REVELPROG-IS Manual
Uploaded by
Juan Carlos De Leon CoradoREVELPROG-IS Manual
Uploaded by
Juan Carlos De Leon CoradoREVELPROG IS
user manual
Last update (v1.8.4): 2021-02-26
www.REVELTRONICS.com
Please read user manual before using the device.
Contents
1. Technical data and requirements .......................................................... - 6 -
2. Features and applications ..................................................................... - 7 -
3. Installation of software and USB drivers ............................................... - 8 -
4. First steps with REVELPROG-IS application .......................................... - 9 -
4.1. User interface .................................................................................................................................................................................. - 9 -
4.2. Device programming ...................................................................................................................................................................... - 11 -
4.2.1. Reading .................................................................................................................................................................................. - 11 -
4.2.2. Writing .................................................................................................................................................................................... - 12 -
4.2.3. Erasing ................................................................................................................................................................................... - 12 -
4.3. HEX editor features (buffer editing) .................................................................................................................................................. - 13 -
4.3.1. HEX editor ............................................................................................................................................................................... - 13 -
4.3.2. Appearance ............................................................................................................................................................................. - 13 -
4.3.3. Fill buffer... ............................................................................................................................................................................. - 14 -
4.3.4. Patterns - export changes to file................................................................................................................................................. - 15 -
4.3.5. Swap bytes.............................................................................................................................................................................. - 15 -
4.3.6. Clear buffer or generate random buffer ....................................................................................................................................... - 16 -
4.3.7. CRC32 and Checksum-16 .......................................................................................................................................................... - 16 -
4.3.8. File format conversion: .bin <-> .hex ......................................................................................................................................... - 16 -
-2-
4.3.9. DiffChecker (file comparing) ...................................................................................................................................................... - 17 -
4.4. Additional features ......................................................................................................................................................................... - 18 -
4.4.1. Blank test ................................................................................................................................................................................ - 18 -
4.4.2. Compare with the buffer ........................................................................................................................................................... - 18 -
4.4.3. VPP selection ........................................................................................................................................................................... - 18 -
4.4.4. Device identification (Chip ID) for FLASH SPI, DATAFLASH and 1-wire devices ................................................................................. - 19 -
4.4.5. Quad SPI (QSPI) configuration for FLASH SPI .............................................................................................................................. - 19 -
4.4.6. SFP/QSFP/XFP Transceivers support ........................................................................................................................................... - 19 -
4.4.7. Auto backup ............................................................................................................................................................................ - 19 -
5. In-Circuit Serial Programming (ICSP) ................................................. - 20 -
5.1. Addressing in external circuit........................................................................................................................................................... - 20 -
5.2. Write protection in circuit (WP/PRE pin) ............................................................................................................................................ - 21 -
5.3. Power supply in external circuit ....................................................................................................................................................... - 21 -
5.4. Limits and possible issues during in-circuit programming .................................................................................................................... - 22 -
5.5. SOIC Clip ...................................................................................................................................................................................... - 23 -
5.6. Troubleshooting for in-circuit programming ....................................................................................................................................... - 25 -
6. Custom Script Programming (I2C / SPI / 1-wire bus) ........................ - 27 -
6.1. Script construction ......................................................................................................................................................................... - 27 -
6.2. Script syntax ................................................................................................................................................................................. - 28 -
6.3. Script maker with GUI .................................................................................................................................................................... - 28 -
6.4. Script execution sequence ............................................................................................................................................................... - 29 -
-3-
6.5. Script examples ............................................................................................................................................................................. - 29 -
7. SFP / QSFP / XFP transceivers ............................................................ - 30 -
7.1. Adapter connection ........................................................................................................................................................................ - 30 -
7.2. Device selection and memory map ................................................................................................................................................... - 31 -
7.2.1. SFP and SFP+ .......................................................................................................................................................................... - 31 -
7.2.2. QSFP and QSFP+ ...................................................................................................................................................................... - 32 -
7.2.3. XFP ........................................................................................................................................................................................ - 33 -
7.3. Protected transceivers: manufacturer password and host password...................................................................................................... - 33 -
7.3.1. Host/User password .................................................................................................................................................................. - 34 -
7.3.2. Manufacturer password ............................................................................................................................................................. - 34 -
7.3.3. Hacking password (brute-force method) ...................................................................................................................................... - 34 -
8. Updates ............................................................................................... - 35 -
9. Research and development ................................................................. - 36 -
10. APPENDIX A - List of supported devices.............................................. - 37 -
9.1. EEPROM I2C 24… series .................................................................................................................................................................. - 37 -
9.2. EEPROM SPI 25… series .................................................................................................................................................................. - 39 -
9.3. EEPROM SPI 35… series .................................................................................................................................................................. - 40 -
9.4. EEPROM SPI 90… series .................................................................................................................................................................. - 40 -
9.5. EEPROM SPI 95… series .................................................................................................................................................................. - 40 -
9.6. EEPROM MICROWIRE 93… series...................................................................................................................................................... - 40 -
9.7. EEPROM 1-Wire ............................................................................................................................................................................. - 42 -
-4-
9.8. FLASH SPI 25… series ..................................................................................................................................................................... - 43 -
9.9. FLASH SPI 26… series ..................................................................................................................................................................... - 45 -
9.10. FLASH SPI 45… series (DATA FLASH) .............................................................................................................................................. - 45 -
9.11. FLASH SPI NAND.......................................................................................................................................................................... - 45 -
9.12. FRAM I2C 24… series .................................................................................................................................................................... - 46 -
9.13. FRAM SPI 25… series .................................................................................................................................................................... - 46 -
9.14. Optical and ethernet modules (SFP/SFP+ transceivers) ..................................................................................................................... - 46 -
9.15. Your suggestions .......................................................................................................................................................................... - 47 -
11. APPENDIX B - video tutorials and technical support ........................... - 48 -
-5-
1. Technical data and requirements
REVELPROG-IS made by REVELTRONICS is a professional tool for serial memory programming. It supports wide range of EEPROM, FLASH and
FRAM devices with I2C, SPI, 1-wire and Wire protocols powered with 1.0V - 5.0V voltage levels. It has integrated ZIF socket (for THT devices)
and SOIC socket (for SMD devices). It has also connector for in-circuit serial programming (ICSP) with buffered I/O. Due to USB 2.0 interface
memory operations are really fast.
Technical data:
• power supply and communication via USB 2.0 (hardware level, bulk transfer),
• supported protocols: I2C, SPI, 1-WIRE, MICROWIRE,
• supported devices with 1.0V - 5.0V power supply,
• programming device powered from programmer (1.0 - 5.0V, Imax = 100mA) or from external circuit (1.0 - 5.5V),
• operation speed (read/write) up to 10Mbit/s,
• ZIF-32 + SOIC-8 (150mil) integrated sockets,
• connector for in-circuit serial programming (ICSP) with buffered I/O,
• auto adaptive I/O pins connected only for programming time (Hi-Z in IDLE state),
• short circuit and overload protection,
• device manufactured in EU, made in Poland.
Requirements:
• USB 2.0 or above,
• Windows XP, Vista, 7, 8 or 10 (32 and 64 bit) + .NET Framework 41 installed in OS.
1
.NET 4.0 Client Profile can be downloaded from MICROSOFT: http://www.microsoft.com/en-us/download/details.aspx?id=17718
-6-
2. Features and applications
REVELPROG-IS is used in many applications such as: car electronics & automotive (reprogramming modules, radio-code, mileage correction,
immobilizers, gps navigations), computer service (data recovery, reflashing/upgrading/programming BIOS chips on motherboards of PC, notebooks,
copier & fax machines, printers, SFP/QSFP/XFP transceivers etc.), RTV/AGD service (TV & TV tuners, digital cameras, multifunction devices etc.) and
many other devices equipped with serial I2C/SPI/MICROWIRE EEPROM and FLASH chips. Due to the possibility of change voltage level (in range of 1.0
- 5.0V) programmer supports both older and newer devices (e.g. latest devices equipped with 1.2V and 1.8V low-voltage chips). Device is equipped
with ICSP connector that allows in-circuit serial programming without unsoldering the chip from board - built in additional protection (buffered
I/O, short circuit and overload protection) increase reliability and safety of such operations.
Main features:
• reading / writing / erasing functions with user-friendly application interface,
• supported binary files (*.bin, *.rom, *.epp etc.) and Intel-Hex (*.hex) with possibility to load file to the buffer, edit it, calculate checksums,
swap-bytes, save modified bytes as patterns, compare with chip etc.,
• programming in socket or in external circuit (without unsoldering the chip),
• the target application device can be either powered by REVELPROG (possibility to change VPP and logic levels: 1.0V / 1.5V / 1.8V / 2.5V /
2.8V / 3.3V / 5.0V) or powered by an application with external power supply (1.0 – 5.5V),
• build in additional protection: buffered I/O pins internal connected only during programming + short circuit and overload protection (reduces
the risk of damaging parts due to connection mistake),
• integrated sockets (ZIF + SOIC) with auto adaptive I/O pins reduces requirement of additional adapters,
• short programming time2, e.g. WINBOND W25Q80BV (8Mb): read 0.9s (8,4Mb/s), write 3.3s (2,4Mb/s), MICRON N25Q128A (128Mb): read
12.8s (10Mb/s), write 37.6s (3,4Mb/s),
• useful tools such as: save/load patterns with changes, i2c/spi custom scripts, auto backups, file comparing etc.
2
Due to USB 2.0 hardware layer (BULK mode) maximum real transfer is up to 10Mbit/s for read/write operations but in many cases transfer is limited by read/write time cycle from/to
memory (e.g. write is always slower than read). Write time does not include chip erase time (you can find tCE in device datasheet) and verification (read) time. There is possibility to change
write sequence (e.g. without erasing and verifying) but most devices require at least chip erase before write operation.
-7-
3. Installation of software and USB drivers
Requirements:
PC application is compatible with MS Windows3 XP, Vista, 7 , 8 and 10 (32 and 64-bit versions). You will need also .NET Framework 4.0 to run
application (probably already installed4 in your OS)
Software installation:
Software installation is typical for Windows. Just run setup (REVELPROG-IS_v1-x_Setup) and follow instructions (next, next, finish;). You may be
prompted for USB driver installation (accept it). Shortcut to REVELPROG-IS app will be added to the desktop. Application is ready to run.
Drivers installation:
In most cases drivers will be successful installed during application installation. Drivers may be installed also later from application (menu "help" ->
"install drivers").
Windows XP users will have to install drivers after first device plugged-in - just select drivers location in installation folder (by default it is
"C:\Program Files\REVELTRONICS\REVELPROG-IS\drivers\REVELPROG-IS"). If you miss it, you can install drivers later manually (run device manager,
find "REVLPROG-IS" device on the list, right click and update driver, select driver location).
Windows 8/10 x64 users will have to install drivers from REVELPROG-IS application by using "Zadig" installer (menu "help" -> "install drivers with
Zadig"). You should select REVELPROG-IS device on the list and install WinUSB driver, video: https://www.youtube.com/watch?v=6AFD3yBsRNc
3
Windows XP with SP3 installed (service pack 3). Windows 7 with SP1 installed.
In case of "fresh" install of OS you may need also "Microsoft Visual C++ 2010 Redistributable Package" (http://www.microsoft.com/en-us/download/details.aspx?id=5555)
4
if NOT, you can download and install it directly from Microsoft web page: http://www.microsoft.com/en-us/download/details.aspx?id=17718
-8-
4. First steps with REVELPROG-IS application
4.1. User interface
Application interface is user-friendly. All main functions can be run directly from shortcut icons (all icons are actived after device connected). Please
move cursor above specific icon to see additional tooltip.
-9-
Memory buffer is displayed in hexadecimal + ASCII format. There is possibility to edit buffer as bytes and as ASCII characters.
Additional information is displayed in lower area:
• buffer information: buffer size in bytes,
buffer addresses range and current
address (or addresses range) of cursor
position (selection) with calculated
checksum-16 (from selected bytes),
• status bar (programmer version info or
last operation info),
• CRC-32 checksum calculated from buffer
or opened file (click on "CRC32" to
recalculate checksum)
- 10 -
4.2. Device programming
Device type should be selected from the device database before any operation ("chip select" icon). Voltage will be set automatically. It can be
changed manually by clicking VPP icon. In case of ICSP programming with external power supply, VPP should be set to the same level as memory
power supply.
4.2.1. Reading
Before device reading operation, memory type should be
chosen. Please check also VPP voltage (you may need to
change it in case of low-voltage chips). Click READ icon
(memory chip with green arrow).
Programmer will read device. Memory content will be loaded
into the buffer. Buffer can be saved to external file. You can
also edit the buffer and reprogram the device.
Please note at the CRC32 checksum (right corner at the
bottom). If checksum is equal after each read than the risk of
read with error usually does not exist. It is a good practice to
make memory backup to external file before any writing.
The reading may be incorrect due to communication error or
broken chip.
- 11 -
4.2.2. Writing
Before device programming operation, (1) memory type should be chosen and (2) buffer should be filled with data. You can load data from external
binary (*bin, *.rom, *.epp etc.) or Intel-Hex (*.hex) file. Please check also VPP voltage – it may be changed in case of low-voltage chips. Please click
“WRITE” icon (memory chip with red-orange floppy disk).
Programmer will erase the device, write data to memory from
the buffer and make verification process. There is possibility to
change writing sequence from menu: Settings -> Write
sequence. Verification process will read the device after writing
and compare reading with the buffer. If verification pass than
memory is successful programmer. Verification error may occur
due to communication error, secured or broken chip.
4.2.3. Erasing
To erase memory, empty buffer can be loaded and
programmed into a memory. In most cases this operation is not
necessary, because programmer supports fast erase procedures
(Page Erase, Block Erase and Chip Erase). Please click “ERASE”
icon (memory chip with 0xFF and broom) for erasing operation.
Please note that erasing progress is not displayed at progress
bar. For high density FLASH memories erase process may took
quite long (even few minutes!).
- 12 -
4.3. HEX editor features (buffer editing)
4.3.1. HEX editor
Buffer can be edited from application level. In
the first column there is current address
displayed. In the second column there is memory
contents displayed (as bytes in hexadecimal
mode). In the third column there is ASCII
representation of memory contents. All buffer
operations are allowed (e.g. CTRL+C, CTRL+V
etc.). Modified buffer can be saved to external
.bin or .hex file.
4.3.2. Appearance
There is possibility to personalize hex editor,
e.g. color and font changes. Bigger font and dark
contrast colors will enhance your work with editor
especially on high resolution displays.
- 13 -
4.3.3. Fill buffer...
Fill selected bytes with constant bytes or defined pattern.
1. Open context menu (right click) and choose fill... 3. Take profit - you have just saved some time...
2. Enter pattern...
- 14 -
4.3.4. Patterns - export changes to file
All manual changes (highlighted bytes) can be exported to external file (pattern). Later, at any moment there is possibility to load pattern file and all
changes will be imported, without modifying other bytes in the buffer. Simple, fast and powerful.
4.3.5. Swap bytes
Swap bytes operation will change byte order in 2-bytes word. For example, swapped word 0xABCD will be equal to 0xCDAB. This functionality is very
useful for memories with two addressing modes, e.g. for microwire 93… series 16-bit chips. REVELPROG supports both addressing modes (8-bit and 16-
bit) for these devices.
- 15 -
4.3.6. Clear buffer or generate random buffer
There is possibility to clear buffer (0xFF) or generate random buffer from Edit menu. Buffer length will be equal to memory size. CTRL + N shortcut
will clear buffer and CTRL + N shortcut will generate random buffer.
4.3.7. CRC32 and Checksum-16
Click "CRC32" in right-bottom corner to calculate CRC32 checksum from the buffer. Changing single byte in the buffer will change CRC32 checksum
so this feature is useful in comparison of sequential reads or files. Checksum-16 is calculated in real time from selected bytes in the buffer area and it's
displayed in buffer info. This is most common algorithm for checksum used in wide range of devices (checksum of mileage, operation hours, serial
numbers etc.) To calculate Checksum-16 from all addresses select all bytes in the buffer area (CTRL+A).
4.3.8. File format conversion: .bin <-> .hex
I Application can be used also as a simple file converter (binary to intel-hex and vice versa). To convert file from one type to another, just open file
(load to buffer) and save it in another format.
- 16 -
4.3.9. DiffChecker (file comparing)
DiffChecker tool allows to compare 2 bin or hex files. All differences will be selected and grouped. Press F3/F2 to find next/previous difference region.
You can save all differences to external file as a pattern (feature described in Chapter 4.3.4). If files are totally different then first 1000 different
regions are marked.
- 17 -
4.4. Additional features
4.4.1. Blank test
Blank test checks if chip is empty. Test will be canceled as soon as first programmed cells will be detected (there is no need to read full memory).
4.4.2. Compare with the buffer
Operation compares buffer with the contents of memory. Operation will be cancelled as soon as first difference will be detected.
4.4.3. VPP selection
VPP is set for both: programming voltage and signal levels. VPP can be changed with 0.1V step in range of 1.0 - 5.0 volts. This feature is very useful
in few cases:
• in order to program low-voltage variant of the device (e.g. 1.8V instead of 3.3V),
• in case of in-circuit programming with external power supply -> programmer voltage should be the same as external circuit voltage or VPP
should disabled (VPP OFF),
• in case of in-circuit programming without external power supply. In many cases there is no need to set nominal voltage for external board. For
example: memory operates in range of 2.6 to 3.6 volts. Nominal voltage for external board is 3.3V. Setting the lowest operational voltage (2.6V)
will be enough to power and communicate with the memory and at the same time will be too low to power all circuits around. First of all, if there
is main microprocessor on the board than it will not communicate with the external memory (because it will be in "reset" state due to low
voltage to operate) so it will be possible to communicate with this memory using external programmer. Secondly, you will save current
consumption because devices in reset state consume much less power. This trick is not always possible, so if you can't communicate with the
device in external circuit try to plug-in external power supply or unsolder the chip and program it in socket. Please read Chapter 5 for more
details.
- 18 -
4.4.4. Device identification (Chip ID) for FLASH SPI, DATAFLASH and 1-wire devices
In order to read Chip ID please select “Tools” -> “Read ID” (F10). Operator should know operating voltage for the device because REVELPROG-IS
supports also low voltage chips and reading chip ID without knowledge about chip power supply level is risky (setting 3,3V for 1,8V chip will damage it
even during chip id reading). For FLASH devices programmer will read 4 identification bytes of data (JEDEC ID)– 1st byte is Manufacturer ID, 2nd and 3rd
bytes are Device ID and 4th byte is Extended ID. For some FLASH SPI devices programmer can auto select recognized chip from memory database. You
can read about identification bytes in device datasheet. For 1-wire devices programmer will read 64-bit unique identification number.
4.4.5. Quad SPI (QSPI) configuration for FLASH SPI
Some of FLASH SPI devices may require to enable QSPI mode before soldering it in external device. This will require to change one of configuration
or status registers in device memory map.
TIP: in most cases, specially when you reprogram FLASH SPI there is not necessary to change any configuration bits.
To enable or disable Quad mode you can use dedicated tool (Tools -> Quad SPI) – it will work with most popular FLASH SPI devices (e.g. Winbond
and Spansion). For other devices it may be necessary to write custom script (with Custom Script tool – described in Chapter 6) to enable or disable
QSPI mode manually by changing QSPI bits in required registers. You can read how to change Quad SPI mode for your device in device datasheet.
4.4.6. SFP/QSFP/XFP Transceivers support
REVELPROG-IS has dedicated tools for optical transceiver support. There is SFP/QSFP/XFP adapter required with external power supply. MSA
Standard is supported (e.g. SFF-8472, SFF-8636, INF-8077i). Dedicated functions allows to enter manufacturer/host password and program write
protected transceivers, brute force password (searching password for protected transceivers with unknown password), change manufacturer info,
model, serial number etc. and recalculate checksums directly from REVELPROG-IS application. Please check Chapter 7 for more details.
4.4.7. Auto backup
Every read operation there is backup file (.bin) generated (by default it is user documents folder in system). By default maximum 16 files are
created (oldest are deleted) and size is limited to 8Mbit devices. You can change these parameters in Settings -> Option -> File -> Autobackup (you
can set unlimited number of files and size).
- 19 -
5. In-Circuit Serial Programming (ICSP)
Caution! Before ICSP programming please read following instructions!
ICSP programming is recommended only for advanced users. There is required technical knowledge and being familiar with specific chip. You should
read carefully device datasheet, especially memory pinout, addressing modes and voltage levels.
Programmer is equipped with 10-pin ICSP socket (IDC10). There’s only 8 pins used (pin-9 and pin-10 are not internally connected). Pinout
numeration (1-8) is the same as memory pinout in datasheet for DIL8/SO8 package.
There will be various signals at these pins during chip programming (digital and analog signals). These signals are assigned automatically after
memory chosen (in application) and are set only during memory operation.
5.1. Addressing in external circuit
All hardware addressing outputs for EEPROM 24.. series (pin 1,2,3 ie A0, A1, A2) must have low voltage level (GND). If chip in circuit is addressed in
other way (e.g. there are few the same chips, which require various addressing) then communication will fail. In this case you can (1) set correct
addressing in application (“External addressing” option during memory selection) or (2) set default “0” addressing with the programmer (connect
addressing wires to the chip and in the same time disconnect them in external circuit) .The safest option is to unsolder the chip and put it to integrated
programmer socket.
Addressing 8/16-bit for EEPROM 93 series also needs special care. In circuit addressing wire (pin 6) can be connected to low or high state (it's
defining addressing mode if memory support both modes). Depends on your chip selection in application (8/16 bit) programmer gives LOW or HIGH
state on this pin. If you choose wrong addressing (e.g. in circuit it is low state and programmer outputs high state) than you will make short circuit. In
most cases it's not necessary to connect addressing wire (pin 6) for microwire 93 series - it's enough to select right mode from application (16-bit in
most cases).
If you are not 100% sure about connections, DO NOT program in circuit – unsolder the chip and program it with integrated socket.
- 20 -
5.2. Write protection in circuit (WP/PRE pin)
A lot of serial devices have WP (Write Protect) or PRE (Protection Enable) input. Low state on this pin (ground) protect the device from erasing and
writing. Programmer outputs a high state during erase or write operation. If in external circuit write protect pin is connected to ground (common case),
and programmer will output high state on this pin, than it will lead to short circuit. There are 3 common solutions in this case: (1) do not connect write
protect pin (erase/write will not work), (2) disconnect write protect pin in circuit (connect it only to programmer) or (3) unsolder the chip and
programm it in programmer's socket.
WP (Write-Protect) or PRE (Protection Enable) pin can be found e.g. in FLASH SPI 25.. (pin 3), FLASH SPI 26... (pin 3), FLASH SPI 45... (pin 5),
EEPROM I2C 24... (pin 7), EEPROM SPI 25.. (pin 3), EEPROM SPI 35... (pin 3), EEPROM SPI 95... (pin 3), EEPROM MICROWIRE 93... (pin 7).
5.3. Power supply in external circuit
The target application device can be either powered by programmer [voltage level (VPP) can be chosen from: 1.0V – 5.0V - please read Chapter
4.4.3] or powered by an application within a voltage range of 1.0V to 5.5V. If chip is already powered in external circuit, than VPP should be set to the
same voltage as external power supply (0,1V accuracy is tolerated). Absolute maximum rating at programmer's I/O pins is 5.5V - exceed this value
may damage protection buffers in programmer.
- 21 -
5.4. Limits and possible issues during in-circuit programming
In some cases there is no possibility to program chip in application. This can be due by many reasons, such as:,
• to long signal wires,
• too much load capacity in circuit,
• incorrect pull-ups or pull-downs on signal wires,
• incorrect addressing,
• bus conflict (memory is during communication with other device),
• impedance not match,
• additional capacitors, diodes bus-switches etc. in circuit.
In case of power supply from programmer, current is limited to 100mA for
safety reason. If application requires more power, than external power
supply should be connected.
In case of incorrect connections, short circuit or overload, following error
(pict.) will be displayed and all I/O will be disconnected. Delay of protection
trigger is 5-35ms so you still have to be careful. Programmer implements
"VPP-boost" mode which allows for 3x higher current consumption at the
first 30ms of operation (e.g. for capacitor charging). There is also possibility
to increase in settings overload protection to 200mA.
If you are not sure about connections or voltage levels DO NOT
program in-circuit. It is much safer to unsolder the chip and
program it in the socket.
- 22 -
5.5. SOIC Clip
Devices in SOIC package can be connected with SOIC CLIP (e.g. POMONA 5250 for SOIC-8 and POMONA 5252 for SOIC-16). Programming with a clip
is recommended only for advanced users (many traps for young players). Clip is a precision measuring device - before connecting the clip please
read chapters 5.1 – 5.4. Please follow tips below to avoid any accidental
damage to the clip:
• clip should be used only with SMD chips with SO-8 package (150mil
or 200mil),
• clip should NOT be used with physically damaged chips (not straight
pins or excess of tin),
• do NOT touch contact pins – any attempt of mechanical interference
will damage contact pins,
• it is NOT recommended to use the clip when device was previously
soldered in not professional way (pins may not contact to memory
pads; there is also risk of damage to the contact elements). In such
case it is recommend to use external adapter SOIC-8 150mil or
SOIC-8 200mil,
• it is NOT recommended to use the clip on a desoldered device (“in air”) – read and write may be incorrect (specially for fast devices, e.g. FLASH
SPI). All devices should be programmed in external circuit or in adapter, because only this method guarantees proper operations (in external
circuit there are additional filtering elements while external adapter guarantees the shortest connections). If you really need to connect
desoldered device in the clip, please do it very carefully. For FLASH SPI you should use as short wires as possible (5cm) and decrease SCK
frequency to 10% (Settings -> Options -> Hardware -> SCK = 10%). It not guarantees success but increases your chances.
- 23 -
Connecting the CLIP
Connection schema is displayed in application during device selection. In most cases connection is straight „1 to 1” as you can see on the left picture
(programmer pin 1 should be connected to memory pin 1, programmer pin 2 to memory pin 2, pin 3 to pin 3 etc.). In some cases connection is not
straight, e.g. for 35080 memory (programmer pin 1 to memory pin 2, programmer pin 2 to memory pin 4 etc. - picture on the right).
Straight connection „1 to 1” for FLASH SPI Not straight connection for 35080
First of all you should identify PIN 1 in the device 5. Secondly you should connect wires to the clip and then clamp the clip on the device (so
connections will fit to schema). It is recommended to use dedicated ISP 10-pin socket in programmer. Please do not suggest with color of wires in tape
– only pin numbers are important. Example movie with POMONA CLIP connecting for 1-wire device: https://youtu.be/r2T78o7oxfQ?t=145
5
Pin no. 1 in the device is pointed with small dot in corner or with milled edge (as you can see at picture in schema above)
- 24 -
5.6. Troubleshooting for in-circuit programming
If you can program device in programmer's socket (or adapter) with success, but you cannot program it in circuit than there are few things that you
can check. First of all, make sure that:
• all wires are connected properly (please take special care for pin contact in case of programming with SOIC CLIP),
• external circuit is powered properly and there is no voltage conflict on power bus,
• SPI lines: CS, (MOSI), (MISO) and (SCK) have pull-up resistors to power supply (4.7k - 10k),
• communication lines do not have additional elements, such as diodes, bus-switches, transistors etc.
• there is no communication conflict on the bus (e.g. processor and all other devices connected to shared SPI bus should be in RESET state).
Secondly, if problem still exist, there are still may be some tricky issues. Few examples with solutions below:
• noise and overshooting (communication errors, random read) – possible solutions:
o decrease SPI clock to 10% for FLASH SPI devices (menu Settings -> Options -> Hardware -> FLASH SPI SCK),
o impedance matching and termination for external circuit (and wires) by using e.g. termination resistors on signal wires. There is no universal
value of resistance (each circuit is different) but in most cases 100 - 1000 Ohm resistors in serial for CS, (MOSI) and (SCK) will be enough:
o CS line decoupling (33pF - 220pF to ground as close as possible to the device in-circuit),
• to low voltage level during erasing and/or writing (erase error / communication error):
- 25 -
o when external device (in external circuit) is powered from programmer, than there are also other devices powered too (on the same
power line) and due to higher current consumption output voltage may be too low for erase and write operations. In this case it is
recommended to set VPP slightly higher (e.g. +0.3V) or use external power source and set the same VPP level in application.
• bus conflict (random read or communication error during read):
o in some cases after device power up, the main processor is starting communication with slave devices (e.g. with memory you are trying
to read) – in this case it will be conflict on the bus (random read or communication error). All devices connected to the same
communication bus should be forced to be in RESET state. Sometimes it is enough to use external power supply and wait about 2-3
minutes for initial procedure finished and then try to communicate with the memory (when all devices are in idle state and bus is free).
The other tricky way is to use minimum voltage level to communicate with memory and this voltage level may be too low for oth er
devices so they will stay in RESET state and will not interrupt communication. On the other hand, to low voltage level may be not enough
to success for erase and write operations.
In some cases design of external circuit does not physically allow for in-circuit programming. In this case chip should be unsoldered and programmed in
programmer's socket or adapter.
- 26 -
6. Custom Script Programming (I2C / SPI / 1-wire bus)
Custom script programming for I2C/SPI/1-wire bus in case of REVELPROG is a some kind of "bus pirate" tool for serial communication. This tool is still
in developement phase but it is already powerful and functional. With REVELPROG-IS Customs Script tool there is possibility to execute any
commands in any sequence with precise delays on SPI, I2C or 1-wire bus. You can write script to execute commands for unclocking device,
read and write hidden (or not) registers, change sector protection bits, write OTP registers and much more.
In practice it is also very useful tool for electronic enginners and embedded programmers, because there is possibility to communicate with any
serial (I2C, SPI and 1-wire) device. External device or module can be also powered from REVELPROG-IS (1.0 - 5.0V with 0.1V threshold). Only few
connection lines are required for communication (4 wires for SPI or 2 wires for I2C + optional 2 wires for external device power supply).
6.1. Script construction
Typical script consists of (1) #SCRIPT HEADER - information about
software version, (2) #HARDWARE SETTINGS - voltage selection (VPP),
bus selection (I2C/SPI) and communication speed, (3) #OPERATION (1
to n). Each script has to have at least one operation defined.
Each #OPERATION consists of (1) ‘SW’ operation parameters: number
of bytes to read/write, delay settings, (2) ‘INSTR’ instruction - sequence
of bytes for single instruction, (3) ‘DATA’ data to write (optional) -
sequence of optional bytes for write after single instruction
Example construction of typical script with header (software version
v.1.6.0), hardware settings (SPI bus, 3.3V voltage, slowest speed) and
single operation with 1-byte 9Fh command is presented on right image:
- 27 -
6.2. Script syntax
• "#" defines sections, e.g. #SCRIPT HEADER; (header), #HARDWARE SETTINGS; (hardware settings), #OPERATION; (for each operation),
• ";" is placed at the end of each command,
• ":" is placed directly after command words, e.g. SCRIPT: (script version), HW: (hardware settings), SW: (software settings - operation
parameters), INSTR: (instruction), DATA: (write data);
• "," separates parameters for each command (e.g. between "INSTR:" and ";" comma separates instruction bytes)
• "//" precedes comments which are ignored by script executor
Each script should have single #SCRIPT HEADER, single #HARDWARE SETTINGS and at least one #OPERATION (or more).
6.3. Script maker with GUI
Script maker will help you prepare multiple operations with correct syntax. You
need to set few parameters for each operation:
• WREN (Write Enable) + number of bytes to write in single operation,
• RDEN (Read Enable) + number of bytes to read in single operation,
• DBO (Delay Before Operation) - optional delay in ms before operation,
• DAI (Delay After Instruction) - optional delay in ms after instruction,
• DAW (Delay After Write) - optional delay in ms after write,
• DAO (Delay After Operation) - optional delay in ms after operation,
• BSYO (Busy Operation) - maximum time in ms for write end (e.g.
maximum wait time for busy flag in FLASH SPI or for ACK in I2C devices)
• TOUT (Timeout) - maximum PC timeout in ms for operation end (it is recommended to set timeout greater than sum of all other delays).
Please note that:
• Read/Write length are 0 based (0 means 1 byte, 255 means 256 bytes) and with WREN=0/RDEN=0 length parameter is ignored,
• "SW:" and "HW:" byte format is decimal,
- 28 -
• "INSTR:" and "DATA:" byte format is hexadecimal.
Operation code generated by script maker from above example::
#OPERATION;
SW:0,0,1,3,5,5,10,0,100,1000;
INSTR:9F;
As you can see SW parameters are equal to script maker parameters:
SW:WREN[0-1],WriteLength[0-255],RDEN[0-1],ReadLength[0-255],DBO[0-250],DAI[0-250],DAW[0-250],DAO[0-250],BSYO[0-n],TOUT[0-n];
6.4. Script execution sequence
Each script is executed with following sequence:
1. SET HW (BUS, VPP, SPEED)
2. EXECUTE OPERATION 1 (SET SW -> DBO -> INSTR -> DAI -> WRITE -> DAW -> BSYO -> READ -> DAO)
3. EXECUTE OPERATION 2
4. ...
5. EXECUTE OPERATION N
6. RESET HARDWARE
6.5. Script examples
Please take a look at forum tutorial for more information and script examples:
https://forum.reveltronics.com/viewtopic.php?f=22&t=280
- 29 -
7. SFP / QSFP / XFP transceivers
REVELPROG-IS allows programming SFP, QSFP and XFP transceivers. Hardware adapter with SFP/QSFP/XFP connectors and external power supply is
required. MSA Standard is supported (e.g. SFF-8472, SFF-8636, INF-8077i). Special features allows to enter manufacturer / host password and
program write protected transceivers, brute force password (searching password for protected transceivers with unknown password), change
manufacturer info, model, serial number etc. and recalculate checksums directly from REVELPROG-IS application.
7.1. Adapter connection
Please connect external QSFP SFP XFP Adapter for REVELPROG-IS using
10-pin connector. Please connect power supply to adapter. Please insert
transceiver to dedicated transceiver slot. Only one transceiver should be
inserted at the same time.
Example of connected QSFP SFP XFP Adapter (please note that power supply
of adapter is also from PC USB port):
- 30 -
7.2. Device selection and memory map
Please select transceiver type from memory database (EEPROM -> Transceivers -> SFP or QSFP or XFP).
7.2.1. SFP and SFP+
• SFP [A0] and SFP [A2] allows to read/erase/write/verify of A0h and A2h blocks of SFP Transceivers.
These blocks may contain also diagnostic or write protected sectors, so verify may not pass for protected sectors.
• SFP [USER] allows read/erase/write of any block or page
in memory map (verification should be done by user). The
[USER] mode allows to read/write specific part of memory.
In block A0h (256bytes) first 128bytes (00h – 7Fh) are for
serial ID and vendor information. It may be write protected
(password may be required). Second 128bytes (80h-FFh)
are reserved.
In block A2h (256bytes) first 127bytes (00h – 7Eh) are
diagnostic information (alarm and warning thresholds, cal
constants, real time diagnostics) and optional password
entry area. 128th byte (7Fh) is page select byte (only if SFP
supports pages). Next 128 bytes (80h-FFh) is page content
(depends on selected page). SFP may not support A2h block
(it will be communication error) or page select (it may
contain only single page). Page 00h or 01h is User Writable
EEPROM (120bytes) and vendor specific (8bytes). Page 0
may be write protected (password may be required). Page
02h is for control functions. Pages 03h-7Fh are reserved.
Pages 80h-FFh are vendor specific.
- 31 -
7.2.2. QSFP and QSFP+
• QSFP [USER] allows to read/erase/write of any block or page in QSFP/QSFP+ memory map (verification should be done by user). The [USER]
mode allows to read/write specific part of memory.
QSFP/QSFP+ contains only block A0h (256 bytes) divided into pages (byte
7Fh in block A0h is page select byte). Pages are 128bytes length. Page 00h
is required and provides static module identity and capabilities information
(it may be write protected with password). Other pages may be optional.
Please check memory map for your QSFP/QSFP+ or in MSA Standard (SFF-
8636 specification).
With REVELPROG-IS you can select page from menu (you do not have to
change page bytes manually in buffer) and read/write specific pages:
- 32 -
7.2.3. XFP
• XFP [USER] allows to read/erase/write of any block or table in QSFP/QSFP+
memory map (verification should be done by user). The [USER] mode allows to
read/write specific part of memory.
XFP contains only block A0h (256 bytes) divided into tables (byte 7Fh in block
A0h is table select byte). Tables are 128bytes length. Table 01h is default and
contains Serial ID Data. Table 02h is User EEPROM. Tables may be write
protected (password may be required for erase or write). Other pages may be
optional.
Please check memory map for your XFP or in MSA Standard (INF-8077i
specification).
With REVELPROG-IS you can select table from menu (you do not have to
change page bytes manually in buffer) and read/write specific tables.
7.3. Protected transceivers: manufacturer password and host password
Some transceivers also provides an optional password entry location that may be used to protect vendor internal function or user writable memory.
Password shall not be required to read any data, but it may be used for write protection for specific areas. Nor shall passwords be required to write any
controls defined in the digital diagnostics functions. Passwords may be used by vendors to control write access to MSA defined read only data for
factory setup, or to OEMs to limit write access in the User EEPROM area. Finally, passwords may be used to control read or write access to the vendor
specific pages or tables. Separate passwords value ranges will be defined to prevent accidental writing to critical module control areas. There are 2
types of passwords: manufacturer password and host password (also known as user password). You can enter password using password tool in
REVEPLROG-IS application.
- 33 -
7.3.1. Host/User password
Host password is protecting User Writable EEPROM. Entering valid user password will unlock only user eeprom for erase and write operations.
Location of this area depends on transceiver type (please check memory map for your transceiver). In most cases user can change this password (if
current password is known). All factory new transceivers should have default host password: 00h 00h 10h 11h.
7.3.2. Manufacturer password
Manufacturer password is protecting whole memory map, e.g. serial number, product name,
manufacturer name, vendor specific areas etc. Entering valid manufacturer password will unlock all
memory map for erase and write operations. Only manufacturer know this password, but
REVELPROG-IS provides tool for searching password with brute force method.
7.3.3. Hacking password (brute-force method)
REVELPROG-IS password tool for transceivers can be also used to search password using brute
force method (checking all combinations or limited range of combinations). It uses smart algorithm
with auto-adjusting communication speed and delays to check as many password as possible in
shortest time. For fastest MCU based transceivers it’s possible to check 4000 password combinations
per second. Please check more details and on REVELTRONICS forum:
https://forum.reveltronics.com/viewtopic.php?f=31&t=527
- 34 -
8. Updates
New trends on the market and latest devices require from users newer and newer programming devices. Customer's satisfaction is our number one
priority and we share updates free of charge for all users of REVELPROG-IS. Update consist of software update (pc application) and firmware update
(software inside the device). Latest software can be downloaded directly from manufacturer’s webpage. You will be informed by the software about
possible updates after connecting out of date device.
Caution! If a firmware update process is interrupted, your programmer may not function properly. Updates are optional – warranty does not cover
damage due improper care.
During update process, device will start in DFU (Device Firmware Upgrade) mode. First time it may be necessary to install add itional drivers (for DFU
mode). Windows should find drivers automatically on the Internet (if not, there are also available in /drivers/DFU subdirectory in the installation folder).
Installing drivers process should take about 30 seconds. If DFU drivers are installed, application will update the firmware device. Appropriate
instructions will be displayed before.
Please close all other applications and disable antivirus software during update
process. Do not disconnect and do not connect any USB devices during update
process. Make sure that you have stable power supply for PC.
Update process may take about half a minute. Progress will be displayed on the
screen. There is no possibility to cancel this process! After successful update,
device will restart and will be ready to use.
- 35 -
9. Research and development
We are keen to still develop and improve the device. Please contact us at [email protected] or visit our contact page at www.reveltronics.com if
you have any comments or tips about REVELPROG-IS.
Very welcome are ideas:
• how to improve REVELPROG-IS - what functionality add to it,
• what chips add to supported device list in the next update (please suggest only serial I2C, SPI, uWire devices).
Repeated suggestions from many users will have more chance for implementation in the future. We encourage you to contact us because in this way
we already added many devices popular only in small segments of automotive market, computer service, RTV/AGD devices etc.
- 36 -
10. APPENDIX A - List of supported devices
The following list details the family of supported devices (left column) with selected examples of supported memories (right column). Most chips
have the same programming procedures – programmer supports more devices than the examples given in the list.
9.1. EEPROM I2C 24… series
24AA01 | 24AA014 | 24AA014H | 24AA01H | 24C01 | 24C01A | 24C01B | 24C01C | 24LC01 | 24LC014 | 24LC014H | 24LC01B | 24LC01BH | AF24BC01 | AT24C01 |
AT24C01A | AT24C01B | BR24A01AF | BR24A01AFJ | BR24C01 | BR24C01A | BR24C01AF | BR24C01AFJ | BR24C01AFV | BR24C21F | BR24C21FJ | BR24C21FV | BR24G01 |
24..01 BR24G01F | BR24G01FJ | BR24G01FV | BR24G01FVT | BR24L01 | BR24L01A | BR24L01AF | BR24L01AFJ | BR24L01AFV | BR24L01AFVM | BR24L01AFVT | BR24T01A |
(1kb) CAT24AA01 | CAT24C01 | CAT24C01B | CAT24C21 | CAT24FC01 | CAT24LC01 | CAT24WC01 | CR24C01 | CY24C01 | FM24C01 | FT24C01 | FT24C01A | GE24C01 | GP24BC01
| HM24LC01 | HT24C01 | HT24LC01 | IS24C01 | IS24C01B | LT24C01 | LX24C01 | M24C01 | MM24C01 | S-24C01A | S-24C01B | S-24C01C | S-24CS01A | SLA24C01 |
SLE24C01 | ST24C01 | ST24W01 | TMC24A01 | TU24C01B | UG24C01 | X24012 | X24C01 | X24C01A | XL24C01A
24AA02 | 24AA024 | 24AA024H | 24AA025 | 24AA02H | 24C02 | 24C02A | 24C02B | 24C02C | 24LC02 | 24LC024 | 24LC024H | 24LC025 | 24LC02B | 24LC02BH | 24LC02W |
24LLC02 | A24C02 | ACE24C02 | ACE24LC02 | AF24BC02 | AM24LC02 | AT24C02 | AT24C02A | AT24C02B | AT24C02C | AT24HC02B | AT24HC04B | AX24C02A | BJX25LC02
| BL24C02 | BR24A02F | BR24A02FJ | BR24A02FVM | BR24C02 | BR24C02F | BR24C02FV | BR24G02F | BR24G02FJ | BR24G02FVT | BR24L02 | BR24L02F | BR24L02FJ |
BR24L02FV | BR24L02FVM | BR24L02FVT | BR24T02 | CAT24AA02 | CAT24C02 | CAT24C03 | CAT24LC02 | CAT24LC02A | CAT24LC02AZ | CAT24LC02Z | CAT24WC02 |
24..02 CAT24WC03 | CKD24A02 | CR24C02 | CW24C02 | CW24C02B | CY24C02 | EC24C02 | EC24C02A | EM24LC02 | FM24C02 | FM24C02U | FM24C02UF | FM24C03U |
(2kb) FM24C03UF | FT24C02 | FT24C02A | GE24C02 | GM24LC02B | GP24BC02 | HM24LC02 | HN58X2402 | HT24C02 | HT24LC02 | IN24AA02A | IN24AA02B | IN24LC02B |
IS24C02 | IS24C02A | IS24C02B | IS24C02E | K24C02 | KK24LC02B | L24C02 | L24W02 | LE24C0221 | LE24C023 | LE24L0221 | LT24C02 | LX24C02 | LY24C02 | M24C02 |
MAX24A02 | MC24C02 | MC24LC02 | MM24C02 | NM24C02 | NM24C02F | NM24C02U | NM24C03 | NM24C03F | NM24W02 | NSC24C02 | PCF8582C-2 | PTK24A02T | RT24A02
| S-24C02A | S-24C02B | S-24C02C | S-24CS02A | SLA24C02 | SLE24C02 | SM24C02 | ST24C02 | ST24W02 | T24C02 | T24C02A | TMC24A02 | TU24C02B | UG24C02 |
WS24C02 | X24022 | X24C02 | XL24C02 | Y24LC02
24AA04 | 24AA04H | 24C04 | 24C04A | 24LC04 | 24LC04B | 24LC04BH | A24C04 | ACE24C04 | ACE24LC02 | AF24BC04 | AM24LC04 | AT24C04 | AT24C04A | AT24C04B |
AX24C04A | BJX24LC04 | BL24C04 | BR24A04F | BR24A04FJ | BR24C04 | BR24C04F | BR24C04FJ | BR24C04FV | BR24G04F | BR24G04FJ | BR24G04FV | BR24G04FVT |
BR24L04 | BR24L04F | BR24L04FJ | BR24L04FV | BR24L04FVM | BR24L04FVT | BR24T04 | CAT24C04 | CAT24C05 | CAT24LC04 | CAT24WC04 | CAT24WC05 | CR24C04 |
24..04 CW24C04 | CW24C04A | CY24C04 | EC24C04 | EC24C04A | FM24C04 | FM24C04U | FM24C04UF | FM24C05U | FM24C05UF | FM24CL04 | FT24C04 | FT24C04A | GE24C04 |
(4kb) GM24LC04B | HM24LC04 | HN58X2404 | HT24C04 | HT24LC04 | IN24LC04B | IS24C04 | IS24C04A | IS24C04B | K24C04 | KK24LC04 | KK24LC04B | L24C04 | L24W04 |
LE24C042 | LE24C043 | LT24C04 | LX24C04 | LY24C04 | M24C04 | M24LC04 | MM24C04 | NM24C04 | NM24C04F | NM24C04U | NM24C05 | NM24C05F | NM24W04 | S-
24C04A | S-24C04B | S-24CS04A | SLA24C04 | SLE24C04 | ST24C04 | ST24W04 | T24C04 | T24C04A | TMC24A04 | TU24C04B | UG24C04 | WS24W04 | X24042 | X24C04 |
XL24C04 | Y24LC04
24..08 24AA08 | 24AA08H | 24C08 | 24C08B | 24LC08 | 24LC08B | 24LC08BH | 24LLC08 | A24C08 | ACE24C08 | ACE24C08A | ACE24LC08 | ACE24LC08A | AF24BC08 | AM24LC08 |
(8kb) AT24C08 | AT24C08A | AT24C08B | AT24RF08C | AX24C08A | BL24C08 | BR24A08F | BR24A08FJ | BR24C08 | BR24C08F | BR24C08FJ | BR24C08FV | BR24G08F |
- 37 -
BR24G08FJ | BR24G08FV | BR24G08FVT | BR24L08 | BR24L08F | BR24L08FJ | BR24L08FV | BR24L08FVM | BR24L08FVT | BR24T08 | CAT24C08 | CAT24LC08 | CAT24WC08 |
CR24C08 | CW24C08 | CW24C08B | CY24C08 | EC24C08 | EC24C08A | FM24C08 | FM24C08U | FM24C08UF | FM24C09UF | FM24CL08 | FT24C08 | FT24C08A | GM24LC08B |
GP24BC08 | HN58X2408 | HT24C08 | HT24LC08 | IN24AA08B | IN24LC08B | IS24C08 | IS24C08A | K24C08 | KK24LC08 | KK24LC08B | L24M08 | L24W08 | LE24C081 |
LE24C082 | LE24L082 | LT24C08 | LX24C08 | LY24C08 | M24C08 | MAX24A08 | MC24C08 | MC24LC08 | MM24C08 | MTV24C08 | MTV24LC08 | NM24C08 | NM24C08F |
NM24C08U | NM24C09 | NM24C09F | NM24C09U | NM24W08 | NSC24C08 | P24S08 | PCA24S08 | PS08 | PTK24A08T | S-24C08A | S-24C08C | S-24CS08A | SLA24C08 |
SLE24C08 | ST24C08 | ST24W08 | T24C08 | T24C08A | TMC24A08 | TU24C08B | UG24C08 | WS24W08 | X24C08 | XL24C08 | Y24LC08
24AA16 | 24AA16H | 24C16 | 24C16B | 24LC16 | 24LC164 | 24LC16B | 24LC16BH | 24LLC16 | 24U17 | A24C16 | ACE24C16 | ACE24LC16 | AF24BC16 | AM24LC16 | AT24C16
| AT24C164 | AT24C16A | AT24C16B | AT24C16C | AX24C16A | BJX24LC16 | BL24C16 | BR24A16F | BR24A16FJ | BR24C16 | BR24C16F | BR24C16FJ | BR24C16FV |
BR24E16 | BR24E16F | BR24E16FJ | BR24E16FV | BR24G16F | BR24G16FJ | BR24G16FV | BR24G16FVT | BR24L16 | BR24L16F | BR24L16FJ | BR24L16FV | BR24L16FVT |
BR24S16F | BR24S16FJ | BR24S16FV | BR24S16FVM | BR24S16FVT | BR24T16 | CAT24C16 | CAT24C16L | CAT24C16Z | CAT24FC16 | CAT24FC17 | CAT24WC16 |
24..16
CAT24WC17 | CR24C16 | CW24C16 | CW24C16A | CY24C16 | EC24C16 | EC24C16A | FM24C16 | FM24C16U | FM24C16UF | FM24C17 | FM24C17U | FM24C17UF | FM24CL16
(16kb)
| FT24C16 | FT24C16A | GM24LC16B | GP24BC16 | HM24LC16 | HN58X2416 | HT24C16 | HT24LC16 | IN24LC16B | IS24C16 | IS24C16A | KK24LC16 | KK24LC16B | L24W16
| LE24C162 | LE24L162 | LT24C16 | LX24C16 | LY24C16 | M24C16 | MAX24A16 | MC24C16 | MC24LC16 | MM24C16 | MTV24C16 | MTV24LC16 | NM24C16 | NM24C16F |
NM24C16U | NM24C17 | NM24C17F | NM24C17U | NM24W16 | NSC24C16 | PTK24A16T | S-24C16A | S-24CS16A | SLA24C16 | SLE24C16 | SLE24C164 | ST24C16 |
ST24W16 | T24C16 | T24C16A | TMC24A16 | TU24C16B | UG24C16 | WS24W16 | X24164 | X24165 | X24C16 | XL24C16 | XL24C164 | Y24LC16
24AA32 | 24AA32A | 24C32 | 24LC32 | 24LC32A | 24LC32B | A24C32 | ACE24C32 | ACE24C32A | AF24BC32 | AT24C32 | AT24C32A | AT24C32B | AT24C32C | AT24C32D |
AX24C32A | BR24A32F | BR24A32FJ | BR24C32 | BR24C32F | BR24G32F | BR24G32FJ | BR24G32FV | BR24G32FVT | BR24L32 | BR24L32F | BR24L32FJ | BR24L32FV |
24..32 BR24L32FVT | BR24S32F | BR24S32FJ | BR24S32FV | BR24S32FVM | BR24S32FVT | BR24T32 | CAT24C32 | CAT24FC32 | CAT24FC32A | CAT24WC32 | CAT24WC33 |
(32kb) CR24C32 | CW24C32 | EC24C32 | EC24C32A | FM24C32 | FM24C32U | FM24C32UF | FT24C32 | FT24C32A | HM24LC32 | HN58X2432 | HT24C32 | HT24LC32 | IN24AA32A |
IS24C32 | IS24C32A | IS24C32B | IS24C32C | K24C32 | L24W32 | LE24C322 | LE24L322 | M24C32 | MC24C32 | MM24C32 | NM24C32 | NM24C32U | NM24C32UF |
NSC24C32 | PTK24A32T | S-24C32C | SLA24C32 | SLE24C32 | ST24C32 | T24C32 | T24C32A | TU24C32 | WS24W32 | X24320
24AA64 | 24AA64F | 24AA65 | 24C64 | 24C65 | 24FC64 | 24LC64 | 24LC64B | 24LC64F | 24LC65 | A24C64 | ACE24C64 | ACE24C64A | AF24BC64 | AT24C64 | AT24C64A |
AT24C64B | AT24C64C | AT24C64D | AX24C64A | BR24A64F | BR24A64FJ | BR24C64 | BR24C64F | BR24G64F | BR24G64FJ | BR24G64FV | BR24G64FVT | BR24L64 |
24..64 BR24L64F | BR24L64FJ | BR24S64F | BR24S64FJ | BR24S64FV | BR24S64FVM | BR24S64FVT | BR24T64 | CAT24C64 | CAT24FC64 | CAT24FC65 | CAT24FC66 | CAT24WC64 |
(64kb) CAT24WC65 | CR24C64 | CW24C64 | EC24C64 | EC24C64A | FM24C64 | FM24C64F | FM24CL64 | FT24C64 | FT24C64A | HM24LC64 | HN58X2464 | HT24C64 | HT24LC64 |
IS24C64 | IS24C64A | IS24C64B | K24C64 | L24W64 | LE24CB642 | M24C64 | MM24C64 | NM24C65 | NM24C65F | NSC24C64 | PTK24A64T | S-24C64C | SLA24C64 |
SLE24C64 | ST24C64 | T24C64 | T24C64A | TU24C64B | WS24W64 | X24640 | X24641 | X24645
24AA128 | 24C128 | 24FC128 | 24LC128 | 24LC21 | 24LC21A | 24LCS21A | ACE24C128 | AF24BC128 | AT24C128 | AT24C128B | AT24C128C | AT24CS128 | AX24C128A |
24..128 BL24C128 | BR24G128F | BR24G128FJ | BR24G128FV | BR24G128FVT | BR24S128F | BR24S128FJ | BR24S128FV | BR24S128FVT | BR24T128 | CAT24C128 | CAT24WC128 |
(128kb) CAT24WC129 | CR24C128 | CW24C128 | EC24C128 | EC24C128A | FM24C128 | FM24C128F | FM24CL128 | FT24C128 | FT24C128A | HN58X24128 | HT24C128 | HT24LC128
| IS24C128 | IS24C128A | IS24C128B | IS24L128 | LE24CB1283 | M24128 | S-24C128C | T24C128 | T24C128A | TU24C128
24AA256 | 24C256 | 24FC256 | 24LC256 | A24C256 | ACE24C256 | AT24C256 | AT24C256B | AT24C256C | AT24CS256 | AX24C256A | BL24C256 | BR24S256F | BR24S256FJ
24..256
| BR24T256 | CAT24C256 | CAT24FC256 | CAT24WC256 | CAT24WC257 | CW24C256 | EC24C256A | FM24C256 | FM24C256F | FM24CL256 | FT24C256 | FT24C256A |
(256kb)
HN58X24256 | HT24C256 | HT24LC256 | IS24C256 | IS24C256A | IS24L256 | M24256 | MC24C256 | T24C256 | T24C256A | TU24C256
- 38 -
24..512 24AA512 | 24C512 | 24FC512 | 24LC512 | 24LC515 | AT24C512 | AT24C512B | AT24C512C | CAT24C512 | CAT24WC512 | FM24C512 | FM24CL512 | FT24C512A |
(512kb) HN58X24512 | HT24C512 | HT24LC512 | IS24C512 | M24512 | SA24C512
24..1024 24AA1024 | 24AA1025 | 24AA1026 | 24C1024 | 24C1025 | 24C1026 | 24FC1024 | 24LC1024 | 24LC1025 | 24LC1026 | AT24C1024 | AT24C1024B | CAT24C1024 |
(1Mb) CAT24WC1024 | FM24C1024 | FM24CL1024 | HT24C1024 | HT24LC1024 | IS24C1024 | M24M01
24..2048
M24M02
(2Mb)
9.2. EEPROM SPI 25… series
25..010 25010 | 25AA010 | 25AA010A | 25C010 | 25LC010 | 25LC010A | A25010A | AT25010 | BR25H010-W | BR25L010-W | CAT25C01 | CAT25C11 | CY25C01 | IS25C01 | S-
(1kb) 25A010A | ST25C01 | ST25W01 | XC25010
25..020 25020 | 25AA020 | 25AA020A | 25C020 | 25LC020 | 25LC020A | AT25020 | AT25020A | BR25H020-W | BR25L020-W | CAT25C02 | CAT25C03 | CY25C02 | FM25C020U |
(2kb) FM25C020UL | IS25C02 | NM25C020 | S-25A020A | ST25C02 | ST25W02 | X25020 | XC25020
25..040 25040 | 25AA040 | 25AA040A | 25C040 | 25C040A | 25LC040 | 25LC040A | AT25040 | AT25040ACAT25C04 | BR25H040-W | BR25L040-W | CAT25C05 | CY25C04 |
(4kb) FM25C040U | FM25C040UL | FM25C041U | FM25L04 | IN25AA040 | IS25C04 | NM24C040 | NM24C041 | S-25A040A | ST25C04 | ST25W04 | X25040 | X25041 | XC25040
25..080 25080 | 25AA080 | 25AA080A | 25AA080B | 25C080 | 25LC080 | 25LC080A | 25LC080B | AT25080 | AT25080A | AT25080B | BR25H080-W | BR25L080-W | CAT25C08 |
(8kb) CAT25C09 | CY25C08 | FM25L08 | IN25AA080 | IS25C08 | S-25A080A | ST25C08 | ST25W08 | X25080 | X25F008 | XC25080
25160 | 25AA160 | 25AA160A | 25AA160B | 25C160 | 25LC160 | 25LC160A | 25LC160B | AT25160 | AT25160A | AT25160B | BR25H160-W | BR25L160-W | CAT25C16 |
25..160
CAT25C17 | CY25C16 | FM25C160 | FM25C160U | FM25C160UL | FM25L016 | IN25AA160 | IS25C16 | NM24C160 | S-25A160A | ST25C16 | ST25W16 | X25160 | X25170 |
(16kb)
X25F016 | XC25160
25..320 25320 | 25AA320 | 25AA320A | 25C320 | 25LC320 | 25LC320A | AT25320 | AT25320A | AT25320B | BR25H320-W | BR25L320-W | CAT25C32 | CAT25C33 | FM25C320U |
(32kb) FM25C320UL | IS25C32 | IS25C32A | IS25C32B | S-25A320A | TI2532 | X25320 | X25F032 | XC25320
25..640 25640 | 25AA640 | 25C640 | 25LC640 | AT25640 | AT25640A | AT25640B | BR25L640-W | CAT25C64 | CAT25C65 | FM25C640U | FM25CL64 | FM25L64 | IS25C64 |
(64kb) IS25C64A | IS25C64B | NM24C640 | S-25A640A | TI2564 | X25640 | X25642 | X25650 | X25F064 | XC25640
25..128
25128 | 25AA128 | 25C128 | 25LC128 | AT25128 | AT25128A | CAT25C128 | IS25C128 | IS25C128A | S-25C128A | X25128 | X25138 | X25F128 | XC25128
(128kb)
25..256
25256 | 25AA256 | 25C256 | 25LC256 | AT25256 | AT25256A | CAT25C256 | FM25L256 | IS25C256 | IS25C256A | X25256 | XC25256
(256kb)
25..512
25512 | 25AA512 | 25C512 | 25LC512 | AT25512 | XC25512
(512kb)
25..1024
251024 | 25AA1024 | 25C1024 | 25LC1024 | AT251024 | XC251024
(1Mb)
- 39 -
9.3. EEPROM SPI 35… series
NOTE: Incremental register (first 32 bytes) can be written only with higher value.
35..080
D80D0WQ | D80DOWQ | M35080 | M35080-3 | M35080-6 | M35080V6 | M35080-VP
(8kb)
35..160
D160D0WQ | D160D0WT | D160DOWQ | D160DOWT | M35160
(16kb)
9.4. EEPROM SPI 90… series
(1kb - 4kb) BR9010 | BR9020 | BR9040
9.5. EEPROM SPI 95… series
(1kb - 2Mb) M95010 | M95020 | M95040 | 5P08 | 5P08C3 | M95080 | M95160 | M95320 | M95640 | M95128 | M95256 | M95512 | M95M01 | M95M02
9.6. EEPROM MICROWIRE 93… series
Supported both addressing (8-bit and 16-bit) modes.
93..06
9306 | 93C06 | KM93C06 | KM93C06GD | M93C06 | NMC9306 | NMC93C06L | NMC93C06LZ
(256b)
93AA46 | 93AA46A | 93AA46B | 93AA46C | 93C46 | 93C46A | 93C46B | 93C46C | 93CX46 | 93LC46 | 93LC46A | 93LC46B | 93LC46C | 93S46 | 93X46 | A93C46(x16) |
A93C46(x8) | AF93BC46(x16) | AF93BC46(x8) | AK93C46 | AM93LC46 | AT93C46(x16) | AT93C46(x8) | AT93C46A | AT93C46B | AT93C46C | AT93C46D(x16) | AT93C46D(x8)
| AT93C46E | BL93C46(x16) | BL93C46(x8) | BR93A46 | BR93C46 | BR93H76 | BR93L46 | BR93LC46 | CAT93C46(x16) | CAT93C46(x8) | CAT93C46A | CAT93C46AH |
CAT93C46B(x16) | CAT93C46B(x8) | CAT93C46H(x16) | CAT93C46H(x8) | CAT93C46R(x8) | CAT93HC46(x16) | CAT93HC46(x8) | CR93C46(x16) | CR93C46(x8) |
93..46 EC93C46A(x16) | EC93C46A(x8) | EM93LC46(x16) | EM93LC46(x8) | FM93C46 | FM93C46A(x16) | FM93C46A(x8) | FT93C46(x16) | FT93C46(x8) | FT93C46A(x16) |
(1kb) FT93C46A(x8) | GSC93BC46A(x16) | GSC93BC46A(x8) | GT93C46(x16) | GT93C46(x8) | GT93C46A(x16) | GT93C46A(x8) | HT93LC46-A(x16) | HT93LC46-A(x8) | IN93AA46A
| IN93AA46B | IN93AA46C(x16) | IN93AA46C(x8) | IN93LC46A | IN93LC46B | IN93LC46C(x16) | IN93LC46C(x8) | IS93C46-3 | IS93C46A(x16) | IS93C46A(x8) |
IS93C46AGR(x16) | IS93C46AGR(x8) | IS93C46B | IS93C46BGR | IS93C46D(x16) | IS93C46D(x8) | IS93C46DGR(x16) | IS93C46DGR(x8) | K93C46 | KM93C46 | KM93C46GD
| KM93C46V | KM93C46VGD | LC46 | M93C46(x16) | M93C46(x8) | M93S46 | MAX93LC46 | MC93C46 | MM93C46-3 | MM93C46-3GR | NM93C46 | NM93C46A | NM93C46A(x16)
| NM93C46A(x8) | NM93C46L | NM93C46LZ | NM93CS46 | NMC9346 | PTK93LC46(x16) | PTK93LC46(x8) | RH76 | RT93LC46(x16) | RT93LC46(x8) | S93462 | S93463 |
- 40 -
S93A46 | S-93A46A | S-93A46B | S-93L46AD | S93VP462 | S93VP463 | S93WD462 | S93WD463 | T93C46(x16) | T93C46(x8) | T93C46A(x16) | T93C46A(x8) | TMC93LC46 |
TMC93LC46(x16) | TMC93LC46(x8) | TU93C46(x16) | TU93C46(x8) | UG93C46-A(x16) | UG93C46-A(x8) | W93C46 | W93C46B(x16) | W93C46B(x8) | XL93C46 | XL93LC46 |
XL93LC46A | XL93LC46ARY | XL93LC46B(x16) | XL93LC46B(x8) | XL93LC46BRY(x16) | XL93LC46BRY(x8) | XL93LC46RY | Y93LC46(x16)
93AA56 | 93AA56A | 93AA56B | 93AA56C | 93C56 | 93C56A | 93C56B | 93C56C | 93CX56 | 93LC56 | 93LC56A | 93LC56B | 93LC56C | 93S56 | 93X56 | A93C56(x16) |
A93C56(x8) | AF93BC56(x16) | AF93BC56(x8) | AK93C56 | AM93LC56 | AT93C56(x16) | AT93C56(x8) | AT93C56A | AT93C56B | AT93C56C | AT93C56D(x16) | AT93C56D(x8)
| AT93C56E | AT93C57(x16) | AT93C57(x8) | BL93C56(x16) | BL93C56(x8) | BR93A56 | BR93C56 | BR93L56 | BR93LC56 | CAT93C56(x16) | CAT93C56(x8) | CAT93C56A |
CAT93C56AH | CAT93C56B(x16) | CAT93C56B(x8) | CAT93C56H(x16) | CAT93C56H(x8) | CAT93C56R(x8) | CAT93C57(x16) | CAT93C57(x8) | CAT93HC56(x16) |
CAT93HC56(x8) | CR93C56(x16) | CR93C56(x8) | EC93C56A(x16) | EC93C56A(x8) | EM93LC56(x16) | EM93LC56(x8) | EM93LC57(x16) | EM93LC57(x8) | FM93C56 |
FM93C56A(x16) | FM93C56A(x8) | FT93C56(x16) | FT93C56(x8) | FT93C56A(x16) | FT93C56A(x8) | GSC93BC56A(x16) | GSC93BC56A(x8) | GT93C56(x16) | GT93C56(x8) |
93..56 GT93C56A(x16) | GT93C56A(x8) | HT93LC56-A(x16) | HT93LC56-A(x8) | IN93AA56A | IN93AA56B | IN93AA56C(x16) | IN93AA56C(x8) | IN93LC56A | IN93LC56B |
(2kb) IN93LC56C(x16) | IN93LC56C(x8) | IS93C56-3 | IS93C56A(x16) | IS93C56A(x8) | IS93C56AGR(x16) | IS93C56AGR(x8) | IS93C56B | IS93C56BGR | IS93C56D(x16) |
IS93C56D(x8) | IS93C56DGR(x16) | IS93C56DGR(x8) | K93C56 | KM93C56 | KM93C56GD | KM93C56V | KM93C56VGD | KM93C57(x16) | KM93C57GD(x16) | KM93C57V(x16)
| M93C56(x16) | M93C56(x8) | M93S56 | MC93C56 | MM93C56-3 | MM93C56-3GR | NM93C56 | NM93C56A | NM93C56A(x16) | NM93C56A(x8) | NM93C56L | NM93C56LZ |
NM93CS56 | PTK93LC56(x16) | PTK93LC56(x8) | S93A56 | S-93A56A | S-93A56B | S-93L56AD | ST93CS56 | ST93CS57 | T93C56(x16) | T93C56(x8) | T93C56A(x16) |
T93C56A(x8) | TMC93LC56 | TMC93LC56(x16) | TMC93LC56(x8) | TMC93LC57(x16) | TMC93LC57(x8) | TU93C56(x16) | TU93C56(x8) | UG93C56-A(x16) | UG93C56-A(x8) |
UG93C56-C | W93C56 | W93C56B(x16) | W93C56B(x8) | XL93C56 | XL93LC56 | XL93LC56A | XL93LC56ARY | XL93LC56B(x16) | XL93LC56B(x8) | XL93LC56BRY(x16) |
XL93LC56BRY(x8) | XL93LC56RY | Y93LC56-A(x16)
93AA66 | 93AA66A | 93AA66B | 93AA66C | 93C66 | 93C66A | 93C66B | 93C66C | 93CX66 | 93LC66 | 93LC66A | 93LC66B | 93LC66C | 93S66 | 93X66 | A93C66(x16) |
A93C66(x8) | AF93BC66(x16) | AF93BC66(x8) | AK93C66 | AM93LC66 | AT93C66(x16) | AT93C66(x8) | AT93C66A | AT93C66B | AT93C66C | AT93C66D(x16) | AT93C66D(x8)
| AT93C66E | BL93C66(x16) | BL93C66(x8) | BR93A66 | BR93C66 | BR93L66 | BR93LC66 | CAT93C66(x16) | CAT93C66(x8) | CAT93C66A | CAT93C66AH | CAT93C66B(x16) |
CAT93C66B(x8) | CAT93C66H(x16) | CAT93C66H(x8) | CAT93C66R(x8) | CAT93HC66(x16) | CAT93HC66(x8) | CR93C66(x16) | CR93C66(x8) | EC93C66A(x16) |
EC93C66A(x8) | EM93LC66(x16) | EM93LC66(x8) | FM93C66 | FM93C66A(x16) | FM93C66A(x8) | FT93C66(x16) | FT93C66(x8) | FT93C66A(x16) | FT93C66A(x8) |
GSC93BC66A(x16) | GSC93BC66A(x8) | GT93C66(x16) | GT93C66(x8) | GT93C66A(x16) | GT93C66A(x8) | HT93LC66-A(x16) | HT93LC66-A(x8) | IN93AA66A | IN93AA66B |
93..66
IN93AA66C(x16) | IN93AA66C(x8) | IN93LC66A | IN93LC66B | IN93LC66C(x16) | IN93LC66C(x8) | IS93C66-3 | IS93C66A(x16) | IS93C66A(x8) | IS93C66AGR(x16) |
(4kb)
IS93C66AGR(x8) | IS93C66B | IS93C66BGR | IS93C66D(x16) | IS93C66D(x8) | IS93C66DGR(x16) | IS93C66DGR(x8) | K93C66 | KM93C66 | KM93C66GD | KM93C66V |
KM93C66VGD | KM93C67(x16) | KM93C67GD(x16) | KM93C67V(x16) | M93C66(x16) | M93C66(x8) | M93S66 | MC93C66 | MM93C66-3 | MM93C66-3GR | NM93C66 |
NM93C66A | NM93C66A(x16) | NM93C66A(x8) | NM93C66L | NM93C66LZ | NM93CS66 | PTK93LC66(x16) | PTK93LC66(x8) | S93662 | S93663 | S93A66 | S93A66A | S-
93A66A | S-93A66B | S-93L66AD | S93VP662 | S93VP663 | S93WD662 | S93WD663 | T93C66(x16) | T93C66(x8) | T93C66A(x16) | T93C66A(x8) | TMC93LC66 |
TMC93LC66(x16) | TMC93LC66(x8) | TU93C66(x16) | TU93C66(x8) | UG93C66-A(x16) | UG93C66-A(x8) | W93C66 | W93C66B(x16) | W93C66B(x8) | XL93C66 | XL93LC66 |
XL93LC66A | XL93LC66ARY | XL93LC66B(x16) | XL93LC66B(x8) | XL93LC66BRY(x16) | XL93LC66BRY(x8) | XL93LC66RY | Y93LC66-A(x16)
93AA76 | 93AA76A | 93AA76B | 93AA76C | 93C76 | 93C76A | 93C76B | 93C76C | 93CX76 | 93LC76 | 93LC76A | 93LC76B | 93LC76C | 93X76 | A93C76(x16) | A93C76(x8) |
93..76 AF93BC76(x16) | AF93BC76(x8) | AK93C76 | AM93LC76 | AT93C76(x16) | AT93C76(x8) | AT93C76A | AT93C76B | AT93C76C | AT93C76D(x16) | AT93C76D(x8) | AT93C76E |
(8kb) BL93C76(x16) | BL93C76(x8) | BR93A76 | BR93C76 | BR93L76 | BR93LC76 | CAT93C76(x16) | CAT93C76(x8) | CAT93C76A | CAT93C76AH | CAT93C76B(x16) |
CAT93C76B(x8) | CAT93C76H(x16) | CAT93C76H(x8) | CAT93C76R(x8) | CAT93HC76(x16) | CAT93HC76(x8) | CR93C76(x16) | CR93C76(x8) | EC93C76A(x16) |
- 41 -
EC93C76A(x8) | EM93LC76(x16) | EM93LC76(x8) | FM93C76 | FM93C76A(x16) | FM93C76A(x8) | FT93C76(x16) | FT93C76(x8) | FT93C76A(x16) | FT93C76A(x8) |
GSC93BC76A(x16) | GSC93BC76A(x8) | GT93C76(x16) | GT93C76(x8) | GT93C76A(x16) | GT93C76A(x8) | HT93LC76-A(x16) | HT93LC76-A(x8) | IN93AA76A | IN93AA76B |
IN93AA76C(x16) | IN93AA76C(x8) | IN93LC76A | IN93LC76B | IN93LC76C(x16) | IN93LC76C(x8) | IS93C76-3 | IS93C76A(x16) | IS93C76A(x8) | IS93C76AGR(x16) |
IS93C76AGR(x8) | IS93C76B | IS93C76BGR | IS93C76D(x16) | IS93C76D(x8) | IS93C76DGR(x16) | IS93C76DGR(x8) | K93C76 | KM93C76 | KM93C76GD | KM93C76V |
KM93C76VGD | M93C76(x16) | M93C76(x8) | MC93C76 | MM93C76-3 | MM93C76-3GR | NM93C76 | NM93C76A | NM93C76A(x16) | NM93C76A(x8) | NM93C76L | NM93C76LZ |
PTK93LC76(x16) | PTK93LC76(x8) | S-93A76A | S-93A76B | S-93L76AD | T93C76(x16) | T93C76(x8) | T93C76A(x16) | T93C76A(x8) | TMC93LC76 | TMC93LC76(x16) |
TMC93LC76(x8) | W93C76 | W93C76B(x16) | W93C76B(x8) | XL93C76 | XL93LC76 | XL93LC76A | XL93LC76ARY | XL93LC76B(x16) | XL93LC76B(x8) | XL93LC76BRY(x16) |
XL93LC76BRY(x8) | XL93LC76RY
93AA86 | 93AA86A | 93AA86B | 93AA86C | 93C86 | 93C86A | 93C86B | 93C86C | 93CX86 | 93LC86 | 93LC86A | 93LC86B | 93LC86C | 93X86 | A93C86(x16) | A93C86(x8) |
AF93BC86(x16) | AF93BC86(x8) | AK93C86 | AM93LC86 | AT93C86(x16) | AT93C86(x8) | AT93C86A | AT93C86B | AT93C86C | AT93C86D(x16) | AT93C86D(x8) | AT93C86E |
BL93C86(x16) | BL93C86(x8) | BR93A86 | BR93C86 | BR93L86 | BR93LC86 | CAT93C86(x16) | CAT93C86(x8) | CAT93C86A | CAT93C86AH | CAT93C86B(x16) |
CAT93C86B(x8) | CAT93C86H(x16) | CAT93C86H(x8) | CAT93C86R(x8) | CAT93HC86(x16) | CAT93HC86(x8) | CR93C86(x16) | CR93C86(x8) | EC93C86A(x16) |
EC93C86A(x8) | EM93LC86(x16) | EM93LC86(x8) | FM93C86 | FM93C86A(x16) | FM93C86A(x8) | FT93C86(x16) | FT93C86(x8) | FT93C86A(x16) | FT93C86A(x8) |
93..86 GSC93BC86A(x16) | GSC93BC86A(x8) | GT93C86(x16) | GT93C86(x8) | GT93C86A(x16) | GT93C86A(x8) | HT93LC86-A(x16) | HT93LC86-A(x8) | IN93AA86A | IN93AA86B |
(16kb) IN93AA86C(x16) | IN93AA86C(x8) | IN93LC86A | IN93LC86B | IN93LC86C(x16) | IN93LC86C(x8) | IS93C86-3 | IS93C86A(x16) | IS93C86A(x8) | IS93C86AGR(x16) |
IS93C86AGR(x8) | IS93C86B | IS93C86BGR | IS93C86D(x16) | IS93C86D(x8) | IS93C86DGR(x16) | IS93C86DGR(x8) | K93C86 | KM93C86 | KM93C86GD | KM93C86V |
KM93C86VGD | M93C86(x16) | M93C86(x8) | MC93C86 | MM93C86-3 | MM93C86-3GR | NM93C86 | NM93C86A | NM93C86A(x16) | NM93C86A(x8) | NM93C86L | NM93C86LZ |
PTK93LC86(x16) | PTK93LC86(x8) | S93A86 | S93A86A | S-93A86A | S-93A86B | S-93L86AD | T93C86(x16) | T93C86(x8) | T93C86A(x16) | T93C86A(x8) | TMC93LC86 |
TMC93LC86(x16) | TMC93LC86(x8) | W93C86 | W93C86B(x16) | W93C86B(x8) | XL93C86 | XL93LC86 | XL93LC86A | XL93LC86ARY | XL93LC86B(x16) | XL93LC86B(x8) |
XL93LC86BRY(x16) | XL93LC86BRY(x8) | XL93LC86RY
9.7. EEPROM 1-Wire
24..30
24..31
DS2430A | DS2431 | DS2433 | DS24B33 | DS2436
24..33
24..36
- 42 -
9.8. FLASH SPI 25… series
Supports low-voltage serial flash memories (1.5V, 1.8V, 2.5V) and standard (3.3V)
A25L05P | A25L512 | A25L512A | A25LS512A | AC25LV512 | AT25DL5121 | AT25DN512C | AT25F512 | AT26DF5121 | EN25B05 | EN25F05 | EN25P05 | F25D512Q |
25..05 F25L0512 | F25L05P | F25L05PA | F25L512P | F25L512Q | GD25D05C | GD25Q05 | GD25WD05C | KH25L512 | M25P05 | M25P05-A | MS25X512 | MX25L512 | MX25L5121 |
(512kb) MX25L5121E | MX25L512C | MX25L512E | MX25R512F | MX25U5121E | MX25V512 | MX25V5121E | MX25V512C | MX25V512E | MX25V512F | PM25LD512 | PM25LV512 |
PM25LV512A | SA25F005 | SST25VF512 | SST25VF512A | SST25WF512 | SST25WF512B | W25Q05CL | W25Q05CV | W25X05CL
A25L010 | A25L010A | A25L10P | AC25LV010 | AT24F1024 | AT25DN011 | AT25FS010 | EN24LF10 | EN25B10 | EN25F10 | EN25LF10 | EN25P10 | EN25S10 | ES25P10 |
F25L01P | F25L01PA | GD25D10C | GD25Q10 | GD25WD10C | IS25CD010 | IS25LQ010B | KH25L1005 | LE25FU106 | LE25FU106B | M25P10 | M25P10-A | M25PE10 |
25..010 MS25X10 | MX25L1005 | MX25L1005C | MX25L1005ZM | MX25L1006 | MX25L1006E | MX25L1021 | MX25L1021E | MX25L1025 | MX25L1025C | MX25L1026 | MX25L1026E |
(1Mb) MX25R1035F | MX25U1001E | MX25V1006 | MX25V1006E | MX25V1035F | NX25P10 | PM25LD010 | PM25LV010 | PM25LV010A | S25FL001D | SA25F010 | SST25VF010 |
SST25VF010A | SST25WF010 | TS25L010A | W25D10V | W25P10V | W25Q10BV | W25Q10CL | W25Q10CV | W25Q10EW | W25X10AV | W25X10BL | W25X10BV | W25X10CL
| W25X10L | W25X10V
A25L020 | A25L020C | A25L20P | AT25DF021 | AT25F2048 | AT25F2048N | AT25PE20 | AT25PE20[P264] | EN25B20 | EN25F20 | EN25LF20 | EN25P20 | EN25S20 | ES25P20
| F25D02P | F25D02QA | F25L02P | F25L02PA | GD25D20C | GD25Q20B | GD25Q21B | GD25WD20C | IS25LQ020 | IS25WD020 | IS25WP020D | IS25WQ020 | KH25L2005 |
25..020 LE25FU206 | LE25S20 | LE25U20 | M25P20 | M25PE20 | M25U2033E | MS25X20 | MX25L2005 | MX25L2005C | MX25L2005ZM | MX25L2006 | MX25L2025C | MX25L2026E |
(2Mb) MX25L26C | MX25R2035F | MX25U2032E | MX25U2033E | MX25U2035F | MX25V2006E | MX25V2033F | MX25V2035F | NX25P20 | PM25LD020 | PM25LV020 | S25FL002D |
SA25F020 | SST25VF020 | SST25VF020A | SST25VF020B | SST25WF020 | SST25WF020B | TS25L020A | W25D20V | W25P20V | W25Q20BW | W25Q20CL | W25Q20CV |
W25Q20EW | W25X20BL | W25X20BV | W25X20CL | XM25QU20B
A25L040 | A25L040A | A25L40P | AT25DF041 | AT25DF041A | AT25F4096 | AT25FF041A | AT25FS040 | AT25PE40 | AT25PE40[P264] | AT25SF041 | AT25XE041D |
AT26F004 | EN25B40 | EN25F40 | EN25LF40 | EN25P40 | EN25Q40 | EN25S40 | EN25T40 | ES25M40 | ES25P40 | F25D04Q | F25D04QA | F25L004 | F25L04P | F25L04PA |
GD25D40C | GD25LQ40 | GD25Q40B | GD25Q41B | GD25WD40C | IS25LD040 | IS25LQ040B | IS25WD040 | IS25WP040 | IS25WP040D | IS25WQ040 | KH25L4005A |
25..040 KH25L4006E | LE25FS406 | LE25FU406B | LE25S40 | LE25U40 | M25P40 | M25PE40 | MS25X40 | MX25L4005 | MX25L4005A | MX25L4005C | MX25L4006E | MX25L4025C |
(4Mb) MX25L4026E | MX25R4035F | MX25U4032F | MX25U4033E | MX25U4035 | MX25U4035F | MX25V4005 | MX25V4005C | MX25V4006E | MX25V4035 | NX25P40 | PM25LD040 |
PM25LV040 | S25FL004 | S25FL004A | S25FL004K | S25FL204K | SA25F040 | SST25VF040 | SST25VF040A | SST25VF040B | SST25WF040 | SST25WF040B | W25D40V |
W25P40V | W25Q40BL | W25Q40BV | W25Q40BW | W25Q40CL | W25Q40EW | W25X40AL | W25X40AV | W25X40BL | W25X40BV | W25X40CL | W25X40L | W25X40V |
XM25QH40B | XM25QU40B
A25L080 | A25L80P | AT25DF081 | AT25DF081A | AT25DL081 | AT25FF081A | AT25PE80 | AT25PE80[P264] | AT25SF081 | AT25XE081D | AT26DF081 | EN25B80 | EN25D80
| EN25F80 | EN25P80 | EN25Q80 | EN25Q80A | EN25S80 | EN25T80 | ES25M80 | ES25P80 | F25D08QA | F25L08QA | FM25Q08 | FM25Q08A | GD25D80C | GD25LQ80 |
25..080 GD25Q80B | GD25Q80C | GD25WD80C | IS25LP080D | IS25LQ080 | IS25LQ080B | IS25WP080 | IS25WP080D | KH25L8005 | KH25L8006E | KH25L8036D | LE25S81 |
(8Mb) M25P80 | M25PE80 | M25PX80 | M25X80 | MS25X80 | MX25L8005 | MX25L8005ZM | MX25L8006E | MX25L8008E | MX25L8035E | MX25L8036E | MX25L8073E | MX25L8075E
| MX25R8035F | MX25U8032E | MX25U8033E | MX25U8035 | MX25U8035E | MX25U8035F | MX25V8005 | MX25V8006E | MX25V8035F | NX25P80 | PM25LV080 |
PM25LV080B | S25FL008A | S25FL008K | S25FL208K | SST25VF080B | SST25WF080 | SST25WF080B | TS25L80P | W25D80V | W25P80V | W25Q40CL | W25Q80BL |
- 43 -
W25Q80BV | W25Q80BW | W25Q80DL | W25Q80DV | W25Q80EW | W25Q80FV | W25Q80JV | W25X80AL | W25X80AV | W25X80BV | W25X80L | W25X80V | XM25QH80B |
XM25QU80B
A25L016 | A25L16P | A25LQ16 | AT25DF161 | AT25DL161 | AT25FF161A | AT25PE16 | AT25PE16[P528] | AT25SF161 | AT25XE161D | AT26DF161 | EN25B16 | EN25D16 |
EN25F16 | EN25P16 | EN25Q16A | EN25QA16 | EN25QH16 | EN25S16 | EN25T16 | ES25M16 | ES25P16 | F16 | F25L016 | F25L16P | F25L16PA | F25L16Q | F25L16QA |
FM25Q16 | FM25Q16A | FM25Q16B | FM25S16A | GD25LQ16 | GD25Q16B | IS25LP016D | IS25LQ016B | IS25WP016 | IS25WP016D | KH25L1605A | KH25L1605D |
25..016 KH25L1606E | KH25L1635D | LE25S161 | M25P16 | M25PE16 | M25PX16 | M25X16 | MS25X16 | MX25L1605 | MX25L1605A | MX25L1605D | MX25L1606E | MX25L1608D |
(16Mb) MX25L1608E | MX25L1633E | MX25L1635D | MX25L1635E | MX25L1636D | MX25L1636E | MX25L1673E | MX25L1675E | MX25R1635F | MX25U1633F | MX25U1635E |
MX25U1635F | MX25V1635F | N25Q016 | NX25P16 | PM25LV016 | PM25LV016B | Q16 | QB25F016S33B | QH25F016S33B | S25FL016 | S25FL016A | S25FL016K | S25FL116K
| S25FL216K | SA25F160 | SST25VF016B | TS25L16AP | TS25L16BP | TS25L16P | W25Q16BF | W25Q16BV | W25Q16CL | W25Q16CV | W25Q16DV | W25Q16DW |
W25Q16FW | W25Q16JL | W25Q16JV | W25Q16VF | W25X16AL | W25X16AV | W25X16BV | W25X16V | XM25QH16B | XM25QU16B
A25L032 | A25LQ32A | AT25DF321 | AT25DF321A | AT25FF321A | AT25QL321 | AT25SF321 | AT25SL321 | AT25XE321D | AT26DF321 | AT26SD321 | ATXP32 | EN25B32 |
EN25F32 | EN25P32 | EN25Q32B | EN25QA32 | EN25QH32 | EN25S32 | ES25P32 | F25L32P | F25L32PA | F25L32Q | F25L32QA | F32 | FM25Q32 | FM25Q32A | GD25B32C |
GD25LB32D | GD25LQ32 | GD25LQ32C | GD25Q32B | GD25Q32C | IS25CQ032 | IS25CQ032A | IS25LP032D | IS25LQ032B | IS25WP032 | IS25WP032D | KH25L3205D |
25..032 KH25L3206E | M25P32 | M25PE32 | M25PX32 | M25X32 | MX25L3205A | MX25L3205D | MX25L3206 | MX25L3206E | MX25L3208D | MX25L3208E | MX25L3225D |
(32Mb) MX25L3233F | MX25L3235D | MX25L3235E | MX25L3236D | MX25L3236E | MX25L3236F | MX25L3237D | MX25L3239E | MX25L3255E | MX25L3273E | MX25L3273F |
MX25L3275E | MX25R3235F | MX25U3235E | MX25U3235F | MX25U3273F | N25Q032 | NX25P32 | Q32 | QB25F320S33B | QH25F320S33B | S25FL032 | S25FL032A |
S25FL032K | S25FL032P | S25FL132K | SA25F320 | SST25VF032B | W25Q32BV | W25Q32DW | W25Q32FV | W25Q32FW | W25Q32JV | W25Q32JW | W25Q32V | W25Q32VF
| W25X32AV | W25X32BV | W25X32V | XM25QH32B | XM25QU32B | XM25QW32C
A25LMQ64 | A25LQ64 | AT25DF641A | AT25QF641 | AT25QL641 | AT25SF641 | AT25SL641 | ATXP64 | EN25F64 | EN25Q64 | EN25QA64 | EN25QH64 | EN25S64 | F25D64QA
| F25L64QA | F64 | FM25Q64 | FM25Q64A | GD25B64 | GD25B64C | GD25LB64C | GD25LQ64B | GD25LQ64C | GD25Q64B | GD25Q64C | IS25LP064 | IS25LP064A |
IS25WP064 | IS25WP064A | KH25L6405D | KH25L6406E | M25P64 | M25PX64 | MT25QL064A | MT25QU064A | MX25L64 | MX25L6405 | MX25L6405D | MX25L6406E |
25..064 MX25L6408 | MX25L6408D | MX25L6408E | MX25L6433 | MX25L6433F | MX25L6435 | MX25L6435E | MX25L6436E | MX25L6436F | MX25L6439 | MX25L6439E | MX25L6445E
(64Mb) | MX25L6455E | MX25L6456 | MX25L6456E | MX25L6456F | MX25L6465E | MX25L6473E | MX25L6473F | MX25L6475E | MX25R6435F | MX25U6435 | MX25U6435E |
MX25U6435F | MX25U6473 | MX25U6473F | N25Q064 | N25Q064A11 | N25Q064A13 | Q64 | QB25F640S33B | QH25F640S33B | S25FL064A | S25FL064K | S25FL064L |
S25FL064P | S25FL164K | S25FS064S | S64 | SST25VF064C | W25Q64BV | W25Q64CV | W25Q64DW | W25Q64FV | W25Q64FW | W25Q64JV | W25Q64JW | W25Q64VF |
W25X64BV | W25X64V | XM25QH64A | XM25QU64A | XM25QW64C
AT25QF128A | AT25QL128A | AT25SL128A | ATXP128 | EN25Q128 | EN25QA128 | EN25QH128 | EN25QH128A | F25D128QA | F25L128QA | GD25B127D | GD25B128 |
GD25LB128D | GD25LQ128 | GD25LQ128C | GD25LQ128D | GD25Q127 | GD25Q128B | GD25Q128C | IS25LP128 | IS25LP128F | IS25WP128 | IS25WP128F | KH25L12845E |
25..128 M25P128 | MT25QL128A | MT25QU128A | MX25L128 | MX25L12805D | MX25L12835E | MX25L12835F | MX25L12836E | MX25L12839F | MX25L12845E | MX25L12845G |
(128Mb) MX25L12850F | MX25L12855E | MX25L12855F | MX25L12865E | MX25L12865F | MX25L12873F | MX25L12873G | MX25L12875F | MX25LM12845G | MX25U128 |
MX25U12835F | MX25U12873F | MX25U12890F | MX25UM12845G | N25Q128 | N25Q128A11 | N25Q128A13 | Q128 | S25FL127S | S25FL128K | S25FL128L | S25FL128P |
S25FL128S | S25FL129P | S25FS128S | W25Q128BV | W25Q128FV | W25Q128FW | W25Q128JV | W25Q128JW | XM25QH128A | XM25QU128C | XM25QW128C
25..256 EN25QA256 | EN25QH256 | EN25QH256A | EN25S256 | GD25B256D | GD25B257D | GD25LB256D | GD25LQ256 | GD25LQ256C | GD25LQ256D | GD25Q256 | GD25Q257D |
(256Mb) IS25LP256D | IS25LP256E | IS25WP256D | MT25QL256A | MT25QU256A | MX25L25635E | MX25L25635F | MX25L25639F | MX25L25645G | MX25L25655E | MX25L25655F |
- 44 -
MX25L25673G | MX25L25735E | MX25L25735F | MX25L25835E | MX25L25855E | MX25LM25645G | MX25U25635F | MX25U25645G | MX25UM25645G | N25Q256A11 |
N25Q256A13 | N25Q256A33 | N25Q256A73 | N25Q256A81 | N25Q256A83 | S25FL256L | S25FL256P | S25FL256S | S25FS256S | W25Q256FV | W25Q256JV | W25Q256JW |
W25Q257FV | W25Q257JV | XM25QH256B | XM25QU256B | XM25QW256C
25..512 GD25Q512 | IS25LE512M | IS25LP512M | IS25WP512M | MT25QL512A | MT25QU512A | MX25L51237G | MX25L51245G | MX25L51255G | MX25LM51245G | MX25U51245G |
(512Mb) MX25UM51245G | MX66L51235F | MX66U51235F | S25FL512S | S25FS512S | W25Q512JV
25..01
MT25QL01G | MT25QU01G | W25Q01JV
(1Gb)
25..02
MT25QL02G | MT25QU02G
(2Gb)
9.9. FLASH SPI 26… series
Supports low-voltage serial flash memories (1.8V) and standard (3.3V)
(4Mb - SST26VF040A | SST26WF040B | SST26WF040BA | SST26VF080A | SST26WF080B | SST26WF080BA | SST26VF016 | SST26VF016B | SST26WF016B | SST26WF016BA |
64Mb) SST26VF032 | SST26VF032B | SST26VF032BA | SST26VF064B | SST26VF064BA | SST26VF064C | SST26VF064CA | SST26WF064C | SST26WF064CA
9.10. FLASH SPI 45… series (DATA FLASH)
M45PE10 | AT45DB011 | AT45DB011D | M45PE20 | AT45DB021 | AT45DB021D | AT45DB021E | M45PE40 | AT45DB041 | AT45DB041D | AT45DB041E | M45PE80 | AT45DB081
(1Mb -
| AT45DB081D | AT45DB081E | M45PE16 | AT45DB161 | AT45DB161D | AT45DB161E | AT45DQ161 | AT45DB321 | AT45DB321D | AT45DB321E | AT45DQ321 | AT45DB641E |
64Mb)
AT45DB642 | AT45DB642D
9.11. FLASH SPI NAND
GD5F1GQ4RB | GD5F1GQ4RC | GD5F1GQ4RE | GD5F1GQ4RF | GD5F1GQ4UB | GD5F1GQ4UC | GD5F1GQ4UE | GD5F1GQ4UF | IS37SML01G1 | IS38SML01G1 |
MT29F1G01AAADD | MT29F1G01ABAFD | MT29F1G01ABAGD | MT29F1G01ABBFD | MT29F1G01ABBGD | TC58CVG0S3HRA | TC58CYG0S3HRA | W25N01GV | W25N01GW |
(1Gb -
W25N01JW | GD5F2GQ4RB | GD5F2GQ4RC | GD5F2GQ4RE | GD5F2GQ4RF | GD5F2GQ4UB | GD5F2GQ4UC | GD5F2GQ4UE | GD5F2GQ4UF | MT29F2G01AAAED |
4Gb)
MT29F2G01ABAGD | MT29F2G01ABBGD | TC58CVG1S3HRA | TC58CYG1S3HRA | W25N02JW | W25N02KV | MT29F4G01ABAFD | MT29F4G01ABBFD | MT29F4G01ADAGD |
TC58CVG2S0HRA | TC58CYG2S0HRA
- 45 -
9.12. FRAM I2C 24… series
FM24C04 | FM24C04B | FM24CL04 | FM24CL04B | MB85RC04V | FM24C16 | FM24C16B | FM24CL16 | FM24CL16B | FM25C160B | MB85RC16 | MB85RC16V | FM24C64 |
(4kb -
FM24C64B | FM24CL64 | FM24CL64B | MB85RC64 | MB85RC64A | MR44V064B | FM24V01 | MB85RC128 | MB85RC128A | FM24V02 | FM24V02A | FM24W256 | MB85RC256V |
2Mb)
FM24V05 | FM24V10 | FM24VN10 | MR44V100A | MR44V200A
9.13. FRAM SPI 25… series
FM25040 | FM25040B | FM2504B | FM25CL04B | FM25L04 | FM25L04B | FM25C160 | FM25C160B | FM25L16 | FM25L16B | MR45V032A | FM25640 | FM25640B | FM25CL64 |
(4kb - FM25CL64B | MB85RS64 | MB85RS64A | MR45V064B | FM25V01 | FM25V01A | MB85RS128A | MB85RS128B | FM25V02 | FM25V02A | FM25W256 | MB85RS256A | MB85RS256B
8Mb) | MR45V256A | FM25V05 | FM25V10 | FM25VN10 | MR45V100 | CY15B102Q | CY15V102Q | FM25H20 | FM25V20 | FM25V20A | MR45V200 | CY15B104Q | CY15V104Q |
CY15B108Q | CY15V108Q
9.14. Optical and ethernet modules (SFP/SFP+ transceivers)
Please note!
• there is SFP/QSFP/XFP adapter required with external power supply,
• MSA standard is supported (e.g. SFF-8472, SFF-8636, INF-8077i),
• possibility to enter manufacturer/host password and program write protected transceivers,
• brute force password tool (searching password for protected transceivers with unknown password),
• change manufacturer info, model, serial number etc. and recalculate checksums directly from REVELPROG-IS application
SFP and SFP+, read/write block 0xA0 (256B), read block 0xA2 (256B), read/write page 0-255 (128B), standard MSA
SFP / SFP+
example manufacturers: GBC, HUAWEI, GPON, JDSU, MIKROTIK, OPTEC, OPTION, WTD and other OEM
QSFP and QSFP+, read/write A0h block (256B), read/write 0-255 page (128B), standard MSA
QSFP / QSFP+
example manufacturers: CISCO, HP, FINISAR, NOKIA, HUAWEI, JDSU and other OEM
XFP, read/write A0h block (256B), read/write 0-255 table (128B), standard MSA
XFP
example manufacturers: 10GTEK, CISCO, FINISAR, OPNEXT, JDSU and other OEM
- 46 -
9.15. Your suggestions
If you have any suggestion for supported device list please contact us at [email protected]. There is possibility to add any serial device
with I2C, SPI or uWire interface (EEPROM/FLASH/FRAM).
- 47 -
11. APPENDIX B - video tutorials and technical support
Programming examples on youtube:
https://www.youtube.com/playlist?list=PLKdrjJPMLd8KBX12vHdyCg_0JfNT0Aw7U
REVELTRONICS' forum:
https://forum.reveltronics.com/viewforum.php?f=17
- 48 -
You might also like
- Programming Manual: For Personal ComputerNo ratings yetProgramming Manual: For Personal Computer236 pages
- Um2237 Stm32cubeprogrammer Software Description StmicroelectronicsNo ratings yetUm2237 Stm32cubeprogrammer Software Description Stmicroelectronics175 pages
- FX5 ProgrammingManual Instructions-StandardFunctions-FunctionBlocks JY997D55801-HNo ratings yetFX5 ProgrammingManual Instructions-StandardFunctions-FunctionBlocks JY997D55801-H1,096 pages
- Xper Information Management System 2.3 IFU EN USNo ratings yetXper Information Management System 2.3 IFU EN US180 pages
- Fdocuments - in - Docklight Scripting v22 User Manual 072016 PDFNo ratings yetFdocuments - in - Docklight Scripting v22 User Manual 072016 PDF167 pages
- Kami Export - GIOVANNI MURO - 2023-24 IM1 Chapter 6 Systems of EquationsNo ratings yetKami Export - GIOVANNI MURO - 2023-24 IM1 Chapter 6 Systems of Equations80 pages
- 16-Bit MCU With MAC Unit, 512 Kbyte Flash Memory and 18 Kbyte RAMNo ratings yet16-Bit MCU With MAC Unit, 512 Kbyte Flash Memory and 18 Kbyte RAM239 pages
- Dm00403500-Stm32cubeprogrammer-Software-Description-Stmicroelectronics (1) - CompressedNo ratings yetDm00403500-Stm32cubeprogrammer-Software-Description-Stmicroelectronics (1) - Compressed169 pages
- Stm32cubeprogrammer Software Description StmicroelectronicsNo ratings yetStm32cubeprogrammer Software Description Stmicroelectronics84 pages
- STM32CubeProgrammer - User Manual GuideNo ratings yetSTM32CubeProgrammer - User Manual Guide145 pages
- M29W640FT M29W640FB: 64 Mbit (8Mb x8 or 4Mb x16, Page, Boot Block) 3V Supply Flash MemoryNo ratings yetM29W640FT M29W640FB: 64 Mbit (8Mb x8 or 4Mb x16, Page, Boot Block) 3V Supply Flash Memory73 pages
- Bosch Protocol Technical Information: en Application NoteNo ratings yetBosch Protocol Technical Information: en Application Note10 pages
- BSP and Device Driver Development Guide: On-Line Applications Research CorporationNo ratings yetBSP and Device Driver Development Guide: On-Line Applications Research Corporation106 pages
- Universal IC Programmer - Autoelectric TL866CSNo ratings yetUniversal IC Programmer - Autoelectric TL866CS7 pages
- Instruction Manual Universal Fieldbus-Gateway Unigate Ic - ProfibusNo ratings yetInstruction Manual Universal Fieldbus-Gateway Unigate Ic - Profibus63 pages
- Skill-Lync - Aerospace Offerings - 2024No ratings yetSkill-Lync - Aerospace Offerings - 202432 pages
- Physics - Phy-H-Dse-T-03 (Communication Electronics)No ratings yetPhysics - Phy-H-Dse-T-03 (Communication Electronics)2 pages
- BSP and Device Driver Development Guide: On-Line Applications Research CorporationNo ratings yetBSP and Device Driver Development Guide: On-Line Applications Research Corporation98 pages
- Willem Pro 2 Only Intelligent ProgrammingNo ratings yetWillem Pro 2 Only Intelligent Programming24 pages
- Apple Product Information Sheet 20 Watt HoursNo ratings yetApple Product Information Sheet 20 Watt Hours8 pages
- UM2237 STM32CubeProgrammer Software DescriptionNo ratings yetUM2237 STM32CubeProgrammer Software Description39 pages
- Cs8592-Object Oriented Analysis and DesignNo ratings yetCs8592-Object Oriented Analysis and Design8 pages
- Tutorial Letter 101 - Version (20240201)No ratings yetTutorial Letter 101 - Version (20240201)18 pages
- Name: - Date: - APCSA - Loops Worksheet 1No ratings yetName: - Date: - APCSA - Loops Worksheet 12 pages
- CIS-240-101-12FA Data Communications Course SyllabusNo ratings yetCIS-240-101-12FA Data Communications Course Syllabus9 pages
- 2.a What Is A Digital System? Why Are Digital Systems So Pervasive? AnswerNo ratings yet2.a What Is A Digital System? Why Are Digital Systems So Pervasive? Answer23 pages
- The Linux Terminal for Advanced Users - The Command Line Made Easy: First EditionFrom EverandThe Linux Terminal for Advanced Users - The Command Line Made Easy: First EditionNo ratings yet
