Double Empty Container Handler TROUBLESHOOTING 6.6 Machine Error Codes 6.6.1 Machine Error Codes Table 6-15 No. Name Possible Causes | Suggested Actions Reference 1, Lower the traveling The traveling speed. Loaded Code 01 | orn ag Magen above ‘q_ | 2 Lower the load height, - Pe limit ety speed | 3, Decrease the forward tilting angle of mast. 1. Check whether the radiator temperature Gearbox control switch, driving temperature is too | motor and the radiator Code 02 | GearboxTemp_H | high, checked to _ | fin are dirty : be higher than —_| 2. Check whether the 120°C. voltage-distributing circuit of resistor is normal 4. Check whether the sensor connector is, Hydraulic oi normal. temperature is too | 2. Check whether the Code 03 | Hyd_OilTemp_H | high, checked to | sensors effective. - be higher than 65 | 3. Check the radiator or °C. the temperature control switch on it,Check if the radiator fin is dirty. 4.Check if the filter is too dirty or clogged. The signal of oil- | Replace or clean it if Code 04 | Oilwater_Alarm | water separatoris | necessary. - abnormal. 2, Check the switch ‘components with universal meter. The pressure Check if the parking oil- code 05 | ACC.PL_Alarm | Switch of way pressure and circuit . aia accumulator of parking valve are functions. normal The signal of 1. See “Coolant Code 06 | Engine_coolant_L | o-lant level 1, Check the coolant level, checking switch is level. and topping up’ abnormal. on page 5-54 @sany ‘Safety, Operation and Maintenance Manual-June 2019 661TROUBLESHOOTING Double Empty Container Handler Table 6-15 (continue) No. Name Possible Causes Suggested Actions Reference 2. Check the switch components with universal meter. 3. Check if the switch is too dirty. 4. Check if the wire-out of switch is. disconnected, Code 07 HYD_FJ_Alarm The signal of hydraulic oil filter is abnormal. 4. Check ifthe filter is too dirty or clogged Replace of clean itif necessary. 2. Check the switch componenis with universal meter. 1. See “Air filter element, changing" on page 5-115 Code 08 Brake_FJ_Alarm The signal of brake oil filter is abnormal, 1, Check ifthe filter is too dirty or clogged. Replace or clean itif necessary. 2. Check the switch components with universal meter. 1, See "Brake oil filter, changing” on page 5-121 Code 09 Sensor_Error The signal of sensors abnormal 1, Check the function of sensor. 2. Check ifthe wires are loose. 3. Check the power supply. Code 10 FueLevel_L The fuel level is lower than SOL. 1,Check the oil level of tank. 2.Check the sensor and circuit. 1, see “Fuel level, checking” on page 4-9 Code 11 GearboxPres sure_L The pressure is lower than 16 bar. 1. Dismantle the sensor to see if itis blocked 2. Check the function of sensor. 3. Check the disconnection alarm of sensor. Code 12 Engine_Tem_H The water temperature of 1. Check ifthe engine radiator is dirty. If yes, lean it, 1.See “Radiator, cleaning" on page 5-112 6-62 ‘Safety, Operation and Maintenance Manual-June 2019 @sanyDouble Empty Container Handler TROUBLESHOOTING Table 6-15 _ (continue) No. Name Possible Causes Suggested Actions Reference engine is above 103°C. 2. Check the water level and pipe of tank, 3. Check the fan and belt 2. see “Coolant level, checking” on page 4-8 3,See “Radiator fan, checking” on page 5-57 Oil pressure of 1, Check ifthe oil is refilled during maintenance. 1.See “Oil level, i hecki Code 13 Engine_OilPress__ engine oil is lower 2. Check if the filter is checking ska L then 68 ipa changed at regular topping up” on intervals. page 5-39 3. Check the oil sensor and circuit. 1. Check the working Battery vot condition of generator. Code 14 | Battery_voltage_L | Patery voltage 'S | 2. Check if there is - lower than 23V. enough power for battery. Use the safety | Check if the safety Code 15 | Safe_bypass bypass. bypass is functioning, ‘Spreader Check the working LockU: Code 16 | Aone Hnlock_ proximity switch is | condition of spreader 5 “ abnormal. proximity switch. Load tai 1. Check if the load ripe eM oe percentage is too large. Code 17 | Load_Over_90% th above 90% of | > Check if the heavy . 'e maximum pressure sensor is load. working normally. 1. Check if the load The lifting weight | percentage is too large. Code 18 | Over_Load is above the max. | 2. Check if the heavy - load. pressure sensor is working normally. 1.Check if the GPS. No receiving of GPS internal power line is connected Code 19 | SYMT_CanFault for ke well. as rene jong 2. Check the signal of GPS 663 @sany ‘Safety, Operation and Maintenance Manual-June 2019TROUBLESHOOTING Double Empty Container Handler Table 6-15 (continue) No. Name Possible Causes | Suggested Actions | Reference Noreceiving of | check the working CAN_ERROR i If - Code 20 | CANE eee | condition of CAN bus long interval 1. The machine is locked Code 21 | GPs_LocKED | GPS locked remotely. : 2. No signal for a long e. 1, Check ifthe lifting height is too high Reach the critical Code 22 | Rollover timit_ conchae 2. Cheek if the lifting - eae 22 | Alarm overt speed is too fast. a 3. Check if the tilting angle is too large. oe Brake oll Check hydraulic, Code 23 | BKONTemp_ temperature is too | pressure and circuits of - Alarm high. parking valve, etc. 1. Check the function of Altimetry_Sensor_| Height sensoris | sensor. . Code 24 |e abnormal, 2. Check ifthe wires are loose. Engine preheating | Check ifthe engine Code 25 | WarmUp_Alarm | time is over20 | preheating system is seconds normal Turbocharger needs plenty lubrication after Unableto speed | the engine is started. It Code 26 | IdleSpeed Alarm | othe machine | is unable to speed up . the engine when the rotate speed is limited. Check ifthe ignition Engine_ Code 27 | Oe nein Engine preheating | switch is rotated to the - p ‘a preheating position. Code 28 | C28"Box Error Transmission | Check the transmis 7 Alarm failure. SPN codes. 6-64 Safely, Operalion and Maintenance Manual-June 2079 @sany