Since the DPharp uses a two-wire transmission
system, signal wiring is also used as power wiring. Make cable wiring using metallic conduit or
waterproof glands.
DC power is required for the transmitter loop. The
transmitter and distributor are connected as shown • Apply a non-hardening sealant to the terminal
below. box connection port and to the threads on the
flexible metal conduit for waterproofing.
For details of the power supply voltage and load
resistance, see Section 6.6; for communications
line requirements, see Subsection 8.1.2.
(1) General-use Type and Flameproof Type Flexible metal conduit
Apply a non-hardening
Wiring metal sealant to the threads
conduit for waterproofing.
Distributor Tee
(Power supply unit)
Drain plug
F0607.ai
Receiver Figure 6.7 Typical Wiring Using Flexible Metal

instrument Conduit
+
–
F0605.ai
Figure 6.5 Connection between Transmitter and

Distributor
IM 01C21C01-01E
<6. Wiring> 6-3
(2) Flameproof Type 6.5 Grounding
Wire cables through a flameproof packing adapter, Grounding is always required for the proper
or using a flameproof metal conduit. operation of transmitters. Follow the domestic
■ Wiring cable through flameproof packing adapter. electrical requirements as regulated in each
• Apply a nonhardening sealant to the terminal country. For a transmitter with built-in lightning
box connection port and to the threads on the protector, grounding should satisfy ground
flameproof packing adapter for waterproofing. resistance of 10Ω or less.
Ground terminals are located on the inside and
outside of the terminal box. Either of these terminals
Flameproof packing adapter may be used.
Flexible metal conduit Transmitter terminal box
Wiring metal Apply a non-hardening Ground terminal

conduit sealant to the threads (Inside)
for waterproofing.
Tee
Drain plug
F0608.ai
Figure 6.8 Typical Cable Wiring Using Flameproof

Packing Adapter
Ground terminal
(Outside)
■ Flameproof metal conduit wiring
• A seal fitting must be installed near the terminal
F0610.ai
box connection port for a sealed construction.
• Apply a non-hardening sealant to the threads of Figure 6.10 Ground Terminals
the terminal box connection port, flexible metal
conduit and seal fitting for waterproofing.
6.6 Power Supply Voltage and
Gas sealing device
Non-hazardous area Load Resistance
When configuring the loop, make sure that the
Flameproof flexible
metal conduit external load resistance is within the range in the
Hazardous area figure below.
Apply a non-hardening (Note) In case of an intrinsically safe transmitter, external load
Flameproof
sealant to the threads resistance includes safety barrier resistance.
heavy-gauge
of these fittings for
steel conduit
waterproofing
600
Tee Seal fitting
Drain plug After wiring, impregnate the fitting External E–10.5
with a compound to seal tubing. load R= Communication
0.0236
F0609.ai resistance applicable range
R (Ω) BRAIN and HART
Figure 6.9 Typical Wiring Using Flameproof Metal
Conduit
250
0 10.5 16.4 24.7 42

Power supply voltage E (V DC)
F0611.ai
Figure 6.11 Relationship between Power Supply

Voltage and External Load Resistance
IM 01C21C01-01E
<7. Operation> 7-1
7. Operation
7.1 Preparation for Starting  Confirming that Transmitter is Operating
Properly
Operation
The Model EJA210A and EJA220A flange mounted Using the BT200
differential pressure transmitter measures the levels
• If the wiring system is faulty, ‘communication
or densities of liquids. This section describes the
error’ appears on the display.
operation procedure for the EJA210A as shown in
• If the transmitter is faulty, ‘SELF CHECK
Figure 7.1 when measuring a liquid level in an open
ERROR’ appears on the display.
tank.
PARAM
C60:SELF CHECK
(a) Confirm that there is no leak in the connecting ERROR
part of the transmitter mounting flange. communication error
Remove the plastic dust cap placed in the

process connector (low pressure side). DATA DIAG PRNT ESC
(b) Turn ON power and connect the BT200. Communication error Self-diagnostic error
Open the terminal box cover and connect the (Faulty wiring) (Faulty transmitter)
F0702.ai
BT200 to the SUPPLY + and – terminals.
(c) Using the BT200, confirm that the transmitter is Using the integral indicator
operating properly. Check parameter values or
change the setpoints as necessary. • If the wiring system is faulty, the display stays
For BT200 operating procedures, see Chapter blank.
8. If the transmitter is equipped with an integral • If the transmitter is faulty, an error code will
indicator, its indication can be used to confirm appear on the display according to the nature of
that the transmitter is operating properly. the error.
Open tank
Self-diagnostic error on
the integral indicator
(Faulty transmitter)
F0703.ai
NOTE
If any of the error indications above appears on
the display of the integral indicator or BT200,
refer to Subsection 8.5.2 for corrective action.
 Verify and Change Transmitter

F0701.ai Parameter Setting and Values
Figure 7.1 Liquid Flow Measurement
The following parameters are the minimum settings
required for operation. The transmitter has been
shipped with these parameters. To confirm or
change the values, see Subsection 8.3.3.
• Measuring range … See Subsection 8.3.3 (2)
• Operation mode … See Subsection 8.3.3 (8)
IM 01C21C01-01E
<7. Operation> 7-2
7.2 Zero Point Adjustment 7.2.1 When you can obtain Low Range
Value from actual measured value of
Adjust the zero point after operating preparation is
0% (0 kPa, atmospheric pressure);
completed.
IMPORTANT  Using the Transmitter Zero-adjustment

Screw
Do not turn off the power to the transmitter
Before adjusting a screw, check that the parameter
immediately after a zero adjustment. Powering
J20: EXT ZERO ADJ displays ENABLE. See
off within 30 seconds after a zero adjustment
Subsection 8.3.3 (12) for the setting procedure.
will return the adjustment back to the previous
settings. Use a slotted screwdriver to turn the zero-
adjustment screw. Turn the screw clockwise
The zero point adjustment can be made in either to increase the output or counterclockwise to
way: using the zero-adjustment screw of the decrease the output. The zero point adjustment
transmitter or the BT200 operation. can be made with a resolution of 0.01% of the
setting range. Since the degree of zero adjustments
For output signal checking, display the parameter
varies with the screw turning speed, turn the screw
A10: OUTPUT (%) in the BT200.
slowly for fine adjustment and quickly for coarse
 BT200 adjustment.
PARAM Output signal (%)
A10:OUTPUT(%)
0.0 %
A11:ENGR OUTPUT
display  Using the BT200
A20:AMP TEMP Zero point can be adjusted by simple key operation
of the BT200.
DATA DIAG PRNT ESC
Select parameter J10: ZERO ADJ, and press the
 Zero-adjustment Screw ENTER key twice. The zero point will be adjusted
automatically to the output signal 0% (4 mA DC).
Confirm that the setting value displayed for the
parameter is ‘0.0%’ before pressing the ENTER
key. See Subsection 8.3.3 (12) for BT200 operating
procedures.
Zero-adjustment screw SET A display when parameter
J10:ZERO ADJ
-0.0 % J10 is selected.
F0704.ai
+ 000.0
Press key
When adjusting the transmitter zero point, the liquid twice for 0% output 4 mA DC.
level in a tank does not have to be set to the low CLR ESC
limit (0%) of the measuring range. In such case, F0705.ai
match the transmitter output signal with the actual

measured value using a glass gauge, for example.
IM 01C21C01-01E
<7. Operation> 7-3
7.2.2 When you cannot obtain Low Range 7.3 Starting Operation
Value from actual measured value of
After completing the zero point adjustment, follow
0%;
the procedure below to start operation.
Convert the actual measured value obtained by a
1) Confirm the operating status.
glass gauge into %.
The output signal may widely fluctuate (hunting
[Example] state) due to process pressure periodic
variation. In such case, BT200 operation can
The measuring range of 0 to 2 m and the actual dampen the transmitter output signal. Confirm
measured value of 0.8 m. the hunting state using a receiving instrument
0.8 or the integral indicator and set the optimum
Actual measured value = x 100 = 40.0% damping time constant. See Subsection 8.3.3
2
(3) “Damping time constant setup.”
2) After confirming the operating status, perform
 Using the Transmitter Zero-Adjustment the following:
Screw
Turn the screw to match the output signal to the IMPORTANT
actual measured value in %.
• Remove the BT200 from the terminal box,
 Using the BT200 and confirm that none of the terminal screws
are loosened.
Select the parameter J10: ZERO ADJ. Change • Close the terminal box cover and the
the set point (%) displayed for the parameter to the amplifier cover. Screw each cover in tightly
actual measured value (%), and press the ENTER until it will not turn further.
key twice. • Two covers are required to be locked on
See Subsection 8.3.3 (12) for operation details. the CENELEC and IECEx Flameproof type
SET A display at J10 transmitters. An Allen head bolts (shrouding
J10:ZERO ADJ
-0.0 % bolts) are provided under edge of the
+ 000.0
each cover for locking. When a shrouding
bolts are driven counterclockwise by an
CLR ESC
Allen wrench, it is coming out and locks
up a cover. (See page 9-3) After locking,
the covers should be confirmed not to be
SET Change setting to the actually
J10:ZERO ADJ opened by hand.
-0.0 % measured value (40.0%). • Tighten the zero-adjustment cover mounting
+ 040.0
Press key twice screw to fix the cover in position.
for 40% output 10.4 mA DC.
CLR ESC
F0706.ai
IM 01C21C01-01E
<7. Operation> 7-4
7.4 Shutting Down Operation 7.5.2 Venting Gas
Turn off the power. 1) Gradually open the vent screw to vent gas from
the transmitter pressur-detector section. (See
NOTE Figure 7.2)
2) When the transmitter is completely vented,
Whenever shutting down the transmitter for a close the vent screw.
long period, detach the transmitter from the tank. 3) Tighen the vent screw to a torque of 10 N·m.
7.5 Venting or Draining

Transmitter Pressure-
detector Section Drain plug
Since this transmitter is designed to be self-
draining and self-venting with vertical impulse
piping connections, neither draining nor venting Vent screw
will be required if the impulse piping is configured When you loosen the drain plug or the vent screw, the
accumulated liquid (or gas) will be expelled in the direction
appropriately for self-draining or self-venting of the arrow.
operation. F0707.ai
Figure 7.2 Draining/Venting the Transmitter

If condensate (or gas) collects in the transmitter
pressure-detector section, the measured pressure
may be in error. If it is not possible to configure the
piping for self-draining (or self-venting) operation, 7.6 Setting the Range Using the
you will need to loosen the drain (vent) screw on the Range-setting Switch
transmitter to completely drain (vent) any stagnated
With actual pressure being applied to the
liquid (gas).
transmitter, the range-setting switch (push-button)
However, since draining condensate or bleeding off located on the optional integral indicator plate and
gas gives the pressure measurement disturbance, the external zero-adjustment screw allow users to
this should not be done when the loop is in change (re-range) the low- and high-limit values for
operation. the measurement range (LRV and HRV) without
using BT200. However, other changes in the
WARNING display settings (scale range and engineering unit)
for the integral indicator requires BT200.
Since the accumulated liquid (or gas) may be Follow the procedure below to change the LRV and
toxic or otherwise harmful, take appropriate care HRV settings.
to avoid contact with the body, or inhalation of
vapors. [Example]
Rerange LRV to 0 and HRV to 3 MPa.
7.5.1 Draining Condensate 1) Connect the transmitter and apparatus as
1) Gradually open the drain plug and drain the shown in Figure 9.1 and warm up for at least
transmitter pressure-detector section. (See five minutes.
Figure 7.2) 2) Press the range-setting push-button. The
2) When all accumulated liquid is completely integral indicator then displays “LSET.”
removed, close the drain plug. 3) Apply a pressure of 0 kPa (atmospheric
3) Tighten the drain plug to a torque of 34 to 39 pressure) to the transmitter. (Note 1)
N·m.
IM 01C21C01-01E
<7. Operation> 7-5
4) Turn the external zero-adjustment screw in the Integral indicator
desired direction. The integral indicator displays
the output signal in %. (Note 2) Note : Use a thin bar which
has a blunt tip, e.g.,
5) Adjust the output signal to 0% (1 V DC) by a hexagonal wrench,
rotating the external zero-adjustment screw. to press the range-
setting push-button
Doing so completes the LRV setting.
6) Press the range-setting push-button. The
integral indicator then displays “HSET.”
Range-setting switch
7) Apply a pressure of 3 MPa to the transmitter. (Push-button)
(Note 1) F0708.ai
8) Turn the external zero-adjustment screw in the Figure 7.3 Range-setting Switch
desired direction. The integral indicator displays
the output signal in %. (Note 2)
9) Adjust the output signal to 100% (5 V DC) by
rotating the external zero-adjustment screw.
Doing so completes the HRV setting.
10) Press the range-setting push-button. The
transmitter then switches back to the normal
operation mode with the measurement range of
0 to 3 MPa.
Note 1: Wait until the pressure inside the pressure-detector
section has stabilized before proceeding to the next step.
Note 2: If the pressure applied to the transmitter exceeds the
previous LRV (or HRV), the integral indicator may display
error number “Er.07” (In this case, the output signal
percent and “Er.07” are displayed alternately every two
seconds).
Although “Er.07” is displayed, you may proceed to the
next step. However, should any other error number be
displayed, take the appropriate measure in reference to
Subsection 8.5.2, “Errors and Countermeasures.”
IMPORTANT
• Do not turn off the power to the transmitter
immediately after completion of the change
in the LRV and/or HRV setting(s). Note
that powering off within thirty seconds after
setting will cause a return to the previous
settings.
• Changing LRV automatically changes HRV
to the following value.
HRV =
previous HRV + (new LRV – previous LRV)
• If the range-setting push-button and external
zero-adjustment screw are not touched
during a range-change operation, the
transmitter automatically switches back to
the normal operation mode.
IM 01C21C01-01E
<8. BRAIN TERMINAL BT200 Operation> 8-1
8. BRAIN TERMINAL BT200 Operation

The DPharp is equipped with BRAIN • Note for Connecting the BT200
communications capabilities, so that range
changes, Tag No. setup, monitoring of self- IMPORTANT
diagnostic results, and zero point adjustment can
be handled by remote control via BT200 BRAIN • Analog output may change temporally in
TERMINAL or CENTUM CS console. This section connecting with BRAIN terminal due to
describes procedures for setting parameters using an initial current flowed to it. To prevent
the BT200. For details concerning the BT200, see communication signal affecting the upper
IM 01C00A11-01E, “BT200 User’s Manual.” system, it is recommended to install a low-
pass filter (approximately 0.1s).
• Communication signal is superimposed on
8.1 BT200 Operation analog output signal. It is recommended
to set a low-pass filter (approximately
Precautions
0.1s) to the receiver in order to reduce the
8.1.1 Connecting the BT200 output effect from communication signal.
Before online-communication, confirm that
Connection to the transmitter with the BT200 communication signal does not give effect on
can be made by either connecting to the BT200 the upper system.
connection hooks in the transmitter terminal box or
by connecting to a relaying terminal board.
8.1.2 Conditions of Communication Line
• Communication Line Requirements

Control room [Protocol specification] Yokogawa original
Relaying
terminals protocol
Terminal board
[Modulation] Burst modulation
0: 2400Hz
Distributor 1: Signal without carrier
[Baud rate] 1200bps
[Communication signal]
host to device: +/- 0.5V (load resistance 250Ω)
F0801.ai device to host: +/- 2mA
Figure 8.1 Connecting the BT200 Cable resistance Rc
Power
supply
cc
Load Cable DPharp

resistance R resistance Rc
● Loop resistance = R + 2Rc

= 250 to 600Ω
● Loop capacitance = 0.22 µF max. BT200
F0802.ai
Figure 8.2 Conditions of Communication Line
IM 01C21C01-01E
8.2 BT200 Operating Procedures 8.2.2 Operating Key Functions
8.2.1 Key Layout and Screen Display (1) Alphanumeric Keys and Shift Keys
Figure 8.3 shows the arrangement of the operating You can use the alphanumeric keys in conjunction
with the shift keys to enter symbols, as well as
keys on the BT200 keypad, and Figure 8.4 shows
alphanumeric keys.
the BT200 screen component.
LCD Alphanumeric keys

(21 character × 8 lines)
Shift keys F0805.ai
Function keys a. Entering Digits, Symbols, and Spaces

Simply press the alphanumeric keys.
Movement keys
Entry Key-in Sequence
ENTER key
–4
Power ON/OFF key 0.3
1 –9
Alphanumeric keys F0806.ai
b. Entering Letters (A through Z)

Press an alphanumeric key following a shift key to
Shift keys
enter the letter shown on that side which the shift
F0803.ai
key represents. You must press the shift key before
Figure 8.3 BT200 Key Layout
entering each letter.
MENU SCREEN Left-side letter on the Right-side letter on
Messages
MENU BATTERY alphanumeric key the alphanumeric key
A:DISPLAY
B:SENSOR TYPE
Menu choices
Screen title
HOME SET ADJ ESC
W
PARAMETER SCREEN
PARAM IC
A10:OUTPUT Function
100.0 %
Parameters A11:ENGR. OUTPUT commands J. B
1000 mmH20
A20:AMP TEMP F0807.ai
23 deg C
DATA DI AG PRNT
Use the function key [F2] CAPS to select between
F0804.ai
uppercase and lowercase (for letters only). The
Figure 8.4 BT200 Screen Component
case toggles between uppercase and lowercase
each time you press [F2] CAPS.
Entering uppercase Entering lowercase

CODE CAPS CLR ESC CODE caps CLR ESC

to lower case
Boy
(B) (o) (y)
F0808.ai
IM 01C21C01-01E
Use the function key [F1] CODE to enter symbols.

The following symbols will appear in sequence, one
at a time, at the cursor each time you press [F1]
CODE:
/ . − , + * ) ( ’ & % $ # ” !
To enter characters next to these symbols, press [>]
to move the cursor.
symbol command
l/m
(I) (/) (m)
F0809.ai
(2) Function Keys

The functions of the function keys depend on the
function commands on display.
MENU
A:DISPLAY
B:SENSOR TYPE
HOME SET ADJ ESC Function commands
Function keys
F0810.ai
Function Command List

Command Function
ADJ Displays the ADJ menu
CAPS/caps Selects uppercase or lowercase
CODE Selects symbols
CLR Erases input data or deletes all data
DATA Updates parameter data
DEL Deletes one character
DIAG Calls the self-check panel
ESC Returns to the most recent display
HOME Displays the menu panel
NO Quits setup and returns to the previous
display
OK Proceeds to the next panel
PARM Enters the parameter number setup mode
SET Displays the SET menu
SLOT Returns to the slot selection panel
UTIL Calls the utility panel
*COPY Prints out parameters on display
*FEED Paper feed
*LIST Lists all parameters in the menu
*PON/ Automatic printout mode on or off
POFF
*PRNT Changes to the print mode
*GO Starts printing
*STOP Cancels printing
* Available on BT200-P00 (with printer).
IM 01C21C01-01E
8.2.3 Calling Up Menu Addresses Using the Operating Keys
--WELCOME-- UTILITY The utility screen contains the

BRAIN TERMINAL 1.ID following items.
ID: BT200 2.SECURITY CODE
STARTUP 3.LANGUAGE SELECT 1. BT200 ID settings
SCREEN check connection 4.LCD CONTRAST 2. Security code settings
push ENTER key 5.PRINTER ADJUST
3. Switching language of messages
UTIL FEED esc (Japanese or English)
4. LCD contrast setting
5. Adjusting printout tone
(UTIL)
(BT200-P00 only)
PARAM
01:MODEL
EJA210A-DM
INITIAL 02:TAG NO. FUNC
DATA YOKOGAWA 1.MENU
SCREEN 03:SELF CHECK (ESC) 2.UPLOAD TO BT200
GOOD 3.DOWNLOAD TO INST
OK 4.PRINT ALL DATA
HOME SET ADJ ESC
(SET) (ADJ)
(HOME MENU SCREEN) (SET MENU SCREEN) (ADJ MENU SCREEN)
MENU MENU MENU
A.DISPLAY C.SETTING J.ADJUST
B.SENSOR TYPE D.AUX SET 1 K.TEST
MENU E.AUX SET 2 M.MEMO
SCREEN H:AUTO SET P:RECORD
HOME SET ADJ ESC HOME SET ADJ ESC HOME SET ADJ ESC
PARAM PARAM
A60:SELF CHECK C60:SELF CHECK
GOOD GOOD
PARAM PARAM PARAM

A21:CAPSULE TEMP C22:HIGH RANGE J60:SELF CHECK
PARA- 26.5 deg C 100 kPa GOOD
METER DATA DIAG PRNT ESC DATA DIAG PRNT ESC
SCREEN
PARAM PARAM PARAM
A10:OUTPUT(%) C10:TAG NO. J10:ZERO ADJ
50.0 % YOKOGAWA 0.0 %
DATA DIAG
A11:ENGR, PRNT
OUTPUT ESC DATA DIAG
C20:PRESS UNITPRNT ESC DATA DIAG
J11:ZERO DEV PRNT ESC
20.0 M kPa 22.2 %
A20:AMP TEMP C21:LOW RANGE J20:EXT. ZERO ADJ
24.5 deg C 0 kPa ENABLE
DATA DIAG PRNT ESC DATA DIAG PRNT ESC DATA DIAG PRNT ESC
SET See “BT200 Instruction Manual” for details

C10:TAG NO. concerning uploading and downloading parameters
SETUP YOKOGAWA
SCREEN YOKOGAWA and printouts (BT200-P00).
CODE CAPS CLR ESC

F0811.ai
IM 01C21C01-01E
8.3 Setting Parameters Using the BT200
8.3.1 Parameter Summary
Instruments to which applicable:
F: Differential pressure transmitters EJA110A, EJA120A, and EJA130A
P: Pressure transmitters EJA310A, EJA430A, EJA440A, EJA510A, and EJA530A
L: Liquid level transmitters EJA210A and EJA220A
Applica-
Rewrita- bility
No. Item Description Remarks Default Value
bility
F P L
01 MODEL Model+capsule type –   
02 TAG NO. Tag number – 16 alphanumerics   
03 SELF CHECK Self-diagnostic result – GOOD/ERROR   
A DISPLAY Measured data display – Menu name   
A10 OUTPUT (%) Output (in %) – –5 to 110%*3   
A11 ENGR. OUTPUT Output (in engineering units) – –19999 to 19999   
A20 AMP TEMP Amplifier temperature – Unit specified in D30   
A21 CAPSULE Capsule temperature – Unit specified in D30   
TEMP
A30 STATIC PRESS Static pressure – Unit specified in D31*1  – 
A40 INPUT Input (indicated as the value – –32000 to 32000   
after zeroing)
A60 SELF CHECK Self-diagnostic messages – GOOD/ERROR, CAP MODULE FAULT, AMP   
MODULE FAULT, OUT OF RANGE, OUT OF SP
RANGE*1, OVER TEMP (CAP), OVER TEMP (AMP),
OVER OUTPUT, OVER DISPLAY, ILLEGAL LRV,
ILLEGAL HRV, ILLEGAL SPAN, and ZERO ADJ OVER
B SENSOR TYPE Sensor type – Menu name   
B10 MODEL Model+span – 16 uppercase alphanumerics   
B11 STYLE NO. Style number –   
B20 LRL Lower range-limit – –32000 to 32000   
B21 URL Upper range-limit – –32000 to 32000   
B30 MIN SPAN Minimum span – –32000 to 32000   
B40 MAX STAT.P. Maximum static pressure*6 –  – 
B60 SELF CHECK Self-diagnostic messages – Same as A60   
C SETTING Setting data – Menu name   
C10 TAG. NO. Tag number  16 alphanumerics As specified when   
ordered.
C20 PRESS UNIT Measurement range units  Selected from mmH2O, As specified when   
mmAq, mmWG, mmHg, Torr, ordered.
Pa, hPa, kPa, MPa, mbar, bar,
gf/cm2, kgf/cm2, inH2O, inHg,
ftH2O, psi, or atm
C21 LOW RANGE Measurement range, lower  –32000 to 32000(but within As specified when   
range value measurement range) ordered.
C22 HIGH RANGE Measurement range, higher  –32000 to 32000(but within As specified when   
range value measurement range) ordered.
C30 AMP DAMPING Damping time constant  Selected from 0.2*2, 0.5, 1.0, 2.0 s   
2.0, 4.0, 8.0, 16.0, 32.0, or
64.0 sec.
C40 OUTPUT MODE Output mode and integral  Selected from OUT:LIN; DSP: As specified when  – –
indicator mode LIN, OUT:LIN; DSP:SQR, ordered.
OUT:SQR; DSP:SQR If not specified, OUT:
LIN; DSP: LIN.
C60 SELF CHECK Self-diagnostic messages – Same as A60   
IM 01C21C01-01E
Applica-
Rewrita- bility
bility
F P L
D AUX SET 1 Auxiliary setting data 1 – Menu name   
D10 LOW CUT Low cut  0.0 to 20.0% 10.0%   
D11 LOW CUT Low cut mode  LINEAR/ZERO LINEAR   
MODE
D15 OUT LIMIT(L) Lower output range-limit  –5.0 to 110.0% –5.0%*7   
D16 OUT LIMIT(H) Upper output range-limit  –5.0 to 110.0% 110.0%   
D20 DISP SELECT Display selection  NORMAL %/USER SET, As specified when   
USER & %/INP PRES, PRES ordered.
&%
D21 DISP UNIT Engineering unit for display  8 uppercase alphanumerics   
D22 DISP LRV Engineering range, lower  –19999 to 19999 As specified when   
range value ordered.
D23 DISP HRV Engineering range, higher  –19999 to 19999 As specified when   
range value ordered.
D30 TEMP UNIT Temperature setting units  deg C/deg F deg C   
D31 STAT. P. UNIT Static pressure setting units  Selected from mmH2O, As specified when  – 
mmAq, mmWG, mmHg, Torr, ordered. If not
Pa, hPa, kPa, MPa, mbar, bar, specified, MPa.
gf/cm2, kgf/cm2, inH2O, inHg,
ftH2O, psi, or atm
D40 REV OUTPUT Output reversal  NORMAL/REVERSE If not specified,   
NORMAL.
D45 H/L SWAP Impulse piping accessing  NORMAL/REVERSE*4 NORMAL  – –
direction
D52 BURN OUT CPU error – HIGH/LOW, –5 to 110%*3 HIGH   
D53 ERROR OUT Hardware error  HOLD/HIGH/LOW, HIGH   
–5 to 110%*3
D60 SELF CHECK Self-diagnostic messages – Same as A60   
E AUX SET 2 Auxiliary setting data 2 – Menu name   
E10 DFS MODE DFS mode  OFF/ON*5 ON   –
E14 TEMP SELECT Reference temperature  AMP. TEMP/CAP. TEMP*5 CAP. TEMP   –
sensor
E15 TEMP ZERO Zero shift conpensation  ±10.00*5 0.00   –
setup
E30 BI DIRE MODE Bidirectional mode  OFF/ON OFF  – –
E50 AUTO Auto-recover from sensor  OFF/ON ON   
RECOVER error
E60 SELF CHECK Self-diagnostic messages – Same as A60   
H AUTO SET Automatic setup – Menu name   
H10 AUTO LRV Automatic measurement  –32000 to 32000 Displays the same   
range lower range value data as C21.
setup
H11 AUTO HRV Automatic measurement  –32000 to 32000 Displays the same   
range higher range value data as C22.
setup
H60 SELF CHECK Self-diagnostic messages – Same as A60   
J ADJUST Adjustment data – Menu name   
J10 ZERO ADJ Automatic zero adjustment  –5 to 110.0%*3   
J11 ZERO DEV. Manual zero adjustment    
J15 SPAN ADJ Manual span adjustment  –10.00 to 10.00% 0.00%   
J20 EXT. ZERO ADJ External zero-adjustment  ENABLE/INHIBIT   
screw permission
J30 AOUTPUT 4mA 4mA adjustment  –10.00 to 10.00% 0.00%   
J31 OUTPUT 20mA 20mA adjustment  –10.00 to 10.00% 0.00%   
J60 ASELF CHECK Self-diagnostic messages – Same as A60   
K TEST Tests – Menu name   
K10 OUTPUT in % Test output % setting  –5 to 110.0%*3 Displays   
‘ACTIVE’ while executing
K60 SELF CHECK Self-diagnostic messages – Same as A60   
IM 01C21C01-01E
Applica-
Rewrita- bility
bility
F P L
M MEMO Memo – Menu name   
M10 MEMO 1 Memo  8 uppercase alphanumerics   
M60 SELF CHECK Self-diagnostic messages – Same as A60   
P RECORD History of the errors –   
P10 ERROR REC 1 Last error  Display the error   
P11 ERROR REC 2 One time before  Display the error   
P12 ERROR REC 3 Two time before  Display the error   
P13 ERROR REC 4 Three time before  Display the error   
P60 SELF CHECK Self-diagnostic messages – Same as A60   
*1: In case of Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
*2: When Optional code /F1 is specified, substitute the value with 0.1.
*3: When Optional code /F1 is specified, substitute the value –5 with –2.5.
*4: Not applicable for Model EJA115.
*5: Applicable only for Model EJA118W, EJA118N, EJA118Y, EJA438W, and EJA438N.
*6: See MWP(max. working pressure) on the nameplate. B40 shows an approximate value of maximum pressure for the capsule.
*7: Unless otherwise specified by order. When optional code /F1 is specified, substitute the value –5 with –2.5.
IM 01C21C01-01E
8.3.2 Parameter Usage and Selection
IMPORTANT
Before describing the procedure for setting
parameters, we present the following table showing If the transmitter is turned off within 30 seconds
how the parameters are used and in what case. after parameters have been set, the set data
will not be stored and the terminal returns to
previous settings.
Table 8.1 Parameter Usage and Selection

Setup Item Description
Tag No. setup Sets the Tag No. (using 16 alphanumeric characters).
P. 8-9 Note: Up to 8 alphanumerics (upper case letters) can be used in the BT100.
Calibration range setup Sets the calibration range for 4 to 20 mA DC. Sets three data items: range unit, input
P. 8-9 value at 4 mA DC (LRV), and input value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5 digits (excluding any
decimal point) within the range of –32000 to 32000.
Damping time constant setup Adjusts the output response speed for 4 to 20 mA DC.
P. 8-10 Can be set in 9 increments from 0.2 to 64 s.
Output signal low cut mode Used mainly to stabilize output near 0% if output signal is the square root mode.
setup Two modes are available: forcing output to 0% for input below a specific value, or
P. 8-11 changing to proportional output for input below a specific value.
Change the output limits Change the range of normal output.
P. 8-11
Integral indicator scale range Sets the following 5 types of integral indicator scale ranges and units:
and unit setup % scale indicator, user set scale indicator, alternate indication of user set scale and
P. 8-11 % scale, input pressure display, alternate indication of input pressure and % scale
When using the user set scale, 4 types of data can be set:
user set scale setting, unit (BT200 only), display value at 4 mA DC (LRV), and
display value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5 digits (excluding any
decimal point) within the range of –19999 to 19999.
Unit setup for displayed Sets a unit for temperatures displayed on the BT200.
temperature
P. 8-13
Unit setup for displayed static Sets a unit for static pressure displayed on the BT200.
pressure
P. 8-13
Operation mode (normal/ Reverses the direction for 4 to 20 mA DC output relative to input.
reverse signal) setup Reverse mode is used for applications in which safety requires that output be driven
P. 8-13 toward 20 mA if input is lost.
Output status display/setup Displays the status of 4 to 20 mA DC output when a CPU failure. The parameter of the
when a CPU failure standard unit is fixed to the high limit value.
P. 8-14
Output status setup when a Sets the status of the 4 to 20 mA DC output when an abnormal status is detected
hardware error occurs with the capsule or the amplifier as the result of self-diagnosis. One of the following
P. 8-14 statuses; last held, high limit, and low limit values, can be selected.
Range change (while applying Range for 4 to 20 mA DC signal is set with actual input applied. Sets 20 mA DC output
actual inputs) precisely with respect to user’s reference instrument output. Note that DPharp is
P. 8-14 calibrated with high accuracy before shipment, so span should be set using the normal
range setup.
Zero point adjustment Adjusts zero point. This can be done either using the external zero-adjustment screw
P. 8-15 on the transmitteror using the BT200.
Span adjustment Adjust the characterization curve. All the transmitters are calibrated at factory and this
P. 8-16 adjustment is normally not necessary for most cases. Use for specific purposes.
Test output (fixed current output) Used for loop checks.
setup Output can be set freely from –5% to 110% in 1% steps.
P. 8-17
User memo fields Allows user to enter up to 5 items of any desired text in up to 8 uppercase alphanumeric
P. 8-17 characters per item.
IM 01C21C01-01E
8.3.3 Setting Parameters SET Set TAG NO. and press the
C10:TAG NO.
Set or change the parameters as necessary. After YOKOGAWA key.
FIC-1a _
completing these, do not fail to use the “DIAG” key
to confirm that “GOOD” is displayed for the self- CODE caps CLE ESC
diagnostic result at _60: SELF CHECK.

When you have made an entry mistake, return
the cursor using the key, then reenter.
(1) Tag No. Setup
(C10: TAG NO) SET This is the panel for confirming
C10:TAG NO.
YOKOGAWA set data. The set data items flash.
Use the procedure below to change the Tag No. Up FIC-1a
When all items have been
to 16 alphanumeric characters can be entered. PRINTER OFF
F2:PRINTER ON
FEED POFF NO
confirmed, press the
again. (To go back to the setting
• Example: Set a Tag No. to FIC-1a panel, press the (NO) key.
Press the key to turn on SET The DPharp TAG NO. was
the BT200. C10:TAG NO.
FIC-1a overwritten.
<When power is off>
Press the (OK) key to
FEED NO OK
return to the parameter panel.
--WELCOME-- Connect DPharp and BT200 Press the (NO) key to
BRAIN TERMINAL PARAM
ID: BT200 using a communication cable and C10:TAG NO.
FIC-1a
return to the setting panel.
check connection press the key. C20:PRESS UNIT
kPa
push ENTER key
C21:LOW RANGE
0 kPa
UTIL FEED
DATA DIAG PRNT ESC
PARAM Displays the name of connected
01:MODEL F0812-2.ai
EJA110A-DM DPharp model, TAG NO. and
02:TAG NO.
YOKOGAWA diagnostics information. Press the
03:SELF CHECK
GOOD (OK) key after confirmation. (2) Calibration Range Setup
OK
a. Setting Calibration Range Unit
MENU Press the (SET) key to
A:DISPLAY
B:SENSOR TYPE display the SET menu panel. (C20: PRESS UNIT)
The unit is set at the factory before shipment if
HOME SET ADJ ESC specified at the time of order. Follow the procedure
MENU Select C: SETTING and press the below to change the unit.
C:SETTING
D:AUX SET 1 key.
E:AUX SET 2
H:AUTO SET
• Example: Change the unit from mmH2O to
HOME SET ADJ ESC kPa.
MENU Select C10: TAG NO. and press SET Use the or
C10:TAG NO. C20:PRESS UNIT
YOKOGAWA the key. mmH20
C20:PRESS UNIT < mmWG > key to select “kPa.”
kPa < mmHG >
C21:LOW RANGE < Torr > Press the key twice
0 kPa < kPa >
DATA DIAG PRNT ESC ESC to enter the setting.
SET Set the new TAG NO. (FIC-1a). SET
C10:TAG NO. Press the (OK) key.
YOKOGAWA FOKOGAWA C20:PRESS UNIT
kPa
YOKOGAWA
FIKOGAWA
CODE CAPS CLR ESC FICOGAWA
FEED NO OK
FIC-GAWA
FIC-1AWA mmH2O
mmAq
FIC-1aWA mmWG
FIC-1a mmHg
Torr
F0812-1.ai kPa
MPa
mbar
bar
gf/cm2
kgf/cm2
inH2O
inHg
ftH2O
psi
atm
F0813.ai
IM 01C21C01-01E
b. Setting Calibration Range Lower Range
Value and Higher Range Value • Example 2: With present settings of 0 to
(C21: LOW RANGE, C22: HIGH RANGE) 30 kPa, set the Higher range
value to10 kPa.
These range values are set as specified in the
order before the instrument is shipped. Follow the
SET
C22:HIGH RANGE
Set 10.
30 kPa Press the key twice
procedure below to change the range. + 10
to enter the setting.
• The measurement span is determined by DEL CLR ESC
the high and low range limit values. In this
SET Press the (OK) key.
instrument, changing the low range value also C22:HIGH RANGE
10 kPa
automatically changes the high range value,
keeping the span constant.
FEED NO OK
• Example 1: With present settings of 0 to PARAM

C20:PRESS UNIT
The low range value is not
30 kPa, set the lower range value kPa changed, so the span changes.
C21:LOW RANGE
0 kPa
to 0.5 kPa. C22:HIGH RANGE
10 kPa
DATA DIAG PRNT ESC
SET
C21:LOW RANGE
Set 0.5.
0 kPa Press the key twice to F0815.ai
+ 0.5
enter the setting.
(3) Damping Time Constant Setup
DEL CLR ESC
(C30: AMP DAMPING)
SET
Press the (OK) key.
C21:LOW RANGE
0.5 kPa When the instrument is shipped, the damping time
constant is set at 2.0 seconds. Follow the procedure
below to change the time constant.
FEED NO OK
SET
C20:PRESS UNIT
The higher range value is • Example: Change from 2.0 sec to 4.0 sec.
kPa
C21:LOW RANGE changed while the span remains
SET
0.5 kPa
constant. C30:AMP DAMPING Use the or
C22:HIGH RANGE
2.0 sec
30.5 kPa
DATA DIAG PRNT ESC < 2.0 sec > key to select 4.0 sec.
< 4.0 sec >
< 8.0 sec > Press the key twice
(Span = Higher range value – Lower range value ) < 16.0 sec >
ESC to enter the setting.
F0814.ai
SET
C30:AMP DAMPING Press the (OK) key.
• Note, however, that changing the higher range 4.0 sec
value does not cause the lower range value to

change. Thus, changing the higher range value FEED NO OK
also changes the span.
0.2sec
• Calibration range can be specified with range 0.5sec
value specifications up to 5 digits (excluding 1.0sec
2.0sec
any decimal point) for low or high range limits
within the range of −32000 to 32000. 4.0sec
8.0sec
16.0sec
32.0sec
64.0sec
F0816.ai
Note: The damping time constant set here is the damping time
constant for the amplifier assembly. The damping time
constant for the entire transmitter is the sum of the values
for the amplifier assembly and for the capsule assembly.
For the capsule assembly damping time constant (fixed),
see the “General Specifications” found at the end of this
manual. (See Chapter 10.)
IM 01C21C01-01E
(4) Output Signal Low Cut Mode Setup (5) Change Output Limits
(D10: LOW CUT, D11: LOW CUT MODE) (D15: OUT LIMIT(L), D16: OUT LIMIT(H))
Low cut mode can be used to stabilize the output The range of normal output is preset at the factory
signal near the zero point. The low cut point can be from −5.0% to 110.0% unless otherwise specified,
set in a range from 0 to 20% of output. (Hysteresis: and the output is limited with these upper and lower
±1%) values. This output range can be changed, for
example, to meet the requirements of NAMUR, etc.
Either “ZERO” as the low cut mode.
within the settable range. Set the lower limit with
 Low cut mode “ZERO” D15: OUT LIMIT(L) and upper limit with D16: OUT
(%) LIMIT(H).
50
Settable range: −5.0 to 110.0 (%)
Output
Lower limit < Upper limit
20
(6) Integral Indicator Scale Setup
The following 5 displays are available for integral
0 50 (%)
Input indicators.
F0817.ai
D20: DISP SELECT Description

● Example: Change the low cut setting range and Display and Related parameters
from 10% to 20%, and the low NORMAL % Indicates –5 to 110% range
depending on the Measurement
cut mode from LINEAR to ZERO.
range (C21, C22).
SET Set “20.” A10:OUTPUT (%)
D10:LOW CUT
10.0 %
Press the key twice to 45.6 %
+ 20.0
enter the setting. USER SET Indicates values depending on the

CLR ESC Engineering range (D22, D23).(Note 1)
Units set using Engineering unit
SET Press the (OK) key. (D21) are not indicated.
D10:LOW CUT
20.0 %
Next, the [D11: LOW CUT MODE] A11:ENGR.OUTPUT
setting panel is displayed. 20.0 M
FEED NO OK
USER & % Indicates user set and % alternately
in 3 second intervals.
SET Use the or key
D11:LOW CUT MODE
LINEAR A10:OUTPUT (%)
< LINEAR > to select “ZERO.”
< ZERO > 45.6 %
Press the key twice to A11:ENGR. OUTPUT
ESC
enter the setting. 20.0 M
SET
D11:LOW CUT MODE
Press the (OK) key. INP PRES Indicates input pressure.(Note 2)
ZERO Indication limits –19999 to 19999.
A40:INPUT
FEED NO OK 456 kPa
PARAM
PRES & % Indicates input pressure and %
D10:LOW CUT alternately in 3 second intervals.
20.0 %
D11:LOW CUT MODE
ZERO A10:OUTPUT (%)
D20:DISP SELECT
NORMAL % 45.6 %
DATA DIAG PRNT ESC
A40:INPUT
456 kPa
F0818.ai
F0819.ai
Note 1: Scale range can be specified with range limit

specifications up to 5 digits (excluding any decimal
point) for low or high range limits within the range of
–19999 to 19999.
The range with decimals is available to the third
decimal place.
Note 2: It indicates the value after zeroing.
See (a.) through (c.) for each setting procedure.
IM 01C21C01-01E
b. Setting User-set Engineering Unit
% indication and User-set engineering
(D21: DISP UNIT)
input pressure unit display
indication This parameter allows entry of the engineering units
to be displayed on the BT200. When the instrument
D20: DISP SELECT D20: DISP SELECT is shipped, this is set as specified in the order.
NORMAL % USER SET
INP PRES USER & % Follow the procedure below to change this setting.
PRES & %
This parameter need not be set for % display.
Set for user-set
Transmitter is set engineering unit display.
• Example: Set an engineering unit M.
for “% display” when
shipped. SET Set “M.”
D21:DISP UNIT
D21: DISP UNIT
M_ Press the key twice to
Set a unit to be
enter the setting.
displayed on the BT200.
CODE CAPS CLR ESC

D21:DISP UNIT
D22: DISP LRV M
Set a numeric value for

engineering unit for 4 mA
FEED NO OK
output (LRV).
F0822.ai
D23: DISP HRV

Set a numeric value for
engineering unit for 20 mA
output (HRV).
F0820.ai
a. Display Selection (D20: DISP SELECT)

Follow the instructions given to the below to change
the range of integral indication scales.
When USER SET is selected, the user set values
of integral indication and A11: ENGR. OUTPUT
parameter are indicated.
• Example: Set the integral indicator scale to

engineering units display.
SET Use the or key
D20:DISP SELECT
NORMAL %
<NORMAL %> to select “USER SET.”
<USER SET>
<USER & %> Press the key twice to
<INP PRES>
ESC enter the setting.
SET
D20:DISP SELECT Press the (OK) key.
USER SET
FEED NO OK
The “%” disappears from the

integral indicator display.
F0821.ai
IM 01C21C01-01E
c. Lower and Higher Range Value Setup in (8) Unit Setup for Displayed Static Pressure
Engineering Unit (D31: STAT.P.UNIT)
(D22: DISP LRV, D23: DISP HRV)
Follow the procedure below to change the static
These parameter items are used to set the lower pressure units.
and higher range values for the engineering unit
Changing this parameter changes the unit for the
display.
A30: STATIC PRESS (static pressure) display.
When the instrument is shipped, these are set
as specified in the order. Follow the procedure • Example: Change the static pressure unit
below to change these settings. Note that these from kgf/cm2 to MPa.
parameters need not be set for % display. SET Use the or key
D31:STAT.P.UNIT
kgf/cm^2
< MPa > to select MPa.
• Example: Set lower range value (LRV) to –50 < mbar >
< bar > Press the key twice
and higher range value (HRV) to 50. < gf/cm^2 >
ESC
to enter the setting.
Setting LRV mmH2O
mmAq
SET Set “–50.” mmWG
D22:DISP LRV
0M mmHg
- 50 Press the key twice to Torr
kPa
enter the setting. MPa
DEL CLR ESC mbar
bar
gf/cm2
Setting HRV kgf/cm2
SET Set “50.” inH2O
D23:DISP HRV
100M inHg
+ 50 Press the key twice to ftH2O
psi
enter the setting. atm
DEL CLR ESC
F0825.ai
SET Press the (OK) key. (9) Operation Mode Setup

D23:DISP HRV
50M (D40: REV OUTPUT)
This parameter allows the direction of the 4 to 20
FEED NO OK
mA output to be reversed with respect to input.
PARAM Follow the procedure below to make this change.
D21:DISP UNT
M
D22:DISP LRV
-
D23:DISP
50M
HRV
• Example: Change 4 to 20 mA output to 20 to
DATA
50M
DIAG PRNT ESC 4 mA output.
F0823.ai
SET Use the or key
D40:REV OUTPUT
NORMAL
< NORMAL > to select REVERSE.
< REVERSE>
(7) Unit Setup for Displayed Temperature Press the key twice to
(D30: TEMP UNIT) ESC
enter the setting.
When the instrument is shipped, the temperature F0826.ai
units are set to degC. Follow the procedure below

to change this setting. Note that changing the
unit here changes the unit for A20: AMP TEMP
(amplifier temperature) and A21: CAPSULE TEMP
(capsule temperature).
• Example: Change the unit for the temperature

display.
SET
D30:TEMP UNIT
Use the or key
deg C
< deg C > to select “deg F.”
< deg F >
Press the key twice to
ESC
enter the setting.
F0824.ai
IM 01C21C01-01E
(10) Output Status Display/Setup when a CPU (12) Range Change while Applying Actual
Failure Inputs
(D52: BURN OUT) (H10: AUTO LRV, H11: AUTO HRV)
This parameter displays the status of 4 to 20 mA This feature allows the lower and higher range
DC output if a CPU failure occurs. In case of a values to be set up automatically with the actual
failure, communication is disabled. input applied. If the lower and higher range values
are set, C21: LOW RANGE and C22: HIGH
Setting of HIGH or LOW is enabled. This is done
RANGE are changed at this same time.
with the pin (CN4) on the CPU assembly. See
Chapter 3 for details. Follow the procedure in the figure below.
The measurement span is determined by the higher
Standard specifications
and lower range values. Changing the lower range
The parameter is set to HIGH. If a failure, the value results in the higher range value changing
transmitter outputs the signal of 110% or higher. auto-matically, keeping the span constant.
The parameter D53: ERROR OUT is set to HIGH
from the factory. • Example 1: When changing the lower range
value to 0.5 kPa for the present
Optional code/C1
setting of 0 to 30 kPa, take the
The parameter is set to LOW. If a failure, output following action with input pressure
which is −5% or lower is generated. The parameter of 0.5 kPa applied.
D53: ERROR OUT is set to LOW from the factory.
SET Press the key twice.
H10:AUTO LRV
0 kPa
• Example: Standard specifications + 0 The lower range value is
pin (CN4) position: H changed to 0.5 kPa.

D52: BURN OUT
HIGH ESC

H10:AUTO LRV
• Example: Optional code/C1 0.5000 kPa
D52: BURN OUT pin (CN4) position: L

LOW
FEED NO OK
F0827.ai PARAM
H10:AUTO LRV
The higher range value is
0.5000 kPa
H11:AUTO HRV changed keeping the span
(11) Output Status Setup when a Hardware 30.500 kPa
H60:SELF CHEC constant.
Error Occurs GOOD
DATA DIAG PRNT ESC
Parameters C21 and C22 are
(D53: ERROR OUT)
changed at the same time.
This parameter allows the setting of the output F0829.ai
status when a hardware error occurs. The following

Note that changing the higher range value does not
three selections are available.
cause the lower range value to change but does
(a) HOLD; Outputs the last value held before the change the span.
error occurred.
(b) HIGH; Outputs an output of 110% when an
error has occurred.
(c) LOW; Outputs an output of −5% when an error
has occurred.
Note: A hardware error means CAP MODULE FAULT of Er.01
or AMP MODULE FAULT of Er. 02 which are shown in
8.5.2 “Errors and Countermeasures.”)
• Example: Set the output status to LOW when

a hardware error occurs.
SET
D53:ERROR OUT Use the or key
HIGH
< HIGH> to select “LOW.”
< LOW>
< HOLD>
ESC
enter the setting.
F0828.ai
IM 01C21C01-01E
(a) Follow the procedure below when setting the
• Example 2: When the higher range value is to
present output to 0% (4 mA).
be changed to 10 kPa with the
present setting of 0 to 30 kPa, take Output is 0.5%.
A10:OUTPUT (%)
the following action with an input 0.5 %
pressure of 10 kPa applied.

SET
J10:ZERO ADJ Press the key twice.
SET Press the key twice.
H11:AUTO HRV 0.0 %
30 kPa + 000.0
+ 30 The higher range value is
changed to 10 kPa. CLR ESC
ESC
SET
Zero adjustment is completed.
SET
H11:AUTO HRV
Press the (OK) key. J10:ZERO ADJ
0.0 %
10.000 kPa Press the (OK) key.
FEED NO OK
FEED NO OK
PARAM The lower range value is not A10:OUTPUT (%) Output is 0%.
H10:AUTO LRV 0.0 %
0 kPa
H11:AUTO HRV changed, so the span changes.
10.000 kPa
H60:SELF CHECK Parameter C22 is changed at the F0831.ai
GOOD
DATA DIAG PRNT ESC
same time. (b) In tank level measurement, if the actual level
F0830.ai cannot be brought to zero for zero adjustment,
then the output can be adjusted to correspond
(13) Zero Point Adjustment to the actual level obtained using another
(J10: ZERO ADJ, J11: ZERO DEV, J20: EXT measuring instrument such as a glass gauge.
ZERO ADJ)
Present level: 45%
The DPharp supports several adjustment methods. Present output: 41%
Select the method best suited for the conditions of 100%

your application.
Note that output signal can be checked by
displaying parameter A10:OUTPUT (%) on the Present level
45%
BT200.
Adjustment
Description 0%
Method
Using the Set the present input to 0%. F0832.ai
BT200 Adjust for 0% output at input level of
0%. (b)-1 Follow the procedure below to use J10:
Adjust output to the reference value ZERO ADJ.
obtained using other means.
If the input level cannot easily be A10:OUTPUT (%)
Present output is 41.0%.
made 0% (because of tank level, etc.), 41.0 %
adjust output to the reference value

obtained using other means, such as SET Enter the present actual level,
a sight glass. J10:ZERO ADJ
0.0 %
Using the Adjust zero point using the zero- + 045.0 45%.
external adjustment screw on the transmitter. Press the key twice.
zero- This permits zero adjustment without CLR ESC
adjustment using the BT200. Accurately adjust the
screw output current to 4 mA DC or other target A10:OUTPUT (%) The output is changed to 45%.
output value using an ammeter that 45.0 %
accuratly reads output currents.

F0833.ai
IM 01C21C01-01E
(b)-2 Follow the procedure below to use J11: • Zero point adjustment using external zero-
ZERO DEV. adjustment screw on the transmitter
A10:OUTPUT (%)
Present output is 41.0%. Turn the zero-adjustment screw on the outside of
41.0 %
Output error = 45.0 – 41.0 = 4.0%. the transmitter case using a slotted screwdriver.
Turn the screw to the right to increase the zero point
SET Since “J11: ZERO DEV.” contains
J11:ZERO DEV.
2.50 %
or to the left to decrease the zero output; the zero
0 the previous correction, obtain the adjusts in increments of 0.01% of the range setting.
correction value by adding 4.0% Note that the amount of adjustment to the zero point
ESC
to it. (2.50% + 4.0% = 6.50%) changes according to the speed at which the screw
is turned. To make fine adjustments, turn the screw
SET Set the correction value, 6.50.
J11:ZERO DEV.
2.50 % slowly; to make coarse adjustments, turn the screw
6.50 Press the key twice.
quickly.
ECS Note: When a zero point adjustment has been made, do not turn
off the transmitter less than 30 seconds after adjustment.
A10:OUTPUT (%) The output is changed to 45%.
45.0 % (14) Span Adjustment
F0834.ai Each DPharp EJA series transmitter is factory
When the zero point is adjusted, the displayed characterized according to the specification.
value of A40 is as follows. Mounting position effects or zero shifts caused by
static pressure are typically compensated by a zero
[Example] adjustment.
When the zero point is shifted by 20 kPa for the A span adjustment is a function to correct the slope
actual pressure, the parameter of A40 indicates 50 error from a zero point in characterizing 100% point
kPa. (HRV). This function can be used when span drifts
may be caused or characterization to the specific
pressure standard is required.
70 kPa
Therefore, the zero point adjustment should always
50 kPa
be performed before the upper point adjustment in
order to maintain the pitch between zero and 100%
Zero
20 kPa adjustment points within the calibration range.
Zero adjustment
volume(J11)
0 kPa 0 kPa You can manually perform the trimming procedure
Actual differential Input value
pressure/pressure of A40
by using J15: SPAN ADJ.
F0835.ai
• Span adjustment value
(c) Zero Point Adjustment Using the External Zero The span adjustment value is calculated as
Adjustment Screw follows.
• Enabling/inhibiting of zero point adjustment
P – A40 ×100
using the external zero-adjustment screw on Span adjustment value (%) = 1
P1
the transmitter (J20: EXT ZERO ADJ)
P1: Actual differential pressure/pressure value
Follow the procedure below to enable or inhibit zero A40: Input (indicated as the value after zeroing)
point adjustment from the zero-adjustment screw
Measurement pressure
on the transmitter.
This is set to “ENABLE” when the instrument is
shipped. A40
• Example: Inhibiting zero adjustment by the

Applied pressure
external zero-adjustment screw P1
0
F0837.ai
SET
J20:EXIT ZERO ADJ
Use the or key
ENABLE
< ENABLE > to select “INHIBIT.”
< INHIBIT>
ESC
enter the setting.
F0836.ai
IM 01C21C01-01E
• Example: For the range of 0 to 30 kPa. IMPORTANT

A40: INPUT = 30.15 kPa
J15: SPAN ADJ = 0.15 % 1. Test output is held for approximately 10
minutes, and then released automatically
Suppose that a standard pressure of 30 kPa is applied after the time has elapsed. Even if the
and the value of the parameter of A40:INPUT is 30.15 kPa.
Firstly, obtain the slope error for the span as follows; BT200 power supply is turned off or the
communication cable is disconnected during
P1 – A40
Span adjustment value (%) = ×100 test output, it is held for approximately 10
P1
minutes.
30.00 – 30.15
= ×100 = −0.5 (%) 2. Press the [F4] (OK) key to release test output
30.00
immediately.
Add −0.5% to 0.15% of the current value to calculate the
accumulated span adjustment value.
(16) User Memo Fields
0.15 + (−0.50) = –0.35 (M: MEMO)
SET Set −0.35.

This feature provides 5 user memo fields, each
J15:SPAN ADJ
0.15 % holding up to 8 alphanumeric characters. Up to 5
- 0.35 Press key twice.
items such as inspection date, inspector, and other
DEL CLR ESC
information can be saved in these fields.
J15:SPAN ADJ
-0.35 % • Example: Save an inspection date of January
30, 1995.
FEED NO OK PARAM
M10:MEMO 1
Set “95.1.30” in the order of year,
month, and day.
Note: Enter 0.00 to J15: SPAN ADJ to reset the M20:MEMO 2
span adjustment to the initial value at the

M30:MEMO 3 Press the key twice to
DATA DIAG PRNT ESC
shipment. enter the setting.
SET
M10:MEMO 1
F0838.ai
95.1.30_
(15) Test Output Setup

ESC
(K10: OUTPUT X%)
This feature can be used to output a fixed current F0840.ai
from 3.2 mA (−5%) to 21.6 mA (110%) for loop

checks.
• Example: Output 12 mA (50%) fixed current.

SET
K10:OUTPUT X %
Set “50.0%.”
0.0 %
+ 050.0 Press the key twice to
output a fixed current at 50%.
ESC
SET “Active” is displayed while this is

K10:OUTPUT X %
50.0 % ACTIVE
being executed.
Press the (OK) key to cancel
FEED NO OK
the fixed current output.
F0839.ai
IM 01C21C01-01E
8.4 Displaying Data Using the 8.5 Self-Diagnostics
BT200 8.5.1 Checking for Problems
8.4.1 Displaying Measured Data
(1) Identifying Problems with BT200
The BT200 can be used to display measured data.
The following four areas can be checked.
The measured data is updated automatically every
(a) Whether connections are good.
7 seconds. In addition, the display can be updated
(b) Whether BT200 was properly operated.
to the present data value at any time by pressing
(c) Whether settings were properly entered.
the [F1] (DATA) key. For parameters associated
(d) History of the errors.
with the display of measured data, see Subsection
See examples below.
8.3.1, “Parameter Summary.”
• Example 1: Connection errors
• Example: Display output.
--WELCOME--
BRAIN TERMINAL
Press the key.
MENU
A:DISPLAY ID: BT200
B:SENSOR TYPE
When the panel shown on the left
check connection
push ENTER key appears, press the key.
UTIL FEED
HOME SET ADJ ESC
Since communications will be
PARAM
A10:OUTPUT (%)
Display “A10: OUTPUT (%).”
XX.X % communication error unsuccessful if there is a problem
A11:ENGR.OUTPUT
YY.Y % in the connection to the BT200,
A20:AMP TEMP
ZZ deg C ESC the display at the left will appear.
DATA DIAG PRNT ESC
Data is updated automatically
Recheck the connection.
PARAM communi
at 7-second intervals.
A10:OUTPUT (%) Press the (OK) key.
A11:ENGR.OUTPUT
F0843.ai
A20:AMP TEMP
F0841.ai • Example 2: Setting entry errors

PARAM The initial data panel shows the
8.4.2 Display Transmitter Model and 01:MODEL
EJA210A-DM
result of current transmitter
Specifications 02:TAG NO.
YOKOGAWA
03:SELF CHECK diagnostics.
ERROR
The BT200 can be used to display the model and OK
specifications of the transmitter. PARAM

C20:PRESS UNIT
Press the (DIAG) key in the
kPa
parameter panel to go to the
• Example: View transmitter model name. C21:LOW RANGE
600 kPa
C22:HIGH RANGE
600 kPa
diagnostics panel
MENU Press . DATA DIAG PRNT ESC
A:DISPLAY (C60: SELF CHECK).
B:SENSOR TYPE
DIAG An error message is displayed
C60:SELF CHECK
ERROR
< ERROR > when an error occurs in the
< ILLEGAL LRV >
HOME SET ADJ ESC diagnostics panel.
FEED PRNT ESC
F0844.ai
PARAM
B10:MODEL For the associated
EJA210A-DM parameters, see
B11:STYLE NO.
S1.01 Subsection 8.3.1,
B20:LRL Parameter Summary.
- 98.07 kPa
DATA DIAG PRNT ESC
F0842.ai
IM 01C21C01-01E
(2) Checking with Integral Indicator
• Example 3: Checking the history of the errors
MENU
J:ADJUST
Connect the BT200 to the NOTE
K:TEST
M:MEMO
transmitter, and call item “P.”
P:RECORD If an error is detected in the self-diagnostic,
HOME SET ADJ ESC
an error number is displayed on the integral
indicator. If there is more than one error, the error
PARAM
P10:ERROR REC 1 number changes at two-second intervals. See
ERROR
P11:ERROR REC 2
ERROR
Table 8.2 regarding the error numbers.
P12:ERROR REC 3
GOOD
DATA DIAG PRNT ESC
P10: “ERROR REC 1” displays the last error.

P11: “ERROR REC 2” displays the error one time before
the last error occurred.
P12: “ERROR REC 3” displays the error two times before
the last error occurred.
P13: “ERROR REC 4” displays the error three times
before the last error occurred.
The history of up to four errors can be stored. When the

F0846.ai
5th error has occurred, it is stored in “P10”. The error
stored in “P13” will be deleted, and then, the error in “P12”
Figure 8.5 Identifying Problems Using the Integral
will be copied to “P13”. In this sequence, the history of the
Indicator
most previously occurred error will be removed from
memory.
“GOOD” will be displayed if there was no previous error.
SET Select P10: ERROR REC1 and

P10:ERROR REC 1
<
ERROR
ERROR >
press the key to
< ILLEGAL LRV > display the error message.
< ILLEGAL HRV >
ESC
<(a) SETUP PANEL>
For the details of the messages listed below, see Table

8.5.1 Error Message Summary.
CAP MODULE FAULT OVER TEMP (CAP) ILLEGAL LRV

AMP MODULE FAULT OVER TEMP (AMP) ILLEGAL HRV
OUT OF RANGE OVER OUTPUT ILLEGAL SPAN
OUT OF SP RANGE OVER DISPLAY ZERO ADJ OVER
Note 1: Press the key twice in the setting panel

(panel 1) to clear all error message (P10 to P13)
information.
Note 2: After two hours from when an error occurs, the
error message of that error will be recorded.
Therefore, if you switch off the transmitter within
two hours from when the error occurs, there is no
history of that error stored in the transmitter, and
this function is meaningless.
F0845.ai
IM 01C21C01-01E
8.5.2 Errors and Countermeasures
The table below shows a summary of error messages.
Table 8.2 Error Message Summary
Integral
Output Operation during
Indicator BT200 Display Cause Countermeasure
Error
Display
None GOOD
--- ERROR
Er.01 CAP MODULE FAULT Capsule problem.*1 Outputs the signal (Hold, Replace the capsule when
High, or Low) set with error keeps appearing even
parameter D53. after restart.*2
Er.02 AMP MODULE FAULT Amplifier problem. Outputs the signal (Hold, Replace amplifier.
High, or Low) set with
parameter D53.
Er.03 OUT OF RANGE Input is outside Outputs high range limit Check input.
measurement range value or low range limit
limit of capsule. value.
Er.04 OUT OF SP RANGE Static pressure exceeds Displays present output. Check line pressure (static
specified range.*3 pressure).
Er.05 OVER TEMP (CAP) Capsule temperature is Displays present output. Use heat insulation or make
outside range lagging to keep temperature
(–50 to 130°C). within range.
Er.06 OVER TEMP (AMP) Amplifier temperature is Displays present output. Use heat insulation or make
outside range lagging to keep temperature
(–50 to 95°C). within range.
Er.07 OVER OUTPUT Output is outside high or Outputs high or low range Check input and range
low range limit value. limit value. setting, and change them as
needed.
Er.08 OVER DISPLAY Displayed value is Displays high or low range Check input and display
outside high or low limit value. conditions and modify them
range limit value. as needed.
Er.09 ILLEGAL LRV LRV is outside setting Holds output immediately Check LRV and modify as
range. before error occurrence. needed.
Er.10 ILLEGAL HRV HRV is outside setting Holds output immediately Check HRV and modify as
Er.11 ILLEGAL SPAN SPAN is outside setting Holds output immediately Check SPAN and change as
Er.12 ZERO ADJ OVER Zero adjustment is too Displays present output. Readjust zero point
large.
*1: This error code appears at a capsule problem or when an illegal overpressure is applied to the pressure sensor.
*2: If the normal pressure is regained, the Er.01 will disappear according to the setting of the parameter of E50: AUTO RECOVER.
When the E50: AUTO RECOVER is set to ON(defalut setting), the Er.01 will disappear automatically. When the E50: AUTO
RECOVER is set to OFF, restart the transmitter to cancel Er.01. If no error code appears then, perform necessary adjustment such
as zero-adjustment to continue the operation. If the error code still exists, replace the capsule assembly.
*3: For Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
IM 01C21C01-01E
<9. Maintenance> 9-1
9. Maintenance
9.1 Overview 9.2 Calibration Instruments
Selection
WARNING Table 9.1 shows the instruments required for
Since the accumulated process fluid may be calibration. Select instruments that will enable
toxic or otherwise harmful, take appropriate care the transmitter to be calibrated or adjusted to the
to avoid contact with the body, or inhalation of required accuracy.
vapors during draining condensate or venting The calibration instruments should be handled
gas in transmitter pressure-detector section and carefully so as to maintain the specified accuracy.
even after dismounting the instrument from the
process line for maintenance.
9.3 Calibration
Maintenance of the transmitter is easy due to its Use the procedure below to check instrument
modular construction. This chapter describes the operation and accuracy during periodic
procedures for calibration, adjustment, and the maintenance or troubleshooting.
disassembly and reassembly procedures required
1) Connect the instruments as shown in Figure 9.1
for component replacement.
and warm up the instruments for at least five
Since the transmitters are precision instruments, minutes.
carefully and thoroughly read the following sections
for proper handling during maintenance.
IMPORTANT
• To adjust the transmitter for highest
IMPORTANT accuracy, make adjustments with the
power supply voltage and load resistance
• As a rule, maintenance of this transmitter
including leadwire resistances set close to
should be implemented in a maintenance
the conditions under which the transmitter is
service shop where the necessary tools are
installed.
provided.
• If the measurement range 0% point is
• The CPU assembly contains sensitive parts
0 kPa or shifted in the positive direction
that may be damaged by static electricity.
(suppressed zero), the reference pressure
Exercise care so as not to directly touch
should be applied as shown in the figure
the electronic parts or circuit patterns on
(low pressure side open to atmosphere). If
the board, for example, by preventing static
the measurement range 0% point is shifted
electrification by using grounded wrist straps
in the negative direction (elevated zero), the
when handling the assembly. Also take
reference pressure should be applied on the
precautions such as placing a removed
low pressure side (high pressure side open
CPU assembly into a bag with an antistatic
to atmosphere).
coating.
• Do not perform the calibration procedures
until the transmitter is at room temperature.
2) Apply reference pressures of 0%, 50%,

and 100% of the measurement range to the
transmitter. Calculate the errors (differences
between digital voltmeter readings and
reference pressures) as the pressure is
increased from 0% to 100% and is decreased
from 100% to 0%, and confirm that the errors
are within the required accuracy.
IM 01C21C01-01E
Table 9.1 Instruments Required for Calibration
Name Yokogawa-recommended Instrument Remarks
Power supply Model SDBT or SDBS distributor 4 to 20 mA DC signal
Load resistor Model 2792 standard resistor [250 Ω ±0.005%, 3 W]
Load adjustment resistor [100 Ω ±1%, 1 W]
Voltmeter Model 2501 A digital multimeter
Accuracy (10V DC range): ±(0.002% of rdg + 1 dgt)
Digital Model MT220 precision digital manometer Select a manometer having a
manometer 1) For 10 kPa class pressure range close to that of
Accuracy: ± (0.015% of rdg + 0.015% of F.S.) · · for 0 to 10 kPa the transmitter.
± (0.2% of rdg + 0.1% of F.S.) · · · · · · for −10 to 0 kPa
2) For 130 kPa class
Accuracy: ± 0.02% of rdg · · · · · · · · · · · · · · · · · · for 25 to 130 kPa
± 5 digits · · · · · · · · · · · · · · · · · · · · · · · for 0 to 25 kPa
Accuracy: ± (0.02% of rdg + 3 digits) · · · · · · · · · for 100 to 700 kPa
± 5 digits · · · · · · · · · · · · · · · · · · · · · · · for 0 to 100 kPa
Accuracy: ± (0.02% of rdg + 10 digits) · · · · · · · · for 0 to 3000 kPa
5) For 130 kPa abs class
Accuracy: ± (0.03% of rdg + 6 digits) · · · · · · · · · for 0 to 130 kPa abs
Pressure Model 7674 pneumatic pressure standard for 200 kPa {2 kgf/cm2}, Requires air pressure supply.
generator 25 kPa {2500 mmH2O}
Accuracy: ± 0.05% of F.S.
Dead weight gauge tester 25 kPa {2500 mmH2O} Select the one having a
Accuracy: ±0.03% of setting pressure range close to that of
the transmitter.
Pressure Model 6919 pressure regulator (pressure pump) Prepare the vacuum pump for
source Pressure range: 0 to 133 kPa {1000 mmHg} negative pressure ranges.
Note: The above table contains the instruments capable of performing calibration to the 0.2% level. Since special maintenance and
management procedures involving traceability of each instrument to higher-level standards are required for calibration to the 0.1%
level, there are difficulties in calibration to this level in the field. For calibration to the 0.1% level, contact Yokogawa representatives
from which the instrument was purchased or the nearest Yokogawa office.
Terminal box
Power
Load resistance, 250Ω supply
E
Rc R (Note) For Model EJA220A transmitter
Load adjusting (diaphragm-extended type), prepare a
resistance, 100Ω V mating calibration flange to match
the diaphragm extension length and
Digital voltmeter outer diameter.
Model MT220
Model 7674 precision Mating (Note)
pneumatic digital manometer calibration
pressure standards flange
Supply pressure P P
Pressure source
Reference pressure
F0901.ai
Figure 9.1 Instrument Connections
IM 01C21C01-01E
9.4 Disassembly and
Reassembly
This section describes procedures for disassembly
and reassembly for maintenance and component Shrouding Bolt
replacement.
Shrouding Bolt
Always turn OFF power and shut off and release
pressures before disassembly. Use proper tools for F0902.ai
all operations. Table 9.2 shows the tools required. Figure 9.2 Shrouding Bolts
Table 9.2 Tools for Disassembly and Reassembly
Tool Quantity Remarks 9.4.1 Replacing the Integral Indicator
Phillips 1 JIS B4633, No. 2
screwdriver
Slotted 1
CAUTION
screwdriver
Cautions for Flameproof Type Transmitters
Allen wrenches 2 JIS B4648
One each, nominal 3 and
Users are prohibited by law from modifying the
5 mm Allen wrenches construction of a flameproof type transmitter.
Wrench 1 Width across flats, 17 mm This would invalidate the agency approval and
Torque wrench 1 the transmitter’s use in such rated area.
Adjustable 1 Thus the user is prohibited from using a
wrench flameproof type transmitter with its integral
Socket wrench 1 Width across flats, 16 mm indicator removed, or from adding an integral
Socket driver 1 Width across flats, 5.5 mm
indicator to a transmitter. If such modification is
Tweezers 1
absolutely required, contact Yokogawa.
This subsection describes the procedure for

CAUTION replacing an integral indicator. (See Figure 9.4)
Precautions for CENELEC and IECEx
 Removing the Integral Indicator
Flameproof Type Transmitters
• Flameproof type transmitters must be, as 1) Remove the cover.
a rule, removed to a non-hazardous area 2) Supporting the integral indicator by hand,
for maintenance and be disassembled and loosen its two mounting screws.
reassembled to the original state. 3) Dismount the LCD board assembly from the
• On the flameproof type transmitters the two CPU assembly.
covers are locked, each by an Allen head When doing this, carefully pull the LCD board
bolt (shrouding bolt). When a shrouding bolt assembly straight forward so as not to damage
is driven clockwise by an Allen wrench, it is the connector pins between it and the CPU
going in and cover lock is released, and then assembly.
the cover can be opened.
When a cover is closed it should be locked by a
shrouding bolt without fail. Tighten the shrouding
bolt to a torque of 0.7 N·m.
IM 01C21C01-01E
 Attaching the Integral Indicator 3) Disconnect the output terminal cable (cable
Integral indicator can be installed in the following with brown connector at the end). When doing
three directions. this, lightly press the side of the CPU assembly
connector and pull the cable connector to
disengage.
4) Use a socket driver (width across flats, 5.5mm)
to loosen the two bosses.
5) Carefully pull the CPU assembly straight
forward to remove it.
F0903.ai
6) Disconnect the flat cable (cable with black
Figure 9.3 Installation Direction of Indicator connector at the end) that connects the CPU
assembly and the capsule.
1) Align both the LCD board assembly and CPU
assembly connectors and engage them. NOTE
2) Insert and tighten the two mounting screws.
Be careful not to apply excessive force to the
3) Replace the cover.
CPU assembly when removing it.
Output terminal cable
 Mounting the CPU Assembly
1) Connect the flat cable (with black connector)
Press between the CPU assembly and the capsule.
forward
2) Connect the output terminal cable (with brown
connector).
LCD board
assembly
Integral
NOTE
indicator
Make certain that the cables are free of pinching
Boss Zero-adjustment between the case and the CPU assembly edge.
Flat cable screw pin
Mounting CPU assembly 3) Align and engage the zero-adjustment screw
screw
Bracket
pin with the groove on the bracket on the CPU
Cover
(for zero-adjustment assembly. Then insert the CPU board assembly
screw pin)
F0904.ai straight onto the post in the amplifier case.
Figure 9.4 Removing and Attaching LCD Board 4) Tighten the two bosses. If the transmitter is
Assembly and CPU Assembly
equipped with an integral indicator, refer to
Subsection 9.4.1 to mount the indicator.
9.4.2 Replacing the CPU Board Assembly
This subsection describes the procedure for NOTE
replacing the CPU assembly. (See Figure 9.4) Confirm that the zero-adjustment screw pin is
placed properly in the groove on the bracket prior
 Removing the CPU Assembly
to tightening the two bosses. If it is not, the zero-
1) Remove the cover. If an integral indicator is adjustment mechanism will be damaged.
mounted, refer to Subsection 9.4.1 and remove
the indicator. 5) Replace the cover.
2) Turn the zero-adjustment screw to the position
(where the screw head slot is horizontal) as
shown in Figure 9.4.
IM 01C21C01-01E
9.4.3 Replacing the Process Connector 9.5.1 Basic Troubleshooting
Gaskets
First determine whether the process variable
This subsection describes the procedure for is actually abnormal or a problem exists in the
replacing the process connector gasket. (See measurement system.
Figure 9.5.)
If the problem is in the measurement system,
1) Loosen the two bolts and remove the process isolate the problem and decide what corrective
connector. action to take.
2) Replace the process connector gasket.
This transmitter is equipped with a self-diagnostic
3) Mount the process connector. Tighten the bolts
function which will be useful in troubleshooting; see
securely and uniformly to a torque of 39 to 49
Section 8.5 for information on using this function.
N·m{4 to 5 kgf·m}, and verify that there are no
pressure leaks. : Areas where self-diagnostic offers support
Abnormalities appear in measurement.
YES Is process variable

itself abnormal?
Process connector
gasket Inspect the NO
Measurement system problem
process system.
Bolt Isolate problem in

measurement system.
Process connector
YES Does problem exist in
F0905.ai
receiving instrument?
Figure 9.5 Replacing the Process Connector
Gasket
NO
Inspect receiver.
9.5 Troubleshooting
Environmental conditions Transmitter itself
If any abnormality appears in the measured values,
use the troubleshooting flow chart below to isolate
and remedy the problem. Since some problems Check/correct
Check transmitter.
environmental conditions.
have complex causes, these flow charts may
Operating conditions
not identify all. If you have difficulty isolating or
correcting a problem, contact Yokogawa service
personnel. Check/correct operating
conditions.
F0906.ai
Figure 9.6 Basic Flow and Self-Diagnostics
IM 01C21C01-01E
9.5.2 Troubleshooting Flow Charts Output travels beyond 0% or 100%.
The following sorts of symptoms indicate that transmitter

may not be operating properly.
Example : • There is no output signal. Connect BRAIN TERMINAL and check self-diagnostics.
• Output signal does not change even though
process variable is known to be varying.
• Output value is inconsistent with value
inferred for process variable.
Does the self- YES
diagnostic indicate problem
location?
Connect BRAIN TERMINAL and check self-diagnostics.
NO Refer to error message summary in
Subsection 8.5.2 to take actions.
Does the self-diagnostic YES

indicate problem location?
Is power supply NO
polarity correct?
YES Refer to Section 6.3 to check/correct
polarity at each terminal from power
supply to the terminal box.
Is power supply NO
polarity correct? NO
Are valves opened or
closed correctly?
YES
Refer to Section 6.3 to check/correct
polarity at each terminal from power
YES Fully open the low pressure valve.
supply to the terminal box.
Are power
NO
supply voltage and load
resistance correct? YES
Is there any pressure leak?
YES Refer to Section 6.6 for rated voltage

and load resistance. NO
Fix pressure leaks, paying particular
attention to connections for impulse
piping, pressure-detector section, etc.
Are valves opened or NO

closed correctly? Is zero point
adjusted correctly?
NO
YES Adjust the zero point.
YES Contact Yokogawa service personnel.

Is there any pressure leak?
F0908.ai
NO Fix pressure leaks, paying particular

attention to connections for impulse
piping, pressure-detector section, etc.
Is there
continuity through the NO
transmitter loop wiring?
Do the loop numbers
match?
Find/correct broken conductor or

YES
wiring error.
Contact Yokogawa service personnel.

F0907.ai
IM 01C21C01-01E
Large output error.
Connect BRAIN TERMINAL and check self-diagnostics.
Does the self- YES

diagnostic indicate problem
location?

Are valves opened or NO

closed correctly?
Is impulse piping NO
connected correctly?
YES Refer to individual model user manuals

and connect piping as appropriate for
the measurement purpose.
Are power supply NO

voltage and load resistance
correct?
YES Refer to Section 6.6 for rated voltage

and load resistance.
Is transmitter
installed where there is YES
marked variation in
temperature?
Provide lagging and/or cooling, or allow

NO adequate ventilation.
Were appropriate NO
instruments used for
calibration?
YES Refer to Section 9.2 when selecting

instruments for calibration.
NO
Is output adjusted correctly?
YES Adjust the output.
Contact Yokogawa service personnel.

F0909.ai
IM 01C21C01-01E
<10. General Specifications> 10-1
10. General Specifications

10.1 Standard Specifications Damping Time Constant (1st order):
The sum of the amplifier and capsule damping
Refer to IM 01C22T02-01E for FOUNDATION time constant must be used for the overall
Fieldbus communication type and IM 01C22T03- time constant. Amp damping time constant is
00E for PROFIBUS PA communication type marked adjustable from 0.2 to 64 seconds.
with “◊”.
EJA210A EJA220A
Capsule (Silicone Oil) M H M H
 Performance Specifications Time Constant (approx. sec) 0.4 0.4 0.4 0.4
See General Specifications sheet, GS 01C21C01-

Ambient Temperature Limits:
00E.
* Safety approval codes may affect limits.
 Functional Specifications –40 to 85°C (–40 to 185°F)
–30 to 80°C (–22 to 176°F) with LCD Display
Span & Range Limits Process Temperature Limits:
Measurement * Safety approval codes may affect limits.
inH2O mbar mmH2O
Span kPa –40 to 120°C (–40 to 248°F)
(/D1) (/D3) (/D4)
and Range
Span
10 to
1 to 100 4 to 400
100 to Working Pressure Limits (Silicone Oil)
1000 10000 2.7 kPa abs (0.38 psia) to flange rating
M
-100 to -400 to -1000 to -10000 to (see Figure 10.1)
Range
100 400 1000 10000
20 to 50 to 0.05 to 5
Span 5 to 500
2000 5000 kgf/cm2  Installation
H
-500 to -2000 to -5000 to -50 to 5
Range
500 2000 5000 kgf/cm2 Supply & Load Requirements “◊”:
* Safety approvals can affect electrical
URL is define as the Upper Range Limit from
requirements.
the table above.
See Section 6.6, ‘Power Supply Voltage and
Zero Adjustment Limits: Load Resistance.’
Zero can be fully elevated or suppressed,
Supply Voltage “◊”:
within the Lower and Upper Range Limits of the
10.5 to 42 V DC for general use and flameproof
capsule.
type
External Zero Adjustment “◊”: 10.5 to 32 V DC for lightning protector (Optional
External zero is continuously adjustable with code /A)
0.01% incremental resolution of span. Span 10.5 to 30 V DC for intrinsically safe, Type n,
may be adjusted locally using the digital nonincendive, or non-sparking type
indicator with range switch. Minimum voltage limited at 16.4 V DC for digital
Output “◊”: communications, BRAIN and HART
Two wire 4 to 20 mA DC output with digital EMC Conformity Standards:
communications, linear or square root EN 61326-1 Class A, Table 2 (For use in
programmable. BRAIN or HART FSK protocol industrial locations)
are superimposed on the 4 to 20 mA signal. EN 61326-2-3
Failure Alarm: EN 61326-2-5 (for Fieldbus)
Output status at CPU failure and hardware Immunity influence during the test
error; Differential pressure/pressure: Output shift is
Up-scale: specified within ±1% of 1/10 Max span.
110%, 21.6 mA DC or more(standard)
Down-scale:
-5%, 3.2 mA DC or less
-2.5%, 3.6 mA DC or less(Optional code /F1)
Note: Applicable for Output signal code D and E
IM 01C21C01-01E
Communication Requirements “◊”: Housing;
BRAIN Low copper cast-aluminum alloy with
Communication Distance; polyurethane paint (Munsell 0.6GY3.1/2.0)
Up to 2 km (1.25 miles) when using CEV Degrees of Protection
polyethylene-insulated PVC-sheathed IP67, NEMA4X
cables. Cover O-rings;
Communication distance varies depending Buna-N, Fluoro-rubber (option)
on type of cable used. Data plate and tag;
Load Capacitance; SUS304 or SUS316(optional)
0.22 μF or less (see note) Fill Fluid;
Load Inductance; Silicone or Fluorinated oil (optional)
3.3 mH or less (see note) Weight:
Input Impedance of communicating device; EJA210A with 150# flange 11 kg(25 lb)
10 kΩ or more at 2.4 kHz. EJA220A with 150# flange 16 kg(35 lb)
Note: For general-use and Flameproof type. For Connections:
Intrinsically safe type, please refer to ‘Optional
Specifications.’ Refer to the ‘Model and Suffix Codes’ to
specify the process and electrical connection
HART
type.
Communication Distance;
The high pressure side is a flange
Up to 1.5 km (1 mile) when using multiple
connected, and low side is threaded.
twisted pair cables. Communication distance
varies depending on type of cable used. Atmospheric
100{14.5} pressure
Use the following formula to determine cable
length for specific applications: Working
pressure
65 x 106 (Cf + 10,000) kPa abs
L= − {psi abs}
(R x C) C Applicable range
Where: 10{1.4}
L = length in meters or feet

R = resistance in Ω (including barrier 2.7{0.38}
resistance)
C = cable capacitance in pF/m or pF/ft 1{0.14}
Cf = maximum shunt capacitance of -40 0 40 80 120
(-40) (32) (104) (176) (248)
receiving devices in pF/m or pF/ft
Process temperature °C (°F)
F1001.ai
 Physical Specifications Figure 10.1 Working Pressure and Process

Temperature
Wetted Parts Materials:
High side: < Settings When Shipped > “◊”
See ‘Model and Suffix Codes’ Tag Number As specified in order *1
Low side: Output Mode ‘Linear’
Diaphragm; Display Mode ‘Linear’
Hastelloy C-276 ‘Normal’ unless otherwise
Operation Mode
Cover flange; specified in order
SCS14A Damping Time
‘2 sec.’
Process connector; Constant
Calibration Range
SCS14A Lower Range Value
As specified in order
Capsule gasket;
Calibration Range
Teflon-coated SUS316L As specified in order
Higher Range Value
Drain/Vent plug; Selected from mmH2O, mmAq,
SUS316 Calibration Range
mmWG, mmHg, Pa, hPa, kPa,
Process connector gasket; MPa, mbar, bar, gf/cm2, kgf/cm2,
Units
inH2O, inHg, ftH2O, or psi.
PTFE Teflon (Only one unit can be specified)
Non-wetted Parts Materials: *1: Up to 16 alphanumeric characters (including - and · ) will
Bolting; be entered in the amplifier memory.
SCM435, SUS630, or SUH660
IM 01C21C01-01E
10.2 Model and Suffix Codes
 Model EJA210A
Model Suffix Codes Description
EJA210A .............................. Flange-mounted differential pressure transmitter
(Flush diaphragm type)
Output -D . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
Signal -E . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART protocol, see IM 01C22T01-01E)
-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (FOUNDATION Fieldbus protocol, see IM 01C22T02-01E)
-G . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (PROFIBUS PA protocol, see 01C22T03-00E)
Measurement M . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 100 kPa {100 to 10000 mmH2O}
span (capsule) H . . . . . . . . . . . . . . . . . . . . . . . . . 5 to 500 kPa {0.05 to 5 kgf/cm2}
High pressure [Diaphragm] [Others]
side (Process S*2 . . . . . . . . . . . . . . . . . . . . . . SUS316L SUS316
flange side) H*2 . . . . . . . . . . . . . . . . . . . . . . Hastelloy C-276 Hastelloy C-276
Wetted parts T*2 . . . . . . . . . . . . . . . . . . . . . . Tantalum Tantalum
material *1 W*3 . . . . . . . . . . . . . . . . . . . . . Hastelloy C-276 SUS316
Process flange rating J1 . . . . . . . . . . . . . . . . . . . JIS10K
J2 . . . . . . . . . . . . . . . . . . . JIS20K
A1 . . . . . . . . . . . . . . . . . . . ANSI Class 150
A2 . . . . . . . . . . . . . . . . . . . ANSI Class 300
P1 . . . . . . . . . . . . . . . . . . . JPI Class150
P2 . . . . . . . . . . . . . . . . . . . JPI Class 300
D2 . . . . . . . . . . . . . . . . . . . DIN PN10/16
D4 . . . . . . . . . . . . . . . . . . . DIN PN25/40
Process flange D . . . . . . . . . . . . . . . . . 3-inch (80 mm) /S25C
size/material E . . . . . . . . . . . . . . . . . 3-inch (80 mm) /SUS304
F . . . . . . . . . . . . . . . . . 3-inch (80 mm) /SUS316
A . . . . . . . . . . . . . . . . . 2-inch (50 mm) /SU25C
B . . . . . . . . . . . . . . . . . 2-inch (50 mm) /SUS304
C . . . . . . . . . . . . . . . . . 2-inch (50 mm) /SUS316
Low pressure side process 0 . . . . . . . . . . . . . . . without process connector (Rc1/4 female on the cover flanges)
connection 1 . . . . . . . . . . . . . . . with Rc1/4 female process connector
2 . . . . . . . . . . . . . . . with Rc1/2 female process connector
3 . . . . . . . . . . . . . . . with 1/4 NPT female process connector
4 . . . . . . . . . . . . . . . with 1/2 NPT female process connector
5 . . . . . . . . . . . . . . . without process connector (1/4 NPT female on the cover flanges)
Bolts and nuts material A . . . . . . . . . . . . SCM435
B . . . . . . . . . . . . SUS630
C . . . . . . . . . . . . SUH660
Installation -9 . . . . . . . . . Horizontal impulse piping type, left side high pressure
Electrical connection 0 . . . . . . . G1/2 female, one electrical connection
2 . . . . . . . 1/2 NPT female, two electrical connections without blind plug
3 . . . . . . . Pg 13.5 female, two electrical connections without blind plug
4 . . . . . . . M20 female, two electrical connections without blind plug
5 . . . . . . . G1/2 female, two electrical connections and a blind plug
7 . . . . . . . 1/2 NPT female, two electrical connections and a blind plug
8 . . . . . . . Pg 13.5 female, two electrical connections and a blind plug
9 . . . . . . . M20 female, two electrical connections and a blind plug
A . . . . . . . G1/2 female, two electrical connections and a SUS316 blind plug
C . . . . . . . 1/2 NPT female, two electrical connections and a SUS316 blind plug
D . . . . . . . M20 female, two electrical connections and a SUS316 blind plug
Integral indicator D . . . Digital indicator
E . . . Digital indicator with the range setting switch
N . . . (None)
— N Always N
Optional codes / Optional specification
Example: EJA210A-DMSA1D5A-92NN/
*1: Low pressure side wetted parts material: Cover flange; SCS14A, Process connector; SCS14A, Capsule; SUS316L (Diaphragm;
Hastelloy C-276), Vent plug; SUS316
*2: Applicable only for 3-inch (80 mm) flange size (Process flange size/material codes D and E)
*3: Applicable only for 2-inch (50 mm) flange size (Process flange size/material codes A and B)
IM 01C21C01-01E
 Model EJA220A
Model Suffix Codes Description
EJA220A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flange-mounted differential pressure transmitter
(Extended diaphragm type)
Output -D . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
Signal -E . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART protocol, see IM 01C22T01-01E)
-F . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (FOUNDATION Fieldbus protocol, see IM 01C22T02-01E)
-G . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (PROFIBUS PA protocol, see 01C22T03-00E)
Measurement M . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 100 kPa {100 to 10000 mmH2O}
span (capsule) H . . . . . . . . . . . . . . . . . . . . . . . . . 5 to 500 kPa {0.05 to 5 kgf/cm2}
High pressure [Diaphragm] [Pipe] [Others]
side (Process S*2 . . . . . . . . . . . . . . . . . . . . . . SUS316L SUS316 SUS316
flange side) W*3 . . . . . . . . . . . . . . . . . . . . . Hastelloy C-276 SUS316 SUS316
Wetted parts
material *1
Process flange rating J1 . . . . . . . . . . . . . . . . . . JIS10K
J2 . . . . . . . . . . . . . . . . . . JIS20K
A1 . . . . . . . . . . . . . . . . . . ANSI Class 150
A2 . . . . . . . . . . . . . . . . . . ANSI Class 300
P1 . . . . . . . . . . . . . . . . . . JPI Class150
P2 . . . . . . . . . . . . . . . . . . JPI Class 300
D2 . . . . . . . . . . . . . . . . . . DIN PN10/16
D4 . . . . . . . . . . . . . . . . . . DIN PN25/40
Diaphragm extension 2 . . . . . . . . . . . . . . . . . X2=50 mm
length (X2) 4 . . . . . . . . . . . . . . . . . X2=100 mm
6 . . . . . . . . . . . . . . . . . X2=150 mm
Process flange G . . . . . . . . . . . . . . . 4-inch (100 mm) / S25C
size/material H . . . . . . . . . . . . . . . 4-inch (100 mm) / SUS304
J . . . . . . . . . . . . . . . 4-inch (100 mm) / SUS316
D . . . . . . . . . . . . . . . 3-inch (80 mm) / S25C
E . . . . . . . . . . . . . . . 3-inch (80 mm) / SUS304
F . . . . . . . . . . . . . . . 3-inch (80 mm) / SUS316
Low pressure side process 0 . . . . . . . . . . . . without process connector (Rc1/4 female on the cover flanges)
connection 1 . . . . . . . . . . . . with Rc1/4 female process connector
2 . . . . . . . . . . . . with Rc1/2 female process connector
3 . . . . . . . . . . . . with 1/4 NPT female process connector
4 . . . . . . . . . . . . with 1/2 NPT female process connector
5 . . . . . . . . . . . . without process connector (1/4 NPT female on the cover flanges)
Bolts and nuts material A . . . . . . . . . SCM435
B . . . . . . . . . SUS630
C . . . . . . . . . SUH660
Installation -9 . . . . . . . Horizontal impulse piping type, left side high pressure
Electrical connection 0 . . . . . . G1/2 female, one electrical connection
2 . . . . . . 1/2 NPT female, two electrical connections without blind plug
3 . . . . . . Pg 13.5 female, two electrical connections without blind plug
4 . . . . . . M20 female, two electrical connections without blind plug
5 . . . . . . G1/2 female, two electrical connections and a blind plug
7 . . . . . . 1/2 NPT female, two electrical connections and a blind plug
8 . . . . . . Pg 13.5 female, two electrical connections and a blind plug
9 . . . . . . M20 female, two electrical connections and a blind plug
A . . . . . . G1/2 female, two electrical connections and a SUS316 blind plug
C . . . . . . 1/2 NPT female, two electrical connections and a SUS316 blind plug
D . . . . . . M20 female, two electrical connections and a SUS316 blind plug
Integral indicator D . . . Digital indicator
E . . . Digital indicator with the range setting switch
N . . . (None)
— N.. Always N
Optional codes / Optional specification
Example: EJA220A-DMSA12G5A-92NN/
*1: Low pressure side wetted parts material: Cover flange; SCS14A, Process connector; SCS14A, Capsule; SUS316L (Diaphragm,
Hastelloy C-276), Vent plug ; SUS316
*2: Applicable only for 4-inch (100 mm) flange size (Process flange size/material codes G and H).
*3: Applicable only for 3-inch (80 mm) flange size (Process flange size/material codes D and E).
IM 01C21C01-01E
10.3 Optional Specifications
For FOUNDATION Fieldbus explosion protected type, see IM 01C22T02-01E.
For PROFIBUS PA explosion protected type, see IM 01C22T03-00E.
Item Description Code
FM Explosionproof Approval *1
Explosionproof for Class I, Division 1, Groups B, C and D
Dust-ignitionproof for Class II/III, Division 1, Groups E, F and G
FF1
Hazardous (classified) locations, indoors and outdoors (NEMA 4X)
Temperature class: T6
Amb. Temp.: –40 to 60°C (–40 to 140°F)
FM Intrinsically safe Approval *1
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1,
Groups E, F & G and Class III, Division 1 Hazardous Locations.
Factory Mutual (FM)
Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division. 2,
Groups E, F & G, and Class III, Division 1 Hazardous Locations.
Enclosure: “NEMA 4X”, Temp. Class: T4, Amb. Temp.: –40 to 60°C (–40 to 140°F) FS1
Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G]
Vmax=30 V, Imax=165 mA, Pmax=0.9 W, Ci=22.5 nF, Li=730 µH
[Groups C, D, E, F and G]
Combined FF1 and FS1 *1 FU1
ATEX Flameproof Approval *2
Certificate: KEMA 02ATEX2148
II 2G Exd IIC T4, T5, T6 KF21
Amb. Temp.: T5; –40 to 80°C (–40 to 176°F), T4 and T6; –40 to 75°C (–40 to 167°F)
ATEX Max. process Temp.: T4; 120°C (248°F), T5; 100°C (212°F), T6; 85°C (185°F)
ATEX Intrinsically safe Approval *2
Certificate: KEMA 02ATEX1030X
KS2
II 1G EEx ia IIC T4, Amb. Temp.: –40 to 60°C (–40 to 140°F)
Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 µH
CSA Explosionproof Approval *1
Certificate: 1089598
Explosionproof for Class I, Division 1, Groups B, C and D
Dustignitionproof for Class II/III, Division 1, Groups E, F and G
Division2 ‘SEALS NOT REQUIRED’ , Temp. Class: T4, T5, T6 Encl Type 4x
Max. Process Temp.: T4; 120°C (248°F), T5; 100°C (212°F), T6; 85°C (185°F) CF1
Amb. Temp.: –40 to 80°C (–40 to 176°F)
Process Sealing Certification
Dual seal certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation : at the zero
adjustment screw
Canadian Standards
CSA Intrinsically safe Approval *1
Association (CSA)
Certificate: 1053843
Intrinsically Safe for Class I, Groups A, B, C and D Class II and III, Groups E, F and G
Nonincendive for Class I, Division 2, Groups A, B, C and D Class II, Division 2,
Groups F and G and Class III (not use Safety Barrier)
Encl Type 4x, Temp. Class: T4, Amb. Temp.: –40 to 60°C (–40 to 140°F) CS1
Process Sealing Certification
Dual seal certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation : at the zero
adjustment screw
Combined CF1 and CS1 *1 CU1
IM 01C21C01-01E
IECEx Intrinsically safe, type n and Flameproof Approval *3
Intrinsically safe and type n
Certificate: IECEx KEM 06.0007X
Ex ia IIC T4, Ex nL IIC T4 Enclosure: IP67
Amb. Temp.: –40 to 60°C (–40 to 140°F), Max. Process Temp.: 120°C (248°F)
Electrical Parameters:
[Ex ia] Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 µH
IECEx Scheme SU2
[Ex nL] Ui=30 V, Ci=22.5 nF, Li=730 µH
Flameproof
Certificate: IECEx KEM 06.0005
Ex d IIC T6...T4 Enclosure: IP67
Max.Process Temp.: T4;120°C (248°F), T5;100°C (212°F), T6; 85°C (185°F)
Amb.Temp.: –40 to 75°C (–40 to 167°F) for T4, –40 to 80°C (–40 to 176°F) for T5,
–40 to 75°C (–40 to 167°F) for T6
*1: Applicable for Electrical connection code 2 and 7 (1/2 NPT female).
*2: Applicable for Electrical connection code 2, 4, 7 and 9 (1/2 NPT and M20 female).
*3: Applicable for Electrical connection code 2, 4 and 7 (1/2 NPT and M20 female).
IM 01C21C01-01E
Amplifier cover only P
Color change
Painting Amplifier cover and terminal cover, Munsell 7.5 R4/14 PR
Coating change Epoxy resin-baked coating X1
Exterior parts on the amprifier housing (name plates, tag plate, zero-adjustment
316 SST exterior parts HC
screw, stopper screw) will become 316 or 316L SST.
Fluoro-rubber O-ring All O-rings of amplifier housing. Lower limit of ambient temperature : –15 °C (5 °F) HE
Transmitter power supply voltag: 10.5 to 32 V DC (10.5 to 30 V DC for intrinsically
safe type, 9 to 32 V DC for FOUNDATION Fieldbus and PROFIBUS PA communication
Lightning protector A
type.)
Allowable current: Max. 6000 A (1×40 µs), Repeating 1000 A (1×40 µs), 100 times
Degrease cleansing treatment K1
Oil-prohibited use Degrease cleansing treatment with fluorinated oil filled capsule.
K2
Operating temperature –20 to 80 °C
Degrease cleansing and dehydrating treatment K5
Oil-prohibited use with
dehydrating treatment Degrease cleansing and dehydrating treatment with fluorinated oil filled capsule.
K6
Operating temperature –20 to 80 °C
P calibration (psi unit ) D1
(See Table for Span and Range
Calibration units bar calibration (bar unit ) D3
Limits.)
M calibration (kgf/cm2 unit ) D4
Sealing treatment to Sealant (liquid silicone rubber) is coated on SUS630 cover flange mounting nuts
Y
SUS630 nuts against stress corrosion cracking.
No serration No serration work on the flange gasket surface ( for ANSI flange only ) Q
With FEP film and fluorinated oil.
Teflon film Working range: 20 to 120 °C, 0 to 2 MPa {0 to 20 kgf/cm2} T
(Not usable under vacuum )
Fast response *2 Update time: 0.125 sec or less, see GS for response time F1
Failure alarm
Output status at CPU failure and hardware error is –5%, 3.2 mA or less. C1
down-scale *1
Failure alarm down-scale: output status at CPU failure and
C2
NAMUR NE43 Output signal limits: hardware error is –5%, 3.2 mA or less.
compliant *1 3.8 mA to 20.5 mA Failure alarm up-scale: output status at CPU failure and
C3
hardware error is 110%, 21.6 mA or more.
Data configuration at
Description into “Descriptor” parameter of HART protocol CA
factory
Stainless steel amplifier Amplifier housing material: SCS14A stainless steel
E1
housing (equivalent to SUS316 cast stainless steel or ASTM CF-8M)
Gold-plate Gold-plated diaphragm for high pressure side (process flange side) A1
Stainless steel tag plate SUS 304 stainless steel tag plate wired onto transmitter N4
High pressure side: Process flange, Block
M03
Low pressure side: Cover flange For model
High pressure side: Process flange, Block EJA210A
M13
Low pressure side: Cover flange, Process connector
Mill Certificate
High pressure side: Process flange, Block, Pipe, Base
M04
Low pressure side: Cover flange For model
High pressure side: Process flange, Block, Pipe, Base EJA220A
M14
Low pressure side: Cover flange, Process connector
( Flange rating ) ( Test Pressure )
JIS 10K 2 MPa {20 kgf/cm2 } T31
Pressure test/Leak test JIS 20K 5 MPa {50 kgf/cm2 } T32
Certificate Nitrogen(N2) Gas
ANSI/JPI class 150 3 MPa {29.8 kgf/cm2 } T36
Retention time: 10 minutes
ANSI/JPI class 300 7.7 MPa {77 kgf/cm2 } T37
ANSI/JPI class 300 7 MPa {70 kgf/cm2 } T38
*1: Applicable for Output signal code D and E. The hardware error indicates faulty amplifier or capsule. When combining with Optional
code F1, output status for down-scale is –2.5%, 3.6 mA DC or less.
* 2: Applicable for Output signal code D and E. Write protection switch is attached for Output code E.
IM 01C21C01-01E
10.4 Dimensions
 Model EJA210A
Unit: mm (approx. inch)
174 (6.85) 30 (1.18)
110 (4.33)
External indicator
conduit connection 133 (5.24) Conduit Zero 35
connection adjustment (1.38)
Blind plug
(Optional) 25 Internal Terminal side
(0.98) indicator ø78
t (Optional) (3.07)
163 146
(6.42) (5.75)
Ground
Shrouding bolt *2 terminal
øD øC øg ød *1
Vent plug
46 Drain plug
Process
(1.81) connector n- øh
(Optional) 54
Process flange (2.13)
*1 Indicates inside diameter of gasket contact surface.

*2 Applicable only for ATEX and IECEx Flameproof type.
Flange size: 3-inch (80 mm)

Flange Nominal Bolt Holes
Diameter and øD øC øg ød t
Rating No.(N) Dia.(øh)
80 mm JIS 10K 185(7.28) 150(5.91) 130(5.12) 90(3.54) 18(0.71) 8 19(0.75)
80 mm JIS 20K 200(7.87) 160(6.30) 130(5.12) 90(3.54) 22(0.87) 8 23(0.91)
3-inch ANSI Class150 190.5(7.50) 152.4(6.00) 130(5.12) 90(3.54) 23.9(0.94) 4 19.1(0.75)
3-inch ANSI Class300 209.6(8.25) 168.1(6.62) 130(5.12) 90(3.54) 28.5(1.12) 8 22.4(0.88)
3-inch JPI Class150 190(7.48) 152.4(6.00) 130(5.12) 90(3.54) 24(0.44) 4 19(0.75)
3-inch JPI Class300 210(8.27) 168.1(6.62) 130(5.12) 90(3.54) 28.5(1.12) 8 22(0.87)
3-inch DIN PN 10/16 200(7.87) 160(6.30) 130(5.12) 90(3.54) 20(0.79) 8 18(0.71)
3-inch DIN PN 25/40 200(7.87) 160(6.30) 130(5.12) 90(3.54) 24(0.44) 8 18(0.71)

Diameter and øD øC øg ød t
50 mm JIS 10K 155(6.10) 120(4.72) 100(3.94) 61(2.40) 16(0.63) 4 19(0.75)
50 mm JIS 20K 155(6.10) 120(4.72) 100(3.94) 61(2.40) 18(0.71) 8 19(0.75)
2-inch ANSI Class150 152.4(6.00) 120.7(4.75) 100(3.94) 61(2.40) 19.1(0.75) 4 19.1(0.75)
2-inch ANSI Class300 165.1(6.50) 127(5.00) 100(3.94) 61(2.40) 22.4(0.88) 8 19.1(0.75)
2-inch JPI Class150 152(5.98) 120.6(4.75) 100(3.94) 61(2.40) 19.5(0.71) 4 19(0.75)
2-inch JPI Class300 165.1(6.50) 127(5.00) 100(3.94) 61(2.40) 22.5(0.89) 8 19(0.75)
2-inch DIN PN 10/16 165(6.50) 125(4.92) 100(3.94) 61(2.40) 18(0.71) 4 18(0.71)
2-inch DIN PN 25/40 165(6.50) 125(4.92) 100(3.94) 61(2.40) 20(0.79) 4 18(0.71)

F1002.ai
IM 01C21C01-01E
 Model EJA220A
Unit: mm (approx. inch)
174 (6.85) 30 (1.18)
110 (4.33)
External indicator
conduit connection 133 (5.24) Conduit Zero 35
connection adjustment
Blind plug (1.38)
(Optional) Internal Terminal side
indicator
ø78
(Optional) (3.07)
163 146
(6.42) (5.75)
Shrouding bolt *1 Ground

terminal
øD øC øg øA
Process
connection Vent plug
46
Drain plug
(1.81) Process
connector n- øh
(Optional) 54
t Process flange
(2.13)
25 (0.98)
X2
*1 Applicable only for ATEX and IECEx Flameproof type.

Diameter and øD øC øg øA t
100 mm JIS 10K 210(8.27) 175(6.89) 155(6.10) 96(3.78) 18(0.71) 8 19(0.75)

100 mm JIS 20K 225(8.86) 185(7.28) 155(6.10) 96(3.78) 24(0.94) 8 23(0.91)
4-inch ANSI Class150 228.6(9.00) 190.5(7.50) 155(6.10) 96(3.78) 23.9(0.94) 8 19.1(0.75)
4-inch ANSI Class300 254(10.00) 200(7.87) 155(6.10) 96(3.78) 31.8(1.25) 8 22.4(0.88)
4-inch JPI Class150 229(9.02) 190.5(7.50) 155(6.10) 96(3.78) 24(0.94) 8 19(0.75)
4-inch JPI Class300 254(10.00) 200.2(7.88) 155(6.10) 96(3.78) 32(1.26) 8 22(0.87)
4-inch DIN PN 10/16 220(8.66) 180(7.09) 155(6.10) 96(3.78) 20(0.79) 8 18(0.71)
4-inch DIN PN 25/40 235(9.25) 190(7.50) 155(6.10) 96(3.78) 24(0.94) 8 22(0.87)

Diameter and øD øC øg øA t
80 mm JIS 10K 185(7.28) 150(5.91) 130(5.12) 71(2.80) 18(0.71) 8 19(0.75)
80 mm JIS 20K 200(7.87) 160(6.30) 130(5.12) 71(2.80) 22(0.87) 8 23(0.91)
3-inch ANSI Class150 190.5(7.50) 152.4(6.00) 130(5.12) 71(2.80) 23.9(0.94) 4 19.1(0.75)
3-inch ANSI Class300 209.6(8.25) 168.1(6.62) 130(5.12) 71(2.80) 28.5(1.12) 8 22.4(0.88)
3-inch JPI Class150 190(7.48) 152.4(6.00) 130(5.12) 71(2.80) 24(0.94) 4 19(0.75)
3-inch JPI Class300 210(8.27) 168.1(6.62) 130(5.12) 71(2.80) 28.5(1.12) 8 22(0.87)
3-inch DIN PN 10/16 200(7.88) 160(6.30) 130(5.12) 71(2.80) 20(0.79) 8 18(0.71)
3-inch DIN PN 25/40 200(7.87) 160(6.30) 130(5.12) 71(2.80) 24(0.94) 8 18(0.71)
Diaphragm Extension Length Code X2
2 1.97 inch (50 mm)
4 3.94 inch (100 mm)
6 5.91 inch (150 mm)

F1003.ai
IM 01C21C01-01E
Customer DPharp EJA Series
Maintenance Transmitter Section
Parts List
2 5
4
11
A 10
12
13 1
2 2
1
14
A
6
7-2
7-1 5
8 9
Item Part No. Qty Description

1 Bellow 2 Cover
F9341RA Cast-aluminum alloy
F9341RJ SCS14A stainless steel
2 F9341JP 2 O-ring
3 Below 1 Case Assembly (Note 1)
F9341AA Cast-aluminum alloy for G1/2

F9341AC Cast-aluminum alloy for G1/2 (two electrical connections)
F9341AE Cast-aluminum alloy for 1/2 NPT (two electrical connections)
F9341AH Cast-aluminum alloy for M20 (two electrical connections)
F9341AJ Cast-aluminum alloy for Pg13.5 (two electrical connections)
F9341AR SCS14A stainless steel for 1/2 NPT (two electrical connections)
4 — 1 Name Plate
5 Bellow 4 Screw
F9900RG For cast-aluminum alloy case assembly
F9900RR For SCS14A stainless steel case assembly
6 F9341KL 1 Tag Plate

7-1 Below 1 CPU Assembly
F9342AB For BRAIN protocol version
F9342AL For HART protocol version
F9342AF For BRAIN protocol version(Optional code /F1)
F9342AM For HART protocol version with write protection switch (Optional code /F1)
7-2 F9342BF 1 For FOUNDATION Fieldbus protocol version
F9342BG For FOUNDATION Fieldbus protocol version with PID/LM function (Optional code /LC1)
8 F9900RP 2 Cap Screw
9 Y9612YU 2 Screw
10 Below 1 Plug
F9340NW For Pg13.5
F9340NX For M20
G9330DP For G1/2
G9612EB For 1/2 NPT
11 Bellow 1 Cover Assembly

F9341FM Cast-aluminum alloy
F9341FJ SCS14A stainless steel
12 Below 1 LCD Board Assembly
F9342BL Without range-setting switch For integral indicator
F9342BM With range-setting switch

13 F9342MK 2 Mounting Screw
14 F9300PB 2 Label
(Note 1) Applicable for BRAIN and HART protocol versions (Output signal code D and E). For FOUNDATION Fieldbus protocol version (Output
signal code F), consult Yokogawa local office.
All Rights Reserved. Copyright © 1997, Yokogawa Electric Corporation

CMPL 01C21A01-02E
Subject to change without notice.
11th Edition: Oct. 2008 (YK)
Customer Model EJA210A and EJA220A
Flange Mounted Differential
Maintenance Pressure Transmitter
Parts List (Pressure-detector Section)
EJA210A EJA220A
8
5
3
9
4
2 6
10
7
Item Part No. Qty Description
1 F9300AJ 1 O-Ring
2 Below 1 Gasket
D0114RB PTFE Teflon
U0102XC PTFE Teflon (degreased)
3 Below 1 Process Connector, SCS14A Stainless Steel (Note 1)
F9340XY Rc 1/4
F9340XW Rc 1/2
F9340XZ 1/4 NPT
F9340XX 1/2 NPT
4 Below 2 Bolt
X0100MN SCM435 Chrome Molybdenum Steel

F9273DZ SUS630 Stainless Steel
F9340AZ SUH660 Stainless Steel
5 Below 1 Vent Plug, SUS316 Stainless Steel
F9340SA R 1/4
F9340SB 1/4 NPT

6 D0114PB 1 Vent Screw, SUS316 Stainless Steel
7 Below 1 Drain Plug, SUS316 Stainless Steel (Note 1)
F9200CS R 1/4
D0114RZ 1/4 NPT
8 Below 1 Vent Plug (degreased), SUS316 Stainless Steel

F9275EC R 1/4
F9275ED 1/4 NPT
9 F9275EE 1 Needle Assembly (degreased), SUS316 Stainless Steel
10 Y9625YU 2 Bolt
(Note 1) In case of degrease cleansing treatment (Optional Code/K1, K2, K5 and K6), consult YOKOGAWA local office.
All Rights Reserved. Copyright © 1997, Yokogawa Electric Corporation

CMPL 01C21C01-01E
Subject to change without notice.
4th Edition: July 2001 (YK)
Revision Information
 Title : Model EJA210A and EJA220A
Flange Mounted Differential Pressure Transmitter
 Manual No. : IM 01C21C01-01E
Edition Date Page Revised Item

1st June 1997 — New publication
2nd Mar. 1998 CONTENTS Page 3 Add REVISION RECORD.
1-1 1 Add ‘NOTE’ notice for FOUNDATION Fieldbus and HART protcol
versions.
6-1 6.1 Add Item to the Wiring Precautions.
11-1 11.1 Add FOUNDATOIN Fieldbus protocol.
11-3 11.2 Add Output signal code F.
11-6 11.3 Add Optional code A1.
2-9+ Change the figure of terminal configuration.
CMPL CMPL 1C21A1-02E 1st → 2nd
Page 2 Add Item 7-2.
3rd Sep. 1998 — Changed to Electronic File Format.
2-13 2.10 Delete EMC Conformity Standards Tables.
8-17 8.3.2(9) Correction made in BURN OUT figure.
11-3, 11-4 11.2 Add Process flange size / material code F and C.
Add Electrical connection code 7, 8, and 9.
Add Process flange size / material code F and J.
Add Electrical connection code 7, 8, and 9.
CMPL CMPL 1C21A1-02E 2nd → 3rd
Page 2 Add Part No. to Item 3 (For PG13.5 and M20).
Add Part No. to Item 10 (For 1/2NPT, PG13.5, and M20).
4th Oct. 1999 — Revised a book in a new format.
(The location of contents and the associated page numbers may
not coincide with the one in old editions.)
2-8 2.10 Add AS/NZS 2064 1/2 to EMI, EMC Conformity Standards.
8-4 8.3.1 Move Parameter Summary table to Chapter 8.
CMPL CMPL 1C21A1-02E 3rd → 4th
Change a format.
CMPL 1C21C1-01E 1st → 2nd
Change a format.
5th Sep. 2000 2-8 2.9.4b Change contents of NOTE 1.
2-9 2.9.4b Change contents of NOTE 4.
8-5 8.3.1 Add footnote 2 and 3.
10-2 10.1 Add calibration units of Pa and hPa.
10-3 10.2 Add Bolts and nuts material code C.
10-4 Add Bolts and nuts material code C.
10-5 10.3 Add Amb. Temp. for T6: –40 to 75°C
10-6 Add Optional code /F1 and /N4.
CMPL CMPL 1C21A1-02E 4th → 5th(Manual Change)
Add part numbers to 7-1 CPU Assembly.
F9342AF and F9342AM
CMPL 1C21A1-02E 5th → 6th
Add part numbers to 7-2 CPU Assembly.
F9342BG
Change part number of 7-1 CPU Assembly.
F9342BC → F9342BB
Change part number of 10 Plug
G9330DK → G9330DP
CMPL 1C21C1-01E 2nd → 3rd
Add part number to 4 Bolt.
F9340AZ
IM 01C21C01-01E
Edition Date Page Revised Item
6th July 2001 2-10 2.10 Change EMC Conformity number.
8-4, 8-5 8.3.1 Add footnote (*4) to B40, Maximum static pressure in Parameter
Summary.
CMPL CMPL 1C21A1-02E 6th → 7th(Manual Change)
Change Part No. of 7-1 CPU Assembly for BRAIN protocol.
F9342BB → F9342AB
CMPL 1C21A1-02E 7th → 8th(Manual Change)
Change Part No. of 7-1 CPU Assembly for HART protocol.
F9342BH → F9342AL
CMPL 1C21A1-02E 8th → CMPL 01C21A01-02E 9th
Delete Part No. of 4 Name Plate.
Change Part No. of 5 Screw.
F9303JU → Y9303JU
CMPL 1C21C1-01E 3rd → CMPL 01C21C01-01E 4th
7th May 2002 1-2 1.1 Add “1.1 For Safety Using.”
2-7 2.9.4 Add descriptions based on ATEX directive.
10-5 10.3 Add Optional code K2.
10-6 Add Optional code C2 and C3.
8th Apr. 2003 2-8 2.9.4 Add Option code KU2.
2-10 2.11 Add PED (Pressure Equipment Directive).
10-5 10.3 Add Option code KU2.
9th Apr. 2006 1-2 1.1 Add (e) Explosion Protected Type Instrument and (f) Modification
1-3 1.3 Add “1.3 ATEX Document”
2-6 2.9.3 Add “IECEx Certification” and delete “SAA Certification”
2-11 2.12 Add Low Voltage Directive
10-5, 10-6 10.3 Add Certificate numbers and Applicable standards
10-6 Add option code /SU2 and delete option code /SU1
10-7 Add option code /PR
10th Jan. 2008 1-1 Add direct current symbol.
1-4 Add 11 European languages for ATEX documentation.
2-3+ 2.9.1 Add applicable standard and certificate number for appovals.
2-10 2.10 Add EMC caution note.
4-2 4.4 Add section of changing the direction of integral indicator.
8-14 8.3.3(12) Add figure for A40.
9-3 9.4.1 Add figure of integral indicator direction.
10-1+ 10.1, 10.2 Add PROFIBUS PA communication type.
10-5,10-6 10.3 Delete applicable standard from the table.
CMPL CMPL 01C21A01-02E 9th → 10th
Delete logo from the tag plate.
11th Oct. 2008 2-9 2.9.4 Change explosion protection marking for type n from EEx to Ex.
2-10 2.10 Update EMC conformity standards.
8-4, 8-5 8.3.1 Add new parameters.
8-6 8.3.2 Add items in table 8.3.1.
8-9 and later 8.3.3 Add (5)Change Output Limits and (14)Span Adjustment.
Re-number the items.
8-18 8.5.2 Modify descriptions and notes for Er.01.
9-1 9.3 Add note for calibration.
9-5 9.4.3 Add note for cleaning.
10-3, 10-4 10.2 Add new suffix codes.
10-6, 10-7 10.3 Add sealing statement for CSA standards. Add /HC.
CMPL CMPL 01C21A01-02E 10th → 11th
Change Part No. of items 5 and 8.
12th July 2015 2-5, 2-6 2.9.2 Add temperature limitation for /HE.
2-9 to 2-10 2.9.4 b Change /KF2 to /KF21 and modify descriptions. Delete c. Replace
tag plate.
2-11 2.10 Add standards.
2-12 2.12 Add (3) and (4).
8-1 8.1.1 Add note. 8.1.2 Add descriptions.
10-1 10.1 Add information to “EMC Conformity Standards”.
10-5 to 10-7 10.3 Delete codes KU2 and KF2. Add KF21. Add Codes HE and CA.
IM 01C21C01-01E

Cambi e Nap Yokogawa

Uploaded by

Copyright:

Available Formats

Cambi e Nap Yokogawa

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cambi e Nap Yokogawa

Uploaded by

Copyright:

Available Formats

User’s

Manual Model EJA210A and EJA220A

Model EJA210A and EJA220A

IM 01C21C01-01E 12th Edition

12th Edition: July 2015 (KP) IM 01C21C01-01E

• The following safety symbol marks are used in

The model name and specifications are indicated

F0202.ai (a) Ambient Temperature

• Instrument installed in the process is

Non-Hazardous Hazardous Locations Division 1

• Type of Protection and Marking Code:

EJA Series Pressure IECEx Certified

*1: In any safety barriers used the output current must be

ANSI 1/2 NPT female A

 Tag plate for flameproof type

Location of the marking

WARNING MODEL: Specified model code.

(5) Maintenance and Repair

2.11 PED (Pressure Equipment (3) Operation

(1) Pollution Degree 2

External indicator Conduit connection

Amplifier Cover Setting pin (CN4) Burn - out Output at

Table 3.1 Display Symbol

Figure 4.2 Rotating Transmitter Section

Figure 4.1 Transmitter Mounting

An integral indicator can be installed in the following

PART No. Prosess Flange size

F9347XA 3 inch (80mm)

Figure 4.3 Integral Indicator Direction F0403.ai

Figure 4.4 Affixing the Teflon Film

4.5 Affixing the Teflon Film

5. Installing Impulse Piping

Pipe (opened to atmosphere

Figure 5.2 Impulse Piping Connection Examples

silicone group sealant is recommended.)

Figure 6.2 External Indicator Connection

6.2 Selecting the Wiring 6.3.3 BRAIN TERMINAL BT200

6.4 Wiring 6.4.2 Wiring Installation

6.4.1 Loop Configuration (1) General-use Type and Intrinsically Safe

(1) General-use Type and Flameproof Type Flexible metal conduit

Receiver Figure 6.7 Typical Wiring Using Flexible Metal

Figure 6.5 Connection between Transmitter and

Flexible metal conduit Transmitter terminal box

Wiring metal Apply a non-hardening Ground terminal

Figure 6.8 Typical Cable Wiring Using Flameproof

0 10.5 16.4 24.7 42

Figure 6.11 Relationship between Power Supply

Remove the plastic dust cap placed in the

 Verify and Change Transmitter

IMPORTANT  Using the Transmitter Zero-adjustment

match the transmitter output signal with the actual

7.5 Venting or Draining

Figure 7.2 Draining/Venting the Transmitter

8. BRAIN TERMINAL BT200 Operation

• Communication Line Requirements

Load Cable DPharp

● Loop resistance = R + 2Rc

Figure 8.2 Conditions of Communication Line

LCD Alphanumeric keys

Shift keys F0805.ai