Device Serial Number :4CRSXXXX Each output is assigned an alarm that can be 1 : Power 220 VAC release the

1 : Power 220 VAC release the button till the indicator led starts
Device Access Point Name : 4CR4S_cHome armed and when turned into alarm status a 2 : High voltage inputs from 9V to 250 V(AC/DC) blinking, then the board will restart in configuring
Device Access Point Password : 4CRS0010XXXX notification is sent to cHome android app. 3 : Contact inputs mode.
- Product Description : Each output can be scheduled to turn ON or OFF at 4 : Relay outputs (NO /NC), maximum voltage Note : When the device is set on Configuring
This is a 4 channel relays WiFi enabled board, that any time in the week, and each output accepts 5 250 VAC, maximum current 10 Amps mode, this will put it back to it’s factory settings,
allows the control of different electric accessories ON timers and 5 OFF timers daily summing up to a 5 : Reset Button and all previous configuration and previously
from the internet using cHome android app. total of 70 timers per week per output. 6 : Indicator LED programmed timers and automations are reset.
This board contains 4 high voltage inputs that The board accepts 16 Automations that can be 7 : Mounting Hole 3-Connect your android smart phone’s WIFI to the
accept any input from 9V to 250 V (AC & DC), and triggered when n one of the outputs changes status - Configuring the Board : access point 4CR4S_cHome, use the password
has 4 contact inputs. This makes the board and executes an action on an other output, this is 1-To configure the board it needs to be first mentioned on top of Page1.
compatible with all types of switches and most of described in Page12. powered by 220 v AC as described in Page14. 4-Open your phone browser and type the IP
detectors, including but not limited to : motion, - Introducing the Board : 2-When the board is new it comes already set in address : 192.168.4.1, The board will serve the
Gas, Fume, Leak detectors and all types of relay Configuring mode this can be checked by turningg configuring page.
output detectors. 3 your android smart phone’s WIFI ON and searching 5-Fill all the fields 1,2,3,4 in the configuring page,
This board must be configured to work properly, 1 for the access point named : 4CR4S_cHome , if see Figure2.
this is described in Page3. found that means the board is in configuring Field 1 : The SSID of the Access Point that this
This board accepts commands from the inputs as mode and you are ready to go. device will be using to connect to the internet.
4 2
well as from cHome android app, and the status of If you are not able to find the access point you 1
have to set first the board in configuring
nfiguring mode and 2 Figure2
the outputs is updated immediately across all
this can be done by long pressing the reset button 3
paired android apps with the board when the real 7 4
output status has changed. 6 on the board for more than 3 seconds, do not
Figure1 5 Page4
Page1 Page2 Page3

Field 2 : The Password of the Access Point this Also you need to specify the action type of each This is handy if you’d like to reactuate any Click on New Device on the bottom
device will use to connect to the internet. output, there are 3 options : Latch, Pulse, Duration accessory whenever the electricity is lost and then right corner, a new screen will open
Field 4 : Give your Device a name. Latch will keep the output
out relay in its position until comes back, suitable for lights, and outlets where you have to enter the exact
Field 5 : The pairing password that every one who another command is initiated suitable for controlling fridges … etc. Note that you can choose board serial number « refer to page1 »
wants to pair this device with cHome android app controlling lights, outlets … etc to remember the status and not reactuate this will ,enter the pairing password, the same
will use, this must be kept secret. Pulse will actuate the output relay for only one remember the status only and will not reactuate you configured the board with, and
6-Configuring Inputs and Outputs : In this step you second, meaning the output relay will actuate for the relay, suitable for controlling «Les give your new board a name that you
need to choose from the drop down list what is one second to turn ON the accessory and will Telerupteurs »… etc. See Figure4 like to distinguish it from other paired
actually being connected in the INPUT1/2/3/4 of actuate for one second to turn it OFF (it gives a boards. Then click pairing, a coutdown Figure5
the device, this must be accurate. Also you need to pulse for both ON and OFF), suitable for of 10 sec will start, if successful then the 4 outputs
choose which output you wish to control by each controlling : « Les Telerupteurs », and all devices of your board will show on the main screen with
of these inputs . You can choose as many outputs operating with pulse commands. default names , OUT1,.., OUT4 with default icons.
as you want. It is not necessary that INPUT1 Duration will actuate the output relay for the Figure4 See Figure6.You can personalize the name and
controls OUTPUT1 and so on. See Figure3 specified duration in seconds and then will turn it - Pairing the Board with cHome Android app : icon of each output «accessory » by clicking the
OFF, suitable for controlling accessories with limit
limi Head to Google PlayStore and download cHome accessory and clicking the parameters icon on the
switches that don’t need the relay staying ON app. The first time you open the app it will look top right corner of the accessory dashboard, see
when the limit switch is actuated, like electric similar to Figure5.
blinds,
s, electric garage doors … etc. See Figure4 Make sure the board that you want to pair is
Also you can check the box for remember status already configured and powered ON and the
access point it is connecting to is ON and has
Figure3 after power loss and/or reactuate after power loss. Figure7 Figure6
access to the internet.
Figure7.
Page5 Page6 Page7 Page8
If pairing fails, make sure : and can be scheduled to turn OFF 5x7 times a - Configuring automations:
1-Make Sure the board is connected to the access week. To configure an automation click on the
point by checking the onboard indicator LED it In order to program a timer for a specific accessory Automations button at the bottom of the main
Figure8
should be ON all the time and not blinking. you click the clock icon on the dashboard of the screen, a new screen will open that shows a list of
2-Both the board and the phone are connected to accessory then you click schedule then follow already programmed automations for every paired
the internet. these steps : board, click on configure a new automation for the
3-Make sure all parameters entered to the pairing 1-Select the type of timer ON or OFF There are 3 timer types : schedule, Duration, board that you like, a new screen will open where
screen are exact and correct. 2-Select the day using the UP and Down arrows. Delay, See Figure 9 you will have to choose the trigger event of the
4-If the internet connection is very slow pairing 3-Select one timer from below by cicking a gray condition that needs to be reallized in order for the
may timeout, so you should try back later when dot from the timers available, a gray dot means automation to execute, click next and choose the
you get a better internet connection. that that timer for the selected day is empty. If red action that you want to happen when executing
5-If all the above fails, you can try rebooting the that means that the timer is already programmed Figure9 the automation. If you wish that the action will be
board and retrying, also you can reconfigure the and by selecting it you will override it once clicking delayed or will execute for a specific duration then
board and retry and make sure you remember all appply. use Delay and Duration buttons and enter the
parameters you enter especially those you will 4-Select the hours and minutes using the arrows period in seconds, then click Apply
need to pair the board at the top of the configuring then click apply. Schedule : Schedule the action ON or OFF. The action can be performed on another paired
page. 5- If you want to delete a timer that is already Delay : Delay the action ON or OFF in seconds board but that board has to be connected to the
- Programming timers: programmed, then click its red dot and then click Duration : Turn ON for the specified duration in same access point.
Each output in the board supports 5 ON timers delete. seconds - Groups and scenes:
daily, and 5 OFF timers daily meaning each output See Figure8 Groups : If you wish to assign some accessories to
can be scheduled to switch ON 5x7 times in a week a group and will be able to act on them with a
Page9 Page10 Page11 Page12

single click then click on Groups/Scenes button at - Wiring diagrams for different accessories : Notes about the previous wiring diagram : Automation2:If OUT3 is ON then OUT2 will turn
the bottom of the main screen and click on create L 1-The maximum load limit for the output relays is OFF
a new Group button then choose which 220V
250v AC at 10 amps or 30 VDC at 10 amps, so We can add 2 other automations to switch OFF the
accessories you wish to add to the group. After
N when driving loads above or near these limits we
relays after a specific delay like 30 sec to make
sure they don’t stay ON while the blind reached its
creating the group you can switch ON or OFF all its use contactors to protect the board as shown in limit.
accessories with a single click. Accessories from 16A 16A 10A the diagram when driving outlets and Blind - Wiring diagrams for detectors:
Circuit
different boards can be added to the same group. motors. There are two types of detectors that can be
Breakers
Scenes : A scene is a number of actions that can be 2-The input switches type is recommanded to be interfaced with 4CR4S boards.
executed with a single click or can be scheduled to push buttons but other types of switches can be Type1 : Analogue output detectors.
be executed at a specific time . To create a new used and the correct type must be entered during Type2 : Contact (Digital) output detectors
scene click on Scenes=>Create a new Scene and board configuration. L
Type2 220vAC
choose the accessories and the specific action for Modular 3-When driving Blind motors we use 2 relay
N
each accessory that you want it to perform when Contactors >16A outputs, each relay controls one direction with the
executing the scene, then click Add Scene, then second relay power comming from the first relay
this scene will be created and by clicking it it will NC output as to never actuate both motor Type1
be executed, you can schedule it then by clicking directions at the same time, also in order for this
Outlet Output
the clock icon on the scene. Blinds Motor setup to work, 2 automations must be >9V
programmed which are for our example where (AC/DC)
You can edit the scene or delete it later if you wish OUT2 and OUT3 are controlling the motor :
by clicking the edit icon on the scene. Automation1:If OUT2 is ON then OUT3 will turn You can connect an accessory in the corresponding
OFF output so you can control it by the detector.
Page13 Page14 Page15 Page16