Expt No 4

Sinhgad Technical Education Society’s
Sinhgad College of Engineering, Pune 41.

Department of Electronics & Telecommunication Semester –
I (2020 – 2021)
Subject: Electrical Circuits 204187 (ELC)
Tutorial No. 4
Instructions:
 Last date for submission of scanned copy of handwritten tutorial online on Google
classroom:30/11/2020
 Write /Solve all Tutorial on Ruled pages (if available)/Plain paper.

 Write Name, Division, Roll No at the beginning of the Tutorial.
Aim
To study the speed control of DC Motor by field resistance Control. Draw the graph between the armature current and motor speed by varying
the field resistance.
Theory
We know that the speed of shunt motor is given by:

N = (V-IaRa)/kФ
Where, Va is the voltage applied across the armature and φ is the flux per pole and is proportional to the field current If.. As explained earlier,
armature current Ia is decided by the mechanical load present on the shaft. Therefore, by varying Va and If we can vary n. For fixed supply
voltage and the motor connected as shunt we can vary Va by controlling an external resistance connected in series with the armature. If of
course can be varied by controlling external field resistance Rf connected with the field circuit.
Thus for shunt motor we have essentially two methods for controlling speed, namely by:
1. Varying armature resistance.
2. Varying field resistance.
Figure: Equivalent circuit for field control of DC motor

1.Speed control by varying field current:
In this method field circuit resistance is varied to control the speed of a d.c shunt motor. Let us rewrite the basic equation to understand the
method.
N = (V-IaRa)/kФ
If we vary I f, flux φ will change, hence speed will vary. To change If an external resistance is connected in series with the field windings. The
resistance is called the shunt field regulator the field coil produces rated flux when no external resistance is connected and rated voltage is
applied across field coil. It should be understood that we can only decrease flux from its rated value by adding external resistance. Thus the
speed of the motor will rise as we decrease the field current and speed control above the base speed will be achieved. Speed versus armature
current characteristic is shown.
Figure: Torque speed characteristics of DC motors
Procedure
1. Connect all dots in the following manner:

(a) A to K
(b) A to Y
(c) A to J
(d) B to P
(e) E to M
(f) F to D
(g) G to R
(h) H to I
(i) I to C
(j) C to H
(k) Q to L
Then Check the connections by clicking on Check Button.

(TAKE PRINTOUT OF CONNECTION DIAGRAM)
3. If it shows alert "Incorrect Corrections" then press reset button and make connection again.
4. If it shows alert"Correct Connections" then Turn On the MCB.
5. Then set the Voltmeter first with the help of the second slider.
6. Now,move the first slider to get corresponding values of Ammeter and Speedometer.
7. Press the "Add to table" button to insert the values in table.
8. After inserting values on table click on "Plot graph" to get your required graph.
CONCLUSION
(WRITE CONCLUSION HERE)
2. Speed Control of DC motor by Armature Resistance Control
Aim
To study the speed control of D.C. Shunt motor by armature control method. Draw the graph between armature voltage and
motor speed by varring the armature voltage.
Theory
Introduction
We know that the speed of shunt motor is given by:
N = (V-IaRa)/kФ
Where, Va is the voltage applied across the armature and φ is the flux per pole and is proportional to the field current If.. As
explained earlier, armature current Ia is decided by the mechanical load present on the shaft. Therefore, by varying Va and If we can
vary n. For fixed supply voltage and the motor connected as shunt we can vary Va by controlling an external resistance connected
in series with the armature. If of course can be varied by controlling external field resistance Rf connected with the field circuit.
Thus forshunt motor we have essentially two methods for controlling speed, namely by:
1. Varying armature resistance.

2. Varying field resistance.
Figure: Equivalent circuit for armature control of DC motor
Speed control by varying armature resistance

In this method a variable series resistor Rext is put in the armature circuit. In this case the field is directly connected across the
supply and therefore the flux ɸ is not affected by variation of Rext. in this case the current and hence the flux are affected by the
variation of the armature circuit resistance. The voltage drop in Rext reduces the voltage applied to the armature and therefore the
speed is reducing.
The slope of the n vs. Iaor n vs. Te characteristic can be modified by deliberately connecting external resistance rext in the armature
circuit. One can get a family of speed vs. armature curves for various values of rext. From these characteristics it can be explained
how speed control is achieved. Let us assume that the load torque TL is constant and field current is also kept constant.
Therefore, since steady state operation demands Te = TL, Te = kφ too will remain constant; which means Ia will not change.
Suppose rext = 0, then at rated load torque, operating point will be at C and motor speed will be n. If additional resistance rext1 is
introduced in the armature circuit, new steady state operating speed will be n1 corresponding to the operating point D. In this way
one can get a speed of n2 corresponding to the operating point E, when rext2 is introduced in the armature circuit. This same load
torque is supplied at various speed. Variation of the speed is smooth and speed will decrease smoothly if rext is increased.
Obviously, this method is suitable for controlling speed below the base speed and for supplying constant rated load torque which
ensures rated armature current always. Although, this method provides smooth wide range speed control (from base speed down
to zero speed), has a serious draw back since energy loss takes place in the external resistance rext reducing the efficiency of the
motor.
Figure: Armature current speed characteristics of DC motors
Procedure
The following procedure is to be followed for the simulation:
1. Make the proper Connections as per the Instructions. a) first of all connect the + (positive) terminal of MCB to the
(-)negative terminal of Voltmeter(V) and to the motor's A2 and F2 Port respectively .
b) Connect - (negative) terminal of MCB to the L port of the Starter.
c) Connect The F port of the starter to the positive (+) terminal of the Ammeter(A).
d) Connect the A port of starter to the positive (+) terminal of the Armature Resistance .
e) Connect the positive(+) terminal of the voltmeter(V) to the negative(-) terminal of the Armature Resistance and to the
motor's A1 Port respectively.
f) Connect Ammeter's negative(-) terminal to the positive(+) terminal of the Field Resistance.
g) Connect Negative (-) Terminal of the Field Resistance to the Port F1 of the Motor.
h) Connect Port A1 of the Motor to the Negative (-) terminal of the Armature Resistance.
(TAKE PRINTOUT OF CONNECTION DIAGRAM)
2. Tap on the MCB to turn on the circuit.
3. Move slider second to get variations over the voltmeter readings.
4. Then tap on Add to Table Button to values to table.
5. Repeat steps 3 & 4 to add more values in table
6. After getting 6 or more rows on table then click on Create Graph button to make a respective graph regarding the values
in above table.
7. In order to print the page click on Print button .
CONCLUSION
(WRITE CONCLUSION HERE)

Expt No 4

Uploaded by

Copyright:

Available Formats

Expt No 4

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Expt No 4

Uploaded by

Copyright:

Available Formats

Sinhgad Technical Education Society’s

Sinhgad College of Engineering, Pune 41.

 Write /Solve all Tutorial on Ruled pages (if available)/Plain paper.

We know that the speed of shunt motor is given by:

Figure: Equivalent circuit for field control of DC motor

Figure: Torque speed characteristics of DC motors

1. Connect all dots in the following manner:

Then Check the connections by clicking on Check Button.

(WRITE CONCLUSION HERE)

2. Speed Control of DC motor by Armature Resistance Control

1. Varying armature resistance.

Figure: Equivalent circuit for armature control of DC motor

Speed control by varying armature resistance

Figure: Armature current speed characteristics of DC motors

The following procedure is to be followed for the simulation:

(WRITE CONCLUSION HERE)

You might also like