HCD-101

SERVICE MANUAL AEP Model

UK Model
E Model
Tourist Model

• HCD-101 is the CD PLAYER,

TUNER and AMPLIFIER
sections in CMT-101.

Model Name Using Similar Mechanism NEW

CD Mechanism Type CDM50
Optical Pick-Up Type KSS-313A

SPECIFICATIONS

Tuner section Laser output power Less than 44.6µW*

Tuning range * This output is the value measured at a distance of 200mm from
2 band model the objective lens surface on the optical pick-up block with 7mm
European model: FM : 87.5-108MHz aperture.
(50kHz step) Frequency response 5Hz–20kHz
AM : 522–1,611kHz Signal to noise ratio More than 90dB
Other models: FM : 87.5–108MHz Harmonic distortion Less than 0.05%
(50kHz step)
AM : 531–1,602kHz Amplifier section
(at 9kHz interval) European model:
530–1,710kHz DIN power output 15+15 W (4Ω at 1kHz, DIN
(at 10kHz interval) Continuous RMS power output
3 band model FM : 87.5–108MHz 21+21 W (4Ω at 1kHz, 10%
(50kHz step) THD)
MW : 522–1,611kHz Music power output 26+26 W
(at 9kHz interval) Other model
LW : 144–288kHz Rated RMS power output 16+16 W (4Ω at 1kHz, 1% THD,
(at 3kHz interval) AC240V/AC120V)
Intermediate frequency FM : 10.7MHz Reference RMS power output
AM : 450kHz 22+22 W (4Ω at 1kHz, 10% THD,
Aerial terminals FM : 75Ω unbalanced AC240V/AC120V)
AM : External aerial Inputs VIDEO/PC IN jack : Stereo
terminal phone jack, sensitivity 500mV,
Timer Quartz lock system impedance 47kΩ
Timer setting One-minute step
Sleep timer 10–minute step, max.
90minutes
— Continued on next page —
CD player section
System Compact disc digital
audio system

COMPACT COMPONENT SYSTEM

Laser Semiconductor laser
(λ=780nm)

MICROFILM

Downloaded from www.Manualslib.com manuals search engine

 TABLE OF CONTENTS

Outputs VIDEO/PC OUT jack : Stereo phone 1. GENERAL ······································································ 3

jack, 250mV, 1kΩ
DIGITAL OUT (CD OPTICAL OUT):
Square optical connector jack, –18dBm,
2. DISASSEMBLY
wave jength 660nm 2-1. Case ···················································································· 4
PHONES (headphones) jack : 2-2. Front Panel Section ···························································· 4
Stereo mini jack, accepts head phones of 2-3. PRE Board ·········································································· 5
8Ω or more. 2-4. Function board, Relay board, SP TM board, Trans board,
Power board ········································································ 5
General 2-5. Mechanism Deck ································································ 6
Power requirements 2-6. Chassis (T2) Assy ······························································· 6
European model 220–230V AC, 50/60Hz 2-7. BD Board ············································································ 7
Other models 110–120V or 220–240V
2-8. Roller Arm Block Assy ······················································· 7
AC, 50/60Hz adjustable
with voltage selector 2-9. Chassis (OPT), Chucking Arm Assy ·································· 8
Power consumption 66W (when connected to TC-TX101, 2-10. Motor (SL) Assy (M102), Optical Pick-Up ························ 8
MDS-MX101)
Dimensions Approx. 142×125×260mm (w/h/d) incl. 3. TEST MODE ·································································· 9
projecting parts and controls
Mass Approx. 4.1kg 4. ELECTRICAL ADJUSTMENT ······························ 11

5. DIAGRAMS
5-1. Circuit Boards Location ··················································· 14
5-2. Block Diagram ································································· 15
5-3. Schematic Diagram –BD Section– ··································· 18
5-4. Printed Wiring Board –BD Section– ································ 21
5-5. Printed Wiring Board –Panel Section– ····························· 23
5-6. Schematic Diagram –Panel Section – ······························ 25
5-7. Printed Wiring Board –PRE Section– ······························ 27
5-8. Schematic Diagram –PRE Section– ································· 29
5-9. Printed Wiring Board –Function Section– ······················· 31
5-10. Schematic Diagram –Function Section– ·························· 33
5-11. Printed Wiring Board –Power Section– ··························· 36
5-12. Schematic Diagram –Power Section– ······························ 39
SERVICE NOTE 5-13. IC Pin Function ································································ 42
5-14. IC Block Diagrams ··························································· 44
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT 6. EXPLODED VIEWS
6-1. Front Panel Section ·························································· 47
The laser diode in the optical pick-up block may suffer electrostatic 6-2. Chassis Section ································································· 48
break-down because of the potential difference generated by the 6-3. Mechanism Deck Section-1 (CDM50) ····························· 49
charged electrostatic load, etc. on clothing and the human body. 6-4. Mechanism Deck Section-2 (CDM50) ····························· 50
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the 7. ELECTRICAL PARTS LIST ··································· 51
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.

Flexible Circuit Board Repairing

SAFETY-RELATED COMPONENT WARNING!!
• Keep the temperature of soldering iron around 270 ˚C during
repairing. COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
• Do not touch the soldering iron on the same conductor of the MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
circuit board (within 3 times). LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
• Be careful not to apply force on the conductor when soldering or COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
unsoldering. APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

Downloaded from www.Manualslib.com manuals search engine

—2—
 SECTION 1 This section is extracted
GENERAL from instruction manual.

1 Remote control signal sensor

2 Power switch
3 CD insertion slot
4 Display window
5 6 (CD EJECT) button
6 PHONES terminal
7 BAND button
8 DBFB button
9 =0/)+ (Cue-up musics, or fast rewind / fast
forward) button
0 VOL+/– button
!¡ ^ (CD playback or pause) button
!™ FUNCTION button
!£ p (CD stop) button

Downloaded from www.Manualslib.com manuals search engine

—3—
 SECTION 2
DISASSEMBLY
2-1. CASE

2 Remove the case upward in the

direction of the arrow.

1 Two screws (Case 3 TP2)

1 Two screws (Case 3 TP2)

2-2. FRONT PANEL SECTION

claw

3 Wire (Flat Type)

(27 Core)

4 Connector
(CN916)
2 Pull the front panel out. 1 Two screws
(BV/Ring S Tight)

5 Front panel section

Downloaded from www.Manualslib.com manuals search engine

—4—
 2-3. PRE board

4 Two screws (BVTP 3×8)

!™ PRE board
8 CDM50
!¡ Two Connectors
(CN420, CN422) 7 Connector (CN107)

5 Two screws 9 Wire (Flat type) (21 Core)

(BVTT 3×6) (CN421)

6 Wire (Flat type)

(30 Core)
1 Four screws
(BVTP 3×8)

!º Connector 5 Two screws

(CN423) (BVTT 3×6)
1 Six screws !£ Remove CN911
(BVTP 3×8) 3 Back Panel 6-pin (Posistor board)
2 Connector
(CN814)

2-4. FUNCTION board, RELAY board, SP TM board, TRANS board, POWER board

Power board

6 Relay board

7 SP TM board
!º Power cord (CN902)
!¡ Trans board

8 Two screws (BVTT 3×6)

9 Power board
Trans board

3 Connector (CN910)

5 Screws
(BVTP 3×8)

Function board

4 Function board

2 Connector (CN404)

1 Screws (BVTP 3×8)

Downloaded from www.Manualslib.com manuals search engine

—5—
 2-5. MECHANISM DECK (CDM50)

3 Mechanism Deck (CDM50)

2 Bracket (CDM)
1 Two screw (BVTT 2.6×6)

1 Two screw (BVTT 2.6×6)

2-6. CHASSIS (T2) ASSY

2 Bracket

5 Tension coil spring

3 Four screws 1 Two screws

(BVTT 3×6) (BVTT 2.6×6)

4 Sensor Flexible
board

6 Chassis (T2) assy

Downloaded from www.Manualslib.com manuals search engine

—6—
 2-7. BD board

5 BD board 4 Flexible board

(CN101)

3 Flexible board
(CN106)

1 Two screws
(BVTT ×2)
2 Connectir (CN104)

2-8. ROLLER ARM BLOCK ASSY

3 Roller arm block assy

1 Spring (press)

1 Spring (press)

2 BELT (L)

Downloaded from www.Manualslib.com manuals search engine

—7—
 2-9. CHASSIS (OPT) ASSY, CHUCKING ARM ASSY

7 Chucking arm assy

6 Move the Chucking arm assy
to the position shown in the
illustration and move it up. 5 Spring (CH)
6 Move the Chucking arm assy
to the position shown in the
illustration and move it up.

2 Chassis (OPT)
assy

4 Spring (FL2)

A 1 Move the lever in the

direction of arrow (A).

3 Two Spring (FL)

2-10. MOTOR (SL) ASSY (M102), OPTICAL PICK-UP (KSS-313A)

7 Chassis (OPT) assy

A

4 Screws
(+P 1.7×4)

5 Gear (SL Feed)

2 Motor (SL)assy (M102)

6 Optical Pick-Up
(KSS-313A)

1 Two screws (+BVTT 3×6)

3 Move the shift (SL)
assy in the direction
of arrow A remove
it from chassis (OPT)
and optical Pick-up.

Downloaded from www.Manualslib.com manuals search engine

—8—
 SECTION 3
TEST MODE
There are two methods to enter the TEST mode. 5. Watch operation check (Can be operated only while the main
• How to Enter the Test Mode - 1 power is off.)
Remove the AC power cord from wall outlet, and press [EJECT Press [FUNCTION] and [BAND] at the same time. → Watch
6]. While pressing [EJECT 6], connect the AC power cord to starts counting.
wall outlet.
• How to Enter the Test Mode - 2 Various CD tests
(This method toggles between “Entering the TEST Mode” and Pressing the two keys at the same time enables the various
“Exiting the TEST Mode”.) adjustment and test as follows in the TEST mode, and “ATT”
Turn on the main power. While pressing [TUNING +], press segment is flashing.
[DBFB], release hand from [DBFB] then press [FUNCTION].
(Keep pressing [TUNING] all the way.) 1) Pressing [TUNING–] and [CD EJECT 6] at the same time :
Pressing these buttons again in the same order exits the TEST The present normal tracking balance value (“31” to “36”) is
mode. displayed when the above key operation is performed and
* The small ATT segment lights in the center top of display during (TRBAL.) is displayed.
the TEST mode.
* To exit the TEST mode, disconnect the AC power cord from wall The tracking gain is fixed to “3F” (TOG1 to TOG2: all off)
outlet, or use “How to Enter the TEST Mode - 2”.
2) Pressing [TUNING–] and [DBFB] at the same time :
1. Audio volume control setting (Can be adjusted only during TEST (SHUFFLE) is displayed.
mode.) • ADJUSTMENT mode
Press [CD STOP p] and [VOL–] at the same time When the above key operation is performed, the machine
→ VOL MINIMUM appears enters the ADJUSTMENT mode. The “SHUFFLE” flashes
Press [CD STOP p] and [VOL+] at the same time on display tube.
→ VOL MAXIMUM appears During the ADJUSTMENT mode:
* The audio volume data is kept stored even after the main power The CLV gain is not switched to 8 cm. (The CLV gain is
is turned off. fixed to 12 cm always.)
The machine is ready to enter the AF-ADJUSTMENT mode
2. Audio balance setting (Can be adjusted only during TEST as described below.
mode.)
Press [CD STOP p] and [DBFB] at the same time 3) Pressing [TUNING–] and [FUNCTION] at the same time :
→ LEFT 10 appears (SHUFFLE) and (PROGRAM) are displayed.
Press [CD STOP p] and [FUNCTION] at the same time • AF-ADJUSTMENT mode
→ RIGHT 10 appears After the machine enters the ADJUSTMENT mode by the
Press [CD STOP p] and [CD EJECT 6] at the same time key operation as described in step 2), the machine can enter
→ CENTER appears the AF-ADJUSTMENT mode by pressing the above key
* The audio balance data is kept stored even after the main power operation. [TUNING – /FUNCTION]
is turned off. The “SHUFFLE” and “PROGRAM” flash on display.

3. Key test and FL display tube test (Can be adjusted only during During the AF-ADJUSTMENT mode, the tracking and sled
TEST mode.) servos are turned off in addition to the ADJUSTMENT mode.
• Press [VOL-] and [BAND] at the same time→All FL tubes The machine stops the GFS error check which is normally
light. Pressing the following key in this status enables key performed by software.
checks as follows.
• Sled motor check
• Display depending upon the pressed key When disc is removed by pressing EJECT during the AF-
[FUNCTION] → KEY NO. 1 ADJUSTMENT mode, the sled can be moved to inner
[VOL –] → KEY NO. 2 circumference or outer circumference by pressing [TUNING–
[VOL +] → KEY NO. 3 ] or [TUNING+]. At this time, because the microprocessor
[BAND] → KEY NO. 4 is not sensing the sled position, be careful when moving the
[TUNING+] → KEY NO. 5 sled not to damage gears and other mechanism.
[EJECT 6] → KEY NO. 6
[TUNING –] → KEY NO. 7 4) Pressing [TUNING–] and [VOL–] at the same time :
[STOP p] → KEY NO. 8 • No CDM mode
[PLAY ^] → KEY NO. 9 [1] is displayed.
[DBFB] → KEY NO. 10 When the above key operation is performed, the control on
the slot mechanism which takes in and ejects a CD disc is
• [POWER] → Returns to the TEST mode stopped.
At this time “1” on the display flashes.
* Note: After all keys are (KEY No.1 to KEY No.10) tested, During the no CDM mode,
CHECK OK!! appears. The TOC data is deleted by the [CD EJECT 6] key.
(When the TEST mode is cleared and a CD disc is inserted,
The following items have no relation with the TEST mode. machine reads the TOC again.)

4. Initial setting (All clear of all memories)

Disconnect the AC power cord. While pressing [POWER],
connect the AC power cord to wall outlet.

Downloaded from www.Manualslib.com manuals search engine

—9—
 5) Pressing [TUNING–] and [VOL+] at the same time : ** Other troubles
• Aging mode “TW*SW*”
The machine enters the aging mode by inserting a CD disc TW : Numbers of times that the machine could not read
and performing the above button TOC.
operation. The display starts counting the aging operation SW : Numbers of times that the machine could not
with COUNT display, and “REPEAT” flashes. complete the track search within 16 seconds.
To exit the aging mode and to return the TEST mode, press
Aging operation [TUNING – ] and [VOL +] at the same time.
1. Machine takes a disc into the machine.
2. Reads the TOC.
3. Accesses to the last track.
4. Plays back the last 2 seconds.
5. Ejects the disc.
The one complete operation from step 1 to step 5 is one count.
The cycle is repeated. However, steps 2 to 4 are skipped in all
modes other than the CD function.
Steps 1 and 5 are skipped in the no CDM mode.

The aging operation ends when an error occurs.

Aging error display
“Load Error” : Loading operation is not completed in four
seconds.
“Eject Error” : Eject operation is not completed in four
seconds.
“Q TOC Err” : The Q data could not be read during eight
seconds. (During TOC read)
“Q SRCH Err” : The Q data could not be read during eight
seconds. (During track search)
“Q PLAY Err” : The Q data could not be read during eight
seconds. (During PLAY)
“FOK UP Err” : Focus could not be locked in. (During
setup)
“FOK TOC Err” : Focus is un-locked many times. (During
TOC read)
“FOK SRCH Err” : Focus is un-locked many times. (During
track search)
“FOK PLAY Err” : Focus is un-locked several times. (During
play)
“GFS UP Err” : GFS error. (During setup)
“GFS TOC Err” : GFS error. (During TOC read)
“GFS PLAY Err” : GFS error. (During play)

Display selection during aging

The display can be switched by pressing the [TUNING–] and
[FUNCTION] at the same time :

Example of display

Count display " COUNT 723 " (Machine has repeated for 723 times.)

Elapsed time display " 12 : 05 : 35 " (12 hours 5 minutes 35 seconds have elapsed.)

Other errors " TW 2 SW 1 "

Normal display

Downloaded from www.Manualslib.com manuals search engine

— 10 —
 SECTION 4
ELECTRICAL ADJUSTMENTS

CD SECTION 5. Check the oscilloscope waveform (S-curve) is symmetrical

between A and B. And confirm that peak to peak level is within
Note: 2.4 ± 0.7 Vp-p.
1. CD Block is basically constructed to operate without adjustment.
Therefore, check each item in order given. S-curve waveform
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. symmetry
3. Use the oscilloscope with more than 10MΩ impedance.
4. Clean an object lens by an applicator with neutral detergent
when the signal level is low than specified value with the A
following checks. within 2.4 ± 0.7 Vp-p
5. When optical pickup is replaced during repair, perform the focus B
bias adjustment.

Focus Bias Adjustment

6. After check, remove the lead wire connected in step 2.
oscilloscope Note: • Try to measure several times to make sure that the ratio of
(DC range) A:B or B:A is more than 10:7.
BD board • Select a longer sweep time and increase the brightness to
obtain best waveform.
TP (RF) +
TP (VC) –
RF Level Check
oscilloscope

This adjustment is to be done when the optical block is replaced. BD board

TP (RF) +
Adjustment procedure: TP (VC) –
1. Connect oscilloscope to test point TP (VC) and TP (RF) on BD
board.
2. Turned power switch ON. (Stop state) Procedure:
3. Insert disc (YEDS-18) and press the ^ button. 1. Connect oscilloscope to test point TP (VC) and TP (RF) on BD
4. Adjust RV101 so that the oscilloscope waveform is as shown in board.
the figure below (eye pattern). 2. Turned Power switch on.
A good eye pattern means that the diamond shape (≈) in the 3. Insert the disc (YEDS-18) and press the ^ button.
center of the waveform can be clearly distinguished. 4. Confirm that oscilloscope waveform is clear and check RF signal
level is correct.
• RF signal reference waveform (eye pattern) Note: Clear RF signal waveform means that the shape “≈” can be
VOLT/DIV: 200 mV clearly distinguished at the center of the waveform.
TIME/DIV: 500 ns
RF signal waveform

level:
1.3 ± 0.3Vp-p VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
1.3 ± 0.3Vp-p
When observing the eye pattern, set the oscilloscope for AC
range and raise vertical sensitivity.

S-Curve Check
E-F Balance (Traverse) Check
oscilloscope
BD board
oscilloscope
TP (FEO) + (DC range)
TP (VC) –
BD board

TP (TEO) +
TP (VC) –
Procedure:
1. Connect as oscilloscope to test point TP (VC) and TP (FEO) on
BD board. Procedure:
2. Connect a lead wire between test point TP (FOK) and Ground. 1. Set up the TEST mode step 3) AF-ADJUSTMENT. (see page
3. Turned Power switch on. 9.)
4. Insert disc (YEDS-18) and turned Power switch on again to 2. Connect as oscilloscope to test point TP (TEO) on BD board.
actuate the focus search. (actuate the focus search when disc 3. Turned Power switch on.
table is moving in and out.) 4. Insert the disc (YEDS-18) in and press the ^ button.
5. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0V dc, and check the amplitude.

Downloaded from www.Manualslib.com manuals search engine

— 11 —
 Traverse waveform
symmetry

A
0V
B

amplitude: 300 ± 100 mVp-p

specified value: • A-B × 100 = less than ± 7%
2 (A+B)
• A+B = 300 ± 100 mVp-p

Focus/Tracking Gain Adjustment

This gain has a margin, so even if it is slightly off. There is no
problem.
Therefore, do not perform, RV102 and RV103 adjustment.
Please note that it should be fixed to mechanical center position
when you moved and do not know original position.

Adjustment Location:
[BD BOARD] — Component side —

(RF)

(VC)

(A.GND)
IC102

(FOK) (D.GND)
(TEO) RV101
(PCK)
RV103
IC104 (TEI)
(FEO) RV102

(FEI)

(TAO)

Downloaded from www.Manualslib.com manuals search engine

— 12 —
Downloaded from www.Manualslib.com manuals search engine
— 13 —
 SECTION 5
DIAGRAMS
5-1. CIRCUIT BOARDS LOCATION

TRANS board
POWER IC board

PRE board RELAY board

POWER board

BD board

SP TM board

POSISTOR board

RDS board

FUNCTION board
HP board

SENSOR board MOTOR board

EJECT board
SWITCH board

PANEL board

VOL SEL board

Downloaded from www.Manualslib.com manuals search engine

— 14 —
 HCD-101

5-2. BLOCK DIAGRAM R-CH

J660
TB401 IC401
TUNER UNIT INPUT SELECT PHONES
J402
FM 1 FM ST-L 17 12 IC423
5 EFFECT IC424 IC801
ANTENNA IC404(1/2) SWITCH VOL LOUDNESS
CN410 ST-R 19 R-CH 4 BUFFER POWER AMP

4 AM 15 3 15 13 18 L IN L OUT 19 +
AM
14 IC430 12
BUFFER Q424
DET 19 2 DBFB R OUT 2 R-CH TM801
STEREO

MUTE
TUNED
MUTE

1 14 SPEAKER
DO

CE
CL

DI

11
DATA

STB

RY801
CK

22 21 20 9 8 6 7
C
B
A

Q802,803 Q804
11 10 9 A B 11 10 12 STAND-BY RELAY R-CH +
10 9 SWITCH DRIVE
J401
J401(2/3)
IN L Q420,422
Q425
IC402 MUTE Q801 2 L MD
MUTE
VIDEO/ REC OUT SWITCH STAND-BY
PC SWITCH SWITCH J402(2/3) OUT

OUT L 9 8 2 L TAPE
6
Q401
D+5.6V
CNJ401(1/3)
9V
MD L 1 FAN
IC802
1 3 Q820,822 Q823,824
IN CNJ402(1/3) DELAY
CUTOFF FAN
TAPE L 1 SWITCH DRIVE

Q805 Q821
STAND-BY POWER ON
IC422 SWITCH SWITCH ANA -9V
SURROUND
IC410 SWITCH
8BIT S/P CONV
Q421 2 IC403
F.A 5 SURROUND 13 AUB CONTROL J401(3/3)
F.B 6 SWITCH
CONTROL 1 R-CH
F.C 7 8 9 8 AUB
SURR 16 6
F.A 14 9 AC
2 SIN F.B 15 4 3
3 CK 5 11 AC
4 LAT POW 12

J402(3/3)
AUB1 9
AUB2 8 8 AUB

ST POWER 13 AC 9 AC
SIGNAL PATH
CD POWER 10
XRST 11 AC 11 AC : FM
IC602
BUFFER 2
IC601 : MD
4 RDS
AEP,German, 16 : VIDEO/PC
UK MODEL
: TAPE
SW+5V
: REC

2 IC901 : CD
CD
1 OPTICAL : DIGITAL OUT
Q404
OPTICAL PICK-UP BLOCK IC701 DIGITAL OUT
SYSTEM CONTROL 3
(KSS313A) • R-CH : Same as L-CH
9 TA LATCH AU BUS OUT 2
IC103 47 TA MUTE AU BUS IN 39 IC751
IC101
DIGITAL SIGNAL IC104
E K RF AMP, REMOTE
FOCUS/TRACKING, PROCESSOR DIGITAL FILTER 6 TA DATA
B+ SIRCS 41 CONTROL
A SLED SERVO D/A CONVERTER 7 TA CLOCK RECEIVER
50 XRST NON
C 42 RDS DATA BACK-UP 5V
A D 35 PD1 D OUT 39
D 37 RDS CLK
RFO 31 14 RF
Q701
B 8 SP LATCH IC850
B C 36 PD2 PCMD 21 2 DATA L OUT 16 RESET 10 RESET 3 1
SWITCH RESET
C OUT 23 55 CN IN 3 ST D OUT
ST +12V Q910,911
SENS 24 54 SE IN BCLK 22 3 BCLK R OUT 13 R-CH 5 ST CE
SWITCH
(TUNER)
F FOK 25 1 FOK LRCK 20 1 LRCK 4 ST CLK AC CUT 38
F
38 F 45 ST D IN
E FL701
39 E DATA 21 56 DATAO XTO 6 POW B+ Malaysia, Singapore, Hong Kong,
50 TU MUTE FLUORESCENT Tourist MODEL
XLT 20 57 XLTO XTAI 34 4 CKO X101 POW B-
LD Q101,102 43 TUNED INDICATOR TUBE
33 LD CLK 19 59 CLKO XTI 5 16.9344MHz L901
LD DRIVE 44 STEREO Q701 Q931 IC931 S901
T0 100 SW D +5V 3 1
RV101 BUFFER CD SW+5V REG 240V 120V
MLAT 28 21 DF LATCH SW A +5V T901
T1 99 F1 F2 F1
FOCUS
CLOK 27
BIAS T11 89 IC932
DATA 26 CDP +7V 3 1 F2
88 REG
FE BIAS 37 S0 AEP, UK, German MODEL
PD 80 D901
LASER ON 34 PHD DATA 51 18 CD DATA .
DIODE IC102 78 D+5.6V IC933
RV102 CLOK 53 17 CD CLOCK S34 3 1 F901
VR TRACKING/FOCS 53 (IC701) REG
COIL DRIVE FOCUS D703 L701
SLED/SPINDLE GAIN XLAT 52 20 DSP LATCH NON BACK-UP 5V
MOTOR DRIVE S1 (IC701)
FEI 2 SQCK 47 22 SQCLK DISC SET 26 D704
DISC SET BACK-UP
TRK+ XRESET 7 22 XRST AC IN
18 (IC701)
TRACKING TRACKING FEO 1 SCOR 43 36 SCOR
COIL COIL 19 13 TAO S2 IC941
TRK DRIVE RV103 SQSO 46
52 24 SUBQ DISC DET 27 D +5V 3 1
17 12 TAM DISC DET REG
2-AXIS TRACKING SENS 49 19 SENS D902 AC
DEVICE GAIN Q921
FCS+ ANA +9V
12 12 X1 SWITCH
FOCUS 15 6 FEO TEO 42 KEY0 32 AC
FOCUS X701 D903
COIL COIL 9 14
FCS DRIVE 16 7 FEM 5MHz
11 11 X2
TEI 44 D904
16 S101 15 XT1
M102 26 LIMIT SW X702 S761 S755 S751 S752 S753 S754
SLED 63 SPOD
SLED IC105 32.76kHz D905
M MOTOR 25 16 SLO LOADING MOTOR POWER EJECT DBFB VOL VOL + FUNCTION Q924
MOTOR DRIVE 14 XT2 ANA -9V
27 15 SLM DRIVE SWITCH
KEY1 33
M103 9 LM2 2 48 LOAD OUT
M101 1
SPINDLE LOADING M
SPINDLE M MOTOR 4 3 MDP MOTOR
MOTOR DRIVE 7 LM1 4 49 LOAD IN
2 S762 S763 S764 S765 S766
PLAY/ STOP REW/AMS FF/AMS BAND
D751 49 LOAD IN
PAUSE

49 LOAD IN
PLAY/PAUSE

— 15 — — 16 — — 17 —

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
HCD-101

5-13. IC PIN FUNCTION 5-14. IC BLOCK DIAGRAMS

• IC701 µPD780206GF-023-3BA

Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 D+5V — Power supply (+5V) 51 PLAY LED O CD PLAY LED output IC 102 BA6397FP
2 AUB OUT O AU_BUS output 52 PAUSE LED O CD PAUSE LED output

27 OUT4A

26 OUT4B

18 OUT3B

17 OUT3A
3 ST DATA OUT O Tuner pack (TB401) serial data output 53 S34 O

25 IN4A

24 IN4B

20 IN3B

19 IN3A


28 GND

16 OP+

15 OP–
22 VCC

21 VCC
23 VC
4 ST CLOCK O Tuner pack (TB401) clock output 54 S33 O 

5 ST LATCH O Tuner pack (TB401) latch output 55 S32 O  VCC VCC

6 TA DATA OUT O Data output to electronic VOL (IC424) serial-to-parallel conversion IC (IC410) 56 S31 O

 DRIVE
DRIVE
BUFFER
DRIVE
7 TA CLOCK O Clock output to electronic VOL (IC424) serial-to-parallel conversion IC (IC410) 57 S30 O  BUFFER BUFFER
 DRIVE
BUFFER
8 LATCH (S.P) O Latch output to serial-to-parallel conversion IC (IC410) 58 S29 O 


LEVEL

LEVEL
SHIFT

SHIFT
9 LATCH (VOL) O Latch output to electronic VOL (IC424) 59 S28 O 
10 RESET I SYSTEM RESET 60 S27 O 

11 X2 O Main clock oscillator output (5MHz) 61 S26 O 

12 X1 I Main clock oscillator input (5MHz) 62 S25 O 

SHUT DOWN


THERMAL
13 D.GND — Connected to Vss 63 S24 O  REGULATOR
14 XT2 O Watch oscillator output (32.768 kHz) 64 S23 O  DRIVER MUTE

15 XT1 I Watch oscillator input (32.768 kHz) 65 S22 O 
 FL tube segment output
16 D+5V — Positive power supply (+5V) 66 S21 O 
17 CD CLOCK O CD clock output 67 S20 O 



LEVEL

LEVEL
SHIFT

SHIFT
18 CD DATA O CD data output 68 S19 O

19 SENSE I CD DSP sense input 69 S18 O 
20 DSP LATCH O CD DSP latch output 70 S17 O 

21 DF LATCH O CD D/A latch output 71 S16 O  DRIVE DRIVE DRIVE
 DRIVE
BUFFER BUFFER BUFFER
22 SQCLK O CD Sub Q clock output 72 S15 O  BUFFER

23 (OPEN) — (Not used) 73 S14 O 

IN2B 10

OUT2A 11

OUT2B 12

GND 13

OP-OUT 14
1

9


OUT1A

OUT1B

IN1A

IN1B

TR-B

REG 0

XRST

GND

IN2A
24 SUBQ I Sub Q data input 74 S13 O

25 AD.GND — Ground 75 S12 O 

26 DISC SET I CDM chucking sensor 76 S11 O 
27 DISC DET I CDM disc sensor 77 S10 O

 IC103 CXD2507AQ
28 LOAD END I CDM disc sensor 78 S9 O  IC105 LB1638M

SPOD
SPOC
SPOB
SPOA
XLON

CLOK
CLKO
29 DISC IN I CDM disc sensor 79 VG–27V — FIP controller pull-down resistor is connected here (–27V)

DATO
XLTO

CNIN

XLAT
SEIN
VDD
GND 1 10 N.C.
30 DISC 8/12 I CDM disc sensor 80 S8 O 
31 DEST I Identification input of destination 81 S7 O  64 63 62 61 60 59 58 57 56 55 54 53 52


32 KEY0 I Key input 82 S6 O 


CONTROL LOGIC
IN1 2 9 OUT1
33 KEY 1 I Key input 83 S5 O  FOK 1
SERVO AUTO
SEQUENCER 5
51 DATA
 FL tube segment output MON 2 50 XRST 8 VS
34 AD+5V — Built-in A/D converter analog power supply (+5V) 84 S4 O  MDP 3 49 SENS
35 AD+5V REF — Built-in A/D converter reference voltage input (+5V) 85 S3 O  CPU SUB CODE VCC 3
 MDS 4 14 INTERFACE PROCESSOR 48 MUTE 7 OUT2
DIGITAL
36 SCOR I DSP SCOR input 86 S2 O  LOCK 5
CLV
47 SQCK IN2 4
 TEST 6
4 46 SQSO
37 RDS.CLOCK I DSP clock input 87 S1 O  FILO 7 45 EXCK GND 5 6 N.C.
38 AC.CUT I AC power off detection 88 S0 O  8
DIGITAL EFM
44 SBSO
FILI PLL DEMODULATOR
43 SCOR
39 AUB IN I AU_BUS input 89 T11 O  PCO 9

40 D.GND — Ground 90 T10 O

 VSS 10 42 VSS
 AVSS 11 ASYMMETRY 3 41 WFCK
41 SIRCS I SIRCS remote control input 91 T9 O  CLTV 12
CORRECTOR 40 EMPH
 5
D/A DIGITAL 39 DOUT
42 RDS.DATA — (Not used) 92 T8 O  AVDD 13 INTERFACE OUT
 RF 14 38 C4M
GENERATOR

6
43 TUNED I Tuner pack (TB401) TUNED input 93 T7 O  BIAS 15 37 FSTT
CLOCK

44 STEREO I Tuner pack (TB401) STEREO input 94 T6 O  FL tube grid output ASYI 16
16K ERROR 36 XTSL
 ASYO 17
RAM CORRECTOR
35 XTAO
45 ST DATA I Tuner pack (TB401) DATA input 95 T5 O  3
 ASYE 18 34 XTAI
46 D+5V — Positive power supply (+5V) 96 T4 O  WDCK 19 33 MNTO

47 TA.MUTE O TA mute output 97 T3 O



48 LOAD OUT O CDM 50 load output 98 T2 O 
 20 21 22 23 24 25 26 27 28 29 30 31 32
49 LOAD IN O CDM 50 load input 99 T1 O 
LRCK
PCMD
BCLK
GTOP
XUGF
XPCK
VDD
GFS
RFCK
CZPO
XROF
MNT3
MNT1


50 ST.MUTE O Tuner pack (TB401) mute output 100 T0 O

— 42 — — 43 — — 44 —

Downloaded from www.Manualslib.com manuals search engine

 IC104 PCM1710U-B IC410 BU2092

LRCIN 1 28 ML/DSD VSS 1 18 VDD

CONTROL CIRCUIT

DIN 2 INPUT DATA 2 17 OE

27 MC/DM2
INTERFACE DIGITAL MODE 12-BIT SHIFT REGISTER
FILTER CONTROL
CLOCK 3 16 Q11
BCKIN 3 26 MD/DM1
12-BIT STORAGE
LCK 4 REGISTER 15 Q10
CLKO 4 TIMING 25 MUTE
CONTROL Q0 5 OUTPUT BUFFER 14 Q9
(OPEN DRAIN)
XTI 5 24 MODE Q1 6 13 Q8

XTO 6 23 CKSL Q2 7 12 Q7
NOISE
SHAPER Q3 8 11 Q6
DGND 7 22 DGND
Q4 9 10 Q5
VDD 8 21 VDD
5-LEVEL DAC 5-LEVEL DAC
RIGHT LEFT
VCC2R 9 20 VCC2L

GND2R 10 LOW-PASS FILTER LOW-PASS FILTER 19 GND2L

RIGHT LEFT

EXT1R 11 18 EXT1L

3-STAGE AMP 3-STAGE AMP

EXT2R 12 LEFT 17 EXT2L
RIGHT

VOUTR 13 16 VOUTL

GND1 14 15 VCC1

IC941 M5293L

GND 2

5k
REFERENCE
5
VOLTAGE
27k
+ 3 OUT
REFERENCE –
ON/OFF 4
VOLTAGE

OVERHEAT OVERCURRENT
PROTECTION LIMITTER
IN 1

IC424 TC9211P
VSS VDD
1 20
OUT 2 19 OUT

IN 3 18 IN
L-CH R-CH
DATA DATA
L-ch LD1 4 LATCH LATCH
17 LD1 R-ch

LD2 5 16 LD2

A-GND 6 15 A-GND

NC 7 14 NC

CS1 8 13 CS2
SHIFT REGISTER (13-BIT)
GND 9 LEVEL LEVEL 12 STB
SHIFT SHIFT
STROBE GENERATOR
CK 10 11 DATA

Downloaded from www.Manualslib.com manuals search engine

— 45 —
 IC101 CXA1782BQ

RF M
PHD2

PHD1

RF O

RF I
PHD

CC1

CC2

FOK
LD

CP

CB
36 35 34 33 32 31 30 29 28 27 26 25

–
–
+

–
+

+
+

–
+
–

–
APC LEVELS

–
+ +

–
+ 24 SENS
–
IIL
–
FOK

–
MIRR
+

RF IV AMP1 DFCT
TTL 23 C. OUT

– 22 XRST
+

TTL
RF IV AMP2 21 DATA
FE BIAS 37 TTL • IIL DATA RESISTOR • INPUT SHIFT RESISTOR
• ADDRESS DECODER 20 XLT
+ IIL
–
FE AMP

IIL • OUTPUT DECODER 19 CLK

F 38 –
+

–
F IV AMP TOG1-3 FS1-4 TG1-2 TM1-7 PS1-4
+

BAL1-3
18 VCC
E 39 – FZC COMP
+

+
–

E IV AMP + +
–

EI 40

TE AMP
–
BAL1

BAL2

BAL3

• TRACKING
• ISET 17 ISET
HPF COMP LPF COMP • PHASE
COMPENSATION
VEE 41
– TM6
TEO 42 TG1
–
+

+ 16 SL 0

TM5
TOG1

TOG2

TOG3

+
TM4 15 SL M
–
TZC COMP • FCS PHASE
LPFI 43 COMPENSATION
TM3 TM2 14 SL P
TEI 44
DFCT
ATSC 45 • WINDOW COMP FS1
TM1
+

TM7
ATSC 13 TA O
TZC 46 FS2 –

TDFCT 47
DFCT
TG2
+

• F SET

–
–
VC 48 FS4
+

1 2 3 4 5 6 7 8 9 10 11 12
FEO

FEI

FDFCT

FGD

FLB

FE O

FE M

SRCH

TGU

TG2

FSET

TA M

Downloaded from www.Manualslib.com manuals search engine

— 46 —
 SECTION 6
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number • Abbreviation
have some differences from the original one. in the exploded views are not supplied. SP : Singapore
• Items marked “*” are not stocked since they • Hardware (# mark) list is given in the last of MY : Malaysia
are seldom required for routine service. Some this parts list. HK : Hong Kong
delay should be anticipated when ordering these G : German
items. JE : Tourist

6-1. FRONT PANEL SECTION

10

10
11
4 13

11
11

15

14 6
11
3

11
7
12
2 8
1

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 4-994-808-01 PANEL (ALUMINUM), FRONT (SP,MY,HK,JE) * 7 1-667-385-11 SWITCH BOARD
1 4-994-808-11 PANEL (ALUMINUM), FRONT (AEP,G,UK) 8 4-930-336-61 FOOT (FELT)
2 4-942-636-21 EMBLEM (No.3.5), SONY 9 4-958-107-01 SCREW (BV/RING S TIGHT)
3 4-994-813-01 FILTER (RM) 10 3-363-099-51 SCREW (CASE 3 TP2)
* 4 1-667-387-11 HP BOARD 11 4-951-620-01 SCREW (2.6X8), +BVTP

* 5 4-994-819-31 CASE 12 X-4948-993-1 PANEL (M) ASSY

* 6 A-4403-540-A PANEL BOARD, COMPLETE (SP,MY,HK,JE) 13 1-782-805-11 WIRE (FLAT TYPE) (5 CORE)
* 6 A-4403-560-A PANEL BOARD, COMPLETE (AEP,G) 14 1-782-781-11 WIRE (FLAT TYPE) (27 CORE)
* 6 A-4403-727-A PANEL BOARD, COMPLETE (UK) * 15 1-667-388-11 EJECT BOARD

Downloaded from www.Manualslib.com manuals search engine

— 47 —
 6-2. CHASSIS SECTION

#5 #1
#4
56
54 not supplied
55

not supplied
#1

#3
#1 #1
53 57
63 #1
#1
62

67 #1
68
61
52
#5 58 #2
not supplied #1
64
T901
#3 59
#3 #3
#5 SP, MY
MODEL HK
71 MODEL
72
65 73
#5
70
60 EXCEPT UK
MODEL 65
#5 69 66
not supplied #5 #1
73

#5 51 UK
MODEL
65

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 1-668-138-11 POSISTOR BOARD * 63 1-667-386-11 SP TM BOARD
* 52 1-667-384-11 TRANS BOARD 64 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING
* 53 4-995-817-01 COVER (CABLE) ! 65 1-776-060-11 CORD, POWER (EXCEPT UK)
54 1-782-780-11 WIRE (FLAT TYPE) (21 CORE) ! 65 1-776-061-21 CORD, POWER (UK)
* 55 1-667-823-11 POWER IC BOARD 66 3-703-244-00 BUSHING (2104), CORD

* 56 A-4403-527-A PRE BOARD, COMPLETE * 67 4-994-825-01 COVER (TR)

* 57 4-994-816-01 PANEL, BACK 68 4-812-134-11 RIVET (DIA. 3.5), NYLON
58 1-698-997-11 FAN, DC 69 4-889-836-01 CUSHION
* 59 A-4403-536-A FUNCTION BOARD, COMPLETE (SP,MY,HK,JE) * 70 1-667-382-11 VOLSEL BOARD
* 59 A-4403-553-A FUNCTION BOARD, COMPLETE (AEP,G) * 71 A-4403-559-A RDS BOARD, COMPLETE (AEP,G,UK)

* 59 A-4403-726-A FUNCTION BOARD, COMPLETE (UK) ! 72 1-569-008-11 ADAPTOR, CONVERSION 2P (SP,MY)

60 4-965-822-01 FOOT ! 73 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
* 61 A-4403-537-A POWER BOARD, COMPLETE (SP,MY,HK,JE) ! T901 1-431-559-11 TRANSFORMER, POWER (AEP,G,UK)
* 61 A-4403-555-A POWER BOARD, COMPLETE (AEP,G,UK) ! T901 1-431-560-11 TRANSFORMER, POWER (SP,MY,HK,JE)
* 62 1-667-822-11 RELAY BOARD

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
— 48 —
 6-3. MECHANISM DECK SECTION-1
(CDM50)

121
122 135
124

125
not supplied
123
#5
#4
#5 126
136
137
120 #8
S002 M103
127
B
129
D 128
B C
118 117
119 116
D
111 113
108 130
not supplied
114
#5
112 #5
C 131
111
106 110
103 109
131
132
107
103
105 104 102
#10
102 101

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 3-387-776-01 BELT (L) 120 3-906-921-01 SPRING, TENSION
102 3-578-242-11 WASHER 121 3-906-924-01 SPRING, TENSION
103 3-384-894-01 GEAR (R1) * 122 1-653-378-51 SENSOR BOARD
104 3-384-895-01 GEAR (R2) 123 3-907-588-11 SPRING (FL2)
105 3-384-900-01 SPRING (PRESS) 124 X-3366-102-1 SLIDER (R) ASSY

* 106 X-3366-857-1 ARM ASSY, ROLLER 125 3-384-889-01 LEVER (R)

107 3-384-896-01 GEAR (DOWN) 126 3-906-939-11 GEAR (RACK 2)
108 A-3252-591-A GEAR ASSY, ROLLER * 127 X-3366-853-1 CHASSIS (R) ASSY
109 X-3366-858-4 ARM ASSY, FRICTION 128 3-906-940-01 LEVER (ST2)
110 3-384-899-01 SPRING (FRICTION) 129 3-384-916-01 SPRING (FL)

111 3-384-892-01 BEARING (ROLLER) * 130 X-3373-302-2 CHASSIS (M) ASSY

112 3-386-150-01 RING (ROLLER), RETAINING 131 3-384-923-01 SHAFT (DAMPER)
113 3-701-438-11 WASHER, 2.5 * 132 A-4699-821-A BD BOARD, COMPLETE
114 3-909-408-01 ROLLER (T2) 135 3-384-914-01 DAMPER
116 3-384-888-01 SLIDER (L) 136 3-384-914-12 DAMPER

117 3-384-887-01 LEVER (L) 137 1-658-806-11 SENSOR FLEXIBLE BOARD

* 118 X-3371-324-3 CHASSIS (T2) ASSY M103 A-3252-580-A MOTOR (L) ASSY (LOADING)
119 3-906-923-11 GUIDE (DISK 2) S002 1-692-441-11 SWITCH, MICROPHONE (DISC DET)

Downloaded from www.Manualslib.com manuals search engine

— 49 —
 6-4. MECHANISM DECK SECTION-2
(CDM50)
158

160
#4 157

159
156 168

M101

155

#7
#7

154
M102

153
161

164

#5

152 165
#9
167 #6 #5

166 162

163
151

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151 A-3252-586-A SHAFT (SL) ASSY 162 3-384-912-11 GEAR (K2)
! 152 8-848-283-11 OPTICAL PICK-UP KSS-313A 163 3-570-615-02 POLY-WASHER (DIA.1.2)
153 3-384-922-01 GEAR (SL FEED) 164 3-384-913-11 SPRING (THRUST RETAINER)
154 3-384-920-01 RETAINER (SL FEED) * 165 1-653-379-51 MOTOR BOARD
155 X-3370-190-1 CHASSIS (OPT) ASSY (OUTSERT) 166 3-918-103-11 SCREW
* 156 3-384-915-11 BRACKET (CP)
167 1-653-376-11 MOTOR FLEXIBLE BOARD
* 157 3-384-918-01 RETAINER (DISC) 168 3-701-442-01 WASHER, POLYETHYLENE
158 X-3372-948-1 ARM ASSY, CHUCKING M101 X-3367-484-2 MOTOR (SP) ASSY (SPINDLE)
159 3-384-917-01 SPRING (CH) M102 A-3252-585-A MOTOR (SL) ASSY (SLED)
160 3-926-152-01 SCREW (+PM1.7X2.5)
161 X-3366-100-1 BASE (DRIVING) ASSY

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
— 50 —
 SECTION 7
ELECTRICAL PARTS LIST BD
NOTE:
When indicating parts by reference number,
• Due to standardization, replacements in the • RESISTORS
please include the board name. parts list may be different from the parts All resistors are in ohms.
specified in the diagrams or the components METAL: metal-film resistor
The components identified by mark ! or used on the set. METAL OXIDE: Metal Oxide-film resistor
dotted line with mark ! are critical for safety. • -XX, -X mean standardized parts, so they may F: nonflammable
Replace only with part number specified. have some difference from the original one. • COILS
• Items marked “*” are not stocked since they uH: µH
• Abbreviation are seldom required for routine service. Some • SEMICONDUCTORS
SP : Singapore delay should be anticipated when ordering these In each case, u: µ, for example:
MY : Malaysia items. uA...: µA... , uPA... , µPA... ,
HK : Hong Kong • CAPACITORS: uPB... , µPB... , uPC... , µPC... ,
G : German uF: µF uPD..., µPD...
JE : Tourist

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* A-4699-821-A BD BOARD, COMPLETE C145 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
******************* C146 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C147 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
3-934-077-01 CUSHION (LIGHT INTERCEPTION) C148 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C149 1-164-346-11 CERAMIC CHIP 1uF 16V
< CAPACITOR >
C153 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C101 1-126-607-11 ELECT CHIP 47uF 20% 4V C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C102 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V C171 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V C172 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C105 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C173 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C106 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V
C174 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C107 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V C175 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V C178 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C109 1-164-232-11 CERAMIC CHIP 0.01uF 50V C179 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V C180 1-128-065-11 ELECT 68uF 20% 10V
C111 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C181 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C112 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C182 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C113 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V C183 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C114 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C184 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V
C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V < CONNECTOR >

C117 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V CN101 1-565-728-11 CONNECTOR, FPC 17P
C118 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V CN102 1-770-298-31 HOUSING, CONNECTOR 28P
C119 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V CN104 1-580-055-21 PIN, CONNECTOR 2P
C120 1-135-201-11 TANTALUM CHIP 10uF 20% 4V CN105 1-774-417-11 CONNECTOR, FPC 5P
C121 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V CN106 1-770-345-21 CONNECTOR, FPC 7P

C122 1-164-232-11 CERAMIC CHIP 0.01uF 50V CN107 1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P
C123 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V < FERRITE BEAD >
C125 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C126 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V FB101 1-500-245-11 INDUCTOR 0UH
FB102 1-216-295-91 CONDUCTOR, CHIP (2012)
C127 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V FB103 1-500-245-11 INDUCTOR 0UH
C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V FB104 1-216-295-91 CONDUCTOR, CHIP (2012)
C129 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V FB105 1-414-386-11 INDUCTOR, FERRITE BEAD
C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C131 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V FB106 1-414-386-11 INDUCTOR, FERRITE BEAD

C132 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V < IC >

C133 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
C134 1-164-346-11 CERAMIC CHIP 1uF 16V IC101 8-752-069-56 IC CXA1782BQ
C135 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC102 8-759-291-06 IC BA6397FP
C136 1-164-005-11 CERAMIC CHIP 0.47uF 25V IC103 8-752-372-94 IC CXD2507AQ
IC104 8-759-185-29 IC PCM1710U-B
C137 1-164-232-11 CERAMIC CHIP 0.01uF 50V IC105 8-759-823-87 IC LB1638M
C139 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C140 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C141 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C142 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V

Downloaded from www.Manualslib.com manuals search engine

— 51 —
 BD EJECT FUNCTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< TRANSISTOR > R156 1-216-085-00 METAL CHIP 33K 5% 1/10W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
Q1 8-729-032-35 PHOTO TRANSISTOR CPT-230S-C-TU R158 1-216-001-00 METAL CHIP 10 5% 1/10W
Q2 8-729-032-35 PHOTO TRANSISTOR CPT-230S-C-TU R171 1-216-049-91 METAL GLAZE 1K 5% 1/10W
Q4 8-729-032-35 PHOTO TRANSISTOR CPT-230S-C-TU R172 1-216-049-91 METAL GLAZE 1K 5% 1/10W
Q101 8-729-010-08 TRANSISTOR MSB710-R
Q102 8-729-424-08 TRANSISTOR UN2111 R173 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R174 1-216-049-91 METAL GLAZE 1K 5% 1/10W
< RESISTOR > R175 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R176 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R102 1-216-001-00 METAL CHIP 10 5% 1/10W R177 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R103 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R104 1-216-097-91 METAL GLAZE 100K 5% 1/10W R183 1-216-105-91 METAL GLAZE 220K 5% 1/10W
R105 1-216-093-00 METAL CHIP 68K 5% 1/10W R184 1-216-105-91 METAL GLAZE 220K 5% 1/10W
R106 1-216-093-00 METAL CHIP 68K 5% 1/10W R185 1-216-105-91 METAL GLAZE 220K 5% 1/10W
R186 1-216-295-91 CONDUCTOR, CHIP (2012)
R107 1-216-093-00 METAL CHIP 68K 5% 1/10W R187 1-216-295-91 CONDUCTOR, CHIP (2012)
R108 1-216-093-00 METAL CHIP 68K 5% 1/10W
R109 1-216-097-91 METAL GLAZE 100K 5% 1/10W R188 1-216-295-91 CONDUCTOR, CHIP (2012)
R112 1-216-083-00 METAL CHIP 27K 5% 1/10W R189 1-216-295-91 CONDUCTOR, CHIP (2012)
R113 1-216-083-00 METAL CHIP 27K 5% 1/10W
< VARIABLE RESISTOR >
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W
R115 1-216-101-00 METAL CHIP 150K 5% 1/10W RV101 1-223-587-11 RES, ADJ, CARBON 22K
R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W RV102 1-223-587-11 RES, ADJ, CARBON 22K
R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W RV103 1-223-587-11 RES, ADJ, CARBON 22K
R118 1-216-049-91 METAL GLAZE 1K 5% 1/10W
< SWITCH >
R119 1-216-089-91 METAL GLAZE 47K 5% 1/10W
R120 1-216-089-91 METAL GLAZE 47K 5% 1/10W S1 1-571-754-31 SWITCH, PUSH (1 KEY)
R121 1-216-114-00 METAL GLAZE 510K 5% 1/10W
R122 1-216-097-91 METAL GLAZE 100K 5% 1/10W < VIBRATOR >
R123 1-216-097-91 METAL GLAZE 100K 5% 1/10W
X101 1-767-430-11 VIBRATOR, CRYSTAL 16.9344MHz
R124 1-216-097-91 METAL GLAZE 100K 5% 1/10W
R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W ************************************************************
R126 1-216-061-00 METAL CHIP 3.3K 5% 1/10W * 1-667-388-11 EJECT BOARD
R127 1-216-097-91 METAL GLAZE 100K 5% 1/10W ***********
R128 1-216-105-91 METAL GLAZE 220K 5% 1/10W
< CONNECTOR >
R129 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W CN753 1-580-918-11 HOUSING, CONNECTOR 5P
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W
R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < SWITCH >
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
S755 1-762-875-21 SWITCH, KEYBOARD (6OPEN/CLOSE)
R134 1-216-065-00 METAL CHIP 4.7K 5% 1/10W ************************************************************
R135 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W * A-4403-553-A FUNCTION BOARD, COMPLETE (AEP,G)
R137 1-216-065-00 METAL CHIP 4.7K 5% 1/10W *************************
R138 1-216-049-91 METAL GLAZE 1K 5% 1/10W A-4403-536-A FUNCTION BOARD, COMPLETE (SP,MY,HK,JE)
*************************
R139 1-216-033-00 METAL CHIP 220 5% 1/10W * A-4403-726-A FUNCTION BOARD, COMPLETE (UK)
R140 1-216-081-00 METAL CHIP 22K 5% 1/10W *************************
R141 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R142 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < CAPACITOR >
R143 1-216-121-91 METAL GLAZE 1M 5% 1/10W
C401 1-162-282-31 CERAMIC 100PF 10% 50V
R144 1-216-073-00 METAL CHIP 10K 5% 1/10W (AEP,G,UK)
R145 1-216-097-91 METAL GLAZE 100K 5% 1/10W C402 1-126-791-11 ELECT 10uF 20% 35V
R146 1-216-097-91 METAL GLAZE 100K 5% 1/10W C403 1-162-282-31 CERAMIC 100PF 10% 50V
R147 1-216-049-91 METAL GLAZE 1K 5% 1/10W (AEP,G,UK)
R148 1-216-049-91 METAL GLAZE 1K 5% 1/10W
C404 1-162-282-31 CERAMIC 100PF 10% 50V
R149 1-216-049-91 METAL GLAZE 1K 5% 1/10W (AEP,G,UK)
R150 1-216-037-00 METAL CHIP 330 5% 1/10W C405 1-162-282-31 CERAMIC 100PF 10% 50V
R151 1-216-037-00 METAL CHIP 330 5% 1/10W (AEP,G,UK)
R152 1-216-037-00 METAL CHIP 330 5% 1/10W C406 1-126-791-11 ELECT 10uF 20% 35V
R154 1-216-065-00 METAL CHIP 4.7K 5% 1/10W

Downloaded from www.Manualslib.com manuals search engine

— 52 —
 FUNCTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C407 1-162-282-31 CERAMIC 100PF 10% 50V < TRANSISTOR >
(AEP,G,UK)
C408 1-162-282-31 CERAMIC 100PF 10% 50V Q401 8-729-422-57 TRANSISTOR UN4111
(AEP,G,UK) Q404 8-729-620-05 TRANSISTOR 2SC2603-EF
C426 1-164-159-11 CERAMIC 0.1uF 50V
C430 1-164-159-11 CERAMIC 0.1uF 50V < RESISTOR >
C431 1-164-159-11 CERAMIC 0.1uF 50V
R401 1-249-426-11 CARBON 5.6K 5% 1/4W
C432 1-126-059-11 ELECT 10uF 20% 50V R402 1-249-427-11 CARBON 6.8K 5% 1/4W F
C433 1-126-059-11 ELECT 10uF 20% 50V R403 1-249-413-11 CARBON 470 5% 1/4W F
C436 1-164-159-11 CERAMIC 0.1uF 50V R404 1-249-441-11 CARBON 100K 5% 1/4W
C437 1-126-934-11 ELECT 220uF 20% 16V R405 1-249-413-11 CARBON 470 5% 1/4W F
C438 1-164-159-11 CERAMIC 0.1uF 50V
R407 1-249-417-11 CARBON 1K 5% 1/4W F
C450 1-164-159-11 CERAMIC 0.1uF 50V R408 1-249-441-11 CARBON 100K 5% 1/4W
C451 1-161-494-00 CERAMIC 0.022uF 25V R409 1-249-409-11 CARBON 220 5% 1/4W F
C493 1-164-159-11 CERAMIC 0.1uF 50V R410 1-249-441-11 CARBON 100K 5% 1/4W
C501 1-162-282-31 CERAMIC 100PF 10% 50V R411 1-249-409-11 CARBON 220 5% 1/4W F
(AEP,G,UK)
C502 1-126-791-11 ELECT 10uF 20% 35V R412 1-249-441-11 CARBON 100K 5% 1/4W
C503 1-162-282-31 CERAMIC 100PF 10% 50V R415 1-249-437-11 CARBON 47K 5% 1/4W
(AEP,G,UK) R416 1-249-437-11 CARBON 47K 5% 1/4W
C504 1-162-282-31 CERAMIC 100PF 10% 50V R417 1-249-437-11 CARBON 47K 5% 1/4W
(AEP,G,UK) R418 1-249-433-11 CARBON 22K 5% 1/4W
C505 1-162-282-31 CERAMIC 100PF 10% 50V
(AEP,G,UK) R430 1-247-807-31 CARBON 100 5% 1/4W
C506 1-126-791-11 ELECT 10uF 20% 35V R431 1-249-417-11 CARBON 1K 5% 1/4W F
C507 1-162-282-31 CERAMIC 100PF 10% 50V R432 1-249-393-11 CARBON 10 5% 1/4W F
(AEP,G,UK) R433 1-249-429-11 CARBON 10K 5% 1/4W
C508 1-162-282-31 CERAMIC 100PF 10% 50V R434 1-260-095-11 CARBON 470 5% 1/2W
(AEP,G,UK)
R435 1-249-433-11 CARBON 22K 5% 1/4W
< CONNECTOR > R436 1-249-433-11 CARBON 22K 5% 1/4W
R437 1-247-807-31 CARBON 100 5% 1/4W
CN401 1-770-406-11 CONNECTOR, BOARD TO BOARD 10P R438 1-247-807-31 CARBON 100 5% 1/4W
CN402 1-779-968-11 SOCKET, CONNECTOR R439 1-247-807-31 CARBON 100 5% 1/4W
* CN403 1-774-813-11 CONNECTOR, BOARD TO BOARD 7P(AEP,G,UK)
* CN404 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P R440 1-247-807-31 CARBON 100 5% 1/4W
CN407 1-770-408-11 CONNECTOR, BOARD TO BOARD 14P R441 1-247-807-31 CARBON 100 5% 1/4W
R461 1-247-843-11 CARBON 3.3K 5% 1/4W
CN410 1-778-310-11 PLUG, CONNECTOR 2P R462 1-249-429-11 CARBON 10K 5% 1/4W
R495 1-247-843-11 CARBON 3.3K 5% 1/4W
< JACK >
R501 1-249-426-11 CARBON 5.6K 5% 1/4W
CNJ401 1-770-501-11 JACK 10P (MD) R502 1-249-427-11 CARBON 6.8K 5% 1/4W F
CNJ402 1-770-501-11 JACK 10P (TAPE) R503 1-249-413-11 CARBON 470 5% 1/4W F
R504 1-249-441-11 CARBON 100K 5% 1/4W
< DIODE > R505 1-249-413-11 CARBON 470 5% 1/4W F

D401 8-719-911-19 DIODE 1SS119 R507 1-249-417-11 CARBON 1K 5% 1/4W F

D402 8-719-911-19 DIODE 1SS119 R508 1-249-441-11 CARBON 100K 5% 1/4W
D403 8-719-911-19 DIODE 1SS119 R509 1-249-409-11 CARBON 220 5% 1/4W F
D404 8-719-933-39 DIODE HZS6C1L R510 1-249-441-11 CARBON 100K 5% 1/4W
D405 8-719-911-19 DIODE 1SS119 R511 1-249-409-11 CARBON 220 5% 1/4W F

D406 8-719-911-19 DIODE 1SS119 (AEP,G,UK) R512 1-249-441-11 CARBON 100K 5% 1/4W
D407 8-719-911-19 DIODE 1SS119 (AEP,G,UK) R561 1-247-843-11 CARBON 3.3K 5% 1/4W
D408 8-719-911-19 DIODE 1SS119 (AEP,G,UK) R562 1-249-429-11 CARBON 10K 5% 1/4W

< IC > < TUNER UNIT >

IC401 8-759-195-14 IC SC027MG051BCP TB401 1-233-654-11 ENCAPSULATED COMPONENT (SP,MY,HK,JE)

IC402 8-759-195-21 IC SC027MG066BF-T1 TB401 1-234-028-11 ENCAPSULATED COMPONENT (UK)
IC403 8-759-195-21 IC SC027MG066BF-T1 TB401 1-693-377-11 TUNER (AEP,G)
IC501 8-759-195-14 IC SC027MG051BCP ************************************************************

< JACK >

J401 1-573-028-31 JACK, PIN 4P

(VIDEO/PC(L-IN,L-OUT,R-IN,R-OUT))
J402 1-779-940-11 CONNECTOR, COAXIAL
(ANTENNA(AM,FM75 ))

Downloaded from www.Manualslib.com manuals search engine

— 53 —
 HP MOTOR PANEL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-667-387-11 HP BOARD C727 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
********* C728 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C729 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< CAPACITOR > C730 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C731 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C491 1-162-294-31 CERAMIC 0.001uF 10% 50V
C591 1-162-294-31 CERAMIC 0.001uF 10% 50V C751 1-126-154-11 ELECT 47uF 20% 6.3V
C752 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< JACK >
< CONNECTOR >
J660 1-764-106-21 JACK (PHONES)
************************************************************ * CN701 1-568-842-11 SOCKET, CONNECTOR 27P
CN702 1-779-970-11 PLUG, CONNECTOR
* 1-653-379-51 MOTOR BOARD CN703 1-779-938-11 CONNECTOR, BOARD TO BOARD 8P
************* CN752 1-580-918-11 HOUSING, CONNECTOR 5P

< JACK > < DIODE >

CNJ303 1-770-348-21 CONNECTOR, FPC 7P D701 8-719-016-74 DIODE 1SS352

D702 8-719-016-74 DIODE 1SS352
< SWITCH > D703 8-719-210-33 DIODE EC10DS2
D704 8-719-210-33 DIODE EC10DS2
S301 1-571-754-31 SWITCH, PUSH (1 KEY)
************************************************************ < FILTER >

* A-4403-540-A PANEL BOARD, COMPLETE (SP,MY,HK,JE) FL701 1-517-701-11 INDICATOR TUBE, FLUORESCENT
**********************
* A-4403-560-A PANEL BOARD, COMPLETE (AEP,G) < IC >
**********************
* A-4403-727-A PANEL BOARD, COMPLETE (UK) IC701 8-759-481-03 IC uPD780206GF-023-3BA
********************** IC751 8-759-459-84 IC NJL56H400 (REMOTE SENSOR)
IC850 8-759-165-80 IC PST600C-T
* 4-932-810-11 CUSHION (FL)
* 4-994-815-01 HOLDER (FL) < COIL >

< CAPACITOR > L701 1-412-344-41 INDUCTOR 22uH

C701 1-165-319-11 CERAMIC CHIP 0.1uF 50V < TRANSISTOR >

C702 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C703 1-126-157-11 ELECT 10uF 20% 16V Q701 8-729-424-59 TRANSISTOR UN2212
C704 1-124-584-00 ELECT 100uF 20% 10V Q704 8-729-421-22 TRANSISTOR UN2211
C705 1-104-905-11 CAPACITOR 0.22F 5.5V
< RESISTOR >
C706 1-126-157-11 ELECT 10uF 20% 16V
C707 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V R701 1-216-073-00 METAL CHIP 10K 5% 1/10W
C708 1-165-319-11 CERAMIC CHIP 0.1uF 50V R702 1-216-073-00 METAL CHIP 10K 5% 1/10W
C709 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V R704 1-216-073-00 METAL CHIP 10K 5% 1/10W
C710 1-101-004-00 CERAMIC 0.01uF 50V R706 1-216-025-91 METAL GLAZE 100 5% 1/10W
R707 1-216-029-00 METAL CHIP 150 5% 1/10W
C711 1-102-958-00 CERAMIC 20PF 5% 50V
C712 1-102-958-00 CERAMIC 20PF 5% 50V R708 1-216-089-91 METAL GLAZE 47K 5% 1/10W
C713 1-165-319-11 CERAMIC CHIP 0.1uF 50V R709 1-216-089-91 METAL GLAZE 47K 5% 1/10W
C715 1-165-319-11 CERAMIC CHIP 0.1uF 50V R710 1-216-025-91 METAL GLAZE 100 5% 1/10W
C716 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R711 1-216-025-91 METAL GLAZE 100 5% 1/10W
R712 1-216-025-91 METAL GLAZE 100 5% 1/10W
C717 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C718 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R713 1-216-025-91 METAL GLAZE 100 5% 1/10W
C719 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R714 1-216-025-91 METAL GLAZE 100 5% 1/10W
C720 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R715 1-216-025-91 METAL GLAZE 100 5% 1/10W
C721 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R716 1-216-025-91 METAL GLAZE 100 5% 1/10W
R717 1-216-025-91 METAL GLAZE 100 5% 1/10W
C722 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C723 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R718 1-216-025-91 METAL GLAZE 100 5% 1/10W
C724 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R719 1-216-025-91 METAL GLAZE 100 5% 1/10W
C725 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R720 1-216-025-91 METAL GLAZE 100 5% 1/10W
C726 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R721 1-216-017-91 METAL GLAZE 47 5% 1/10W
R722 1-216-017-91 METAL GLAZE 47 5% 1/10W

Downloaded from www.Manualslib.com manuals search engine

— 54 —
 PANEL POSISTOR POWER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R723 1-216-025-91 METAL GLAZE 100 5% 1/10W * 1-668-138-11 POSISTOR BOARD
R724 1-216-017-91 METAL GLAZE 47 5% 1/10W ***************
R725 1-216-017-91 METAL GLAZE 47 5% 1/10W
R726 1-216-025-91 METAL GLAZE 100 5% 1/10W < CAPACITOR >
R727 1-216-085-00 METAL CHIP 33K 5% 1/10W
C915 1-164-159-11 CERAMIC 0.1uF 50V
R728 1-216-085-00 METAL CHIP 33K 5% 1/10W C916 1-164-159-11 CERAMIC 0.1uF 50V
R729 1-216-025-91 METAL GLAZE 100 5% 1/10W
R730 1-216-025-91 METAL GLAZE 100 5% 1/10W < CONNECTOR >
R731 1-216-025-91 METAL GLAZE 100 5% 1/10W
R732 1-216-025-91 METAL GLAZE 100 5% 1/10W * CN911 1-564-521-11 PLUG, CONNECTOR

R733 1-216-025-91 METAL GLAZE 100 5% 1/10W < THERMISTOR >

R734 1-216-073-00 METAL CHIP 10K 5% 1/10W
R735 1-216-065-00 METAL CHIP 4.7K 5% 1/10W THP901 1-801-671-11 THERMISTOR, POSITIVE
R736 1-216-073-00 METAL CHIP 10K 5% 1/10W THP902 1-801-671-11 THERMISTOR, POSITIVE
R737 1-216-025-91 METAL GLAZE 100 5% 1/10W THP903 1-801-671-11 THERMISTOR, POSITIVE
THP904 1-801-671-11 THERMISTOR, POSITIVE
R738 1-216-025-91 METAL GLAZE 100 5% 1/10W ************************************************************
R739 1-216-025-91 METAL GLAZE 100 5% 1/10W
R740 1-216-075-00 METAL CHIP 12K 5% 1/10W * A-4403-537-A POWER BOARD, COMPLETE (SP,MY,HK,JE)
(UK) ***********************
R740 1-216-077-00 METAL CHIP 15K 5% 1/10W * A-4403-555-A POWER BOARD, COMPLETE (AEP,G,UK)
(SP,MY,HK,JE) ***********************
R740 1-216-081-00 METAL CHIP 22K 5% 1/10W
(AEP,G) < CAPACITOR >

R741 1-216-065-00 METAL CHIP 4.7K 5% 1/10W C801 1-126-043-11 ELECT 0.47uF 20% 50V
(SP,MY,HK,JE) C803 1-126-868-11 ELECT 47uF 20% 50V
R741 1-216-085-00 METAL CHIP 33K 5% 1/10W C805 1-164-159-11 CERAMIC 0.1uF 50V
(AEP,G,UK) (AEP,G,UK)
R742 1-216-109-00 METAL CHIP 330K 5% 1/10W C810 1-126-933-11 ELECT 100uF 20% 16V
C811 1-126-967-11 ELECT 47uF 20% 50V
R743 1-216-041-00 METAL CHIP 470 5% 1/10W
R744 1-216-041-00 METAL CHIP 470 5% 1/10W C851 1-126-043-11 ELECT 0.47uF 20% 50V
R745 1-216-025-91 METAL GLAZE 100 5% 1/10W C853 1-126-868-11 ELECT 47uF 20% 50V
R746 1-216-025-91 METAL GLAZE 100 5% 1/10W C855 1-164-159-11 CERAMIC 0.1uF 50V
R755 1-216-065-00 METAL CHIP 4.7K 5% 1/10W (AEP,G,UK)
C893 1-126-868-11 ELECT 47uF 20% 50V
R756 1-216-097-91 METAL GLAZE 100K 5% 1/10W
R757 1-216-089-91 METAL GLAZE 47K 5% 1/10W C894 1-126-868-11 ELECT 47uF 20% 50V
R758 1-216-089-91 METAL GLAZE 47K 5% 1/10W C901 1-126-029-11 ELECT 3300uF 20% 25V
R759 1-216-089-91 METAL GLAZE 47K 5% 1/10W C902 1-126-029-11 ELECT 3300uF 20% 25V
R760 1-216-089-91 METAL GLAZE 47K 5% 1/10W C903 1-126-943-11 ELECT 2200uF 20% 25V
C905 1-126-376-11 ELECT 470uF 20% 25V
R771 1-216-025-91 METAL GLAZE 100 5% 1/10W
(AEP,G) C906 1-126-233-11 ELECT 22uF 20% 50V
R772 1-216-025-91 METAL GLAZE 100 5% 1/10W C908 1-136-165-00 FILM 0.1uF 5% 50V
(SP,MY,HK,JE) C909 1-136-165-00 FILM 0.1uF 5% 50V
R773 1-216-025-91 METAL GLAZE 100 5% 1/10W C911 1-126-868-11 ELECT 47uF 20% 50V
(UK) C912 1-164-159-11 CERAMIC 0.1uF 50V

< SWITCH > C914 1-162-306-11 CERAMIC 0.01uF 20% 16V

C931 1-126-096-11 ELECT 10uF 20% 35V
S761 1-762-875-21 SWITCH, KEYBOARD (POWER) C932 1-126-096-11 ELECT 10uF 20% 35V
C933 1-126-096-11 ELECT 10uF 20% 35V
< VIBRATOR > C934 1-126-096-11 ELECT 10uF 20% 35V

X701 1-579-233-11 VIBRATOR, CERAMIC 5MHz C935 1-126-096-11 ELECT 10uF 20% 35V
X702 1-567-098-41 VIBRATOR, CRYSTAL 32KHz C936 1-126-096-11 ELECT 10uF 20% 35V
************************************************************ C937 1-164-159-11 CERAMIC 0.1uF 50V
C941 1-126-868-11 ELECT 47uF 20% 50V
C942 1-164-159-11 CERAMIC 0.1uF 50V

C943 1-126-052-11 ELECT 100uF 20% 35V

C951 1-164-159-11 CERAMIC 0.1uF 50V
C952 1-164-159-11 CERAMIC 0.1uF 50V
C960 1-126-025-11 ELECT 330uF 20% 16V
C961 1-162-306-11 CERAMIC 0.01uF 20% 16V

Downloaded from www.Manualslib.com manuals search engine

— 55 —
 POWER POWER IC
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C962 1-162-306-11 CERAMIC 0.01uF 20% 16V < RESISTOR >
C963 1-162-306-11 CERAMIC 0.01uF 20% 16V
C965 1-126-233-11 ELECT 22uF 20% 50V R801 1-249-417-11 CARBON 1K 5% 1/4W F
C966 1-164-159-11 CERAMIC 0.1uF 50V R802 1-247-870-11 CARBON 43K 5% 1/4W
C967 1-126-923-11 ELECT 220uF 20% 10V R803 1-249-417-11 CARBON 1K 5% 1/4W F
R807 1-260-091-11 CARBON 220 5% 1/2W
< CONNECTOR > R809 1-249-437-11 CARBON 47K 5% 1/4W

* CN802 1-569-493-11 SOCKET, CONNECTOR 7P R810 1-249-441-11 CARBON 100K 5% 1/4W

* CN806 1-562-334-00 SOCKET, CONNECTOR 10P R811 1-249-441-11 CARBON 100K 5% 1/4W
* CN908 1-506-469-11 PIN, CONNECTOR 4P R813 1-249-438-11 CARBON 56K 5% 1/4W
CN912 1-568-838-11 SOCKET, CONNECTOR 21P ! R814 1-219-122-91 FUSIBLE 0.33 5% 1/4W F
* CN913 1-770-656-11 CONNECTOR, FFC/FPC 28P R841 1-249-441-11 CARBON 100K 5% 1/4W

* CN916 1-568-842-11 SOCKET, CONNECTOR 27P R851 1-249-417-11 CARBON 1K 5% 1/4W F

* CN917 1-568-951-11 PIN, CONNECTOR 2P R852 1-247-870-11 CARBON 43K 5% 1/4W
R853 1-249-417-11 CARBON 1K 5% 1/4W F
< DIODE > R857 1-260-091-11 CARBON 220 5% 1/2W
R859 1-249-438-11 CARBON 56K 5% 1/4W
D801 8-719-911-19 DIODE 1SS119
D802 8-719-911-19 DIODE 1SS119 ! R901 1-208-737-51 FUSIBLE 2.2 5% 1/4W F
D803 8-719-911-19 DIODE 1SS119 ! R912 1-212-958-00 FUSIBLE 10 5% 1/2W F
D901 8-719-025-03 DIODE RBA-402-SL ! R915 1-219-122-91 FUSIBLE 0.33 5% 1/4W F
D902 8-719-200-02 DIODE 10E2 ! R916 1-219-122-91 FUSIBLE 0.33 5% 1/4W F
R931 1-249-421-11 CARBON 2.2K 5% 1/4W F
D903 8-719-200-02 DIODE 10E2
D904 8-719-200-82 DIODE 11ES2 R932 1-249-409-11 CARBON 220 5% 1/4W F
D905 8-719-200-82 DIODE 11ES2 R944 1-249-437-11 CARBON 47K 5% 1/4W
D906 8-719-200-82 DIODE 11ES2 R945 1-247-807-31 CARBON 100 5% 1/4W
D907 8-719-200-82 DIODE 11ES2 R946 1-247-807-31 CARBON 100 5% 1/4W
! R947 1-219-122-91 FUSIBLE 0.33 5% 1/4W F
D910 8-719-001-79 DIODE UZL-12H1-TP
D934 8-719-200-02 DIODE 10E2 < RELAY >
D935 8-719-200-02 DIODE 10E2
D936 8-719-200-02 DIODE 10E2 RY801 1-755-126-11 RELAY
D938 8-719-911-19 DIODE 1SS119
< THERMISTOR(POSITIVE) >
D941 8-719-933-39 DIODE HZS6C1L
THP801 1-801-829-11 THERMISTOR, POSITIVE
< TERMINAL > ************************************************************

EPT901 1-537-771-21 TERMINAL BOARD, GROUND * 1-667-823-11 POWER IC BOARD

***************
< IC >
< CAPACITOR >
IC802 8-759-165-80 IC PST600C-T
IC901 8-749-923-04 IC TOTX178 (CD OPTICAL DIGITAL OUT) C807 1-162-219-31 CERAMIC 68PF 5% 50V
IC931 8-759-231-53 IC TA7805S C831 1-164-159-11 CERAMIC 0.1uF 50V
IC932 8-759-604-86 IC M5F7807L C857 1-162-219-31 CERAMIC 68PF 5% 50V
IC933 8-759-231-53 IC TA7805S C881 1-164-159-11 CERAMIC 0.1uF 50V

IC941 8-759-633-42 IC M5293L < CONNECTOR >

< COIL > * CN805 1-506-608-11 PIN, CONNECTOR 10P

L901 1-408-413-00 INDUCTOR 22uH < IC >

L902 1-410-322-11 INDUCTOR 3.3uH
IC801 8-759-333-24 IC LM1876TF
< TRANSISTOR >
< RESISTOR >
Q801 8-729-900-80 TRANSISTOR DTC114ES
Q802 8-729-620-05 TRANSISTOR 2SC2603-EF R804 1-249-437-11 CARBON 47K 5% 1/4W
Q803 8-729-620-05 TRANSISTOR 2SC2603-EF R831 1-249-389-11 CARBON 4.7 5% 1/4W F
Q804 8-729-620-05 TRANSISTOR 2SC2603-EF R854 1-249-437-11 CARBON 47K 5% 1/4W
Q805 8-729-422-57 TRANSISTOR UN4111 R881 1-249-389-11 CARBON 4.7 5% 1/4W F
************************************************************
Q910 8-729-202-67 TRANSISTOR 2SK246-GR3
Q911 8-729-021-82 TRANSISTOR 2SD2396K
Q931 8-729-140-97 TRANSISTOR 2SB734-34

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
— 56 —
 PRE
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* A-4403-527-A PRE BOARD, COMPLETE < CONNECTOR >
********************
CN420 1-770-383-11 CONNECTOR, BOARD TO BOARD 14P
< CAPACITOR > * CN421 1-568-864-11 SOCKET, CONNECTOR 21P
CN422 1-770-381-11 CONNECTOR, BOARD TO BOARD 10P
C409 1-126-233-11 ELECT 22uF 20% 50V CN423 1-564-707-11 PIN, CONNECTOR (SMALL TYPE) 5P
C410 1-126-233-11 ELECT 22uF 20% 50V
C411 1-162-207-31 CERAMIC 22PF 5% 50V < DIODE >
C412 1-136-177-00 FILM 1uF 5% 50V
C413 1-136-177-00 FILM 1uF 5% 50V D921 8-719-001-21 DIODE UZL-9H1
D922 8-719-001-21 DIODE UZL-9H1
C414 1-126-961-11 ELECT 2.2uF 20% 50V
C415 1-137-364-11 FILM 0.001uF 5% 50V < IC >
C416 1-136-165-00 FILM 0.1uF 5% 50V
C417 1-126-233-11 ELECT 22uF 20% 50V IC404 8-759-711-35 IC NJM4580D
C421 1-126-233-11 ELECT 22uF 20% 50V IC410 8-759-275-23 IC BU2092
IC422 8-759-195-20 IC SC027MG066BCP
C422 1-164-159-11 CERAMIC 0.1uF 50V IC423 8-759-195-16 IC SC027MG052BCP
C423 1-164-159-11 CERAMIC 0.1uF 50V IC424 8-759-070-78 IC TC9211P
C439 1-126-514-11 ELECT 22uF 20% 16V
C440 1-136-162-00 FILM 0.056uF 5% 50V IC430 8-759-711-35 IC NJM4580D
C449 1-162-302-11 CERAMIC 0.0022uF 30% 16V IC530 8-759-711-35 IC NJM4580D

C452 1-162-306-11 CERAMIC 0.01uF 20% 16V < TRANSISTOR >

C471 1-164-159-11 CERAMIC 0.1uF 50V
C472 1-126-795-11 ELECT 10uF 20% 50V Q420 8-729-422-57 TRANSISTOR UN4111
C473 1-126-059-11 ELECT 10uF 20% 50V Q421 8-729-422-57 TRANSISTOR UN4111
C474 1-126-059-11 ELECT 10uF 20% 50V Q422 8-729-900-80 TRANSISTOR DTC114ES
Q424 8-729-141-30 TRANSISTOR 2SC3623A-LK
C475 1-126-059-11 ELECT 10uF 20% 50V Q524 8-729-141-30 TRANSISTOR 2SC3623A-LK
C476 1-164-159-11 CERAMIC 0.1uF 50V
C477 1-126-059-11 ELECT 10uF 20% 50V Q921 8-729-140-96 TRANSISTOR 2SD774-34
C478 1-164-159-11 CERAMIC 0.1uF 50V Q924 8-729-140-97 TRANSISTOR 2SB734-34
C479 1-162-294-31 CERAMIC 0.001uF 10% 50V
< RESISTOR >
C481 1-162-290-31 CERAMIC 470PF 10% 50V
C482 1-164-159-11 CERAMIC 0.1uF 50V R421 1-249-437-11 CARBON 47K 5% 1/4W
C483 1-164-159-11 CERAMIC 0.1uF 50V R422 1-249-441-11 CARBON 100K 5% 1/4W
C509 1-126-233-11 ELECT 22uF 20% 50V R423 1-249-417-11 CARBON 1K 5% 1/4W F
C510 1-126-233-11 ELECT 22uF 20% 50V R424 1-249-429-11 CARBON 10K 5% 1/4W
R425 1-247-887-00 CARBON 220K 5% 1/4W
C511 1-162-207-31 CERAMIC 22PF 5% 50V
C512 1-136-177-00 FILM 1uF 5% 50V R426 1-249-442-11 CARBON 510 5% 1/4W
C513 1-136-177-00 FILM 1uF 5% 50V R427 1-247-858-11 CARBON 13K 5% 1/4W
C514 1-126-961-11 ELECT 2.2uF 20% 50V R428 1-249-421-11 CARBON 2.2K 5% 1/4W F
C515 1-137-364-11 FILM 0.001uF 5% 50V R429 1-249-429-11 CARBON 10K 5% 1/4W
R442 1-249-428-11 CARBON 8.2K 5% 1/4W F
C516 1-136-165-00 FILM 0.1uF 5% 50V
C517 1-126-233-11 ELECT 22uF 20% 50V R443 1-247-887-00 CARBON 220K 5% 1/4W
C521 1-126-233-11 ELECT 22uF 20% 50V R444 1-249-437-11 CARBON 47K 5% 1/4W
C522 1-162-306-11 CERAMIC 0.01uF 20% 16V R445 1-249-431-11 CARBON 15K 5% 1/4W
C523 1-162-306-11 CERAMIC 0.01uF 20% 16V R446 1-249-435-11 CARBON 33K 5% 1/4W
R448 1-249-435-11 CARBON 33K 5% 1/4W
C539 1-126-514-11 ELECT 22uF 20% 16V
C540 1-136-162-00 FILM 0.056uF 5% 50V R449 1-249-421-11 CARBON 2.2K 5% 1/4W F
C549 1-162-302-11 CERAMIC 0.0022uF 30% 16V R450 1-247-807-31 CARBON 100 5% 1/4W
C920 1-164-159-11 CERAMIC 0.1uF 50V R451 1-249-426-11 CARBON 5.6K 5% 1/4W
C921 1-164-159-11 CERAMIC 0.1uF 50V R460 1-247-887-00 CARBON 220K 5% 1/4W
R470 1-247-807-31 CARBON 100 5% 1/4W
C922 1-126-052-11 ELECT 100uF 20% 16V
C923 1-126-052-11 ELECT 100uF 20% 16V R472 1-247-807-31 CARBON 100 5% 1/4W
C924 1-126-023-11 ELECT 100uF 20% 25V R473 1-247-807-31 CARBON 100 5% 1/4W
C925 1-126-023-11 ELECT 100uF 20% 25V R474 1-247-807-31 CARBON 100 5% 1/4W
C926 1-126-052-11 ELECT 100uF 20% 16V R475 1-247-807-31 CARBON 100 5% 1/4W
R476 1-247-807-31 CARBON 100 5% 1/4W

R478 1-249-417-11 CARBON 1K 5% 1/4W F

R479 1-249-425-11 CARBON 4.7K 5% 1/4W F
R481 1-247-807-31 CARBON 100 5% 1/4W
R482 1-247-807-31 CARBON 100 5% 1/4W
R483 1-247-807-31 CARBON 100 5% 1/4W

Downloaded from www.Manualslib.com manuals search engine

— 57 —
 PRE RDS RELAY
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R484 1-247-807-31 CARBON 100 5% 1/4W < COIL >
R485 1-247-807-31 CARBON 100 5% 1/4W
R486 1-249-437-11 CARBON 47K 5% 1/4W L601 1-410-977-11 INDUCTOR 100uH
R487 1-249-437-11 CARBON 47K 5% 1/4W
R488 1-249-432-11 CARBON 18K 5% 1/4W < RESISTOR >

R489 1-249-437-11 CARBON 47K 5% 1/4W R601 1-249-401-11 CARBON 47 5% 1/4W F

R490 1-249-437-11 CARBON 47K 5% 1/4W R602 1-249-441-11 CARBON 100K 5% 1/4W
R491 1-249-413-11 CARBON 470 5% 1/4W F R603 1-249-441-11 CARBON 100K 5% 1/4W
R493 1-249-413-11 CARBON 470 5% 1/4W F R604 1-249-426-11 CARBON 5.6K 5% 1/4W
R494 1-249-413-11 CARBON 470 5% 1/4W F R605 1-249-429-11 CARBON 10K 5% 1/4W

R521 1-249-437-11 CARBON 47K 5% 1/4W R606 1-249-405-11 CARBON 100 5% 1/4W F
R522 1-249-441-11 CARBON 100K 5% 1/4W R607 1-249-417-11 CARBON 1K 5% 1/4W F
R523 1-249-417-11 CARBON 1K 5% 1/4W F
R524 1-249-429-11 CARBON 10K 5% 1/4W < VIBRATOR >
R525 1-247-887-00 CARBON 220K 5% 1/4W
X601 1-579-900-21 VIBRATOR, CRYSTAL 4.332MHz
R526 1-249-442-11 CARBON 510 5% 1/4W ************************************************************
R527 1-247-858-11 CARBON 13K 5% 1/4W
R528 1-249-421-11 CARBON 2.2K 5% 1/4W F * 1-667-822-11 RELAY BOARD
R529 1-249-429-11 CARBON 10K 5% 1/4W ************
R542 1-249-428-11 CARBON 8.2K 5% 1/4W F
< CAPACITOR >
R543 1-247-887-00 CARBON 220K 5% 1/4W
R544 1-249-437-11 CARBON 47K 5% 1/4W C820 1-126-794-11 ELECT 4.7uF 20% 50V
R545 1-249-431-11 CARBON 15K 5% 1/4W C821 1-126-177-11 ELECT 100uF 20% 10V
R546 1-249-435-11 CARBON 33K 5% 1/4W C822 1-164-159-11 CERAMIC 0.1uF 50V
R548 1-249-435-11 CARBON 33K 5% 1/4W C823 1-164-159-11 CERAMIC 0.1uF 50V
C824 1-164-159-11 CERAMIC 0.1uF 50V
R549 1-249-421-11 CARBON 2.2K 5% 1/4W F
R551 1-249-426-11 CARBON 5.6K 5% 1/4W < CONNECTOR >
R560 1-247-887-00 CARBON 220K 5% 1/4W
R921 1-247-843-11 CARBON 3.3K 5% 1/4W * CN812 1-569-502-11 PIN, CONNECTOR 7P
R925 1-247-843-11 CARBON 3.3K 5% 1/4W * CN813 1-691-174-11 CONNECTOR (BOARD TO BOARD) 4P
************************************************************ CN814 1-564-506-11 PLUG, CONNECTOR 3P

* A-4403-559-A RDS BOARD, COMPLETE (AEP,G,UK) < DIODE >

********************
D820 8-719-933-50 DIODE HZS7C2L
< CAPACITOR > D821 8-719-933-39 DIODE HZS6C1L
D822 8-719-911-19 DIODE 1SS119
C601 1-162-291-31 CERAMIC 560PF 10% 50V D823 8-719-911-19 DIODE 1SS119
C602 1-162-306-11 CERAMIC 0.01uF 20% 16V
C603 1-162-288-31 CERAMIC 330PF 10% 50V < TRANSISTOR >
C604 1-126-961-11 ELECT 2.2uF 20% 50V
C605 1-126-964-11 ELECT 10uF 20% 50V Q820 8-729-119-76 TRANSISTOR 2SA1175-HFE
C606 1-162-291-31 CERAMIC 560PF 10% 50V Q821 8-729-620-05 TRANSISTOR 2SC2603-EF
C607 1-126-964-11 ELECT 10uF 20% 50V Q822 8-729-620-05 TRANSISTOR 2SC2603-EF
C608 1-164-159-11 CERAMIC 0.1uF 50V Q823 8-729-620-05 TRANSISTOR 2SC2603-EF
C609 1-126-967-11 ELECT 47uF 20% 16V Q824 8-729-140-96 TRANSISTOR 2SD774-34
C610 1-102-518-11 CERAMIC 33PF 5% 50V
C611 1-102-518-11 CERAMIC 33PF 5% 50V < RESISTOR >
C612 1-162-306-11 CERAMIC 0.01uF 20% 16V
R820 1-249-417-11 CARBON 1K 5% 1/4W F
< CONNECTOR > R821 1-249-441-11 CARBON 100K 5% 1/4W
R822 1-249-429-11 CARBON 10K 5% 1/4W
CN601 1-779-939-11 CONNECTOR, BOARD TO BOARD 7P R823 1-249-441-11 CARBON 100K 5% 1/4W
R824 1-249-413-11 CARBON 470 5% 1/4W F
< DIODE >
! R825 1-212-966-00 FUSIBLE 22 5% 1/2W F
D601 8-719-911-19 DIODE 1SS119 R826 1-249-441-11 CARBON 100K 5% 1/4W
R827 1-249-441-11 CARBON 100K 5% 1/4W
< IC > R828 1-249-429-11 CARBON 10K 5% 1/4W
************************************************************
IC601 8-759-450-86 IC BU1922
IC602 8-759-634-51 IC M5218AP

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
— 58 —
 SENSOR SP TM SWITCH TRANS VOLSEL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-653-378-51 SENSOR BOARD < RESISTOR >
*************
R750 1-249-427-11 CARBON 6.8K 5% 1/4W F
< DIODE > R751 1-249-429-11 CARBON 10K 5% 1/4W
R752 1-247-858-11 CARBON 13K 5% 1/4W
D801 8-719-045-75 DIODE CL-200IR-X-TU R753 1-249-433-11 CARBON 22K 5% 1/4W
D803 8-719-045-75 DIODE CL-200IR-X-TU R762 1-249-425-11 CARBON 4.7K 5% 1/4W F
D804 8-719-045-75 DIODE CL-200IR-X-TU
R763 1-249-427-11 CARBON 6.8K 5% 1/4W F
< RESISTOR > R764 1-249-429-11 CARBON 10K 5% 1/4W
R765 1-247-858-11 CARBON 13K 5% 1/4W
R801 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R803 1-216-049-91 METAL GLAZE 1K 5% 1/10W < SWITCH >
R804 1-216-049-91 METAL GLAZE 1K 5% 1/10W
S751 1-762-875-21 SWITCH, KEYBOARD (DBFB)
< SWITCH > S752 1-762-875-21 SWITCH, KEYBOARD (VOL–)
S753 1-762-875-21 SWITCH, KEYBOARD (VOL+)
S802 1-692-441-11 SWITCH, MICROPHONE S754 1-762-875-21 SWITCH, KEYBOARD (FUNCTION)
************************************************************ S762 1-762-875-21 SWITCH, KEYBOARD (BAND)

* 1-667-386-11 SP TM BOARD S763 1-762-875-21 SWITCH, KEYBOARD (TUNE–/ 0 / =)

************ S764 1-762-875-21 SWITCH, KEYBOARD (TUNE+/ ) / + )
S765 1-762-875-21 SWITCH, KEYBOARD (flPLAY/PAUSE)
< CAPACITOR > S766 1-762-875-21 SWITCH, KEYBOARD (p)
************************************************************
C806 1-164-159-11 CERAMIC 0.1uF 50V
(AEP,G,UK) * 1-667-384-11 TRANS BOARD
C856 1-164-159-11 CERAMIC 0.1uF 50V ************
(AEP,G,UK)
1-533-293-11 FUSE HOLDER
< CONNECTOR >
< CONNECTOR >
CN803 1-691-161-11 PIN, CONNECTOR 4P
* CN902 1-573-047-11 PIN, CONNECTOR (PC BOARD) 2P
< COIL > CN905 1-691-770-11 PLUG (MICRO CONNECTOR) 8P

L801 1-420-872-00 COIL, AIR-CORE (AEP,G,UK) < FUSE >

L851 1-420-872-00 COIL, AIR-CORE (AEP,G,UK)
! F901 1-532-388-51 FUSE TIME, LAG 2A/250V
< RESISTOR > ************************************************************

R805 1-260-076-11 CARBON 10 5% 1/2W * 1-667-382-11 VOLSEL BOARD (MY, SP, HK, JE)
(AEP,G,UK) *************
R806 1-249-393-11 CARBON 10 5% 1/4W F
(AEP,G,UK) 1-533-293-11 FUSE HOLDER
R855 1-260-076-11 CARBON 10 5% 1/2W
(AEP,G,UK) < CONNECTOR >
R856 1-249-393-11 CARBON 10 5% 1/4W F
(AEP,G,UK) * CN920 1-564-507-11 PLUG, CONNECTOR 4P

< TERMINAL > < FUSE >

TM801 1-537-238-31 TERMINAL BOARD ! F902 1-532-505-51 FUSE TIME, LAG 5A/250V
(SPEAKER IMPEDANCE USE 4-16 (L+,L-,R+,R-)) ! F903 1-532-505-51 FUSE TIME, LAG 5A/250V
************************************************************
< SWITCH >
* 1-667-385-11 SWITCH BOARD
************* ! S901 1-554-752-11 SELECTOR, POWER VOLTAGE
(VOLTAGE SELECTOR)
< CONNECTOR > ************************************************************

CN751 1-766-928-11 CONNECTOR, BOARD TO BOARD 8P

< DIODE >

D751 8-719-056-12 DIODE SML79420C-TP4 (PLAY/PAUSE)

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
Downloaded from www.Manualslib.com manuals search engine
— 59 —
 HCD-101

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
MISCELLANEOUS **************
************** HARDWARE LIST
**************
13 1-782-805-11 WIRE (FLAT TYPE) (5 CORE)
14 1-782-781-11 WIRE (FLAT TYPE) (27 CORE) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
54 1-782-780-11 WIRE (FLAT TYPE) (21 CORE) #2 7-685-871-09 SCREW +BVTT 3X6 (S)
58 1-698-997-11 FAN, DC #3 7-685-862-09 SCREW +BVTT 2.6X6 (S)
! 65 1-776-060-11 CORD, POWER (EXCEPT UK) #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
#5 7-685-871-01 SCREW +BVTT 3X6 (S)
! 65 1-776-061-21 CORD, POWER (UK)
! 72 1-569-008-11 ADAPTOR, CONVERSION 2P (SP,MY) #6 7-621-772-60 SCREW +B 2X12
! 73 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK) #7 7-627-852-17 +P 1.7X4
! 152 8-848-283-11 OPTICAL PICK-UP KSS-313A #8 7-627-553-37 SCREW , PRECISION +P2X3
M101 X-3367-484-2 MOTOR (SP) ASSY (SPINDLE) #9 7-627-553-67 SCREW , PRECISION +P2X5
#10 7-685-851-01 SCREW +BVTT 2X4 (S)
M102 A-3252-585-A MOTOR (SL) ASSY (SLED)
M103 A-3252-580-A MOTOR (L) ASSY (LOADING) The components identified by mark ! or dotted
! T901 1-431-559-11 TRANSFORMER, POWER (AEP,G,UK) line with mark ! are critical for safety.
!T901 1-431-560-11 TRANSFORMER, POWER (SP,MY,HK,JE) Replace only with part number specified.
************************************************************

Sony Corporation 97I1675-1

9-920-988-11 Home A&V Products Company Printed in Japan © 1997.9
Published by General Engineering Dept.

Downloaded from www.Manualslib.com manuals search engine

— 60 — (Shibaura)