Standard Part STPE600

Rev AH
Projection Weld Nuts - Metric Fine and
Page 1 of 17
Coarse Thread, Preferred & Non-Preferred
1. SCOPE

There is no National or International Standard on six (6) projection weld nuts as covered by this standard.
The specifications are based upon local manufacturer and user requirements. Commercial availability of
these six (6) projection weld nuts is generally restricted to North America.

The specification for three (3) projection weld nuts is based on German Institute of Standardization DIN
929. Weld nuts to DIN 929 do not meet proof load requirements calculated for full loadability and therefore
they are restricted to applications where local availability and existing tooling and equipment mandates
their use.

When a standard is referenced in a drawing or specification, it is understood that the reference is to the
latest revision of the standard, unless stated otherwise.

2. PART DESCRIPTION

Typical part description for BOM’s and CAD drawings entered by Standards.

NUT, WELD M8 STD LONG PLN

For cross-reference listing of company part numbers, go to CNH Catalogue.

3. RELATED DOCUMENTS

3.1 REFERENCE STANDARDS

CNH STPA020—Fastener Finishes and Material Specifications

CNH MAT0310—Zinc Plating
FIAT 52605/02—Property classes of special service fasteners
SAE J122—Surface Discontinuities on Nuts
ANSI B18.16.1M—Mech. and Perf. Requirements For Prevailing-Torque Type Steel Metric Hex Nuts
DIN 928—Square weld nuts
DIN 929—Hexagon weld nuts
FIAT 10143—Embossed Hexagon Nuts for Projection Welding
FIAT 10143/02—Hexagon High Nuts for Projection Welding-Severe Applications
FIAT 10143/22— Square Nuts w/ Embossments for Projection Welding
FIAT 10143/23— Square Nuts w/ Embossments for Projection Welding

3.2 REPLACED STANDARDS

Case EM-070—Weld Nuts Metric Projection Preferred

Case EM-072—Weld Nuts Metric Prevailing Torque Projection Preferred
NH ES10.04—Square Weld Nuts

AUTHOR APPROVED BY ECO PART NUMBER

A KHAN 13NOV15 P TUPEK 13NOV15 35229079 87366975

THE INFORMATION HEREON IS THE CONFIDENTIAL AND PROPRIETARY PROPERTY OF CNH INDUSTRIAL AND/OR
ITS SUBSIDIARIES OR DIVISIONS. ANY USE, EXCEPT THAT FOR WHICH IT MAY BE LOANED, IS PROHIBITED.
UNCONTROLLED COPY When Printed
 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 2 of 17
Coarse Thread, Preferred & Non-Preferred

4. REQUIREMENTS

4.1 MATERIAL

Material as designated by part number per CNH STPA020. Six-projection weld nuts shall be steel, 1010,
1015, 1018 or 1117.
Three-projection weld nuts shall be steel with a maximum carbon content of 0.25% and a maximum sulfur
content of 0.13% that meets the following proof loads:

Size Proof Load in N

M3 3,800
M4 6,800
M5 11,000
M6 15,500
M8 28,300
M10 44,800
M12 65,300
M14 89,700
M16 123,000

Materials specified as R40SD, R80SD or 8SD will conform to Fiat material standard 52605/02 ‘Property
classes of special service fasteners’.

4.2 PREFERRED PARTS POLICY

Preferred parts are so designated to reduce variety of parts and assure maximum availability and cost
savings:

Sizes: 6 Projection Regular Series - M6, 8, 10

6 Projection Heavy Series - M10, 12, 16

4.3 MECHANICAL DIMENSIONS

All dimensions in this standard are in millimetres. All unspecified detail must conform to standards listed
above.

4.4 SURFACE DISCONTINUITIES

All products under this specification shall be free from burrs, seams, laps, loose scale, irregular surfaces
and any defects affecting their serviceability.

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 3 of 17
Coarse Thread, Preferred & Non-Preferred

4.5 THREADS

Threads shall be standard (coarse) pitch ISO Metric Screw Threads, tolerance class 6G for 3-projection
nuts per DIN 929 and class 6H for 6-projection nuts.

4.6 MARKING

Six-projection weld nuts shall be identified as metric by the symbol “M” or a numerical “9" indented on the
top surface of the nut.

4.7 PREVAILING TORQUE

When specified, prevailing torque weld nuts shall be all metal, one-piece construction. The prevailing
torque characteristics are developed by controlled distortion of the nut thread and/or body on the upper
portion or dome of the nut and are to meet the prevailing torque requirements specified in ANSI
B18.16.1M.

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 4 of 17
Coarse Thread, Preferred & Non-Preferred
Hex Piloted Projection Weld Nuts

Table 1: Hex 6 Projections, Regular Series - Short Pilot, Preferred

Nominal Size M5* M6 M8 M10 M12*

Pitch, Nominal 0.8 1 1.25 1.5 1.75
max 11 13 15 18 21
A Width Across Flats
min 10.7 12.7 14.7 17.7 20.6
B Width Across Corners min 12.12 14.38 16.64 20.03 23.35
max 4.8 5.6 7.1 8.2 9.9
C Nut Thickness
min 4.4 5.1 6.6 7.7 9.4
max 7.65 9.1 11.1 13.6 16.1
D Pilot Diameter
min 7.35 8.8 10.8 13.3 15.8
E Chamfer Diameter min 5.8 6.8 8.8 11 13
max 1.03 1.13 1.13 1.29 1.39
F Pilot Height
min 0.77 0.87 0.87 1.03 1.13
max 0.47 0.52 0.52 0.63 0.73
G Projection Height
min 0.31 0.36 0.36 0.47 0.57
H Projection Width min 2.64 3.17 3.69 4.49 5.29
J Projection Locating Height ref 0.3 0.35 0.35 0.4 0.4
R Projection Radius nom 2.87 3.54 4.64 5.4 6.25
max 1.5 1.6 1.6 1.9 1.9
Plate Thickness
min 1 1.1 1.1 1.3 1.4
Hole Size in Plate ±0.25 8 9.5 11.5 14 16.5
Part Number 87301293 86639237 86639238 86639239 86639641

* Non- Preferred

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 5 of 17
Coarse Thread, Preferred & Non-Preferred
Hex Piloted Projection Weld Nuts

Table 2: Hex 6 Projections, Heavy Series - Short Pilot, Preferred

Nominal Size M8* M10 M12 M14* M16

Pitch, Nominal 1.25 1.5 1.75 2 2
max 15 18 21 24 26
A Width Across Flats
min 14.7 17.7 20.6 23.6 24.9
B Width Across Corners min 16.6 20 23.3 26.7 29.1
max 9.3 12.2 14.3 16.5 19
C Nut Thickness
min 8.8 11.7 13.8 15.9 18.4
max 11.1 13.4 16.1 19 20.5
D Pilot Diameter
min 10.8 13.1 15.8 18.7 20.2
E Chamfer Diameter min 8.6 10.7 12.8 15 17
max 0.83 1.13 1.33 1.33 1.33
F Pilot Height
min 0.57 0.87 1.07 1.07 1.07
max 0.53 0.63 0.73 0.73 0.73
G Projection Height
min 0.37 0.47 0.57 0.57 0.57
H Projection Width min 3.69 4.49 5.29 6.09 6.61
J Projection Locating Height ref 0.25 0.45 0.55 0.55 0.55
max 10.5 12.8 15.3 18.3 19.5
K Counterbore Diameter
min 10.2 12.5 15 18 19.2
max 1.5 1.5 1.5 1.5 1.5
M Counterbore Depth
min 1.25 1.25 1.25 1.25 1.25
R nom 4.54 5.4 6.25 8.09 9.41
max 1.8 1.8 2.2 2.2 2.2
Plate Thickness
min 0.7 1 1.2 1.2 1.2
Hole Size in Plate +0.1/-0.2 11.4 13.7 16.4 19.4 20.9
Part Number 86639240 -- -- -- --

* Non- Preferred

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 6 of 17
Coarse Thread, Preferred & Non-Preferred
Hex Piloted Projection Weld Nuts

Table 3a: Hex 6 Projections, Heavy Series - Long Pilot, Preferred

Nominal Size M6* M8* M10 M12 M14* M16

Pitch, Nominal 1 1.25 1.5 1.75 2 2
max 13 15 18 21 24 26
A Width Across Flats
min 12.73 14.7 17.7 20.6 23.6 24.9
B Width Across Corners min 14.38 16.6 20 23.3 26.7 29.1
max 8 9.3 12.2 14.3 16.5 19
C Nut Thickness
min 7.5 8.8 11.7 13.8 15.9 18.4
max 9 11.1 13.4 16.1 19 20.5
D Pilot Diameter
min 8.7 10.8 13.1 15.8 18.7 20.2
E Chamfer Diameter min 6.6 8.6 10.7 12.8 15 17
max 1.93 1.93 1.93 1.93 1.93 1.93
F Pilot Height
min 1.67 1.67 1.67 1.67 1.67 1.67
max 1.08 1.08 1.08 1.08 1.08 1.08
G Projection Height
min 0.92 0.92 0.92 0.92 0.92 0.92
H Projection Width min 3.17 3.69 4.49 5.29 6.09 6.61
Projection Locating
J ref 0.8 0.8 0.8 0.8 0.8 0.8
Height
max 8.4 10.5 12.8 15.3 18.3 19.5
K Counterbore Diameter
min 8.15 10.2 12.5 15 18 19.2
max 1.5 1.5 1.5 1.5 1.5 1.5
M Counterbore Depth
min 1.25 1.25 1.25 1.25 1.25 1.25
R nom 1.96 2.44 3.31 4.34 5.53 6.38
max 6.5 6.5 6.5 6.5 6.5 6.5
Plate Thickness
min 1.8 1.8 1.8 1.8 1.8 1.8
Hole Size in Plate +0.1/-0.2 9.3 11.4 13.7 16.4 19.4 20.9
Part Number 76088686 87026741 86978773 87017612 -- 87020955
47458649# 82879448#
* Non- Preferred #Prevailing Torque Nut

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 7 of 17
Coarse Thread, Preferred & Non-Preferred
Hex Piloted Projection Weld Nuts

Table 3b: Hex 6 Projections, Heavy Series - Long Pilot, Non-Preferred

Material: R80SD (10.9) and Finish: PFL
Nominal Size M6 M8 M10 M12 M14 M16
Pitch, Nominal 1 1.25 1.5 1.75 2 2
max 13 15 18 21 24 26
A Width Across Flats
min 12.73 14.7 17.7 20.6 23.6 24.9
B Width Across Corners min 14.38 16.6 20 23.3 26.7 29.1
max 8 9.3 12.2 14.3 16.5 19
C Nut Thickness
min 7.5 8.8 11.7 13.8 15.9 18.4
max 9 11.1 13.4 16.1 19 20.5
D Pilot Diameter
min 8.7 10.8 13.1 15.8 18.7 20.2
E Chamfer Diameter min 6.6 8.6 10.7 12.8 15 17
max 1.93 1.93 1.93 1.93 1.93 1.93
F Pilot Height
min 1.67 1.67 1.67 1.67 1.67 1.67
max 1.08 1.08 1.08 1.08 1.08 1.08
G Projection Height
min 0.92 0.92 0.92 0.92 0.92 0.92
H Projection Width min 3.17 3.69 4.49 5.29 6.09 6.61
Projection Locating
J ref 0.8 0.8 0.8 0.8 0.8 0.8
Height
max 8.4 10.5 12.8 15.3 18.3 19.5
K Counterbore Diameter
min 8.15 10.2 12.5 15 18 19.2
max 1.5 1.5 1.5 1.5 1.5 1.5
M Counterbore Depth
min 1.25 1.25 1.25 1.25 1.25 1.25
R nom 1.96 2.44 3.31 4.34 5.53 6.38
max 6.5 6.5 6.5 6.5 6.5 6.5
Plate Thickness
min 1.8 1.8 1.8 1.8 1.8 1.8
Hole Size in Plate +0.1/-0.2 9.3 11.4 13.7 16.4 19.4 20.9
Part Number 47910914

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 8 of 17
Coarse Thread, Preferred & Non-Preferred

Hex Piloted Projection Weld Nuts

Table 4: Hex 3 Projections, Preferred

Nominal Size M4 M5 M6 M8
Pitch, Nominal 0.7 0.8 1 1.25
A Width Across Flats max 9 10 11 14
B Width Across Corners min 9.83 10.95 12.02 15.38
C Nut Thickness max 3.5 4 5 6.5
max 5.97 6.96 7.96 10.45
D Pilot Diameter
min 5.895 6.87 7.87 10.34
max 0.65 0.7 0.75 0.9
F Pilot Height
min 0.55 0.6 0.6 0.75
max 0.35 0.4 0.4 0.5
G Projection Height
min 0.25 0.3 0.3 0.35
max 3 3.5 4 4.5
Plate Thickness
min 0.75 0.88 0.88 1
Hole Size in Plate +0.1/-0.2 6.2 7.2 8.2 10.7
Part Number 86639953 86639233 86639234 86625084

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 9 of 17
Coarse Thread, Preferred & Non-Preferred
Hex Piloted Projection Weld Nuts

Table 4: Hex 3 Projections, Preferred (Continued)

Nominal Size M10 M12 M14* M16

Pitch, Nominal 1.5 1.75 2 2
A Width Across Flats max 17 19 22 24
B Width Across Corners min 18.74 20.91 24.27 26.51
C Nut Thickness max 8 10 11 13
max 12.45 14.75 16.75 18.735
D Pilot Diameter
min 12.34 14.64 16.64 18.605
max 1.15 1.4 1.8 1.8
F Pilot Height
min 0.95 1.2 1.6 1.6
max 0.65 0.8 1 1
G Projection Height
min 0.5 0.6 0.8 0.8
max 5 5 6 6
Plate Thickness
min 1.25 1.5 2 2
Hole Size in Plate +0.1/-0.2 12.7 15.0 17.0 19.0
Part Number 86013959 86619782 84218881 86619383

* Non- Preferred

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 10 of 17
Coarse Thread, Preferred & Non-Preferred

Table 5: Hex Weld Nut, Non-Preferred

C A G D
Width
Nominal Nut Projection Pilot Part
Pitch Projections Across Material
Diameter Thickness Height Diameter Number
Flats
6 1 6 3 13 1 8
6 1 6 3 13 1.4 8
6 1 6 3 13 1.4 8
6 1 8.5 3 13 1.4 8 14100010
8 1.25 7 3 17 1.4 11
8 1.25 7 3 17 1.4 11
8 1.25 10 3 17 1.4 11 14100110
8 1.25 7.5 3 16 1 11
10 1 8 3 17 1.15 12.5 100086
10 1.25 12 3 19 1.4 13 14100210
10 1.5 8 3 17 1.15 12.5 62035
10 1.5 8 3 17 1.15 12.5 SST 84408059
12 1.25 14.5 3 22 1.4 16 14100310

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 11 of 17
Coarse Thread, Preferred & Non-Preferred
Table 6: Dimensions of Embossed Hexagon Nuts for Projection Welding (Style A)
Fiat 10143

D (h11) D2 D1 f h (h13) s (h13) e

D(h6) m n 0
Nom. Tol. Nom. Tol. Nom. Tol. Nom. Tol. Min.
-0.5
M4 8 8 7 9.8 4 4.8 5.5 12 13.25
0 0
M5 8 8 7 +0.150 9.8 4 5.8 5.5 12 13.25
-0.090 -0.180
M6 8 8 7 0 10 4.5 6.8 6.0 13 0 14.38
M8 11 11 10 13 5 9 7.5 16 -0.270 17.77
0 0
-0.110 +0.180 -0.220
M10x1.25 13 13 12 15 6 11 8.5 17 18.90
0

Table 7: Embossed Hexagon Nuts for Projection Welding (Style A)

Diameter Projections Material Finish Part Number
M4 3 8SD PLN 14098410
M5 3 R40SD PLN 14098000
M5 3 8SD PLN 14098010
M6 3 R40SD PLN 14096900
M8 3 R40SD PLN 14098200
M8 3 8SD PLN 14098210
M10X1.25 3 8SD PLN 14098310
M10 3 8SD PLN 14098610

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 12 of 17
Coarse Thread, Preferred & Non-Preferred
Table 8: Dimensions of Embossed Hexagon Nuts for Projection Welding (Part 1 / Style B)
Fiat 10143

d (h11) D2 D1 f h (h13) s (h13) e

D(h6) m n 0
Nom. Tol. Nom. Tol. Nom. Tol. Nom. Tol. Min.
-0.5
M4 8 8 7 10 2.2 4.8 6 13 14.38
0 0
M5 8 8 7 +0.150 10 2.2 5.8 6 13 0 14.38
-0.090 -0.180
M6 8 8 7 0 10 2.2 6.8 6 13 -0.270 14.38
M8 11 11 10 14 3 9 7 17 18.90
0
M10x1.25 13 13 12 16 3 11 8 19 21.10
0 -0.220
M12x1.25 15.5 15.5 14 +0.180 18.5 3.5 13 10 22 0 24.49
-0.110
0 0 -0.270
M14x1.5 18 18 16 21 3.5 15 12 24 26.75
-0.270

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 13 of 17
Coarse Thread, Preferred & Non-Preferred
Table 9: Embossed Hexagon Nuts for Projection Welding (Part 1 / Style B)

Diameter Projections Material Finish Part Number

M4 3 R40SD PLN 14077900
M5 3 R40SD PLN 14078000
M5 3 8SD PLN 14078010
M5 3 8SD PFL 14078013
M6 3 8SD PLN 14098710
M6 3 R40SD PLN 14098700
M6 3 8SD PFL 14098713
M8 3 8SD PLN 14098810
M8 3 8SD PFL 14098813
M8 3 R40SD PLN 14098800
M10x1.25 3 R40SD PLN 14098900
M10x1.25 3 8SD PFL 14098913
M12x1.25 3 R40SD PLN 14096800
M12x1.25 3 8SD PLN 14096810
M14x1.5 3 R40SD PLN 47727180

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 14 of 17
Coarse Thread, Preferred & Non-Preferred
Table 10: Dimensions of Embossed Hexagon Nuts for Projection Welding (Part 2 / Style B)

d (h11) D2 D1 f h (h13) s (h13) e

D(h6) m n 0
Nom. Tol. Nom. Tol. Nom. Tol. Nom. Tol. Min.
-0.5
0 +0.180 0 0
M10x1.5 13 13 12 16 3 11 11 19 21.10
-0.110 0 -0.270 -0.270

Diameter Projections Material Finish Part Number

M10x1.5 3 8 SD PFL 47661213
M10x1.5 3 R80SD PFL 47732805

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 15 of 17
Coarse Thread, Preferred & Non-Preferred
Square Weld Nut, Non-Preferred (DIN 928)

Table 11: Square Weld Nut, Non-Preferred (DIN 928)

D1 H S C
Nut Width Projection
Nominal Part
Pitch Thickness Projections Across Height
Diameter Number
(h14) Flats (h14) (+/- 0.1)
4 0.7 3.5 4 7 0.6 334480
5 0.8 4.2 4 9 0.8 383995
6 1 5 4 10 0.8 9706761
8 1.25 6.5 4 14 1 86629545
10 1.25 8 4 17 1.2 47670152
10 1.5 8 4 17 1.2 100076
12 1.75 9.5 4 19 1.4 331290
16 2 13 4 24 1.6 379329

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 16 of 17
Coarse Thread, Preferred & Non-Preferred
Fiat 10143/22 Square Nut With Embossments for Projection Welding

Table 12: Square Weld Nut, Non-Preferred (Fiat 10143/22)

d2 h2
d D2 D1 h s
D +0.3 m h1 0 R R1
Part Number (h11) * (H13) (h14) max Matl Finish
0 -0.15
14050000 M4 6 2 6 5 10.5 5.5 1 0.5 11.6 1 1.25 R40SD PLN
47912137 M5 7 2 7 6 10.5 5.5 1 0.5 11.6 1 1.25 R40SD PLN
14050200 M6 8 2 8 7 10.5 5.5 1 0.5 11.6 1 1.25 R40SD PLN
14050300 M8 10.5 3 10.5 9.5 17 8.5 1.2 0.7 17.9 1.5 1.95 R40SD PLN
* For hole diameter tolerance see Fiat Std. 01328.

UNCONTROLLED COPY When Printed

 Standard Part STPE600
Rev AH
Projection Weld Nuts - Metric Fine and
Page 17 of 17
Coarse Thread, Preferred & Non-Preferred
Fiat 10143/23 Square Nut With Embossments for welding

Table 13: Square Weld Nut, Non-Preferred (Fiat 10143/23)

d3 m h1
d1 d2 D1 h2 h
Part Number D +0.1 +0.5 +0.25 R Matl Finish
+/-0.2 +/-0.2 * +/-0.1 +/-0.25
-0.2 0 -0.1
14061310 M10X1.25 11 13 13 13.2 8.8 1.5 1 17 10 8 SD PLN
* For hole diameter tolerance see Fiat Std. 01328.

UNCONTROLLED COPY When Printed