Deh-X66 6650 6680

ORDER NO.
CRT5368
DEH-X66BT/XNUC
CD RDS RECEIVER
DEH-X66BT /XNUC
DEH-X6600BT /XNUC
DEH-X6650BT /XNGS
DEH-X6650BT /XNCS
DEH-X6690BT /XNID
This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-3287 CRT4759 S11.6STD CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2013
K-ZZZ JULY 2013 Printed in Japan
1 2 3 4
SAFETY INFORMATION
CAUTION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B Where in a manufacturer’s service documentation, for example in circuit diagrams or lists

of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
- Safety Precautions for those who Service this Unit.

When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
C
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
D 60825-1:2007.
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
E A specially instructed person should do servicing operation of the apparatus.
Laser diode characteristics

Wave length : 785 nm to 814 nm
Maximum output : 1 190 µW(Emitting period : unlimited)
Additional Laser Caution

Transistors Q101 in PCB drive the laser diodes.
F
When Q101 is shorted between their terminals, the laser diodes will radiate beam.
If the top cover is removed with no disc loaded while such short-circuit is continued,
the naked eyes may be exposed to the laser beam.
DEH-X66BT/XNUC
2
1 2 3 4
5 6 7 8
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacturer.
Discord used batteries according to the manufacturer's instructions.
DEH-X66BT/XNUC
5 6 7 8
3
1 2 3 4
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS ............................................................................................................................................ 6
2.1 SPECIFICATIONS ..................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 9
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 10
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 10
3.2 PCB LOCATIONS .................................................................................................................................... 10
3.3 JIGS LIST .................................................................................................................................................11
3.4 CLEANING................................................................................................................................................11
4. BLOCK DIAGRAM.......................................................................................................................................... 12
5. DIAGNOSIS.................................................................................................................................................... 14
B 5.1 OPERATIONAL FLOWCHART ................................................................................................................ 14
5.2 ERROR CODE LIST ................................................................................................................................ 15
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 19
6. SERVICE MODE ............................................................................................................................................ 20
6.1 DISPLAY TEST MODE 1 ......................................................................................................................... 20
6.2 DISPLAY TEST MODE 2 ......................................................................................................................... 21
6.3 SOFTWARE VERSION UP METHOD ..................................................................................................... 22
6.4 CD TEST MODE ...................................................................................................................................... 23
7. DISASSEMBLY .............................................................................................................................................. 24
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 30
8.1 CD ADJUSTMENT................................................................................................................................... 30
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 31
C
8.3 PCL OUTPUT CONFIRMATION.............................................................................................................. 33
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 33
9.1 PACKING ................................................................................................................................................. 34
9.2 EXTERIOR............................................................................................................................................... 36
9.3 CD MECHANISM MODULE..................................................................................................................... 38
10. SCHEMATIC DIAGRAM............................................................................................................................... 40
10.1 TUNER AMP UNIT (GUIDE PAGE) ....................................................................................................... 40
10.2 KEYBOARD UNIT.................................................................................................................................. 46
10.3 CD CORE UNIT (S11.6VA) .................................................................................................................... 48
10.4 BT UNIT ................................................................................................................................................. 50
10.5 WAVEFORMS ........................................................................................................................................ 52
D 11. PCB CONNECTION DIAGRAM.................................................................................................................... 54
11.1 TUNER AMP UNIT................................................................................................................................. 54
11.2 KEYBOARD UNIT .................................................................................................................................. 58
11.3 CD CORE UNIT (S11.6VA) .................................................................................................................... 60
11.4 BT UNIT ................................................................................................................................................. 62
12. ELECTRICAL PARTS LIST .......................................................................................................................... 63
DEH-X66BT/XNUC
4
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
1. You should conform to the regulations governing the product (safety, radio and noise, and other
regulations), and should keep the safety during servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside the unit.
3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the grating.
5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by
electrostatic induction.
6. Notes about installation and pin number description of Power IC (IC301: PA2032A) B
The Power IC, PA2032A used on tha Tuner Amp Unit is a 25 pin IC.
The same PCB of the Tuner Amp Unit is used for other models that use a 27 pin IC, too.
So, the PCB has lands for a 27 pin IC.
When you replace the Power IC, install the Power IC onto 25 pins (2- 26 pin) located in the center of 27 pins for IC301.
Therefore, when you check the Power IC on the block diagram, the schematic diagram and the PCB connection
diagram, you have to pay attention as follows.
BLOCK DIAGRAM SCHEMATIC DIAGRAM

The pin number of left side is a number
12 (11)
No connection on the PCB (silk printing).
13 (12) 1 C
10 (9)
2
8 (7) 3
4
The pin number of right side (in the IC frame)
6 (5)
5 means the pin number of IC itself.
4 (3) 6
7
8
23 (22) 9
10
11
26 (25)
H-SW 12
13
2 (1) 14
OFF.DET
15
16
17
The pin number is a number on the PCB 18
19
(silk printing). 20
21
The number in parentheses means the 22 D
pin number of IC itself. 23
24
25
No connection
1.2 NOTES ON SOLDERING

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs E
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:

Parts numbers of lead-free solder:
GYP1006 1.0 in dia. F
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
DEH-X66BT/XNUC
5 6 7 8
5
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A DEH-X66BT/XNUC, DEH-X6600BT/XNUC
General USB
Power source ...................14.4 V DC (10.8 V to 15.1 V al- USB standard specification
lowable) ................................... USB 2.0 full speed
Grounding system ............Negative type Maximum current supply
Maximum current consumption ................................... 1 A
..................................10.0 A USB Class ....................... MSC (Mass Storage Class)
Backup current.................. 4.0 mA or less File system....................... FAT12, FAT16, FAT32
Dimensions (W × H × D): MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
DIN WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
Chassis ............................ 178 mm × 50 mm × 165 mm audio)
(7 in. × 2 in. × 6-1/2 in.) (Windows Media Player)
Nose ................................ 188 mm × 58 mm × 15 mm WAV signal format ...........Linear PCM & MS ADPCM
B (7-3/8 in.× 2-1/4 in.× 5/8 in.) (Non-compressed)
D
Chassis ............................ 178 mm × 50 mm × 165 mm
(7 in.× 2 in.× 6-1/2 in.) FM tuner
Nose ................................ 170 mm × 46 mm × 15 mm Frequency range ..............87.9 MHz to 107.9 MHz
(6-3/4 in.× 1-3/4 in.× 5/8 in.) Usable sensitivity ............. 9 dBf (0.8 µV/75Ω, mono, S/N:
30 dB)
Weight ............................. 1 kg (2.2 lbs)
Signal-to-noise ratio ......... 72 dB (IHF-A network)
Audio
Maximum power output ... 50 W × 4
AM tuner
Frequency range .............. 530 kHz to 1 710 kHz
70 W × 1/2 Ω (for subwoofer)
Usable sensitivity ............. 25 µV (S/N: 20 dB)
Continuous power output
Signal-to-noise ratio ......... 62 dB (IHF-A network)
................................... 22 W × 4 (50 Hz to 15 000 Hz,
C
5 % THD, 4 Ω load, both chan-
nels driven) Bluetooth
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable) Version ............................Bluetooth 3.0 certified
Preout maximum output level Output power ................... +4 dBm Maximum
................................... 2.0 V (Power class 2)
Loudness contour ............ +10 dB (100 Hz), +6.5 dB
(10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer): CEA2006 Specifications
Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/
8 kHz
Equalization range ........... ±12 dB (2 dB step)
Subwoofer (mono):
Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/
D
125 Hz/160 Hz/200 Hz
Slope ...............................–12 dB/oct,–24 dB/oct Power output ................... 14 W RMS × 4 Channels (4 Ω
Gain ................................ +6 dB to –24 dB and 1 % THD+N)
Phase .............................. Normal/Reverse S/N ratio .......................... 91 dBA(reference: 1 W into
4 Ω)
CD player Note
System ............................Compact disc audio system Specifications and the design are subject to
Usable discs ....................Compact disc
modifications without notice.
Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)
Number of channels ........ 2 (stereo)
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
E audio)
(Windows Media Player)
WAV signal format ...........Linear PCM & MS ADPCM
(Non-compressed)
Securing the front panel

The front panel can be secured with the sup-
plied screw.
F
Screw
(BPZ20P060FTC) (UC)
(XXX7020) (Except UC)
DEH-X66BT/XNUC
6
1 2 3 4
5 6 7 8
DEH-X6650BT/XNGS A
General CD player
Rated power source .........14.4 V DC System ............................Compact disc audio system
(allowable voltage range: Usable discs ....................Compact disc
12.0 V to 14.4 V DC) Signal-to-noise ratio ......... 94 dB (1 kHz) (IEC-A network)
Grounding system ............Negative type Number of channels ........ 2 (stereo)
Maximum current consumption MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
..................................10.0 A WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
Backup current.................. 4.0 mA or less audio)
Dimensions (W × H × D): (Windows Media Player)
DIN WAV signal format ...........Linear PCM & MS ADPCM
Chassis ............................ 178 mm × 50 mm × 165 mm (Non-compressed)
Nose ................................ 188 mm × 58 mm × 15 mm
D B
USB
Chassis ............................ 178 mm × 50 mm × 165 mm
USB standard specification
Nose ................................ 170 mm × 46 mm × 15 mm
................................... USB 2.0 full speed
Weight ............................. 1 kg
Maximum current supply
................................... 1 A
Audio USB Class ....................... MSC (Mass Storage Class)
Maximum power output ... 50 W × 4 File system....................... FAT12, FAT16, FAT32
70 W × 1/2 Ω (for subwoofer) MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
Continuous power output WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
................................... 22 W × 4 (50 Hz to 15 000 Hz, audio)
5 % THD, 4 Ω load, both chan- (Windows Media Player)
nels driven) WAV signal format ........... Linear PCM & MS ADPCM
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable) (Non-compressed)
C
Preout maximum output level
................................... 2.0 V
FM tuner
Loudness contour ............ +10 dB (100 Hz), +6.5 dB
Frequency range ..............87.5 MHz to 108.0 MHz
(10 kHz) (volume: –30 dB)
Usable sensitivity ............. 9 dBf (0.8 µV/75 Ω, mono, S/N:
Equalizer (5-Band Graphic Equalizer):
30 dB)
Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/
Signal-to-noise ratio ......... 72 dB (IEC-A network)
8 kHz
Subwoofer (mono): MW tuner
Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/ Frequency range .............. 531 kHz to 1 602 kHz (9 kHz)
125 Hz/160 Hz/200 Hz 530 kHz to 1 640 kHz (10 kHz)
Slope ...............................–12 dB/oct, –24 dB/oct Usable sensitivity ............. 25 µV (S/N: 20 dB)
Gain ................................ +6 dB to –24 dB Signal-to-noise ratio ......... 62 dB (IEC-A network) D
Phase .............................. Normal/Reverse
SW tuner
Frequency range .............. 2 300 kHz to 7 735 kHz
(2 300 kHz to 2 495 kHz,
2 940 kHz to 4 215 kHz,
4 540 kHz to 5 175 kHz,
5 820 kHz to 6 455 kHz,
7 100 kHz to 7 735 kHz)
9 500 kHz to 21 975 kHz
(9 500 kHz to 10 135 kHz,
11 580 kHz to 12 215 kHz,
13 570 kHz to 13 870 kHz,
E
15 100 kHz to 15 735 kHz,
17 500 kHz to 17 985 kHz,
18 015 kHz to 18 135 kHz,
21 340 kHz to 21 975 kHz)
Bluetooth
Version ............................Bluetooth 3.0 certified
Output power ................... +4 dBm Maximum
(Power class 2)
Note F
Specifications and the design are subject to
DEH-X66BT/XNUC
5 6 7 8
7
1 2 3 4
A DEH-X6690BT/XNID
General CD player
Backup current.................. 4.0 mA or less audio)
Nose ................................ 188 mm × 58 mm × 15 mm
B D
Chassis ............................ 178 mm × 50 mm × 165 mm USB
Nose ................................ 170 mm × 46 mm × 15 mm USB standard specification
Weight ............................. 1 kg ................................... USB 2.0 full speed
Maximum current supply
................................... 1 A
Audio USB Class ....................... MSC (Mass Storage Class)
Maximum power output ... 50 W × 4 File system....................... FAT12, FAT16, FAT32
70 W × 1/2 Ω (for subwoofer) MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
Continuous power output WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
................................... 22 W × 4 (50 Hz to 15 000 Hz, audio)
5 % THD, 4 Ω load, both chan- (Windows Media Player)
nels driven) WAV signal format ...........Linear PCM & MS ADPCM
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable) (Non-compressed)
C
................................... 2.0 V
Loudness contour ............ +10 dB (100 Hz), +6.5 dB FM tuner
(10 kHz) (volume: –30 dB) Frequency range ..............87.5 MHz to 108.0 MHz
Equalizer (5-Band Graphic Equalizer): Usable sensitivity ............. 9 dBf (0.8 µV/75 Ω, mono, S/N:
Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/ 30 dB)
8 kHz Signal-to-noise ratio ......... 72 dB (IEC-A network)
Subwoofer (mono):
MW tuner
Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/
Frequency range .............. 531 kHz to 1 602 kHz (9 kHz)
125 Hz/160 Hz/200 Hz
530 kHz to 1 640 kHz (10 kHz)
Slope ............................... –12 dB/oct, –24 dB/oct
Gain ................................ +6 dB to –24 dB
D
SW tuner
Frequency range .............. 2 300 kHz to 7 735 kHz
(2 300 kHz to 2 495 kHz,
2 940 kHz to 4 215 kHz,
4 540 kHz to 5 175 kHz,
5 820 kHz to 6 455 kHz,
7 100 kHz to 7 735 kHz)
9 500 kHz to 21 975 kHz
(9 500 kHz to 10 135 kHz,
11 580 kHz to 12 215 kHz,
13 570 kHz to 13 870 kHz,
E 15 100 kHz to 15 735 kHz,
17 500 kHz to 17 985 kHz,
18 015 kHz to 18 135 kHz,
21 340 kHz to 21 975 kHz)
Bluetooth
(Power class 2)
F Note
DEH-X66BT/XNUC
8
1 2 3 4
5 6 7 8
DEH-X6650BT/XNCS
A
General CD player
Backup current................. 4.0 mA or less audio)
Nose ................................ 188 mm × 58 mm × 15 mm
D B
USB
Chassis ............................ 178 mm × 50 mm × 165 mm
USB standard specification
Nose ................................ 170 mm × 46 mm × 15 mm
................................... USB 2.0 full speed
Weight ............................. 1 kg Maximum current supply
................................... 1 A
USB Class ....................... MSC (Mass Storage Class)
Audio
File system....................... FAT12, FAT16, FAT32
Maximum power output ... 50 W × 4
MP3 decoding format ......MPEG-1 & 2 Audio Layer 3
70 W × 1/2 Ω (for subwoofer)
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
Continuous power output
audio)
................................... 22 W × 4 (50 Hz to 15 000 Hz,
(Windows Media Player)
5 % THD, 4 Ω load, both chan-
WAV signal format ...........Linear PCM & MS ADPCM
nels driven)
(Non-compressed)
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable) C
................................... 2.0 V FM tuner
Loudness contour ............ +10 dB (100 Hz), +6.5 dB Frequency range .............. 87.5 MHz to 108.0 MHz
(10 kHz) (volume: –30 dB) Usable sensitivity ............. 9 dBf (0.8 µV/75 Ω, mono, S/N:
Equalizer (5-Band Graphic Equalizer): 30 dB)
Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/ Signal-to-noise ratio ......... 72 dB (IEC-A network)
8 kHz
Subwoofer (mono): AM tuner
Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/ Frequency range .............. 531 kHz to 1 602 kHz (9 kHz)
125 Hz/160 Hz/200 Hz 530 kHz to 1 640 kHz (10 kHz)
Slope ...............................–12 dB/oct, –24 dB/oct Usable sensitivity ............. 25 µV (S/N: 20 dB)
Gain ................................ +6 dB to –24 dB Signal-to-noise ratio ......... 62 dB (IEC-A network)
D
Bluetooth
(Power class 2)
Note
2.2 DISC/CONTENT FORMAT
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.
DEH-X66BT/XNUC
5 6 7 8
9
1 2 3 4
3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A To keep the product quality after servicing, please confirm following check points.
No. Procedures Item to be confirmed

1 Confirm whether the customer complain has The customer complain must not be
been solved. reappeared.
If the customer complain occurs with the Display, audio and operations must be
specific media, use it for the operation check. normal.
2 CD Play back a CD. No malfunction on display, audio and
(Track search) operation.
3 FM/AM tuner Check FM/AM tuner action. Display, audio and operations must be
(Seek, Preset) normal.
B Switch band to check both FM and AM.
4 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
5 Appearance check No scratches or dirt on its appearance after
receiving it for service.
See the table below for the items to be checked regarding audio:
Item to be checked regarding audio

Distortion
Noise
C
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
3.2 PCB LOCATIONS

D C CD Core Unit (S11.6VA)
D BT Unit A Tuner Amp Unit
A:DEH-X66BT/XNUC
B:DEH-X6600BT/XNUC
C:DEH-X6650BT/XNGS
D:DEH-X6650BT/XNCS
E:DEH-X6690BT/XNID
B Keyboard Unit Unit Number : QWM3617(A)
E Unit Number : QWM3616(B)
Unit Number : QWM3619(C)
Unit Number : QWM3618(D)
Unit Number : QWM3620(E)
Unit Name : Tuner Amp Unit
Unit Number :
Unit Name : Keyboard Unit
Unit Number : CWX4269
Unit Name : CD Core Unit(S11.6VA)
Unit Number : QWM3750
Unit Name : BT Unit
F
DEH-X66BT/XNUC
10
1 2 3 4
5 6 7 8
3.3 JIGS LIST
- Jigs List
A
Name Jig No. Remarks
16P FFC GGD1310 Tuner Amp Unit - CD Core Unit
Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)
- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
Grease GEM1043 CD Mechanism Module B
3.4 CLEANING
Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
DEH-X66BT/XNUC
5 6 7 8
11
1 2 3 4
4. BLOCK DIAGRAM
A
A TUNER AMP UNIT
FM/AM ANTENNA
JA401
1 5
FMMIXIN1
16
2,3 PINDIN
57
18 DACOUTL
LNAIN
FM/AM TUNER
IC401
TDA7706
34 93
I2CSCL TUN_SCL
33 94 RESET
I2CSDA TUN_SDA IC671
31 88
RSTN TUNRES S-80827CNMC-B8M
B RES
39 1 OUT VDD
2
VDD3.3V
JA892
3 KEYD 105
REMOTE
KEYD
WIRED
2 KEYAD 56
KEYAD
1 GND
FLASH ROM
SYSTEM MICRO IC681
6 COMPUTER
A B :PEB093A8
RMIC
Q531 IC601
5 MIC1P 8
VCC VDD3.3V (1/2) C D E :PEB089A8
4 MIC1N R5S726A0D216FP
iPod CP
D
IC531 25
CPPWR
337S3959
BT UNIT ILMPW
Q871
6 91
SCL CP_SCL B.UP ILM+B
CN21 CN23 CN971 2 92
SDA CP_SDA
MIC1N MIC1N MIC1N 7 24
20 15 2
RST CPRST Q872
MIC1P MIC1P MIC1P
21 13 4
19
MIC-BIAS ILMPW
22
C 7
RESET NRST_CPU
9 8
NRST_CPU 2
BTRST
BTTOSYS BTTOSYS BTTOSYS 13
11 11 6 BTRX
SYSTOBT SYSTOBT SYSTOBT 14
12 10 7 BTTX
BTDATA BTDATA BTDATA 7
13 5 12 BTDATA
BT MODULE
BTSCK BTSCK BTBCK 4

15 6 11 BT_BCK REGULATOR IC
16
BTLRCK BTRLCK
7 10
BTLRCK 6
BT_LRCK IC911
BA49183-V12
BT3.3V REG.
IC22 11 113
S-1206B33-U3 6 VDDCONT SWVDD
SW5V SW5V 1 90
BT3.3V 3 2 VCC VCC BSENS BSENS
8 VOUT VIN 1 16 9
SWVDD SWVDD 2 8
BT1.8V REG. 7 SYSPW SYSPW
2 15 VDD3.3V VDD 3
IC21 8 SW5VCNT
S-1172B18-E6 VDD1.2V VDD12 SYST
BT1.8V 1 6 5 4 COM
5 VOUT VIN SYS+B SYS+B +B B.UP
10 I
6 +BUP
BT18ON 3 ON/OFF R5S72
4
D PICKUP UNIT
(P11)(SERVICE) C CD CORE UNIT(S11.6 VA)
USB5V REGULATOR
IC551
BD9876EFJ
8
CN101 B.UP VCC
RF AMP, CD DECODER
VCC 7 7 V+3A DIGITAL SERVO/DATA • PROCESSOR
CPU
Q101 5 118
Q102 IC552 SYNC SYNC
LD LD+ LD
10 10 VDD V+3A BD2232G-G Q601
VDD
6 98
5 1 1 EN DDON
1 54 USB5V VOUT VIN LX
LD PUEN
4
MD MD 11 PD 2 FB
11 PD
7
BST
REFO
VREF REFO 93
8 8 REFOUT 3 119
EN USBCTL
AC,BD,VC,E,F 4 120
HOLOGRAM OC USBFLG
UNIT
FOM FOM ACTUATOR/

3 3 MOTOR DRIVER CN701 CN701
FOP FOP IC301
2 2
E FOCUS ACT.
BD8223EFV TD,FD VDD
VDD
9 9
VDD
VDD3.3V
TRACKING ACT. TOP 1 1 TOP IC201
SD,MD PEQ094A 55
TOM 4 4 TOM 8 VDSENS
TKO+
7 MECHA VD
TKO- Q751
10 VD VD
FCO+ VD 2 2 B.UP
9 R
FCO- 1 1 Q752
SOP 3 RG
SPINDLE SPO+
MOTOR M SOM 2 CNT
23 40
CLCONT RG
SPO-
22 41 85
LDIN LOEJ VDCONT
LCOP 5
LOADING/CARRIAGE SLLDO+ MUTE 21 39
CONT
MOTOR M LCOM 4
SLLDO-
29 RESET RESET 33
RESET 8 8 CDRST
38
DSCSNS
35
HOME
CD DATA (CDSRQ,CDSTBY,SKIP, CD DATA (CDSRQ,CDSTBY,SKIP,
SCL,SDA,DATA,BCLK,LRCK,WAIT) SCL,SDA,DATA,BCLK,LRCK,WAIT)
S903 S901
DSCSNS HOME
F
DEH-X66BT/XNUC
12
1 2 3 4
5 6 7 8
ELECTRONIC VOLUME/
SOURCE SELECTOR
IC201
PM9013A
JA251
TUNL 40 35 PL PL 3
INAN1L OUTPL
PREOUT
RCAG 1
A :DEH-X66BT/XNUC FL FL 6
B :DEH-X6600BT/XNUC RCAG 4
C :DEH-X6650BT/XNGS Q252 Q251
P251
D :DEH-X6650BT/XNCS
E :DEH-X6690BT/XNID
VDD3.3V
B
19 JA901
81 MCLK
EVOL_MCK FUSE 10A
104 20 B.UP 18
EVOL_LRCK LRCLK
17
103 21
EVOL_BCK BCLK 15 B.UP
106 22 33 12(11)
EVOL_DATA DIN OUTFL FLIn
110 23
EVOL_DT DATA 34 13(12)
108 24 OUTRL RLIn 10(9) FL+
EVOL_CK CLK FL+ 1
111 25 MUTE 8(7) FL-
EVOL_CS STB
87 26 Q301 POWER AMP FL- 3
EVOL_RST RESETB (1/2) IC301 6(5) RL+
AUXL 37 PA2032A RL+ 5
INBP4L
4(3) RL-
RL- 7
POWER SUPPLY
ILM+B Q301
(2/2)
117 23(22) 26(25) BREM&A.ANT
MUTE MUTE H-SW 14
17 2(1) C
ANTPW OFF.DET
ASENS
Q941
89 ACC
ASENS 13
113
SWVDD
B
90
BSENS
8
SYSPW KEYBOARD UNIT
SYSTEM MICRO JA1921
FRONT AUX
B.UP COMPUTER CN801 CN1931 AUXR 3
IC601 AUXL 2
(2/2) AUXL AUXL
19 19
R5S726A0D216FP SORUCE S1842 AUXGND 1
SSENS 35 SOURCE SOURCE 4 2

18 18
MULTI-CONTROL 3 1
S1830
53 ROT0 ROT0 2 5 KDT2
ROT0 6 6 D
54 ROT1 ROT1 1 4 KST1
ROT1 4 4
3 94 KDT0
P04
ILM+B 5 5 ILM+B 95 KDT1
P05
96 KDT2
SWVDD 3 3 SWVDD P06
5 118 97 KDT3
SYNC P07
90 KST0 KEY MATRIX
Q601 P00
22 KYDT KYDT 99
6 98 KYDT 8 8 UTX/P34 91 KST1
DDON IC801 LCD DRIVER/ P01
KEY CONTROLLER 92 KST2
TC7SET08FUS1 P02
23 2 4 DPDT DPDT 100 IC1802 93 KST3
DPDT 10 10 URX/P35 PDC202B P03
LCD
119 34 DSENS DSENS V1802
USBCTL DSENS 20 20
120 98
USBFLG ILM+B RMIN/P73/INT/T0IN
REMOTE CONTROL
RGB DRIVER SENSOR
IC1851 Q1852 (1/2)
BH2228FV 1 IC1941
PNJ4833M
AO4
4 E
Q1853 (1/2)
55
VDSENS RED LCD
5 GREEN LCD
AO5
Q1853 (2/2)
B.UP 21 RGBDT RGBDT 12 BLUE LCD
RGBDT/DIMMER 7 7 DI
15 RGBST/ILMCLR2 RGBST 10 RED Key
RGBCS/ILMCLR2 14 14 CSB
6
11 RGBCK/ILMCLR1 RGBCK 11 AO6 GREEN Key
RGBCK/ILMCLR1 12 12 CLK Q1851 (1/2)
85 BLUE Key
VDCONT
1 Q1859 Q1858 Q1857 Q1868 Q1867 Q1866

AO1
Q1851 (2/2)
33
CDRST
D1882, D1885,
2 D1883, D1886
AO2
Q1852 (2/2) D1884
3
AO3 F
CN1911
ILM+B ILM+B
USB5V USB5V
USB5V 11 11 2
USB
49 DM DM DM
DM 13 13 3
50 DP DP DP
DP 15 15 4
DEH-X66BT/XNUC
5 6 7 8
13
1 2 3 4
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON
Vcc = 1.2 V Vcc : Pin 12, 20, 43, 78, 86, 109
PVcc = 3.3 V PVcc : Pin 3, 16, 28, 36, 48, 69, 82,101, 112
BSENS
B Pin 90
BSENS = L
ASENS
Pin 89
ASENS = L
C DSENS
Pin 34
DSENS = L
Starts
communication
with Grille
microcomputer.
D
300 ms
SWVDD <- H
Pin 113
300 ms
In case of the above signal, the communication

Source keys with Grille microcomputer may fail.
operative If the time interval is not 300 msec, the oscillator
may be defective.
E
Source ON
SYSPW <- H
Pin 8
Completes power-on operation.

F (After that, proceed to each source operation)
DEH-X66BT/XNUC
14
1 2 3 4
5 6 7 8
5.2 ERROR CODE LIST
ERROR CODES
If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a A
cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from
customers and facilitate failure analysis and repair work in servicing.
(1) DISPLAY METHOD

If “0xFD” error mode is displayed in CD MODE (CD MODE area for display), an error code will be displayed in the MIN (minute
display) and SEC (second display) areas.
The same code is displayed in the MIN and SEC areas.

The TNO area is blank (#0FFH), as it conventionally was.
• Display example of the head unit
Depending on the display capability of LCDs, the display format varies, as shown below. XX denotes an error number.
B
Note: In a case of an OEM product, the error display format is subject to the specifications used by the equipment
manufacturer.
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx
(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)

Code Classification Error code to be displayed Details and possible causes
07 Servo TOC reading NG TOC information cannot be read.
--> The partial disk or TOC content is illegal. C
10 Servo Carriage Home NG The pickup cannot move toward the inner track.
The CRG cannot move from the inner track.
--> Defective HOME SW; Failure in CRG movement.
11 Servo Focus NG Focusing not available
--> Disc placed upside-down; Stains on the disc; excessive vibration.
12 Servo Spindle Lock NG Spindle not locked. Subcode not readable.
Subcode NG Proper RF AMP gain not obtained.
RF-amp NG --> Defective spindle; Scratches or stains on the disc; excessive vibration.
--> A CD-R/RW disc that does not contain data loaded, or in a rare case, disc placed upside-down.
--> RF signal error.
15 Servo RF NG The digital signal from the disc cannot be detected.
--> A CD-R/RW disc that does not contain data loaded. D
17 Servo Setup NG The laser output cannot be adjusted. Focus can be easily lost.
--> Scratches or stains on the disc; excessive vibration.
30 Servo Search Time Out Failed to reach a target address. And, the search became a timeout.
--> Carriage/Tracking error; Scratches on the disc; Stains on the disc
50 Mechanism Load NG Disc loading/ejection not completed
Eject NG --> A foreign object inserted in the mechanism; Disc jammed.
51 Mechanism Failure in retried Disc could not be ejected even after disc turning had been retried.
turning for ejection --> A foreign object inserted in the mechanism; Disc jammed.
E
NOTES
• Indications of error codes are available only during disc operations, because CD operations are unavailable if a mechanical error is
generated.
• If the TOC cannot be read, It stops because of error 07.
• If you design a new head unit, be sure to use one of the display formats indicated in “Display example of the head unit.”
• The 2 high-order digits of an error code denote the main classification, shown below.
code classification
0x
1x Servo-related errors
3x
5x Mechanism-related errors
• How to restore from each error is shown below. F

Servo-related errors(0X, 1X, 3X) : Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset
Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset
Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset
DEH-X66BT/XNUC
5 6 7 8
15
1 2 3 4
A Symptoms are written in bold and causes in reg- USB storage device/iPod
ular, non-indented text. Regular, indented text is
used to indicate actions to be taken. FORMAT READ
Sometimes there is a delay between the start of play-
back and when you start to hear any sound.
Common
Wait until the message disappears and you hear
AMP ERROR sound.
This unit fails to operate or the speaker connection is
NO AUDIO
incorrect; the protective circuit is activated.
Check the speaker connection. If the message There are no songs.
fails to disappear even after the engine is Transfer the audio files to the USB storage device
switched off/on, contact your dealer or an and connect.
B
authorized Pioneer Service Station for The connected USB storage device has security en-
assistance. abled.
Follow the USB storage device instructions to
disable the security.
CD player
SKIPPED
ERROR-07, 11, 12, 17, 30
The connected USB storage device contains DRM
The disc is dirty. protected files.
Clean the disc. The protected files are skipped.
The disc is scratched.
Replace the disc. PROTECT
C
All the files on the connected USB storage device
ERROR-07, 10, 11, 12, 15, 17, 30, A0 are embedded with DRM.
There is an electrical or mechanical error. Replace the USB storage device.
Turn the ignition switch OFF and back ON, or
switch to a different source, then back to the CD N/A USB
player. The connected USB device is not supported by this
unit.
ERROR-15  Connect a USB Mass Storage Class compliant
The inserted disc is blank. device.
Replace the disc.  Disconnect your device and replace it with a
compatible USB storage device.
D ERROR-23
Unsupported CD format. CHECK USB
Replace the disc. The USB connector or USB cable has short-
circuited.
FORMAT READ Check that the USB connector or USB cable is
Sometimes there is a delay between the start of play- not caught in something or damaged.
back and when you start to hear any sound.
Wait until the message disappears and you hear CHECK USB
sound. The connected USB storage device consumes more
than maximum allowable current.
NO AUDIO Disconnect the USB storage device and do not
E The inserted disc does not contain any playable files. use it. Turn the ignition switch to OFF, then to
Replace the disc. ACC or ON and then connect only compliant
USB storage devices.
SKIPPED
CHECK USB
The inserted disc contains DRM protected files.
The iPod operates correctly but does not charge.
The protected files are skipped.
Make sure the connection cable for the iPod has
not shorted out (e.g., not caught in metal
PROTECT
objects). After checking, turn the ignition switch
All the files on the inserted disc are embedded with OFF and back ON, or disconnect the iPod and
DRM. reconnect.
Replace the disc.
F
DEH-X66BT/XNUC
16
1 2 3 4
5 6 7 8
A
ERROR-19 INOPERABLE
Communication failed. The operation was disabled.
Perform one of the following operations. Run the same command for another track.
–Turn the ignition switch OFF and back ON.
–Disconnect the USB storage device. TRY AGAIN
–Change to a different source. Unable to save thumb rating.
Then, return to the USB source.
Unable to save BookMark.
iPod failure. Unable to add station.
Disconnect the cable from the iPod. Once the Try again later.
iPod’s main menu is displayed, reconnect the
iPod and reset it. MAINTENANCE
B
Pandora system is undergoing maintenance.
ERROR-23
Try again later.
USB storage device was not formatted with FAT12,
FAT16 or FAT32. SKIP LIMIT
USB storage device should be formatted with
Skip limit reached.
FAT12, FAT16 or FAT32.
 Do not exceed the skip limit.
 Due to music licensing restrictions, Pandora
ERROR-16
limits the total number of skips per hour.
The iPod firmware version is old.
Update the iPod version. CHECK APP
iPod failure. This version of the Pandora application is not sup- C
Disconnect the cable from the iPod. Once the ported.
iPod’s main menu is displayed, reconnect the Connect a device that has a compatible version
iPod and reset it. of the Pandora application installed.
STOP CHECK DEVICE

There are no songs in the current list. Device error message displayed in Pandora applica-
Select a list that contains songs. tion.
Unable to play music from Pandora.
NOT FOUND Please check your connected device.
No related songs.
Transfer songs to the iPod. NO STATION
D
No station found.
Create a station in the Pandora application on
Bluetooth device your connected device.
ERROR-10
NO ACTIVE ST
The power failed for the Bluetooth module of this
unit. No station selected.
Turn the ignition switch OFF and then to ACC or Select a station.
ON.
If the error message is still displayed after NO BT DEVICE GO TO BT MENU TO REGISTER
performing the above action, please contact your No Bluetooth device found.
dealer or an authorized Pioneer Service Station. Follow the instructions that appear on the
E
screen.
Pandora CONN. FAILED PRESS BAND KEY TO RETRAY
ERROR-19 Bluetooth connection failed.

Follow the instructions that appear on the
Communication failed.
screen.
Disconnect the cable from the device. Once the
device’s main menu is displayed, reconnect the
CHECK APP PRESS BAND KEY TO RETRAY
device and reset it.
Connection to the Pandora application failed.
START UP APP Follow the instructions that appear on the
screen.
The Pandora application has not started running yet. F
Start up the Pandora application.
DEH-X66BT/XNUC
5 6 7 8
17
1 2 3 4
A
DISCONNECTED PRESS BAND KEY TO RETRAY
Bluetooth connection lost.
screen.
STATION FULL
A new station cannot be added.
Delete an old station to open a spot for a new
one.
CAN.T DELETE
B
The station could not be deleted.
Run the same command for another station.
NO NETWORK
The connected device is out of area.
Connect the connected device to a network.
NO SERVICE
The connected device is out of area.
Connect the connected device to a network.
C
CAN.T PLAY
The operation was disabled.
Run the same command for another station.
Apps
NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found.
screen.
D
CONN. FAILED PRESS BAND KEY TO RETRAY

Bluetooth connection failed.
screen.
DISCONNECTED PRESS BAND KEY TO RETRAY

Bluetooth connection failed.
screen.
E CHECK APP
Connection to the application failed.
screen.
START UP APP
The application has not started running yet.
screen.
DEH-X66BT/XNUC
18
1 2 3 4
5 6 7 8
5.3 CONNECTOR FUNCTION DESCRIPTION
ANTENNA INPUT MICROPHONE WIRED FRONT

INPUT REMOTE OUTPUT
15 13 11 9 7 5 3 1 CONTROL
16 14 12 10 8 6 4 2
C
REAR OUTPUT or
1 FL+ 9 NC SUBWOOFER OUTPUT
2 FR+ 10 NC
3 FL- 11 NC
4 FR- 12 NC
5 RL+ 13 ACC
6 RR+ 14 B.REM
7 RL- 15 B.UP
8 RR- 16 GND
DEH-X66BT/XNUC
5 6 7 8
19
1 2 3 4
6. SERVICE MODE
6.1 DISPLAY TEST MODE 1
A [How to enter Test mode]
Press and hold "PHONE" and "LIST" buttons together, and turn BUP and ACC on.
SOURCE LIST
PHONE
B
BAND
ROTARY
Grille condition
Conf. item Operate Show LCD RGB
C All light up PHONE + LIST Draw 1 White
All light off SOURCE No light Draw2 No light
Conf. LCD pattern 1
(* And change ILM color) BAND Draw 3 Red
Conf. LCD pattern 2 ROTARY center Draw 4 Green
Drawings Style
Draw1 ALL light up
Draw2 ALL light off
Draw3
D
Draw4
DEH-X66BT/XNUC
20
1 2 3 4
5 6 7 8
6.2 DISPLAY TEST MODE 2
The information such as the system microcomputer version is checked. A
[How to enter Test mode]

Press and hold "1" and "3" buttons together, and turn BUP and ACC on.
[Operation key]
Operation key Processing Remarks
Enter display test mode
1+3 Switch to next test mode
[Test items]
Start display test mode. Key Illumination Icon
Press and hold "1" and "3" buttons together, and turn * Initial
BUP and ACC on. Off All off condition
On (an initial value) All off

System Version information is displayed.
C
S $ $ $ $ # # #
$ PD number For PEA010A, "010A" is displayed

# System For Ver.7.01, "701" is displayed On (an initial value or
All off
microcomputer setting value of default
version menu)
Switching to next display

by pressing “ 1 ” + “ 3 ” buttons together.
Display is normally updated

Product operation is performed as usual, in appearance. On (an initial value or On (lighting condition
Switching to next display setting value of default of normal times)
by pressing “ 1 ” + “ 3 ” buttons together. menu)
E
Display update is stopped
The screen gets still when entering this item. On (an initial value or On (state when
setting value of default entering test mode)
Switching to next display menu)
by pressing “ 1 ” + “ 3 ” buttons together.
DEH-X66BT/XNUC
5 6 7 8
21
1 2 3 4
6.3 SOFTWARE VERSION UP METHOD
A
Overview
This mode is used for upgrading the MCU software of system using USB memory.
How to enter in USB rewriting mode

USB rewriting operation flow

Explanatory note
Screen display and ON/OFF of illumination
USB Characters displayed on the screen
Red frame: illumination lights up

B
Gray frame: illumination lights off
Blue characters: operation to be carried out by a user of USB rewriting function
START UPDT
Press LIST button

* After connecting USB memory in which upgrading file is stored, press LIST button.
(4) Retry count over Retry rewriting

C As the reset is internally carried out,
display and illumination go out
Check of upgrading file is started
(2) Upgrading file is not detected
Upgrading file error
CHECK FILE
First time After retry
Rewriting is started
If the power supply is turned OFF
during rewriting, retry the rewriting.
DON'T STOP
Switched every
D 5 seconds (3) Rewriting failed
PRG **/100
(1) Rewriting succeeded
CAN'T UPDT COMPLETE ERR->RETRY FILE ERROR ERR->RETRY
Display is continued until In 5 seconds, usual operation In 5 seconds, rewriting In 5 seconds, usual operation In 5 seconds, rewriting
E the power supply is turned (OFF SOURCE) is retried
is retried (OFF SOURCE)
OFF
Result of rewriting
(1) Rewriting succeeded Displayed when USB rewriting is normally terminated.
In 5 seconds, usual operation (OFF SOURCE) is started.
(2) Upgrading file error Displayed when there is no upgrading file in USB memory or the data of upgrading file is different.
Upgrading file is not detected In 5 seconds, usual operation (OFF SOURCE) is started.
If the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried, the rewriting is failed.
In 5 seconds, rewriting is retried.
(3) Rewriting failed Displayed when the writing of upgrading file in serial Flash is not normally terminated.
Or, displayed if the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried.
In 5 seconds, rewriting is retried.
(4) Retry count over Displayed when the retry becomes unavailable because the retry count is exceeded.
F The display is continued until the power supply is turned OFF. If the power supply is turned ON again, the display is not changed.
The upgrading using USB is disabled, so it is necessary to write programs in serial Flash using E10A.
DEH-X66BT/XNUC
22
1 2 3 4
5 6 7 8
6.4 CD TEST MODE
- Flow Chart A
To enter the test mode: [4] + [6] -> BUP + ACC ON
[CD] or [SOURCE] [Key]

Source ON
Contents
TRK MIN
Display
[BAND] [2]
Power On RF AMP *1
(T.Offset is adjusted) Gain switching
TRK MIN SEC TRK MIN SEC
00 00 00 GG GG GG
B
[BAND] [3] [6] [1] [>] [<] [2]

Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
S curve check *2 Close *6 *6 switching *3
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
[BAND] [1] [3] [>] [<] [2]

Power Off T.Close & AGC RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??
[BAND] [1] [3] [>] [<] [2]

Power Off F,T,RF AGC*5 F,T AGC / F.Bias CRG/TR Jump + CRG/TR Jump - Tracking Open C
F.Bias display switching RF AGC *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X
[BAND] [2]
Power Off Tracking Open
TRK MIN SEC 8X 8X 8X

or 9X 9X 9X
Operation
*1) TYP t + 6 dB t + 12 dB [Key] Test Mode
TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [BAND] Power On/Off
[>] CRG + / TR Jump + D
(Direction of the external surface)
*2) Focus Close t S. Curve t F EQ measurement setting [<] CRG - / TR Jump -
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 (Direction of the internal surface)
(TRK99MIN99SEC99) [1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
[2] RF Gain switching / Offset adjustment display /
*3) F.Offset Display t RF.Offset t T.Offset Display t Switch to the order T.Balance adjustment / T. Open
of the original
[3] F. Close,S. Curve / Rough Servo and RF AGC /
display
F,T,RF AGC
*4) 100TR Jump [6] F. Mode switching / Tracking Close
E
*5) TRK/MIN/SEC t F.AGC t T.AGC Gain t F.Bias t RF AGC
*6) CRG motor voltage = 2 [V]
After the [EJECT] key is pressed keys other than the [EJECT] key should not be pressed, until disc ejection is complete.
When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens sticks
to Wall, causing the actuator to be damaged).
In the case of 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the F
default setting.
Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows)
DEH-X66BT/XNUC
5 6 7 8
23
1 2 3 4
7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
A
- Removing the Panel Assy (Fig.1)

1 1
1 Release the two latches.
2 2
2 Release the two latches and then remove
the Panel Assy.
B
Panel Assy
Fig.1
- Removing the CD Mechanism Module (Fig.2)
1 Remove the screw. 1

2 2
2 Remove the two screws.
C The CD Mechanism Module side is made a bottom.

Heat Sink side
3 3
D CD Mechanism Module
3 Push the area and remove the two hooks. Tuner Amp Assy
4 Slide the Tuner Amp Assy in the direction

of the arrow.
Lift off the Tuner Amp Assy from the Heat Sink side.
E 5 The Tuner Amp Assy is fixed into the ditch.
6 Disconnect the FFC and then remove the

CD Mechanism Module.
6
CD Mechanism Module
F
Fig.2
DEH-X66BT/XNUC
24
1 2 3 4
5 6 7 8
- Removing the Tuner Amp Unit and the BT Unit (Fig.3) A
Tuner Amp Unit

1 Disconnect the connector.
2 Remove the two screws.
3
3 Remove the two screws and then remove
the Tuner Amp Unit.
4 Remove the screw and then remove

B
the BT Unit.
3 2 2
BT Unit
Fig.3
- Attention of removing (Fig.4)
Don’t remove this screws excluding the dismantlement

of the CD Mechanism Module.
D
CD Mechanism Module
Fig.4
DEH-X66BT/XNUC
5 6 7 8
25
1 2 3 4
- Disassembling the Panel Part (Fig.5, 6)

1. Remove the arm while bending the rib of the panel upward.
A
B
Fig.5
2. Press the upside hook and the bottom side hook of the
button at the same time, and pull out the button.
Fig.6
- Assembling the Panel Part (Fig.7, 8, 9)

1. Attach the button from the front side of the panel.
E
Fig.7
2. Attach the spring to the arm as shown in the figure.
The bended tip of the

spring is set to this side.
Hitch the spring to the groove. Fig.8
DEH-X66BT/XNUC
26
1 2 3 4
5 6 7 8
3. Fit the spring in the groove at the position shown in the figure. A
4. Fit the boss on the lower side of the arm in the lower hole of
the panel, and then warp the rib on the panel in the direction
shown in the figure and fit the boss of the arm in the panel.
Fig.9
DEH-X66BT/XNUC
5 6 7 8
27
1 2 3 4
How to carry the mecha unit

1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket.
A 2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion.
3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less)
Handling OK
Handling NG
DEH-X66BT/XNUC
28
1 2 3 4
5 6 7 8
How to remove the PU unit

1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”.
2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the A
spring edge.
3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw
so that a joint on the outer end of the feeding screw is loosened.
4. As shown in Fig 3, move the rear end of the feeding screw laterally and then upward, to remove it from the outer holder.
5. Lift the PU unit to disengage it from Part B of the chassis (Fig 4), and remove the PU unit.
(Cautions) When re-installing the PU, be sure to first nip the chassis and the PU unit (Fig 4) at the position B.
Also, make sure to fully hook the feeding screw biasing spring (Fig 2a).
Please follow the service manual for adjustment of the PU unit after the re-installation.
Slide toward inner circumference

Fig 2a Fig 2b
B
Fig 1
Fully-hooked state Tentatively-hooked state
C
The spring is below a resin
flange and is built inside the
B A sheet metal bending.
Fig 3 Fig 4
[Incorrect built-in state]

The chassis is not nipped between
Outer holder Normal built-in state
the PU case and the PU rack.
Rear end of feeding screw
DEH-X66BT/XNUC
5 6 7 8
29
1 2 3 4
8. EACH SETTING AND ADJUSTMENT

8.1 CD ADJUSTMENT
A
1) Cautions on adjustments 2) Test mode

In this product the single voltage (3.3 V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65 V) To enter the test mode.
instead of the GND. [4] + [6] -> BUP + ACC ON
If you should mistakenly short the REFO1 with the GND CD Source ON
during adjustment, accurate voltage will not be obtained,
and the servo’s misoperation will apply excessive shock To exit from the test mode.
to the pickup. To avoid such problems: Turn off the ACC and back up.
a. Do not mix up the REFO1 with the GND when
connecting the (-) probe of measuring instruments. Notes:
B Especially on an oscilloscope, avoid connecting the (-) a. During ejection, do not press any other keys than the
probe for CH1 to the GND. EJECT key until the loaded disc is ejected.
b. In many cases, measuring instruments have the same b. If you have pressed the [2] key or [3] key during focus
potential as that for the (-) probe. Be sure to set the search, turn off the power immediately to protect the
measuring instruments to the floating state. actuator from damage caused by the lens stuck.
c. If you have mistakenly connected the REFO1 to the GND, c. For the TR jump modes except 100TR, the track jump
turn off the regulator or the power immediately. operation will continue even if the key is released.
d. For the CRG move and 100TR jump modes, the tracking
Before mounting and removing filters or leads for loop will be closed at the same time when the key is
adjustment, be sure to turn off the regulator. released.
e. When the power is turned off and on, the jump mode
For stable circuit operation, keep the mechanism is reset to the single TR (91), the RF amp gain is set to 0 dB,
C operating for about one minute or more after the and the auto-adjustment values are reset to the default
regulator is turned on. settings.
In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.
The RFAGC and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.
The load and eject operation is not guarantied with the

D
mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.
DEH-X66BT/XNUC
30
1 2 3 4
5 6 7 8
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT
F L.P.F.
E Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF
F 100 kohm
REFO1 390 pF
VREF
D
L.P.F.
Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the > and < buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking
balance adjustment the display should now read "81". Press key 3. The display will change,
returning to "81" on the fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase E
difference is within 75 . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-X66BT/XNUC
5 6 7 8
31
1 2 3 4
Grating waveform Ech -> Xch 20 mV/div, AC

Fch -> Ych 20 mV/div, AC
A
0 degrees 30 degrees
DEH-X66BT/XNUC
32
1 2 3 4
5 6 7 8
8.3 PCL OUTPUT CONFIRMATION
A
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN IC601(Pin 99) terminal to H.
The clock signal is output from the PCL terminal IC601(Pin115).
The frequency of the clock signal is 600 kHz that is divided by 20th of the oscillation frequency of X601 (12MHz).
The clock signal should be 600 kHz(- 25 Hz, + 25 Hz).
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.
9. EXPLODED VIEWS AND PARTS LIST

NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
"
Screw adjacent to mark on the product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.) F
DEH-X66BT/XNUC
5 6 7 8
33
1 2 3 4
9.1 PACKING
X6600BT/XNUC
X6650BT/XNGS
X6650BT/XNCS
B X6690BT/XNID
X66BT/XNUC
A
X6600BT/XNUC
C X6650BT/XNGS
X6650BT/XNCS
X6690BT/XNID
X6600BT/XNUC
X6650BT/XNGS
X6650BT/XNCS
X6690BT/XNID
X6650BT/XNGS
X6650BT/XNCS
X6690BT/XNID
A
X66BT/XNUC
X6600BT/XNUC
X66BT/XNUC
X6600BT/XNUC
F
X6600BT/XNUC
X6650BT/XNGS
X6650BT/XNCS
X6690BT/XNID
DEH-X66BT/XNUC
34
1 2 3 4
5 6 7 8
(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDP1480 11 Screw See Contrast table (2)

2 Polyethylene Bag See Contrast table (2) 12 Handle QNC3021
A
3 Protector See Contrast table (2) 13 Screw TRZ50P080FTC
4 Protector See Contrast table (2) 14 Unit Box See Contrast table (2)
5 Protector See Contrast table (2) 15 Contain Box See Contrast table (2)
6 Microphone Assy CPM1083 16 Case Assy See Contrast table (2)

7 Holder CZN7192 17 Card Remote Control Unit QXE1044
8 Cushion CZN7193 18-1 Owner's Manual See Contrast table (2)
9 Screw See Contrast table (2) * 18-2 Warranty Card See Contrast table (2)
10 Polyethylene Bag CEG1160 * 18-3 Service Network See Contrast table (2)
B
(2) CONTRAST TABLE
DEH-X66BT/XNUC, DEH-X6600BT/XNUC, DEH-X6650BT/XNGS, DEH-X6650BT/XNCS and DEH-X6690BT/
XNID are constructed the same except for the following:
DEH-X66BT/ DEH-X6600BT/ DEH-X6650BT/ DEH-X6650BT/ DEH-X6690BT/
Mark No. Description
XNUC XNUC XNGS XNCS XNID
2 Polyethylene Bag CEG1173 CEG1173 QEG3001 QEG3001 QEG3001
3 Protector CHP4103 Not used Not used Not used Not used
4 Protector CHP4104 Not used Not used Not used Not used
5 Protector Not used CHP4594 CHP4594 CHP4594 CHP4594
9 Screw BPZ20P060FTC BPZ20P060FTC Not used Not used Not used
C
11 Screw CRZ50P090FTC CRZ50P090FTC Not used Not used Not used
14 Unit Box QHG3471 QHG3470 QHG3473 QHG3472 QHG3474
15 Contain Box QHL3471 QHL3470 QHL3473 QHL3472 QHL3474
16 Case Assy Not used Not used QXA3129 QXA3129 QXA3129
18-1 Owner's Manual QRD3195 QRD3195 QRD3197 QRD3196 QRB3341
* 18-2 Warranty Card QRY3001 QRY3001 Not used Not used CRY1304
* 18-3 Service Network Not used Not used Not used Not used CRY1305
Owner's Manual,Installation Manual

Part No. Language D
QRD3195 English, French, Spanish(Espanol)
QRD3196 English, Spanish(Espanol), Portuguese(B)
QRD3197 English, Traditional Chinese, Arabic, Persian
QRB3341 English
DEH-X66BT/XNUC
5 6 7 8
35
1 2 3 4
9.2 EXTERIOR
D
DEH-X66BT/XNUC
36
1 2 3 4
5 6 7 8
(1) EXTERIOR SECTION PARTS LIST

1 Screw ASZ26P050FTC 27 Detachable Grille Assy See Contrast table (2)

2 Screw BSZ26P060FTC 28 Screw BPZ20P100FTC
A
3 Screw BSZ26P080FTC 29 Spring CBH2210
4 Screw BSZ26P120FTC 30 Button (EJECT) QAC3131
5 Cord Assy CDP1480
31 Button (1-6) QAC3136
6 Spring QBH3001 32 Button (DETACH) QAC3137
7 Cover QNM3029 33 Button (PHONE) QAC3139
8 Panel QNS3126 34 •••••
9 Arm QNV3025 35 •••••
10 Button QNV3026
36 Cover QNS3615
11 CD Mechanism Module (S11.6VA) CXK5805 37 Lighting Conductor QNV3074 B
12 FFC QDE3028 38 Lighting Conductor QNV3075
13 FFC QDE3029 39 Segment LCD (V1802) CAW2041
14 Case QNB3014 40 Holder QNC3068
15 Holder QNC3020
41 •••••
16 Panel QNS3576 42 Lighting Conductor QNV3073
17 Tuner Amp Unit See Contrast table (2) 43 Rubber Connector QNV3079
18 Screw BPZ26P080FTC 44 Knob Unit QXA3670
19 Screw BSZ26P060FTC 45 Spring YBL5010
20 Screw BSZ26P120FTC
46 Button Unit QXA3945 C
21 Holder QNC3053 47 Grille Unit See Contrast table (2)

22 Heat Sink See Contrast table (2) 48 Door QAT3012
> 23 Fuse (10 A) YEK5001 49 Card Remote Control Unit QXE1044
24 BT Unit QWM3750 50 Cover CNS7068
25 BT Module YWX5044
51 Cushion QNM3097
26 Shield Case YNC5123
(2) CONTRAST TABLE

DEH-X66BT/XNUC, DEH-X6600BT/XNUC, DEH-X6650BT/XNGS, DEH-X6650BT/XNCS and DEH-X6690BT/
XNID are constructed the same except for the following: D
DEH-X66BT/ DEH-X6600BT/ DEH-X6650BT/ DEH-X6650BT/ DEH-X6690BT/

Mark No. Description
XNUC XNUC XNGS XNCS XNID
17 Tuner Amp Unit QWM3617 QWM3616 QWM3619 QWM3618 QWM3620
22 Heat Sink QNR3010 QNR3010 QNR3002 QNR3010 QNR3002
27 Detachable Grille QXA3904 QXA3922 QXA3906 QXA3923 QXA3907
Assy
47 Grille Unit QXA3949 QXA3948 QXA3951 QXA3950 QXA3952
DEH-X66BT/XNUC
5 6 7 8
37
1 2 3 4
9.3 CD MECHANISM MODULE
A
B
(A)
(B)
B
(A) (B)
(A)
(A)
C B C
(A)
D
(A)
(A)
(A)
(B)
(A)
(B)
(A) C
(A) : GEM1024
F
(A)
(B) : GEM1043
DEH-X66BT/XNUC
38
1 2 3 4
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST

1 ..... 50 Damper CNW1198

2 Screw BSZ20P040FTC A
3 Screw(M2 x 4) CBA1835 51 Arm CNW1726
4 Washer CBF1038 52 Motor Unit(M2)(LOAD/CRG) CXC4026
5 Spring CBH3010 53 Screw Unit CXC8894
54 Arm Assy CXE6232
6 Spring CBH2855 55 Washer CBF1037
7 Spring CBH2856
8 Spring CBH2860 56 Washer CBF1038
9 Screw BSZ26P060FTC 57 Arm CND6242
10 Spring CBH3011 58 Collar CNW2444
59 Roller CNW2500
11 Coil Spring CBH3095 60 Gear Unit CXE6225 B
12 Spring CBH3014
13 Spring CBH3015 61 Washer YE15FTC
14 Spring CBH3016 62 Chassis Unit CXE4528
15 Spring CBH3017 63 Motor Unit(M1)(SPDL) CXE2273
64 Screw JFZ20P025FTC
16 Spring CBH3086 65 Screw JGZ17P022FTC
17 Spring CBH3019
18 ..... 66 Screw EBA1028
19 Leaf Spring CBL1824 67 CD Core Unit (S11.6VA) CWX4269
20 PU Unit(P11)(Service) CXX4754 68 Chassis CNA3181
C
21 Bracket CND4553
22 Arm CND6406
23 Bracket CND6127
24 Bracket CND5710
25 Lever CND5398
26 Sheet CNN3678
27 Rack CNV8342
28 Guide CNW2240
29 Roller CNW1172
D
30 .....
31 Arm CNW2241
32 Roller CNW1175
33 .....
34 Arm CNW1177
35 Arm CNW1178
36 Gear CNW1180
37 Gear CNW1181
38 ..... E
39 Gear CNW1183
40 Rack CNW1184
41 Gear CNW1185
42 Gear CNW1186
43 Gear CNW1187
44 Gear CNW2287
45 Clamper CNW1190
46 Arm CNW1192
F
47 Holder CNW1193
48 Holder CNW1194
49 Damper CNW1197
DEH-X66BT/XNUC
5 6 7 8
39
1 2 3 4
10. SCHEMATIC DIAGRAM

10.1 TUNER AMP UNIT (GUIDE PAGE)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A-a A-b
Large size
SCH diagram
A-a
*1
C457 4700p/25 TUNR
*1 CD C CN70
4 /CDSTBY
TUNER C456 4700p/25 No SW SW Model
/CDSRQ
TUNL
8 RESET
GND
1u/6.3
CN701
6 SKIP
C464
FM/AM ANTENNA
9 VDD
7 SDA
5 SCL
VD
VD
AGND A, B, D C, E
VKN1192-
JA401 FM: -14.7 dBs
C448 0.1u/10 9p/50

C419
CTF1786-
C449
NM 15p/50
10
1
2
3
C450
9p/50
X401
DCH1246
*1
CTF1786-
YKS5041- AM: -14.5 dBs 36.48MHz AGND MECHA VD
L420
C420 NM 0.01u/16
L419
TUNGND
2 1
C445 0.1u/10
X2
HSPC16701B02
4 GND2 C421 3p/50 NM
C447 1u/10
3
NM
CDSRQ
RESET
DGND1
3 DGND 7.4V
KN2
DATA
CDSTBY
VDD4
SDA
C423 NM
SCL
8p/50
P402
A-a
P401
A-b
SKIP
Guide page
NM
0.1u/10
1 2
C453
VD2 Q751
C446
M2R6TP_GND GND1 R416 NM
C709
X1 100p/50 22p/50
NM
C428 KTD2092
C452
1u/10
VD1
C455 CSS1848-
0.22u/16 C432 82p/50 2p/50 R701
CCG1201-A-T 10u/10
L418 NM
C435 0.47u/10 1u/10 47k
R753
47k
L417
C751 NM
R417
C454 NM R702
0.1u/10
NM
C753
RFGND
C451
L416 C439 NM 0.1u/16
NM 100k
R752
NM
390
1/4
R415 0 C459 100p/50 1000p/50
*1 VDCONT Q752
64
63
62
61
60
59
58
57
56
55
54
53
52
51
VDDIO1V2 50
49
L414 NM L415 C447 1u/10 NM
PLLTEST
Detailed page C467
TVDAC
A-a A-b
TCFM
OSCOUT
DACOUTR
R401
R402
NM
DACOUTL
VREFDEC
1 48 C448 0.1u/10 0.01u/16 3 4
OSCIN
220
750
GND-REF
GND-ADC_DAC
VCC-REF
VCC-ADC_DAC
GND-PLL
0.1u/10
VDDPLL1V2
VCC-PLL
0.1u/10
R754
C444 2 5 GND
10k
2 47 2.2u C467 NM 0.1u/10
RN731VN
DZ2J082M0
CCG1218- 1 6
RN731VN
3 46 L405 68n NM
D402
D401
C401 FMMIXDEC C443 RN4983 5 4

RFGND
D751
B
0.1u/10 4 L406 CTF1389
45 NM NM
150
L401
C752
FMMIXIN2 6 3
C410 0.27u 5 TEST 44
FMMIXIN1 FMPINDRV VDD_CORE
L407 NM 0.27uH 7 2
33p/50 C402 6 FMPINDDEC GND1V2 43
0.01u/16 L408 4.7uH 1.5uH
0.01u/16
GNDRF
0.01u/16
R715
0.01u/16
GPIO0 8 1
6p/50
C409
C408
C407
C406
C405
C403
NM
7 42
L402
0.15u
TCAM GPIO1 L409 NM 0.39uH

R703
220
220
100
220
100
1u/10 8 GPIO2 41
L410 47uH 2.2uH GND 4.7k
1k
AGND VCCRF IC401 GPIO3
orRFGND C404 NM 9 GPIO4 40
CK_SEL TDA7706 R403 390 330
R711
10 GPIO5 39 R704 100k
RF GND GNDVCO GPIO6 R408 470 360
L403 11 38
R706
R707
R708
R709
R710
C412 LFREF GPIO7 R409 NM 0 C70
CTF1786- 0.1u/10 C411 12 37 R705
C413
0.1u/10
LF1 GPIO8 R411 680 390 NM
L701
0.01u/16 13 36
NM
PINDDEC C701 NM
A GND VCCVCO
PINDIN
GND3V3
C442
C445 0.1u/10 NM
C414 0.01u/16
VREG3V3
14 35
VCCREG1V2
*1 0.01u/16 C70
RDSINT
TCAM2 VDD3V3 C465 NM 0.01u/16
GNDSLINK
AMMIXIN1
AMMIXIN2
RFGND
LNAOUT2
LNADEC2
L404 15 0.1u/10
RSTN
C415 34
GNDLNA
CCG1192- TUN_SCL
LNADEC
LNAOUT
REG1V2
I2CSCL
LNAIN2
C466 NM 1u/10 R724 NM

DGND
LNAIN
0.1u/10
CTF1786- 10u
I2CSDA 33
0.1u/10
VDIG
16 TUN_SDA
C417
C461
C416
C468 NM 1u/10 NM
NM
RFGND
L413
CTF1786-
C418
0.022u/16 C464 NM DCH1246 GND
17
18
19
20
21
22
23
NM 24
25
26
27
28
29
30
31
32
GND
C419 15p/50 R403 C424 C461 0.01u/10 NM
C420
0.1u/10
RFGND
0.1u/10
C427
R409 0
NM
TUN_RST
C426
0.01u/16 L406 390 0.01u/16 *1 SW B.UP

C436 NM
CTF1389 C425
C460
L408 GND SW5V

CCG1192-
C437 NM
R404
4.7u
1000p/50
0.1u/16
1M
R410
1u/10
C438
L405
NM
10u C468
C440
C439
L407
68n 3.3V
8p/50
C423
R407
0.27u C430
1M
33
VDCONT
1000p/50
VDSENS
CDSTBY
CD_SDA
CD_SCL
C422
*1
CDSKIP
NM
CDSRQ
CDRST
RFGND
*1 *1
0.39u
100p/50
L409
C431 NM DGND
C428
R406
R408
470
3p/50
C421
R412 R413
*1 1/4W 8.2 1/4W
10p/50
8.2
DGND C441
NM
VDCONT
MCLK
R405
BSENS
ASENS
FLASH ROM
RESETB
CDWAIT
C463
TUN_RST
L411 NM
82p/50
R411
0.47u/10
*2
C432
NM
680
C435
C429 L410
NM
C434
R414 0
*2
R681
IC681
R684
RF GND
47k
0.01u/16
47k
C466 1u/10 47u IC681
0.01u/16
C465 *1 C462 RF GND RF GND C433
*1 *1 C459
100p/50 1 8
*1 A, B PEB093A8 CS VCC
C458 1000p/50 2 NC/SIO3 7
NM RFGND DGND NM C, D, E PEB089A8
NM
RFGND DGND SO/SIO1
AGND RF GND DGND GND DGND AGND 3 SCLK 6
WP/SIO2
R682
47k
4 5
GND SI/SIO0
C682
KN1 PEB093A8
M2R6TP_GND
CN971
VKN1192- BT Connector
22p/50
C625
0.1u/10
VCC 16
R638
C622
47k
NM
C971
VCC 15
GND 14 C973
47p/50
GND 13 R974 100
C623 0.1u/10
BTDATA R636
BTDATA 12
47k
C621 0.1u/10
R975
R632
100 BT_BCK
220
220
220
100
220
220
220
47k
BTBCK 11
C620
R635 1k
R634 1k
0 1 /10
47k
R976 100 BT_LRCK R637
C624
0.1u/10
BTLRCK 10
L971
R633
R631
R630
R629
R628
R627
R626
R625
GND 9 47k
NM
BT_RST
NRST_CPU 8
BTTX
CN23 SYSTOBT 7
R971 NM BTRX
90
89
88
87
86
85
84
83
82
81
80
MD_CLK 79
78
77
76
75
74
73
72
71
70
69
68
R640
R639
BTTOSYS 6
4.7k
4.7k
VDCONT
TUNRES
QSPCLK
MD_BOOT
C972
QSSL
QIO1
Vss
NM
EVOL_MCK
R972 91
QIO3
QIO2
QIO0
5 NM
Vss
Vcc
PVcc
/ASENS
GND CP_SCL
Vcc
Vss
PVcc
/BSENS
EVOL_RST
/CDWAIT
MIC1P 4 CP_SDA 92
R641
GND 3 TUN_SCL 93
R973 NM GND
R642
MIC1N 2 TUN_SDA NM 94
2.2k TUN_SDA CP_SCL
C974
GND 1 CD_SCL NM 95 CD_SCL CP_SDA IC601
MIC1P
MIC1N
GND CD_SDA 96 TUN_SCL R5S726A0D216FP

GND CD_SDA
GND
CDSRQ 97 /CDSRQ *3
JA892 TESTIN 98
R669
R668 DDON
47k
47k
YKS5035- R643 99
(RMIC) MIC1P DDON
TESTIN A, C
6 100k
5 MIC1N 100 Vss B, D
W.REM 4
3
Q601
LTC014YEB C626 101 PVcc E
2 0.1u/10
&MIC (W/R) 1
VA892 NM
KEYD C627 22p/50 102 BT_TESTMD

BT_TESTMD
1000p/50
1000p/50
1 R891 KEYD2
VA891
1k R644 100
C894
KEYD 103
NM
C893
3 BCLK EVOL_BCK
NM
R893
KEYAD KEYAD2 KEYAD 22p/50

2 LRCLK R645 100 104 EVOL_LRCK
R892 1k C628
C891
JA891
C892
0.1u/16
105
0.1u/16
only A, BD602 KEYD

D
R646
GND NM
10k
106 EVOL_DATA
RB551VM-30
KEYD 107
DIN R647 Vss
100
GND CLK 108 EVOL_CK
Q531 R648
22p/50
1k C629
C631
L531 LSAR523UB 109 Vcc

NM DATA R649 1k 0.1u/10 110 EVOL_DT
R536 4.7k CPPWR STB R650 1k 111
EVOL_CS
0.1u/10
R531
R540
47k
C531
C630 112 PVcc

R533
R532
2.2k
2.2k
NM CP_SCL 0.1u/10
R537 100 SWVDD5 113 SWVDD
R539 CP_SDA 114 Vss
R538 100 PCL 115
R651 47k
NM PCL
CPRST RAM_MON 116
RAM_MON
R534 2.7k
SYNC
RGBDT/DIMMER
IC531
RGBCK/ILMCLR1
RGBCS/ILMCLR2
MUTE 117
B.UP
4.7u
USB5V MUTE USBCTL

3.3V
337S3959 CMS03
L551 USB&USB5V C553 D551 R652 SYNC 118 /USBFLG
1 8 CTH1524- 0.01u/16 SYNC
BT_TESTIN
BT_LRCK
2.2k 119
CCG1222-
GND PAD VCC USBCTL

BTDATA
R535 4.7k
220u/16
4 BT_BCK
SYSPW
2 7
C552
C551
ANTPW
BTRST
ILMPW
9
C565
1u/16
NM
C570
RB056L-40
BTRX
KYDT
120
BTTX
PVcc
SDA RST
4.7u
FLG
ROM
3 PVcc
IC551
220u/6.3
Vss
3 6
Vss
Vcc
Vss
NM
Vcc
D552
R552
BD9876EFJ
1u/10
C564 CCG1201-
470
R661
NC1 SCL
0
NM
4 5
0.1u/10
R653
C532
NM
6800p/25
1 8
1
2
6
7
8
9
C555
10
11
12
13
14
15
16
17
18
19
20
21
22
23
NC2 NC3 Lx VCC
C558
LX VCC
TP1
2 7 10k
C633
R555
GND 9 BST
C557
GND
NM
C556
C554
GND BST
180k D
ROM
3 6 DDON BTTESTIN
R553
GND VC EN
R551
0.1u/10
VC FIN EN
C603 0.1u/10
R664 10k
6.8k
4 5
47k
SYNC
R601
0.1u/10
FB SYNC
C604
0.1u/10
47k
C601
R602
FB SYNC
47k
NM
C563
R603
iPod CP@(2.0C)
43k D
C602
R554
GND
GND GND
IC552
RGBDT
BD2232G-G
R662
GND 1 5
NM
VIN VOUT D GND

2
GND FLG
R663
3 4 FLG
C569 NM
NM
EN OC
C562
C561
NM
1u/10
E
C560
C559
1u/10
NM
USBCLT
RGBST/ILMCLR2
RGBCK/ILMCLR1
RGBDT/DIMMER
USBCTL
DGND
SYSPW
BTDATA
BT_LRCK
GND
BT_BCK
BT_RST
OFFSET
ILMPW
BTRX
KYDT
BTTX
VBUS
DSENS
RGBDT/DIMMER
R802
2.2k
C801
CN801
CKS6452- 220p/50 J
DSENS 20
R801 2.2k R805 100
AUXL 19 GND R803 22k
18
NOTE : SOURCE
22k
R806
R807
100
100
AUXR 17 R804
Symbol indicates a resistor. AUXGND 16 L8
11
No differentiation is made between chip resistors and DP 15
RGBST/ILMCLR2 14
discrete resistors. 44
DM 13
Symbol indicates a capacitor. CTF1
No differentiation is made between chip capacitors and B RGBCK/ILMCLR1
USB5V
12
11
US5V
10
discrete capacitors. CN1931 DPDT
USBGND 9
NM
R818
KYDT 8
The > mark found on some component parts indicates A DEH-X66BT/XNUC RGBDT 7
ROT0 6
the importance of the safety factor of the part. B DEH-X6600BT/XNUC ILM+B 5
Therefore, when replacing, be sure to use parts of C DEH-X6650BT/XNGS ROT1 4
F
VA801 EZJP0V270RM
SWVDD 3
identical designation. D DEH-X6650BT/XNCS
D804 DZ2S068C
D803 DZ2S068C
DZ2S068C
D802 DZ2S068C
D805 DZ2S068C
D806 DZ2S068C
D807 DZ2S068C
D808 DZ2S068C
D809 DZ2S068C
ILMGND 2 DGND
NM
NM
NM
D801
NM
NM
C806 0.1u/16
ILMG
0.1u/16
C807 1u/10
C803
NM
1
E DEH-X6690BT/XNID DGND NM
C802
NM : No Mount USGND C804

C814
C813
C805
D810
D811
NM
C808
A GRILLE
DGND USBGND ILM GND
DEH-X66BT/XNUC
40
1 2 3 4
5 6 7 8
A-b
D C CN701 C707 ROL
4 /CDSTBY
RL
FM: -5.7 dBs
/CDSRQ
NM
8 RESET
15 PGND
11 DATA
13 LRCK
FL
12 BCLK
16 WAIT
AM: -5.5 dBs

GND
701
6 SKIP
14 GND
9 VDD
7 SDA
A
5 SCL
VD
VD
C708
AUX:+9.3 dBs TUNER AMP UNIT
10u
N1192-
NM
CD:+9.6 dBs
10
C236
1
2
3
C212 CCG1192-
A GND 1u/10 USB:+9.7 dBs
0.1u/10
0.1u/10
0.1u/10
R720
NM
CDSRQ
DGND C221
NM
RESET
DGND1
PGND
DATA
CDSTBY
VDD4
SDA
BCLK
C231
SCL
LRCK
C204 1u/10
WAIT
SKIP
NM
C213
C214
C215
PGND DGND C206 1u/10
AGND DGND REFERENCE AREA MAP
R718
R701 C710
220
C233 EVOL 201 - 250 MECHA VD 751 - 800
31 150p/50
47k NM C202 1u/10
29 C211
PGND GND
R702
NM
RCA 251 - 300 GRILL 801 - 850
100k R719 AMP 301 - 400 SWVDD5 851 - 870
40
39
38
37
36
35
34
33
32
30
28
27
26
25
24
23
22
21
100k TUNER 401 - 470 ILMPW 871 - 890
OUTRL
DVDD2
INAN1L
INBN3L
IN5L
DATA
OUTPL
STB
CLK
INAP2L
INBP4L
AGNDL1
AGNDL2
RESETB
BCLK
OUTFL
VREFL
C223
AVDDL1
AVDDL2
DIN
iPod CP 531 - 550 W.REM&MIC 891 - 900
PM9013A
12 AGNDR1
13 AGNDR2
9 AVDDR1
10 AVDDR2
1000p/50
IC201
USB&USB5V 551 - 600 PW CONNECT 901 - 910

1 INAN1R
3 INBN3R
2 INAP2R
4 INBP4R
7 OUTRR
6 OUTPR
OUTFR
11 VREFR
17 DVDD1
20 LRCLK
14 DGND
NM 18 DOUT
C235 19 MCLK
GND
15 TEST
RCA
5 IN5R
CCG1192- CTF1793- 16 REG

AGND DGND UCOM 601 - 670 IC REG 911 - 940
5 4 RESET 671 - 680 ASENS 941 - 950
B
8
FLASH ROM 681 - 690 TELIN 951 - 960 FM: -6.6 dBs
10u
150
L201
150
150
6 3
7 2 NM DSENS 691 - 700 B.REM& 961 - 970 AM: -6.4 dBs RL FL
L202
C224 0.1u/10
NM
C218 47u/16
A.ANT AUX:+9.3 dBs
CCG1192-
C704 CD MECHA 701 - 750
R715
8 1
R716
R717
BT MOD 971 - 990 CD:+10.4 dBs RR FR

10p/50
C210
R703 USB:+10.6 dBs
220
220
100
220
100
C225
0.1u/10
C220
CCG1192-
4.7k C705
C217
1k
C216
150p/50
10u
10p/50 PLch C256 R256 Set back chart
C219
R711
10u
R704 100k C706 CCG1201- 820
ucomD RFGND
DGND
1u/10
4.7u
>
1u/10
GND MUTE
R706
R707
R708
R709
R710
NM
10p/50
1u/10
C702
100p/50
R258
C258
C209 10u
22k
NM
1000p/50
R705 3.0A
C232
C229
C228
CCG1192-
C226
NM
C207 0.1u/10
C208 0.1u/10
NM
NM
L701
1
2
3
P251
NM
NM
RN1910
CEK1386- RCAG
C201
Q252
C234
C203
C205
C703 1 2
R259 PL
6
5
4
NM R721 NM C227 NM
R724
JA251
100p/50
R257
C257
22k
R722 NM NM AGND
NM AGND
USBGND USB GND FR C255 PR CKB1099-
R723 NM PRch CCG1201- 4.7u R255 GND
ROR RR 3
820
PR FL 2
GND FLch C252 R252 1
6 PREOUT
CCG1201- 820
4.7u FR 5
4
100p/50
R254
C254
22k
CDDATAIN
CDLRCKIN
1
2
3
CDSCKIN
RN1910
CDSTBY
CD_SDA
RESETB
CD_SCL
CDWAIT
Q251
CDSKIP
CDSRQ
CDRST
LRCLK
AUXG
TUNR
AUXR
MCLK
DATA
AUXL
TUNL
BCLK
CLK
STB
DIN
C260
C259
C261
0.1u/10
0.01u/10
NM
6
5
4
100p/50
R253
C253
22k
FRch C251 R251 GND
FLASH ROM L681
CCG1201- 820 GND
*2 NM 4.7u
R681
IC681
R684
47k
47k
R685
47k
1 8
The pin number of left side is a number on the PCB (silk printing).
0.1u/10
CS VCC X602 IC301

2 NC/SIO3 7 NM PA2032A
NM
SO/SIO1 16.9344MHz X603

3 SCLK 6 GND1 1
The pin number of right side (in the IC frame) means the pin number of IC itself.
WP/SIO2 1 3 X1 No connection
C683 3p/50
R682
R313 R312
47k
4 5 2 1 2
C681
GND SI/SIO0
C
OFF.DET 1
C682
NM
R683
C619 GND2 C618 NM 3

47k
PEB093A8 2 P-GND2 2
12p/50 3X2 4 12p/50 AMP 4
CSS1794- RL- 3
SYS+B 5.78 V R309
16.9344MHz STBY 5
R624 STBY 4
10k 6
C328
22p/50
NM
1608
DGND 2.2k RL+ 5
7
R301
R311
470
R303
C329
VCC 6
NM
47k
470
L601 VDD3.3V
8
FL- 7
NM GNDTP1 9
R304
R621 C317 P-GND1 8

470
C616
C617
NM
NM
100p/50
R302
8
7
6
5
10
470
C319
AGND GND GND FL+
10u/16 9
47k
C621 0.1u/10
R623
R632
NM
ASEBRK 47k
C318
R622
11 SVR
220
220
220
220
220
220
47k
47k
C620
0.1u/10
10
GND C301 0.22u/16 NM 12
TMS 2
TDI 3
TDO 4
TCK 1
FLIn 11
R631
R630
R629
R628
R627
R626
R625
TRST
C305 0.22u/16 13
VDD1.2V RLIn 12
L602
14
C320
1p/50
NM AGND 13
R620 C307 0.22u/16 GND 15
RRIn 14
C614
C615
NM
NM
C303 0.22u/16 AGND

80
MD_CLK 79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
ASEBRK 62
TRST 61
NM 16
FRIn 15
*3 only A, B AC_GND
TDO
TCK
C613 0.1u/10 C313

TMS
17
QSPCLK
MD_BOOT
QSSL
QIO1
Vss
EVOL_MCK
TDI
C309 NM
NM
NM
NM
QIO3
QIO2
QIO0
Vcc
PVcc
60
AUDIO_X1
C331 NM
C332 NM
C333 NM
C334 NM
AC-GND
Vss
16
AUDIO_X2
R619
C612 1u/16 18
47k
RB751SM-40
59 FR+ 17
C310
C311
C312
100p/50
C321
0.1u/10 R618 GND GND 19
58
D601
C314 0.1u/16 P-GND3 18

R617
10k
MODEL 47k 20
AVref MODELAD 57 FR- 19
GND C901 21
AVcc B.UP
IC601 KEYAD 56 AGND KEYAD VCC 20
AVss MU1 22
R5S726A0D216FP VDSENS 55 VDSENS CCH2040- RR+ 21
R305 R306 GND 2200u/16
*3 ROT1 54 R616 47k
ROT1 GNDTP2
23
MUTE 22
10k 220 24 RR-
R618 R619 ROT0 53 R615 47k ROT0 23
25 P-GND4
A, C CDSKIP 52 CDSKIP
C335 NM
NM 47k 24
1u/10
Q301
R307
C327
ASEMDR614 26
22k
B, D 47k NM ASEMD 51 3 4 H-SW 25

GND
C323
C324
C325
C326
10k 47k MUTE 27
E 47k DP 50 DP 2 5 No connection
DM 49 DM 1 6 R308
10p/50
SW5V
10p/50
10p/50
10p/50
PVcc 48 RN4983
R659
R660
SYS+B
B.UP
NM
15k
15k
3.3V
1.2V
0.1u/10
C611
Vss 47
Vss 46 MUTE Q302
D
GND GND
PVcc
NM
XTAL 45 R613 C608 OFFSET
GND
R612 1.5k
EXTAL 44 12p/50
NM C610
GND JA901
Vcc 43
X2 3
NC1 2
CKM1613-
0.1u/10
>
NMI 42 47k
IC REGULATOR 18
CSS1847-
IC911
12MHz
PLLVcc 41 R611 600uH

X601
BA49183-V12 GND1 GND2 (10A) FUSE

C609 0.1u/10 BSENS 17
Vss 40 BSENS 1 BSENS L901 D901 B.UP3 B.UP1
NC2
YEK5001
16 GND
1 X1
SYSPW R913 SYSPW 2 SYSPW 2 1

RES 39 1SR154-400
CTH1432- 15 B.UP
POWER SUPPLY
22k
4
Vss 38 C607 3 SW5VCNT D902 BREM

+B 14 BREM
CKIO 37 12p/50 4 +B 1SR154-400 GND ACC &A.ANT
C606 13 ACC
SYSB
R610
47k
5 SYS+B
R609
47k
PVcc 36
SW5V 12
0.1u/10 USB GND 6 SW5V
SSENS 35 SSENS
11
RGBDT/DIMMER
DSENS1 R608 VDD

RGBCK/ILMCLR1
RGBCS/ILMCLR2
/CDRST /DSENS 34 DSENS 7 VDD

CDDADATIN TELIN 10
33 NM CDRST 1.2V 8 VDD12
CDLRCKIN
R607 NM 9 TEL
SWVDD 9 SWVDD
CDSCKIN
32 CDDATAIN RR2
CDSTBY
CPPWR
ANTPW
ILMPW
CPRST
R606 NM B.UP2 8 RR-

TELIN
DPDT
BTRX
KYDT
10 +BUP
BTTX
PVcc
RL2
PVcc
31 CDLRCKIN
Vss
Vss
Vss
Vcc
7
Vcc
R914 VDDCNT RL-

RST SWVDD5 11 VDDCONT RR1
IC671 6
22k RL1 RR+
12 GND
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
C673
2p/50
1 5 5
OUT NC2 FR2 RL+
C929
NM
2 D911
C925
NM
4 FR-
SWVDD
VDD CRG03
SYS+B
FL2
C605 0.1u/10
D671
0.1u/10
3 4
R670
C603 0.1u/10
R664 10k
NM
3 FL-
47k
TELIN1
C913 1000p/50
VSS NC1 D912

R912
FR1
R911
C604
C911
0.1u/10
NM
1
NM 2 FR+
R671 FL1
C928
CCG1201-A
1000u/16
R603
S-80827CNMC-B8M CRG03
CCG1201-A
CCG1201-A
CCG1201-A
CCG1201-A
1 FL+
C602
R604
NM
100k
C914
1000p/50
1000p/50
1000p/50
0.1u/16
C915
C912
C927
C926
C924
C923
C922
C921
C920
C919
C918
C916
NM
NM
C917
RFGND
NM
NM
1u/10
NM
C671
C930
NM
C672
4.7u
RESET FM:+20.3 dBs

RGBDT
NM
RFGND GND AM:+20.5 dBs
4.7u
4.7u
4.7u
4.7u
DGND
AUX:+35.3 dBs
NM
GND CD:+35.6 dBs

ASENS
USB:+35.7 dBs
R605
E
LSCR523UB
ASENS2 ASENS1
R941 D941 R944
Q941
RGB Supply
RGBST/ILMCLR2
RGBCK/ILMCLR1
RGBDT/DIMMER
Q871 22k 1k
DZ2J068M0
0.1u/16
2SA1577(QR)
R943
6.8k
R942
C941
47k
CDSCKIN
CDSTBY
OFFSET
ILMPW
CPPWR
R872
CPRST
DPDT
BTRX
KYDT
BTTX
10k
TELIN
GND ASENS
R871
3.3k
(1/10W)
R952 NM
22k TELIN
Q872
Q951
LTC143EUB LSAR523UB
R808 D951
SSENS
R953 L951
2.2k GND
R805 100 AUXL R951 15k BTH1101-
R803 22k
R806 100
R877 NM Q873
2SD1767(QR)
LED Supply TELIN
1k GND
DAN202UM
AUXR
R807 NM
22k 100
R879
R804 AUXG
R873
NM
1.2k
NM
L801 R809 Q874
11 2 2 DP
0.1u/16
3 4 C968
D871
DZ2J075M0
22 CCG1192-A
47k
C969 R310
0.1u/16
2 5 10u
C872
NM
NM
NM
R810 GND GND 0

44 3 3 DM 1 6
C873
R874
RN4983
390
R878
CTF1713- 22 R811 2.2k RGBST/ILMCLR2 ILMPW

D302
C871
R812 2.2k RGBCK/ILMCLR1 NM

R876
D872
D301
C322
0.1u/16
NM
R813 2.2k RGBDT/DIMMER

R875
47k
B.REM&A.ANT
C330
C961
NM
Dim off 12.13 V

R814 2.2k KYDT Q875 Dim on 8.03 V NM
DPDT LTC043EEB
R815
8.2k
ILM GND GND AGND GND

R816 2.2k ROT0
ILMPW
R817 2.2k ROT1
SWVDD
F
VA801 EZJP0V270RM
VA802 EZJP0V270RM
L851 IC801
C809 220p/50
D806 DZ2S068C
D807 DZ2S068C
D808 DZ2S068C
D809 DZ2S068C
C810 220p/50
1 5
NM
NM
NM
0.1u/16
C852
C807 1u/10
DPDT
NM
INB Vcc
R851
2
4.7k
C851
NM
INA
3 4
GND OUTY
D810
D811
0.1u/10
C808
C811
TC7SET08FUS1
GND
A
GND SWVDD
GND
DEH-X66BT/XNUC
5 6 7 8
41
F
E
B
A
D
C
42
A-a A-b
A-b
N701 C707 ROL RL
NM FM: -5.7 dBs
FL
C708
AM: -5.5 dBs
GND
VDD
AUX:+9.3 dBs
10u
1
1
NM
9
C236
TUNER AMP UNIT
10
11 DATA
12 BCLK
13 LRCK
14 GND
15 PGND
16 WAIT
CD:+9.6 dBs A
A GND 1u/10 USB:+9.7 dBs
R720
NM
DGND C221
0.1u/10
0.1u/10
0.1u/10
NM
C204 1u/10
NM
DATA
PGND
C231
BCLK
PGND DGND
DGND1
LRCK
WAIT
C206 1u/10
C212 CCG1192-
C213
C214
C215
AGND DGND REFERENCE AREA MAP
C710
220
EVOL 201 - 250 MECHA VD 751 - 800
R718
NM C202 1u/10 C233
PGND GND
NM
RCA 251 - 300 GRILL 801 - 850
R719 AMP 301 - 400 SWVDD5 851 - 870
40
39
38
37
36
35
34
33
32
31 150p/50
30
29 C211
28
27
26
25
24
23
22
21
100k TUNER 401 - 470 ILMPW 871 - 890
C223
iPod CP 531 - 550 W.REM&MIC 891 - 900
STB
CLK
DIN
IN5L
DATA
BCLK
1000p/50
OUTPL
OUTRL
OUTFL
VREFL
DVDD2
INAN1L
INAP2L
INBN3L
INBP4L
USB&USB5V 551 - 600 PW CONNECT 901 - 910
AGNDL1
AGNDL2
AVDDL1
AVDDL2
RESETB
GND
IC201
AGND DGND UCOM 601 - 670 IC REG 911 - 940 RCA
PM9013A
INAN1R
INAP2R
INBN3R
INBP4R
IN5R
OUTPR
OUTRR
OUTFR
AVDDR1
AVDDR2
VREFR
AGNDR1
AGNDR2
DGND
TEST
REG
DVDD1
DOUT
MCLK
LRCLK
RESET 671 - 680 ASENS 941 - 950
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
18
19
20
L201 FLASH ROM 681 - 690 TELIN 951 - 960 FM: -6.6 dBs
10u
150
150
150
NM DSENS 691 - 700 B.REM& 961 - 970 AM: -6.4 dBs RL FL
NM
C235
A.ANT AUX:+9.3 dBs
NM
C704 CD MECHA 701 - 750
L202
BT MOD 971 - 990 RR FR
CD:+10.4 dBs
R715
10p/50
R716
R717
C705 USB:+10.6 dBs
CCG1192-
C210
C225
C224 0.1u/10
10u
C218 47u/16
C220
C256 R256 Set back chart
C217
PLch
C216
10p/50
0.1u/10
CCG1192- CTF1793- 16
2
2
150p/50
C706 CCG1201-
10u
820
C219
CCG1192-
ucomD RFGND
DGND GND 4.7u MUTE
C702 10p/50
NM
1u/10
1u/10
>
10u
NM
22k
1u/10
3.0A
R258
C258
NM
1
2
3
P251
NM
NM
100p/50
C232
C229
C228
C226
CEK1386- RCAG
NM
L701
1000p/50
C209
C201
C703 Q252 2
C234
C203
1
CCG1192-
C205
RN1910
6
5
4
R721 NM R259 PL
NM C227 NM
C207 0.1u/10
C208 0.1u/10
R722 NM NM AGND JA251
22k
R257
C257
USBGND AGND USB GND FR C255 PR CKB1099-

100p/50
R723 NM PRch CCG1201- 4.7u R255 GND

ROR RR 3
820
PR FL 2
GND FLch C252 R252 1
6 PREOUT
CCG1201- 820
4.7u FR 5
4
1
2
3
22k
R254
C254
100p/50
DEH-X66BT/XNUC
Q251
RN1910
6
5
4
CDDATAIN
CDSCKIN
CDLRCKIN
AUXL
AUXG
TUNL
CDWAIT
TUNR
AUXR
MCLK
LRCLK
BCLK
DIN
DATA
CLK
STB
RESETB
NM
C260
C259
C261
22k
0.1u/10
R253
C253
0.01u/10
FRch C251 R251 GND

100p/50
M L681
NM CCG1201- 820 GND
4.7u
47k
3
3
R685
C X602 IC301
3 7 NM PA2032A
X603
0.1u/10
16.9344MHz
K 6 1 3 GND1 X1 1
No connection
5 2 1 R313 R312 2
0 OFF.DET 1
C619 NM NM
C681
GND2 C618 3
2 P-GND2 2
47k
R683
3X2 4 12p/50 4
C683 3p/50
12p/50 AMP
CSS1794- RL- 3
SYS+B 5.78 V R309
16.9344MHz STBY 5
R624 STBY 4
10k 6
2.2k RL+ 5
NM
DGND
C328
1608
7
VDD3.3V VCC 6
470
NM
L601
47k
R301
470
8
R311
R303
C329
FL- 7
NM GNDTP1 9
R621 C317 P-GND1 8
8
7
6
5
470
NM
NM
GND 10
R304
AGND GND 10u/16 FL+ 9
C616
C617
470
R302
NM
C319
C318
100p/50
11 SVR
10
R623
47k
R622
C301 0.22u/16 NM 12
C620
GND FLIn 11
0.1u/10
C305 0.22u/16 13
TDI 3
TCK 1
TMS 2
TDO 4
VDD1.2V RLIn 12
L602
TRST
ASEBRK 47k
14
NM AGND 13
C307 0.22u/16 GND
C320
R620 15
1p/50
RRIn 14
C303 0.22u/16 AGND
NM
NM
69
68
67
66
65
64
63
NM 16
C614
C615
FRIn 15
C613 0.1u/10 *3 only A, B C313 AC_GND 17
60 AC-GND 16
NM
NM
NM
TCK
TDI
TDO
TMS
TRST 61
C612
PVcc
1u/16 18
4
59 17
4
FR+
47k
R619
ASEBRK 62
QSPCLK
0.1u/10 R618 GND GND 19
58
C309 NM
C314 0.1u/16 P-GND3 18

C310
C311
C312
C331 NM
C332 NM
C333 NM
C334 NM
AUDIO_X1
AUDIO_X2
C321
The pin number of left side is a number on the PCB (silk printing).
47k 20
100p/50
MODEL
D601
10k
MODELAD 57 FR- 19
R617
AVref C901
RB751SM-40
AVcc AGND KEYAD GND B.UP 21
KEYAD 56 VCC 20
AVss MU1 22
VDSENS 55 VDSENS CCH2040- RR+ 21
R305 R306 GND 2200u/16 23
ROT1 54 R616 47k MUTE 22
ROT1 GNDTP2
10k 220
ROT0 53 R615 47k ROT0 24 RR-
23
R618 R619
CDSKIP 25 P-GND4
A, C NM 47k CDSKIP 52 24
ASEMDR614 Q301 26
ASEMD 51 3 4 H-SW 25
The pin number of right side (in the IC frame) means the pin number of IC itself.
B, D 47k
22k
NM
1u/10
GND
R307
C327
10k 47k DP MUTE 2 5 27

E 47k DP 50 No connection
C335 NM
C323
C324
C325
C326
DM 49 DM 1 6 R308
PVcc 48 RN4983 NM
15k
15k
R659
R660
SW5V
B.UP
47
10p/50
3.3V
1.2V
Vss
10p/50
10p/50
10p/50
SYS+B
C611
0.1u/10
Vss 46 GND MUTE GND Q302
KEYAD VCC 20
AVss MU1 22
VDSENS 55 VDSENS CCH2040- RR+ 21
R305 R306 GND 2200u/16 23
ROT1 54 R616 47k MUTE 22
ROT1 GNDTP2
10k 220 24
ROT0 53 R615 47k ROT0 RR- 23
R618 R619
CDSKIP 25 P-GND4
A, C NM 47k CDSKIP 52 24
ASEMDR614 Q301 26
ASEMD 51 3 4 H-SW 25
mber of IC itself.
B, D 47k
22k
NM
1u/10
GND
R307
C327
10k 47k DP MUTE 2 5 27
E 47k DP 50 No connection
C335 NM
C323
C324
C325
C326
DM 49 DM 1 6 R308
PVcc 48 RN4983 NM
15k
15k
R659
R660
SW5V
B.UP
47
10p/50
3.3V
1.2V
Vss
10p/50
10p/50
10p/50
SYS+B
C611
0.1u/10
Vss 46 GND MUTE GND Q302
NM
XTAL 45 R613 C608 OFFSET
PVcc
GND
R612 1.5k
EXTAL 44 12p/50
GND JA901
NM C610
Vcc 43 CKM1613-
0.1u/10
X2 3
NMI 42 47k
5
5
NC1 2
IC REGULATOR IC911 18 >
PLLVcc 41 R611 BA49183-V12 600uH GND1 GND2 (10A)
BSENS 17 FUSE
C609 0.1u/10
X601
Vss 40 BSENS 1 BSENS L901 D901 B.UP3 B.UP1 YEK5001
12MHz
CSS1847-
R913 SYSPW 2 1 16 GND
NC2
RES 39 SYSPW 2 SYSPW 1SR154-400
CTH1432- 15 B.UP
4
1 X1
22k D902 BREM
Vss 38 C607 3 SW5VCNT
+B 14 BREM
CKIO 37 12p/50 4 +B 1SR154-400 GND ACC &A.ANT
C606 13 ACC
PVcc 36 SYSB 5 SYS+B
47k
47k
12
R610
SW5V
R609
SSENS 35 0.1u/10 USB GND SSENS 6 SW5V
DSENS1 R608 11
/CDRST DSENS VDD
/DSENS 34 7 VDD
TELIN
CDDADATIN 10
33 NM CDRST 1.2V
CDLRCKIN 8 VDD12
R607 NM 9 TEL
32 CDDATAIN SWVDD 9 SWVDD RR2
R606 NM B.UP2 8 RR-
31 CDLRCKIN 10 +BUP RL2
RGBDT/DIMMER
R914 VDDCNT 7 RL-
PVcc
Vss
KYDT
DPDT
CPRST
CPPWR
TELIN
CDSTBY
SWVDD5
CDSCKIN
RST 11 VDDCONT RR1
IC671 6
22k RL1 RR+
22
23
24
25
26
27
28
29
30
12 GND
1 5 5 RL+
POWER SUPPLY
OUT NC2 FR2
C673
2p/50
2 D911
NM
4 FR-
C929
VDD CRG03
NM
FL2
C925
D671 3 4 3
VSS NC1 FL-
NM
D912 FR1
1
1
SWVDD
SYS+B
R670
NM 2
NM
FR+
R912
R911
R671
C911
FL1
TELIN1
S-80827CNMC-B8M CRG03 1
100k FL+
C928
NM
C605 0.1u/10
RFGND
NM
NM
C930
R604
C914
NM
NM
NM
C915
C912
NM
C927
C926
C924
C923
C922
C921
C920
C919
C918
C916
1000u/16
C917
0.1u/16
C671
1u/10
C672
C913 1000p/50
1000p/50
CCG1201-A
FM:+20.3 dBs
1000p/50
1000p/50
6
6
RESET NM
4.7u
CCG1201-A
CCG1201-A
CCG1201-A
CCG1201-A
RFGND GND AM:+20.5 dBs
4.7u
4.7u
4.7u
4.7u
DGND
AUX:+35.3 dBs
NM
GND CD:+35.6 dBs
ASENS
USB:+35.7 dBs
R605
ASENS2 ASENS1
R941 D941 R944
RGB Supply
Q941
Q871 22k 1k
DZ2J068M0
2SA1577(QR)
LSCR523UB
6.8k
47k
R943
R942
C941
0.1u/16
10k
R872
KYDT
DPDT
CPRST
CPPWR
TELIN
CDSTBY
CDSCKIN
GND ASENS
R871
3.3k
(1/10W)
R952 NM
22k TELIN
Q872
Q951
LTC143EUB LSAR523UB
DEH-X66BT/XNUC
R808 D951
SSENS
R953 L951
2.2k GND
AUXL R951 15k BTH1101-
R877 Q873 LED Supply TELIN
NM 2SD1767(QR) DAN202UM
1k GND
AUXR
7
7
NM
AUXG
NM
NM
1.2k
R879
Q874
R873
L801 2 2 R809 DP
3 4 C968
22 CCG1192-A
47k
C969 10u R310
D871
2 5
0.1u/16
NM
NM
R810 DM GND GND 0
C872
NM
3 3 1 6
0.1u/16
R811 RGBST/ILMCLR2 RN4983 ILMPW
DZ2J075M0
CTF1713- 22 2.2k
C873
390
R874
D302
R878
R812 2.2k RGBCK/ILMCLR1 NM
C871
NM
RGBDT/DIMMER
R876
D872
D301
R813 2.2k
C322
47k
B.REM&A.ANT
0.1u/16
R875
Dim off 12.13 V C330
NM
R814 2.2k KYDT Q875

C961
Dim on 8.03 V NM
DPDT LTC043EEB
ILM GND
8.2k
GND GND
R815
R816 2.2k ROT0 AGND
ILMPW
R817 2.2k ROT1
SWVDD
L851 IC801
NM DPDT 1 5
NM
INB Vcc
NM
220p/50
2
C852
INA
NM
4.7k
EZJP0V270RM
R851
3 4
C851
GND OUTY
C810 220p/50
C809
D811
8
8
C811
TC7SET08FUS1
VA802 EZJP0V270RM
0.1u/10
GND
GND SWVDD
GND
A-a A-b
A-b
43
E
A
D
C
F
B
F
E
B
A
D
C
44
A-a A-b
A-b
A-a
C457 4700p/25 TUNR CN701
*1 C456 4700p/25 TUNL
*1 No SW SW Model
CD C
TUNER
CN701
VD
VD
GND
A, B, D C, E
/CDSRQ
SDA
VDD
FM/AM ANTENNA AGND
C464
1u/6.3
VKN1192-
1
1
1
2
3
4 /CDSTBY
5 SCL
6 SKIP
7
8 RESET
9
JA401 FM: -14.7 dBs C419 NM 15p/50
10
11 DATA
12 BCLK
13 LRCK
14 GND
15 PGND
16 WAIT
X401
9p/50
YKS5041- AGND MECHA VD
C449
AM: -14.5 dBs 36.48MHz *1
C450
9p/50
TUNGND C420 NM 0.01u/16
L420
2 1 X2
L419
CTF1786-
4 GND2 3 C421 3p/50 NM
DCH1246
NM
CTF1786-
3 DGND 7.4V
KN2 1 2 C423 NM 8p/50
SDA
VD2
SCL
Q751
DATA
PGND
NM
M2R6TP_GND R416 NM
VDD4
BCLK
GND1
RESET
P
P402
CDSRQ
DGND1
P401
SKIP
LRCK
WAIT
X1 100p/50 22p/50 KTD2092 VD1
C453
C428
NM
C446
C448 0.1u/10
CDSTBY
C445 0.1u/10
C447 1u/10
CSS1848-
0.1u/10
C709
C455
C452
1u/10
0.22u/16 C432 82p/50 2p/50 R701
HSPC16701B02
L418 NM
220
R718
L417 C435 0.47u/10 1u/10 47k
47k
C454 NM R702
R753
RFGND
NM
L416
R417
C439 NM 0.1u/16
C753
NM NM 100k R71
C451
0.1u/10
R415
390
0 C459 100p/50 1000p/50
1/4
R752
C751 NM
L414 L415 100
NM
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
*1 VDCONT Q752
C447 1u/10 NM
C467 NM
1 48 0.1u/10 C448 0.1u/10 0.01u/16 3 4
CCG1201-A-T 10u/10
220
750
R401
R402
TCFM
2 C444 2 5 GND
TVDAC
PLLTEST
47 2.2u C467 NM 0.1u/10
OSCIN
10k
R754
OSCOUT
CCG1218- 1 6
0.1u/10
3
GND-PLL
VCC-PLL
DACOUTR
DACOUTL
VREFDEC
GND-REF
VCC-REF
46 C443 L405 68n NM RN4983
VDDIO1V2
C401 FMMIXDEC 5 4
VDDPLL1V2
RFGND 0.1u/10 4
D402
D401
45 NM L406 CTF1389 NM
L401 FMMIXIN2 3
VCC-ADC_DAC
GND-ADC_DAC
6
D751
RN731VN
150
C410
150
150
RN731VN
0.27u 5 TEST 44
C752
L407 NM 0.27uH
DZ2J082M0
FMMIXIN1 FMPINDRV VDD_CORE 7 2
33p/50 C402 6 FMPINDDEC GND1V2 43
0.01u/16 GNDRF L408 4.7uH 1.5uH 8 1 C704
C403 GPIO0
7 42
NM
GPIO1 NM 0.39uH
R715
L409 10p/5
R716
TCAM
R717
6p/50
C409
C408
C407
C406
C405
L402
1u/10 GPIO2 R703
0.15u
8 41
0.01u/16
0.01u/16
0.01u/16
GND 4.7k C705
220
220
100
220
100
VCCRF L410 47uH 2.2uH

1k
AGND IC401 GPIO3

orRFGND C404 NM 9 GPIO4 40
CK_SEL TDA7706 R403 390 330 10p/5
2
2
10 GPIO5 39
RF GND
R704 100k C706
GNDVCO GPIO6 R408 470
R711
360
L403 11 38
C412 LFREF GPIO7 C702 10p/5
CTF1786-
R409 NM 0
0.1u/10 C411
R706
R707
R708
R709
R710
12 37 R705
LF1 GPIO8 R411 680 390 NM
0.01u/16 13 36 C701
C413
PINDDEC NM
NM
A GND VCCVCO GND3V3

L701
C445 0.1u/10 NM
0.1u/10
C414 0.01u/16 14 PINDIN 35 C442
*1 TCAM2 VDD3V3 0.01u/16 C703
L404 RFGND 0.1u/10 C465 NM 0.01u/16
C415 CCG1192- 15 34 TUN_SCL R721
I2CSCL R724 NM
CTF1786- 10u DGND C466 NM 1u/10
VREG3V3
RSTN
RDSINT
16 I2CSDA 33 TUN_SDA R722
RFGND C468 NM 1u/10 NM
GNDLNA
LNAIN
LNADEC
LNAOUT
LNAIN2
LNAOUT2
LNADEC2
AMMIXIN1
AMMIXIN2
GNDSLINK
VDIG
VCCREG1V2
REG1V2
C417
NM
0.1u/10
C461
C416
C418
0.1u/10
0.022u/16 C464 DCH1246 GND R723
NM
L413
17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
GND
C419 15p/50 R403 C424 C461 0.01u/10 NM
CTF1786-
C420
NM 24
RFGND TUN_RST
0.01u/16 390
NM
L406 0.01u/16 SW B.UP
*1
C427
C426
C425
NM
CTF1389
0.1u/10
L408 GND
0.1u/10
CCG1192- SW5V
R409 0
L405 4.7u
C460
10u
1M
L407
NM
R404
68n 3.3V
R410
C430
C438
1u/10
0.27u
C468
C440
C439
C436
1M
33
0.1u/16
C437 NM
C423
8p/50
R407
1000p/50
1000p/50
RFGND
DEH-X66BT/XNUC
*1
NM
C422
C431 NM DGND *1 *1
R412 R413
L409
0.39u
VDSENS
VDCONT
CDSRQ
CDSTBY
CD_SCL
CDSKIP
CD_SDA
CDRST
CDDATAIN
CDSCKIN
CDLRCKIN
CDWAIT
470
*1
C428
R406
R408
C421
3p/50
100p/50
1/4W 8.2 8.2 1/4W
DGND
C463
C441
FLASH ROM L681
NM
L411 NM
10p/50
NM
R405
MCLK
C429 L410 *2
680
0 NM
NM
R411
BSENS
ASENS
R414
C432
IC681
C435
82p/50
RF GND
RESETB
VDCONT
CDWAIT
0.01u/16 *2
C434
47u
47k
0.47u/10
TUN_RST
C466 1u/10 IC681

47k
0.01u/16
R681
C459
R684
47k
3
3
C465 C433 *1 100p/50 1 8

R685
*1 C462 RF GND RF GND *1 A, B PEB093A8 CSVCC

*1
C458 1000p/50 2 NC/SIO3 7
NM RFGND DGND NM RFGND DGND C, D, E PEB089A8 SO/SIO1
0.1u/10
1
NM
AGND RF GND DGND GND DGND AGND 3 SCLK 6

WP/SIO2
4 5
GND SI/SIO0
47k
R682
C681
PEB093A8
C682
47k
KN1
R683
C683 3p/50
M2R6TP_GND
CN971
VKN1192- BT Connector
VCC 16
DGND
47k
C625
NM
R638
C622
VCC 15
22p/50
0.1u/10
C971
GND 14 C973
47p/50
GND 13 R974 100
8
7
6
5
BTDATA R636
BTDATA 12
R975 100 BT_BCK
47k
BTBCK 11 47k
R623
220
220
220
R632
100
47k
220
220
220
R976 100 BT_LRCK R637

C620
BTLRCK 10
L971
0.1u/10
C624
C623 0.1u/10
R635 1k
R634 1k
TDI 3
47k
TCK 1
TMS 2
TDO 4
GND 9
0.1u/10
R633
R631
NM
R630
R629
R628
R627
R626
R625
C621 0.1u/10
ASEBRK 47k
D BT_RST
NRST_CPU 8
BTTX
SYSTOBT 7
CN23 R971 NM BTRX
90
89
88
87
86
85
84
83
82
81
80
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
BTTOSYS 6
4.7k
4.7k
R640
R639
GND 5 R972 NM CP_SCL 91
NM
Vss
TCK
TDI
TDO
Vss
Vcc
TMS
Vcc
Vss
C972
QIO1
TRST 61
QIO3
QIO2
QIO0
QSSL
PVcc
92
PVcc
4
MIC1P CP_SDA
4
ASEBRK 62
/ASENS
TUNRES
VDCONT
MD_CLK 79
QSPCLK
R641
/BSENS
GND 3 TUN_SCL 93
/CDWAIT
MD_BOOT
GND
AUDIO_X1
R973 NM
EVOL_MCK
AUDIO_X2
EVOL_RST
R642
MIC1N 2 TUN_SDA NM 94 MODE
2.2k TUN_SDA CP_SCL AVref
C974
GND 1 CD_SCL NM 95 CD_SCL CP_SDA IC601 AVcc KE
96 TUN_SCL AVss
GND GND CD_SDA CD_SDA R5S726A0D216FP VDS
GND
MIC1P
MIC1N
CDSRQ 97 /CDSRQ *3 R
JA892 TESTIN 98 DDON R
YKS5035-
R618 R619
47k
47k
R643 99
R669
R668
TESTIN A, C NM 47k CDS

(RMIC) 6 MIC1P DDON
5 100k 100
MIC1N Vss B, D 47k NM AS
4 Q601
W.REM LTC014YEB C626 101 PVcc
3 E 10k 47k
2 0.1u/10
1 KEYD 102 BT_TESTMD
C627 22p/50
&MIC (W/R) 1 R891 KEYD2 BT_TESTMD
1k KEYD BCLK R644 100 103 EVOL_BCK P
3
NM
KEYAD2
NM
KEYAD KEYAD 22p/50
C894
2 LRCLK
C893
R645 100 104
VA891
EVOL_LRCK
R893
R892 1k C628
1000p/50
1000p/50
VA892 NM
105 KEYD
/16
892
16
JA891
C891
only A B
CD_SCL CP_SDA IC601 KE
96 TUN_SCL AVss
GND GND CD_SDA CD_SDA R5S726A0D216FP VDS
GND
MIC1P
MIC1N
CDSRQ 97 /CDSRQ *3 R
JA892 TESTIN 98 DDON R
YKS5035-
R618 R619
47k
47k
R643 99
R669
R668
TESTIN A, C NM 47k CDS
(RMIC) 6 MIC1P DDON
5 100k 100
MIC1N Vss B, D 47k NM AS
4 Q601
W.REM LTC014YEB C626 101 PVcc
3 E 10k 47k
2 0.1u/10
1 KEYD 102 BT_TESTMD
C627 22p/50
&MIC (W/R) 1 R891 KEYD2 BT_TESTMD
1k KEYD BCLK R644 100 103 EVOL_BCK P
3
NM
KEYAD2
NM
KEYAD KEYAD 22p/50
C894
2 LRCLK
C893
R645 100 104
VA891
EVOL_LRCK
R893
R892 1k C628
1000p/50
1000p/50
VA892 NM
JA891 105 KEYD
C891
C892
GND
only A, BD602
NM 106
0.1u/16
EVOL_DATA
10k
0.1u/16
RB551VM-30
R646
KEYD 107 EX
DIN R647 Vss
100
GND CLK 108 EVOL_CK
Q531 R648 1k C629 109
L531 LSAR523UB
5
Vcc
5
C631
1k 0.1u/10 110
22p/50
NM DATA R649 EVOL_DT PLL
R536 4.7k CPPWR STB R650 1k 111
R540 EVOL_CS
C630 112
47k
PVcc
R531
C531
NM
0.1u/10
CP_SCL
2.2k
SWVDD5 0.1u/10 113
R533
R532
2.2k
R537 100 SWVDD
R539 CP_SDA 114 Vss C
R538 100 PCL
NM 115 PCL P
CPRST RAM_MON 116
RAM_MON SS
IC531 SYNC
R651 47k
USB5V MUTE 117 MUTE USBCTL /CDRST /DSE
337S3959 CMS03 CDDADATIN
L551 USB&USB5V /USBFLG
4.7u
C553 D551 R652
3.3V
B.UP
SYNC SYNC 118 CDLRCKIN
1 8 CTH1524- 0.01u/16
R534 2.7k
GND PAD VCC USBCTL 2.2k 119
2 9 7
SDA RST 120
NM
IC551 FLG
C552
C551
3 6
C565
RGBDT/DIMMER
1u/16
C570
4.7u
Vss
BD9876EFJ
220u/16
PVcc
SYSPW
ILMPW
BTDATA
NM
BT_LRCK
PVcc
RGBCK/ILMCLR1
ROM
Vss
Vcc
RGBCS/ILMCLR2
Vss
BTRX
BTTX
KYDT
DPDT
ANTPW
CPRST
CPPWR
TELIN
0
CDSTBY
CDSCKIN
Vcc
BT_TESTIN
NC1 SCL
CCG1222-
4 5
470
D552
R535 4.7k
R552
R653
NM
1u/10
1
2 BTRST
3 PVcc
4 BT_BCK
6
7
8
9
1 8
R661
220u/6.3
NM
NC2 NC3 Lx VCC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RB056L-40
C532
LX VCC
2 7
C555
10k
0.1u/10
GND 9 BST GND
C558
TP1
GND BST
NM
6800p/25
C633
3 6 BTTESTIN
R555
DDON
C557
GND
C556
C554
VC EN
ROM
VC FIN EN
4 5
R553
C564 CCG1201-
SYNC
180k D
NM
R551
FB SYNC
47k
6.8k
R670
FB SYNC
47k
0.1u/10
R601
47k
C604
C601
R602
TELIN1
NM
0.1u/10
0.1u/10
R664 10k
iPod CP@(2.0C)
C563
R603
NM
C605 0.1u/10
C602
C603 0.1u/10
R604
GND
43k D
R554
GND GND
IC552
6
6
BD2232G-G
GND
RGBDT
1 5
NM
VIN VOUT D GND

R662
NM
2
GND FLG
3 4 FLG
EN OC
NM
R663
NM
C562
C561
R605
1u/10
USBCLT
C569 NM
NM
C560
C559
1u/10
USBCTL
DGND
GND
SYSPW
RGBST/ILMCLR2
BT_RST
BT_BCK
BTDATA
RGBCK/ILMCLR1
BTRX
BTTX
ILMPW
KYDT
DPDT
RGBDT/DIMMER
BT_LRCK
OFFSET
CPRST
CPPWR
TELIN
CDSTBY
CDSCKIN
VBUS
DSENS
C801
2.2k
R802
CN801
DEH-X66BT/XNUC
CKS6452- 220p/50 J R808
RGBDT/DIMMER
DSENS 20 2.2k
R801 2.2k R805 100
AUXL 19 GND R803 22k
SOURCE 18 R806 100
7
7
NOTE : 22k R807 100

AUXR 17 R804
Symbol indicates a resistor. AUXGND 16 L801 R809
11 2 2
No differentiation is made between chip resistors and DP 15 22
RGBST/ILMCLR2 14
discrete resistors. 44 3 3 R810
DM 13 R
Symbol indicates a capacitor. CTF1713- 22
RGBCK/ILMCLR1 12
US5V R
No differentiation is made between chip capacitors and B USB5V 11
R813 2.2k
DPDT 10
discrete capacitors. CN1931 USBGND 9
R814 2.2k
NM
KYDT 8
R818
A DEH-X66BT/XNUC RGBDT 7
The > mark found on some component parts indicates R816 2.2k
ROT0 6
the importance of the safety factor of the part. B DEH-X6600BT/XNUC ILM+B 5
R817 2.2k
Therefore, when replacing, be sure to use parts of ROT1 4
C DEH-X6650BT/XNGS
SWVDD 3
identical designation. D DEH-X6650BT/XNCS 2
ILMGND DGND
NM
NM
ILMG
NM
NM
NM
1 C803
NM
DGND
D801
NM
220p/50
E DEH-X6690BT/XNID
0.1u/16
DZ2S068C
C802
NM : No Mount USGND C804

NM
C814
C810 220p/50
C813
C809
C805
C807 1u/10
D803 DZ2S068C
D804 DZ2S068C
C806 0.1u/16
D802 DZ2S068C
D805 DZ2S068C
D807 DZ2S068C
D809 DZ2S068C
D810
D811
8
D806 DZ2S068C
C808
D808 DZ2S068C
8
VA801 EZJP0V270RM
VA802 EZJP0V270RM
GRILLE
DGND USBGND ILM GND
A-a A-b
A-a
A-b
45
E
A
D
C
F
B
F
E
B
A
D
C
46
B
SEG43
SEG42
SEG41
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
1 SEG0
SEG0 2 SEG1
SEG1 3 SEG2
SEG2 4 SEG3
SEG3
1
1
5 SEG4
SEG4 6 SEG5
SEG5 7 SEG6
SEG6 8 SEG7
SEG7 9 SEG8
SEG8 10 SEG9
SEG9 11 SEG10
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
SEG10 12 SEG11
SEG11 13 SEG12
SEG12 14 SEG13 SEG44 S18 SEG18
SEG13 SEG14
S43
S42
S41
S40
S39
S38
S37
S36
S35
S34
S33
S32
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
SEG14 15 51 25
16 SEG15 SEG45 S17 SEG17
SEG15 17 SEG16 S44
SEG16 SEG17 SEG46 52 24 SEG16
SEG17 18 S45 S16
19 SEG18
SEG18 SEG19 SEG47 53 S46 23 SEG15
SEG19 20 S15
21 SEG20
SEG21 22 S47 S14
23 SEG22
SEG23 24 S48 S13
25 SEG24
SEG25 26 S49 S12
27 SEG26
SEG27 28 S50 S11
29 SEG28
SEG29 30 S51 S10
31 SEG30
10.2 KEYBOARD UNIT

SEG31 32 S52 S9
SEG32
SEGMENT LCD
SEG32 33 60 16
34 SEG33 SEG54 S53 S8 SEG8
SEG33 35 SEG34
SEG35 36 S54 S7/P17
37 SEG36
SEG37 38 S55 S6/P16
39 SEG38
IC1802
SEG38 63 13
V1802
40 SEG39 SEG57 S56 SEG5
PDC202B
SEG39 SEG40 S5/P15
41
2
2
SEG40 64 12
CAW2041-
42 SEG41 SEG58 S57 S4/P14 SEG4
SEG41 43 SEG42
SEG43 44 S58 S3/P13
45 SEG44
GRILLE uCON
SEG45 46 S59 S2/P12

47 SEG46
SEG47 48 S60 S1/P11
49 SEG48
SEG49 50 S61 S0/P10
51 SEG50
SEG50 SEG51 SEG63 69 7
SEG51 52 S62 VDD1
53 SEG52
SEG53 54 S63 CF2
55 SEG54
C1804

SEG55 56 S64 CF1
57 SEG56
SEG57 58 S65 VSS1
59 SEG58
1u/10

SEG59 60 S66 XT1
SEG60
X1801
SEG60 61 74 S67 2
SEG61 SEG68
V3
S69
S70
S71
62
V2
V1
RES
S72
S73
SEG61
UTX/P34
P00
P03
P70/INT0/T0LCP
SEG62 S68
P71/INT1/T0HCP
P01
P02
P04
P05
URX/P35
63
RMIN/P73/INT/T0IN
SEG62 SEG63 75 1
SEG63 64
65 SEG64
76
77
78
79
80
COM0 81
COM1 82
COM2 83
COM3 84
85
86
87
88
89
90
91
92
93
94
95
P06 96
P07 97
98
99
SEG64 66 SEG65
100
SEG65 67 SEG66
DEH-X66BT/XNUC
SEG66
DGND
SEG67
5MHz
SEG67 68
SEG68
CSS1547-
SEG68 69
70 SEG69 D1801
SEG69 COM0
C1803
C1801
C1802
R1809
COM0 71
72 COM1
RGB
COM1 73 COM2 NM
COM2 74 COM3
COM3 C1805 R1810
47k
ILMGND
DGND
0.1u/10
0.1u/10
0.1u/10
0.1u/10 10k
3
3
SEG69
KST0
KST1
KST2
KST3
KDT0
KDT1
KDT2
KDT3
C1856
KYDT
NM
DPDT
COM0
COM1
COM2
COM3
Q1857 DGND
SMLVN6RGB2UK(B) R1863 R1862
LSCR523UB
1 6 NM 68 R1856
B
2 5 100
R
R1865 R1864 Q1858
3 4
LSCR523UB
G
NM 68 R1857
KST3
KST2
KST1
KST0
D1882 100
SOURCE
4
4
4
4
3
3
3
3
C1857 NM R1867 R1866 Q1859

LSCR523UB
2
C1858 NM NM 68 R1858
S1838
S1834
S1826
S1821
CSG1155-
CSG1155-
CSG1155-
CSG1155-
2
2
2
2
1
1
1
1
100
LEFT
NM
DISP
NM
R1942
PHONE
R1941
KDT0
HN1C01FU(YGR)
R1854
1 8 REM
C1859 4 3 1
4
4
4
4
4
NM
3
3
3
3
3
2 7 GND
2 C1941 2
DGND
IC1941
10u
PNJ4833M
3 6
3
VCC
6
SMLVN6RGB2UK(B)
S1839
S1835
S1828
S1842
S1822
5 3
CSG1155-
CCG1192-A
CSG1155-
CSG1155-
CSG1155-
CSG1155-
4 5
2
2
2
2
2
1
1
1
1
1
RED Key
LIST
1 6 6 1 R1943
EJECT
B
1k KDT1
SOURCE
2 5 Q1851
DGND
NM
R
3 4
4
4
G
100
GREEN Key
4
4
4
R1944
3
3
3
REMOTE
D1883
BLUE Key
4
C1860
1
NM
S1840
S1836
S1823
KEY MATRIX
CSG1155-
2
2
2
CSG1155-
CSG1155-
1
1
1
C1861 NM
RIGHT
KDT2
4
4
4
3
3
3
C1862 NM
5
S1837
S1832
S1824
CSG1155-
CSG1155-
2
2
2
HN1C01FU(YGR)
CSG1155-
1
1
1
SMLVN6RGB2UK(B)
BACK
DGND
BAND
KDT3
1 6 4 3 IC1851
B
1u/10
14
0.01u/16
C1854
C1855
2 5 2 1 AO1
R
VSS
3 4 5 2 AO2 13
MU
G
VFS
12
5 6 7 8
KDT3
A
4
S1824
2
REFERENEC AREA MAP
B KEYBOARD UNIT
GRILLE uCON & LCD :1801-1820
3 1
KEY MATRIX&ROTARY :1821-1850
CSG1155- RGB :1851-1910
BAND USB :1911-1920
AUX :1921-1930
S1832
CONNECTOR :1931-1940
4 2 REMOTE :1941-1950
3 1
SOURCE
CSG1155-
KYDT
BACK DPDT
S1837
4 2
3 1
B
D1932
D1931
NM
CSG1155- NM
5
DGND DGND
SWVDD
R1824
R1825
NM
S1830
27k
5 2 CN1931
CKS6451
3
DGND 1
4 1
ILMGND 2
L1931 SWVDD
CSD1168-A 3
DGND
NM ROT1 4
MULTI-CONTROL ILM+B ILM+B 5
ROT0 6
R1851 2.2k RGBDT 7
R1931 KYDT 8
R1852 2.2k
C
C1855
1u/10
R1853 2.2k R1932
2.2k USBGND
DPDT
9
10
A
2.2k
C1854 USB5V
RGBCK 12
11
CN801
0.01u/16
DM 13
RGBST 14
14
13
12
11
10
9
8
DGND DP 15
VDD
C1851
C1853
C1852
CSB
NM
NM
NM
VSS
NC2
VFS
CLK
DI
AUXGND 16
BH2228FV
AUX:+2.0 dBs
IC1851
AUXR 17
1 AO1
2 AO2
3 AO3
4 AO4
5 AO5
6 AO6
7 NC1
SOURCE 18
DGND
AUXL 19
DSENS 20
3
2
BLUE LCD
USB DGND
NM
GREEN LCD
CN1911
L1911
RED LCD
8
7
6
5
CKS6443-
R1855
1k
1
4
1 D
2
3
4
1
2
3
2
2
3
3
1
4
HN1C01FU(YGR)
HN1C01FU(YGR)
5
Q1852
Q1853
D1912
D1911
NM
NM
6
0.1u/16
C1913
C1911
NM
4
C1912
5
5
6
CTF1389-A
CTF1389-A
CTF1389-A
R1921
R1922
R1923
L1921
L1922
L1923
0.1u/16
NM
NM
NM
ILMGND DGND
C1914
NM
ILMGND DGND
C1915
R1859
R1860
R1861
100
100
100
LSCR523UB
LSCR523UB
NM
LSCR523UB
ILMGND DGND AUX

Q1866
Q1867
Q1868
JA1921
YKN5006-A E
3
R1872
R1868
R1870
2
68
68
68
1
C1921
C1922
NM
NM
NM
NM
R1869
R1871
R1873
NM
NM
C1923
D1923
NM
ILMGND
SMLVN6RGB2UK(B)
SMLVN6RGB2UK(B)
SMLVN6RGB2UK(B)
NM
NM
NM
NM
NM
6
5
4
6
5
4
6
5
4
NM
NM
NM
NM
D1885
D1886
D1884
C1862
C1863
C1865
C1866
C1867
C1864
C1870
C1869
C1868
1
2
3
1
2
3
1
2
3
B R G B R G B R G
B
DEH-X66BT/XNUC
5 6 7 8
47
1 2 3 4
10.3 CD CORE UNIT (S11.6VA)
A PU UNIT(P11)(SERVICE)
CXX4754 V3R3
R101 R102 R103
2.7
(1/10W)
(1/10SR,1608)
PUEN
2.4
4.7u/6.3
C104
Q102
(2125)
Vref
LTA123JUB
VCC
2.4
R111
R110 NM LD_CURRENT
LD1 NM
LD Q101 R109 LD
VR
C214
D2
2SA1577(QR) 1.5k
C102
D101
NM
NM
D5
C101
R108
NM
1M
BD B
15 15 ASY
E F
14 14 EFM
D4
VR
B Vc
13 13
C
ATEST
C201
NM
12 12
MD PD PD
11 11
D1
LD+
0.01u/16
C110
0.1u/10
10 10
C111
GND
9 9
VREF 76
D3 8 8 C221 A.Vdd1
VCC V+3A 77
7 7 0.1u/10 A.GND1
F
6 6
E
f C216
1500p/50
78
79
RFI
AC A
5 5 RFAGC AGCO
TOM TOM C220 80
HOLOGRAM UNIT 4 4
C219
C3T
FOM FOM 0.1u/10 81
3 3 AGCI
FOP FOP RFO 0.1u/10 82
2 2 RFO
FOCUS ACT C228 R229 83
R218 R217
TOP TOP
5.6k
1 1 EQ2
C218
TRK ACT
5p/50
18p/50 470 84
EQ1
C217 R216 85
4.7k
C205 RF2-
39p/50 1k 86
TOM
FOM
FOP
TOP
1u/10 RF-
F.ACT: Applying positive voltage to FOP, (1608) 87
A
B
E
F
A.GND2
the lens approaches DISC. C204 88
T.ACT: Applying positive voltage to TOP,
CN101 NM
C222
0.1u/10 89
A.Vdd2
CKS4808-A A
A
the lens moves outer circumference of DISC. B 90
C F 91
B
F
E 92
E
REFO1 REFO 93
C229 REFOU
Land for manual soldering REFO2 d C223 94
0.1u/10 FE-
C236 68p/50 95
FE FEO
C 0.1u/10 C 96
C
1608:PARTS c C224
47p/50
97
98
TE-
C205 C209 C238 TE TEO
C225 99
C307 C308 TE2
C708 TEC 0.01u/16 100
TEC
R101 R102 R103
R246
C239
NM
M1 2125:PARTS
SPDL MOTOR C104
LD
CXE2273
PD
BLK
SOM
Parts with Polarity
D IC201 IC301
D101 VDD
RED
SOP Q101 Q102 Q201
M2 C301
LOAD/CRG MOTOR
GND
BL
LCOM
YW
LCOP
CXC4026
7 CN702
C307 IC301 NM
1u/10
(1608) 1
BD8223EFV
SPIN 28 SIN
8 MD
POWVCC
SOM 2 SLIN 27 CIN SD
SPO-
HOME 3 HOME
SOP 3
SPO+
BIAS 26
FIN
C315
NM
a9
S901 LCOM C312
NM
4
SLLDO-
TKIN 25 FD
5
431
HOME LCOP 5 FCIN 24 TIN TD

E
2
SLLDO+
CSN1080-A 6 CNT 23
POWGND CLCONT
S905 8SNS 7 22
NM FOP LDIN
4
431
8SNS 29
TKO- GND LOEJ
2
FOM 8 21
TKO+ MUTE CONT
S903 1 DSCSNS TOM 9
FCO-
PRTOUT 20
43 1
DSCSNS TOP 10 PREGND 19

2
C308 FCO+
CSN1081-A 1u/10 11 PRTLIM 18 R309 47k
(1608) TKRNF
DSCSNS 12
13
FCRNF
PRTF 17 MOTOR DRIVER LOGIC TABLE
PRTT 16 LOAD EJ PLAY OFF
TKCDET
14 PREVCC 15
FCCDET CLCONT H H L L
0.1u/10
C306
LOEJ H L - -
SWITCHES:
NM
NM
CONT L L H L
CD CORE UNIT(S11.6VA)
C314
C313
S901:HOME SWITCH.........ON-OFF VD
S903:DSCSNS SWITCH.....ON-OFF
C301
NM
PGND
The underlined indicates the switch position.

CLCONT
CONT
LOEJ
C
DEH-X66BT/XNUC
48
1 2 3 4
5 6 7 8
MD
R305 SD
PUEN
TD
FD
C
LD_CURRENT
CD CORE UNIT(S11.6VA)
R307
1k
1k
C302
C303 1000p/50
1000p/50 PUEN
C304
R304
R303
C305 0.022u/16
12k
12k
0.1u/10
R308
R306
4.7k
4.7k
R310
TEMP
/CDSRQ
SKIP
R311 4.7k
R312 4.7k
R313 4.7k
4.7k GND
0.047u/16
3300p/50
0.1u/10
C214
C213
C212
R246
C235
NM
NM
(1608)
VDD TEMP
TEMP
R215
e
LD_CURRENT
NM
MDY
R260
FDY
TH201
TDY
10k
C250
39k
NM
0.1u/10
R214
b
10k
ADENA
MONI2
MONI1
MONI0
C16M
ASY
C215
MDX
TDX
FDX
EFM TESTIN
GND
ATEST
LRCK0
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
MD
EFM
SD
TEMP
VDCONT
TD
FD
ASY
SD2
TEST
/CDSRQ
AD.GND
ATEST
/ADENA
LD_CURRENT
SKIP
/PUEN
AD.Vdd
IO.GND2
/TESTIN
IO.Vdd2
Monitor3
Monitor2
Monitor1
Monitor0
76 50 BSCK0 /WAIT
A.Vdd1 PC3
77 49 SDA
A.GND1 SDA
C216 78 48 SCL
RFI SCL
1500p/50 79 47 R291 LRCK
AGCO /WAIT
80 46 C283 56
C3T TX/EMPH
C219 81 45 NM BCLK
AGCI LRCK
0.1u/10 82 44 R281 C281 C282
O RFO SCKO
C228 R229 83 56 NM NM
43 R282 DATA
EQ2 DOUT
18p/50 470 84 42 56 C284
EQ1 PA7
C217 R216 85 41 NM LOEJ
RF2- LOEJ
39p/50 1k 86 40 CLCONT
RF- CLCONT
87 39 CONT
A.GND2 CONT R264 R245
88 38 1k
IC201 DSCSNS 100k
A.Vdd2 DSCSNS R253
89 PEQ094A 37 8SNS NM
A NC2
90 36
91
B NC1
35 HOME
R254 C
F HOME 100k
92 34 EJSW R240
E EJSW
93 33 /CDSTBY 47k
REFOUT /CDSTBY ICECK
C223 94 32 ICECK
FE- ICECK
68p/50 95 31 R297
E FEO IO.Vdd1
C 96 30 C211 NM
C IO.GND1
C224 0.1u/10 R237
97 29 RESET
TE- RESET
47p/50 98 28 C233 220
E TEO C.GND
C225 99 27 C210 0.01u/16
TE2 C.Vdd
1u/16 100 26 0.1u/10 R232
Vpp
INTQ(INT1)
TEC
DA.GND1
0
DA.Vdd1
DA.GND
DA.Vdd
REG16
D.GND
ICEMD
X.GND
VPP
REGC
REGS
ROUT
D.Vdd
/XTAL
X.Vdd
LOUT
XTAL
/SCK
/RST
/STB
SO
PD
CVDD
LD
A0
C239
SI
NM
VPP
CVDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
R294
0.1u/10
470
SO
SCK
ICEMD
RST
STB
A0
INTQ
SI
X201
CSS1603-A
VDD2
VDD1
3
16.934 MHz
C203
C209
D
(1608)
0.1u/16
DD (1608) VDD
0.1u/16
0.1u/10
C202
NM
SCK
C299
C238
ND GND
CVDD
SCK
VPP
6
RESET
ICECK
CDSTBY
CDSRQ
RESET
SKIP
CN701
SDA
SCL
VD1
VD2
10 GND
CKS6146-A
6 SO
8 SI
I/O
4
2
VD
1 VD 7.5V
CN702 2 VD 7.5V
NM /CDSRQ
3 /CDSRQ
R706
CVDD 3
ICECK 5
VPP 9
SCK 7
VDD 1
/CDSTBY /CDSTBY
4
SCL R702 220
5 SCL
SKIP 100
6 SKIP
SDA
RESET
R701
100
7 SDA
8 RESET
A
9 VDD 3.3V CN701 E
10 GND GND
DATA
11 DATA
BCLK
12 BCLK
LRCK
13 LRCK
1000p/50
C710
C705
C707
C708
NM
14 GND GND
NM
NM
15 PGND GND
VER LOGIC TABLE /WAIT
16 WAIT
D EJ PLAY OFF
H L L
R711
R710
C703
C702
C701
NM
NM
NM
NM
NM
L IIC-BUS
- -
PGND Digital
L H L
WAIT
GND1
GND2
GND3
DATA
LRCK
BCLK
i h g
GND
PGND1
PGND2
C
DEH-X66BT/XNUC
5 6 7 8
49
1 2 3 4
10.4 BT UNIT
2.2k
R28
C34
1u/10
NM
R27
C35
NM
NC
24 1
1k
1k
NC
23 2
MIC_BIAS VSS
R30
R29
22 3
MIC1P BT18ON
C23
220u/4
21 4
MIC1N BT1.8V
C 20 5
3.3V
BOOTS BT1.8V
19 6
R38 RESET
GND 18 7 BT1.8V
NM 0 BT3.3V BT3.3V
17 8
C37 DBG_Tx
IC21
0.1u/16
C36
16 9
DBG_Rx
CCG1192-A
1 6
CCG1192-A
C22
NM
C28
15 10 VOUT VIN
C24
10u C39
C38
NM
C29
1u/10
2 5
CCG1192-A
14 11 VSS1 VSS2
NM
C32
C33
10u
10u
3 4
220
220
13 12 ON/OFF NC
220
GND
SYSTOBT
BTTOSYS
S-1172B18-E6
GND
CN21
R39
R40
R41
GND GND
CKS6346-
BTDATA
BTSCK
BTLRCK
NM R32
D
NM R33
NM R34
BT MODULE
D
DEH-X66BT/XNUC
50
1 2 3 4
5 6 7 8
D BT UNIT
CN23
2.2k
R28
CKS3857-A
1 VCC
NM
2 VCC
R27
3 GND
4 GND
5 BTDATA
6 BTSCK
7 BTRLCK
8 GND A
.3V
9 NRST_CPU CN971 C
10 SYSTOBT
11 BTTOSYS
BT3.3V IC22
S-1206B33-U3 12 GND
13 MIC1P
VOUT
CCG1192-A
CCG1192-A
1u/10
10u
GND
VSS
C28
14
NM
NM
VIN
C38
C26
C21
C25
NM
C29
15 MIC1N
10u
16 GND
GND
GND
D
NM
C31
D21
NM
NM
D22
D27
NM
GND
D
DEH-X66BT/XNUC
5 6 7 8
51
1 2 3 4
10.5 WAVEFORMS
- CD CORE UNIT(S11.6VA) Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A 2. Reference voltage REFO1(1.65 V)
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div

3HOME 5 V/div 5CLCONT 5 V/div
4LOEJ 5 V/div 4LOEJ 5 V/div
6VD1 10 V/div
12 cm CD Loading operation 12 cm CD Loading operation
Ref.: Ref.:
GND GND
B
Mode: Mode:
Normal Normal
7SIN 1 V/div 1 s/div aFIN 200 mV/div 500 ms/div cTE 500 mV/div 200 ms/div
8CIN 500 mV/div bRFOK(MONI_2) 2 V/div dFE 500 mV/div
9TIN 500 mV/div 7SIN 2 V/div
12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation
C
Ref.: Ref.: Ref.:
REFO REFO REFO
Mode: Mode: Mode:

Normal Normal Normal
dFE 500 mV/div 20 ms/div eMDX 2 V/div 50 ms/div eMDX 2 V/div 5 μs/div
aFIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
cTE 500 mV/div
9TIN 500 mV/div
D
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)
Ref.: Ref.: Ref.:

REFO REFO REFO
Mode: Mode: Mode:

Normal Normal Normal
E aFIN 500 mV/div 200 ms/div cTE 500 mV/div 2 ms/div fRFAGC 1 V/div 500 μs/div
dFE 500 mV/div fRFAGC 500 mV/div cTE 500 mV/div
9TIN 500 mV/div
Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3)
Ref.: Ref.: Ref.:

REFO REFO REFO
Mode: Mode: Mode:

F TEST TEST TEST
DEH-X66BT/XNUC
52
1 2 3 4
5 6 7 8
fRFAGC 1 V/div 2 ms/div fRFAGC 1 V/div 200 ms/div gLRCK 2 V/div 10 us/div
cTE 500 mV/div cTE 1 V/div hBCLK 2 V/div
9TIN 500 mV/div 8CIN 500 mV/div iDOUT(DATA) 2 V/div
7SIN 2 V/div
32 Tracks Jump waveform
(Zoom of 100 Track Jump waveform) Search operation(Outter to Inner) Digital Out waveform
Ref.: Ref.: Ref.:

REFO REFO GND
Mode: Mode: Mode:

TEST Normal Normal
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div

5CLCONT 5 V/div 3HOME 5 V/div
4LOEJ 5 V/div 4LOEJ 5 V/div
12 cm CD Eject operation 12 cm CD Eject operation
C
Ref.: Ref.:
GND GND
Mode: Mode:
Normal Normal
fRFAGC 1 V/div 500 μs/div

9TIN 1 V/div
cTE 1 V/div
aFIN 1 V/div
D
Black Dot (800 μm) during play
Ref.:
REFO
Mode:
Normal
DEH-X66BT/XNUC
5 6 7 8
53
1 2 3 4
11. PCB CONNECTION DIAGRAM

11.1 TUNER AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
several destination.
For further information for
respective destinations, be sure 150
to check with the schematic dia-
gram. JA891
2.Viewpoint of PCB diagrams W.REM&MIC
PREOUT 1
Connector Capacitor JA251 C892 JA892

140 2 2 3 C891 R891 1 5
C260
4 1 5 1 4 6 R892
6 5 3 2 VA891
SIDE A C261 3 C894

C319
R251
R256
R258
C893
C258
R253
Q252 C320
C253
R893 VA892 C331 C33
Q251
R259
1 R255 C328 C317
P251
130 1 C255 C301 C305
C257
B
R257
R254
C254
C256
C252
C318
SIDE B C259 R252 C251
P.C.Board Chip Part
C309
R301
C311
R303
D551 R555 C562
C551
C556
120
C563 C557
IC551 C558
5 C555 C564
C553 R553 R552
110
R551
C554
1 R554
C570
C565
1
C552
D552 L551
100
C
> P 251 (A,6,130) Fuse 3.0 A CEK1386

90
80
70
D
60
50 D CN23
40
E
C CN701
30
20
10
B CN1931
Y
F
0 X 10 20 30 40 50 60 70
A
DEH-X66BT/XNUC
54
1 2 3 4
5 6 7 8
A
SIDE A
C326
1 5 15 25
POWER SUPPLY L901 Q751
10
IC301
20
JA901 C752
E
1 D751 R752
C319 2 4 6 8 10 12 14 16 18
FUSE
1
C325 1 3 5 7 9 11 13
C320
C331 C333 C334 C332 15 17
317 Q752 C753
R310
R312
C313
C301 C305 C307 C303 C327
B
R306 C335 C324 C323 D902 D901 C751
C318 C321
C310
1 R307
R305
C901 C314 FM/AM
R943
C961
R304 D301
D302
ANTENNA
C309
R301
C311
Q301 C329
R303
C312
C941
D941
C322
R302
R311
R944
R309
JA401
R942
E C330
R941
C911
Q941 C930
KN2
R951
C202
R953
C204 L951
C234
C233
C205
D951
C229
C969
C203
C228
P402
IC201 1
C201
C421
P401
C206
40
1
C218
C422
R405
C419
C212 R952 C968
5
C226 E
C227
35
L409 L405
C207 C231 Q951
R406
R313 L407 C410 D401
C210 C423
10
C208 C211 Q302 C465 C420 R401

30
C232 C221 C213 L406 C409 C408

L408
L401
C209 C214 C219 L201 E C461 L402
C417
R403
15
C235
25
L404
L202
C215 C225 R308

C223
C216
C407 C406
C224
R404 C418
C236
C424
C463
C415
C412
C405
C414
C416
20
C402 R402
C403
C404
C413
L403
C217 C220 C425 C401 D402 C458
R685
C681
R409 C464
Q531 L681 C426 C411
C
C455
R681 IC681 R408 C454
E
L531 1 C429 R407 C427 L420
C453
C682 15 10 5 1
C428
R535
R536
L419
R631
R638
R531 R684 C683 C619

C622 L410
R639
R640
R636
C532
20
R682
C531
60
C460 C457
5 C432 C452
C430
X603
R632
R754
R637
R534 R683 C456

R628
25
R410
R633
R634
IC401
R626
C620 R625
1 R753 C433
R635
R629
55
R411 C431 C451 C450
IC531
C434
C625
C441 R417 1
30
R642 C618 L411
50
5
R627
R624
R630
C624
R537
R540
C623
C621
X602 X401
C446
C448
1 R623 R414 35 40 45
R641 R622 1 C435
R532
R533
C613
C612
90 85 80 75 70 65 C440
R619
R538
R618
C459 C447 C449

60
C436 L413
R539 C443 L418
C627 R643 D601 C444
95
L415
C442 C445
55
C437
C467
C628
R415
L414
C626 R617 C466
C439
L417
R416
C468
100
R644 L416
50
R645 R614 R615

C438
C608 C671
R647 C611
105 110
C631 IC601 IC671 R412 R413

45
R613
R646
R648
D602
R612
R649 C629 C610 1 X601 1 C462
40
R650 C609
C672 C607
115 120
R668 C630 C673

35
C606
R651 Q873
R669 R610 D671
C633 1 5 10 15 20 25 30 R611 R671 Q872 E
R653
R601
E
R879
R652 R608 E
Q874
D911
C616
D912
R873
C617
D
Q601 C601 R616
C605
C602
C603
L601
C604
1
R621 R871
R607
R605
R661 R602
R973 R609 L602
R606
R663
R872
C971 R659
D871
D872
C615
C614
R603 R620 R664

C871
R604
R662
R876
R670 E
R660
CN971
R875
R874
Q871 C914
15
R974 E
R975
C973 Q875
R976 C918
10
D CN23 C972
L971
R971
C710 C928
C929
C925
R972 C917
5
C915
C913
C709 L701 C926 C916

R705
C702
C922
C920
C974 C924
C703
R704
C701
C927
R912
R913
1
R914 R911
C921 C919
R707
R724
R701
R711 C705 R720 C923

R715 C706
C704 C912
R723 C708
R722 10 5 1
R702
IC911
R719
R708
R709
R710
R718
R717
R716
R721
C569 C707
R706
E
N701 15 10 5 1
CN701 1R703
R877
C872
C852
KN1 C561
IC552
1
R878
C873
R812
R810
R809
C802
R811
R806
R807
R805
C851
L851 C560 R801
C811
C559 R808
R817
R816
R815
R851
R814
C805
15 C808 R804 C814

R803
C803 C809 IC801 1
D802
R802
D801
D811 R813 C813

L801 D803
C807
VA801
D804
D809
D807
D805
D810
D806
D808
VA802
C810 R818
C804
C806
1 5 15
10 20
CN801 C801
F
FRONT
0 70 80 90 100 110 120 130 140 150 160
A
DEH-X66BT/XNUC
5 6 7 8
55
1 2 3 4
A
A TUNER AMP UNIT
TESTIN
PCL
1
E
F
160 150 140 130 120 110 100 90 80
A
DEH-X66BT/XNUC
56
1 2 3 4
5 6 7 8
SIDE B
A
150
140
1
1
130
B
120
110
100
90
80
70
60
50
40
E
30
20
10
Y
F
X 0
80 70 60 50 40 30 20 10
A
DEH-X66BT/XNUC
5 6 7 8
57
CN801
SIDE B
40
4
4
C1911
C1870
C1869
C1868
R1942
R1941 R1825
1
R1871 25
30
C1941
R1943
R1873
R1824
C1915
30
C1914
C1913
R1870 20
35
E
R1869 15
C1862
D1801
E
Q1859
E
C1863 R1944 40
Q1853 C1855
R1872
Q1868 10
C1861
C1860
C1859
C1864 R1868 IC1851 R1855
R1810
C1805
1
45
L1911 R1859
E
Q1867 Q1866 5
R1861
1
50
10
1
5
D1911 1
0 C1854
KEYBOARD UNIT
IC1802 10 X1801 R1866

C1867
1
C1866
R1860
D1912 L1931
20
C1865
55
95 C1804 R1867
1
D1931 R1854
60
C1912 90
R1851
D1932
R1852
C1852
65
1
85
C1858
C1857
C1856
70
C1923
80 R1858
15 5 1 75
R1856
L1921 Q1852
CN1931
C1851
C1853
D1923
1
C1801
C1803
C1802
R1857
R1865 Q1858
R1809
10
R1922
R1921 R1853 Q1857
E
R1923 C1921
E
1
R1932 R1931 R1862 R1864
1
C1922 20 10 Q1851
L1923
L1922
R1863 Y
3
3
X 0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
B
DEH-X66BT/XNUC
SIDE A
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10

X 0
Y
1
1
1
2
2
1
1
1
1
1
S1835 S1837 S1836 S1839 S1838 S1840 S1834 S1823 S1821 S1832 S1824
6 5 4 3 2 1 DISP RIGHT LEFT BACK BAND 10
3
MULTI-CONTROL
2
11.2 KEYBOARD UNIT
JA1921
AUX
1
20
1
KEYBOARD UNIT
5
5
1
1
5
D1883 D1882
S1826
5
1
PHONE
4
1
D1885 D1886
5
5
3
SEGMENT LCD S1830
D1884 2
V1802 LIST SOURCE 30
1
70 65 60 55 50 45 40 35 30 25 20 15 10 5 1
CN1911
S1828 S1842
USB
1
1
EJECT
40
1
1
1
S1822
1
IC1941
B
B
58
C
D
A
F
5 6 7 8
DEH-X66BT/XNUC
5 6 7 8
59
1 2 3 4
11.3 CD CORE UNIT (S11.6VA)
C CD CORE UNIT(S11.6VA) SIDE A

A
PU UNIT(P11)
(SERVICE)
60
B
TH201 R254
C235
CN101 1 LOAD/CRG
R246
R232 MOTOR
15 10 5 1
HOME
S901
50 C201
F
CN702 R253
10
R245
1 5
C238
E
C299 C710
C R706
R297
C205
40
C707 C705
C220
R701 R702
SPDL
MOTOR
30
D CN701
15 10 5 1
A
CN701
C702
20 C307
REFO1 R710
C701 C308 C312
R306
R303
R308
10 5 1
R304
IC301
E
10 15 20 25
C306
R307
R264
R305
R309
0
X 10 20 30 40 50
F
C
DEH-X66BT/XNUC
60
1 2 3 4
5 6 7 8
C CD CORE UNIT(S11.6VA) SIDE B

A
D101
R102
R101
R103
C102
60
C202
R108
B
Q102
Q101
E
E
C104
X201
1 R109
R294
50
C225
C239
C209 C203
C233
R237 25 20 15 10 5 1 C224 C101
100
C210
C229
C236
C110
C111
C
30
C211 C223
95
R110
R240 R111
R282 40
35
90
C284 R281 C204
IC201 C222
C281
40
C218
C301
85
C282 R216 R218
R291 C219
R229 C217
C283
45
80
C216 C228
C221 R217
50
55 60 65 70 75
30
C212 C215
R215
R214
R260 C250
1 D
C708 S905
C213
C214
20
C703
R711
R313
E
R312
DSCSNS
C304
C303
1
C302
C305
R311 10
S903
R310
C314
C313
C315
0
50 40 30 20 10 X
F
C
DEH-X66BT/XNUC
5 6 7 8
61
1 2 3 4
11.4 BT UNIT
D BT UNIT SIDE A
A
CN23
10 R38
A CN971 1 5 15
R39
R27
R28
C34
C35
40
R40
C37
R41
BT MODULE
D22
CN21
20 15
R32
C21
C31
D21
D27 1 5 10
C36 R33
R34
30
R29 R30
C25
C26
B
C23
IC22
20
C28
C29
C38
10
5
IC21
C32
C22
C33
1
C
X
C24
C39
0
Y
50
40
30
20
10
D BT UNIT SIDE B
50
40
30
20
10
0
D
X 10
20
E
30
40
D
DEH-X66BT/XNUC
62
1 2 3 4
5 6 7 8
12. ELECTRICAL PARTS LIST

NOTE:
Parts whose parts numbers are omitted are subject to being not supplied. A
The part numbers shown below indicate chip components.

Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Meaning of the figures and others in the parentheses in the parts list.
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding B
PC board.
IC 301 (A, 91, 111) IC NJM2068V
The expression of the unit in this manual is shown by u instead of . Please do not make a mistake.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
IC 301 (A,78,142) IC PA2032A
A:DEH-X66BT/XNUC IC 401 (A,150,91) IC TDA7706
B:DEH-X6600BT/XNUC IC 531 (A,94,88) IC 337S3959
IC 551 (A,20,111) Regulator IC BD9876EFJ
C:DEH-X6650BT/XNGS
IC 552 (A,106,24) IC BD2232G-G C
D:DEH-X6650BT/XNCS IC 601 (A,111,77) IC R5S726A0D216FP
IC 671 (A,131,75) IC S-80827CNMC-B8M
E:DEH-X6690BT/XNID IC 681 (A,114,94) Flash ROM Unit(A,B) PEB093A8
(A,114,94) Flash ROM Unit(C,D,E) PEB089A8
Unit Number : QWM3617(A) IC 801 (A,105,18) L-MOS And Gate TC7SET08FUS1
Unit Number : QWM3616(B)
IC 911 (A,145,28) Regulator IC BA49183-V12
Unit Number : QWM3619(C) Q 251 (A,14,130) Chip Transistor RN1910
Q 252 (A,24,131) Chip Transistor RN1910
Unit Number : QWM3618(D) Q 301 (A,86,127) Chip Transistor RN4983
Q 531 (A,94,97) Transistor LSAR523UB
Q 601 (A,93,68) Transistor LTC014YEB
Unit Name : Tuner Amp Unit Q 751 (A,142,139) Transistor KTD2092
D
Unit Number : Q 752 (A,141,134) Chip Transistor RN4983

Q 871 (A,144,59) Transistor 2SA1577
Unit Name : Keyboard Unit Q 872 (A,144,67) Transistor LTC143EUB
Unit Number : CWX4269 Q 941 (A,96,121) Transistor LSCR523UB

D 401 (A,158,107) Diode RN731VN
Unit Name : CD Core Unit(S11.6VA) D 402 (A,158,100) Diode RN731VN
D 551 (A,23,124) Diode CMS03
Unit Number : QWM3750 D 552 (A,22,104) Diode RB056L-40
Unit Name : BT Unit
D 601 (A,130,81) Diode(A,B) RB751SM-40
D 602 (A,91,75) Diode(A,B) RB551VM-30 E
D 751 (A,137,135) Diode DZ2J082M0
D 801 (A,105,15) Diode DZ2S068C
A
Unit Number : QWM3617(A)
D 802 (A,93,17) Diode DZ2S068C
D 803 (A,126,15) Diode DZ2S068C

Unit Number : QWM3616(B) D 804 (A,119,14) Diode DZ2S068C
Unit Number : QWM3619(C) D 805 (A,120,13) Diode DZ2S068C
D 806 (A,116,13) Diode DZ2S068C
Unit Number : QWM3618(D) D 807 (A,114,13) Diode DZ2S068C
D 808 (A,117,13) Diode DZ2S068C
Unit Name : Tuner Amp Unit D 809 (A,112,13) Diode DZ2S068C
F
D 901 (A,141,127) Diode 1SR154-400
MISCELLANEOUS D 902 (A,137,127) Diode 1SR154-400
D 911 (A,158,66) Diode CRG03
IC 201 (A,102,107) LSI PM9013A
DEH-X66BT/XNUC
5 6 7 8
63
1 2 3 4
D 912 (A,161,66) Diode CRG03 (A,139,104) (C,E) RS1/16SS331J
D 941 (A,93,125) Diode DZ2J068M0 R 404 (A,142,99) RS1/16SS105J
L 202 (A,94,102) Inductor CTF1793 R 406 (A,154,108) RS1/16SS105J
L 401 (A,155,104) Chip Coil LCTAWR27J2520
A
L 402 (A,159,104) Chip Coil LCTAWR15J2520 R 407 (A,139,96) RS1/16SS330J
R 408 (A,137,97) (A,B,D) RS1/16SS471J
L 403 (A,151,102) Inductor CTF1786 (A,137,97) (C,E) RS1/16SS361J
L 404 (A,146,102) Inductor CTF1786 R 409 (A,144,98) (C,E) RS1/16SS0R0J
L 405 (A,151,108) Inductor(A,B,D) LCYB68NJ1608
L 406 (A,148,105) Inductor(A,B,D) CTF1389 R 411 (A,138,91) (A,B,D) RS1/16SS681J
(A,138,91) (C,E) RS1/16SS391J
L 407 (A,147,107) Chip Coil(C,E) LCTAWR27J2520 R 412 (A,153,78) RS1/4SA8R2J
L 408 (A,141,104) Inductor(A,B,D) LCTC4R7K1608 R 413 (A,158,78) RS1/4SA8R2J
(A,141,104) Inductor(C,E) LCTC1R5K1608 R 414 (A,139,87) RS1/16SS0R0J
L 409 (A,143,109) Chip Coil(C,E) LCTAWR39J2520 R 415 (A,152,80) RS1/16SS0R0J
B L 410 (A,137,94) Chip Coil(A,B,D) LCTAW470J2520 R 531 (A,91,94) RS1/16SS473J

(A,137,94) Inductor(C,E) LCTAW2R2J2520 R 532 (A,91,85) RS1/16SS222J
L 551 (A,30,107) Inductor CTH1524
R 536 (A,96,92) RS1/16SS472J
L 901 (A,112,141) Choke Coil 600 uH CTH1432 R 538 (A,96,84) RS1/16SS101J
X 401 (A,161,88) Crystal Resonator 36.48 MHz CSS1848 R 551 (A,26,111) RS1/16SS682J
X 601 (A,127,76) Crystal Resonator 12 MHz CSS1847 R 552 (A,30,112) RS1/16SS0R0J
X 603 (A,123,92) Resonator 16.93 MHz CSS1794
R 553 (A,27,112) RS1/16SS1803D
C > P251 (A,6,130) Fuse 3.0 A CEK1386 R 554 (A,27,110) RS1/16SS4302D
P 402 (A,156,111) Surge Absorber HSPC16701B02 R 555 (A,39,124) RS1/10SR471J
VA801 (A,108,13) SMD Varistor MLV0402ES012V0010N R 601 (A,101,66) RS1/16SS473J
VA802 (A,101,13) SMD Varistor MLV0402ES012V0010N R 602 (A,107,63) RS1/16SS473J
CN701 (A,114,32) Connector VKN1192
R 603 (A,109,62) RS1/16SS473J
CN801 (A,109,4) Connector CKS6452 R 609 (A,122,64) RS1/16SS473J
CN971 (A,93,49) Connector VKN1192 R 610 (A,122,70) RS1/16SS473J
JA251 (A,19,138) Pin Jack CKB1099 R 611 (A,123,69) RS1/16SS473J
JA401 (A,158,129) Antenna Jack YKS5041 R 613 (A,122,76) RS1/16SS152J
JA892 (A,42,141) Jack YKS5035
R 614 (A,123,78) RS1/16SS473J
JA901 (A,114,141) Connector CKM1613 R 615 (A,130,79) RS1/16SS473J
D > Fuse 10 A YEK5001 R 616 (A,125,67) RS1/16SS473J
R 617 (A,131,81) RS1/16SS103J
RESISTORS R 618 (A,125,82) (B,D) RS1/16SS473J
(A,125,82) (E) RS1/16SS103J
R 251 (A,18,131) RS1/16SS821J R 619 (A,126,82) (A,C,E) RS1/16SS473J
R 252 (A,13,128) RS1/16SS821J
R 253 (A,15,131) RS1/16SS223J R 622 (A,125,87) RS1/16SS473J
R 254 (A,12,131) RS1/16SS223J R 623 (A,130,85) RAB4CQ473J
R 255 (A,30,132) RS1/16SS821J R 624 (A,120,89) RS1/16SS222J
R 625 (A,114,90) RS1/16SS221J
R 256 (A,19,131) RS1/16SS821J R 626 (A,113,90) RS1/16SS221J
R 257 (A,28,131) RS1/16SS223J
R 258 (A,22,131) RS1/16SS223J R 627 (A,112,88) RS1/16SS221J
E
R 301 (A,68,127) RS1/16SS471J R 628 (A,111,90) RS1/16SS221J
R 302 (A,82,125) RS1/16SS471J R 629 (A,109,92) RS1/16SS221J
R 630 (A,110,89) RS1/16SS221J
R 303 (A,74,127) RS1/16SS471J R 631 (A,108,92) RS1/16SS473J
R 304 (A,78,126) RS1/16SS471J
R 305 (A,90,127) RS1/16SS103J R 632 (A,106,91) RS1/16SS473J
R 306 (A,90,129) RS1/16SS221J R 633 (A,107,90) RS1/16SS101J
R 307 (A,89,128) RS1/16SS223J R 634 (A,103,88) RS1/16SS102J
R 635 (A,102,88) RS1/16SS102J
R 309 (A,89,125) RS1/16SS103J R 636 (A,100,91) RS1/16SS473J
R 310 (A,100,129) RS1/16SS0R0J
R 311 (A,88,125) RS1/16SS473J R 637 (A,101,90) RS1/16SS473J
F R 401 (A,161,106) RS1/16SS221J R 638 (A,104,92) RS1/16SS473J
R 402 (A,161,100) RS1/16SS751J R 639 (A,98,91) RS1/16SS472J
R 640 (A,99,91) RS1/16SS472J
R 403 (A,139,104) (A,B,D) RS1/16SS391J R 643 (A,99,82) RS1/16SS104J
DEH-X66BT/XNUC
64
1 2 3 4
5 6 7 8
R 644 (A,98,79) RS1/16SS101J R 891 (A,58,138) RS1/16SS102J
R 645 (A,96,79) RS1/16SS101J R 892 (A,58,136) RS1/16SS102J
R 646 (A,93,75) RS1/16SS103J R 911 (A,145,40) RS1/10SR1R0J
R 647 (A,98,78) RS1/16SS101J R 912 (A,141,41) RS1/10SR1R0J A
R 648 (A,95,76) RS1/16SS102J R 913 (A,154,41) RS1/16SS223J
R 649 (A,95,75) RS1/16SS102J R 914 (A,131,40) RS1/16SS223J

R 650 (A,95,74) RS1/16SS102J R 941 (A,94,121) RS1/16SS223J
R 651 (A,97,71) RS1/16SS473J R 942 (A,94,122) RS1/16SS473J
R 652 (A,98,69) RS1/16SS222J R 943 (A,95,125) RS1/16SS682J
R 653 (A,100,66) RS1/16SS103J R 944 (A,99,123) RS1/4SA102J
R 659 (A,124,61) RS1/16SS153J R 973 (A,90,63) RS1/16SS222J

R 660 (A,124,60) RS1/16SS153J R 974 (A,98,55) RS1/16SS101J
R 664 (A,133,62) RS1/16SS103J R 975 (A,98,54) RS1/16SS101J
R 668 (A,93,71) RS1/16SS473J R 976 (A,98,52) RS1/16SS101J
R 669 (A,95,69) RS1/16SS473J B
CAPACITORS
R 671 (A,130,69) RS1/16SS104J
R 681 (A,109,97) RS1/16SS473J C 201 (A,96,115) CKSRYB105K10
C 205 (A,94,116) CKSRYB105K10
R 685 (A,120,96) RS1/16SS473J
R 702 (A,114,38) RS1/16SS104J C 207 (A,95,108) CKSSYB104K10
R 703 (A,118,28) RAB4CQ472J C 208 (A,94,106) CKSSYB104K10
R 704 (A,110,40) RS1/16SS104J C 209 (A,93,104) 10 uF CCG1192
C 210 (A,96,106) CCSSCH151J50 C
R 706 (A,108,36) RS1/16SS221J
R 707 (A,109,38) RS1/16SS221J C 211 (A,110,107) CCSSCH151J50
R 708 (A,110,38) RS1/16SS101J C 212 (A,108,109) 10 uF CCG1192
C 215 (A,108,102) CKSSYB104K10
R 711 (A,114,39) RS1/16SS102J
R 715 (A,117,36) RS1/16SS151J C 216 (A,92,101) 10 uF CCG1192
R 717 (A,119,36) RS1/16SS151J C 218 (A,114,109) XCEVW470M16
R 718 (A,123,36) RS1/16SS221J C 219 (A,112,103) 10 uF CCG1192
C 220 (A,106,98) 10 uF CCG1192
R 719 (A,122,36) RS1/16SS104J D
R 752 (A,144,134) RS1/4SA391J C 223 (A,91,101) CKSSYB102K50
R 801 (A,125,22) RS1/10SR222J C 236 (A,110,104) CKSRYB105K10
C 251 (A,35,128) 4.7 uF CCG1201
R 802 (A,104,15) RS1/10SR222J
R 803 (A,121,18) RS1/16SS223J C 252 (A,17,127) 4.7 uF CCG1201
R 804 (A,119,18) RS1/16SS223J C 253 (A,17,130) CCSSCH101J50
R 805 (A,121,19) RS1/10SR101J C 254 (A,11,130) CCSSCH101J50
R 806 (A,118,20) RS1/10SR101J C 255 (A,35,132) 4.7 uF CCG1201
C 256 (A,31,130) 4.7 uF CCG1201
R 807 (A,120,20) RS1/10SR101J
E
R 810 (A,114,21) RS1/10SR220J C 260 (A,33,138) CKSSYB104K10
R 811 (A,117,20) RS1/10SR222J C 261 (A,6,133) CKSSYB103K16
C 301 (A,69,129) CKSRYB224K16
R 812 (A,113,21) RS1/10SR222J
C 314 (A,135,126) CKSRYB104K16
R 817 (A,95,19) RS1/10SR222J
R 851 (A,93,20) RS1/16SS472J C 317 (A,60,129) XCEVW100M16 F
R 872 (A,143,62) RS1/16SS103J C 320 (A,64,134) CCSSCK1R0C50
DEH-X66BT/XNUC
5 6 7 8
65
1 2 3 4
C 322 (A,106,126) CKSRYB104K16 C 467 (A,151,81) (C,E) CKSSYB104K10
C 468 (A,142,79) (C,E) CKSRYB105K10
C 323 (A,106,129) CCSRCH100D50 C 531 (A,91,93) CKSSYB104K10
C 324 (A,102,129) CCSRCH100D50 C 532 (A,94,93) CKSSYB104K10
A
C 325 (A,94,132) CCSRCH100D50
C 326 (A,95,140) CCSRCH100D50 C 551 (A,13,121) XCEVW221M16
C 327 (A,88,129) CKSRYB105K10 C 552 (A,13,107) CKSRYB105K16
C 553 (A,15,110) CKSSYB103K16
C 401 (A,154,100) CKSSYB104K10 C 555 (A,25,112) CKSSYB682K25
C 402 (A,155,101) CKSSYB103K16 C 556 (A,32,120) CEVQW221M6R3
C 403 (A,153,102) CKSRYB105K10
C 405 (A,162,101) CKSSYB103K16 C 557 (A,33,116) CKSRYB105K10
C 561 (A,103,24) CKSRYB105K10
C 408 (A,161,105) CKSSYB103K16 C 564 (A,33,114) 4.7 uF CCG1201
C 409 (A,157,105) CCSSCH6R0D50 C 565 (A,16,107) 4.7 uF CCG1222
B C 410 (A,155,107) CCSSCH330J50
C 603 (A,111,65) CKSSYB104K10
C 415 (A,144,101) 10 uF CCG1192
C 418 (A,142,101) CKSSYB223K16 C 607 (A,127,73) CCSSCH120J50
C 419 (A,147,110) (C,E) CCSSCH150J50 C 608 (A,127,78) CCSSCH120J50
C 420 (A,151,106) (C,E) CKSSYB103K16 C 609 (A,122,73) CKSSYB104K10
C 610 (A,122,75) CKSSYB104K10
C 421 (A,154,111) (A,B,D) CCSSCJ3R0C50
C C 423 (A,144,106) (C,E) CCSSCH8R0D50 C 611 (A,122,77) CKSSYB104K10
C 425 (A,139,99) 10 uF CCG1192 C 613 (A,124,82) CKSSYB104K10
C 428 (A,137,96) (A,B,D) CCSSCH101J50 C 620 (A,114,88) CKSSYB104K10

(A,137,96) (C,E) CCSSCH220J50 C 621 (A,109,88) CKSSYB104K10
C 432 (A,138,92) (A,B,D) CCSSCH820J50 C 624 (A,105,88) CKSSYB104K10
(A,138,92) (C,E) CCSSCK2R0C50
D C 626 (A,100,80) CKSSYB104K10
C 435 (A,139,86) (A,B,D) CKSRYB474K10 C 627 (A,97,81) CCSSCH220J50
(A,139,86) (C,E) CKSRYB105K10 C 628 (A,96,81) CCSSCH220J50
C 439 (A,145,80) (C,E) CKSRYB104K16 C 629 (A,99,75) CKSSYB104K10
C 440 (A,142,86) CKSSYB102K50
C 441 (A,137,89) CCSSCH100D50 C 630 (A,99,73) CKSSYB104K10
C 444 (A,152,82) 2.2 uF CCG1218 C 672 (A,123,73) 1 uF DCH1246
C 681 (A,121,96) CKSSYB104K10
C 445 (A,157,82) (A,B,D) CKSSYB104K10 C 683 (A,120,94) CCSSCJ3R0C50
C 447 (A,157,83) (A,B,D) CKSRYB105K10
C 448 (A,158,85) (A,B,D) CKSSYB104K10 C 701 (A,111,40) CKSSYB103K16
(A,158,85) (C,E) CKSSYB103K16 C 704 (A,120,39) CCSSCH100D50
E
C 449 (A,161,85) CCSSCH9R0D50 C 705 (A,118,39) CCSSCH100D50
C 450 (A,161,90) CCSSCH9R0D50 C 706 (A,117,38) CCSSCH100D50
C 752 (A,140,136) CKSSYB104K10
C 451 (A,159,91) CKSSYB104K10
C 452 (A,159,94) CKSRYB105K10 C 753 (A,147,130) 4.7 uF CCG1201
C 453 (A,160,96) CKSSYB104K10 C 801 (A,124,6) CCSRCH221J50
C 808 (A,108,19) CKSRYB104K16
C 457 (A,162,93) CKSSYB472K25
C 459 (A,154,83) (A,B,D) CCSSCH101J50 C 809 (A,97,16) CCSRCH221J50
(A,154,83) (C,E) CKSSYB102K50 C 810 (A,96,13) CCSRCH221J50
F
C 461 (A,145,104) (A,B,D) CKSSYB104K10 C 811 (A,104,20) CKSSYB104K10
C 464 (A,162,98) 1 uF(C,E) DCH1246 C 873 (A,124,24) CKSRYB104K16
C 891 (A,52,138) CKSRYB104K16
C 465 (A,142,106) (C,E) CKSSYB103K16
C 466 (A,137,79) (C,E) CKSRYB105K10 C 892 (A,34,139) CKSRYB104K16
DEH-X66BT/XNUC
66
1 2 3 4
5 6 7 8
C 893 (A,34,135) CKSRYB102K50 S 1842 (A,15,33) Push Switch CSG1155
C 894 (A,52,134) CKSRYB102K50 CN1911 (A,155,26) Connector CKS6443
C 901 (A,133,124) 2 200 uF/16 V CCH2040 CN1931 (B,109,10) Connector CKS6451
C 912 (A,152,40) CKSSYB102K50 JA1921 (A,156,11) Jack YKN5006 A
C 913 (A,131,43) CKSSYB102K50 V 1802 (A,53,32) Segment LCD CAW2041

C 914 (A,156,56) XCEAT102M16
C 915 (A,132,42) CKSRYB104K16 RESISTORS
C 916 (A,147,43) 4.7 uF CCG1201
C 917 (A,145,46) CKSSYB102K50 R 1809 (B,76,10) RS1/16SS473J
R 1810 (B,63,21) RS1/16SS103J
C 919 (A,151,42) 4.7 uF CCG1201 R 1824 (B,32,31) RS1/16SS273J
C 921 (A,135,42) 4.7 uF CCG1201 R 1851 (B,50,16) RS1/10SR222J
C 923 (A,159,41) 4.7 uF CCG1201 R 1852 (B,48,16) RS1/10SR222J
C 926 (A,140,44) 4.7 uF CCG1201
C 927 (A,140,42) CKSSYB102K50 R 1853 (B,52,9) RS1/10SR222J
R 1854 (B,41,18) RAB4CQ102J B
C 941 (A,96,124) CKSRYB104K16 R 1855 (B,42,22) RAB4CQ102J
C 969 (A,135,113) 10 uF CCG1192 R 1856 (B,26,10) RS1/16SS101J
C 973 (A,98,53) CCSSCH470J50 R 1857 (B,28,8) RS1/16SS101J
B
Unit Number :
R
R
R
1858
1859
1860
(B,13,13)
(B,101,23)
(B,58,21)
RS1/16SS101J
RS1/16SS101J
RS1/16SS101J
Unit Name : Keyboard Unit R 1861 (B,58,24) RS1/16SS101J
R 1862 (B,24,7) RS1/16SS680J
MISCELLANEOUS R 1864 (B,17,8) RS1/16SS680J

R 1866 (B,11,20) RS1/16SS680J
IC 1802 (B,84,22) IC PDC202B R 1868 (B,115,25) RS1/16SS680J C
IC 1851 (B,47,21) IC BH2228FV R 1870 (B,125,27) RS1/16SS680J
IC 1941 (A,155,39) IR RC REC Module PNJ4833M R 1872 (B,131,26) RS1/16SS680J
Q 1851 (B,31,8) Chip Transistor HN1C01FU
Q 1852 (B,32,11) Chip Transistor HN1C01FU R 1931 (B,74,6) RS1/10SR222J
R 1932 (B,78,6) RS1/10SR222J
Q 1853 (B,56,24) Chip Transistor HN1C01FU R 1944 (B,144,27) RS1/10SR101J
Q 1857 (B,20,9) Transistor LSCR523UB
CAPACITORS
C 1801 (B,78,12) CKSSYB104K10
C 1802 (B,77,12) CKSSYB104K10
C 1803 (B,79,12) CKSSYB104K10
Q 1868 (B,128,27) Transistor LSCR523UB D
C 1804 (B,72,21) CKSRYB105K10
D 1882 (A,9,20) LED SMLVN6RGB2UK(B)
C 1805 (B,72,23) CKSSYB104K10
C 1854 (B,52,23) CKSSYB103K16
C 1855 (B,52,24) CKSRYB105K10
C 1911 (B,164,34) CKSRYB104K16
C 1912 (B,140,16) CKSRYB104K16
L 1921 (B,136,11) Inductor CTF1389
C 1941 (B,144,29) 10 uF CCG1192
L 1922 (B,131,6) Inductor CTF1389
L 1923 (B,140,7) Inductor CTF1389
X
S
1801
1821
(B,69,22) Ceramic Resonator 5.00 MHz
(A,51,5) Push Switch CSG1155
CSS1547
C
Unit Number : CWX4269 E
S 1822 (A,11,41) Push Switch CSG1155
S 1823 (A,67,5) Push Switch CSG1155 Unit Name : CD Core Unit(S11.6VA)
MISCELLANEOUS
S 1828 (A,35,33) Push Switch CSG1155 IC 201 (B,24,38) IC PEQ094A
S 1830 (A,25,19) Encoder(MULTI-CONTROL) CSD1168
IC 301 (A,37,12) IC BD8223EFV
S 1832 (A,35,5) Push Switch CSG1155 Q 101 (B,12,54) Transistor 2SA1577
S 1834 (A,76,5) Push Switch CSG1155 Q 102 (B,16,55) Chip Digital Transistor LTA123JUB
X 201 (B,25,50)Ceramic Resonator 16.934 MHz CSS1603
S 1836 (A,123,5) Push Switch CSG1155 S 901 (A,43,54) Spring Switch(HOME) CSN1080
S 903 (B,22,13) Spring Switch(DSCSNS) CSN1081 F
S 1838 (A,99,5) Push Switch CSG1155 CN101 (A,17,58) Connector CKS4808
S 1839 (A,107,5) Push Switch CSG1155 CN701 (A,26,30) Connector CKS6146
DEH-X66BT/XNUC
5 6 7 8
67
1 2 3 4
RESISTORS
C 224 (B,14,45) CCSSCH470J50
R 101 (B,7,59) RS1/10SR2R4J C 225 (B,14,47) CKSSYB103K16
R 102 (B,8,59) RS1/10SR2R4J C 228 (B,10,34) CCSSCH180J50
A
R 103 (B,10,59) RS1/10SR2R7J C 229 (B,9,41) CKSSYB104K10
R 108 (B,14,58) RS1/16SS105J C 233 (B,33,46) CKSSYB103K16
R 109 (B,15,50) RS1/16SS152J
C 236 (B,8,41) CKSSYB104K10
R 214 (B,18,28) RS1/16SS103J C 238 (A,26,45) CKSRYB104K16
R 215 (B,17,28) RS1/16SS393J C 299 (A,26,43) CKSSYB104K10
R 218 (B,10,36) RS1/16SS472J
C 304 (B,28,12) CKSSYB223K16
R 232 (A,31,55) RS1/16SS0R0J C 306 (A,32,7) CKSSYB104K10
B R 237 (B,34,45) RS1/16SS221J C 307 (A,42,19) CKSRYB105K10
R 240 (B,35,40) RS1/16SS473J C 308 (A,32,16) CKSRYB105K10
R 245 (A,34,46) RS1/16SS104J
C 710 (A,34,43) CKSSYB102K50
R 254 (A,37,56) RS1/16SS104J
R 260 (B,30,27) RS1/16SS103J
R
R
R
264
281
282
(A,22,9)
(B,34,38)
(B,34,39)
RS1/16SS102J
RS1/16SS560J
RS1/16SS560J
D
Unit Number : QWM3750
Unit Name : BT Unit
R 291 (B,34,35) RS1/16SS560J
R 294 (B,28,49) RS1/16SS471J
R 303 (A,28,12) RS1/16SS123J
MISCELLANEOUS
C R 304 (A,29,11) RS1/16SS123J
R 305 (A,27,9) RS1/16SS102J IC 21 (A,8,48) Regulator IC S-1172B18-E6
IC 22 (A,21,46) IC S-1206B33-U3
R 306 (A,27,12) RS1/16SS472J CN21 (A,34,27) Connector CKS6346
R 307 (A,26,9) RS1/16SS102J CN23 (A,42,44) Connector CKS3857
R 308 (A,26,12) RS1/16SS472J
R 309 (A,35,7) RS1/16SS473J
R 310 (B,31,9) RS1/16SS472J RESISTORS
R 311 (B,31,10) RS1/16SS472J R 28 (A,42,31) RS1/10SR222J

R 312 (B,31,11) RS1/16SS472J R 29 (A,30,41) RS1/10SR102J
R 313 (B,31,12) RS1/16SS472J R 30 (A,30,37) RS1/10SR102J
R 701 (A,22,38) RS1/16SS101J R 38 (A,42,17) RS1/10SR0R0J
D R 702 (A,24,38) RS1/16SS101J R 39 (A,41,23) RS1/10SR221J
R 706 (A,33,42) RS1/16SS221J R 40 (A,40,23) RS1/10SR221J

R 41 (A,38,23) RS1/10SR221J
CAPACITORS
CAPACITORS
C 104 (B,15,52) CKSQYB475K6R3
C 110 (B,11,44) CKSSYB104K10 C 23 (A,24,40) XCEVW221M4
C 111 (B,12,44) CKSSYB103K16 C 24 (A,7,44) CKSRYB105K10
C 203 (B,22,47) CKSSYB104K10 C 26 (A,27,48) 10 uF CCG1192
C 33 (A,9,54) 10 uF CCG1192
E C 209 (B,29,48) CKSRYB104K16
C 214 (B,17,26) CKSSYB473K16

C 215 (B,19,29) CKSSYB104K10
C 216 (B,13,33) CKSSYB152K50
C 217 (B,10,35) CCSSCH390J50
C 218 (B,10,37) CCSSCH5R0C50
C 219 (B,14,35) CKSSYB104K10

F C 220 (A,18,39) CKSSYB104K10
C 221 (B,14,32) CKSSYB104K10
C 222 (B,14,37) CKSSYB104K10
C 223 (B,13,42) CCSSCH680J50
DEH-X66BT/XNUC
68
1 2 3 4

Deh-X66 6650 6680

Uploaded by

Copyright:

Available Formats

Deh-X66 6650 6680

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Deh-X66 6650 6680

Uploaded by

Copyright:

Available Formats

ORDER NO.

PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

B Where in a manufacturer’s service documentation, for example in circuit diagrams or lists

- Safety Precautions for those who Service this Unit.

Laser diode characteristics

Additional Laser Caution

BLOCK DIAGRAM SCHEMATIC DIAGRAM

1.2 NOTES ON SOLDERING

The following lead-free solders are available as service parts:

Securing the front panel

2.2 DISC/CONTENT FORMAT

3. BASIC ITEMS FOR SERVICE

No. Procedures Item to be confirmed

Item to be checked regarding audio

3.2 PCB LOCATIONS

D BT Unit A Tuner Amp Unit

3.3 JIGS LIST

Before shipping out the product, be sure to clean the

BTSCK BTSCK BTBCK 4

FOM FOM ACTUATOR/

C :DEH-X6650BT/XNGS Q252 Q251

SSENS 35 SOURCE SOURCE 4 2

1 Q1859 Q1858 Q1857 Q1868 Q1867 Q1866

In case of the above signal, the communication

Completes power-on operation.

5.2 ERROR CODE LIST

(1) DISPLAY METHOD

The same code is displayed in the MIN and SEC areas.

(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)

• How to restore from each error is shown below. F

STOP CHECK DEVICE

Pandora CONN. FAILED PRESS BAND KEY TO RETRAY

ERROR-19 Bluetooth connection failed.

NO BT DEVICE GO TO BT MENU TO REGISTER

CONN. FAILED PRESS BAND KEY TO RETRAY

DISCONNECTED PRESS BAND KEY TO RETRAY

5.3 CONNECTOR FUNCTION DESCRIPTION

ANTENNA INPUT MICROPHONE WIRED FRONT

6.2 DISPLAY TEST MODE 2

The information such as the system microcomputer version is checked. A

[How to enter Test mode]

On (an initial value) All off

$ PD number For PEA010A, "010A" is displayed

Switching to next display

Display is normally updated

6.3 SOFTWARE VERSION UP METHOD

How to enter in USB rewriting mode

USB rewriting operation flow

USB Characters displayed on the screen

Red frame: illumination lights up

Press LIST button

(4) Retry count over Retry rewriting

(1) Rewriting succeeded

CAN'T UPDT COMPLETE ERR->RETRY FILE ERROR ERR->RETRY

6.4 CD TEST MODE

To enter the test mode: [4] + [6] -> BUP + ACC ON

[CD] or [SOURCE] [Key]

[BAND] [3] [6] [1] [>] [<] [2]

[BAND] [1] [3] [>] [<] [2]